Not recommended for new designs –
Please use 25AA320A or 25LC320A.
25AA320/25LC320/25C320
32K SPI Bus Serial EEPROM
Device Selection Table
Description:
Part
Number
VCC
Range
Max. Clock
Frequency
25AA320
1.8-5.5V
1 MHz
I
25LC320
2.5-5.5V
2 MHz
I,E
25C320
4.5-5.5V
3 MHz
I,E
Temp.
Ranges
The Microchip Technology Inc. 25AA320/25LC320/
25C320 (25XX320*) are 32 Kbit serial Electrically
Erasable PROMs. The memory is accessed via a
simple Serial Peripheral Interface (SPI) compatible
serial bus. The bus signals required are a clock input
(SCK) plus separate data in (SI) and data out (SO)
lines. Access to the device is controlled through a Chip
Select (CS) input.
Features:
Communication to the device can be paused via the
hold pin (HOLD). While the device is paused,
transitions on its inputs will be ignored, with the
exception of Chip Select, allowing the host to service
higher priority interrupts.
• Low-Power CMOS Technology:
- Write current: 3 mA maximum
- Read current: 500 μA, typical
- Standby current: 500 nA, typical
• 4096 x 8 Bit Organization
• 32 Byte Page
• Write Cycle Time: 5 ms Maximum
• Self-Timed Erase and Write Cycles
• Block Write Protection:
- Protect none, 1/4, 1/2 or all of array
• Built-in Write Protection:
- Power on/off data protection circuitry
- Write enable latch
- Write-protect pin
• Sequential Read
• High Reliability:
- Endurance: 1M E/W cycles
- Data retention: > 200 years
- ESD protection: > 4000V
• 8-Pin PDIP, SOIC and TSSOP Packages
• 14-Lead TSSOP Package
• Temperature Ranges Supported:
- Industrial (I):
-40°C to +85°C
- Automotive (E):
-40°C to +125°C
Block Diagram
STATUS
Register
I/O Control
Logic
HV Generator
EEPROM
Array
Memory
Control
Logic
XDEC
Page
Latches
SI
Y Decoder
SO
CS
SCK
Sense Amp.
R/W Control
HOLD
WP
VCC
VSS
Package Types
SO
2
WP
3
VSS
4
8
VCC
7
HOLD
6
SCK
5
SI
HOLD
1
VCC
2
CS
3
SO
4
TSSOP
8
SCK
7
SI
6
VSS
5
WP
CS
SO
NC
NC
NC
WP
VSS
1
2
3
4
5
6
7
25XX320
1
TSSOP
25XX320
CS
25XX320
PDIP, SOIC
14
13
12
11
10
9
8
VCC
HOLD
NC
NC
NC
SCK
SI
*25XX320 is used in this document as a generic part number for the 25AA320/25LC320/25C320 devices.
© 2008 Microchip Technology Inc.
DS21227F-page 1
25AA320/25LC320/25C320
1.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings(†)
VCC .............................................................................................................................................................................7.0V
All inputs and outputs w.r.t. VSS ........................................................................................................ -0.6V to VCC + 1.0V
Storage temperature .................................................................................................................................-65°C to 150°C
Ambient temperature under bias ...............................................................................................................-40°C to 125°C
ESD protection on all pins ..........................................................................................................................................4 kV
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for an
extended period of time may affect device reliability.
TABLE 1-1:
DC CHARACTERISTICS
DC CHARACTERISTICS
Param.
No.
Sym.
D1
VIH1
D2
VIH2
Characteristics
High-level input
voltage
Low-level input
voltage
Industrial (I): TA = -40°C to +85°C VCC = 1.8V to 5.5V
Automotive (E):TA = -40°C to +125°C VCC = 2.5V to 5.5V
Min.
Max.
Units
Conditions
2.0
VCC+1
V
VCC ≥ 2.7V (Note)
0.7 VCC
VCC+1
V
VCC< 2.7V (Note)
-0.3
0.8
V
VCC ≥ 2.7V (Note)
-0.3
0.3 VCC
V
VCC < 2.7V (Note)
D3
VIL1
D4
VIL2
D5
VOL
Low-level output
voltage
—
0.2
V
IOL = 1.0 mA, VCC < 2.5V
D6
VOH
High-level output
voltage
VCC -0.5
—
V
IOH = -400 μA
D7
ILI
Input leakage current
—
±1
μA
CS = VCC, VIN = VSS TO VCC
D8
ILO
Output leakage
current
—
±1
μA
CS = VCC, VOUT = VSS TO VCC
D9
CINT
Internal Capacitance
(all inputs and
outputs)
—
7
pF
TA = 25°C, CLK = 1.0 MHz,
VCC = 5.0V (Note)
D10
ICC Read Operating Current
—
—
1
500
mA
μA
VCC = 5.5V; FCLK = 3.0 MHz;
SO = Open
VCC = 2.5V; FCLK = 2.0 MHz;
SO = Open
D11
ICC Write
—
—
5
3
mA
mA
VCC = 5.5V
VCC = 2.5V
D12
ICCS
—
—
5
1
μA
μA
CS = VCC = 5.5V, Inputs tied to VCC or
VSS
CS = VCC = 2.5V, Inputs tied to VCC or
VSS
Note:
Standby Current
This parameter is periodically sampled and not 100% tested.
DS21227F-page 2
© 2008 Microchip Technology Inc.
25AA320/25LC320/25C320
TABLE 1-2:
AC CHARACTERISTICS
Industrial (I):
Automotive (E):
AC CHARACTERISTICS
Param.
No.
Sym.
Characteristic
TA = -40°C to +85°C
TA = -40°C to +125°C
VCC = 1.8V to 5.5V
VCC = 2.5V to 5.5V
Min.
Max.
Units
Conditions
—
—
—
3
2
1
MHz
MHz
MHz
VCC = 4.5V to 5.5V
VCC = 2.5V to 5.5V
VCC = 1.8V to 5.5V
1
FCLK
Clock Frequency
2
TCSS
CS Setup Time
100
250
500
—
—
—
ns
ns
ns
VCC = 4.5V to 5.5V
VCC = 2.5V to 5.5V
VCC = 1.8V to 5.5V
3
TCSH
CS Hold Time
150
250
475
—
—
—
ns
ns
ns
VCC = 4.5V to 5.5V
VCC = 2.5V to 5.5V
VCC = 1.8V to 5.5V
4
TCSD
CS Disable Time
500
—
ns
—
5
TSU
Data Setup Time
30
50
50
—
—
—
ns
ns
ns
VCC = 4.5V to 5.5V
VCC = 2.5V to 5.5V
VCC = 1.8V to 5.5V
6
THD
Data Hold Time
50
100
100
—
—
—
ns
ns
ns
VCC = 4.5V to 5.5V
VCC = 2.5V to 5.5V
VCC = 1.8V to 5.5V
7
TR
CLK Rise Time
—
2
TF
CLK Fall Time
—
2
μs
μs
(Note 1)
8
9
THI
Clock High Time
150
230
475
—
—
—
ns
ns
ns
VCC = 4.5V to 5.5V
VCC = 2.5V to 5.5V
VCC = 1.8V to 5.5V
10
TLO
Clock Low Time
150
230
475
—
—
—
ns
ns
ns
VCC = 4.5V to 5.5V
VCC = 2.5V to 5.5V
VCC = 1.8V to 5.5V
11
TCLD
Clock Delay Time
50
—
ns
—
12
TCLE
Clock Enable Time
50
—
ns
—
13
TV
Output Valid from
Clock Low
—
—
—
150
230
—
ns
ns
ns
VCC = 4.5V to 5.5V
VCC = 2.5V to 5.5V
VCC = 1.8V to 5.5V
14
THO
Output Hold Time
0
—
ns
(Note 1)
15
TDIS
Output Disable Time
—
—
—
200
250
—
ns
ns
ns
VCC = 4.5V to 5.5V (Note 1)
VCC = 2.5V to 5.5V (Note 1)
VCC = 1.8V to 5.5V
16
THS
HOLD Setup Time
100
100
200
—
—
—
ns
ns
ns
VCC = 4.5V to 5.5V
VCC = 2.5V to 5.5V
VCC = 1.8V to 5.5V
17
THH
HOLD Hold Time
100
100
200
—
—
—
ns
ns
ns
VCC = 4.5V to 5.5V
VCC = 2.5V to 5.5V
VCC = 1.8V to 5.5V
18
THZ
HOLD Low to Output
High-Z
100
150
200
—
—
—
ns
ns
ns
VCC = 4.5V to 5.5V (Note 1)
VCC = 2.5V to 5.5V (Note 1)
VCC = 1.8V to 5.5V
19
THV
HOLD High to Output
Valid
100
150
200
—
—
—
ns
ns
ns
VCC = 4.5V to 5.5V
VCC = 2.5V to 5.5V
VCC = 1.8V to 5.5V
20
TWC
Internal Write Cycle
Time
—
5
ms
—
21
—
Endurance
1M
—
E/W
Cycles
(Note 1)
(Note 2)
Note 1: This parameter is periodically sampled and not 100% tested.
2: This parameter is not tested but established by characterization. For endurance estimates in a specific application,
please consult the Total Endurance™ Model which can be obtained from Microchip’s web site at: www.microchip.com.
© 2008 Microchip Technology Inc.
DS21227F-page 3
25AA320/25LC320/25C320
FIGURE 1-1:
HOLD TIMING
CS
17
16
16
17
SCK
18
SO
n+2
n+1
n
19
High-Impedance
n
5
Don’t Care
n+2
SI
n+1
n-1
n
n
n-1
HOLD
FIGURE 1-2:
SERIAL INPUT TIMING
4
CS
12
2
7
Mode 1,1
11
8
3
SCK Mode 0,0
5
SI
6
MSB in
LSB in
High-Impedance
SO
FIGURE 1-3:
SERIAL OUTPUT TIMING
CS
9
3
10
Mode 1,1
SCK
Mode 0,0
13
14
SO
SI
DS21227F-page 4
MSB out
15
ISB out
Don’t Care
© 2008 Microchip Technology Inc.
25AA320/25LC320/25C320
TABLE 1-3:
AC TEST CONDITIONS
FIGURE 1-4:
AC Waveform:
AC TEST CIRCUIT
VCC
VLO = 0.2V
—
VHI = VCC - 0.2V
(Note 1)
VHI = 4.0V
(Note 2)
Timing Measurement Reference Level
Input
0.5 VCC
Output
0.5 VCC
2.25 KΩ
SO
1.8 KΩ
100 pF
Note 1: For VCC ≤ 4.0V
2: For VCC > 4.0V
© 2008 Microchip Technology Inc.
DS21227F-page 5
25AA320/25LC320/25C320
2.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 2-1.
TABLE 2-1:
2.1
PIN FUNCTION TABLE
Name
PDIP
SOIC
8-pin
TSSOP
14-lead
TSSOP
CS
1
1
3
1
Chip Select Input
Serial Data Output
SO
2
2
4
2
NC
—
—
—
3,4,5
WP
3
3
5
6
Write-Protect Pin
4
4
6
7
Ground
SI
5
5
7
8
Serial Data Input
SCK
6
6
8
9
NC
—
—
—
10,11,12
HOLD
7
7
1
13
Hold Input
Vcc
8
8
2
14
Supply Voltage
Chip Select (CS)
Serial Output (SO)
The SO pin is used to transfer data out of the 25XX320.
During a read cycle, data is shifted out on this pin after
the falling edge of the serial clock.
2.3
Not Connected
Vss
A low level on this pin selects the device. A high level
deselects the device and forces it into Standby mode.
However, a programming cycle which is already
initiated or in progress will be completed, regardless of
the CS input signal. If CS is brought high during a
program cycle, the device will go into Standby mode as
soon as the programming cycle is complete. When the
device is deselected, SO goes to the high-impedance
state, allowing multiple parts to share the same SPI
bus. A low-to-high transition on CS after a valid write
sequence initiates an internal write cycle. After powerup, a low level on CS is required prior to any sequence
being initiated.
2.2
Description
Write-Protect (WP)
This pin is used in conjunction with the WPEN bit in the
STATUS register to prohibit writes to the nonvolatile
bits in the STATUS register. When WP is low and
WPEN is high, writing to the nonvolatile bits in the STATUS register is disabled. All other operations function
normally. When WP is high, all functions, including
writes to the nonvolatile bits in the STATUS register
operate normally. If the WPEN bit is set, WP low during
a STATUS register write sequence will disable writing
to the STATUS register. If an internal write cycle has
already begun, WP going low will have no effect on the
write.
DS21227F-page 6
Serial Clock Input
Not Connected
The WP pin function is blocked when the WPEN bit in
the STATUS register is low. This allows the user to
install the 25XX320 in a system with WP pin grounded
and still be able to write to the STATUS register. The
WP pin functions will be enabled when the WPEN bit is
set high.
2.4
Serial Input (SI)
The SI pin is used to transfer data into the device. It
receives instructions, addresses, and data. Data is
latched on the rising edge of the serial clock.
2.5
Serial Clock (SCK)
The SCK is used to synchronize the communication
between a master and the 25XX320. Instructions,
addresses, or data present on the SI pin are latched on
the rising edge of the clock input, while data on the SO
pin is updated after the falling edge of the clock input.
2.6
Hold (HOLD)
The HOLD pin is used to suspend transmission to the
25XX320 while in the middle of a serial sequence without having to re-transmit the entire sequence again. It
must be held high any time this function is not being
used. Once the device is selected and a serial
sequence is underway, the HOLD pin may be pulled
low to pause further serial communication without
resetting the serial sequence. The HOLD pin must be
brought low while SCK is low, otherwise the HOLD
function will not be invoked until the next SCK high-tolow transition. The 25XX320 must remain selected during this sequence. The SI, SCK, and SO pins are in a
high-impedance state during the time the device is
paused and transitions on these pins will be ignored. To
resume serial communication, HOLD must be brought
high while the SCK pin is low, otherwise serial
communication will not resume. Lowering the HOLD
line at any time will tri-state the SO line.
© 2008 Microchip Technology Inc.
25AA320/25LC320/25C320
3.0
FUNCTIONAL DESCRIPTION
3.3
3.1
Principles Of Operation
Prior to any attempt to write data to the 25XX320, the
write enable latch must be set by issuing the WREN
instruction (Figure 3-4). This is done by setting CS low
and then clocking out the proper instruction into the
25XX320. After all eight bits of the instruction are
transmitted, the CS must be brought high to set the
write enable latch. If the write operation is initiated
immediately after the WREN instruction without CS
being brought high, the data will not be written to the
array because the write enable latch will not have been
properly set.
The 25XX320 are 4096 byte Serial EEPROMs
designed to interface directly with the Serial Peripheral
Interface (SPI) port of many of today’s popular
microcontroller
families,
including
Microchip’s
PIC16C6X/7X microcontrollers. It may also interface
with microcontrollers that do not have a built-in SPI port
by using discrete I/O lines programmed properly with
the software.
The 25XX320 contains an 8-bit instruction register. The
device is accessed via the SI pin, with data being
clocked in on the rising edge of SCK. The CS pin must
be low and the HOLD pin must be high for the entire
operation.
Table 3-1 contains a list of the possible instruction
bytes and format for device operation. All instructions,
addresses and data are transferred MSB first, LSB last.
Data is sampled on the first rising edge of SCK after CS
goes low. If the clock line is shared with other
peripheral devices on the SPI bus, the user can assert
the HOLD input and place the 25XX320 in ‘HOLD’
mode. After releasing the HOLD pin, operation will
resume from the point when the HOLD was asserted.
3.2
Read Sequence
The device is selected by pulling CS low. The 8-bit
READ instruction is transmitted to the 25XX320 followed by the 16-bit address, with the four MSBs of the
address being “don’t care” bits. After the correct READ
instruction and address are sent, the data stored in the
memory at the selected address is shifted out on the
SO pin. The data stored in the memory at the next
address can be read sequentially by continuing to provide clock pulses. The internal Address Pointer is automatically incremented to the next higher address after
each byte of data is shifted out. When the highest
address is reached (0FFFh), the address counter rolls
over to address 0000h allowing the read cycle to be
continued indefinitely. The read operation is terminated
by raising the CS pin (Figure 3-1).
TABLE 3-1:
Write Sequence
Once the write enable latch is set, the user may
proceed by setting the CS low, issuing a WRITE
instruction, followed by the 16-bit address, with the four
MSBs of the address being “don’t care” bits, and then
the data to be written. Up to 32 bytes of data can be
sent to the 25XX320 before a write cycle is necessary.
The only restriction is that all of the bytes must reside
in the same page. A page address begins with xxxx
xxxx xxx0 0000 and ends with xxxx xxxx xxx1
1111. If the internal address counter reaches xxxx
xxxx xxx1 1111 and the clock continues, the counter
will roll back to the first address of the page and overwrite any data in the page that may have been written.
For the data to be actually written to the array, the CS
must be brought high after the Least Significant bit (D0)
of the nth data byte has been clocked in. If CS is
brought high at any other time, the write operation will
not be completed. Refer to Figure 3-2 and Figure 3-3
for more detailed illustrations on the byte write
sequence and the page write sequence, respectively.
While the write is in progress, the STATUS register may
be read to check the status of the WPEN, WIP, WEL,
BP1 and BP0 bits (Figure 3-6). A read attempt of a
memory array location will not be possible during a
write cycle. When the write cycle is completed, the
write enable latch is reset.
INSTRUCTION SET
Instruction Name
Instruction Format
Description
READ
0000 0011
Read data from memory array beginning at selected address
WRITE
0000 0010
Write data to memory array beginning at selected address
WRDI
0000 0100
Reset the write enable latch (disable write operations)
WREN
0000 0110
Set the write enable latch (enable write operations)
RDSR
0000 0101
Read STATUS register
WRSR
0000 0001
Write STATUS register
© 2008 Microchip Technology Inc.
DS21227F-page 7
25AA320/25LC320/25C320
FIGURE 3-1:
READ SEQUENCE
CS
0
1
2
3
4
5
6
7
8
9 10 11
21 22 23 24 25 26 27 28 29 30 31
SCK
Instruction
0
SI
0
0
0
0
16-bit Address
0
1 15 14 13 12
1
2
1
0
Data Out
High-Impedance
7
SO
FIGURE 3-2:
6
5
4
3
2
1
0
BYTE WRITE SEQUENCE
CS
Twc
0
1
2
0
0
0
3
4
5
6
7
8
9 10 11
0
1
0 15 14 13 12
21 22 23 24 25 26 27 28 29 30 31
SCK
Instruction
SI
0
0
16-bit Address
Data Byte
2
1
0
7
6
5
4
3
2
1
0
High-Impedance
SO
FIGURE 3-3:
PAGE WRITE SEQUENCE
CS
0
1
2
3
4
5
6
7
8
9 10 11
21 22 23 24 25 26 27 28 29 30 31
SCK
Instruction
SI
0
0
0
0
0
16-bit Address
0 1
Data Byte 1
2
0 15 14 13 12
1
0
7
6
5
4
3
2
1
0
CS
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
SCK
Data Byte 2
SI
7
DS21227F-page 8
6
5
4
3
2
Data Byte 3
1
0
7
6
5
4
3
2
Data Byte n (32 max)
1
0
7
6
5
4
3
2
1
0
© 2008 Microchip Technology Inc.
25AA320/25LC320/25C320
3.4
Write Enable (WREN) and Write
Disable (WRDI)
The following is a list of conditions under which the
write enable latch will be reset:
•
•
•
•
The 25XX320 contains a write enable latch.
See
Table 3-3 for the Write-Protect Functionality Matrix.
This latch must be set before any write operation will be
completed internally. The WREN instruction will set the
latch, and the WRDI will reset the latch.
FIGURE 3-4:
Power-up
WRDI instruction successfully executed
WRSR instruction successfully executed
WRITE instruction successfully executed
WRITE ENABLE SEQUENCE
CS
0
1
2
3
4
5
6
7
SCK
SI
0
0
0
0
0
1
1
0
High-Impedance
SO
FIGURE 3-5:
WRITE DISABLE SEQUENCE
CS
0
1
2
3
4
5
6
7
SCK
SI
0
0
0
0
0
1
10
0
High-Impedance
SO
© 2008 Microchip Technology Inc.
DS21227F-page 9
25AA320/25LC320/25C320
3.5
Read Status Register Instruction
(RDSR)
The Write Enable Latch (WEL) bit indicates the status
of the write enable latch. When set to a ‘1’, the latch
allows writes to the array, when set to a ‘0’, the latch
prohibits writes to the array. The state of this bit can
always be updated via the WREN or WRDI commands
regardless of the state of write protection on the STATUS register. This bit is read-only.
The Read Status Register instruction (RDSR) provides
access to the STATUS register. The STATUS register
may be read at any time, even during a write cycle. The
STATUS register is formatted as follows:
7
6
5
4
3
2
1
0
WPEN
X
X
X
BP1
BP0
WEL
WIP
The Block Protection (BP0 and BP1) bits indicate
which blocks are currently write-protected. These bits
are set by the user issuing the WRSR instruction. These
bits are nonvolatile.
The Write-In-Process (WIP) bit indicates whether the
25XX320 is busy with a write operation. When set to a
‘1’, a write is in progress; when set to a ‘0’, no write is
in progress. This bit is read-only.
FIGURE 3-6:
See Figure 3-6 for the RDSR timing sequence.
READ STATUS REGISTER TIMING SEQUENCE
CS
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
SCK
Instruction
SI
0
0
0
0
0
1
0
1
Data from STATUS Register
High-Impedance
SO
DS21227F-page 10
7
6
5
4
3
2
1
0
© 2008 Microchip Technology Inc.
25AA320/25LC320/25C320
3.6
Write Status Register Instruction
(WRSR)
When the chip is hardware write-protected, only writes
to nonvolatile bits in the STATUS register are disabled.
See Table 3-3 for a matrix of functionality on the WPEN
bit.
The Write Status Register instruction (WRSR) allows the
user to select one of four levels of protection for the
array by writing to the appropriate bits in the STATUS
register. The array is divided up into four segments.
The user has the ability to write-protect none, one, two,
or all four of the segments of the array. The partitioning
is controlled as shown in Table 3-2.
See Figure 3-7 for the WRSR timing sequence.
TABLE 3-2:
The Write-Protect Enable (WPEN) bit is a nonvolatile
bit that is available as an enable bit for the WP pin. The
Write-Protect (WP) pin and the Write-Protect Enable
(WPEN) bit in the STATUS register control the programmable hardware write-protect feature. Hardware
write protection is enabled when WP pin is low and the
WPEN bit is high. Hardware write protection is disabled
when either the WP pin is high or the WPEN bit is low.
FIGURE 3-7:
ARRAY PROTECTION
BP1
BP0
Array Addresses
Write-Protected
0
0
none
0
1
upper 1/4
(0C00h-0FFFh)
1
0
upper 1/2
(0800h-0FFFh)
1
1
all
(0000h-0FFFh)
WRITE STATUS REGISTER TIMING SEQUENCE
CS
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
SCK
Instruction
SI
0
0
0
0
0
Data to STATUS Register
0
0
1
7
6
5
4
3
2
1
0
High-Impedance
SO
© 2008 Microchip Technology Inc.
DS21227F-page 11
25AA320/25LC320/25C320
3.7
Data Protection
3.8
The following protection has been implemented to
prevent inadvertent writes to the array:
• The write enable latch is reset on power-up
• A WRITE ENABLE instruction must be issued to
set the write enable latch
• After a byte write, page write or STATUS register
write, the write enable latch is reset
• CS must be set high after the proper number of
clock cycles to start an internal write cycle
• Access to the array during an internal write cycle
is ignored and programming is continued
Power-On State
The 25XX320 powers on in the following state:
• The device is in low-power Standby mode
(CS = 1)
• The write enable latch is reset
• SO is in high-impedance state
• A low level on CS is required to enter active state
.
TABLE 3-3:
WRITE-PROTECT FUNCTIONALITY MATRIX
WPEN
WP
WEL
Protected Blocks
Unprotected Blocks
STATUS Register
x
x
0
Protected
Protected
Protected
Writable
Writable
0
x
1
Protected
1
Low
1
Protected
Writable
Protected
x
High
1
Protected
Writable
Writable
DS21227F-page 12
© 2008 Microchip Technology Inc.
25AA320/25LC320/25C320
4.0
PACKAGING INFORMATION
4.1
Package Marking Information
8-Lead PDIP (300 mil)
XXXXXXXX
XXXXXNNN
YYWW
Example:
25LC320
/PNNN
YYWW
8-Lead SOIC (150 mil)
XXXXXXXX
XXXXYYWW
NNN
Example:
25LC320
I/SN e3 YYWW
NNN
Example:
8-Lead TSSOP
XXXX
XYWW
NNN
Example:
14-Lead TSSOP
XXXXXXXX
YYWW
NNN
Legend: XX...X
Y
YY
WW
NNN
e3
*
Note:
*
5LBX
IYWW
NNN
25L32
YYWW
NNN
Customer-specific information
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
Pb-free JEDEC designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator ( e3 )
can be found on the outer packaging for this package.
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
Standard marking consists of Microchip part number, year code, week code, and traceability code. For
device markings beyond this, certain price adders apply. Please check with your Microchip Sales Office.
For QTP devices, any special marking adders are included in QTP price.
© 2008 Microchip Technology Inc.
DS21227F-page 13
25AA320/25LC320/25C320
3
&'
!&"&4#*!(!!&
4%&
&#&
&&255***'
'54
N
NOTE 1
E1
1
3
2
D
E
A2
A
L
A1
c
e
eB
b1
b
6&!
'!
9'&!
7"')
%!
7,8.
7
7
7:
;
<
&
&
&
=
=
##44!!
-
1!&
&
=
=
"#&
"#>#&
.
-
-
##4>#&
.
<
: 9&
-<
-?
&
&
9
-
9#4!!
<
)
?
)
<
1
=
=
69#>#&
9
*9#>#&
: *+
1,
-
!"#$%&"' ()"&'"!&)
&#*&&&#
+%&,&!&
- '!
!#.#
&"#'
#%!
&"!
!
#%!
&"!
!!
&$#/!#
'!
#&
.0
1,21!'!
&$& "!
**&
"&&
!
* ,<1
DS21227F-page 14
© 2008 Microchip Technology Inc.
25AA320/25LC320/25C320
!
""#$%& !'
3
&'
!&"&4#*!(!!&
4%&
&#&
&&255***'
'54
D
e
N
E
E1
NOTE 1
1
2
3
α
h
b
h
A2
A
c
φ
L
A1
L1
6&!
'!
9'&!
7"')
%!
β
99..
7
7
7:
;
<
&
: 8&
=
1,
=
##44!!
=
=
&#
%%+
=
: >#&
.
##4>#&
.
-1,
: 9&
1,
?1,
,'%@
&
A
=
3
&9&
9
=
3
&&
9
.3
3
&
I
B
=
<B
9#4!!
=
9#>#&
)
-
=
#%&
D
B
=
B
#%&1
&&
'
E
B
=
B
!"#$%&"' ()"&'"!&)
&#*&&&#
+%&,&!&
- '!
!#.#
&"#'
#%!
&"!
!
#%!
&"!
!!
&$#''!#
'!
#&
.0
1,2 1!'!
&$& "!
**&
"&&
!
.32 %'!
("!"*&
"&&
(%
%
'&
"
!!
* ,1
© 2008 Microchip Technology Inc.
DS21227F-page 15
25AA320/25LC320/25C320
!
""#$%& !'
3
&'
!&"&4#*!(!!&
4%&
&#&
&&255***'
'54
DS21227F-page 16
© 2008 Microchip Technology Inc.
25AA320/25LC320/25C320
() )"* !
(+%+(
!
3
&'
!&"&4#*!(!!&
4%&
&#&
&&255***'
'54
D
N
E
E1
NOTE 1
1
2
b
e
c
A
φ
A2
A1
L
L1
6&!
'!
9'&!
7"')
%!
99..
7
7
7:
;
<
&
: 8&
=
?1,
=
##44!!
<
&#
%%
=
: >#&
.
##4>#&
.
-
?1,
##49&
-
-
3
&9&
9
?
3
&&
9
.3
3
&
I
B
=
<B
9#4!!
=
9#>#&
)
=
-
!"#$%&"' ()"&'"!&)
&#*&&&#
'!
!#.#
&"#'
#%!
&"!
!
#%!
&"!
!!
&$#''!#
- '!
#&
.0
1,2 1!'!
&$& "!
**&
"&&
!
.32 %'!
("!"*&
"&&
(%
%
'&
"
!!
* ,<?1
© 2008 Microchip Technology Inc.
DS21227F-page 17
25AA320/25LC320/25C320
,+
() )"* !
(+%+(
!
3
&'
!&"&4#*!(!!&
4%&
&#&
&&255***'
'54
D
N
E
E1
NOTE 1
1 2
e
b
A2
A
c
A1
φ
6&!
'!
9'&!
7"')
%!
L
L1
99..
7
7
7:
;
&
: 8&
=
?1,
=
##44!!
<
&#
%%
=
: >#&
.
##4>#&
.
-
?1,
##49&
3
&9&
9
?
3
&&
9
.3
3
&
B
=
<B
9#4!!
=
9#>#&
)
=
-
!"#$%&"' ()"&'"!&)
&#*&&&#
'!
!#.#
&"#'
#%!
&"!
!
#%!
&"!
!!
&$#''!#
- '!
#&
.0
1,2 1!'!
&$& "!
**&
"&&
!
.32 %'!
("!"*&
"&&
(%
%
'&
"
!!
* ,<1
DS21227F-page 18
© 2008 Microchip Technology Inc.
25AA320/25LC320/25C320
APPENDIX A:
REVISION HISTORY
Revision D
Corrections to Section 1.0, Electrical Characteristics.
Revision E
Revise Endurance from 100K to 1M.
Revision F (June 2008)
Added “Not Recommended” note; Updated Packaging;
General updates.
© 2008 Microchip Technology Inc.
DS21227F-page 19
25AA320/25LC320/25C320
NOTES:
DS21227F-page 20
© 2008 Microchip Technology Inc.
25AA320/25LC320/25C320
THE MICROCHIP WEB SITE
CUSTOMER SUPPORT
Microchip provides online support via our WWW site at
www.microchip.com. This web site is used as a means
to make files and information easily available to
customers. Accessible by using your favorite Internet
browser, the web site contains the following
information:
Users of Microchip products can receive assistance
through several channels:
• Product Support – Data sheets and errata,
application notes and sample programs, design
resources, user’s guides and hardware support
documents, latest software releases and archived
software
• General Technical Support – Frequently Asked
Questions (FAQ), technical support requests,
online discussion groups, Microchip consultant
program member listing
• Business of Microchip – Product selector and
ordering guides, latest Microchip press releases,
listing of seminars and events, listings of
Microchip sales offices, distributors and factory
representatives
•
•
•
•
•
Distributor or Representative
Local Sales Office
Field Application Engineer (FAE)
Technical Support
Development Systems Information Line
Customers
should
contact
their
distributor,
representative or field application engineer (FAE) for
support. Local sales offices are also available to help
customers. A listing of sales offices and locations is
included in the back of this document.
Technical support is available through the web site
at: http://support.microchip.com
CUSTOMER CHANGE NOTIFICATION
SERVICE
Microchip’s customer notification service helps keep
customers current on Microchip products. Subscribers
will receive e-mail notification whenever there are
changes, updates, revisions or errata related to a
specified product family or development tool of interest.
To register, access the Microchip web site at
www.microchip.com, click on Customer Change
Notification and follow the registration instructions.
© 2008 Microchip Technology Inc.
DS21227F-page 21
25AA320/25LC320/25C320
READER RESPONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation
can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150.
Please list the following information, and use this outline to provide us with your comments about this document.
To:
Technical Publications Manager
RE:
Reader Response
Total Pages Sent ________
From: Name
Company
Address
City / State / ZIP / Country
Telephone: (_______) _________ - _________
FAX: (______) _________ - _________
Application (optional):
Would you like a reply?
Y
N
Device: 25AA320/25LC320/25C320
Literature Number: DS21227F
Questions:
1. What are the best features of this document?
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this document easy to follow? If not, why?
4. What additions to the document do you think would enhance the structure and subject?
5. What deletions from the document could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
DS21227F-page 22
© 2008 Microchip Technology Inc.
25AA320/25LC320/25C320
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
X
/XX
XXX
Device
Temperature
Range
Package
Pattern
Examples:
a)
b)
Device:
25AA320:
25AA320T:
25AA320X
25AA320XT
25LC320:
25LC320T:
25LC320X
25LC320XT
25C320:
25C320T:
25C320X
25C320XT
32 Kbit 1.8V SPI Serial EEPROM
32 Kbit 1.8V SPI Serial EEPROM
(Tape and Reel)
32-bit 1.8V SPI Serial EEPROM
in alternate pinout (ST only)
32-bit 1.8V SPI Serial EEPROM
in alternate pinout Tape and Reel
(ST only)
32 Kbit 2.5V SPI Serial EEPROM
32 Kbit 2.5V SPI Serial EEPROM
(Tape and Reel)
32-bit 2.5V SPI Serial EEPROM
in alternate pinout (ST only)
32-bit 2.5V SPI Serial EEPROM
in alternate pinout Tape and Reel
(ST only)
32 Kbit 5V SPI Serial EEPROM
32 Kbit 5V SPI Serial EEPROM
(Tape and Reel)
32-bit 5V SPI Serial EEPROM
in alternate pinout (ST only)
32-bit 5V SPI Serial EEPROM
in alternate pinout Tape and Reel
(ST only)
Temperature
Range:
I
E
=
=
-40°C to +85°C
-40°C to +125°C
Package:
P
SN
=
=
ST
=
Plastic DIP (300 mil body), 8-lead
Plastic SOIC (150 mil body),
8-lead
Plastic TSSOP (4.4 mm body),
8-lead
Plastic TSSOP (4.4 mm body),
14-lead
ST14 =
© 2008 Microchip Technology Inc.
c)
d)
e)
f)
g)
25LC320-I/SN: Industrial Temp.,
SOIC package
25LC320T-I/SN: Tape and Reel,
Industrial Temp., SOIC package
25LC320-E/SN: Extended Temp.,
SOIC package
25C320-I/SN: Industrial Temp.,
SOIC package
25C320T-I/SN: Tape and Reel,
Industrial Temp., SOIC package
25C320-I/ST: Industrial Temp.,
TSSOP package
25C320-E/SN: Extended Temp.,
SOIC package
DS21227F-page 23
25AA320/25LC320/25C320
NOTES:
DS21227F-page 24
© 2008 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, Accuron,
dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro,
PICSTART, PRO MATE, rfPIC and SmartShunt are registered
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
FilterLab, Linear Active Thermistor, MXDEV, MXLAB,
SEEVAL, SmartSensor and The Embedded Control Solutions
Company are registered trademarks of Microchip Technology
Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, CodeGuard,
dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,
ECONOMONITOR, FanSense, In-Circuit Serial
Programming, ICSP, ICEPIC, Mindi, MiWi, MPASM, MPLAB
Certified logo, MPLIB, MPLINK, mTouch, PICkit, PICDEM,
PICDEM.net, PICtail, PIC32 logo, PowerCal, PowerInfo,
PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Total
Endurance, UNI/O, WiperLock and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2008, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
Microchip received ISO/TS-16949:2002 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
© 2008 Microchip Technology Inc.
DS21227F-page 25
WORLDWIDE SALES AND SERVICE
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://support.microchip.com
Web Address:
www.microchip.com
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-4182-8400
Fax: 91-80-4182-8422
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Kokomo
Kokomo, IN
Tel: 765-864-8360
Fax: 765-864-8387
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8528-2100
Fax: 86-10-8528-2104
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
Taiwan - Hsin Chu
Tel: 886-3-572-9526
Fax: 886-3-572-6459
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-536-4803
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
01/02/08
DS21227F-page 26
© 2008 Microchip Technology Inc.