MAXIM MAX4698EBT

19-1994; Rev 3; 2/03
35Ω, Low-Voltage, SPST/SPDT
Analog Switches in UCSP Package
Features
♦ 6-Bump, 0.5mm Pitch, UCSP
♦ RON
35Ω max (+3V Supply)
20Ω max (+5V Supply)
♦ 2Ω max RON Match Between Channels
♦ 13Ω max RON Flatness Over Signal Range
♦ Low Leakage Currents Over Temperature
1nA (max) at TA = +25°C
♦ Fast Switching: tON = 80ns, tOFF = 25ns
♦ Guaranteed Break-Before-Make (MAX4698)
♦ +2.0V to +5.5V Single-Supply Operation
♦ Rail-to-Rail® Signal Handling
♦ Low Crosstalk: -75dB (100kHz)
♦ High Off-Isolation: -75dB (100kHz)
♦ 1.8V CMOS Logic Compatible
♦ -3dB Bandwidth: >200MHz
________________________Applications
MP3 Players
Battery-Operated Equipment
Relay Replacement
Audio and Video Signal Routing
Communications Circuits
PCMCIA Cards
Cellular Phones
Hard Drives
Modems
Ordering Information
TEMP
RANGE
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
PART
MAX4696EBT-T
MAX4697EBT-T
MAX4698EBT-T
PIN/BUMPPACKAGE
6 UCSP
6 UCSP
6 UCSP
TOP
MARK
AAL
AAM
AAN
Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd.
UCSP is a trademark of Maxim Integrated Products, Inc.
Pin Configurations/Functional Diagrams/Truth Table
TOP VIEW
V+
B1
A1
NO
IN
B2
A2
COM
GND
B3
A3
MAX4696
COM
V+
B1
A1
NC
V+
B1
A1
NO
IN
B2
A2
COM
IN
B2
A2
COM
GND
B3
A3
COM
MAX4697
GND
B3
A3
NC
IN
NO
0
OFF
ON
1
ON
OFF
NC
MAX4698
SWITCHES SHOWN FOR LOGIC "0"
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX4696/MAX4697/MAX4698
General Description
The MAX4696/MAX4697/MAX4698 low on-resistance
(RON), low-voltage analog switches operate from a single +2.0V to +5.5V supply. The MAX4696/MAX4697 are
single-pole/single-throw (SPST) analog switches, and
the MAX4698 is a single-pole/double-throw (SPDT) analog switch. The MAX4696 is a normally open (NO)
switch, and the MAX4697 is a normally closed (NC)
switch.
When powered from a 2.7V supply, these devices feature
35Ω (max) RON, with 2Ω (max) RON matching and 13Ω
(max) flatness. The MAX4696/MAX4697/MAX4698 offer
fast switching speeds (tON = 80ns max, tOFF = 25ns
max). The MAX4698 offers a break-before-make function.
The digital logic inputs are 1.8V logic compatible from a
+2.7V to +3.3V supply and are TTL/CMOS compatible
from a +4.5V to +5.5V supply. The MAX4696/MAX4697/
MAX4698 are packaged in the chip-scale package
(UCSP™), significantly reducing the required PC board
area. The device occupies only a 1.50mm ✕ 1.02mm
area. The 3 ✕ 2 array of solder bumps are spaced with
a 0.5mm bump pitch.
MAX4696/MAX4697/MAX4698
35Ω, Low-Voltage, SPST/SPDT
Analog Switches in UCSP Package
ABSOLUTE MAXIMUM RATINGS
All Voltages Referenced to GND
V+, IN .......................................................................-0.3V to +6V
COM, NO, NC (Note 1).................................-0.3V to (V+ + 0.3V)
Continuous Current COM, NO, NC ..................................±20mA
Peak Current COM, NO, NC
(pulsed at 1ms, 10% duty cycle) .................................±40mA
Continuous Power Dissipation (TA = +70°C)
3 ✕ 2 UCSP (derate 10.1mW/°C at +70°C)....................808mW
Operating Temperature Range ...........................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Bump Temperature (soldering)
Infrared (15s) ................................................................+220°C
Vapor Phase (60s) ........................................................+215°C
Note 1: Signals on NO, NC, and COM exceeding V+ are clamped by an internal diode. Limit forward-diode current to maximum current rating.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS—Single +3V Supply
(V+ = +2.7V to +3.3V, VIH = +1.4V, VIL = 0.5V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at +3V and
TA = +25°C.) (Notes 2, 8)
PARAMETER
SYMBOL
CONDITIONS
TA
MIN
TMIN to TMAX
0
TYP
MAX
UNITS
V+
V
ANALOG SWITCH
Analog Signal Range
VCOM, VNO,
VNC
RON
V+ = +2.7V, ICOM = 1mA,
VNO or VNC = 1.5V
On-Resistance Match
Between Channels
(MAX4698 only) (Note 4)
∆RON
V+ = +2.7V, ICOM = 1mA,
VNO or VNC = 1.5V
TMIN to TMAX
On-Resistance Flatness
(Note 5)
RFLAT(ON)
V+ = +2.7V, ICOM = 1mA,
VNO or VNC = 1V, 1.5V, 2V
TMIN to TMAX
NO, NC Off-Leakage
Current (Note 3)
INO(OFF),
INC(OFF)
V+ = +3.6V; VCOM = 0.3V,
3.3V; VNO or VNC = 3.3V, 0.3V
+25°C
-0.5
TMIN to TMAX
-1
COM Off-Leakage Current
(Note 3)
(MAX4696, MAX4697 only)
V+ = +3.6V; VCOM = 0.3V,
3.3V; VNO or VNC = 0.3V, 3.3V
+25°C
-0.5
ICOM_(OFF)
TMIN to TMAX
-1
COM On-Leakage Current
(Note 3)
V+ = +3.6V; VCOM = 0.3V,
3.3V; VNO or VNC = 0.3V, 3.3V,
or floating
+25°C
-0.5
ICOM_(ON)
TMIN to TMAX
-2
On-Resistance
+25°C
30
TMIN to TMAX
35
40
+25°C
1
2
3
+25°C
10
13
15
±0.01
0.5
1
±0.01
Ω
Ω
Ω
nA
0.5
nA
1
±0.01
0.5
nA
2
DYNAMIC CHARACTERISTICS
Turn-On Time (Note 3)
2
tON
V+ = +2.7V; VNO, VNC = 1.5V,
RL = 300Ω, CL = 35pF,
Figure 1
+25°C
50
80
ns
TMIN to TMAX
_______________________________________________________________________________________
110
35Ω, Low-Voltage, SPST/SPDT
Analog Switches in UCSP Package
(V+ = +2.7V to +3.3V, VIH = +1.4V, VIL = 0.5V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at +3V and
TA = +25°C.) (Notes 2, 8)
PARAMETER
SYMBOL
CONDITIONS
TA
+25°C
Turn-Off Time (Note 3)
tOFF
V+ = +2.7V; VNO, VNC = 1.5V,
RL = 300Ω, CL = 35pF,
Figure 1
Break-Before-Make Time
(MAX4698 only) (Note 3)
tBBM
V+ = +3.3V; VNO, VNC = 1.5V,
Figure 2
MIN
TYP
MAX
20
25
TMIN to TMAX
40
+25°C
15
TMIN to TMAX
UNITS
ns
ns
2
VGEN = 0, RGEN = 0,
CL = 1.0nF, Figure 3
+25°C
8
pC
BW
Signal = 0dBm, 50Ω in and out,
Figure 4
+25°C
200
MHz
Off-Isolation (Note 6)
VISO
f = 100kHz, RL = 50Ω,
CL = 5pF, Figure 4
+25°C
-75
dB
Crosstalk (MAX4698 only)
(Note 7)
VCT
f = 100kHz, RL = 50Ω,
CL = 5pF, Figure 4
+25°C
-75
dB
Total Harmonic Distortion
THD
f = 20Hz to 20kHz,
2Vp-p, RL = 600Ω
+25°C
0.014
%
NO, NC
Off-Capacitance
CNO(OFF),
CNC(OFF)
f = 1MHz, Figure 5
+25°C
15
pF
COM Off-Capacitance
CCOM(OFF) f = 1MHz, Figure 5
+25°C
15
pF
+25°C
30
pF
Charge Injection
Q
On-Channel -3dB
Bandwidth
Switch On-Capacitance
C(ON)
f = 1MHz, Figure 6
DIGITAL I/O
Input Logic High
VIH
Input Logic Low
VIL
Input Leakage Current
IIN
TMIN to TMAX
1.4
V
0.5
V
VIN = 0 or V+
TMIN to TMAX
TMIN to TMAX
-1
1
µA
TMIN to TMAX
2.0
5.5
V
V+ = +3.3V, VIN = 0 or V+
TMIN to TMAX
1
µA
POWER SUPPLY
Power-Supply Range
V+
Supply Current
I+
ELECTRICAL CHARACTERISTICS—Single +5V Supply
(V+ = +4.5V to +5.5V, VIH = +2.4V, VIL = 0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at +5V and
TA = +25°C.) (Notes 2, 8)
PARAMETER
SYMBOL
CONDITIONS
TA
MIN
TYP
MAX
UNITS
V+
V
ANALOG SWITCH
Analog Signal Range
On-Resistance
VCOM,
VNO, VNC
RON
On-Resistance Match
(MAX4698 only)
(Note 4)
∆RON
0
V+ = +4.5V, ICOM = 1mA,
VNO or VNC = 1V, 3.5V
V+ = 4.5V, ICOM = 1mA,
VNO or VNC = 1V, 3.5V
+25°C
15
TMIN to TMAX
+25°C
TMIN to TMAX
20
25
1
Ω
3
4
Ω
_______________________________________________________________________________________
3
MAX4696/MAX4697/MAX4698
ELECTRICAL CHARACTERISTICS—Single +3V Supply (continued)
MAX4696/MAX4697/MAX4698
35Ω, Low-Voltage, SPST/SPDT
Analog Switches in UCSP Package
ELECTRICAL CHARACTERISTICS—Single +5V Supply (continued)
(V+ = +4.5V to +5.5V, VIH = +2.4V, VIL = 0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at +5V and
TA = 25°C.) (Notes 2, 8)
PARAMETER
SYMBOL
CONDITIONS
TA
MIN
+25°C
On-Resistance Flatness
(Note 5)
RFLAT(ON)
V+ = +4.5V, ICOM = 1mA,
VNO or VNC = 1V, 2.25V, 3.5V
TMIN to TMAX
NO, NC Off-Leakage
Current (Note 3)
INO(OFF),
INC(OFF)
V+ = +5.5V; VCOM = 1V, 4.5V;
VNO or VNC = 4.5V, 1V
+25°C
-0.5
TMIN to TMAX
-1
+25°C
-0.5
TMIN to TMAX
-1
+25°C
-0.5
TMIN to TMAX
-2
COM Off-Leakage Current
V+ = +5.5V; VCOM = 1V, 4.5V;
(MAX4696, MAX4697 only) ICOM_(OFF)
VNO or VNC = 4.5V, 1V
(Note 3)
COM On-Leakage Current
(Note 3)
Turn-On Time (Note 3)
Turn-Off Time (Note 3)
Break-Before-Make Time
(MAX4698 only) (Note 3)
V+ = +5.5V; VCOM = 1V, 4.5V;
ICOM_(ON) VNO or VNC = 1V, 4.5V, or
floating
tON
V+ = +5.5V, VNO, VNC = 3V,
RL = 300Ω, CL = 35pF,
Figure 1
tOFF
V+ = +5.5V, VNO, VNC = 3V,
RL = 300Ω, CL = 35pF,
Figure 1
tBBM
V+ = +5.5V, VNO, VNC = 3V,
RL = 300Ω, CL = 35pF,
Figure 2
TYP
MAX
3
4
5
±0.01
0.5
1
±0.01
UNITS
Ω
nA
0.5
nA
1
±0.01
0.5
nA
+25°C
2
30
40
ns
TMIN to TMAX
50
+25°C
15
20
ns
TMIN to TMAX
25
+25°C
9
ns
TMIN to TMAX
2
DIGITAL I/O
Input Logic High
VIH
Input Logic Low
VIL
Input Leakage Current
IIN
2.4
VIN = 0 or V+
V
0.8
V
-1
1
µA
2.0
5.5
V
1
µA
SUPPLY
Power-Supply Range
V+
Supply Current
I+
V+ = +5.5V, VIN = 0 or V+
Note 2: The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in
this data sheet.
Note 3: Guaranteed by design.
Note 4: ∆RON = RON(MAX) - RON(MIN), between switches.
Note 5: Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the
specified analog signal ranges.
Note 6: Off-Isolation = 20log10 (VCOM / VNO), VCOM = output, VNO = input to off switch.
Note 7: Between switches.
Note 8: UCSP parts are 100% tested at +25°C only, and guaranteed by correlation at the full-rated temperature.
4
_______________________________________________________________________________________
35Ω, Low-Voltage, SPST/SPDT
Analog Switches in UCSP Package
25
RON (Ω)
40
20
RON (Ω)
V+ = +2.7V
30
V+ = +3.3V
V+ = +5V
TA = +85°C
16
14
12
TA = +25°C
15
TA = -40°C
10
MAX4696/7/8 toc03
V+ = +2V
TA = +85°C
RON (Ω)
50
18
MAX4696/7/8 toc02
30
MAX4696/7/8 toc01
60
20
ON-RESISTANCE vs.
VCOM (V+ = +5V)
ON-RESISTANCE vs.
VCOM (V+ = +3V)
ON-RESISTANCE vs. VCOM
10
TA = +25°C
8
6
TA = -40°C
4
10
5
0
0
2
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
0
0
0.5
1.0
1.5
VCOM (V)
0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
3.0
VCOM (V)
TURN-ON/OFF TIME vs.
SUPPLY VOLTAGE
CHARGE INJECTION vs. VCOM
10
OFF-LEAKAGE
1
25
60
50
20
V+ = +3V
15
10
0
20
40
60
4.5
5.5
TURN-ON/OFF TIME vs.
TEMPERATURE
SUPPLY CURRENT vs.
SUPPLY VOLTAGE
LOGIC THRESHOLD VOLTAGE vs.
SUPPLY VOLTAGE
tON
V+ = +5V
50
tOFF
V+ = +3V
20
70
VIN = GND
65
60
55
50
45
40
35
30
10
tOFF
V+ = +5V
0
20
40
TEMPERATURE (°C)
60
80
1.2
VIN RISING
1.0
0.8
VIN FALLING
0.6
0.4
0.2
25
0
20
0
1.4
LOGIC THRESHOLD VOLTAGE (V)
MAX4696/7/8 toc07
tON
V+ = +3V
-20
3.5
2.5
V+ (V)
60
-40
1.5
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
VCOM (V)
70
30
0
TEMPERATURE (°C)
80
40
tOFF
0
0
80
30
10
MAX4696/7/8 toc08
-20
SUPPLY CURRENT (pA)
-40
tON
40
20
V+ = +5V
5
0.1
MAX4696/7/8 toc06
70
tON/OFF (ns)
100
30
MAX4696/7/8 toc05
ON-LEAKAGE
CHARGE INJECTION (pC)
MAX 4696/7/8 toc04
1000
ON/OFF-LEAKAGE CURRENTS (pA)
2.5
VCOM (V)
ON/OFF-LEAKAGE CURRENT vs.
TEMPERATURE
tON/OFF (ns)
2.0
MAX4696/7/8 toc09
0
0
1
2
3
4
SUPPLY VOLTAGE (V)
5
6
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
V+ (V)
_______________________________________________________________________________________
5
MAX4696/MAX4697/MAX4698
Typical Operating Characteristics
(TA = +25°C, unless otherwise noted.)
Typical Operating Characteristics (continued)
(TA = +25°C, unless otherwise noted.)
TOTAL HARMONIC
DISTORTION vs. FREQUENCY
FREQUENCY RESPONSE
0
-20
MAX4696/7/8 toc11
0.1
MAX4696/7/8 toc10
20
RL = 600Ω
V+ = +5V
VCOM = 2VP-P
f = 20kHz
ON-LOSS
THD (%)
LOSS (dB)
MAX4696/MAX4697/MAX4698
35Ω, Low-Voltage, SPST/SPDT
Analog Switches in UCSP Package
-40
-60
-80
0.01
OFF-ISOLATION
-100
0.001
-120
10k
100k
1M
10M
100M
10
1G
FREQUENCY (Hz)
100
10k
1k
FREQUENCY (Hz)
100k
Pin/Bump Description
PIN/BUMP
FUNCTION
MAX4697
MAX4698
B1
B1
B1
V+
Positive Supply Voltage Input
B2
B2
B2
IN
Digital Control Input
B3
B3
B3
GND
—
A1
A3
NC
A2, A3
A2, A3
A2
COM
A1
—
A1
NO
Applications Information
Logic Inputs
Where the MAX4696/MAX4697/MAX4698 have a +3.3V
supply, IN may be driven low to GND and driven high
to 5.5V. Driving IN rail-to-rail minimizes power consumption. Logic inputs accept up to +5.5V regardless
of supply voltage.
Analog Signal Levels
Analog signals that range over the entire supply voltage (GND to V+) are passed with very little change in
R ON (see Typical Operating Characteristics). The
switches are bidirectional, so the NO, NC, and COM
terminals are both inputs or outputs.
6
NAME
MAX4696
Ground
Analog Switch, Normally Closed Terminal
Analog Switch, Common Terminal
Analog Switch, Normally Open Terminal
Power-Supply Sequencing
and Overvoltage Protection
CAUTION: Do not exceed the absolute maximum
ratings because stresses beyond the listed ratings
may cause permanent damage to devices.
Proper power-supply sequencing is recommended for
all CMOS devices. Always apply V+ before applying
analog signals, especially if the analog signal is not
current limited. If this sequencing is not possible, and if
the analog inputs are not current limited to <20mA, add
a small-signal diode (D1) as shown in Figure 6. Adding
a protection diode reduces the analog range to a diode
drop (about 0.7V) below V+ (for D1). RON increases
slightly at low supply voltages. Maximum supply volt-
_______________________________________________________________________________________
35Ω, Low-Voltage, SPST/SPDT
Analog Switches in UCSP Package
UCSP Applications Information
For the latest application details on UCSP construction,
dimensions, tape carrier information, printed circuit
board techniques, bump-pad layout, and recommended
reflow temperature profile as well as the latest information on reliability testing results, go to Maxim’s website
at www.maxim-ic.com/ucsp for the Application Note
“UCSP—A Wafer-Level Chip-Scale Package”.
Test Circuits/Timing Diagrams
MAX4696
MAX4697
MAX4698
V+
VIN
LOGIC
INPUT
V+
COM
NO
OR NC
50%
VIL
VOUT
CL
35pF
RL
300Ω
t OFF
IN
VOUT
GND
LOGIC
INPUT
SWITCH
OUTPUT
0.9 × V0UT
0.9 × VOUT
0
t ON
CL INCLUDES FIXTURE AND STRAY CAPACITANCE.
RL
VOUT = VN_
RL + RON
(
t r < 5ns
t f < 5ns
VIH
LOGIC INPUT WAVEFORMS INVERTED FOR SWITCHES
THAT HAVE THE OPPOSITE LOGIC SENSE.
)
Figure 1. Switching Time
V+
MAX4698
LOGIC
INPUT
V+
VN_
NC
50%
VIL
VOUT
COM
t r < 5ns
t f < 5ns
VIH
NO
RL
300Ω
IN
LOGIC
INPUT
CL
35pF
GND
0.9 × VOUT
VOUT
tD
CL INCLUDES FIXTURE AND STRAY CAPACITANCE.
Figure 2. Break-Before-Make Interval (MAX4698 only)
_______________________________________________________________________________________
7
MAX4696/MAX4697/MAX4698
age (V+) must not exceed +6V. Protection diode D1
also protects against some overvoltage situations. No
damage will result on the circuit in Figure 6 if the supply
voltage is below the absolute maximum rating and if a
fault voltage up to the absolute maximum rating is
applied to an analog signal terminal.
MAX4696/MAX4697/MAX4698
35Ω, Low-Voltage, SPST/SPDT
Analog Switches in UCSP Package
Test Circuits/Timing Diagrams (continued)
V+
MAX4696
MAX4697
MAX4698
∆VOUT
V+
RGEN
NC
OR NO
VOUT
COM
VOUT
IN
OFF
CL
V GEN
GND
OFF
ON
1nF
IN
VIL TO VIH
ON
OFF
IN
OFF
Q = (∆V OUT )(C L )
IN DEPENDS ON SWITCH CONFIGURATION;
INPUT POLARITY DETERMINED BY SENSE OF SWITCH.
Figure 3. Charge Injection
V+ 10nF
OFF-ISOLATION = 20log
VOUT
VIN
ON-LOSS = 20log
VOUT
VIN
CROSSTALK = 20log
VOUT
VIN
NETWORK
ANALYZER
0 OR V+
V+
IN
COM
MAX4696
MAX4697
MAX4698
NC
50Ω
NO
50Ω
VIN
VOUT
GND
50Ω
MEAS
REF
50Ω
50Ω
MEASUREMENTS ARE STANDARDIZED AGAINST SHORTS AT IC TERMINALS.
OFF-ISOLATION IS MEASURED BETWEEN COM AND "OFF" NO OR NC TERMINAL ON EACH SWITCH.
ON-LOSS IS MEASURED BETWEEN COM AND "ON" NO OR NC TERMINAL ON EACH SWITCH.
CROSSTALK IS MEASURED FROM ONE CHANNEL TO ALL OTHER CHANNELS.
SIGNAL DIRECTION THROUGH SWITCH IS REVERSED; WORST VALUES ARE RECORDED.
Figure 4. Off-Isolation/On-Channel Bandwidth, Crosstalk
V+
10nF
POSITIVE SUPPLY
D1
V+
V+
COM
MAX4696
MAX4697
MAX4698
MAX4696
MAX4697
MAX4698
IN
CAPACITANCE
METER
f = 1MHz
NC or
NO
VIL
OR
VIH
NO
COM
Vg
GND
GND
Figure 5. Channel Off/On-Capacitance
Figure 6. Overvoltage Protection Using External Blocking
Diodes
Chip Information
TRANSISTOR COUNT: 50
8
_______________________________________________________________________________________
Package Information
6L, UCSP.EPS
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 _____________________ 9
© 2003 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
MAX4696/MAX4697/MAX4698
35Ω, Low-Voltage, SPST/SPDT
Analog Switches in UCSP Package