MAXIM MAX5494ETE

19-3562; Rev 1; 6/05
10-Bit, Dual, Nonvolatile, Linear-Taper
Digital Potentiometers
♦ 35ppm/°C End-to-End Resistance Temperature
Coefficient
♦ 5ppm/°C Ratiometric Temperature Coefficient
♦ 10kΩ and 50kΩ End-to-End Resistor Values
♦ 3-Wire SPI-Compatible Serial Interface
♦ Reliability (TA = +85°C)
50,000 Wiper Store Cycles
50 Years Wiper Data Retention
♦ 1.5µA (max) Standby Current
♦ Single +2.7V to +5.25V Supply Operation
♦ Dual ±2.5V Supply Operation
N.C. 14
N.C. 15
L1
H1
9
MAX5494
MAX5495
2
3
L2
8
VSS
7
N.C.
6
N.C.
5
VDD
8
VSS
7
N.C.
6
N.C.
5
VDD
4
H2
1
GND
W1
L1
D.N.C.
12
11
10
9
N.C. 14
T1655-2
MAX5495ETE
-40°C to +85°C 16 TQFN-EP*
T1655-2
*EP = Exposed pad.
Ordering Information continued at end of data sheet.
Selector Guide appears at end of data sheet.
SPI is a trademark of Motorola, Inc.
1
2
3
4
D.N.C.
-40°C to +85°C 16 TQFN-EP*
SCLK 16
L2
MAX5494ETE
MAX5496
MAX5497
W2
PKG CODE
INTERFACE
DIN 13
CS
TEMP RANGE
10
5mm × 5mm × 0.8mm TQFN
N.C. 15
PART
11
SCLK 16
Ordering Information
PINPACKAGE
12
DIN 13
Applications
Gain and Offset Adjustment
LCD Contrast Adjustment
Pressure Sensors
Low-Drift Programmable-Gain Amplifiers
Mechanical Potentiometer Replacement
Volume Control
W1
TOP VIEW
GND
Pin Configurations
W2
The MAX5494–MAX5499 operate with either a single
power supply (+2.7V to +5.25V) or dual power supplies
(±2.5V). The devices consume 400µA (max) of supply
current when writing data to the nonvolatile memory
and 1.5µA (max) of standby supply current. The
devices are available in space-saving (5mm x 5mm x
0.8mm), 16-pin TQFN package and are specified over
the extended (-40°C to +85°C) temperature range.
♦ 16-Pin, 5mm x 5mm x 0.8mm TQFN Package
INTERFACE
The MAX5494–MAX5499 are ideal for applications requiring digitally controlled potentiometers. End-to-end resistance values of 10kΩ and 50kΩ are available with a
35ppm/°C end-to-end temperature coefficient. The ratiometric temperature coefficient is 5ppm/°C for each channel, making these devices ideal for applications requiring
low-temperature-coefficient programmable voltagedividers such as low-drift, programmable-gain amplifiers.
♦ Wiper Position Stored in Nonvolatile Memory and
Recalled Upon Power-Up
CS
The MAX5494–MAX5499 10-bit (1024-tap), dual, nonvolatile, linear-taper, programmable voltage-dividers
and variable resistors perform the function of a
mechanical potentiometer, but replace the mechanics
with a 3-wire SPI™-compatible serial interface. The
MAX5494/MAX5495 are dual, 3-terminal, programmable voltage-dividers; the MAX5496/MAX5497 are dual,
2-terminal variable resistors; and the MAX5498/
MAX5499 include one 2-terminal variable resistor and
one 3-terminal programmable voltage-divider.
The MAX5494–MAX5499 feature an internal, nonvolatile,
electrically erasable programmable read-only memory
(EEPROM) that stores the wiper position for initialization
during power-up. The 3-wire SPI-compatible serial interface allows communication at data rates up to 7MHz.
Features
5mm × 5mm × 0.8mm TQFN
Pin Configurations continued at end of data sheet.
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX5494–MAX5499
General Description
MAX5494–MAX5499
10-Bit, Dual, Nonvolatile, Linear-Taper
Digital Potentiometers
ABSOLUTE MAXIMUM RATINGS
VDD to GND ...........................................................-0.3V to +6.0V
VSS to GND............................................................-6.0V to +0.3V
VDD to VSS .............................................................-0.3V to +6.0V
H1, H2, L1, L2, W1, W2 to VSS.........(VSS - 0.3V) to (VDD + 0.3V)
CS, SCLK, DIN to GND ..............................-0.3V to (VDD + 0.3V)
Maximum Continuous Current into H_, L_, and W_
MAX5494/MAX5496/MAX5498 ....................................±5.0mA
MAX5495/MAX5497/MAX5499 ....................................±1.0mA
Maximum Current Into Other Pins .................................±50.0mA
Continuous Power Dissipation (TA = +70°C)
16-Pin TQFN (derate 20.8mW/°C above +70°C) ....1666.7mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-60°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VDD = +2.7V to +5.25V, VSS = GND = 0, VH_ = VDD, VL_ = 0, TA = -40°C to +85°C, unless otherwise noted. Typical values are at
VDD = +5.0V, TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DC PERFORMANCE (MAX5494/MAX5495/MAX5498/MAX5499 Programmable Voltage-Divider)
Resolution
N
Integral Nonlinearity (Note 2)
INL
Differential Nonlinearity (Note 2)
DNL
End-to-End Resistance
Temperature Coefficient
TCR
10
±2
VDD = 5V
±2
VDD = 2.7V
±1
VDD = 5V
±1
Ratiometric Temperature
Coefficient
Full-Scale Error
FSE
Zero-Scale Error
ZSE
Wiper Capacitance
CW
End-to-End Resistance
RHL
Channel-to-Channel Division
Ratio Matching
Bits
VDD = 2.7V
ppm/°C
5
ppm/°C
MAX5494/MAX5498
-4
-2.5
0
-4
-0.75
0
MAX5494/MAX5498
0
3.3
5
MAX5495/MAX5499
0
1.45
5
60
7.5
10
12.5
MAX5495/MAX5499
37.5
50
62.5
MAX5494
0.05
MAX5495
0.15
LSB
kΩ
%
6.3
kΩ
Resistance from W_ to L_ and H_
MAX5495/MAX5499, W_ at 15 code, H_ and
L_ shorted to VSS, measure resistance from
W_ to H_ (Figures 4 and 5)
2
LSB
pF
MAX5494/MAX5498
MAX5494/MAX5498, W_ at 15 code, H_ and
L_ shorted to VSS, measure resistance from
W_ to H_ (Figures 4 and 5)
LSB
35
MAX5495/MAX5499
VDD = 3V, midcode: 512
LSB
25
_______________________________________________________________________________________
10-Bit, Dual, Nonvolatile, Linear-Taper
Digital Potentiometers
(VDD = +2.7V to +5.25V, VSS = GND = 0, VH_ = VDD, VL_ = 0, TA = -40°C to +85°C, unless otherwise noted. Typical values are at
VDD = +5.0V, TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DC PERFORMANCE (MAX5496–MAX5499 Variable Resistor)
Resolution
N
10
VDD = 2.7V
Integral Nonlinearity (Note 3)
INL_R
VDD = 3V
-4
VDD = 5V
-4
VDD = 2.7V
Differential Nonlinearity (Note 3)
Variable-Resistor Temperature
Coefficient
Wiper Resistance
DNL_R
TCVR
RW
Wiper Capacitance
CWR
Full-Scale Wiper-to-End
Resistance
RW-L
Zero-Scale Resistor Error
RZ
Two-Channel Resistance
Matching
Bits
-1.6
-1.4
+4
-1.3
+4
+0.45
VDD = 3V
-1
+0.4
+1
VDD = 5V
-1
+0.35
+1
VDD = 3V to 5.25V; code = 128 to 1024
35
VDD ≥ 3V (Note 4)
50
Ω
60
pF
7.5
10
12.5
MAX5497/MAX5499
37.5
50
62.5
VDD = 3V to 5.25V
LSB
ppm/°C
MAX5496/MAX5498
Code = 0
LSB
MAX5494/MAX5498
70
MAX5495/MAX5499
110
MAX5496/MAX5498,
Code >128
0.1
MAX5497/MAX5499,
Code >200
0.15
kΩ
Ω
%
DIGITAL INPUTS (CS, SCLK, DIN) (Note 5)
VDD = 3.6V to 5.25V
2.4
VDD = 2.7V to 3.6V
0.7 x
VDD
Dual-supply
operation
With respect to
GND, VDD = 2.5V,
VSS = -2.5V
2.0
Single-supply
operation
VDD = 2.7V to 5.25V
0.8
Dual-supply
operation
With respect to
GND, VDD = 2.5V,
VSS = -2.5V
0.6
Single-supply
operation
Input High Voltage
VIH
Input Low Voltage
VIL
Input Leakage Current
IIN
Input Capacitance
CIN
V
V
±1
5
µA
pF
DYNAMIC CHARACTERISTICS
Wiper -3dB Bandwidth
BW
Wiper at code 495
(01111 01111), 10pF
load at wiper
MAX5494/MAX5498
250
MAX5495/MAX5499
50
kHz
_______________________________________________________________________________________
3
MAX5494–MAX5499
ELECTRICAL CHARACTERISTICS (continued)
MAX5494–MAX5499
10-Bit, Dual, Nonvolatile, Linear-Taper
Digital Potentiometers
ELECTRICAL CHARACTERISTICS (continued)
(VDD = +2.7V to +5.25V, VSS = GND = 0, VH_ = VDD, VL_ = 0, TA = -40°C to +85°C, unless otherwise noted. Typical values are at
VDD = +5.0V, TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
MAX5494/MAX5498; VDD = 3V; wiper at
code 495; 10kHz, 1VRMS signal is applied
at H_; 10pF load at wiper
Total Harmonic Distortion
TYP
MAX
0.026
THD
Analog Crosstalk
UNITS
%
MAX5495/MAX5499; VDD = 3V; wiper at
code 495; 10kHz, 1VRMS signal is applied
at H_; 10pF load at wiper
0.03
CH2 = 11111 11111, CH1 = 01111 01111,
CW_ = 10pF, VH1 = VDD = +2.5V,
VL1 = VSS = -2.5V, measure VW1 with
VW2 = 5VP-P at f = 1kHz
-93
dB
TA = +85°C
50
Years
TA = +25°C
200,000
TA = +85°C
50,000
NONVOLATILE MEMORY RELIABILITY
Data Retention
Endurance
Stores
POWER SUPPLIES
Single-Supply Voltage
Dual-Supply Voltage
Average Programming Current
VDD
VSS = GND = 0
2.70
5.25
VDD
GND = 0
2.50
5.25
VSS
(VDD - VSS) ≤ 5.25V
-2.5
-0.2
IPG
Peak Programming Current
Standby Current
4
IDD
During nonvolatile write only;
digital inputs = VDD or GND
During nonvolatile write only;
digital inputs = VDD or GND
Digital inputs = VDD or GND, TA = +25°C
220
400
4
0.6
_______________________________________________________________________________________
V
V
µA
mA
1.5
µA
10-Bit, Dual, Nonvolatile, Linear-Taper
Digital Potentiometers
(VDD = +2.7V to +5.25V, VSS = GND = 0, VH_ = VDD, VL_ = 0, TA = -40°C to +85°C, unless otherwise noted. Typical values are at
VDD = +5.0V, TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
ANALOG SECTION
Wiper Settling Time (Note 6)
tS
MAX5494/MAX5498
5
MAX5495/MAX5499
22
µs
SPI-COMPATIBLE SERIAL INTERFACE (Figure 6)
SCLK Frequency
SCLK Clock Period
SCLK Pulse-Width High
SCLK Pulse-Width Low
CS Fall to SCLK Rise Setup
SCLK Rise to CS Rise Hold
DIN to SCLK Setup
DIN Hold After SCLK
SCLK Rise to CS Fall Delay
CS Rise to SCLK Rise Hold
CS Pulse-Width High
Write NV Register Busy Time
fSCLK
tCP
tCH
tCL
tCSS
tCSH
tDS
tDH
tCS0
tCS1
tCSW
tBUSY
7
140
60
60
60
0
40
0
15
60
150
12
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ms
Note 1: 100% production tested at TA = +25°C and TA = +85°C. Guaranteed by design to TA = -40°C.
Note 2: The DNL and INL are measured for the voltage-divider with H_ = VDD and L_ = VSS. The wiper terminal (W_) is unloaded
and measured with a high-input-impedance voltmeter.
Note 3: The DNL and INL are measured with L_ = VSS = 0. For VDD = 5V, the wiper terminal is driven with a current source of IW =
80µA for the 50kΩ device and IW = 400µA for the 10kΩ device. For VDD = 3V, the wiper terminal is driven with a current
source of IW = 40µA for the 50kΩ device and IW = 200µA for the 10kΩ device.
Note 4: The wiper resistance is measured using the source currents given in Note 3.
Note 5: The device draws higher supply current when the digital inputs are driven with voltages between (VDD - 0.5V) and (GND +
0.5V). See the Supply Current vs. Digital Input Voltage graph in the Typical Operating Characteristics.
Note 6: Wiper settling test condition uses the voltage-divider with a 10pF load on W_. Transition code from 0 to 495 and measure
the time from CS going high to the wiper voltage settling to within 0.5% of its final value.
_______________________________________________________________________________________
5
MAX5494–MAX5499
TIMING CHARACTERISTICS
Typical Operating Characteristics
(VDD = +5.0V, VSS = 0, TA = +25°C, unless otherwise noted.)
VDD = 3V
1.0
0.8
0.6
0.4
0
DNL (LSB)
0.5
0.2
INL (LSB)
0
-0.2
-0.5
-0.4
-0.6
0
-0.2
-0.4
-0.6
-1.0
-0.8
-0.8
-1.5
-1.0
0
-1.0
0
128 256 384 512 640 768 896 1024
2.5
128 256 384 512 640 768 896 1024
3.0
3.5
4.0
4.5
CODE
CODE
VDD (V)
MAXIMUM INTEGRAL NONLINEARITY
vs. SUPPLY VOLTAGE (VARIABLE RESISTOR)
DIFFERENTIAL NONLINEARITY
vs. CODE (VOLTAGE-DIVIDER)
INTEGRAL NONLINEARITY
vs. CODE (VOLTAGE-DIVIDER)
0.5
VDD = 3V
0.8
1.5
MAX5494 toc05
1.0
MAX5494 toc04
1.0
0.6
VDD = 3V
1.0
0.4
-0.5
-1.0
0
0
-0.2
-0.5
-0.4
-0.6
-1.5
5.0
0.5
0.2
INL (LSB)
DNL (LSB)
0
INL (LSB)
0.2
MAX5494 toc06
DNL (LSB)
0.4
MAX5494 toc03
0.6
1.0
MAX5494 toc02
VDD = 3V
0.8
1.5
MAX5494 toc01
1.0
MAXIMUM DIFFERENTIAL NONLINEARITY
vs. SUPPLY VOLTAGE (VARIABLE RESISTOR)
INTEGRAL NONLINEARITY
vs. CODE (VARIABLE RESISTOR)
DIFFERENTIAL NONLINEARITY
vs. CODE (VARIABLE RESISTOR)
-1.0
-0.8
-2.0
-1.5
-1.0
3.0
3.5
4.0
4.5
5.0
0
VDD (V)
END-TO-END RESISTANCE
vs. CODE (MAX5497/MAX5499)
70
END-TO-END RESISTANCE vs. CODE
(MAX5496/MAX5498)
12
MAX5494 toc08
MAX5494 toc07
60
50
128 256 384 512 640 768 896 1024
CODE
CODE
WIPER RESISTANCE vs. CODE
(VARIABLE RESISTOR)
80
0
128 256 384 512 640 768 896 1024
MAX5494 toc09
2.5
10
60
40
40
30
8
RWL (kΩ)
RWL (kΩ)
50
RW (Ω)
MAX5494–MAX5499
10-Bit, Dual, Nonvolatile, Linear-Taper
Digital Potentiometers
30
6
20
4
10
2
20
10
0
0
0
128 256 384 512 640 768 896 1024
CODE
6
0
0
128 256 384 512 640 768 896 1024
CODE
0
128 256 384 512 640 768 896 1024
CODE
_______________________________________________________________________________________
10-Bit, Dual, Nonvolatile, Linear-Taper
Digital Potentiometers
END-TO-END RESISTANCE (RHL)
% CHANGE vs. TEMPERATURE
(VOLTAGE-DIVIDER)
19
18
17
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
-1.0
16
0
1
2
3
4
-15
STANDBY SUPPLY CURRENT
vs. TEMPERATURE
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
10
35
60
85
-40
0.6
VDD = 5V
1000
100
160
120
100
80
60
40
10kΩ
35
60
85
TEMPERATURE (°C)
VARIABLE RESISTOR TEMPERATURE
COEFFICIENT vs. CODE
0
1
2
3
4
600
128 256 384 512 640 768 896 1024
DIGITAL INPUT VOLTAGE (V)
CODE
TAP-TO-TAP SWITCHING TRANSIENT
(MAX5494/MAX5498)
TAP-TO-TAP SWITCHING TRANSIENT
(MAX5495/MAX5499)
MAX5494 toc16
VDD = 3V
TA = -40°C TO +85°C
0
5
MAX5494 toc17
700
50kΩ
0
0.1
10
85
140
20
-15
60
VOLTAGE-DIVIDER
VDD = 3V
TA = -40°C TO +85°C
180
1
0
35
200
10
0.3
10
RATIOMETRIC TEMPERATURE
COEFFICIENT vs. CODE
MAX5494 toc14
10,000
IDD (µA)
0.9
-40
-15
TEMPERATURE (°C)
DIGITAL SUPPLY CURRENT
vs. DIGITAL INPUT VOLTAGE
MAX5494 toc13
VDD = 5.25V
1.2
IDD (µA)
0.6
TEMPERATURE (°C)
WIPER VOLTAGE (V)
1.5
CODE IS 11 1111 1111
0.8
-1.0
-40
5
MAX5494 toc12
0.6
1.0
RATIOMETRIC TEMPCO (ppm/°C)
RW (Ω)
20
0.8
MAX5494 toc15
21
1.0
MAX5494 toc11
VDD = 5V
CODE IS 00 0000 0000
END-TO-END RESISTANCE CHANGE (%)
MAX5494 toc10
22
WIPER-TO-END RESISTANCE (RWL)
% CHANGE vs. TEMPERATURE
(VARIABLE RESISTOR)
WIPER-TO-END RESISTANCE CHANGE (%)
WIPER RESISTANCE vs. WIPER VOLTAGE
(VARIABLE RESISTOR)
MAX5494–MAX5499
Typical Operating Characteristics (continued)
(VDD = +5.0V, VSS = 0, TA = +25°C, unless otherwise noted.)
MAX5494 toc18
CS
2V/div
CS
2V/div
TCVR (ppm/°C)
500
400
VW_
20mV/div
VW_
20mV/div
300
H_ = VDD
L_ = GND
FROM CODE 01111 11111
TO CODE 10000 00000
CW_ = 10pF
200
50kΩ
10kΩ
100
H_ = VDD
L_ = GND
FROM CODE 01111 11111
TO CODE 10000 00000
CW_ = 10pF
0
0
128 256 384 512 640 768 896 1024
1µs/div
4µs/div
CODE
_______________________________________________________________________________________
7
Typical Operating Characteristics (continued)
(VDD = +5.0V, VSS = 0, TA = +25°C, unless otherwise noted.)
CROSSTALK
CROSSTALK vs. FREQUENCY
VW2
2V/div
0
MAX5494 toc20
MAX5494 toc19
CW_ = 10pF
CODE = 01111 01111
VW1
20mV/div
CROSSTALK (dB)
-20
VH2 = VDD
VL2 = VL1 = VH1 = GND
CW_ = 10pF
-40
-60
-80
MAX5494/MAX5498
-100
MAX5495/MAX5499
-120
400ns/div
0.01
0.1
1
10
100
1000
FREQUENCY (kHz)
THD+N vs. FREQUENCY
(MAX5495/MAX5499)
THD+N vs. FREQUENCY
(MAX5494/MAX5498)
CW_ = 10pF
CODE = 01111 01111
1
THD+N (%)
0.1
0.01
0.1
0.01
0.001
0.001
0.0001
0.0001
0.01
0.1
1
10
0.01
100
0.1
WIPER RESPONSE vs. FREQUENCY
(MAX5494/MAX5498)
0
-5
GAIN (dB)
-10
CW_ = 30pF
-15
-20
CW_ = 10pF
-10
CW_ = 30pF
-15
-20
CODE = 01111 01111
0.1
1
-25
10
FREQUENCY (kHz)
8
100
MAX5494 toc24
CW_ = 10pF
-5
10
WIPER RESPONSE vs. FREQUENCY
(MAX5495/MAX5499)
MAX5494 toc23
0
1
FREQUENCY (kHz)
FREQUENCY (kHz)
-25
MAX5494 toc22
CW_ = 10pF
CODE = 01111 01111
1
THD+N (%)
10
MAX5494 toc21
10
GAIN (dB)
MAX5494–MAX5499
10-Bit, Dual, Nonvolatile, Linear-Taper
Digital Potentiometers
100
1000
CODE = 01111 01111
0.1
1
10
100
1000
FREQUENCY (kHz)
_______________________________________________________________________________________
10-Bit, Dual, Nonvolatile, Linear-Taper
Digital Potentiometers
PIN
MAX5494/
MAX5495
MAX5496/
MAX5497
MAX5498/
MAX5499
NAME
FUNCTION
1
1
1
CS
Active-Low Chip-Select Input. Drive CS low to enable the serial interface. Drive
CS high to disable the serial interface and put the device in standby mode.
2
2
2
W2
Wiper Terminal 2
3
3
3
L2
Low Terminal 2
4
—
—
H2
High Terminal 2
5
5
5
VDD
6, 7,14,15
6, 7,14,15
6, 7,14,15
N.C.
No Connection. Not internally connected.
Positive Power-Supply Input. 2.7V ≤ VDD ≤ 5.25V. Bypass with a 0.1µF
capacitor from VDD to GND as close to the device as possible
8
8
8
VSS
Negative Power-Supply Input.
Single-supply operation: VSS = GND = 0.
Dual-supply operation: -2.5V ≤ VSS ≤ -0.2V (VSS can vary as long as
(VDD - VSS) ≤ 5.25V).
Bypass with a 0.1µF capacitor from VSS to GND as close to the device
as possible.
9
—
9
H1
High Terminal 1
10
10
10
L1
Low Terminal 1
11
11
11
W1
Wiper Terminal 1
12
12
12
GND
Ground
13
13
13
DIN
Serial-Data Input. The data at DIN synchronously loads into the serial shift
register on each SCLK rising edge.
16
16
16
SCLK
Serial-Clock Input . SCLK clocks in the data when CS is low.
—
4, 9
4
D.N.C
Do Not Connect. Leave unconnected for proper operation.
EP
EP
EP
Exposed
Pad
Exposed Pad. Externally connect EP to VSS to provide a low thermal resistance
path from the IC junction to the PC board or leave unconnected.
_______________________________________________________________________________________
9
MAX5494–MAX5499
Pin Descriptions
10-Bit, Dual, Nonvolatile, Linear-Taper
Digital Potentiometers
MAX5494–MAX5499
Functional Diagrams
H1
VDD
GND
VSS
CS
SCLK
DIN
POR
2 x 10
BIT
NVM
10-BIT
LATCH
10
10-BIT
LATCH
10
DECODER
1024
TAPS
W1
SPI
INTERFACE
L1
H2
MAX5494
MAX5495
DECODER
1024
TAPS
W2
L2
NOTE: THE PROGRAMMABLE VOLTAGE-DIVIDER IS NOT INTENDED FOR CURRENT TO FLOW THROUGH THE WIPER.
NOTE: SEE THE MAX5494/MAX5495/MAX5498/MAX5499 PROGRAMMABLE VOLTAGE-DIVIDERS SECTION.
Figure 1. MAX5494/MAX5495 Functional Diagram
10
______________________________________________________________________________________
10-Bit, Dual, Nonvolatile, Linear-Taper
Digital Potentiometers
VDD
GND
VSS
2 x 10
BIT
NVM
POR
CS
SCLK
DIN
10-BIT
LATCH
10
DECODER
1024
TAPS
W1
L1
SPI
INTERFACE
10-BIT
LATCH
10
DECODER
MAX5496
MAX5497
1024
TAPS
W2
L2
Figure 2. MAX5496/MAX5497 Functional Diagram
H1
VDD
GND
VSS
CS
SCLK
DIN
2 x 10
BIT
NVM
POR
10-BIT
LATCH
10
10-BIT
LATCH
10
DECODER
1024
TAPS
W1
SPI
INTERFACE
L1
MAX5498
MAX5499
DECODER
1024
TAPS
W2
L2
NOTE: THE PROGRAMMABLE VOLTAGE-DIVIDER IS NOT INTENDED FOR CURRENT TO FLOW THROUGH THE WIPER.
NOTE: SEE THE MAX5494/MAX5495/MAX5498/MAX5499 PROGRAMMABLE VOLTAGE-DIVIDERS SECTION.
Figure 3. MAX5498/MAX5499 Functional Diagram
______________________________________________________________________________________
11
MAX5494–MAX5499
Functional Diagrams (continued)
Detailed Description
The MAX5494–MAX5499 dual, nonvolatile, linear-taper,
programmable voltage-dividers and variable resistors
feature 1024 tap points (10-bit resolution) (see the
Functional Diagrams). These devices consist of multiple strings of equal resistor segments with a wiper contact that moves among the 1024 effective tap points by
a 3-wire SPI-compatible serial interface. The
MAX5494/MAX5496/MAX5498 provide a total 10kΩ
end-to-end resistance, and the MAX5495/MAX5497/
MAX5499 feature a 50kΩ end-to-end resistance. The
MAX5494/MAX5495/MAX5498/MAX5499 allow access
to the high, low, and wiper terminals for a standard voltage-divider configuration. Ensure that the terminal voltages fall between VSS and VDD.
MAX5494/MAX5495/MAX5498/MAX5499
Programmable Voltage-Dividers
The MAX5494/MAX5495/MAX5498/MAX5499 programmable voltage-dividers provide a weighted average of
the voltage between the H_ and L_ inputs at the W_
output.
The MAX5494/MAX5495/MAX5498/MAX5499 programmable voltage-divider network provides up to 1024
division ratios between the H_ and L_ voltage. Ideally,
the VL voltage occurs at the wiper terminal when all
data bits are zeros and the VH voltage occurs at the
wiper terminal when all data bits are one (see the wiper
voltage equation). The step-size voltage (1 LSB) is
equal to the voltage applied across terminals H and L
divided by 210. Calculate the wiper voltage VW as follows:
where D is the decimal equivalent of the 10 data bits
written (0 to 1023), VHL is the voltage difference between
the H_ and L_ terminals, and:
V 
VFSE = FSE HL 
 1024 
V 
VZSE = ZSE HL 
 1024 
The MAX5494/MAX5498 provide a 10kΩ end-to-end
resistance value, while the MAX5495/MAX5499 feature a
50kΩ end-to-end resistance value. Note that the programmable voltage-divider is not intended to be used
as a variable resistor. Wiper current creates a nonlinear
voltage drop in series with the wiper. To ensure temperature drift remains within specifications, do not pull current
through the voltage-divider wiper. Connect the wiper to a
high-impedance node. Figures 4 and 5 show the behavior of the programmable voltage-divider resistance from
W_ to H_ and W_ to L_, respectively. This does not apply
to the variable-resistor devices.
MAX5496–MAX5499 Variable Resistors
The MAX5496–MAX5499 provide a programmable resistance from W_ to L_. The MAX5496/MAX5498 provide a
10kΩ end-to-end resistance value, while the
MAX5497/MAX5499 feature a 50kΩ end-to-end resistance value. The programmable resolution of this
18
18
16
16
14
14
12
12
10
8
10
8
6
6
4
4
2
2
0
0
0
128 256 384 512 640 768 896 1024
CODE (DECIMAL)
50kΩ SCALES BY A FACTOR OF FIVE
Figure 4. Resistance from W_ to H_ vs. Code (10kΩ VoltageDivider)
12
 VHL − (| VFSE | + | VZSE |) 
D
 + VL + | VZSE |
1023


RW_L_ (kΩ)
RW_H_ (kΩ)
MAX5494–MAX5499
10-Bit, Dual, Nonvolatile, Linear-Taper
Digital Potentiometers
0
128 256 384 512 640 768 896 1024
CODE (DECIMAL)
50kΩ SCALES BY A FACTOR OF FIVE
Figure 5. Resistance from W_ to L_ vs. Code (10kΩ VoltageDivider)
______________________________________________________________________________________
10-Bit, Dual, Nonvolatile, Linear-Taper
Digital Potentiometers
D
RWL (D) =
× RW−L + RZ
1023
where D is decimal equivalent of the 10 data bits written, RW-L is the nominal end-to-end resistance, and RZ
is the zero-scale error. Table 1 shows RWL at selected
codes.
either eight clock cycles to transfer the command bits
(Figure 7b) or 24 clock cycles with 16 bits disregarded
by the device (Figure 7a).
After the loading of data into the shift register, drive CS
high to latch the data into the appropriate control register (specified by RA1 and RA0) and disable the serial
interface. Keep CS low during the entire serial data
stream to avoid corruption of the data. Table 2 shows
the register map.
Write Wiper Register
The “write wiper register” command (C1, C0 = 00) controls the wiper positions. The 10 data bits (D9–D0) indicate the position of the wiper. For example, if DIN =
000000 0000, the wiper moves to the position closest to
L_. If DIN = 11 1111 1111, the wiper moves closest to H_.
Table 1. RWL at Selected Codes
SPI-Compatible Serial Interface
The MAX5494–MAX5499 use a 3-wire, SPI-compatible,
serial data interface (Figure 6). This write-only interface
contains three inputs: chip-select (CS), data input
(DIN), and data clock (SCLK). Drive CS low to enable
the serial interface and clock data synchronously into
the shift register on each SCLK rising edge.
The WRITE commands (C1, C0 = 00 or 01) require 24
clock cycles to transfer the command and data (Figure
7a). The COPY commands (C1, C0 = 10 or 11) use
END-TO-END RESISTANCE VALUE
CODE (DECIMAL)
10kΩ
50kΩ
RWL (Ω)
RWL (Ω)
0
70
110
1
80
160
512
5,070
25,110
1023
10,070
50,110
CS
tCSW
tCSS
tCL
tCSO
tCH
tCP
tCSH
tCS1
SCLK
tDS
tDH
DIN
Figure 6. SPI-Interface Timing Diagram
______________________________________________________________________________________
13
MAX5494–MAX5499
resistance is equal to the nominal end-to-end resistance divided by 1024 (10-bit resolution). For example,
the programmable resolution is 9.8Ω and 48.8Ω for the
MAX5496/MAX5498 and the MAX5497/MAX5499,
respectively.
The 10-bit data in the 10-bit latch register selects the
wiper position from the 1024 possible positions, resulting in 1024 values for the resistance from W_ to L_.
Calculate the resistance from W_ to L_ (RWL) from the
formula below:
MAX5494–MAX5499
10-Bit, Dual, Nonvolatile, Linear-Taper
Digital Potentiometers
a) 24-BIT COMMAND/DATA WORD
CS
SCLK
1
2
3
4
5
6
8
9
RA1 RA0 D9
C1 C0
DIN
7
10
11
12
13
14
15
16
17
18
D8
D7
D6
D5
D4
D3
D2
D1
D0
19
20
21
22
23
24
b) 8-BIT COMMAND WORD
CS
SCLK
1
2
DIN
3
4
5
6
C1 C0
7
8
RA1 RA0
Figure 7. SPI-Compatible Serial-Interface Format
Table 2. Register Map*
1
2
3
4
5
6
Bit Name
CLOCK EDGE
—
—
C1
C0
—
—
7
Write Wiper Register 1
0
0
0
0
0
0
0
Write Wiper Register 2
0
0
0
0
0
0
Write NV Register 1
0
0
0
1
0
0
Write NV Register 2
0
0
0
1
0
Copy Wiper Register 1
to NV Register 1
0
0
1
0
Copy Wiper Register 2
to NV Register 2
0
0
1
Copy Wiper Register 1
to NV Register 1 and
Copy Wiper Register 2
to NV Register 2
Simultaneously
0
0
Copy NV Register 1 to
Wiper Register 1
0
Copy NV Register 2 to
Wiper Register 2
Copy NV Register 1 to
Wiper Register 1 and
Copy NV Register 2 to
Wiper Register 2
Simultaneously
8
9
10
11
12
13
14
15
16
17
18
…
24
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
—
—
1
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
—
—
1
0
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
—
—
0
1
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
—
—
0
1
0
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
—
—
0
0
0
1
—
—
—
—
—
—
—
—
—
—
—
—
0
0
0
1
0
—
—
—
—
—
—
—
—
—
—
—
—
1
0
0
0
1
1
—
—
—
—
—
—
—
—
—
—
—
—
0
1
1
0
0
0
1
—
—
—
—
—
—
—
—
—
—
—
—
0
0
1
1
0
0
1
0
—
—
—
—
—
—
—
—
—
—
—
—
0
0
1
1
0
0
1
1
—
—
—
—
—
—
—
—
—
—
—
—
RA1 RA0
*D9 is the MSB and D0 is the LSB of the data bits.
14
______________________________________________________________________________________
10-Bit, Dual, Nonvolatile, Linear-Taper
Digital Potentiometers
Write NV Register
The “write NV register” command (C1, C0 = 01) stores
the position of the wiper to the NV registers for use at
power-up. Alternatively, the “copy wiper register to NV
register” command writes to the NV register. Writing to
the NV register does not affect the position of the
wipers. The operation takes up to 12ms (max) after CS
goes high to complete and no other operation should
be performed until completion. Figure 9 shows how to
write data to the NV register 1.
Copy Wiper Register to NV Register
The “copy wiper register to NV register” command (C1,
C0 = 10) stores the current position of the wiper to the
NV register for use at power-up. Figure 10 shows how
to copy data from wiper register 1 to NV register 1.
CS
1
2
3
4
5
6
7
8
9
10
11 12 13 14
15
16
17
18
19 20 21 22
23
24
SCLK
C1 C0
DIN
0
0
0
RA1 RA0
0
0
0
0
1
D9 D8 D7 D6 D5 D4 D3 D2
D1 D0
X
X
X
X
X
X
WIPER
REGISTER 1
UPDATED
ACTION
Figure 8. Write Wiper Register 1
CS
1
2
3
4
5
6
7
8
9
10
11 12 13 14
15
16
17
18
19 20 21 22
23
24
SCLK
C1 C0
DIN
0
0
0
1
RA1 RA0
0
0
0
1
D9 D8 D7 D6 D5 D4 D3 D2
D1 D0
X
X
X
X
X
X
tBUSY
WRITE NV
REGISTER 1
(DEVICE IS BUSY)
ACTION
Figure 9. Write NV Register 1
______________________________________________________________________________________
15
MAX5494–MAX5499
The “write wiper register” command writes data to the
volatile random access memory (RAM), leaving the NV
registers unchanged. When the device powers up, the
data stored in the NV registers transfers to the wiper
register, moving the wiper to the stored position. Figure
8 shows how to write data to wiper register 1.
MAX5494–MAX5499
10-Bit, Dual, Nonvolatile, Linear-Taper
Digital Potentiometers
Copy NV Register to Wiper Register
The “copy NV register to wiper register” (C1, C0 = 11)
restores the wiper position to the current value stored in
the NV register. Figure 11 shows how to copy data from
NV register 1 to wiper register 1.
Standby Mode
The MAX5494–MAX5499 feature a low-power standby
mode. When the device is not being programmed, it
enters into standby mode and supply current drops to
0.6µA (typ).
Nonvolatile Memory
The internal EEPROM consists of a nonvolatile register
that retains the last value stored prior to power-down.
The nonvolatile register is programmed to midscale at
CS
Power-Up
Upon power-up, the MAX5494–MAX5499 load the data
stored in the nonvolatile wiper register into the wiper
register, updating the wiper position with the data
stored in the nonvolatile wiper register.
Applications Information
The MAX5494–MAX5499 are intended for circuits
requiring digitally controlled adjustable resistance,
such as LCD contrast control (where voltage biasing
adjusts the display contrast), or programmable filters
with adjustable gain and/or cutoff frequency.
CS
1
2
3
4
5
6
7
8
1
SCLK
DIN
the factory. The nonvolatile memory is guaranteed for
50 years for wiper data retention and up to 200,000
wiper write cycles.
2
3
4
5
6
7
8
RA1
RA0
0
1
SCLK
0
0
C1
C0
1
0
0
0
RA1
RA0
0
1
DIN
0
0
C1
C0
1
1
0
0
tBUSY
ACTION
WRITE NV
REGISTER 1
(DEVICE IS BUSY)
Figure 10. Copy Wiper Register 1 to NV Register 1
16
ACTION
Figure 11. Copy NV Register 1 to Wiper Register 1
______________________________________________________________________________________
WIPER REGISTER
1 UPDATED
10-Bit, Dual, Nonvolatile, Linear-Taper
Digital Potentiometers
R1
R2
1
fC =
2π × R3 × C
G = 1+
Programmable Filter
Figure 14 shows the configuration for a 1st-order programmable filter. The gain of the filter is adjusted by
R2, and the cutoff frequency is adjusted by R3. Use the
following equations to calculate the gain (G) and the
3dB cutoff frequency (fC).
Gain and Offset Voltage Adjustment
Figure 15 shows an application using the MAX5498/
MAX5499 to adjust the gain and nullify the offset voltage.
5V
5V
H_
30V
30V
1/2 MAX5494/MAX5495
1/2 MAX5498/MAX5499
W_
VOUT
MAX480
MAX480
VOUT
L_
1/2 MAX5496–MAX5499
W_
L_
Figure 12. Positive LCD Bias Control Using a Voltage-Divider
Figure 13. Positive LCD Bias Control Using a Variable Resistor
C
VREF
VIN
H_
VOUT
1/2 MAX5498/MAX5499
R3
1/2 MAX5496–MAX5499
W_
W_
R1
VOUT
L_
L_
1/2 MAX5496–MAX5499
R2
1/2 MAX5498/MAX5499
W_
W_
L_
Figure 14. Programmable Filter
VIN
L_
Figure 15. Gain- and Offset-Voltage Adjustment Circuit
______________________________________________________________________________________
17
MAX5494–MAX5499
Positive LCD Bias Control
Figures 12 and 13 show an application where the voltage-divider or variable resistor is used to make an
adjustable, positive LCD-bias voltage. The op amp provides buffering and gain to the resistor-divider network.
Selector Guide
PART
END-TO-END
RESISTANCE
(kΩ)
CONFIGURATION
MAX5494ETE
Two programmable voltagedividers
10
MAX5495ETE
Two programmable voltagedividers
50
MAX5496ETE
Two variable resistors
10
MAX5497ETE
Two variable resistors
50
MAX5498ETE
One programmable voltagedivider and one variable resistor
10
MAX5499ETE
One programmable voltagedivider and one variable resistor
50
Ordering Information (continued)
PART
PINPACKAGE
TEMP RANGE
MAX5496ETE
-40°C to +85°C 16 TQFN-EP*
T1655-2
-40°C to +85°C 16 TQFN-EP*
T1655-2
MAX5498ETE
-40°C to +85°C 16 TQFN-EP*
T1655-2
MAX5499ETE
-40°C to +85°C 16 TQFN-EP*
T1655-2
*EP = Exposed pad.
Chip Information
TRANSISTOR COUNT: 32,262
PROCESS: BiCMOS
GND
W1
L1
H1
TOP VIEW
12
11
10
9
N.C. 14
N.C. 15
INTERFACE
DIN 13
MAX5498
MAX5499
1
2
3
4
W2
L2
D.N.C.
SCLK 16
8
VSS
7
N.C.
6
N.C.
5
VDD
5mm × 5mm × 0.8mm TQFN
18
PKG CODE
MAX5497ETE
Pin Configurations (continued)
CS
MAX5494–MAX5499
10-Bit, Dual, Nonvolatile, Linear-Taper
Digital Potentiometers
______________________________________________________________________________________
10-Bit, Dual, Nonvolatile, Linear-Taper
Digital Potentiometers
QFN THIN.EPS
D2
D
MARKING
b
C
L
0.10 M C A B
D2/2
D/2
k
L
XXXXX
E/2
E2/2
C
L
(NE-1) X e
E
DETAIL A
PIN # 1
I.D.
e/2
E2
PIN # 1 I.D.
0.35x45°
e
(ND-1) X e
DETAIL B
e
L1
L
C
L
C
L
L
L
e
e
0.10 C
A
C
0.08 C
A1 A3
PACKAGE OUTLINE,
16, 20, 28, 32, 40L THIN QFN, 5x5x0.8mm
-DRAWING NOT TO SCALE-
21-0140
H
1
2
______________________________________________________________________________________
19
MAX5494–MAX5499
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
MAX5494–MAX5499
10-Bit, Dual, Nonvolatile, Linear-Taper
Digital Potentiometers
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
COMMON DIMENSIONS
PKG.
16L 5x5
20L 5x5
EXPOSED PAD VARIATIONS
28L 5x5
32L 5x5
40L 5x5
SYMBOL MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX.
A
A1
A3
b
D
E
e
k
L
L1
N
ND
NE
JEDEC
0.70 0.75 0.80 0.70 0.75 0.80 0.70 0.75 0.80 0.70 0.75 0.80 0.70 0.75 0.80
0
0.02 0.05
0
0.02 0.05
0.20 REF.
0.20 REF.
0.25 0.30 0.35 0.25 0.30 0.35
4.90 5.00 5.10 4.90 5.00 5.10
4.90 5.00 5.10 4.90 5.00 5.10
0.80 BSC.
0.65 BSC.
0.25 - 0.25 -
0
0.02 0.05
0
0.02 0.05
0.20 REF.
0.20 REF.
0.20 0.25 0.30
4.90 5.00 5.10
4.90 5.00 5.10
0.50 BSC.
0.25 -
0.20 0.25 0.30
4.90 5.00 5.10
4.90 5.00 5.10
0.50 BSC.
0.25
-
0
0.02 0.05
0.20 REF.
0.15 0.20 0.25
4.90 5.00 5.10
4.90 5.00 5.10
0.40 BSC.
0.25 0.35 0.45
0.30 0.40 0.50 0.45 0.55 0.65 0.45 0.55 0.65 0.30 0.40 0.50 0.40 0.50 0.60
- 0.30 0.40 0.50
16
20
28
32
40
4
5
7
8
10
4
5
7
8
10
WHHB
WHHC
WHHD-1
WHHD-2
-----
NOTES:
1. DIMENSIONING & TOLERANCING CONFORM TO ASME Y14.5M-1994.
2. ALL DIMENSIONS ARE IN MILLIMETERS. ANGLES ARE IN DEGREES.
3. N IS THE TOTAL NUMBER OF TERMINALS.
4. THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL
CONFORM TO JESD 95-1 SPP-012. DETAILS OF TERMINAL #1 IDENTIFIER ARE
OPTIONAL, BUT MUST BE LOCATED WITHIN THE ZONE INDICATED. THE TERMINAL #1
IDENTIFIER MAY BE EITHER A MOLD OR MARKED FEATURE.
D2
L
E2
PKG.
CODES
MIN.
NOM. MAX.
T1655-1
T1655-2
T1655N-1
3.00
3.00
3.00
3.10 3.20 3.00
3.10 3.20 3.00
3.10 3.20 3.00
3.10
3.10
3.10
3.20
3.20
3.20
T2055-2
T2055-3
T2055-4
3.00
3.00
3.00
3.10 3.20 3.00
3.10 3.20 3.00
3.10 3.20 3.00
3.10
3.10
3.10
3.20
3.20
3.20
T2055-5
T2855-1
T2855-2
T2855-3
T2855-4
T2855-5
T2855-6
T2855-7
T2855-8
T2855N-1
T3255-2
T3255-3
T3255-4
T3255N-1
3.15
3.15
2.60
3.15
2.60
2.60
3.15
2.60
3.15
3.15
3.00
3.00
3.00
3.00
3.25
3.25
2.70
3.25
2.70
2.70
3.25
2.70
3.25
3.25
3.10
3.10
3.10
3.10
3.15
3.15
2.60
3.15
2.60
2.60
3.15
2.60
3.15
3.15
3.00
3.00
3.00
3.00
3.25
3.25
2.70
3.25
2.70
2.70
3.25
2.70
3.25
3.25
3.10
3.10
3.10
3.10
3.35
3.35
2.80
3.35
2.80
2.80
3.35
2.80
3.35
3.35
3.20
3.20
3.20
3.20
T4055-1
3.20
3.30 3.40 3.20
3.30
3.40
3.35
3.35
2.80
3.35
2.80
2.80
3.35
2.80
3.35
3.35
3.20
3.20
3.20
3.20
MIN.
NOM. MAX.
±0.15
**
**
**
**
**
**
0.40
DOWN
BONDS
ALLOWED
NO
YES
NO
NO
YES
NO
YES
**
NO
NO
YES
YES
NO
**
**
0.40
**
**
**
**
**
NO
YES
YES
NO
NO
YES
NO
NO
**
YES
**
**
**
**
** SEE COMMON DIMENSIONS TABLE
5. DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN
0.25 mm AND 0.30 mm FROM TERMINAL TIP.
6. ND AND NE REFER TO THE NUMBER OF TERMINALS ON EACH D AND E SIDE RESPECTIVELY.
7. DEPOPULATION IS POSSIBLE IN A SYMMETRICAL FASHION.
8. COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS.
9. DRAWING CONFORMS TO JEDEC MO220, EXCEPT EXPOSED PAD DIMENSION FOR T2855-1,
T2855-3, AND T2855-6.
10. WARPAGE SHALL NOT EXCEED 0.10 mm.
11. MARKING IS FOR PACKAGE ORIENTATION REFERENCE ONLY.
12. NUMBER OF LEADS SHOWN ARE FOR REFERENCE ONLY.
13. LEAD CENTERLINES TO BE AT TRUE POSITION AS DEFINED BY BASIC DIMENSION "e", ±0.05.
PACKAGE OUTLINE,
16, 20, 28, 32, 40L THIN QFN, 5x5x0.8mm
21-0140
-DRAWING NOT TO SCALE-
H
2
2
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
20 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2005 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products, Inc.