19-1254; Rev 0; 7/97 UAL IT MAN TION K A ET U E L H A S EV TA WS DA FOLLO 3.3V/5V or Adjustable, Step-Up/Down DC-DC Converters ________________________Applications Single-Cell, Lithium-Powered Portable Devices Digital Cameras 2- to 4-Cell AA Alkaline Hand-Held Equipment 3.3V and Other Low-Voltage Systems 2-, 3-, and 4-Cell Battery-Powered Equipment Battery-Powered Devices with AC Input Adapters __________Typical Operating Circuit C1 N/E LBO LBI+ STBY 3.3V ♦ Step-Up/Down Voltage Conversion ♦ +1.8V to +11V Input Range ♦ Output: 5V/250mA at VIN = 1.8V 5V/500mA at VIN = 3.6V ♦ No External FETs Required ♦ Load Disconnected from Input in Shutdown ♦ Battery Drain: 200µA No-Load (VIN = 4V) 7µA in Standby 0.2µA when Off ♦ Low-Noise and High-Efficiency Modes ______________Ordering Information PART TEMP. RANGE MAX710C/D 0°C to +70°C MAX710ESE MAX711C/D MAX711ESE -40°C to +85°C 0°C to +70°C -40°C to +85°C PIN-PACKAGE Dice 16 Narrow SO Dice 16 Narrow SO __________________Pin Configuration TOP VIEW +1.8V TO +11V INPUT ON ____________________________Features OFF SHDN ON MAX710 L1 C2 PS OUTPUT 3.3V/5V OUT C4 REF PGND GND ILIM 14 GND ILIM 3 SHDN 4 3/5 LBI- 15 PGND PGND 2 LX STBY 5V 16 LX LX 1 STBY 5 MAX710 MAX711 13 REF 12 PS 3/5 (FB) 6 11 LBI+ N/E 7 10 LBI- LBO 8 9 C3 0.1µF OUT SO ( ) IS FOR THE MAX711. ________________________________________________________________ Maxim Integrated Products 1 For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800. For small orders, phone 408-737-7600 ext. 3468. MAX710/MAX711 _______________General Description The MAX710/MAX711 integrate a step-up DC-DC converter with a linear regulator to provide step-up/down voltage conversion. They are optimized for battery applications where the input varies above and below the regulated output voltage. They have an input range from +1.8V to +11V. Typical efficiency when boosting battery inputs is 85%. The MAX710/MAX711 can be configured for minimum noise or optimum efficiency. Shutdown control turns off the part completely, disconnecting the input from the output (ISHDN = 0.2µA). Standby control turns off only the step-up converter and leaves the low-power linear regulator active (IQ = 7µA). The MAX710 has a preset 3.3V or 5V output voltage. The MAX711 has an adjustable output that can be set from +2.7V to +5.5V with two resistors. Both devices come in 16-pin narrow SO packages. MAX710/MAX711 3.3V/5V or Adjustable, Step-Up/Down DC-DC Converters ABSOLUTE MAXIMUM RATINGS PS, LX, OUT to GND............................................-0.3V to +11.5V ILIM, SHDN, STBY, FB, 3/5, N/E, LBO, LBI-, LBI+, REF to GND ...........................-0.3V to (VPS + 0.3V) PGND to GND .......................................................-0.3V to +0.3V REF Short Circuit to GND ...........................................Continuous IOUT ...................................................................................700mA Continuous Power Dissipation (TA = +70°C) SO (derate 8.70mW/°C above +70°C) ..........................696mW Operating Temperature Range ...........................-40°C to +85°C Storage Temperature Range .............................-65°C to +160°C Junction Temperature ......................................................+150°C Lead Temperature (soldering, 10sec) .............................+300°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VPS = 5.6V, STBY = PS, CREF = 0.1µF, COUT = 4.7µF, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1) PARAMETER Input Voltage CONDITIONS MIN MAX 1.8 11.0 N/E = GND (Note 2) 1.8 7.0 Full Load Start-Up Voltage Output Voltage (MAX710) TYP N/E = PS 0.9 V V 3/5 = low, IOUT = 0 to 250mA TA = 0°C to +85°C 4.8 5.0 5.2 TA = -40°C to +85°C 4.6 5.0 5.3 3/5 = high, IOUT = 0 to 250mA, VPS = 4.7V TA = 0°C to +85°C 3.17 3.3 3.43 TA = -40°C to +85°C 3.05 3.3 3.55 MAX711 Output Voltage Load Regulation 0 < IOUT < 250mA, STBY = PS 0.5 % Output Voltage Line Regulation STBY = PS, 1.8V to 5V 0.3 %/V Quiescent Current V STBY = V SHDN = logic high, current measured into PS pin; ILOAD = 0 100 140 µA Standby Quiescent Current V STBY = 0V 7 16 µA Shutdown Quiescent Current V SHDN = 0V µA Standby Output Current 5.5 V Output Voltage-Adjustment Range Reference Voltage FB UNITS 0.1 5 TA = 0°C to +85°C, IREF = 0 1.24 1.28 1.31 TA = -40°C to +85°C, IREF = 0 1.23 1.28 1.32 TA = 0°C to +85°C 1.20 1.25 1.29 TA = -40°C to +85°C 1.18 1.25 1.31 0.1 1 % nA V STBY = 0V, linear regulator 10 FB Voltage MAX711, OUT = FB Load Regulation MAX711, OUT = FB FB Input Current FB = 1.25V 1 50 VPS = 5.6V 0.2 0.6 MAX710, VPS = 3.7V 0.3 0.9 MAX711, VPS = 2.7V 0.6 1.2 VLX = 5.6V 0.1 1 LX On-Resistance LX Leakage Current LX Current Limit 2 V 0mA ≤ ILOAD ≤ 250mA ILIM = PS 0.5 0.8 1.3 ILIM = GND 1.1 1.5 1.95 _______________________________________________________________________________________ V mA mV Ω µA A 3.3V/5V or Adjustable, Step-Up/Down DC-DC Converters (VPS = 5.6V, STBY = PS, CREF = 0.1µF, COUT = 4.7µF, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1) PARAMETER Output PFET Resistance TYP MAX VOUT = 5.0V CONDITIONS MIN 0.7 1.3 MAX710, VOUT = 3.0V 1.3 2.4 UNITS Ω MAX711, VOUT = 2.7V 1.6 3.0 Output PFET Leakage VPS = 3V, VOUT = 0V 0.4 3 Thermal Shutdown STBY = PS 150 °C STBY = PS 20 °C Thermal Shutdown Hysteresis µA LOGIC Input Low Voltage STBY, SHDN, N/E, 3/5, ILIM Input High Voltage STBY, SHDN, N/E, 3/5, ILIM Input Bias Current STBY, SHDN, N/E, 3/5, ILIM 0.4 1.6 V V 1 50 nA 10 V LBI/LBO COMPARATOR Input Range LBI-, LBI+ (Note 3) Input Bias Current LBI-, LBI+ VLBI-, VLBI+ = 1.25V Hysteresis 1.2 6 LBI/LBO Offset Voltage LBO Output Voltage VLBI- = 1.25V 1 50 nA 40 100 mV +25 mV -25 ILBO = 2mA, VLBI- = 1.25V, VLBI+ = 1V ILBO = -300µA, VLBI- = 1.25V, VLBI+ = 2V 0.4 VPS - 0.2V V Note 1: Specifications at -40°C are guaranteed by design, not production tested. Note 2: Guaranteed by design (see Table 1). Note 3: The LBO comparator provides the correct result as long as one input is within the specified input range. _______________________________________________________________________________________ 3 MAX710/MAX711 ELECTRICAL CHARACTERISTICS (continued) __________________________________________Typical Operating Characteristics (TA = +25°C, unless otherwise noted.) EFFICIENCY vs. OUTPUT CURRENT— HIGH-EFFICIENCY MODE (VOUT = 3.3V) VIN = 2.5V VIN = 1.8V VIN = 1V 60 VIN = 1.8V 70 VIN = 1V 1 10 100 0.8 0.6 VOUT = 5V N/E = PS 1 10 100 0 1000 50 100 150 200 250 OUTPUT CURRENT (mA) OUTPUT CURRENT (mA) LOAD CURRENT (mA) EFFICIENCY vs. LOAD CURRENT— HIGH-EFFICIENCY AND LOW-NOISE MODES (VOUT = 5V) EFFICIENCY vs. LOAD CURRENT— HIGH-EFFICIENCY AND LOW-NOISE MODES (VOUT = 3.3V) NO-LOAD BATTERY CURRENT vs. INPUT VOLTAGE HIGH-EFFICIENCY MODE ILIM = 0.8A EFFICIENCY (%) 70 N/E = PS ILIM = 1.5A 80 ILIM = 0.8A 70 ILIM = 1.5A 0.1 1 10 100 ILIM = GND (1.5A) 600 ILIM = PS (0.8A) 1 10 100 0 1000 2 4 6 8 10 LOAD CURRENT (mA) LOAD CURRENT (mA) INPUT VOLTAGE (V) MAXIMUM OUTPUT CURRENT vs. INPUT VOLTAGE LINEAR-REGULATOR POWER-SUPPLY REJECTION RATIO vs. FREQUENCY SHUTDOWN CURRENT vs. INPUT VOLTAGE 50 45 PSRR (dB) ILIM = PS 100 40 35 30 25 N/E = GND 20 N/E = PS 15 10 1.4 1.6 1.8 2.0 INPUT VOLTAGE (V) 2.2 2.4 2.6 0.8 0.6 0.4 0.2 0 10 1.2 1.0 12 MAX710/711 TOC09 55 SHUTDOWN CURRENT (µA) 60 MAX710/711 TOC08 ILIM = GND MAX710/711 TOC07 1000 1.0 800 0 0.1 1000 1000 200 50 50 1200 400 VOUT = 3.3V VIN = 2.5V VOUT = 5V VIN = 2.5V N/E = GND 1400 LOW-NOISE MODE 60 60 1600 SUPPLY CURRENT (µA) ILIM = 0.8A ILIM = 1.5A 80 MAX710/711 TOC05 N/E = GND 90 MAX710/711 TOC04 90 EFFICIENCY (%) 1.0 0 0.1 1000 1.2 0.2 50 0.1 1.4 0.4 VOUT = 3.3V N/E = GND 50 4 1.6 60 VOUT = 5V N/E = GND MAX710/711 TOC03 80 1.8 INPUT VOLTAGE (V) VIN = 3.6V 70 VIN = 2.5V EFFICIENCY (%) 80 2.0 MAX710/711 TOC02 VIN = 5.6V EFFICIENCY (%) 90 MAX710/711 TOC01 90 MINIMUM START-UP INPUT VOLTAGE vs. LOAD CURRENT MAX710/711 TOC06 EFFICIENCY vs. OUTPUT CURRENT— HIGH-EFFICIENCY MODE (VOUT = 5V) MAXIMUM OUTPUT CURRENT (mA) MAX710/MAX711 3.3V/5V or Adjustable, Step-Up/Down DC-DC Converters 0.01 0.1 1 10 FREQUENCY (kHz) 100 1000 1 2 3 4 5 6 7 8 INPUT VOLTAGE (V) _______________________________________________________________________________________ 9 10 11 3.3V/5V or Adjustable, Step-Up/Down DC-DC Converters LINE-TRANSIENT RESPONSE LOAD-TRANSIENT RESPONSE MAX710/711 TOC10 MAX710/711 TOC11 A A B B 2ms/div 1ms/div A: VOUT = 3.3V (50mV/div, AC COUPLED), N/E = PS B: IOUT = 10mA TO 100mA A: VOUT = 3.3V (100mV/div, AC COUPLED), N/E = GND B: VIN = 2V TO 4V, IOUT = 100mA OUTPUT RIPPLE (LOW-NOISE MODE) OUTPUT RIPPLE (HIGH-EFFICIENCY MODE) MAX710/711 TOC13 MAX710/711 TOC12 200µs/div 200µs/div VIN = 2.5V, IOUT = 20mA, N/E = PS VOUT = 5V (20mV/div, AC COUPLED), IOUT = 20mA VIN = 2.5V, IOUT = 20mA, N/E = GND VOUT = 5V (20mV/div, AC COUPLED), IOUT = 20mA START-UP DELAY TURN-OFF DELAY MAX710/711 TOC14 20µs/div A: VOUT (2V/div), IOUT = 100mA B: VSHDN (2V/div) MAX710/711 TOC15 A A B B 200µs/div A: VOUT (2V/div), IOUT = 100mA B: VSHDN (2V/div) _______________________________________________________________________________________ 5 MAX710/MAX711 ____________________________Typical Operating Characteristics (continued) (TA = +25°C, unless otherwise noted.) MAX710/MAX711 3.3V/5V or Adjustable, Step-Up/Down DC-DC Converters ______________________________________________________________Pin Description PIN NAME FUNCTION MAX710 MAX711 1 1 LX 2 2 PGND 3 3 ILIM 4 4 SHDN Shutdown Input. When low, the entire circuit is off and OUT is actively pulled to GND. 5 5 STBY Standby Input. Connect to GND to disable boost circuit. Connect to PS for normal operation. Drain Connection for internal N-channel power MOSFET Power Ground Inductor Current-Limit-Select Input. Connect to GND for 1.5A limit and to PS for 0.8A limit. 6 — 3/5 Selects the output voltage. Connect to GND for 5V output and to OUT for 3.3V output. — 6 FB Feedback Input 7 7 N/E Selects low-noise or high-efficiency mode. Connect to GND for high efficiency and to PS for lowest noise. See Operating Configurations section. 8 8 LBO Low-Battery Comparator Output 9 9 OUT Linear-Regulator Output. Bypass with a 4.7µF capacitor to GND. 10 10 LBI- Negative Input to Low-Battery Comparator 11 11 LBI+ Positive Input to Low-Battery Comparator 12 12 PS 13 13 REF 1.28V Reference Voltage Output. Bypass with a 0.1µF capacitor to GND. 14 14 GND Analog Ground. Must be low impedance. Solder directly to ground plane. 15 15 PGND 16 16 LX Source of internal PFET regulator. The IC is powered from PS. Power Ground Drain Connection for internal N-channel power MOSFET _______________Detailed Description The MAX710/MAX711 integrate a step-up DC-DC converter with a linear regulator to provide step-up/down voltage conversion. The step-up switch-mode regulator contains an N-channel power MOSFET switch. It also shares a precision voltage reference with a linear regulator that contains a P-channel MOSFET pass element (Figure 1). Step-Up Operation A pulse-frequency-modulation (PFM) control scheme with a constant 1µs off-time and variable on-time controls the N-channel MOSFET switch. The N-channel switch turns off when the part reaches the peak current limit or the 4µs maximum on-time. The ripple frequency is a function of load current and input voltage. Step-Down Operation The low-dropout linear regulator consists of a reference, an error amplifier, and a P-channel MOSFET. The reference is connected to the error amplifier’s inverting 6 input. The error amplifier compares this reference with the selected feedback voltage and amplifies the difference. The difference is conditioned and applied to the P-channel pass transistor’s gate. Operating Configurations The MAX710/MAX711 have several operating configurations to minimize noise and optimize efficiency for different input voltage ranges. These configurations are accomplished via the N/E input, which controls operation of the on-chip linear regulator. With N/E low, the linear regulator behaves as a 0.7Ω (at 5V output) PFET switch when the IC is boosting, and as a conventional linear regulator when VIN > VOUT. This provides optimum boost efficiency, but the PFET does little to reject boost-converter output ripple. With N/E high, boost ripple rejection is optimized by maintaining headroom (VFV, typically 0.5V at 5V output) across the linear regulator. Boost mode efficiency is then about 10% lower than with N/E high. _______________________________________________________________________________________ 3.3V/5V or Adjustable, Step-Up/Down DC-DC Converters VOUT VIN ERROR AMP2 REF1 MAX710/MAX711 N/E PS LX ∆tON FIXED tOFF GENERATOR VFV DRV N OFF PS ILIM 100mV MAX710 CURRENTLIMIT COMPARATOR PGND ERROR AMP1 REF1 PGND PS REF2 OUT (FB) SHDN REFA REF2 REF STBY 3.3/5 REFB REF1 GND LBI+ LBI- LBO ( ) IS FOR MAX711. Figure 1. Functional Diagram _______________________________________________________________________________________ 7 MAX710/MAX711 3.3V/5V or Adjustable, Step-Up/Down DC-DC Converters In high-efficiency mode (N/E = low), the maximum input voltage is limited to 7V. This voltage limitation is easily overcome, however, by configuring the LBO output to change modes based on input voltage, allowing an 11V maximum input with high-efficiency configurations. Four operating configurations are described in Table 1 and in the following subsections. Configuration 1: High Efficiency, 7V Max VIN With N/E connected to GND, when the IC boosts, the linear regulator operates only as a switch, with minimum forward drop, until VIN > VOUT (where linear regulation begins). This configuration is limited to no more than 7V input, but provides best efficiency for batteryonly operation or low-voltage AC adapter usage. Table 1. Operating Configurations Configuration 2: High Efficiency, VBATT < VOUT In this configuration, N/E is driven high by LBO when V IN > V OUT (Figure 2a). When V IN < V OUT , the IC boosts, and the linear regulator operates as a switch, with minimum forward drop. When VIN > VOUT, the linear regulator operates with VFV forward drop, while VPS increases by VFV so that OUT maintains regulation. VFV is set inside the IC to approximately 0.5V (at 5V VOUT). When VIN is only slightly higher than VOUT, conversion efficiency is poorer than in configuration 1, so configuration 2 is most suitable when the battery voltage is less than VOUT, but the AC adapter output is greater than VOUT. NO. DESCRIPTION INPUT VOLTAGE CONNECTIONS 1 High efficiency, 7V max VIN Up to 7V N/E = GND 2 High efficiency, VBATT < VOUT (Figure 2a) Up to 11V LBO = N/E LBI- = VOUT LBI+ = VIN 3 High efficiency, 11V, VBATT < 6.5V (Figure 2b) Up to 11V LBO = N/E LBI- = REF LBI+ = R5, R6 4 Low noise Up to 11V N/E = PS VIN = +1.8V TO +11V VIN = +1.8V TO +11V 100µF 100µF L1 SHDN LX STBY PS LBO 100µF OUT N/E L1 R5 4.7µF SHDN LX STBY PS OUT N/E LBO MAX710 4.7µF MAX710 LBI+ LBI+ LBI- R6 REF REF 3/5 PGND GND ILIM LBI- 0.1µF 3/5 PGND GND ILIM 0.1µF Figure 2a. High-Efficiency Operating Configuration for VBATT < VOUT 8 100µF (VIN - VREF) VREF R5 = R6 (4.08) WHEN VREF = 1.28V AND VIN = 6.5V R5 = R6 Figure 2b. High-Efficiency Operating Configuration for VBATT < 6.5V _______________________________________________________________________________________ 3.3V/5V or Adjustable, Step-Up/Down DC-DC Converters Configuration 4: Low Noise With N/E connected to PS, when the IC is boosting, the linear regulator operates with VFV forward voltage (typically 0.5V at 5V VOUT) for optimum noise rejection. Linear regulation occurs when VIN > VOUT + VFV. The VFV voltage differential results in boost efficiency typically 10% lower than with the high-efficiency configurations. IN C1 L1 ON OFF R3 SHDN LX STBY PS OUT N/E LBO R1 MAX711 LBI+ R4 C2 C4 FB LBIR2 REF PGND GND ILIM Figure 3. MAX711 Adjustable Output Voltage ILIM The current-limit-select input, ILIM, selects between the two peak current limits: 1.5A (ILIM = GND) and 0.8A (ILIM = PS). If the application requires 200mA or less from the MAX710/MAX711, select 0.8A. The lower peak current limit permits the use of smaller, low-cost inductors. The ILIM input is internally diode clamped to GND and PS, and should not be connected to signals outside this range. Shutdown and Standby Modes Grounding SHDN turns off the MAX710/MAX711 completely, disconnecting the input from the output. Tie SHDN to PS for normal operation. The MAX710/MAX711 have a standby mode that shuts down the step-up converter. The linear regulator remains on with a 7µA (typ) LDO quiescent current. Connect STBY to ground to enter standby mode; otherwise, connect STBY to PS. __________________Design Procedure Output Voltage Selection For the MAX710, you can obtain a 3.3V or 5V output voltage by tying 3/5 to GND or PS. Efficiency is typically 85% over a 2mA to 250mA load range. The device is bootstrapped, with power derived from the step-up voltage output (at PS). Under all load conditions, the MAX710/MAX711 typically start up with a 1V input. If the battery voltage exceeds the programmed output voltage, the output will linear regulate down to the selected output voltage. The MAX711’s adjustable output voltage is set by two resistors, R1 and R2 (Figure 3), which form a voltage divider between the output and FB. Use the following equation to determine the resistor values: R1 = R2 [(VOUT / VREF) - 1] where VREF = 1.25V. Since the input bias current at FB has a maximum value of 50nA, R1 and R2 can be large with no significant accuracy loss. Choose R2 in the 100kΩ to 1MΩ range and calculate R1 using the formula above. For 1% error, the current through R1 should be at least 100 times FB’s bias current. Low-Battery Comparator The MAX710/MAX711 contain a comparator for lowbattery detection. If the voltage at LBI+ falls below that at LBI- (typically connected to REF), LBO goes low. Hysteresis is typically 50mV. Set the low-battery monitor’s threshold with two resistors, R3 and R4 (Figure 2), using the following equation: R3 = R4 [(VLBT / VLBI-) - 1] _______________________________________________________________________________________ 9 MAX710/MAX711 Configuration 3: High Efficiency, 11V, VBATT < 6.5V In this configuration, N/E is driven high by LBO when V IN > 6.5V (Figure 2b). When V IN < V OUT , the IC boosts, and the linear regulator operates as a switch, with minimum forward drop. When VIN > VOUT, linear regulation begins. When VIN > 6.5V (set by R5 and R6), the linear regulator forces a minimum forward drop of VFV (typically 0.5V at 5V VOUT) as LBO drives N/E high. This transition is not seen at the output, since the linear regulator already has an input-output voltage difference of 6.5V - 5V. Efficiency with VIN slightly higher than VOUT is equal to that of configuration 1, so configuration 3 is most suitable when the battery voltage may be near VOUT. This hookup has no functional shortcomings compared with configuration 2, except that two additional resistors (R5 and R6) are needed. MAX710/MAX711 3.3V/5V or Adjustable, Step-Up/Down DC-DC Converters Table 2. Component Selection INDUCTORS (L1) CAPACITORS RECTIFIERS (D1) Sumida CD75-220 (1.5A), CDRH-74-220 (1.23A), or CD54-220 100µF, 16V low-ESR tantalum capacitor AVX TPSE107M016R0100 or Sprague 593D107X0016E2W Coilcraft DO33-08P-223 4.7µF, 16V tantalum capacitor Sprague 595D475X0016A2T where VLBT is the desired threshold of the low-battery detector and VLBI- is the voltage applied to the inverting input of the low-battery comparator. Since LBI current is less than 50nA, R3 and R4 can be large (typically 100kΩ to 1MΩ), minimizing input supply loading. If the low-battery comparator is not used, connect LBI+ to PS and LBI- to REF, leaving LBO unconnected. Inductor Selection A 22µH inductor value performs well in most MAX710/MAX711 applications. The inductance value is not critical, however, since the MAX710/MAX711 work with inductors in the 18µH to 100µH range. Smaller inductance values typically offer a smaller size for a given series resistance, allowing the smallest overall circuit dimensions. Circuits using larger inductance values exhibit higher output current capability and larger physical dimensions for a given series resistance. The inductor’s incremental saturation current rating should be greater than the peak switch-current limit, which is 1.5A for ILIM = GND and 0.8A for ILIM = PS. However, it is generally acceptable to bias most inductors into saturation by as much as 20%, although this slightly reduces efficiency. The inductor’s DC resistance significantly affects efficiency. See Tables 2 and 3 for a list of suggested inductors and suppliers. Capacitor Selection A 100µF, 16V, 0.1Ω equivalent series resistance (ESR), surface-mount tantalum (SMT) output filter capacitor, C2, typically exhibits 50mV output ripple when stepping up from 2V to 5V at 100mA. Smaller capacitors (down to 10µF with higher ESRs) are acceptable for light loads or in applications that can tolerate higher output ripple. The ESR of both bypass and filter capacitors affects efficiency and output ripple. Output voltage ripple is the product of the peak inductor current and the output capacitor’s ESR. Use low-ESR capacitors for best performance, or connect two or more filter capacitors in parallel. Low-ESR, SMT capacitors are currently available from Sprague (595D series) and AVX (TPS series). Sanyo OS-CON organic-semiconductor through-hole capacitors also exhibit very low ESR and are especially 10 Schottky diode Motorola MBRS130T3 useful for operation at cold temperatures. The output capacitor, C3, needs to be only 4.7µF to maintain linear regulator stability. See Tables 2 and 3 for a list of suggested capacitors and suppliers. Rectifier Diode For optimum performance, use a switching Schottky diode. Refer to Tables 2 and 3 for the suggested diode and supplier. __________Applications Information The MAX710/MAX711 high-frequency operation makes PC layout important for minimizing ground bounce and noise. Keep the IC’s GND pin and the ground leads of C1 and C2 (Figure 1) less than 0.2in. (5mm) apart. Also keep all connections to the FB and LX pins as short as possible. To maximize output power and efficiency and minimize output ripple voltage, use a ground plane and solder the IC’s GND pin directly to the ground plane. Table 3. Component Suppliers SUPPLIER PHONE FAX AVX (803) 946-0690 (803) 626-3123 Coilcraft (847) 639-6400 (847) 639-1469 Motorola (602) 303-5454 (602) 994-6430 Sanyo (619) 661-6835 (619) 661-1055 Sprague (603) 224-1961 (603) 224-1430 Sumida (847) 956-0666 (847) 956-0702 ___________________Chip Information TRANSISTOR COUNT: 661 SUBSTRATE CONNECTED TO GND ______________________________________________________________________________________ 3.3V/5V or Adjustable, Step-Up/Down DC-DC Converters SOICN.EPS ______________________________________________________________________________________ 11 MAX710/MAX711 ________________________________________________________Package Information MAX710/MAX711 3.3V/5V or Adjustable, Step-Up/Down DC-DC Converters NOTES 12 ______________________________________________________________________________________