MAXIM MAX9268GCM/V+

19-5211; Rev 2; 1/11
TION KIT
EVALUA BLE
AVAILA
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
Features
The MAX9268 deserializer utilizes Maxim’s gigabit
multimedia serial link (GMSL) technology. The MAX9268
deserializer features an LVDS system interface for reduced
pin count and a smaller package, and pairs with any GMSL
serializer to form a complete digital serial link for joint
transmission of high-speed video, audio, and bidirectional
control data.
S Pairs with Any GMSL Serializer
The MAX9268 allows a maximum serial payload data
rate of 2.5Gbps for a 15m shielded twisted-pair (STP)
cable. The deserializer operates up to a maximum
output clock rate of 104MHz (3-channel LVDS) or 78MHz
(4-channel LVDS). This serial link supports display
panels from QVGA (320 x 240) to WXGA (1280 x 800) and
higher with 24-bit color.
S 4-Bit to 32-Bit Word Length, 8kHz to 192kHz I2S
The 3-channel mode outputs an LVDS clock, three lanes
of LVDS data (21 bits), UART control signals, and one I2S
audio channel consisting of three signals. The 4-channel
mode outputs an LVDS clock, four lanes of LVDS data
(28 bits), UART control signals, an I2S audio channel,
and auxiliary control outputs. The three audio outputs
form a standard I2S interface, supporting sample rates
from 8kHz to 192kHz and audio word lengths of 4 to 32
bits. The embedded control channel forms a full-duplex,
differential, 100kbps to 1Mbps UART link between the
serializer and deserializer. An electronic control unit (ECU),
or microcontroller (FC), can be located on the serializer
side of the link (typical for video display), on the MAX9268
side of the link (typical for image sensing), or on both sides.
In addition, the control channel enables ECU/FC control of
peripherals on the remote side, such as backlight control,
grayscale gamma correction, camera module, and touch
screen. Base-mode communication with peripherals uses
either I2C or the GMSL UART format. In addition, the
MAX9268 features a bypass mode that enables full-duplex
communication using custom UART formats.
The GMSL serializer driver preemphasis, along with the
MAX9268 channel equalizer, extends the link length and
enhances the link reliability. Spread spectrum is available
to reduce EMI on the LVDS and control outputs of the
MAX9268. The serial line inputs comply with ISO 10605 and
IEC 61000-4-2 ESD protection standards.
The core supply for the MAX9268 is 3.3V. The I/O supply
ranges from 1.8V to 3.3V. The MAX9268 is available in
a 48-pin TQFP package (7mm x 7mm) with an exposed
pad, and is specified over the -40NC to +105NC automotive
temperature range.
S 2.5Gbps Payload-Rate AC-Coupled Serial Link
S Scrambled 8b/10b Line Coding
S Supports WXGA (1280 x 800) with 24-Bit Color
S 8.33MHz to 104MHz (3-Channel LVDS) or 6.25MHz
to 78MHz (4-Channel LVDS) Output Clock
Audio Channel Supports High-Definition Audio
S Embedded Half-/Full-Duplex Bidirectional Control
Channel (100kbps to 1Mbps)
S Two 3-Level Inputs Support 9 Device Addresses
S Interrupt Supports Touch-Screen Functions for
Display Panels
S I2C Master for Peripherals
S Equalizer for Serial Link Input
S Programmable Spread Spectrum on the LVDS and
Control Outputs for Reduced EMI
S Serial-Data Clock Recovery Eliminates an External
Clock
S Automatic Data-Rate Detection Allows On-the-Fly
Data-Rate Change
S Built-In PRBS Generator for BER Testing of the
Serial Link
S ISO 10605 and IEC 61000-4-2 ESD Protection
S -40NC to +105NC Operating Temperature Range
S 1.8V to 3.3V I/O and 3.3V Core Supplies
S Patent Pending
Ordering Information
PART
TEMP RANGE
PIN-PACKAGE
MAX9268GCM/V+
-40NC to +105NC
48 TQFP-EP*
MAX9268GCM/V+T
-40NC to +105NC
48 TQFP-EP*
/V denotes an automotive qualified product.
+Denotes a lead(Pb)-free/RoHS-compliant package.
*EP = Exposed pad.
T = Tape and reel.
Applications
High-Resolution Automotive Navigation
Rear-Seat Infotainment
Megapixel Camera Systems
________________________________________________________________ Maxim Integrated Products 1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
MAX9268
General Description
MAX9268
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
ABSOLUTE MAXIMUM RATINGS
AVDD to AGND.....................................................-0.5V to +3.9V
DVDD, IOVDD to AGND........................................-0.5V to +3.9V
GND to AGND.......................................................-0.5V to +0.5V
IN+, IN- to AGND..................................................-0.5V to +1.9V
TXOUT__, TXCLKOUT_ to AGND.........................-0.5V to +3.9V
All Other Pins to GND.......................... -0.5V to (VIOVDD + 0.5V)
TXOUT__, TXCLKOUT_ Short Circuit to Ground
or Supply................................................................Continuous
Continuous Power Dissipation (TA = +70°C)
48-Pin TQFP (derate 36.2mW/°C above +70°C).....2898.6mW
Human Body Model (RD = 1.5kΩ, CS = 100pF)
(IN+, IN-) to AGND...........................................................±8kV
(TXOUT__, TXCLKOUT_) to AGND..................................±8kV
All Other Pins to GND....................................................±3.5kV
IEC 61000-4-2 (RD = 330Ω, CS = 150pF)
Contact Discharge
(IN+, IN-) to AGND...................................................±10kV
(TXOUT__, TXCLKOUT_) to AGND.............................±8kV
Air Discharge
(IN+, IN-) to AGND.........................................................±12kV
(TXOUT__, TXCLKOUT_) to AGND................................±20kV
ISO 10605 (RD = 2kΩ, CS = 330pF)
Contact Discharge
(IN+, IN-) to AGND...........................................................±8kV
(TXOUT__, TXCLKOUT_) to AGND..................................±8kV
Air Discharge
(IN+, IN-) to AGND.........................................................±15kV
(TXOUT__, TXCLKOUT_) to AGND................................±30kV
Operating Temperature Range......................... -40°C to +105°C
Junction Temperature......................................................+150°C
Storage Temperature Range............................. -65°C to +150°C
Lead Temperature (soldering, 10s).................................+300°C
Soldering Temperature (reflow).......................................+260°C
PACKAGE THERMAL CHARACTERISTICS (Note 1)
48 TQFP
Junction-to-Ambient Thermal Resistance (BJA)........27.6°C/W
Junction-to-Case Thermal Resistance (BJC).................2°C/W
Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a fourlayer board. For detailed information on package thermal considerations, refer to www.maxim-ic.com/thermal-tutorial.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
(VAVDD = VDVDD = 3.0V to 3.6V, VIOVDD = 1.7V to 3.6V, RL = 100Ω Q1% (differential), TA = -40NC to +105NC, unless otherwise noted.
Typical values are at VAVDD = VDVDD = VIOVDD = 3.3V, TA = +25NC.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
SINGLE-ENDED INPUTS (BWS, INT, CDS, EQS, MS, PWDN, SSEN, DRS)
High-Level Input Voltage
VIH1
Low-Level Input Voltage
VIL1
Input Current
IIN1
Input Clamp Voltage
VCL
0.65 x
VIOVDD
VIN = 0V to VIOVDD
ICL = -18mA
V
-10
0.35 x
VIOVDD
V
+10
FA
-1.5
V
SINGLE-ENDED OUTPUTS (WS, SCK, SD/CNTL0, CNTL1, CNTL2/MCLK)
High-Level Output Voltage
Low-Level Output Voltage
Output Short-Circuit Current
VOH1
VOL1
IOS
DCS = 0
VIOVDD
- 0.3
DCS = 1
VIOVDD
- 0.2
IOUT = -2mA
IOUT = 2mA
V
DCS = 0
0.3
DCS = 1
0.2
VOUT = VGND,
DCS = 0
VIOVDD = 3.0V to 3.6V
15
25
39
VIOVDD = 1.7V to 1.9V
3
7
13
VOUT = VGND,
DCS = 1
VIOVDD = 3.0V to 3.6V
20
35
63
VIOVDD = 1.7V to 1.9V
5
10
21
2 _______________________________________________________________________________________
V
mA
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
(VAVDD = VDVDD = 3.0V to 3.6V, VIOVDD = 1.7V to 3.6V, RL = 100Ω Q1% (differential), TA = -40NC to +105NC, unless otherwise noted.
Typical values are at VAVDD = VDVDD = VIOVDD = 3.3V, TA = +25NC.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
I2C AND UART I/O, OPEN-DRAIN OUTPUTS (RX/SDA, TX/SCL, LOCK, ERR, GPIO_)
High-Level Input Voltage
VIH2
Low-Level Input Voltage
VIL2
Input Current
IIN2
Low-Level Output Voltage
VOL2
0.7 x
VIOVDD
V
0.3 x
VIOVDD
VIN = 0V to
VIOVDD (Note 2)
IOUT = 3mA
RX/SDA, TX/SCL
-110
+1
LOCK, ERR, GPIO_
VIOVDD = 1.7V to 1.9V
-80
+1
0.4
VIOVDD = 3.0V to 3.6V
0.3
V
FA
V
DIFFERENTIAL OUTPUT FOR REVERSE CONTROL CHANNEL (IN+, IN-)
Differential High Output Peak
Voltage, (VIN+) - (VIN-)
VROH
No high-speed data transmission
(Figure 1)
30
60
mV
Differential Low Output Peak
Voltage, (VIN+) - (VIN-)
VROL
No high-speed data transmission
(Figure 1)
-60
-30
mV
90
mV
DIFFERENTIAL INPUTS (IN+, IN-)
Differential High Input Threshold
(Peak) Voltage, (VIN+) - (VIN-)
VIDH(P)
Figure 2
Differential Low Input Threshold
(Peak) Voltage, (VIN+) - (VIN-)
VIDL(P)
Figure 2
Input Common-Mode Voltage
((VIN+) + (VIN-))/2
Differential Input Resistance
(Internal)
40
-90
-40
mV
VCMR
1
1.3
1.6
V
RI
80
100
130
I
THREE-LEVEL LOGIC INPUTS (ADD0, ADD1)
High-Level Input Voltage
VIH
Low-Level Input Voltage
VIL
Mid-Level Input Current
IINM
0.7 x
VIOVDD
V
0.3 x
VIOVDD
V
ADD0 and ADD1 open or connected
to a driver with output in high impedance
(Note 3)
-10
+10
FA
-150
+150
FA
-1.5
V
450
mV
25
mV
1.375
V
25
mV
Input Current
IIN
ADD0 and ADD1 = high or low,
PWDN = high or low
Input Clamp Voltage
VCL
ICL = -18mA
LVDS OUTPUTS (TXOUT__, TXCLKOUT_)
Differential Output Voltage
Change in VOD Between
Complementary Output States
Output Offset Voltage
Change in VOS Between
Complementary Output States
VOD
Figure 3
DVOD
Figure 3
VOS
Figure 3
DVOS
Figure 3
250
1.125
_______________________________________________________________________________________ 3
MAX9268
DC ELECTRICAL CHARACTERISTICS (continued)
MAX9268
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
DC ELECTRICAL CHARACTERISTICS (continued)
(VAVDD = VDVDD = 3.0V to 3.6V, VIOVDD = 1.7V to 3.6V, RL = 100Ω Q1% (differential), TA = -40NC to +105NC, unless otherwise noted.
Typical values are at VAVDD = VDVDD = VIOVDD = 3.3V, TA = +25NC.)
PARAMETER
Output Short-Circuit Current
SYMBOL
IOS
Magnitude of Differential Output
Short-Circuit Current
IOSD
Output High-Impedance Current
IOZ
CONDITIONS
VOUT = 0V or 3.6V
MIN
TYP
MAX
3.5mA LVDS output
-7.5
+7.5
7mA LVDS output
-15
+15
3.5mA LVDS output
7.5
7mA LVDS output
15
ADD0 and ADD1 = high or low,
PWDN = high or low
-0.5
+0.5
UNITS
mA
mA
FA
POWER SUPPLY
Worst-Case Supply Current
(Figure 4)
IWCS
Sleep-Mode Supply Current
ICCS
Power-Down Current
ICCZ
BWS = low, fTXCLKOUT_ = 16.6MHz
142
180
BWS = low, fTXCLKOUT_ = 33.3MHz
BWS = low, fTXCLKOUT_ = 66.6MHz
153
200
179
240
BWS = low, fTXCLKOUT_ = 104MHz
212
280
80
130
FA
19
70
FA
PWDN = GND
mA
AC ELECTRICAL CHARACTERISTICS
(VAVDD = VDVDD = 3.0V to 3.6V, VIOVDD = 1.7V to 3.6V, RL = 100Ω Q1% (differential), TA = -40NC to +105NC, unless otherwise noted.
Typical values are at VAVDD = VDVDD = VIOVDD = 3.3V, TA = +25NC.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
LVDS CLOCK OUTPUTS (TXCLKOUT+, TXCLKOUT-)
Clock Frequency
fTXCLKOUT_
BWS = GND, VDRS = VIOVDD
BWS = GND, DRS = GND
8.33
16.66
16.66
104
VBWS = VIOVDD, VDRS = VIOVDD
6.25
12.5
VBWS = VIOVDD, DRS = GND
12.5
78
MHz
I2C/UART PORT TIMING
Output Rise Time
tR
30% to 70%, CL = 10pF to 100pF,
1kI pullup to IOVDD (Figure 5)
20
150
ns
Output Fall Time
tF
70% to 30%, CL = 10pF to 100pF,
1kI pullup to IOVDD (Figure 5)
20
150
ns
Input Setup Time
tSET
I2C only (Figure 5)
100
ns
Input Hold Time
tHOLD
I2C only (Figure 5)
0
ns
SWITCHING CHARACTERISTICS
CNTL_ Output Rise-and-Fall Time
tR, tF
LVDS Output Rise Time
tR
LVDS Output Fall Time
tF
20% to 80%, CL
= 10pF, DCS = 1
(Figure 6)
VIOVDD = 1.7V to 1.9V
0.5
3.1
VIOVDD = 3.0V to 3.6V
0.3
2.2
20% to 80%, CL
= 5pF, DCS = 0
(Figure 6)
VIOVDD = 1.7V to 1.9V
0.6
3.8
VIOVDD = 3.0V to 3.6V
0.4
2.4
20% to 80%, RL = 100I (Figure 3)
80% to 20%, RL = 100I (Figure 3)
ns
200
350
ps
200
350
ps
4 _______________________________________________________________________________________
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
(VAVDD = VDVDD = 3.0V to 3.6V, VIOVDD = 1.7V to 3.6V, RL = 100Ω Q1% (differential), TA = -40NC to +105NC, unless otherwise noted.
Typical values are at VAVDD = VDVDD = VIOVDD = 3.3V, TA = +25NC.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
N/7 x tCLK N/7 x N/7 x tCLK
fTXCLKOUT_ = 12.5MHz
- 250
tCLK
+ 250
LVDS Output Pulse Position
tPPOSN
N = 0 to 6, tCLK =
fTXCLKOUT_ = 33MHz
1/fTXCLKOUT_,
fTXCLKOUT_ =
104MHz
fTXCLKOUT_ = 78MHz
(Figure 7)
fTXCLKOUT_ = 104MHz
N/7 x tCLK N/7 x N/7 x tCLK
- 200
tCLK
+ 200
N/7 x tCLK N/7 x N/7 x tCLK
- 125
tCLK
+ 125
ps
N/7 x tCLK N/7 x N/7 x tCLK
- 100
tCLK
+ 100
LVDS Output Enable Time
tLVEN
From the last bit of the enable UART
packet to VOS = 1125mV
100
Fs
LVDS Output Disable Time
tLVDS
From the last bit of the enable UART
packet to VOS = 0V
100
Fs
3540
Bits
Deserializer Delay
tSD
Figure 8 (Note 4)
Reverse Control-Channel Output
Rise Time
tR
No forward-channel data transmission
(Figure 1)
180
400
ns
Reverse Control-Channel Output
Fall Time
tF
No forward-channel data transmission
(Figure 1)
180
400
ns
Lock Time
Power-Up Time
I2S OUTPUT TIMING
WS Jitter
tLOCK
Figure 9
3.6
ms
tPU
Figure 10
4.1
ms
tAJ-WS
SCK Jitter
tAJ-SCK
Audio Skew Relative to Video
tASK
fWS = 48kHz or 44.1kHz
0.4e-3
x tWS
0.5e-3
x tWS
fWS = 96kHz
0.8e-3
x tWS
1e-3
x tWS
fWS = 192kHz
1.6e-3
x tWS
2e-3
x tWS
nWS = 16 bits, fWS =
48kHz or 44.1kHz
13e-3
x tSCK
16e-3
x tSCK
nWS = 24 bits, fWS =
96kHz
nWS = 32 bits,
fWS = 192kHz
Video and audio synchronized
39e-3
x tSCK
0.1
x tSCK
3 x tWS
48e-3
x tSCK
0.13
x tSCK
4 x tWS
tWS = 1/fWS,
rising (falling)
edge to falling
(rising) edge
(Note 5)
tSCK = 1/fSCK,
rising edge to
rising edge
CL = 10pF, DCS = 1
0.3
3.1
CL = 5pF, DCS = 0
0.4
3.8
ns
ns
Fs
SCK, SD, WS Rise-and-Fall Time
tR, tF
20% to 80%
ns
SD, WS Valid Time Before SCK
tDVB
tSCK = 1/fSCK (Figure 11)
0.35 x
tSCK
0.5 x
tSCK
ns
SD, WS Valid Time After SCK
tDVA
tSCK = 1/fSCK (Figure 11)
0.35 x
tSCK
0.5 x
tSCK
ns
Note 2: Minimum IIN due to voltage drop across the internal pullup resistor.
Note 3: Measured in serial link bit times. Bit time = 1/(30 x fTXCLKOUT_) for BWS = GND. Bit time = 1/(40 x fTXCLKOUT_) for VBWS =
VIOVDD.
Note 4: Rising to rising-edge jitter can be twice as large.
_______________________________________________________________________________________ 5
MAX9268
AC ELECTRICAL CHARACTERISTICS (continued)
Typical Operating Characteristics
(VAVDD = VDVDD = VIOVDD = 3.3V, TA = +25NC, unless otherwise noted.)
180
170
160
190
180
170
160
150
140
140
25
45
65
85
105
0% SPREAD
-30
-40
-50
-60
-70
-80
2% SPREAD
-90
4% SPREAD
-100
5
20
35
50
65
80
30.5
31.5
32.5
33.5
34.5
35.5
TXCLKOUT_ FREQUENCY (MHz)
OUTPUT POWER SPECTRUM
vs. TXCLKOUT_ FREQUENCY
(VARIOUS MAX9268 SPREAD)
MAXIMUM TXCLKOUT_ FREQUENCY
vs. STP CABLE LENGTH (BER < 10-9)
MAXIMUM TXCLKOUT_ FREQUENCY
vs. ADDITIONAL DIFFERENTIAL
CL (BER < 10-9)
-40
-50
-60
-70
-80
-90
2% SPREAD
4% SPREAD
80
OPTIMUM
PE/EQ SETTINGS
60
NO PE, 10.7dB
EQUALIZATION
40
NO PE, 5.2dB
EQUALIZATION
20
BER CAN BE AS LOW AS 10-12 FOR
CABLE LENGTHS LESS THAN 10m
0
-100
63
65
67
69
TXCLKOUT_ FREQUENCY (MHz)
71
10m STP CABLE
100
OPTIMUM
PE/EQ SETTINGS
80
60
NO PE, 10.7dB
EQUALIZATION
40
NO PE, 5.2dB EQUALIZATION
20
BER CAN BE AS LOW AS 10-12 FOR CL < 4pF
FOR OPTIMUM PE/EQ SETTINGS
0
0
5
10
15
STP CABLE LENGTH (m)
20
MAX9268 toc06
100
120
MAXIMUM TXCLKOUT_ FREQUENCY (MHz)
0% SPREAD
120
MAXIMUM TXCLKOUT_ FREQUENCY (MHz)
fTXCLKOUT_ = 66MHz
MAX9268 toc03
fTXCLKOUT_ = 33MHz
-20
TXCLKOUT_ FREQUENCY (MHz)
-20
61
-10
TXCLKOUT_ FREQUENCY (MHz)
-10
-30
MAX9268 toc02
200
150
5
PRBS PATTERN
ALL EQUALIZER MODES
ALL SPREAD MODES
MAX9268 toc05
190
210
TOTAL SUPPLY CURRENT (mA)
MAX9268 toc01
PRBS PATTERN
ALL EQUALIZER MODES
ALL SPREAD MODES
MAX9268 toc04
TOTAL SUPPLY CURRENT (mA)
210
200
OUTPUT POWER SPECTRUM
vs. TXCLKOUT_ FREQUENCY
(VARIOUS MAX9268 SPREAD)
TOTAL SUPPLY CURRENT
vs. TXCLKOUT_ FREQUENCY
(4-CHANNEL MODE)
OUTPUT POWER SPECTRUM (dBm)
TOTAL SUPPLY CURRENT
vs. TXCLKOUT_ FREQUENCY
(3-CHANNEL MODE)
OUTPUT POWER SPECTRUM (dBm)
MAX9268
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
0
2
4
6
8
10
ADDITIONAL DIFFERENTIAL LOAD CAPACITANCE (pF)
6 _______________________________________________________________________________________
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
TXOUT3+
TXCLKOUTTXCLKOUT+
TXOUT3-
TXOUT2TXOUT2+
AGND
TXOUT1TXOUT1+
AVDD
TXOUT0TXOUT0+
TOP VIEW
36 35 34 33 32 31 30 29 28 27 26 25
AGND
GND
37
24
38
23
IOVDD
ADD0
39
22
40
21
ADD1
LOCK
ERR
MS
SSEN
DRS
AVDD
AGND
41
20
42
19
MAX9268
43
18
44
17
45
16
46
15
47
14
EP
13
+
7
8
GND
IOVDD
CNTL2/MCLK
CNTL1
SD/CNTL0
SCK
WS
PWDN
TX/SCL
RX/SDA
9 10 11 12
GND
6
EQS
GPIO1
DVDD
5
INAGND
4
IN+
3
AVDD
2
BWS
INT
1
CDS
GPIO0
48
AGND
AVDD
TQFP
Pin Description
PIN
NAME
FUNCTION
Bus-Width Select. Output width selection requires external pulldown or pullup resistor. Set
BWS = low for 3-channel mode. Set BWS = high for 4-channel mode.
1
BWS
2
INT
Interrupt Input. Requires external pulldown or pullup resistor. A transition on the MAX9268’s
INT input toggles the GMSL serializer’s INT output.
3
CDS
Control Direction Selection. Control link direction selection input requires external pulldown or
pullup resistor. Set CDS = low for FC on the GMSL serializer side of the serial link. Set CDS =
high for FC on the MAX9268 side of the serial link.
4
GPIO0
General-Purpose I/O 0. Open-drain, general-purpose input/output with internal 60kI (typ)
pullup resistor to IOVDD. GPIO0 is high impedance during power-up and when PWDN = low.
5, 23, 32, 47
AVDD
3.3V Analog Power Supply. Bypass AVDD to AGND with 0.1FF and 0.001FF capacitors as
close as possible to the device with the smaller capacitor closest to AVDD.
6, 7
IN+, IN-
8, 24, 31, 37, 48
AGND
9
EQS
Differential CML Input. Differential input of the serial link.
Analog Ground
Equalizer Select Input. EQS requires external pulldown or pullup resistor. The state of EQS
latches upon power-up or when resuming from power-down mode (PWDN = low). Set
EQS = low for 10.7dB equalizer boost (EQTUNE = 1001). Set EQS = high for 5.2dB
equalizer boost (EQTUNE = 0100).
_______________________________________________________________________________________ 7
MAX9268
Pin Configuration
MAX9268
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
Pin Description (continued)
PIN
NAME
FUNCTION
10
GPIO1
General-Purpose I/O 1. Open-drain general-purpose input/output with internal 60kI (typ)
pullup resistor to IOVDD. GPIO1 is high impedance during power-up and when PWDN = low.
11
DVDD
3.3V Digital Power Supply. Bypass DVDD to GND with 0.1FF and 0.001FF capacitors as close
as possible to the device with the smaller capacitor closest to DVDD.
12, 22, 38
GND
Digital and I/O Ground
13
RX/SDA
Receive/Serial Data. UART receive or I2C serial-data input/output with internal 30kI (typ)
pullup to IOVDD. In UART mode, RX/SDA is the Rx input of the MAX9268’s UART. In I2C
mode, RX/SDA is the SDA input/output of the MAX9268’s I2C master.
14
TX/SCL
Transmit/Serial Clock. UART transmit or I2C serial-clock output with internal 30kI (typ) pullup
to IOVDD. In UART mode, TX/SCL is the Tx output of the MAX9268’s UART. In I2C mode, TX/
SCL is the SCL output of the MAX9268’s I2C master.
15
PWDN
Power-Down. Active-low power-down input requires external pulldown or pullup resistor.
16
WS
I2S Word-Select Output
17
SCK
I2S Serial-Clock Output
18
SD/CNTL0
I2S Serial-Data/Control Output. Disable I2S to use SD/CNTL0 as an additional control output.
19
CNTL1
Control Output 1. CNTL1 is not active in 3-channel mode and remains low. To use CNTL1,
drive BWS high (4-channel mode) and set DISCNTL = 0. CNTL1 is mapped from DOUT27.
Control 2/MCLK Output. CNTL2/MCLK is not active in 3-channel mode and remains low.
To use CNTL2/MCLK, drive BWS high (4-channel mode). CNTL2/MCLK is mapped from
DOUT28. CNTL/MCLK can also be used to output MCLK (see the Additional MCLK Output for
Audio Applications section).
20
CNTL2/MCLK
21, 39
IOVDD
I/O Supply Voltage. 1.8V to 3.3V logic I/O power supply. Bypass IOVDD to GND with
0.1FF and 0.001FF capacitors as close as possible to the device with the smaller
capacitor closest to IOVDD.
25, 26, 29, 30,
33–36
TXOUT_+,
TXOUT_-
Differential LVDS Data Outputs. Set BWS = low (3-channel mode) to use TXOUT0_ to
TXOUT2_. Set BWS = high (4-channel mode) to use TXOUT0_ to TXOUT3_.
27, 28
TXCLKOUT+,
TXCLKOUT-
40
ADD0
Address Selection Input 0. Three-level input to select the MAX9268’s device address
(see Table 2). The state of ADD0 latches upon power-up or when resuming from power-down
mode (PWDN = low).
41
ADD1
Address Selection Input 1. Three-level input to select the MAX9268’s device address
(see Table 2). The state of ADD1 latches upon power-up or when resuming from power-down
mode (PWDN = low).
LOCK
Open-Drain Lock Output with Internal 60kI (typ) Pullup to IOVDD. LOCK = high indicates
PLLs are locked with correct serial-word-boundary alignment. LOCK = low indicates PLLs are
not locked or incorrect serial-word-boundary alignment. LOCK remains low when the
configuration link is active. LOCK is high impedance when PWDN = low.
ERR
Active-Low, Open-Drain Video Data Error Output with Internal 60kI (typ) Pullup to IOVDD.
ERR goes low when the number of decoding errors during normal operation exceeds a programmed error threshold, or when at least one PRBS error is detected during PRBS test. ERR
is high impendence when PWDN = low.
42
43
Differential LVDS Output for the LVDS Clock
8 _______________________________________________________________________________________
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
PIN
NAME
FUNCTION
MS
Mode Select. Control link mode-selection input requires an external pulldown or pullup resistor. Set MS = low to select base mode. Set MS = high to select bypass mode.
SSEN
Spread-Spectrum Enable. Serial link spread-spectrum enable input requires an external pulldown or pullup resistor. The state of SSEN latches upon power-up or when resuming from
power-down mode (PWDN = low). Set SSEN = high for Q2% spread spectrum on the LVDS
and control outputs. Set SSEN = low to use the LVDS and control outputs without spread
spectrum.
46
DRS
Data-Rate Select. Data-rate range-selection input requires an external pulldown or pullup resistor.
The state of DRS latches upon power-up or when resuming from power-down mode (PWDN =
low). Set DRS = high for TXCLKOUT_ frequencies of 8.33MHz to 16.66MHz (3-channel mode), or
6.25MHz to 12.5MHz (4-channel mode). Set DRS = low for TXCLKOUT_ frequencies of 16.66MHz
to 104MHz (3-channel mode), or 12.5MHz to 78MHz (4-channel mode).
—
EP
44
45
Exposed Pad. EP internally connected to AGND. MUST externally connect EP to the plane
supplying AGND for proper thermal and electrical performance.
Functional Diagram
IN+
TXCLKOUT+/-
CLK
DIV
SSPLL
CDR
PLL
Rx/EQ
IN-
7x PLL
TXOUT0+/-
RGB[17:0]
RGB
HS
HS
VS
TXOUT1+/PARALLEL
TO LVDS
VIDEO
DE
SERIAL
TO
PARALLEL
VS
DE
RGB[23:18] (4-CH)
TXOUT2+/-
RES/CNTL1
TXOUT3+/-
(4-CH)
FIFO
CNTL1/RES
8b/10b
DECODE/
UNSCRAMBLE
Tx
CNTL2
CNTL1
(4-CH)
REVERSE CONTROL
CHANNEL
ACB
AUDIO
FCC
CNTL2/MCLK
(4-CH)
MAX9268
UART/I2C
SD/CNTL0
SCK
WS
TX/SCL
RX/SDA
_______________________________________________________________________________________ 9
MAX9268
Pin Description (continued)
MAX9268
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
RL/2
IN+
MAX9268
VOD
REVERSE
CONTROL-CHANNEL
TRANSMITTER
VCMR
IN-
RL/2
IN+
IN-
IN-
IN+
VCMR
VROH
0.9 x VROH
(IN+) - (IN-)
0.1 x VROH
0.1 x VROL
tR
0.9 x VROL
VROL
tF
Figure 1. Reverse Control-Channel Output Parameters
RL/2
IN+
VID(P)
RL/2
VIN+
IN-
_
+
_
VIN-
+
_
CIN
CIN
VID(P) = | VIN+ - VIN- |
VCMR = (VIN+ + VIN-)/2
Figure 2. Test Circuit for Differential Input Measurement
10 ��
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
MAX9268
TXOUT_+
TXCLKOUT+
RL/2
VOD
VOS
TXOUT_-,
TXCLKOUT-
RL/2
((TXOUT_+) + (TXOUT_-))/2
((TXCLKOUT+) + (TXCLKOUT-))/2
TXOUT_TXCLKOUT-
GND
VOS(+)
VOS(-)
VOS(-)
TXOUT_+
TXCLKOUT+
DVOS = |VOS(+) - VOS(-)|
VOD(+)
VOD = 0V
VOD(-)
DVOD = |VOD(+) - VOD(-)|
tR
(TXOUT_+) - (TXOUT_-)
(TXCLKOUT+) - (TXCLKOUT-)
tF
VOD(-)
Figure 3. LVDS Output Parameters
TXCLKOUT+
TXCLKOUTTXOUT0+ TO TXOUT3+
TXOUT0- TO TXOUT3-
CNTL_
Figure 4. Worst-Case Pattern Output
tF
tR
TX/
SCL
tHOLD
tSET
RX/
SDA
P
S
S
P
Figure 5. I2C Timing Parameters
______________________________________________________________________________________ 11
MAX9268
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
(TXCLKOUT+) (TXCLKOUT-)
CL
(TXOUT_+) (TXOUT_-)
MAX9268
SINGLE-ENDED OUTPUT LOAD
tPPOS0
tPPOS1
0.8 x VI0VDD
tPPOS2
tPPOS3
tPPOS4
0.2 x VI0VDD
tPPOS5
tR
tF
tPPOS6
Figure 6. Single-Ended Output Rise-and-Fall Times
FIRST BIT
IN+/IN-
N
N+1
Figure 7. LVDS Output Pulse Position Measurement
IN+ - IN-
EXPANDED TIME SCALE
N+2...
FIRST BIT
N-1
N
TXOUT_+/
TXOUT_-
tLOCK
LOCK
TXCLKOUT+/-
VOH
tSD
PWDN MUST BE HIGH
Figure 8. Deserializer Delay
Figure 9. Lock Time
IN+/WS
PWDN
tDVA
VIH1
tR
tDVB
SCK
tPU
LOCK
tDVB
VOH
tDVA
SD
Figure 10. Power-Up Delay
Figure 11. Output I2S Timing Parameters
12 ��
tF
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
The MAX9268 deserializer with LVDS system interface utilizes Maxim’s GMSL technology. The MAX9268
deserializer pairs with any GMSL serializer to form a
complete digital serial link for joint transmission of highspeed video, audio, and bidirectional control data.
The MAX9268 allows a maximum serial payload data
rate of 2.5Gbps for greater than 15m of STP cable. The
deserializer operates up to 104MHz for 3-channel LVDS
or 78MHz for 4-channel LVDS. The operating frequency
range supports display panels from QVGA (320 x 240)
up to WXGA (1280 x 800) and higher with 24-bit color.
The 3-channel mode outputs an LVDS clock, three
lanes of LVDS data (21 bits), UART control signals,
and one I2S audio channel (consisting of three signals). The 4-channel mode outputs an LVDS clock, four
lanes of LVDS data (28 bits), UART control signals,
one I2S audio channel, and control signals. The I2S
interface supports sample rates from 8kHz to 192kHz
and audio word lengths of 4 to 32 bits. The embedded control channel forms a full-duplex, differential,
100kbps to 1Mbps UART link between the serializer and
deserializer. An ECU or FC can be located on the
serializer side of the link (typical for video display), on the
MAX9268 side of the link (typical for image sensing), or
on both sides. In addition, the control channel enables
ECU/FC control of peripherals in the remote side, such
as backlight control, grayscale Gamma correction,
camera module, and touch screen. Base-mode communication with peripherals uses either I2C or the GMSL
UART format. A bypass mode enables full-duplex communication using custom UART formats.
The MAX9268 channel equalizer, along with the
serializer preemphasis, extends the link length and
enhances the link reliability. Spread spectrum is available to reduce EMI on the LVDS and control outputs of
the MAX9268. The serial input complies with ISO 10605
and IEC 61000-4-2 ESD protection standards.
Register Mapping
The FC configures various operating conditions of the
GMSL serializer and the MAX9268 through internal
registers. The default device addresses are stored in registers 0x00 and 0x01 of both the GMSL serializer and the
MAX9268 (Table 1). Write to the 0x00 and 0x01 registers
in both devices to change the device address of the GMSL
serializer or the MAX9268.
Table 1. Power-Up Default Register Map (see Table 12)
REGISTER
ADDRESS
(hex)
POWER-UP
DEFAULT
(hex)
0x00
0x40, 0x44, 0x48
0x80, 0x84, 0x88,
0xC0, 0xC4, 0xC8
SERID = XX00XX0, serializer device address is determined by ADD1 and ADD0
(Table 2)
RESERVED = 0
0x01
0x50, 0x54, 0x58,
0x90, 0x94, 0x98,
0xD0, 0xD4, 0xD8
DESID =XX01XX0, deserializer device address is determined by ADD1 and ADD0
(Table 2)
RESERVED = 0
0x02
0x1F or 0x5F
0x03
0x00
POWER-UP DEFAULT SETTINGS
(MSB FIRST)
SS = 00 (SSEN = low), SS = 01 (SSEN = high), spread-spectrum settings depend on
SSEN pin state at power-up
RESERVED = 0
AUDIOEN = 1, I2S channel enabled
PRNG = 11, automatically detect the pixel clock range
SRNG = 11, automatically detect serial-data rate
AUTOFM = 00, calibrate spread-modulation rate only once after locking
RESERVED = 0
SDIV = 00000, autocalibrate sawtooth divider
______________________________________________________________________________________ 13
MAX9268
Detailed Description
MAX9268
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
Table 1. Power-Up Default Register Map (see Table 12) (continued)
REGISTER
ADDRESS
(hex)
0x04
0x05
POWER-UP
DEFAULT
(hex)
POWER-UP DEFAULT SETTINGS
(MSB FIRST)
0x03 or 0x13
LOCKED = 0, LOCK output is low (read only)
OUTENB = 0, outputs enabled
PRBSEN = 0, PRBS test disabled
SLEEP = 0 or 1, SLEEP setting default depends on CDS and MS pin state at power-up
(see the Link Startup Procedure section)
INTTYPE = 00, base mode uses I2C
REVCCEN = 1, reverse control channel active (sending)
FWDCCEN = 1, forward control channel active (receiving)
0x24 or 0x29
I2CMETHOD = 0, I2C master sends the register address
HPFTUNE = 01, 3.75MHz equalizer highpass cutoff frequency
PDHF = 0, high-frequency boosting disabled
EQTUNE = 0100 (EQS = high, 5.2dB), EQTUNE = 1001 (EQS = low, 10.7dB), EQTUNE
default setting depends on EQS pin state at power-up
0x06
0x0F
RESERVED = 0
AUTORST = 0, error registers/output autoreset disabled
DISINT = 0, INT transmission enabled
INT = 0, INT output is low (read only)
GPIO1OUT = 1, GPIO1 output set to high
GPIO1 = 1, GPIO1 input = high (read only)
GPIO0OUT = 1, GPIO0 output set to high
GPIO0 = 1, GPIO0 input = high (read only)
0x07
0x54
RESERVED = 01010100
0x08
0x30
RESERVED = 00110000
0x09
0xC8
RESERVED = 11001000
0x0A
0x12
RESERVED = 00010010
0x0B
0x20
RESERVED = 00100000
0x0C
0x00
ERRTHR = 00000000, error threshold set to zero for decoding errors
0x0D
0x00
(read only)
DECERR = 00000000, zero decoding errors detected
0x0E
0x00
(read only)
PRBSERR = 00000000, zero PRBS errors detected
0x12
0x00
MCLKSRC = 0, MCLK is derived from PCLK (see Table 5)
MCLKDIV = 0000000, MCLK output is disabled
0x13
0xX0
RESERVED = XXX
RESERVED = 10000
0x01
RESERVED = 00
FORCELVDS = 0, normal LVDS operation
DCS = 0, normal CMOS driver current strength
DISCNTL1 = 0, serial-data bit 27 is mapped to CNTL1
DISRES = 0, serial-data bit 27 is mapped to RES
ILVDS = 01, 3.5mA LVDS output current
0x14
14 ��
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
REGISTER
ADDRESS
(hex)
POWER-UP
DEFAULT
(hex)
0x1E
0x04
(read only)
ID = 00000100, device ID is 0x04
0x1F
0x0X
(read only)
RESERVED = 000
CAPS = 0, not HDCP capable
REVISION = XXXX
MAX9268
Table 1. Power-Up Default Register Map (see Table 12) (continued)
POWER-UP DEFAULT SETTINGS
(MSB FIRST)
X = Don’t care.
Table 2. Deserializer Device Address Defaults (Register 0x01)
ADD1
ADD0
D7
D6
D5
D4
D3
D2
D1
D0
SERIALIZER
DEVICE
ADDRESS*
(hex)
Low
Low
1
0
0
X**
0
0
0
R/W
80
90
Low
High
1
0
0
X**
0
1
0
R/W
84
94
Low
Open
1
0
0
X**
1
0
0
R/W
88
98
High
Low
1
1
0
X**
0
0
0
R/W
C0
D0
High
High
1
1
0
X**
0
1
0
R/W
C4
D4
High
Open
1
1
0
X**
1
0
0
R/W
C8
D8
Open
Low
0
1
0
X**
0
0
0
R/W
40
50
Open
High
0
1
0
X**
0
1
0
R/W
44
54
Open
Open
0
1
0
X**
1
0
0
R/W
48
58
DEVICE ADDRESS*
(bin)
PIN
DESERIALIZER
DEVICE
ADDRESS*
(hex)
*ADD0 and ADD1 affect the default device address values stored in the MAX9268 only. The default device address values stored
in the GMSL serializer may differ (see the 3-Level Inputs for Default Device Address section).
**X = 0 for the serializer address, X = 1 for the deserializer address.
______________________________________________________________________________________ 15
MAX9268
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
Typical Bitmapping and
Bus-Width Selection
The LVDS output has two selectable widths: 3-channel
and 4-channel. The MAX9268 outputs 3- or 4-channel
LVDS (Table 3). Serial data is mapped to outputs on the
MAX9268 according to Figures 12 and 13. In 3-channel mode, TXOUT3_ and CNTL1, CNTL2/MCLK are not
available. For both modes, the SD/CNTL0, SCK, and WS
pins are for I2S audio when audio is enabled. With audio
disabled, SD/CNTL0 becomes control signal CNTL0.
The MAX9268 outputs clock rates from 8.33MHz to
104MHz for 3-channel mode and 6.25MHz to 78MHz for
4-channel mode.
Serial Link Signaling and Data Format
The GMSL high-speed serial link uses CML signaling
with programmable preemphasis and AC-coupling. The
GMSL deserializer uses AC-coupling and programmable
channel equalization. When using both the preemphasis
and equalization, including internally generated over-
head bits, the GMSL link operates up to 3.125Gbps over
STP cable lengths of 15m or greater. The payload data
rate, which is the data rate available to the user or the
data rate after subtracting overhead, is 2.5Gbps.
The GMSL serializer scrambles and encodes the input
data and sends the 8b/10b coded signal through the
serial link. The MAX9268 deserializer recovers the
embedded serial clock and then samples, decodes, and
descrambles before outputting the data. Figures 14 and
15 show the serial-data packet format after unscrambling
and 8b/10b decoding. In 3-channel or 4-channel mode,
21 or 28 bits map to the TXOUT_ _ LVDS outputs. Serialdata bits 27 and 28 map to control outputs in 4-channel
mode. The audio channel bit (ACB) contains an encoded
audio signal derived from the three I2S signals (SD/
CNTL0, SCK, and WS). The forward control-channel
(FCC) bit carries the forward control data. The last bit
(PCB) is the parity bit of the previous 23 or 31 bits.
Table 3. Bus-Width Selection Using BWS
3-CHANNEL MODE
(BWS = LOW)
OUTPUT BITS
4-CHANNEL MODE
(BWS = HIGH)
TYPICAL BITMAPPING
AUXILIARY SIGNALS
MAPPING
TYPICAL BITMAPPING
AUXILIARY SIGNALS
MAPPING
DOUT[0:5]
R[0:5]
—
R[0:5]
—
DOUT[6:11]
G[0:5]
—
G[0:5]
—
DOUT[12:17]
B[0:5]
—
B[0:5]
—
DOUT[18:20]
HS, VS, DE
—
HS, VS, DE
—
DOUT[21:22]
Not used
Not used
R6, R7
—
DOUT[23:24]
Not used
Not used
G6, G7
—
DOUT[25:26]
Not used
Not used
B6, B7
—
DOUT27
Not used
Not used
RES*
CNTL1*
DOUT28
Not used
Not used
—
CNTL2/MCLK
—
SD/CNTL0
SD
—
SD/CNTL0
*See the Reserved Bit (RES)/CNTL1 section for details.
16 ��
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
TXCLKOUT+
CYCLE N-1
CYCLE N
TXOUT0+ /TXOUT0-
DOUT1
DOUT0
DOUT6
DOUT5
DOUT4
DOUT3
DOUT2
DOUT1
DOUT0
TXOUT1+/TXOUT1-
DOUT8
DOUT7
DOUT13 DOUT12 DOUT11 DOUT10
DOUT9
DOUT8
DOUT7
TXOUT2+/TXOUT2-
DOUT15 DOUT14 DOUT20 DOUT19 DOUT18 DOUT17 DOUT16 DOUT15 DOUT14
TXOUT3+/TXOUT3-
DOUT22 DOUT21 DOUT27 DOUT26 DOUT25 DOUT24 DOUT23 DOUT22 DOUT21
CNTL1
DOUT27
CNTL2/MCLK
DOUT28
SD/CNTL0
SD*
*ONLY WHEN I2S IS DISABLED.
Figure 12. LVDS Output Timing
TXCLKOUTTXCLKOUT+
CYCLE N-1
CYCLE N
TXOUT0+/TXOUT0-
R1
R0
G0
R5
R4
R3
R2
R1
R0
TXOUT1+/TXOUT1-
G2
G1
B1
B0
G5
G4
G3
G2
G1
TXOUT2+/TXOUT2-
B3
B2
DE
VS
HS
B5
B4
B3
B2
TXOUT3+/TXOUT3-
R7
R6
RES
B7
B6
G7
G6
R7
R6
Figure 13. Typical Panel Clock and Bit Assignment
______________________________________________________________________________________ 17
MAX9268
TXCLKOUT-
MAX9268
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
24 BITS
DOUT0 DOUT1
R0
DOUT17 DOUT18 DOUT19 DOUT20 ACB
R1
B5
HS
VS
FCC
PCB
DE
LVDS
DATA
(3 CHANNELS)
AUDIO
CHANNEL BIT
FORWARD
CONTROLCHANNEL BIT
PACKET
PARITY
CHECK BIT
NOTE: TYPICAL LOCATIONS OF THE RGB DATA AND CONTROL SIGNALS.
Figure 14. 3-Channel Mode Serial Link Data Format
32 BITS
DOUT0 DOUT1
R0
R1
DOUT17 DOUT18 DOUT19 DOUT20 DOUT21 DOUT22 DOUT23 DOUT24 DOUT25 DOUT26 DOUT27 DOUT28 ACB
B5
HS
VS
DE
R6
LVDS
DATA
(TXOUT[2:0]_)
R7
G6
G7
B6
B7
FCC
PCB
CNTL2
AUDIO
CHANNEL/CNTL0
BIT
LVDS
DATA
(TXOUT3_)
RES/CNTL1*
FORWARD
CONTROLCHANNEL BIT
NOTE: TYPICAL LOCATIONS OF THE LVDS RGB DATA AND CONTROL SIGNALS.
PACKET
PARITY
CHECK BIT
*DOUT27 OUTPUTS TO LVDS DATA (TXOUT3_) AND/OR EXTERNAL PIN (CNTL1).
Figure 15. 4-Channel Mode Serial Link Data Format
Reserved Bit (RES)/CNTL1
In 4-channel mode, the MAX9268 deserializes serialdata bit 27 to both RES and CNTL1 by default (both
DISCNTL and DISRES = 0). Setting DISRES (D2 of
register 0x14) = 1 forces RES low. Setting DISCNTL1 (D3
of register 0x14) = 1 forces CNTL1 low.
Reverse Control Channel
The GMSL serializer uses the reverse control
channel to receive I2C/UART and interrupt signals from
the MAX9268 in the opposite direction of the video
stream. The reverse control channel and forward video
data coexist on the same twisted pair forming a bidirectional link. The reverse control channel operates independently from the forward control channel. The reverse
control channel is available 500Fs after power-up. The
GMSL serializer temporarily disables the reverse control
channel for 350Fs after starting/stopping the forward
serial link.
Data-Rate Selection
The MAX9268 uses the DRS input to set the TXCLKOUT_
frequency. Set DRS high for a TXCLKOUT_ frequency
of 6.25MHz to 12.5MHz (4-channel mode), or 8.33MHz
to 16.66MHz (3-channel mode). Set DRS low for normal
operation with a TXCLKOUT_ frequency of 12.5MHz
to 78MHz (4-channel mode), or 16.66MHz to 104MHz
(3-channel mode).
Audio Channel
The I2S audio channel supports audio sampling rates
from 8kHz to 192kHz and audio word lengths from 4 bits
to 32 bits. The audio bit clock (SCK) does not have to
be synchronized with TXCLKOUT_. The GMSL serializer
automatically encodes audio data into a single bit stream
18 ��
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
output on CNTL2/MCLK at the expense of one less
control line in 4-channel mode (3-channel mode is not
affected). By default, CNTL2/MCLK operates as a control data output, and MCLK is turned off. Set MCLKDIV
(MAX9268 register 0x12, D[6:0]) to a nonzero value
to enable the MCLK output. Set MCLKDIV to 0x00 to
disable MCLK and set CNTL2/MCLK as a control data
output.
The output MCLK frequency is:
Low TXCLKOUT_ frequencies limit the maximum
audio sampling rate. Table 4 lists the maximum audio
sampling rate for various TXCLKOUT_ frequencies.
Spread-spectrum settings do not affect the I2S data rate
or WS clock frequency.
fMCLK =
where:
Additional MCLK Output for
Audio Applications
fSRC
MCLKDIV
fSRC = the MCLK source frequency (Table 5)
MCLKDIV = the divider ratio from 1 to 127
Choose MCLKDIV values such that fMCLK is not
greater than 60MHz. MCLK frequencies derived from
TXCLKOUT_ (MSCLKSRC = 0) are not affected by
spread-spectrum settings in the MAX9268. However,
enabling spread spectrum in the GMSL serializer introduces spread spectrum into MCLK. Spread-spectrum
settings of either device do not affect MCLK frequencies
derived from the internal oscillator. The internal oscillator frequency ranges from 100MHz to 150MHz over all
process corners and operating conditions.
Some audio DACs such as the MAX9850 do not require
a synchronous main clock (MCLK), while other DACs
require MCLK to be a specific multiple of WS. If the audio
DAC chip needs the MCLK to be a multiple of WS, use
an external PLL to regenerate the required MCLK from
WS or SCK.
For audio applications that have WS synchronous to
TXCLKOUT_, the MAX9268 provides a divided clock
Table 4. Maximum Audio WS Frequency (kHz) for Various TXCLKOUT_ Frequencies
TXCLKOUT_ FREQUENCY
(DRS = LOW)
(MHz)
WORD
LENGTH
(BITS)
TXCLKOUT_ FREQUENCY
(DRS = HIGH)
(MHz)
12.5
15
16.6
> 20
6.25
7.5
8.33
> 10
8
> 192
> 192
> 192
> 192
> 192
> 192
> 192
> 192
16
> 192
> 192
> 192
> 192
> 192
> 192
> 192
> 192
18
185.5
> 192
> 192
> 192
185.5
> 192
> 192
> 192
20
174.6
> 192
> 192
> 192
174.6
> 192
> 192
> 192
24
152.2
182.7
> 192
> 192
152.2
182.7
> 192
> 192
32
123.7
148.4
164.3
> 192
123.7
148.4
164.3
> 192
Table 5. fSRC Settings
MCLKSRC SETTING
(REGISTER 0x12, D7)
DATA-RATE SETTING
High speed
0
Low speed
1
—
BUS-WIDTH SETTING
MCLK SOURCE FREQUENCY (fSRC)
3-channel mode
4-channel mode
3 x fTXCLKOUT_
4 x fTXCLKOUT_
3-channel mode
6 x fTXCLKOUT_
4-channel mode
8 x fTXCLKOUT_
—
Internal oscillator
(120MHz, typ)
______________________________________________________________________________________ 19
MAX9268
synchronous with TXCLKOUT_. The MAX9268 deserializer decodes the audio stream and stores audio words
in a FIFO. Audio rate detection uses an internal oscillator
to continuously determine the audio data rate and output
the audio in I2S format. The audio channel is enabled by
default. When the audio channel is disabled, the audio
data input (SD) on the serializer becomes a control input
(CNTL0) and SD/CNTL0 becomes a control output on
the deserializer.
MAX9268
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
Control Channel and Register Programming
back towards the serializer. The speed of the control channel ranges from 100kbps to 1Mbps in both directions. The
GMSL serializer and MAX9268 deserializer automatically
detect the control-channel bit rate in base mode. Packet bit
rates can vary up to 3.5x from the previous bit rate (see the
Changing the Clock Frequency section). Figure 16 shows
the UART protocol for writing and reading in base mode
between the FC and the GMSL serializer/MAX9268.
The control channel runs in base mode or bypass mode
according to the mode-selection (MS) input of the device
connected to the FC. In base mode, the control-channel
transactions are half-duplex and in bypass mode they are
full-duplex.
Figure 17 shows the UART data format. Figures 18 and 19
detail the formats of the SYNC byte (0x79) and the ACK
byte (0xC3). The FC and the connected slave chip generate the SYNC byte and ACK byte, respectively. Events
such as device wake-up and interrupt generate transitions
on the control channel that should be ignored by the FC.
Data written to the GMSL serializer/MAX9268 registers do
not take effect until after the acknowledge byte is sent.
This allows the FC to verify write commands received without error, even if the result of the write command directly
affects the serial link. The slave uses the SYNC byte to
synchronize with the host UART data rate automatically. If
the INT or MS inputs of the MAX9268 toggle while there is
control-channel communication, the control-channel communication can be corrupted since INT has priority on the
control channel. In the event of a missed acknowledge, the
FC should assume there was an error in the packet when
the slave device receives it, or that an error occurred during
the response from the slave device. In base mode, the FC
must keep the UART Tx/Rx lines high for 16 bit times before
sending a new packet.
The control channel is available for the FC to send and
receive control data over the serial link simultaneously with
the high-speed data, to program registers on the link serializer/deserializer or to program peripherals. Configuring the
CDS pin allows a FC to control the link from the side of the
serializer or deserializer, or with dual FCs from both sides,
to support a wide variety of applications.
Base Mode
In base mode the FC is the host, and in order to access the
registers of the serializer or deserializer it must use the
GMSL UART format and protocol. The FC accesses
peripherals with an I2C interface by sending GMSL UART
packets, which are converted to I2C by the serializer
or deserializer on the remote side of the link. The FC
communicates with a UART peripheral in base mode
(through INTTYPE register settings) using the GMSL UART
protocol. The device addresses of the GMSL serializer and
MAX9268 in base mode are programmable. The default
MAX9268 device address is determined by ADD0 and
ADD1 upon power-up, or after returning from a powerdown state (Table 2).
When the peripheral interface uses I2C (default), the GMSL
serializer/MAX9268 convert packets to I2C that have device
addresses different from those of the GMSL serializer or
MAX9268. The converted I2C bit rate is the same as the
original UART bit rate.
The GMSL serializer embeds control signals going to the
MAX9268 in the high-speed forward link. The MAX9268
uses a proprietary differential line coding to send signals
As shown in Figure 20, the remote-side device converts
the packets going to or coming from the peripherals from
the UART format to the I2C format and vice versa. The
remote device removes the byte number count and adds or
receives the ACK between the data bytes of I2C. The I2C’s
data rate is the same as the UART data rate.
WRITE DATA FORMAT
SYNC
DEV ADDR + R/W
REG ADDR
NUMBER OF BYTES
BYTE 1
BYTE N
ACK
MASTER WRITES TO SLAVE
MASTER READS FROM SLAVE
READ DATA FRMAT
SYNC
DEV ADDR + R/W
REG ADDR
NUMBER OF BYTES
MASTER WRITES TO SLAVE
ACK
BYTE 1
BYTE N
MASTER READS FROM SLAVE
Figure 16. GMSL UART Protocol for Base Mode
20 ��
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
MAX9268
1 UART FRAME
START
D0
D1
D2
D3
D4
FRAME 1
D5
D6
D7
PARITY
STOP
FRAME 2
STOP
FRAME 3
START
STOP
START
Figure 17. GMSL UART Data Format for Base Mode
START
D0
D1
D2
D3
D4
D5
D6
D7
1
0
0
1
1
1
1
0
PARITY STOP
D0
D1
D2
D3
D4
D5
D6
D7
1
1
0
0
0
0
1
1
START
Figure 18. SYNC Byte (0x79)
PARITY STOP
Figure 19. ACK Byte (0xC3)
UART-TO-I2C CONVERSION OF WRITE PACKET (I2CMETHOD = 0)
FC
GMSL SERIALIZER/MAX9268
11
SYNC FRAME
11
DEVICE ID + WR
GMSL SERIALIZER/MAX9268
11
REGISTER ADDRESS
11
NUMBER OF BYTES
11
DATA 0
11
DATA N
11
ACK FRAME
PERIPHERAL
1
S
7
DEV ID
1 1
W A
8
REG ADDR
8
DATA 0
1
A
1
A
8
DATA N
1 1
A P
UART-TO-I2C CONVERSION OF READ PACKET (I2CMETHOD = 0)
FC
GMSL SERIALIZER/MAX9268
11
SYNC FRAME
11
DEVICE ID + RD
GMSL SERIALIZER/MAX9268
11
REGISTER ADDRESS
11
NUMBER OF BYTES
11
ACK FRAME
11
DATA 0
11
DATA N
PERIPHERAL
1
S
7
DEV ID
: MASTER TO SLAVE
1 1
W A
8
REG ADDR
1 1
A S
: SLAVE TO MASTER
7
DEV ID
S: START
1 1
R A
8
DATA 0
P: STOP
1
A
8
DATA N
1 1
A P
A: ACKNOWLEDGE
Figure 20. Format Conversion between GMSL UART and I2C with Register Address (I2CMETHOD = 0)
______________________________________________________________________________________ 21
MAX9268
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
Interfacing Command-Byte-Only I2C Devices
The GMSL serializer and MAX9268 UART-to-I2C
conversion interfaces with devices that do not require
register addresses, such as the MAX7324 GPIO expander. In this mode, the I2C master ignores the register
address byte and directly reads/writes the subsequent
data bytes (Figure 21). Change the communication
method of the I2C master using the I2CMETHOD bit.
I2CMETHOD = 1 sets command-byte-only mode, while
I2CMETHOD = 0 sets normal mode where the first byte
in the data stream is the register address.
(CDS = low). Bypass mode accepts bit rates down to
28kbps in the forward direction (serializer to deserializer), and 7.7kbps in the reverse direction (deserializer to
serializer). See the Interrupt Control section for interrupt
functionality limitations. The control-channel data pattern
should not be held low longer than 100µs if interrupt
control is used.
Interrupt Control
The INT pin of the GMSL serializer is the interrupt output
and the INT pin of the MAX9268 is the interrupt input.
The interrupt output on the GMSL serializer follows the
transitions at the interrupt input, even during reversechannel communication or loss of lock. This interrupt
function supports remote-side functions such as touchscreen peripherals, remote power-up, or remote monitoring. Interrupts that occur during periods where the
reverse control channel is disabled, such as link startup/
shutdown, are automatically resent once the reverse
control channel becomes available again. Bit D4 of
register 0x06 in the MAX9268 also stores the interrupt
input state. The INT output of the GMSL serializer is low
after power-up. In addition, the FC can set the INT output
of the serializer by writing to the SETINT register bit. In
normal operation, the state of the interrupt output
changes when the interrupt input on the MAX9268 toggles.
Do not send a logic-low value longer than 100Fs in
either base or bypass mode to ensure proper interrupt
functionality.
Bypass Mode
In bypass mode, the GMSL serializer/MAX9268 ignore
UART communications. The FC is thereby free to
communicate with the peripherals using its own UART
protocol without concern that communication traffic
inadvertently misprograms the GMSL serializer or
MAX9268. The FC cannot access the GMSL serializer/
MAX9268 registers in this mode. Peripherals accessed
through the forward control channel using the UART
interface need to handle at least one TXCLKOUT_ period
of jitter due to the asynchronous sampling of the UART
signal by TXCLKOUT_.
Set MS = high to put the control channel into bypass
mode. For applications with the FC connected to the
deserializer (CDS is high), there is a 1ms wait time
between setting MS high and the bypass control channel
being active. There is no delay time when switching to
bypass mode when the FC is connected to the serializer
UART-TO-I2C CONVERSION OF WRITE PACKET (I2CMETHOD = 1)
FC
11
SYNC FRAME
GMSL SERIALIZER/MAX9268
11
11
DEVICE ID + WR
REGISTER ADDRESS
GMSL SERIALIZER/MAX9268
FC
PERIPHERAL
1
7
S DEV ID
11
NUMBER OF BYTES
11
DATA N
1 1
W A
8
DATA 0
UART-TO-I2C CONVERSION OF READ PACKET (I2CMETHOD = 1)
GMSL SERIALIZER/MAX9268
11
11
11
SYNC FRAME
DEVICE ID + RD
REGISTER ADDRESS
GMSL SERIALIZER/MAX9268
11
DATA 0
11
NUMBER OF BYTES
11
ACK FRAME
11
ACK FRAME
1
A
8
DATA N
11
DATA 0
11
DATA N
PERIPHERAL
1
S
: MASTER TO SLAVE
: SLAVE TO MASTER
7
DEV ID
S: START
1 1
R A
8
DATA 0
P: STOP
1
A
8
DATA N
1 1
A P
1 1
A P
A: ACKNOWLEDGE
Figure 21. Format Conversion Between GMSL UART and I2C with Register Address (I2CMETHOD = 1)
22 ��
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
in the GMSL serializer spread settings only affect the
MAX9268 MCLK output if it is derived from TXCLKOUT_
(MCLKSRC = 0).
The MAX9268 includes a sawtooth divider to control the
spread-modulation rate. Autodetection or manual programming of the TXCLKOUT_ operation range guarantees a
spread-spectrum modulation frequency within 20kHz to
40kHz. Additionally, manual configuration of the sawtooth
divider (SDIV, 0x03 D[4:0]) allows the user to set a modulation frequency according to the TXCLKOUT_ frequency.
Always keep the modulation frequency between 20kHz to
40kHz to ensure proper operation.
Spread Spectrum
To reduce the EMI generated by the transitions on the serial
link and outputs of the MAX9268, both the GMSL serializer and MAX9268 support spread spectrum. Turning on
spread spectrum on the GMSL serializer spreads the serial
data and the MAX9268 outputs. Do not enable spread for
both the GMSL serializer and the MAX9268. The two selectable spread-spectrum rates at the MAX9268 outputs are
Q2% and Q4% (Table 7).
Set the MAX9268 SSEN input high to select 2% spread
at power-up, and SSEN input low to select no spread at
power-up. The state of SSEN is latched upon power-up or
when resuming from power-down mode.
Turning on spread spectrum on the GMSL serializer or the
MAX9268 does not affect the audio data stream. Changes
Table 6. Cable Equalizer Boost Levels
BOOST SETTING
(0x05 D[3:0])
0000
0001
0010
0011
TYPICAL BOOST GAIN (dB)
2.1
2.8
3.4
4.2
0100
5.2
Power-up default
(EQS = high)
0101
6.2
0110
7
0111
8.2
Manual Programming of the
Spread-Spectrum Divider
The modulation rate for the MAX9268 relates to the
TXCLKOUT_ frequency as follows:
f
fM = (1 + DRS) TXCLKOUT_
MOD × SDIV
where:
fM = Modulation frequency
DRS = DRS input value (0 or 1)
fTXCLKOUT_ = LVDS clock frequency
MOD = Modulation coefficient given in Table 8
SDIV = 5-bit SDIV setting, manually programmed by the FC
To program the SDIV setting, first look up the modulation
coefficient according to the spread-spectrum settings.
Table 7. LVDS and Control Output Spread
Rates
SS
SPREAD (%)
00
No spread spectrum.
Power-up default when SSEN = low.
01
Q2% spread spectrum.
Power-up default when SSEN = high.
10
No spread spectrum
11
Q4% spread spectrum
Table 8. Modulation Coefficients and
Maximum SDIV Settings
1000
9.4
1001
10.7
Power-up default
(EQS = low)
SPREADSPECTRUM
SETTING (%)
MODULATION
COEFFICIENT
(dec)
SDIV UPPER
LIMIT (dec)
1010
11.7
4
208
15
1011
13
2
208
30
______________________________________________________________________________________ 23
MAX9268
Line Equalizer
The MAX9268 includes an adjustable line equalizer to
further compensate cable attenuation at high frequencies.
The cable equalizer has 12 selectable levels of compensation, from 2.1dB to 13dB (Table 6). The EQS input selects
the default equalization level at power-up. The state of EQS
is latched upon power-up or when resuming from powerdown mode. To select other equalization levels, set the
corresponding register bits in the MAX9268 (0x05 D[3:0]).
Use equalization in the MAX9268, together with preemphasis in the GMSL serializer, to create the most reliable link
for a given cable.
MAX9268
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
Solve the above equation for SDIV using the desired pixel
clock and modulation frequencies. If the calculated SDIV
value is larger than the maximum allowed SDIV value in
Table 8, set SDIV to the maximum value.
Sleep Mode
The GMSL serializer/MAX9268 include low-power sleep
mode to reduce power consumption on the device not
attached to the FC (the MAX9268 in LCD applications and
the GMSL serializer in camera applications). Set the corresponding remote IC’s SLEEP bit to 1 to initiate sleep mode.
The GMSL serializer sleeps immediately after setting its
SLEEP = 1. The MAX9268 sleeps after serial link inactivity
or 8ms (whichever arrives first) after setting its SLEEP = 1.
See the Link Startup Procedure section for details on waking up the device for different FC and starting conditions.
The FC side device cannot enter into sleep mode. If an
attempt is made to program the FC side device for sleep,
the SLEEP bit remains 0. Use the power-down mode to
bring the FC side device into a low-power state.
Power-Down Mode
The MAX9268 includes a power-down mode to further
reduce power consumption. Set PWDN low to enter powerdown mode. While in power-down mode, the outputs of
the device remain high impedance. Entering power-down
mode resets the internal registers of the device. In addition,
upon exiting power-down mode, the MAX9268 relatches
the state of SSEN, EQS, DRS, and ADD_.
Configuration Link Mode
The GMSL includes a low-speed configuration link to allow
control-data connection between the two devices in the
absence of a valid clock input. In either display or camera
applications, the configuration link can be used to program
equalizer/preemphasis or other registers before establishing the video link. An internal oscillator provides a clock
for establishing the serial configuration link between the
GMSL serializer and the MAX9268. Set CLINKEN = 1 on
the GMSL serializer to turn on the configuration link. The
configuration link remains active as long as the video link
has not been enabled. The video link overrides the configuration link and attempts to lock when SEREN = 1.
Link Startup Procedure
Table 9 lists four startup cases for video-display applications. Table 10 lists two startup cases for image-sensing
applications. In either video-display or image-sensing
applications, the control link is always available after the
high-speed data link or the configuration link is established
and the GMSL serializer/MAX9268 registers or peripherals
are ready for programming.
Video-Display Applications
For a video-display application with a remote display unit,
connect the FC to the GMSL serializer and set CDS = low
for both the GMSL serializer and the MAX9268. Table 9
summarizes the four startup cases based on the settings
of AUTOS and MS.
Case 1: Autostart Mode
After power-up or when PWDN transitions from low to
high for both the serializer and deserializer, the serial link
establishes whether a stable clock is present. The GMSL
serializer locks to the clock and sends the serial data to the
MAX9268. The MAX9268 then detects activity on the serial
link and locks to the input serial data.
Case 2: Standby Start Mode
After power-up or when PWDN transitions from low to high
for both the serializer and deserializer, the MAX9268 starts
up in sleep mode, and the GMSL serializer stays in standby
mode (does not send serial data). Use the FC and program
the serializer to set SEREN = 1 to establish a video link
or CLINKEN = 1 to establish the configuration link. After
locking to a stable clock (for SEREN = 1) or the internal
oscillator (for CLINKEN = 1), the serializer sends a wakeup signal to the MAX9268. The MAX9268 exits sleep mode
after locking to the serial data and sets SLEEP = 0. If after
8ms the MAX9268 does not lock to the input serial data, the
deserializer goes back to sleep and the internal sleep bit
remains set (SLEEP = 1).
Case 3: Remote Side Autostart Mode
After power-up or when PWDN transitions from low to
high, the remote device (MAX9268) starts up and tries to
lock to an incoming serial signal with sufficient power. The
host side (GMSL serializer) is in standby mode and does
not try to establish a link. Use the FC and program the
serializer to set SEREN = 1 (and apply a stable clock signal)
to establish a video link, or CLINKEN = 1 to establish the
configuration link. In this case, the MAX9268 ignores the
short wake-up signal sent from the GMSL serializer.
Case 4: Remote Side in Sleep Mode
After power-up or when PWDN transitions from low to high,
the remote device (MAX9268) starts up in sleep mode.
The high-speed link establishes automatically after the
GMSL serializer powers up with a stable clock signal and
sends a wake-up signal to the MAX9268. Use this mode in
applications where the MAX9268 powers up before the
GMSL serializer.
24 ��
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
CASE
AUTOS
(GMSL
SERIALIZER)
GMSL SERIALIZER
POWER-UP STATE
MS
(MAX9268)
MAX9268
POWER-UP STATE
LINK STARTUP MODE
1
Low
Serialization
enabled
Low
Normal
(SLEEP = 0)
Both devices power up with serial link
active (autostart).
High
Sleep mode
(SLEEP = 1)
Serial link is disabled and the
MAX9268 powers up in sleep mode.
Set SEREN = 1 or CLINKEN = 1 in the
GMSL serializer to start the serial link
and wake up the MAX9268.
Low
Normal
(SLEEP = 0)
Both devices power up in normal
mode with the serial link disabled. Set
SEREN = 1 or CLINKEN = 1 in the
GMSL serializer to start the serial link.
2
3
4
High
Serialization
disabled
High
Serialization
disabled
Low
Serialization
enabled
MAX9268 starts in sleep mode. Link
autostarts upon GMSL serializer
power-up. Use this case when the
MAX9268 powers up before the
serializer.
In sleep mode
(SLEEP = 1)
High
SLEEP = 1, VIDEO LINK OR CONFIG
LINK NOT LOCKED AFTER 8ms
MS PIN
SETTING
SLEEP BIT
POWER-UP VALUE
LOW
HIGH
0
1
SLEEP
WAKE-UP
SIGNAL
SERIAL LINK ACTIVITY STOPS OR 8ms ELAPSES AFTER
FC SETS SLEEP = 1
SEND INT TO
GMSL SERIALIZER
INT CHANGES FROM
LOW TO HIGH OR
HIGH TO LOW
POWER-ON
IDLE
SIGNAL
DETECTED
PWDN = HIGH,
POWER-ON
SERIAL PORT
LOCKING
CONFIG LINK
UNLOCKED
CONFIG LINK
OPERATING
PROGRAM
REGISTERS
CONFIG LINK
LOCKED
VIDEO LINK
LOCKED
VIDEO LINK
UNLOCKED
0
SLEEP
PRBSEN = 0
ALL STATES
PWDN = LOW OR
POWER-OFF
POWER-DOWN
OR
POWER-OFF
VIDEO LINK
OPERATING
0
PRBSEN = 1
VIDEO LINK
PRBS TEST
SLEEP
Figure 22. State Diagram, CDS = Low (LCD Application)
______________________________________________________________________________________ 25
MAX9268
Table 9. Startup Selection for Display Applications (CDS = Low)
MAX9268
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
Image-Sensing Applications
frame over the reverse control channel and powers up.
Reset the sleep bit (SLEEP = 0) of the GMSL serializer
using a regular control-channel write packet to power up
the device fully. Send the sleep bit write packet at least
500Fs after the wake-up frame. The GMSL serializer goes
back to sleep mode if its sleep bit is not cleared within
5ms (min) after detecting a wake-up frame.
Case 1: Autostart Mode
After power-up or when PWDN transitions from low to
high, the GMSL serializer locks to a stable input clock
and sends the high-speed data to the MAX9268. The
deserializer locks to the serial data and outputs the video
data and clock.
Case 2: Sleep Mode
After power-up or when PWDN transitions from low to
high, the GMSL serializer starts up in sleep mode. Use the
FC to wake up the serializer by sending a GMSL protocol
UART frame containing at least three rising edges (e.g.,
0x66), at a bit rate no greater than 1Mbps. The low-power
wake-up receiver of the serializer detects the wake-up
Applications Information
For image-sensing applications, connect the FC to the
MAX9268 and set CDS = high for both the GMSL serializer and the MAX9268. The deserializer powers up normally (SLEEP = 0) and continuously tries to lock to a valid
serial input. Table 10 summarizes both startup cases,
based on the state of the GMSL serializer AUTOS pin.
Error Checking
The MAX9268 checks the serial link for errors and stores
the number of detected decoding errors in the 8-bit
register DECERR (0x0D). If a large number of decoding
errors are detected within a short duration, the deserializer
loses lock and stops the error counter. The deserializer
then attempts to relock to the serial data. DECERR resets
upon successful video link lock, successful readout of
DECERR (through UART), or whenever autoerror reset is
enabled. The MAX9268 does not check for decoding errors
during the internal PRBS test and DECERR is reset to 0x00.
Table 10. Startup Selection for Image-Sensing Applications (CDS = High)
CASE
AUTOS
(GMSL SERIALIZER)
GMSL SERIALIZER
POWER-UP STATE
MAX9268 POWER-UP
STATE
1
Low
Serialization enabled
Normal
(SLEEP = 0)
Autostart
High
Sleep mode
(SLEEP = 1)
Normal
(SLEEP = 0)
GMSL serializer is in sleep mode.
Wake up the serializer through the
control channel (FC attached to
MAX9268).
2
POWER-ON
IDLE
(REVERSE
CHANNEL
ACTIVE)
NO SIGNAL
DETECTED
ALL STATES
SIGNAL
DETECTED
PWDN = HIGH,
POWER-ON
PWDN = LOW OR
POWER-OFF
SERIAL PORT
LOCKING
VIDEO LINK
LOCKED
POWER-DOWN
OR
POWER-OFF
LINK STARTUP MODE
CONFIG LINK
UNLOCKED
CONFIG
LINK OPERATING
CONFIG LINK
LOCKED
PROGRAM
REGISTERS
VIDEO LINK
UNLOCKED
PRBSEN = 0
VIDEO LINK
OPERATING
PRBSEN = 1
VIDEO LINK
PRBS TEST
Figure 23. MAX9268 State Diagram, CDS = High (Camera Application)
26 ��
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
not required, the FCs can disable the forward and reverse
control channel through the REVCCEN and FWDCCEN
bits (0x04 D[1:0]) in the GMSL serializer/MAX9268. UART
communication across the serial link is prevented and
therefore contention between FCs can no longer occur.
During dual FC operation, if one of the CDS pins on either
side changes state, the link resumes the corresponding
state described in the Link Startup Procedure section.
Autoerror Reset
The default method to reset errors is to read the
respective error registers in the MAX9268 (0x0D, 0x0E).
Autoerror reset clears the decoding error counter DECERR
and the ERR output ~1Fs after ERR goes low. Autoerror
reset is disabled on power-up. Enable autoerror reset
through AUTORST (0x06 D6). Autoerror reset does not
run when the device is in PRBS test mode.
As an example of dual FC use in an image-sensing application, the GMSL serializer can be in sleep mode and
waiting for wake-up by the MAX9268. After wake-up, the
serializer-side FC sets the GMSL serializer’s CDS pin low
and assumes master control of the serializer’s registers.
Self-PRBS Test
The GMSL serializer/MAX9268 link includes a PRBS pattern
generator and bit-error verification function. Set PRBSEN
= 1 (0x04 D5) first in the GMSL serializer and then the
MAX9268 to start the PRBS test. Set PRBSEN = 0 (0x04 D5)
first in the MAX9268 and then the GMSL serializer to exit the
PRBS self-test. The MAX9268 uses an 8-bit register (0x0E)
to count the number of detected errors. The control link
also controls the start and stop of the error counting. During
PRBS mode, the device does not count decoding errors
and the MAX9268 ERR output reflects PRBS errors only.
Microcontrollers on Both Sides of the
GMSL Link (Dual µC Control)
Changing the Clock Frequency
Both the video clock rate (fTXCLKOUT_) and the controlchannel clock rate (fUART) can be changed on-the-fly
to support applications with multiple clock speeds. It is
recommended to enable the serial link after the video clock
stabilizes. Stop the video clock for 5Fs and restart the serial
link, or toggle SEREN after each change in the video clock
frequency, to recalibrate any automatic settings if a smooth
frequency change cannot be guaranteed. The reverse
control channel remains unavailable for 350Fs after serial
link start or stop. Limit on-the-fly changes in fUART to factors
of less than 3.5 at a time to ensure that the device recognizes the UART sync pattern. For example, when lowering
the UART frequency from 1Mbps to 100kbps, first send
data at 333kbps and then at 100kbps to have reduction
ratios of 3 and 3.333, respectively.
LOCK Output Loopback
Usually a single FC is used for GMSL device programming
and control-channel communications and is located either
on the serializer side for video-display applications or on
the deserializer (MAX9268) side for image-sensing applications. In the former case, the CDS pins of the serializer/
deserializer are set to low; in the latter case, they are set to
high. However, if the CDS pin of the serializer is low and the
same pin on the deserializer is high, then FCs connected
at each device are enabled as masters simultaneously. In
such a case, the FC on either side communicates with the
GMSL serializer and the MAX9268.
For quick loss-of-lock notification, the MAX9268 can loop
back its LOCK output to the GMSL serializer using the
INT signal. Connect the LOCK output to the INT input of
the MAX9268. The interrupt output on the GMSL serializer
follows the transitions at the LOCK output. Reverse controlchannel communication does not require an active forward
link to operate and accurately tracks the LOCK status of the
video link. LOCK asserts for video link only and not for the
configuration link.
Contention can occur if the FCs attempt to use the control
channel at the same time. The serializer/deserializer do
not in themselves provide a way to avoid contention. The
fact that an acknowledge is not received when contention
occurs can be used to trigger a retry. Alternatively, a higher
layer protocol can be implemented to avoid contention. In
addition, if UART communication across the serial link is
The MAX9268 has two open-drain GPIOs available.
GPIO1OUT and GPIO0OUT (0x06 D3, D1) set the output
state of the GPIOs. The GPIO input buffers are always
enabled. The input states are stored in GPIO1 and GPIO0
(0x06 D2, D0). SET GPIO1OUT/GPIO0OUT to 1 when
using GPIO1/GPIO0 as an input.
GPIOs
______________________________________________________________________________________ 27
MAX9268
ERR Output
The MAX9268 has an open-drain ERR output. This
output asserts low whenever the number of decoding errors
exceeds the error threshold ERRTHR (0x0C) during normal
operation, or when at least one PRBS error is detected during the PRBS test. ERR reasserts high whenever DECERR
(0x0D) resets due to DECERR readout, video link lock, or
autoerror reset.
MAX9268
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
Programming the Device Addresses
Both the GMSL serializer and the MAX9268 have programmable device addresses. This allows multiple GMSL devices along with I2C peripherals to coexist on the same control
channel. The serializer device address is stored in registers
0x00 of each device, while the deserializer device address
is stored in register 0x01 of each device. To change the
device address, first write to the device whose address
changes (register 0x00 of the GMSL serializer for serializer
device address change, or register 0x01 of the MAX9268
for deserializer device address change). Then write the
same address into the corresponding register on the other
device (register 0x00 of the MAX9268 for serializer device
address change, or register 0x01 of the GMSL serializer for
deserializer device address change).
3-Level Inputs for Default Device Address
ADD0 and ADD1 are 3-level inputs, which set the device
addresses stored in the MAX9268 (Table 2). Set the
desired device addresses by connecting ADD0/ADD1
through a pullup resistor to IOVDD, a pulldown resistor to
GND, or to high impedance. For digital control, use threestate logic to drive the 3-level logic inputs.
ADD0/ADD1 set the device addresses in the MAX9268
only and not the GMSL serializer. Set the GMSL serializer’s ADD0/ADD1 inputs to the same settings as the
MAX9268; alternatively, write to registers 0x00 and 0x01
of the GMSL serializer to reflect any changes made due
to the 3-level inputs.
Choosing I2C/UART Pullup Resistors
I2C/UART
Both
open-drain lines require pullup resistors to
provide a logic-high level. There are trade-offs between
power dissipation and speed, and a compromise made in
choosing pullup resistor values. Every device connected
to the bus introduces some capacitance even when the
device is not in operation. I2C specifies 300ns rise times to
go from low to high (30% to 70%) for fast mode, which is
defined for data rates up to 400kbps (see the I2C specifications in the AC Electrical Characteristics section for details).
To meet the fast-mode rise-time requirement, choose the
pullup resistors such that rise time tR = 0.85 x RPULLUP x
CBUS < 300ns. The waveforms are not recognized if the
transition time becomes too slow. The MAX9268 supports
I2C/UART rates up to 1Mbps.
AC-Coupling
AC-coupling isolates the receiver from DC voltages up
to the voltage rating of the capacitor. Four capacitors
(two at the serializer output and two at the deserializer
input) are needed for proper link operation and to provide
protection if either end of the cable is shorted to a high voltage. AC-coupling blocks low-frequency ground shifts and
low-frequency common-mode noise.
Selection of AC-Coupling Capacitors
Voltage droop and the digital sum variation (DSV) of
transmitted symbols cause signal transitions to start from
different voltage levels. Because the transition time is finite,
starting the signal transition from different voltage levels
causes timing jitter. The time constant for an AC-coupled
link needs to be chosen to reduce droop and jitter to an
acceptable level. The RC network for an AC-coupled link
consists of the CML receiver termination resistor (RTR),
the CML driver termination resistor (RTD), and the series
AC-coupling capacitors (C). The RC time constant for four
equal-value series capacitors is (C x (RTD + RTR))/4. RTD
and RTR are required to match the transmission line impedance (usually 100I). This leaves the capacitor selection
to change the system time constant. Use at least 0.2FF
high-frequency surface-mount ceramic capacitors, with
sufficient voltage rating to withstand a short to battery, to
pass the lower speed reverse control-channel signal. Use
capacitors with a case size less than 3.2mm x 1.6mm to
have lower parasitic effects to the high-speed signal.
Power-Supply Circuits and Bypassing
The MAX9268 uses a 3.0V to 3.6V VAVDD and VDVDD. All
single-ended inputs and outputs on the MAX9268 derive
power from a 1.7V to 3.6V VIOVDD, which scales with
IOVDD. Proper voltage-supply bypassing is essential for
high-frequency circuit stability.
Cables and Connectors
Interconnect for CML typically has a differential impedance
of 100I. Use cables and connectors that have matched
differential impedance to minimize any impedance discontinuities. Twisted-pair and shielded twisted-pair cables
tend to generate less EMI due to magnetic-field canceling
effects. Balanced cables pick up noise as common mode
rejected by the CML receiver. Table 11 lists the suggested
cables and connectors used in the GMSL link.
28 ��
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
Route the PCB traces for a CML/LVDS channel (there
are two conductors per CML/LVDS channel) in parallel to
maintain the differential characteristic impedance. Avoid
vias. Keep PCB traces that make up a differential pair equal
length to avoid skew within the differential pair.
ESD Protection
The MAX9268 ESD tolerance is rated for Human Body
Model, IEC 61000-4-2, and ISO 10605. The ISO 10605
and IEC 61000-4-2 standards specify ESD tolerance for
electronic systems. CML/LVDS I/O are tested for ISO 10605
ESD protection and IEC 61000-4-2 ESD protection. All
pins are tested for the Human Body Model. The Human
Body Model discharge components are CS = 100pF and
RD = 1.5kI (Figure 24). The IEC 61000-4-2 discharge
components are CS = 150pF and RD = 330I (Figure 25).
The ISO 10605 discharge components are CS = 330pF and
RD = 2kI (Figure 26).
Table 11. Suggested Connectors and
Cables for GMSL
VENDOR
CONNECTOR
CABLE
JAE Electronics, Inc.
MX38-FF
A-BW-Lxxxxx
Nissei Electric Co., Ltd.
GT11L-2S
F-2WME
AWG28
Rosenberger
D4S10A-40ML5-Z
Hochfrequenztechnik GmbH
1MI
HIGHVOLTAGE
DC
SOURCE
CHARGE-CURRENTLIMIT RESISTOR
CS
100pF
RD
330I
HIGHVOLTAGE
DC
SOURCE
CHARGE-CURRENTLIMIT RESISTOR
CS
150pF
DEVICE
UNDER
TEST
Figure 25. IEC 61000-4-2 Contact Discharge ESD Test Circuit
RD
2kI
DISCHARGE
RESISTANCE
Figure 24. Human Body Model ESD Test Circuit
STORAGE
CAPACITOR
Dacar 538
RD
1.5kI
STORAGE
CAPACITOR
DISCHARGE
RESISTANCE
DEVICE
UNDER
TEST
HIGHVOLTAGE
DC
SOURCE
CHARGE-CURRENTLIMIT RESISTOR
CS
330pF
DISCHARGE
RESISTANCE
STORAGE
CAPACITOR
DEVICE
UNDER
TEST
Figure 26. ISO 10605 Contact Discharge ESD Test Circuit
______________________________________________________________________________________ 29
MAX9268
Board Layout
Separate the digital signals and CML/LVDS high-speed
signals to prevent crosstalk. Use a four-layer PCB with
separate layers for power, ground, CML/LVDS, and digital
signals. Layout PCB traces close to each other for a 100I
differential characteristic impedance. The trace dimensions
depend on the type of trace used (microstrip or stripline).
Note that two 50I PCB traces do not have 100I differential impedance when brought close together because the
impedance goes down when the traces are brought closer.
MAX9268
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
Table 12. Register Table (see Table 1)
REGISTER
ADDRESS
0x00
0x01
BITS
NAME
VALUE
D[7:1]
SERID
XXXXXXX
D0
—
0
D[7:1]
DESID
XXXXXXX
D0
—
0
Reserved
00
No spread spectrum. Power-up default when
SSEN = low.
01
Q2% spread spectrum. Power-up default when
SSEN = high.
10
No spread spectrum
11
Q4% spread spectrum
0
Reserved
0
Disable I2S channel
1
Enable I2S channel
00
12.5MHz to 25MHz pixel clock
01
25MHz to 50MHz pixel clock
10
50MHz to 104MHz pixel clock
11
Automatically detect the pixel clock range
00
0.5Gbps to 1Gbps serial-data rate
01
1Gbps to 2Gbps serial-data rate
10
2Gbps to 3.125Gbps serial-data rate
11
Automatically detect serial-data rate
00
Calibrate spread-modulation rate only once after locking
01
Calibrate spread-modulation rate every 2ms after locking
10
Calibrate spread-modulation rate every 16ms after
locking
11
Calibrate spread-modulation rate every 256ms after
locking
0
Reserved
D[7:6]
D5
0x02
D4
D[3:2]
D[1:0]
D[7:6]
SS
—
AUDIOEN
PRNG
SRNG
AUTOFM
0x03
D5
—
D[4:0]
SDIV
FUNCTION
Serializer device address. Power-up default address
determined by ADD0 and ADD1 (see Table 2).
Reserved
Deserializer device address. Power-up default address
determined by ADD0 and ADD1 (see Table 2).
00000
Autocalibrate sawtooth divider
XXXXX
Manual SDIV setting. See the Manual Programming of
Spread-Spectrum Divider section.
30 ��
DEFAULT
VALUE
XX00XX0
0
XX01XX0
0
00, 01
0
1
11
11
00
0
00000
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
REGISTER
ADDRESS
BITS
NAME
D7
LOCKED
D6
OUTENB
D5
PRBSEN
D4
INTTYPE
LOCK output is low
1
LOCK output is high
0
Enable outputs
1
Disable outputs
0
Disable PRBS test
1
Enable PRBS test
0
Normal mode. Default value depends on CDS and MS
pin values at power-up).
1
Activate sleep mode. Default value depends on CDS
and MS pin values at power-up).
00
Base mode uses I2C peripheral interface
01
Base mode uses UART peripheral interface
10, 11
D1
REVCCEN
D0
FWDCCEN
D7
D[6:5]
D4
I2CMETHOD
HPFTUNE
PDHF
0x05
D[3:0]
EQTUNE
FUNCTION
0
SLEEP
0x04
D[3:2]
VALUE
DEFAULT
VALUE
0
(read only)
0
0
0, 1
00
Base mode peripheral interface disabled
0
Disable reverse control channel to serializer (sending)
1
Enable reverse control channel to serializer (sending)
0
Disable forward control channel from serializer
(receiving)
1
Enable forward control channel from serializer (receiving)
0
I2C conversion sends the register address
1
Disable sending of I2C register address (commandbyte-only mode)
00
7.5MHz equalizer highpass cutoff frequency
01
3.75MHz cutoff frequency
10
2.5MHz cutoff frequency
11
1.87MHz cutoff frequency
0
High-frequency boosting enabled
1
High-frequency boosting disabled
0000
2.1dB equalizer boost gain
0001
2.8dB equalizer boost gain
0010
3.4dB equalizer boost gain
0011
4.2dB equalizer boost gain
0100
5.2dB equalizer boost gain. Power-up default when
EQS = high.
0101
6.2dB equalizer boost gain
0110
7dB equalizer boost gain
0111
8.2dB equalizer boost gain
1000
9.4dB equalizer boost gain
1001
10.7dB equalizer boost gain. Power-up default when
EQS = low.
1010
11.7dB equalizer boost gain
1011
13dB equalizer boost gain
11XX
Do not use
1
1
0
01
0
0100, 1001
______________________________________________________________________________________ 31
MAX9268
Table 12. Register Table (see Table 1) (continued)
MAX9268
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
Table 12. Register Table (see Table 1) (continued)
REGISTER
ADDRESS
NAME
VALUE
D7
—
0
Reserved
D6
AUTORST
0
Do not automatically reset error registers and outputs
1
Automatically reset error registers and outputs
D5
DISINT
0
Enable interrupt transmission to serializer
1
Disable Interrupt transmission to serializer
D4
INT
0
INT input = low (read only)
1
INT input = high (read only)
D3
GPIO1OUT
0
Output low to GPIO1
1
Output high to GPIO1
D2
GPIO1
0
GPIO1 is low
1
GPIO1 is high
D1
GPIO0OUT
0
Output low to GPIO0
1
Output high to GPIO0
D0
GPIO0
0
GPIO0 is low
1
GPIO0 is high
1
(read only)
0x07
D[7:0]
—
01010100
Reserved
01010100
0x08
D[7:0]
—
00110000
Reserved
00110000
0x09
D[7:0]
—
11001000
Reserved
11001000
0x0A
D[7:0]
—
00010010
Reserved
00010010
0x0B
D[7:0]
—
00100000
Reserved
00100000
0x0C
D[7:0]
ERRTHR
XXXXXXXX
Error threshold for decoding errors. ERR = low when
DECERR > ERRTHR.
00000000
0x0D
D[7:0]
DECERR
XXXXXXXX
Decoding error counter. This counter remains zero while
the device is in PRBS test mode.
00000000
(read only)
0x0E
D[7:0]
PRBSERR
XXXXXXXX
PRBS error counter
00000000
(read only)
D7
MCLKSRC
D[6:0]
MCLKDIV
D[7:5]
—
XXX
Reserved
(read only)
D[4:0]
—
10000
Reserved
10000
0x06
0x12
0x13
FUNCTION
DEFAULT
VALUE
BITS
0
MCLK derived from PCLK (see Table 5)
1
MCLK derived from internal oscillator
0000000
MCLK disabled
XXXXXXX
MCLK divider
32 ��
0
0
0
0
(read only)
1
1
(read only)
1
0
0000000
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
REGISTER
ADDRESS
NAME
VALUE
D[7:6]
—
00
Reserved
D5
FORCELVDS
0
Normal operation
1
Force LVDS outputs low
0
Normal driver current for CMOS outputs (WS, SCK, SD/
CNTL0, CNTL1, CNTL2/MCLK)
1
Strong driver current for CMOS outputs (WS, SCK, SD/
CNTL0, CNTL1, CNTL2/MCLK)
0
Serial-data bit 27 is mapped to CNTL1
1
CNTL1 forced low
0
Serial-data bit 27 is mapped to RES
1
RES bit forced low
00
1.75mA LVDS current
01
3.5mA LVDS current
10
Do not use
11
7mA LVDS current
Device identifier
(MAX9268 = 0x04)
00000100
(read only)
Reserved
000
(read only)
D4
0x14
D3
DISCNTL1
D2
DISRES
D[1:0]
0x1E
0x1F
DCS
ILVDS
D[7:0]
ID
00000100
D[7:5]
—
000
D4
CAPS
D[3:0]
REVISION
FUNCTION
DEFAULT
VALUE
BITS
00
0
0
0
0
01
0
Not HDCP capable
1
HDCP capable
0
(read only)
XXXX
Device revision
(read only)
X = Don’t care.
______________________________________________________________________________________ 33
MAX9268
Table 12. Register Table (see Table 1) (continued)
MAX9268
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
Typical Application Circuit
TXCLK+/-
RXCLKIN+/-
TX0+/TO TX2+/-
RXIN0+/TO RXIN2+/-
GPU
TCLKOUT+/-
RXCLK+/RX0+/TO RX2+/-
TXOUT0+/TO TXOUT2+/-
CDS
45kI
45kI
5kI
5kI
CDS
AUTOS
LMN1
LMN0
ECU
MAX9268
DISPLAY
MAX9249
UART
Tx
Rx
LFLT
INT
MS
RX/SDA
TX/SCL
OUT+
IN+
OUT-
IN50kI
LFLT
INT
MS
TO PERIPHERALS
INT
RX/SDA
TX/SCL
50kI
SCL
SDA
WS
LOCK
WS
SCK
AUDIO
WS
SCK
SD
SCK
SD
DISPLAY APPLICATION
PLL
Chip Information
MCLK
OUT
IN
NOTE: NOT ALL PULLUP/PULLDOWN RESISTORS ARE SHOWN. SEE PIN DESCRIPTION FOR DETAILS.
PROCESS: CMOS
MAX9850
SD/CNTL0
WS
SCK
SD/CNTL0
Package Information
For the latest package outline information and land patterns
(footprints), go to www.maxim-ic.com/packages. Note that a
“+”, “#”, or “-” in the package code indicates RoHS status only.
Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE
48 TQFP-EP
C48E+8
OUTLINE LAND PATTERN
NO.
NO.
21-0065
34 ��
90-0138
Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
REVISION
NUMBER
REVISION
DATE
0
4/10
Initial release
—
1
5/10
Changed conditions for LVDS output enable/disable times and SCK jitter limits in
the AC Electrical Characteristics table
5
2
1/11
Added Patent Pending to Features
1
DESCRIPTION
PAGES
CHANGED
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied.
Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2011
Maxim Integrated Products 35
Maxim is a registered trademark of Maxim Integrated Products, Inc.
MAX9268
Revision History

Open as PDF

Similar pages: NSC DS92LV0421; TI DS90UH926Q; TI DS92LX1621; TI DS90UH925QSQX; TI DS90UB903Q; AD AD9522; TI TLK6002ZEU; NSC LMX9820ASMX; MAXIM MAX9259GCB/V+; MAXIM MAX9270; MAXIM MAX9249; PHILIPS LC171W03-A4; MAXIM MAX16915AUB/V+; MAXIM MAX9271GTJ/V+; MAXIM MAX9272; MAXIM MAX9273; MAXIM MAX15046_10; MAXIM MAX15501GTJ+; MAXIM MAX15501GTJ+; MAXIM MAX3806GTC+; MAXIM MAX9257AGTV; MAXIM MAX9257GCM/V+