FUJITSU SEMICONDUCTOR DATA SHEET DS05–13109–3E Memory FRAM 64 K (8 K × 8) Bit I2C MB85RC64 ■ DESCRIPTION The MB85RC64 is a FRAM (Ferroelectric Random Access Memory) Stand-Alone chip in a configuration of 8,192 words × 8 bits, using the ferroelectric process and silicon gate CMOS process technologies for forming the nonvolatile memory cells. The MB85RC64 adopts the two-wire serial interface. Unlike SRAM, the MB85RC64 is able to retain data without using a data backup battery. The read/write endurance of the nonvolatile memory cells used for the MB85RC64 has improved to be at least 1010 cycles, significantly out performing Flash memory and E2PROM in the number. The MB85RC64 does not need a polling sequence after writing to the memory such as the case of Flash memory nor E2PROM. ■ FEATURES • • • • • • • • • Bit configuration : 8,192 words × 8 bits Operating power supply voltage : 2.7 V to 3.6 V Operating frequency : 400 kHz (Max) Two-wire serial interface : I2C-bus specification ver. 2.1 compliant, supports Standard-mode/ Fast-mode. Fully controllable by two ports: serial clock (SCL) and serial data (SDA). Operating temperature range : − 40 °C to +85 °C Data retention : 10 years ( + 75 °C) Read/write endurance : 1010 times Package : Plastic / SOP, 8-pin (FPT-8P-M02) Low power consumption : Operating current 0.15 mA (Max: @400 kHz), Standby current 5 μA (Typ) Copyright©2010-2011 FUJITSU SEMICONDUCTOR LIMITED All rights reserved 2011.6 MB85RC64 ■ PIN ASSIGNMENT (TOP VIEW) A0 1 8 VDD A1 2 7 WP A2 3 6 SCL VSS 4 5 SDA (FPT-8P-M02) ■ PIN FUNCTIONAL DESCRIPTIONS Pin Number 2 Pin Name Functional Description 1 to 3 A0 to A2 Device Address pins The MB85RC64 can be connected to the same data bus up to 8 devices. Device addresses are used in order to identify each of the devices. Connect these pins to VDD pin or VSS pin externally. Only if the combination of VDD and VSS pins matches a device, an address and a code inputted from the SDA pin, the device operates. In the open pin state, A0, A1, and A2 pins are pulled-down and recognized as “L”. 4 VSS Ground pin 5 SDA Serial Data I/O pin This is an I/O pin of serial data for performing bidirectional communication of address and writing or reading data of FRAM memory cell array. It is an open drain output that may be wired OR with other open drain or open collector signals on the bus, so a pull-up resistance is required to be connected to the external circuit. 6 SCL Serial Clock pin This is a clock input pin for input/output timing serial data. Data is sampled on the rising edge of the clock and output on the falling edge. 7 WP Write Protect pin When the Write Protect pin is “H”, the writing operation is disabled. When the Write Protect pin is “L”, the entire memory region can be overwritten. The reading operation is always enabled regardless of the Write Protect pin condition. In the open pin state, the Write Protect pin is pulled-down and recognized as “L”. 8 VDD Supply Voltage pin DS05–13109–3E MB85RC64 ■ BLOCK DIAGRAM Control Logic SCL WP Row Decoder Serial/Parallel Converter Address Counter SDA FRAM Array 8,192 × 8 Column Decoder/Sense Amp/ Write Amp A0, A1, A2 ■ I2C (Inter-Integrated Circuit) The MB85RC64 has the two-wire serial interface; the I2C bus,and operates as a slave device. The I2C bus defines communication roles of “master” and “slave” devices, with the master side holding the authority to initiate control. Furthermore, a I2C bus connection is possible where a single master device is connected to multiple slave devices in a party-line configuration. In this case, it is necessary to assign a unique device address to the slave device. • I2C Interface System Configuration Example VDD Pull-up Resistors SCL SDA I2C Bus Master I2C Bus MB85RC64 I2C Bus MB85RC64 I2C Bus MB85RC64 A2 0 A2 0 A2 0 A1 0 A0 0 A1 0 A0 1 A1 1 ... A0 0 Device address DS05–13109–3E 3 MB85RC64 ■ I2C COMMUNICATION PROTOCOL The I2C bus is a two wire serial interface that uses a bidirectional data bus (SDA) and serial clock (SCL). A data transfer can only be initiated by the bus master, which will also provide the serial clock for synchronization. The SDA signal should change while SCL is Low. However, as an exception, when starting and stopping communication sequence, SDA is allowed to change while SCL is High. • Start Condition To start read or write operations by the I2C bus, set the SDA input from High to Low while the SCL input is in High in order to start reading and writing. • Stop Condition Set the SDA input from Low to High while the SCL input is in High in order to terminate the I2C bus communication. Because the MB85RC64 does not need the writing wait time unlike E2PROM, it goes to the standby state immediately after the stop condition input. • Start Condition, Stop Condition SCL SDA Start Stop Note : The FRAM device does not need the programming wait time like tWC after issuing the Stop Condition such as. 4 DS05–13109–3E MB85RC64 ■ ACKNOWLEDGE (ACK) In the I2C bus, serial data including address or memory information is sent in units of 8 bits. The acknowledge signal indicates that every each 8 bits of the data is successfully sent and received. The information receiver side usually outputs “L” every time on the 9th SCL clock after each 8 bits are successfully transmitted. On the transmitter side, the bus is temporarily released to Hi-Z every time on this 9th clock to allow the acknowledge signal to be received and checked. During this Hi-Z-released period, the receiver side pulls the SDA line down to indicate “L” that the previous 8bits communication is successfully received. If the information receiver side detects Stop condition before driving the acknowledge “L”, the read operation ends and the I2C bus enters the standby state. If Stop condition is not sent, nor does the transmitter detect the acknowledge “L”, the bus remains in the released state “H” without doing anything. • Acknowledge timing overview diagram 1 SCL 2 3 8 SDA 9 ACK Start DS05–13109–3E The transmitter side should always release SDA on the 9th bit. At this time, the receiver side outputs a pull-down to indicate a successful byte transfer (ACK response). 5 MB85RC64 ■ DEVICE ADDRESS WORD (Slave address) Following the start condition, the bus master sends the 8bits device address word (Slave address) to start I2C communication. The device address word (8bits) consists of a device Type code (4bits), device address code (3bits), and a read/write code (1bit). • Device Type Code (4bits) The upper 4 bits of the device address word are a device type code that identifies the device type, and are fixed at “1010” for the MB85RC64. • Device Address Code (3bits) Following the device type code, the 3 bits of the device address code are input in order of A2, A1, and A0. Each MB85RC64 is given a unique 3bits code on the device address pin (external hardware pin A2, A1, and A0). When the device address code is received by the slave device, the slave only responds if the hardware device address of which is equal to its unique 3bits code. • Read/Write Code (1bit) The 8th bit of the device address word is the R/W (read/write) code. When the R/W code is “0”, a write operation is enabled, and the R/W code is “1”, a read operation is enabled for the MB85RC64. It turns to a stand-by state if the device code is not “1010” or device address code does not equal to pins A2, A1, and A0. 6 DS05–13109–3E MB85RC64 ■ DATA STRUCTURE In the I2C bus, the acknowledge “L” is output on the 9th bit after the 8 bits of the device and address word following the start condition. After confirming the acknowledge response at the slave, the I2C master outputs 8bits × 2 memory address to the I2C slave. When the memory address input ends, the slave again outputs the acknowledge “L”. After this operation, the I/O data follows in units of 8 bits, with the acknowledge “L” output after every 8bits. It is determined by the R/W code whether the data line is driven by the master or the slave. For a write operation the slave will accept 8bits from the master then send an acknowledge. If the master detects the acknowledge, the master will transfer the next 8bits. For a read operation the slave will place 8bits on the I2C bus, then wait for an acknowledge from the master. • Data Structure Diagram Start 1 2 3 4 5 6 7 8 9 1 2 .. SCL SDA ACK S 1 0 1 0 A2 A1 A0 R/W A .. Access from master Access from slave S Start Condition A ACK ■ FRAM ACKNOWLEDGE -- POLLING NOT REQUIRED The MB85RC64 performs write operations at the same speed as read operations, so any waiting time for an ACK polling* does not occur. The write cycle takes no additional time. *: As to E2PROM, the Acknowledge Polling is performed as a progress check in the write programming step. It places NAK condition on the bus as of “not acknowledged” during the writing programming period. The busy status for the write programming is given from 9th ACK bit. That “done” condition is placed onto I2C bus by E2PROM I2C device and your program had to poll the bus in order to sense that condition. ■ WRITE PROTECT (WP) The entire memory array can be write protected using the Write Protect pin. When the Write Protect pin is set to “H”, the entire memory map will be write protected. When the Write Protect pin is “L”, all addresses may be overwritten. Reading is allowed regardless of the WP pin's High/Low. Note : The Write Protect pin is pulled down internally to VSS pin, therefore if the Write Protect pin is open, the pin status is detected as Low (write enabled). DS05–13109–3E 7 MB85RC64 ■ COMMAND • Byte Write If the 8th bit of the device address word (R/W = 0) is sent following the start condition, the slave responds with an ACK. After this ACK, write addresses and data are sent in the same way, and the write ends by master, generating a stop condition at the end. S 1 0 1 0 A2 A1 A0 0 A Address High 8bits A 0 00XXXXX Address Low 8bits A Write Data 8bits A P X X X X X X XX Access from master MSB LSB Access from slave S Start Condition P Stop Condition A ACK Note : In the MB85RC64, input “000” as the upper 3 bits of the MSB. • Page Write If additional 8bits are sent after the same command as Byte Write, a page write is performed. If more bytes are sent than will fit up to the end of the address, the address rolls over to 0000H. Therefore, if more than 8KBytes are sent, the data is overwritten in order starting from the start of the FRAM memory address that was written first. Because FRAM performs write operations at bus speed, the data will be written to FRAM after the ACK response finishes immediately. S 1 0 1 0 A2 A1 A0 0 A Address High 8bits A Address Low 8bits A Write Data 8bits A Write Data ... A P Access from master Access from slave S Start Condition P Stop Condition A ACK Note : It is not necessary to take a period for internal write operation cycles from the buffer to the memory after the stop condition is generated. 8 DS05–13109–3E MB85RC64 • Current Address Read When the previous write or read operation finishes successfully up to the stop command and if the last accessed address is taken to be “n”, then the address at “n+1” is read by sending the following command unless turning the power off. If the end of the address range is reached internally, the address counter will roll over to 0000H. The current address is undefined immediately after the power is turned on. Access from master Access from slave S Start Condition (n+1) address S 1 0 1 0 A2 A1 A0 1 A Read Data 8bits N P P Stop Condition A ACK N NACK • Random Read The one byte of data at the address as saved in the buffer can be read out synchronously to SCL by specifying the address in the same way as for a write, and then issuing another start condition and sending the Control Byte (R/W = 1). The final NACK is issued by the receiver that receives the data. In this case, this bit is issued by the master side. n address S 1 0 1 0 A2 A1 A0 0 A Address High 8bits A Address Low 8bits A S 1 0 1 0 A2 A1 A0 1 A Read Data 8bits N P Access from master Access from slave S Start Condition P Stop Condition A ACK N NACK DS05–13109–3E 9 MB85RC64 • Sequential Read Data can be received continuously following the control byte after specifying the address the same as for Random Read. If the read reaches the end of address for the MB85RC64, the internal read address automatically rolls over to 0000H. ... A Read Data 8bits A Read Data ... A Read Data 8bits N P Access from master Access from slave P Stop Condition A ACK N NACK 10 DS05–13109–3E MB85RC64 ■ ABSOLUTE MAXIMUM RATINGS Parameter Rating Symbol Min Max Unit Power supply voltage* VCC − 0.5 +4.0 V Input pin voltage* VIN − 0.5 VCC + 0.5 ( ≤ 4.0) V VOUT − 0.5 VCC + 0.5 ( ≤ 4.0) V Ambient temperature TA − 40 + 85 °C Storage temperature Tstg − 40 + 125 °C Output pin voltage* *: These parameters are based on the condition that VSS is 0 V. WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings. ■ RECOMMENDED OPERATING CONDITIONS Parameter Symbol Value Min Typ Max Unit Power supply voltage* VCC 2.7 3.3 3.6 V “H” level input voltage* VIH VCC × 0.8 ⎯ VCC + 0.5 ( ≤ 4.0) V “L” level input voltage* VIL − 0.5 ⎯ + 0.6 V Ambient temperature TA − 40 ⎯ + 85 °C *: These parameters are based on the condition that VSS is 0 V. WARNING: The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the device's electrical characteristics are warranted when the device is operated within these ranges. Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their representatives beforehand. DS05–13109–3E 11 MB85RC64 ■ ELECTRICAL CHARACTERISTICS 1. DC Characteristics (within recommended operating conditions) Parameter Symbol Condition Input leakage current |ILI| Output leakage current Value Unit Min Typ Max SCL, SDA = 0 V to VCC A0, A1, A2, WP = 0 V or VCC ⎯ ⎯ 1 μA |ILO| VOUT = 0 V to VCC ⎯ ⎯ 1 μA Operating power supply current ICC SCL = 400 kHz ⎯ 100 150 μA Standby current ISB SCL, SDA = VCC A0, A1, A2, WP = 0 V or VCC ⎯ 5 20 μA “L” level output voltage VOL IOL = 2 mA ⎯ ⎯ 0.4 V 2. AC Characteristics Parameter Symbol Value Min Max Unit SCL clock frequency FSCL 0 400 kHz Clock high time THIGH 600 ⎯ ns Clock low time TLOW 1300 ⎯ ns SCL/SDA rise time Tr ⎯ 300 ns SCL/SDA fall time Tf ⎯ 300 ns Start condition hold THD:STA 600 ⎯ ns Start condition setup TSU:STA 600 ⎯ ns SDA input hold THD:DAT 0 ⎯ ns SDA input setup TSU:DAT 100 ⎯ ns SDA output hold TDH:DAT 0 ⎯ ns Stop condition setup TSU:STO 600 ⎯ ns SDA output access after SCL fall TAA ⎯ 900 ns Pre-charge time TBUF 1300 ⎯ ns 50 ns Pulse width ignored ⎯ TSP (Input Filter on SCL and SDA) AC characteristics were measured under the following measurement conditions. Power supply voltage : 2.7 V to 3.6 V Operating temperature : − 40 °C to + 85 °C Input voltage magnitude : 0.3 V to 2.7 V 12 Input rise time : 5 ns Input fall time : 5 ns Input judge level : VCC/2 Output judge level : VCC/2 DS05–13109–3E MB85RC64 3. AC Timing Definitions TSU:DAT SCL VIH VIL SDA Start THD:DAT VIH VIH VIH VIH VIL VIL VIL VIL VIH VIH VIH VIH VIL VIL VIL VIL TSU:STA THD:STA TSU:STO Tr THIGH SCL Stop VIH Tf TLOW VIH VIL VIL VIH VIH VIL VIL VIH SDA Stop VIH VIL Start VIH VIL VIH VIL VIL Tbuf Tr T TDH:DAT f Taa Tsp VIH SCL VIL VIL VIH SDA VIL Valid VIH VIL VIL 1/FSCL 4. Pin Capacitance Parameter Symbol Conditions I/O capacitance CI/O Input capacitance CIN VIN = VOUT = 0 V, f = 1 MHz, TA = + 25 °C Value Unit Min Typ Min ⎯ ⎯ 15 pF ⎯ ⎯ 15 pF 5. AC Test Load Circuit 3.3 V Output 100 pF DS05–13109–3E 13 MB85RC64 ■ POWER ON SEQUENCE tr tpd tpu VCC VCC 2.7 V 2.7 V VIH (Min) VIH (Min) 1.0 V 1.0 V VIL (Max) VIL (Max) 0V 0V SDA, SCL SDA, SCL >VCC × 0.8 * SDA, SCL : Don't care SDA, SCL >VCC × 0.8 * SDA, SCL * : SDA, SCL (Max) < VCC + 0.5 V Parameter Symbol SDA, SCL level hold time during power down SDA, SCL level hold time during power up Power supply rise time Value Unit Min Max tpd 85 ⎯ ns tpu 85 ⎯ ns tr 10 ⎯ μs ■ NOTES ON USE • Data written before performing IR reflow is not guaranteed. • VDD pin is required to be rising from 0 V because turning the power on from an intermediate level may cause malfunctions, when the power is turned on. During the access period from the start condition to the stop condition, keep the level of WP, A0, A1, and A2 pins to “H” or “L”. 14 DS05–13109–3E MB85RC64 ■ ORDERING INFORMATION Part number Package MB85RC64PNF-G-JNE1 8-pin, plastic SOP (FPT-8P-M02) MB85RC64PNF-G-JNERE1 8-pin, plastic SOP (FPT-8P-M02) DS05–13109–3E Remarks Embossed Carrier tape 15 MB85RC64 ■ PACKAGE DIMENSION 8-pin plastic SOP Lead pitch 1.27 mm Package width × package length 3.9 mm × 5.05 mm Lead shape Gullwing Sealing method Plastic mold Mounting height 1.75 mm MAX Weight 0.06 g (FPT-8P-M02) 8-pin plastic SOP (FPT-8P-M02) +0.25 Note 1) *1 : These dimensions include resin protrusion. Note 2) *2 : These dimensions do not include resin protrusion. Note 3) Pins width and pins thickness include plating thickness. Note 4) Pins width do not include tie bar cutting remainder. +.010 +0.03 *1 5.05 –0.20 .199 –.008 0.22 –0.07 +.001 .009 –.003 8 5 *2 3.90±0.30 6.00±0.40 (.154±.012) (.236±.016) Details of "A" part 45° 1.55±0.20 (Mounting height) (.061±.008) 0.25(.010) 0.40(.016) 1 "A" 4 1.27(.050) 0.44±0.08 (.017±.003) 0.13(.005) 0~8° M 0.50±0.20 (.020±.008) 0.60±0.15 (.024±.006) 0.15±0.10 (.006±.004) (Stand off) 0.10(.004) C 2002-2010 FUJITSU SEMICONDUCTOR LIMITED F08004S-c-4-9 Dimensions in mm (inches). Note: The values in parentheses are reference values. Please check the latest package dimension at the following URL. http://edevice.fujitsu.com/package/en-search/ 16 DS05–13109–3E MB85RC64 MEMO DS05–13109–3E 17 MB85RC64 MEMO 18 DS05–13109–3E MB85RC64 MEMO DS05–13109–3E 19 MB85RC64 FUJITSU SEMICONDUCTOR LIMITED Nomura Fudosan Shin-yokohama Bldg. 10-23, Shin-yokohama 2-Chome, Kohoku-ku Yokohama Kanagawa 222-0033, Japan Tel: +81-45-415-5858 http://jp.fujitsu.com/fsl/en/ For further information please contact: North and South America FUJITSU SEMICONDUCTOR AMERICA, INC. 1250 E. Arques Avenue, M/S 333 Sunnyvale, CA 94085-5401, U.S.A. Tel: +1-408-737-5600 Fax: +1-408-737-5999 http://us.fujitsu.com/micro/ Asia Pacific FUJITSU SEMICONDUCTOR ASIA PTE. LTD. 151 Lorong Chuan, #05-08 New Tech Park 556741 Singapore Tel : +65-6281-0770 Fax : +65-6281-0220 http://www.fujitsu.com/sg/services/micro/semiconductor/ Europe FUJITSU SEMICONDUCTOR EUROPE GmbH Pittlerstrasse 47, 63225 Langen, Germany Tel: +49-6103-690-0 Fax: +49-6103-690-122 http://emea.fujitsu.com/semiconductor/ FUJITSU SEMICONDUCTOR SHANGHAI CO., LTD. Rm. 3102, Bund Center, No.222 Yan An Road (E), Shanghai 200002, China Tel : +86-21-6146-3688 Fax : +86-21-6335-1605 http://cn.fujitsu.com/fss/ Korea FUJITSU SEMICONDUCTOR KOREA LTD. 902 Kosmo Tower Building, 1002 Daechi-Dong, Gangnam-Gu, Seoul 135-280, Republic of Korea Tel: +82-2-3484-7100 Fax: +82-2-3484-7111 http://kr.fujitsu.com/fsk/ FUJITSU SEMICONDUCTOR PACIFIC ASIA LTD. 10/F., World Commerce Centre, 11 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel : +852-2377-0226 Fax : +852-2376-3269 http://cn.fujitsu.com/fsp/ Specifications are subject to change without notice. For further information please contact each office. All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with sales representatives before ordering. The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of FUJITSU SEMICONDUCTOR device; FUJITSU SEMICONDUCTOR does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. FUJITSU SEMICONDUCTOR assumes no liability for any damages whatsoever arising out of the use of the information. Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU SEMICONDUCTOR or any third party or does FUJITSU SEMICONDUCTOR warrant non-infringement of any third-party's intellectual property right or other right by using such information. FUJITSU SEMICONDUCTOR assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that FUJITSU SEMICONDUCTOR will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of overcurrent levels and other abnormal operating conditions. Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations of the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws. The company names and brand names herein are the trademarks or registered trademarks of their respective owners. Edited: Sales Promotion Department