ONSEMI MC33275DT-3.0G

MC33275, NCV33275
300 mA, Low Dropout
Voltage Regulator
The MC33275 series are micropower low dropout voltage
regulators available in a wide variety of output voltages as well as
packages, SOT−223, SOP−8, DPAK, and DFN 4x4 surface mount
packages. These devices feature a very low quiescent current and are
capable of supplying output currents up to 300 mA. Internal current
and thermal limiting protection are provided by the presence of a short
circuit at the output and an internal thermal shutdown circuit.
Due to the low input−to−output voltage differential and bias current
specifications, these devices are ideally suited for battery powered
computer, consumer, and industrial equipment where an extension of
useful battery life is desirable.
http://onsemi.com
LOW DROPOUT
MICROPOWER VOLTAGE
REGULATOR
MARKING
DIAGRAMS
Features
• Low Input−to−Output Voltage Differential of 25 mV at IO = 10 mA,
•
•
•
•
•
and 260 mV at IO = 300 mA
Extremely Tight Line and Load Regulation
Stable with Output Capacitance of only 0.33 F for 2.5 V Output
Voltage
Internal Current and Thermal Limiting
NCV Prefix for Automotive and Other Applications Requiring Site
and Control Changes
Pb−Free Packages are Available
4
SOT−223
ST SUFFIX
CASE 318E
1
3
AYW
275xxG
G
1
8
275xx
ALYW
G
SOIC−8
D SUFFIX
CASE 751
8
1
1
Applications
• Battery Powered Consumer Products
• Hand−Held Instruments
• Camcorders and Cameras
4
1
DPAK−3
DT SUFFIX
CASE 369A
275xxG
ALYWW
3
Vin
1
Vout
Thermal &
Anti−sat
Protection
1
DFN−8, 4x4
MN SUFFIX
CASE 488AF
1
275xx
ALYWG
G
xx
= Voltage Version
A
= Assembly Location
L
= Wafer Lot
Y
= Year
W, WW = Work Week
G or G = Pb−Free Device
(Note: Microdot may be in either location)
Rint
1.23 V
V. Ref.
54 K
GND
This device contains 41 active transistors
ORDERING INFORMATION
Figure 1. Simplified Block Diagram
See detailed ordering and shipping information in the
package dimensions section on page 10 of this data sheet.
© Semiconductor Components Industries, LLC, 2005
December, 2005 − Rev. 15
1
Publication Order Number:
MC33275/D
MC33275, NCV33275
PIN CONNECTIONS
GND
GND
4
4
Input
GND
1
2
3
Vin GND Vout
MC33275ST
GND
1
2
3
VinGND Vout
MC33275DT
N/C
1
ÇÇ
ÇÇ
ÇÇ
8
Output
7
GND
6
GND
5
N/C
2
3
4
Input
Input
Input
N/C
Pins 4 and 5 Not Connected
MC33275D
1
2
3
4
Ç
Ç
Ç
8
7
6
5
Output
N/C
GND
N/C
MC33275MN
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
VCC
13
Vdc
PD
Internally Limited
W
RJA
RJC
160
25
°C/W
°C/W
RJA
RJC
245
15
°C/W
°C/W
RJA
RJC
92
6.0
°C/W
°C/W
RJA
RJA
psi−JC*
183
93
9.0
°C/W
°C/W
°C/W
Output Current
IO
300
mA
Maximum Junction Temperature
TJ
150
°C
Operating Ambient Temperature Range
TA
− 40 to +125
°C
Storage Temperature Range
Tstg
− 65 to +150
°C
Electrostatic Discharge Sensitivity (ESD)
Human Body Model (HBM)
Machine Model (MM)
ESD
Input Voltage
Power Dissipation and Thermal Characteristics
TA = 25°C
Maximum Power Dissipation
Case 751 (SOIC−8) D Suffix
Thermal Resistance, Junction−to−Ambient
Thermal Resistance, Junction−to−Case
Case 318E (SOT−223) ST Suffix
Thermal Resistance, Junction−to−Air
Thermal Resistance, Junction−to−Case
Case 369A (DPAK−3) DT Suffix
Thermal Resistance, Junction−to−Air
Thermal Resistance, Junction−to−Case
Case 488AF (DFN−8, 4x4) MN Suffix
Thermal Resistance, Junction−to−Air (with 1.0 oz PCB cu area)
Thermal Resistance, Junction−to−Air (with 1.8 oz PCB cu area)
Thermal Resistance, Junction−to−Case
V
4000
400
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit
values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
*“C’’ (“case’’) is defined as the solder−attach interface between the center of the exposed pad on the bottom of the package, and the board to
which it is attached.
http://onsemi.com
2
MC33275, NCV33275
ELECTRICAL CHARACTERISTICS (CL = 1.0F, TA = 25°C, for min/max values TJ = −40°C to +125°C, Note 1)
Symbol
Characteristic
Output Voltage
2.5 V Suffix
3.0 V Suffix
3.3 V Suffix
5.0 V Suffix
IO = 0 mA to 250 mA
TA = 25°C, Vin = [VO + 1] V
Min
Typ
Max
2.475
2.970
3.267
4.950
2.50
3.00
3.30
5.00
2.525
3.030
3.333
5.05
2.450
2.940
3.234
4.900
−
−
−
−
2.550
3.060
3.366
5.100
VO
Unit
Vdc
2.5 V Suffix
3.0 V Suffix
3.3 V Suffix
5.0 V Suffix
Vin = [VO + 1] V, 0 < IO < 100 mA
2% Tolerance from TJ = −40 to +125°C
Line Regulation
Vin = [VO + 1] V to 12 V, IO = 250 mA,
All Suffixes TA = 25°C
Regline
−
2.0
10
mV
Load Regulation
Vin = [VO + 1] V, IO = 0 mA to 250 mA,
All Suffixes TA = 25°C
Regload
−
5.0
25
mV
−
−
−
−
25
115
220
260
100
200
400
500
65
75
−
−
−
160
46
−
−
−
125
200
−
−
−
−
1100
1500
1500
1500
1500
2000
2000
2000
ILIMIT
−
450
−
mA
−
−
150
−
°C
Dropout Voltage
IO = 10 mA
IO = 100 mA
IO = 250 mA
IO = 300 mA
Vin − VO
TJ = −40°C to +125°C
Ripple Rejection (120 Hz)
Vin(peak−peak) = [VO + 1.5] V to [VO + 5.5] V
Output Noise Voltage
CL = 1.0 F
IO = 50 mA (10 Hz to 100 kHz)
CL = 200 F
−
mV
dB
Vrms
Vn
CURRENT PARAMETERS
Quiescent Current ON Mode
Vin = [VO + 1] V, IO = 0 mA
IQOn
Quiescent Current ON Mode SAT
2.5 V Suffix
3.0 V Suffix
3.3 V Suffix
5.0 V Suffix
Vin = [VO − 0.5] V, IO = 0 mA (Note 2)
IQSAT
Current Limit
Vin = [VO + 1] V, VO Shorted
A
A
THERMAL SHUTDOWN
Thermal Shutdown
1. Low duty pulse techniques are used during test to maintain junction temperature as close to ambient as possible.
2. Quiescent Current is measured where the PNP pass transistor is in saturation. Vin = [VO − 0.5] V guarantees this condition.
http://onsemi.com
3
MC33275, NCV33275
DEFINITIONS
difference between the input power (VCC X ICC) and the
output power (Vout X Iout) is increasing.
Depending on ambient temperature, it is possible to
calculate the maximum power dissipation and so the
maximum current as following:
Load Regulation − The change in output voltage for a
change in load current at constant chip temperature.
Dropout Voltage − The input/output differential at which
the regulator output no longer maintains regulation against
further reductions in input voltage. Measured when the
output drops 100 mV below its nominal value (which is
measured at 1.0 V differential), dropout voltage is affected
by junction temperature, load current and minimum input
supply requirements.
Output Noise Voltage − The RMS AC voltage at the
output with a constant load and no input ripple, measured
over a specified frequency range.
Maximum Power Dissipation − The maximum total
dissipation for which the regulator will operate within
specifications.
Quiescent Current − Current which is used to operate the
regulator chip and is not delivered to the load.
Line Regulation − The change in output voltage for a
change in the input voltage. The measurement is made under
conditions of low dissipation or by using pulse techniques
such that the average chip temperature is not significantly
affected.
Maximum Package Power Dissipation − The maximum
package power dissipation is the power dissipation level at
which the junction temperature reaches its maximum value
i.e. 150°C. The junction temperature is rising while the
T –T
Pd + J A
R
JA
The maximum operating junction temperature TJ is
specified at 150°C, if TA = 25°C, then PD can be found. By
neglecting the quiescent current, the maximum power
dissipation can be expressed as:
I out +
P
D
V – Vout
CC
The thermal resistance of the whole circuit can be
evaluated by deliberately activating the thermal shutdown
of the circuit (by increasing the output current or raising the
input voltage for example).
Then you can calculate the power dissipation by
subtracting the output power from the input power. All
variables are then well known: power dissipation, thermal
shutdown temperature and ambient temperature.
R
http://onsemi.com
4
JA
T –T
+ J A
P
D
MC33275, NCV33275
7
150
TA = 25° C
6 CL = 33 F
IL = 10 mA
5 Vout = 3.3 V
100
4
50
3
0
2
Vout
−50
1
0
0
20
40
60
80
100
120
140
160
70
60
Vin
40
4
30
3
20
10
2
0
1
Vout
0
50
100
Figure 3. Line Transient Response
1.0
300
−200
0
Vout
CHANGE
−400 CL = 1.0 F
Vout = 3.3 V
−500 TA = 25° C
−600 Vin = 4.3 V
0
50
−0.2
−0.4
−0.6
−0.8
100
150
200
300
250
350
LOAD CURRENT (mA)
LOAD CURRENT (mA)
0.2
150
LOAD CURRENT
−50
0.04
−150
−0.01
−250
−350
CL = 33.0 F
Vout = 3.3 V
TA = 25° C
Vin = 4.3 V
Vout
CHANGE
−450
−550
−0.06
−0.11
−650
−750
−1.0
400
−0.16
0
50
TIME (S)
100
150
200
250
300
TIME (S)
Figure 5. Load Transient Response
Figure 4. Load Transient Response
300
3.5
3.0
IL = 1 mA
DROPOUT VOLTAGE (mV)
OUTPUT VOLTAGE (V)
0.09
50
OUTPUT VOLTAGE CHANGE (V)
0.4
−100
0.14
250
0.6
LOAD
CURRENT
OUTPUT VOLTAGE CHANGE (V)
200
−700
350
0.8
−300
−20
200
150
TIME (S)
Figure 2. Line Transient Response
0
−10
0
−100
180 200
TIME (S)
100
50
Vin , INPUT VOLTAGE (V)
Vin
200
OUTPUT VOLTAGE CHANGE (mV)
TA = 25° C
6 CL = 0.47 F
IL = 10 mA
5 Vout = 3.3 V
OUTPUT VOLTAGE CHANGE (mV)
Vin , INPUT VOLTAGE (V)
7
2.5
IL = 250 mA
2.0
1.5
1.0
250
200
150
100
50
0.5
0
0
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
1
4.5 5.0
10
100
1000
INPUT VOLTAGE (V)
IO, OUTPUT CURRENT (mA)
Figure 6. Output Voltage versus Input Voltage
Figure 7. Dropout Voltage versus Output Current
http://onsemi.com
5
MC33275, NCV33275
12
250
10
IL = 300 mA
8
200
Ignd (mA)
DROPOUT VOLTAGE (mV)
300
IL = 250 mA
150
IL = 100 mA
100
IL = 300 mA
6
4
IL = 100 mA
50
2
IL = 10 mA
0
−40
0
IL = 50 mA
25
0
85
0
1
2
3
TEMPERATURE (°C)
4
5
6
7
8
Vin (VOLTS)
Figure 9. Ground Pin Current versus
Input Voltage
Figure 8. Dropout Voltage versus Temperature
2.5
8
7
IO = 0
2.495
IL = 250 mA
Vout (VOLTS)
Ignd (mA)
6
5
4
3
2.49
IO = 250 mA
2.485
IL = 100 mA
2.48
IL = 50 mA
2.475
2
1
0
−40
−20
0
20
40
60
80
100
120
2.47
−40
140
0
25
TA (°C)
TEMPERATURE (°C)
Figure 10. Ground Pin Current versus
Ambient Temperature
Figure 11. Output Voltage versus Ambient
Temperature (Vin = Vout + 1V)
http://onsemi.com
6
85
MC33275, NCV33275
2.5
IO = 0
2.495
Vout (VOLTS)
2.49
IO = 250 mA
2.485
2.48
2.475
2.47
2.465
−40
0
25
85
TEMPERATURE (°C)
Figure 12. Output Voltage versus Ambient
Temperature (Vin = 12 V)
70
70
60
60
50
IL = 250 mA
IL = 1 mA
40
dB
dB
50
40
30
30
20
20
10
10
0
0.1
IL = 100 mA
IL = 10 mA
1
10
0
0.1
100
1
10
FREQUENCY (kHz)
FREQUENCY (kHz)
Figure 13. Ripple Rejection
Figure 14. Ripple Rejection
http://onsemi.com
7
100
MC33275, NCV33275
APPLICATIONS INFORMATION
Vou
Vin
t
Cin
Cout
LOAD
GND
Figure 15. Typical Application Circuit
The MC33275 regulators are designed with internal
current limiting and thermal shutdown making them
user−friendly. Figure 15 is a typical application circuit. The
output capability of the regulator is in excess of 300 mA,
with a typical dropout voltage of less than 260 mV. Internal
protective features include current and thermal limiting.
100
ESR (ohm)
Vout = 3.0 V
Cout = 1.0 F
Cin = 1.0 F
EXTERNAL CAPACITORS
10
Stable Region
1.0
These regulators require only a 0.33 F (or greater)
capacitance between the output and ground for stability for
1.8 V, 2.5 V, 3.0 V, and 3.3 V output voltage options. Output
voltage options of 5.0 V require only 0.22 F for stability.
The output capacitor must be mounted as close as possible
to the MC33275. If the output capacitor must be mounted
further than two centimeters away, then a larger value of
output capacitor may be required for stability. A value of
0.68 F or larger is recommended. Most type of aluminum,
tantalum, or multilayer ceramic will perform adequately.
Solid tantalums or appropriate multilayer ceramic
capacitors are recommended for operation below 25°C. An
input bypass capacitor is recommended to improve transient
response or if the regulator is connected to the supply input
filter with long wire lengths, more than 4 inches. This will
reduce the circuit’s sensitivity to the input line impedance at
high frequencies. A 0.33 F or larger tantalum, mylar,
ceramic, or other capacitor having low internal impedance
at high frequencies should be chosen. The bypass capacitor
should be mounted with shortest possible lead or track
length directly across the regulator’s input terminals.
Figure 16 shows the ESR that allows the LDO to remain
stable for various load currents.
0.1
0
50
100
150
200
250
300
LOAD CURRENT (mA)
Figure 16. ESR for Vout = 3.0V
Applications should be tested over all operating
conditions to insure stability.
THERMAL PROTECTION
Internal thermal limiting circuitry is provided to protect
the integrated circuit in the event that the maximum junction
temperature is exceeded. When activated, typically at
150°C, the output is disabled. There is no hysteresis built
into the thermal protection. As a result the output will appear
to be oscillating during thermal limit. The output will turn
off until the temperature drops below the 150°C then the
output turns on again. The process will repeat if the junction
increases above the threshold. This will continue until the
existing conditions allow the junction to operate below the
temperature threshold.
Thermal limit is not a substitute for proper
heatsinking.
The internal current limit will typically limit current to
450 mA. If during current limit the junction exceeds 150°C,
the thermal protection will protect the device also. Current
limit is not a substitute for proper heatsinking.
OUTPUT NOISE
In many applications it is desirable to reduce the noise
present at the output. Reducing the regulator bandwidth by
increasing the size of the output capacitor will reduce the noise.
http://onsemi.com
8
RJA, THERMAL RESISTANCE,
JUNCTION−TO−AIR (°CW)
180
1.6
160
1.4
PD(max) for TA = 50°C
140
ÎÎÎ
ÎÎÎ
ÎÎÎ
Minimum
Size Pad
120
1.2
2.0 oz. Copper
L
1.0
L
100
80
0.8
0.6
RJA
60
0
5.0
0.4
30
10
15
20
25
L, LENGTH OF COPPER (mm)
PD, MAXIMUM POWER DISSIPATION (W)
MC33275, NCV33275
1.6
RJA, THERMAL RESISTANCE,
JUNCTION−TO−AIR (°CW)
100
PD(max) for TA = 50°C
1.4
90
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
2.0 oz. Copper
L
80
Minimum
Size Pad
70
1.0
L
60
1.2
0.8
50
0.6
RJA
40
0
5.0
10
15
20
0.4
30
25
PD, MAXIMUM POWER DISSIPATION (W)
Figure 17. SOT−223 Thermal Resistance and Maximum
Power Dissipation versus P.C.B. Copper Length
L, LENGTH OF COPPER (mm)
3.2
RJA, THERMAL RESISTANCE,
JUNCTION−TO−AIR (°CW)
170
150
2.8
PD(max) for TA = 50°C
2.4
130
110
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
Graph Represents Symmetrical Layout 2.0
90
2.0 oz.
Copper
L
70
RJA
50
1.6
1.2
3.0
mm
L
0.8
0.4
30
0
10
20
30
40
50
L, LENGTH OF COPPER (mm)
Figure 19. SOP−8 Thermal Resistance and Maximum
Power Dissipation versus P.C.B. Copper Length
http://onsemi.com
9
PD, MAXIMUM POWER DISSIPATION (W)
Figure 18. DPAK Thermal Resistance and Maximum
Power Dissipation versus P.C.B. Copper Length
MC33275, NCV33275
ORDERING INFORMATION
Operating Temperature
Range, Tolerance
Case
Package
Marking
Shipping†
MC33275D−2.5
751
SOIC−8
27525
98 Units/Rail
MC33275D−2.5G
751
SOIC−8
(Pb−Free)
27525
98 Units/Rail
MC33275D−2.5R2
751
SOIC−8
27525
2500/Tape & Reel
MC33275D−2.5R2G
751
SOIC−8
(Pb−Free)
27525
2500/Tape & Reel
369A
DPAK
27525
75 Units/Rail
369A
DPAK
(Pb−Free)
27525G
75 Units/Rail
MC33275DT−2.5RK
369A
DPAK
27525
2500/Tape & Reel
MC33275DT−2.5RKG
369A
DPAK
(Pb−Free)
27525G
2500/Tape & Reel
MC33275MN−2.5R2G
488AF
DFN8
(Pb−Free)
27525
3000/Tape & Reel
318E
SOT−223
27525
4000/Tape & Reel
318E
SOT−223
(Pb−Free)
27525
4000/Tape & Reel
751
SOIC−8
27530
98 Units/Rail
751
SOIC−8
(Pb−Free)
27530
98 Units/Rail
751
SOIC−8
27530
2500/Tape & Reel
751
SOIC−8
(Pb−Free)
27530
2500/Tape & Reel
369A
DPAK
27530
75 Units/Rail
369A
DPAK
(Pb−Free)
27530G
75 Units/Rail
MC33275DT−3.0RK
369A
DPAK
27530
2500/Tape & Reel
MC33275DT−3.0RKG
369A
DPAK
(Pb−Free)
27530G
2500/Tape & Reel
MC33275MN−3.0R2G
488AF
DFN8
(Pb−Free)
27530
3000/Tape & Reel
MC33275ST−3.0T3
318E
SOT−223
27530
4000/Tape & Reel
MC33275ST−3.0T3G
318E
SOT−223
(Pb−Free)
27530
4000/Tape & Reel
Device
VO Typ (V)
MC33275DT−2.5
MC33275DT−2.5G
2.5 V
(Fixed Voltage)
1% Tolerance
at TA = 25°C
MC33275ST−2.5T3
MC33275ST−2.5T3G
MC33275D−3.0
MC33275D−3.0G
2% Tolerance at
TJ from −40°C to +125°C
MC33275D−3.0R2
MC33275D−3.0R2G
MC33275DT−3.0
MC33275DT−3.0G
3.0 V
(Fixed Voltage)
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
10
MC33275, NCV33275
ORDERING INFORMATION (continued)
Operating Temperature
Range, Tolerance
Case
Package
Marking
Shipping†
MC33275D−3.3
751
SOIC−8
27533
98 Units/Rail
MC33275D−3.3G
751
SOIC−8
(Pb−Free)
27533
98 Units/Rail
MC33275D−3.3R2
751
SOIC−8
27533
2500/Tape & Reel
MC33275D−3.3R2G
751
SOIC−8
(Pb−Free)
27533
2500/Tape & Reel
369A
DPAK
27533
75 Units/Rail
369A
DPAK
(Pb−Free)
27533G
75 Units/Rail
MC33275DT−3.3RK
369A
DPAK
27533
2500/Tape & Reel
MC33275DT−3.3RKG
369A
DPAK
(Pb−Free)
27533G
2500/Tape & Reel
318E
SOT−223
27533
4000/Tape & Reel
318E
SOT−223
(Pb−Free)
27533
4000/Tape & Reel
488AF
DFN−8
(Pb−Free)
27330
3000/Tape & Reel
751
SOIC−8
27550
98 Units/Rail
751
SOIC−8
(Pb−Free)
27550
98 Units/Rail
751
SOIC−8
27550
2500/Tape & Reel
751
SOIC−8
(Pb−Free)
27550
2500/Tape & Reel
MC33275DT−5.0
369A
DPAK
27550
75 Units/Rail
MC33275DT−5.0G
369A
DPAK
(Pb−Free)
27550G
75 Units/Rail
369A
DPAK
27550
2500/Tape & Reel
369A
DPAK
(Pb−Free)
27550G
2500/Tape & Reel
MC33275MN−5.0R2
488AF
DFN−8
27550
3000/Tape & Reel
MC33275MN−5.0R2G
488AF
DFN−8
(Pb−Free)
27550
3000/Tape & Reel
MC33275ST−5.0T3
318E
SOT−223
27550
4000/Tape & Reel
MC33275ST−5.0T3G
318E
SOT−223
(Pb−Free)
27550
4000/Tape & Reel
NCV33275ST−5.0T3
318E
SOT−223
27550
4000/Tape & Reel
NCV33275ST−5.0T3G
318E
SOT−223
(Pb−Free)
27550
4000/Tape & Reel
Device
VO Typ (V)
MC33275DT−3.3
MC33275DT−3.3G
3.3 V
(Fixed Voltage)
MC33275ST−3.3T3
1% Tolerance
at TA = 25°C
MC33275ST−3.3T3G
MC33275MN−3.3R2G
MC33275D−5.0
MC33275D−5.0G
2% Tolerance at
TJ from −40°C to +125°C
1% Tolerance
at TA = 25°C
MC33275D−5.0R2
MC33275D−5.0R2G
MC33275DT−5.0RK
5.0 V
(Fixed Voltage)
MC33275DT−5.0RKG
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
11
MC33275, NCV33275
PACKAGE DIMENSIONS
SOT−223 (TO−261)
ST SUFFIX
CASE 318E−04
ISSUE K
A
F
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
4
S
1
2
INCHES
DIM MIN
MAX
A
0.249
0.263
B
0.130
0.145
C
0.060
0.068
D
0.024
0.035
F
0.115
0.126
G
0.087
0.094
H 0.0008 0.0040
J
0.009
0.014
K
0.060
0.078
L
0.033
0.041
M
0_
10 _
S
0.264
0.287
B
3
D
L
G
J
C
0.08 (0003)
M
H
K
SOLDERING FOOTPRINT*
3.8
0.15
2.0
0.079
2.3
0.091
2.3
0.091
6.3
0.248
2.0
0.079
1.5
0.059
SCALE 6:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
12
MILLIMETERS
MIN
MAX
6.30
6.70
3.30
3.70
1.50
1.75
0.60
0.89
2.90
3.20
2.20
2.40
0.020
0.100
0.24
0.35
1.50
2.00
0.85
1.05
0_
10 _
6.70
7.30
MC33275, NCV33275
PACKAGE DIMENSIONS
SOIC−8 NB
D SUFFIX
CASE 751−07
ISSUE AG
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
−X−
A
8
5
S
B
1
0.25 (0.010)
M
Y
M
4
K
−Y−
G
C
N
DIM
A
B
C
D
G
H
J
K
M
N
S
X 45 _
SEATING
PLANE
−Z−
0.10 (0.004)
H
D
0.25 (0.010)
M
Z Y
S
X
M
J
S
SOLDERING FOOTPRINT*
1.52
0.060
7.0
0.275
4.0
0.155
0.6
0.024
1.270
0.050
SCALE 6:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
13
MILLIMETERS
MIN
MAX
4.80
5.00
3.80
4.00
1.35
1.75
0.33
0.51
1.27 BSC
0.10
0.25
0.19
0.25
0.40
1.27
0_
8_
0.25
0.50
5.80
6.20
INCHES
MIN
MAX
0.189
0.197
0.150
0.157
0.053
0.069
0.013
0.020
0.050 BSC
0.004
0.010
0.007
0.010
0.016
0.050
0 _
8 _
0.010
0.020
0.228
0.244
MC33275, NCV33275
PACKAGE DIMENSIONS
8 PIN DFN, 4x4
MN SUFFIX
CASE 488AF−01
ISSUE B
A
D
8X
B
8X
PIN ONE
IDENTIFICATION
K
8
E
5
0.15 C
2X
b
2X
0.15 C
0.10 C
8X
0.08 C
SEATING
PLANE
A1
8X NOTE 3
0.05 C
ÇÇÇ
L
Ç ÇÇ
Ç ÇÇ
Ç ÇÇ
1
D2
4
E2
0.10 C A B
TOP VIEW
NOTES:
1. DIMENSIONS AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.25 AND 0.30 MM FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
DIM
A
A1
A3
b
D
D2
E
E2
e
K
L
e
BOTTOM VIEW
A
(A3)
C
SIDE VIEW
SOLDERING FOOTPRINT*
4.30
2.21
8X
ÇÇ
ÇÇ
ÇÇ
ÇÇ
ÇÇ
ÇÇ
2.39
1
8X
0.35
ÇÇ
ÇÇ
ÇÇ
ÇÇ
ÇÇ
ÇÇ
DIMENSIONS: MILLIMETERS
0.63
0.40
0.80
PITCH
2.75
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
14
MILLIMETERS
MIN
MAX
0.80
1.00
0.00
0.05
0.20 REF
0.25
0.35
4.00 BSC
1.91
2.21
4.00 BSC
2.09
2.39
0.80 BSC
0.20
−−−
0.30
0.50
MC33275, NCV33275
PACKAGE DIMENSIONS
DPAK−3
DT SUFFIX
CASE 369A−13
ISSUE AB
−T−
C
B
V
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
SEATING
PLANE
E
R
4
Z
A
S
1
2
3
U
K
F
J
L
H
D
G
2 PL
0.13 (0.005)
M
DIM
A
B
C
D
E
F
G
H
J
K
L
R
S
U
V
Z
INCHES
MIN
MAX
0.235
0.250
0.250
0.265
0.086
0.094
0.027
0.035
0.033
0.040
0.037
0.047
0.180 BSC
0.034
0.040
0.018
0.023
0.102
0.114
0.090 BSC
0.175
0.215
0.020
0.050
0.020
−−−
0.030
0.050
0.138
−−−
MILLIMETERS
MIN
MAX
5.97
6.35
6.35
6.73
2.19
2.38
0.69
0.88
0.84
1.01
0.94
1.19
4.58 BSC
0.87
1.01
0.46
0.58
2.60
2.89
2.29 BSC
4.45
5.46
0.51
1.27
0.51
−−−
0.77
1.27
3.51
−−−
T
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Phone: 81−3−5773−3850
http://onsemi.com
15
For additional information, please contact your
local Sales Representative.
MC33275/D