FREESCALE MC68HC908LD64

MC68HC908LD64
Data Sheet
M68HC08
Microcontrollers
MC68HC908LD64
Rev. 3.0
07/2004
freescale.com
MC68HC908LD64
Data Sheet
To provide the most up-to-date information, the revision of our
documents on the World Wide Web will be the most current. Your printed
copy may be an earlier revision. To verify you have the latest information
available, refer to:
http://www.freescale.com
The following revision history table summarizes changes contained in
this document. For your convenience, the page number designators
have been linked to the appropriate location.
Freescale and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
This product incorporates SuperFlash® technology licensed from SST.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
© Freescale Semiconductor, Inc., 2004
Data Sheet
3
Revision History
Revision History
Date
July 2004
Data Sheet
4
Revision
Level
3
Page
Number(s)
Description
Figure 13-2 . ADC Block Diagram — Removed incorrect
ADICLK input to clock generator in block diagram.
179
18.7.1 OSD Control Register (OSDCR) — Corrected HALFCLK
bit definitions.
278
18.7.2 OSD Status Register (OSDSR) — Corrected WRDY bit
description.
278
18.7.3 OSD Data Registers (OSDDRH:OSDDRL) — Corrected
OSDD[15:0] bits description.
279
18.8.3.5 Frame Control Registers — Corrected OSD_EN bit
location.
288
Section 11. Timer Interface Module (TIM) — Corrected timer
discrepancies throughout.
149
Section 16. DDC12AB Interface — Changed the prefix "D" to
"DDC" in DDC12AB register name abbreviations throughout.
235
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet — MC68HC908LD64
List of Sections
Section 1. General Description . . . . . . . . . . . . . . . . . . . . 31
Section 2. Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Section 3. Random-Access Memory (RAM) . . . . . . . . . . 61
Section 4. FLASH Memory . . . . . . . . . . . . . . . . . . . . . . . . 63
Section 5. Configuration Register (CONFIG) . . . . . . . . . 75
Section 6. Central Processor Unit (CPU) . . . . . . . . . . . . 77
Section 7. Oscillator (OSC) . . . . . . . . . . . . . . . . . . . . . . . 95
Section 8. Clock Generator Module (CGM) . . . . . . . . . . . 99
Section 9. System Integration Module (SIM) . . . . . . . . 113
Section 10. Monitor ROM (MON) . . . . . . . . . . . . . . . . . . 137
Section 11. Timer Interface Module (TIM) . . . . . . . . . . . 149
Section 12. Pulse Width Modulator (PWM) . . . . . . . . . . 171
Section 13. Analog-to-Digital Converter (ADC) . . . . . . 177
Section 14. Universal Serial Bus Module (USB) . . . . . . 187
Section 15. Multi-Master IIC Interface (MMIIC) . . . . . . . 221
Section 16. DDC12AB Interface . . . . . . . . . . . . . . . . . . . 235
Section 17. Sync Processor . . . . . . . . . . . . . . . . . . . . . . 251
Section 18. On-Screen Display (OSD) . . . . . . . . . . . . . . 271
Section 19. Input/Output (I/O) Ports . . . . . . . . . . . . . . . 293
Section 20. External Interrupt (IRQ) . . . . . . . . . . . . . . . 315
Section 21. Keyboard Interrupt Module (KBI). . . . . . . . 321
Section 22. Computer Operating Properly (COP) . . . . 329
Section 23. Break Module (BRK) . . . . . . . . . . . . . . . . . . 335
Section 24. Electrical Specifications. . . . . . . . . . . . . . . 343
Section 25. Mechanical Specifications . . . . . . . . . . . . . 357
Section 26. Ordering Information . . . . . . . . . . . . . . . . . 359
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
List of Sections
5
List of Sections
Data Sheet
6
MC68HC908LD64 — Rev. 3.0
List of Sections
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Table of Contents
Section 1. General Description
1.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
1.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
1.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
1.4
MCU Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
1.5
Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
1.6
Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Section 2. Memory Map
2.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
2.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
2.3
Unimplemented Memory Locations . . . . . . . . . . . . . . . . . . . . . 41
2.4
Reserved Memory Locations . . . . . . . . . . . . . . . . . . . . . . . . . . 42
2.5
Input/Output (I/O) Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Section 3. Random-Access Memory (RAM)
3.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
3.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
3.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Section 4. FLASH Memory
4.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
4.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Table of Contents
7
Table of Contents
4.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
4.4
FLASH Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
4.4.1
OSD FLASH Even High Byte Write Buffer (OSDEHBUF) . . 67
4.5
FLASH Block Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . 68
4.6
FLASH Mass Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . 69
4.7
FLASH Program Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . .70
4.8
FLASH Block Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
4.8.1
FLASH Block Protect Registers . . . . . . . . . . . . . . . . . . . . . . 72
Section 5. Configuration Register (CONFIG)
5.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
5.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
5.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
5.4
Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Section 6. Central Processor Unit (CPU)
6.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
6.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
6.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
6.4
CPU Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
6.4.1
Accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
6.4.2
Index Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
6.4.3
Stack Pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
6.4.4
Program Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
6.4.5
Condition Code Register . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
6.5
Arithmetic/Logic Unit (ALU) . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
6.6
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
6.6.1
Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
6.6.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
6.7
CPU During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Data Sheet
8
MC68HC908LD64 — Rev. 3.0
Table of Contents
Freescale Semiconductor
Table of Contents
6.8
Instruction Set Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
6.9
Opcode Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Section 7. Oscillator (OSC)
7.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
7.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
7.3
Oscillator External Connections . . . . . . . . . . . . . . . . . . . . . . . .96
7.4
I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
7.4.1
Crystal Amplifier Input Pin (OSC1). . . . . . . . . . . . . . . . . . . . 97
7.4.2
Crystal Amplifier Output Pin (OSC2) . . . . . . . . . . . . . . . . . . 97
7.4.3
Oscillator Enable Signal (SIMOSCEN). . . . . . . . . . . . . . . . . 97
7.4.4
External Clock Source (OSCXCLK) . . . . . . . . . . . . . . . . . . . 97
7.4.5
Oscillator Out (OSCOUT). . . . . . . . . . . . . . . . . . . . . . . . . . . 97
7.5
Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
7.5.1
Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
7.5.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
7.6
Oscillator During Break Mode. . . . . . . . . . . . . . . . . . . . . . . . . . 98
Section 8. Clock Generator Module (CGM)
8.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
8.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
8.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
8.4
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
8.4.1
Crystal Oscillator Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . .103
8.5
CGM I/O Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
8.5.1
External Filter Capacitor Pin (CGMXFC) . . . . . . . . . . . . . . 103
8.5.2
PLL Analog Power Pin (VDDA) . . . . . . . . . . . . . . . . . . . . . 103
8.5.3
PLL Analog Ground Pin (VSSA). . . . . . . . . . . . . . . . . . . . . 103
8.5.4
Crystal Output Frequency Signal (OSCXCLK). . . . . . . . . . 104
8.5.5
Crystal Reference Frequency Signal (OSCRCLK). . . . . . . 104
8.5.6
CGM Base Clock Output (DCLK1) . . . . . . . . . . . . . . . . . . . 104
8.5.7
CGM CPU Interrupt (CGMINT) . . . . . . . . . . . . . . . . . . . . . 104
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Table of Contents
9
Table of Contents
8.6
CGM I/O Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
8.6.1
PLL Control Register (PCTL) . . . . . . . . . . . . . . . . . . . . . . . 105
8.6.2
PLL Bandwidth Control Register (PBWC) . . . . . . . . . . . . . 106
8.6.3
PLL Programming Register (PPG) . . . . . . . . . . . . . . . . . . . 108
8.6.4
H & V Sync Output Control Register (HVOCR) . . . . . . . . . 110
8.7
Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
8.8
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
8.8.1
Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
8.8.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
8.9
CGM During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . 112
Section 9. System Integration Module (SIM)
9.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
9.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
9.3
SIM Bus Clock Control and Generation . . . . . . . . . . . . . . . . . 117
9.3.1
Bus Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
9.3.2
Clock Start-Up from POR . . . . . . . . . . . . . . . . . . . . . . . . . . 117
9.3.3
Clocks in Stop Mode and Wait Mode . . . . . . . . . . . . . . . . . 117
9.4
Reset and System Initialization. . . . . . . . . . . . . . . . . . . . . . . . 118
9.4.1
External Pin Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
9.4.2
Active Resets from Internal Sources . . . . . . . . . . . . . . . . . 119
9.4.2.1
Power-On Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
9.4.2.2
Computer Operating Properly (COP) Reset. . . . . . . . . . 121
9.4.2.3
Low-Voltage Inhibit Reset . . . . . . . . . . . . . . . . . . . . . . .121
9.4.2.4
Illegal Opcode Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
9.4.2.5
Illegal Address Reset . . . . . . . . . . . . . . . . . . . . . . . . . . .122
9.5
SIM Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
9.5.1
SIM Counter During Power-On Reset . . . . . . . . . . . . . . . . 122
9.5.2
SIM Counter During Stop Mode Recovery . . . . . . . . . . . . . 122
9.5.3
SIM Counter and Reset States. . . . . . . . . . . . . . . . . . . . . . 123
9.6
Exception Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123
9.6.1
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
9.6.1.1
Hardware Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Data Sheet
10
MC68HC908LD64 — Rev. 3.0
Table of Contents
Freescale Semiconductor
Table of Contents
9.6.1.2
9.6.2
9.6.2.1
9.6.2.2
9.6.3
9.6.4
9.6.5
SWI Instruction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Interrupt Status Registers. . . . . . . . . . . . . . . . . . . . . . . . . . 127
Interrupt Status Register 1 . . . . . . . . . . . . . . . . . . . . . . . 129
Interrupt Status Register 2 . . . . . . . . . . . . . . . . . . . . . . . 129
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Status Flag Protection in Break Mode . . . . . . . . . . . . . . . . 130
9.7
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
9.7.1
Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131
9.7.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132
9.8
SIM Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
9.8.1
SIM Break Status Register (SBSR) . . . . . . . . . . . . . . . . . . 134
9.8.2
SIM Reset Status Register (SRSR) . . . . . . . . . . . . . . . . . . 135
9.8.3
SIM Break Flag Control Register (SBFCR) . . . . . . . . . . . . 136
Section 10. Monitor ROM (MON)
10.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
10.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
10.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
10.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138
10.4.1 Entering Monitor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
10.4.2 Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
10.4.3 Echoing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
10.4.4 Break Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
10.4.5 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
10.4.6 Baud Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147
Section 11. Timer Interface Module (TIM)
11.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .149
11.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
11.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
11.4
Pin Name Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Table of Contents
11
Table of Contents
11.5 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .151
11.5.1 TIM Counter Prescaler . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
11.5.2 Input Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
11.5.3 Output Compare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
11.5.3.1
Unbuffered Output Compare . . . . . . . . . . . . . . . . . . . . . 154
11.5.3.2
Buffered Output Compare . . . . . . . . . . . . . . . . . . . . . . .155
11.5.4 Pulse Width Modulation (PWM) . . . . . . . . . . . . . . . . . . . . . 155
11.5.4.1
Unbuffered PWM Signal Generation . . . . . . . . . . . . . . . 156
11.5.4.2
Buffered PWM Signal Generation . . . . . . . . . . . . . . . . . 157
11.5.4.3
PWM Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
11.6
Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159
11.7 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
11.7.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159
11.7.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160
11.8
TIM During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . 160
11.9
I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
11.10 I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
11.10.1 TIM Status and Control Register (TSC) . . . . . . . . . . . . . . . 161
11.10.2 TIM Counter Registers (TCNTH:TCNTL) . . . . . . . . . . . . . . 163
11.10.3 TIM Counter Modulo Registers (TMODH:TMODL) . . . . . . 164
11.10.4 TIM Channel Status and Control Registers (TSC0:TSC1) . 165
11.10.5 TIM Channel Registers (TCH0H/L:TCH1H/L) . . . . . . . . . . 168
Section 12. Pulse Width Modulator (PWM)
12.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171
12.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
12.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171
12.4 PWM Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
12.4.1 PWM Data Registers 0 to 7 (0PWM–7PWM). . . . . . . . . . . 173
12.4.2 PWM Control Register (PWMCR) . . . . . . . . . . . . . . . . . . . 174
Data Sheet
12
MC68HC908LD64 — Rev. 3.0
Table of Contents
Freescale Semiconductor
Table of Contents
Section 13. Analog-to-Digital Converter (ADC)
13.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .177
13.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
13.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
13.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .179
13.4.1 ADC Port I/O Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
13.4.2 Voltage Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180
13.4.3 Conversion Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
13.4.4 Continuous Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
13.4.5 Accuracy and Precision . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
13.5
Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181
13.6 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
13.6.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181
13.6.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .182
13.7 I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
13.7.1 ADC Analog Power Pin (VDDA). . . . . . . . . . . . . . . . . . . . . 182
13.7.2 ADC Analog Ground Pin (VSSA) . . . . . . . . . . . . . . . . . . . .182
13.7.3 ADC Voltage Reference High Pin (VRH) . . . . . . . . . . . . . . 182
13.7.4 ADC Voltage Reference Low Pin (VRL). . . . . . . . . . . . . . . 182
13.7.5 ADC Voltage In (ADCVIN) . . . . . . . . . . . . . . . . . . . . . . . . . 182
13.8 I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
13.8.1 ADC Status and Control Register. . . . . . . . . . . . . . . . . . . .183
13.8.2 ADC Data Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
13.8.3 ADC Input Clock Register . . . . . . . . . . . . . . . . . . . . . . . . . 185
Section 14. Universal Serial Bus Module (USB)
14.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .187
14.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
14.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
14.4
I/O Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
14.5
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Table of Contents
13
Table of Contents
14.6 Hub Function I/O Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 194
14.6.1 USB Hub Root Port Control Register (HRPCR) . . . . . . . . . 194
14.6.2 USB Hub Downstream Port Control Registers
(HDP1CR–HDP4CR) . . . . . . . . . . . . . . . . . . . . . . . . . . 195
14.6.3 USB SIE Timing Interrupt Register (SIETIR) . . . . . . . . . . . 198
14.6.4 USB SIE Timing Status Register (SIETSR) . . . . . . . . . . . . 200
14.6.5 USB Hub Address Register (HADDR) . . . . . . . . . . . . . . . . 202
14.6.6 USB Hub Interrupt Register 0 (HIR0) . . . . . . . . . . . . . . . . . 203
14.6.7 USB Hub Control Register 0 (HCR0) . . . . . . . . . . . . . . . . . 205
14.6.8 USB Hub Endpoint 1 Control and Data Register (HCDR) . 206
14.6.9 USB Hub Status Register (HSR) . . . . . . . . . . . . . . . . . . . . 208
14.6.10 USB Hub Endpoint 0 Data Registers (HE0D0–HE0D7). . . 209
14.7 Embedded Device Function I/O Registers . . . . . . . . . . . . . . . 209
14.7.1 USB Embedded Device Address Register (DADDR). . . . . 210
14.7.2 USB Embedded Device Interrupt Register 0 (DIR0) . . . . . 210
14.7.3 USB Embedded Device Interrupt Register 1 (DIR1) . . . . . 212
14.7.4 USB Embedded Device Control Register 0 (DCR0) . . . . . 213
14.7.5 USB Embedded Device Control Register 1 (DCR1) . . . . . 215
14.7.6 USB Embedded Device Control Register 2 (DCR2) . . . . . 216
14.7.7 USB Embedded Device Status Register (DSR) . . . . . . . . . 217
14.7.8 USB Embedded Device Endpoint 0 Data Registers
(DE0D0–DE0D7). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
14.7.9 USB Embedded Device Endpoint 1/2 Data Registers
(DE1D0–DE1D7). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
Section 15. Multi-Master IIC Interface (MMIIC)
15.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .221
15.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
15.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
15.4
I/O Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
15.5 Multi-Master IIC Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
15.5.1 Multi-Master IIC Address Register (MMADR) . . . . . . . . . . 224
15.5.2 Multi-Master IIC Control Register (MMCR) . . . . . . . . . . . . 225
15.5.3 Multi-Master IIC Master Control Register (MIMCR) . . . . . . 226
15.5.4 Multi-Master IIC Status Register (MMSR) . . . . . . . . . . . . . 228
Data Sheet
14
MC68HC908LD64 — Rev. 3.0
Table of Contents
Freescale Semiconductor
Table of Contents
15.5.5
15.5.6
15.6
Multi-Master IIC Data Transmit Register (MMDTR) . . . . . . 230
Multi-Master IIC Data Receive Register (MMDRR) . . . . . . 231
Programming Considerations . . . . . . . . . . . . . . . . . . . . . . . . . 232
Section 16. DDC12AB Interface
16.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .235
16.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235
16.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
16.4
I/O Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
16.5
DDC Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238
16.6 DDC Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238
16.6.1 DDC Address Register (DDCADR) . . . . . . . . . . . . . . . . . . 238
16.6.2 DDC2 Address Register (DDC2ADR) . . . . . . . . . . . . . . . . 239
16.6.3 DDC Control Register (DDCCR) . . . . . . . . . . . . . . . . . . . . 240
16.6.4 DDC Master Control Register (DDCMCR) . . . . . . . . . . . . . 241
16.6.5 DDC Status Register (DDCSR) . . . . . . . . . . . . . . . . . . . . . 244
16.6.6 DDC Data Transmit Register (DDCDTR) . . . . . . . . . . . . . . 246
16.6.7 DDC Data Receive Register (DDCDRR) . . . . . . . . . . . . . . 247
16.7
Programming Considerations . . . . . . . . . . . . . . . . . . . . . . . . . 248
Section 17. Sync Processor
17.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .251
17.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
17.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
17.4
I/O Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253
17.5 Functional Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
17.5.1 Polarity Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
17.5.1.1
Hsync Polarity Detection . . . . . . . . . . . . . . . . . . . . . . . . 256
17.5.1.2
Vsync Polarity Detection . . . . . . . . . . . . . . . . . . . . . . . . 256
17.5.1.3
Composite Sync Polarity Detection . . . . . . . . . . . . . . . . 256
17.5.2 Sync Signal Counters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Table of Contents
15
Table of Contents
17.5.3
17.5.4
17.5.5
Polarity Controlled HOUT and VOUT Outputs . . . . . . . . . . 257
Clamp Pulse Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258
Low Vertical Frequency Detect . . . . . . . . . . . . . . . . . . . . . 259
17.6 Sync Processor I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . 259
17.6.1 Sync Processor Control & Status Register (SPCSR). . . . . 259
17.6.2 Sync Processor Input/Output Control Register (SPIOCR) . 261
17.6.3 Vertical Frequency Registers (VFRs). . . . . . . . . . . . . . . . . 263
17.6.4 Hsync Frequency Registers (HFRs). . . . . . . . . . . . . . . . . . 265
17.6.5 Sync Processor Control Register 1 (SPCR1). . . . . . . . . . . 267
17.6.6 H & V Sync Output Control Register (HVOCR) . . . . . . . . . 268
17.7
System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .269
Section 18. On-Screen Display (OSD)
18.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .271
18.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
18.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
18.4
System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273
18.5
OSD FLASH Font Memory Map . . . . . . . . . . . . . . . . . . . . . . . 275
18.6
OSD Screen Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
18.7 OSD Module I/O Registers . . . . . . . . . . . . . . . . . . . . . . . . . . .277
18.7.1 OSD Control Register (OSDCR) . . . . . . . . . . . . . . . . . . . . 277
18.7.2 OSD Status Register (OSDSR) . . . . . . . . . . . . . . . . . . . . . 278
18.7.3 OSD Data Registers (OSDDRH:OSDDRL) . . . . . . . . . . . . 279
18.7.4 OSD Row Address Register (OSDRAR) . . . . . . . . . . . . . . 280
18.7.5 OSD Column Address Register (OSDCAR). . . . . . . . . . . . 280
18.7.6 OSD FLASH Even High Byte Write Buffer (OSDEHBUF) . 281
18.8 OSD Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
18.8.1 OSD Display Registers (Attribute and Code Registers) . . . 282
18.8.2 Row Attribute Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
18.8.3 Control, Window, and Pattern Registers . . . . . . . . . . . . . . 283
18.8.3.1
Window Registers 1, 2, 3, 4 . . . . . . . . . . . . . . . . . . . . . . 284
18.8.3.2
Vertical Delay Control Register . . . . . . . . . . . . . . . . . . . 285
18.8.3.3
Horizontal Delay Control Register . . . . . . . . . . . . . . . . . 286
Data Sheet
16
MC68HC908LD64 — Rev. 3.0
Table of Contents
Freescale Semiconductor
Table of Contents
18.8.3.4
18.8.3.5
Character Height Control Register . . . . . . . . . . . . . . . . . 286
Frame Control Registers . . . . . . . . . . . . . . . . . . . . . . . . 288
Section 19. Input/Output (I/O) Ports
19.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .293
19.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294
19.3 Port A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
19.3.1 Port A Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
19.3.2 Data Direction Register A . . . . . . . . . . . . . . . . . . . . . . . . . 298
19.3.3 Port A Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299
19.4 Port B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
19.4.1 Port B Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
19.4.2 Data Direction Register B . . . . . . . . . . . . . . . . . . . . . . . . . 301
19.4.3 Port B Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302
19.5 Port C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303
19.5.1 Port C Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303
19.5.2 Data Direction Register C . . . . . . . . . . . . . . . . . . . . . . . . . 304
19.5.3 Port C Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305
19.6 Port D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
19.6.1 Port D Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
19.6.2 Data Direction Register D. . . . . . . . . . . . . . . . . . . . . . . . . . 307
19.6.3 Port D Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
19.7 Port E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311
19.7.1 Port E Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311
19.7.2 Data Direction Register E. . . . . . . . . . . . . . . . . . . . . . . . . . 312
19.7.3 Port E Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
Section 20. External Interrupt (IRQ)
20.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .315
20.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315
20.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315
20.4
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .316
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Table of Contents
17
Table of Contents
20.4.1
IRQ Pin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318
20.5
IRQ Status and Control Register (INTSCR) . . . . . . . . . . . . . . 319
20.6
IRQ Module During Break Interrupts . . . . . . . . . . . . . . . . . . . 320
Section 21. Keyboard Interrupt Module (KBI)
21.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .321
21.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321
21.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
21.4
I/O Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
21.5
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .323
21.6
Keyboard Initialization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
21.7 I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
21.7.1 Keyboard Status and Control Register. . . . . . . . . . . . . . . . 326
21.7.2 Keyboard Interrupt Enable Register . . . . . . . . . . . . . . . . . . 327
21.8 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327
21.8.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .327
21.8.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .327
21.9
Keyboard Module During Break Interrupts . . . . . . . . . . . . . . . 328
Section 22. Computer Operating Properly (COP)
22.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .329
22.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
22.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .330
22.4 I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331
22.4.1 OSCXCLK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .331
22.4.2 STOP Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331
22.4.3 COPCTL Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .331
22.4.4 Power-On Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331
22.4.5 Internal Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332
22.4.6 Reset Vector Fetch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332
Data Sheet
18
MC68HC908LD64 — Rev. 3.0
Table of Contents
Freescale Semiconductor
Table of Contents
22.4.7
22.4.8
COPD (COP Disable). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332
COPRS (COP Rate Select) . . . . . . . . . . . . . . . . . . . . . . . . 332
22.5
COP Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
22.6
Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .333
22.7
Monitor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .333
22.8 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
22.8.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .334
22.8.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .334
22.9
COP Module During Break Mode . . . . . . . . . . . . . . . . . . . . . . 334
Section 23. Break Module (BRK)
23.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .335
23.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335
23.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336
23.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .336
23.4.1 Flag Protection During Break Interrupts . . . . . . . . . . . . . . . 338
23.4.2 CPU During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . .338
23.4.3 TIM During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . 338
23.4.4 COP During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . 338
23.5 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338
23.5.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .338
23.5.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .339
23.6 Break Module Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339
23.6.1 Break Status and Control Register. . . . . . . . . . . . . . . . . . . 339
23.6.2 Break Address Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 340
23.6.3 SIM Break Status Register . . . . . . . . . . . . . . . . . . . . . . . . . 340
23.6.4 SIM Break Flag Control Register . . . . . . . . . . . . . . . . . . . . 342
Section 24. Electrical Specifications
24.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .343
24.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Table of Contents
19
Table of Contents
24.3
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . 344
24.4
Functional Operating Range. . . . . . . . . . . . . . . . . . . . . . . . . . 345
24.5
Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345
24.6
DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 346
24.7
Control Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347
24.8
TImer Interface Module Characteristics . . . . . . . . . . . . . . . . . 347
24.9
Oscillator Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347
24.10 ADC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 348
24.11 Sync Processor Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349
24.12 USB DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . 349
24.12.1 USB Low Speed Source Electrical Characteristics . . . . . . 350
24.12.2 USB High Speed Source Electrical Characteristics . . . . . . 351
24.12.3 HUB Repeater Electrical Characteristics . . . . . . . . . . . . . . 352
24.12.4 USB Signaling Levels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353
24.13 DDC12AB/MMIIC Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354
24.13.1 DDC12AB/MMIIC Interface Input Signal Timing . . . . . . . . 354
24.13.2 DDC12AB/MMIIC Interface Output Signal Timing . . . . . . . 354
24.14 FLASH Memory Characteristics . . . . . . . . . . . . . . . . . . . . . . . 355
Section 25. Mechanical Specifications
25.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .357
25.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357
25.3
64-Pin Plastic Quad Flat Pack (QFP) . . . . . . . . . . . . . . . . . . . 358
Section 26. Ordering Information
26.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .359
26.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359
26.3
MC Order Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359
Data Sheet
20
MC68HC908LD64 — Rev. 3.0
Table of Contents
Freescale Semiconductor
Data Sheet — MC68HC908LD64
List of Figures
Figure
Title
1-1
1-2
MC68HC908LD64 MCU Block Diagram. . . . . . . . . . . . . . . . . . 35
64-Pin QFP Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
2-1
2-2
Memory Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Control, Status, and Data Registers . . . . . . . . . . . . . . . . . . . . .45
4-1
4-2
4-3
4-4
4-5
4-6
4-7
4-8
FLASH I/O Register Summary . . . . . . . . . . . . . . . . . . . . . . . . . 64
47,616-byte FLASH Control Register (FLCR) . . . . . . . . . . . . . 66
13K-byte FLASH Control Register (FLCR1) . . . . . . . . . . . . . . . 66
OSD FLASH Even High Byte Write Buffer (OSDEHBUF) . . . . 67
FLASH Programming Flowchart . . . . . . . . . . . . . . . . . . . . . . . . 71
47,616-byte FLASH Block Protect Register (FLBPR). . . . . . . . 72
13K-byte FLASH Block Protect Register 1 (FLBPR1) . . . . . . . 72
FLASH Block Protect Start Address . . . . . . . . . . . . . . . . . . . . .73
5-1
Configuration Register (CONFIG). . . . . . . . . . . . . . . . . . . . . . . 76
6-1
6-2
6-3
6-4
6-5
6-6
CPU Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Accumulator (A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Index Register (H:X) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Stack Pointer (SP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Program Counter (PC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Condition Code Register (CCR) . . . . . . . . . . . . . . . . . . . . . . . . 82
7-1
Oscillator External Connections . . . . . . . . . . . . . . . . . . . . . . . .96
8-1
8-2
8-3
8-4
CGM Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
CGM I/O Register Summary. . . . . . . . . . . . . . . . . . . . . . . . . . 102
PLL Control Register (PCTL) . . . . . . . . . . . . . . . . . . . . . . . . . 105
PLL Bandwidth Control Register (PBWC) . . . . . . . . . . . . . . . 107
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Page
Data Sheet
List of Figures
21
List of Figures
Figure
Title
8-5
8-6
PLL Programming Register (PPG) . . . . . . . . . . . . . . . . . . . . . 108
H&V Sync Output Control Register (HVOCR) . . . . . . . . . . . . 110
9-1
9-2
9-3
9-4
9-5
9-6
9-7
9-8
9-9
9-10
9-11
9-12
9-13
9-14
9-15
9-16
9-17
9-18
9-19
9-20
9-21
SIM Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
SIM I/O Register Summary. . . . . . . . . . . . . . . . . . . . . . . . . . .116
OSC Clock Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
External Reset Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
Internal Reset Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Sources of Internal Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
POR Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Interrupt Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Interrupt Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Interrupt Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Interrupt Recognition Example . . . . . . . . . . . . . . . . . . . . . . . . 126
Interrupt Status Register 1 (INT1). . . . . . . . . . . . . . . . . . . . . . 129
Interrupt Status Register 2 (INT2). . . . . . . . . . . . . . . . . . . . . . 129
Wait Mode Entry Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Wait Recovery from Interrupt or Break . . . . . . . . . . . . . . . . . . 132
Wait Recovery from Internal Reset. . . . . . . . . . . . . . . . . . . . . 132
Stop Mode Entry Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Stop Mode Recovery from Interrupt or Break . . . . . . . . . . . . . 133
SIM Break Status Register (SBSR) . . . . . . . . . . . . . . . . . . . . 134
SIM Reset Status Register (SRSR) . . . . . . . . . . . . . . . . . . . . 135
SIM Break Flag Control Register (SBFCR) . . . . . . . . . . . . . . 136
10-1
10-2
10-3
10-4
10-5
Monitor Mode Circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Monitor Data Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Sample Monitor Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Read Transaction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .143
Break Transaction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144
11-1
11-2
11-3
11-4
11-5
TIM Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
PWM Period and Pulse Width . . . . . . . . . . . . . . . . . . . . . . . . 156
TIM Status and Control Register (TSC) . . . . . . . . . . . . . . . . . 161
TIM Counter Registers (TCNTH:TCNTL) . . . . . . . . . . . . . . . . 163
TIM Counter Modulo Registers (TMODH:TMODL). . . . . . . . . 164
Data Sheet
22
Page
MC68HC908LD64 — Rev. 3.0
List of Figures
Freescale Semiconductor
List of Figures
Figure
Title
Page
11-6 TIM Channel Status and Control Registers (TSC0:TSC1) . . . 165
11-7 CHxMAX Latency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .168
11-8 TIM Channel Registers (TCH0H/L:TCH1H/L). . . . . . . . . . . . . 169
12-1
12-2
12-3
12-4
PWM I/O Register Summary . . . . . . . . . . . . . . . . . . . . . . . . . 172
PWM Data Registers 0 to 7 (0PWM–7PWM) . . . . . . . . . . . . . 173
PWM Control Register (PWMCR). . . . . . . . . . . . . . . . . . . . . . 174
8-Bit PWM Output Waveforms . . . . . . . . . . . . . . . . . . . . . . . . 175
13-1
13-2
13-3
13-4
13-5
ADC I/O Register Summary . . . . . . . . . . . . . . . . . . . . . . . . . . 178
ADC Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
ADC Status and Control Register (ADSCR) . . . . . . . . . . . . . . 183
ADC Data Register (ADR) . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
ADC Input Clock Register (ADICLK) . . . . . . . . . . . . . . . . . . . 185
14-1
14-2
14-3
14-4
USB I/O Register Summary . . . . . . . . . . . . . . . . . . . . . . . . . . 190
USB Module Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 193
USB Hub Root Port Control Register (HRPCR) . . . . . . . . . . . 194
USB Hub Downstream Port Control Registers
(HDP1CR–HDP4CR). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
USB SIE Timing Interrupt Register (SIETIR) . . . . . . . . . . . . . 198
USB SIE Timing Status Register (SIETSR) . . . . . . . . . . . . . . 200
USB Hub Address Register (HADDR) . . . . . . . . . . . . . . . . . . 202
USB Hub Interrupt Register 0 (HIR0) . . . . . . . . . . . . . . . . . . . 203
USB Hub Control Register 0 (HCR0) . . . . . . . . . . . . . . . . . . . 205
USB Hub Endpoint 1 Control and Data Register (HCDR) . . . 206
USB Hub Status Register (HSR) . . . . . . . . . . . . . . . . . . . . . . 208
USB Hub Endpoint 0 Data Registers (HE0D0–HE0D7) . . . . . 209
USB Embedded Device Address Register (DADDR) . . . . . . . 210
USB Embedded Device Interrupt Register 0 (DIR0). . . . . . . . 210
USB Embedded Device Interrupt Register 1 (DIR1). . . . . . . . 212
USB Embedded Device Control Register 0 (DCR0). . . . . . . . 213
USB Embedded Device Control Register 1 (DCR1). . . . . . . . 215
USB Embedded Device Control Register 2 (DCR2). . . . . . . . 216
USB Embedded Device Status Register (DSR) . . . . . . . . . . . 217
USB Embedded Device Endpoint 0 Data Registers
(DE0D0–DE0D7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
14-5
14-6
14-7
14-8
14-9
14-10
14-11
14-12
14-13
14-14
14-15
14-16
14-17
14-18
14-19
14-20
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
List of Figures
23
List of Figures
Figure
Title
Page
14-21 USB Embedded Device Endpoint 1/2 Data Registers
(DE1D0–DE1D7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
15-1
15-2
15-3
15-4
15-5
15-6
15-7
15-8
MMIIC I/O Register Summary. . . . . . . . . . . . . . . . . . . . . . . . . 223
Multi-Master IIC Address Register (MMADR). . . . . . . . . . . . . 224
Multi-Master IIC Control Register (MMCR). . . . . . . . . . . . . . . 225
Multi-Master IIC Master Control Register (MIMCR) . . . . . . . . 226
Multi-Master IIC Status Register (MMSR) . . . . . . . . . . . . . . . 228
Multi-Master IIC Data Transmit Register (MMDTR) . . . . . . . . 230
Multi-Master IIC Data Receive Register (MMDRR) . . . . . . . . 231
Data Transfer Sequences for Master/Slave
Transmit/Receive Modes . . . . . . . . . . . . . . . . . . . . . . . . . . 233
16-1
16-2
16-3
16-4
16-5
16-6
16-7
16-8
16-9
DDC I/O Register Summary . . . . . . . . . . . . . . . . . . . . . . . . . . 237
DDC Address Register (DDCADR). . . . . . . . . . . . . . . . . . . . . 238
DDC2 Address Register (DDC2ADR). . . . . . . . . . . . . . . . . . . 239
DDC Control Register (DDCCR). . . . . . . . . . . . . . . . . . . . . . . 240
DDC Master Control Register (DDCMCR) . . . . . . . . . . . . . . . 241
DDC Status Register (DDCSR) . . . . . . . . . . . . . . . . . . . . . . .244
DDC Data Transmit Register (DDCDTR) . . . . . . . . . . . . . . . . 246
DDC Data Receive Register (DDCDRR) . . . . . . . . . . . . . . . . 247
Data Transfer Sequences for Master/Slave
Transmit/Receive Modes . . . . . . . . . . . . . . . . . . . . . . . . . . 249
17-1
17-2
17-3
17-4
17-5
17-6
17-7
17-8
17-9
17-10
17-11
Sync Processor I/O Register Summary . . . . . . . . . . . . . . . . . 254
Sync Processor Block Diagram . . . . . . . . . . . . . . . . . . . . . . .255
Clamp Pulse Output Timing . . . . . . . . . . . . . . . . . . . . . . . . . . 258
Sync Processor Control & Status Register (SPCSR) . . . . . . . 259
Sync Processor Input/Output Control Register (SPIOCR) . . . 261
Vertical Frequency High Register . . . . . . . . . . . . . . . . . . . . . . 263
Vertical Frequency Low Register . . . . . . . . . . . . . . . . . . . . . . 263
Hsync Frequency High Register . . . . . . . . . . . . . . . . . . . . . . . 265
Hsync Frequency Low Register . . . . . . . . . . . . . . . . . . . . . . .265
Sync Processor Control Register 1 (SPCR1) . . . . . . . . . . . . . 267
H&V Sync Output Control Register (HVOCR) . . . . . . . . . . . . 268
Data Sheet
24
MC68HC908LD64 — Rev. 3.0
List of Figures
Freescale Semiconductor
List of Figures
Figure
Title
18-1
18-2
18-3
18-4
18-5
18-6
18-7
18-8
18-9
18-10
18-11
18-12
18-13
18-14
On-Screen Display I/O Register Summary . . . . . . . . . . . . . . . 273
OSD Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
Memory Map of OSD FLASH Fonts . . . . . . . . . . . . . . . . . . . .275
Memory Map of OSD Registers . . . . . . . . . . . . . . . . . . . . . . .276
OSD Control Register (OSDCR). . . . . . . . . . . . . . . . . . . . . . . 277
OSD Status Register (OSDSR) . . . . . . . . . . . . . . . . . . . . . . .278
OSD Data Register High (OSDDRH) . . . . . . . . . . . . . . . . . . . 279
OSD Data Register Low (OSDDRL) . . . . . . . . . . . . . . . . . . . .279
OSD Row Address Register (OSDRAR) . . . . . . . . . . . . . . . . 280
OSD Column Address Register (OSDCAR) . . . . . . . . . . . . . . 280
OSD FLASH Even High Byte Write Buffer (OSDEHBUF) . . . 281
OSD Font Even Byte Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . 281
Character Font Matrix Height Expansion by CH[3:0] . . . . . . . 287
Display Character Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
19-1
19-2
19-3
19-4
19-5
19-6
19-7
19-8
19-9
19-10
19-11
19-12
19-13
19-14
19-15
19-16
19-17
19-18
19-19
19-20
Port I/O Register Summary. . . . . . . . . . . . . . . . . . . . . . . . . . .294
Port A Data Register (PTA) . . . . . . . . . . . . . . . . . . . . . . . . . . 297
Data Direction Register A (DDRA) . . . . . . . . . . . . . . . . . . . . . 298
Port A I/O Circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298
Keyboard Interrupt Enable Register (KIER) . . . . . . . . . . . . . . 299
Port B Data Register (PTB) . . . . . . . . . . . . . . . . . . . . . . . . . . 300
Data Direction Register B (DDRB) . . . . . . . . . . . . . . . . . . . . . 301
Port B I/O Circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301
PWM Control Register (PWMCR). . . . . . . . . . . . . . . . . . . . . . 302
Port C Data Register (PTC) . . . . . . . . . . . . . . . . . . . . . . . . . . 303
Data Direction Register C (DDRC) . . . . . . . . . . . . . . . . . . . . . 304
Port C I/O Circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305
Port D Data Register (PTD) . . . . . . . . . . . . . . . . . . . . . . . . . . 306
Data Direction Register D (DDRD) . . . . . . . . . . . . . . . . . . . . . 307
Port D I/O Circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308
Port D Control Register (PDCR) . . . . . . . . . . . . . . . . . . . . . . . 309
Port E Data Register (PTE) . . . . . . . . . . . . . . . . . . . . . . . . . . 311
Data Direction Register E (DDRE) . . . . . . . . . . . . . . . . . . . . . 312
Port E I/O Circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312
Port E Control Register (PECR) . . . . . . . . . . . . . . . . . . . . . . . 313
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Page
Data Sheet
List of Figures
25
List of Figures
Figure
Title
Page
20-1 IRQ Module Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 317
20-2 IRQ I/O Register Summary. . . . . . . . . . . . . . . . . . . . . . . . . . .317
20-3 IRQ Status and Control Register (INTSCR) . . . . . . . . . . . . . . 319
21-1
21-2
21-3
21-4
KBI I/O Register Summary . . . . . . . . . . . . . . . . . . . . . . . . . . .322
Keyboard Interrupt Module Block Diagram. . . . . . . . . . . . . . . 323
Keyboard Status and Control Register (KBSCR) . . . . . . . . . . 326
Keyboard Interrupt Enable Register (KBIER) . . . . . . . . . . . . . 327
22-1 COP Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330
22-2 Configuration Register (CONFIG). . . . . . . . . . . . . . . . . . . . . . 332
22-3 COP Control Register (COPCTL) . . . . . . . . . . . . . . . . . . . . . . 333
23-1
23-2
23-3
23-4
23-5
23-6
23-7
Break Module Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . 337
Break Module I/O Register Summary . . . . . . . . . . . . . . . . . . . 337
Break Status and Control Register (BRKSCR). . . . . . . . . . . . 339
Break Address Register High (BRKH) . . . . . . . . . . . . . . . . . . 340
Break Address Register Low (BRKL) . . . . . . . . . . . . . . . . . . . 340
SIM Break Status Register (SBSR) . . . . . . . . . . . . . . . . . . . . 341
SIM Break Flag Control Register (SBFCR) . . . . . . . . . . . . . . 342
24-1 MMIIC Signal Timings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354
25-1 64-Pin QFP (Case #840B) . . . . . . . . . . . . . . . . . . . . . . . . . . . 358
Data Sheet
26
MC68HC908LD64 — Rev. 3.0
List of Figures
Freescale Semiconductor
Data Sheet — MC68HC908LD64
List of Tables
Table
Title
Page
1-1
Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
2-1
Vector Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
4-1
FLASH Memory Array Summary . . . . . . . . . . . . . . . . . . . . . . . 65
6-1
6-2
Instruction Set Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Opcode Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
8-1
8-2
Free-Running HSOUT, VSOUT, DE, and DCLK Settings . . . 102
VCO Frequency Multiplier (N) Selection. . . . . . . . . . . . . . . . . 109
9-1
9-2
9-3
9-4
Signal Name Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
PIN Bit Set Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Interrupt Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
SIM Registers Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
10-1
10-2
10-3
10-4
10-5
10-6
10-7
10-8
10-9
Monitor Mode Signal Requirements and Options . . . . . . . . . . 141
Mode Differences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
READ (Read Memory) Command . . . . . . . . . . . . . . . . . . . . . 144
WRITE (Write Memory) Command. . . . . . . . . . . . . . . . . . . . . 145
IREAD (Indexed Read) Command . . . . . . . . . . . . . . . . . . . . . 145
IWRITE (Indexed Write) Command . . . . . . . . . . . . . . . . . . . . 146
READSP (Read Stack Pointer) Command . . . . . . . . . . . . . . . 146
RUN (Run User Program) Command . . . . . . . . . . . . . . . . . . . 147
Monitor Baud Rate Selection . . . . . . . . . . . . . . . . . . . . . . . . . 147
11-1 Pin Name Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
11-2 Prescaler Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
11-3 Mode, Edge, and Level Selection . . . . . . . . . . . . . . . . . . . . . . 167
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
List of Tables
27
List of Tables
Table
Title
Page
12-1 PWM Channels and Port I/O pins. . . . . . . . . . . . . . . . . . . . . . 174
13-1 MUX Channel Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
13-2 ADC Clock Divide Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
14-1 USB I/O Pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
15-1 Pin Name Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
15-2 Baud Rate Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
16-1 Pin Name Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
16-2 Baud Rate Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
17-1
17-2
17-3
17-4
17-5
17-6
17-7
17-8
17-9
Pin Name Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253
Sync Output Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
Sync Output Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258
ATPOL, VINVO, and HINVO setting. . . . . . . . . . . . . . . . . . . .261
Sample Vertical Frame Frequencies . . . . . . . . . . . . . . . . . . . 264
Clamp Pulse Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
HSYNC Polarity Detection Pulse Width . . . . . . . . . . . . . . . . . 267
ATPOL, VINVO, and HINVO setting. . . . . . . . . . . . . . . . . . . .268
Free-Running HSOUT, VSOUT, DE, and DCLK Settings . . . 269
18-1 Shadow Width Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .289
18-2 Shadow Width Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .290
19-1
19-2
19-3
19-4
19-5
19-6
Port Control Register Bits Summary. . . . . . . . . . . . . . . . . . . .296
Port A Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299
Port B Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302
Port C Pin Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305
Port D Pin Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308
Port E Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
21-1 Pin Name Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
24-1 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . 344
Data Sheet
28
MC68HC908LD64 — Rev. 3.0
List of Tables
Freescale Semiconductor
List of Tables
Table
24-2
24-3
24-4
24-5
24-6
24-7
24-8
24-9
24-10
24-11
24-12
24-13
24-14
24-15
24-16
24-17
Title
Page
Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345
Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345
DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 346
Control Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347
TIM Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347
Oscillator Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347
ADC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 348
Sync Processor Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349
USB DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . 349
USB Low Speed Source Electrical Characteristics. . . . . . . . . 350
USB High Speed Source Electrical Characteristics . . . . . . . . 351
HUB Repeater Electrical Characteristics . . . . . . . . . . . . . . . . 352
USB Signaling Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353
DDC12AB/MMIIC Interface Input Signal Timing. . . . . . . . . . . 354
DDC12AB/MMIIC Interface Output Signal Timing . . . . . . . . . 354
FLASH Memory Electrical Characteristics . . . . . . . . . . . . . . . 355
26-1 MC Order Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
List of Tables
29
List of Tables
Data Sheet
30
MC68HC908LD64 — Rev. 3.0
List of Tables
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 1. General Description
1.1 Contents
1.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
1.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
1.4
MCU Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
1.5
Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
1.6
Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
1.2 Introduction
The MC68HC908LD64 is a member of the low-cost, high-performance
M68HC08 Family of 8-bit microcontroller units (MCUs). The M68HC08
Family is based on the customer-specified integrated circuit (CSIC)
design strategy. All MCUs in the family use the enhanced M68HC08
central processor unit (CPU08) and are available with a variety of
modules, memory sizes and types, and package types.
With special modules such as the sync processor, on-screen display
module, analog-to-digital converter, pulse modulator module, DDC12AB
interface, multi-master IIC interface, and universal serial bus interface,
the MC68HC908LD64 is designed specifically for use in digital monitor
systems.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
General Description
31
General Description
1.3 Features
Features of the MC68HC908LD64 MCU include the following:
•
High-performance M68HC08 architecture
•
Fully upward-compatible object code with M6805, M146805, and
M68HC05 families
•
Low-power design; fully static with stop and wait modes
•
3.3V operating voltage
•
6MHz internal bus frequency; with 24MHz external crystal
•
60,928 bytes of on-chip FLASH memory with security1 feature
•
2,048 bytes of on-chip random access memory (RAM)
•
39 general-purpose input/output (I/O) pins, including:
– 38 shared-function I/O pins
– 8-bit keyboard interrupt port
•
2-channel, 16-bit timer interface module (TIM) with selectable
input capture, output compare, and PWM capability on one
channel
•
6-channel, 8-bit analog-to-digital converter (ADC)
•
8-channel, 8-bit pulse width modulator (PWM)
•
Sync signal processor with the following features:
– Horizontal and vertical frequency counters
– Low vertical frequency indicator (40.7Hz)
– Polarity controlled Hsync and Vsync outputs from separate
sync or composite sync inputs
– Internal generated free-running Hsync, Vsync, DE, and DCLK
– CLAMP pulse output to the external pre-amp chip
•
On screen display (OSD) and full screen pattern display
1. No security feature is absolutely secure. However, Freescale’s strategy is to make reading or
copying the FLASH difficult for unauthorized users.
Data Sheet
32
MC68HC908LD64 — Rev. 3.0
General Description
Freescale Semiconductor
General Description
Features
•
Full Universal Serial Bus (USB) specification 1.1, composite hub
with embedded functions, including:
– One 12MHz upstream port
– Four 12MHz/1.5MHz downstream ports
– One hub control endpoint with 8-byte transmit buffer and
8-byte receive buffer
– One hub interrupt endpoint with 1-byte transmit buffer
– One device control endpoint with 8-byte transmit buffer and
8-byte receive buffer
– Two device interrupt endpoints with shared 8-byte transmit
buffer
•
DDC12AB1 module with the following:
– DDC1 hardware
– Multi-master IIC2 hardware for DDC2AB; with dual address
•
Additional multi-master IIC module
•
In-system programming capability using USB or DDC12AB
communication, or standard serial link on PTA0 pin
•
System protection features:
– Optional computer operating properly (COP) reset
– Illegal opcode detection with reset
– Illegal address detection with reset
•
Master reset pin (with internal pull-up) and power-on reset
•
IRQ interrupt pin with internal pull-up and schmitt-trigger input
•
64-pin quad flat pack (QFP) package
1. DDC is a VESA bus standard.
2. IIC is a proprietary Philips interface bus.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
General Description
33
General Description
Features of the CPU08 include the following:
•
Enhanced HC05 programming model
•
Extensive loop control functions
•
16 addressing modes (eight more than the HC05)
•
16-bit index register and stack pointer
•
Memory-to-memory data transfers
•
Fast 8 × 8 multiply instruction
•
Fast 16/8 divide instruction
•
Binary-coded decimal (BCD) instructions
•
Optimization for controller applications
•
Third party C language support
1.4 MCU Block Diagram
Figure 1-1 shows the structure of the MC68HC908LD64.
Data Sheet
34
MC68HC908LD64 — Rev. 3.0
General Description
Freescale Semiconductor
General Description
MCU Block Diagram
INTERNAL BUS
OSC1
OSC2
DDRA
MONITOR
MODULE
PTC6
PTC5/ADC5
:
PTC0/ADC0
8-BIT ANALOG-TO-DIGITAL
CONVERTER MODULE
USER FLASH VECTOR SPACE — 32 BYTES
CLOCK GENERATOR MODULE
PORTA
MONITOR ROM — 1,024+464 BYTES
PTB7/PWM7
:
PTB0/PWM0
PULSE WIDTH MODULATOR
MODULE
USER FLASH — 60,928 BYTES
USER RAM — 2,048 BYTES
PTA7/KBI7
:
PTA0/KBI0
DDRB
CONTROL AND STATUS REGISTERS — 80 BYTES
KEYBOARD INTERRUPT
MODULE
PORTB
ARITHMETIC/LOGIC
UNIT (ALU)
FREE-RUN PANEL TIMING
MODULE
DDRC
CPU
REGISTERS
PORTC
M68HC08 CPU
24-MHz OSCILLATOR
SYNC PROCESSOR
MODULE
CGMXFC
HSYNC††
VSYNC††
PHASE-LOCKED LOOP
CLAMP/TCH0
IRQ
EXTERNAL IRQ
MODULE
MULTI-MASTER IIC
INTERFACE MODULE
COMPUTER OPERATING
PROPERLY MODULE
DDC12AB INTERFACE
MODULE
PHSYNC††
PVSYNC††
PCLK††
OSDR
OSDG
OSDB
FBKG
ON-SCREEN DISPLAY
DS PORT 4
UNIVERSAL SERIAL BUS
INTERFACE MODULE
AND
HUB CONTROLLER
POWER
VRH
VRL
ADC REFERENCE
PTE7/DMINUS4
PTE6/DPLUS4
PTE5/DMINUS3
PTE4/DPLUS3
PTE3/DMINUS2
PTE2/DPLUS2
PTE1/DMINUS1
PTE0/DPLUS1
SECURITY
MODULE
MODULE
VDD1
VSS1
VDD2
VSS2
VDDA
VSSA
PTD7/IICSDA†
PTD6/IICSCL†
PTD5/DDCSDA†
PTD4/DDCSCL†
PTD3/HOUT
PTD2/VOUT
PTD1/DE
PTD0/DCLK
MONITOR MODE ENTRY
MODULE
DS PORT 3
DS PORT 2
DDRE
POWER-ON RESET
MODULE
PORTD
SYSTEM INTEGRATION
MODULE
PORTE
RST
DDRD
2-CHANNEL TIMER INTERFACE
MODULE
DS PORT 1
US PORT
DMINUS0
DPLUS0
† Pin is +5V open-drain
†† Pin is +5V input
Figure 1-1. MC68HC908LD64 MCU Block Diagram
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
General Description
35
General Description
VRL
PTC0/ADC0
PTC1/ADC1
PTC2/ADC2
PTC3/ADC3
PTC4/ADC4
VSS2
PTC5/ADC5
PTC6
PTA7/KBI7
PTA6/KBI6
PTA5/KBI5
61
60
59
58
57
56
55
54
53
52
51
50
1
PTA4/KBI4
VRH
62
VDDA
49
RST
63
64
IRQ
1.5 Pin Assignments
48
PTA3/KBI3
OSC1
2
47
PTA2/KBI2
OSC2
3
46
PTA1/KBI1
VSSA
4
45
PTA0/KBI0
VDD1
5
44
VDD2
DPLUS0
6
43
PTB7/PWM7
DMINUS0
7
42
PTB6/PWM6
PTE0/DPLUS1
8
41
PTB5/PWM5
PTE1/DMINUS1
9
40
PTB4/PWM4
PTE2/DPLUS2
10
39
PTB3/PWM3
PTE3/DMINUS2
11
38
PTB2/PWM2
PTE4/DPLUS3
12
37
PTB1/PWM1
PTE5/DMINUS3
13
36
PTB0/PWM0
PTE6/DPLUS4
14
35
PTD7IICSDA
PTE7/DMINUS4
15
34
PTD6/IICSCL
20
21
22
23
24
25
26
27
28
29
30
31
HSYNC
PVSYNC
PHSYNC
PCLK
OSDR
OSDG
OSDB
FBKG
PTD0/DCLK
PTD1/DE
PTD2/VOUT
PTD3/HOUT
PTD5/DDCSDA
PTD4/DDCSCL 32
19
33
VSYNC
CLAMP/TCH0
VSS1 17
18
CGMXFC 16
Figure 1-2. 64-Pin QFP Pin Assignment
Data Sheet
36
MC68HC908LD64 — Rev. 3.0
General Description
Freescale Semiconductor
General Description
Pin Functions
1.6 Pin Functions
Description of the pin functions are provided in Table 1-1.
Table 1-1. Pin Functions
PIN NAME
PIN DESCRIPTION
VDD1, VDD2
Power supply input to the MCU.
VSS1, VSS2
Power supply ground.
VDDA
Power supply input for analog circuits.
VSSA
Power supply ground for analog circuits.
OSC1, OSC2
Crystal connections to the on-chip oscillator.
An external clock can be connected directly to
OSC1; with OSC2 floating.
See Section 7. Oscillator (OSC).
RST
External reset pin; active low; with internal pull-up
and schmitt trigger input. It is driven low when any
internal reset source is asserted.
See Section 9. System Integration Module
(SIM).
IRQ
External IRQ pin; with schmitt trigger input and
internal pull-up. This pin is also used for mode
entry selection.
See Section 20. External Interrupt (IRQ) and
Section 9. System Integration Module (SIM).
CGMXFC
External filter capacitor connection for the CGM
module.
See Section 8. Clock Generator Module (CGM).
VSYNC
Vsync input to the sync processor.
This pin is rated at +5V.
See Section 17. Sync Processor.
HSYNC
Hsync input to the sync processor.
This pin is rated at +5V.
See Section 17. Sync Processor.
PTA7/KBI7–PTA0/KBI0
These are shared function, bidirectional I/O port
pins. Each pin contains a pull-up device to VDD
when it is configured as an external keyboard
interrupt pin.
See Section 19. Input/Output (I/O) Ports and
Section 21. Keyboard Interrupt Module (KBI).
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
General Description
37
General Description
Table 1-1. Pin Functions (Continued)
PIN NAME
PIN DESCRIPTION
PTB7/PWM7–PTB0/PWM0
These are shared-function, bidirectional I/O port
pins. Each pin can be configured as a standard I/O
pin or a PWM output channel.
See Section 19. Input/Output (I/O) Ports and
Section 12. Pulse Width Modulator (PWM).
VRH
High voltage reference input to ADC module.
VRL
Low voltage reference input to ADC module.
PTC6
This pin is a standard bidirectional I/O pin.
See Section 19. Input/Output (I/O) Ports.
PTC5/ADC5–PTC0/ADC0
These are shared-function, bidirectional I/O port
pins. Each pin can be configured as a standard I/O
pin or an ADC input channel.
See Section 19. Input/Output (I/O) Ports and
Section 13. Analog-to-Digital Converter (ADC).
PTD7/IICSDA
This is a shared-function pin. It can be configured
as a standard I/O pin or the data line of the multimaster IIC module. This pin is +5V open-drain
when configured as output.
See Section 19. Input/Output (I/O) Ports and
Section 15. Multi-Master IIC Interface (MMIIC).
PTD6/IICSCL
This is a shared function pin. It can be configured
as a standard I/O pin or the clock line of the multimaster IIC module. This pin is +5V open-drain
when configured as output.
See Section 19. Input/Output (I/O) Ports and
Section 15. Multi-Master IIC Interface (MMIIC).
PTD5/DDCSDA
This is a shared function pin. It can be configured
as a standard I/O pin or the data line of the
DDC12AB module. This pin is +5V open-drain
when configured as output.
See Section 19. Input/Output (I/O) Ports and
Section 16. DDC12AB Interface.
PTD4/DDCSCL
This is a shared function pin. It can be configured
as a standard I/O pin or the clock line of the
DDC12AB module. This pin is +5V open-drain
when configured as output.
See Section 19. Input/Output (I/O) Ports and
Section 16. DDC12AB Interface.
Data Sheet
38
MC68HC908LD64 — Rev. 3.0
General Description
Freescale Semiconductor
General Description
Pin Functions
Table 1-1. Pin Functions (Continued)
PIN NAME
PTD3/HOUT
PTD2/VOUT
PTD1/DE
PTD0/DCLK
These are shared function, bidirectional I/O port
pins. These pins can be configured as standard
I/O pins or free-run timing output signals.
See Section 19. Input/Output (I/O) Ports and
Section 17. Sync Processor.
CLAMP/TCH0
This is shared function pins. This TIM channel 0
I/O pin can be configured as the Sync processor
CLAMP output pin.
See Section 11. Timer Interface Module (TIM)
and Section 17. Sync Processor.
PVSYNC
Vsync input to the On-Screen Display module.
This pin is rated at +5V.
See Section 18. On-Screen Display (OSD).
PHSYNC
Hsync input to the On-Screen Display module.
This pin is rated at +5V.
See Section 18. On-Screen Display (OSD).
PCLK
Pixel clock input to the On-Screen Display module.
This pin is rated at +5V.
See Section 18. On-Screen Display (OSD).
OSDR
OSDG
OSDB
R, G, and B output of the On-Screen Display
module.
See Section 18. On-Screen Display (OSD).
FBKG
Pixel-enable output of the On-Screen Display
module.
See Section 18. On-Screen Display (OSD).
PTE7/DMINUS4
PTE6/DPLUS4
PTE5/DMINUS3
PTE4/4DPLUS3
PTE3/DMINUS2
PTE2/DPLUS2
PTE1/DMINUS1
PTE0/DPLUS1
DPLUS0
DMINUS0
NOTE:
PIN DESCRIPTION
These are shared function, bidirectional I/O port
pins. These pins can be configured as standard
I/O pins or downstream data pins of USB module.
See Section 19. Input/Output (I/O) Ports and
Section 14. Universal Serial Bus Module (USB).
Data pins of USB module upstream port.
See Section 14. Universal Serial Bus Module
(USB).
Any unused inputs and I/O ports should be tied to an appropriate logic level
(either VDD or VSS). Although the I/O ports of the MC68HC908LD64 do not
require termination, termination is recommended to reduce the possibility of
static damage.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
General Description
39
General Description
Data Sheet
40
MC68HC908LD64 — Rev. 3.0
General Description
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 2. Memory Map
2.1 Contents
2.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
2.3
Unimplemented Memory Locations . . . . . . . . . . . . . . . . . . . . . 41
2.4
Reserved Memory Locations . . . . . . . . . . . . . . . . . . . . . . . . . . 42
2.5
Input/Output (I/O) Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
2.2 Introduction
The CPU08 can address 64K-bytes of memory space. The memory
map, shown in Figure 2-1, includes:
•
60,928 bytes of FLASH memory
•
2,048 bytes of random-access memory (RAM)
•
32 bytes of user-defined vectors
•
1,024 + 464 bytes of monitor ROM
2.3 Unimplemented Memory Locations
Accessing an unimplemented location can cause an illegal address
reset if illegal address resets are enabled. In the memory map
(Figure 2-1) and in register figures in this document, unimplemented
locations are shaded.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Memory Map
41
Memory Map
2.4 Reserved Memory Locations
Accessing a reserved location can have unpredictable effects on MCU
operation. In the Figure 2-1 and in register figures in this document,
reserved locations are marked with the word Reserved or with the
letter R.
2.5 Input/Output (I/O) Section
Most of the control, status, and data registers are in the zero page area
of $0000–$007F. Additional I/O registers have these addresses:
•
$FE00; SIM break status register, SBSR
•
$FE01; SIM reset status register, SRSR
•
$FE02; Reserved
•
$FE03; SIM break flag control register, SBFCR
•
$FE04; Interrupt status register 1, INT1
•
$FE05; Interrupt status register 2, INT2
•
$FE06; Reserved
•
$FE07; 47,616 bytes FLASH control register, FLCR
•
$FE08; 47,616 bytes FLASH block protect register, FLBPR
•
$FE09; Reserved
•
$FE0A; 13K-bytes FLASH control register, FLCR1
•
$FE0B; 13K-bytes FLASH block protect register, FLBPR1
•
$FE0C; Break address register high, BRKH
•
$FE0D; Break address register low, BRKL
•
$FE0E; Break status and control register, BRKSCR
•
$FE0F; Reserved
•
$FFFF; COP control register, COPCTL
Data registers are shown in Figure 2-2. Table 2-1 is a list of vector
locations.
Data Sheet
42
MC68HC908LD64 — Rev. 3.0
Memory Map
Freescale Semiconductor
Memory Map
Input/Output (I/O) Section
$0000
I/O Registers
128 Bytes
↓
$007F
$0080
RAM
1,024 Bytes
↓
$047F
$0480
Unimplemented
896 Bytes
↓
$07FF
$0800
OSD RAM
1,024 Bytes
↓
$0BFF
$0C00
↓
$0FFF
$1000
↓
$3FFF
$4000
↓
$F9FF
FLASH Memory
1,024 Bytes
(8 × 128-Byte Blocks)
OSD FLASH Memory
12,288 Bytes
(24 × 512-Byte Blocks)
FLASH Memory
47,616 Bytes
(93 × 512-Byte Blocks)
$FA00
Monitor ROM
1,024 Bytes
↓
$FDFF
$FE00
SIM Break Status Register (SBSR)
$FE01
SIM Reset Status Register (SRSR)
$FE02
Reserved
$FE03
SIM Break Flag Control Register (SBFCR)
$FE04
Interrupt Status Register 1 (INT1)
Figure 2-1. Memory Map
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Memory Map
43
Memory Map
$FE05
Interrupt Status Register 2 (INT2)
$FE06
Reserved
$FE07
47,616 bytes FLASH Control Register (FLCR)
$FE08
47,616 bytes FLASH Block Protect Register (FLBPR)
$FE09
Reserved
$FE0A
13K-bytes FLASH Control Register (FLCR1)
$FE0B
13K-bytes FLASH Block Protect Register (FLBPR1)
$FE0C
Break Address Register High (BRKH)
$FE0D
Break Address Register Low (BRKL)
$FE0E
Break Status and Control Register (BRKSCR)
$FE0F
Reserved
$FE10
↓
Monitor ROM
464 Bytes
$FFDF
$FFE0
↓
FLASH Vectors
32 Bytes
$FFFF
Figure 2-1. Memory Map (Continued)
Data Sheet
44
MC68HC908LD64 — Rev. 3.0
Memory Map
Freescale Semiconductor
Memory Map
Input/Output (I/O) Section
Addr.
Register Name
$0000
Read:
Port A Data Register
Write:
(PTA)
Reset:
$0001
$0002
$0003
Read:
Port B Data Register
Write:
(PTB)
Reset:
Read:
Port C Data Register
Write:
(PTC)
Reset:
Read:
Port D Data Register
Write:
(PTD)
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
PTA7
PTA6
PTA5
PTA4
PTA3
PTA2
PTA1
PTA0
PTB2
PTB1
PTB0
PTC2
PTC1
PTC0
PTD2
PTD1
PTD0
Unaffected by reset
PTB7
0
PTD7
0
0
PTE7
PTC6
PTC5
PTC4
PTC3
PTD6
PTD5
PTD4
PTD3
DDRA6
DDRA5
DDRA4
DDRA3
DDRA2
DDRA1
DDRA0
0
0
0
0
0
0
0
DDRB6
DDRB5
DDRB4
DDRB3
DDRB2
DDRB1
DDRB0
0
0
0
0
0
0
0
DDRC6
DDRC5
DDRC4
DDRC3
DDRC2
DDRC1
DDRC0
0
0
0
0
0
0
0
DDRD6
DDRD5
DDRD4
DDRD3
DDRD2
DDRD1
DDRD0
0
0
0
0
0
0
0
PTE6
PTE5
PTE4
PTE3
PTE2
PTE1
PTE0
Unaffected by reset
Read:
DDRE7
Data Direction Register E
Write:
$0009
(DDRE)
Reset:
0
U = Unaffected
PTB3
Unaffected by reset
Read:
DDRD7
Data Direction Register D
Write:
$0007
(DDRD)
Reset:
0
$0008
PTB4
Unaffected by reset
Read:
DDRB7
Data Direction Register B
$0005
Write:
(DDRB)
Reset:
0
Read:
Port E Data Register
Write:
(PTE)
Reset:
PTB5
Unaffected by reset
Read:
DDRA7
Data Direction Register A
$0004
Write:
(DDRA)
Reset:
0
Read:
Data Direction Register C
$0006
Write:
(DDRC)
Reset:
PTB6
DDRE6
DDRE5
DDRE4
DDRE3
DDRE2
DDRE1
DDRE0
0
0
0
0
0
0
0
= Unimplemented
R
= Reserved
X = Indeterminate
Figure 2-2. Control, Status, and Data Registers (Sheet 1 of 15)
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Memory Map
45
Memory Map
Addr.
6
5
TOIE
TSTOP
0
0
1
0
0
0
0
Read:
TIM Counter Register High
$000C
Write:
(TCNTH)
Reset:
Bit15
Bit14
0
Read:
TIM Counter Register Low
$000D
Write:
(TCNTL)
Reset:
$000A
Register Name
Bit 7
Read:
TIM Status and Control
Register Write:
(TSC)
Reset:
2
1
Bit 0
PS2
PS1
PS0
0
0
0
0
0
0
0
0
0
Bit13
Bit12
Bit11
Bit10
Bit9
Bit8
0
0
0
0
0
0
0
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
0
0
0
0
0
0
0
0
Bit15
Bit14
Bit13
Bit12
Bit11
Bit10
Bit9
Bit8
1
1
1
1
1
1
1
1
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
1
1
1
1
1
1
1
1
CH0IE
MS0B
MS0A
ELS0B
ELS0A
TOV0
CH0MAX
0
0
0
0
0
0
0
0
Bit15
Bit14
Bit13
Bit12
Bit11
Bit10
Bit9
Bit8
Bit2
Bit1
Bit0
TOF
0
4
3
0
0
TRST
Read:
$000B
Unimplemented Write:
Reset:
$000E
$000F
$0010
$0011
$0012
$0013
TIM Counter Modulo Read:
Register High Write:
(TMODH)
Reset:
TIM Counter Modulo Read:
Register Low Write:
(TMODL)
Reset:
TIM Channel 0 Read:
Status and Control Write:
Register
(TSC0) Reset:
Read:
TIM Channel 0
Register High Write:
(TCH0H) Reset:
TIM Channel 0 Read:
Register Low Write:
(TCH0L) Reset:
TIM Channel 1 Read:
Status and Control Write:
Register
(TSC1) Reset:
U = Unaffected
CH0F
0
Indeterminate after reset
Bit7
Bit6
Bit5
Bit4
Bit3
Indeterminate after reset
CH1F
0
0
CH1IE
0
0
0
X = Indeterminate
MS1A
ELS1B
ELS1A
TOV1
CH1MAX
0
0
0
0
0
= Unimplemented
R
= Reserved
Figure 2-2. Control, Status, and Data Registers (Sheet 2 of 15)
Data Sheet
46
MC68HC908LD64 — Rev. 3.0
Memory Map
Freescale Semiconductor
Memory Map
Input/Output (I/O) Section
Addr.
$0014
$0015
$0016
$0017
$0018
$0019
$001A
$001B
$001C
Register Name
Read:
TIM Channel 1
Register High Write:
(TCH1H)
Reset:
Read:
TIM Channel 1
Register Low Write:
(TCH1L)
Reset:
Read:
DDC Master Control
Register Write:
(DDCMCR)
Reset:
Read:
DDC Address Register
Write:
(DDCADR)
Reset:
Read:
DDC Control Register
Write:
(DDCCR)
Reset:
Read:
DDC Status Register
Write:
(DDCSR)
Reset:
DDC Data Transmit Read:
Register Write:
(DDCDTR)
Reset:
DDC Data Receive Read:
Register
Write:
(DDCDRR)
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
Bit15
Bit14
Bit13
Bit12
Bit11
Bit10
Bit9
Bit8
Bit2
Bit1
Bit0
Indeterminate after reset
Bit7
Bit6
Bit5
Bit4
Bit3
Indeterminate after reset
ALIF
NAKIF
BB
MAST
MRW
BR2
BR1
BR0
0
0
0
0
0
0
0
0
DAD7
DAD6
DAD5
DAD4
DAD3
DAD2
DAD1
EXTAD
1
0
1
0
0
0
0
0
DEN
DIEN
0
0
TXAK
SCLIEN
DDC1EN
0
0
0
0
0
0
0
0
RXIF
TXIF
MATCH
SRW
RXAK
SCLIF
TXBE
RXBF
0
0
0
0
0
0
1
0
1
0
DTD7
DTD6
DTD5
DTD4
DTD3
DTD2
DTD1
DTD0
1
1
1
1
1
1
1
1
DRD7
DRD6
DRD5
DRD4
DRD3
DRD2
DRD1
DRD0
0
0
0
0
0
0
0
0
D2AD6
D2AD5
D2AD4
D2AD3
D2AD2
D2AD1
0
0
0
0
0
0
= Unimplemented
R
= Reserved
Read:
D2AD7
DDC2 Address Register
Write:
(DDC2ADR)
Reset:
0
0
0
0
0
Read:
$001D
Unimplemented Write:
Reset:
U = Unaffected
X = Indeterminate
Figure 2-2. Control, Status, and Data Registers (Sheet 3 of 15)
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Memory Map
47
Memory Map
Addr.
$001E
$001F
Register Name
Bit 7
6
5
4
3
2
Read:
IRQ Status and Control
Register Write:
(INTSCR)
Reset:
0
0
0
0
IRQF
0
0
0
0
0
Read:
Configuration Register
Write:
(CONFIG)†
Reset:
0
0
0
0
0
0
0
Read: DE0R07
USB Embedded Device
Endpoint 0 Data Reg. 0 Write: DE0T07
(DE0D0) Reset:
DE0R06
DE0T06
Read: DE0R17
USB Embedded Device
Endpoint 0 Data Reg. 1 Write: DE0T17
(DE0D1) Reset:
DE0R16
DE0R15
DE0R14
DE0T16
DE0T15
DE0T14
Read: DE0R27
USB Embedded Device
Endpoint 0 Data Reg. 2 Write: DE0T27
(DE0D2) Reset:
DE0R26
DE0R25
DE0R24
DE0T26
DE0T25
DE0T24
Read: DE0R37
USB Embedded Device
Endpoint 0 Data Reg. 3 Write: DE0T37
(DE0D3) Reset:
DE0R36
DE0R35
DE0R34
DE0T36
DE0T35
DE0T34
Read: DE0R47
USB Embedded Device
Endpoint 0 Data Reg. 4 Write: DE0T47
(DE0D4) Reset:
DE0R46
DE0R45
DE0R44
DE0T46
DE0T45
DE0T44
USB Embedded Device Read: DE0R57
Endpoint 0 Data Reg. 5 Write: DE0T57
(DE0D5) Reset:
DE0R56
DE0R55
DE0R54
DE0T56
DE0T55
DE0T54
USB Embedded Device Read: DE0R67
Endpoint 0 Data Reg. 6 Write: DE0T67
(DE0D6) Reset:
DE0R66
DE0R65
DE0R64
DE0T66
DE0T65
DE0T64
USB Embedded Device Read: DE0R77
Endpoint 0 Data Reg. 7 Write: DE0T77
(DE0D7) Reset:
DE0R76
DE0R75
DE0R74
DE0T76
DE0T75
DE0T74
ACK
1
Bit 0
IMASK
MODE
0
0
0
0
SSREC
COPRS
STOP
COPD
0
0
0
0
0
DE0R05
DE0R04
DE0R03
DE0R02
DE0R01
DE0R00
DE0T05
DE0T04
DE0T03
DE0T02
DE0T01
DE0T00
DE0R13
DE0R12
DE0R11
DE0R10
DE0T13
DE0T12
DE0T11
DE0T10
DE0R23
DE0R22
DE0R21
DE0R20
DE0T23
DE0T22
DE0T21
DE0T20
DE0R33
DE0R32
DE0R31
DE0R30
DE0T33
DE0T32
DE0T31
DE0T30
DE0R43
DE0R42
DE0R41
DE0R40
DE0T43
DE0T42
DE0T41
DE0T40
DE0R53
DE0R52
DE0R51
DE0R50
DE0T53
DE0T52
DE0T51
DE0T50
DE0R63
DE0R62
DE0R61
DE0R60
DE0T63
DE0T62
DE0T61
DE0T60
DE0R73
DE0R72
DE0R71
DE0R70
DE0T73
DE0T72
DE0T71
DE0T70
R
= Reserved
† One-time writable register after each reset.
$0020
$0021
$0022
$0023
$0024
$0025
$0026
$0027
U = Unaffected
Indeterminate after reset
Indeterminate after reset
Indeterminate after reset
Indeterminate after reset
Indeterminate after reset
Indeterminate after reset
Indeterminate after reset
Indeterminate after reset
X = Indeterminate
= Unimplemented
Figure 2-2. Control, Status, and Data Registers (Sheet 4 of 15)
Data Sheet
48
MC68HC908LD64 — Rev. 3.0
Memory Map
Freescale Semiconductor
Memory Map
Input/Output (I/O) Section
Addr.
6
5
4
3
2
1
Bit 0
Read:
USB Embedded Device
$0028 Endpoint 1/2 Data Reg. 0 Write: DE1T07
(DE1D0)
Reset:
DE1T06
DE1T05
DE1T04
DE1T03
DE1T02
DE1T01
DE1T00
Read:
USB Embedded Device
$0029 Endpoint 1/2 Data Reg. 1 Write: DE1T17
(DE1D1)
Reset:
DE1T16
DE1T12
DE1T11
DE1T10
Read:
USB Embedded Device
$002A Endpoint 1/2 Data Reg. 2 Write: DE1T27
(DE1D2)
Reset:
DE1T26
DE1T22
DE1T21
DE1T20
USB Embedded Device Read:
$002B Endpoint 1/2 Data Reg. 3 Write: DE1T37
(DE1D3)
Reset:
DE1T36
DE1T32
DE1T31
DE1T30
USB Embedded Device Read:
$002C Endpoint 1/2 Data Reg. 4 Write: DE1T47
(DE1D4)
Reset:
DE1T46
DE1T42
DE1T41
DE1T40
USB Embedded Device Read:
$002D Endpoint 1/2 Data Reg. 5 Write: DE1T57
(DE1D5)
Reset:
DE1T56
DE1T52
DE1T51
DE1T50
USB Embedded Device Read:
$002E Endpoint 1/2 Data Reg. 6 Write: DE1T67
(DE1D6)
Reset:
DE1T66
DE1T62
DE1T61
DE1T60
Read:
USB Embedded Device
$002F Endpoint 1/2 Data Reg. 7 Write: DE1T77
(DE1D7)
Reset:
DE1T76
DE1T72
DE1T71
DE1T70
$0030
$0031
Register Name
Bit 7
Indeterminate after reset
DE1T15
DE1T14
DE1T13
Indeterminate after reset
DE1T25
DE1T24
DE1T23
Indeterminate after reset
DE1T35
DE1T34
DE1T33
Indeterminate after reset
DE1T45
DE1T44
DE1T43
Indeterminate after reset
DE1T55
DE1T54
DE1T53
Indeterminate after reset
DE1T65
DE1T64
DE1T63
Indeterminate after reset
DE1T75
DE1T74
DE1T73
Indeterminate after reset
Read: HE0R07
USB HUB Endpoint 0
Data Register 0 Write: HE0T07
(HE0D0) Reset:
HE0R06
HE0R05
HE0R04
HE0R03
HE0R02
HE0R01
HE0R00
HE0T06
HE0T05
HE0T04
HE0T03
HE0T02
HE0T01
HE0T00
Read: HE0R17
USB HUB Endpoint 0
Data Register 1 Write: HE0T17
(HE0D1) Reset:
HE0R16
HE0R15
HE0R14
HE0R13
HE0R12
HE0R11
HE0R10
HE0T16
HE0T15
HE0T14
HE0T13
HE0T12
HE0T11
HE0T10
R
= Reserved
U = Unaffected
Indeterminate after reset
Indeterminate after reset
X = Indeterminate
= Unimplemented
Figure 2-2. Control, Status, and Data Registers (Sheet 5 of 15)
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Memory Map
49
Memory Map
Addr.
Register Name
$0032
$0033
$0034
$0035
$0036
$0037
$0038
$0039
5
4
3
2
1
Bit 0
Read: HE0R27
USB HUB Endpoint 0
Data Register 2 Write: HE0T27
(HE0D2)
Reset:
HE0R26
HE0R25
HE0R24
HE0R23
HE0R22
HE0R21
HE0R20
HE0T26
HE0T25
HE0T24
HE0T23
HE0T22
HE0T21
HE0T20
Read: HE0R37
USB HUB Endpoint 0
Data Register 3 Write: HE0T37
(HE0D3)
Reset:
HE0R36
HE0R35
HE0R34
HE0R33
HE0R32
HE0R31
HE0R30
HE0T36
HE0T35
HE0T34
HE0T33
HE0T32
HE0T31
HE0T30
Read: HE0R47
USB HUB Endpoint 0
Data Register 4 Write: HE0T47
(HE0D4)
Reset:
HE0R46
HE0R45
HE0R44
HE0R43
HE0R42
HE0R41
HE0R40
HE0T46
HE0T45
HE0T44
HE0T43
HE0T42
HE0T41
HE0T40
USB HUB Endpoint 0 Read: HE0R57
Data Register 5 Write: HE0T57
(HE0D5)
Reset:
HE0R56
HE0R55
HE0R54
HE0R53
HE0R52
HE0R51
HE0R50
HE0T56
HE0T55
HE0T54
HE0T53
HE0T52
HE0T51
HE0T50
USB HUB Endpoint 0 Read: HE0R67
Data Register 6 Write: HE0T67
(HE0D6)
Reset:
HE0R66
HE0R65
HE0R64
HE0R63
HE0R62
HE0R61
HE0R60
HE0T66
HE0T65
HE0T64
HE0T63
HE0T62
HE0T61
HE0T60
USB HUB Endpoint 0 Read: HE0R77
Data Register 7 Write: HE0T77
(HE0D7)
Reset:
HE0R76
HE0R75
HE0R74
HE0R73
HE0R72
HE0R71
HE0R70
HE0T76
HE0T75
HE0T74
HE0T73
HE0T72
HE0T71
HE0T70
1
1
1
1
1
1
1
1
0
0
0
0
Read:
PLL Bandwidth Control
Register Write:
(PBWC) Reset:
Read:
PLL Programming
Register Write:
(PPG) Reset:
$003A
$003B
6
Read:
PLL Control Register
Write:
(PCTL)
Reset:
Read:
ADC Status and Control
Register Write:
(ADSCR)
Reset:
U = Unaffected
Bit 7
PLLIE
0
AUTO
Indeterminate after reset
Indeterminate after reset
Indeterminate after reset
Indeterminate after reset
Indeterminate after reset
Indeterminate after reset
PLLF
0
LOCK
PLLON
BCS
1
0
ACQ
XLD
0
0
0
0
0
0
0
0
MUL7
MUL6
MUL5
MUL4
VRS7
VRS6
VRS5
VRS4
0
1
1
0
0
1
1
0
AIEN
ADCO
ADCH4
ADCH3
ADCH2
ADCH1
ADCH0
0
0
1
1
1
1
1
= Unimplemented
R
= Reserved
COCO
0
X = Indeterminate
Figure 2-2. Control, Status, and Data Registers (Sheet 6 of 15)
Data Sheet
50
MC68HC908LD64 — Rev. 3.0
Memory Map
Freescale Semiconductor
Memory Map
Input/Output (I/O) Section
Addr.
$003C
Register Name
Read:
ADC Data Register
Write:
(ADR)
Reset:
Read:
ADC Input Clock Register
$003D
Write:
(ADICLK)
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
AD7
AD6
AD5
AD4
AD3
AD2
AD1
AD0
Indeterminate after reset
ADIV2
ADIV1
ADIV0
0
0
0
0
0
0
0
0
0
0
0
0
0
Read:
$003E
Unimplemented Write:
Reset:
H & V Sync Output Control Read:
$003F
Register Write:
(HVOCR)
Reset:
$0040
$0041
$0042
$0043
$0044
Sync Processor Control Read:
and Status Register Write:
(SPCSR)
Reset:
DCLKPH1 DCLKPH0
VSIF
R
0
0
COMP
VINVO
HINVO
HVOCR1 HVOCR0
0
0
VPOL
HPOL
VSIE
VEDGE
0
0
0
0
0
0
0
0
Vertical Frequency High Read:
Register Write:
(VFHR)
Reset:
VOF
0
0
VF12
VF11
VF10
VF9
VF8
CPW1
CPW0
0
0
0
0
0
0
0
0
Vertical Frequency Low Read:
Register Write:
(VFLR)
Reset:
VF7
VF6
VF5
VF4
VF3
VF2
VF1
VF0
0
0
0
0
0
0
0
0
Read:
Hsync Frequency High
Register Write:
(HFHR) Reset:
HFH7
HFH6
HFH5
HFH4
HFH3
HFH2
HFH1
HFH0
0
0
0
0
0
0
0
0
0
0
HFL4
HFL3
HFL2
HFL1
HFL0
0
0
0
0
0
0
0
COINV
R
R
R
BPOR
SOUT
0
0
Read: HOVER
Hsync Frequency Low
Register Write:
(HFLR) Reset:
0
Read: VSYNCS HSYNCS
Sync Processor I/O Control
$0045
Register Write:
(SPIOCR) Reset:
0
0
U = Unaffected
0
0
X = Indeterminate
= Unimplemented
R
= Reserved
Figure 2-2. Control, Status, and Data Registers (Sheet 7 of 15)
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Memory Map
51
Memory Map
Addr.
$0046
$0047
$0048
$0049
$004A
$004B
$004C
$004D
Register Name
Read:
Sync Processor Control
Register 1 Write:
(SPCR1)
Reset:
Bit 7
LVSIE
6
LVSIF
0
5
4
3
2
1
Bit 0
HPS1
HPS0
R
R
ATPOL
FSHF
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DADD6
DADD5
DADD4
DADD3
DADD2
DADD1
DADD0
0
0
0
0
0
0
0
USB Embedded Device Read: TXD0F
Interrupt Register 0 Write:
(DIR0)
Reset:
0
RXD0F
0
0
TXD0IE
RXD0IE
0
0
TXD0FR
RXD0FR
0
0
0
0
0
0
0
USB Embedded Device Read: TXD1F
Interrupt Register 1 Write:
(DIR1)
Reset:
0
0
0
0
0
0
0
USB Embedded Device Read:
Control Register 2 Write:
(DCR2)
Reset:
USB Embedded Device Read: DEVEN
Address Register Write:
(DADDR)
Reset:
0
USB Embedded Device Read: T0SEQ
Control Register 0 Write:
(DCR0)
Reset:
0
USB Embedded Device Read: T1SEQ
Control Register 1 Write:
(DCR1)
Reset:
0
Read: DRSEQ
USB Embedded Device
Status Register Write:
(DSR) Reset:
0
$004E
Read:
Keyboard Status and
Control Register Write:
(KBSCR) Reset:
Read:
Keyboard Interrupt Enable
$004F
Register Write:
(KBIER) Reset:
U = Unaffected
0
ENABLE2 ENABLE1 DSTALL2 DSTALL1
TXD1IE
TXD1FR
0
0
0
0
0
0
0
DSTALL0
TX0E
RX0E
TP0SIZ3
TP0SIZ2
TP0SIZ1
TP0SIZ0
0
0
0
0
0
0
0
ENDADD
TX1E
TP1SIZ3
TP1SIZ2
TP1SIZ1
TP1SIZ0
0
0
0
0
0
0
0
DSETUP
DTX1ST
0
RP0SIZ3
RP0SIZ2
RP0SIZ1
RP0SIZ0
0
0
IMASKK
MODEK
0
DTX1STR
0
0
0
0
0
0
0
0
KEYF
0
ACKK
0
0
0
0
0
0
0
0
KBIE7
KBIE6
KBIE5
KBIE4
KBIE3
KBIE2
KBIE1
KBIE0
0
0
0
0
0
0
0
0
= Unimplemented
R
= Reserved
X = Indeterminate
Figure 2-2. Control, Status, and Data Registers (Sheet 8 of 15)
Data Sheet
52
MC68HC908LD64 — Rev. 3.0
Memory Map
Freescale Semiconductor
Memory Map
Input/Output (I/O) Section
Addr.
Register Name
Bit 7
6
5
4
3
2
1
Bit 0
PEN1
LOWSP1
RST1
RESUM1
SUSP1
0
D1+
D1–
0
0
0
0
0
0
X
X
PEN2
LOWSP2
RST2
RESUM2
SUSP2
0
D2+
D2–
0
0
0
0
0
0
X
X
PEN3
LOWSP3
RST3
RESUM3
SUSP3
0
D3+
D3–
0
0
0
0
0
0
X
X
PEN4
LOWSP4
RST4
RESUM4
SUSP4
0
D4+
D4–
0
0
0
0
0
0
X
X
USB SIE Timing Interrupt Read:
$0056
Register Write:
(SIETIR)
Reset:
SOFF
EOF2F
EOPF
TRANF
SOFIE
EOF2IE
EOPIE
TRANIE
0
0
0
0
0
0
0
0
Read:
USB SIE Timing Status
Register Write:
(SIETSR) Reset:
RSTF
0
LOCKF
0
0
0
0
0
LOCKFR
SOFFR
EOF2FR
EOPFR
TRANFR
Read:
$0050
Unimplemented Write:
Reset:
$0051
$0052
$0053
$0054
Read:
USB HUB Downstream
Port 1 Control Register Write:
(HDP1CR)
Reset:
USB HUB Downstream Read:
Port 2 Control Register Write:
(HDP2CR)
Reset:
USB HUB Downstream Read:
Port 3 Control Register Write:
(HDP3CR)
Reset:
USB HUB Downstream Read:
Port 4 Control Register Write:
(HDP4CR)
Reset:
Read:
$0055
Unimplemented Write:
Reset:
$0057
$0058
RSTFR
0*
Read:
USB HUB Address
USBEN
Register Write:
(HADDR) Reset:
0*
0
0
0
0
0
0
0
ADD6
ADD5
ADD4
ADD3
ADD2
ADD1
ADD0
0
0
0
0
0
0
0
0
0
TXDIE
RXDIE
0
0
TXDFR
RXDFR
0
0
0
0
= Unimplemented
R
= Reserved
* RSTF and USBEN are reset by a power-on reset (POR) only.
$0059
USB HUB Interrupt Read:
Register 0 Write:
(HIR0)
Reset:
U = Unaffected
TXDF
0
RXDF
0
0
X = Indeterminate
0
Figure 2-2. Control, Status, and Data Registers (Sheet 9 of 15)
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Memory Map
53
Memory Map
Addr.
Register Name
Bit 7
6
5
4
3
2
1
Bit 0
TSEQ
STALL0
TXE
RXE
TPSIZ3
TPSIZ2
TPSIZ1
TPSIZ0
0
0
0
0
0
0
0
0
PNEW
PCHG5
PCHG4
PCHG3
PCHG2
PCHG1
PCHG0
0
0
0
0
0
0
0
SETUP
TX1ST
0
RPSIZ3
RPSIZ2
RPSIZ1
RPSIZ0
X
X
X
X
0
D0+
D0–
0
X
X
Read:
Unimplemented Reset:
$005A
Reset:
Read:
USB HUB Control
Register 0 Write:
(HCR0)
Reset:
$005B
Read:
USB HUB Endpoint 1
STALL1
$005C Control and Data Register Write:
(HCDR)
Reset:
0
Read:
USB HUB Status Register
$005D
Write:
(HSR)
Reset:
USB HUB Root Port Read:
Control Register Write:
(HRPCR)
Reset:
$005E
RSEQ
TX1STR
X
X
X
0
0
0
0
0
0
0
0
0
R
OSDRST
CLKINV
CLKPH1
0
0
0
RESUM0 SUSPND
Read:
$005F
Unimplemented Write:
Reset:
$0060
Read:
OSDMEN
OSD Control Register
Write:
(OSDCR)
Reset:
0
Read:
OSD Status Register
Write:
(OSDSR)
Reset:
$0061
$0062
$0063
0
0
0
WRDY
DENDIF
1
0
Read:
OSDD7
OSD Data Register Low
Write:
(OSDDRL)
Reset:
Read:
OSDD15
OSD Data Register High
Write:
(OSDDRH)
Reset:
U = Unaffected
CLKPH0 HALFCLK OSDIEN
OSDD6
OSDD5
OSDD4
OSDD3
OSDD2
OSDD1
OSDD0
OSDD10
OSDD9
OSDD8
R
= Reserved
Unaffected by reset
OSDD14
OSDD13
OSDD12
OSDD11
Unaffected by reset
X = Indeterminate
= Unimplemented
Figure 2-2. Control, Status, and Data Registers (Sheet 10 of 15)
Data Sheet
54
MC68HC908LD64 — Rev. 3.0
Memory Map
Freescale Semiconductor
Memory Map
Input/Output (I/O) Section
Addr.
$0064
$0065
$0066
Register Name
Bit 7
6
5
4
3
2
1
Bit 0
ROWA3
ROWA2
ROWA1
ROWA0
0
0
0
0
COLA4
COLA3
COLA2
COLA1
COLA0
0
0
0
0
0
DOT12
DOT11
DOT10
DOT9
DOT8
Read:
OSD Row Address
Register Write:
(OSDRAR)
Reset:
Read:
OSD Column Address
Register Write:
(OSDCAR)
Reset:
Read:
OSD FLASH Even
DOT15
High Byte Write Buffer Write:
(OSDEHBUF)
Reset:
DOT14
DOT13
Unaffected by reset
Read:
$0067
Unimplemented Write:
Reset:
$0068
$0069
$006A
$006B
$006C
$006D
Port E Control Read:
Register Write:
(PECR)
Reset:
R
0
Port D Control Read: IICDATE
Register Write:
(PDCR)
Reset:
0
IICSCLE DDCDATE DDCSCLE HOUTE
0
Read:
Multi-Master IIC Address
MMAD7
Register Write:
(MMADR) Reset:
1
U = Unaffected
0
VOUTE
DEE
DCLKE
0
0
0
MMAST
MMRW
MMBR2
MMBR1
MMBR0
0
0
0
0
0
0
MMAD6
MMAD5
MMAD4
MMAD3
MMAD2
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
MMIEN
0
0
Read: MMRXIF
Multi-Master IIC
0
Status Register Write:
(MMSR) Reset:
0
0
0
MMEN
MMTXIF
0
0
0
Multi-Master IIC Read: MMALIF MMNAKIF
Master Control Register Write:
0
0
(MIMCR)
Reset:
0
0
Read:
Multi-Master IIC Control
Register Write:
(MMCR)
Reset:
USBDS4E USBDS3E USBDS2E USBDS1E
MMBB
MMTXAK
0
MMATCH MMSRW MMRXAK
0
MMAD1 MMEXTAD
MMTXBE MMRXBF
0
0
0
X = Indeterminate
0
1
0
1
0
= Unimplemented
R
= Reserved
Figure 2-2. Control, Status, and Data Registers (Sheet 11 of 15)
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Memory Map
55
Memory Map
Addr.
$006E
$006F
Register Name
Bit 7
Read:
Multi-Master IIC
MMTD7
Data Transmit Register Write:
(MMDTR)
Reset:
1
Multi-Master IIC Read: MMRD7
Data Receive Register
Write:
(MMDRR)
Reset:
0
$0070
$0071
$0072
$0073
$0074
$0075
$0076
$0077
Read:
0PWM4
PWM0 Data Register
Write:
(0PWM)
Reset:
0
Read:
1PWM4
PWM1 Data Register
Write:
(1PWM)
Reset:
0
Read:
2PWM4
PWM2 Data Register
Write:
(2PWM)
Reset:
0
Read:
3PWM4
PWM3 Data Register
Write:
(3PWM)
Reset:
0
Read:
4PWM4
PWM4 Data Register
Write:
(4PWM)
Reset:
0
Read:
5PWM4
PWM5 Data Register
Write:
(5PWM)
Reset:
0
Read:
6PWM4
PWM6 Data Register
Write:
(6PWM)
Reset:
0
Read:
7PWM4
PWM7 Data Register
Write:
(7PWM)
Reset:
0
U = Unaffected
6
5
4
3
2
1
Bit 0
MMTD6
MMTD5
MMTD4
MMTD3
MMTD2
MMTD1
MMTD0
1
1
1
1
1
1
1
MMRD6
MMRD5
MMRD4
MMRD3
MMRD2
MMRD1
MMRD0
0
0
0
0
0
0
0
0PWM3
0PWM2
0PWM1
0PWM0
0BRM2
0BRM1
0BRM0
0
0
0
0
0
0
0
1PWM3
1PWM2
1PWM1
1PWM0
1BRM2
1BRM1
1BRM0
0
0
0
0
0
0
0
2PWM3
2PWM2
2PWM1
2PWM0
2BRM2
2BRM1
2BRM0
0
0
0
0
0
0
0
3PWM3
3PWM2
3PWM1
3PWM0
3BRM2
3BRM1
3BRM0
0
0
0
0
0
0
0
4PWM3
4PWM2
4PWM1
4PWM0
4BRM2
4BRM1
4BRM0
0
0
0
0
0
0
0
5PWM3
5PWM2
5PWM1
5PWM0
5BRM2
5BRM1
5BRM0
0
0
0
0
0
0
0
6PWM3
6PWM2
6PWM1
6PWM0
6BRM2
6BRM1
6BRM0
0
0
0
0
0
0
0
7PWM3
7PWM2
7PWM1
7PWM0
7BRM2
7BRM1
7BRM0
0
0
0
0
0
0
0
= Unimplemented
R
= Reserved
X = Indeterminate
Figure 2-2. Control, Status, and Data Registers (Sheet 12 of 15)
Data Sheet
56
MC68HC908LD64 — Rev. 3.0
Memory Map
Freescale Semiconductor
Memory Map
Input/Output (I/O) Section
Addr.
$0078
Register Name
Bit 7
Read:
PWM7E
PWM Control Register
Write:
(PWMCR)
Reset:
0
6
5
4
3
2
1
Bit 0
PWM6E
PWM5E
PWM4E
PWM3E
PWM2E
PWM1E
PWM0E
0
0
0
0
0
0
0
R
R
R
R
R
Read:
$0079
Unimplemented Write:
Reset:
Read:
$007A
Unimplemented Write:
Reset:
Read:
$007B
Unimplemented Write:
Reset:
Read:
$007C
Unimplemented Write:
Reset:
Read:
$007D
Unimplemented Write:
Reset:
Read:
$007E
Unimplemented Write:
Reset:
Read:
$007F
Unimplemented Write:
Reset:
Read:
SIM Break Status Register
$FE00
Write:
(SBSR)
Reset:
R
SBSW
R
Note
0
Note: Writing a logic 0 clears SBSW.
U = Unaffected
X = Indeterminate
= Unimplemented
R
= Reserved
Figure 2-2. Control, Status, and Data Registers (Sheet 13 of 15)
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Memory Map
57
Memory Map
Addr.
Register Name
Bit 7
6
5
4
3
2
1
Bit 0
Read:
SIM Reset Status Register
Write:
$FE01
(SRSR)
POR:
POR
PIN
COP
ILOP
ILAD
USB
0
0
1
0
0
0
0
0
0
0
R
R
R
R
R
R
R
R
BCFE
R
R
R
R
R
R
R
Read:
$FE02
Reserved Write:
Reset:
$FE03
SIM Break Flag Control Read:
Register Write:
(SBFCR)
Reset:
0
Read:
Interrupt Status Register 1
$FE04
Write:
(INT1)
Reset:
IF6
IF5
IF4
IF3
IF2
IF1
0
0
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
Read:
Interrupt Status Register 2
$FE05
Write:
(INT2)
Reset:
IF14
IF13
IF12
IF11
IF10
IF9
IF8
IF7
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
R
R
R
R
R
R
R
R
0
0
0
0
HVEN
MASS
ERASE
PGM
0
0
0
0
0
0
0
0
BPR7
BPR6
BPR5
BPR4
BPR3
BPR2
BPR1
0
0
0
0
0
0
0
0
R
R
R
R
R
R
R
R
0
0
0
0
HVEN1
MASS1
ERASE1
PGM1
0
0
0
0
0
0
0
0
= Unimplemented
R
= Reserved
Read:
$FE06
Reserved Write:
Reset:
47,616 Bytes FLASH Read:
Control Register Write:
(FLCR)
Reset:
$FE07
$FE08
Read:
47,616 Bytes FLASH
Block Protect Register Write:
(FLBPR) Reset:
Read:
$FE09
Reserved Write:
0
Reset:
$FE0A
Read:
13K-Bytes FLASH
Control Register Write:
(FLCR1) Reset:
U = Unaffected
X = Indeterminate
Figure 2-2. Control, Status, and Data Registers (Sheet 14 of 15)
Data Sheet
58
MC68HC908LD64 — Rev. 3.0
Memory Map
Freescale Semiconductor
Memory Map
Input/Output (I/O) Section
Addr.
$FE0B
$FE0C
$FE0D
Register Name
6
5
4
3
2
1
BPR16
BPR15
BPR14
BPR13
BPR12
BPR11
0
0
0
0
0
0
0
Bit 15
14
13
12
11
10
9
Bit 8
0
0
0
0
0
0
0
0
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
BRKE
BRKA
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Read:
13K-Bytes FLASH
BPR17
Block Protect Register Write:
(FLBPR1)
Reset:
0
Read:
Break Address High
Write:
Register (BRKH)
Reset:
Read:
Break Address Low
Write:
Register (BRKL)
Reset:
Break Status and Control Read:
$FE0E
Register Write:
(BRKSCR)
Reset:
$FFFF
Bit 7
Read:
COP Control Register
Write:
(COPCTL)
Reset:
U = Unaffected
Bit 0
0
Low byte of reset vector
Writing clears COP counter (any value)
Unaffected by reset
X = Indeterminate
= Unimplemented
R
= Reserved
Figure 2-2. Control, Status, and Data Registers (Sheet 15 of 15)
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Memory Map
59
Memory Map
.
Table 2-1. Vector Addresses
Vector Priority
Lowest
Vector
IF14
IF13
IF12
IF11
IF10
IF9
IF8
IF7
IF6
IF5
IF4
IF3
IF2
IF1
—
Highest
—
Address
$FFE0
CGM PLL Interrupt Vector (High)
$FFE1
CGM PLL Interrupt Vector (Low)
$FFE2
Keyboard Interrupt Vector (High)
$FFE3
Keyboard Interrupt Vector (Low)
$FFE4
ADC Interrupt Vector (High)
$FFE5
ADC Interrupt Vector (Low)
$FFE6
OSD Interrupt Vector (High)
$FFE7
OSD Interrupt Vector (Low)
$FFE8
MMIIC Vector (High)
$FFE9
MMIIC Vector (Low)
$FFEA
Sync Processor Vector (High)
$FFEB
Sync Processor Vector (Low)
$FFEC
TIM Overflow Vector (High)
$FFED
TIM Overflow Vector (Low)
$FFEE
TIM Channel 1 Vector (High)
$FFEF
TIM Channel 1 Vector (Low)
$FFF0
TIM Channel 0 Vector (High)
$FFF1
TIM Channel 0 Vector (Low)
$FFF2
DDC12AB Vector (High)
$FFF3
DDC12AB Vector (Low)
$FFF4
USB Device Interrupt Vector (High)
$FFF5
USB Device Interrupt Vector (Low)
$FFF6
USB HUB Interrupt Vector (High)
$FFF7
USB HUB Interrupt Vector (Low)
$FFF8
USB Vector (High)
$FFF9
USB Vector (Low)
$FFFA
IRQ Vector (High)
$FFFB
IRQ Vector (Low)
$FFFC
SWI Vector (High)
$FFFD
SWI Vector (Low)
$FFFE
Reset Vector (High)
$FFFF
Reset Vector (Low)
Data Sheet
60
Vector
MC68HC908LD64 — Rev. 3.0
Memory Map
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 3. Random-Access Memory (RAM)
3.1 Contents
3.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
3.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
3.2 Introduction
This section describes the 2,048 bytes of RAM (random-access
memory).
3.3 Functional Description
The RAM is divided into two blocks. Addresses $0080 through $047F
are locations for general use. Addresses $0800 through $0BFF are
locations for the OSD display RAM (see 18.6 OSD Screen Memory
Map). The location of the stack RAM is programmable. The 16-bit stack
pointer allows the stack to be anywhere in the 64-Kbyte memory space.
NOTE:
For correct operation, the stack pointer must point only to RAM
locations.
Within page zero are 128 bytes of RAM. Because the location of the
stack RAM is programmable, all page zero RAM locations can be used
for I/O control and user data or code. When the stack pointer is moved
from its reset location at $00FF out of page zero, direct addressing mode
instructions can efficiently access all page zero RAM locations. Page
zero RAM, therefore, provides ideal locations for frequently accessed
global variables.
Before processing an interrupt, the CPU uses five bytes of the stack to
save the contents of the CPU registers.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Random-Access Memory (RAM)
61
Random-Access Memory (RAM)
NOTE:
For M6805 compatibility, the H register is not stacked.
During a subroutine call, the CPU uses two bytes of the stack to store
the return address. The stack pointer decrements during pushes and
increments during pulls.
NOTE:
Be careful when using nested subroutines. The CPU may overwrite data
in the RAM during a subroutine or during the interrupt stacking
operation.
Data Sheet
62
MC68HC908LD64 — Rev. 3.0
Random-Access Memory (RAM)
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 4. FLASH Memory
4.1 Contents
4.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
4.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
4.4
FLASH Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
4.4.1
OSD FLASH Even High Byte Write Buffer (OSDEHBUF) . . 67
4.5
FLASH Block Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . 68
4.6
FLASH Mass Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . 69
4.7
FLASH Program Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . .70
4.8
FLASH Block Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
4.8.1
FLASH Block Protect Registers . . . . . . . . . . . . . . . . . . . . . . 72
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
FLASH Memory
63
FLASH Memory
4.2 Introduction
This section describes the operation of the embedded FLASH memory.
This memory can be read, programmed, and erased from a single
external supply. The program and erase operations are enabled through
the use of an internal charge pump.
Addr.
Register Name
$FE07
47,616 Bytes FLASH Read:
Control Register Write:
(FLCR)
Reset:
$FE08
47,616 Bytes FLASH Read:
Block Protect Register Write:
(FLBPR)
Reset:
13K-Bytes FLASH Read:
Control Register Write:
(FLCR1)
Reset:
$FE0A
$FE0B
$0066
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
HVEN
MASS
ERASE
PGM
0
0
0
0
0
0
0
0
BPR7
BPR6
BPR5
BPR4
BPR3
BPR2
BPR1
0
0
0
0
0
0
0
0
0
0
0
0
HVEN1
MASS1
ERASE1
PGM1
0
0
0
0
0
0
0
0
BPR16
BPR15
BPR14
BPR13
BPR12
BPR11
0
0
0
0
0
0
0
DOT14
DOT13
DOT12
DOT11
DOT10
DOT9
DOT8
13K-Bytes FLASH Read: BPR17
Block Protect Register Write:
(FLBPR1)
Reset:
0
OSD FLASH Even Read: DOT15
High Byte Write Buffer Write:
(OSDEHBUF)
Reset:
0
0
Unaffected by reset
Figure 4-1. FLASH I/O Register Summary
4.3 Functional Description
The MC68HC908LD64 FLASH memory contains two arrays:
•
13,312-byte array
•
47,616-byte array
An additional 32 bytes of FLASH user vectors, $FFE0–$FFFF, are in the
same array as the 47,616-byte. The size, address range, and memory
usage of the arrays are summarized in Table 4-1.
NOTE:
An erased bit reads as logic 1 and a programmed bit reads as logic 0.
Data Sheet
64
MC68HC908LD64 — Rev. 3.0
FLASH Memory
Freescale Semiconductor
FLASH Memory
Functional Description
Table 4-1. FLASH Memory Array Summary
13,312 Array
47,616 Array
Bytes
1,024
12,288
47,616
32
Address range
$0C00–$0FFF
$1000–$3FFF
$4000–$F9FF
$FFE0–$FFFF
Minimum erase size
128 bytes
512 bytes
512 bytes
32 bytes by mass
erase only
Usage
User data or
program
OSD fonts
User program
User vectors
Programming Size
Double bytes in a 64-byte
programming routine
Single bytes in a 64-byte
programming routine
Related Control registers
FLCR1 at $FE0A
FLBPR1 at $FE0B
OSDEHBUF at $0066
FLCR at $FE07
FLBPR at $FE08
Each FLASH array is programmed and erased through control bits in
their respective memory mapped FLASH control registers, FLCR and
FLCR1.
The 13K-bytes array is programmed in double bytes. Programming an
odd address ($xxxx+1) location automatically programs the content in
the OSD FLASH even high byte write buffer (OSDEHBUF) to the even
address ($xxxx) location.
Programming tools are available from Freescale. Contact your local
Freescale representative for more information.
NOTE:
A security feature prevents viewing of the FLASH contents.1
1. No security feature is absolutely secure. However, Freescale’s strategy is to make reading or
copying the FLASH difficult for unauthorized users.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
FLASH Memory
65
FLASH Memory
4.4 FLASH Control Registers
The two FLASH control registers control FLASH program and erase
operations.
This register controls the 47,616-byte array:
Address:
Read:
$FE07
Bit 7
6
5
4
0
0
0
0
3
2
1
Bit 0
HVEN
MASS
ERASE
PGM
0
0
0
0
Write:
Reset:
0
0
0
0
= Unimplemented
Figure 4-2. 47,616-byte FLASH Control Register (FLCR)
This register controls the 13K-byte array:
Address:
Read:
$FE0A
Bit 7
6
5
4
0
0
0
0
3
2
1
Bit 0
HVEN1
MASS1
ERASE1
PGM1
0
0
0
0
Write:
Reset:
0
0
0
0
= Unimplemented
Figure 4-3. 13K-byte FLASH Control Register (FLCR1)
FLCR1 is used with the OSD FLASH even high byte write buffer
(OSDEHBUF) in programming operations. See 4.4.1 OSD FLASH Even
High Byte Write Buffer (OSDEHBUF).
The following are bit definitions for FLCR and FLCR1.
HVEN — High-Voltage Enable Bit
This read/write bit enables the charge pump to drive high voltages for
program and erase operations in the array. HVEN can only be set if
either PGM = 1 or ERASE = 1 and the proper sequence for program
or erase is followed.
1 = High voltage enabled to array and charge pump on
0 = High voltage disabled to array and charge pump off
Data Sheet
66
MC68HC908LD64 — Rev. 3.0
FLASH Memory
Freescale Semiconductor
FLASH Memory
FLASH Control Registers
MASS — Mass Erase Control Bit
This read/write bit configures the memory for mass erase operation or
block erase operation when the ERASE bit is set.
1 = Mass Erase operation selected
0 = Mass Erase operation not selected
ERASE — Erase Control Bit
This read/write bit configures the memory for erase operation. ERASE
is interlocked with the PGM bit such that both bits cannot be equal to
1 or set to 1 at the same time.
1 = Erase operation selected
0 = Erase operation not selected
PGM — Program Control Bit
This read/write bit configures the memory for program operation.
PGM is interlocked with the ERASE bit such that both bits cannot be
equal to 1 or set to 1 at the same time.
1 = Program operation selected
0 = Program operation not selected
4.4.1 OSD FLASH Even High Byte Write Buffer (OSDEHBUF)
Address:
$0066
Bit 7
6
5
4
3
2
1
0
DOT15
DOT14
DOT13
DOT12
DOT11
DOT10
DOT9
DOT8
Read:
Write:
Reset:
Unaffected by reset
Figure 4-4. OSD FLASH Even High Byte Write Buffer (OSDEHBUF)
DOT[15:8] — OSD FLASH Even High Byte Buffer
These bits define the byte to be programmed to an even address
location of the 13K-bytes array. The contents of this register will be
automatically programmed to the even address ($xxxx) location when
the odd address ($xxxx+1) is programmed. Reset has no effect on these
bits. See 18.5 OSD FLASH Font Memory Map for OSD font memory
map.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
FLASH Memory
67
FLASH Memory
4.5 FLASH Block Erase Operation
The minimum erase size for the FLASH memory is one block, and is
carried out by the block erase operation. For memory $0C00–$0FFF, a
block consists of 128 consecutive bytes starting from addresses $xx00
or $xx80. For memory $1000–$3FFF and $4000–$F9FF, a block
consists of 512 consecutive bytes starting from addresses $x000,
$x200, $x400, $x600, $x800, $xA00, $xC00, or $xE00.
NOTE:
The 32-byte user vectors, $FFE0–$FFFF, cannot be erased by the block
erase operation because of security reasons. Mass erase is required to
erase this block.
Use the following procedure to erase a block of FLASH memory:
1. Set the ERASE bit, and clear the MASS bit in the FLASH control
register.
2. Write any data to any FLASH address within the block address
range desired.
3. Wait for a time, tnvs (min. 5µs)
4. Set the HVEN bit.
5. Wait for a time, tErase (min. 10ms)
6. Clear the ERASE bit.
7. Wait for a time, tnvh (min. 5µs)
8. Clear the HVEN bit.
9. After a time, trcv (min. 1µs), the memory can be accessed again in
read mode.
NOTE:
Programming and erasing of FLASH locations cannot be performed by
code being executed from the same FLASH array that is being
programmed or erased. While these operations must be performed in
the order as shown, but other unrelated operations may occur between
the steps.
Data Sheet
68
MC68HC908LD64 — Rev. 3.0
FLASH Memory
Freescale Semiconductor
FLASH Memory
FLASH Mass Erase Operation
4.6 FLASH Mass Erase Operation
A mass erase operation erases an entire array of FLASH memory. The
MC68HC908LD64 contains two FLASH memory arrays, therefore, two
mass erase operations are required to erase all FLASH memory in the
device. Mass erasing the 13K-byte array, erases all FLASH memory
from $0800 to $3FFF. Mass erasing the 47,616-byte array, erases all
FLASH memory from $4000 to $FFFF.
Use the following procedure to erase an entire FLASH memory array:
1. Set both the ERASE bit, and the MASS bit in the FLASH control
register.
2. Write any data to any FLASH address within the FLASH memory
address range.
3. Wait for a time, tnvs (5µs).
4. Set the HVEN bit.
5. Wait for a time, tERASE (10ms).
6. Clear the ERASE bit.
7. Wait for a time, tnvhl (100µs).
8. Clear the HVEN bit.
9. After time, trcv (1µs), the memory can be accessed again in read
mode.
NOTE:
Programming and erasing of FLASH locations cannot be performed by
code being executed from the same FLASH array that is being
programmed or erased. While these operations must be performed in
the order as shown, but other unrelated operations may occur between
the steps.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
FLASH Memory
69
FLASH Memory
4.7 FLASH Program Operation
Programming of the FLASH memory is done on a row basis. A row
consists of 64 consecutive bytes starting from addresses $XX00,
$XX40, $XX80, and $XXC0. Use this step-by-step procedure to program
a row of FLASH memory (Figure 4-5 is a flowchart representation):
NOTE:
In order to avoid program disturbs, the row must be erased before any
byte on that row is programmed.
1. Set the PGM bit. This configures the memory for program
operation and enables the latching of address and data for
programming.
2. Write any data to any FLASH address within the row address
range desired.
3. Wait for a time, tnvs (min. 5µs).
4. Set the HVEN bit.
5. Wait for a time, tpgs (min. 10µs).
6. For 47,616-byte array: Write data to the FLASH address to be
programmed.
For 13K-byte array: Write even address data to OSDEHBUF
then write odd address data to the odd
FLASH address to be programmed.
7. Wait for time, tPROG (min. 20µs).
8. Repeat step 6 and 7 until all the bytes within the row are
programmed.
9. Clear the PGM bit.
10. Wait for time, tnvh (min. 5µs).
11. Clear the HVEN bit.
12. After time, trcv (min 1µs), the memory can be accessed in read
mode again.
This program sequence is repeated throughout the memory until all data
is programmed.
NOTE:
Programming and erasing of FLASH locations cannot be performed by
code being executed from the same FLASH array that is being
programmed or erased. While these operations must be performed in
the order shown, other unrelated operations may occur between the
steps. Do not exceed tPROG maximum. See 24.14 FLASH Memory
Characteristics.
Data Sheet
70
MC68HC908LD64 — Rev. 3.0
FLASH Memory
Freescale Semiconductor
FLASH Memory
FLASH Program Operation
1
Algorithm for programming
a row (64 bytes) of FLASH memory
Set PGM bit
2
Write any data to any FLASH address
within the row address range desired
3
Wait for a time, tnvs
4
Set HVEN bit
5
Wait for a time, tpgs
For 13K-bytes array
6
Write even byte to OSD FLASH Even
High Byte Write Buffer at $0066.
For 47,616 bytes array
Write data to the FLASH address
to be programmed
7
Write odd byte to the FLASH address
to be programmed.
Wait for a time, tprog
Completed
programming
this row?
Y
N
NOTE:
The time between each FLASH address change (step 6 to step 6), or
the time between the last FLASH address programmed
to clearing PGM bit (step 6 to step 9)
must not exceed the maximum programming
time, tPROG max.
9
Clear PGM bit
10
Wait for a time, tnvh
11
Clear HVEN bit
12
Wait for a time, trcv
This row program algorithm assumes the row/s
to be programmed are initially erased.
End of Programming
Figure 4-5. FLASH Programming Flowchart
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
FLASH Memory
71
FLASH Memory
4.8 FLASH Block Protection
Due to the ability of the on-board charge pump to erase and program the
FLASH memory in the target application, provision is made for protecting
blocks of memory from unintentional erase or program operations due to
system malfunction. This protection is done by use of a FLASH Block
Protect Register for each array (FLBPR and FLBPR1). The block protect
register determines the range of the FLASH memory which is to be
protected. The range of the protected area starts from a location defined
by block protect register and ends at the bottom of the FLASH memory
array ($FFFF and $3FFF). When the memory is protected, the HVEN bit
cannot be set in either ERASE or PROGRAM operations.
4.8.1 FLASH Block Protect Registers
Each FLASH block protect register is implemented as an 7-bit I/O
register. The BPR bit content of the register determines the starting
location of the protected range within the FLASH memory.
This register controls the 47,616-byte array:
Address:
$FE08
Bit 7
6
5
4
3
2
1
BPR7
BPR6
BPR5
BPR4
BPR3
BPR2
BPR1
0
0
0
0
0
0
0
Read:
Bit 0
0
Write:
Reset:
0
Figure 4-6. 47,616-byte FLASH Block Protect Register (FLBPR)
This register controls the 13K-byte array:
Address:
$FE0B
Bit 7
6
5
4
3
2
1
BPR17
BPR16
BPR15
BPR14
BPR13
BPR12
BPR11
0
0
0
0
0
0
0
Read:
Bit 0
0
Write:
Reset:
0
Figure 4-7. 13K-byte FLASH Block Protect Register 1 (FLBPR1)
Data Sheet
72
MC68HC908LD64 — Rev. 3.0
FLASH Memory
Freescale Semiconductor
FLASH Memory
FLASH Block Protection
BPR[7:1] — FLASH Block Protect Bits
These seven bits represent bits [15:9] of a 16-bit memory address.
Bits [8:0] are logic 0s.
The resultant 16-bit address is used for specifying the start address
of the FLASH memory for block protection. The FLASH is protected
from this start address to the end of FLASH memory, at $FFFF.
BPR1[7:1] — FLASH Block Protect Bits
These seven bits represent bits [15:9] of a 16-bit memory address.
Bits [8:0] are logic 0s.
The resultant 16-bit address is used for specifying the start address
of the FLASH memory for block protection. The FLASH is protected
from this start address to the end of FLASH memory, at $3FFF.
16-bit memory address
Start address of FLASH block protect
0 0 0 0 0 0 0 0 0
BPR[7:1]
0
Figure 4-8. FLASH Block Protect Start Address
Examples of block protection for 47,616-byte FLASH memory array:
BPR[7:0]
FLASH Memory Protected Range
$40
The entire 47,616 bytes of FLASH memory is protected.
$42 (0100 0010)
$4200 (0100 0010 0000 0000) to $FFFF
$44 (0100 0100)
$4400 (0100 0100 0000 0000) to $FFFF
and so on...
$F8 (1111 1000)
$F800 (1111 1000 0000 0000) to $FFFF
$FA
$FFE0 to $FFFF (FLASH Vectors)
$FC
$FFE0 to $FFFF (FLASH Vectors)
$FE
$FFE0 to $FFFF (FLASH Vectors)
$00–3E
The entire 47,616 bytes FLASH memory is not protected.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
FLASH Memory
73
FLASH Memory
Examples of block protection for 13K-byte FLASH memory array:
BPR1[7:0]
FLASH Memory Protected Range
$0C
The entire 13K-byte FLASH memory is protected.
$0E (0000 1110)
$0E00 (0000 1110 0000 0000) to $3FFF
$10 (0001 0000)
$1000 (0001 0000 0000 0000) to $3FFF
and so on...
$38 (0011 1000)
$3800 (0011 1000 0000 0000) to $3FFF
$3A (0011 1010)
$3A00 (0011 1010 0000 0000) to $3FFF
$3C (0011 1100)
$3C00 (0011 1100 0000 0000) to $3FFF
$3E (0011 1110)
$3E00 (0011 1110 0000 0000) to $3FFF
$00–$0B or $40–$FE
The entire 13K-byte FLASH memory is not protected.
Data Sheet
74
MC68HC908LD64 — Rev. 3.0
FLASH Memory
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 5. Configuration Register (CONFIG)
5.1 Contents
5.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
5.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
5.4
Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
5.2 Introduction
This section describes the configuration register, CONFIG. The
configuration register enables or disables these options:
•
Stop mode recovery time (32 OSCXCLK cycles or 4096
OSCXCLK cycles)
•
COP timeout period (218 – 24 or 213 – 24 OSCXCLK cycles)
•
STOP instruction
•
Computer operating properly module (COP)
5.3 Functional Description
The configuration register is used in the initialization of various options.
The configuration register can be written once after each reset. All of the
configuration register bits are cleared during reset. Since the various
options affect the operation of the MCU, it is recommended that this
register be written immediately after reset. The configuration register is
located at $001F. The configuration register may be read at anytime.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Configuration Register (CONFIG)
75
Configuration Register (CONFIG)
5.4 Configuration Register
Address:
Read:
$001F
Bit 7
6
5
4
0
0
0
0
3
2
1
Bit 0
SSREC
COPRS
STOP
COPD
0
0
0
0
Write:
Reset:
0
0
0
0
= Unimplemented
Figure 5-1. Configuration Register (CONFIG)
SSREC — Short Stop Recovery Bit
SSREC enables the CPU to exit stop mode with a delay of 32
OSCXCLK cycles instead of a 4096 OSCXCLK cycle delay.
1 = Stop mode recovery after 32 OSCXCLK cycles
0 = Stop mode recovery after 4096 OSCXCLK cycles
NOTE:
Exiting stop mode by pulling reset will result in the long stop recovery.
If using an external crystal oscillator, do not set the SSREC bit.
COPRS — COP Rate Select Bit
COPRS selects the COP timeout period. Reset clears COPRS. (See
Section 22. Computer Operating Properly (COP).)
1 = COP timeout period = 213 – 24 OSCXCLK cycles
0 = COP timeout period = 218 – 24 OSCXCLK cycles
STOP — STOP Instruction Enable Bit
STOP enables the STOP instruction.
1 = STOP instruction enabled
0 = STOP instruction treated as illegal opcode
COPD — COP Disable Bit
COPD disables the COP module. (See Section 22. Computer
Operating Properly (COP).)
1 = COP module disabled
0 = COP module enabled
Data Sheet
76
MC68HC908LD64 — Rev. 3.0
Configuration Register (CONFIG)
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 6. Central Processor Unit (CPU)
6.1 Contents
6.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
6.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
6.4
CPU Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
6.4.1
Accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
6.4.2
Index Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
6.4.3
Stack Pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
6.4.4
Program Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
6.4.5
Condition Code Register . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
6.5
Arithmetic/Logic Unit (ALU) . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
6.6
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
6.6.1
Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
6.6.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
6.7
CPU During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . 85
6.8
Instruction Set Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
6.9
Opcode Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Central Processor Unit (CPU)
77
Central Processor Unit (CPU)
6.2 Introduction
The M68HC08 CPU (central processor unit) is an enhanced and fully
object-code-compatible version of the M68HC05 CPU. The CPU08
Reference Manual (Freescale document order number CPU08RM/AD)
contains a description of the CPU instruction set, addressing modes,
and architecture.
6.3 Features
Feature of the CPU include:
•
Object code fully upward-compatible with M68HC05 Family
•
16-bit stack pointer with stack manipulation instructions
•
16-Bit index register with X-register manipulation instructions
•
6-MHz CPU internal bus frequency
•
64-Kbyte program/data memory space
•
16 addressing modes
•
Memory-to-memory data moves without using accumulator
•
Fast 8-bit by 8-bit multiply and 16-bit by 8-bit divide instructions
•
Enhanced binary-coded decimal (BCD) data handling
•
Modular architecture with expandable internal bus definition for
extension of addressing range beyond 64-Kbytes
•
Low-power stop and wait modes
Data Sheet
78
MC68HC908LD64 — Rev. 3.0
Central Processor Unit (CPU)
Freescale Semiconductor
Central Processor Unit (CPU)
CPU Registers
6.4 CPU Registers
Figure 6-1 shows the five CPU registers. CPU registers are not part of
the memory map.
0
7
ACCUMULATOR (A)
0
15
H
X
INDEX REGISTER (H:X)
15
0
STACK POINTER (SP)
15
0
PROGRAM COUNTER (PC)
7
0
V 1 1 H I N Z C
CONDITION CODE REGISTER (CCR)
CARRY/BORROW FLAG
ZERO FLAG
NEGATIVE FLAG
INTERRUPT MASK
HALF-CARRY FLAG
TWO’S COMPLEMENT OVERFLOW FLAG
Figure 6-1. CPU Registers
6.4.1 Accumulator
The accumulator is a general-purpose 8-bit register. The CPU uses the
accumulator to hold operands and the results of arithmetic/logic
operations.
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Write:
Reset:
Unaffected by reset
Figure 6-2. Accumulator (A)
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Central Processor Unit (CPU)
79
Central Processor Unit (CPU)
6.4.2 Index Register
The 16-bit index register allows indexed addressing of a 64K-byte
memory space. H is the upper byte of the index register, and X is the
lower byte. H:X is the concatenated 16-bit index register.
In the indexed addressing modes, the CPU uses the contents of the
index register to determine the conditional address of the operand.
The index register can serve also as a temporary data storage location.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Bit
0
0
0
0
0
0
0
0
0
X
X
X
X
X
X
X
X
Read:
Write:
Reset:
X = Indeterminate
Figure 6-3. Index Register (H:X)
6.4.3 Stack Pointer
The stack pointer is a 16-bit register that contains the address of the next
location on the stack. During a reset, the stack pointer is preset to
$00FF. The reset stack pointer (RSP) instruction sets the least
significant byte to $FF and does not affect the most significant byte. The
stack pointer decrements as data is pushed onto the stack and
increments as data is pulled from the stack.
In the stack pointer 8-bit offset and 16-bit offset addressing modes, the
stack pointer can function as an index register to access data on the
stack. The CPU uses the contents of the stack pointer to determine the
conditional address of the operand.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Bit
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
Read:
Write:
Reset:
Figure 6-4. Stack Pointer (SP)
Data Sheet
80
MC68HC908LD64 — Rev. 3.0
Central Processor Unit (CPU)
Freescale Semiconductor
Central Processor Unit (CPU)
CPU Registers
NOTE:
The location of the stack is arbitrary and may be relocated anywhere in
RAM. Moving the SP out of page 0 ($0000 to $00FF) frees direct
address (page 0) space. For correct operation, the stack pointer must
point only to RAM locations.
6.4.4 Program Counter
The program counter is a 16-bit register that contains the address of the
next instruction or operand to be fetched.
Normally, the program counter automatically increments to the next
sequential memory location every time an instruction or operand is
fetched. Jump, branch, and interrupt operations load the program
counter with an address other than that of the next sequential location.
During reset, the program counter is loaded with the reset vector
address located at $FFFE and $FFFF. The vector address is the
address of the first instruction to be executed after exiting the reset state.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Bit
0
Read:
Write:
Reset:
Loaded with Vector from $FFFE and $FFFF
Figure 6-5. Program Counter (PC)
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Central Processor Unit (CPU)
81
Central Processor Unit (CPU)
6.4.5 Condition Code Register
The 8-bit condition code register contains the interrupt mask and five
flags that indicate the results of the instruction just executed. Bits 6 and
5 are set permanently to logic 1. The following paragraphs describe the
functions of the condition code register.
Bit 7
6
5
4
3
2
1
Bit 0
V
1
1
H
I
N
Z
C
X
1
1
X
1
X
X
X
Read:
Write:
Reset:
X = Indeterminate
Figure 6-6. Condition Code Register (CCR)
V — Overflow Flag
The CPU sets the overflow flag when a two's complement overflow
occurs. The signed branch instructions BGT, BGE, BLE, and BLT use
the overflow flag.
1 = Overflow
0 = No overflow
H — Half-Carry Flag
The CPU sets the half-carry flag when a carry occurs between
accumulator bits 3 and 4 during an add-without-carry (ADD) or addwith-carry (ADC) operation. The half-carry flag is required for binarycoded decimal (BCD) arithmetic operations. The DAA instruction
uses the states of the H and C flags to determine the appropriate
correction factor.
1 = Carry between bits 3 and 4
0 = No carry between bits 3 and 4
Data Sheet
82
MC68HC908LD64 — Rev. 3.0
Central Processor Unit (CPU)
Freescale Semiconductor
Central Processor Unit (CPU)
CPU Registers
I — Interrupt Mask
When the interrupt mask is set, all maskable CPU interrupts are
disabled. CPU interrupts are enabled when the interrupt mask is
cleared. When a CPU interrupt occurs, the interrupt mask is set
automatically after the CPU registers are saved on the stack, but
before the interrupt vector is fetched.
1 = Interrupts disabled
0 = Interrupts enabled
NOTE:
To maintain M6805 Family compatibility, the upper byte of the index
register (H) is not stacked automatically. If the interrupt service routine
modifies H, then the user must stack and unstack H using the PSHH and
PULH instructions.
After the I bit is cleared, the highest-priority interrupt request is
serviced first.
A return-from-interrupt (RTI) instruction pulls the CPU registers from
the stack and restores the interrupt mask from the stack. After any
reset, the interrupt mask is set and can be cleared only by the clear
interrupt mask software instruction (CLI).
N — Negative Flag
The CPU sets the negative flag when an arithmetic operation, logic
operation, or data manipulation produces a negative result, setting
bit 7 of the result.
1 = Negative result
0 = Non-negative result
Z — Zero Flag
The CPU sets the zero flag when an arithmetic operation, logic
operation, or data manipulation produces a result of $00.
1 = Zero result
0 = Non-zero result
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Central Processor Unit (CPU)
83
Central Processor Unit (CPU)
C — Carry/Borrow Flag
The CPU sets the carry/borrow flag when an addition operation
produces a carry out of bit 7 of the accumulator or when a subtraction
operation requires a borrow. Some instructions — such as bit test and
branch, shift, and rotate — also clear or set the carry/borrow flag.
1 = Carry out of bit 7
0 = No carry out of bit 7
6.5 Arithmetic/Logic Unit (ALU)
The ALU performs the arithmetic and logic operations defined by the
instruction set.
Refer to the CPU08 Reference Manual (Freescale document order
number CPU08RM/AD) for a description of the instructions and
addressing modes and more detail about the architecture of the CPU.
6.6 Low-Power Modes
The WAIT and STOP instructions put the MCU in low power-consumption
standby modes.
6.6.1 Wait Mode
The WAIT instruction:
•
Clears the interrupt mask (I bit) in the condition code register,
enabling interrupts. After exit from wait mode by interrupt, the I bit
remains clear. After exit by reset, the I bit is set.
•
Disables the CPU clock.
Data Sheet
84
MC68HC908LD64 — Rev. 3.0
Central Processor Unit (CPU)
Freescale Semiconductor
Central Processor Unit (CPU)
CPU During Break Interrupts
6.6.2 Stop Mode
The STOP instruction:
•
Clears the interrupt mask (I bit) in the condition code register,
enabling external interrupts. After exit from stop mode by external
interrupt, the I bit remains clear. After exit by reset, the I bit is set.
•
Disables the CPU clock.
After exiting stop mode, the CPU clock begins running after the oscillator
stabilization delay.
6.7 CPU During Break Interrupts
If the break module is enabled, a break interrupt causes the CPU to
execute the software interrupt instruction (SWI) at the completion of the
current CPU instruction. (See Section 23. Break Module (BRK).) The
program counter vectors to $FFFC–$FFFD ($FEFC–$FEFD in monitor
mode).
A return-from-interrupt instruction (RTI) in the break routine ends the
break interrupt and returns the MCU to normal operation if the break
interrupt has been deasserted.
6.8 Instruction Set Summary
Table 6-1 provides a summary of the M68HC08 instruction set.
6.9 Opcode Map
The opcode map is provided in Table 6-2.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Central Processor Unit (CPU)
85
Central Processor Unit (CPU)
V H I N Z C
ADC #opr
ADC opr
ADC opr
ADC opr,X
ADC opr,X
ADC ,X
ADC opr,SP
ADC opr,SP
A ← (A) + (M) + (C)
Add with Carry
IMM
DIR
EXT
IX2
R R – R R R
IX1
IX
SP1
SP2
A9
B9
C9
D9
E9
F9
9EE9
9ED9
ii
dd
hh ll
ee ff
ff
IMM
DIR
EXT
IX2
R R – R R R
IX1
IX
SP1
SP2
AB
BB
CB
DB
EB
FB
9EEB
9EDB
ii
dd
hh ll
ee ff
ff
ff
ee ff
A7
ii
2
– – – – – – IMM
AF
ii
2
IMM
DIR
EXT
IX2
0 – – R R –
IX1
IX
SP1
SP2
A4
B4
C4
D4
E4
F4
9EE4
9ED4
ii
dd
hh ll
ee ff
ff
2
3
4
4
3
2
4
5
DIR
INH
INH
R – – R R R
IX1
IX
SP1
38
48
58
68
78
9E68
dd
DIR
INH
INH
R – – R R R
IX1
IX
SP1
37
47
57
67
77
9E67
dd
ff
4
1
1
4
3
5
– – – – – – REL
24
rr
3
DIR (b0)
DIR (b1)
DIR (b2)
DIR (b3)
– – – – – –
DIR (b4)
DIR (b5)
DIR (b6)
DIR (b7)
11
13
15
17
19
1B
1D
1F
dd
dd
dd
dd
dd
dd
dd
dd
4
4
4
4
4
4
4
4
Add without Carry
AIS #opr
Add Immediate Value (Signed) to SP
SP ← (SP) + (16 « M)
– – – – – – IMM
AIX #opr
Add Immediate Value (Signed) to H:X
H:X ← (H:X) + (16 « M)
A ← (A) & (M)
AND #opr
AND opr
AND opr
AND opr,X
AND opr,X
AND ,X
AND opr,SP
AND opr,SP
ASL opr
ASLA
ASLX
ASL opr,X
ASL ,X
ASL opr,SP
Logical AND
Arithmetic Shift Left
(Same as LSL)
ASR opr
ASRA
ASRX
ASR opr,X
ASR opr,X
ASR opr,SP
Arithmetic Shift Right
BCC rel
Branch if Carry Bit Clear
BCLR n, opr
C
0
b7
b0
C
b7
Clear Bit n in M
b0
PC ← (PC) + 2 + rel ? (C) = 0
Mn ← 0
Data Sheet
86
2
3
4
4
3
2
4
5
2
3
4
4
3
2
4
5
ADD #opr
ADD opr
ADD opr
ADD opr,X
ADD opr,X
ADD ,X
ADD opr,SP
ADD opr,SP
A ← (A) + (M)
ff
ee ff
Cycles
Effect on
CCR
Description
Operand
Operation
Opcode
Source
Form
Address
Mode
Table 6-1. Instruction Set Summary (Sheet 1 of 8)
ff
ee ff
ff
ff
ff
4
1
1
4
3
5
MC68HC908LD64 — Rev. 3.0
Central Processor Unit (CPU)
Freescale Semiconductor
Central Processor Unit (CPU)
Opcode Map
Effect on
CCR
V H I N Z C
Cycles
Description
Operand
Operation
Opcode
Source
Form
Address
Mode
Table 6-1. Instruction Set Summary (Sheet 2 of 8)
BCS rel
Branch if Carry Bit Set (Same as BLO)
PC ← (PC) + 2 + rel ? (C) = 1
– – – – – – REL
25
rr
3
BEQ rel
Branch if Equal
PC ← (PC) + 2 + rel ? (Z) = 1
– – – – – – REL
27
rr
3
BGE opr
Branch if Greater Than or Equal To
(Signed Operands)
PC ← (PC) + 2 + rel ? (N ⊕ V) = 0
– – – – – – REL
90
rr
3
BGT opr
Branch if Greater Than (Signed
Operands)
PC ← (PC) + 2 + rel ? (Z) | (N ⊕ V) = 0 – – – – – – REL
92
rr
3
BHCC rel
Branch if Half Carry Bit Clear
PC ← (PC) + 2 + rel ? (H) = 0
– – – – – – REL
28
rr
3
BHCS rel
Branch if Half Carry Bit Set
PC ← (PC) + 2 + rel ? (H) = 1
– – – – – – REL
29
rr
3
BHI rel
Branch if Higher
PC ← (PC) + 2 + rel ? (C) | (Z) = 0
– – – – – – REL
22
rr
3
BHS rel
Branch if Higher or Same
(Same as BCC)
PC ← (PC) + 2 + rel ? (C) = 0
– – – – – – REL
24
rr
3
BIH rel
Branch if IRQ Pin High
PC ← (PC) + 2 + rel ? IRQ = 1
– – – – – – REL
2F
rr
3
BIL rel
Branch if IRQ Pin Low
PC ← (PC) + 2 + rel ? IRQ = 0
– – – – – – REL
2E
rr
3
(A) & (M)
IMM
DIR
EXT
IX2
0 – – R R –
IX1
IX
SP1
SP2
A5
B5
C5
D5
E5
F5
9EE5
9ED5
ii
dd
hh ll
ee ff
ff
ff
ee ff
2
3
4
4
3
2
4
5
BIT #opr
BIT opr
BIT opr
BIT opr,X
BIT opr,X
BIT ,X
BIT opr,SP
BIT opr,SP
Bit Test
BLE opr
Branch if Less Than or Equal To
(Signed Operands)
PC ← (PC) + 2 + rel ? (Z) | (N ⊕ V) = 1
– – – – – – REL
93
rr
3
BLO rel
Branch if Lower (Same as BCS)
PC ← (PC) + 2 + rel ? (C) = 1
– – – – – – REL
25
rr
3
BLS rel
Branch if Lower or Same
PC ← (PC) + 2 + rel ? (C) | (Z) = 1
– – – – – – REL
23
rr
3
BLT opr
Branch if Less Than (Signed Operands)
PC ← (PC) + 2 + rel ? (N ⊕ V) =1
– – – – – – REL
91
rr
3
BMC rel
Branch if Interrupt Mask Clear
PC ← (PC) + 2 + rel ? (I) = 0
– – – – – – REL
2C
rr
3
BMI rel
Branch if Minus
PC ← (PC) + 2 + rel ? (N) = 1
– – – – – – REL
2B
rr
3
BMS rel
Branch if Interrupt Mask Set
PC ← (PC) + 2 + rel ? (I) = 1
– – – – – – REL
2D
rr
3
BNE rel
Branch if Not Equal
PC ← (PC) + 2 + rel ? (Z) = 0
– – – – – – REL
26
rr
3
BPL rel
Branch if Plus
PC ← (PC) + 2 + rel ? (N) = 0
– – – – – – REL
2A
rr
3
BRA rel
Branch Always
PC ← (PC) + 2 + rel
– – – – – – REL
20
rr
3
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Central Processor Unit (CPU)
87
Central Processor Unit (CPU)
Table 6-1. Instruction Set Summary (Sheet 3 of 8)
Operand
Cycles
Effect on
CCR
Opcode
Operation
DIR (b0)
DIR (b1)
DIR (b2)
DIR (b3)
– – – – – R
DIR (b4)
DIR (b5)
DIR (b6)
DIR (b7)
01
03
05
07
09
0B
0D
0F
dd rr
dd rr
dd rr
dd rr
dd rr
dd rr
dd rr
dd rr
5
5
5
5
5
5
5
5
– – – – – – REL
21
rr
3
PC ← (PC) + 3 + rel ? (Mn) = 1
DIR (b0)
DIR (b1)
DIR (b2)
DIR (b3)
– – – – – R
DIR (b4)
DIR (b5)
DIR (b6)
DIR (b7)
00
02
04
06
08
0A
0C
0E
dd rr
dd rr
dd rr
dd rr
dd rr
dd rr
dd rr
dd rr
5
5
5
5
5
5
5
5
Mn ← 1
DIR (b0)
DIR (b1)
DIR (b2)
DIR (b3)
– – – – – –
DIR (b4)
DIR (b5)
DIR (b6)
DIR (b7)
10
12
14
16
18
1A
1C
1E
dd
dd
dd
dd
dd
dd
dd
dd
4
4
4
4
4
4
4
4
– – – – – – REL
AD
rr
4
dd rr
ii rr
ii rr
ff rr
rr
ff rr
5
4
4
5
4
6
Description
V H I N Z C
BRCLR n,opr,rel Branch if Bit n in M Clear
BRN rel
Branch Never
BRSET n,opr,rel Branch if Bit n in M Set
BSET n,opr
Set Bit n in M
BSR rel
Branch to Subroutine
CBEQ opr,rel
CBEQA #opr,rel
CBEQX #opr,rel
Compare and Branch if Equal
CBEQ opr,X+,rel
CBEQ X+,rel
CBEQ opr,SP,rel
PC ← (PC) + 3 + rel ? (Mn) = 0
PC ← (PC) + 2
PC ← (PC) + 2; push (PCL)
SP ← (SP) – 1; push (PCH)
SP ← (SP) – 1
PC ← (PC) + rel
Address
Mode
Source
Form
DIR
PC ← (PC) + 3 + rel ? (A) – (M) = $00
IMM
PC ← (PC) + 3 + rel ? (A) – (M) = $00
IMM
PC ← (PC) + 3 + rel ? (X) – (M) = $00
– – – – – –
IX1+
PC ← (PC) + 3 + rel ? (A) – (M) = $00
IX+
PC ← (PC) + 2 + rel ? (A) – (M) = $00
SP1
PC ← (PC) + 4 + rel ? (A) – (M) = $00
31
41
51
61
71
9E61
CLC
Clear Carry Bit
C←0
– – – – – 0 INH
98
1
CLI
Clear Interrupt Mask
I←0
– – 0 – – – INH
9A
2
M ← $00
A ← $00
X ← $00
H ← $00
M ← $00
M ← $00
M ← $00
DIR
INH
INH
0 – – 0 1 – INH
IX1
IX
SP1
3F
4F
5F
8C
6F
7F
9E6F
CLR opr
CLRA
CLRX
CLRH
CLR opr,X
CLR ,X
CLR opr,SP
Clear
Data Sheet
88
dd
ff
ff
3
1
1
1
3
2
4
MC68HC908LD64 — Rev. 3.0
Central Processor Unit (CPU)
Freescale Semiconductor
Central Processor Unit (CPU)
Opcode Map
Effect on
CCR
V H I N Z C
CMP #opr
CMP opr
CMP opr
CMP opr,X
CMP opr,X
CMP ,X
CMP opr,SP
CMP opr,SP
Compare A with M
(A) – (M)
COM opr
COMA
COMX
COM opr,X
COM ,X
COM opr,SP
Complement (One’s Complement)
CPHX #opr
CPHX opr
Compare H:X with M
CPX #opr
CPX opr
CPX opr
CPX ,X
CPX opr,X
CPX opr,X
CPX opr,SP
CPX opr,SP
Compare X with M
DAA
Decimal Adjust A
M ← (M) = $FF – (M)
A ← (A) = $FF – (M)
X ← (X) = $FF – (M)
M ← (M) = $FF – (M)
M ← (M) = $FF – (M)
M ← (M) = $FF – (M)
IMM
DIR
EXT
IX2
R – – R R R
IX1
IX
SP1
SP2
A1
B1
C1
D1
E1
F1
9EE1
9ED1
ii
dd
hh ll
ee ff
ff
DIR
INH
INH
0 – – R R 1
IX1
IX
SP1
33
43
53
63
73
9E63
dd
ff
ee ff
Cycles
Description
Operand
Operation
Opcode
Source
Form
Address
Mode
Table 6-1. Instruction Set Summary (Sheet 4 of 8)
2
3
4
4
3
2
4
5
ff
4
1
1
4
3
5
65
75
ii ii+1
dd
3
4
IMM
DIR
EXT
IX2
R – – R R R
IX1
IX
SP1
SP2
A3
B3
C3
D3
E3
F3
9EE3
9ED3
ii
dd
hh ll
ee ff
ff
2
3
4
4
3
2
4
5
U – – R R R INH
72
PC ← (PC) + 3 + rel ? (result) ≠ 0
PC ← (PC) + 2 + rel ? (result) ≠ 0
PC ← (PC) + 2 + rel ? (result) ≠ 0
PC ← (PC) + 3 + rel ? (result) ≠ 0
PC ← (PC) + 2 + rel ? (result) ≠ 0
PC ← (PC) + 4 + rel ? (result) ≠ 0
DIR
INH
– – – – – – INH
IX1
IX
SP1
3B
4B
5B
6B
7B
9E6B
dd rr
rr
rr
ff rr
rr
ff rr
5
3
3
5
4
6
M ← (M) – 1
A ← (A) – 1
X ← (X) – 1
M ← (M) – 1
M ← (M) – 1
M ← (M) – 1
DIR
INH
INH
R – – R R –
IX1
IX
SP1
3A
4A
5A
6A
7A
9E6A
dd
4
1
1
4
3
5
A ← (H:A)/(X)
H ← Remainder
– – – – R R INH
52
A ← (A ⊕ M)
IMM
DIR
EXT
IX2
0 – – R R –
IX1
IX
SP1
SP2
A8
B8
C8
D8
E8
F8
9EE8
9ED8
(H:X) – (M:M + 1)
(X) – (M)
(A)10
R – – R R R
IMM
DIR
ff
ff
ee ff
2
A ← (A) – 1 or M ← (M) – 1 or X ← (X) – 1
DBNZ opr,rel
DBNZA rel
Decrement and Branch if Not Zero
DBNZX rel
DBNZ opr,X,rel
DBNZ X,rel
DBNZ opr,SP,rel
DEC opr
DECA
DECX
DEC opr,X
DEC ,X
DEC opr,SP
Decrement
DIV
Divide
EOR #opr
EOR opr
EOR opr
EOR opr,X
EOR opr,X
EOR ,X
EOR opr,SP
EOR opr,SP
Exclusive OR M with A
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
ff
ff
7
ii
dd
hh ll
ee ff
ff
ff
ee ff
2
3
4
4
3
2
4
5
Data Sheet
Central Processor Unit (CPU)
89
Central Processor Unit (CPU)
V H I N Z C
INC opr
INCA
INCX
INC opr,X
INC ,X
INC opr,SP
JMP opr
JMP opr
JMP opr,X
JMP opr,X
JMP ,X
JSR opr
JSR opr
JSR opr,X
JSR opr,X
JSR ,X
Load A from M
LDHX #opr
LDHX opr
Load H:X from M
LSL opr
LSLA
LSLX
LSL opr,X
LSL ,X
LSL opr,SP
LSR opr
LSRA
LSRX
LSR opr,X
LSR ,X
LSR opr,SP
DIR
INH
INH
R – – R R –
IX1
IX
SP1
3C
4C
5C
6C
7C
9E6C
PC ← Jump Address
DIR
EXT
– – – – – – IX2
IX1
IX
BC
CC
DC
EC
FC
dd
hh ll
ee ff
ff
2
3
4
3
2
PC ← (PC) + n (n = 1, 2, or 3)
Push (PCL); SP ← (SP) – 1
Push (PCH); SP ← (SP) – 1
PC ← Unconditional Address
DIR
EXT
– – – – – – IX2
IX1
IX
BD
CD
DD
ED
FD
dd
hh ll
ee ff
ff
4
5
6
5
4
A ← (M)
IMM
DIR
EXT
IX2
0 – – R R –
IX1
IX
SP1
SP2
A6
B6
C6
D6
E6
F6
9EE6
9ED6
ii
dd
hh ll
ee ff
ff
ff
ee ff
2
3
4
4
3
2
4
5
ii jj
dd
3
4
2
3
4
4
3
2
4
5
Jump
LDA #opr
LDA opr
LDA opr
LDA opr,X
LDA opr,X
LDA ,X
LDA opr,SP
LDA opr,SP
LDX #opr
LDX opr
LDX opr
LDX opr,X
LDX opr,X
LDX ,X
LDX opr,SP
LDX opr,SP
M ← (M) + 1
A ← (A) + 1
X ← (X) + 1
M ← (M) + 1
M ← (M) + 1
M ← (M) + 1
Increment
Jump to Subroutine
H:X ← (M:M + 1)
Logical Shift Right
0 – – R R –
X ← (M)
Load X from M
Logical Shift Left
(Same as ASL)
C
0
b7
b0
0
C
b7
b0
Data Sheet
90
Cycles
Effect on
CCR
Description
Operand
Operation
Opcode
Source
Form
Address
Mode
Table 6-1. Instruction Set Summary (Sheet 5 of 8)
IMM
DIR
45
55
dd
ff
ff
IMM
DIR
EXT
IX2
0 – – R R –
IX1
IX
SP1
SP2
AE
BE
CE
DE
EE
FE
9EEE
9EDE
ii
dd
hh ll
ee ff
ff
DIR
INH
INH
R – – R R R
IX1
IX
SP1
38
48
58
68
78
9E68
dd
DIR
INH
INH
R – – 0 R R
IX1
IX
SP1
34
44
54
64
74
9E64
dd
ff
ee ff
ff
ff
ff
ff
4
1
1
4
3
5
4
1
1
4
3
5
4
1
1
4
3
5
MC68HC908LD64 — Rev. 3.0
Central Processor Unit (CPU)
Freescale Semiconductor
Central Processor Unit (CPU)
Opcode Map
Table 6-1. Instruction Set Summary (Sheet 6 of 8)
Opcode
Operand
Cycles
Effect on
CCR
DD
DIX+
0 – – R R –
IMD
IX+D
4E
5E
6E
7E
dd dd
dd
ii dd
dd
5
4
4
4
X:A ← (X) × (A)
– 0 – – – 0 INH
42
M ← –(M) = $00 – (M)
A ← –(A) = $00 – (A)
X ← –(X) = $00 – (X)
M ← –(M) = $00 – (M)
M ← –(M) = $00 – (M)
DIR
INH
INH
R – – R R R
IX1
IX
SP1
30
40
50
60
70
9E60
Operation
Description
V H I N Z C
MOV opr,opr
MOV opr,X+
MOV #opr,opr
MOV X+,opr
Move
MUL
Unsigned multiply
(M)Destination ← (M)Source
H:X ← (H:X) + 1 (IX+D, DIX+)
Address
Mode
Source
Form
5
dd
4
1
1
4
3
5
NEG opr
NEGA
NEGX
NEG opr,X
NEG ,X
NEG opr,SP
Negate (Two’s Complement)
NOP
No Operation
None
– – – – – – INH
9D
1
NSA
Nibble Swap A
A ← (A[3:0]:A[7:4])
– – – – – – INH
62
3
A ← (A) | (M)
IMM
DIR
EXT
IX2
0 – – R R –
IX1
IX
SP1
SP2
AA
BA
CA
DA
EA
FA
9EEA
9EDA
ff
ff
ORA #opr
ORA opr
ORA opr
ORA opr,X
ORA opr,X
ORA ,X
ORA opr,SP
ORA opr,SP
Inclusive OR A and M
PSHA
Push A onto Stack
Push (A); SP ← (SP) – 1
– – – – – – INH
87
2
PSHH
Push H onto Stack
Push (H); SP ← (SP) – 1
– – – – – – INH
8B
2
PSHX
Push X onto Stack
Push (X); SP ← (SP) – 1
– – – – – – INH
89
2
PULA
Pull A from Stack
SP ← (SP + 1); Pull (A)
– – – – – – INH
86
2
PULH
Pull H from Stack
SP ← (SP + 1); Pull (H)
– – – – – – INH
8A
2
PULX
Pull X from Stack
SP ← (SP + 1); Pull (X)
– – – – – – INH
88
2
39
49
59
69
79
9E69
dd
C
DIR
INH
INH
R – – R R R
IX1
IX
SP1
DIR
INH
INH
R – – R R R
IX1
IX
SP1
36
46
56
66
76
9E66
dd
– – – – – – INH
9C
ROL opr
ROLA
ROLX
ROL opr,X
ROL ,X
ROL opr,SP
Rotate Left through Carry
b7
ROR opr
RORA
RORX
ROR opr,X
ROR ,X
ROR opr,SP
Rotate Right through Carry
RSP
Reset Stack Pointer
b0
C
b7
b0
SP ← $FF
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
ii
dd
hh ll
ee ff
ff
ff
ee ff
ff
ff
ff
ff
2
3
4
4
3
2
4
5
4
1
1
4
3
5
4
1
1
4
3
5
1
Data Sheet
Central Processor Unit (CPU)
91
Central Processor Unit (CPU)
Effect on
CCR
V H I N Z C
RTI
Return from Interrupt
RTS
Return from Subroutine
Cycles
Description
Operand
Operation
Opcode
Source
Form
Address
Mode
Table 6-1. Instruction Set Summary (Sheet 7 of 8)
SP ← (SP) + 1; Pull (CCR)
SP ← (SP) + 1; Pull (A)
SP ← (SP) + 1; Pull (X)
SP ← (SP) + 1; Pull (PCH)
SP ← (SP) + 1; Pull (PCL)
R R R R R R INH
80
7
SP ← SP + 1; Pull (PCH)
SP ← SP + 1; Pull (PCL)
– – – – – – INH
81
4
A ← (A) – (M) – (C)
IMM
DIR
EXT
IX2
R – – R R R
IX1
IX
SP1
SP2
A2
B2
C2
D2
E2
F2
9EE2
9ED2
ii
dd
hh ll
ee ff
ff
2
3
4
4
3
2
4
5
SBC #opr
SBC opr
SBC opr
SBC opr,X
SBC opr,X
SBC ,X
SBC opr,SP
SBC opr,SP
Subtract with Carry
SEC
Set Carry Bit
C←1
– – – – – 1 INH
99
1
SEI
Set Interrupt Mask
I←1
– – 1 – – – INH
9B
2
M ← (A)
DIR
EXT
IX2
0 – – R R – IX1
IX
SP1
SP2
B7
C7
D7
E7
F7
9EE7
9ED7
(M:M + 1) ← (H:X)
0 – – R R – DIR
35
I ← 0; Stop Oscillator
– – 0 – – – INH
8E
M ← (X)
DIR
EXT
IX2
0 – – R R – IX1
IX
SP1
SP2
BF
CF
DF
EF
FF
9EEF
9EDF
dd
hh ll
ee ff
ff
IMM
DIR
EXT
IX2
R – – R R R
IX1
IX
SP1
SP2
A0
B0
C0
D0
E0
F0
9EE0
9ED0
ii
dd
hh ll
ee ff
ff
STA opr
STA opr
STA opr,X
STA opr,X
STA ,X
STA opr,SP
STA opr,SP
Store A in M
STHX opr
Store H:X in M
STOP
Enable IRQ Pin; Stop Oscillator
STX opr
STX opr
STX opr,X
STX opr,X
STX ,X
STX opr,SP
STX opr,SP
SUB #opr
SUB opr
SUB opr
SUB opr,X
SUB opr,X
SUB ,X
SUB opr,SP
SUB opr,SP
Store X in M
Subtract
A ← (A) – (M)
Data Sheet
92
ff
ee ff
ff
ee ff
3
4
4
3
2
4
5
dd
4
dd
hh ll
ee ff
ff
1
ff
ee ff
ff
ee ff
3
4
4
3
2
4
5
2
3
4
4
3
2
4
5
MC68HC908LD64 — Rev. 3.0
Central Processor Unit (CPU)
Freescale Semiconductor
Central Processor Unit (CPU)
Opcode Map
V H I N Z C
Cycles
Effect on
CCR
Description
Operand
Operation
Opcode
Source
Form
Address
Mode
Table 6-1. Instruction Set Summary (Sheet 8 of 8)
SWI
Software Interrupt
PC ← (PC) + 1; Push (PCL)
SP ← (SP) – 1; Push (PCH)
SP ← (SP) – 1; Push (X)
SP ← (SP) – 1; Push (A)
SP ← (SP) – 1; Push (CCR)
SP ← (SP) – 1; I ← 1
PCH ← Interrupt Vector High Byte
PCL ← Interrupt Vector Low Byte
TAP
Transfer A to CCR
CCR ← (A)
R R R R R R INH
84
2
TAX
Transfer A to X
X ← (A)
– – – – – – INH
97
1
TPA
Transfer CCR to A
A ← (CCR)
– – – – – – INH
85
1
(A) – $00 or (X) – $00 or (M) – $00
DIR
INH
INH
0 – – R R –
IX1
IX
SP1
3D
4D
5D
6D
7D
9E6D
H:X ← (SP) + 1
– – – – – – INH
95
2
A ← (X)
– – – – – – INH
9F
1
(SP) ← (H:X) – 1
– – – – – – INH
94
2
TST opr
TSTA
TSTX
TST opr,X
TST ,X
TST opr,SP
Test for Negative or Zero
TSX
Transfer SP to H:X
TXA
Transfer X to A
TXS
Transfer H:X to SP
A
C
CCR
dd
dd rr
DD
DIR
DIX+
ee ff
EXT
ff
H
H
hh ll
I
ii
IMD
IMM
INH
IX
IX+
IX+D
IX1
IX1+
IX2
M
N
Accumulator
Carry/borrow bit
Condition code register
Direct address of operand
Direct address of operand and relative offset of branch instruction
Direct to direct addressing mode
Direct addressing mode
Direct to indexed with post increment addressing mode
High and low bytes of offset in indexed, 16-bit offset addressing
Extended addressing mode
Offset byte in indexed, 8-bit offset addressing
Half-carry bit
Index register high byte
High and low bytes of operand address in extended addressing
Interrupt mask
Immediate operand byte
Immediate source to direct destination addressing mode
Immediate addressing mode
Inherent addressing mode
Indexed, no offset addressing mode
Indexed, no offset, post increment addressing mode
Indexed with post increment to direct addressing mode
Indexed, 8-bit offset addressing mode
Indexed, 8-bit offset, post increment addressing mode
Indexed, 16-bit offset addressing mode
Memory location
Negative bit
n
opr
PC
PCH
PCL
REL
rel
rr
SP1
SP2
SP
U
V
X
Z
&
|
⊕
()
–( )
#
«
←
?
:
R
—
83
9
dd
ff
ff
3
1
1
3
2
4
Any bit
Operand (one or two bytes)
Program counter
Program counter high byte
Program counter low byte
Relative addressing mode
Relative program counter offset byte
Relative program counter offset byte
Stack pointer, 8-bit offset addressing mode
Stack pointer 16-bit offset addressing mode
Stack pointer
Undefined
Overflow bit
Index register low byte
Zero bit
Logical AND
Logical OR
Logical EXCLUSIVE OR
Contents of
Negation (two’s complement)
Immediate value
Sign extend
Loaded with
If
Concatenated with
Set or cleared
Not affected
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
– – 1 – – – INH
Data Sheet
Central Processor Unit (CPU)
93
MSB
Branch
REL
DIR
INH
3
4
0
1
2
5
BRSET0
3 DIR
5
BRCLR0
3 DIR
5
BRSET1
3 DIR
5
BRCLR1
3 DIR
5
BRSET2
3 DIR
5
BRCLR2
3 DIR
5
BRSET3
3 DIR
5
BRCLR3
3 DIR
5
BRSET4
3 DIR
5
BRCLR4
3 DIR
5
BRSET5
3 DIR
5
BRCLR5
3 DIR
5
BRSET6
3 DIR
5
BRCLR6
3 DIR
5
BRSET7
3 DIR
5
BRCLR7
3 DIR
4
BSET0
2 DIR
4
BCLR0
2 DIR
4
BSET1
2 DIR
4
BCLR1
2 DIR
4
BSET2
2 DIR
4
BCLR2
2 DIR
4
BSET3
2 DIR
4
BCLR3
2 DIR
4
BSET4
2 DIR
4
BCLR4
2 DIR
4
BSET5
2 DIR
4
BCLR5
2 DIR
4
BSET6
2 DIR
4
BCLR6
2 DIR
4
BSET7
2 DIR
4
BCLR7
2 DIR
3
BRA
2 REL
3
BRN
2 REL
3
BHI
2 REL
3
BLS
2 REL
3
BCC
2 REL
3
BCS
2 REL
3
BNE
2 REL
3
BEQ
2 REL
3
BHCC
2 REL
3
BHCS
2 REL
3
BPL
2 REL
3
BMI
2 REL
3
BMC
2 REL
3
BMS
2 REL
3
BIL
2 REL
3
BIH
2 REL
Read-Modify-Write
INH
IX1
5
6
1
NEGX
1 INH
4
CBEQX
3 IMM
7
DIV
1 INH
1
COMX
1 INH
1
LSRX
1 INH
4
LDHX
2 DIR
1
RORX
1 INH
1
ASRX
1 INH
1
LSLX
1 INH
1
ROLX
1 INH
1
DECX
1 INH
3
DBNZX
2 INH
1
INCX
1 INH
1
TSTX
1 INH
4
MOV
2 DIX+
1
CLRX
1 INH
4
NEG
2
IX1
5
CBEQ
3 IX1+
3
NSA
1 INH
4
COM
2 IX1
4
LSR
2 IX1
3
CPHX
3 IMM
4
ROR
2 IX1
4
ASR
2 IX1
4
LSL
2 IX1
4
ROL
2 IX1
4
DEC
2 IX1
5
DBNZ
3 IX1
4
INC
2 IX1
3
TST
2 IX1
4
MOV
3 IMD
3
CLR
2 IX1
SP1
IX
9E6
7
Control
INH
INH
8
9
Register/Memory
IX2
SP2
IMM
DIR
EXT
A
B
C
D
9ED
4
SUB
3 EXT
4
CMP
3 EXT
4
SBC
3 EXT
4
CPX
3 EXT
4
AND
3 EXT
4
BIT
3 EXT
4
LDA
3 EXT
4
STA
3 EXT
4
EOR
3 EXT
4
ADC
3 EXT
4
ORA
3 EXT
4
ADD
3 EXT
3
JMP
3 EXT
5
JSR
3 EXT
4
LDX
3 EXT
4
STX
3 EXT
4
SUB
3 IX2
4
CMP
3 IX2
4
SBC
3 IX2
4
CPX
3 IX2
4
AND
3 IX2
4
BIT
3 IX2
4
LDA
3 IX2
4
STA
3 IX2
4
EOR
3 IX2
4
ADC
3 IX2
4
ORA
3 IX2
4
ADD
3 IX2
4
JMP
3 IX2
6
JSR
3 IX2
4
LDX
3 IX2
4
STX
3 IX2
5
SUB
4 SP2
5
CMP
4 SP2
5
SBC
4 SP2
5
CPX
4 SP2
5
AND
4 SP2
5
BIT
4 SP2
5
LDA
4 SP2
5
STA
4 SP2
5
EOR
4 SP2
5
ADC
4 SP2
5
ORA
4 SP2
5
ADD
4 SP2
IX1
SP1
IX
E
9EE
F
LSB
0
1
2
3
4
Central Processor Unit (CPU)
5
6
7
8
9
A
B
C
Freescale Semiconductor
MC68HC908LD64 — Rev. 3.0
D
E
F
4
1
NEG
NEGA
2 DIR 1 INH
5
4
CBEQ CBEQA
3 DIR 3 IMM
5
MUL
1 INH
4
1
COM
COMA
2 DIR 1 INH
4
1
LSR
LSRA
2 DIR 1 INH
4
3
STHX
LDHX
2 DIR 3 IMM
4
1
ROR
RORA
2 DIR 1 INH
4
1
ASR
ASRA
2 DIR 1 INH
4
1
LSL
LSLA
2 DIR 1 INH
4
1
ROL
ROLA
2 DIR 1 INH
4
1
DEC
DECA
2 DIR 1 INH
5
3
DBNZ DBNZA
3 DIR 2 INH
4
1
INC
INCA
2 DIR 1 INH
3
1
TST
TSTA
2 DIR 1 INH
5
MOV
3 DD
3
1
CLR
CLRA
2 DIR 1 INH
INH Inherent
REL Relative
IMM Immediate
IX
Indexed, No Offset
DIR Direct
IX1 Indexed, 8-Bit Offset
EXT Extended
IX2 Indexed, 16-Bit Offset
DD Direct-Direct
IMD Immediate-Direct
IX+D Indexed-Direct DIX+ Direct-Indexed
*Pre-byte for stack pointer indexed instructions
5
3
NEG
NEG
3 SP1 1 IX
6
4
CBEQ
CBEQ
4 SP1 2 IX+
2
DAA
1 INH
5
3
COM
COM
3 SP1 1 IX
5
3
LSR
LSR
3 SP1 1 IX
4
CPHX
2 DIR
5
3
ROR
ROR
3 SP1 1 IX
5
3
ASR
ASR
3 SP1 1 IX
5
3
LSL
LSL
3 SP1 1 IX
5
3
ROL
ROL
3 SP1 1 IX
5
3
DEC
DEC
3 SP1 1 IX
6
4
DBNZ
DBNZ
4 SP1 2 IX
5
3
INC
INC
3 SP1 1 IX
4
2
TST
TST
3 SP1 1 IX
4
MOV
2 IX+D
4
2
CLR
CLR
3 SP1 1 IX
SP1 Stack Pointer, 8-Bit Offset
SP2 Stack Pointer, 16-Bit Offset
IX+ Indexed, No Offset with
Post Increment
IX1+ Indexed, 1-Byte Offset with
Post Increment
7
3
RTI
BGE
1 INH 2 REL
4
3
RTS
BLT
1 INH 2 REL
3
BGT
2 REL
9
3
SWI
BLE
1 INH 2 REL
2
2
TAP
TXS
1 INH 1 INH
1
2
TPA
TSX
1 INH 1 INH
2
PULA
1 INH
2
1
PSHA
TAX
1 INH 1 INH
2
1
PULX
CLC
1 INH 1 INH
2
1
PSHX
SEC
1 INH 1 INH
2
2
PULH
CLI
1 INH 1 INH
2
2
PSHH
SEI
1 INH 1 INH
1
1
CLRH
RSP
1 INH 1 INH
1
NOP
1 INH
1
STOP
*
1 INH
1
1
WAIT
TXA
1 INH 1 INH
2
SUB
2 IMM
2
CMP
2 IMM
2
SBC
2 IMM
2
CPX
2 IMM
2
AND
2 IMM
2
BIT
2 IMM
2
LDA
2 IMM
2
AIS
2 IMM
2
EOR
2 IMM
2
ADC
2 IMM
2
ORA
2 IMM
2
ADD
2 IMM
3
SUB
2 DIR
3
CMP
2 DIR
3
SBC
2 DIR
3
CPX
2 DIR
3
AND
2 DIR
3
BIT
2 DIR
3
LDA
2 DIR
3
STA
2 DIR
3
EOR
2 DIR
3
ADC
2 DIR
3
ORA
2 DIR
3
ADD
2 DIR
2
JMP
2 DIR
4
4
BSR
JSR
2 REL 2 DIR
2
3
LDX
LDX
2 IMM 2 DIR
2
3
AIX
STX
2 IMM 2 DIR
MSB
0
3
SUB
2 IX1
3
CMP
2 IX1
3
SBC
2 IX1
3
CPX
2 IX1
3
AND
2 IX1
3
BIT
2 IX1
3
LDA
2 IX1
3
STA
2 IX1
3
EOR
2 IX1
3
ADC
2 IX1
3
ORA
2 IX1
3
ADD
2 IX1
3
JMP
2 IX1
5
JSR
2 IX1
5
3
LDX
LDX
4 SP2 2 IX1
5
3
STX
STX
4 SP2 2 IX1
4
SUB
3 SP1
4
CMP
3 SP1
4
SBC
3 SP1
4
CPX
3 SP1
4
AND
3 SP1
4
BIT
3 SP1
4
LDA
3 SP1
4
STA
3 SP1
4
EOR
3 SP1
4
ADC
3 SP1
4
ORA
3 SP1
4
ADD
3 SP1
2
SUB
1 IX
2
CMP
1 IX
2
SBC
1 IX
2
CPX
1 IX
2
AND
1 IX
2
BIT
1 IX
2
LDA
1 IX
2
STA
1 IX
2
EOR
1 IX
2
ADC
1 IX
2
ORA
1 IX
2
ADD
1 IX
2
JMP
1 IX
4
JSR
1 IX
4
2
LDX
LDX
3 SP1 1 IX
4
2
STX
STX
3 SP1 1 IX
High Byte of Opcode in Hexadecimal
LSB
Low Byte of Opcode in Hexadecimal
0
5
Cycles
BRSET0 Opcode Mnemonic
3 DIR Number of Bytes / Addressing Mode
Central Processor Unit (CPU)
Data Sheet
94
Table 6-2. Opcode Map
Bit Manipulation
DIR
DIR
Data Sheet — MC68HC908LD64
Section 7. Oscillator (OSC)
7.1 Contents
7.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
7.3
Oscillator External Connections . . . . . . . . . . . . . . . . . . . . . . . .96
7.4
I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
7.4.1
Crystal Amplifier Input Pin (OSC1). . . . . . . . . . . . . . . . . . . . 97
7.4.2
Crystal Amplifier Output Pin (OSC2) . . . . . . . . . . . . . . . . . . 97
7.4.3
Oscillator Enable Signal (SIMOSCEN). . . . . . . . . . . . . . . . . 97
7.4.4
External Clock Source (OSCXCLK) . . . . . . . . . . . . . . . . . . . 97
7.4.5
Oscillator Out (OSCOUT). . . . . . . . . . . . . . . . . . . . . . . . . . . 97
7.5
Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
7.5.1
Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
7.5.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
7.6
Oscillator During Break Mode. . . . . . . . . . . . . . . . . . . . . . . . . . 98
7.2 Introduction
The oscillator circuit is designed for use with crystals or ceramic
resonators. The oscillator circuit generates the crystal clock signal,
OSCXCLK, at the frequency of the crystal. This signal is divided by two
before being passed on to the SIM for bus clock generation. Figure 7-1
shows the structure of the oscillator. The oscillator requires various
external components.
The MC68HC908LD64 operates from a nominal 24MHz crystal or
external clock, providing an 8MHz internal bus clock. The 24MHz clock
is required for various modules, such as the CGM and USB.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Oscillator (OSC)
95
Oscillator (OSC)
7.3 Oscillator External Connections
In its typical configuration, the oscillator requires five external
components. The crystal oscillator is normally connected in a Pierce
oscillator configuration, as shown in Figure 7-1. This figure shows only
the logical representation of the internal components and may not
represent actual circuitry. The oscillator configuration uses five
components:
•
Crystal, X1 (nominally 24MHz)
•
Fixed capacitor, C1
•
Tuning capacitor, C2 (can also be a fixed capacitor)
•
Feedback resistor, RB
•
Series resistor, RS (not required for 24MHz crystal)
The series resistor (RS) is included in the diagram to follow strict Pierce
oscillator guidelines and may not be required for all ranges of operation,
especially with high frequency crystals. Refer to the crystal
manufacturer’s data for more information.
From
SIM
To SIM
OSCXCLK
To SIM
÷2
OSCOUT
SIMOSCEN
MCU
OSC1
OSC2
RS *
RB
X1
C1
24MHz
*RS can be zero (shorted) when used with
higher-frequency crystals. Refer to manufacturer’s data.
C2
Figure 7-1. Oscillator External Connections
Data Sheet
96
MC68HC908LD64 — Rev. 3.0
Oscillator (OSC)
Freescale Semiconductor
Oscillator (OSC)
I/O Signals
7.4 I/O Signals
The following paragraphs describe the oscillator I/O signals.
7.4.1 Crystal Amplifier Input Pin (OSC1)
The OSC1 pin is an input to the crystal oscillator amplifier.
An externally generated clock also can feed the OSC1 pin of the crystal
oscillator circuit. Connect the external clock to the OSC1 pin and let the
OSC2 pin float.
7.4.2 Crystal Amplifier Output Pin (OSC2)
The OSC2 pin is the output of the crystal oscillator inverting amplifier.
7.4.3 Oscillator Enable Signal (SIMOSCEN)
The SIMOSCEN signal comes from the SIM and enables the oscillator.
7.4.4 External Clock Source (OSCXCLK)
OSCXCLK is the crystal oscillator output signal. It runs at the full speed
of the crystal (fXCLK) and comes directly from the crystal oscillator circuit.
Figure 7-1 shows only the logical relation of OSCXCLK to OSC1 and
OSC2 and may not represent the actual circuitry. The duty cycle of
OSCXCLK is unknown and may depend on the crystal and other
external factors. Also, the frequency and amplitude of OSCXCLK can be
unstable at start-up.
7.4.5 Oscillator Out (OSCOUT)
The clock driven to the SIM is the crystal frequency divided by two. This
signal is driven to the SIM for generation of the bus clocks used by the
CPU and other modules on the MCU. OSCOUT will be divided again in
the SIM and results in the internal bus frequency being one fourth of the
OSCXCLK frequency.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Oscillator (OSC)
97
Oscillator (OSC)
7.5 Low Power Modes
The WAIT and STOP instructions put the MCU in low-powerconsumption standby modes.
7.5.1 Wait Mode
The WAIT instruction has no effect on the oscillator logic. OSCXCLK
continues to drive to the SIM module.
7.5.2 Stop Mode
The STOP instruction disables the OSCXCLK output.
7.6 Oscillator During Break Mode
The oscillator continues drive OSCXCLK when the chip enters the break
state.
Data Sheet
98
MC68HC908LD64 — Rev. 3.0
Oscillator (OSC)
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 8. Clock Generator Module (CGM)
8.1 Contents
8.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
8.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
8.4
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
8.4.1
Crystal Oscillator Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . .103
8.5
CGM I/O Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
8.5.1
External Filter Capacitor Pin (CGMXFC) . . . . . . . . . . . . . . 103
8.5.2
PLL Analog Power Pin (VDDA) . . . . . . . . . . . . . . . . . . . . . 103
8.5.3
PLL Analog Ground Pin (VSSA). . . . . . . . . . . . . . . . . . . . . 103
8.5.4
Crystal Output Frequency Signal (OSCXCLK). . . . . . . . . . 104
8.5.5
Crystal Reference Frequency Signal (OSCRCLK). . . . . . . 104
8.5.6
CGM Base Clock Output (DCLK1) . . . . . . . . . . . . . . . . . . . 104
8.5.7
CGM CPU Interrupt (CGMINT) . . . . . . . . . . . . . . . . . . . . . 104
8.6
CGM I/O Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
8.6.1
PLL Control Register (PCTL) . . . . . . . . . . . . . . . . . . . . . . . 105
8.6.2
PLL Bandwidth Control Register (PBWC) . . . . . . . . . . . . . 106
8.6.3
PLL Programming Register (PPG) . . . . . . . . . . . . . . . . . . . 108
8.6.4
H & V Sync Output Control Register (HVOCR) . . . . . . . . . 110
8.7
Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
8.8
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
8.8.1
Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
8.8.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
8.9
CGM During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . 112
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Clock Generator Module (CGM)
99
Clock Generator Module (CGM)
8.2 Introduction
This section describes the clock generator module (CGM). Using the
crystal reference clock from the oscillator module, the CGM generates
the display base clock, DCLK1, for the sync processor module. The
CGM is able to generate a frequency up to 108MHz from a 24MHz
reference clock.
8.3 Features
Features of the CGM include the following:
•
Phase-locked loop with output frequency in integer multiples of the
crystal reference
•
Programmable hardware voltage-controlled oscillator (VCO) for
low-jitter operation
•
Automatic bandwidth control mode for low-jitter operation
•
Automatic frequency lock detector
•
CPU interrupt on entry or exit from locked condition
8.4 Functional Description
The CGM consists of three major sub-modules:
•
Crystal oscillator circuit which generates the buffered constant
crystal frequency clock, OSCRCLK. (See Section 7. Oscillator
(OSC).)
•
Phase-locked loop (PLL) which generates the programmable
VCO frequency clock CGMVCLK.
•
Base clock selector circuit; this software-controlled circuit selects
either OSCXCLK divided by two or the VCO clock CGMVCLK
divided by two, as the base clock DCLK1. The sync processor
derives other display clocks from DCLK1.
Data Sheet
100
MC68HC908LD64 — Rev. 3.0
Clock Generator Module (CGM)
Freescale Semiconductor
Clock Generator Module (CGM)
Functional Description
OSCILLATOR (OSC)
(See Section 7. Oscillator (OSC).)
OSC2
OSCOUT
÷2
OSCXCLK
OSC1
(TO SIM)
SIMOSCEN
(FROM SIM)
PHASE-LOCKED LOOP (PLL)
HVOCR[1:0]
CGMRDV
OSCRCLK
REFERENCE
DIVIDER
CLOCK
SELECT
CIRCUIT
BCS
VDDA
CGMXFC
DCLK1
(TO SYNC PROCESSOR)
VSSA
VRS[7:4]
L
PHASE
DETECTOR
VOLTAGE
CONTROLLED
OSCILLATOR
LOOP
FILTER
PLL ANALOG
LOCK
DETECTOR
LOCK
BANDWIDTH
CONTROL
AUTO
ACQ
INTERRUPT
CONTROL
PLLIE
CGMINT
(TO SIM)
PLLF
MUL[7:4]
N
CGMVDV
FREQUENCY
DIVIDER
CGMVCLK
Figure 8-1. CGM Block Diagram
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Clock Generator Module (CGM)
101
Clock Generator Module (CGM)
Addr.
Register Name
$0038
Read:
PLL Control Register
Write:
(PCTL)
Reset:
$0039
Bit 7
PLLIE
0
PLL Bandwidth Control Read:
Register Write:
(PBWC)
Reset:
AUTO
PLL Programming Read:
Register Write:
(PPG)
Reset:
$003A
6
PLLF
0
LOCK
5
4
PLLON
BCS
1
0
ACQ
XLD
3
2
1
Bit 0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
MUL7
MUL6
MUL5
MUL4
VRS7
VRS6
VRS5
VRS4
0
1
1
0
0
1
1
0
H&V Sync Output Control Read:
$003F
Register Write:
(HVOCR)
Reset:
DCLKPH1 DCLKPH0
0
R
HVOCR1 HVOCR0
0
= Unimplemented
0
R
0
= Reserved
NOTES:
1. When AUTO = 0, PLLIE is forced to logic zero and is read-only.
2. When AUTO = 0, PLLF and LOCK read as logic zero.
3. When AUTO = 1, ACQ is read-only.
4. When PLLON = 0 or VRS[7:4] = $0, BCS is forced to logic zero and is read-only.
5. When PLLON = 1, the PLL programming register is read-only.
6. When BCS = 1, PLLON is forced set and is read-only.
Figure 8-2. CGM I/O Register Summary
Table 8-1. Free-Running HSOUT, VSOUT, DE, and DCLK Settings
Register Settings
Output Pin
Video Modes
HVOCR[1:0]
MUL[7:4]
VRS[7:4]
HOUT
Frequency
VOUT
Frequency
DCLK
Frequency
DE Video Mode
00
3
3
31.45kHz
59.91Hz
24MHz
VGA 640 × 480
01
5
3
37.87kHz
60.31Hz
40MHz
SVGA 800 × 600
10
8
6
48.37kHz
60.31Hz
64MHz
XGA 1024 × 768
11
9
9
64.32kHz
60.00Hz
108MHz
SXGA 1280 × 1024
Data Sheet
102
MC68HC908LD64 — Rev. 3.0
Clock Generator Module (CGM)
Freescale Semiconductor
Clock Generator Module (CGM)
CGM I/O Signals
8.4.1 Crystal Oscillator Circuit
The crystal oscillator circuit consists of an inverting amplifier and an
external crystal. The OSC1 pin is the input to the amplifier and the OSC2
pin is the output. The SIMOSCEN signal from the system integration
module (SIM) enables the crystal oscillator circuit.
The OSCXCLK signal is the output of the crystal oscillator circuit and
runs at a rate equal to the crystal frequency. OSCXCLK is then buffered
to produce OSCRCLK, the PLL reference clock. (See Section 7.
Oscillator (OSC).)
8.5 CGM I/O Signals
The following paragraphs describe the CGM I/O signals.
8.5.1 External Filter Capacitor Pin (CGMXFC)
The CGMXFC pin is required by the loop filter to filter out phase
corrections. A small external capacitor (CF) is connected to this pin.
NOTE:
To prevent noise problems, CF should be placed as close to the
CGMXFC pin as possible, with minimum routing distances and no
routing of other signals across the CF connection.
8.5.2 PLL Analog Power Pin (VDDA)
VDDA is the power pin used by the analog portions of the PLL. The pin
should be connected to the same voltage potential as the VDD pin.
8.5.3 PLL Analog Ground Pin (VSSA)
VSSA is the ground pin used by the analog portions of the PLL. The pin
should be connected to the same voltage potential as the VSS pin.
NOTE:
Route VDDA and VSSA carefully for maximum noise immunity and
place bypass capacitors as close as possible to the package.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Clock Generator Module (CGM)
103
Clock Generator Module (CGM)
8.5.4 Crystal Output Frequency Signal (OSCXCLK)
OSCXCLK is the crystal oscillator output signal. It runs at the full speed
of the crystal (fXCLK) and is generated directly from the crystal oscillator
circuit. The duty cycle of OSCXCLK is unknown and may depend on the
crystal and other external factors. Also, the frequency and amplitude of
OSCXCLK can be unstable at start-up.
8.5.5 Crystal Reference Frequency Signal (OSCRCLK)
OSCRCLK is the buffered version of OSCXCLK. It runs at the full speed
of the crystal (fXCLK) and provides the reference for the PLL circuit.
8.5.6 CGM Base Clock Output (DCLK1)
DCLK1 is the clock output of the CGM. This signal goes to the sync
processor, which generates the display clocks. DCLK1 is software
programmable to be either the oscillator output (OSCXCLK) or the VCO
clock (CGMVCLK).
8.5.7 CGM CPU Interrupt (CGMINT)
CGMINT is the interrupt signal generated by the PLL lock detector.
8.6 CGM I/O Registers
The following registers control and monitor operation of the CGM:
•
PLL control register (PCTL)
•
PLL bandwidth control register (PBWC)
•
PLL programming register (PPG)
•
H & V sync output control register (HVOCR)
Data Sheet
104
MC68HC908LD64 — Rev. 3.0
Clock Generator Module (CGM)
Freescale Semiconductor
Clock Generator Module (CGM)
CGM I/O Registers
8.6.1 PLL Control Register (PCTL)
The PLL control register contains the interrupt enable and flag bits, the
on/off switch, and the base clock selector bit.
Address:
$0038
Bit 7
Read:
6
5
4
PLLON
BCS
1
0
PLLF
PLLIE
3
2
1
Bit 0
1
1
1
1
1
1
1
1
Write:
Reset:
0
0
= Unimplemented
Figure 8-3. PLL Control Register (PCTL)
PLLIE — PLL Interrupt Enable Bit
This read/write bit enables the PLL to generate an interrupt request
when the LOCK bit toggles, setting the PLL flag, PLLF. When the
AUTO bit in the PLL bandwidth control register (PBWC) is clear,
PLLIE cannot be written and reads as 0. Reset clears the PLLIE bit.
1 = PLL interrupts enabled
0 = PLL interrupts disabled
PLLF — PLL Interrupt Flag Bit
This read-only bit is set whenever the LOCK bit toggles. PLLF
generates an interrupt request if the PLLIE bit is set also. PLLF
always reads as 0 when the AUTO bit in the PLL bandwidth control
register (PBWC) is clear. The PLLF bit should be cleared by reading
the PLL control register. Reset clears the PLLF bit.
1 = Change in lock condition
0 = No change in lock condition
NOTE:
The PLLF bit should not be inadvertently cleared. Any read or readmodify-write operation on the PLL control register clears the PLLF bit.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Clock Generator Module (CGM)
105
Clock Generator Module (CGM)
PLLON — PLL On Bit
This read/write bit activates the PLL and enables the VCO clock,
CGMVCLK. PLLON cannot be cleared if the VCO clock is driving the
base clock, DCLK1 (BCS = 1). Reset sets this bit so that the loop can
stabilize as the MCU is powering up.
1 = PLL on
0 = PLL off
BCS — Base Clock Select Bit
This read/write bit selects either the crystal oscillator output,
OSCXCLK, or the VCO clock, CGMVCLK, as the source of the CGM
output, DCLK1. BCS cannot be set while the PLLON bit is clear. After
toggling BCS, it may take up to three OSCXCLK and three CGMVCLK
cycles to complete the transition from one source clock to the other.
During the transition, DCLK1 is held in stasis. Reset and the STOP
instruction clear the BCS bit.
1 = DCLK1 driven by CGMVCLK
0 = DCLK1 driven by OSCXCLK
NOTE:
PLLON and BCS have built-in protection that prevents the base clock
selector circuit from selecting the VCO clock as the source of the base
clock if the PLL is off. Therefore, PLLON cannot be cleared when BCS
is set, and BCS cannot be set when PLLON is clear. If the PLL is off
(PLLON = 0), selecting CGMVCLK requires two writes to the PLL control
register.
8.6.2 PLL Bandwidth Control Register (PBWC)
The PLL bandwidth control register does the following:
•
Selects automatic or manual (software-controlled) bandwidth
control mode
•
Indicates when the PLL is locked
•
In automatic bandwidth control mode, indicates when the PLL is in
acquisition or tracking mode
•
In manual operation, forces the PLL into acquisition or tracking
mode
Data Sheet
106
MC68HC908LD64 — Rev. 3.0
Clock Generator Module (CGM)
Freescale Semiconductor
Clock Generator Module (CGM)
CGM I/O Registers
Address:
$0039
Bit 7
Read:
6
5
4
ACQ
XLD
0
0
LOCK
AUTO
3
2
1
Bit 0
0
0
0
0
0
0
0
0
Write:
Reset:
0
0
= Unimplemented
Figure 8-4. PLL Bandwidth Control Register (PBWC)
AUTO — Automatic Bandwidth Control Bit
This read/write bit selects automatic or manual bandwidth control.
When initializing the PLL for manual operation (AUTO = 0), the ACQ
bit should be cleared before turning the PLL on. Reset clears the
AUTO bit.
1 = Automatic bandwidth control
0 = Manual bandwidth control
LOCK — Lock Indicator Bit
When the AUTO bit is set, LOCK is a read-only bit that becomes set
when the VCO clock CGMVCLK, is locked (running at the
programmed frequency). When the AUTO bit is clear, LOCK reads
as 0 and has no meaning. Reset clears the LOCK bit.
1 = VCO frequency correct or locked
0 = VCO frequency incorrect or unlocked
ACQ — Acquisition Mode Bit
When the AUTO bit is set, ACQ is a read-only bit that indicates
whether the PLL is in acquisition mode or tracking mode. When the
AUTO bit is clear, ACQ is a read/write bit that controls whether the
PLL is in acquisition or tracking mode.
In automatic bandwidth control mode (AUTO = 1), the last-written
value from manual operation is stored in a temporary location and is
recovered when manual operation resumes. Reset clears this bit,
enabling acquisition mode.
1 = Tracking mode
0 = Acquisition mode
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Clock Generator Module (CGM)
107
Clock Generator Module (CGM)
XLD — Crystal Loss Detect Bit
When the VCO output, CGMVCLK, is driving DCLK1, this read/write
bit indicates whether the crystal reference frequency is active or not.
To check the status of the crystal reference, the following procedure
should be followed:
1. Write a 1 to XLD.
2. Wait 4 × N cycles. (N is the VCO frequency multiplier, MUL[7:4].)
3. Read XLD.
1 = Crystal reference is not active
0 = Crystal reference is active
The crystal loss detect function works only when the BCS bit is set,
selecting CGMVCLK to drive DCLK1. When BCS is clear, XLD always
reads as 0.
Bits [3:0] — Reserved for test
These bits enable test functions not available in user mode. To ensure
software portability from development systems to user applications,
software should write zeros to Bits [3:0] whenever writing to PBWC.
8.6.3 PLL Programming Register (PPG)
The PLL programming register contains the programming information for
the modulo feedback divider and the programming information for the
hardware configuration of the VCO.
Address:
$003A
Bit 7
6
5
4
3
2
1
Bit 0
MUL7
MUL6
MUL5
MUL4
VRS7
VRS6
VRS5
VRS4
0
1
1
0
0
1
1
0
Read:
Write:
Reset:
Figure 8-5. PLL Programming Register (PPG)
Data Sheet
108
MC68HC908LD64 — Rev. 3.0
Clock Generator Module (CGM)
Freescale Semiconductor
Clock Generator Module (CGM)
CGM I/O Registers
MUL[7:4] — Multiplier Select Bits
These read/write bits control the modulo feedback divider that selects
the VCO frequency multiplier, N. A value of $0 in the multiplier select
bits configures the modulo feedback divider the same as a value of
$1. Reset initializes these bits to $6 to give a default multiply value
of 6.
Table 8-2. VCO Frequency Multiplier (N) Selection
NOTE:
MUL7:MUL6:MUL5:MUL4
VCO Frequency Multiplier (N)
0000
1
0001
1
0010
2
0011
3
1101
13
1110
14
1111
15
The multiplier select bits have built-in protection that prevents them from
being written when the PLL is on (PLLON = 1).
VRS[7:4] — VCO Range Select Bits
These read/write bits control the hardware center-of-range linear
multiplier L, which controls the hardware center-of-range frequency
fVRS. VRS[7:4] cannot be written when the PLLON bit in the PLL
control register (PCTL) is set. A value of $0 in the VCO range select
bits disables the PLL and clears the BCS bit in the PCTL. Reset
initializes the bits to $6 to give a default range multiply value of 6.
NOTE:
The VCO range select bits have built-in protection that prevents them
from being written when the PLL is on (PLLON = 1) and prevents
selection of the VCO clock as the source of the base clock (BCS = 1) if
the VCO range select bits are all clear.
The VCO range select bits must be programmed correctly. Incorrect
programming may result in failure of the PLL to achieve lock.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Clock Generator Module (CGM)
109
Clock Generator Module (CGM)
8.6.4 H & V Sync Output Control Register (HVOCR)
The H&V sync output control register controls the PLL reference input
prescaler and the final free-running waveforms for the sync processor
output signals on HOUT, VOUT, DCLK, and DE pins.
(See Section 17. Sync Processor.)
Address:
$003F
Bit 7
6
5
4
3
2
1
Bit 0
Read:
DCLKPH1 DCLKPH0
R
HVOCR1 HVOCR0
Write:
Reset:
0
= Unimplemented
0
0
R
0
= Reserved
Figure 8-6. H&V Sync Output Control Register (HVOCR)
DCLKPH[1:0] — DCLK Output Phase Adjustment
These two bits are programmed to adjust the DCLK output phase.
Each increment adds approximately 2 to 3ns delay to the DCLK output.
HVOCR[1:0] — Free Running Video Mode Select Bits
These two bits together with MUL[7:4] and VRS[7:4] in the PLL
programming register determine the frequencies of the internal
generated free-running signals for output to HOUT, VOUT, DE, and
DCLK pins, when the SOUT bit is set in the sync processor I/O control
register. These two bits determine the prescaler of PLL reference
clock in the CGM module. When HVOCR[1:0]=11, the prescaler is 2;
for other values, the prescaler is 3. Reset clears these bits, setting a
default horizontal frequency of 31.25kHz and a vertical frequency of
60Hz, a video mode of 640×480.
Register Settings
Pin Outputs
Video Modes
HVOCR[1:0]
MUL[7:4]
VRS[7:4]
HOUT
Frequency
VOUT
Frequency
DCLK
Frequency
DE Video Mode
00
3
3
31.45kHz
59.91Hz
24MHz
VGA 640 × 480
01
5
3
37.87kHz
60.31Hz
40MHz
SVGA 800 × 600
10
8
6
48.37kHz
60.31Hz
64MHz
XGA 1024 × 768
11
9
9
64.32kHz
60.00Hz
108MHz
SXGA 1280 × 1024
Data Sheet
110
MC68HC908LD64 — Rev. 3.0
Clock Generator Module (CGM)
Freescale Semiconductor
Clock Generator Module (CGM)
Interrupts
8.7 Interrupts
When the AUTO bit is set in the PLL bandwidth control register (PBWC),
the PLL can generate a CPU interrupt request every time the LOCK bit
changes state. The PLLIE bit in the PLL control register (PCTL) enables
CPU interrupts from the PLL. PLLF, the interrupt flag in the PCTL,
becomes set whether interrupts are enabled or not. When the AUTO bit
is clear, CPU interrupts from the PLL are disabled and PLLF reads as 0.
Software should read the LOCK bit after a PLL interrupt request to see
if the request was due to an entry into lock or an exit from lock. When the
PLL enters lock, the VCO clock CGMVCLK, can be selected as the
DCLK1 source by setting BCS in the PCTL. When the PLL exits lock, the
VCO clock frequency is corrupt, and appropriate precautions should be
taken. If the application is not frequency-sensitive, interrupts should be
disabled to prevent PLL interrupt service routines from impeding
software performance or from exceeding stack limitations.
Software can select CGMVCLK as the DCLK1 source even if the PLL is
not locked (LOCK = 0). Therefore, software should make sure the PLL
is locked before setting the BCS bit.
8.8 Low-Power Modes
The WAIT and STOP instructions put the MCU in low-powerconsumption standby modes.
8.8.1 Wait Mode
The WAIT instruction does not affect the CGM. Before entering WAIT
mode, software can disengage and turn off the PLL by clearing the BCS
and PLLON bits in the PLL control register (PCTL). Less power-sensitive
applications can disengage the PLL without turning it off. Applications
that require the PLL to wake the MCU from WAIT mode also can
deselect the PLL output without turning off the PLL.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Clock Generator Module (CGM)
111
Clock Generator Module (CGM)
8.8.2 Stop Mode
When the STOP instruction executes, the SIM drives the SIMOSCEN
signal low, disabling the CGM and holding low all CGM outputs
(OSCXCLK, DCLK1, and CGMINT).
If the STOP instruction is executed with the VCO clock, CGMVCLK,
driving DCLK1, the PLL automatically clears the BCS bit in the PLL
control register (PCTL), thereby selecting the crystal clock, OSCXCLK,
as the source of DCLK1. When the MCU recovers from STOP, the
crystal clock drives DCLK1 and BCS remains clear.
8.9 CGM During Break Interrupts
The system integration module (SIM) controls whether status bits in
other modules can be cleared during the break state. The BCFE bit in
the SIM break flag control register (SBFCR) enables software to clear
status bits during the break state. See Section 9. System Integration
Module (SIM).
To allow software to clear status bits during a break interrupt, a 1 should
be written to the BCFE bit. If a status bit is cleared during the break state,
it remains cleared when the MCU exits the break state.
To protect the PLLF bit during the break state, write a 0 to the BCFE bit.
With BCFE at 0 (its default state), software can read and write the PLL
control register during the break state without affecting the PLLF bit.
Data Sheet
112
MC68HC908LD64 — Rev. 3.0
Clock Generator Module (CGM)
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 9. System Integration Module (SIM)
9.1 Contents
9.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
9.3
SIM Bus Clock Control and Generation . . . . . . . . . . . . . . . . . 117
9.3.1
Bus Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
9.3.2
Clock Start-Up from POR . . . . . . . . . . . . . . . . . . . . . . . . . . 117
9.3.3
Clocks in Stop Mode and Wait Mode . . . . . . . . . . . . . . . . . 117
9.4
Reset and System Initialization. . . . . . . . . . . . . . . . . . . . . . . . 118
9.4.1
External Pin Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
9.4.2
Active Resets from Internal Sources . . . . . . . . . . . . . . . . . 119
9.4.2.1
Power-On Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
9.4.2.2
Computer Operating Properly (COP) Reset. . . . . . . . . . 121
9.4.2.3
Low-Voltage Inhibit Reset . . . . . . . . . . . . . . . . . . . . . . .121
9.4.2.4
Illegal Opcode Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
9.4.2.5
Illegal Address Reset . . . . . . . . . . . . . . . . . . . . . . . . . . .122
9.5
SIM Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
9.5.1
SIM Counter During Power-On Reset . . . . . . . . . . . . . . . . 122
9.5.2
SIM Counter During Stop Mode Recovery . . . . . . . . . . . . . 122
9.5.3
SIM Counter and Reset States. . . . . . . . . . . . . . . . . . . . . . 123
9.6
Exception Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123
9.6.1
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
9.6.1.1
Hardware Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
9.6.1.2
SWI Instruction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
9.6.2
Interrupt Status Registers. . . . . . . . . . . . . . . . . . . . . . . . . . 127
9.6.2.1
Interrupt Status Register 1 . . . . . . . . . . . . . . . . . . . . . . . 129
9.6.2.2
Interrupt Status Register 2 . . . . . . . . . . . . . . . . . . . . . . . 129
9.6.3
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
9.6.4
Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
9.6.5
Status Flag Protection in Break Mode . . . . . . . . . . . . . . . . 130
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
System Integration Module (SIM)
113
System Integration Module (SIM)
9.7
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
9.7.1
Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131
9.7.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132
9.8
SIM Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
9.8.1
SIM Break Status Register (SBSR) . . . . . . . . . . . . . . . . . . 134
9.8.2
SIM Reset Status Register (SRSR) . . . . . . . . . . . . . . . . . . 135
9.8.3
SIM Break Flag Control Register (SBFCR) . . . . . . . . . . . . 136
9.2 Introduction
This section describes the system integration module, which supports up
to 16 external and/or internal interrupts. Together with the CPU, the SIM
controls all MCU activities. A block diagram of the SIM is shown in
Figure 9-1. Figure 9-2 shows a summary of the SIM I/O registers. The
SIM is a system state controller that coordinates CPU and exception
timing. The SIM is responsible for:
•
Bus clock generation and control for CPU and peripherals:
– Stop/wait/reset/break entry and recovery
– Internal clock control
•
Master reset control, including power-on reset (POR) and COP
timeout
•
Interrupt control:
– Acknowledge timing
– Arbitration control timing
– Vector address generation
•
CPU enable/disable timing
•
Modular architecture expandable to 128 interrupt sources
Data Sheet
114
MC68HC908LD64 — Rev. 3.0
System Integration Module (SIM)
Freescale Semiconductor
System Integration Module (SIM)
Introduction
MODULE STOP
MODULE WAIT
CPU STOP (FROM CPU)
CPU WAIT (FROM CPU)
STOP/WAIT
CONTROL
SIMOSCEN (TO OSCILLATOR)
SIM
COUNTER
COP CLOCK
OSCXCLK (FROM OSCILLATOR)
OSCOUT (FROM OSCILLATOR)
÷2
CLOCK
CONTROL
RESET
PIN LOGIC
CLOCK GENERATORS
INTERNAL CLOCKS
LVI (FROM LVI MODULE)
POR CONTROL
MASTER
RESET
CONTROL
RESET PIN CONTROL
SIM RESET STATUS REGISTER
ILLEGAL OPCODE (FROM CPU)
ILLEGAL ADDRESS (FROM ADDRESS
MAP DECODERS)
COP (FROM COP MODULE)
LVI RESET
RESET
INTERRUPT CONTROL
AND PRIORITY DECODE
INTERRUPT SOURCES
CPU INTERFACE
Figure 9-1. SIM Block Diagram
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
System Integration Module (SIM)
115
System Integration Module (SIM)
Addr.
Register Name
Bit 7
6
5
4
3
2
R
R
R
R
R
R
Read:
SIM Break Status Register
$FE00
Write:
(SBSR)
Reset:
Read:
SIM Reset Status Register
$FE01
Write:
(SRSR)
POR:
$FE03
Read:
SIM Break Flag Control
Register Write:
(SBFCR)
Reset:
1
SBSW
Note
Bit 0
R
0
POR
PIN
COP
ILOP
ILAD
USB
0
0
1
0
0
0
0
0
0
0
BCFE
R
R
R
R
R
R
R
0
Read:
Interrupt Status Register 1
$FE04
Write:
(INT1)
Reset:
IF6
IF5
IF4
IF3
IF2
IF1
0
0
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
Read:
Interrupt Status Register 2
$FE05
(INT2) Write:
IF14
IF13
IF12
IF11
IF10
IF9
IF8
IF7
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
Reset:
= Unimplemented
Note: Writing a logic 0 clears SBSW.
R
= Reserved
Figure 9-2. SIM I/O Register Summary
Table 9-1 shows the internal signal names used in this section.
Table 9-1. Signal Name Conventions
Signal Name
Description
OSCXCLK
Buffered version of OSC1 from the oscillator
OSCOUT
The OSCXCLK frequency divided by two. This signal is again
divided by two in the SIM to generate the internal bus clocks.
(Bus clock = OSCXCLK divided by four)
IAB
Internal address bus
IDB
Internal data bus
PORRST
Signal from the power-on reset module to the SIM
IRST
Internal reset signal
R/W
Read/write signal
Data Sheet
116
MC68HC908LD64 — Rev. 3.0
System Integration Module (SIM)
Freescale Semiconductor
System Integration Module (SIM)
SIM Bus Clock Control and Generation
9.3 SIM Bus Clock Control and Generation
The bus clock generator provides system clock signals for the CPU and
peripherals on the MCU. The system clocks are generated from an
incoming clock, OSCOUT, as shown in Figure 9-3.
From
SIM
OSCXCLK
÷2
OSCOUT
SIM COUNTER
BUS CLOCK
GENERATORS
÷2
SIMOSCEN
OSCILLATOR
OSC1
SIM
OSC2
Figure 9-3. OSC Clock Signals
9.3.1 Bus Timing
In user mode, the internal bus frequency is the oscillator frequency
(OSCXCLK) divided by four.
9.3.2 Clock Start-Up from POR
When the power-on reset module generates a reset, the clocks to the
CPU and peripherals are inactive and held in an inactive phase until after
the 4096 OSCXCLK cycle POR timeout has completed. The RST is
driven low by the SIM during this entire period. The IBUS clocks start
upon completion of the timeout.
9.3.3 Clocks in Stop Mode and Wait Mode
Upon exit from stop mode (by an interrupt, break, or reset), the SIM
allows OSCXCLK to clock the SIM counter. The CPU and peripheral
clocks do not become active until after the stop delay timeout. This
timeout is selectable as 4096 or 32 OSCXCLK cycles. (See 9.7.2 Stop
Mode.)
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
System Integration Module (SIM)
117
System Integration Module (SIM)
In wait mode, the CPU clocks are inactive. The SIM also produces two
sets of clocks for other modules. Refer to the wait mode subsection of
each module to see if the module is active or inactive in wait mode.
Some modules can be programmed to be active in wait mode.
9.4 Reset and System Initialization
The MCU has the following reset sources:
•
Power-on reset module (POR)
•
External reset pin (RST)
•
Computer operating properly module (COP)
•
Low-voltage inhibit (LVI)
•
Illegal opcode
•
Illegal address
All of these resets produce the vector $FFFE–$FFFF ($FEFE–$FEFF in
monitor mode) and assert the internal reset signal (IRST). IRST causes
all registers to be returned to their default values and all modules to be
returned to their reset states.
An internal reset clears the SIM counter (see 9.5 SIM Counter), but an
external reset does not. Each of the resets sets a corresponding bit in
the SIM reset status register (SRSR) (see 9.8 SIM Registers).
9.4.1 External Pin Reset
Pulling the asynchronous RST pin low halts all processing. The PIN bit
of the SIM reset status register (SRSR) is set as long as RST is held low
for a minimum of 67 OSCXCLK cycles, assuming that the POR was not
the source of the reset (see Table 9-2. PIN Bit Set Timing). Figure 9-4
shows the relative timing.
Table 9-2. PIN Bit Set Timing
Reset Type
Number of Cycles Required to Set PIN
POR
4163 (4096 + 64 + 3)
All others
67 (64 + 3)
Data Sheet
118
MC68HC908LD64 — Rev. 3.0
System Integration Module (SIM)
Freescale Semiconductor
System Integration Module (SIM)
Reset and System Initialization
OSCOUT
RST
IAB
VECT H VECT L
PC
Figure 9-4. External Reset Timing
9.4.2 Active Resets from Internal Sources
SIM module in HC08 has the capability to drive the RST pin low when
internal reset events occur.
All internal reset sources actively pull the RST pin low for 32 OSCXCLK
cycles to allow resetting of external peripherals. The internal reset signal
IRST continues to be asserted for an additional 32 cycles (see Figure 95. Internal Reset Timing). An internal reset can be caused by an illegal
address, illegal opcode, COP timeout, or POR (see Figure 9-6. Sources
of Internal Reset). Note that for POR resets, the SIM cycles through
4096 OSCXCLK cycles during which the SIM forces the RST pin low.
The internal reset signal then follows the sequence from the falling edge
of RST shown in Figure 9-5.
The COP reset is asynchronous to the bus clock.
The active reset feature allows the part to issue a reset to peripherals
and other chips within a system built around the MCU.
IRST
RST
RST PULLED LOW BY MCU
32 CYCLES
32 CYCLES
OSCXCLK
IAB
VECTOR HIGH
Figure 9-5. Internal Reset Timing
ILLEGAL ADDRESS RST
ILLEGAL OPCODE RST
COPRST
INTERNAL RESET
POR
LVI
Figure 9-6. Sources of Internal Reset
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
System Integration Module (SIM)
119
System Integration Module (SIM)
9.4.2.1 Power-On Reset
When power is first applied to the MCU, the power-on reset module
(POR) generates a pulse to indicate that power-on has occurred. The
external reset pin (RST) is held low while the SIM counter counts out
4096 OSCXCLK cycles. Sixty-four OSCXCLK cycles later, the CPU and
memories are released from reset to allow the reset vector sequence to
occur.
At power-on, the following events occur:
•
A POR pulse is generated.
•
The internal reset signal is asserted.
•
The SIM enables the oscillator to drive OSCXCLK.
•
Internal clocks to the CPU and modules are held inactive for 4096
OSCXCLK cycles to allow stabilization of the oscillator.
•
The RST pin is driven low during the oscillator stabilization time.
•
The POR bit of the SIM reset status register (SRSR) is set and all
other bits in the register are cleared.
OSC1
PORRST
4096
CYCLES
32
CYCLES
32
CYCLES
OSCXCLK
OSCOUT
RST
$FFFE
IAB
$FFFF
Figure 9-7. POR Recovery
Data Sheet
120
MC68HC908LD64 — Rev. 3.0
System Integration Module (SIM)
Freescale Semiconductor
System Integration Module (SIM)
Reset and System Initialization
9.4.2.2 Computer Operating Properly (COP) Reset
An input to the SIM is reserved for the COP reset signal. The overflow of
the COP counter causes an internal reset and sets the COP bit in the
SIM reset status register (SRSR). The SIM actively pulls down the RST
pin for all internal reset sources.
To prevent a COP module timeout, write any value to location $FFFF.
Writing to location $FFFF clears the COP counter and bits 12 through 5
of the SIM counter. The SIM counter output, which occurs at least every
212 – 24 OSCXCLK cycles, drives the COP counter. The COP should be
serviced as soon as possible out of reset to guarantee the maximum
amount of time before the first timeout.
The COP module is disabled if the RST pin or the IRQ is held at VTST
while the MCU is in monitor mode. The COP module can be disabled
only through combinational logic conditioned with the high voltage signal
on the RST pin or the IRQ pin. This prevents the COP from becoming
disabled as a result of external noise. During a break state, VTST on the
RST pin disables the COP module.
9.4.2.3 Low-Voltage Inhibit Reset
The low-voltage inhibit circuit performs an internal reset when the VDD
voltage falls to the LVI trip voltage VTRIPF. The external reset pin (RST)
is held low while the SIM counter counts out 4096 OSCXCLK cycles.
Sixty-four OSCXCLK cycles later, the CPU and memories are released
from reset to allow the reset vector sequence to occur.
9.4.2.4 Illegal Opcode Reset
The SIM decodes signals from the CPU to detect illegal instructions. An
illegal instruction sets the ILOP bit in the SIM reset status register
(SRSR) and causes a reset.
If the stop enable bit, STOP, in the configure register (CONFIG) is logic
zero, the SIM treats the STOP instruction as an illegal opcode and
causes an illegal opcode reset. The SIM actively pulls down the RST pin
for all internal reset sources.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
System Integration Module (SIM)
121
System Integration Module (SIM)
9.4.2.5 Illegal Address Reset
An opcode fetch from an unmapped address generates an illegal
address reset. The SIM verifies that the CPU is fetching an opcode prior
to asserting the ILAD bit in the SIM reset status register (SRSR) and
resetting the MCU. A data fetch from an unmapped address does not
generate a reset. The SIM actively pulls down the RST pin for all internal
reset sources.
9.5 SIM Counter
The SIM counter is used by the power-on reset module (POR) and in
stop mode recovery to allow the oscillator time to stabilize before
enabling the internal bus (IBUS) clocks. The SIM counter also serves as
a prescaler for the computer operating properly module (COP). The SIM
counter overflow supplies the clock for the COP module. The SIM
counter is 12 bits long and is clocked by the falling edge of OSCXCLK.
9.5.1 SIM Counter During Power-On Reset
The power-on reset module (POR) detects power applied to the MCU.
At power-on, the POR circuit asserts the signal PORRST. Once the SIM
is initialized, it enables the oscillator to drive the bus clock state machine.
9.5.2 SIM Counter During Stop Mode Recovery
The SIM counter also is used for stop mode recovery. The STOP
instruction clears the SIM counter. After an interrupt, break, or reset, the
SIM senses the state of the short stop recovery bit, SSREC, in the
configure register (CONFIG). If the SSREC bit is a logic one, then the
stop recovery is reduced from the normal delay of 4096 OSCXCLK
cycles down to 32 OSCXCLK cycles. This is ideal for applications using
canned oscillators that do not require long start-up times from stop
mode. External crystal applications should use the full stop recovery
time, that is, with SSREC cleared.
Data Sheet
122
MC68HC908LD64 — Rev. 3.0
System Integration Module (SIM)
Freescale Semiconductor
System Integration Module (SIM)
Exception Control
9.5.3 SIM Counter and Reset States
External reset has no effect on the SIM counter (see 9.7.2 Stop Mode).
The SIM counter is free-running after all reset states (see 9.4.2 Active
Resets from Internal Sources for counter control and internal reset
recovery sequences).
9.6 Exception Control
Normally, sequential program execution can be changed in three
different ways:
•
Interrupts
– Maskable hardware CPU interrupts
– Non-maskable software interrupt instruction (SWI)
•
Reset
•
Break interrupts
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
System Integration Module (SIM)
123
System Integration Module (SIM)
9.6.1 Interrupts
An interrupt temporarily changes the sequence of program execution to
respond to a particular event. Figure 9-10 flow charts the handling of
system interrupts.
Interrupts are latched, and arbitration is performed in the SIM at the start
of interrupt processing. The arbitration result is a constant that the CPU
uses to determine which vector to fetch. Once an interrupt is latched by
the SIM, no other interrupt can take precedence, regardless of priority,
until the latched interrupt is serviced (or the I bit is cleared).
At the beginning of an interrupt, the CPU saves the CPU register
contents on the stack and sets the interrupt mask (I bit) to prevent
additional interrupts. At the end of an interrupt, the RTI instruction
recovers the CPU register contents from the stack so that normal
processing can resume. Figure 9-8 shows interrupt entry timing. Figure
9-9 shows interrupt recovery timing.
MODULE
INTERRUPT
I BIT
IAB
IDB
DUMMY
DUMMY
SP
SP – 1
SP – 2
PC – 1[7:0] PC – 1[15:8]
SP – 3
X
SP – 4
A
VECT H
CCR
VECT L
V DATA H
START ADDR
V DATA L
OPCODE
R/W
Figure 9-8. Interrupt Entry
MODULE
INTERRUPT
I BIT
IAB
IDB
SP – 4
SP – 3
CCR
SP – 2
A
SP – 1
X
SP
PC
PC – 1[15:8] PC – 1[7:0]
PC + 1
OPCODE
OPERAND
R/W
Figure 9-9. Interrupt Recovery
Data Sheet
124
MC68HC908LD64 — Rev. 3.0
System Integration Module (SIM)
Freescale Semiconductor
System Integration Module (SIM)
Exception Control
FROM RESET
BREAK
INTERRUPT?
I BIT
SET?
YES
NO
YES
I BIT SET?
NO
IRQ
INTERRUPT?
YES
NO
USB
INTERRUPT?
YES
NO
STACK CPU REGISTERS.
SET I BIT.
LOAD PC WITH INTERRUPT VECTOR.
(As many interrupts as exist on chip)
FETCH NEXT
INSTRUCTION.
SWI
INSTRUCTION?
YES
NO
RTI
INSTRUCTION?
YES
UNSTACK CPU REGISTERS.
NO
EXECUTE INSTRUCTION.
Figure 9-10. Interrupt Processing
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
System Integration Module (SIM)
125
System Integration Module (SIM)
Interrupts are latched, and arbitration is performed in the SIM at the start
of interrupt processing. The arbitration result is a constant that the CPU
uses to determine which vector to fetch. Once an interrupt is latched by
the SIM, no other interrupt may take precedence, regardless of priority,
until the latched interrupt is serviced (or the I bit is cleared). (See Figure
9-10. Interrupt Processing.)
9.6.1.1 Hardware Interrupts
A hardware interrupt does not stop the current instruction. Processing of
a hardware interrupt begins after completion of the current instruction.
When the current instruction is complete, the SIM checks all pending
hardware interrupts. If interrupts are not masked (I bit clear in the
condition code register), and if the corresponding interrupt enable bit is
set, the SIM proceeds with interrupt processing; otherwise, the next
instruction is fetched and executed.
If more than one interrupt is pending at the end of an instruction
execution, the highest priority interrupt is serviced first. Figure 9-11
demonstrates what happens when two interrupts are pending. If an
interrupt is pending upon exit from the original interrupt service routine,
the pending interrupt is serviced before the LDA instruction is executed.
CLI
LDA #$FF
INT1
BACKGROUND ROUTINE
PSHH
INT1 INTERRUPT SERVICE ROUTINE
PULH
RTI
INT2
PSHH
INT2 INTERRUPT SERVICE ROUTINE
PULH
RTI
Figure 9-11. Interrupt Recognition Example
Data Sheet
126
MC68HC908LD64 — Rev. 3.0
System Integration Module (SIM)
Freescale Semiconductor
System Integration Module (SIM)
Exception Control
The LDA opcode is pre-fetched by both the INT1 and INT2 RTI
instructions. However, in the case of the INT1 RTI pre-fetch, this is a
redundant operation.
NOTE:
To maintain compatibility with the M6805 Family, the H register is not
pushed on the stack during interrupt entry. If the interrupt service routine
modifies the H register or uses the indexed addressing mode, software
should save the H register and then restore it prior to exiting the routine.
9.6.1.2 SWI Instruction
The SWI instruction is a non-maskable instruction that causes an
interrupt regardless of the state of the interrupt mask (I bit) in the
condition code register.
NOTE:
A software interrupt pushes PC onto the stack. A software interrupt does
not push PC – 1, as a hardware interrupt does.
9.6.2 Interrupt Status Registers
The flags in the interrupt status registers identify maskable interrupt
sources. Table 9-3 summarizes the interrupt sources and the interrupt
status register flags that they set. The interrupt status registers can be
useful for debugging.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
System Integration Module (SIM)
127
System Integration Module (SIM)
Table 9-3. Interrupt Sources
Flag
Mask(1)
INT Register
Flag
Priority(2)
Vector
Address
Reset
None
None
None
0
$FFFE–$FFFF
SWI Instruction
None
None
None
0
$FFFC–$FFFD
IRQ pin
IRQF
IMASK
IF1
1
$FFFA–$FFFB
HUB start of frame
SOFF
SOFIE
HUB 2nd end of frame point
EOF2F
EOF2IE
HUB end of packet
EOPF
EOPIE
IF2
2
$FFF8–$FFF9
TRANF
TRANIE
HUB endpoint 0 transmit
TXDF
TXDIE
HUB endpoint 0 receive
RXDF
RXDIE
IF3
3
$FFF6–$FFF7
Device endpoint 0 transmit
TXD0F
TXD0IE
Device endpoint 0 receive
RXD0F
RXD0IE
IF4
4
$FFF4–$FFF5
USB endpoint1/2 transmit
TXD1F
TXD1IE
IF5
5
$FFF2–$FFF3
Source
HUB bus signal transition detect
ALIF
NAKIF
DDC12AB
RXIF
DIEN
TXIF
SCLIF
SCLIEN
TIM channel 0
CH0F
CH0IE
IF6
6
$FFF0–$FFF1
TIM channel 1
CH1F
CH1IE
IF7
7
$FFEE–$FFEF
TOF
TOIE
IF8
8
$FFEC–$FFED
VSIF
VSIE
LVSIF
LVSIE
IF9
9
$FFEA–$FFEB
MMIEN
IF10
10
$FFE8–$FFE9
DENDIF
OSDIE
IF11
11
$FFE6–$FFE7
ADC conversion complete
COCO
AIEN
IF12
12
$FFE4–$FFE5
Keyboard Interrupt
KEYF
KBIE7–KBIE0
IF13
13
$FFE2–$FFE3
CGM PLL
PLLF
PLLIE
IF14
14
$FFE0–$FFE1
TIM overflow
Sync processor
MMALIF
Multi-master IIC
MMNAKIF
MMRXIF
MMTXIF
On-screen display
Notes:
1. The I bit in the condition code register is a global mask for all interrupt sources except the SWI instruction.
2. Highest priority = 0.
Data Sheet
128
MC68HC908LD64 — Rev. 3.0
System Integration Module (SIM)
Freescale Semiconductor
System Integration Module (SIM)
Exception Control
9.6.2.1 Interrupt Status Register 1
Address:
$FE04
Bit 7
6
5
4
3
2
1
Bit 0
Read:
IF6
IF5
IF4
IF3
IF2
IF1
0
0
Write:
R
R
R
R
R
R
R
R
Reset:
0
0
0
0
0
0
0
0
R
= Reserved
Figure 9-12. Interrupt Status Register 1 (INT1)
IF6–IF1 — Interrupt Flags 6–1
These flags indicate the presence of interrupt requests from the
sources shown in Table 9-3.
1 = Interrupt request present
0 = No interrupt request present
Bit 1 and Bit 0 — Always read 0
9.6.2.2 Interrupt Status Register 2
Address:
$FE05
Bit 7
6
5
4
3
2
1
Bit 0
Read:
IF14
IF13
IF12
IF11
IF10
IF9
IF8
IF7
Write:
R
R
R
R
R
R
R
R
Reset:
0
0
0
0
0
0
0
0
R
= Reserved
Figure 9-13. Interrupt Status Register 2 (INT2)
IF14–IF7 — Interrupt Flags 14–7
These flags indicate the presence of interrupt requests from the
sources shown in Table 9-3.
1 = Interrupt request present
0 = No interrupt request present
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
System Integration Module (SIM)
129
System Integration Module (SIM)
9.6.3 Reset
All reset sources always have equal and highest priority and cannot be
arbitrated.
9.6.4 Break Interrupts
The break module can stop normal program flow at a softwareprogrammable break point by asserting its break interrupt output (see
Section 23. Break Module (BRK)). The SIM puts the CPU into the
break state by forcing it to the SWI vector location. Refer to the break
interrupt subsection of each module to see how each module is affected
by the break state.
9.6.5 Status Flag Protection in Break Mode
The SIM controls whether status flags contained in other modules can
be cleared during break mode. The user can select whether flags are
protected from being cleared by properly initializing the break clear flag
enable bit (BCFE) in the SIM break flag control register (SBFCR).
Protecting flags in break mode ensures that set flags will not be cleared
while in break mode. This protection allows registers to be freely read
and written during break mode without losing status flag information.
Setting the BCFE bit enables the clearing mechanisms. Once cleared in
break mode, a flag remains cleared even when break mode is exited.
Status flags with a two-step clearing mechanism — for example, a read
of one register followed by the read or write of another — are protected,
even when the first step is accomplished prior to entering break mode.
Upon leaving break mode, execution of the second step will clear the flag
as normal.
Data Sheet
130
MC68HC908LD64 — Rev. 3.0
System Integration Module (SIM)
Freescale Semiconductor
System Integration Module (SIM)
Low-Power Modes
9.7 Low-Power Modes
Executing the WAIT or STOP instruction puts the MCU in a low-powerconsumption mode for standby situations. The SIM holds the CPU in a
non-clocked state. The operation of each of these modes is described
below. Both STOP and WAIT clear the interrupt mask (I) in the condition
code register, allowing interrupts to occur.
9.7.1 Wait Mode
In wait mode, the CPU clocks are inactive while the peripheral clocks
continue to run. Figure 9-14 shows the timing for wait mode entry.
A module that is active during wait mode can wake up the CPU with an
interrupt if the interrupt is enabled. Stacking for the interrupt begins one
cycle after the WAIT instruction during which the interrupt occurred. In
wait mode, the CPU clocks are inactive. Refer to the wait mode
subsection of each module to see if the module is active or inactive in
wait mode. Some modules can be programmed to be active in wait
mode.
Wait mode can also be exited by a reset or break. A break interrupt
during wait mode sets the SIM break stop/wait bit, SBSW, in the SIM
break status register (SBSR). If the COP disable bit, COPD, in
configuration register (CONFIG) is logic zero, then the computer
operating properly module (COP) is enabled and remains active in wait
mode.
IAB
IDB
WAIT ADDR
WAIT ADDR + 1
PREVIOUS DATA
NEXT OPCODE
SAME
SAME
SAME
SAME
R/W
NOTE: Previous data can be operand data or the WAIT opcode, depending on the last instruction.
Figure 9-14. Wait Mode Entry Timing
Figure 9-15 and Figure 9-16 show the timing for WAIT recovery.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
System Integration Module (SIM)
131
System Integration Module (SIM)
IAB
IDB
$6E0B
$A6
$A6
$6E0C
$A6
$00FF
$01
$0B
$00FE
$00FD
$00FC
$6E
EXITSTOPWAIT
NOTE: EXITSTOPWAIT = RST pin OR CPU interrupt OR break interrupt
Figure 9-15. Wait Recovery from Interrupt or Break
32
Cycles
$6E0B
IAB
IDB
$A6
$A6
32
Cycles
RST VCT H RST VCT L
$A6
RST
OSCXCLK
Figure 9-16. Wait Recovery from Internal Reset
9.7.2 Stop Mode
In stop mode, the SIM counter is reset and the system clocks are
disabled. An interrupt request from a module can cause an exit from stop
mode. Stacking for interrupts begins after the selected stop recovery
time has elapsed. Reset or break also causes an exit from stop mode.
The SIM disables the oscillator signals (OSCOUT and OSCXCLK) in
stop mode, stopping the CPU and peripherals. Stop recovery time is
selectable using the SSREC bit in configuration register (CONFIG). If
SSREC is set, stop recovery is reduced from the normal delay of 4096
OSCXCLK cycles down to 32. This is ideal for applications using canned
oscillators that do not require long start-up times from stop mode.
NOTE:
External crystal applications should use the full stop recovery time by
clearing the SSREC bit.
Data Sheet
132
MC68HC908LD64 — Rev. 3.0
System Integration Module (SIM)
Freescale Semiconductor
System Integration Module (SIM)
Low-Power Modes
A break interrupt during stop mode sets the SIM break stop/wait bit
(SBSW) in the SIM break status register (SBSR).
The SIM counter is held in reset from the execution of the STOP
instruction until the beginning of stop recovery. It is then used to time the
recovery period. Figure 9-17 shows stop mode entry timing.
CPUSTOP
IAB
IDB
STOP ADDR
STOP ADDR + 1
PREVIOUS DATA
SAME
NEXT OPCODE
SAME
SAME
SAME
R/W
NOTE: Previous data can be operand data or the STOP opcode, depending on the last instruction.
Figure 9-17. Stop Mode Entry Timing
STOP RECOVERY PERIOD
OSCXCLK
INT/BREAK
IAB
STOP +1
STOP + 2
STOP + 2
SP
SP – 1
SP – 2
SP – 3
Figure 9-18. Stop Mode Recovery from Interrupt or Break
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
System Integration Module (SIM)
133
System Integration Module (SIM)
9.8 SIM Registers
The SIM has three memory mapped registers. Table 9-4 shows the
mapping of these registers.
Table 9-4. SIM Registers Summary
Address
Register
Access Mode
$FE00
SBSR
User
$FE01
SRSR
User
$FE03
SBFCR
User
9.8.1 SIM Break Status Register (SBSR)
The SIM break status register contains a flag to indicate that a break
caused an exit from stop or wait mode.
Address:
$FE00
Bit 7
6
5
4
3
2
R
R
R
R
R
R
Read:
1
Bit 0
SBSW
R
Write:
Note
Reset:
0
Note: Writing a logic 0 clears SBSW.
R
= Reserved
Figure 9-19. SIM Break Status Register (SBSR)
SBSW — SIM Break Stop/Wait Bit
This status bit is useful in applications requiring a return to wait or stop
mode after exiting from a break interrupt. Clear SBSW by writing a
logic 0 to it. Reset clears SBSW.
1 = Stop mode or wait mode was exited by break interrupt
0 = Stop mode or wait mode was not exited by break interrupt
SBSW can be read within the break interrupt routine. The user can
modify the return address on the stack by subtracting one from it. The
following code is an example.
Data Sheet
134
MC68HC908LD64 — Rev. 3.0
System Integration Module (SIM)
Freescale Semiconductor
System Integration Module (SIM)
SIM Registers
; This code works if the H register has been pushed onto the stack in the break
; service routine software. This code should be executed at the end of the break
; service routine software.
HIBYTE
EQU
5
LOBYTE
EQU
6
;
If not SBSW, do RTI
BRCLR
SBSW,SBSR, RETURN
; See if wait mode or stop mode was exited by
; break.
TST
LOBYTE,SP
;If RETURNLO is not zero,
BNE
DOLO
;then just decrement low byte.
DEC
HIBYTE,SP
;Else deal with high byte, too.
DOLO
DEC
LOBYTE,SP
;Point to WAIT/STOP opcode.
RETURN
PULH
RTI
;Restore H register.
9.8.2 SIM Reset Status Register (SRSR)
This register contains six flags that show the source of the last reset.
Clear the SIM reset status register by reading it. A power-on reset sets
the POR bit and clears all other bits in the register.
Address:
Read:
$FE01
Bit 7
6
5
4
3
2
1
Bit 0
POR
PIN
COP
ILOP
ILAD
USB
0
0
1
0
0
0
0
0
0
0
Write:
POR:
= Unimplemented
Figure 9-20. SIM Reset Status Register (SRSR)
POR — Power-On Reset Bit
1 = Last reset caused by POR circuit
0 = Read of SRSR
PIN — External Reset Bit
1 = Last reset caused by external reset pin (RST)
0 = POR or read of SRSR
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
System Integration Module (SIM)
135
System Integration Module (SIM)
COP — Computer Operating Properly Reset Bit
1 = Last reset caused by COP counter
0 = POR or read of SRSR
ILOP — Illegal Opcode Reset Bit
1 = Last reset caused by an illegal opcode
0 = POR or read of SRSR
ILAD — Illegal Address Reset Bit (opcode fetches only)
1 = Last reset caused by an opcode fetch from an illegal address
0 = POR or read of SRSR
USB — Universal Serial Bus Reset Bit
1 = Last reset caused by an USB module
0 = POR or read of SRSR
9.8.3 SIM Break Flag Control Register (SBFCR)
The SIM break flag control register contains a bit that enables software
to clear status bits while the MCU is in a break state.
Address:
$FE03
Bit 7
6
5
4
3
2
1
Bit 0
BCFE
R
R
R
R
R
R
R
Read:
Write:
Reset:
0
R
= Reserved
Figure 9-21. SIM Break Flag Control Register (SBFCR)
BCFE — Break Clear Flag Enable Bit
This read/write bit enables software to clear status bits by accessing
status registers while the MCU is in a break state. To clear status bits
during the break state, the BCFE bit must be set.
1 = Status bits clearable during break
0 = Status bits not clearable during break
Data Sheet
136
MC68HC908LD64 — Rev. 3.0
System Integration Module (SIM)
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 10. Monitor ROM (MON)
10.1 Contents
10.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
10.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
10.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138
10.4.1 Entering Monitor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
10.4.2 Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
10.4.3 Echoing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
10.4.4 Break Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
10.4.5 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
10.4.6 Baud Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147
10.2 Introduction
This section describes the monitor ROM (MON) and the monitor mode
entry methods. The monitor ROM allows complete testing of the MCU
through a single-wire interface with a host computer. Monitor mode entry
can be achieved without use of the higher test voltage, VTST, as long as
vector addresses $FFFE and $FFFF are blank, thus reducing the
hardware requirements for in-circuit programming.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Monitor ROM (MON)
137
Monitor ROM (MON)
10.3 Features
Features of the monitor ROM include:
•
Normal user-mode pin functionality
•
One pin dedicated to serial communication between monitor ROM
and host computer
•
Standard mark/space non-return-to-zero (NRZ) communication
with host computer
•
Execution of code in RAM or FLASH
•
FLASH memory security feature1
•
FLASH memory programming interface
•
1024 bytes monitor ROM code size ($FA00 to $FDFF)
•
Monitor mode entry without high voltage, VTST, if reset vector is
blank ($FFFE and $FFFF contain $FF)
•
Standard monitor mode entry if high voltage, VTST, is applied to
IRQ
10.4 Functional Description
The monitor ROM receives and executes commands from a host
computer. Figure 10-1 shows a sample circuit used to enter monitor
mode and communicate with a host computer via a standard RS-232
interface.
Simple monitor commands can access any memory address. In monitor
mode, the MCU can execute code downloaded into RAM by a host
computer while most MCU pins retain normal operating mode functions.
All communication between the host computer and the MCU is through
the PTA0 pin. A level-shifting and multiplexing interface is required
between PTA0 and the host computer. PTA0 is used in a wired-OR
configuration and requires a pull-up resistor.
1. No security feature is absolutely secure. However, Freescale’s strategy is to make reading or
copying the FLASH difficult for unauthorized users.
Data Sheet
138
MC68HC908LD64 — Rev. 3.0
Monitor ROM (MON)
Freescale Semiconductor
Monitor ROM (MON)
Functional Description
VDD
68HC908LD64
10 kΩ
RST
0.1 µF
VTST
10 Ω
SW2
IRQ
C
(See NOTES) D
OSC1
X1
9.8304 MHz
20 pF
10 MΩ
OSC2
1
10 µF
+
MC145407
3
20
20 pF
+
VSS1
10 µF
VSS2
18
VSSA
4
10 µF
+
2
17
19
+
10 µF
VDD
VDD
VDD1
VDD2
0.1 µF
DB-25
2
5
16
3
6
15
VDD
VDDA
0.1 µF
DPLUS0
7
DMINUS0
VDD
1
MC74LCX125
2
3
6
5
PTD4/DDCSCL
VDD
14
PTD5/DDCSDA
10 kΩ
PTA0
4
VDD
VDD
7
10 kΩ
A
PTC3
10 kΩ
SW1
(See NOTES) B
PTC0
PTC1
PTA7
NOTES:
1. SW2: Position C — For monitor mode entry when IRQ = VTST:
SW1: Position A — Bus clock = OSCXCLK ÷ 4
SW1: Position B — Bus clock = OSCXCLK ÷ 2
2. SW2: Position D — For monitor mode entry when reset vector is blank ($FFFE and $FFFF = $FF):
Bus clock = OSCXCLK ÷ 4; PTC0, PTC1, and PTC3 voltages are not required.
3. See Table 24-4 for IRQ voltage level requirements.
Figure 10-1. Monitor Mode Circuit
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Monitor ROM (MON)
139
Monitor ROM (MON)
10.4.1 Entering Monitor Mode
Table 10-1 shows the pin conditions for entering monitor mode. As
specified in the table, monitor mode may be entered after a power-on
reset (POR) and will allow communication at 9600 baud provided one of
the following sets of conditions is met:
1. If monitor entry is by high voltage on IRQ (IRQ = VTST)
– The external clock is 4.9152 MHz with PTC3 low or
9.8304 MHz with PTC3 high
2. If monitor entry is by blank reset vector ($FFFE and $FFFF both
contain $FF; erased state):
– The external clock is 9.8304 MHz
NOTE:
Holding the PTC3 pin low when entering monitor mode by a high voltage
causes a bypass of a divide-by-two stage at the oscillator. The OSCOUT
frequency is equal to the OSCXCLK frequency, and the OSC1 input
directly generates internal bus clocks. In this case, the OSC1 signal
must have a 50% duty cycle at maximum bus frequency.
NOTE:
If the reset vector is blank and monitor mode is entered, the chip will see
an additional reset cycle after the initial POR reset. Once the part has
been programmed, the traditional method of applying a high voltage,
VTST, to IRQ must be used to enter monitor mode.
Enter monitor mode with the pin configuration shown in Table 10-1 after
a reset. The rising edge of reset latches monitor mode. Once monitor
mode is latched, the values on the specified pins can change.
Once out of reset, the MCU monitor mode firmware then sends a break
signal (10 consecutive logic zeros) to the host computer, indicating that
it is ready to receive a command. The break signal also provides a timing
reference to allow the host to determine the necessary baud rate.
Data Sheet
140
MC68HC908LD64 — Rev. 3.0
Monitor ROM (MON)
Freescale Semiconductor
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Table 10-1. Monitor Mode Signal Requirements and Options
Monitor ROM (MON)
IRQ
RST
Address
$FFFE/
$FFFF
PTC3
PTC1
PTC0
PTA7(1)
DPLUS0
DMINUS0
PTD4
PTD5
External
Clock(2)
Bus
Frequency
COP
Baud
Rate
X
GND
X
X
X
X
X
X
X
0
Disabled
0
VTST
VDD
or
VTST
X
0
0
1
0
0
4.9152
MHz
2.4576
MHz
Disabled
9600
Enters monitor mode.
PTC0, PTC1, and PTC3
voltages only required if
IRQ = VTST;
PTC3 determines
frequency divider.
Exit monitor mode by POR
or by RST low then high
VTST
VDD
or
VTST
X
1
0
1
0
0
9.8304
MHz
2.4576
MHz
Disabled
9600
Enters monitor mode.
PTC0, PTC1, and PTC3
voltages only required if
IRQ = VTST;
PTC3 determines
frequency divider.
Exit monitor mode by POR
or by RST low then high
VDD
or
GND
VDD
Blank
"$FFFF"
X
X
X
0
0
9.8304
MHz
2.4576
MHz
Disabled
9600
Enters monitor mode.
External frequency always
divided by 4.
Exit monitor mode by POR
only.
VDD
or
GND
VDD
Not Blank
X
X
X
X
X
X
—
Enabled
—
Comment
No operation until
reset goes high.
Enters user mode.
Notes:
Data Sheet
141
Monitor ROM (MON)
Functional Description
1. PTA7 = 0 if serial communication; PTA7 = 1 if parallel communication
2. External clock is derived by a 4.9152/9.8304 MHz crystal or off-chip oscillator
Monitor ROM (MON)
Monitor mode uses different vectors for reset and SWI. The alternate
vectors are in the $FE page instead of the $FF page and allow code
execution from the internal monitor firmware instead of user code.
When the host computer has completed downloading code into the MCU
RAM, This code can be executed by driving PTA0 low while asserting
RST low and then high. The internal monitor ROM firmware will interpret
the low on PTA0 as an indication to jump to RAM, and execution control
will then continue from RAM. Execution of an SWI from the downloaded
code will return program control to the internal monitor ROM firmware.
Alternatively, the host can send a RUN command, which executes an
RTI, and this can be used to send control to the address on the stack
pointer.
The COP module is disabled in monitor mode as long as VTST is applied
to the IRQ or the RST pin. (See Section 9. System Integration Module
(SIM) for more information on modes of operation.)
Table 10-2 is a summary of the differences between user mode and
monitor mode.
Table 10-2. Mode Differences
Functions
COP
Reset
Vector
High
Reset
Vector
Low
SWI
Vector
High
SWI
Vector
Low
User
Enabled
$FFFE
$FFFF
$FFFC
$FFFD
Monitor
Disabled (1)
$FEFE
$FEFF
$FEFC
$FEFD
Modes
Notes:
1. If the high voltage (VTST) is removed from the IRQ pin, the SIM asserts its COP enable
output. The COP is an option enabled or disabled by the COPD bit in the configuration
register.
10.4.2 Data Format
Communication with the monitor ROM is in standard non-return-to-zero
(NRZ) mark/space data format. (See Figure 10-2 and Figure 10-3.)
Data Sheet
142
MC68HC908LD64 — Rev. 3.0
Monitor ROM (MON)
Freescale Semiconductor
Monitor ROM (MON)
Functional Description
START
BIT
BIT 0
BIT 1
BIT 2
BIT 3
BIT 4
BIT 5
BIT 6
STOP
BIT
BIT 7
NEXT
START
BIT
Figure 10-2. Monitor Data Format
$A5
START
BIT
BIT 0
BIT 1
BIT 2
BIT 3
BIT 4
BIT 5
BIT 6
BIT 7
BREAK
START
BIT
BIT 0
BIT 1
BIT 2
BIT 3
BIT 4
BIT 5
BIT 6
BIT 7
STOP
BIT
NEXT
START
BIT
STOP
BIT
Figure 10-3. Sample Monitor Waveforms
The data transmit and receive rate can be anywhere from 4800 baud to
28.8 kbaud. Transmit and receive baud rates must be identical.
10.4.3 Echoing
As shown in Figure 10-4, the monitor ROM immediately echoes each
received byte back to the PTA0 pin for error checking.
SENT TO
MONITOR
READ
READ
ADDR. HIGH ADDR. HIGH ADDR. LOW
ECHO
ADDR. LOW
DATA
RESULT
Figure 10-4. Read Transaction
Any result of a command appears after the echo of the last byte of the
command.
10.4.4 Break Signal
A start bit followed by nine low bits is a break signal (see Figure 10-5).
When the monitor receives a break signal, it drives the PTA0 pin high for
the duration of two bits before echoing the break signal.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Monitor ROM (MON)
143
Monitor ROM (MON)
MISSING STOP BIT
TWO-STOP-BIT DELAY BEFORE ZERO ECHO
0
1
2
3
4
5
6
0
7
1
2
3
4
5
6
7
Figure 10-5. Break Transaction
10.4.5 Commands
The monitor ROM uses the following commands:
•
READ (read memory)
•
WRITE (write memory)
•
IREAD (indexed read)
•
IWRITE (indexed write)
•
READSP (read stack pointer)
•
RUN (run user program)
Table 10-3. READ (Read Memory) Command
Description
Read byte from memory
Operand
Specifies 2-byte address in high byte:low byte order
Data
Returned
Returns contents of specified address
Opcode
$4A
Command Sequence
SENT TO
MONITOR
READ
READ
ADDRESS
HIGH
ADDRESS
HIGH
ECHO
ADDRESS
LOW
DATA
RETURN
Data Sheet
144
ADDRESS
LOW
MC68HC908LD64 — Rev. 3.0
Monitor ROM (MON)
Freescale Semiconductor
Monitor ROM (MON)
Functional Description
Table 10-4. WRITE (Write Memory) Command
Description
Write byte to memory
Operand
Specifies 2-byte address in high byte:low byte order; low byte
followed by data byte
Data
Returned
None
Opcode
$49
Command Sequence
SENT TO
MONITOR
WRITE
WRITE
ADDRESS
HIGH
ADDRESS
HIGH
ADDRESS
LOW
ADDRESS
LOW
DATA
DATA
ECHO
Table 10-5. IREAD (Indexed Read) Command
Description
Read Next 2 Bytes in Memory from Last Address Accessed
Operand
Specifies 2-byte address in high byte:low byte order
Data
Returned
Returns contents of next two addresses
Opcode
$1A
Command Sequence
SENT TO
MONITOR
IREAD
IREAD
ECHO
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
DATA
DATA
RETURN
Data Sheet
Monitor ROM (MON)
145
Monitor ROM (MON)
Table 10-6. IWRITE (Indexed Write) Command
Description
Write to last address accessed + 1
Operand
Specifies single data byte
Data
Returned
None
Opcode
$19
Command Sequence
SENT TO
MONITOR
IWRITE
IWRITE
DATA
DATA
ECHO
A sequence of IREAD or IWRITE commands can sequentially access a
block of memory over the full 64K-byte memory map.
Table 10-7. READSP (Read Stack Pointer) Command
Description
Reads stack pointer
Operand
None
Data
Returned
Returns stack pointer in high byte:low byte order
Opcode
$0C
Command Sequence
SENT TO
MONITOR
READSP
READSP
ECHO
Data Sheet
146
SP
HIGH
SP
LOW
RETURN
MC68HC908LD64 — Rev. 3.0
Monitor ROM (MON)
Freescale Semiconductor
Monitor ROM (MON)
Functional Description
Table 10-8. RUN (Run User Program) Command
Description
Executes RTI instruction
Operand
None
Data
Returned
None
Opcode
$28
Command Sequence
SENT TO
MONITOR
RUN
RUN
ECHO
10.4.6 Baud Rate
The communication baud rate is controlled by crystal frequency and the
state of the PTC3 pin upon entry into monitor mode. When PTC3 is high,
the divide by ratio is 1024. If the PTC3 pin is at logic zero upon entry into
monitor mode, the divide by ratio is 512.
Table 10-9. Monitor Baud Rate Selection
Crystal Frequency
PTC3 Pin
Baud Rate
9.8304 MHz
0
19200 bps
9.8304 MHz
1
9600 bps
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Monitor ROM (MON)
147
Monitor ROM (MON)
Data Sheet
148
MC68HC908LD64 — Rev. 3.0
Monitor ROM (MON)
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 11. Timer Interface Module (TIM)
11.1 Contents
11.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
11.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
11.4
Pin Name Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
11.5 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .151
11.5.1 TIM Counter Prescaler . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
11.5.2 Input Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
11.5.3 Output Compare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
11.5.3.1
Unbuffered Output Compare . . . . . . . . . . . . . . . . . . . . . 154
11.5.3.2
Buffered Output Compare . . . . . . . . . . . . . . . . . . . . . . .155
11.5.4 Pulse Width Modulation (PWM) . . . . . . . . . . . . . . . . . . . . . 155
11.5.4.1
Unbuffered PWM Signal Generation . . . . . . . . . . . . . . . 156
11.5.4.2
Buffered PWM Signal Generation . . . . . . . . . . . . . . . . . 157
11.5.4.3
PWM Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
11.6
Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159
11.7 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
11.7.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159
11.7.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160
11.8
TIM During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . 160
11.9
I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
11.10 I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
11.10.1 TIM Status and Control Register (TSC) . . . . . . . . . . . . . . . 161
11.10.2 TIM Counter Registers (TCNTH:TCNTL) . . . . . . . . . . . . . . 163
11.10.3 TIM Counter Modulo Registers (TMODH:TMODL) . . . . . . 164
11.10.4 TIM Channel Status and Control Registers (TSC0:TSC1) . 165
11.10.5 TIM Channel Registers (TCH0H/L:TCH1H/L) . . . . . . . . . . 168
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Timer Interface Module (TIM)
149
Timer Interface Module (TIM)
11.2 Introduction
This section describes the timer interface module (TIM2, Version B). The
TIM is a two-channel timer that provides a timing reference with input
capture, output compare, and pulse-width-modulation functions.
Figure 11-1 is a block diagram of the TIM.
11.3 Features
Features of the TIM include the following:
NOTE:
•
Two input capture/output compare channels
– Rising-edge, falling-edge, or any-edge input capture trigger
– Set, clear, or toggle output compare action
•
Buffered and unbuffered pulse width modulation (PWM) signal
generation
•
Programmable TIM clock input
– Seven-frequency internal bus clock prescaler selection
•
Free-running or modulo up-count operation
•
Toggle any channel pin on overflow
•
TIM counter stop and reset bits
TCH1 (timer channel 1) is not bonded to an external pin on this MCU.
Therefore, any references to the timer TCH1 pin in the following text
should be interpreted as not available — but the internal status and
control registers are still available.
11.4 Pin Name Conventions
The TIM shares the TCH0 pin with the sync processor CLAMP output.
Table 11-1. Pin Name Conventions
TIM Generic Pin Name:
TCH0
Full TIM Pin Name:
CLAMP/TCH0
Pin Selected for TCH0 By:
ELS0B:ELS0A
Data Sheet
150
MC68HC908LD64 — Rev. 3.0
Timer Interface Module (TIM)
Freescale Semiconductor
Timer Interface Module (TIM)
Functional Description
11.5 Functional Description
Figure 11-1 shows the structure of the TIM. The central component of
the TIM is the 16-bit TIM counter that can operate as a free-running
counter or a modulo up-counter. The TIM counter provides the timing
reference for the input capture and output compare functions. The TIM
counter modulo registers, TMODH:TMODL, control the modulo value of
the TIM counter. Software can read the TIM counter value at any time
without affecting the counting sequence.
The two TIM channels are programmable independently as input
capture or output compare channels.
PRESCALER SELECT
INTERNAL
BUS CLOCK
PRESCALER
TSTOP
PS2
TRST
PS1
PS0
16-BIT COUNTER
TOF
TOIE
INTERRUPT
LOGIC
16-BIT COMPARATOR
TMODH:TMODL
TOV0
CHANNEL 0
ELS0B
ELS0A
CH0MAX
16-BIT COMPARATOR
TCH0H:TCH0L
PORT
LOGIC
TCH0
CH0F
INTERRUPT
LOGIC
16-BIT LATCH
MS0A
CH0IE
MS0B
INTERNAL BUS
TOV1
CHANNEL 1
ELS1B
ELS1A
CH1MAX
PORT
LOGIC
16-BIT COMPARATOR
TCH1
(Not available)
TCH1H:TCH1L
CH1F
INTERRUPT
LOGIC
16-BIT LATCH
MS1A
CH1IE
Figure 11-1. TIM Block Diagram
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Timer Interface Module (TIM)
151
Timer Interface Module (TIM)
Addr.
$000A
Register Name
Bit 7
6
5
TOIE
TSTOP
4
3
0
0
1
Bit 0
PS2
PS1
PS0
Read:
TIM Status and Control
Register Write:
(TSC)
Reset:
TOF
0
0
1
0
0
0
0
0
Read:
TIM Counter
Register High Write:
(TCNTH)
Reset:
Bit15
Bit14
Bit13
Bit12
Bit11
Bit10
Bit9
Bit8
0
0
0
0
0
0
0
0
Read:
TIM Counter
Register Low Write:
(TCNTL)
Reset:
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
0
0
0
0
0
0
0
0
Bit15
Bit14
Bit13
Bit12
Bit11
Bit10
Bit9
Bit8
1
1
1
1
1
1
1
1
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
1
1
1
1
1
1
1
1
CH0IE
MS0B
MS0A
ELS0B
ELS0A
TOV0
CH0MAX
0
0
0
0
0
0
0
0
Bit15
Bit14
Bit13
Bit12
Bit11
Bit10
Bit9
Bit8
Bit2
Bit1
Bit0
$000C
$000D
$000E
$000F
$0010
$0011
$0012
$0013
Read:
TIM Counter Modulo
Register High Write:
(TMODH)
Reset:
Read:
TIM Counter Modulo
Register Low Write:
(TMODL)
Reset:
TIM Channel 0 Read:
Status and Control
Write:
Register
(TSC0) Reset:
Read:
TIM Channel 0
Register High Write:
(TCH0H)
Reset:
Read:
TIM Channel 0
Register Low Write:
(TCH0L)
Reset:
TIM Channel 1 Read:
Status and Control
Write:
Register
(TSC1) Reset:
0
TRST
CH0F
0
Indeterminate after reset
Bit7
Bit6
Bit5
Bit4
Bit3
Indeterminate after reset
CH1F
0
CH1IE
MS1A
ELS1B
ELS1A
TOV1
CH1MAX
0
0
0
0
0
0
0
0
0
Data Sheet
152
2
MC68HC908LD64 — Rev. 3.0
Timer Interface Module (TIM)
Freescale Semiconductor
Timer Interface Module (TIM)
Functional Description
Addr.
$0014
$0015
Register Name
Read:
TIM Channel 1
Register High Write:
(TCH1H)
Reset:
Read:
TIM Channel 1
Register Low Write:
(TCH1L)
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
Bit15
Bit14
Bit13
Bit12
Bit11
Bit10
Bit9
Bit8
Bit2
Bit1
Bit0
Indeterminate after reset
Bit7
Bit6
Bit5
Bit4
Bit3
Indeterminate after reset
= Unimplemented
11.5.1 TIM Counter Prescaler
The TIM clock source can be one of the seven prescaler outputs. The
prescaler generates seven clock rates from the internal bus clock. The
prescaler select bits, PS[2:0], in the TIM status and control register
(TSC) select the TIM clock source.
11.5.2 Input Capture
With the input capture function, the TIM can capture the time at which an
external event occurs. When an active edge occurs on the pin of an input
capture channel, the TIM latches the contents of the TIM counter into the
TIM channel registers, TCHxH:TCHxL. The polarity of the active edge is
programmable. Input captures can generate TIM CPU interrupt
requests.
11.5.3 Output Compare
With the output compare function, the TIM can generate a periodic pulse
with a programmable polarity, duration, and frequency. When the
counter reaches the value in the registers of an output compare channel,
the TIM can set, clear, or toggle the channel pin. Output compares can
generate TIM CPU interrupt requests.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Timer Interface Module (TIM)
153
Timer Interface Module (TIM)
11.5.3.1 Unbuffered Output Compare
Any output compare channel can generate unbuffered output compare
pulses as described in 11.5.3 Output Compare. The pulses are
unbuffered because changing the output compare value requires writing
the new value over the old value currently in the TIM channel registers.
An unsynchronized write to the TIM channel registers to change an
output compare value could cause incorrect operation for up to two
counter overflow periods. For example, writing a new value before the
counter reaches the old value but after the counter reaches the new
value prevents any compare during that counter overflow period. Also,
using a TIM overflow interrupt routine to write a new, smaller output
compare value may cause the compare to be missed. The TIM may pass
the new value before it is written.
Use the following methods to synchronize unbuffered changes in the
output compare value on channel x:
•
When changing to a smaller value, enable channel x output
compare interrupts and write the new value in the output compare
interrupt routine. The output compare interrupt occurs at the end
of the current output compare pulse. The interrupt routine has until
the end of the counter overflow period to write the new value.
•
When changing to a larger output compare value, enable TIM
overflow interrupts and write the new value in the TIM overflow
interrupt routine. The TIM overflow interrupt occurs at the end of
the current counter overflow period. Writing a larger value in an
output compare interrupt routine (at the end of the current pulse)
could cause two output compares to occur in the same counter
overflow period.
Data Sheet
154
MC68HC908LD64 — Rev. 3.0
Timer Interface Module (TIM)
Freescale Semiconductor
Timer Interface Module (TIM)
Functional Description
11.5.3.2 Buffered Output Compare
Channels 0 and 1 can be linked to form a buffered output compare
channel whose output appears on the TCH0 pin. The TIM channel
registers of the linked pair alternately control the output.
Setting the MS0B bit in TIM channel 0 status and control register (TSC0)
links channel 0 and channel 1. The output compare value in the TIM
channel 0 registers initially controls the output on the TCH0 pin. Writing
to the TIM channel 1 registers enables the TIM channel 1 registers to
synchronously control the output after the TIM overflows. At each
subsequent overflow, the TIM channel registers (0 or 1) that control the
output are the ones written to last. TSC0 controls and monitors the
buffered output compare function, and TIM channel 1 status and control
register (TSC1) is unused.
NOTE:
In buffered output compare operation, do not write new output compare
values to the currently active channel registers. User software should
track the currently active channel to prevent writing a new value to the
active channel. Writing to the active channel registers is the same as
generating unbuffered output compares.
11.5.4 Pulse Width Modulation (PWM)
By using the toggle-on-overflow feature with an output compare channel,
the TIM can generate a PWM signal. The value in the TIM counter
modulo registers determines the period of the PWM signal. The channel
pin toggles when the counter reaches the value in the TIM counter
modulo registers. The time between overflows is the period of the PWM
signal.
As Figure 11-2 shows, the output compare value in the TIM channel
registers determines the pulse width of the PWM signal. The time
between overflow and output compare is the pulse width. Program the
TIM to clear the channel pin on output compare if the state of the PWM
pulse is logic one. Program the TIM to set the pin if the state of the PWM
pulse is logic zero.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Timer Interface Module (TIM)
155
Timer Interface Module (TIM)
OVERFLOW
OVERFLOW
OVERFLOW
PERIOD
PULSE
WIDTH
TCHx
OUTPUT
COMPARE
OUTPUT
COMPARE
OUTPUT
COMPARE
Figure 11-2. PWM Period and Pulse Width
The value in the TIM counter modulo registers and the selected
prescaler output determines the frequency of the PWM output. The
frequency of an 8-bit PWM signal is variable in 256 increments. Writing
$00FF (255) to the TIM counter modulo registers produces a PWM
period of 256 times the internal bus clock period if the prescaler select
value is 000 (see 11.10.1 TIM Status and Control Register (TSC)).
The value in the TIM channel registers determines the pulse width of the
PWM output. The pulse width of an 8-bit PWM signal is variable in 256
increments. Writing $0080 (128) to the TIM channel registers produces
a duty cycle of 128/256 or 50%.
11.5.4.1 Unbuffered PWM Signal Generation
Any output compare channel can generate unbuffered PWM pulses as
described in 11.5.4 Pulse Width Modulation (PWM). The pulses are
unbuffered because changing the pulse width requires writing the new
pulse width value over the old value currently in the TIM channel
registers.
An unsynchronized write to the TIM channel registers to change a pulse
width value could cause incorrect operation for up to two PWM periods.
For example, writing a new value before the counter reaches the old
value but after the counter reaches the new value prevents any compare
during that PWM period. Also, using a TIM overflow interrupt routine to
write a new, smaller pulse width value may cause the compare to be
missed. The TIM may pass the new value before it is written.
Data Sheet
156
MC68HC908LD64 — Rev. 3.0
Timer Interface Module (TIM)
Freescale Semiconductor
Timer Interface Module (TIM)
Functional Description
Use the following methods to synchronize unbuffered changes in the
PWM pulse width on channel x:
NOTE:
•
When changing to a shorter pulse width, enable channel x output
compare interrupts and write the new value in the output compare
interrupt routine. The output compare interrupt occurs at the end
of the current pulse. The interrupt routine has until the end of the
PWM period to write the new value.
•
When changing to a longer pulse width, enable TIM overflow
interrupts and write the new value in the TIM overflow interrupt
routine. The TIM overflow interrupt occurs at the end of the current
PWM period. Writing a larger value in an output compare interrupt
routine (at the end of the current pulse) could cause two output
compares to occur in the same PWM period.
In PWM signal generation, do not program the PWM channel to toggle
on output compare. Toggling on output compare prevents reliable 0%
duty cycle generation and removes the ability of the channel to selfcorrect in the event of software error or noise. Toggling on output
compare also can cause incorrect PWM signal generation when
changing the PWM pulse width to a new, much larger value.
11.5.4.2 Buffered PWM Signal Generation
Channels 0 and 1 can be linked to form a buffered PWM channel whose
output appears on the TCH0 pin. The TIM channel registers of the linked
pair alternately control the pulse width of the output.
Setting the MS0B bit in TIM channel 0 status and control register (TSC0)
links channel 0 and channel 1. The TIM channel 0 registers initially
control the pulse width on the TCH0 pin. Writing to the TIM channel 1
registers enables the TIM channel 1 registers to synchronously control
the pulse width at the beginning of the next PWM period. At each
subsequent overflow, the TIM channel registers (0 or 1) that control the
pulse width are the ones written to last. TSC0 controls and monitors the
buffered PWM function, and TIM channel 1 status and control register
(TSC1) is unused. While the MS0B bit is set, the channel 1 pin, TCH1,
is available as a general-purpose I/O pin.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Timer Interface Module (TIM)
157
Timer Interface Module (TIM)
NOTE:
In buffered PWM signal generation, do not write new pulse width values
to the currently active channel registers. User software should track the
currently active channel to prevent writing a new value to the active
channel. Writing to the active channel registers is the same as
generating unbuffered PWM signals.
11.5.4.3 PWM Initialization
To ensure correct operation when generating unbuffered or buffered
PWM signals, use the following initialization procedure:
1. In the TIM status and control register (TSC):
a. Stop the TIM counter by setting the TIM stop bit, TSTOP.
b. Reset the TIM counter and prescaler by setting the TIM reset
bit, TRST.
2. In the TIM counter modulo registers (TMODH:TMODL), write the
value for the required PWM period.
3. In the TIM channel x registers (TCHxH:TCHxL), write the value for
the required pulse width.
4. In TIM channel x status and control register (TSCx):
a. Write 0:1 (for unbuffered output compare or PWM signals) or
1:0 (for buffered output compare or PWM signals) to the
mode select bits, MSxB:MSxA. (See Table 11-3.)
b. Write 1 to the toggle-on-overflow bit, TOVx.
c. Write 1:0 (to clear output on compare) or 1:1 (to set output on
compare) to the edge/level select bits, ELSxB:ELSxA. The
output action on compare must force the output to the
complement of the pulse width level. (See Table 11-3.)
NOTE:
In PWM signal generation, do not program the PWM channel to toggle
on output compare. Toggling on output compare prevents reliable 0%
duty cycle generation and removes the ability of the channel to selfcorrect in the event of software error or noise. Toggling on output
compare can also cause incorrect PWM signal generation when
changing the PWM pulse width to a new, much larger value.
5. In the TIM status control register (TSC), clear the TIM stop bit,
TSTOP.
Data Sheet
158
MC68HC908LD64 — Rev. 3.0
Timer Interface Module (TIM)
Freescale Semiconductor
Timer Interface Module (TIM)
Interrupts
Setting MS0B links channels 0 and 1 and configures them for buffered
PWM operation. The TIM channel 0 registers (TCH0H:TCH0L) initially
control the buffered PWM output.TIM channel 0 status and control
register (TSC0) controls and monitors the PWM signal from the linked
channels.
Clearing the toggle-on-overflow bit, TOVx, inhibits output toggles on TIM
overflows. Subsequent output compares try to force the output to a state
it is already in and have no effect. The result is a 0% duty cycle output.
Setting the channel x maximum duty cycle bit (CHxMAX) and setting the
TOVx bit generates a 100% duty cycle output. See 11.10.4 TIM Channel
Status and Control Registers (TSC0:TSC1).
11.6 Interrupts
The following TIM sources can generate interrupt requests:
•
TIM overflow flag (TOF) — The TOF bit is set when the TIM
counter reaches the modulo value programmed in the TIM counter
modulo registers. The TIM overflow interrupt enable bit, TOIE,
enables TIM overflow CPU interrupt requests. TOF and TOIE are
in the TIM status and control register.
•
TIM channel flags (CH1F:CH0F) — The CHxF bit is set when an
input capture or output compare occurs on channel x. Channel x
TIM CPU interrupt requests are controlled by the channel x
interrupt enable bit, CHxIE. Channel x TIM CPU interrupt requests
are enabled when CHxIE=1. CHxF and CHxIE are in the TIM
channel x status and control register.
11.7 Low-Power Modes
The WAIT and STOP instructions puts the MCU in low-powerconsumption standby modes.
11.7.1 Wait Mode
The TIM remains active after the execution of a WAIT instruction. In wait
mode the TIMA registers are not accessible by the CPU. Any enabled
CPU interrupt request from the TIM can bring the MCU out of wait mode.
If TIM functions are not required during wait mode, reduce power
consumption by stopping the TIM before executing the WAIT instruction.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Timer Interface Module (TIM)
159
Timer Interface Module (TIM)
11.7.2 Stop Mode
The TIM is inactive after the execution of a STOP instruction. The STOP
instruction does not affect register conditions or the state of the TIM
counter. TIM operation resumes when the MCU exit stop mode after an
external interrupt.
11.8 TIM During Break Interrupts
A break interrupt stops the TIM counter.
The system integration module (SIM) controls whether status bits in
other modules can be cleared during the break state. The BCFE bit in
the break flag control register (BFCR) enables software to clear status
bits during the break state. (See 23.6.4 SIM Break Flag Control
Register.)
To allow software to clear status bits during a break interrupt, write a
logic one to the BCFE bit. If a status bit is cleared during the break state,
it remains cleared when the MCU exits the break state.
To protect status bits during the break state, write a logic zero to the
BCFE bit. With BCFE at logic zero (its default state), software can read
and write I/O registers during the break state without affecting status
bits. Some status bits have a two-step read/write clearing procedure. If
software does the first step on such a bit before the break, the bit cannot
change during the break state as long as BCFE is at logic zero. After the
break, doing the second step clears the status bit.
11.9 I/O Signals
The TIM channel I/O pin is CLAMP/TCH0. The pin is shared with sync
processor CLAMP output signal.
TCH0 pin is programmable independently as an input capture pin or an
output compare pin. It also can be configured as a buffered output
compare or buffered PWM pin.
Data Sheet
160
MC68HC908LD64 — Rev. 3.0
Timer Interface Module (TIM)
Freescale Semiconductor
Timer Interface Module (TIM)
I/O Registers
11.10 I/O Registers
The following I/O registers control and monitor operation of the TIM:
•
TIM status and control register (TSC)
•
TIM counter registers (TCNTH:TCNTL)
•
TIM counter modulo registers (TMODH:TMODL)
•
TIM channel status and control registers (TSC0 and TSC1)
•
TIM channel registers (TCH0H:TCH0L and TCH1H:TCH1L)
11.10.1 TIM Status and Control Register (TSC)
The TIM status and control register does the following:
•
Enables TIM overflow interrupts
•
Flags TIM overflows
•
Stops the TIM counter
•
Resets the TIM counter
•
Prescales the TIM counter clock
Address:
$000A
Bit 7
Read:
6
5
TOIE
TSTOP
TOF
Write:
0
Reset:
0
4
3
0
0
2
1
Bit 0
PS2
PS1
PS0
0
0
0
TRST
0
1
0
0
= Unimplemented
Figure 11-3. TIM Status and Control Register (TSC)
TOF — TIM Overflow Flag Bit
This read/write flag is set when the TIM counter reaches the modulo
value programmed in the TIM counter modulo registers. Clear TOF by
reading the TIM status and control register when TOF is set and then
writing a logic zero to TOF. If another TIM overflow occurs before the
clearing sequence is complete, then writing logic zero to TOF has no
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Timer Interface Module (TIM)
161
Timer Interface Module (TIM)
effect. Therefore, a TOF interrupt request cannot be lost due to
inadvertent clearing of TOF. Reset clears the TOF bit. Writing a logic
one to TOF has no effect.
1 = TIM counter has reached modulo value
0 = TIM counter has not reached modulo value
TOIE — TIM Overflow Interrupt Enable Bit
This read/write bit enables TIM overflow interrupts when the TOF bit
becomes set. Reset clears the TOIE bit.
1 = TIM overflow interrupts enabled
0 = TIM overflow interrupts disabled
TSTOP — TIM Stop Bit
This read/write bit stops the TIM counter. Counting resumes when
TSTOP is cleared. Reset sets the TSTOP bit, stopping the TIM
counter until software clears the TSTOP bit.
1 = TIM counter stopped
0 = TIM counter active
NOTE:
Do not set the TSTOP bit before entering wait mode if the TIM is required
to exit wait mode.
TRST — TIM Reset Bit
Setting this write-only bit resets the TIM counter and the TIM
prescaler. Setting TRST has no effect on any other registers.
Counting resumes from $0000. TRST is cleared automatically after
the TIM counter is reset and always reads as logic zero. Reset clears
the TRST bit.
1 = Prescaler and TIM counter cleared
0 = No effect
NOTE:
Setting the TSTOP and TRST bits simultaneously stops the TIM counter
at a value of $0000.
PS[2:0] — Prescaler Select Bits
These read/write bits select either the TCLK pin or one of the seven
prescaler outputs as the input to the TIM counter as Table 11-2
shows. Reset clears the PS[2:0] bits.
Data Sheet
162
MC68HC908LD64 — Rev. 3.0
Timer Interface Module (TIM)
Freescale Semiconductor
Timer Interface Module (TIM)
I/O Registers
Table 11-2. Prescaler Selection
PS2
PS1
PS0
TIM Clock Source
0
0
0
Internal Bus Clock ÷ 1
0
0
1
Internal Bus Clock ÷ 2
0
1
0
Internal Bus Clock ÷ 4
0
1
1
Internal Bus Clock ÷ 8
1
0
0
Internal Bus Clock ÷ 16
1
0
1
Internal Bus Clock ÷ 32
1
1
0
Internal Bus Clock ÷ 64
1
1
1
Not available
11.10.2 TIM Counter Registers (TCNTH:TCNTL)
The two read-only TIM counter registers contain the high and low bytes
of the value in the TIM counter. Reading the high byte (TCNTH) latches
the contents of the low byte (TCNTL) into a buffer. Subsequent reads of
TCNTH do not affect the latched TCNTL value until TCNTL is read.
Reset clears the TIM counter registers. Setting the TIM reset bit (TRST)
also clears the TIM counter registers.
Address:
Read:
$000C
TCNTH
Bit 7
6
5
4
3
2
1
Bit 0
Bit15
Bit14
Bit13
Bit12
Bit11
Bit10
Bit9
Bit8
0
0
0
0
0
0
0
0
$000D
TCNTL
Bit 7
6
5
4
3
2
1
Bit 0
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
0
0
0
0
0
0
0
0
Write:
Reset:
Address:
Read:
Write:
Reset:
= Unimplemented
Figure 11-4. TIM Counter Registers (TCNTH:TCNTL)
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Timer Interface Module (TIM)
163
Timer Interface Module (TIM)
NOTE:
If you read TCNTH during a break interrupt, be sure to unlatch TCNTL
by reading TCNTL before exiting the break interrupt. Otherwise, TCNTL
retains the value latched during the break.
11.10.3 TIM Counter Modulo Registers (TMODH:TMODL)
The read/write TIM modulo registers contain the modulo value for the
TIM counter. When the TIM counter reaches the modulo value, the
overflow flag (TOF) becomes set, and the TIM counter resumes counting
from $0000 at the next timer clock. Writing to the high byte (TMODH)
inhibits the TOF bit and overflow interrupts until the low byte (TMODL) is
written. Reset sets the TIM counter modulo registers.
Address:
$000E
TMODH
Bit 7
6
5
4
3
2
1
Bit 0
Bit15
Bit14
Bit13
Bit12
Bit11
Bit10
Bit9
Bit8
1
1
1
1
1
1
1
1
$000F
TMODL
Bit 7
6
5
4
3
2
1
Bit 0
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
1
1
1
1
1
1
1
1
Read:
Write:
Reset:
Address:
Read:
Write:
Reset:
Figure 11-5. TIM Counter Modulo Registers (TMODH:TMODL)
NOTE:
Reset the TIM counter before writing to the TIM counter modulo registers.
Data Sheet
164
MC68HC908LD64 — Rev. 3.0
Timer Interface Module (TIM)
Freescale Semiconductor
Timer Interface Module (TIM)
I/O Registers
11.10.4 TIM Channel Status and Control Registers (TSC0:TSC1)
Each of the TIM channel status and control registers does the following:
•
Flags input captures and output compares
•
Enables input capture and output compare interrupts
•
Selects input capture, output compare, or PWM operation
•
Selects high, low, or toggling output on output compare
•
Selects rising edge, falling edge, or any edge as the active input
capture trigger
•
Selects output toggling on TIM overflow
•
Selects 0% and 100% PWM duty cycle
•
Selects buffered or unbuffered output compare/PWM operation
Address:
$0010
TSC0
Bit 7
6
5
4
3
2
1
Bit 0
CH0IE
MS0B
MS0A
ELS0B
ELS0A
TOV0
CH0MAX
0
0
0
0
0
0
5
4
3
2
1
Bit 0
MS1A
ELS1B
ELS1A
TOV1
CH1MAX
0
0
0
0
0
Read:
CH0F
Write:
0
Reset:
0
0
$0013
TSC1
Bit 7
6
Address:
Read:
CH1F
0
CH1IE
Write:
0
Reset:
0
0
0
= Unimplemented
Figure 11-6. TIM Channel Status and Control Registers (TSC0:TSC1)
CHxF — Channel x Flag Bit
When channel x is an input capture channel, this read/write bit is set
when an active edge occurs on the channel x pin. When channel x is
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Timer Interface Module (TIM)
165
Timer Interface Module (TIM)
an output compare channel, CHxF is set when the value in the TIM
counter registers matches the value in the TIM channel x registers.
When TIM CPU interrupt requests are enabled (CHxIE=1), clear
CHxF by reading the TIM channel x status and control register with
CHxF set and then writing a logic zero to CHxF. If another interrupt
request occurs before the clearing sequence is complete, then writing
logic zero to CHxF has no effect. Therefore, an interrupt request
cannot be lost due to inadvertent clearing of CHxF.
Reset clears the CHxF bit. Writing a logic one to CHxF has no effect.
1 = Input capture or output compare on channel x
0 = No input capture or output compare on channel x
CHxIE — Channel x Interrupt Enable Bit
This read/write bit enables TIM CPU interrupt service requests on
channel x. Reset clears the CHxIE bit.
1 = Channel x CPU interrupt requests enabled
0 = Channel x CPU interrupt requests disabled
MSxB — Mode Select Bit B
This read/write bit selects buffered output compare/PWM operation.
MSxB exists only in the TIM channel 0 status and control register.
Setting MS0B disables the channel 1 status and control register and
reverts TCH1 to general-purpose I/O.
Reset clears the MSxB bit.
1 = Buffered output compare/PWM operation enabled
0 = Buffered output compare/PWM operation disabled
MSxA — Mode Select Bit A
When ELSxB:A ≠ 0:0, this read/write bit selects either input capture
operation or unbuffered output compare/PWM operation.
See Table 11-3.
1 = Unbuffered output compare/PWM operation
0 = Input capture operation
When ELSxB:A = 0:0, this read/write bit selects the initial output level
of the TCHx pin. (See Table 11-3.) Reset clears the MSxA bit.
1 = Initial output level low
0 = Initial output level high
Data Sheet
166
MC68HC908LD64 — Rev. 3.0
Timer Interface Module (TIM)
Freescale Semiconductor
Timer Interface Module (TIM)
I/O Registers
NOTE:
Before changing a channel function by writing to the MSxB or MSxA bit,
set the TSTOP and TRST bits in the TIM status and control register
(TSC).
ELSxB and ELSxA — Edge/Level Select Bits
When channel x is an input capture channel, these read/write bits
control the active edge-sensing logic on channel x.
When channel x is an output compare channel, ELSxB and ELSxA
control the channel x output behavior when an output compare
occurs.
When ELS0B and ELS0A are both clear, channel 0 is not connected
to the CLAMP/TCH0 pin. The pin is available as the CLAMP output of
the sync processor.
Table 11-3 shows how ELSxB and ELSxA work. Reset clears the
ELSxB and ELSxA bits.
Table 11-3. Mode, Edge, and Level Selection
MSxB
MSxA
ELSxB
ELSxA
X
0
0
0
Mode
Output
Preset
X
1
0
0
0
0
0
1
0
0
1
0
0
0
1
1
0
1
0
1
0
1
1
0
0
1
1
1
1
X
0
1
1
X
1
0
1
X
1
1
Configuration
Pin is CLAMP of sync processor(1);
Initial Output Level High
Pin is CLAMP of sync processor(1);
Initial Output Level Low
Capture on Rising Edge Only
Input
Capture
Capture on Falling Edge Only
Capture on Rising or Falling Edge
Output
Compare
or PWM
Toggle Output on Compare
Clear Output on Compare
Set Output on Compare
Buffered
Toggle Output on Compare
Output
Clear Output on Compare
Compare or
Buffered
Set Output on Compare
PWM
Notes:
1. For CLAMP/TCH0 pin only.
NOTE:
Before enabling a TIM channel register for input capture operation, make
sure that the TCHx pin is stable for at least two bus clocks.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Timer Interface Module (TIM)
167
Timer Interface Module (TIM)
TOVx — Toggle-On-Overflow Bit
When channel x is an output compare channel, this read/write bit
controls the behavior of the channel x output when the TIM counter
overflows. When channel x is an input capture channel, TOVx has no
effect. Reset clears the TOVx bit.
1 = Channel x pin toggles on TIM counter overflow.
0 = Channel x pin does not toggle on TIM counter overflow.
NOTE:
When TOVx is set, a TIM counter overflow takes precedence over a
channel x output compare if both occur at the same time.
CHxMAX — Channel x Maximum Duty Cycle Bit
When the TOVx bit is at logic one, setting the CHxMAX bit forces the
duty cycle of buffered and unbuffered PWM signals to 100%. As
Figure 11-7 shows, the CHxMAX bit takes effect in the cycle after it
is set or cleared. The output stays at the 100% duty cycle level until
the cycle after CHxMAX is cleared.
OVERFLOW
OVERFLOW
OVERFLOW
OVERFLOW
OVERFLOW
PERIOD
TCHx
OUTPUT
COMPARE
OUTPUT
COMPARE
OUTPUT
COMPARE
OUTPUT
COMPARE
CHxMAX
Figure 11-7. CHxMAX Latency
11.10.5 TIM Channel Registers (TCH0H/L:TCH1H/L)
These read/write registers contain the captured TIM counter value of the
input capture function or the output compare value of the output
compare function. The state of the TIM channel registers after reset is
unknown.
In input capture mode (MSxB:MSxA = 0:0), reading the high byte of the
TIM channel x registers (TCHxH) inhibits input captures until the low
byte (TCHxL) is read.
Data Sheet
168
MC68HC908LD64 — Rev. 3.0
Timer Interface Module (TIM)
Freescale Semiconductor
Timer Interface Module (TIM)
I/O Registers
In output compare mode (MSxB:MSxA ≠ 0:0), writing to the high byte of
the TIM channel x registers (TCHxH) inhibits output compares until the
low byte (TCHxL) is written.
Address:
$0011
TCH0H
Bit 7
6
5
4
3
2
1
Bit 0
Bit15
Bit14
Bit13
Bit12
Bit11
Bit10
Bit9
Bit8
Read:
Write:
Reset:
Address:
Indeterminate after reset
$0012
TCH0L
Bit 7
6
5
4
3
2
1
Bit 0
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
Read:
Write:
Reset:
Address:
Indeterminate after reset
$0014
TCH1H
Bit 7
6
5
4
3
2
1
Bit 0
Bit15
Bit14
Bit13
Bit12
Bit11
Bit10
Bit9
Bit8
Read:
Write:
Reset:
Address:
Indeterminate after reset
$0015
TCH1L
Bit 7
6
5
4
3
2
1
Bit 0
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
Read:
Write:
Reset:
Indeterminate after reset
Figure 11-8. TIM Channel Registers (TCH0H/L:TCH1H/L)
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Timer Interface Module (TIM)
169
Timer Interface Module (TIM)
Data Sheet
170
MC68HC908LD64 — Rev. 3.0
Timer Interface Module (TIM)
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 12. Pulse Width Modulator (PWM)
12.1 Contents
12.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
12.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171
12.4 PWM Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
12.4.1 PWM Data Registers 0 to 7 (0PWM–7PWM). . . . . . . . . . . 173
12.4.2 PWM Control Register (PWMCR) . . . . . . . . . . . . . . . . . . . 174
12.2 Introduction
Eight 8-bit PWM channels are available on the MC68HC908LD64.
Channels 0 to 7 are shared with port-B I/O pins under the control of the
PWM control register.
12.3 Functional Description
Each 8-Bit PWM channel is composed of an 8-bit register which contains
a 5-bit PWM in MSB portion and a 3-bit binary rate multiplier (BRM) in
LSB portion. There are eight PWM data registers, controlling each PWM
channel. The value programmed in the 5-bit PWM portion will determine
the pulse length of the output. The clock to the 5-bit PWM portion is the
system bus clock, the repetition rate of the output is hence 187.5kHz at
6MHz clock.
The 3-bit BRM will generate a number of narrow pulses which are
equally distributed among an 8-PWM-cycle frame. The number of pulses
generated is equal to the number programmed in the 3-bit BRM portion.
Example of the waveforms are shown in Figure 12-4.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Pulse Width Modulator (PWM)
171
Pulse Width Modulator (PWM)
Combining the 5-bit PWM together with the 3-bit BRM, the average duty
cycle at the output will be (M+N/8)/32, where M is the content of the 5-bit
PWM portion, and N is the content of the 3-bit BRM portion. Using this
mechanism, a true 8-bit resolution PWM type DAC with reasonably high
repetition rate can be obtained.
The value of each PWM data register is continuously compared with the
content of an internal counter to determine the state of each PWM
channel output pin. Double buffering is not used in this PWM design.
Addr.
$0070
$0071
$0072
$0073
$0074
$0075
$0076
$0077
$0078
Register Name
PWM0 Data Register
(0PWM)
Read:
PWM1 Data Register
(1PWM)
Read:
PWM2 Data Register
(2PWM)
Read:
PWM3 Data Register
(3PWM)
Read:
PWM4 Data Register
(4PWM)
Read:
PWM5 Data Register
(5PWM)
Read:
PWM6 Data Register
(6PWM)
Read:
PWM7 Data Register
(7PWM)
Read:
PWM Control Register
(PWMCR)
Read:
Bit 7
6
5
4
3
2
1
Bit 0
0PWM4
0PWM3
0PWM2
0PWM1
0PWM0
0BRM2
0BRM1
0BRM0
1PWM4
1PWM3
1PWM2
1PWM1
1PWM0
1BRM2
1BRM1
1BRM0
2PWM4
2PWM3
2PWM2
2PWM1
2PWM0
2BRM2
2BRM1
2BRM0
3PWM4
3PWM3
3PWM2
3PWM1
3PWM0
3BRM2
3BRM1
3BRM0
4PWM4
4PWM3
4PWM2
4PWM1
4PWM0
4BRM2
4BRM1
4BRM0
5PWM4
5PWM3
5PWM2
5PWM1
5PWM0
5BRM2
5BRM1
5BRM0
6PWM4
6PWM3
6PWM2
6PWM1
6PWM0
6BRM2
6BRM1
6BRM0
7PWM4
7PWM3
7PWM2
7PWM1
7PWM0
7BRM2
7BRM1
7BRM0
PWM7E
PWM6E
PWM5E
PWM4E
PWM3E
PWM2E
PWM1E
PWM0E
0
0
0
0
0
0
0
0
Write:
Write:
Write:
Write:
Write:
Write:
Write:
Write:
Write:
Reset:
Figure 12-1. PWM I/O Register Summary
Data Sheet
172
MC68HC908LD64 — Rev. 3.0
Pulse Width Modulator (PWM)
Freescale Semiconductor
Pulse Width Modulator (PWM)
PWM Registers
12.4 PWM Registers
The PWM module uses of nine registers for data and control functions.
•
PWM data registers ($0070–$0077)
•
PWM control register ($0078)
12.4.1 PWM Data Registers 0 to 7 (0PWM–7PWM)
Address:
$0070–$0077
Bit 7
6
5
4
3
2
1
Bit 0
xPWM4
xPWM3
xPWM2
xPWM1
xPWM0
xBRM2
xBRM1
xBRM0
0
0
0
0
0
0
0
0
Read:
Write:
Reset:
Figure 12-2. PWM Data Registers 0 to 7 (0PWM–7PWM)
The output waveform of the eight PWM channels are each configured by
an 8-bit register, which contains a 5-bit PWM in MSB portion and a 3-bit
binary rate multiplier (BRM) in LSB portion
xPWM4–xPWM0 — PWM Bits
The value programmed in the 5-bit PWM portion will determine the
pulse length of the output. The clock to the 5-bit PWM portion is the
system bus clock, the repetition rate of the output is hence fOP ÷ 32.
Examples of PWM output waveforms are shown in Figure 12-4.
xBRM2–xBRM0 — Binary Rate Multiplier Bits
The 3-bit BRM will generate a number of narrow pulses which are
equally distributed among an 8-PWM-cycle frame. The number of
pulses generated is equal to the number programmed in the 3-bit
BRM portion. Examples of PWM output waveforms are shown in
Figure 12-4.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Pulse Width Modulator (PWM)
173
Pulse Width Modulator (PWM)
12.4.2 PWM Control Register (PWMCR)
Address:
$0078
Bit 7
6
5
4
3
2
1
Bit 0
PWM7E
PWM6E
PWM5E
PWM4E
PWM3E
PWM2E
PWM1E
PWM0E
0
0
0
0
0
0
0
0
Read:
Write:
Reset:
Figure 12-3. PWM Control Register (PWMCR)
PWM7E–PWM0E — PWM Output Enable
Setting a bit to 1 will enable the corresponding PWM channel to use
as PWM output. A zero configures the corresponding PWM pin as a
standard I/O port pin. Reset clears these bits.
1 = Port pin configured as PWM output
0 = Port pin configured as standard I/O port pin.
Table 12-1. PWM Channels and Port I/O pins
Port Pin
PWM Channel
Control Bit
PTB0
PWM0
PWM0E
PTB1
PWM1
PWM1E
PTB2
PWM2
PWM2E
PTB3
PWM3
PWM3E
PTB4
PWM4
PWM4E
PTB5
PWM5
PWM5E
PTB6
PWM6
PWM6E
PTB7
PWM7
PWM7E
Data Sheet
174
MC68HC908LD64 — Rev. 3.0
Pulse Width Modulator (PWM)
Freescale Semiconductor
Pulse Width Modulator (PWM)
PWM Registers
1 PWM cycle = 32T
M=$00
T
M=$01
31T
16T
M=$0F
16T
31T
M=$1F
Pulse inserted at end of PWM cycle
depends on setting of N.
T
T=1 CPU clock period (0.167ms if CPU clock=6MHz)
M = value set in 5-bit PWM (bit3-bit7)
N = value set in 3-bit BRM (bit0-bit2)
N
xx1
x1x
1xx
PWM cycles where pulses are
inserted in a 8-cycle frame
4
2, 6
1, 3, 5, 7
Number of inserted pulses in
a 8-cycle frame
1
2
4
Figure 12-4. 8-Bit PWM Output Waveforms
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Pulse Width Modulator (PWM)
175
Pulse Width Modulator (PWM)
Data Sheet
176
MC68HC908LD64 — Rev. 3.0
Pulse Width Modulator (PWM)
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 13. Analog-to-Digital Converter (ADC)
13.1 Contents
13.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
13.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
13.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .179
13.4.1 ADC Port I/O Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
13.4.2 Voltage Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180
13.4.3 Conversion Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
13.4.4 Continuous Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
13.4.5 Accuracy and Precision . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
13.5
Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181
13.6 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
13.6.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181
13.6.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .182
13.7 I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
13.7.1 ADC Analog Power Pin (VDDA). . . . . . . . . . . . . . . . . . . . . 182
13.7.2 ADC Analog Ground Pin (VSSA) . . . . . . . . . . . . . . . . . . . .182
13.7.3 ADC Voltage Reference High Pin (VRH) . . . . . . . . . . . . . . 182
13.7.4 ADC Voltage Reference Low Pin (VRL). . . . . . . . . . . . . . . 182
13.7.5 ADC Voltage In (ADCVIN) . . . . . . . . . . . . . . . . . . . . . . . . . 182
13.8 I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
13.8.1 ADC Status and Control Register. . . . . . . . . . . . . . . . . . . .183
13.8.2 ADC Data Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
13.8.3 ADC Input Clock Register . . . . . . . . . . . . . . . . . . . . . . . . . 185
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Analog-to-Digital Converter (ADC)
177
Analog-to-Digital Converter (ADC)
13.2 Introduction
This section describes the analog-to-digital converter (ADC). The ADC
is a 6-channel 8-bit successive approximation ADC.
13.3 Features
Features of the ADC module include:
Addr.
$003B
•
Six channels with multiplexed input
•
Linear successive approximation
•
8-bit resolution
•
Single or continuous conversion
•
Conversion complete flag or conversion complete interrupt
Register Name
Bit 7
Read:
ADC Status and Control
Register Write:
(ADSCR)
Reset:
Read:
6
5
4
3
2
1
Bit 0
AIEN
ADCO
ADCH4
ADCH3
ADCH2
ADCH1
ADCH0
0
0
0
1
1
1
1
1
AD7
AD6
AD5
AD4
AD3
AD2
AD1
AD0
COCO
ADC Data Register
Write:
(ADR)
Reset:
$003C
Indeterminate after reset
Read:
$003D
ADC Input Clock Register
Write:
(ADICLK)
Reset:
ADIV2
ADIV1
ADIV0
0
0
0
0
0
0
0
0
0
0
0
0
0
= Unimplemented
Figure 13-1. ADC I/O Register Summary
Data Sheet
178
MC68HC908LD64 — Rev. 3.0
Analog-to-Digital Converter (ADC)
Freescale Semiconductor
Analog-to-Digital Converter (ADC)
Functional Description
13.4 Functional Description
Six ADC channels are available for sampling external sources at pins
PTC5–PTC0. An analog multiplexer allows the single ADC converter to
select one of the six ADC channels as ADC voltage input (ADCVIN).
ADCVIN is converted by the successive approximation register-based
counters. The ADC resolution is eight bits. When the conversion is
completed, ADC puts the result in the ADC data register and sets a flag
or generates an interrupt. Figure 13-2 shows a block diagram of the
ADC.
INTERNAL
DATA BUS
READ DDRC
DISABLE
WRITE DDRC
DDRCx
RESET
WRITE PTC
PTCx/ADCx
PTCx
READ PTC
ADC DATA REGISTER
INTERRUPT
LOGIC
AIEN
CONVERSION
COMPLETE
COCO
BUS CLOCK
ADC
DISABLE
ADC VOLTAGE IN
ADCVIN
ADC CHANNEL x
CHANNEL
SELECT
(1 OF 6 CHANNELS)
ADCH[4:0]
ADC CLOCK
CLOCK
GENERATOR
ADIV[2:0]
Figure 13-2. ADC Block Diagram
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Analog-to-Digital Converter (ADC)
179
Analog-to-Digital Converter (ADC)
13.4.1 ADC Port I/O Pins
PTC5/ADC5–PTC0/ADC0 are general-purpose I/O pins that are shared
with the ADC channels. The channel select bits, ADCH[4:0], in the ADC
status and control register define which ADC channel/port pin will be
used as the input signal. The ADC overrides the port I/O logic by forcing
that pin as input to the ADC. The remaining ADC channels/port pins are
controlled by the port I/O logic and can be used as general-purpose I/O.
Writes to the port register or DDR will not have any affect on the port pin
that is selected by the ADC. Read of a port pin which is in use by the
ADC will return a logic 0 if the corresponding DDR bit is at logic 0. If the
DDR bit is at logic 1, the value in the port data latch is read.
13.4.2 Voltage Conversion
When the input voltage to the ADC equals to VRH, the ADC converts the
signal to $FF (full scale). If the input voltage equals to VRL, the ADC
converts it to $00. Input voltages between VRH and VRL is a straight-line
linear conversion. All other input voltages will result in $FF if greater than
VRH and $00 if less than VRL.
NOTE:
Input voltage should not exceed the analog supply voltages.
13.4.3 Conversion Time
Sixteen ADC internal clocks are required to perform one conversion. The
ADC starts a conversion on the first rising edge of the ADC internal clock
immediately following a write to the ADSCR. If the ADC internal clock is
selected to run at 1MHz, then one conversion will take 16µs to complete.
With a 1MHz ADC internal clock the maximum sample rate is 62.5kHz.
Conversion time =
16 to17 ADC cycles
ADC frequency
Number of bus cycles = conversion time × bus frequency
Data Sheet
180
MC68HC908LD64 — Rev. 3.0
Analog-to-Digital Converter (ADC)
Freescale Semiconductor
Analog-to-Digital Converter (ADC)
Interrupts
13.4.4 Continuous Conversion
In the continuous conversion mode, the ADC continuously converts the
selected channel filling the ADC data register with new data after each
conversion. Data from the previous conversion will be overwritten
whether that data has been read or not. Conversions will continue until
the ADCO bit is cleared. The conversion complete bit, COCO, in the
ADC status and control register is set after each conversion and can be
cleared by writing to the ADC status and control register or reading of the
ADC data register.
13.4.5 Accuracy and Precision
The conversion process is monotonic and has no missing codes.
13.5 Interrupts
When the AIEN bit is set, the ADC module is capable of generating a
CPU interrupt after each ADC conversion. A CPU interrupt is generated
if the COCO bit is at logic 0. The COCO bit is not used as a conversion
complete flag when interrupts are enabled. The interrupt vector is
defined in Table 2-1 . Vector Addresses.
13.6 Low-Power Modes
The WAIT and STOP instruction can put the MCU in low-power
consumption standby modes.
13.6.1 Wait Mode
The ADC continues normal operation during wait mode. Any enabled
CPU interrupt request from the ADC can bring the MCU out of wait
mode. If the ADC is not required to bring the MCU out of wait mode,
power down the ADC by setting the ADCH[4:0] bits in the ADC status
and control register to logic 1’s before executing the WAIT instruction.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Analog-to-Digital Converter (ADC)
181
Analog-to-Digital Converter (ADC)
13.6.2 Stop Mode
The ADC module is inactive after the execution of a STOP instruction.
Any pending conversion is aborted. ADC conversions resume when the
MCU exits stop mode. Allow one conversion cycle to stabilize the analog
circuitry before attempting a new ADC conversion after exiting stop
mode.
13.7 I/O Signals
The ADC module has six channels that are shared with port C I/O pins,
PTC5/ADC5–PTC0/ADC0.
13.7.1 ADC Analog Power Pin (VDDA)
The ADC analog portion uses VDDA as its power pin. Connect the
VDDA pin to the same voltage potential as VDD. External filtering may
be necessary to ensure clean VDDA for good results.
NOTE:
Route VDDA carefully for maximum noise immunity and place bypass
capacitors as close as possible to the package.
13.7.2 ADC Analog Ground Pin (VSSA)
The ADC analog portion uses VSSA as its ground pin. Connect the
VSSA pin to the same voltage potential as VSS.
13.7.3 ADC Voltage Reference High Pin (VRH)
VRH is the high voltage reference for the ADC.
13.7.4 ADC Voltage Reference Low Pin (VRL)
VRL is the low voltage reference for the ADC.
13.7.5 ADC Voltage In (ADCVIN)
ADCVIN is the input voltage signal from one of the six ADC channels to
the ADC module.
Data Sheet
182
MC68HC908LD64 — Rev. 3.0
Analog-to-Digital Converter (ADC)
Freescale Semiconductor
Analog-to-Digital Converter (ADC)
I/O Registers
13.8 I/O Registers
Three I/O registers control and monitor ADC operation:
•
ADC status and control register (ADSCR)
•
ADC data register (ADR)
•
ADC input clock register (ADICLK)
13.8.1 ADC Status and Control Register
Function of the ADC status and control register is described here.
Address:
$003B
Bit 7
Read:
6
5
4
3
2
1
Bit 0
AIEN
ADCO
ADCH4
ADCH3
ADCH2
ADCH1
ADCH0
0
0
1
1
1
1
1
COCO
Write:
Reset:
0
= Unimplemented
Figure 13-3. ADC Status and Control Register (ADSCR)
COCO — Conversions Complete Bit
When the AIEN bit is a logic 0, the COCO is a read-only bit which is
set each time a conversion is completed. This bit is cleared whenever
the ADC status and control register is written, or whenever the ADC
data register is read. Reset clears this bit.
When the AIEN bit is a logic 1 (CPU interrupt enabled), the COCO is
a read-only bit, and will always be logic 0 when read.
1 = conversion completed (AIEN = 0)
0 = conversion not completed (AIEN = 0)
AIEN — ADC Interrupt Enable Bit
When this bit is set, an interrupt is generated at the end of an ADC
conversion. The interrupt signal is cleared when the data register is
read or the status and control register is written. Reset clears the
AIEN bit.
1 = ADC interrupt enabled
0 = ADC interrupt disabled
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Analog-to-Digital Converter (ADC)
183
Analog-to-Digital Converter (ADC)
ADCO — ADC Continuous Conversion Bit
When set, the ADC will convert samples continuously and update the
ADR register at the end of each conversion. Only one conversion is
allowed when this bit is cleared. Reset clears the ADCO bit.
1 = Continuous ADC conversion
0 = One ADC conversion
ADCH[4:0] — ADC Channel Select Bits
ADCH[4:0] form a 5-bit field which is used to select one of the ADC
channels or reference voltages. The five channel select bits are
detailed in the Table 13-1.
NOTE:
Care should be taken when using a port pin as both an analog and a
digital input simultaneously to prevent switching noise from corrupting
the analog signal.
NOTE:
Recovery from the disabled state requires one conversion cycle to
stabilize.
Table 13-1. MUX Channel Select
ADCH4
ADCH3
ADCH2
ADCH1
ADCH0
ADC Channel
Input Select
0
0
0
0
0
ADC0
PTC0/ADC0
0
0
0
0
1
ADC1
PTC1/ADC1
0
0
0
1
0
ADC2
PTC2/ADC2
0
0
0
1
1
ADC3
PTC3/ADC3
0
0
1
0
0
ADC4
PTC4/ADC4
0
0
1
0
1
ADC5
PTC5/ADC5
0
0
1
1
0
↓
↓
↓
↓
↓
—
Unused(1)
1
1
0
1
0
1
1
0
1
1
—
Reserved
1
1
1
0
0
—
Unused
1
1
1
0
1
VRH
1
1
1
1
0
VRL
1
1
1
1
1
ADC power off
Notes:
1. If any unused channels are selected, the resulting ADC conversion will be unknown.
Data Sheet
184
MC68HC908LD64 — Rev. 3.0
Analog-to-Digital Converter (ADC)
Freescale Semiconductor
Analog-to-Digital Converter (ADC)
I/O Registers
13.8.2 ADC Data Register
One 8-bit result register, ADC data register (ADR), is provided. This
register is updated each time an ADC conversion completes.
Address:
Read:
$003C
Bit 7
6
5
4
3
2
1
Bit 0
AD7
AD6
AD5
AD4
AD3
AD2
AD1
AD0
Write:
Reset:
Indeterminate after reset
= Unimplemented
Figure 13-4. ADC Data Register (ADR)
13.8.3 ADC Input Clock Register
The ADC input clock register (ADICLK) selects the clock frequency for
the ADC.
Address:
$003D
Bit 7
6
5
ADIV2
ADIV1
ADIV0
0
0
0
Read:
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
0
0
Write:
Reset:
= Unimplemented
Figure 13-5. ADC Input Clock Register (ADICLK)
ADIV[2:0] — ADC Clock Prescaler Bits
ADIV[2:0] form a 3-bit field which selects the divide ratio used by the
ADC to generate the internal ADC clock. Table 13-2 shows the
available clock configurations. The ADC clock should be set to
approximately 1MHz.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Analog-to-Digital Converter (ADC)
185
Analog-to-Digital Converter (ADC)
Table 13-2. ADC Clock Divide Ratio
ADIV2
ADIV1
ADIV0
ADC Clock Rate
0
0
0
ADC Input Clock ÷ 1
0
0
1
ADC Input Clock ÷ 2
0
1
0
ADC Input Clock ÷ 4
0
1
1
ADC Input Clock ÷ 8
1
X
X
ADC Input Clock ÷ 16
X = don’t care
Data Sheet
186
MC68HC908LD64 — Rev. 3.0
Analog-to-Digital Converter (ADC)
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 14. Universal Serial Bus Module (USB)
14.1 Contents
14.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
14.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
14.4
I/O Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
14.5
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192
14.6 Hub Function I/O Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 194
14.6.1 USB Hub Root Port Control Register (HRPCR) . . . . . . . . . 194
14.6.2 USB Hub Downstream Port Control Registers
(HDP1CR–HDP4CR) . . . . . . . . . . . . . . . . . . . . . . . . . . 195
14.6.3 USB SIE Timing Interrupt Register (SIETIR) . . . . . . . . . . . 198
14.6.4 USB SIE Timing Status Register (SIETSR) . . . . . . . . . . . . 200
14.6.5 USB Hub Address Register (HADDR) . . . . . . . . . . . . . . . . 202
14.6.6 USB Hub Interrupt Register 0 (HIR0) . . . . . . . . . . . . . . . . . 203
14.6.7 USB Hub Control Register 0 (HCR0) . . . . . . . . . . . . . . . . . 205
14.6.8 USB Hub Endpoint 1 Control and Data Register (HCDR) . 206
14.6.9 USB Hub Status Register (HSR) . . . . . . . . . . . . . . . . . . . . 208
14.6.10 USB Hub Endpoint 0 Data Registers (HE0D0–HE0D7). . . 209
14.7 Embedded Device Function I/O Registers . . . . . . . . . . . . . . . 209
14.7.1 USB Embedded Device Address Register (DADDR). . . . . 210
14.7.2 USB Embedded Device Interrupt Register 0 (DIR0) . . . . . 210
14.7.3 USB Embedded Device Interrupt Register 1 (DIR1) . . . . . 212
14.7.4 USB Embedded Device Control Register 0 (DCR0) . . . . . 213
14.7.5 USB Embedded Device Control Register 1 (DCR1) . . . . . 215
14.7.6 USB Embedded Device Control Register 2 (DCR2) . . . . . 216
14.7.7 USB Embedded Device Status Register (DSR) . . . . . . . . . 217
14.7.8 USB Embedded Device Endpoint 0 Data Registers
(DE0D0–DE0D7). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
14.7.9 USB Embedded Device Endpoint 1/2 Data Registers
(DE1D0–DE1D7). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Universal Serial Bus Module (USB)
187
Universal Serial Bus Module (USB)
14.2 Introduction
This section describes the Universal Serial Bus (USB) module. This
MC68HC908LD64’s USB module supports both embedded full-speed
device and hub functions with one upstream port and four downstream
ports.
14.3 Features
Features of the USB module include the following:
•
Integrated USB transceiver supporting both full-speed and
low-speed functions
•
USB data control logic
– Packet decoding/generation
– CRC generation and checking
– NRZI encoding/decoding
– Bit-stuffing
•
USB reset support
•
Suspend and resume operations
•
Remote wakeup support
•
STALL, NAK, and ACK handshake generation
Features of the hub function include the following:
•
Hub control endpoint 0
– 8-byte transmit buffer
– 8-byte receive buffer
•
Hub interrupt endpoint 1
– 1-byte transmit buffer
•
USB interrupts
– Transaction interrupt driven
– Start of frame interrupt
Data Sheet
188
MC68HC908LD64 — Rev. 3.0
Universal Serial Bus Module (USB)
Freescale Semiconductor
Universal Serial Bus Module (USB)
I/O Pins
– EOF2 interrupt
– End of packet interrupt
– Signal transition interrupt
– Frame timer locked interrupt
•
Hub repeater and controller function
– Downstream and upstream connectivity
– Bus state evaluation
– Selective reset, suspend and resume
– Fault condition hardware detection
Features of the embedded device function include the following:
•
Device control endpoint 0
– 8-byte transmit buffer
– 8-byte receive buffer
•
Device interrupt endpoints 1 and 2
– 8-byte transmit buffer
•
USB generated interrupts
– transaction interrupt driven
14.4 I/O Pins
The USB module uses ten I/O pin (five pairs), with two dedicated pins for
the upstream port pair and eight shared port I/O pins for the downstream
ports. The full name of the USB I/O pins are listed in Table 14-1. The
generic pin name appear in the text that follows.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Universal Serial Bus Module (USB)
189
Universal Serial Bus Module (USB)
Table 14-1. USB I/O Pins
USB
Generic Pin Names:
Full MCU Pin Names:
D0+
DPLUS0
D0–
DMINUS0
D1+
PTE0/DPLUS1
D1–
PTE1/DMINUS1
D2+
PTE2/DPLUS2
D2–
PTE3/DMINUS2
D3+
PTE4/DPLUS3
D3–
PTE5/DMINUS3
D4+
PTE6/DPLUS4
D4–
PTE7/DMINUS4
Pin Selected for
USB Function By:
—
USBDS1E bit in PECR ($0068)
USBDS2E bit in PECR ($0068)
USBDS3E bit in PECR ($0068)
USBDS4E bit in PECR ($0068)
Addr.
Register Name
Bit 7
$0020
to
$0027
USB Embedded Device Read: DE0Rx7
Endpoint 0 Data
Write: DE0Tx7
Register 0 to 7
(DE0D0 to DE0D7) Reset:
$0028
to
$002F
USB Embedded Device Read:
Endpoint 1/2 Data
Write: DE1Tx7
Register 0 to 7
(DE1D0 to DE1D7) Reset:
$0030
to
$0037
Read: HE0Rx7
USB Hub Endpoint 0
Data Register 0 to 7 Write: HE0Tx7
(HE0D0 to HE0D7) Reset:
$0047
$0048
Read:
USB Embedded Device
Control Register 2 Write:
(DCR2)
Reset:
6
5
4
3
2
1
Bit 0
DE0Rx6
DE0Rx5
DE0Rx4
DE0Rx3
DE0Rx2
DE0Rx1
DE0Rx0
DE0Tx6
DE0Tx5
DE0Tx4
DE0Tx3
DE0Tx2
DE0Tx1
DE0Tx0
DE1Tx2
DE1Tx1
DE1Tx0
Indeterminate after reset
DE1Tx6
DE1Tx5
DE1Tx4
DE1Tx3
Indeterminate after reset
HE0Rx6
HE0Rx5
HE0Rx4
HE0Rx3
HE0Rx2
HE0Rx1
HE0Rx0
HE0Tx6
HE0Tx5
HE0Tx4
HE0Tx3
HE0Tx2
HE0Tx1
HE0Tx0
Indeterminate after reset
0
0
0
0
0
0
0
0
0
0
0
0
DADD6
DADD5
DADD4
DADD3
DADD2
DADD1
DADD0
0
0
0
0
0
0
0
Read:
USB Embedded Device
DEVEN
Address Register Write:
(DADDR) Reset:
0
X = Indeterminate
ENABLE2 ENABLE1 DSTALL2 DSTALL1
= Unimplemented
Figure 14-1. USB I/O Register Summary
Data Sheet
190
MC68HC908LD64 — Rev. 3.0
Universal Serial Bus Module (USB)
Freescale Semiconductor
Universal Serial Bus Module (USB)
I/O Pins
$0049
$004A
$004B
$004C
$004D
Read: TXD0F
USB Embedded Device
Interrupt Register 0 Write:
(DIR0)
Reset:
0
RXD0F
0
0
0
Read: TXD1F
USB Embedded Device
Interrupt Register 1 Write:
(DIR1)
Reset:
0
0
0
0
Read:
USB Embedded Device
T0SEQ
Control Register 0 Write:
(DCR0)
Reset:
0
Read:
USB Embedded Device
T1SEQ
Control Register 1 Write:
(DCR1) Reset:
0
USB Embedded Device Read: DRSEQ
Status Register Write:
(DSR) Reset:
0
0
0
0
0
TXD0FR
RXD0FR
0
0
0
0
0
0
TXD0IE
RXD0IE
0
TXD1IE
TXD1FR
0
0
0
0
0
0
0
DSTALL0
TX0E
RX0E
TP0SIZ3
TP0SIZ2
TP0SIZ1
TP0SIZ0
0
0
0
0
0
0
0
ENDADD
TX1E
TP1SIZ3
TP1SIZ2
TP1SIZ1
TP1SIZ0
0
0
0
0
0
0
0
DSETUP
DTX1ST
0
RP0SIZ3
RP0SIZ2
RP0SIZ1
RP0SIZ0
0
0
0
0
D1+
D1–
0
X
X
0
D2+
D2–
0
X
X
0
D3+
D3–
0
X
X
0
D4+
D4–
0
DTX1STR
0
0
0
0
PEN1
LOWSP1
RST1
RESUM1
SUSP1
0
0
0
0
0
PEN2
LOWSP2
RST2
RESUM2
SUSP2
0
0
0
0
0
PEN3
LOWSP3
RST3
RESUM3
SUSP3
0
0
0
0
0
PEN4
LOWSP4
RST4
RESUM4
SUSP4
0
0
0
0
0
0
X
X
USB SIE Timing Interrupt Read:
$0056
Register Write:
(SIETIR)
Reset:
SOFF
EOF2F
EOPF
TRANF
SOFIE
EOF2IE
EOPIE
TRANIE
0
0
0
0
0
0
0
0
USB SIE Timing Status Read:
Register Write:
(SIETSR)
Reset:
RSTF
0
LOCKF
0
0
0
0
0
LOCKFR
SOFFR
EOF2FR
EOPFR
TRANFR
0
0
0
0
0
$0051
$0052
$0053
$0054
$0057
USB Hub Downstream Read:
Port 1 Control Register Write:
(HDP1CR) Reset:
USB Hub Downstream Read:
Port 2 Control Register Write:
(HDP2CR) Reset:
USB Hub Downstream Read:
Port 3 Control Register Write:
(HDP3CR)
Reset:
USB Hub Downstream Read:
Port 4 Control Register Write:
(HDP4CR)
Reset:
RSTFR
0*
0
X = Indeterminate
0
= Unimplemented
Figure 14-1. USB I/O Register Summary
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Universal Serial Bus Module (USB)
191
Universal Serial Bus Module (USB)
$0058
Read:
USB Hub Address
USBEN
Register Write:
(HADDR)
Reset:
0*
ADD6
ADD5
ADD4
ADD3
ADD2
ADD1
ADD0
0
0
0
0
0
0
0
0
0
TXDIE
RXDIE
0
0
TXDFR
RXDFR
* RSTF and USBEN are reset by a power-on reset (POR) only.
$0059
$005B
Read:
USB Hub Interrupt
Register 0 Write:
(HIR0)
Reset:
Read:
USB Hub Control
Register 0 Write:
(HCR0)
Reset:
TXDF
0
0
0
0
0
0
0
0
TSEQ
STALL0
TXE
RXE
TPSIZ3
TPSIZ2
TPSIZ1
TPSIZ0
0
0
0
0
0
0
0
0
PNEW
PCHG5
PCHG4
PCHG3
PCHG2
PCHG1
PCHG0
0
0
0
0
0
0
0
SETUP
TX1ST
0
RPSIZ3
RPSIZ2
RPSIZ1
RPSIZ0
X
X
X
X
0
D0+
D0–
0
X
X
USB Hub Endpoint 1 Read: STALL1
$005C Control and Data Register Write:
(HCDR)
Reset:
0
Read:
USB Hub Status Register
$005D
Write:
(HSR)
Reset:
$005E
USB Hub Root Port Read:
Control Register Write:
(HRPCR)
Reset:
RXDF
RSEQ
TX1STR
X
X
X
0
0
0
0
0
0
X = Indeterminate
0
RESUM0 SUSPND
0
0
= Unimplemented
Figure 14-1. USB I/O Register Summary
14.5 Overview
This USB module is designed to serve as a compound device. An
embedded full-speed device function is combined with a hub in a single
USB module.
For the hub sub-module, five basic properties can be supported by the
hardware or the software: connectivity behavior, power management,
device connect/disconnect detection, bus fault detection and recovery,
and full/low-speed device traffic control. Endpoint 0 of the hub submodule functions as a receive/transmit control endpoint. Endpoint 1 of
the hub sub-module functions as interrupt transfer to report the device
change state.
Data Sheet
192
MC68HC908LD64 — Rev. 3.0
Universal Serial Bus Module (USB)
Freescale Semiconductor
Universal Serial Bus Module (USB)
Overview
For the embedded device sub-module, three types of USB data transfers
are supported: control, interrupt, and bulk (transmit only). Endpoint 0 of
the embedded device sub-module functions as a receive/transmit
control endpoint. Endpoints 1 and 2 of the embedded device sub-module
can function as interrupt or bulk, but only in the transmit direction.
The block diagram of the USB module is shown Figure 14-2. The USB
module manages communications between the host and the USB
function. The module is partitioned into eight functional blocks. These
blocks consist of a dual function transceiver, the hub repeater function,
the serial interface engine (SIE), the frame counter logic, the hub control
logic, the embedded device control logic, and the endpoint registers.
CPU BUS
EMBEDDED DEVICE
CONTROL LOGIC
HUB
CONTROL LOGIC
ENDPOINT 0
(CONTROL ENDPOINT)
8-BYTE TRANSMIT BUFFER
8-BYTE RECEIVE BUFFER
ENDPOINT 0
(CONTROL ENDPOINT)
8-BYTE TRANSMIT BUFFER
8-BYTE RECEIVE BUFFER
REGISTERS
ENDPOINT 1/2
(INTERRUPT/BULK ENDPOINT)
8-BYTE TRANSMIT BUFFER
OSCOUT
FROM OSC
ENDPOINT 1
(INTERRUPT ENDPOINT)
8-BYTE TRANSMIT BUFFER
12MHz
FRAME
COUNTER
SERIAL
INTERFACE ENGINE
HUB REPEATER
48MHz
TRANSCEIVER
D4+ D4–
D3+ D3–
D2+ D2–
DOWNSTREAM PORTS
TRANSCEIVER
D1+ D1–
CLOCK
DOUBLER
24MHz
OSCXCLK
FROM OSC
D0+ D0–
ROOT PORT
Figure 14-2. USB Module Block Diagram
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Universal Serial Bus Module (USB)
193
Universal Serial Bus Module (USB)
14.6 Hub Function I/O Registers
The USB hub function provides a set of control/status registers and
sixteen data registers that provide storage for the buffering of data
between the USB hub function and the CPU.
14.6.1 USB Hub Root Port Control Register (HRPCR)
Address:
Read:
$005E
Bit 7
6
5
0
0
0
4
3
2
1
Bit 0
0
D0+
D0–
0
X
X
RESUM0 SUSPND
Write:
Reset:
0
0
X = Indeterminate
0
0
0
= Unimplemented
Figure 14-3. USB Hub Root Port Control Register (HRPCR)
RESUM0 — Force Resume to the Root Port
This read/write bit forces a resume signal (K state) onto the USB root
port data lines to initiate a remote wakeup. Software should control
the timing of the forced resume to be between 10ms and 15ms.
Reset clears this bit.
1 = Force root port data lines to K state
0 = Default
SUSPND — USB Suspend Control Bit
To save power, this read/write bit should be set by the software if a
constant idle state for more than 3ms is detected on the USB bus.
Setting this bit puts the transceiver into a power savings mode.
This bit also determines the latch scheme for the data lines of the root
port and the downstream port. When this bit is 1, the current state
shown on the data lines will be reflected to the data register (D+/D–)
directly. When the bit is 0, the data registers are the latched state
sampled at the last EOF2 sample point. The hub repeater’s function
is affected by this bit too. The upstream and downstream traffic will be
blocked if this bit is set to 1. When the global resume or the
downstream remote wakeup signal is found by the suspended hub,
Data Sheet
194
MC68HC908LD64 — Rev. 3.0
Universal Serial Bus Module (USB)
Freescale Semiconductor
Universal Serial Bus Module (USB)
Hub Function I/O Registers
software is responsible to propagate the traffic between the root port
and the enabled downstream port by setting the RESUMx control bit.
Reset clears this bit.
EOF2 is generated by the MCU every millisecond, if SOF is not
detected when three or more EOF2 have occurred, software can set
the SUSPND bit and put the MCU into suspend mode.
D0+, D0– — Root Port Differential Data
These read-only bits are the differential data shown on the hub root
ports. When the SUSPND bit is 0, the data is the latched state at the
last EOF2 sample point. When the SUSPND bit is 1, the data reflects
the current state on the data line while accessing this register.
14.6.2 USB Hub Downstream Port Control Registers (HDP1CR–HDP4CR)
Address:
$0051–$0054
HRP1CR–HRP4CR
Bit 7
6
5
4
3
PEN1
LOWSP1
RST1
RESUM1
SUSP1
PEN2
LOWSP2
RST2
RESUM2
SUSP2
PEN3
LOWSP3
RST3
RESUM3
SUSP3
PEN4
LOWSP4
RST4
RESUM4
SUSP4
0
0
0
0
0
Read:
2
1
Bit 0
0
D1+
D1–
0
D2+
D2–
0
D3+
D3–
0
D4+
D4–
0
X
X
Write:
Read:
Write:
Read:
Write:
Read:
Write:
Reset:
X = Indeterminate
= Unimplemented
Figure 14-4. USB Hub Downstream Port Control Registers
(HDP1CR–HDP4CR)
PENx — Downstream Port Enable Control Bit
This read/write bit determines whether the enabled or disabled state
should be assigned to the downstream port. Setting this bit to 1
enables the port; clearing this bit to 0 disables the port. In the enabled
state a full-speed port propagates all downstream signaling;
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Universal Serial Bus Module (USB)
195
Universal Serial Bus Module (USB)
a low-speed port propagates downstream low-speed packet traffic
when preceded by the preamble PID. An enabled port propagates all
upstream signaling including full-speed and low-speed packets. This
bit can be set to 1 by the host request only. It can be cleared either by
hardware when a fault condition was detected or by software through
the host request. Reset clears this bit.
1 = Downstream port is enabled
0 = Downstream port is disabled
LOWSPx — Full-Speed / Low-Speed Port Control Bit
This read/write bit specifies the attached device in the downstream
port is low-speed device or full-speed device. Software is responsible
to detect the device attachment and whether a device is full or
low-speed. Reset clears this bit.
1 = Downstream port is low-speed
0 = Downstream port is full-speed
NOTE:
After a port is enabled, the hub will automatically generate a low-speed
keep awake signal to the port every millisecond.
RSTx — Force Reset to the Downstream Port
This read/write bit forces a reset signal (SE0 state) onto the USB
downstream port data lines. This bit can be set by the host request
SetPortFeature (PORT_RESET) only. Software should control the
timing of the forced reset signaling downstream for at least 10ms.
Reset clears this bit.
1 = Force downstream port data lines to SE0 state
0 = Default
RESUMx — Force Resume to the Downstream Port
This read/write bit forces a resume signal (K state) onto the USB
downstream port data lines. This bit is set to reflect the resume signal
when the software detects the remote resume signal on the data lines
of the selective suspend downstream port. Downstream selective
resume sequence to a port may also be initiated via the host request
ClearPortFeature (PORT_SUSPEND). Software should control the
timing of the forced resume signaling downstream for at least 20ms.
Data Sheet
196
MC68HC908LD64 — Rev. 3.0
Universal Serial Bus Module (USB)
Freescale Semiconductor
Universal Serial Bus Module (USB)
Hub Function I/O Registers
To indicate the end of the resume, a low-speed EOP signal will be
followed when this control bit changes from 1 to 0. Reset clears this
bit.
1 = Force downstream port data lines to K state
0 = Default
SUSPx — Downstream Port Selective Suspend Bit
This read/write bit forces the downstream port entering the selective
suspend mode. This bit can be set by the host request SetPortFeature
(PORT_SUSPEND) only. When this bit is set, the hub prevents
propagating any bus activity (except the port reset or port resume
request or the global reset signal) downstream, and the port can only
reflect upstream bus state changes via the endpoint 1 of the hub. The
blocking occurs at the next EOF2 point when this bit is set. Reset
clears this bit.
1 = Force downstream port enters the selective suspend mode
0 = Default
Dx+, Dx– — Downstream Port Differential Data
These read-only bits are the differential data shown on the hub
downstream ports. When the SUSPND bit is 0 in the HRPCR register,
the data is the latched state at the last EOF2 sample point. When the
SUSPND bit is 1, the data reflects the current state on the data line
while accessing this register.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Universal Serial Bus Module (USB)
197
Universal Serial Bus Module (USB)
14.6.3 USB SIE Timing Interrupt Register (SIETIR)
Address:
Read:
$0056
Bit 7
6
5
4
SOFF
EOF2F
EOPF
TRANF
3
2
1
Bit 0
SOFIE
EOF2IE
EOPIE
TRANIE
0
0
0
0
Write:
Reset:
0
0
0
0
= Unimplemented
Figure 14-5. USB SIE Timing Interrupt Register (SIETIR)
SOFF — Start Of Frame Detect Flag
This read-only bit is set when a valid SOF PID is detected on the D0+
and D0– lines at the root port. Software must clear this flag by writing
a logic 1 to SOFFR bit in the SIETSR register. Reset clears this bit.
Writing to SOFF has no effect.
1 = Start Of Frame PID has been detected
0 = Start Of Frame PID has not been detected
EOF2F — Second End Of Frame Point Flag
This read-only bit is set when the internal frame timer counts to the bit
time that the hub must see upstream traffic terminated near the end
of frame. This bit time is defined as 10 bit times from the next Start Of
Frame PID. Software must clear this flag by writing a logic 1 to
EOF2FR bit in the SIETSR register. Reset clears this bit. Writing to
EOF2F has no effect.
1 = Frame timer counts to the EOF2 point
0 = Frame timer does not count to the EOF2 point
EOPF — End of Packet Detect Flag
This read-only bit is set when a valid End Of Packet sequence is
detected on the D0+ and D0– lines. Software must clear this flag by
writing a logic 1 to the EOPFR bit in the SIETSR register. Reset clears
this bit. Writing to EOPF has no effect.
1 = End-of-Packet sequence has been detected
0 = End-of-Packet sequence has not been detected
Data Sheet
198
MC68HC908LD64 — Rev. 3.0
Universal Serial Bus Module (USB)
Freescale Semiconductor
Universal Serial Bus Module (USB)
Hub Function I/O Registers
TRANF — Bus Signal Transition Detect Flag
This read-only bit is set if there is any bus activity on the upstream or
the downstream data lines. Generally, this bit is used to wake up the
suspended hub when there is any bus activity occurred. Software
must clear this flag by writing a logic 1 to the TRANFR bit in the
SIETSR register. Reset clears this bit. Writing to TRANF has no
effect.
1 = Signal transition has been detected
0 = Signal transition has not been detected
SOFIE — Start Of Frame Interrupt Enable
This read/write bit enables the Start Of Frame to generate a USB
interrupt when the SOFF bit becomes set. Reset clears this bit.
1 = USB interrupt enabled for Start Of Frame
0 = USB interrupt disabled for Start Of Frame
EOF2IE — The Second End of Frame Point Interrupt Enable
This read/write bit enables the Second End Of Frame to generate a
USB interrupt when the EOF2F bit becomes set. Reset clears this bit.
1 = USB interrupt enabled for the Second End Of Frame Point
0 = USB interrupt disabled for the Second End Of Frame Point
EOPIE — End of Packet Detect Interrupt Enable
This read/write bit enables the End Of Frame to generate a USB
interrupt when the EOPF bit becomes set. Reset clears the bit.
1 = USB interrupt enabled for End-of-Packet sequence detection
0 = USB interrupt disabled for End-of-Packet sequence detection
TRANIE — Bus Signal Transition Detect Interrupt Enable
This read/write bit enables the bus signal transition to generate a USB
interrupt when the TRANF bit becomes set. Reset clears this bit.
1 = USB interrupt enabled for Bus Signal Transition
0 = USB interrupt disabled for Bus Signal Transition
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Universal Serial Bus Module (USB)
199
Universal Serial Bus Module (USB)
14.6.4 USB SIE Timing Status Register (SIETSR)
Address:
Read:
$0057
Bit 7
6
5
4
3
2
1
Bit 0
RSTF
0
LOCKF
0
0
0
0
0
LOCKFR
SOFFR
EOF2FR
EOPFR
TRANFR
0
0
0
0
0
Write:
Reset:
RSTFR
0*
0
0
= Unimplemented
* RSTF is reset by a power-on reset (POR) only.
Figure 14-6. USB SIE Timing Status Register (SIETSR)
RSTF — USB Reset Flag
This read-only bit is set when a valid USB reset signal state is
detected on the D0+ and D0– lines. This bit is cleared by writing a
logic 1 to the RSTFR bit or by a MCU power-on reset.
1 = USB reset signal detected on D0+ and D0–
0 = No USB reset detected
RSTFR — Clear Reset Flag Bit
Writing a logic 1 to this write-only bit will clear the RSTF bit if it is set.
Reset clears this bit.
1 = Write 1 to clear the RSTF bit
0 = No effect
LOCKF — USB Frame Timer Locked
This read-only bit is set when the internal frame timer is locked to the
host timer. This bit is cleared by writing a logic 1 to the LOCKFR bit.
Reset clears this bit.
1 = Internal frame timer is locked to the host timer
0 = Internal frame timer is not locked to the host timer
LOCKFR — Clear Frame Timer Locked Flag
Writing a logic 1 to this write-only bit will clear the LOCKF bit if it is set.
Reset clears this bit.
1 = Write 1 to clear the LOCKF bit
0 = No effect
Data Sheet
200
MC68HC908LD64 — Rev. 3.0
Universal Serial Bus Module (USB)
Freescale Semiconductor
Universal Serial Bus Module (USB)
Hub Function I/O Registers
SOFFR — Start Of Frame Flag Reset
Writing a logic 1 to this write-only bit will clear the SOFF bit if it is set.
Reset clears this bit.
1 = Write 1 to clear the SOFF bit
0 = No effect
EOF2FR — The Second End of Frame Point Flag Reset
Writing a logic 1 to this write-only bit will clear the EOF2F bit if it is set.
Reset clears this bit.
1 = Write 1 to clear the EOF2F bit
0 = No effect
EOPFR — End of Packet Flag Reset
Writing a logic 1 to this write-only bit will clear the EOPF bit if it is set.
Reset clears this bit.
1 = Write 1 to clear the EOPF bit
0 = No effect
TRANFR — Bus Signal Transition Flag Reset
Writing a logic 1 to this write-only bit will clear the TRANF bit if it is set.
Reset clears this bit.
1 = Write 1 to clear TRANF bit
0 = No effect
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Universal Serial Bus Module (USB)
201
Universal Serial Bus Module (USB)
14.6.5 USB Hub Address Register (HADDR)
Address:
$0058
Bit 7
6
5
4
3
2
1
Bit 0
USBEN
ADD6
ADD5
ADD4
ADD3
ADD2
ADD1
ADD0
0*
0
0
0
0
0
0
0
Read:
Write:
Reset:
* USBEN is reset by a power-on reset (POR) only.
Figure 14-7. USB Hub Address Register (HADDR)
USBEN — USB Module Enable
This read/write bit enables and disables the USB module. When
USBEN is cleared, the USB module will not respond to any tokens.
Power-on reset clears this bit.
1 = USB module enabled
0 = USB module disabled; USB transceiver is also disabled to save
power.
ADD[6:0] — USB Hub Function Address
These bits specify the address of the hub function. Reset clears these
bits.
Data Sheet
202
MC68HC908LD64 — Rev. 3.0
Universal Serial Bus Module (USB)
Freescale Semiconductor
Universal Serial Bus Module (USB)
Hub Function I/O Registers
14.6.6 USB Hub Interrupt Register 0 (HIR0)
Address:
Read:
$0059
Bit 7
6
5
4
TXDF
RXDF
0
0
3
2
TXDIE
RXDIE
Write:
Reset:
0
0
0
0
0
0
1
Bit 0
0
0
TXDFR
RXDFR
0
0
= Unimplemented
Figure 14-8. USB Hub Interrupt Register 0 (HIR0)
TXDF — Hub Endpoint 0 Data Transmit Flag
This read-only bit is set after the data stored in hub endpoint 0
transmit buffers have been sent and an ACK handshake packet
received from the host. Once the next set of data is ready in the
transmit buffers, software must clear this flag by writing a logic 1 to the
TXDFR bit. To enable the next data packet transmission, TXE must
also be set. If TXDF bit is not cleared, a NAK handshake will be
returned in the next IN transaction. TXDF generates an interrupt
request to CPU if the TXDIE bit is also set. Writing to TXDF has no
effect. Reset clears this bit.
1 = Transmit on hub endpoint 0 has occurred
0 = Transmit on hub endpoint 0 has not occurred
RXDF — Hub Endpoint 0 Data Receive Flag
This read-only bit is set after the USB hub function has received a
data packet and responded with an ACK handshake packet. Software
must clear this flag by writing a logic 1 to the RXDFR bit after all data
received have been read. To enable the next data packet reception,
RXE must also be set. If RXDF bit is not cleared, a NAK handshake
will be returned in the next OUT transaction. RXDF generates an
interrupt request to CPU if the RXDIE bit is also set. Writing to RXDF
has no effect. Reset clears this bit.
1 = Receive on hub endpoint 0 has occurred
0 = Receive on hub endpoint 0 has not occurred
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Universal Serial Bus Module (USB)
203
Universal Serial Bus Module (USB)
TXDIE — Hub Endpoint 0 Transmit Interrupt Enable
This read/write bit enables the TXDF bit to generate CPU interrupt
request when set. Reset clears the TXDIE bit.
1 = TXDF CPU interrupt requests enabled
0 = TXDF CPU interrupt requests disabled
RXDIE — Hub Endpoint 0 Receive Interrupt Enable
This read/write bit enables the RXDF bit to generate CPU interrupt
request when set. Reset clears the RXDIE bit.
1 = RXDF CPU interrupt requests enabled
0 = RXDF CPU interrupt requests disabled
TXDFR — Hub Endpoint 0 Transmit Flag Reset
Writing a logic 1 to this write-only bit will clear the TXDF bit if it is set.
Reset clears this bit.
1 = Write 1 to clear the TXDF bit
0 = No effect
RXDFR — Hub Endpoint 0 Receive Flag Reset
Writing a logic 1 to this write-only bit will clear the RXDF bit if it is set.
Reset clears this bit.
1 = Write 1 to clear the RXDF bit
0 = No effect
Data Sheet
204
MC68HC908LD64 — Rev. 3.0
Universal Serial Bus Module (USB)
Freescale Semiconductor
Universal Serial Bus Module (USB)
Hub Function I/O Registers
14.6.7 USB Hub Control Register 0 (HCR0)
Address:
$005B
Bit 7
6
5
4
3
2
1
Bit 0
TSEQ
STALL0
TXE
RXE
TPSIZ3
TPSIZ2
TPSIZ1
TPSIZ0
0
0
0
0
0
0
0
0
Read:
Write:
Reset:
Figure 14-9. USB Hub Control Register 0 (HCR0)
TSEQ — Hub Endpoint 0 Transmit Sequence Bit
This read/write bit determines which type of data packet (DATA0 or
DATA1) will be sent during the next IN transaction directed at
endpoint 0. Toggling of this bit must be controlled by software. Reset
clears this bit.
1 = DATA1 token active for next hub endpoint 0 transmit
0 = DATA0 token active for next hub endpoint 0 transmit
STALL0 — Hub Endpoint 0 Force Stall Bit
This read/write bit causes hub endpoint 0 to return a STALL
handshake when polled by either an IN or OUT token by the host. The
USB hardware clears this bit when a SETUP token is received. Reset
clears this bit.
1 = Send STALL handshake
0 = Default
TXE — Hub Endpoint 0 Transmit Enable
This read/write bit enables a transmit to occur when the USB host
controller sends an IN token to the hub endpoint 0. Software should
set this bit when data is ready to be transmitted. It must be cleared by
software when no more hub endpoint 0 data packets needs to be
transmitted. If this bit is 0 or the TXDF is set, the USB will respond with
a NAK handshake to any hub endpoint 0 IN tokens. Reset clears this
bit.
1 = Data is ready to be sent
0 = Data is not ready; respond with NAK
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Universal Serial Bus Module (USB)
205
Universal Serial Bus Module (USB)
RXE — Hub Endpoint 0 Receive Enable
This read/write bit enables a receive to occur when the USB host
controller sends an OUT token to the hub endpoint 0. Software should
set this bit when data is ready to be received. It must be cleared by
software when data cannot be received. If this bit is 0 or the RXDF is
set, the USB will respond with a NAK handshake to any hub
endpoint 0 OUT tokens. Reset clears this bit.
1 = Data is ready to be received
0 = Not ready for data; respond with NAK
TPSIZ[3:0] — Hub Endpoint 0 Transmit Data Packet Size
These read/write bits store the number of transmit data bytes for the
next IN token request for hub endpoint 0. These bits are cleared by
reset.
14.6.8 USB Hub Endpoint 1 Control and Data Register (HCDR)
Address:
$005C
Bit 7
6
5
4
3
2
1
Bit 0
STALL1
PNEW
PCHG5
PCHG4
PCHG3
PCHG2
PCHG1
PCHG0
0
0
0
0
0
0
0
0
Read:
Write:
Reset:
Figure 14-10. USB Hub Endpoint 1 Control and Data Register (HCDR)
STALL1 — Hub Endpoint 1 Force Stall Bit
This read/write bit causes hub endpoint 1 to return a STALL
handshake when polled by the host. Reset clears this bit.
1 = Send STALL handshake
0 = Default
PNEW — Port New Status Change
This read/write bit enables a transmit to occur when the USB Host
controller sends an IN token to hub endpoint 1. Software should set
this bit when there is a status change on any of the downstream ports,
embedded device or hub. It must be cleared by software when there
Data Sheet
206
MC68HC908LD64 — Rev. 3.0
Universal Serial Bus Module (USB)
Freescale Semiconductor
Universal Serial Bus Module (USB)
Hub Function I/O Registers
is no status change to be reported to the host through endpoint 1. If
this bit is 0, a NAK handshake will be returned for next IN token for
hub endpoint 1. Reset clears this bit.
1 = Port status change bitmap is ready to be sent
0 = Port status does not change; respond with NAK
PCHG5–PCHG0 — Hub and Port Status Change Bitmap
These read/write bits report the status change for the hub, embedded
device and the four downstream ports. The status change bitmap is
returned to the host through the hub endpoint 1 if the PNEW bit is 1.
These bits are cleared by reset.
Bit Name
Function
PCHG0
Hub status change
PCHG1
PCHG2
PCHG3
PCHG4
PCHG5
Value
0
No status change in hub
1
Hub status change detected
0
No status change in Port 1
1
Port 1 status change detected
0
No status change in Port 2
1
Port 2 status change detected
0
No status change in Port 3
1
Port 3 status change detected
0
No status change in Port 4
1
Port 4 status change detected
0
No status change in
embedded device
1
Embedded device status
change detected
Port 1 status change
Port 2 status change
Port 3 status change
Port 4 status change
Embedded device
status change
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Description
Data Sheet
Universal Serial Bus Module (USB)
207
Universal Serial Bus Module (USB)
14.6.9 USB Hub Status Register (HSR)
Address:
Read:
$005D
Bit 7
6
5
4
3
2
1
Bit 0
RSEQ
SETUP
TX1ST
0
RPSIZ3
RPSIZ2
RPSIZ1
RPSIZ0
X
X
X
X
Write:
Reset:
TX1STR
X
X
X = Indeterminate
X
0
= Unimplemented
Figure 14-11. USB Hub Status Register (HSR)
RSEQ — Hub Endpoint 0 Receive Sequence Bit
This read-only bit indicates the type of data packet last received for
hub endpoint 0 (DATA0 or DATA1).
1 = DATA1 token received in last hub endpoint 0 receive
0 = DATA0 token received in last hub endpoint 0 receive
SETUP — Hub SETUP Token Detect Bit
This read-only bit indicates that a valid SETUP token has been
received.
1 = Last token received for hub endpoint 0 was a SETUP token
0 = Last token received for hub endpoint 0 was not a SETUP token
TX1ST — Hub Transmit First Flag
This read-only bit is set if the hub endpoint 0 data transmit flag (TXDF)
is set when the USB control logic is setting the hub endpoint 0 data
receive flag (RXDF). That is, TXDF is still set at the end of an
endpoint 0 reception. This bit allows the software to know that the
endpoint 0 transmission happened before the endpoint 0 reception.
Reset clears this bit.
1 = IN transaction occurred before SETUP/OUT
0 = IN transaction occurred after SETUP/OUT
TX1STR — Clear Hub Transmit First Flag
Writing a logic 1 to this write-only bit will clear the TX1ST bit if it is set.
Reset clears this bit.
1 = Write 1 to clear the TX1ST bit
0 = No effect
Data Sheet
208
MC68HC908LD64 — Rev. 3.0
Universal Serial Bus Module (USB)
Freescale Semiconductor
Universal Serial Bus Module (USB)
Embedded Device Function I/O Registers
RPSIZ[3:0] — Hub Endpoint 0 Receive Data Packet Size
These read-only bits store the number of data bytes received for the
last OUT or SETUP transaction for hub endpoint 0. These bits are not
affected by reset.
14.6.10 USB Hub Endpoint 0 Data Registers (HE0D0–HE0D7)
Address:
$0030–$0037
Bit 7
HE0D0–HE0D7
6
5
4
3
2
1
Bit 0
Read: HE0Rx7
HE0Rx6
HE0Rx5
HE0Rx4
HE0Rx3
HE0Rx2
HE0Rx1
HE0Rx0
Write: HE0Tx7
HE0Tx6
HE0Tx5
HE0Tx4
HE0Tx3
HE0Tx2
HE0Tx1
HE0Tx0
Reset:
Indeterminate after reset
Figure 14-12. USB Hub Endpoint 0 Data Registers (HE0D0–HE0D7)
HE0Rx[7:0] — Hub Endpoint 0 Receive Data Buffer
These read-only bits are serially loaded with OUT token or SETUP
token data directed at hub endpoint 0. The data is received by the D0+
and D0– pins.
HE0Tx[7:0] — Hub Endpoint 0 Transmit Data Buffer
These write-only buffers are loaded by software with data to be sent
on the USB bus on the next IN token directed at hub endpoint 0.
14.7 Embedded Device Function I/O Registers
The USB embedded device function provides a set of control/status
registers and twenty-four data registers that provide storage for the
buffering of data between the USB embedded device function and the
CPU.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Universal Serial Bus Module (USB)
209
Universal Serial Bus Module (USB)
14.7.1 USB Embedded Device Address Register (DADDR)
Address:
$0048
Bit 7
6
5
4
3
2
1
Bit 0
DEVEN
DADD6
DADD5
DADD4
DADD3
DADD2
DADD1
DADD0
0
0
0
0
0
0
0
0
Read:
Write:
Reset:
Figure 14-13. USB Embedded Device Address Register (DADDR)
DEVEN — Enable USB Embedded Device
These bit enable or disable the embedded device function. It is used
together with PEN1–PEN4 to control the enumeration sequence.
Reset clears these bits.
1 = USB Embedded Device enabled
0 = USB Embedded Device disabled
DADD[6:0] — USB Embedded Device Function Address
These bits specify the address of the embedded device function.
Reset clears these bits.
14.7.2 USB Embedded Device Interrupt Register 0 (DIR0)
Address:
Read:
$0049
Bit 7
6
5
4
TXD0F
RXD0F
0
0
3
2
TXD0IE
RXD0IE
Write:
Reset:
0
0
0
0
0
0
1
Bit 0
0
0
TXD0FR
RXD0FR
0
0
= Unimplemented
Figure 14-14. USB Embedded Device Interrupt Register 0 (DIR0)
TXD0F — Embedded Device Endpoint 0 Data Transmit Flag
This read-only bit is set after the data stored in embedded device
endpoint 0 transmit buffers have been sent and an ACK handshake
packet received from the host. Once the next set of data is ready in
the transmit buffers, software must clear this flag by writing a logic 1
to the TXD0FR bit. To enable the next data packet transmission,
Data Sheet
210
MC68HC908LD64 — Rev. 3.0
Universal Serial Bus Module (USB)
Freescale Semiconductor
Universal Serial Bus Module (USB)
Embedded Device Function I/O Registers
TX0E must also be set. If TXD0F bit is not cleared, a NAK handshake
will be returned in the next IN transaction. TXD0F generates an
interrupt request to the CPU if the TXD0IE bit is also set. Writing to
TXD0F has no effect. Reset clears this bit.
1 = Transmit on embedded device endpoint 0 has occurred
0 = Transmit on embedded device endpoint 0 has not occurred
RXD0F — Embedded Device Endpoint 0 Data Receive Flag
This read-only bit is set after the USB embedded device module has
received a data packet and responded with an ACK handshake
packet. Software must clear this flag by writing a logic 1 to the
RXD0FR bit after all data received have been read. To enable the
next data packet reception, RX0E must also be set. If RXD0F bit is not
cleared, a NAK handshake will be returned in the next OUT
transaction. RXD0F generates an interrupt request to CPU if the
RXD0IE bit is also set. Writing to RXD0F has no effect. Reset clears
this bit.
1 = Receive on embedded device endpoint 0 has occurred
0 = Receive on embedded device endpoint 0 has not occurred
TXD0IE — Embedded Device Endpoint 0 Transmit Interrupt Enable
This read/write bit enables the TXD0F bit to generate CPU interrupt
request when set. Reset clears the TXD0IE bit.
1 = TXD0F CPU interrupt requests enabled
0 = TXD0F CPU interrupt requests disabled
RXD0IE — Embedded Device Endpoint 0 Receive Interrupt Enable
This read/write bit enables the RXD0F bit to generate CPU interrupt
request when set. Reset clears the RXD0IE bit.
1 = RXD0F CPU interrupt requests enabled
0 = RXD0F CPU interrupt requests disabled
TXD0FR — Embedded Device Endpoint 0 Transmit Flag Reset
Writing a logic 1 to this write-only bit will clear the TXD0F bit if it is set.
Reset clears this bit.
1 = Write 1 to clear TXD0F bit
0 = No effect
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Universal Serial Bus Module (USB)
211
Universal Serial Bus Module (USB)
RXD0FR — Embedded Device Endpoint 0 Receive Flag Reset
Writing a logic 1 to this write-only bit will clear the RXD0F bit if it is set.
Reset clears this bit.
1 = Write 1 to clear RXD0F bit
0 = No effect
14.7.3 USB Embedded Device Interrupt Register 1 (DIR1)
Address:
Read:
$004A
Bit 7
6
5
4
TXD1F
0
0
0
3
2
1
Bit 0
0
0
0
TXD1IE
Write:
Reset:
TXD1FR
0
0
0
0
0
0
0
0
= Unimplemented
Figure 14-15. USB Embedded Device Interrupt Register 1 (DIR1)
TXD1F — Embedded Device Endpoint 1/2 Data Transmit Flag
This read-only bit is shared by endpoint 1 and endpoint 2 of the
embedded device. It is set after the data stored in the shared
endpoint 1/2 transmit buffer of the embedded device have been sent
and an ACK handshake packet received from the host. Once the next
set of data is ready in the transmit buffers, software must clear this
flag by writing a logic 1 to the TXD1FR bit. To enable the next data
packet transmission, TX1E must also be set. If TXD1F bit is not
cleared, a NAK handshake will be returned in the next IN transaction.
TXD1F generates an interrupt request to the CPU if the TXD1IE bit is
also set. Writing to TXD1F has no effect. Reset clears this bit.
1 = Transmit on endpoint 1 or endpoint 2 of the embedded device
has occurred
0 = Transmit on endpoint 1 or endpoint 2 of the embedded device
has not occurred
TXD1IE — Embedded Device Endpoint 1/2 Transmit Interrupt Enable
This read/write bit enables the TXD1F bit to generate CPU interrupt
request when set. Reset clears the TXD1IE bit.
1 = TXD1F CPU interrupt requests enabled
0 = TXD1F CPU interrupt requests disabled
Data Sheet
212
MC68HC908LD64 — Rev. 3.0
Universal Serial Bus Module (USB)
Freescale Semiconductor
Universal Serial Bus Module (USB)
Embedded Device Function I/O Registers
TXD1FR — Embedded Device Endpoint 1/2 Transmit Flag Reset
Writing a logic 1 to this write-only bit will clear the TXD1F bit if it is set.
Reset clears this bit.
1 = Write 1 to clear TXD1F
0 = No effect
14.7.4 USB Embedded Device Control Register 0 (DCR0)
Address:
$004B
Bit 7
6
5
4
3
2
1
Bit 0
T0SEQ
DSTALL0
TX0E
RX0E
TP0SIZ3
TP0SIZ2
TP0SIZ1
TP0SIZ0
0
0
0
0
0
0
0
0
Read:
Write:
Reset:
Figure 14-16. USB Embedded Device Control Register 0 (DCR0)
T0SEQ — Embedded Device Endpoint 0 Transmit Sequence Bit
This read/write bit determines which type of data packet (DATA0 or
DATA1) will be sent during the next IN transaction directed at
endpoint 0. Toggling of this bit must be controlled by software. Reset
clears this bit.
1 = DATA1 token active for next embedded device endpoint 0
transmit
0 = DATA0 token active for next embedded device endpoint 0
transmit
DSTALL0 — Embedded Device Endpoint 0 Force Stall Bit
This read/write bit causes embedded device endpoint 0 to return a
STALL handshake when polled by either an IN or OUT token by the
host. The USB hardware clears this bit when a SETUP token is
received. Reset clears this bit.
1 = Send STALL handshake
0 = Default
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Universal Serial Bus Module (USB)
213
Universal Serial Bus Module (USB)
TX0E — Embedded Device Endpoint 0 Transmit Enable
This read/write bit enables a transmit to occur when the USB host
controller sends an IN token to the embedded device endpoint 0.
Software should set this bit when data is ready to be transmitted. It
must be cleared by software when no more embedded device
endpoint 0 data needs to be transmitted. If this bit is 0 or the TXD0F
is set, the USB will respond with a NAK handshake to any embedded
device endpoint 0 IN tokens. Reset clears this bit.
1 = Data is ready to be sent
0 = Data is not ready; respond with NAK
RX0E — Embedded Device Endpoint 0 Receive Enable
This read/write bit enables a receive to occur when the USB host
controller sends an OUT token to the embedded device endpoint 0.
Software should set this bit when data is ready to be received. It must
be cleared by software when data cannot be received. If this bit is 0
or the RXD0F is set, the USB will respond with a NAK handshake to
any embedded device endpoint 0 OUT tokens. Reset clears this bit.
1 = Data is ready to be received
0 = Not ready for data; respond with NAK
TP0SIZ[3:0] — Embedded Device Endpoint 0 Transmit Data Packet Size
These read/write bits store the number of transmit data bytes for the
next IN token request for embedded device endpoint 0. These bits are
cleared by reset.
Data Sheet
214
MC68HC908LD64 — Rev. 3.0
Universal Serial Bus Module (USB)
Freescale Semiconductor
Universal Serial Bus Module (USB)
Embedded Device Function I/O Registers
14.7.5 USB Embedded Device Control Register 1 (DCR1)
Address:
$004C
Bit 7
6
5
T1SEQ
ENDADD
TX1E
0
0
0
Read:
4
3
2
1
Bit 0
TP1SIZ3
TP1SIZ2
TP1SIZ1
TP1SIZ0
0
0
0
0
0
Write:
Reset:
0
= Unimplemented
Figure 14-17. USB Embedded Device Control Register 1 (DCR1)
T1SEQ — Embedded Device Endpoint 1/2 Transmit Sequence Bit
This read/write bit determines which type of data packet (DATA0 or
DATA1) will be sent during the next IN transaction directed to
embedded device endpoint 1 or 2. Toggling of this bit must be
controlled by software. Reset clears this bit.
1 = DATA1 token active for next embedded device endpoint 1/2
transmit
0 = DATA0 token active for next embedded device endpoint 1/2
transmit
ENDADD — Endpoint Address Select
This read/write bit specifies whether the data inside the
DE1D0–DE1D7 registers are used for embedded device endpoint 1
or 2. If all the conditions for a successful endpoint 2 USB response to
a host’s IN token are satisfied (TXD1F=0, TX1E=1, DSTALL2=0, and
ENABLE2=1) except that the ENDADD bit is configured for
endpoint 1, the USB responds with a NAK handshake packet. Reset
clears this bit.
1 = The data buffers are used for embedded device endpoint 2
0 = The data buffers are used for embedded device endpoint 1
TX1E — Embedded Device Endpoint 1/2 Transmit Enable
This read/write bit enables a transmit to occur when the USB Host
controller sends an IN token to endpoint 1 or endpoint 2 of the
embedded device. The appropriate endpoint enable bit, ENABLE1 or
ENABLE2 bit in the DCR2 register, should also be set. Software
should set the TX1E bit when data is ready to be transmitted.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Universal Serial Bus Module (USB)
215
Universal Serial Bus Module (USB)
It must be cleared by software when no more data needs to be
transmitted. If this bit is 0 or the TXD1F is set, the USB will respond
with a NAK handshake to any endpoint 1 or endpoint 2 directed IN
tokens. Reset clears this bit.
1 = Data is ready to be sent.
0 = Data is not ready; respond with NAK.
TP1SIZ[3:0] — Embedded Device Endpoint 1/2 Transmit Data Packet Size
These read/write bits store the number of transmit data bytes for the
next IN token request for embedded device endpoint 1 or endpoint 2.
These bits are cleared by reset.
14.7.6 USB Embedded Device Control Register 2 (DCR2)
Address:
Read:
$0047
Bit 7
6
5
4
0
0
0
0
3
2
1
Bit 0
ENABLE2 ENABLE1 DSTALL2 DSTALL1
Write:
Reset:
0
0
0
0
0
0
0
0
= Unimplemented
Figure 14-18. USB Embedded Device Control Register 2 (DCR2)
ENABLE2 — Embedded Device Endpoint 2 Enable
This read/write bit enables embedded device endpoint 2 and allows
the USB to respond to IN packets addressed to this endpoint. Reset
clears this bit.
1 = Embedded device endpoint 2 is enabled and can respond to an
IN token
0 = Embedded device endpoint 2 is disabled
ENABLE1 — Embedded Device Endpoint 1 Enable
This read/write bit enables embedded device endpoint 1 and allows
the USB to respond to IN packets addressed to this endpoint. Reset
clears this bit.
1 = Embedded device endpoint 1 is enabled and can respond to an
IN token
0 = Embedded device endpoint 1 is disabled
Data Sheet
216
MC68HC908LD64 — Rev. 3.0
Universal Serial Bus Module (USB)
Freescale Semiconductor
Universal Serial Bus Module (USB)
Embedded Device Function I/O Registers
DSTALL2 — Embedded Device Endpoint 2 Force Stall Bit
This read/write bit causes embedded device endpoint 2 to return a
STALL handshake when polled by either an IN or OUT token by the
USB host controller. Reset clears this bit.
1 = Send STALL handshake
0 = Default
DSTALL1 — Embedded Device Endpoint 1 Force Stall Bit
This read/write bit causes embedded device endpoint 1 to return a
STALL handshake when polled by either an IN or OUT token by the
USB host controller. Reset clears this bit.
1 = Send STALL handshake
0 = Default
14.7.7 USB Embedded Device Status Register (DSR)
Address:
Read:
$004D
Bit 7
6
5
4
3
2
1
Bit 0
DRSEQ
DSETUP
DTX1ST
0
RP0SIZ3
RP0SIZ2
RP0SIZ1
RP0SIZ0
0
0
0
0
Write:
Reset:
DTX1STR
0
0
0
0
= Unimplemented
Figure 14-19. USB Embedded Device Status Register (DSR)
DRSEQ — Embedded Device Endpoint 0 Receive Sequence Bit
This read-only bit indicates the type of data packet last received for
embedded device endpoint 0 (DATA0 or DATA1).
1 = DATA1 token received in last embedded device endpoint 0
receive
0 = DATA0 token received in last embedded device endpoint 0
receive
DSETUP — Embedded Device SETUP Token Detect Bit
This read-only bit indicates that a valid SETUP token has been
received.
1 = Last token received for endpoint 0 was a SETUP token
0 = Last token received for endpoint 0 was not a SETUP token
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Universal Serial Bus Module (USB)
217
Universal Serial Bus Module (USB)
DTX1ST — Embedded Device Transmit First Flag
This read-only bit is set if the embedded device endpoint 0 data
transmit flag (TXD0F) is set when the USB control logic is setting the
embedded device endpoint 0 data receive flag (RXD0F). That is,
TXD0F is still set at the end of an endpoint 0 reception. This bit allows
the software to know that the endpoint 0 transmission happened
before the endpoint 0 reception. Reset clears this bit.
1 = IN transaction occurred before SETUP/OUT
0 = IN transaction occurred after SETUP/OUT
DTX1STR — Clear Transmit First Flag
Writing a logic 1 to this write-only bit will clear the DTX1ST bit if it is
set. Reset clears this bit.
1 = Write 1 to clear DTX1ST bit
0 = No effect
RP0SIZ[3:0] — Embedded Device Endpoint 0 Receive Data Packet Size
These read-only bits store the number of data bytes received for the
last OUT or SETUP transaction for embedded device endpoint 0.
These bits are not affected by reset.
Data Sheet
218
MC68HC908LD64 — Rev. 3.0
Universal Serial Bus Module (USB)
Freescale Semiconductor
Universal Serial Bus Module (USB)
Embedded Device Function I/O Registers
14.7.8 USB Embedded Device Endpoint 0 Data Registers (DE0D0–DE0D7)
Address:
$0020–$0027
Bit 7
DE0D0–DE0D7
6
5
4
3
2
1
Bit 0
Read: DE0Rx7
DE0Rx6
DE0Rx5
DE0Rx4
DE0Rx3
DE0Rx2
DE0Rx1
DE0Rx0
Write: DE0Tx7
DE0Tx6
DE0Tx5
DE0Tx4
DE0Tx3
DE0Tx2
DE0Tx1
DE0Tx0
Reset:
Indeterminate after reset
Figure 14-20. USB Embedded Device Endpoint 0 Data Registers
(DE0D0–DE0D7)
DE0Rx[7:0] — Embedded Device Endpoint 0 Receive Data Buffer
These read-only bits are serially loaded with OUT token or SETUP
token data directed at embedded device endpoint 0. The data is
received by the D0+ and D0– pins.
DE0Tx[7:0] — Embedded Device Endpoint 0 Transmit Data Buffer
These write-only buffers are loaded by software with data to be sent
on the USB bus on the next IN token directed at embedded device
endpoint 0.
14.7.9 USB Embedded Device Endpoint 1/2 Data Registers (DE1D0–DE1D7)
Address:
$0028–$002F
Bit 7
DE1D0–DE1D7
6
5
4
3
2
1
Bit 0
DE1Tx6
DE1Tx5
DE1Tx4
DE1Tx3
DE1Tx2
DE1Tx1
DE1Tx0
Read:
Write: DE1Tx7
Reset:
Indeterminate after reset
Figure 14-21. USB Embedded Device Endpoint 1/2 Data Registers
(DE1D0–DE1D7)
DE1Tx[7:0] — Embedded Device Endpoint 1/ Endpoint 2 Transmit Data
Buffer
These write-only buffers are loaded by software with data to be sent
on the USB bus on the next IN token directed at endpoint 1 or
endpoint 2 of the embedded device. These buffers are shared by
embedded device endpoints 1 and 2 and depend on proper
configuration of the ENDADD bit.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Universal Serial Bus Module (USB)
219
Universal Serial Bus Module (USB)
Data Sheet
220
MC68HC908LD64 — Rev. 3.0
Universal Serial Bus Module (USB)
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 15. Multi-Master IIC Interface (MMIIC)
15.1 Contents
15.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
15.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
15.4
I/O Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
15.5 Multi-Master IIC Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
15.5.1 Multi-Master IIC Address Register (MMADR) . . . . . . . . . . 224
15.5.2 Multi-Master IIC Control Register (MMCR) . . . . . . . . . . . . 225
15.5.3 Multi-Master IIC Master Control Register (MIMCR) . . . . . . 226
15.5.4 Multi-Master IIC Status Register (MMSR) . . . . . . . . . . . . . 228
15.5.5 Multi-Master IIC Data Transmit Register (MMDTR) . . . . . . 230
15.5.6 Multi-Master IIC Data Receive Register (MMDRR) . . . . . . 231
15.6
Programming Considerations . . . . . . . . . . . . . . . . . . . . . . . . . 232
15.2 Introduction
This Multi-master IIC (MMIIC) Interface is designed for internal serial
communication between the MCU and other IIC devices. A hardware
circuit generates "start" and "stop" signal, while byte by byte data
transfer is interrupt driven by the software algorithm. Therefore, it can
greatly help the software in dealing with other devices to have higher
system efficiency in a typical digital monitor system.
This module not only can be applied in internal communications, but can
also be used as a typical command reception serial bus for factory setup
and alignment purposes. It also provides the flexibility of hooking
additional devices to an existing system for future expansion without
adding extra hardware.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Multi-Master IIC Interface (MMIIC)
221
Multi-Master IIC Interface (MMIIC)
This Multi-master IIC module uses the IICSCL clock line and the IICSDA
data line to communicate with external DDC host or IIC interface. These
two pins are shared with port pins PTD6 and PTD7 respectively. The
outputs of IICSDA and IICSCL pins are open-drain type — no clamping
diode is connected between the pin and internal VDD. The maximum
data rate typically is 750k-bps. The maximum communication length and
the number of devices that can be connected are limited by a maximum
bus capacitance of 400pF.
15.3 Features
•
Compatibility with multi-master IIC bus standard
•
Software controllable acknowledge bit generation
•
Interrupt driven byte by byte data transfer
•
Calling address identification interrupt
•
Auto detection of R/W bit and switching of transmit or receive
mode
•
Detection of START, repeated START, and STOP signals
•
Auto generation of START and STOP condition in master mode
•
Arbitration loss detection and No-ACK awareness in master mode
•
8 selectable baud rate master clocks
•
Automatic recognition of the received acknowledge bit
15.4 I/O Pins
The MMIIC module uses two I/O pins, shared with standard port I/O pins.
The full name of the MMIIC I/O pins are listed in Table 15-1. The generic
pin name appear in the text that follows.
Table 15-1. Pin Name Conventions
MMIIC
Generic Pin Names:
Full MCU Pin Names:
Pin Selected for
IIC Function By:
SDA
PTD7/IICSDA
IICDATE bit in PDCR ($0069)
SCL
PTD6/IICSCL
IICSCLE bit in PDCR ($0069)
Data Sheet
222
MC68HC908LD64 — Rev. 3.0
Multi-Master IIC Interface (MMIIC)
Freescale Semiconductor
Multi-Master IIC Interface (MMIIC)
Multi-Master IIC Registers
Addr.
$006A
$006B
$006C
$006D
$006E
$006F
Register Name
Bit 7
6
4
3
2
1
Bit 0
MMAST
MMRW
MMBR2
MMBR1
MMBR0
0
0
0
0
0
0
MMAD6
MMAD5
MMAD4
MMAD3
MMAD2
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Read: MMALIF MMNAKIF
Multi-Master IIC
Master Control Register Write:
0
0
(MIMCR) Reset:
0
0
Read:
Multi-Master IIC Address
MMAD7
Register Write:
(MMADR)
Reset:
1
Read:
Multi-Master IIC Control
Register Write:
(MMCR) Reset:
MMEN
MMIEN
0
0
Multi-Master IIC Read: MMRXIF
Status Register Write:
0
(MMSR) Reset:
0
MMTXIF
5
MMBB
MMTXAK
0
MMATCH MMSRW MMRXAK
0
MMAD1 MMEXTAD
MMTXBE MMRXBF
0
Multi-Master IIC Read: MMTD7
Data Transmit Register Write:
(MMDTR) Reset:
1
Multi-Master IIC Read: MMRD7
Data Receive Register Write:
(MMDRR)
Reset:
0
0
0
0
1
0
1
0
MMTD6
MMTD5
MMTD4
MMTD3
MMTD2
MMTD1
MMTD0
1
1
1
1
1
1
1
MMRD6
MMRD5
MMRD4
MMRD3
MMRD2
MMRD1
MMRD0
0
0
0
0
0
0
0
= Unimplemented
Figure 15-1. MMIIC I/O Register Summary
15.5 Multi-Master IIC Registers
Six registers are associated with the Multi-master IIC module, they are
outlined in the following sections.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Multi-Master IIC Interface (MMIIC)
223
Multi-Master IIC Interface (MMIIC)
15.5.1 Multi-Master IIC Address Register (MMADR)
Address:
$006B
Bit 7
6
5
4
3
2
MMAD7
MMAD6
MMAD5
MMAD4
MMAD3
MMAD2
1
0
1
0
0
0
1
Bit 0
Read:
MMAD1 MMEXTAD
Write:
Reset:
0
0
Figure 15-2. Multi-Master IIC Address Register (MMADR)
MMAD[7:1] — Multi-Master Address
These seven bits can be the MMIIC interface’s own specific slave
address in slave mode or the calling address when in master mode.
Software must update it as the calling address while entering the
master mode and restore its own slave address after the master mode
is relinquished. Reset sets a default value of $A0.
MMEXTAD — Multi-Master Expanded Address
This bit is set to expand the address of the MMIIC in slave mode.
When set, the MMIIC will acknowledge the general call address $00
and the matched 4-bit address, MMAD[7:4]. Reset clears this bit.
For example, when MMADR is configured as:
MMAD7 MMAD6 MMAD5 MMAD4 MMAD3 MMAD2 MMAD1 MMEXTAD
1
1
0
1
X
X
X
1
The MMIIC module will respond to the calling address:
Bit 7
6
5
4
3
2
Bit 1
1
1
0
1
X
X
X
0
0
0
0
or the general calling address:
0
0
0
where X = don’t care; bit 0 of the calling address is the MMRW bit from
the calling master.
1 = MMIIC responds to address $00 and $MMAD[7:4]
0 = MMIIC responds to address $MMAD[7:1]
Data Sheet
224
MC68HC908LD64 — Rev. 3.0
Multi-Master IIC Interface (MMIIC)
Freescale Semiconductor
Multi-Master IIC Interface (MMIIC)
Multi-Master IIC Registers
15.5.2 Multi-Master IIC Control Register (MMCR)
Address:
$006C
Bit 7
6
MMEN
MMIEN
0
0
Read:
5
4
0
0
3
2
1
Bit 0
0
0
0
0
0
0
MMTXAK
Write:
Reset:
0
0
0
= Unimplemented
Figure 15-3. Multi-Master IIC Control Register (MMCR)
MMEN — Multi-Master IIC Enable
This bit is set to enable the Multi-master IIC module. When
MMEN = 0, module is disabled and all flags will restore to its poweron default states. Reset clears this bit.
1 = MMIIC module enabled
0 = MMIIC module disabled
MMIEN — Multi-Master IIC Interrupt Enable
When this bit is set, the MMTXIF, MMRXIF, MMALIF, and MMNAKIF
flags are enabled to generate an interrupt request to the CPU. When
MMIEN is cleared, the these flags are prevented from generating an
interrupt request. Reset clears this bit.
1 = MMTXIF, MMRXIF, MMALIF, and/or MMNAKIF bit set will
generate interrupt request to CPU
0 = MMTXIF, MMRXIF, MMALIF, and/or MMNAKIF bit set will not
generate interrupt request to CPU
MMTXAK — Transmit Acknowledge Enable
This bit is set to disable the MMIIC from sending out an acknowledge
signal to the bus at the 9th clock bit after receiving 8 data bits. When
MMTXAK is cleared, an acknowledge signal will be sent at the 9th
clock bit. Reset clears this bit.
1 = MMIIC does not send acknowledge signals at 9th clock bit
0 = MMIIC sends acknowledge signal at 9th clock bit
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Multi-Master IIC Interface (MMIIC)
225
Multi-Master IIC Interface (MMIIC)
15.5.3 Multi-Master IIC Master Control Register (MIMCR)
Address:
$006A
Bit 7
6
Read: MMALIF MMNAKIF
Write:
0
0
Reset:
0
0
5
4
3
2
1
Bit 0
MMAST
MMRW
MMBR2
MMBR1
MMBR0
0
0
0
0
0
MMBB
0
Figure 15-4. Multi-Master IIC Master Control Register (MIMCR)
MMALIF — Multi-Master Arbitration Lost Interrupt Flag
This flag is set when software attempt to set MMAST but the MMBB
has been set by detecting the start condition on the lines or when the
MMIIC is transmitting a "1" to SDA line but detected a "0" from SDA
line in master mode – an arbitration loss. This bit generates an
interrupt request to the CPU if the MMIEN bit in MMCR is also set.
This bit is cleared by writing "0" to it or by reset.
1 = Lost arbitration in master mode
0 = No arbitration lost
MMNAKIF — No Acknowledge Interrupt Flag
This flag is only set in master mode (MMAST = 1) when there is no
acknowledge bit detected after one data byte or calling address is
transferred. This flag also clears MMAST. MMNAKIF generates an
interrupt request to CPU if the MMIEN bit in MMCR is also set. This
bit is cleared by writing "0" to it or by reset.
1 = No acknowledge bit detected
0 = Acknowledge bit detected
MMBB — Bus Busy Flag
This flag is set after a start condition is detected (bus busy), and is
cleared when a stop condition (bus idle) is detected or the MMIIC is
disabled. Reset clears this bit.
1 = Start condition detected
0 = Stop condition detected or MMIIC is disabled
Data Sheet
226
MC68HC908LD64 — Rev. 3.0
Multi-Master IIC Interface (MMIIC)
Freescale Semiconductor
Multi-Master IIC Interface (MMIIC)
Multi-Master IIC Registers
MMAST — Master Control Bit
This bit is set to initiate a master mode transfer. In master mode, the
module generates a start condition to the SDA and SCL lines,
followed by sending the calling address stored in MMADR.
When the MMAST bit is cleared by MMNAKIF set (no acknowledge)
or by software, the module generates the stop condition to the lines
after the current byte is transmitted.
If an arbitration loss occurs (MMALIF = 1), the module reverts to slave
mode by clearing MMAST, and releasing SDA and SCL lines
immediately.
This bit is cleared by writing "0" to it or by reset.
1 = Master mode operation
0 = Slave mode operation
MMRW — Master Read/Write
This bit will be transmitted out as bit 0 of the calling address when the
module sets the MMAST bit to enter master mode. The MMRW bit
determines the transfer direction of the data bytes that follows. When
it is "1", the module is in master receive mode. When it is "0", the
module is in master transmit mode. Reset clears this bit.
1 = Master mode receive
0 = Master mode transmit
MMBR2–MMBR0 — Baud Rate Select
These three bits select one of eight clock rates as the master clock
when the module is in master mode.
Since this master clock is derived the CPU bus clock, the user
program should not execute the WAIT instruction when the MMIIC
module in master mode. This will cause the SDA and SCL lines to
hang, as the WAIT instruction places the MCU in wait mode, with CPU
clock is halted. These bits are cleared upon reset. (See Table 15-2 .
Baud Rate Select.)
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Multi-Master IIC Interface (MMIIC)
227
Multi-Master IIC Interface (MMIIC)
Table 15-2. Baud Rate Select
MMBR2
MMBR1
MMBR0
Baud Rate
0
0
0
750k
0
0
1
375k
0
1
0
187.5k
0
1
1
93.75k
1
0
0
46.875k
1
0
1
23.437k
1
1
0
11.719k
1
1
1
5.859k
NOTE:
CPU bus clock is external clock ÷ 4 = 6MHz
15.5.4 Multi-Master IIC Status Register (MMSR)
Address:
$006D
Bit 7
Read: MMRXIF
6
MMTXIF
Write:
0
0
Reset:
0
0
5
4
3
MMATCH MMSRW MMRXAK
0
0
1
2
0
0
1
Bit 0
MMTXBE MMRXBF
1
0
= Unimplemented
Figure 15-5. Multi-Master IIC Status Register (MMSR)
MMRXIF — Multi-Master IIC Receive Interrupt Flag
This flag is set after the data receive register (MMDRR) is loaded with
a new received data. Once the MMDRR is loaded with received data,
no more received data can be loaded to the MMDRR register until the
CPU reads the data from the MMDRR to clear MMRXBF flag.
MMRXIF generates an interrupt request to CPU if the MMIEN bit in
MMCR is also set. This bit is cleared by writing "0" to it or by reset; or
when the MMEN = 0.
1 = New data in data receive register (MMDRR)
0 = No data received
Data Sheet
228
MC68HC908LD64 — Rev. 3.0
Multi-Master IIC Interface (MMIIC)
Freescale Semiconductor
Multi-Master IIC Interface (MMIIC)
Multi-Master IIC Registers
MMTXIF — Multi-Master Transmit Interrupt Flag
This flag is set when data in the data transmit register (MMDTR) is
downloaded to the output circuit, and that new data can be written to
the MMDTR. MMTXIF generates an interrupt request to CPU if the
MMIEN bit in MMCR is also set. This bit is cleared by writing "0" to it
or when the MMEN = 0.
1 = Data transfer completed
0 = Data transfer in progress
MMATCH — Multi-Master Address Match
This flag is set when the received data in the data receive register
(MMDRR) is an calling address which matches with the address or its
extended addresses (MMEXTAD=1) specified in the MMADR
register.
1 = Received address matches MMADR
0 = Received address does not match
MMSRW — Multi-Master Slave Read/Write
This bit indicates the data direction when the module is in slave mode.
It is updated after the calling address is received from a master
device. MMSRW = 1 when the calling master is reading data from the
module (slave transmit mode). MMSRW = 0 when the master is
writing data to the module (receive mode).
1 = Slave mode transmit
0 = Slave mode receive
MMRXAK — Multi-Master Receive Acknowledge
When this bit is cleared, it indicates an acknowledge signal has been
received after the completion of 8 data bits transmission on the bus.
When MMRXAK is set, it indicates no acknowledge signal has been
detected at the 9th clock; the module will release the SDA line for the
master to generate "stop" or "repeated start" condition. Reset sets this
bit.
1 = No acknowledge signal received at 9th clock bit
0 = Acknowledge signal received at 9th clock bit
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Multi-Master IIC Interface (MMIIC)
229
Multi-Master IIC Interface (MMIIC)
MMTXBE — Multi-Master Transmit Buffer Empty
This flag indicates the status of the data transmit register (MMDTR).
When the CPU writes the data to the MMDTR, the MMTXBE flag will
be cleared. MMTXBE is set when MMDTR is emptied by a transfer of
its data to the output circuit. Reset sets this bit.
1 = Data transmit register empty
0 = Data transmit register full
MMRXBF — Multi-Master Receive Buffer Full
This flag indicates the status of the data receive register (MMDRR).
When the CPU reads the data from the MMDRR, the MMRXBF flag
will be cleared. MMRXBF is set when MMDRR is full by a transfer of
data from the input circuit to the MMDRR. Reset clears this bit.
1 = Data receive register full
0 = Data receive register empty
15.5.5 Multi-Master IIC Data Transmit Register (MMDTR)
Address:
$006E
Bit 7
6
5
4
3
2
1
Bit 0
MMTD7
MMTD6
MMTD5
MMTD4
MMTD3
MMTD2
MMTD1
MMTD0
1
1
1
1
1
1
1
1
Read:
Write:
Reset:
Figure 15-6. Multi-Master IIC Data Transmit Register (MMDTR)
When the MMIIC module is enabled, MMEN = 1, data written into this
register depends on whether module is in master or slave mode.
In slave mode, the data in MMDTR will be transferred to the output circuit
when:
•
the module detects a matched calling address (MMATCH = 1),
with the calling master requesting data (MMSRW = 1); or
•
the previous data in the output circuit has be transmitted and the
receiving master returns an acknowledge bit, indicated by a
received acknowledge bit (MMRXAK = 0).
Data Sheet
230
MC68HC908LD64 — Rev. 3.0
Multi-Master IIC Interface (MMIIC)
Freescale Semiconductor
Multi-Master IIC Interface (MMIIC)
Multi-Master IIC Registers
If the calling master does not return an acknowledge bit (MMRXAK = 1),
the module will release the SDA line for master to generate a "stop" or
"repeated start" condition. The data in the MMDTR will not be transferred
to the output circuit until the next calling from a master. The transmit
buffer empty flag remains cleared (MMTXBE = 0).
In master mode, the data in MMDTR will be transferred to the output
circuit when:
•
the module receives an acknowledge bit (MMRXAK = 0), after
setting master transmit mode (MMRW = 0), and the calling
address has been transmitted; or
•
the previous data in the output circuit has be transmitted and the
receiving slave returns an acknowledge bit, indicated by a
received acknowledge bit (MMRXAK = 0).
If the slave does not return an acknowledge bit (MMRXAK = 1), the
master will generate a "stop" or "repeated start" condition. The data in
the MMDTR will not be transferred to the output circuit. The transmit
buffer empty flag remains cleared (MMTXBE = 0).
The sequence of events for slave transmit and master transmit are
illustrated in Figure 15-8.
15.5.6 Multi-Master IIC Data Receive Register (MMDRR)
Address
:
$006F
Bit 7
6
5
4
3
2
1
Bit 0
Read: MMRD7 MMRD6 MMRD5 MMRD4 MMRD3 MMRD2 MMRD1 MMRD0
Write:
Reset:
0
0
0
0
0
0
0
0
= Unimplemente
d
Figure 15-7. Multi-Master IIC Data Receive Register (MMDRR)
When the MMIIC module is enabled, MMEN = 1, data in this read-only
register depends on whether module is in master or slave mode.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Multi-Master IIC Interface (MMIIC)
231
Multi-Master IIC Interface (MMIIC)
In slave mode, the data in MMDRR is:
•
the calling address from the master when the address match flag
is set (MMATCH = 1); or
•
the last data received when MMATCH = 0.
In master mode, the data in the MMDRR is:
•
the last data received.
When the MMDRR is read by the CPU, the receive buffer full flag is
cleared (MMRXBF = 0), and the next received data is loaded to the
MMDRR. Each time when new data is loaded to the MMDRR, the
MMRXIF interrupt flag is set, indicating that new data is available in
MMDRR.
The sequence of events for slave receive and master receive are
illustrated in Figure 15-8.
15.6 Programming Considerations
When the MMIIC module detects an arbitration loss in master mode, it
will release both SDA and SCL lines immediately. But if there are no
further STOP conditions detected, the module will hang up. Therefore, it
is recommended to have time-out software to recover from such ill
condition. The software can start the time-out counter by looking at the
MMBB (Bus Busy) flag in the MIMCR and reset the counter on the
completion of one byte transmission. If a time-out occur, software can
clear the MMEN bit (disable MMIIC module) to release the bus, and
hence clearing the MMBB flag. This is the only way to clear the MMBB
flag by software if the module hangs up due to a no STOP condition
received. The MMIIC can resume operation again by setting the MMEN
bit.
Data Sheet
232
MC68HC908LD64 — Rev. 3.0
Multi-Master IIC Interface (MMIIC)
Freescale Semiconductor
Multi-Master IIC Interface (MMIIC)
Programming Considerations
(a) Master Transmit Mode
START
Address
MMTXBE=0
MMRW=0
MMAST=1
Data1 → MMDTR
0
ACK
TX Data1
ACK
MMTXBE=1
MMTXIF=1
Data3 → MMDTR
MMTXBE=1
MMTXIF=1
Data2 → MMDTR
TX DataN
NAK
STOP
MMTXBE=1 MMNAKIF=1
MMTXIF=1 MMAST=0
DataN+2 → MMDTR MMTXBE=0
(b) Master Receive Mode
START
Address
1
ACK
RX Data1
ACK
Data1 → MMDRR
MMRXIF=1
MMRXBF=1
MMRXBF=0
MMRW=1
MMAST=1
MMTXBE=0
(dummy data → MMDTR)
RX DataN
NAK
STOP
DataN → MMDRR MMNAKIF=1
MMRXIF=1 MMAST=0
MMRXBF=1
(c) Slave Transmit Mode
START
Address
1
ACK
TX Data1
MMRXIF=1
MMRXBF=1
MMATCH=1
MMSRW=1
Data1 → MMDTR
MMTXBE=1
MMRXBF=0
ACK
MMTXBE=1
MMTXIF=1
Data2 → MMDTR
TX DataN
NAK
STOP
MMTXBE=1 MMNAKIF=1
MMTXIF=1 MMTXBE=0
DataN+2 → MMDTR
(d) Slave Receive Mode
START
Address
MMTXBE=0
MMRXBF=0
0
ACK
MMRXIF=1
MMRXBF=1
MMATCH=1
MMSRW=0
RX Data1
ACK
Data1 → MMDRR
MMRXIF=1
MMRXBF=1
RX DataN
NAK
STOP
DataN → MMDRR
MMRXIF=1
MMRXBF=1
KEY: shaded data packets indicate a transmit by the MCU’s MMIIC module
Figure 15-8. Data Transfer Sequences for Master/Slave Transmit/Receive Modes
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Multi-Master IIC Interface (MMIIC)
233
Multi-Master IIC Interface (MMIIC)
Data Sheet
234
MC68HC908LD64 — Rev. 3.0
Multi-Master IIC Interface (MMIIC)
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 16. DDC12AB Interface
16.1 Contents
16.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235
16.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
16.4
I/O Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
16.5
DDC Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238
16.6 DDC Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238
16.6.1 DDC Address Register (DDCADR) . . . . . . . . . . . . . . . . . . 238
16.6.2 DDC2 Address Register (DDC2ADR) . . . . . . . . . . . . . . . . 239
16.6.3 DDC Control Register (DDCCR) . . . . . . . . . . . . . . . . . . . . 240
16.6.4 DDC Master Control Register (DDCMCR) . . . . . . . . . . . . . 241
16.6.5 DDC Status Register (DDCSR) . . . . . . . . . . . . . . . . . . . . . 244
16.6.6 DDC Data Transmit Register (DDCDTR) . . . . . . . . . . . . . . 246
16.6.7 DDC Data Receive Register (DDCDRR) . . . . . . . . . . . . . . 247
16.7
Programming Considerations . . . . . . . . . . . . . . . . . . . . . . . . . 248
16.2 Introduction
This DDC12AB Interface module is used by the digital monitor to show
its identification information to the video controller. It contains DDC1
hardware and a two-wire, bidirectional serial bus which is fully
compatible with multi-master IIC bus protocol to support DDC2AB
interface.
This module not only can be applied in internal communications, but can
also be used as a typical command reception serial bus for factory setup
and alignment purposes. It also provides the flexibility of hooking
additional devices to an existing system for future expansion without
adding extra hardware.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
DDC12AB Interface
235
DDC12AB Interface
This DDC12AB module uses the DDCSCL clock line and the DDCSDA
data line to communicate with external DDC host or IIC interface. These
two pins are shared with port pins PTD4 and PTD5 respectively. The
outputs of DDCSDA and DDCSCL pins are open-drain type — no
clamping diode is connected between the pin and internal VDD. The
maximum data rate typically is 100k-bps. The maximum communication
length and the number of devices that can be connected are limited by
a maximum bus capacitance of 400pF.
16.3 Features
•
DDC1 hardware
•
Compatibility with multi-master IIC bus standard
•
Software controllable acknowledge bit generation
•
Interrupt driven byte by byte data transfer
•
Calling address identification interrupt
•
Auto detection of R/W bit and switching of transmit or receive
mode
•
Detection of START, repeated START, and STOP signals
•
Auto generation of START and STOP condition in master mode
•
Arbitration loss detection and No-ACK awareness in master mode
•
8 selectable baud rate master clocks
•
Automatic recognition of the received acknowledge bit
16.4 I/O Pins
The DDC12AB module uses two I/O pins, shared with standard port I/O
pins. The full name of the DDC12AB I/O pins are listed in Table 16-1.
The generic pin name appear in the text that follows.
Table 16-1. Pin Name Conventions
DDC12AB
Generic Pin Names:
Full MCU Pin Names:
Pin Selected for
DDC Function By:
SDA
PTD5/DDCSDA
DDCDATE bit in PDCR ($0069)
SCL
PTD4/DDCSCL
DDCSCLE bit in PDCR ($0069)
Data Sheet
236
MC68HC908LD64 — Rev. 3.0
DDC12AB Interface
Freescale Semiconductor
DDC12AB Interface
I/O Pins
Addr.
Register Name
$0016
DDC Master Control
Register
(DDCMCR)
Bit 7
6
5
4
3
2
1
Bit 0
Read:
ALIF
NAKIF
BB
Write:
0
0
MAST
MRW
BR2
BR1
BR0
Reset:
0
0
0
0
0
0
0
0
DAD7
DAD6
DAD5
DAD4
DAD3
DAD2
DAD1
EXTAD
1
0
1
0
0
0
0
0
0
0
DEN
DIEN
TXAK
SCLIEN
DDC1EN
Reset:
0
0
0
0
0
0
0
0
Read:
RXIF
TXIF
MATCH
SRW
RXAK
SCLIF
TXBE
RXBF
Write:
0
0
Reset:
0
0
0
0
1
0
1
0
DTD7
DTD6
DTD5
DTD4
DTD3
DTD2
DTD1
DTD0
Reset:
1
1
1
1
1
1
1
1
Read:
DRD7
DRD6
DRD5
DRD4
DRD3
DRD2
DRD1
DRD0
0
0
0
0
0
0
0
0
D2AD7
D2AD6
D2AD5
D2AD4
D2AD3
D2AD2
D2AD1
0
0
0
0
0
0
0
Read:
$0017
DDC Address Register
(DDCADR)
Write:
Reset:
Read:
$0018
$0019
$001A
$001B
DDC Control Register
(DDCCR)
DDC Status Register
(DDCSR)
DDC
Data Transmit Register
(DDCDTR)
DDC
Data Receive Register
(DDCDRR)
0
Write:
0
Read:
Write:
Write:
Reset:
Read:
$001C
DDC2 Address Register
(DDC2ADR)
0
Write:
Reset:
0
= Unimplemented
Figure 16-1. DDC I/O Register Summary
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
DDC12AB Interface
237
DDC12AB Interface
16.5 DDC Protocols
In DDC1 protocol communication, the module is in transmit mode. The
data written to the transmit register is continuously clocked out to the
SDA line by the rising edge of the Vsync input signal. During DDC1
communication, a falling transition on the SCL line can be detected to
generate an interrupt to the CPU for mode switching.
In DDC2AB protocol communication, the module can be either in
transmit mode or in receive mode, controlled by the calling master.
In DDC2 protocol communication, the module will act as a standard IIC
module, able to act as a master or a slave device.
16.6 DDC Registers
Seven registers are associated with the DDC module, they are outlined
in the following sections.
16.6.1 DDC Address Register (DDCADR)
Address:
$0017
Bit 7
6
5
4
3
2
1
Bit 0
DAD7
DAD6
DAD5
DAD4
DAD3
DAD2
DAD1
EXTAD
1
0
1
0
0
0
0
0
Read:
Write:
Reset:
Figure 16-2. DDC Address Register (DDCADR)
DAD[7:1] — DDC Address
These seven bits can be the DDC2 interface’s own specific slave
address in slave mode or the calling address when in master mode.
Software must update it as the calling address while entering the
master mode and restore its own slave address after the master mode
is relinquished. Reset sets a default value of $A0.
Data Sheet
238
MC68HC908LD64 — Rev. 3.0
DDC12AB Interface
Freescale Semiconductor
DDC12AB Interface
DDC Registers
EXTAD — DDC Expanded Address
This bit is set to expand the address of the DDC in slave mode. When
set, the DDC will acknowledge the general call address $00 and the
matched 4-bit address, DAD[7:4]. Reset clears this bit.
For example, when DDCADR is configured as:
DAD7
DAD6
DAD5
DAD4
DAD3
DAD2
DAD1
EXTAD
1
1
0
1
X
X
X
1
The DDC module will respond to the calling address:
Bit 7
6
5
4
3
2
Bit 1
1
1
0
1
X
X
X
0
0
0
0
or the general calling address:
0
0
0
where X = don’t care; bit 0 of the calling address is the MRW bit from
the calling master.
1 = DDC responds to address $00 and $DAD[7:4]
0 = DDC responds to address $DAD[7:1]
16.6.2 DDC2 Address Register (DDC2ADR)
Address:
$001C
Bit 7
6
5
4
3
2
1
D2AD7
D2AD6
D2AD5
D2AD4
D2AD3
D2AD2
D2AD1
0
0
0
0
0
0
0
Read:
Bit 0
0
Write:
Reset:
0
Figure 16-3. DDC2 Address Register (DDC2ADR)
D2AD[7:1] — DDC2 Address
These seven bits represent the second slave address for the DDC2BI
protocol. D2AD[7:1] should be set to the same value as DAD[7:1] in
DDCADR if user application do not use DDC2BI. Reset clears all bits
this register.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
DDC12AB Interface
239
DDC12AB Interface
16.6.3 DDC Control Register (DDCCR)
Address:
$0018
Bit 7
6
DEN
DIEN
0
0
Read:
5
4
0
0
3
2
1
TXAK
SCLIEN
DDC1EN
0
0
0
Bit 0
0
Write:
Reset:
0
0
0
= Unimplemented
Figure 16-4. DDC Control Register (DDCCR)
DEN — DDC Enable
This bit is set to enable the DDC module. When DEN = 0, module is
disabled and all flags will restore to its power-on default states. Reset
clears this bit.
1 = DDC module enabled
0 = DDC module disabled
DIEN — DDC Interrupt Enable
When this bit is set, the TXIF, RXIF, ALIF, and NAKIF flags are
enabled to generate an interrupt request to the CPU. When DIEN is
cleared, the these flags are prevented from generating an interrupt
request. Reset clears this bit.
1 = TXIF, RXIF, ALIF, and/or NAKIF bit set will generate interrupt
request to CPU
0 = TXIF, RXIF, ALIF, and/or NAKIF bit set will not generate
interrupt request to CPU
TXAK — Transmit Acknowledge Enable
This bit is set to disable the DDC from sending out an acknowledge
signal to the bus at the 9th clock bit after receiving 8 data bits. When
TXAK is cleared, an acknowledge signal will be sent at the 9th clock
bit. Reset clears this bit.
1 = DDC does not send acknowledge signals at 9th clock bit
0 = DDC sends acknowledge signal at 9th clock bit
Data Sheet
240
MC68HC908LD64 — Rev. 3.0
DDC12AB Interface
Freescale Semiconductor
DDC12AB Interface
DDC Registers
SCLIEN — SCL Interrupt Enable
When this bit is set, the SCLIF flag is enabled to generate an interrupt
request to the CPU. When SCLIEN is cleared, SCLIF is prevented
from generating an interrupt request. Reset clears this bit.
1 = SCLIF bit set will generate interrupt request to CPU
0 = SCLIF bit set will not generate interrupt request to CPU
DDC1EN — DDC1 Protocol Enable
This bit is set to enable DDC1 protocol. The DDC1 protocol will use
the Vsync input (from sync processor) as the master clock input to the
DDC module. Vsync rising-edge will continuously clock out the data
to the output circuit. No calling address comparison is performed. The
SRW bit in DDC status register (DDCSR) will always read as "1".
Reset clears this bit.
1 = DDC1 protocol enabled
0 = DDC1 protocol disabled
16.6.4 DDC Master Control Register (DDCMCR)
Address:
$0016
Bit 7
6
5
Read:
ALIF
NAKIF
BB
Write:
0
0
Reset:
0
0
0
4
3
2
1
Bit 0
MAST
MRW
BR2
BR1
BR0
0
0
0
0
0
Figure 16-5. DDC Master Control Register (DDCMCR)
ALIF — DDC Arbitration Lost Interrupt Flag
This flag is set when software attempt to set MAST but the BB has
been set by detecting the start condition on the lines or when the DDC
is transmitting a "1" to SDA line but detected a "0" from SDA line in
master mode – an arbitration loss. This bit generates an interrupt
request to the CPU if the DIEN bit in DDCCR is also set. This bit is
cleared by writing "0" to it or by reset.
1 = Lost arbitration in master mode
0 = No arbitration lost
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
DDC12AB Interface
241
DDC12AB Interface
NAKIF — No Acknowledge Interrupt Flag
This flag is only set in master mode (MAST = 1) when there is no
acknowledge bit detected after one data byte or calling address is
transferred. This flag also clears MAST. NAKIF generates an interrupt
request to CPU if the DIEN bit in DDCCR is also set. This bit is cleared
by writing "0" to it or by reset.
1 = No acknowledge bit detected
0 = Acknowledge bit detected
BB — Bus Busy Flag
This flag is set after a start condition is detected (bus busy), and is
cleared when a stop condition (bus idle) is detected or the DDC is
disabled. Reset clears this bit.
1 = Start condition detected
0 = Stop condition detected or DDC is disabled
MAST — Master Control Bit
This bit is set to initiate a master mode transfer. In master mode, the
module generates a start condition to the SDA and SCL lines,
followed by sending the calling address stored in DDCADR.
When the MAST bit is cleared by NAKIF set (no acknowledge) or by
software, the module generates the stop condition to the lines after
the current byte is transmitted.
If an arbitration loss occurs (ALIF = 1), the module reverts to slave
mode by clearing MAST, and releasing SDA and SCL lines
immediately.
This bit is cleared by writing "0" to it or by reset.
1 = Master mode operation
0 = Slave mode operation
MRW — Master Read/Write
This bit will be transmitted out as bit 0 of the calling address when the
module sets the MAST bit to enter master mode. The MRW bit
determines the transfer direction of the data bytes that follows. When
it is "1", the module is in master receive mode. When it is "0", the
module is in master transmit mode. Reset clears this bit.
1 = Master mode receive
0 = Master mode transmit
Data Sheet
242
MC68HC908LD64 — Rev. 3.0
DDC12AB Interface
Freescale Semiconductor
DDC12AB Interface
DDC Registers
BR2–BR0 — Baud Rate Select
These three bits select one of eight clock rates as the master clock
when the module is in master mode.
Since this master clock is derived the CPU bus clock, the user
program should not execute the WAIT instruction when the DDC
module in master mode. This will cause the SDA and SCL lines to
hang, as the WAIT instruction places the MCU in wait mode, with CPU
clock is halted. These bits are cleared upon reset. (See Table 16-2 .
Baud Rate Select.)
Table 16-2. Baud Rate Select
BR2
BR1
BR0
Baud Rate
0
0
0
100k
0
0
1
50k
0
1
0
25k
0
1
1
12.5k
1
0
0
6.25k
1
0
1
3.125k
1
1
0
1.56k
1
1
1
0.78k
NOTE:
CPU bus clock is external clock ÷ 4 = 6MHz
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
DDC12AB Interface
243
DDC12AB Interface
16.6.5 DDC Status Register (DDCSR)
Address:
$0019
Bit 7
6
5
4
3
2
1
Bit 0
Read:
RXIF
TXIF
MATCH
SRW
RXAK
SCLIF
TXBE
RXBF
Write:
0
0
Reset:
0
0
1
0
0
0
0
1
0
= Unimplemented
Figure 16-6. DDC Status Register (DDCSR)
RXIF — DDC Receive Interrupt Flag
This flag is set after the data receive register (DDCDRR) is loaded
with a new received data. Once the DDCDRR is loaded with received
data, no more received data can be loaded to the DDCDRR until the
CPU reads the data from the DDCDRR to clear RXBF flag. RXIF
generates an interrupt request to CPU if the DIEN bit in DDCCR is
also set. This bit is cleared by writing "0" to it or by reset; or when the
DEN = 0.
1 = New data in data receive register (DDCDRR)
0 = No data received
TXIF — DDC Transmit Interrupt Flag
This flag is set when data in the data transmit register (DDCDTR) is
downloaded to the output circuit, and that new data can be written to
the DDCDTR. TXIF generates an interrupt request to CPU if the DIEN
bit in DDCCR is also set. This bit is cleared by writing "0" to it or when
the DEN = 0.
1 = Data transfer completed
0 = Data transfer in progress
MATCH — DDC Address Match
This flag is set when the received data in the data receive register
(DDCDRR) is a calling address which matches with the address or its
extended addresses (EXTAD=1) specified in the DDCADR register.
1 = Received address matches DDCADR
0 = Received address does not match
Data Sheet
244
MC68HC908LD64 — Rev. 3.0
DDC12AB Interface
Freescale Semiconductor
DDC12AB Interface
DDC Registers
SRW — DDC Slave Read/Write
This bit indicates the data direction when the module is in slave mode.
It is updated after the calling address is received from a master
device. SRW = 1 when the calling master is reading data from the
module (slave transmit mode). SRW = 0 when the master is writing
data to the module (receive mode).
1 = Slave mode transmit
0 = Slave mode receive
RXAK — DDC Receive Acknowledge
When this bit is cleared, it indicates an acknowledge signal has been
received after the completion of 8 data bits transmission on the bus.
When RXAK is set, it indicates no acknowledge signal has been
detected at the 9th clock; the module will release the SDA line for the
master to generate "stop" or "repeated start" condition. Reset sets this
bit.
1 = No acknowledge signal received at 9th clock bit
0 = Acknowledge signal received at 9th clock bit
SCLIF — SCL Interrupt Flag
This flag is set when a falling edge is detected on the SCL line, only if
DDC1EN bit is set. SCLIF generates an interrupt request to CPU if the
SCLIEN bit in DDCCR is also set. SCLIF is cleared by writing "0" to it
or when the DCC1EN = 0, or DEN = 0. Reset clears this bit.
1 = Falling edge detected on SCL line
0 = No falling edge detected on SCL line
TXBE — DDC Transmit Buffer Empty
This flag indicates the status of the data transmit register (DDCDTR).
When the CPU writes the data to the DDCDTR, the TXBE flag will be
cleared. TXBE is set when DDCDTR is emptied by a transfer of its
data to the output circuit. Reset sets this bit.
1 = Data transmit register empty
0 = Data transmit register full
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
DDC12AB Interface
245
DDC12AB Interface
RXBF — DDC Receive Buffer Full
This flag indicates the status of the data receive register (DDCDRR).
When the CPU reads the data from the DDCDRR, the RXBF flag will
be cleared. RXBF is set when DDCDRR is full by a transfer of data
from the input circuit to the DDCDRR. Reset clears this bit.
1 = Data receive register full
0 = Data receive register empty
16.6.6 DDC Data Transmit Register (DDCDTR)
Address:
$001A
Bit 7
6
5
4
3
2
1
Bit 0
DTD7
DTD6
DTD5
DTD4
DTD3
DTD2
DTD1
DTD0
1
1
1
1
1
1
1
1
Read:
Write:
Reset:
Figure 16-7. DDC Data Transmit Register (DDCDTR)
When the DDC module is enabled, DEN = 1, data written into this
register depends on whether module is in master or slave mode.
In slave mode, the data in DDCDTR will be transferred to the output
circuit when:
•
the module detects a matched calling address (MATCH = 1), with
the calling master requesting data (SRW = 1); or
•
the previous data in the output circuit has be transmitted and the
receiving master returns an acknowledge bit, indicated by a
received acknowledge bit (RXAK = 0).
If the calling master does not return an acknowledge bit (RXAK = 1), the
module will release the SDA line for master to generate a "stop" or
"repeated start" condition. The data in the DDCDTR will not be
transferred to the output circuit until the next calling from a master. The
transmit buffer empty flag remains cleared (TXBE = 0).
In master mode, the data in DDCDTR will be transferred to the output
circuit when:
Data Sheet
246
MC68HC908LD64 — Rev. 3.0
DDC12AB Interface
Freescale Semiconductor
DDC12AB Interface
DDC Registers
•
the module receives an acknowledge bit (RXAK = 0), after
setting master transmit mode (MRW = 0), and the calling address
has been transmitted; or
•
the previous data in the output circuit has be transmitted and the
receiving slave returns an acknowledge bit, indicated by a
received acknowledge bit (RXAK = 0).
If the slave does not return an acknowledge bit (RXAK = 1), the master
will generate a "stop" or "repeated start" condition. The data in the
DDCDTR will not be transferred to the output circuit. The transmit buffer
empty flag remains cleared (TXBE = 0).
The sequence of events for slave transmit and master transmit are
illustrated in Figure 16-9.
16.6.7 DDC Data Receive Register (DDCDRR)
Address:
Read:
$001B
Bit 7
6
5
4
3
2
1
Bit 0
DRD7
DRD6
DRD5
DRD4
DRD3
DRD2
DRD1
DRD0
0
0
0
0
0
0
0
0
Write:
Reset:
= Unimplemented
Figure 16-8. DDC Data Receive Register (DDCDRR)
When the DDC module is enabled, DEN = 1, data in this read-only
register depends on whether module is in master or slave mode.
In slave mode, the data in DDCDRR is:
•
the calling address from the master when the address match flag
is set (MATCH = 1); or
•
the last data received when MATCH = 0.
In master mode, the data in the DDCDRR is:
•
the last data received.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
DDC12AB Interface
247
DDC12AB Interface
When the DDCDRR is read by the CPU, the receive buffer full flag is
cleared (RXBF = 0), and the next received data is loaded to the
DDCDRR. Each time when new data is loaded to the DDCDRR, the
RXIF interrupt flag is set, indicating that new data is available in
DDCDRR.
The sequence of events for slave receive and master receive are
illustrated in Figure 16-9.
16.7 Programming Considerations
When the DDC module detects an arbitration loss in master mode, it will
release both SDA and SCL lines immediately. But if there are no further
STOP conditions detected, the module will hang up. Therefore, it is
recommended to have time-out software to recover from such ill
condition. The software can start the time-out counter by looking at the
BB (Bus Busy) flag in the DDCMCR and reset the counter on the
completion of one byte transmission. If a time-out occur, software can
clear the DEN bit (disable DDC module) to release the bus, and hence
clearing the BB flag. This is the only way to clear the BB flag by software
if the module hangs up due to a no STOP condition received. The DDC
can resume operation again by setting the DEN bit.
Data Sheet
248
MC68HC908LD64 — Rev. 3.0
DDC12AB Interface
Freescale Semiconductor
DDC12AB Interface
Programming Considerations
(a) Master Transmit Mode
START
Address
TXBE=0
MRW=0
MAST=1
Data1 → DDCDTR
0
ACK
TX Data1
TXBE=1
TXIF=1
Data2 → DDCDTR
ACK
TXBE=1
TXIF=1
Data3 → DDCDTR
TX DataN
NAK
STOP
TXBE=1 NAKIF=1
TXIF=1 MAST=0
DataN+2 → DDCDTR TXBE=0
(b) Master Receive Mode
START
Address
1
ACK
RX Data1
ACK
Data1 → DDCDRR
RXIF=1
RXBF=1
RXBF=0
MRW=1
MAST=1
TXBE=0
(dummy data → DDCDTR)
RX DataN
DataN → DDCDRR
RXIF=1
RXBF=1
NAK
STOP
NAKIF=1
MAST=0
(c) Slave Transmit Mode
START
Address
1
ACK
TX Data1
ACK
RXIF=1
TXBE=1
RXBF=1
TXIF=1
MATCH=1
Data2 → DDCDTR
SRW=1
Data1 → DDCDTR
TXBE=1
RXBF=0
TX DataN
TXBE=1
TXIF=1
DataN+2 → DDCDTR
NAK
STOP
NAKIF=1
TXBE=0
(d) Slave Receive Mode
START
Address
TXBE=0
RXBF=0
0
ACK
RXIF=1
RXBF=1
MATCH=1
SRW=0
RX Data1
ACK
Data1 → DDCDRR
RXIF=1
RXBF=1
RX DataN
NAK
STOP
DataN → DDCDRR
RXIF=1
RXBF=1
KEY: shaded data packets indicate a transmit by the MCU’s DDC module
Figure 16-9. Data Transfer Sequences for Master/Slave Transmit/Receive Modes
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
DDC12AB Interface
249
DDC12AB Interface
Data Sheet
250
MC68HC908LD64 — Rev. 3.0
DDC12AB Interface
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 17. Sync Processor
17.1 Contents
17.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
17.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
17.4
I/O Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253
17.5 Functional Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
17.5.1 Polarity Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
17.5.1.1
Hsync Polarity Detection . . . . . . . . . . . . . . . . . . . . . . . . 256
17.5.1.2
Vsync Polarity Detection . . . . . . . . . . . . . . . . . . . . . . . . 256
17.5.1.3
Composite Sync Polarity Detection . . . . . . . . . . . . . . . . 256
17.5.2 Sync Signal Counters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
17.5.3 Polarity Controlled HOUT and VOUT Outputs . . . . . . . . . . 257
17.5.4 Clamp Pulse Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258
17.5.5 Low Vertical Frequency Detect . . . . . . . . . . . . . . . . . . . . . 259
17.6 Sync Processor I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . 259
17.6.1 Sync Processor Control & Status Register (SPCSR). . . . . 259
17.6.2 Sync Processor Input/Output Control Register (SPIOCR) . 261
17.6.3 Vertical Frequency Registers (VFRs). . . . . . . . . . . . . . . . . 263
17.6.4 Hsync Frequency Registers (HFRs). . . . . . . . . . . . . . . . . . 265
17.6.5 Sync Processor Control Register 1 (SPCR1). . . . . . . . . . . 267
17.6.6 H & V Sync Output Control Register (HVOCR) . . . . . . . . . 268
17.7
System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .269
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Sync Processor
251
Sync Processor
17.2 Introduction
The Sync Processor is designed to detect and process sync signals
inside a digital monitor system — from separated Hsync and Vsync
inputs. After detection and the necessary polarity correction and/or sync
separation, the corrected sync signals are sent out. The MCU can also
send commands to other monitor circuitry, such as for the geometry
correction and OSD, using the DDC12AB and/or the IIC communication
channels.
The block diagram of the Sync Processor is shown in Figure 17-2.
NOTE:
All quoted timings in this section assume an internal bus frequency of
6MHz.
17.3 Features
Features of the Sync Processor include the following:
•
Polarity detector
•
Horizontal frequency counter
•
Vertical frequency counter
•
Low vertical frequency indicator (40.7Hz)
•
Polarity controlled HOUT and VOUT outputs:
– From separate Hsync and Vsync
– From composite sync on HSYNC input pin
– From internal selectable free running Hsync and Vsync pulses
•
Free-running Hsync, Vsync, DE, and DCLK of 4 video modes
•
CLAMP pulse output to the external pre-amp chip
•
Internal schmitt trigger on HSYNC, and VSYNC input pins to
improve noise immunity
Data Sheet
252
MC68HC908LD64 — Rev. 3.0
Sync Processor
Freescale Semiconductor
Sync Processor
I/O Pins
17.4 I/O Pins
The Sync Processor uses seven I/O pins, with four pins shared with
standard port I/O pins and one pin shared with timer channel 0. The full
name of the Sync Processor I/O pins are listed in Table 17-1. The
generic pin name appear in the text that follows.
Table 17-1. Pin Name Conventions
Sync Processor
Generic Pin Names:
Full MCU Pin Names:
Pin Selected for
Sync Processor Function By:
HSYNC
HSYNC
—
VSYNC
VSYNC
—
HOUT
PTD3/HOUT
HOUTE bit in PDCR ($0069)
VOUT
PTD2/VOUT
VOUTE bit in PDCR ($0069)
DE
PTD1/DE
DEE bit in PDCR ($0069)
DCLK
PTD0/DCLK
DCLKE bit in PDCR ($0069)
CLAMP
CLAMP/TCH0
ELS0B and ELS0A bits in TSC0 ($0010)
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Sync Processor
253
Sync Processor
Addr.
$0040
$0041
$0042
$0043
$0044
Register Name
Read:
Sync Processor Control
and Status Register Write:
(SPCSR)
Reset:
Bit 7
6
VSIE
VEDGE
5
4
3
2
COMP
VINVO
HINVO
VSIF
1
Bit 0
VPOL
HPOL
0
0
0
0
0
0
0
0
0
Read:
Vertical Frequency High
Register Write:
(VFHR)
Reset:
VOF
0
0
VF12
VF11
VF10
VF9
VF8
CPW1
CPW0
0
0
0
0
0
0
0
0
Read:
Vertical Frequency Low
Register Write:
(VFLR)
Reset:
VF7
VF6
VF5
VF4
VF3
VF2
VF1
VF0
0
0
0
0
0
0
0
0
Read:
Hsync Frequency High
Register Write:
(HFHR)
Reset:
HFH7
HFH6
HFH5
HFH4
HFH3
HFH2
HFH1
HFH0
0
0
0
0
0
0
0
0
0
0
HFL4
HFL3
HFL2
HFL1
HFL0
0
0
0
0
0
0
0
COINV
R
R
R
BPOR
SOUT
0
0
ATPOL
FSHF
0
0
Read: HOVER
Hsync Frequency Low
Register Write:
(HFLR)
Reset:
0
Read: VSYNCS HSYNCS
$0045
$0046
Sync Processor I/O Control
Write:
Register (SPIOCR)
Reset:
Read:
Sync Processor Control
Register 1 Write:
(SPCR1)
Reset:
0
0
0
LVSIF
LVSIE
HPS1
HPS0
0
0
R
R
0
0
0
Read:
H&V Sync Output Control
$003F
Register Write:
(HVOCR)
Reset:
DCLKPH1 DCLKPH0
0
= Unimplemented
R
0
R
HVOCR1 HVOCR0
0
0
= Reserved
Figure 17-1. Sync Processor I/O Register Summary
Data Sheet
254
MC68HC908LD64 — Rev. 3.0
Sync Processor
Freescale Semiconductor
Sync Processor
Functional Blocks
17.5 Functional Blocks
EXTRACTED
VSYNC
SVF
A
1
VOUT
B S
B S
VSYNC
VINVO
A1
SOUT
COMP
VSIF
POLARITY DETECT
VPOL
VSIE
EDGE DETECT
ONE SHOT
VEDGE
VFLR
INTERNAL
BUS CLOCK
6MHz
125kHz
÷ 48
VFHR
VOF
OVERFLOW DETECT
13-BIT COUNTER
$C00 DETECT
TO INTERRUPT
LOGIC
LVSIF
LVSIE
ONE SHOT
HFLR
CLK32/32.768
HFHR
12-BIT COUNTER
HSYNC
POLARITY DETECT
VPOL
DE
B
A1 S
HOVER
OVERFLOW DETECT
HPOL
COMP
EXTRACTED VSYNC
VSYNC EXTRACTOR
DCLK
SVF
BPOR
DCLK1
FROM CGM
H/V SYNC, DE, DCLK
PULSE GENERATOR
HVOCR[1:0]
DCLKPH[1:0]
SHF
B
COINV
CLAMP
PULSE GENERATOR
CLAMP
A1 S
SOUT
HINVO
HOUT
Figure 17-2. Sync Processor Block Diagram
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Sync Processor
255
Sync Processor
17.5.1 Polarity Detection
17.5.1.1 Hsync Polarity Detection
The Hsync polarity detection circuit measures the length of high and low
period of the HSYNC input. If the length of high is longer than L and the
length of low is shorter than S, the HPOL bit will be "0", indicating a
negative polarity HSYNC input. If the length of low is longer than L and
the length of high is shorter than S, the HPOL bit will be "1", indicating a
positive polarity HSYNC input. The table below shows three possible
cases for HSYNC polarity detection — the conditions are selected by the
HPS[1:0] bits in the Sync Processor Control Register 1 (SPCR1).
Polarity Detection Pulse Width
SPCR1 ($0046)
Long is greater than (L)
Short is less than (S)
HPS1
HPS0
7µs
6µs
0
0
3.5µs
3µs
1
X
14µs
12µs
0
1
17.5.1.2 Vsync Polarity Detection
The Vsync polarity detection circuit performs a similar function as for
Hsync. If the length of high is longer than 4ms and the length of low is
shorter than 2ms, the VPOL bit will be "0", indicating a negative polarity
VSYNC input. If the length of low is longer than 4ms and the length of
high is shorter than 2ms, the VPOL bit will be "1", indicating a positive
polarity VSYNC input.
17.5.1.3 Composite Sync Polarity Detection
When a composite sync signal is the input (COMP = 1 for composite
sync processing), the HPOL bit = VPOL bit, and the polarity is detected
using the VSYNC polarity detection criteria described in section
17.5.1.2 .
Data Sheet
256
MC68HC908LD64 — Rev. 3.0
Sync Processor
Freescale Semiconductor
Sync Processor
Functional Blocks
17.5.2 Sync Signal Counters
There are two counters: a 13-bit horizontal frequency counter to count
the number of horizontal sync pulses within a 32ms or 8ms period; and
a 13-bit vertical frequency counter to count the number of system clock
cycles between two vertical sync pulses. These two data can be read by
the CPU to check the signal frequencies and to determine the video
mode.
The 13-bit vertical frequency register encompasses vertical frequency
range from approximately 15Hz to 128kHz. Due to the asynchronous
timing between the incoming VSYNC signal and internal system clock,
there will be ±1 count error on reading the Vertical Frequency Registers
(VFRs) for the same vertical frequency.
The horizontal counter counts the pulses on HSYNC pin input, and is
uploaded to the Hsync Frequency Registers (HFRs) every 32.768ms or
8.192ms.
17.5.3 Polarity Controlled HOUT and VOUT Outputs
The processed sync signals are output on HOUT and VOUT when the
corresponding bits in Configuration Register 0 ($0069) are set. The
signal to these output pins depend on SOUT and COMP bits (see Table
17-2), with polarity controlled by ATPOL, HINVO, and VINVO bits as
shown in Table 17-3.
Table 17-2. Sync Output Control
Sync Outputs:
VOUT and HOUT
SOUT
COMP
1
X
Free-running video mode output
0
0
Sync outputs follow sync inputs VSYNC and HSYNC
respectively, with polarity correction shown in Table 17-3.
0
1
HOUT follows the composite sync input and VOUT is the
extracted Vsync (3 to 14µs delay to composite input), with
polarity correction shown in Table 17-3.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Sync Processor
257
Sync Processor
Table 17-3. Sync Output Polarity
ATPOL
SOUT
VINVO
or
HINVO
X
1
X
Free-running video mode output
0
0
0
Same polarity as sync input
0
0
1
Inverted polarity of sync input
1
0
0
Negative polarity sync output
1
0
1
Positive polarity sync output
Sync Outputs:
VOUT/HOUT
When the SOUT bit is set, the HOUT output is a free-running pulse. Both
HOUT and VOUT outputs are negative polarity, with frequencies
selected by the H & V Sync Output Control Register (HVOCR).
17.5.4 Clamp Pulse Output
When the ELS0B and ELS0A bits in the TSC0 register are logic 0 (see
Table 11-3), a clamp signal is output on the CLAMP pin. This clamp
pulse is triggered either on the leading edge or the trailing edge of
HSYNC, controlled by BPOR bit, with the polarity controlled by the
COINV bit. See Figure 17-3 . Clamp Pulse Output Timing.
HSYNC
(HPOL = 1)
CLAMP
(BPOR = 0)
Pulse width = 0.33~2.1µs
CLAMP
(BPOR = 1)
Pulse width = 0.33~2.1µs
HSYNC
(HPOL = 0)
CLAMP
(BPOR = 0)
Pulse width = 0.33~2.1µs
CLAMP
(BPOR = 1)
Pulse width = 0.33~2.1µs
Figure 17-3. Clamp Pulse Output Timing
Data Sheet
258
MC68HC908LD64 — Rev. 3.0
Sync Processor
Freescale Semiconductor
Sync Processor
Sync Processor I/O Registers
17.5.5 Low Vertical Frequency Detect
Logic monitors the value of the Vsync Frequency Register (VFR), and
sets the low vertical frequency flag (LVSIF) when the value of VFR is
higher than $C00 (frequency below 40.7Hz). LVSIF bit can generate an
interrupt request to the CPU when the LVSIE bit is set and I-bit in the
Condition Code Register is "0". The LVSIF bit can help the system to
detect video off mode fast.
17.6 Sync Processor I/O Registers
Eight registers are associated with the Sync Processor, they outlined in
the following sections.
17.6.1 Sync Processor Control & Status Register (SPCSR)
Address:
$0040
Bit 7
6
VSIE
VEDGE
Read:
4
3
2
COMP
VINVO
HINVO
0
0
0
VSIF
Write:
Reset:
5
1
Bit 0
VPOL
HPOL
0
0
0
0
0
0
= Unimplemented
Figure 17-4. Sync Processor Control & Status Register (SPCSR)
VSIE — VSync Interrupt Enable
When this bit is set, the VSIF flag is enabled to generate an interrupt
request to the CPU. When VSIE is cleared, the VSIF flag is prevented
from generating an interrupt request to the CPU. Reset clears this bit.
1 = VSIF bit set will generate interrupt request to CPU
0 = VSIF bit set does not generate interrupt request to CPU
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Sync Processor
259
Sync Processor
VEDGE — VSync Interrupt Edge Select
This bit specifies the triggering edge of Vsync interrupt. When it is "0",
the rising edge of internal Vsync signal which is either from the
VSYNC pin or extracted from the composite input signal will set VSIF
flag. When it is "1", the falling edge of internal Vsync signal will set
VSIF flag. Reset clears this bit.
1 = VSIF bit will be set by falling edge of Vsync
0 = VSIF bit will be set by rising edge of Vsync
VSIF — VSync Interrupt Flag
This flag is only set by the specified edge of the internal Vsync signal,
which is either from the VSYNC input pin or extracted from the
composite sync input signal. The triggering edge is specified by the
VEDGE bit. VSIF generates an interrupt request to the CPU if the
VSIE bit is also set. This bit is cleared by writing a "0" to it or by a reset.
1 = A valid edge is detected on the Vsync
0 = No valid Vsync is detected
COMP — Composite Sync Input Enable
This bit is set to enable the separator circuit which extracts the Vsync
pulse from the composite sync input on HSYNC. The extracted Vsync
signal is used as it were from the VSYNC input. Reset clears this bit.
1 = Composite sync input enabled
0 = Composite sync input disabled
VINVO — VOUT Signal Polarity
This bit, together with the ATPOL bit in SPCR1 controls the output
polarity of the VOUT signal (see Table 17-4).
HINVO — HOUT Signal Polarity
This bit, together with the ATPOL bit in SPCR1 controls the output
polarity of the HOUT signal (see Table 17-4).
Data Sheet
260
MC68HC908LD64 — Rev. 3.0
Sync Processor
Freescale Semiconductor
Sync Processor
Sync Processor I/O Registers
Table 17-4. ATPOL, VINVO, and HINVO setting
Sync Outputs:
VOUT/HOUT
ATPOL
VINVO / HINVO
0
0
Same polarity as sync input
0
1
Inverted polarity of sync input
1
0
Negative polarity sync output
1
1
Positive polarity sync output
VPOL — Vsync Input Polarity
This bit indicates the polarity of the VSYNC input, or the extracted
Vsync from a composite sync input (COMP=1). Reset clears this bit.
1 = Vsync is positive polarity
0 = Vsync is negative polarity
HPOL — Hsync Input Polarity
This bit indicates the polarity of the HSYNC input. This bit equals the
VPOL bit when the COMP bit is set. Reset clears this bit.
1 = Hsync is positive polarity
0 = Hsync is negative polarity
17.6.2 Sync Processor Input/Output Control Register (SPIOCR)
Address:
$0045
Bit 7
6
5
4
3
2
1
Bit 0
COINV
R
R
R
BPOR
SOUT
0
0
Read: VSYNCS HSYNCS
Write:
Reset:
0
0
0
= Unimplemented
R
= Reserved
Figure 17-5. Sync Processor Input/Output Control Register (SPIOCR)
VSYNCS — VSYNC Input State
This read-only bit reflects the logical state of the VSYNC input.
HSYNCS — HSYNC Input State
This read-only bit reflects the logical state of the HSYNC input.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Sync Processor
261
Sync Processor
COINV — Clamp Output Invert
This bit is set to invert the clamp pulse output to negative. Reset
clears this bit.
1 = Clamp output is set for negative pulses
0 = Clamp output is set for positive pulses
BPOR — Back Porch
This bit defines the triggering edge of the clamp pulse output relative
to the HSYNC input. Reset clears this bit.
1 = Clamp pulse is generated on the trailing edge of HSYNC
0 = Clamp pulse is generated on the leading edge of HSYNC
SOUT — Sync Output Enable
This bit will select the output signals for the VOUT and HOUT pins and
generate the DE and DCLK signals to the pins. Reset clears this bit.
1 = VOUT, HOUT, DE, and DCLK outputs are internally generated
free-running timing pulses with frequencies determined by
HVCOR[1:0] bits in HVCOR and CGM values.
0 = VOUT and HOUT outputs are processed VSYNC and HSYNC
inputs respectively and DE and DCLK are hold as logic low.
Data Sheet
262
MC68HC908LD64 — Rev. 3.0
Sync Processor
Freescale Semiconductor
Sync Processor
Sync Processor I/O Registers
17.6.3 Vertical Frequency Registers (VFRs)
This register pair contains the 13-bit vertical frequency count value, an
overflow bit, and the clamp pulse width selection bits.
Address:
Read:
$0041
Bit 7
6
5
4
3
2
1
Bit 0
VOF
0
0
VF12
VF11
VF10
VF9
VF8
CPW1
CPW0
0
0
0
0
0
0
0
Write:
Reset:
0
Figure 17-6. Vertical Frequency High Register
Address:
Read:
$0042
Bit 7
6
5
4
3
2
1
Bit 0
VF7
VF6
VF5
VF4
VF3
VF2
VF1
VF0
0
0
0
0
0
0
0
0
Write:
Reset:
= Unimplemented
Figure 17-7. Vertical Frequency Low Register
VF[12:0] — Vertical Frame Frequency
This read-only 13-bit contains information of the vertical frame
frequency. An internal 13-bit counter counts the number of 8µs
periods between two Vsync pulses. The most significant 5 bits of the
counted value is transferred to the high byte register, and the least
significant 8 bits is transferred to an intermediate buffer. When the
high byte register is read, the 8-bit counted value stored in the
intermediate buffer will be uploaded to the low byte register.
Therefore, user program must read the high byte register first, then
low byte register in order to get the complete counted value of one
vertical frame. If the counter overflows, the overflow flag, VOF, will be
set, indicating the counter value stored in the VFRs is meaningless.
The data corresponds to the period of one vertical frame. This register
can be read to determine if the frame frequency is valid, and to
determine the video mode.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Sync Processor
263
Sync Processor
The frame frequency is calculated by:
1
Vertical Frame Frequency = --------------------------------------------------VFR ± 1 × 48 × t CYC
1
= -------------------------------------VFR ± 1 × 8µ s
for internal bus clock of 6MHz
Table 17-5 shows examples for the Vertical Frequency Register, all VFR
numbers are in hexadecimal.
Table 17-5. Sample Vertical Frame Frequencies
VFR
Max Freq.
Min Freq.
VFR
Max Freq.
Min Freq.
$02A0
186.20 Hz
185.70 Hz
$0780
65.10 Hz
65.00 Hz
$03C0
130.34 Hz
130.07 Hz
$0823
60.04 Hz
59.98 Hz
$03C1
130.21 Hz
129.94 Hz
$0824
60.01 Hz
59.95 Hz
$03C2
130.07 Hz
129.80 Hz
$0825
59.98 Hz
59.92 Hz
$04E2
100.08 Hz
99.92 Hz
$09C4
50.02 Hz
49.98 Hz
$04E3
100.00 Hz
99.84 Hz
$09C5
50.00 Hz
49.96 Hz
$04E4
99.92 Hz
99.76 Hz
$09C6
49.98 Hz
49.94 Hz
$06F9
70.07 Hz
69.99 Hz
$1FFD
15.266 Hz
15.262 Hz
$06FA
70.03 Hz
69.95 Hz
$1FFE
15.264 Hz
15.260 Hz
$06FB
69.99 Hz
69.91 Hz
$1FFF
15.262 Hz
15.258 Hz
VOF — Vertical Frequency Counter Overflow
This read-only bit is set when an overflow has occurred on the 13-bit
vertical frequency counter. Reset clears this bit, and will be updated
every vertical frame.
An overflow occurs when the period of Vsync frame exceeds
64.768ms (a vertical frame frequency lower than 15.258Hz).
1 = A vertical frequency counter overflow has occurred
0 = No vertical frequency counter overflow has occurred
Data Sheet
264
MC68HC908LD64 — Rev. 3.0
Sync Processor
Freescale Semiconductor
Sync Processor
Sync Processor I/O Registers
CPW[1:0] — Clamp Pulse Width
The CPW1 and CPW0 bits are used to select the output clamp pulse
width. Reset clears these bits, selecting a default clamp pulse width
between 0.33µs and 0.375µs. These bits always read as Zeros.
Table 17-6. Clamp Pulse Width
CPW1
CPW0
Clamp Pulse Width
0
0
0.33µs to 0.375µs
0
1
0.5µs to 0.542µs
1
0
0.75µs to 0.792µs
1
1
2µs to 2.042µs
17.6.4 Hsync Frequency Registers (HFRs)
This register pair contains the 13-bit Hsync frequency count value and
an overflow bit.
Address:
Read:
$0043
Bit 7
6
5
4
3
2
1
Bit 0
HFH7
HFH6
HFH5
HFH4
HFH3
HFH2
HFH1
HFH0
0
0
0
0
0
0
0
0
Write:
Reset:
Figure 17-8. Hsync Frequency High Register
Address:
Read:
$0044
Bit 7
6
5
4
3
2
1
Bit 0
HOVER
0
0
HFL4
HFL3
HFL2
HFL1
HFL0
0
0
0
0
0
0
0
0
Write:
Reset:
= Unimplemented
Figure 17-9. Hsync Frequency Low Register
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Sync Processor
265
Sync Processor
HFH[7:0], HFL[4:0] — Horizontal Line Frequency
This read-only 13-bit contains the number of horizontal lines in a
32ms window. An internal 13-bit counter counts the Hsync pulses
within a 32ms window in every 32.768ms period. If the FSHF bit in
SPCR1 is set, only the most 11-bits (HFH[7:0] & HFL[4:2]) will be
updated by the counter. Thus, providing a Hsync pulse count in a 8ms
window in every 8.192ms.
The most significant 8 bits of counted value is transferred to the high
byte register, and the least significant 5 bits is transferred to an
intermediate buffer. When the high byte register is read, the 5-bit
counted value stored in the intermediate buffer will be uploaded to the
low byte register. Therefore, user the program must read the high byte
register first then low byte register in order to get the complete
counted value of Hsync pulses. If the counter overflows, the overflow
flag, HOVER, will be set, indicating the number of Hsync pulses in
32ms are more than 8191 (213 –1), i.e. a Hsync frequency greater
than 256kHz.
For the 32ms window, the HFHR and HFLR are such that the
frequency step unit in the 5-bit of HFLR is 0.03125kHz, and the step
unit in the 8-bit HFHR is 1kHz. Therefore, the Hsync frequency can
be easily calculated by:
Hsync Frequency = [HFH + (HFL × 0.03125)] kHz
where: HFH is the value of HFH[7:0]
HFL is the value of HFL[4:0]
HOVER — Hsync Frequency Counter Overflow
This read-only bit is set when an overflow has occurred on the 13-bit
Hsync frequency counter. Reset clears this bit, and will be updated
every count period.
An overflow occurs when the number Hsync pulses exceed 8191, a
Hsync frequency greater than 256kHz.
1 = A Hsync frequency counter overflow has occurred
0 = No Hsync frequency counter overflow has occurred
Data Sheet
266
MC68HC908LD64 — Rev. 3.0
Sync Processor
Freescale Semiconductor
Sync Processor
Sync Processor I/O Registers
17.6.5 Sync Processor Control Register 1 (SPCR1)
Address:
$0046
Bit 7
Read:
6
4
3
2
1
Bit 0
HPS1
HPS0
R
R
ATPOL
FSHF
0
0
0
0
LVSIF
LVSIE
Write:
Reset:
5
0
0
0
= Unimplemented
R
= Reserved
Figure 17-10. Sync Processor Control Register 1 (SPCR1)
LVSIE — Low VSync Interrupt Enable
When this bit is set, the LVSIF flag is enabled to generate an interrupt
request to the CPU. When LVSIE is cleared, the LVSIF flag is
prevented from generating an interrupt request to the CPU. Reset
clears this bit.
1 = Low Vsync interrupt enabled
0 = Low Vsync interrupt disabled
LVSIF — Low VSync Interrupt Flag
This read-only bit is set when the value of VFR is higher than $C00
(vertical frame frequency below 40.7Hz). LVSIF generates an
interrupt request to the CPU if the LVSIE is also set. This bit is cleared
by writing a "0" to it or reset.
1 = Vertical frequency is below 40.7Hz
0 = Vertical frequency is higher than 40.7Hz
HPS[1:0] — HSYNC input Detection Pulse Width
These two bits control the detection pulse width of HSYNC input.
Reset clears these two bits, setting a default middle frequency of
HSYNC input.
Table 17-7. HSYNC Polarity Detection Pulse Width
HPS1
HPS0
Polarity Detection Pulse Width
0
0
Long > 7µs and Short < 6µs
1
X
Long > 3.5µs and Short < 3µs
0
1
Long > 14µs and Short < 12µs
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Sync Processor
267
Sync Processor
ATPOL — Auto Polarity
This bit, together with the VINVO or HINVO bits in SPCSR controls
the output polarity of the VOUT or HOUT signals respectively. Reset
clears this bit (see Table 17-8).
Table 17-8. ATPOL, VINVO, and HINVO setting
Sync Outputs:
VOUT/HOUT
ATPOL
VINVO / HINVO
0
0
Same polarity as sync input
0
1
Inverted polarity of sync input
1
0
Negative polarity sync output
1
1
Positive polarity sync output
FSHF — Fast Horizontal Frequency Count
This bit is set to shorten the measurement cycle of the horizontal
frequency. If it is set, only HFH[7:0] and HFL[4:2] will be updated by
the Hsync counter, providing a count in a 8ms window in every
8.192ms, with HFL[1:0] reading as zeros. Therefore, user can
determine the horizontal frequency change within 8.192ms to protect
critical circuitry. Reset clears this bit.
1 = Number of Hsync pulses is counted in an 8ms window
0 = Number of Hsync pulses is counted in a 32ms window
17.6.6 H & V Sync Output Control Register (HVOCR)
Address:
$003F
Bit 7
6
5
4
3
2
1
Bit 0
Read:
DCLKPH1 DCLKPH0
R
HVOCR1 HVOCR0
Write:
Reset:
0
= Unimplemented
0
R
0
0
= Reserved
Figure 17-11. H&V Sync Output Control Register (HVOCR)
Data Sheet
268
MC68HC908LD64 — Rev. 3.0
Sync Processor
Freescale Semiconductor
Sync Processor
System Operation
DCLKPH[1:0] — DCLK Output Phase Adjustment
These two bits are programmed to adjust the DCLK output phase.
Each increment adds approximately 2 to 3ns delay to the DCLK
output.
HVOCR[1:0] — Free Running Video Mode Select Bits
These two bits together with MUL[7:4] and VRS[7:4] in CGM’s PLL
programming register determine the frequencies of the internal
generated free-running signals for output to HOUT, VOUT, DE, and
DCLK pins, when the SOUT bit is set in the sync processor I/O control
register. These two bits determine the prescaler of PLL reference
clock in the CGM module. When HVOCR[1:0]=11, the prescaler is 2;
for other values, the prescaler is 3. Reset clears these bits, setting a
default horizontal frequency of 31.25kHz and a vertical frequency of
60Hz, a video mode of 640×480. (See Section 8. Clock Generator
Module (CGM).)
Table 17-9. Free-Running HSOUT, VSOUT, DE, and DCLK Settings
HVOCR[1:0]
MUL[7:4]
VRS[7:4]
HOUT
Frequency
VOUT
Frequency
DCLK
Frequency
DE Video Mode
00
3
3
31.45kHz
59.91Hz
24MHz
VGA 640 × 480
01
5
3
37.87kHz
60.31Hz
40MHz
SVGA 800 × 600
10
8
6
48.37kHz
60.31Hz
64MHz
XGA 1024 × 768
11
9
9
64.32kHz
60.00Hz
108MHz
SXGA 1280 × 1024
17.7 System Operation
This Sync Processor is designed to assist in determining the video mode
of incoming HSYNC and VSYNC of various frequencies and polarities,
and DPMS modes. In the DPMS standard, a no sync pulses definition
can be detected when the value of the Hsync Frequency Register (the
number of Hsync pulses) is less than one or when the VOF bit is set.
Since the Hsync Frequency Register is updated repeatedly in every
32.768ms, and a valid Vsync must have a frequency greater than
40.7Hz, a valid Vsync pulse will arrive within the 32.768ms window.
Therefore, the user should read the Hsync Frequency Register every
32.768ms to determine the presence of Hsync and/or Vsync pulses.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Sync Processor
269
Sync Processor
Data Sheet
270
MC68HC908LD64 — Rev. 3.0
Sync Processor
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 18. On-Screen Display (OSD)
18.1 Contents
18.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
18.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
18.4
System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273
18.5
OSD FLASH Font Memory Map . . . . . . . . . . . . . . . . . . . . . . . 275
18.6
OSD Screen Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
18.7 OSD Module I/O Registers . . . . . . . . . . . . . . . . . . . . . . . . . . .277
18.7.1 OSD Control Register (OSDCR) . . . . . . . . . . . . . . . . . . . . 277
18.7.2 OSD Status Register (OSDSR) . . . . . . . . . . . . . . . . . . . . . 278
18.7.3 OSD Data Registers (OSDDRH:OSDDRL) . . . . . . . . . . . . 279
18.7.4 OSD Row Address Register (OSDRAR) . . . . . . . . . . . . . . 280
18.7.5 OSD Column Address Register (OSDCAR). . . . . . . . . . . . 280
18.7.6 OSD FLASH Even High Byte Write Buffer (OSDEHBUF) . 281
18.8 OSD Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
18.8.1 OSD Display Registers (Attribute and Code Registers) . . . 282
18.8.2 Row Attribute Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
18.8.3 Control, Window, and Pattern Registers . . . . . . . . . . . . . . 283
18.8.3.1
Window Registers 1, 2, 3, 4 . . . . . . . . . . . . . . . . . . . . . . 284
18.8.3.2
Vertical Delay Control Register . . . . . . . . . . . . . . . . . . . 285
18.8.3.3
Horizontal Delay Control Register . . . . . . . . . . . . . . . . . 286
18.8.3.4
Character Height Control Register . . . . . . . . . . . . . . . . . 286
18.8.3.5
Frame Control Registers . . . . . . . . . . . . . . . . . . . . . . . . 288
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
On-Screen Display (OSD)
271
On-Screen Display (OSD)
18.2 Introduction
This section describes the on-screen display (OSD) module. This
module includes a 15 row × 30 column display window and video pattern
generator.
18.3 Features
Features of the on-screen display module include:
•
Up to 384 fonts: 12 × 16 or 16 × 16
•
Resolution: up to 2048 dots/line
•
Scan lines per frame: up to 2048 lines
•
Fully programmable display character array of
15 rows by 30 columns
•
Eight selections of color for menu windows and fonts
•
Row to row spacing control
•
Four programmable background windows
•
Window shadowing with programmable width, height, and color
•
Programmable vertical and horizontal positioning for display
center
•
Full screen pattern output of free-running VGA, SVGA, XGA,
SXGA timing from Sync Processor module
•
Double character height and double character width
Data Sheet
272
MC68HC908LD64 — Rev. 3.0
On-Screen Display (OSD)
Freescale Semiconductor
On-Screen Display (OSD)
System Overview
Addr.
Register Name
$0060
Read:
OSDMEN
OSD Control Register
Write:
(OSDCR)
Reset:
0
$0061
$0062
$0063
$0064
$0065
$0066
Bit 7
Read:
OSD Status Register
Write:
(OSDSR)
Reset:
6
5
4
3
R
OSDRST
CLKINV
CLKPH1
0
0
0
2
1
Bit 0
CLKPH0 HALFCLK OSDIEN
0
0
0
DENDIF
WRDY
0
1
0
Read:
OSDD7
OSD Data Register Low
Write:
(OSDDRL)
Reset:
OSDD6
OSDD5
OSDD4
OSDD2
OSDD1
OSDD0
OSDD10
OSDD9
OSDD8
ROWA3
ROWA2
ROWA1
ROWA0
0
0
0
0
COLA4
COLA3
COLA2
COLA1
COLA0
0
0
0
0
0
DOT12
DOT11
DOT10
DOT9
DOT8
Unaffected by reset
Read:
OSDD15
OSD Data Register High
Write:
(OSDDRH)
Reset:
OSDD14
OSDD13
OSDD12
OSDD11
Unaffected by reset
Read:
OSD Row Address
Register Write:
(OSDRAR)
Reset:
Read:
OSD Column Address
Register Write:
(OSDCAR)
Reset:
Read:
OSD FLASH Even
DOT15
High Byte Write Buffer Write:
(OSDEHBUF)
Reset:
OSDD3
DOT14
DOT13
Unaffected by reset
= Unimplemented
R
= Reserved
Figure 18-1. On-Screen Display I/O Register Summary
18.4 System Overview
The OSD module has a full screen memory architecture. Refresh is done
by the built-in synchronous circuitry. The full screen display data can be
updated through writing row, column, and data buffers. Thus, the display
data can be updated randomly afterward.
Figure 18-2 shows the block diagram of the OSD module.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
On-Screen Display (OSD)
273
On-Screen Display (OSD)
INTERNAL BUS
$0060 Bit7
OSDMEN
ROW AND COLUMN
$0064
$0065
ADDRESS AND DATA
BUFFERS
PHSYNC
PVSYNC
PCLK
CONTROL
LOGIC
Row and
Column
ROW AND COLUMN Address 16 ROW × 32 COLUMN Code
16 × 16
ADDRESS
ATTRIBUTE AND CODE
384 FONTS
GENERATOR
DISPLAY RAM
FLASH MEMORY
CLOCK
GENERATOR
SHIFT REGISTER
$0062
$0063
OSDR
ROW ATTRIBUTE
LATCHES
OUTPUT
OSDG
LOGIC
FRAME ATTRIBUTE
PATTERN GENERATOR
CONTROL
OSDB
FBKG
Figure 18-2. OSD Block Diagram
User program must write the row and column addresses to the row and
column address registers, then write the code and attributes to the 16-bit
OSD data register to complete one display character or symbol update.
The WRDY bit will then be set to acknowledge that the data has been
updated to the addressed display RAM. This process is repeated for
other updates.
Data Sheet
274
MC68HC908LD64 — Rev. 3.0
On-Screen Display (OSD)
Freescale Semiconductor
On-Screen Display (OSD)
OSD FLASH Font Memory Map
18.5 OSD FLASH Font Memory Map
The 12K-byte FLASH memory from $1000 to $3FFF is for OSD font
storage. This OSD font memory stores up to 384 fonts, with each font
made up of 16 lines by 16 bits, i.e. 32 memory locations. The OSD fonts
memory can be accessed by CPU when the OSDMEN bit in the OSD
control register is clear. See 18.7.6 OSD FLASH Even High Byte Write
Buffer (OSDEHBUF) for how to program the OSD font memory.
Odd Byte
$0001
$1000 – $1001
$1002 – $1003
$1004 – $1005
$1006 – $1007
$1008 – $1009
$100A – $100B
$100C – $100D
$100E – $100F
$1010 – $1011
$1012 – $1013
$1014 – $1015
$1016 – $1017
$1018 – $1019
$101A – $101B
$101C – $101D
$101E – $101F
$1020 – $1021
$1022 – $1023
$1024 – $1025
$1026 – $1027
$1028 – $1029
$102A – $102B
$102C – $102D
$102E – $102F
$1030 – $1031
$1032 – $1033
$1034 – $1035
$1036 – $1037
$1038 – $1039
$103A – $103B
$103C – $103D
$103E – $103F
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
$3FE0 – $3FE1
$3FE2 – $3FE3
$3FE4 – $3FE5
$3FE6 – $3FE7
$3FE8 – $3FE9
$3FEA – $3FEB
$3FEC – $3FED
$3FEE – $3FEF
$3FF0 – $3FF1
$3FF2 – $3FF3
$3FF4 – $3FF5
$3FF6 – $3FF7
$3FF8 – $3FF9
$3FFA – $3FFB
$3FFC – $3FFD
$3FFE – $3FFF
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Dot
16 lines
$0000
16 lines
Even Byte
Font Memory
Address
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Character
Code
$0002
$017F
Figure 18-3. Memory Map of OSD FLASH Fonts
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
On-Screen Display (OSD)
275
On-Screen Display (OSD)
18.6 OSD Screen Memory Map
The OSD operating screen is mapped to a 1K-byte RAM array from
$0800 to $0BFF. The array is organized as 16 rows by 32 columns, with
two bytes (16-bit) for each row-column location. Figure 18-4 shows the
OSD screen memory map.
28
29
30
DISPLAY
REGISTERS
A = Character ATTRIBUTE
$83D
$83C
ROW ATTRIBUTE REGISTERS
$83B
$83A
$839
$838
$807
$806
A C A C A C
A C A C
A C A C A C
A C A C
A C A C A C
A C A C
A C A C A C
A C A C
A C A C A C
A C A C
A C A C A C
A C A C
A C A C A C
A C A C
A C A C A C
A C A C
A C A C A C
A C A C
A C A C A C
A C A C
A C A C A C
A C A C
A C A C A C
A C A C
A C A C A C
A C A C
A C A C A C
A C A C
A C A C A C
A C A C
CONTROL, WINDOW, AND PATTERN REGISTERS
$805
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
$804
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
$803
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
31
$83F
3
$802
2
$801
$840 – $87F
$880 – $8BF
$8C0 – $8FF
$900 – $93F
$940 – $97F
$980 – $9BF
$9C0 – $9FF
$A00 – $A3F
$A40 – $A7F
$A80 – $ABF
$AC0 – $AFF
$B00 – $B3F
$B40 – $B7F
$B80 – $BBF
NOT MAPPED
1
$800
DISPLAY RAM
ADDRESS
0
ROW
$83E
COLUMN
C = Character CODE
Figure 18-4. Memory Map of OSD Registers
The area covering row0-column0 and row14-column29 are called the
active display registers. Each 16-bit display register defines the
character to be displayed, with an character code (character from font
memory) and an attribute code for that character. Column30 of each row
is the attribute register for the entire row. Row15 registers (not memory
mapped) are used for control, window, and pattern for the entire OSD
screen. See 18.8 OSD Registers for register definitions.
The CPU have direct access to the all screen memory registers ($0800
to $0BFF) when the OSDMEN bit in the OSD control register is clear.
When the OSD circuitry is displaying the characters (OSDMEN=1),
updates to display is by indirectly writing to these registers. The OSD
data registers, row register, column register are used for this purpose.
See 18.7.3 OSD Data Registers (OSDDRH:OSDDRL), 18.7.4 OSD
Row Address Register (OSDRAR), and 18.7.5 OSD Column Address
Register (OSDCAR).
Data Sheet
276
MC68HC908LD64 — Rev. 3.0
On-Screen Display (OSD)
Freescale Semiconductor
On-Screen Display (OSD)
OSD Module I/O Registers
18.7 OSD Module I/O Registers
Seven registers are associated with the OSD module, they outlined in
the following sections.
18.7.1 OSD Control Register (OSDCR)
Address:
$0060
Bit 7
6
5
4
3
OSDMEN
R
OSDRST
CLKINV
CLKPH1
0
0
0
2
1
0
Read:
CLKPH0 HALFCLK OSDIEN
Write:
Reset:
0
0
0
0
Figure 18-5. OSD Control Register (OSDCR)
OSDMEN — OSD Memory Enable
When this bit is clear, the OSD RAM and font FLASH memory is
directly under CPU access. When OSDMEN is set, OSD circuitry has
read control over the OSD RAM and font FLASH memory for
displaying the contents; CPU access is indirect, by writing to address
and data buffers. The OSDMEN bit should be cleared while no OSD
are displaying. Reset clear this bit.
1 = OSD RAM and font FLASH is under OSD circuitry access
0 = OSD RAM and font FLASH is directly under CPU access
OSDRST — OSD Module Reset
Setting this bit resets the entire OSD logic and row15 registers (row1
to row14 registers are unaffected), and holds the OSD in the reset
state. The input PCLK clock is prevented from entering the OSD
module to reduce power consumption.
Reset clear this bit.
1 = Reset OSD logic and row15 registers
0 = No effect
CLKINV — Pixel Clock Inversion
This bit is set to invert the PCLK input of OSD. Reset clears this bit.
1 = PCLK input inverted
0 = PCLK input not inverted
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
On-Screen Display (OSD)
277
On-Screen Display (OSD)
CLKPH[1:0] — Pixel Clock Phase Adjustment
These two bits adjust the pixel clock phase to the OSD module. Thus
the OSDR, OSDG, and OSDB outputs can be in phase with video
signals. Reset clears all these bits.
HALFCLK — Half Frequency of Pixel Clock
This bit is set to divide the incoming pixel clock by two as the OSD
display clock. Reset clears this bit.
1 = OSD module display clock is PCLK divided-by-2
0 = OSD module display clock is PCLK divided-by-1
OSDIEN — OSD Interrupt Enable
This bit enable OSD interrupt when DENDIF in the OSD status
register is set. Reset clear this bit.
1 = DENDIF bit set will generate interrupt request to CPU
0 = DENDIF bit set will not generate interrupt request to CPU
18.7.2 OSD Status Register (OSDSR)
Address:
$0061
Bit 7
Read:
6
5
4
3
2
WRDY
0
DENDIF
Write:
Reset:
1
0
1
0
= Unimplemented
Figure 18-6. OSD Status Register (OSDSR)
WRDY — OSD Buffer Write Ready
This bit is set when the OSD data registers, $0062 and $0063, are
ready to be loaded with new data. The WRDY is cleared after the CPU
writes to the low byte register, $0062. It becomes set again when the
OSD circuitry has transferred the content of data registers to the
display RAM. Reset sets this bit.
1 = OSD data buffers ready for new data
0 = OSD data buffers busy
Data Sheet
278
MC68HC908LD64 — Rev. 3.0
On-Screen Display (OSD)
Freescale Semiconductor
On-Screen Display (OSD)
OSD Module I/O Registers
DENDIF — OSD Display End Interrupt Flag
This bit is set when the OSD has finished the row15 display; it is
cleared by writing a logic 0 to it. The DENDIF bit is designed for user
program to update the OSD RAM while not displaying OSD. Reset
clears this bit.
1 = OSD has finished the row15 display
0 = No effect
18.7.3 OSD Data Registers (OSDDRH:OSDDRL)
Address:
$0063
Bit 7
6
5
4
3
2
1
0
OSDD15
OSDD14
OSDD13
OSDD12
OSDD11
OSDD10
OSDD9
OSDD8
Read:
Write:
Reset:
Unaffected by reset
Figure 18-7. OSD Data Register High (OSDDRH)
Address:
$0062
Bit 7
6
5
4
3
2
1
0
OSDD7
OSDD6
OSDD5
OSDD4
OSDD3
OSDD2
OSDD1
OSDD0
Read:
Write:
Reset:
Unaffected by reset
Figure 18-8. OSD Data Register Low (OSDDRL)
OSDD[15:0] — OSD RAM 16-Bit Data Buffer
While OSD circuitry is displaying data from the display RAM, update
the display RAM (location specified by the row and column address
registers, OSDRAR and OSDCAR) by writing data to the high byte
register (OSDDRH) followed by the low byte register (OSDDRL). After
writing to the OSDDRL, the OSD buffer write ready bit (WRDY) will be
cleared. WRDY becomes set again when the OSD circuitry has
transferred the content of the OSD data registers to the display RAM.
Reset has no effect on these bits.
(See 18.6 OSD Screen Memory Map.)
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
On-Screen Display (OSD)
279
On-Screen Display (OSD)
18.7.4 OSD Row Address Register (OSDRAR)
Address:
$0064
Bit 7
6
5
4
3
2
1
0
ROWA3
ROWA2
ROWA1
ROWA0
0
0
0
0
Read:
Write:
Reset:
Figure 18-9. OSD Row Address Register (OSDRAR)
ROWA[3:0] — OSD RAM Row Address
These bits define the row address of the OSD RAM. Together with the
column address, the row-column address defines the location in the
OSD screen memory where data is to be transferred from the data
buffers (OSD data registers). Data is transferred when the high byte
data register is written ($0063). Reset clears these bits to zero.
(See 18.6 OSD Screen Memory Map.)
18.7.5 OSD Column Address Register (OSDCAR)
Address:
$0065
Bit 7
6
5
4
3
2
1
0
COLA4
COLA3
COLA2
COLA1
COLA0
0
0
0
0
0
Read:
Write:
Reset:
Figure 18-10. OSD Column Address Register (OSDCAR)
COLA[4:0] — OSD RAM Column Address
These bits define the column address of the OSD RAM. Together with
the row address, the row-column address defines the location in the
OSD screen memory where data is to be transferred from the data
buffers (OSD data registers). Data is transferred when the high byte
data register is written ($0063). Reset clears these bits to zero.
(See 18.6 OSD Screen Memory Map.)
Data Sheet
280
MC68HC908LD64 — Rev. 3.0
On-Screen Display (OSD)
Freescale Semiconductor
On-Screen Display (OSD)
OSD Module I/O Registers
18.7.6 OSD FLASH Even High Byte Write Buffer (OSDEHBUF)
Address:
$0066
Bit 7
6
5
4
3
2
1
0
DOT15
DOT14
DOT13
DOT12
DOT11
DOT10
DOT9
DOT8
Read:
Write:
Reset:
Unaffected by reset
Figure 18-11. OSD FLASH Even High Byte Write Buffer (OSDEHBUF)
DOT[15:8] — OSD FLASH Even High Byte Buffer
These bits define the even byte for a single line of OSD font, to be
programmed to the OSD FLASH memory. Reset has no effect on
these bits. Figure 18-12 shows an example of an OSD font.
OSDEHBUF
DOT15 DOT14 DOT13 DOT12 DOT11 DOT10 DOT9
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Odd Byte
$1000 – $1001
$1002 – $1003
$1004 – $1005
$1006 – $1007
$1008 – $1009
$100A – $100B
$100C – $100D
$100E – $100F
$1010 – $1011
$1012 – $1013
$1014 – $1015
$1016 – $1017
$1018 – $1019
$101A – $101B
$101C – $101D
$101E – $101F
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Dot
16 lines
Even Byte
Font Memory
Address
DOT8
Figure 18-12. OSD Font Even Byte Buffer
The OSDEHBUF register is a buffer for temporarily storing the even byte
(or high byte) of an OSD font line to be programmed to the OSD FLASH
memory. A 16-bit OSD font line is programmed by writing the even byte
to OSDEHBUF, followed by a FLASH programming routine to the odd
byte in the font memory. Programming the odd byte will automatic
program the even byte. See 18.5 OSD FLASH Font Memory Map for
OSD font memory map and Section 4. FLASH Memory on FLASH
programming.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
On-Screen Display (OSD)
281
On-Screen Display (OSD)
18.8 OSD Registers
The following sections define the OSD registers for display control as
illustrated in Figure 18-4 . Memory Map of OSD Registers.
18.8.1 OSD Display Registers (Attribute and Code Registers)
The OSD active display registers consist of 450 attribute and code
registers in a 15 row by 30 column matrix. These registers are memory
mapped to RAM locations as illustrated in Figure 18-4.
When OSDMEN=0 (not displaying), CPU has direct access to these
registers by reading/writing the RAM locations. When OSDMEN=1
(displaying), CPU access these registers indirectly by writing to the OSD
data registers, row register and column register.
Each attribute and code register affects one display character.
Row 0–14, Column 0–29:
15
14
13
BGR BGG BGB
12
11
10
9
FSS
R
G
B
8
CHARACTER ATTRIBUTE
7
6
5
4
3
2
1
0
CRADDR
CHARACTER CODE
CRADDR — Character Address
These bits form an address to select one of the 384
characters/symbols available from the FLASH font memory.
BGR, BGG, BGB — Character Background Color
These bits define the color of the background of the associated
character/symbol. When all three bits are clear, no background will be
shown. Therefore, seven background colors can be selected.
FSS — Font Size
This bit will determine the font size of the associated
character/symbol. Reset clears this bit.
1 = The font size is 12 × 16 (DOT13 to DOT2)
0 = The font size is 16 × 16
R, G, B — Character Color
These bits define the color of the associated character/symbol.
Data Sheet
282
MC68HC908LD64 — Rev. 3.0
On-Screen Display (OSD)
Freescale Semiconductor
On-Screen Display (OSD)
OSD Registers
18.8.2 Row Attribute Registers
The 15 row attribute registers are at column 30 of the display rows.
These registers are memory mapped to RAM locations as illustrated in
Figure 18-4.
When OSDMEN=0 (not displaying), CPU has direct access to these
registers by reading/writing the RAM locations. When OSDMEN=1
(displaying), CPU access these registers indirectly by writing to the OSD
data registers, row register and column register.
Each row attribute register affects characters of a display row.
Row 0–14, Column 30:
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
REN CHS CWS
REN — Row Enable
Set this bit to enable OSD circuitry to display the current row of
characters. This bit should be cleared when display RAM is accessed
directly by the CPU and when the row points to a font that is to be
updated in the FLASH font memory.
1 = Enable display for this row
0 = Disable display for this row
CHS — Character Height
Set this bit to display double height characters for this row.
1 = Display characters as double height for this row
0 = Display characters as normal height for this row
CWS — Character Width
Set this bit to display double width characters for this row.
1 = Display characters as double width for this row
0 = Display characters as normal width for this row
18.8.3 Control, Window, and Pattern Registers
Row-15 registers are for window, pattern, and miscellaneous control of
the entire OSD screen. These registers are NOT memory mapped to
RAM locations. CPU access these registers by writing to the OSD data
registers, row register and column register.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
On-Screen Display (OSD)
283
On-Screen Display (OSD)
18.8.3.1 Window Registers 1, 2, 3, 4
Four background windows are available, with each window controlled by
a set of three registers in row 15.
Window 1 has the highest priority, and window 4 the least. If window
over-lapping occurs, the higher priority window will cover the lower one,
and the higher priority color will take over on the overlapped window
area.
If the row/column start address is greater than the end address, that
window will not be displayed.
COLUMN
0
1
2
3
4
5
6
7
8
9
10
11
ROW 15
Window 1 Registers
Window 2 Registers
Window 3 Registers
Window 4 Registers
Row 15, Column 0, 3, 6, 9:
15
14
13
12
11
10
9
8
7
6
5
4
3
ROW START ADDRESS
MSB
2
1
0
ROW END ADDRESS
LSB
MSB
4
3
LSB
Row 15, Column 1, 4, 7, 10:
15
14
13
12
11
10
9
8
7
6
5
COLUMN START ADDRESS
MSB
LSB
2
1
WEN
0
W_SHD
Row 15, Column 2, 5, 6, 11:
15
14
13
12
11
10
9
8
7
6
5
4
3
COLUMN END ADDRESS
MSB
LSB
2
1
0
R
G
B
WEN — Background Window Enable
Set this bit to enable background window generation
1 = Enable background window
0 = Disable background window
Data Sheet
284
MC68HC908LD64 — Rev. 3.0
On-Screen Display (OSD)
Freescale Semiconductor
On-Screen Display (OSD)
OSD Registers
W_SHD — Shadow on Window
Set this bit to activate the window shadowing. When the window is
active, the right M pixels and lower N horizontal scan lines will output
shadowing. The M, N, and color of window shadow is defined in the
frame control registers located at row 15, column 16, 17, 18, and 19.
See 18.8.3.5 Frame Control Registers for details.
1 = Background window shadow enabled
0 = Background window shadow disabled
Column start address
Column end address
WINDOW AREA
Row start address
N
M and N are defined in the
frame control registers located
at row 15, column 16 and 17.
Row end address
N
SHADOW
M
M
R, G, B — Background Window Color
These bits define the color of the background window.
18.8.3.2 Vertical Delay Control Register
Row 15, Column 12:
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
VERTD
MSB
LSB
VERTD —þVertical Delay
These bits define the vertical starting position. The 8-bit gives 256
steps, with each step increment of four horizontal lines for each field.
Its value cannot be zero at anytime. In order to avoid screen
misalignment, the value of VERTD is decided by the last OSD line not
over the next leading edge of PVSYNC.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
On-Screen Display (OSD)
285
On-Screen Display (OSD)
18.8.3.3 Horizontal Delay Control Register
Row 15, Column 13:
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
HORD
MSB
LSB
HORD — Horizontal Delay
These bits define the horizontal starting position for character display.
The 8-bit gives 256 steps, with each step increment of six dots shift to
the right on the monitor screen. The maximum value of HORD is
decided by the rightmost character not exceeding the next leading
edge of PHSYNC.
18.8.3.4 Character Height Control Register
This register controls the height of all displayed characters.
Row 15, Column 14:
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
CH5
CH4
CH3
CH2
CH1
CH0
CH[3:0] — Expand Characters by BRM Algorithm
These bits expand the 16-line characters using the binary rate
multiplier (BRM) algorithm. See Figure 18-13 for some examples.
CH[5:4] — Display Character Height Select
These two bits define the final height for the display characters. See
Figure 18-14 for illustration.
CH5:CH4
Character Display Size
00 or 01
Display size is same size as expanded font by CH[3:0].
The default value is 00.
10
Display size is double size of expanded font by CH[3:0].
11
Display size is triple size of expanded font by CH[3:0].
Data Sheet
286
MC68HC908LD64 — Rev. 3.0
On-Screen Display (OSD)
Freescale Semiconductor
On-Screen Display (OSD)
OSD Registers
NOTE:
To avoid undesirable on-screen displays, such as jittering and
characters wrapping to the top, care should be taken when implementing
character height expansion and vertical starting position — ensure the
last line of row14 does not exceed the PVSYNC pulse of the next frame.
Characters Height Expanded by 4-bit BRM
Character in Font Memory
12 × 16 matrix
CH[3:0] = $0
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16 Lines
CH[3:0] = $6
22 Lines
CH[3:0] = $9
25 Lines
CH[3:0] = $F
31 Lines
Figure 18-13. Character Font Matrix Height Expansion by CH[3:0]
3x
48 to 93 lines
2x
32 to 62 lines
1x
16 to 31 lines
CH[5:4] = 0:0 or 0:1
CH[5:4] = 1:0
CH[5:4] = 1:1
Figure 18-14. Display Character Height
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
On-Screen Display (OSD)
287
On-Screen Display (OSD)
18.8.3.5 Frame Control Registers
Row 15, Column 15:
15
14
13
12
11
10
9
8
7
OSD_EN
6
5
4
3
2
1
0
VPOL HPOL
OSD_EN — OSD Enable
Set this bit to enable the OSD module output pins, OSDR, OSDG,
OSDB, and FBKG. When OSD_EN is clear, all OSD output pins are
high impedance. This bit is cleared after a POR, reset, or when
OSDRST bit (bit-5 in OSD control register) is set.
1 = OSD output pins: OSDR, OSDG, OSDB, FBKG enabled
0 = OSD output pins held at high impedance
HPOL — Horizontal Sync Polarity
This bit selects the polarity of the incoming horizontal sync signal on
PHSYNC pin. If sync signal is negative polarity, clear this bit. If sync
signal is positive polarity, set this bit. This bit is cleared after a POR,
reset, or when OSDRST bit is set.
1 = Set for positive horizontal sync signal
0 = Clear for negative horizontal sync
VPOL — Vertical Sync Polarity
This bit selects the polarity of the incoming vertical sync signal on
PVSYNC pin. If sync signal is negative polarity, clear this bit. If sync
signal is positive polarity, set this bit. This bit is cleared after a POR,
reset, or when OSDRST bit is set.
1 = Set for positive vertical sync signal
0 = Clear for negative vertical sync
Data Sheet
288
MC68HC908LD64 — Rev. 3.0
On-Screen Display (OSD)
Freescale Semiconductor
On-Screen Display (OSD)
OSD Registers
Row 15, Column 16 and 17 registers control the width and height of the
shadow windows.
WINDOW AREA
N
N
SHADOW
M
M
Row 15, Column 16:
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
WW41 WW40 WW31 WW30 WW21 WW20 WW11 WW10
WWx1, WWx0 — Shadow Window Width Control Bits
These bits selects the width, M, for the respective enabled shadow
window; where x is the window number.
Table 18-1. Shadow Width Setting
WWx1:WWx0
Shadow Width M
(unit in Pixels)
00
2
01
4
10
6
11
8
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
On-Screen Display (OSD)
289
On-Screen Display (OSD)
Row 15, Column 17:
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
WH41 WH40 WH31 WH30 WH21 WH20 WH11 WH10
WHx1, WHx0 — Shadow Window Height Control Bits
These bits selects the width, N, for the respective enabled shadow
window; where x is the window number.
Table 18-2. Shadow Width Setting
WH41:WH40
Shadow Height N
(unit in Lines)
00
2
01
4
10
6
11
8
Row 15, Column 18 and 19 registers control the color of the shadow
windows.
Row 15, Column 18:
15
14
13
12
11
10
9
8
7
6
5
4
R1
G1
B1
6
5
4
R3
G3
B3
3
2
1
0
R2
G2
B2
2
1
0
R4
G4
B4
Row 15, Column 19:
15
14
13
12
11
10
9
8
7
3
Rx, Gx, Bx — Shadow Window Color
These bits define the color of the corresponding shadow window;
where x is the window number
Data Sheet
290
MC68HC908LD64 — Rev. 3.0
On-Screen Display (OSD)
Freescale Semiconductor
On-Screen Display (OSD)
OSD Registers
NOTE:
The width of bottom side shadowing is counted in numbers of columns
and is aligned with the character width (12 dots or 16 dots) of the
following row. Therefore it is possible to have misalignment of this
shadowing while different character formats are used by the last row
inside the window and first row outside the window. The window
shadowing width of row 14 is determined by number of columns of
window times 12 dots.
Row 15, Column 20:
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RSPACE
MSB
LSB
RSPACE — Row Spacing
These bits define the spacing between the display rows, in units of
horizontal scan lines. Due to the non-uniform expansion of the BRM
algorithm used for character height control, this register is normally
used for maintaining a constant OSD menu height for different display
modes, instead of adjusting the character heights. The default value
is 0, i.e. no extra lines inserted between.
Row 15, Column 21:
15
14
13
12
11
10
9
8
7
6
5
4
PGE
3
2
1
0
PGR PGG PGB
PGE — Screen Video Pattern Enable
Set this bit to enable the free-running full-screen video pattern. Reset
clears this bit.
1 = Screen video pattern enabled
0 = Screen video pattern disabled
PGR, PGG, PGB — Screen Video Pattern Color
These bits define the color of the free-running full-screen video
pattern.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
On-Screen Display (OSD)
291
On-Screen Display (OSD)
Data Sheet
292
MC68HC908LD64 — Rev. 3.0
On-Screen Display (OSD)
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 19. Input/Output (I/O) Ports
19.1 Contents
19.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294
19.3 Port A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
19.3.1 Port A Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
19.3.2 Data Direction Register A . . . . . . . . . . . . . . . . . . . . . . . . . 298
19.3.3 Port A Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299
19.4 Port B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
19.4.1 Port B Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
19.4.2 Data Direction Register B . . . . . . . . . . . . . . . . . . . . . . . . . 301
19.4.3 Port B Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302
19.5 Port C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303
19.5.1 Port C Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303
19.5.2 Data Direction Register C . . . . . . . . . . . . . . . . . . . . . . . . . 304
19.5.3 Port C Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305
19.6 Port D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
19.6.1 Port D Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
19.6.2 Data Direction Register D. . . . . . . . . . . . . . . . . . . . . . . . . . 307
19.6.3 Port D Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
19.7 Port E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311
19.7.1 Port E Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311
19.7.2 Data Direction Register E. . . . . . . . . . . . . . . . . . . . . . . . . . 312
19.7.3 Port E Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Input/Output (I/O) Ports
293
Input/Output (I/O) Ports
19.2 Introduction
Thirty-nine (39) bidirectional input-output (I/O) pins form five parallel
ports. All I/O pins are programmable as inputs or outputs.
NOTE:
Addr.
Connect any unused I/O pins to an appropriate logic level, either VDD or
VSS. Although the I/O ports do not require termination for proper
operation, termination reduces excess current consumption and the
possibility of electrostatic damage.
Register Name
Bit 7
6
5
4
3
2
1
Bit 0
PTA7
PTA6
PTA5
PTA4
PTA3
PTA2
PTA1
PTA0
PTB2
PTB1
PTB0
PTC2
PTC1
PTC0
PTD2
PTD1
PTD0
Read:
Port A Data Register
Write:
(PTA)
Reset:
$0000
Unaffected by reset
Read:
Port B Data Register
Write:
(PTB)
Reset:
$0001
Read:
PTB7
PTB5
PTB4
PTB3
Unaffected by reset
0
PTC6
Port C Data Register
Write:
(PTC)
Reset:
$0002
PTB6
PTC5
PTC4
PTC3
Unaffected by reset
Read:
Port D Data Register
Write:
(PTD)
Reset:
$0003
PTD7
PTD6
PTD5
PTD4
PTD3
Unaffected by reset
Read:
$0004
DDRA7
Data Direction Register A
Write:
(DDRA)
Reset:
0
DDRA6
DDRA5
DDRA4
DDRA3
DDRA2
DDRA1
DDRA0
0
0
0
0
0
0
0
DDRB6
DDRB5
DDRB4
DDRB3
DDRB2
DDRB1
DDRB0
0
0
0
0
0
0
0
Read:
$0005
DDRB7
Data Direction Register B
Write:
(DDRB)
Reset:
0
= Unimplemented
Figure 19-1. Port I/O Register Summary
Data Sheet
294
MC68HC908LD64 — Rev. 3.0
Input/Output (I/O) Ports
Freescale Semiconductor
Input/Output (I/O) Ports
Introduction
Addr.
Register Name
Bit 7
Read:
$0006
Data Direction Register C
Write:
(DDRC)
Reset:
6
5
4
3
2
1
Bit 0
DDRC6
DDRC5
DDRC4
DDRC3
DDRC2
DDRC1
DDRC0
0
0
0
0
0
0
0
DDRD6
DDRD5
DDRD4
DDRD3
DDRD2
DDRD1
DDRD0
0
0
0
0
0
0
0
PTE6
PTE5
PTE4
PTE3
PTE2
PTE1
PTE0
0
0
Read:
$0007
DDRD7
Data Direction Register D
Write:
(DDRD)
Reset:
0
Read:
$0008
Port E Data Register
Write:
(PTE)
Reset:
PTE7
Unaffected by reset
Read:
$0009
DDRE7
Data Direction Register E
Write:
(DDRE)
Reset:
0
Read:
Keyboard Interrupt Enable
$004F
Register Write:
(KBIER)
Reset:
DDRE6
DDRE5
DDRE4
DDRE3
DDRE2
DDRE1
DDRE0
0
0
0
0
0
0
0
KBIE7
KBIE6
KBIE5
KBIE4
KBIE3
KBIE2
KBIE1
KBIE0
0
0
0
0
0
0
0
0
Read:
$0068
R
Port-E Control Register
Write:
(PECR)
Reset:
USBDS4E USBDS3E USBDS2E USBDS1E
0
0
0
0
VOUTE
DEE
DCLKE
Read:
$0069
IICDATE
Port-D Control Register
Write:
(PDCR)
Reset:
0
IICSCLE DDCDATE DDCSCLE HOUTE
0
0
0
0
0
0
0
PWM6E
PWM5E
PWM4E
PWM3E
PWM2E
PWM1E
PWM0E
0
0
0
0
0
0
0
Read:
$0078
PWM7E
PWM Control Register
Write:
(PWMCR)
Reset:
0
= Unimplemented
Figure 19-1. Port I/O Register Summary (Continued)
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Input/Output (I/O) Ports
295
Input/Output (I/O) Ports
Table 19-1. Port Control Register Bits Summary
Port
A
B
C
D
E
Bit
DDR
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
DDRA0
DDRA1
DDRA2
DDRA3
DDRA4
DDRA5
DDRA6
DDRA7
DDRB0
DDRB1
DDRB2
DDRB3
DDRB4
DDRB5
DDRB6
DDRB7
DDRC0
DDRC1
DDRC2
DDRC3
DDRC4
DDRC5
DDRC6
DDRD0
DDRD1
DDRD2
DDRD3
DDRD4
DDRD5
DDRD6
DDRD7
DDRE0
DDRE1
DDRE2
DDRE3
DDRE4
DDRE5
DDRE6
DDRE7
Module
KBI
PWM
Module Control
Register
Control Bit
KBIE0
KBIE1
KBIE2
KBIE3
KBIER
$004F
KBIE4
KBIE5
KBIE6
KBIE7
PWM0E
PWM1E
PWM2E
PWM3E
PWMCR
$0078
PWM4E
PWM5E
PWM6E
PWM7E
ADC
ADSCR
$003B
—
—
SYNC
DDC12AB
PDCR
$0069
MMIIC
—
DCLKE
DEE
VOUTE
HOUTE
DDCSCLE
DDCDATE
IICSCLE
IICDATE
USBDS1E
USB
PECR
$0068
USBDS2E
USBDS3E
USBDS4E
Data Sheet
296
ADCH[4:0]
Pin
PTA0/KBI0
PTA1/KBI1
PTA2/KBI2
PTA3/KBI3
PTA4/KBI4
PTA5/KBI5
PTA6/KBI6
PTA7/KBI7
PTB0/PWM0
PTB1/PWM1
PTB2/PWM2
PTB3/PWM3
PTB4/PWM4
PTB5/PWM5
PTB6/PWM6
PTB7/PWM7
PTC0/ADC0
PTC1/ADC1
PTC2/ADC2
PTC3/ADC3
PTC4/ADC4
PTC5/ADC5
PTC6
PTD0/DCLK
PTD1/DE
PTD2/VOUT
PTD3/HOUT
PTD4/DDCSCL
PTD5/DDCSDA
PTD6/IICSCL
PTD7/IICSDA
PTE0/DPLUS1
PTE1/DMINUS1
PTE2/DPLUS2
PTE3/DMINUS2
PTE4/DPLUS3
PTE5/DMINUS3
PTE6/DPLUS4
PTE7/DMINUS4
MC68HC908LD64 — Rev. 3.0
Input/Output (I/O) Ports
Freescale Semiconductor
Input/Output (I/O) Ports
Port A
19.3 Port A
Port A is an 8-bit special-function port that shares all eight of its pins with
the keyboard interrupt module (KBI). (See Section 21. Keyboard
Interrupt Module (KBI).)
19.3.1 Port A Data Register
The port A data register (PTA) contains a data latch for each of the eight
port A pins.
Address:
$0000
Bit 7
6
5
4
3
2
1
Bit 0
PTA7
PTA6
PTA5
PTA4
PTA3
PTA2
PTA1
PTA0
KBI2
KBI1
KBI0
Read:
Write:
Reset:
Alternative Function:
Unaffected by reset
KBI7
KBI6
KBI5
KBI4
KBI3
Figure 19-2. Port A Data Register (PTA)
PTA[7:0] — Port A Data Bits
These read/write bits are software programmable. Data direction of
each port A pin is under the control of the corresponding bit in data
direction register A. Reset has no effect on port A data.
KBI[7:0] — Keyboard Interrupt Pins
The keyboard interrupt enable bits, KBIE[7:0], in the keyboard
interrupt enable register (KBIER), enable the port A pins as external
interrupt pins. (See 19.3.3 Port A Options and Section 21.
Keyboard Interrupt Module (KBI).)
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Input/Output (I/O) Ports
297
Input/Output (I/O) Ports
19.3.2 Data Direction Register A
Data direction register A (DDRA) determines whether each port A pin is
an input or an output. Writing a logic 1 to a DDRA bit enables the output
buffer for the corresponding port A pin; a logic 0 disables the output
buffer.
Address:
$0004
Bit 7
6
5
4
3
2
1
Bit 0
DDRA7
DDRA6
DDRA5
DDRA4
DDRA3
DDRA2
DDRA1
DDRA0
0
0
0
0
0
0
0
0
Read:
Write:
Reset:
Figure 19-3. Data Direction Register A (DDRA)
DDRA[7:0] — Data Direction Register A Bits
These read/write bits control port A data direction. Reset clears
DDRA[7:0], configuring all port A pins as inputs.
1 = Corresponding port A pin configured as output
0 = Corresponding port A pin configured as input
NOTE:
Avoid glitches on port A pins by writing to the port A data register before
changing data direction register A bits from 0 to 1.
Figure 19-4 shows the port A I/O logic.
READ DDRA ($0004)
INTERNAL DATA BUS
WRITE DDRA ($0004)
RESET
DDRAx
WRITE PTA ($0000)
PTAx
PTAx
READ PTA ($0000)
Figure 19-4. Port A I/O Circuit
Data Sheet
298
MC68HC908LD64 — Rev. 3.0
Input/Output (I/O) Ports
Freescale Semiconductor
Input/Output (I/O) Ports
Port A
When bit DDRAx is a logic 1, reading address $0000 reads the PTAx
data latch. When bit DDRAx is a logic 0, reading address $0000 reads
the voltage level on the pin. The data latch can always be written,
regardless of the state of its data direction bit. Table 19-2 summarizes
the operation of the port A pins.
Table 19-2. Port A Pin Functions
Accesses to DDRA
DDRA
Bit
PTA Bit
0
X(1)
1
X
Accesses to PTA
I/O Pin Mode
Read/Write
Read
Write
Input, Hi-Z(2)
DDRA[7:0]
Pin
PTA[7:0](3)
Output
DDRA[7:0]
PTA[7:0]
PTA[7:0]
Notes:
1. X = don’t care.
2. Hi-Z = high impedance.
3. Writing affects data register, but does not affect input.
19.3.3 Port A Options
The keyboard interrupt enable register (KBIER) selects the port A pins
for keyboard interrupt function or as standard I/O function. (See Section
21. Keyboard Interrupt Module (KBI).)
Address:
$004F
Bit 7
6
5
4
3
2
1
Bit 0
KBIE7
KBIE6
KBIE5
KBIE4
KBIE3
KBIE2
KBIE1
KBIE0
0
0
0
0
0
0
0
0
Read:
Write:
Reset:
Figure 19-5. Keyboard Interrupt Enable Register (KIER)
KBIE[7:0] — Keyboard Interrupt Enable Bits
Setting a KBIEx bit to logic 1 configures the PTAx/KBIx pin for
keyboard interrupt function. Reset clears the KBIEx bits.
1 = PTAx/KBIx pin configured as KBIx interrupt pin
0 = PTAx/KBIx pin configured as PTAx standard I/O pin
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Input/Output (I/O) Ports
299
Input/Output (I/O) Ports
19.4 Port B
Port B is an 8-bit special-function port that shares all eight of its pins with
the pulse width modulator (PWM). (See Section 12. Pulse Width
Modulator (PWM).)
19.4.1 Port B Data Register
The port B data register (PTB) contains a data latch for each of the eight
port pins.
Address:
$0001
Bit 7
6
5
4
3
2
1
Bit 0
PTB7
PTB6
PTB5
PTB4
PTB3
PTB2
PTB1
PTB0
PWM2
PWM1
PWM0
Read:
Write:
Reset:
Alternative Function:
Unaffected by reset
PWM7
PWM6
PWM5
PWM4
PWM3
Figure 19-6. Port B Data Register (PTB)
PTB[7:0] — Port B Data Bits
These read/write bits are software-programmable. Data direction of
each port B pin is under the control of the corresponding bit in data
direction register B. Reset has no effect on port B data.
PWM[7:0] — PWM Outputs Pins
The PWM output enable bits PWM7E–PWM0E, in the PWM control
register (PWMCR) enable port B pins as PWM output pins. (See
19.4.3 Port B Options and Section 12. Pulse Width Modulator
(PWM).)
Data Sheet
300
MC68HC908LD64 — Rev. 3.0
Input/Output (I/O) Ports
Freescale Semiconductor
Input/Output (I/O) Ports
Port B
19.4.2 Data Direction Register B
Data direction register B (DDRB) determines whether each port B pin is
an input or an output. Writing a logic 1 to a DDRB bit enables the output
buffer for the corresponding port B pin; a logic 0 disables the output
buffer.
Address:
$0005
Bit 7
6
5
4
3
2
1
Bit 0
DDRB7
DDRB6
DDRB5
DDRB4
DDRB3
DDRB2
DDRB1
DDRB0
0
0
0
0
0
0
0
0
Read:
Write:
Reset:
Figure 19-7. Data Direction Register B (DDRB)
DDRB[7:0] — Data Direction Register B Bits
These read/write bits control port B data direction. Reset clears
DDRB[7:0], configuring all port B pins as inputs.
1 = Corresponding port B pin configured as output
0 = Corresponding port B pin configured as input
NOTE:
Avoid glitches on port B pins by writing to the port B data register before
changing data direction register B bits from 0 to 1.
Figure 19-8 shows the port B I/O logic.
READ DDRB ($0005)
INTERNAL DATA BUS
WRITE DDRB ($0005)
RESET
DDRBx
WRITE PTB ($0001)
PTBx
PTBx
READ PTB ($0001)
Figure 19-8. Port B I/O Circuit
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Input/Output (I/O) Ports
301
Input/Output (I/O) Ports
When bit DDRBx is a logic 1, reading address $0001 reads the PTBx
data latch. When bit DDRBx is a logic 0, reading address $0001 reads
the voltage level on the pin. The data latch can always be written,
regardless of the state of its data direction bit. Table 19-3 summarizes
the operation of the port B pins.
Table 19-3. Port B Pin Functions
Accesses to DDRB
DDRB
Bit
PTB Bit
0
X(1)
1
X
Accesses to PTB
I/O Pin Mode
Read/Write
Read
Write
Input, Hi-Z(2)
DDRB[7:0]
Pin
PTB[7:0](3)
Output
DDRB[7:0]
PTB[7:0]
PTB[7:0]
Notes:
1. X = don’t care.
2. Hi-Z = high impedance.
3. Writing affects data register, but does not affect input.
19.4.3 Port B Options
The PWM control register (PWMCR) selects the port B pins for PWM
function or as standard I/O function. (See Section 12. Pulse Width
Modulator (PWM).)
Address:
$0078
Bit 7
6
5
4
3
2
1
Bit 0
PWM7E
PWM6E
PWM5E
PWM4E
PWM3E
PWM2E
PWM1E
PWM0E
0
0
0
0
0
0
0
0
Read:
Write:
Reset:
Figure 19-9. PWM Control Register (PWMCR)
PWM7E–PWM0E — PWM Output Enable Bits
Setting a PWMxE bit to logic 1 configures the PTBx/PWMx pin for
PWM output function. Reset clears the PWMxE bits.
1 = PTBx/PWMx pin configured as PWMx interrupt pin
0 = PTBx/PWMx pin configured as PTBx standard I/O pin
Data Sheet
302
MC68HC908LD64 — Rev. 3.0
Input/Output (I/O) Ports
Freescale Semiconductor
Input/Output (I/O) Ports
Port C
19.5 Port C
Port C is an 7-bit special-function port that shares six of its pins with the
analog-to-digital converter (ADC) module. (See Section 13. Analog-toDigital Converter (ADC).)
19.5.1 Port C Data Register
The port C data register (PTC) contains a data latch for each of the
seven port C pins.
Address:
$0002
Bit 7
Read:
6
5
4
3
2
1
Bit 0
PTC6
PTC5
PTC4
PTC3
PTC2
PTC1
PTC0
ADC2
ADC1
ADC0
0
Write:
Reset:
Alternative Function:
Unaffected by reset
ADC5
ADC4
ADC3
= Unimplemented
Figure 19-10. Port C Data Register (PTC)
PTC[6:0] — Port C Data Bits
These read/write bits are software-programmable. Data direction of
each port C pin is under the control of the corresponding bit in data
direction register C. Reset has no effect on port C data.
ADC[5:0] — Analog-to-Digital Input Pins
ADC[5:0] are pins used for the input channels to the analog-to-digital
converter module. The channel select bits, ADCH[4:0], in the ADC
Status and Control Register define which port C pin will be used as
an ADC input and overrides any control from the port I/O logic. (See
19.5.3 Port C Options and Section 13. Analog-to-Digital
Converter (ADC).)
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Input/Output (I/O) Ports
303
Input/Output (I/O) Ports
NOTE:
Care must be taken when reading port C while applying analog voltages
to ADC5–ADC0 pins. If the appropriate ADC channel is not enabled,
excessive current drain may occur if analog voltages are applied to the
PTCx/ADCx pin, while PTC is read as a digital input. Those ports not
selected as analog input channels are considered digital I/O ports.
19.5.2 Data Direction Register C
Data direction register C (DDRC) determines whether each port C pin is
an input or an output. Writing a logic 1 to a DDRC bit enables the output
buffer for the corresponding port C pin; a logic 0 disables the output
buffer.
Address:
$0006
Bit 7
Read:
6
5
4
3
2
1
Bit 0
DDRC6
DDRC5
DDRC4
DDRC3
DDRC2
DDRC1
DDRC0
0
0
0
0
0
0
0
0
Write:
Reset:
0
= Unimplemented
Figure 19-11. Data Direction Register C (DDRC)
DDRC[6:0] — Data Direction Register C Bits
These read/write bits control port C data direction. Reset clears
DDRC[6:0], configuring all port C pins as inputs.
1 = Corresponding port C pin configured as output
0 = Corresponding port C pin configured as input
NOTE:
Avoid glitches on port C pins by writing to the port C data register before
changing data direction register C bits from 0 to 1.
Figure 19-12 shows the port C I/O logic.
Data Sheet
304
MC68HC908LD64 — Rev. 3.0
Input/Output (I/O) Ports
Freescale Semiconductor
Input/Output (I/O) Ports
Port C
READ DDRC ($0006)
INTERNAL DATA BUS
WRITE DDRC ($0006)
RESET
DDRCx
WRITE PTC ($0002)
PTCx
PTCx
READ PTC ($0002)
Figure 19-12. Port C I/O Circuit
When bit DDRCx is a logic 1, reading address $0002 reads the PTCx
data latch. When bit DDRCx is a logic 0, reading address $0002 reads
the voltage level on the pin. The data latch can always be written,
regardless of the state of its data direction bit. Table 19-4 summarizes
the operation of the port C pins.
Table 19-4. Port C Pin Functions
Accesses to DDRC
DDRC
Bit
PTC Bit
0
X(1)
1
X
Accesses to PTC
I/O Pin Mode
Read/Write
Read
Write
Input, Hi-Z(2)
DDRC[6:0]
Pin
PTC[6:0](3)
Output
DDRC[6:0]
PTC[6:0]
PTC[6:0]
Notes:
1. X = don’t care.
2. Hi-Z = high impedance.
3. Writing affects data register, but does not affect input.
19.5.3 Port C Options
The ADCH[4:0] bits in the ADC Status and Control Register defines
which PTCx/ADCx pin is used as an ADC input and overrides any control
from the port I/O logic by forcing that pin as the input to the analog
circuitry. (See Section 13. Analog-to-Digital Converter (ADC).)
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Input/Output (I/O) Ports
305
Input/Output (I/O) Ports
19.6 Port D
Port D is an 8-bit special-function port that shares two of its pins with the
multi-master IIC (MMIIC) module, two of its pins with the DDC12AB
module, and four of its pins with the sync processor.
19.6.1 Port D Data Register
The port D data register (PTD) contains a data latch for each of the eight
port D pins.
Address:
$0003
Bit 7
6
5
4
3
2
1
Bit 0
PTD7
PTD6
PTD5
PTD4
PTD3
PTD2
PTD1
PTD0
VOUT
DE
DCLK
Read:
Write:
Reset:
Alternative Function:
Unaffected by reset
IICSDA
IICSCL
DDCSDA DDCSCL
HOUT
Figure 19-13. Port D Data Register (PTD)
PTD[7:0] — Port D Data Bits
These read/write bits are software-programmable. Data direction of
each port D pin is under the control of the corresponding bit in data
direction register D. Reset has no effect on port D data.
IICSDA, IICSCL — Multi-master IIC Data and Clock pins
The PTD7/IICSDA and PTD6/IICSCL pins are multi-master IIC data
and clock pins. When the IICDATE and IICSCLE bits in the port D
control register (PDCR) are clear, the PTD7/IICSDA and
PTD6/IICSCL pins are available for general-purpose I/O.
(See 19.6.3 Port D Options.)
DDCSCL, DDCSDA — DDC12AB Data and Clock pins
The PTD4/DDCSCL and PTD5/DDCSDA pins are DDC12AB clock
and data pins respectively. When the DDCSCLE and DDCDATE bits
in the port D control register (PDCR) are clear, the PTD4/DDCSCL
and PTD5/DDCSDA pins are available for general-purpose I/O. (See
19.6.3 Port D Options.)
Data Sheet
306
MC68HC908LD64 — Rev. 3.0
Input/Output (I/O) Ports
Freescale Semiconductor
Input/Output (I/O) Ports
Port D
HOUT— Sync Processor HOUT Pulse Output Pin
The PTD3/HOUT pin is the sync processor HOUT pulse output pin.
When the HOUTE bit in the port D control register (PDCR) is clear,
the PTD3/HOUT pin is available for general-purpose I/O. (See 19.6.3
Port D Options.)
VOUT — Sync Processor VOUT Pulse Output Pin
The PTD2/VOUT pin is the sync processor VOUT pulse output pin.
When the VOUTE bit in the port D control register (PDCR) is clear, the
PTD2/VOUT pin is available for general-purpose I/O. (See 19.6.3
Port D Options.)
DE — Sync Processor DE Pulse Output Pin
The PTD1/DE pin is the sync processor DE pulse output pin. When
the DEE bit in the port D control register (PDCR) is clear, the
PTD1/DE pin is available for general-purpose I/O. (See 19.6.3 Port D
Options.)
DCLK — Sync Processor DCLK Pulse Output Pin
The PTD0/DCLK pin is the sync processor DCLK pulse output pin.
When the DCLKE bit in the port D control register (PDCR) is clear, the
PTD0/DCLK pin is available for general-purpose I/O. (See 19.6.3
Port D Options.)
19.6.2 Data Direction Register D
Data direction register D (DDRD) determines whether each port D pin is
an input or an output. Writing a logic 1 to a DDRD bit enables the output
buffer for the corresponding port D pin; a logic 0 disables the output
buffer.
Address:
$0007
Bit 7
6
5
4
3
2
1
Bit 0
DDRD7
DDRD6
DDRD5
DDRD4
DDRD3
DDRD2
DDRD1
DDRD0
0
0
0
0
0
0
0
0
Read:
Write:
Reset:
Figure 19-14. Data Direction Register D (DDRD)
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Input/Output (I/O) Ports
307
Input/Output (I/O) Ports
DDRD[7:0] — Data Direction Register D Bits
These read/write bits control port D data direction. Reset clears
DDRD[7:0], configuring all port D pins as inputs.
1 = Corresponding port D pin configured as output
0 = Corresponding port D pin configured as input
NOTE:
Avoid glitches on port D pins by writing to the port D data register before
changing data direction register D bits from 0 to 1.
Figure 19-15 shows the port D I/O logic.
READ DDRD ($0007)
INTERNAL DATA BUS
WRITE DDRD ($0007)
DDRDx
RESET
WRITE PTD ($0003)
PTDx
PTDx
READ PTD ($0003)
Figure 19-15. Port D I/O Circuit
When bit DDRDx is a logic 1, reading address $0003 reads the PTDx
data latch. When bit DDRDx is a logic 0, reading address $0003 reads
the voltage level on the pin. The data latch can always be written,
regardless of the state of its data direction bit. Table 19-5 summarizes
the operation of the port D pins.
Table 19-5. Port D Pin Functions
DDRD
Bit
PTD Bit
I/O Pin
Mode
Accesses
to DDRD
Accesses to PTD
Read/Write
Read
Write
0
X(1)
Input, Hi-Z(2)
DDRD[7:0]
Pin
PTD[7:0](3)
1
X
Output
DDRD[7:0]
PTD[7:0]
PTD[7:0]
Notes:
1. X = don’t care.
2. Hi-Z = high impedance.
3. Writing affects data register, but does not affect the input.
Data Sheet
308
MC68HC908LD64 — Rev. 3.0
Input/Output (I/O) Ports
Freescale Semiconductor
Input/Output (I/O) Ports
Port D
19.6.3 Port D Options
The port D control register (PDCR) selects the port D pins for module
function or as standard I/O function.
Address:
$0069
Bit 7
6
5
4
3
2
1
Bit 0
HOUTE
VOUTE
DEE
DCLKE
0
0
0
0
Read:
IICDATE
IICSCLE DDCDATE DDCSCLE
Write:
Reset:
0
0
0
0
Figure 19-16. Port D Control Register (PDCR)
IICDATE — MMIIC Data Pin Enable
This bit is set to configure the PTD7/IICSDA pin for IICSDA function.
Reset clears this bit.
1 = PTD7/IICSDA pin configured as IICSDA pin
0 = PTD7/IICSDA pin configured as standard I/O pin
IICSCLE — MMIIC Clock Pin Enable
This bit is set to configure the PTD6/IICSCL pin for IICSCL function.
Reset clears this bit.
1 = PTD6/IICSCL pin configured as IICSCL pin
0 = PTD6/IICSCL pin configured as standard I/O pin
DDCDATE — DDC Data Pin Enable
This bit is set to configure the PTD5/DDCSDA pin for DDCSDA
function. Reset clears this bit.
1 = PTD5/DDCSDA pin configured as DDCSDA pin
0 = PTD5/DDCSDA pin configured as standard I/O port
DDCSCLE — DDC Clock Pin Enable
This bit is set to configure the PTD4/DDCSCL pin for DDCSCL
function. Reset clears this bit.
1 = PTD4/DDCSCL pin configured as DDCSCL pin
0 = PTD4/DDCSCL pin configured as standard I/O port
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Input/Output (I/O) Ports
309
Input/Output (I/O) Ports
HOUTE — HOUT Pin Enable
This bit is set to configure the PTD3/HOUT pin for sync processor
HOUT output. Reset clears this bit.
1 = PTD3/HOUT pin configured as HOUT pin
0 = PTD3/HOUT pin configured as standard I/O pin
VOUTE — VOUT Pin Enable
This bit is set to configure the PTD2/VOUT pin for sync processor
VOUT output. Reset clears this bit.
1 = PTD2/VOUT pin configured as VOUT pin
0 = PTD2/VOUT pin configured as standard I/O pin
DEE — DE Pin Enable
This bit is set to configure the PTD1/DE pin for sync processor DE
output. Reset clears this bit.
1 = PTD1/DE pin configured as DE pin
0 = PTD1/DE pin configured as standard I/O pin
DCLKE — DCLK Pin Enable
This bit is set to configure the PTD0/DCLK pin for sync processor
DCLK output. Reset clears this bit.
1 = PTD0/DCLK pin configured as DCLK pin
0 = PTD0/DCLK pin configured as standard I/O pin
Data Sheet
310
MC68HC908LD64 — Rev. 3.0
Input/Output (I/O) Ports
Freescale Semiconductor
Input/Output (I/O) Ports
Port E
19.7 Port E
Port E is an 8-bit special-function port that shares all of its pins with the
universal serial bus module. (See Section 14. Universal Serial Bus
Module (USB).)
19.7.1 Port E Data Register
The port E data register (PTE) contains a data latch for each of the eight
port E pins.
Address:
$0008
Bit 7
6
5
4
3
2
1
Bit 0
PTE7
PTE6
PTE5
PTE4
PTE3
PTE2
PTE1
PTE0
Read:
Write:
Reset:
Unaffected by reset
Alternative Function: DMINUS4 DPLUS4 DMINUS3 DPLUS3 DMINUS2 DPLUS2 DMINUS1 DPLUS1
Figure 19-17. Port E Data Register (PTE)
PTE[7:0] — Port E Data Bits
These read/write bits are software-programmable. Data direction of
each port E pin is under the control of the corresponding bit in data
direction register E. Reset has no effect on port E data.
DPLUSx and DMINUSx — Downstream Pairs of USB HUB Data Pins
The DPLUSx and DMINUSx pins are the data pin pairs of the
universal serial bus HUB. When the USBDSxE bit in the port E control
register (PECR) is clear, the corresponding PTE/DPLUSx and
PTE/DMINUSx pins are available for general-purpose I/O. (See
19.7.3 Port E Options.).
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Input/Output (I/O) Ports
311
Input/Output (I/O) Ports
19.7.2 Data Direction Register E
Data direction register E (DDRE) determines whether each port E pin is
an input or an output. Writing a logic 1 to a DDRE bit enables the output
buffer for the corresponding port E pin; a logic 0 disables the output
buffer.
Address:
$0009
Bit 7
6
5
4
3
2
1
Bit 0
DDRE7
DDRE6
DDRE5
DDRE4
DDRE3
DDRE2
DDRE1
DDRE0
0
0
0
0
0
0
0
0
Read:
Write:
Reset:
Figure 19-18. Data Direction Register E (DDRE)
DDRE[7:0] — Data Direction Register E Bits
These read/write bits control port E data direction. Reset clears
DDRE[7:0], configuring all port E pins as inputs.
1 = Corresponding port E pin configured as output
0 = Corresponding port E pin configured as input
NOTE:
Avoid glitches on port E pins by writing to the port E data register before
changing data direction register E bits from 0 to 1.
Figure 19-19 shows the port E I/O logic.
READ DDRE ($0009)
INTERNAL DATA BUS
WRITE DDRE ($0009)
RESET
DDREx
WRITE PTE ($0008)
PTEx
PTEx
READ PTE ($0008)
Figure 19-19. Port E I/O Circuit
Data Sheet
312
MC68HC908LD64 — Rev. 3.0
Input/Output (I/O) Ports
Freescale Semiconductor
Input/Output (I/O) Ports
Port E
When bit DDREx is a logic 1, reading address $0008 reads the PTEx
data latch. When bit DDREx is a logic 0, reading address $0008 reads
the voltage level on the pin. The data latch can always be written,
regardless of the state of its data direction bit. Table 19-6 summarizes
the operation of the port E pins.
Table 19-6. Port E Pin Functions
DDRE
Bit
PTE Bit
Accesses
to DDRE
I/O Pin
Mode
Accesses to PTD
Read/Write
Read
Write
0
X(1)
Input, Hi-Z(2)
DDRE[7:0]
Pin
PTE[7:0](3)
1
X
Output
DDRE[7:0]
PTE[7:0]
PTE[7:0]
Notes:
1. X = don’t care.
2. Hi-Z = high impedance.
3. Writing affects data register, but does not affect the input.
19.7.3 Port E Options
The Port E control register (PECR) selects the port E pins for USB
module function or as standard I/O function.
Address:
$0068
Bit 7
6
5
4
3
2
1
Bit 0
Read:
R
USBDS4E USBDS3E USBDS2E USBDS1E
Write:
Reset:
0
0
0
0
= Unimplemented
Figure 19-20. Port E Control Register (PECR)
USBDS4E–USBDS1E — USB HUB Data Pins Enable
Setting a USBDSxE bit to logic 1 configures the corresponding
PTE/DPLUSx and PTE/DMINUSx pins for USB HUB downstream
port function. Reset clears the USBDSxE bits.
1 = PTE/DPLUSx and PTE/DMINUSx pins configured as USB pins
0 = PTE/DPLUSx and PTE/DMINUSx pins configured as standard
I/O pins
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Input/Output (I/O) Ports
313
Input/Output (I/O) Ports
Data Sheet
314
MC68HC908LD64 — Rev. 3.0
Input/Output (I/O) Ports
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 20. External Interrupt (IRQ)
20.1 Contents
20.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315
20.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315
20.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .316
20.4.1 IRQ Pin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318
20.5
IRQ Status and Control Register (INTSCR) . . . . . . . . . . . . . . 319
20.6
IRQ Module During Break Interrupts . . . . . . . . . . . . . . . . . . . 320
20.2 Introduction
The IRQ (external interrupt) module provides a maskable interrupt input.
20.3 Features
Features of the IRQ module include the following:
•
A dedicated external interrupt pin, IRQ
•
IRQ interrupt control bits
•
Hysteresis buffer
•
Programmable edge-only or edge and level interrupt sensitivity
•
Automatic interrupt acknowledge
•
Internal pull-up resistor
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
External Interrupt (IRQ)
315
External Interrupt (IRQ)
20.4 Functional Description
A logic 0 applied to the external interrupt pin can latch a CPU interrupt
request. Figure 20-1 shows the structure of the IRQ module.
Interrupt signals on the IRQ pin are latched into the IRQ latch. An
interrupt latch remains set until one of the following actions occurs:
•
Vector fetch — A vector fetch automatically generates an interrupt
acknowledge signal that clears the IRQ latch.
•
Software clear — Software can clear the interrupt latch by writing
to the acknowledge bit in the interrupt status and control register
(INTSCR). Writing a logic 1 to the ACK bit clears the IRQ latch.
•
Reset — A reset automatically clears the interrupt latch.
The external interrupt pin is falling-edge-triggered and is softwareconfigurable to be either falling-edge or falling-edge and low-leveltriggered. The MODE bit in the INTSCR controls the triggering sensitivity
of the IRQ pin.
When the interrupt pin is edge-triggered only, the CPU interrupt request
remains set until a vector fetch, software clear, or reset occurs.
When the interrupt pin is both falling-edge and low-level-triggered, the
CPU interrupt request remains set until both of the following occur:
•
Vector fetch or software clear
•
Return of the interrupt pin to logic 1
The vector fetch or software clear may occur before or after the interrupt
pin returns to logic 1. As long as the pin is low, the interrupt request
remains pending. A reset will clear the latch and the MODE control bit,
thereby clearing the interrupt even if the pin stays low.
When set, the IMASK bit in the INTSCR mask all external interrupt
requests. A latched interrupt request is not presented to the interrupt
priority logic unless the IMASK bit is clear.
Data Sheet
316
MC68HC908LD64 — Rev. 3.0
External Interrupt (IRQ)
Freescale Semiconductor
External Interrupt (IRQ)
Functional Description
NOTE:
The interrupt mask (I) in the condition code register (CCR) masks all
interrupt requests, including external interrupt requests. (See 9.6
Exception Control.)
INTERNAL ADDRESS BUS
ACK
RESET
TO CPU FOR
BIL/BIH
INSTRUCTIONS
VECTOR
FETCH
DECODER
VDD
INTERNAL
PULL-UP
VDD
IRQF
DEVICE
D
CLR
Q
CK
IRQ
SYNCHRONIZER
IRQ
INTERRUPT
REQUEST
HIGH
VOLTAGE
DETECT
TO MODE
SELECT
LOGIC
IRQ
FF
IMASK
MODE
Figure 20-1. IRQ Module Block Diagram
Addr.
$001E
Register Name
Read:
IRQ Status and Control
Register Write:
(INTSCR)
Reset:
Bit 7
6
5
4
3
2
0
0
0
0
IRQF
0
ACK
0
0
0
0
0
0
1
Bit 0
IMASK
MODE
0
0
= Unimplemented
Figure 20-2. IRQ I/O Register Summary
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
External Interrupt (IRQ)
317
External Interrupt (IRQ)
20.4.1 IRQ Pin
A logic 0 on the IRQ pin can latch an interrupt request into the IRQ latch.
A vector fetch, software clear, or reset clears the IRQ latch.
If the MODE bit is set, the IRQ pin is both falling-edge-sensitive and lowlevel-sensitive. With MODE set, both of the following actions must occur
to clear IRQ:
•
Vector fetch or software clear — A vector fetch generates an
interrupt acknowledge signal to clear the latch. Software may
generate the interrupt acknowledge signal by writing a logic 1 to
the ACK bit in the interrupt status and control register (INTSCR).
The ACK bit is useful in applications that poll the IRQ pin and
require software to clear the IRQ latch. Writing to the ACK bit prior
to leaving an interrupt service routine can also prevent spurious
interrupts due to noise. Setting ACK does not affect subsequent
transitions on the IRQ pin. A falling edge that occurs after writing
to the ACK bit latches another interrupt request. If the IRQ mask
bit, IMASK, is clear, the CPU loads the program counter with the
vector address at locations $FFFA and $FFFB.
•
Return of the IRQ pin to logic 1 — As long as the IRQ pin is at
logic 0, IRQ remains active.
The vector fetch or software clear and the return of the IRQ pin to logic 1
may occur in any order. The interrupt request remains pending as long
as the IRQ pin is at logic 0. A reset will clear the latch and the MODE
control bit, thereby clearing the interrupt even if the pin stays low.
If the MODE bit is clear, the IRQ pin is falling-edge-sensitive only. With
MODE clear, a vector fetch or software clear immediately clears the IRQ
latch.
The IRQF bit in the INTSCR register can be used to check for pending
interrupts. The IRQF bit is not affected by the IMASK bit, which makes it
useful in applications where polling is preferred.
Use the BIH or BIL instruction to read the logic level on the IRQ pin.
NOTE:
When using the level-sensitive interrupt trigger, avoid false interrupts by
masking interrupt requests in the interrupt routine.
Data Sheet
318
MC68HC908LD64 — Rev. 3.0
External Interrupt (IRQ)
Freescale Semiconductor
External Interrupt (IRQ)
IRQ Status and Control Register (INTSCR)
20.5 IRQ Status and Control Register (INTSCR)
The IRQ status and control register (INTSCR) controls and monitors
operation of the IRQ module. The INTSCR has the following functions:
•
Shows the state of the IRQ flag
•
Clears the IRQ latch
•
Masks IRQ interrupt request
•
Controls triggering sensitivity of the IRQ interrupt pin
Address:
Read:
$001E
Bit 7
6
5
4
3
2
0
0
0
0
IRQF
0
Bit 0
IMASK
MODE
0
0
ACK
Write:
Reset:
1
0
0
0
0
0
0
= Unimplemented
Figure 20-3. IRQ Status and Control Register (INTSCR)
IRQF — IRQ Flag
This read-only status bit is high when the IRQ interrupt is pending.
1 = IRQ interrupt pending
0 = IRQ interrupt not pending
ACK — IRQ Interrupt Request Acknowledge Bit
Writing a logic 1 to this write-only bit clears the IRQ latch. ACK always
reads as logic 0. Reset clears ACK.
IMASK — IRQ Interrupt Mask Bit
Writing a logic 1 to this read/write bit disables IRQ interrupt requests.
Reset clears IMASK.
1 = IRQ interrupt requests disabled
0 = IRQ interrupt requests enabled
MODE — IRQ Edge/Level Select Bit
This read/write bit controls the triggering sensitivity of the IRQ pin.
Reset clears MODE.
1 = IRQ interrupt requests on falling edges and low levels
0 = IRQ interrupt requests on falling edges only
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
External Interrupt (IRQ)
319
External Interrupt (IRQ)
20.6 IRQ Module During Break Interrupts
The system integration module (SIM) controls whether the IRQ latch can
be cleared during the break state. The BCFE bit in the break flag control
register (BFCR) enables software to clear the latches during the break
state. (See Section 9. System Integration Module (SIM).)
To allow software to clear the IRQ latch during a break interrupt, write a
logic 1 to the BCFE bit. If a latch is cleared during the break state, it
remains cleared when the MCU exits the break state.
To protect the latches during the break state, write a logic 0 to the BCFE
bit. With BCFE at logic 0 (its default state), writing to the ACK bit in the
IRQ status and control register during the break state has no effect on
the IRQ latch.
Data Sheet
320
MC68HC908LD64 — Rev. 3.0
External Interrupt (IRQ)
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 21. Keyboard Interrupt Module (KBI)
21.1 Contents
21.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321
21.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
21.4
I/O Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
21.5
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .323
21.6
Keyboard Initialization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
21.7 I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
21.7.1 Keyboard Status and Control Register. . . . . . . . . . . . . . . . 326
21.7.2 Keyboard Interrupt Enable Register . . . . . . . . . . . . . . . . . . 327
21.8 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327
21.8.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .327
21.8.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .327
21.9
Keyboard Module During Break Interrupts . . . . . . . . . . . . . . . 328
21.2 Introduction
The keyboard interrupt module (KBI) provides eight independently
maskable external interrupts which are accessible via PTA0–PTA7.
When a port pin is enabled for keyboard interrupt function, an internal
pull-up device is also enabled on the pin.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Keyboard Interrupt Module (KBI)
321
Keyboard Interrupt Module (KBI)
21.3 Features
Features of the keyboard interrupt module (KBI) include:
•
Eight keyboard interrupt pins with pull-up devices
•
Separate keyboard interrupt enable bits and one keyboard
interrupt mask
•
Programmable edge-only or edge- and level- interrupt sensitivity
•
Exit from low-lower modes
Addr.
Register Name
$004E
Keyboard Status and Read:
Control Register Write:
(KBSCR)
Reset:
Keyboard Interrupt Enable Read:
$004F
Register Write:
(KBIER)
Reset:
Bit 7
6
5
4
3
2
0
0
0
0
KEYF
0
ACKK
1
Bit 0
IMASKK
MODEK
0
0
0
0
0
0
0
0
KBIE7
KBIE6
KBIE5
KBIE4
KBIE3
KBIE2
KBIE1
KBIE0
0
0
0
0
0
0
0
0
= Unimplemented
Figure 21-1. KBI I/O Register Summary
21.4 I/O Pins
The eight keyboard interrupt pins are shared with standard port I/O pins.
The full name of the KBI pins are listed in Table 21-1. The generic pin
name appear in the text that follows.
Table 21-1. Pin Name Conventions
KBI
Generic Pin Name
Full MCU Pin Name
Pin Selected for KBI Function by
KBIEx Bit in KBIER
KBI0–KBI7
PTA0/KBI0–PTA7/KBI7
KBIE0–KBIE7
Data Sheet
322
MC68HC908LD64 — Rev. 3.0
Keyboard Interrupt Module (KBI)
Freescale Semiconductor
Keyboard Interrupt Module (KBI)
Functional Description
21.5 Functional Description
INTERNAL BUS
KBI0
ACKK
VDD
VECTOR FETCH
DECODER
KEYF
RESET
.
KBIE0
D
CLR
Q
SYNCHRONIZER
.
CK
TO PULL-UP ENABLE
.
KEYBOARD
INTERRUPT FF
KBI7
Keyboard
Interrupt
Request
IMASKK
MODEK
KBIE7
TO PULL-UP ENABLE
Figure 21-2. Keyboard Interrupt Module Block Diagram
Writing to the KBIE7–KBIE0 bits in the keyboard interrupt enable register
independently enables or disables each port A pin as a keyboard
interrupt pin. Enabling a keyboard interrupt pin also enables its internal
pull-up device. A logic 0 applied to an enabled keyboard interrupt pin
latches a keyboard interrupt request.
A keyboard interrupt is latched when one or more keyboard pins goes
low after all were high. The MODEK bit in the keyboard status and
control register controls the triggering mode of the keyboard interrupt.
•
If the keyboard interrupt is edge-sensitive only, a falling edge on a
keyboard pin does not latch an interrupt request if another
keyboard pin is already low. To prevent losing an interrupt request
on one pin because another pin is still low, software can disable
the latter pin while it is low.
•
If the keyboard interrupt is falling edge- and low level-sensitive, an
interrupt request is present as long as any keyboard pin is low.
If the MODEK bit is set, the keyboard interrupt pins are both falling edgeand low level-sensitive, and both of the following actions must occur to
clear a keyboard interrupt request:
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Keyboard Interrupt Module (KBI)
323
Keyboard Interrupt Module (KBI)
•
Vector fetch or software clear — A vector fetch generates an
interrupt acknowledge signal to clear the interrupt request.
Software may generate the interrupt acknowledge signal by
writing a logic 1 to the ACKK bit in the keyboard status and control
register (KBSCR). The ACKK bit is useful in applications that poll
the keyboard interrupt pins and require software to clear the
keyboard interrupt request. Writing to the ACKK bit prior to leaving
an interrupt service routine also can prevent spurious interrupts
due to noise. Setting ACKK does not affect subsequent transitions
on the keyboard interrupt pins. A falling edge that occurs after
writing to the ACKK bit latches another interrupt request. If the
keyboard interrupt mask bit, IMASKK, is clear, the CPU loads the
program counter with the vector address at locations $FFE2 and
$FFE3.
•
Return of all enabled keyboard interrupt pins to logic 1 — As long
as any enabled keyboard interrupt pin is at logic 0, the keyboard
interrupt remains set.
The vector fetch or software clear and the return of all enabled keyboard
interrupt pins to logic 1 may occur in any order.
If the MODEK bit is clear, the keyboard interrupt pin is falling-edgesensitive only. With MODEK clear, a vector fetch or software clear
immediately clears the keyboard interrupt request.
Reset clears the keyboard interrupt request and the MODEK bit, clearing
the interrupt request even if a keyboard interrupt pin stays at logic 0.
The keyboard flag bit (KEYF) in the keyboard status and control register
can be used to see if a pending interrupt exists. The KEYF bit is not
affected by the keyboard interrupt mask bit (IMASKK) which makes it
useful in applications where polling is preferred.
To determine the logic level on a keyboard interrupt pin, use the data
direction register to configure the pin as an input and read the data
register.
NOTE:
Setting a keyboard interrupt enable bit (KBIEx) forces the corresponding
keyboard interrupt pin to be an input, overriding the data direction
register. However, the data direction register bit must be a logic 0 for
software to read the pin.
Data Sheet
324
MC68HC908LD64 — Rev. 3.0
Keyboard Interrupt Module (KBI)
Freescale Semiconductor
Keyboard Interrupt Module (KBI)
Keyboard Initialization
21.6 Keyboard Initialization
When a keyboard interrupt pin is enabled, it takes time for the pull-up
device to reach a logic 1. Therefore, a false interrupt can occur as soon
as the pin is enabled.
To prevent a false interrupt on keyboard initialization:
1. Mask keyboard interrupts by setting the IMASKK bit in the
keyboard status and control register.
2. Enable the KBI pins by setting the appropriate KBIEx bits in the
keyboard interrupt enable register.
3. Write to the ACKK bit in the keyboard status and control register
to clear any false interrupts.
4. Clear the IMASKK bit.
An interrupt signal on an edge-triggered pin can be acknowledged
immediately after enabling the pin. An interrupt signal on an edge- and
level-triggered interrupt pin must be acknowledged after a delay that
depends on the external load.
Another way to avoid a false interrupt:
1. Configure the keyboard pins as outputs by setting the appropriate
DDRA bits in data direction register A.
2. Write logic 1s to the appropriate port A data register bits.
3. Enable the KBI pins by setting the appropriate KBIEx bits in the
keyboard interrupt enable register.
21.7 I/O Registers
These registers control and monitor operation of the keyboard module:
•
Keyboard status and control register (KBSCR)
•
Keyboard interrupt enable register (KBIER)
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Keyboard Interrupt Module (KBI)
325
Keyboard Interrupt Module (KBI)
21.7.1 Keyboard Status and Control Register
•
Flags keyboard interrupt requests
•
Acknowledges keyboard interrupt requests
•
Masks keyboard interrupt requests
•
Controls keyboard interrupt triggering sensitivity
Address:
Read:
$004E
Bit 7
6
5
4
3
2
0
0
0
0
KEYF
0
Write:
Reset:
1
Bit 0
IMASKK
MODEK
0
0
ACKK
0
0
0
0
0
0
= Unimplemented
Figure 21-3. Keyboard Status and Control Register (KBSCR)
KEYF — Keyboard Flag Bit
This read-only bit is set when a keyboard interrupt is pending. Reset
clears the KEYF bit.
1 = Keyboard interrupt pending
0 = No keyboard interrupt pending
ACKK — Keyboard Acknowledge Bit
Writing a logic 1 to this write-only bit clears the keyboard interrupt
request. ACKK always reads as logic 0. Reset clears ACKK.
IMASKK — Keyboard Interrupt Mask Bit
Writing a logic 1 to this read/write bit prevents the output of the
keyboard interrupt mask from generating interrupt requests. Reset
clears the IMASKK bit.
1 = Keyboard interrupt requests masked
0 = Keyboard interrupt requests not masked
MODEK — Keyboard Triggering Sensitivity Bit
This read/write bit controls the triggering sensitivity of the keyboard
interrupt pins. Reset clears MODEK.
1 = Keyboard interrupt requests on falling edges and low levels
0 = Keyboard interrupt requests on falling edges only
Data Sheet
326
MC68HC908LD64 — Rev. 3.0
Keyboard Interrupt Module (KBI)
Freescale Semiconductor
Keyboard Interrupt Module (KBI)
Low-Power Modes
21.7.2 Keyboard Interrupt Enable Register
The keyboard interrupt enable register enables or disables each port A
pin to operate as a keyboard interrupt pin.
Address:
$004F
Bit 7
6
5
4
3
2
1
Bit 0
KBIE7
KBIE6
KBIE5
KBIE4
KBIE3
KBIE2
KBIE1
KBIE0
0
0
0
0
0
0
0
0
Read:
Write:
Reset:
Figure 21-4. Keyboard Interrupt Enable Register (KBIER)
KBIE7–KBIE0 — Keyboard Interrupt Enable Bits
Each of these read/write bits enables the corresponding keyboard
interrupt pin to latch interrupt requests. Reset clears the keyboard
interrupt enable register.
1 = PTAx/KBIx pin enabled as keyboard interrupt pin
0 = PTAx/KBIx pin not enabled as keyboard interrupt pin
21.8 Low-Power Modes
The WAIT and STOP instructions put the MCU in low-powerconsumption standby modes.
21.8.1 Wait Mode
The keyboard interrupt module remains active in wait mode. Clearing the
IMASKK bit in the keyboard status and control register enables keyboard
interrupt requests to bring the MCU out of wait mode.
21.8.2 Stop Mode
The keyboard interrupt module remains active in stop mode. Clearing
the IMASKK bit in the keyboard status and control register enables
keyboard interrupt requests to bring the MCU out of stop mode.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Keyboard Interrupt Module (KBI)
327
Keyboard Interrupt Module (KBI)
21.9 Keyboard Module During Break Interrupts
The system integration module (SIM) controls whether the keyboard
interrupt latch can be cleared during the break state. The BCFE bit in the
break flag control register (BFCR) enables software to clear status bits
during the break state.
To allow software to clear the keyboard interrupt latch during a break
interrupt, write a logic 1 to the BCFE bit. If a latch is cleared during the
break state, it remains cleared when the MCU exits the break state.
To protect the latch during the break state, write a logic 0 to the BCFE
bit. With BCFE at logic 0 (its default state), writing to the keyboard
acknowledge bit (ACKK) in the keyboard status and control register
during the break state has no effect. (See 21.7.1 Keyboard Status and
Control Register.)
Data Sheet
328
MC68HC908LD64 — Rev. 3.0
Keyboard Interrupt Module (KBI)
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 22. Computer Operating Properly (COP)
22.1 Contents
22.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
22.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .330
22.4 I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331
22.4.1 OSCXCLK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .331
22.4.2 STOP Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331
22.4.3 COPCTL Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .331
22.4.4 Power-On Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331
22.4.5 Internal Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332
22.4.6 Reset Vector Fetch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332
22.4.7 COPD (COP Disable). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332
22.4.8 COPRS (COP Rate Select) . . . . . . . . . . . . . . . . . . . . . . . . 332
22.5
COP Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
22.6
Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .333
22.7
Monitor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .333
22.8 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
22.8.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .334
22.8.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .334
22.9
COP Module During Break Mode . . . . . . . . . . . . . . . . . . . . . . 334
22.2 Introduction
The computer operating properly (COP) module contains a free-running
counter that generates a reset if allowed to overflow. The COP module
helps software recover from runaway code. Prevent a COP reset by
clearing the COP counter periodically. The COP module can be disabled
through the COPD bit in the CONFIG register.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Computer Operating Properly (COP)
329
Computer Operating Properly (COP)
22.3 Functional Description
Figure 22-1 shows the structure of the COP module.
RESET STATUS REGISTER
COP TIMEOUT
CLEAR STAGES 5–12
STOP INSTRUCTION
INTERNAL RESET SOURCES
RESET VECTOR FETCH
RESET CIRCUIT
12-BIT COP PRESCALER
CLEAR ALL STAGES
OSCXCLK
COPCTL WRITE
COP CLOCK
6-BIT COP COUNTER
COPEN (FROM SIM)
COP DISABLE
(COPD FROM CONFIG)
RESET
COPCTL WRITE
CLEAR
COP COUNTER
COP RATE SEL
(COPRS FROM CONFIG)
Figure 22-1. COP Block Diagram
The COP counter is a free-running 6-bit counter preceded by a 12-bit
prescaler counter. If not cleared by software, the COP counter overflows
and generates an asynchronous reset after 218 – 24 or 213 – 24
OSCXCLK cycles, depending on the state of the COP rate select bit,
COPRS, in configuration register 1. With a 218 – 24 OSCXCLK cycle
overflow option, a 24MHz crystal gives a COP timeout period of
10.922ms. Writing any value to location $FFFF before an overflow
occurs prevents a COP reset by clearing the COP counter and stages
12 through 5 of the prescaler.
NOTE:
Service the COP immediately after reset and before entering or after
exiting stop mode to guarantee the maximum time before the first COP
counter overflow.
Data Sheet
330
MC68HC908LD64 — Rev. 3.0
Computer Operating Properly (COP)
Freescale Semiconductor
Computer Operating Properly (COP)
I/O Signals
A COP reset pulls the RST pin low for 32 OSCXCLK cycles and sets the
COP bit in the SIM reset status register (SRSR).
In monitor mode, the COP is disabled if the RST pin or the IRQ is held
at VTST. During the break state, VTST on the RST pin disables the COP.
NOTE:
Place COP clearing instructions in the main program and not in an
interrupt subroutine. Such an interrupt subroutine could keep the COP
from generating a reset even while the main program is not working
properly.
22.4 I/O Signals
The following paragraphs describe the signals shown in Figure 22-1.
22.4.1 OSCXCLK
OSCXCLK is the crystal oscillator output signal. OSCXCLK frequency is
equal to the crystal frequency.
22.4.2 STOP Instruction
The STOP instruction clears the COP prescaler.
22.4.3 COPCTL Write
Writing any value to the COP control register (COPCTL) (see 22.5 COP
Control Register) clears the COP counter and clears bits 12 through 5
of the prescaler. Reading the COP control register returns the low byte
of the reset vector.
22.4.4 Power-On Reset
The power-on reset (POR) circuit clears the COP prescaler 4096
OSCXCLK cycles after power-up.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Computer Operating Properly (COP)
331
Computer Operating Properly (COP)
22.4.5 Internal Reset
An internal reset clears the COP prescaler and the COP counter.
22.4.6 Reset Vector Fetch
A reset vector fetch occurs when the vector address appears on the data
bus. A reset vector fetch clears the COP prescaler.
22.4.7 COPD (COP Disable)
The COPD signal reflects the state of the COP disable bit (COPD) in the
CONFIG register. (See Figure 22-2.)
22.4.8 COPRS (COP Rate Select)
The COPRS signal reflects the state of the COP rate select bit (COPRS)
in the CONFIG register. (See Figure 22-2.)
Address:
Read:
$001F
Bit 7
6
5
4
0
0
0
0
3
2
1
Bit 0
SSREC
COPRS
STOP
COPD
0
0
0
0
Write:
Reset:
0
0
0
0
= Unimplemented
Figure 22-2. Configuration Register (CONFIG)
COPRS — COP Rate Select Bit
COPRS selects the COP timeout period. Reset clears COPRS.
1 = COP timeout period is 213 – 24 OSCXCLK cycles
0 = COP timeout period is 218 – 24 OSCXCLK cycles
COPD — COP Disable Bit
COPD disables the COP module.
1 = COP module disabled
0 = COP module enabled
Data Sheet
332
MC68HC908LD64 — Rev. 3.0
Computer Operating Properly (COP)
Freescale Semiconductor
Computer Operating Properly (COP)
COP Control Register
22.5 COP Control Register
The COP control register is located at address $FFFF and overlaps the
reset vector. Writing any value to $FFFF clears the COP counter and
starts a new timeout period. Reading location $FFFF returns the low
byte of the reset vector.
Address:
$FFFF
Bit 7
6
5
4
3
Read:
Low byte of reset vector
Write:
Clear COP counter
Reset:
Unaffected by reset
2
1
Bit 0
Figure 22-3. COP Control Register (COPCTL)
22.6 Interrupts
The COP does not generate CPU interrupt requests.
22.7 Monitor Mode
When monitor mode is entered with VTST on the IRQ pin, the COP is
disabled as long as VTST remains on the IRQ pin or the RST pin. When
monitor mode is entered by having blank reset vectors and not having
VTST on the IRQ pin, the COP is automatically disabled until a POR
occurs.
22.8 Low-Power Modes
The WAIT and STOP instructions put the MCU in low powerconsumption standby modes.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Computer Operating Properly (COP)
333
Computer Operating Properly (COP)
22.8.1 Wait Mode
The COP remains active during wait mode. To prevent a COP reset
during wait mode, periodically clear the COP counter in a CPU interrupt
routine.
22.8.2 Stop Mode
Stop mode turns off the OSCXCLK input to the COP and clears the COP
prescaler. Service the COP immediately before entering or after exiting
stop mode to ensure a full COP timeout period after entering or exiting
stop mode.
To prevent inadvertently turning off the COP with a STOP instruction, a
configuration option is available that disables the STOP instruction.
When the STOP bit in the configuration register has the STOP
instruction is disabled, execution of a STOP instruction results in an
illegal opcode reset.
22.9 COP Module During Break Mode
The COP is disabled during a break interrupt when VTST is present on
the RST pin.
Data Sheet
334
MC68HC908LD64 — Rev. 3.0
Computer Operating Properly (COP)
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 23. Break Module (BRK)
23.1 Contents
23.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335
23.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336
23.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .336
23.4.1 Flag Protection During Break Interrupts . . . . . . . . . . . . . . . 338
23.4.2 CPU During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . .338
23.4.3 TIM During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . 338
23.4.4 COP During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . 338
23.5 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338
23.5.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .338
23.5.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .339
23.6 Break Module Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339
23.6.1 Break Status and Control Register. . . . . . . . . . . . . . . . . . . 339
23.6.2 Break Address Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 340
23.6.3 SIM Break Status Register . . . . . . . . . . . . . . . . . . . . . . . . . 340
23.6.4 SIM Break Flag Control Register . . . . . . . . . . . . . . . . . . . . 342
23.2 Introduction
This section describes the break module. The break module can
generate a break interrupt that stops normal program flow at a defined
address to enter a background program.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Break Module (BRK)
335
Break Module (BRK)
23.3 Features
Features of the break module include:
•
Accessible input/output (I/O) registers during the break interrupt
•
CPU-generated break interrupts
•
Software-generated break interrupts
•
COP disabling during break interrupts
23.4 Functional Description
When the internal address bus matches the value written in the break
address registers, the break module issues a breakpoint signal to the
CPU. The CPU then loads the instruction register with a software
interrupt instruction (SWI) after completion of the current CPU
instruction. The program counter vectors to $FFFC and $FFFD
($FEFC and $FEFD in monitor mode).
The following events can cause a break interrupt to occur:
•
A CPU-generated address (the address in the program counter)
matches the contents of the break address registers.
•
Software writes a logic 1 to the BRKA bit in the break status and
control register.
When a CPU-generated address matches the contents of the break
address registers, the break interrupt begins after the CPU completes its
current instruction. A return-from-interrupt instruction (RTI) in the break
routine ends the break interrupt and returns the MCU to normal
operation. Figure 23-1 shows the structure of the break module.
Data Sheet
336
MC68HC908LD64 — Rev. 3.0
Break Module (BRK)
Freescale Semiconductor
Break Module (BRK)
Functional Description
IAB15–IAB8
BREAK ADDRESS REGISTER HIGH
8-BIT COMPARATOR
IAB15–IAB0
BREAK
CONTROL
8-BIT COMPARATOR
BREAK ADDRESS REGISTER LOW
IAB7–IAB0
Figure 23-1. Break Module Block Diagram
Addr.
Register Name
Read:
SIM Break Status Register
$FE00
Write:
(SBSR)
Reset:
$FE03
$FE0C
$FE0D
Read:
SIM Break Flag Control
Write:
Register (SBFCR)
Reset:
Read:
Break Address Register
Write:
High (BRKH)
Reset:
Read:
Break Address Register
Write:
Low (BRKL)
Reset:
Read:
Break Status and Control
$FE0E
Write:
Register (BRKSCR)
Reset:
Note: Writing a logic 0 clears SBSW.
Bit 7
6
5
4
3
2
R
R
R
R
R
R
1
SBSW
Note
Bit 0
R
0
BCFE
R
R
R
R
R
R
R
Bit 15
14
13
12
11
10
9
Bit 8
0
0
0
0
0
0
0
0
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
BRKE
BRKA
0
0
0
0
0
0
0
0
0
0
0
0
0
0
R
= Reserved
0
= Unimplemented
Figure 23-2. Break Module I/O Register Summary
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Break Module (BRK)
337
Break Module (BRK)
23.4.1 Flag Protection During Break Interrupts
The BCFE bit in the SIM break flag control register (SBFCR) enables
software to clear status bits during the break state.
23.4.2 CPU During Break Interrupts
The CPU starts a break interrupt by:
•
Loading the instruction register with the SWI instruction
•
Loading the program counter with $FFFC and $FFFD
($FEFC and $FEFD in monitor mode)
The break interrupt begins after completion of the CPU instruction in
progress. If the break address register match occurs on the last cycle of
a CPU instruction, the break interrupt begins immediately.
23.4.3 TIM During Break Interrupts
A break interrupt stops the timer counters.
23.4.4 COP During Break Interrupts
The COP is disabled during a break interrupt when VTST is present on
the RST pin.
23.5 Low-Power Modes
The WAIT and STOP instructions put the MCU in low powerconsumption standby modes.
23.5.1 Wait Mode
If enabled, the break module is active in wait mode. In the break routine,
the user can subtract one from the return address on the stack if SBSW
is set (see Section 9. System Integration Module (SIM)). Clear the
SBSW bit by writing logic 0 to it.
Data Sheet
338
MC68HC908LD64 — Rev. 3.0
Break Module (BRK)
Freescale Semiconductor
Break Module (BRK)
Break Module Registers
23.5.2 Stop Mode
A break interrupt causes exit from stop mode and sets the SBSW bit in
the break status register.
23.6 Break Module Registers
These registers control and monitor operation of the break module:
•
Break status and control register (BRKSCR)
•
Break address register high (BRKH)
•
Break address register low (BRKL)
•
SIM break status register (SBSR)
•
SIM break flag control register (SBFCR)
23.6.1 Break Status and Control Register
The break status and control register (BRKSCR) contains break module
enable and status bits.
Address:
$FE0E
Bit 7
6
BRKE
BRKA
0
0
Read:
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
0
0
0
0
Write:
Reset:
= Unimplemented
Figure 23-3. Break Status and Control Register (BRKSCR)
BRKE — Break Enable Bit
This read/write bit enables breaks on break address register matches.
Clear BRKE by writing a logic 0 to bit 7. Reset clears the BRKE bit.
1 = Breaks enabled on 16-bit address match
0 = Breaks disabled on 16-bit address match
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Break Module (BRK)
339
Break Module (BRK)
BRKA — Break Active Bit
This read/write status and control bit is set when a break address
match occurs. Writing a logic 1 to BRKA generates a break interrupt.
Clear BRKA by writing a logic 0 to it before exiting the break routine.
Reset clears the BRKA bit.
1 = (When read) Break address match
0 = (When read) No break address match
23.6.2 Break Address Registers
The break address registers (BRKH and BRKL) contain the high and low
bytes of the desired breakpoint address. Reset clears the break address
registers.
Address:
$FE0C
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
0
0
0
0
0
0
0
0
Read:
Write:
Reset:
Figure 23-4. Break Address Register High (BRKH)
Address:
$FE0D
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
Read:
Write:
Reset:
Figure 23-5. Break Address Register Low (BRKL)
23.6.3 SIM Break Status Register
The SIM break status register (SBSR) contains a flag to indicate that a
break caused an exit from wait mode. The flag is useful in applications
requiring a return to wait mode after exiting from a break interrupt.
Data Sheet
340
MC68HC908LD64 — Rev. 3.0
Break Module (BRK)
Freescale Semiconductor
Break Module (BRK)
Break Module Registers
Address:
$FE00
Bit 7
6
5
4
3
2
R
R
R
R
R
R
Read:
1
Bit 0
SBSW
R
Write:
Note
Reset:
0
Note: Writing a logic 0 clears SBSW.
R
= Reserved
Figure 23-6. SIM Break Status Register (SBSR)
SBSW — SIM Break Stop/Wait Bit
This status bit is useful in applications requiring a return to wait or stop
mode after exiting from a break interrupt. Clear SBSW by writing a
logic 0 to it. Reset clears SBSW.
1 = Stop mode or wait mode was exited by break interrupt
0 = Stop mode or wait mode was not exited by break interrupt
SBSW can be read within the break interrupt routine. The user can
modify the return address on the stack by subtracting one from it. The
following code is an example.
; This code works if the H register has been pushed onto the stack in the break
; service routine software. This code should be executed at the end of the break
; service routine software.
HIBYTE
EQU
5
LOBYTE
EQU
6
;
If not SBSW, do RTI
BRCLR
SBSW,SBSR, RETURN
; See if wait mode or stop mode was exited by
; break.
TST
LOBYTE,SP
;If RETURNLO is not zero,
BNE
DOLO
;then just decrement low byte.
DEC
HIBYTE,SP
;Else deal with high byte, too.
DOLO
DEC
LOBYTE,SP
;Point to WAIT/STOP opcode.
RETURN
PULH
RTI
;Restore H register.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Break Module (BRK)
341
Break Module (BRK)
23.6.4 SIM Break Flag Control Register
The SIM break flag control register (SBFCR) contains a bit that enables
software to clear status bits while the MCU is in a break state.
Address:
$FE03
Bit 7
6
5
4
3
2
1
Bit 0
BCFE
R
R
R
R
R
R
R
Read:
Write:
Reset:
0
R
= Reserved
Figure 23-7. SIM Break Flag Control Register (SBFCR)
BCFE — Break Clear Flag Enable Bit
This read/write bit enables software to clear status bits by accessing
status registers while the MCU is in a break state. To clear status bits
during the break state, the BCFE bit must be set.
1 = Status bits clearable during break
0 = Status bits not clearable during break
Data Sheet
342
MC68HC908LD64 — Rev. 3.0
Break Module (BRK)
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 24. Electrical Specifications
24.1 Contents
24.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344
24.3
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . 344
24.4
Functional Operating Range. . . . . . . . . . . . . . . . . . . . . . . . . . 345
24.5
Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345
24.6
DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 346
24.7
Control Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347
24.8
TImer Interface Module Characteristics . . . . . . . . . . . . . . . . . 347
24.9
Oscillator Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347
24.10 ADC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 348
24.11 Sync Processor Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349
24.12 USB DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . 349
24.12.1 USB Low Speed Source Electrical Characteristics . . . . . . 350
24.12.2 USB High Speed Source Electrical Characteristics . . . . . . 351
24.12.3 HUB Repeater Electrical Characteristics . . . . . . . . . . . . . . 352
24.12.4 USB Signaling Levels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353
24.13 DDC12AB/MMIIC Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354
24.13.1 DDC12AB/MMIIC Interface Input Signal Timing . . . . . . . . 354
24.13.2 DDC12AB/MMIIC Interface Output Signal Timing . . . . . . . 354
24.14 FLASH Memory Characteristics . . . . . . . . . . . . . . . . . . . . . . . 355
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Electrical Specifications
343
Electrical Specifications
24.2 Introduction
This section contains electrical and timing specifications.
24.3 Absolute Maximum Ratings
Maximum ratings are the extreme limits to which the MCU can be
exposed without permanently damaging it.
NOTE:
This device is not guaranteed to operate properly at the maximum
ratings. Refer to 24.6 DC Electrical Characteristics for guaranteed
operating conditions.
Table 24-1. Absolute Maximum Ratings
Characteristic(1)
Symbol
Value
Unit
Supply voltage
VDD
–0.3 to +3.9
V
Input voltage
VIN
VSS –0.3 to VDD +0.3
V
Input voltage, +5V pins
IICSDA, IICSCL, DDCSDA, DCSCL,
HSYNC, VSYNC, PHSYNC,
PVSYNC, PCLK
VHIN
VSS –0.3 to +5.5
V
I
±25
mA
Storage temperature
TSTG
–55 to +150
°C
Maximum current out of VSS
IMVSS
80
mA
Maximum current into VDD
IMVDD
80
mA
Maximum current per pin
excluding VDD and VSS
Notes:
1. Voltages referenced to VSS.
NOTE:
This device contains circuitry to protect the inputs against damage due
to high static voltages or electric fields; however, it is advised that normal
precautions be taken to avoid application of any voltage higher than
maximum-rated voltages to this high-impedance circuit. For proper
operation, it is recommended that VIN and VOUT be constrained to the
range VSS ≤ (VIN or VOUT) ≤ VDD. Reliability of operation is enhanced if
unused inputs are connected to an appropriate logic voltage level (for
example, either VSS or VDD.)
Data Sheet
344
MC68HC908LD64 — Rev. 3.0
Electrical Specifications
Freescale Semiconductor
Electrical Specifications
Functional Operating Range
24.4 Functional Operating Range
Table 24-2. Operating Range
Characteristic
Symbol
Value
Unit
TA
0 to +85
°C
VDD
3.0 to 3.6
V
Operating temperature range
Operating voltage range
24.5 Thermal Characteristics
Table 24-3. Thermal Characteristics
Characteristic
Symbol
Value
Thermal resistance
QFP (64 pins)
θJA
70
I/O pin power dissipation
PI/O
User determined
W
Power dissipation(1)
PD
PD = (IDD x VDD) + PI/O =
K/(TJ + 273 °C)
W
Constant(2)
K
PD × (TA + 273 °C)
+ PD2 × θJA
W/°C
Average junction temperature
TJ
TA + (PD × θJA)
°C
TJM
100
°C
Maximum junction temperature
Unit
°C/W
Notes:
1. Power dissipation is a function of temperature.
2. K is a constant unique to the device. K can be determined for a known TA and measured
PD. With this value of K, PD and TJ can be determined for any value of TA.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Electrical Specifications
345
Electrical Specifications
24.6 DC Electrical Characteristics
Table 24-4. DC Electrical Characteristics
Characteristic(1)
Symbol
Min
Typ(2)
Max
Unit
Output high voltage (ILOAD = –2.0mA)
All output pins
VOH
2.4
—
—
V
Output low voltage (ILOAD = 1.6mA)
All output pins
VOL
—
—
0.4
V
Input high voltage
All ports (except PTD4–PTD7), IRQ, RST, OSC1
For +5V rated pins
HSYNC, VSYNC, PHSYNC, PVSYNC, PCLK,
IICSDA, IICSCL, DDCSDA, DDCSCL
VIH
0.7 × VDD
—
VDD
V
2.0
—
5.5
Input low voltage
All ports (except PTD4–PTD7), IRQ, RST, OSC1
For +5V rated pins
HSYNC, VSYNC, PHSYNC, PVSYNC, PCLK,
IICSDA, IICSCL, DDCSDA, DDCSCL
VIL
VSS
—
0.2 × VDD
VSS
—
0.8
11
9
6
4
100
20
16
12
8
200
mA
mA
mA
mA
µA
V
VDD supply current
Run, USB active, PLL on, fOP = 6.0 MHz(3)
Run, USB suspended, PLL off, fOP = 6.0 MHz(3)
Wait, USB active, PLL on, fOP = 6.0 MHz(4)
Wait, USB suspended, PLL off, fOP = 6.0 MHz(4)
Stop(5) 0°C to +85°C
IDD
—
—
—
—
—
I/O ports Hi-Z leakage current
IIL
—
—
±10
µA
Input current
All input pins (except below pins)
HSYNC, VSYNC, PHSYNC, PVSYNC, PCLK
IIN
—
—
—
—
±1
±2
µA
Capacitance
Ports (as input or output)
COUT
CIN
—
—
—
—
12
8
pF
POR re-arm voltage(6)
VPOR
0
—
100
mV
POR rise time ramp rate
(7)
RPOR
0.035
—
—
V/ms
Monitor mode entry voltage
VTST
VDD + 1.7
—
6
V
Pull-up resistor: KBI0–KBI7, RST, IRQ
RPU
30
45
60
kΩ
Low-voltage inhibit, trip falling voltage
VTRIPF
Low-voltage inhibit, trip rising voltage
VTRIPR
Low-voltage inhibit reset/recover hysteresis
VHYS
2.45
V
2.6
—
V
150
—
mV
Notes:
1. VDD = 3.0 to 3.6 Vdc, VSS = 0 Vdc, TA = TL to TH, unless otherwise noted.
2. Typical values reflect average measurements at midpoint of voltage range, 25 °C only.
3. Run (operating) IDD measured using external square wave clock source. All inputs 0.2 V from rail. No dc loads. Less than 100 pF
on all outputs. CL = 20 pF on OSC2. All ports configured as inputs. OSC2 capacitance linearly affects run IDD. Measured with all
modules enabled.
4. Wait IDD measured using external square wave clock source (fOSCXCLK = 24MHz); all inputs 0.2 V from rail; no dc loads; less than
100 pF on all outputs. CL = 20 pF on OSC2; USB in suspend mode, 15kΩ ± 5% termination resistors on D+ and D– pins; all ports
configured as inputs; OSC2 capacitance linearly affects wait IDD.
5. STOP IDD measured with USB in suspend mode, OSC1 grounded, 1.5kΩ ± 1% pull-up resistor on D+ pin and 15kΩ ± 1% pulldown resistors on D+ and D– pins, no port pins sourcing current.
6. Maximum is highest voltage that POR is guaranteed.
7. If minimum VDD is not reached before the internal POR reset is released, RST must be driven low externally until minimum VDD
is reached.
Data Sheet
346
MC68HC908LD64 — Rev. 3.0
Electrical Specifications
Freescale Semiconductor
Electrical Specifications
Control Timing
24.7 Control Timing
Table 24-5. Control Timing
Characteristic(1)
Symbol
Min
Max
Unit
Internal operating frequency(2)
fOP
—
6
MHz
RST input pulse width low(3)
tIRL
50
—
ns
Notes:
1. VDD = 3.0 to 3.6 Vdc, VSS = 0 Vdc; timing shown with respect to 20% VDD and 70% VDD, unless otherwise noted.
2. Some modules may require a minimum frequency greater than dc for proper operation;
see appropriate table for this information.
3. Minimum pulse width reset is guaranteed to be recognized. It is possible for a smaller pulse width to cause a reset.
24.8 TImer Interface Module Characteristics
Table 24-6. TIM Characteristics
Characteristic
Symbol
Min
Max
Unit
tTIH, tTIL
125
—
ns
tTCH, tTCL
(1/fOP) + 5
—
ns
Input capture pulse width
Input clock pulse width
24.9 Oscillator Characteristics
Table 24-7. Oscillator Characteristics
Characteristic
Symbol
Min
Typ
Max
Unit
Crystal frequency(1)
fOSCXCLK
—
24
—
MHz
External clock
Reference frequency(1), (2)
fOSCXCLK
dc
24
—
MHz
Crystal fixed capacitance(3)
C1
—
15
—
pF
Crystal tuning capacitance(3)
C2
—
15
—
pF
Feedback bias resistor
RB
—
2
—
MΩ
Series resistor(3)
RS
—
0
—
Ω
Notes:
1. The sync processor module is designed to function at fOSCXCLK = 24MHz.
2. No more than 10% duty cycle deviation from 50%
3. Not Required for high frequency crystals
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Electrical Specifications
347
Electrical Specifications
24.10 ADC Electrical Characteristics
Table 24-8. ADC Electrical Characteristics
Characteristic(1)
Symbol
Min
Max
Unit
Supply voltage
VDDAD
3.0
3.6
V
Input voltages
VADIN
0
VDD
V
Resolution
BAD
8
8
Bits
Absolute accuracy
AAD
±1
±2
LSB
Includes quantization
ADC internal clock
fADIC
0.5
1.048
MHz
tAIC = 1/fADIC,
tested only at 1 MHz
Conversion range
RAD
VSS
VDD
V
Power-up time
tADPU
16
Conversion time
tADC
16
17
tAIC
cycles
Sample time(2)
tADS
5
—
tAIC
cycles
Zero input reading(3)
ZADI
00
02
HEX
Full-scale reading(3)
FADI
FD
FF
HEX
Input capacitance
CADI
—
8
pF
—
—
±1
µA
Input leakage(4)
Port C
Comments
VDD ± 10%
tAIC
cycles
Not tested
Notes:
1. VDD = 3.0 to 3.6 Vdc, VSS = 0 Vdc, TA = TL to TH, unless otherwise noted.
2. Source impedances greater than 10 kΩ adversely affect internal RC charging time during input sampling.
3. Zero-input/full-scale reading requires sufficient decoupling measures for accurate conversions.
4. The external system error caused by input leakage current is approximately equal to the product of R source and input
current.
Data Sheet
348
MC68HC908LD64 — Rev. 3.0
Electrical Specifications
Freescale Semiconductor
Electrical Specifications
Sync Processor Timing
24.11 Sync Processor Timing
Table 24-9. Sync Processor Timing
Characteristic(1)
Symbol
Min
Max
Unit
VSYNC input sync pulse
tVI.SP
8
2048
µs
HSYNC input sync pulse
tHI.SP
0.1
6
µs
VSYNC to VSYNCO delay (8pF loading)
tVVd
30
40
µs
HSYNC to HSYNCO delay (8pF loading)
tHHd
30
40
µs
DE set-up time of DCLK
tDESu
4
—
µs
DE hold time of DCLK
tDEHd
4
—
µs
Notes:
1. VDD = 3.0 to 3.6 Vdc, VSS = 0 Vdc; timing shown with respect to 20% VDD and 70% VDD, unless otherwise noted.
24.12 USB DC Electrical Characteristics
Table 24-10. USB DC Electrical Characteristics
Characteristic(1)
Symbol
Conditions
Min
Hi-Z state data line leakage
ILO
0V<VIN <3.3V
–10
Differential input sensitivity
VDI
|(D+)–(D–)|
0.2
Differential common mode range
VCM
Includes VDI
range
0.8
2.5
V
Single ended receiver threshold
VSE
0.8
2.0
V
Static output low
VOL
RL of 1.5k to 3.6V
0.3
V
Static output high
VOH
RL of 15k to GND
3.6
V
2.8
Typ
Max
Unit
+10
µA
V
Notes:
1. VDD = 3.0 to 3.6 Vdc, VSS = 0 Vdc, TA = TL to TH, unless otherwise noted.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Electrical Specifications
349
Electrical Specifications
24.12.1 USB Low Speed Source Electrical Characteristics
Table 24-11. USB Low Speed Source Electrical Characteristics
Characteristic
Symbol
Internal operating frequency
fOP
Transition time(2)
Rise time
TR
Fall time
TF
Rise/Fall time matching
TRFM
Output signal crossover voltage
VCRS
Conditions(1)
Min
Typ
Max
6
CL=200pF
CL=600pF
CL=200pF
CL=600pF
75
TR/TF
80
MHz
300
ns
ns
ns
ns
120
%
2.0
V
1.5225
656.8
Mbs
ns
—
300
75
—
—
1.3
TDRATE
1.5Mbs ± 1.5%
1.4775
676.8
Source differential driver jitter
To next transition
For paired transitions
TUDJ1
TUDJ2
CL=350pF
Note (3), (4)
–25
–10
25
10
ns
ns
Receiver data jitter tolerance
To next transition
For paired transitions
TDJR1
TDJR2
CL=350pF
Notes (3), (4)
–75
–45
75
45
ns
ns
Source EOP width
TEOPT
Note (4)
1.25
1.50
µs
Differential to EOP transition skew
TDEOP
Note (4)
–40
100
ns
Receiver EOP width
Must reject as EOP
Must accept
TEOPR1
TEOPR2
Note (4)
330
675
Low speed data rate
1.500
666.0
Unit
ns
ns
Notes:
1. All voltages measured from local ground, unless otherwise specified. All timings use a capacitive load of 50pF, unless
otherwise specified. Low speed timings have a 1.5kΩ pull-up to 2.8V on the D– data line.
2. Transitions are measured from 10% to 90% of the data signal. The rising and falling edges should be smoothly transitioning
(monotonic). Capacitive loading includes 50pF of tester capacitance.
3. Timing differences between the differential data signals.
4. Measured at crossover point of differential data signals.
Data Sheet
350
MC68HC908LD64 — Rev. 3.0
Electrical Specifications
Freescale Semiconductor
Electrical Specifications
USB DC Electrical Characteristics
24.12.2 USB High Speed Source Electrical Characteristics
Table 24-12. USB High Speed Source Electrical Characteristics
Characteristic
Symbol
Conditions(1)
Min
Typ
Max
Unit
Internal operating frequency
fOP
Transition time(2)
Rise time
TR
CL=50pF
4
20
ns
TF
CL=50pF
4
20
ns
Rise/Fall time matching
TRFM
TR/TF
90
110
%
Output signal crossover voltage
VCRS
1.3
2.0
V
Fall time
6
MHz
High speed data rate
TDRATE
12Mbs ± 0.25%
11.97
12.03
Mbs
Frame interval
TFRAME
1.0ms ± 0.05%
0.9995
1.0005
ms
TDJ1
TDJ1
CL=50pF
Notes (3), (4)
–3.5
–4.0
3.5
4.0
ns
ns
Source EOP Width
TEOPT
Note (4)
160
175
ns
Differential to EOP transition skew
TDEOP
Note (4)
–2
5
ns
TJR1
TJR2
CL=50pF
Notes (3), (4)
–18.5
–9
18.5
9
ns
ns
TEOPR1
TEOPR2
Note (4)
40
82
Source differential driver jitter
To next transition
For paired transitions
Receive data jitter tolerance
To next transition
For paired transitions
Receiver EOP width
Must reject as EOP
Must accept
ns
ns
Notes:
1. All voltages measured from local ground, unless otherwise specified. All timings use a capacitive load of 50pF, unless
otherwise specified. High speed timings have a 1.5kΩ pull-up to 2.8V on the D+ data line.
2. Transitions are measured from 10% to 90% of the data signal. The rising and falling edges should be smoothly transitioning
(monotonic). Capacitive loading includes 50pF of tester capacitance.
3. Timing differences between the differential data signals.
4. Measured at crossover point of differential data signals.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Electrical Specifications
351
Electrical Specifications
24.12.3 HUB Repeater Electrical Characteristics
Table 24-13. HUB Repeater Electrical Characteristics
Low Speed HUB Electrical Characteristics (Root port and downstream ports configured as low speed)
Symbol
Conditions
Note(1),(2),(3)
HUB differential data delay
TLHDD
Note (4),(5),(6)
HUB differential driver jitter
(including cable)
Downstream:
To next transition
For paired transitions
Upstream
To next transition
For paired transitions
TLDHJ1
TLDHJ2
Note (4),(5),(6)
Characteristic
TLUHJ1
TLUHJ2
Min
Typ
Max
Unit
300
ns
–45
–15
45
15
ns
ns
45
45
45
45
ns
ns
TEOP
Note (4),(6)
–60
60
ns
HUB EOP delay relative to THDD
TLEOPD
Note (4),(6)
0
200
ns
HUB EOP output width skew
TLHESK
Note (4),(6)
–300
300
ns
Data bit width distortion after EOP.
Full Speed HUB Electrical Characteristics (Root port and downstream ports configured as full speed)
Characteristic
Symbol
Conditions
(Notes 1,2,3)
Min
Typ
Max
Unit
70
40
ns
ns
–3
–1
3
1
ns
ns
HUB differential data delay
(with cable)
(without cable)
THDD1
THDD1
HUB differential driver jitter
(including cable)
To next transition
For paired transitions
THDJ1
THDJ2
Data bit width distortion after SOP
TSOP
Note (3),(6)
–5
5
ns
HUB EOP delay relative to THDD
TEOPD
Note (3),(6)
0
15
ns
HUB EOP output width skew
THESK
Note (3),(6)
–15
15
ns
Note (3),(5),(6)
Note (3),(5),(6)
Notes:
1. All voltages measured from local ground, unless otherwise specified.
2. All timings use a capacitive load of (CL) to ground of 50pF, unless otherwise specified.
3. Full speed timings have a 1.5kΩ pull-up to 2.8V on the D+ data line.
4. Low speed timings have a 1.5kΩ pull-up to 2.8V on the D– data line.
5. Timing differences between the differential data signals.
6. Measured at crossover point of differential data signals.
Measured from 10% to 90% of the data signal.
The rising and falling edges should be smoothly transitioning (monotonic).
The maximum load specification is the maximum effective capacitive load allowed that meets the target HUB VBUS droop of 330mV.
Data Sheet
352
MC68HC908LD64 — Rev. 3.0
Electrical Specifications
Freescale Semiconductor
Electrical Specifications
USB DC Electrical Characteristics
24.12.4 USB Signaling Levels
Table 24-14. USB Signaling Levels
Signaling Levels
Bus State
From Originating Driver
At Receiver
Differential “1”
(D+) – (D–) > 200 mV and D+ or D– > VSE (min.)
Differential “0”
(D+) – (D–) < –200 mV and D+ or D– > VSE (min.)
Data J State:
Low Speed
Full Speed
Differential “0”
Differential “1”
Data K State:
Low Speed
Full Speed
Differential “1”
Differential “0”
Idle State:
Low Speed
Full Speed
Differential “0” and D– > VSE (max.) and D+ < VSE (min.)
Differential “1” and D+ > VSE (max.) and D– < VSE (min.)
Resume State:
Low Speed
Full Speed
Differential “1” and D+ > VSE (max.) and D– < VSE (min.)
Differential “0” and D– > VSE (max.) and D+ < VSE (min.)
Start of Packet (SOP)
Data lines switch from Idle to K State
End of Packet (EOP)
D+ and D– < VSE (min) for 2 bit
times(1) followed by an Idle for 1 bit
time
D+ and D– < VSE(min) for ≥ 1 bit
time(2) followed by a J State
Disconnect
(Upstream only)
—
D+ and D– < VSE(max) for ≥ 2.5 µs
Connect
(Upstream only)
—
D+ or D– > VSE(max) for ≥ 2.5 µs
Reset
(Downstream only)
D+ and D– < VSE for ≥10 ms
D+ and D– < VSE (min) for ≥ 2.5 µs
(must be recognized within 5.5
µs)(3)
Notes:
1. The width of EOP is defined in bit times relative to the speed of transmission.
2. The width of EOP is defined in bit times relative to the device type receiving the EOP.
3. These times apply to an active device that is not in the suspend state.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Electrical Specifications
353
Electrical Specifications
24.13 DDC12AB/MMIIC Timing
SDA
SCL
tHD.STA
tLOW
tHIGH
tSU.DAT
tHD.DAT
tSU.STA
tSU.STO
Figure 24-1. MMIIC Signal Timings
24.13.1 DDC12AB/MMIIC Interface Input Signal Timing
Table 24-15. DDC12AB/MMIIC Interface Input Signal Timing
Characteristic(1)
Symbol
Min
Max
Unit
tHD.STA
2
—
tCYC
Clock low period
tLOW
4
—
tCYC
Clock high period
tHIGH
4
—
tCYC
Data set-up time
tSU.DAT
250
—
ns
Data hold time
tHD.DAT
0
—
ns
START condition set-up time
(for repeated START condition only)
tSU.STA
2
—
tCYC
STOP condition set-up time
tSU.STO
2
—
tCYC
START condition hold time
Notes:
1. VDD = 3.0 to 3.6 Vdc, VSS = 0 Vdc; timing shown with respect to 20% VDD and 70% VDD, unless otherwise noted.
24.13.2 DDC12AB/MMIIC Interface Output Signal Timing
Table 24-16. DDC12AB/MMIIC Interface Output Signal Timing
Characteristic(1)
Symbol
Min
Max
Unit
SDA/SCL rise time(2)
tR
—
1
µs
SDA/SCL fall time
tF
—
300
ns
Data set-up time
tSU.DAT
tLOW
—
ns
Data hold time
tHD.DAT
0
—
ns
Notes:
1. VDD = 3.0 to 3.6 Vdc, VSS = 0 Vdc; timing shown with respect to 20% VDD and 70% VDD, unless otherwise noted.
2. With 200pF loading on the SDA/SCL pins.
Data Sheet
354
MC68HC908LD64 — Rev. 3.0
Electrical Specifications
Freescale Semiconductor
Electrical Specifications
FLASH Memory Characteristics
24.14 FLASH Memory Characteristics
Table 24-17. FLASH Memory Electrical Characteristics
Characteristic
Symbol
Min
Max
Unit
Program bus clock frequency
—
1
—
MHz
FLASH block size
$0C00–$0FFF
$1000–F9FF
—
—
128
512
Bytes
Bytes
FLASH programming size
—
64
Bytes
Read bus clock frequency
fRead(1)
32k
6M
Hz
Page erase time
tErase(2)
10
—
ms
Mass erase time
tMErase(3)
10
—
ms
PGM/ERASE to HVEN set up time
tnvs
5
—
µs
High-voltage hold time
tnvh
5
—
µs
High-voltage hold time (mass erase)
tnvhl
100
—
µs
Program hold time
tpgs
20
—
ns
Program time
tPROG
20
40
µs
Return to read time
trcv(4)
1
—
µs
Cumulative program HV period
4,7616 bytes array
13K-bytes array
tHV(5)
—
—
6
3
ms
ms
—
10k
—
Cycles
Row program endurance
—
10k
—
Cycles
Data retention time(9)
—
10
—
Years
Row erase endurance(7)
(8)
tHV1
(6)
Notes:
1. fREAD is defined as the frequency range for which the FLASH memory can be read.
2. If the page erase time is longer than tErase (Min), there is no erase-disturb, but it reduces the endurance of the FLASH
memory.
3. If the mass erase time is longer than tMErase (Min), there is no erase-disturb, but it reduces the endurance of the FLASH
memory.
4. trcv is defined as the time it needs before the FLASH can be read after turning off the high voltage charge pump, by clearing
HVEN to logic 0.
5. tHV is defined as the cumulative high voltage programming time to the same row before next erase.
tHV must satisfy this condition: tnvs + tnvh + tpgs + (tPROG × 64) ≤ tHV max.
6. tHV1 is the tHV spec for 13K-bytes array
7. The minimum row endurance value specifies each row of the FLASH memory is guaranteed to work for at least this many
erase / program cycles.
8. The minimum row endurance value specifies each row of the FLASH memory is guaranteed to work for at least this many
erase / program cycles.
9. The FLASH is guaranteed to retain data over the entire operating temperature range for at least the minimum time
specified.
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Electrical Specifications
355
Electrical Specifications
Data Sheet
356
MC68HC908LD64 — Rev. 3.0
Electrical Specifications
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 25. Mechanical Specifications
25.1 Contents
25.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357
25.3
64-Pin Plastic Quad Flat Pack (QFP) . . . . . . . . . . . . . . . . . . . 358
25.2 Introduction
This section gives the dimensions for:
•
64-pin plastic quad flat pack (case #840B)
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Mechanical Specifications
357
Mechanical Specifications
25.3 64-Pin Plastic Quad Flat Pack (QFP)
L
48
33
DETAIL A
S
D
S
H A–B
V
0.20 (0.008)
M
B
P
B
M
L
B
0.20 (0.008)
–B–
C A–B
–A–
0.05 (0.002) A–B
S
D
32
S
49
–A–, –B–, –D–
DETAIL A
64
17
F
1
16
–D–
A
0.20 (0.008)
C A–B
S
D
S
0.05 (0.002) A–B
S
0.20 (0.008) M H A–B
S
D
S
M
J
N
E
M
C
M
H
0.02 (0.008)
DATUM
PLANE
M
C A–B
S
D
S
SECTION B–B
0.01 (0.004)
G
U
T
R
–H–
DETAILC
–H–
–C–
SEATING
PLANE
BASE
METAL
D
DATUM
PLANE
Q
K
W
X
DETAIL C
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DATUM PLANE –H– IS LOCATED AT BOTTOM OF
LEAD AND IS COINCIDENT WITH THE LEAD
WHERE THE LEAD EXITS THE PLASTIC BODY AT
THE BOTTOM OF THE PARTING LINE.
4. DATUMS –A–, –B– AND –D– TO BE DETERMINED
AT DATUM PLANE –H–.
5. DIMENSIONS S AND V TO BE DETERMINED AT
SEATING PLANE –C–.
6. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE PROTRUSION IS 0.25
(0.010) PER SIDE. DIMENSIONS A AND B DO
INCLUDE MOLD MISMATCH AND ARE
DETERMINED AT DATUM PLANE –H–.
7. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 (0.003) PER SIDE.
TOTAL IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION. DAMBAR
CANNOT BE LOCATED ON THE LOWER RADIUS
OR THE FOOT.
DIM
A
B
C
D
E
F
G
H
J
K
L
M
N
P
Q
R
S
T
U
V
W
X
MILLIMETERS
MIN
MAX
13.90
14.10
13.90
14.10
2.15
2.45
0.30
0.45
2.00
2.40
0.30
0.40
0.80 BSC
—
0.25
0.13
0.23
0.65
0.95
12.00 REF
5°
10°
0.13
0.17
0.40 BSC
0°
7°
0.13
0.30
16.95
17.45
0.13
—
0°
—
16.95
17.45
0.35
0.45
1.6 REF
INCHES
MIN
MAX
0.547
0.555
0.547
0.555
0.085
0.096
0.012
0.018
0.079
0.094
0.012
0.016
0.031 BSC
—
0.010
0.005
0.009
0.026
0.037
0.472 REF
5°
10°
0.005
0.007
0.016 BSC
0°
7°
0.005
0.012
0.667
0.687
0.005
—
0°
—
0.667
0.687
0.014
0.018
0.063 REF
Figure 25-1. 64-Pin QFP (Case #840B)
Data Sheet
358
MC68HC908LD64 — Rev. 3.0
Mechanical Specifications
Freescale Semiconductor
Data Sheet — MC68HC908LD64
Section 26. Ordering Information
26.1 Contents
26.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359
26.3
MC Order Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359
26.2 Introduction
This section contains ordering numbers for the MC68HC908LD64.
26.3 MC Order Numbers
Table 26-1. MC Order Numbers
MC Order Number(1)
MC68HC908LD64IFU
Package
Operating
Temperature Range
64-Pin QFP
0 °C to +85 °C
Notes:
1. I = Operating temperature range: 0 °C to +85 °C
FU = Quad Flat Pack
MC68HC908LD64 — Rev. 3.0
Freescale Semiconductor
Data Sheet
Ordering Information
359
Ordering Information
Data Sheet
360
MC68HC908LD64 — Rev. 3.0
Ordering Information
Freescale Semiconductor
How to Reach Us:
USA/Europe/Locations Not Listed:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-521-6274 or 480-768-2130
Japan:
Freescale Semiconductor Japan Ltd.
Technical Information Center
3-20-1, Minami-Azabu, Minato-ku
Tokyo 106-8573, Japan
81-3-3440-3569
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
852-26668334
Home Page:
www.freescale.com
RoHS-compliant and/or Pb- free versions of Freescale products have the functionality
and electrical characteristics of their non-RoHS-compliant and/or non-Pb- free
counterparts. For further information, see http://www.freescale.com or contact your
Freescale sales representative.
For information on Freescale.s Environmental Products program, go to
http://www.freescale.com/epp.
Information in this document is provided solely to enable system and software implementers to use Freescale
Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any
integrated circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale
Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or
circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages.
“Typical” parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary
in different applications and actual performance may vary over time. All operating parameters, including “Typicals”, must
be validated for each customer application by customer’s technical experts. Freescale Semiconductor does not convey any
license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or
authorized for use as components in systems intended for surgical implant into the body, or other applications intended to
support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create
a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for
any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers,
employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and
reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the
design or manufacture of the part.
Learn More: For more information about Freescale products, please visit www.freescale.com
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names
are the property of their respective owners.
© Freescale Semiconductor, Inc. 2004
MC68HC908LD64
Rev. 3
07/2004