MIC2203 High Efficiency 1MHz Synchronous Buck Regulator General Description Features The Micrel MIC2203 is a high efficiency 1MHz PWM synchronous buck switching regulator. The MIC2203 features low noise constant frequency PWM operation with a low dynamic supply current of <1mA. The low noise and efficient operation both make the MIC2203 well suited for sensitive RF, and audio power applications. The MIC2203 operates from 2.3V to 5.5V input and can supply over 300mA of output current with output voltages down to 0.5V. Additionally, the MIC2203 can be synchronized to an external clock, or multiple MIC2203s can easily be daisy-chained with the SYNCLOCK feature. The MIC2203 has a high loop bandwidth with corresponding ultra fast transient response times. This reduces the output capacitor size, and is very useful when powering applications that require fast dynamic response such as CPU cores and RF circuitry in high performance cellular phones and PDAs. The MIC2203 is available in 10-pin MSOP and 3mm x 3mm MLF™-10L package options with an operating junction temperature range from –40ºC to 125ºC. • • • • • • • • • • • Input voltage range: 2.3V to 5.5V Output voltage adjustable down to 0.5V 300mA output current Constant 1MHz PWM switching frequency > 95% efficiency < 1mA switching supply current < 350µA static quiescent current < 1µA shutdown current All-ceramic capacitors Easily synchronized to external clock SYNCLOCK feature to daisy chain multiple devices • Thermal shutdown and current limit protection • 10 pin MSOP, and 3mm x 3mm MLF-10L package options • –40ºC to +125ºC junction temperature range Applications • 802.11 WLAN modules • MD players • MP3 players _____________________________________________________________________ Typical Application 10µH 1.8V 300mA MIC2203BMM 2.3V to 5.5V SYNC_IN 1µF SYNC_OUT EN 1 10 2 9 3 8 4 7 5 6 R1 10k 2.2µF 10nF R2 3.83k High Efficiency Buck Regulator MicroLead Frame and MLF are trademarks of Amkor Technologies. Micrel, Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax +1 (408) 474-1000 • http://www.micrel.com December 2004 M9999-120604 (408) 955-1690 Micrel, Inc. MIC2203 Ordering Information Part Number Standard Pb-Free MIC2203BMM MIC2203YMM MIC2203BML MIC2203YML Output Voltage Junction Temperature Range Package Adjustable Adjustable -40°C to +125°C -40°C to +125°C MSOP-10L 3mm x 3mm MLF-10L Pin Configuration MLF-10 (ML) Top View MSOP-10 (MM) Pin Description Pin Number Pin Name 1 SW Switch (Output): Internal power MOSFET output switches. Pin Function 2 VIN Supply Voltage (Input): Requires a bypass capacitor to GND. 3 SYNC_IN 4 SYNC_OUT 5 EN A low level EN will power down the device, reducing the quiescent current to under 1µA. 6 FB Input to the error amplifier, connect to the external resistor divider network to set the output voltage. 7 BIAS Internal circuit bias supply, nominally 2.3V. Must be de-coupled to signal ground and can have a minimum of external DC loading. 8,9,10 GND Ground EP GND Exposed backside pad, connect to Ground (MLF option only) SYNC_IN for the MIC2203, Sync the main switching frequency to a external clock. Should be tied to ground when not in use. SYNC_OUT a 50ns wide sync pulse to feed into SYNC_IN on MIC2203. Can be left open or tied to ground when not used. December 2004 2 M9999-120604 (408) 955-1690 Micrel, Inc. MIC2203 Absolute Maximum Ratings(1) Operating Ratings(2) Supply Voltage (VIN) .............................................. 6V Output Switch Voltage (VSW) ................................. 6V Logic Input Voltage (VEN, VSYNC_IN) .............VIN to –3V Power Dissipation ............................................Note 5 Storage Temperature (Ts)............... –65°C to +150°C ESD Rating(3) ........................................................2kV Supply Voltage (VIN)................................2.3V to 5.5V Junction Temperature Range ......... –40°C to +125°C Package Thermal Resistance MSOP-10L (θJA)..................................... 115°C/W 3mmX3mm MLF-10L (θJA)....................... 60°C/W Electrical Characteristics(4) TA = 25°C with VIN = VEN = 3.5V, unless otherwise specified. Bold values indicate –40ºC < TJ < +125ºC Parameter Condition Min 2.3 Supply Voltage Range Quiescent Current No Load Supply Current Typ Max Units 5.5 V VFB = 0.6V (not switching) 320 450 µA EN = 0V (shutdown) 0.01 1 µA (switching) 870 MIC2203 [Adjustable] Feedback Voltage 0.4875 µA 0.5 0.5125 V Output Voltage Line Regulation VOUT < 2V; VIN = 2.3V to 5.5V, ILOAD= 50mA 0.13 0.5 % Output Voltage Load Regulation 0mA < ILOAD < 300mA 0.2 0.5 % 2.32 2.6 V Bias Regulator Output Voltage 2.2 Maximum Duty Cycle VFB ≤ 0.4V 100 Current Limit VFB = 0.4V 0.375 Switch ON-Resistance ISW = 300mA VFB = 0.4V ISW = -300mA VFB = 0.6V Enable Input Current Sync Frequency Range 0.8 SYNC_IN Threshold 0.7 Sync Minimum Pulse Width % 0.6 1.5 A 1.5 1 2.2 1.6 Ω 0.01 2 µA 1.25 MHz 1 1.7 10 SYNC_IN Input Current V ns 1 µA Oscillator Frequency 0.8 1 1.2 MHz Enable Threshold 0.5 0.7 1.3 V Enable Hysteresis Over Temperature Shutdown Hysteresis 20 mV 160 20 °C Notes: 1. Exceeding the absolute maximum rating may damage the device. 2. The device is not guaranteed to function outside its operating rating. 3. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5k in series with 100pF. 4. Specification for packaged product only. 5. Absolute maximum power dissipation is limited by maximum junction temperature where PD(MAX) = (TJ(MAX) – TA) ÷θJA. December 2004 3 M9999-120604 (408) 955-1690 Micrel, Inc. MIC2203 Typical Characteristics December 2004 4 M9999-120604 (408) 955-1690 Micrel, Inc. MIC2203 Functional Diagram VIN CIN SYNC_OUT Oscillator Ramp Generator SYNC_IN BIAS VIN Internal Supply R1 PWM Comparator Error Amplifier Driver VOUT SW R2 COUT 0.5V EN MIC2203 FB GND Figure 1. MIC2203 Block Diagram December 2004 5 M9999-120604 (408) 955-1690 Micrel, Inc. MIC2203 Functional Description SYNC_OUT SYNC_OUT is an open collector output that provides a signal equal to the internal oscillator frequency. This creates the ability for multiple MIC2203s to be connected together in a masterslave configuration for frequency matching of the converters. A typical 10kΩ resistor is recommended for the pull-up resistor. VIN VIN provides power to the output and to the internal bias supply. The supply voltage range is from 2.3V to 5.5V. A minimum 1µF ceramic capacitor is recommended for bypassing the input supply. Enable The enable pin provides a logic level control of the output. In the off state, supply current of the device is greatly reduced (typically <1µA). Also, in the off state, the output drive is placed in a “tri-stated” condition, where both the high side P-Channel MOSFET and the low-side N-Channel are in an off or non-conducting state. Do not drive the enable pin above the supply voltage. Bias The bias supply is an internal 2.3V linear regulator that supplies the internal biasing voltage to the MIC2203. A 10nF ceramic capacitor is required on this pin for bypassing. Do not use the bias pin as a supply. The bias pin was designed to supply internal power only. Feedback The feedback pin provides the control path to control the output. A resistor divider connecting the feedback to the output is used to adjust the desired output voltage. Refer to the feedback section in the “Applications Information” for more detail. SYNC_IN SYNC_IN pin enables the ability to change the fundamental switching frequency. The SYNC_IN frequency has a minimum frequency of 800KHz and a maximum sync frequency of 1.2MHz. Careful attention should be paid to not driving the SYNC_IN pin greater than the supply voltage. Although this will not damage the device, it can cause improper operation. December 2004 6 M9999-120604 (408) 955-1690 Micrel, Inc. MIC2203 Application Information Bias Capacitor Input Capacitor A small 10nF ceramic capacitor is required to bypass the bias pin. The use of low ESR ceramics provides improved filtering for the bias supply. Efficiency Considerations Efficiency is defined as the amount of useful output power, divided by the amount of power consumed. ⎛V ×I ⎞ Efficiency% = ⎜ OUT OUT ⎟ × 100 ⎝ VIN × IIN ⎠ A minimum 1µF ceramic capacitor is recommended on the VIN pin for bypassing. X5R or X7R dielectrics are recommended for the input capacitor. Y5V dielectrics, aside from losing most of their capacitance over temperature, also become resistive at high frequencies. This reduces their ability to filter out high frequency noise. Output Capacitor The MIC2203 was designed specifically for the use of a 2.2µF ceramic output capacitor. Since the MIC2203 is voltage mode regulator, the control loop relies on the inductor and output capacitor for compensation. For this reason, do not use excessively large output capacitors. The output capacitor requires either an X7R or X5R dielectric. Y5V and Z5U dielectric capacitors, aside from the undesirable effect of their wide variation in capacitance over temperature, become resistive at high frequencies. Using Y5V or Z5U capacitors will cause instability in the MIC2203. Maintaining high efficiency serves two purposes. It reduces power dissipation in the power supply, reducing the need for heat sinks and thermal design considerations, and it reduces consumption of current for battery powered applications. Reduced current drawn from a battery increases the device’s operating time, which is critical in hand held devices. There are two loss terms in switching converters: DC losses and switching losses. DC losses are simply 2 the power dissipation of I R. Power is dissipated in the high side switch during the on cycle. Power loss is equal to the high side MOSFET RDS(ON) multiplied 2 by the (Switch Current) . During the off cycle, the low side N-Channel MOSFET conducts, also dissipating power. Device operating current also reduces efficiency. The product of the quiescent (operating) current and the supply voltage is another DC loss. The current required to drive the gates on and off at a constant 1MHz frequency and the switching transitions make up the switching losses. Figure 2 shows an efficiency curve. The non-shaded portion, from 0mA to 100mA, efficiency losses are dominated by quiescent current losses, gate drive and transition losses. In this case, lower supply voltages yield greater efficiency in that they require less current to drive the MOSFETs and have reduced input power consumption. Total output capacitance should not exceed 3µF. Inductor Selection Inductor selection will be determined by the following (not necessarily in the order of importance): • Inductance • Rated current value • Size requirements • DC resistance (DCR) The MIC2203 is designed for use with a 10µH inductor. Maximum current ratings of the inductor are generally given in two methods: permissible DC current and saturation current. Permissible DC current can be rated either for a 40°C temperature rise or a 10% loss in inductance. Ensure the inductor selected can handle the maximum operating current. When saturation current is specified, make sure that there is enough margin that the peak current will not saturate the inductor. The size requirements refer to the area and height requirements that are necessary to fit a particular design. Please refer to the inductor dimensions on their datasheet. DC resistance is also important. While DCR is inversely proportional to size, DCR can represent a significant efficiency loss. Refer to the “Efficiency Considerations” below for a more detailed description. December 2004 Figure 2. Efficiency Curve The shaded region, 100mA to 300mA, efficiency loss is dominated by MOSFET RDS(ON) and inductor DC losses. Higher input supply voltages will increase 7 M9999-120604 (408) 955-1690 Micrel, Inc. MIC2203 the Gate-to-Source threshold on the internal MOSFETs, reducing the internal RDS(ON). This improves efficiency by reducing DC losses in the device. All but the inductor losses are inherent to the device. In which case, inductor selection becomes increasingly critical in efficiency calculations. As the inductors are reduced in size, the DC resistance (DCR) can become quite significant. The DCR losses can be calculated as follows: can create a phase loss at high frequency. This phase loss degrades transient response by reducing phase margin. Adding feed-forward capacitance negates the parasitic capacitive effects of the feedback pin. Also, large feedback resistor values increase the impedance, making the feedback node more susceptible to noise pick-up. A feed-forward capacitor would also reduce noise pick-up by providing a low impedance path to the output. PL = IOUT 2 × DCR PWM Operation The MIC2203 is a pulse width modulation (PWM) regulator. By controlling the ratio of on-to-off time, or duty cycle, a regulated DC output voltage is achieved. As load or supply voltage changes, so does the duty cycle to maintain a constant output voltage. In cases where the input supply runs into a dropout condition, the MIC2203 will run at 100% duty cycle. The MIC2203 provides constant switching at 1MHz with synchronous internal MOSFETs. The internal MOSFETs include a high-side P-Channel MOSFET from the input supply to the switch pin and an NChannel MOSFET from the switch pin-to-ground. Since the low-side N-Channel MOSFET provides the current during the off cycle, a free wheeling Schottky diode from the switch node to ground is not required. PWM control provides fixed frequency operation. By maintaining a constant switching frequency, predictable fundamental and harmonic frequencies are achieved. Other methods of regulation, such as burst and skip modes, have frequency spectrums that change with load that can interfere with sensitive communication equipment. From that, the loss in efficiency due to inductor resistance can be calculated as follows: ⎡ ⎛ V ×I ⎞⎤ OUT OUT Efficiency Loss = ⎢-1 ⎜ ⎟⎥ × 100 ⎣ ⎝ VOUT × IOUT × PL ⎠⎦ Efficiency loss, due to DCR, is minimal at light loads and gains significance as the load is increased. Inductor selection becomes a trade-off between efficiency and size in this case. Compensation The MIC2203 is an internally compensated, voltage mode buck regulator. Voltage mode is achieved by creating an internal 1MHz ramp signal and using the output of the error amplifier to pulse width modulate the switch node, maintaining output voltage regulation. With a typical gain bandwidth of 100kHz, the MIC2203 is capable of extremely fast transient responses. The MIC2203 is designed to be stable with a 10µH inductor and a 2.2µF ceramic (X5R) output capacitor. Feedback The MIC2203 provides a feedback pin to adjust the output voltage to the desired level. This pin connects internally to an error amplifier. The error amplifier then compares the voltage at the feedback to the internal 0.5V reference voltage and adjusts the output voltage to maintain regulation. To calculate the resistor divider network for the desired output is as follows: R1 R2 = ⎛V ⎞ ⎜ OUT −1⎟ ⎝ VREF ⎠ Synchronization SYNC_IN allows the user to change the frequency from 1MHz up to 1.25MHz or down to 800KHz. This allows the ability to control the fundamental frequency and all the resultant harmonics. Maintaining a predictable frequency creates the ability to either shift the harmonics away from sensitive carrier and IF frequency bands or to accurately filter out specific harmonic frequencies. The SYNC_OUT function pin allows for the ability to be able to sync up multiple MIC2203s in a “daisychain”, connecting SYNC_OUT to SYNC_IN of the other MIC2203. Synchronizing multiple MIC2203s benefits much in the same way as syncing up one MIC2203. All regulators will run at the same fundamental frequency, resulting in matched harmonic frequencies, simplifying design for sensitive communication equipment. Where VREF is 0.5V and VOUT is the desired output voltage. A 10kΩ or lower resistor value from the output to the feedback is recommended. Larger resistor values require an additional capacitor (feedforward) from the output to the feedback. The large high side resistor value and the parasitic capacitance on the feedback pin (~10pF) can cause an additional pole in the loop. The additional pole December 2004 8 M9999-120604 (408) 955-1690 Micrel, Inc. MIC2203 Figure 1. Master-Slave Operation December 2004 9 M9999-120604 (408) 955-1690 Micrel, Inc. MIC2203 MIC2203 with 10µH Inductor and 2.2µF Output Capacitor December 2004 10 M9999-120604 (408) 955-1690 Micrel, Inc. December 2004 MIC2203 11 M9999-120604 (408) 955-1690 Micrel, Inc. MIC2203 MIC2203BMM Evaluation Board Schematic Figure 2. MIC2203BMM Evaluation Board Schematic Bill of Materials Item Part Number Manufacturer Description C1 06036D105MAT AVX 1µF Ceramic Capacitor X5R, 6.3V, Size 0603 GRM185R60J105KE21D Murata 1µF Ceramic Capacitor X5R, 6.3V, Size 0603 0201ZD103MAT2 AVX 10nF Ceramic Capacitor 6.3V, Size 0201 C2 GRM033R10J103KA01D Murata 10nF Ceramic Capacitor 6.3V, Size 0202 06036D225MAT AVX 2.2µF Ceramic Capacitor X5R, 6.3V, Size 0603 GRM185R60J22SKE21D Murata 2.2µF Ceramic Capacitor X5R, 6.3V, Size 0603 LQH32CN100M Murata 10µH Inductor CDRH2D14-10 Sumida 10µH Inductor R1 CRCW04021002F Vishay-Dale 10kΩ 1%, Size 0402 R2 CRCW04021781F CRCW04022491F CRCW04023831F CRCW04024991F CRCW04027151F CRCW04021002F NA Vishay-Dale Vishay-Dale Vishay-Dale Vishay-Dale Vishay-Dale Vishay-Dale 1.78kΩ 1%, Size 0402 For 3.3VOUT 2.49kΩ 1%, Size 0402 For 2.5VOUT 3.83kΩ 1%, Size 0402 For 1.8VOUT 4.99kΩ 1%, Size 0402 For 1.5VOUT 7.15kΩ 1%, Size 0402 For 1.2VOUT 10kΩ 1%, Size 0402 For 1VOUT Open For 0.5VOUT U1 MIC2203BMM Micrel, Inc. 1MHz High Efficiency Synchronous Buck Regulator C3 L1 Notes: 1. 2. 3. 4. 5. AVX: www.avx.com Murata: www.murata.com Sumida: www.sumida.com Vishay-Dale: www.vishay.com Micrel, Inc: www.micrel.com December 2004 12 M9999-120604 (408) 955-1690 Micrel, Inc. MIC2203 Package Information 10-Pin MSOP (MM) 10-Pin MLF™ (ML) MICREL, INC. 2180 Fortune DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http:/www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2004 Micrel, Incorporated. December 2004 13 M9999-120604 (408) 955-1690