MKT 1813 Vishay Roederstein DC Film Capacitor MKT Axial Type FEATURES Supplied loose in box, taped on ammopack or reel RoHS compliant Ød L Max. 40.0 ± 5.0 D Max. 40.0 ± 5.0 Dimensions in mm LEAD DIAMETER d (mm) D (mm) 0.6 ≤ 5.0 0.7 > 5.0 ≤ 7.0 0.8 > 7.0 < 16.5 1.0 ≥ 16.5 ENCAPSULATION Plastic-wrapped, retardant epoxy resin sealed, flame CLIMATIC TESTING CLASS ACC. TO IEC 60068-1 55/100/56 CAPACITANCE RANGE (E12 SERIES) 470 pF to 22 µF MAIN APPLICATIONS CAPACITANCE TOLERANCE Blocking, bypassing, filtering, timing, coupling and decoupling, interference suppression in low voltage applications ± 20 %, ± 10 %, ± 5 % LEADS Tinned wire REFERENCE STANDARDS IEC 60384-2 MAXIMUM APPLICATION TEMPERATURE 100 °C MARKING C-value; tolerance; rated voltage; manufacturer’s type; code for dielectric material; manufacturer location; manufacturer’s logo; year and week PULL TEST ON LEADS Minimum 20 N in direction of leads according to IEC 60068-2-21 DIELECTRIC BENT TEST ON LEADS Polyester film 2 bends trough 90° combined with 10 N tensile strength ELECTRODES RELIABILITY Metallized Operational life > 300 000 h (40 °C/0.5 UR) Failure rate < 2 FIT (40 °C/0.5 UR) CONSTRUCTION Mono and internal series construction DETAIL SPECIFICATION RATED (DC) VOLTAGE 63 V, 100 V, 250 V, 400 V, 630 V, 1000 V For more detailed data and test requirements contact: [email protected] RATED (AC) VOLTAGE 40 V, 63 V, 160 V, 200 V, 220 V Document Number: 26013 Revision: 08-Dec-08 For technical questions, contact: [email protected] www.vishay.com 17 MKT 1813 DC Film Capacitor MKT Axial Type Vishay Roederstein COMPOSITION OF CATALOG NUMBER CAPACITANCE (numerically) MULTIPLIER (nF) 0.1 2 1 3 10 4 100 5 MKT 1813 X Example: 468 = 680 nF XX 25 X X SPECIAL LETTER FOR TAPED Bulk TYPE TOLERANCE Un = 06 = 63 V 4 ±5% Un = 01 = 100 V 5 ± 10 % Un = 25 = 250 V 6 ± 20 % R Reel G Ammopack Un = 40 = 400 V Un = 63 = 630 V Un = 10 = 1000 V Note For detailed tape specifications refer to “Packaging Information” www.vishay.com/doc?28139 or end of catalog SPECIFIC REFERENCE DATA DESCRIPTION VALUE Tangent of loss angle: at 1 kHz at 10 kHz at 100 kHz C = 0.1 µF 80 x 10-4 150 x 10-4 250 x 10-4 10-4 10-4 0.1 µF ≤ C = 1.0 µF 80 x C ≥ 1.0 µF 100 x 10-4 Maximum pulse rise time (dU/dt)R [V/µs] 150 x - - Capacitor length (mm) 63 Vdc 100 Vdc 250 Vdc 400 Vdc 630 Vdc 11 12 18 32 56 84 - 14 11 13 22 37 66 175 1000 Vdc 19 7 8 13 21 33 65 26.5 4 5 8 13 19 34 31.5 3 4 6 10 15 25 41.5 2 3 5 7 10 17 If the maximum pulse voltage is less than the rated voltage higher dU/dt values can be permitted. R between leads, for C ≤ 0.33 µF and UR ≤ 100 V > 15 000 MΩ R between leads, for C ≤ 0.33 µF and UR > 100 V > 30 000 MΩ RC between leads, for C > 0.33 µF and UR ≤ 100 V > 5000 s RC between leads, for C > 0.33 µF and UR > 100 V > 10 000 s R between leads and case, 100 V; (foil method) Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s Maximum application temperature www.vishay.com 18 > 30 000 MΩ 1.6 x URdc, 1 min 100 °C For technical questions, contact: [email protected] Document Number: 26013 Revision: 08-Dec-08 MKT 1813 DC Film Capacitor MKT Axial Type Vishay Roederstein VOLTAGE CODE 06 63 Vdc/ 40 Vac VOLTAGE CODE 01 100 Vdc/ 63 Vac VOLTAGE CODE 25 250 Vdc/ 160 Vac VOLTAGE CODE 40 400 Vdc/ 200 Vac VOLTAGE CODE 63 (1) 630 Vdc/ 220 Vac VOLTAGE CODE 10 (1) 1000 Vdc/ 220 Vac CAPACITANCE CAPACITANCE CODE D L D L D L D L D L D L 470 pF 147 - - - - - - - - 5.0 11.0 - - 680 pF 168 - - - - - - - - 5.0 11.0 - - 1000 pF 210 - - - - - - - - 5.0 11.0 5.5 14.0 1500 pF 215 - - - - - - - - 5.0 11.0 6.0 14.0 2200 pF 222 - - - - - - - - 5.0 11.0 6.0 14.0 3300 pF 233 - - - - - - - - 5.0 11.0 7.0 14.0 4700 pF 247 - - - - - - - - 5.0 11.0 6.0 19.0 6800 pF 268 - - - - - - 5.0 11.0 6.0 14.0 6.0 19.0 0.01 µF 310 - - - - - - 5.0 11.0 6.0 14.0 6.5 19.0 0.015 µF 315 - - - - 5.0 11.0 6.0 14.0 6.5 14.0 7.5 19.0 0.022 µF 322 - - - - 5.0 11.0 6.0 14.0 7.5 14.0 9.0 19.0 0.033 µF 333 - - - - 5.0 11.0 6.0 14.0 6.5 19.0 10.5 19.0 0.047 µF 347 - - - - 6.0 14.0 7.0 14.0 7.5 19.0 12.0 19.0 0.068 µF 368 - - 5.0 11.0 6.0 14.0 8.0 14.0 8.5 19.0 11.0 26.5 - - 5.0 11.0 6.0 14.0 7.0 19.0 10.5 19.0 13.0 26.5 0.1 µF 410 0.15 µF 415 0.22 µF 422 0.33 µF 433 0.47 µF 447 0.68 µF 468 1.0 µF 510 1.5 µF 2.2 µF 3.3 µF 515 522 533 4.7 µF 547 6.8 µF 568 - - - - - - - - 9.5 19.0 (2) - - 5.0 11.0 5.5 11.0 7.0 14.0 8.5 19.0 10.0 26.5 13.5 31.5 5.0 11.0 6.0 14.0 7.0 19.0 8.0 26.5 11.5 26.5 16.0 31.5 - - - - - - 8.0 19.0 (2) - - - - 6.0 14.0 6.0 19.0 8.0 19.0 9.5 26.5 13.5 26.5 16.0 41.5 - - - - - - 9.5 19.0 (2) - - - - 7.0 14.0 6.5 19.0 9.0 19.0 11.0 26.5 14.5 31.5 19.0 41.5 - - - - - - - - 14.0 26.5 (2) - - 6.5 19.0 7.0 19.0 8.5 26.5 11.5 31.5 14.5 41.5 - - - - - - 9.0 19.0 (2) - - - - - - 7.5 19.0 8.5 19.0 10.0 26.5 13.5 31.5 16.5 41.5 - - 8.5 19.0 8.0 26.5 11.0 31.5 14.0 41.5 - - - - - - 8.0 19.0 (2) - - 13.0 31.5 (2) - - - - 8.5 26.5 9.5 26.5 13.0 31.5 16.5 41.5 - - - - 7.5 19.0 (2) 9.5 19.0 (2) - - - - - - - - 10.0 26.5 11.5 26.5 15.5 31.5 - - - - - - 8.5 19.0 (2) - - 14.0 26.5 (2) - - - - - - 11.5 26.5 12.0 31.5 15.5 41.5 - - - - - - - - - - 14.5 31.5 (2) - - - - - - 12.0 31.5 14.0 31.5 17.5 41.5 - - - - - - 14.5 31.5 16.5 31.5 21.0 41.5 - - - - - - 10.0 µF 610 - - 13.5 31.5 (2) - - - - - - - - 15.0 µF 615 18.0 31.5 20.5 31.5 - - - - - - - - 22.0 µF 622 17.5 41.5 - - - - - - - - - - Notes • Pitch = L + 3.5 (1) Not suitable for mains applications (2) For the smaller size please add “-M” at the end of the type designation (e.g. MKT 1813-510/255-M) Document Number: 26013 Revision: 08-Dec-08 For technical questions, contact: [email protected] www.vishay.com 19 MKT 1813 DC Film Capacitor MKT Axial Type Vishay Roederstein RECOMMENDED PACKAGING PACKAGING CODE TYPE OF PACKAGING REEL DIAMETER (mm) ORDERING CODE EXAMPLES G R - Ammo Reel Bulk 350 - MKT 1813-422-014-G MKT 1813-422-014-R MKT 1813-422-014 x x x Note • Attention: Capacitors with L > 31.5 mm only as bulk available EXAMPLE OF ORDERING CODE TYPE CAPACITANCE CODE VOLTAGE CODE MKT 1813 410 Note (1) Tolerance Codes: 4 = 5 % (J); 5 = 10 % (K); 6 = 20 % (M) TOLERANCE CODE (1) PACKAGING CODE 5 G 06 MOUNTING Normal Use The capacitors are designed for mounting on printed-circuit boards. The capacitors packed in bandoliers are designed for mounting in printed-circuit boards by means of automatic insertion machines. For detailed tape specifications refer to Packaging information: www.vishay.com/doc?28139 or end of catalog. Specific Method of Mounting to Withstand Vibration and Shock In order to withstand vibration and shock tests, it must be ensured that the capacitor body is in good contact with the printed-circuit board: • For L ≤ 19 mm capacitors shall be mechanically fixed by the leads • For larger pitches the capacitors shall be mounted in the same way and the body clamped • The maximum diameter and length of the capacitors are specified in the dimensions table • Eccentricity as shown in the drawing below Space Requirements On Printed-Circuit Board The maximum length and width of film capacitors is shown in the drawing: • Eccentricity as in drawing. The maximum eccentricity is smaller than or equal to the lead diameter of the product concerned. • Product height with seating plane as given by “IEC 60717” as reference: hmax. ≤ h + 0.4 mm or hmax. ≤ h' + 0.4 mm 1 mm Storage Temperature • Storage temperature: Tstg = - 25 °C to + 40 °C with RH maximum 80 % without condensation Ratings and Characteristics Reference Conditions Unless otherwise specified, all electrical values apply to an ambient temperature of 23 ± 1 °C, an atmospheric pressure of 86 kPa to 106 kPa and a relative humidity of 50 ± 2 %. For reference testing, a conditioning period shall be applied over 96 ± 4 h by heating the products in a circulating air oven at the rated temperature and a relative humidity not exceeding 20 %. www.vishay.com 20 For technical questions, contact: [email protected] Document Number: 26013 Revision: 08-Dec-08 MKT 1813 DC Film Capacitor MKT Axial Type Vishay Roederstein CHARACTERISTICS 1000 Capacitance in µF 7 5 VRMS VRMS 100 0. 15 3 3 0. 2 2 33 0. 47 10 22 7 5 15 Capacitance in µF 7 5 100 1. 0 10 0.0 06 8 4. 7 0.0 22 7 5 2. 2 3 3 2 2 2.2 1 .0 63 Vdc 2 3 3 5 7 10 2 4 3 5 7 10 2 3 5 7 10 f [Hz] Permissible AC Voltage vs. Frequency 0.0 3 68 0.1 3 5 7 103 2 5 7 104 3 2 5 7 105 f [Hz] 3 0.2 2 2 0.4 10 7 5 100 7 3 2 5 7 103 2 3 5 7 104 2 3 Permissible AC Voltage vs. Frequency 0 0. 00 22 03 3 0. 00 1 0. 1 3 0. 22 1. 0 2 15 100 Vdc 47 0. 00 47 0. 7 5 4.7 3 0. 01 1.0 2.2 2 Capacitance in pF and µF 7 5 3 5 2 630 Vdc 5 7 105 f [Hz] 1000 VRMS 2 Permissible AC Voltage vs. Frequency VRMS VRMS Capacitance in µF 7 5 10 102 2 3 5 7 103 2 3 5 7 104 2 3 Permissible AC Voltage vs. Frequency 5 7 105 f [Hz] 1000 Capacitance in µF 7 5 3 Capacitance in pF and µF 7 5 3 2 2 0. 100 7 5 10 4. 7 2. 2 1.0 2 5 0. 33 3 0. 1 100 04 7 0. 0. 0. 7 5 15 20 04 22 7 0. 00 02 2 0. 01 0. 47 3 47 00 2 1000 Vdc 250 Vdc 2 10 00 01 0. 3 10 102 0.1 1000 100 1 102 10 102 5 VRMS 10 47 7 0.2 2 400 Vdc 1 2 0.0 0.4 5 7 103 2 Permissible AC Voltage vs. Frequency Document Number: 26013 Revision: 08-Dec-08 3 5 7 104 2 3 5 7 105 f [Hz] 10 102 2 3 5 7 103 2 Permissible AC Voltage vs. Frequency For technical questions, contact: [email protected] 3 5 7 104 2 3 5 7 105 f [Hz] www.vishay.com 21 MKT 1813 DC Film Capacitor MKT Axial Type Vishay Roederstein Nominal voltage (AC and DC) as a function of temperature U = f(TA), TLL ≤ TA ≤ TUL 1.2 Capacitance as a function of temperature ΔC/C = f(TA), TLL ≤ TA ≤ TUL factor ΔC = (%) C 12 10 1.0 8 6 0.8 4 0.6 2 0 0.4 -2 -4 0.2 -6 0.0 - 60 - 20 20 60 Tamb (°C) 100 -8 - 60 - 40 - 20 0 20 40 60 80 100 120 Capacitance vs. Temperature ΔC/C = f (ϑ) Dissipation factor as function of temperature Δtan δ/tan δ = f(TA), TLL ≤ TA ≤ TUL Capacitance as function of frequency ΔC/C = f(f), 100 Hz ≤ f ≤ 1 MHz tan δ = 10-3 ΔC = (%) C 2 1 16 14 12 0 -1 10 -2 8 -3 6 -4 4 -5 2 -6 140 Tamb (°C) 102 2 3 5 7 104 ΔC = f (f) Capacitance Change vs. Frequency C 2 3 5 7 103 2 3 5 7 105 f (Hz) 0 - 60 Insulation resistance as a function of temperature Ris = f(TA), TLL ≤ TA ≤ TUL 105 - 40 - 20 0 20 40 60 80 100 120 Dissipation Factor (1 kHz) vs. Temperature tan δ = f (ϑ) 140 Tamb (°C) Dissipation factor as a function of frequency Δtan δ/tan δ = f(f), 100 Hz ≤ f ≤ 1 MHzL tan δ x 104 RC (s) 100 7 5 3 2 104 10 7 5 3 2 103 102 1 7 5 3 2 101 100 20 40 60 80 100 125 Tamb (°C) www.vishay.com 22 0.1 102 2 3 5 7 103 2 3 5 7 104 Dissipation Factor vs. Frequency tan δ = f (f) For technical questions, contact: [email protected] 2 3 5 7 105 f (Hz) Document Number: 26013 Revision: 08-Dec-08 MKT 1813 DC Film Capacitor MKT Axial Type Vishay Roederstein Maximum allowed component temperature rise (ΔT) as a function of the ambient temperature (Tamb) ΔT (°C) 16 12 8 4 0 - 60 - 20 20 60 T 100 amb (°C) HEAT CONDUCTIVITY (G) AS A FUNCTION OF (ORIGINAL) PITCH AND CAPACITOR BODY THICKNESS IN mW/°C HEAT CONDUCTIVITY (mW/°C) Dmax. (mm) L = 11 mm L = 14 mm L = 19 mm L = 26.5 mm L = 31.5 mm L = 41.5 mm 5.0 2 - - - - - 5.5 2 3 - - - - 6.0 - 3 4 - - - 6.5 - 3 5 - - - 7.0 - 4 5 - - - 7.5 - - 6 - - - 8.0 - 4 - 8 - - 8.5 - - 6 9 - - 9.0 - - 7 - - - 9.5 - - - 10 - - 10.0 - - - 11 - - 10.5 - - 8 - - - 11.0 - - - 12 14 - 11.5 - - - 13 15 - 12.0 - - 9 - 16 - 12.5 - - - - - - 13.0 - - - 14 17 - 13.5 - - - 15 18 - 14.0 - - - 16 19 - 14.5 - - - - 19 - 15.0 - - - - - - 15.5 - - - - 21 - 16.0 - - - - - 29 16.5 - - - - 22 30 17.0 - - - - - - 17.5 - - - - - 31 18.0 - - - - 24 - 18.5 - - - - - 34 19.0 - - - - - 20.0 - - - - - - 20.5 - - - - 28 - 21.0 - - - - - 38 Document Number: 26013 Revision: 08-Dec-08 For technical questions, contact: [email protected] www.vishay.com 23 MKT 1813 DC Film Capacitor MKT Axial Type Vishay Roederstein POWER DISSIPATION AND MAXIMUM COMPONENT TEMPERATURE RISE The power dissipation must be limited in order not to exceed the maximum allowed component temperature rise as a function of the free ambient temperature. The power dissipation can be calculated according type detail specification “HQN-384-01/101: Technical Information Film Capacitors”. The component temperature rise (ΔT) can be measured (see section “Measuring the component temperature” for more details) or calculated by ΔT = P/G: • ΔT = Component temperature rise (°C) • P = Power dissipation of the component (mW) • G = Heat conductivity of the component (mW/°C) MEASURING THE COMPONENT TEMPERATURE A thermocouple must be attached to the capacitor body as in: Thermocouple The temperature is measured in unloaded (Tamb) and maximum loaded condition (TC). The temperature rise is given by ΔT = TC - Tamb. To avoid radiation or convection, the capacitor should be tested in a wind-free box. APPLICATION NOTE AND LIMITING CONDITIONS These capacitors are not suitable for mains applications as across-the-line capacitors without additional protection, as described hereunder. These mains applications are strictly regulated in safety standards and therefore electromagnetic interference suppression capacitors conforming the standards must be used. To select the capacitor for a certain application, the following conditions must be checked: 1. The peak voltage (UP) shall not be greater than the rated DC voltage (URdc) 2. The peak-to-peak voltage (UP-P) shall not be greater than 2√2 x URac to avoid the ionisation inception level 3. The voltage peak slope (dU/dt) shall not exceed the rated voltage pulse slope in an RC-circuit at rated voltage and without ringing. If the pulse voltage is lower than the rated DC voltage, the rated voltage pulse slope may be multiplied by URdc and divided by the applied voltage. For all other pulses following equation must be fulfilled: T dU dU 2 2 × ∫ ⎛ --------⎞ × dt < U Rdc × ⎛ --------⎞ ⎝ dt ⎠ rated ⎝ dt ⎠ 0 T is the pulse duration The rated voltage pulse slope is valid for ambient temperatures up to 85 °C. For higher temperatures a derating factor of 3 % per K shall be applied. 4. The maximum component surface temperature rise must be lower than the limits (see figure max. allowed component temperature rise). www.vishay.com 24 For technical questions, contact: [email protected] Document Number: 26013 Revision: 08-Dec-08 MKT 1813 DC Film Capacitor MKT Axial Type Vishay Roederstein 5. Since in circuits used at voltages over 280 V peak-to-peak the risk for an intrinsically active flammability after a capacitor breakdown (short circuit) increases, it is recommended that the power to the component is limited to 100 times the values mentioned in the table: “Heat conductivity” 6. When using these capacitors as across-the-line capacitor in the input filter for mains applications or as series connected with an impedance to the mains the applicant must guarantee that the following conditions are fulfilled in any case (spikes and surge voltages from the mains included). Voltage Conditions for 6 Above Tamb ≤ 85 °C 85 °C < Tamb ≤ 100 °C URac 0.8 x URac Maximum temperature RMS-overvoltage (< 24 h) 1.25 x URac URac Maximum peak voltage (VO-P) (< 2 s) 1.6 x URdc 1.3 x URdc ALLOWED VOLTAGES Maximum continuous RMS voltage EXAMPLE C = 3300 nF - 100 V used for the voltage signal shown in next figure. UP-P = 80 V; UP = 70 V; T1 = 0.5 ms; T2 = 1 ms The ambient temperature is 35 °C Checking conditions: 1. The peak voltage UP = 70 V is lower than 100 Vdc 2. The peak-to-peak voltage 80 V is lower than 2√2 x 63 Vac = 178 UP-P 3. The voltage pulse slope (dU/dt) = 80 V/500 µs = 0.16 V/µs This is lower than 8 V/µs (see specific reference data for each version) 4. The dissipated power is 60 mW as calculated with fourier terms The temperature rise for Wmax. = 11.5 mm and pitch = 26.5 mm will be 60 mW/13 mW/°C = 4.6 °C This is lower than 15 °C temperature rise at 35 °C, according figure max. allowed component temperature rise 5. Not applicable 6. Not applicable Voltage Signal Voltage UP UP-P Time T1 T2 Document Number: 26013 Revision: 08-Dec-08 For technical questions, contact: [email protected] www.vishay.com 25 MKT 1813 Vishay Roederstein DC Film Capacitor MKT Axial Type INSPECTION REQUIREMENTS General Notes: Sub-clause numbers of tests and performance requirements refer to the “Sectional Specification, Publication IEC 60384-2 and Specific Reference Data”. Group C Inspection Requirements SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS SUB-GROUP C1A PART OF SAMPLE OF SUB-GROUP C1 4.1 Dimensions (detail) As specified in Chapters “General data” of this specification 4.3.1 Initial measurements Capacitance Tangent of loss angle: For C ≤ 470 nF at 100 kHz or for C > 470 nF at 10 kHz 4.3 Robustness of terminations Tensile: Load 10 N; 10 s Bending: Load 5 N; 4 x 90° 4.4 Resistance to soldering heat Method: 1A Solder bath: 280 °C ± 5 °C Duration: 10 s 4.14 Component solvent resistance Isopropylalcohol at room temperature Method: 2 Immersion time: 5 ± 0.5 min Recovery time: Min. 1 h, max. 2 h 4.4.2 Final measurements Visual examination No visible damage Legible marking Capacitance |ΔC/C| ≤ 2 % of the value measured initially Tangent of loss angle Increase of tan δ ≤ 0.005 for: C ≤ 100 nF or ≤ 0.010 for: 100 nF < C ≤ 220 nF or ≤ 0.015 for: 220 nF < C ≤ 470 nF and ≤ 0.003 for: C > 470 nF Compared to values measured in 4.3.1 No visible damage SUB-GROUP C1B PART OF SAMPLE OF SUB-GROUP C1 4.6.1 Initial measurements Capacitance Tangent of loss angle: For C ≤ 470 nF at 100 kHz or for C > 470 nF at 10 kHz 4.6 Rapid change of temperature θA = - 55 °C θB = + 100 °C 5 cycles Duration t = 30 min Visual examination 4.7 Vibration Mounting: See section “Mounting” of this specification Procedure B4 Frequency range: 10 Hz to 55 Hz Amplitude: 0.75 mm or Acceleration 98 m/s² (whichever is less severe) Total duration 6 h 4.7.2 Final inspection Visual examination www.vishay.com 26 For technical questions, contact: [email protected] No visible damage No visible damage Document Number: 26013 Revision: 08-Dec-08 MKT 1813 DC Film Capacitor MKT Axial Type Vishay Roederstein SUB-CLAUSE NUMBER AND TEST CONDITIONS 4.9 Shock Mounting: See section “Mounting” of this specification Pulse shape: Half sine Acceleration: 490 m/s² Duration of pulse: 11 ms PERFORMANCE REQUIREMENTS 4.9.3 Final measurements Visual examination No visible damage Capacitance |ΔC/C| ≤ 3 % of the value measured in 4.6.1 Tangent of loss angle Increase of tan δ ≤ 0.005 for: C ≤ 100 nF or ≤ 0.010 for: 100 nF < C ≤ 220 nF or ≤ 0.015 for: 220 nF < C ≤ 470 nF and ≤ 0.003 for: C > 470 nF Compared to values measured in 4.6.1 Insulation resistance As specified in section “Insulation Resistance” of this specification SUB-GROUP C1 COMBINED SAMPLE OF SPECIMENS OF SUB-GROUPS C1A AND C1B 4.10 Climatic sequence 4.10.2 Dry heat 4.10.3 Damp heat cyclic Test Db, first cycle 4.10.4 Cold 4.10.6 Damp heat cyclic Test Db, remaining cycles 4.10.6.2 Final measurements Temperature: + 100 °C Duration: 16 h Temperature: - 55 °C Duration: 2 h Voltage proof = URdc for 1 min within 15 min after removal from testchamber No breakdown of flash-over Visual examination No visible damage Legible marking Capacitance |ΔC/C| ≤ 5 % of the value measured in 4.4.2 or 4.9.3 Tangent of loss angle Increase of tan δ ≤ 0.007 for: C ≤ 100 nF or ≤ 0.010 for: 100 nF < C ≤ 220 nF or ≤ 0.015 for: 220 nF < C ≤ 470 nF and ≤ 0.005 for: C > 470 nF Compared to values measured in 4.3.1 or 4.6.1 Insulation resistance ≥ 50 % of values specified in section “Insulation resistance” of this specification SUB-GROUP C2 4.11 Damp heat steady state 56 days, 40 °C, 90 % to 95 % RH 4.11.1 Initial measurements Capacitance Tangent of loss angle at 1 kHz Document Number: 26013 Revision: 08-Dec-08 For technical questions, contact: [email protected] www.vishay.com 27 MKT 1813 Vishay Roederstein DC Film Capacitor MKT Axial Type SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS 4.11.3 Voltage proof = URdc for 1 min within 15 min after removal from testchamber No breakdown of flash-over Visual examination No visible damage Legible marking Capacitance |ΔC/C| ≤ 5 % of the value measured in 4.11.1. Tangent of loss angle Increase of tan δ ≤ 0.005 Compared to values measured in 4.11.1 Insulation resistance ≥ 50 % of values specified in section “Insulation resistance” of this specification Final measurements SUB-GROUP C3 4.12 Endurance Duration: 2000 h 1.25 x URdc at 85 °C 1.0 x URdc at 100 °C 4.12.1 Initial measurements Capacitance Tangent of loss angle: For C ≤ 470 nF at 100 kHz or for C > 470 nF at 10 kHz 4.12.5 Final measurements Visual examination No visible damage Legible marking Capacitance |ΔC/C| ≤ 5 % compared to values measured in 4.12.1 Tangent of loss angle Increase of tan δ ≤ 0.005 for: C ≤ 100 nF or ≤ 0.010 for: 100 nF < C ≤ 220 nF or ≤ 0.015 for: 220 nF < C ≤ 470 nF and ≤ 0.003 for: C > 470 nF Compared to values measured in 4.12.1 Insulation resistance ≥ 50 % of values specified in section “Insulation resistance” of this specification SUB-GROUP C4 4.13 Charge and discharge 10 000 cycles Charged to URdc Discharge resistance: UR R = ------------------------------------------------C × 2.5 × ( dU ⁄ dt ) R 4.13.1 Initial measurements Capacitance Tangent of loss angle: For C ≤ 470 nF at 100 kHz or for C > 470 nF at 10 kHz 4.13.3 Final measurements Capacitance |ΔC/C| ≤ 3 % compared to values measured in 4.13.1 Tangent of loss angle Increase of tan δ ≤ 0.005 for: C ≤ 100 nF or ≤ 0.010 for: 100 nF < C ≤ 220 nF or ≤ 0.015 for: 220 nF < C ≤ 470 nF and ≤ 0.003 for: C > 470 nF Compared to values measured in 4.13.1 Insulation resistance ≥ 50 % of values specified in section “Insulation resistance” of this specification www.vishay.com 28 For technical questions, contact: [email protected] Document Number: 26013 Revision: 08-Dec-08 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1