FREESCALE MPC8313ECVRAFF

Freescale Semiconductor
Technical Data
Document Number: MPC8313EEC
Rev. 0, 06/2007
MPC8313E
PowerQUICC™ II Pro Processor
Hardware Specifications
This document provides an overview of the MPC8313E
PowerQUICC™ II Pro processor features, including a block
diagram showing the major functional components. The
MPC8313E is a cost-effective, low-power, highly integrated
host processor that addresses the requirements of several
printing and imaging, consumer, and industrial applications,
including main CPUs and I/O processors in printing systems,
networking switches and line cards, wireless LANs
(WLANs), network access servers (NAS), VPN routers,
intelligent NIC, and industrial controllers. The MPC8313E
extends the PowerQUICC™ family, adding higher CPU
performance, additional functionality, and faster interfaces
while addressing the requirements related to time-to-market,
price, power consumption, and package size.
1
Overview
The MPC8313E incorporates the e300c3 core, which
includes 16 Kbytes of L1 instruction and data caches and
on-chip memory management units (MMUs). The
MPC8313E has interfaces to dual enhanced three-speed 10,
100, 1000 Mbps Ethernet controllers, a DDR1/DDR2
SDRAM memory controller, an enhanced local bus
controller, a 32-bit PCI controller, a dedicated security
This document contains information on a new product. Specifications and information herein
are subject to change without notice.
© Freescale Semiconductor, Inc., 2007. All rights reserved.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
Contents
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . 7
Power Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 11
Clock Input Timing . . . . . . . . . . . . . . . . . . . . . . . . . . 13
RESET Initialization . . . . . . . . . . . . . . . . . . . . . . . . . 14
DDR and DDR2 SDRAM . . . . . . . . . . . . . . . . . . . . . 16
DUART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Ethernet: Three-Speed Ethernet, MII Management . 23
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Local Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
JTAG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
I2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
PCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
GPIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
IPIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Package and Pin Listings . . . . . . . . . . . . . . . . . . . . . 56
Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Thermal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
System Design Information . . . . . . . . . . . . . . . . . . . 81
Document Revision History . . . . . . . . . . . . . . . . . . . 87
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . 87
Overview
engine, a USB 2.0 dual-role controller and an on-chip full-speed PHY, a programmable interrupt
controller, dual I2C controllers, a 4-channel DMA controller, and a general-purpose I/O port. A block
diagram of the MPC8313E is shown in Figure 1.
DUART
Dual I 2C
Timers
GPIO
e300c3 Core w/FPU and
Power Management
Interrupt
Controller
I/O Sequencer
(IOS)
PCI
16-KB
I-Cache
Security Engine 2.2
16-KB
D-Cache
USB 2.0
Host/Device/OTG
ULPI On-Chip
FS PHY
Local Bus,
SPI
DDR1/DDR2
Controller
Gb Ethernet
MAC
Gb Ethernet
MAC
DMA
Note: The MPC8313 does not include
a security engine.
Figure 1. MPC8313E Block Diagram
The MPC8313E’s security engine (SEC 2.2) allows CPU-intensive cryptographic operations to be
offloaded from the main CPU core. The security-processing accelerator provides hardware acceleration
for the DES, 3DES, AES, SHA-1, and MD-5 algorithms.
1.1
MPC8313E Features
The following features are supported in the MPC8313E.
• Embedded PowerPCTM e300 processor core; operates at up to 333 MHz.
• High-performance, low-power, and cost-effective host processor
• DDR1/DDR2 memory controller—one 16-/32-bit interface at up to 333 MHz supporting both
DDR1 and DDR2
• e300c3 core, built on Power Architecture™ technology, with 16-Kbyte instruction cache and
16-Kbyte data cache, a floating point unit, and two integer units
• Peripheral interfaces such as 32-bit PCI interface with up to 66-MHz operation, 16-bit enhanced
local bus interface with up to 66-MHz operation, and USB 2.0 (full speed) with an on-chip PHY.
• Security engine provides acceleration for control and data plane security protocols
• Power management controller for low-power consumption
• High degree of software compatibility with previous-generation PowerQUICC processor-based
designs for backward compatibility and easier software migration
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
2
Freescale Semiconductor
Overview
1.2
Serial Interfaces
The following interfaces are supported in the MPC8313E.
• Dual UART, dual I2C, and an SPI interface
1.3
Security Engine
The security engine is optimized to handle all the algorithms associated with IPSec, IEEE Std. 802.11i™,
and iSCSI. The security engine contains one crypto-channel, a controller, and a set of crypto execution
units (EUs). The execution units are:
• Data encryption standard execution unit (DEU), supporting DES and 3DES
• Advanced encryption standard unit (AESU), supporting AES
• Message digest execution unit (MDEU), supporting MD5, SHA1, SHA-224, SHA-256, and
HMAC with any algorithm
• One crypto-channel supporting multi-command descriptor chains
1.4
DDR Memory Controller
The MPC8313E DDR1/DDR2 memory controller includes the following features:
• Single 16- or 32-bit interface supporting both DDR1 and DDR2 SDRAM
• Support for up to 333-MHz
• Support for two physical banks (chip selects), each bank independently addressable
• 64-Mbit to 1-Gbit devices with x8/x16/x32 data ports (no direct x4 support)
• Support for one 16-bit device or two 8-bit devices on a 16-bit bus OR one 32-bit device or two
16-bit devices on a 32-bit bus
• Support for up to 16 simultaneous open pages
• Supports auto refresh
• On-the-fly power management using CKE
• 1.8-/2.5-V SSTL2 compatible I/O
1.5
PCI Controller
The MPC8313E PCI controller includes the following features:
• PCI specification revision 2.3 compatible
• Single 32-bit data PCI interface operates at up to 66 MHz
• PCI 3.3-V compatible (not 5-V compatible)
• Support for host and agent modes
• On-chip arbitration, supporting three external masters on PCI
• Selectable hardware-enforced coherency
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
3
Overview
1.6
USB Dual-Role Controller
The MPC8313E USB controller includes the following features:
• Supports USB on-the-go mode, which includes both device and host functionality, when using an
external ULPI (UTMI + low-pin interface) PHY
• Complies with USB Specification, Rev. 2.0
• Supports operation as a stand-alone USB device
— Supports one upstream facing port
— Supports three programmable USB endpoints
• Supports operation as a stand-alone USB host controller
— Supports USB root hub with one downstream-facing port
— Enhanced host controller interface (EHCI) compatible
• Supports full-speed (12 Mbps), and low-speed (1.5 Mbps) operation. Low-speed operation is
supported only in host mode.
• Supports UTMI + low pin interface (ULPI) or on-chip USB-2.0 full-speed PHY
1.7
Dual Enhanced Three-Speed Ethernet Controllers (eTSECs)
The MPC8313E eTSECs include the following features:
• Two RGMII/SGMII/MII/RMII/RTBI interfaces
• Two controllers designed to comply with IEEE Stds. 802.3™, 802.3u™, 802.3x™, 802.3z™,
802.3au™, and 802.3ab™
• Support for Wake-on-Magic Packet™, a method to bring the device from standby to full operating
mode
• MII management interface for external PHY control and status
• Three-speed support (10/100/1000 Mbps)
• On-chip high-speed serial interface to external SGMII PHY interface
• Support for IEEE Std. 1588™
• Support for two full-duplex FIFO interface modes
• Multiple PHY interface configuration
• TCP/IP acceleration and QoS features available
• IP v4 and IP v6 header recognition on receive
• IP v4 header checksum verification and generation
• TCP and UDP checksum verification and generation
• Per-packet configurable acceleration
• Recognition of VLAN, stacked (queue in queue) VLAN, IEEE Std. 802.2™, PPPoE session,
MPLS stacks, and ESP/AH IP-security headers
• Transmission from up to eight physical queues.
• Reception to up to eight physical queues
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
4
Freescale Semiconductor
Overview
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1.8
Full- and half-duplex Ethernet support (1000 Mbps supports only full-duplex):
IEEE Std. 802.3 full-duplex flow control (automatic PAUSE frame generation or
software-programmed PAUSE frame generation and recognition)
Programmable maximum frame length supports jumbo frames (up to 9.6 Kbytes) and
IEEE Std. 802.1™ virtual local area network (VLAN) tags and priority
VLAN insertion and deletion
Per-frame VLAN control word or default VLAN for each eTSEC
Extracted VLAN control word passed to software separately
Retransmission following a collision
CRC generation and verification of inbound/outbound packets
Programmable Ethernet preamble insertion and extraction of up to 7 bytes
MAC address recognition:
Exact match on primary and virtual 48-bit unicast addresses
VRRP and HSRP support for seamless router fail-over
Up to 16 exact-match MAC addresses supported
Broadcast address (accept/reject)
Hash table match on up to 512 multicast addresses
Promiscuous mode
Buffer descriptors backward compatible with MPC8260 and MPC860T 10/100 Ethernet
programming models
RMON statistics support
10-Kbyte internal transmit and 2-Kbyte receive FIFOs
MII management interface for control and status
Programmable Interrupt Controller (PIC)
The programmable interrupt controller (PIC) implements the necessary functions to provide a flexible
solution for general-purpose interrupt control. The PIC programming model supports 5 external and 34
internal discrete interrupt sources. Interrupts can also be redirected to an external interrupt controller.
1.9
Power Management Controller (PMC)
The MPC8313E power management controller includes the following features:
• Provides power management when the device is used in both host and agent modes
• Supports PCI Power Management 1.2 D0, D1, D2, D3hot, and D3cold states
• On-chip split power supply controlled through external power switch for minimum standby power
• Support for PME generation in PCI agent mode, PME detection in PCI host mode
• Supports wake-up from Ethernet (magic packet), USB, GPIO, and PCI (PME input as host)
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
5
Overview
1.10
Serial Peripheral Interface (SPI)
The serial peripheral interface (SPI) allows the MPC8313E to exchange data between other PowerQUICC
family chips, Ethernet PHYs for configuration, and peripheral devices such as EEPROMs, real-time
clocks, A/D converters, and ISDN devices.
The SPI is a full-duplex, synchronous, character-oriented channel that supports a four-wire interface
(receive, transmit, clock, and slave select). The SPI block consists of transmitter and receiver sections, an
independent baud-rate generator, and a control unit.
1.11
DMA Controller, Dual I2C, DUART, Local Bus Controller, and
Timers
The MPC8313E provides an integrated four-channel DMA controller with the following features:
• Allows chaining (both extended and direct) through local memory-mapped chain descriptors
(accessible by local masters).
• Supports misaligned transfers
There are two I2C controllers. These synchronous, multi-master buses can be connected to additional
devices for expansion and system development.
The DUART supports full-duplex operation and is compatible with the PC16450 and PC16550
programming models. 16-byte FIFOs are supported for both the transmitter and the receiver.
The MPC8313E local bus controller (LBC) port allows connections with a wide variety of external DSPs
and ASICs. Three separate state machines share the same external pins and can be programmed separately
to access different types of devices. The general-purpose chip select machine (GPCM) controls accesses
to asynchronous devices using a simple handshake protocol. The three user programmable machines
(UPMs) can be programmed to interface to synchronous devices or custom ASIC interfaces. Each chip
select can be configured so that the associated chip interface can be controlled by the GPCM or UPM
controller. The FCM provides a glueless interface to parallel-bus NAND Flash E2PROM devices. The
FCM contains three basic configuration register groups–BRn, ORn, and FMR. Both may exist in the same
system. The local bus can operate at up to 66 MHz.
The MPC8313E system timers include the following features: periodic interrupt timer, real time clock,
software watchdog timer, and two general-purpose timer blocks.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
6
Freescale Semiconductor
Electrical Characteristics
2
Electrical Characteristics
This section provides the AC and DC electrical specifications and thermal characteristics for the
MPC8313E. The MPC8313E is currently targeted to these specifications. Some of these specifications are
independent of the I/O cell, but are included for a more complete reference. These are not purely I/O buffer
design specifications.
2.1
Overall DC Electrical Characteristics
This section covers the ratings, conditions, and other characteristics.
2.1.1
Absolute Maximum Ratings
Table 1 provides the absolute maximum ratings.
Table 1. Absolute Maximum Ratings 1
Characteristic
Symbol
Max Value
Unit
Core supply voltage
VDD
–0.3 to 1.26
V
PLL supply voltage
AV DD
–0.3 to 1.26
V
DDR and DDR2 DRAM I/O voltage
GVDD
–0.3 to 2.75
–0.3 to 1.98
V
NVDD/LVDD
–0.3 to 3.6
V
LVDDA/LVDDB
–0.3 to 3.6
V
MVIN
–0.3 to (GVDD + 0.3)
V
2, 5
MVREF
–0.3 to (GVDD + 0.3)
V
2, 5
Enhanced Three-speed Ethernet signals
LVIN
–0.3 to (LVDDA + 0.3)
or
–0.3 to (LVDDB + 0.3)
V
4, 5
Local bus, DUART, SYS_CLK_IN, system
control, and power management, I2C, and
JTAG signals
OVIN
–0.3 to (NVDD + 0.3)
V
3, 5
PCI
OVIN
–0.3 to (NVDD + 0.3)
V
6
PCI, local bus, DUART, system control and power
management, I2C, and JTAG I/O voltage
eTSEC, USB
Input voltage
DDR DRAM signals
DDR DRAM reference
Notes
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
7
Electrical Characteristics
Table 1. Absolute Maximum Ratings 1 (continued)
Characteristic
Storage temperature range
Symbol
Max Value
Unit
TSTG
–55 to 150
°C
Notes
Notes:
1. Functional and tested operating conditions are given in Table 2. Absolute maximum ratings are stress ratings only, and
functional operation at the maximums is not guaranteed. Stresses beyond those listed may affect device reliability or cause
permanent damage to the device.
2. Caution: MVIN must not exceed GVDD by more than 0.3 V. This limit may be exceeded for a maximum of 20 ms during
power-on reset and power-down sequences.
3. Caution: OVIN must not exceed NVDD by more than 0.3 V. This limit may be exceeded for a maximum of 20 ms during
power-on reset and power-down sequences.
4. Caution: LVIN must not exceed LVDDA/LVDDB by more than 0.3 V. This limit may be exceeded for a maximum of 20 ms
during power-on reset and power-down sequences.
5. (L,M,O)VIN and MV REF may overshoot/undershoot to a voltage and for a maximum duration as shown in Figure 2.
6. OVIN on the PCI interface may overshoot/undershoot according to the PCI Electrical Specification for 3.3-V operation, as
shown in Figure 3.
2.1.2
Power Supply Voltage Specification
Table 2 provides the recommended operating conditions for the MPC8313E. Note that the values in
Table 2 are the recommended and tested operating conditions. Proper device operation outside of these
conditions is not guaranteed.
Table 2. Recommended Operating Conditions
Symbol
Recommended
Value1
Unit
Current
requirement
SerDes (Lynx) internal digital power
XCOREVDD
1.0
V
100 mA
SerDes (Lynx) internal digital power
XCOREVSS
0.0
V
SerDes (Lynx) I/O digital power
XPADVDD
1.0
V
SerDes (Lynx) I/O digital power
XPADVSS
0.0
V
SerDes (Lynx) analog power for PLL
SDAVDD
1.0
V
SerDes (Lynx) analog power for PLL
SDAVSS
0.0
V
Dedicated 3.3 V analog power for USB PLL
USB_PLL_PWR3
3.3
V
2–3 mA
Dedicated 1.0 V analog power for USB PLL
USB_PLL_PWR1
1.0
V
2–3 mA
USB_PLL_GND
0.0
V
Dedicated USB power for USB Bias circuit
USB_VDDA_BIAS
3.3
V
Dedicated USB ground for USB Bias circuit
USB_VSSA_BIAS
0.0
V
Dedicated power for USB Transceiver
USB_VDDA
3.3
V
Dedicated ground for USB transceiver
USB_VSSA
0.0
V
Core supply voltage
VDD
1.0
V
560 mA
Internal core logic constant power
VDDC
1.0
V
454 mA
Characteristic
Dedicated analog ground for USB PLL
10mA
10 mA
4–5 mA
75 mA
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
8
Freescale Semiconductor
Electrical Characteristics
Table 2. Recommended Operating Conditions (continued)
Symbol
Recommended
Value1
Unit
Current
requirement
Analog power for e300 core APLL
AVDD1
1.0
V
10 mA
Analog power for system APLL
AVDD2
1.0
V
10 mA
DDR and DDR2 DRAM I/O voltage
GVDD
2.5/1.8
V
425 mA
Differential reference voltage for DDR controller
MVREF
1/2 DDR Supply
V
Standard I/O Voltage
NVDD
3.3
V
27 mA
eTSEC2 IO Supply
LVDDA
2.5/3.3
V
85 mA
eTSEC1/USB DR IO Supply
LVDDB
2.5/3.3
V
85 mA
Supply for eLBCIOs
LVDD
3.3
V
60 mA
Analog and Digital Ground
VSS
0.0
V
Characteristic
Notes:
1. GVDD, OVDD, AVDD, and VDD must track each other and must vary in the same direction–either in the positive or negative
direction.
Figure 2 shows the undershoot and overshoot voltages at the interfaces of the MPC8313E.
G/L/NVDD + 20%
G/L/NVDD + 5%
G/L/NVDD
VIH
VSS
VSS – 0.3 V
VIL
VSS – 0.7 V
Not to Exceed 10%
of tinterface1
Note:
1. Note that tinterface refers to the clock period associated with the bus clock interface.
Figure 2. Overshoot/Undershoot Voltage for GVDD/NVDD/LVDD
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
9
Electrical Characteristics
Figure 3 shows the undershoot and overshoot voltage of the PCI interface of the MPC8313E for the 3.3-V
signals, respectively.
11 ns
(Min)
+7.1 V
7.1 V p-to-p
(Min)
Overvoltage
Waveform
4 ns
(Max)
0V
4 ns
(Max)
62.5 ns
+3.6 V
7.1 V p-to-p
(Min)
Undervoltage
Waveform
–3.5 V
Figure 3. Maximum AC Waveforms on PCI Interface for 3.3-V Signaling
2.1.3
Output Driver Characteristics
Table 3 provides information on the characteristics of the output driver strengths. The values are
preliminary estimates.
Table 3. Output Drive Capability
Output Impedance
(Ω)
Supply
Voltage
Local bus interface utilities signals
42
NVDD = 3.3 V
PCI signals
25
DDR signal
18
GVDD = 2.5 V
DDR2 signal
18
GVDD = 1.8 V
DUART, system control, I2C, JTAG,SPI
42
NVDD = 3.3 V
GPIO signals
42
NVDD = 3.3 V
eTSEC signals
42
LVDDA, LV DDB = 2.5/3.3 V
USB Signals
42
LVDDB = 2.5/3.3 V
Driver Type
2.2
Power Sequencing
The MPC8313E does not require the core supply voltage and IO supply voltages to be applied in any
particular order. Note that during the power ramp-up, before the power supplies are stable, there might be
a period when IO pins are actively driven. After the power is stable, as long as PORESET is asserted, most
IO pins are tri-stated. In order to minimize the time that IO pins are being actively driven, it is
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
10
Freescale Semiconductor
Power Characteristics
recommended to apply core voltage before IO voltage and assert PORESET before the power supplies
fully ramp up.
3
Power Characteristics
The estimated typical power dissipation for this family of MPC8313E devices is shown in Table 4, and
Table 5 shows the estimated typical I/O power dissipation.
Table 4. MPC8313E Power Dissipation 1
.
Core Frequency (MHz)
CSB Frequency (MHz)
Typical 2, 3
Maximum 2,3
Unit
267
133
680
880
mW
333
167
820
1020
mW
Note:
1. The values do not include I/O supply power or AVdd.
2. Typical power is based on a voltage of Vdd = 1.05V, a junction temperature of Tj = 105°C, and an artificial
smoker test.
3. These are preliminary estimates
1
Table 5. MPC8313E Typical I/O Power Dissipation
Interface
Parameter
DDR 1, 60% utilzation, 333MHz, 32 bits
50% read/write
266MHz, 32 bits
Rs = 22Ω
Rt = 50Ω
200MHz, 32 bits
single pair of clock
Capacitive Load:
Data = 8pF, Control
Address = 8pF,
Clock = 8pF
GVDD GVDD NVDD LVDDA/LV DDB LVDDA/LVDDB LVDDB
Unit Comments
(1.8 V) (2.5 V) (3.3 V)
(3.3V)
(2.5V)
(3.3V)
—
0.355
W
—
0.323
W
—
0.291
W
—
W
—
W
—
W
DDR 2, 60% utilization, 333MHz, 32 bits 0.266
50% read/write
266MHz, 32 bits 0.246
Rs = 22Ω
Rt = 75Ω
200MHz, 32bits 0.225
single pair of clock
Capacitive Load:
Data = 8pF, Control
Address = 8pF,
Clock = 8pF
PCI I/O load = 50pF
Local bus I/O
load = 20pF
33 MHz
0.120
W
66 MHz
0.249
W
66 MHz
0.056
W
50 MHz
0.040
W
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
11
Power Characteristics
Table 5. MPC8313E Typical I/O Power Dissipation (continued)
TSEC I/O load = 20pF
MII, 25MHz
0.008
RGMII, 125MHz
USBDR controller
load = 20pF
Other I/O
W
0.044
60 MHz
W
0.078
0.015
Multiple by
number of
interface
used
W
W
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
12
Freescale Semiconductor
Clock Input Timing
4
Clock Input Timing
This section provides the clock input DC and AC electrical characteristics for the MPC8313E.
4.1
DC Electrical Characteristics
Table 6 provides the clock input (SYS_CLK_IN/PCI_SYNC_IN) DC timing specifications for the
MPC8313E.
Table 6. SYS_CLK_IN DC Electrical Characteristics
Parameter
Condition
Symbol
Min
Max
Unit
Input high voltage
—
VIH
2.7
NVDD + 0.3
V
Input low voltage
—
VIL
–0.3
0.4
V
SYS_CLK_IN Input current
0 V ≤ VIN ≤ NVDD
IIN
—
±10
μA
PCI_SYNC_IN Input current
0 V ≤ VIN ≤ 0.5 V or
NVDD – 0.5 V ≤ VIN ≤ NV DD
IIN
—
±10
μA
PCI_SYNC_IN Input current
0.5 V ≤ VIN ≤ NVDD – 0.5 V
IIN
—
±50
μA
4.2
AC Electrical Characteristics
The primary clock source for the MPC8313E can be one of two inputs, SYS_CLK_IN or PCI_CLK,
depending on whether the device is configured in PCI host or PCI agent mode. Table 7 provides the clock
input (SYS_CLK_IN/PCI_CLK) AC timing specifications for the MPC8313E.
Table 7. SYS_CLK_IN AC Timing Specifications
Parameter/Condition
Symbol
Min
Typical
Max
Unit
Notes
SYS_CLK_IN/PCI_CLK frequency
fSYS_CLK_IN
25
—
66
MHz
1
SYS_CLK_IN/PCI_CLK cycle time
tSYS_CLK_IN
15
—
—
ns
—
tKH, tKL
0.6
0.8
1.2
ns
2
tKHK/tSYS_CLK_IN
40
—
60
%
3
—
—
—
±150
ps
4, 5
SYS_CLK_IN/PCI_CLK rise and fall time
SYS_CLK_IN/PCI_CLK duty cycle
SYS_CLK_IN/PCI_CLK jitter
Notes:
1. Caution: The system, core, security block must not exceed their respective maximum or minimum operating frequencies.
2. Rise and fall times for SYS_CLK_IN/PCI_CLK are measured at 0.4 V and 2.7 V.
3. Timing is guaranteed by design and characterization.
4. This represents the total input jitter—short term and long term—and is guaranteed by design.
5. The SYS_CLK_IN/PCI_CLK driver’s closed loop jitter bandwidth should be < 500 kHz at –20 dB. The bandwidth must be set
low to allow cascade-connected PLL-based devices to track SYS_CLK_IN drivers with the specified jitter.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
13
RESET Initialization
5
RESET Initialization
This section describes the DC and AC electrical specifications for the reset initialization timing and
electrical requirements of the MPC8313E.
5.1
RESET DC Electrical Characteristics
Table 8 provides the DC electrical characteristics for the RESET pins.
Table 8. RESET Pins DC Electrical Characteristics
Characteristic
5.2
Symbol
Condition
Min
Max
Unit
Input high voltage
VIH
2.0
NVDD + 0.3
V
Input low voltage
VIL
–0.3
0.8
V
Input current
IIN
0 V ≤ VIN ≤ NVDD
±5
μA
Output high voltage
VOH
IOH = –8.0 mA
2.4
—
V
Output low voltage
VOL
IOL = 8.0 mA
—
0.5
V
Output low voltage
VOL
IOL = 3.2 mA
—
0.4
V
RESET AC Electrical Characteristics
Table 9 provides the reset initialization AC timing specifications.
Table 9. RESET Initialization Timing Specifications
Parameter/Condition
Min
Max
Unit
Notes
Required assertion time of HRESET or SRESET (input) to
activate reset flow
32
—
tPCI_SYNC_IN
1
Required assertion time of PORESET with stable clock applied
to SYS_CLK_IN when the device is in PCI host mode
32
—
tSYS_CLK_IN
2
Required assertion time of PORESET with stable clock applied
to PCI_SYNC_IN when the device is in PCI agent mode
32
—
tPCI_SYNC_IN
1
HRESET/ SRESET assertion (output)
512
—
tPCI_SYNC_IN
1
HRESET negation to SRESET negation (output)
16
—
tPCI_SYNC_IN
1
Input setup time for POR configuration signals
(CFG_RESET_SOURCE[0:3] and CFG_SYS_CLK_IN_DIV )
with respect to negation of PORESET when the device is in PCI
host mode
4
—
tSYS_CLK_IN
2
Input setup time for POR configuration signals
(CFG_RESET_SOURCE[0:2] and CFG_CLKIN_DIV) with
respect to negation of PORESET when the device is in PCI
agent mode
4
—
tPCI_SYNC_IN
1
Input hold time for POR configuration signals with respect to
negation of HRESET
0
—
ns
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
14
Freescale Semiconductor
RESET Initialization
Table 9. RESET Initialization Timing Specifications (continued)
Time for the device to turn off POR configuration signals with
respect to the assertion of HRESET
—
4
ns
3
Time for the device to turn on POR configuration signals with
respect to the negation of HRESET
1
—
tPCI_SYNC_IN
1, 3
Notes:
1. tPCI_SYNC_IN is the clock period of the input clock applied to PCI_SYNC_IN. When the device is In PCI host mode the primary
clock is applied to the SYS_CLK_IN input, and PCI_SYNC_IN period depends on the value of CFG_CLKIN_DIV.
2. tSYS_CLK_IN is the clock period of the input clock applied to SYS_CLK_IN. It is only valid when the device is in PCI host mode.
3. POR configuration signals consists of CFG_RESET_SOURCE[0:2] and CFG_CLKIN_DIV.
Table 10 provides the PLL lock times.
Table 10. PLL Lock Times
Parameter/Condition
PLL lock times
Min
Max
Unit
—
100
μs
Notes
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
15
DDR and DDR2 SDRAM
6
DDR and DDR2 SDRAM
This section describes the DC and AC electrical specifications for the DDR SDRAM interface. Note that
DDR SDRAM is GVDD(typ) = 2.5 V and DDR2 SDRAM is GVDD(typ) = 1.8 V.
6.1
DDR and DDR2 SDRAM DC Electrical Characteristics
Table 11 provides the recommended operating conditions for the DDR2 SDRAM component(s) when
GVDD(typ) = 1.8 V.
Table 11. DDR2 SDRAM DC Electrical Characteristics for GVDD(typ) = 1.8 V
Parameter/Condition
Symbol
Min
Max
Unit
Notes
I/O supply voltage
GVDD
1.7
1.9
V
1
I/O reference voltage
MV REF
0.49 × GVDD
0.51 × GVDD
V
2
I/O termination voltage
VTT
MVREF – 0.04
MVREF + 0.04
V
3
Input high voltage
VIH
MVREF + 0.125
GVDD + 0.3
V
Input low voltage
VIL
–0.3
MV REF – 0.125
V
Output leakage current
IOZ
–9.9
9.9
μA
Output high current (VOUT = 1.420 V)
IOH
–13.4
—
mA
Output low current (VOUT = 0.280 V)
IOL
13.4
—
mA
4
Notes:
1. GVDD is expected to be within 50 mV of the DRAM GVDD at all times.
2. MVREF is expected to be equal to 0.5 × GVDD, and to track GVDD DC variations as measured at the receiver. Peak-to-peak
noise on MVREF may not exceed ±2% of the DC value.
3. VTT is not applied directly to the device. It is the supply to which far end signal termination is made and is expected to be
equal to MV REF. This rail should track variations in the DC level of MVREF.
4. Output leakage is measured with all outputs disabled, 0 V ≤ VOUT ≤ GVDD.
Table 12 provides the DDR2 capacitance when GVDD(typ) = 1.8 V.
Table 12. DDR2 SDRAM Capacitance for GVDD(typ)=1.8 V
Parameter/Condition
Symbol
Min
Max
Unit
Notes
Input/output capacitance: DQ, DQS, DQS
CIO
6
8
pF
1
Delta input/output capacitance: DQ, DQS, DQS
CDIO
—
0.5
pF
1
Note:
1. This parameter is sampled. GV DD = 1.8 V ± 0.090 V, f = 1 MHz, TA = 25°C, VOUT = GVDD/2, VOUT (peak-to-peak) = 0.2 V.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
16
Freescale Semiconductor
DDR and DDR2 SDRAM
Table 13 provides the recommended operating conditions for the DDR SDRAM component(s) when
GVDD(typ) = 2.5 V.
Table 13. DDR SDRAM DC Electrical Characteristics for GVDD (typ) = 2.5 V
Parameter/Condition
Symbol
Min
Max
Unit
Notes
I/O supply voltage
GVDD
2.3
2.7
V
1
I/O reference voltage
MVREF
0.49 × GVDD
0.51 × GVDD
V
2
I/O termination voltage
VTT
MVREF – 0.04
MVREF + 0.04
V
3
Input high voltage
VIH
MVREF + 0.15
GVDD + 0.3
V
Input low voltage
VIL
–0.3
MVREF – 0.15
V
Output leakage current
IOZ
–9.9
–9.9
μA
Output high current (VOUT = 1.95 V)
IOH
–16.2
—
mA
Output low current (VOUT = 0.35 V)
IOL
16.2
—
mA
4
Notes:
1. GVDD is expected to be within 50 mV of the DRAM GVDD at all times.
2. MVREF is expected to be equal to 0.5 × GVDD, and to track GV DD DC variations as measured at the receiver. Peak-to-peak
noise on MVREF may not exceed ±2% of the DC value.
3. VTT is not applied directly to the device. It is the supply to which far end signal termination is made and is expected to be
equal to MVREF. This rail should track variations in the DC level of MVREF.
4. Output leakage is measured with all outputs disabled, 0 V ≤ VOUT ≤ GVDD.
Table 14 provides the DDR capacitance when GVDD (typ)=2.5 V.
Table 14. DDR SDRAM Capacitance for GVDD (typ) = 2.5 V
Parameter/Condition
Symbol
Min
Max
Unit
Notes
Input/output capacitance: DQ, DQS
CIO
6
8
pF
1
Delta input/output capacitance: DQ, DQS
CDIO
—
0.5
pF
1
Note:
1. This parameter is sampled. GVDD = 2.5 V ± 0.125 V, f = 1 MHz, TA = 25°C, VOUT = GVDD /2,
VOUT (peak-to-peak) = 0.2 V.
Table 15 provides the current draw characteristics for MVREF.
Table 15. Current Draw Characteristics for MVREF
Parameter / Condition
Current draw for MVREF
Symbol
Min
Max
Unit
Note
IMVREF
—
500
μA
1
1. The voltage regulator for MVREF must be able to supply up to 500 μA current.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
17
DDR and DDR2 SDRAM
6.2
DDR and DDR2 SDRAM AC Electrical Characteristics
This section provides the AC electrical characteristics for the DDR SDRAM interface.
6.2.1
DDR and DDR2 SDRAM Input AC Timing Specifications
Table 16 provides the input AC timing specifications for the DDR2 SDRAM when GVDD(typ)=1.8 V.
Table 16. DDR2 SDRAM Input AC Timing Specifications for 1.8-V Interface
At recommended operating conditions with GVDD of 1.8 ±5%
Parameter
Symbol
Min
Max
Unit
AC input low voltage
VIL
—
MVREF – 0.25
V
AC input high voltage
VIH
MVREF + 0.25
—
V
Notes
Table 17 provides the input AC timing specifications for the DDR SDRAM when GVDD(typ)=2.5 V.
Table 17. DDR SDRAM Input AC Timing Specifications for 2.5-V Interface
At recommended operating conditions with GVDD of 2.5 ±5%.
Parameter
Symbol
Min
Max
Unit
AC input low voltage
VIL
—
MVREF – 0.31
V
AC input high voltage
VIH
MVREF + 0.31
—
V
Notes
Table 18 provides the input AC timing specifications for the DDR2 SDRAM interface.
Table 18. DDR and DDR2 SDRAM Input AC Timing Specifications
At recommended operating conditions. with GVDD of 2.5 ±5%
Parameter
Controller Skew for
MDQS—MDQ//MDM
Symbol
Min
Max
tCISKEW
333 MHz
–750
750
266 MHz
–750
750
200 MHz
–1250
1250
Unit
Notes
ps
1, 2
Note:
1. tCISKEW represents the total amount of skew consumed by the controller between MDQS[n] and any
corresponding bit that will be captured with MDQS[n]. This should be subtracted from the total timing budget.
2. The amount of skew that can be tolerated from MDQS to a corresponding MDQ signal is called tDISKEW. This
can be determined by the following equation: tDISKEW = +/–(T/4 – abs(tCISKEW)) where T is the clock period
and abs(tCISKEW) is the absolute value of tCISKEW.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
18
Freescale Semiconductor
DDR and DDR2 SDRAM
6.2.2
DDR and DDR2 SDRAM Output AC Timing Specifications
Table 19. DDR and DDR2 SDRAM Output AC Timing Specifications
At recommended operating conditions.
Parameter
MCK[n] cycle time, MCK[n]/MCK[n] crossing
ADDR/CMD output setup with respect to MCK
Symbol 1
Min
Max
Unit
Notes
tMCK
6
10
ns
2
ns
3
ns
3
ns
3
ns
3
ns
4
ps
5
ps
5
tDDKHAS
333 MHz
2.1
—
266 MHz
2.5
—
200 MHz
3.5
—
ADDR/CMD output hold with respect to MCK
tDDKHAX
333 MHz
2.40
—
266 MHz
3.15
—
200 MHz
4.20
—
MCS[n] output setup with respect to MCK
tDDKHCS
333 MHz
2.40
—
266 MHz
3.15
—
200 MHz
4.20
—
MCS[n] output hold with respect to MCK
tDDKHCX
333 MHz
2.40
—
266 MHz
3.15
—
200 MHz
4.20
—
–0.6
0.6
MCK to MDQS Skew
tDDKHMH
MDQ//MDM output setup with respect to MDQS
tDDKHDS,
tDDKLDS
333 MHz
800
—
266 MHz
900
—
200 MHz
1000
—
MDQ//MDM output hold with respect to MDQS
tDDKHDX,
tDDKLDX
333 MHz
900
—
266 MHz
1100
—
200 MHz
1200
—
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
19
DDR and DDR2 SDRAM
Table 19. DDR and DDR2 SDRAM Output AC Timing Specifications (continued)
At recommended operating conditions.
Symbol 1
Min
Max
Unit
Notes
MDQS preamble start
tDDKHMP
–0.5 × tMCK – 0.6
–0.5 × tMCK +0.6
ns
6
MDQS epilogue end
tDDKHME
–0.6
0.6
ns
6
Parameter
Note:
1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. Output hold time can be read as DDR timing
(DD) from the rising or falling edge of the reference clock (KH or KL) until the output went invalid (AX or DX). For example,
tDDKHAS symbolizes DDR timing (DD) for the time tMCK memory clock reference (K) goes from the high (H) state until
outputs (A) are setup (S) or output valid time. Also, tDDKLDX symbolizes DDR timing (DD) for the time tMCK memory clock
reference (K) goes low (L) until data outputs (D) are invalid (X) or data output hold time.
2. All MCK/MCK referenced measurements are made from the crossing of the two signals ±0.1 V.
3. ADDR/CMD includes all DDR SDRAM output signals except MCK/MCK, MCS, and MDQ//MDM/MDQS.
4. Note that tDDKHMH follows the symbol conventions described in note 1. For example, tDDKHMH describes the DDR timing (DD)
from the rising edge of the MCK[n] clock (KH) until the MDQS signal is valid (MH). tDDKHMH can be modified through control
of the DQSS override bits in the TIMING_CFG_2 register. This will typically be set to the same delay as the clock adjust in
the CLK_CNTL register. The timing parameters listed in the table assume that these 2 parameters have been set to the same
adjustment value. See the MPC8313E PowerQUICC II Pro Host Processor Reference Manual for a description and
understanding of the timing modifications enabled by use of these bits.
5. Determined by maximum possible skew between a data strobe (MDQS) and any corresponding bit of data (MDQ), ECC
(MECC), or data mask (MDM). The data strobe should be centered inside of the data eye at the pins of the microprocessor.
6. All outputs are referenced to the rising edge of MCK[n] at the pins of the microprocessor. Note that tDDKHMP follows the
symbol conventions described in note 1.
NOTE
For the ADDR/CMD setup and hold specifications in Table 19, it is
assumed that the clock control register is set to adjust the memory clocks by
1/2 applied cycle.
Figure 4 shows the DDR SDRAM output timing for the MCK to MDQS skew measurement (tDDKHMH).
MCK[n]
MCK[n]
tMCK
tDDKHMHmax) = 0.6 ns
MDQS
tDDKHMH(min) = –0.6 ns
MDQS
Figure 4. Timing Diagram for tDDKHMH
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
20
Freescale Semiconductor
DUART
Figure 5 shows the DDR and DDR2 SDRAM output timing diagram.
MCK[n]
MCK[n]
tMCK
tDDKHAS ,tDDKHCS
tDDKHAX ,tDDKHCX
ADDR/CMD
Write A0
NOOP
tDDKHMP
tDDKHMH
MDQS[n]
tDDKHME
tDDKHDS
tDDKLDS
MDQ[x]
D0
D1
tDDKLDX
tDDKHDX
Figure 5. DDR and DDR2 SDRAM Output Timing Diagram
Figure 6 provides the AC test load for the DDR bus.
Z0 = 50 Ω
Output
RL = 50 Ω
GVDD/2
Figure 6. DDR AC Test Load
7
DUART
This section describes the DC and AC electrical specifications for the DUART interface.
7.1
DUART DC Electrical Characteristics
Table 20 provides the DC electrical characteristics for the DUART interface.
Table 20. DUART DC Electrical Characteristics
Parameter
Symbol
Min
Max
Unit
High-level input voltage
VIH
2
NVDD + 0.3
V
Low-level input voltage NVDD
VIL
–0.3
0.8
V
High-level output voltage,
IOH = –100 μA
VOH
NVDD – 0.2
—
V
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
21
DUART
Table 20. DUART DC Electrical Characteristics (continued)
7.2
Low-level output voltage,
IOL = 100 μA
VOL
—
0.2
V
Input current
(0 V ≤VIN ≤ NVDD)
IIN
—
±5
μA
DUART AC Electrical Specifications
Table 21 provides the AC timing parameters for the DUART interface.
Table 21. DUART AC Timing Specifications
Parameter
Value
Unit
Minimum baud rate
256
baud
Maximum baud rate
> 1,000,000
baud
1
16
—
2
Oversample rate
Notes
Notes:
1. Actual attainable baud rate will be limited by the latency of interrupt processing.
2. The middle of a start bit is detected as the 8th sampled 0 after the 1-to-0 transition of the start bit. Subsequent bit
values are sampled each 16th sample.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
22
Freescale Semiconductor
Ethernet: Three-Speed Ethernet, MII Management
8
Ethernet: Three-Speed Ethernet, MII Management
This section provides the AC and DC electrical characteristics for three-speed, 10/100/1000, and MII
management.
8.1
Enhanced Three-Speed Ethernet Controller (eTSEC)
(10/100/1000 Mbps)—MII/RMII/RGMII/SGMII/RTBI Electrical
Characteristics
The electrical characteristics specified here apply to all the MII (media independent interface), RGMII
(reduced gigabit media independent interface), SGMII (serial gigabit media independent interface), and
RTBI (reduced ten-bit interface) signals except MDIO (management data input/output) and MDC
(management data clock). The MII interface is defined for 3.3V, while the RMII, RGMII, SGMII, and
RTBI interfaces can be operated at 3.3 or 2.5 V. The RGMII and RTBI interfaces follow the
Hewlett-Packard reduced pin-count interface for Gigabit Ethernet Physical Layer Device Specification
Version 1.2a (9/22/2000). The electrical characteristics for MDIO and MDC are specified in Section 8.3,
“Ethernet Management Interface Electrical Characteristics.”
8.1.1
TSEC DC Electrical Characteristics
All RGMII, SGMII, RMII, and RTBI drivers and receivers comply with the DC parametric attributes
specified in Table 22 and Table 23. The potential applied to the input of a MII, RGMII, SGMII, or RTBI
receiver may exceed the potential of the receiver’s power supply (that is, a RGMII driver powered from a
3.6-V supply driving VOH into a RGMII receiver powered from a 2.5-V supply). Tolerance for dissimilar
RGMII driver and receiver supply potentials is implicit in these specifications. The RGMII and RTBI
signals are based on a 2.5-V CMOS interface voltage as defined by JEDEC EIA/JESD8-5.
Table 22. MII/RGMII/RTBI (When Operating at 3.3V) DC Electrical Characteristics
Parameter
Symbol
Conditions
Min
Max
Unit
Supply voltage 3.3 V
LVDDA/LVDDB
—
2.97
3.63
V
Output high voltage
VOH
IOH = –4.0 mA
LVDDA or LV DDB = Min
2.40
LVDDA + 0.3
or
LVDDB + 0.3
V
Output low voltage
VOL
IOL = 4.0 mA
LVDDA or LVDDB = Min
VSS
0.50
V
Input high voltage
VIH
—
—
2.0
LVDDA + 0.3
or
LVDDB + 0.3
V
Input low voltage
VIL
—
—
–0.3
0.90
V
—
40
μA
–600
—
μA
Input high current
IIH
Input low current
IIL
VIN
1=
LVDDA or LVDDB
VIN 1 = VSS
Note:
1. The symbol V IN, in this case, represents the LVIN symbol referenced in Table 1 and Table 2.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
23
Ethernet: Three-Speed Ethernet, MII Management
Table 23. RGMII/RTBI (When Operating at 2.5 V) DC Electrical Characteristics
Parameters
Symbol
Conditions
Min
Max
Unit
Supply voltage 2.5 V
LVDDA/LVDDB
—
2.37
2.63
V
Output high voltage
VOH
IOH = –1.0 mA LVDDA or LV DDB = Min
2.00
LVDDA + 0.3
or
LVDDB + 0.3
V
Output low voltage
VOL
IOL = 1.0 mA
0.40
V
Input high voltage
VIH
—
Input low voltage
VIL
—
Input high current
IIH
Input low current
IIL
VIN
1=
LVDDA or LV DDB = Min VSS – 0.3
LVDDA or LV DDB = Min
1.7
LVDDA + 0.3
or
LVDDB + 0.3
V
LVDDA or LV DDB = Min
–0.3
0.70
V
—
10
μA
–15
—
μA
LVDDA or LVDDB
VIN 1 = VSS
Note:
1. Note that the symbol VIN, in this case, represents the LVIN symbol referenced in Table 1 and Table 2.
8.2
MII, RGMII, SGMII, and RTBI AC Timing Specifications
The AC timing specifications for MII, RMII, RGMII, SGMII, and RTBI are presented in this section.
8.2.1
MII AC Timing Specifications
This section describes the MII transmit and receive AC timing specifications.
8.2.1.1
MII Transmit AC Timing Specifications
Table 24 provides the MII transmit AC timing specifications.
Table 24. MII Transmit AC Timing Specifications
At recommended operating conditions with LVDDA/LVDDB /NVDD of 3.3 V ± 10%.
Symbol 1
Min
Typ
Max
Unit
TX_CLK clock period 10 Mbps
tMTX
—
400
—
ns
TX_CLK clock period 100 Mbps
tMTX
—
40
—
ns
tMTXH/tMTX
35
—
65
%
tMTKHDX
1
5
15
ns
Parameter/Condition
TX_CLK duty cycle
TX_CLK to MII data TXD[3:0], TX_ER, TX_EN delay
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
24
Freescale Semiconductor
Ethernet: Three-Speed Ethernet, MII Management
Table 24. MII Transmit AC Timing Specifications (continued)
At recommended operating conditions with LVDDA/LVDDB /NVDD of 3.3 V ± 10%.
Symbol 1
Min
Typ
Max
Unit
TX_CLK data clock rise VIL(min) to VIH(max)
tMTXR
1.0
—
4.0
ns
TX_CLK data clock fall VIH(max) to VIL(min)
tMTXF
1.0
—
4.0
ns
Parameter/Condition
Note:
1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state)
for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMTKHDX symbolizes MII
transmit timing (MT) for the time tMTX clock reference (K) going high (H) until data outputs (D) are invalid (X). Note that, in
general, the clock reference symbol representation is based on two to three letters representing the clock of a particular
functional. For example, the subscript of tMTX represents the MII(M) transmit (TX) clock. For rise and fall times, the latter
convention is used with the appropriate letter: R (rise) or F (fall).
Figure 7 shows the MII transmit AC timing diagram.
tMTXR
tMTX
TX_CLK
tMTXH
tMTXF
TXD[3:0]
TX_EN
TX_ER
tMTKHDX
Figure 7. MII Transmit AC Timing Diagram
8.2.1.2
MII Receive AC Timing Specifications
Table 25 provides the MII receive AC timing specifications.
Table 25. MII Receive AC Timing Specifications
At recommended operating conditions with LVDDA/LVDDB /NVDD of 3.3 V ± 10%.
Symbol 1
Min
Typ
Max
Unit
RX_CLK clock period 10 Mbps
tMRX
—
400
—
ns
RX_CLK clock period 100 Mbps
tMRX
—
40
—
ns
tMRXH/tMRX
35
—
65
%
RXD[3:0], RX_DV, RX_ER setup time to RX_CLK
tMRDVKH
10.0
—
—
ns
RXD[3:0], RX_DV, RX_ER hold time to RX_CLK
tMRDXKH
10.0
—
—
ns
Parameter/Condition
RX_CLK duty cycle
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
25
Ethernet: Three-Speed Ethernet, MII Management
Table 25. MII Receive AC Timing Specifications (continued)
At recommended operating conditions with LVDDA/LVDDB /NVDD of 3.3 V ± 10%.
Symbol 1
Min
Typ
Max
Unit
RX_CLK clock rise VIL(min) to VIH(max)
tMRXR
1.0
—
4.0
ns
RX_CLK clock fall time VIH(max) to VIL(min)
tMRXF
1.0
—
4.0
ns
Parameter/Condition
Note:
1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state)
for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMRDVKH symbolizes MII
receive timing (MR) with respect to the time data input signals (D) reach the valid state (V) relative to the tMRX clock reference
(K) going to the high (H) state or setup time. Also, tMRDXKL symbolizes MII receive timing (GR) with respect to the time data
input signals (D) went invalid (X) relative to the tMRX clock reference (K) going to the low (L) state or hold time. Note that, in
general, the clock reference symbol representation is based on three letters representing the clock of a particular functional.
For example, the subscript of tMRX represents the MII (M) receive (RX) clock. For rise and fall times, the latter convention is
used with the appropriate letter: R (rise) or F (fall).
Figure 8 provides the AC test load for TSEC.
Output
Z0 = 50 Ω
RL = 50 Ω
LVDDA/2 or LVDDB/2
Figure 8. TSEC AC Test Load
Figure 9 shows the MII receive AC timing diagram.
tMRX
tMRXR
RX_CLK
tMRXH
RXD[3:0]
RX_DV
RX_ER
tMRXF
Valid Data
tMRDVKH
tMRDXKH
Figure 9. MII Receive AC Timing Diagram RMII AC Timing Specifications
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
26
Freescale Semiconductor
Ethernet: Three-Speed Ethernet, MII Management
8.2.1.3
RMII Transmit AC Timing Specifications
This section describes the RMII transmit and receive AC timing specifications.
Table 26 provides the RMII transmit AC timing specifications.
Table 26. RMII Transmit AC Timing Specifications
At recommended operating conditions with NVDD of 3.3 V ± 10%.
Symbol 1
Min
Typical
Max
Unit
tRMX
—
20
—
ns
tRMXH/tRMX
35
—
65
%
REF_CLK to RMII data TXD[1:0], TX_EN delay
tRMTKHDX
2
-
10
ns
REF_CLK data clock rise VIL(min) to V IH(max)
tRMXR
1.0
—
4.0
ns
REF_CLK data clock fall VIH(max) to VIL(min)
tRMXF
1.0
—
4.0
ns
Parameter/Condition
REF_CLK clock
REF_CLK duty cycle
Note:
1. The symbols used for timing specifications herein follow the pattern of t(first three letters of functional block)(signal)(state)
(reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tRMTKHDX
symbolizes RMII transmit timing (RMT) for the time tRMX clock reference (K) going high (H) until data outputs (D) are invalid
(X). Note that, in general, the clock reference symbol representation is based on two to three letters representing the clock
of a particular functional. For example, the subscript of tRMX represents the RMII(RM) reference (X) clock. For rise and fall
times, the latter convention is used with the appropriate letter: R (rise) or F (fall).
Figure 10 shows the RMII transmit AC timing diagram.
tRMXR
tRMX
REF_CLK
tRMXH
tRMXF
TXD[1:0]
TX_EN
tRMTKHDX
Figure 10. RMII Transmit AC Timing Diagram
8.2.1.4
RMII Receive AC Timing Specifications
Table 27 provides the RMII receive AC timing specifications.
Table 27. RMII Receive AC Timing Specifications
At recommended operating conditions with NVDD of 3.3 V ± 10%.
Symbol 1
Min
Typical
Max
Unit
tRMX
—
20
—
ns
tRMXH/tRMX
35
—
65
%
RXD[1:0], CRS_DV, RX_ER setup time to REF_CLK
tRMRDVKH
4.0
—
—
ns
RXD[1:0], CRS_DV, RX_ER hold time to REF_CLK
tRMRDXKH
2.0
—
—
ns
Parameter/Condition
REF_CLK clock period
REF_CLK duty cycle
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
27
Ethernet: Three-Speed Ethernet, MII Management
Table 27. RMII Receive AC Timing Specifications (continued)
At recommended operating conditions with NVDD of 3.3 V ± 10%.
Symbol 1
Min
Typical
Max
Unit
REF_CLK clock rise VIL(min) to VIH(max)
tRMXR
1.0
—
4.0
ns
REF_CLK clock fall time VIH(max) to VIL(min)
tRMXF
1.0
—
4.0
ns
Parameter/Condition
Note:
1. The symbols used for timing specifications herein follow the pattern of t(first three letters of functional block)(signal)(state)
(reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tRMRDVKH
symbolizes RMII receive timing (RMR) with respect to the time data input signals (D) reach the valid state (V) relative to the
tRMX clock reference (K) going to the high (H) state or setup time. Also, tRMRDXKL symbolizes RMII receive timing (RMR) with
respect to the time data input signals (D) went invalid (X) relative to the tRMX clock reference (K) going to the low (L) state or
hold time. Note that, in general, the clock reference symbol representation is based on three letters representing the clock
of a particular functional. For example, the subscript of tRMX represents the RMII (RM) reference (X) clock. For rise and fall
times, the latter convention is used with the appropriate letter: R (rise) or F (fall).
Figure 11 provides the AC test load.
Z0 = 50 Ω
Output
RL = 50 Ω
NVDD/2
Figure 11. AC Test Load
Figure 12 shows the RMII receive AC timing diagram.
tRMX
tRMXR
REF_CLK
tRMXF
tRMXH
RXD[1:0]
CRS_DV
RX_ER
Valid Data
tRMRDVKH
tRMRDXKH
Figure 12. RMII Receive AC Timing Diagram
8.2.2
RGMII and RTBI AC Timing Specifications
Table 28 presents the RGMII and RTBI AC timing specifications.
Table 28. RGMII and RTBI AC Timing Specifications
At recommended operating conditions with LVDDA/LVDDB of 2.5 V ± 5%.
Parameter/Condition
Data to clock output skew (at transmitter)
Data to clock input skew (at receiver)
Clock cycle duration
3
2
Symbol 1
Min
Typ
Max
Unit
tSKRGT
–0.5
—
0.5
ns
tSKRGT
1.0
—
2.8
ns
tRGT
7.2
8.0
8.8
ns
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
28
Freescale Semiconductor
Ethernet: Three-Speed Ethernet, MII Management
Table 28. RGMII and RTBI AC Timing Specifications (continued)
At recommended operating conditions with LVDDA/LVDDB of 2.5 V ± 5%.
Duty cycle for 1000Base-T 4, 5
tRGTH/tRGT
45
50
55
%
tRGTH/tRGT
40
50
60
%
Rise time (20%–80%)
tRGTR
—
—
0.75
ns
Fall time (20%–80%)
tRGTF
—
—
0.75
ns
6
—
8.0
—
ns
47
—
53
%
Duty cycle for 10BASE-T and 100BASE-TX
3, 5
GTX_CLK125 reference clock period
tG12
tG125H/tG125
GTX_CLK125 reference clock duty cycle
Notes:
1. Note that, in general, the clock reference symbol representation for this section is based on the symbols RGT to represent
RGMII and RTBI timing. For example, the subscript of tRGT represents the RTBI (T) receive (RX) clock. Note also that the
notation for rise (R) and fall (F) times follows the clock symbol that is being represented. For symbols representing skews,
the subscript is skew (SK) followed by the clock that is being skewed (RGT).
2. This implies that PC board design will require clocks to be routed such that an additional trace delay of greater than 1.5 ns
will be added to the associated clock signal.
3. For 10 and 100 Mbps, tRGT scales to 400 ns ± 40 ns and 40 ns ± 4 ns, respectively.
4. Duty cycle may be stretched/shrunk during speed changes or while transitioning to a received packet's clock domains as long
as the minimum duty cycle is not violated and stretching occurs for no more than three tRGT of the lowest speed transitioned
between.
5. Duty cycle reference is LVDDA/2 or LVDDB/2.
6. This symbol is used to represent the external GTX_CLK125 and does not follow the original symbol naming convention.
Figure 13 shows the RGMII and RTBI AC timing and multiplexing diagrams.
tRGT
tRGTH
GTX_CLK
(At Transmitter)
tSKRGT
TXD[8:5][3:0]
TXD[7:4][3:0]
TX_CTL
TXD[8:5]
TXD[3:0] TXD[7:4]
TXD[4]
TXEN
TXD[9]
TXERR
tSKRGT
TX_CLK
(At PHY)
RXD[8:5][3:0]
RXD[7:4][3:0]
RXD[8:5]
RXD[3:0] RXD[7:4]
tSKRGT
RX_CTL
RXD[4]
RXDV
RXD[9]
RXERR
tSKRGT
RX_CLK
(At PHY)
Figure 13. RGMII and RTBI AC Timing and Multiplexing Diagrams
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
29
Ethernet: Three-Speed Ethernet, MII Management
8.3
Ethernet Management Interface Electrical Characteristics
The electrical characteristics specified here apply to MII management interface signals MDIO
(management data input/output) and MDC (management data clock). The electrical characteristics for
MII, RMII, RGMII, SGMII, and RTBI are specified in Section 8.1, “Enhanced Three-Speed Ethernet
Controller (eTSEC) (10/100/1000 Mbps)—MII/RMII/RGMII/SGMII/RTBI Electrical Characteristics.”
8.3.1
MII Management DC Electrical Characteristics
The MDC and MDIO are defined to operate at a supply voltage of 2.5V or 3.3 V. The DC electrical
characteristics for MDIO and MDC are provided in Table 29 and Table 30.
Table 29. MII Management DC Electrical Characteristics When Powered at 2.5 V
Parameter
Symbol
Conditions
Min
Max
Unit
—
2.37
2.63
V
Supply voltage (2.5 V) NV DDA/NVDDB
Output high voltage
VOH
IOH = –1.0 mA
NVDDA or NV DDB = Min
2.00
NVDDA + 0.3
or
NVDDB + 0.3
V
Output low voltage
VOL
IOL = 1.0 mA
NVDDA or NV DDB = Min
VSS – 0.3
0.40
V
Input high voltage
VIH
—
NVDDA or NV DDB = Min
1.7
—
V
Input low voltage
VIL
—
NVDDA or NV DDB = Min
–0.3
0.70
V
Input high current
IIH
VIN 1 = NVDDA or NVDDB
—
10
μA
Input low current
IIL
VIN = NVDDA or NV DDB
–15
—
μA
Note:
1. Note that the symbol VIN, in this case, represents the LVIN symbol referenced in Table 1 and Table 2.
Table 30. MII Management DC Electrical Characteristics When Powered at 3.3 V
Parameter
Symbol
Conditions
Min
Max
Unit
—
2.97
3.63
V
Supply voltage (3.3 V) NVDDA/NVDDB
Output high voltage
VOH
IOH = –1.0 mA
NVDDA or NVDDB = Min
2.10
NVDDA + 0.3
or
NVDDB + 0.3
V
Output low voltage
VOL
IOL = 1.0 mA
LVDDA or LVDDB = Min
VSS
0.50
V
Input high voltage
VIH
—
2.00
—
V
Input low voltage
VIL
—
—
0.80
V
Input high current
IIH
NVDDA or NVDDB = Max
VIN 1 = 2.1 V
—
40
μA
Input low current
IIL
NVDDA or NVDDB = Max
VIN = 0.5 V
–600
—
μA
Note:
1. Note that the symbol VIN, in this case, represents the LVIN symbol referenced in Table 1 and Table 2.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
30
Freescale Semiconductor
Ethernet: Three-Speed Ethernet, MII Management
8.3.2
MII Management AC Electrical Specifications
Table 31 provides the MII management AC timing specifications.
Table 31. MII Management AC Timing Specifications
At recommended operating conditions with LVDDA/LVDDB is 3.3 V ± 10% or 2.5 V ± 5%
Symbol 1
Min
Typ
Max
Unit
Notes
MDC frequency
fMDC
—
2.5
—
MHz
2
MDC period
tMDC
—
400
—
ns
MDC clock pulse width high
tMDCH
32
—
—
ns
MDC to MDIO delay
tMDKHDX
10
—
170
ns
MDIO to MDC setup time
tMDDVKH
5
—
—
ns
MDIO to MDC hold time
tMDDXKH
0
—
—
ns
MDC rise time
tMDCR
—
—
10
ns
MDC fall time
tMDHF
—
—
10
ns
Parameter/Condition
Notes:
1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state)
for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMDKHDX symbolizes
management data timing (MD) for the time tMDC from clock reference (K) high (H) until data outputs (D) are invalid (X) or data
hold time. Also, tMDDVKH symbolizes management data timing (MD) with respect to the time data input signals (D) reach the
valid state (V) relative to the tMDC clock reference (K) going to the high (H) state or setup time. For rise and fall times, the
latter convention is used with the appropriate letter: R (rise) or F (fall).
Figure 14 shows the MII management AC timing diagram.
tMDCR
tMDC
MDC
tMDCF
tMDCH
MDIO
(Input)
tMDDVKH
tMDDXKH
MDIO
(Output)
tMDKHDX
Figure 14. MII Management Interface Timing Diagram
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
31
Ethernet: Three-Speed Ethernet, MII Management
8.3.3
SGMII DC Electrical Characteristics
The SGMII Solution in the MPC8313 is designed to be used in a 4-wire AC-Coupled SGMII link. Table 32
andTable 33describe the SGMII AC-Coupled DC electrical characteristics. Transmitter characteristics are
measured at the transmitter outputs, SD_TX and SD_TX_B as depicted in Figure 15.
Table 32. DC Transmitter Electrical Characteristics
Parameter
Symbol
Output high voltage
VOH
Output low voltage
VOL
Output ringing
VRING
Output differential voltage
|VOD|
Output offset voltage
VOS
Output impedance
(single ended)
RO
Mismatch in a pair
Min
Max
Unit
0.7*XPADVDD1
mV
0.3*XPADVDD
(XPADVDD/2)/1.7
mV
10
%
(XPADVDD/2)/1.3
mV
(XPADVDD/2) – 50 mV (XPADVDD/2) + 50 mV
mV
60
Ω
ΔRO
10
%
Change in VOD between “0” and “1”
Δ|VOD|
25
mV
Change in VOS between “0” and “1”
Δ VOS
25
mV
Output current on short to GND
ISA, ISB
40
mA
1 XPADVDDrefers
40
Notes
Will not align to
DC-coupled
SGMII
Will not align to
DC-coupled
SGMII
to the SGMII transmitter output supply voltage.
SD_TX
Transmitter
100 ohms
SD_TX_B
Figure 15. Transmitter Reference Circuit
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
32
Freescale Semiconductor
Ethernet: Three-Speed Ethernet, MII Management
Table 33. DC Receiver Electrical Characteristics
Parameter
Symbol
Min
Max
Unit
DC input voltage range
Notes
Input must be externally ac-coupled.
Input differential voltage
Vrx_diffpp
100
1200
mV Peak to peak input differential
voltage.
Loss of signal threshold
Vlos
30
100
mV
100
mV Peak to peak ac common mode
voltage.
Input AC common mode voltage
Vcm_acpp
Receiver differential input impedance
Zrx_diff
80
120
Ω
Receiver common mode input impedance
Zrx_cm
20
35
Ω
Vcm
xcorevss
xcorevss
V
Common mode input voltage
8.3.3.1
On-chip termination to xcorevss.
SGMII Transmit AC Timing Specifications
Table 34 provides the SGMII transmit AC timing targets. A source synchronous clock is not provided.
Table 34. SGMII Transmit AC Timing Specifications
Parameter
Symbol
Min
Max
Unit
Deterministic Jitter
JD
0.17
UI p-p
Total Jitter
JT
0.35
UI p-p
Unit Interval
UI
800
800
ps
VOD fall time (80%–20%)
tfall
50
120
ps
VOD rise time (20%–80%)
trise
50
120
ps
Notes
+/– 100ppm
Source synchronous clock is not supported
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
33
Ethernet: Three-Speed Ethernet, MII Management
8.3.3.2
SGMII Receive AC Timing Specifications
Table 35 provides the SGMII transmit AC timing targets. A source synchronous clock is not supported.
Table 35. SGMII Receiver AC Timing Specifications
Parameter
Symbol
Min
Deterministic Jitter
Tolerance
JD
0.37
UI p-p
Measured at receiver
Combined Deterministic
and
Random Jitter Tolerance
JDR
0.55
UI p-p
Measured at receiver
Sinusoidal Jitter Tolerance
Jsin
0.1
UI p-p
Measured at receiver
JT
0.65
UI p-p
Measured at receiver
Total Jitter Tolerance
Bit Error Ratio
Unit Interval
Max
Unit
Notes
10-12
BER
UI
800
800
ps
+/– 100ppm
Vrx_diffpp_max/2
Vrx_diffpp_min/2
0
–Vrx_diffpp_min/2
–Vrx_diffpp_max/2
0
.275
.4
.6
Time (UI)
.625
1
Figure 16. Receive Input Compliance Mask
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
34
Freescale Semiconductor
USB
9
9.1
USB
USB Dual-Role Controllers
This section provides the AC and DC electrical specifications for the USB interface.
9.1.1
USB DC Electrical Characteristics
Table 36 provides the DC electrical characteristics for the USB interface.
Table 36. USB DC Electrical Characteristics
Parameter
Symbol
Min
Max
Unit
High-level input voltage
VIH
2
LVDDB+ 0.3
V
Low-level input voltage
VIL
–0.3
0.8
V
Input current
IIN
—
±5
μA
High-level output voltage,
IOH = –100 μA
VOH
LV DDB – 0.2
—
V
Low-level output voltage,
IOL = 100 μA
VOL
—
0.2
V
9.1.2
USB AC Electrical Specifications
Table 37 describes the general timing parameters of the USB interface.
Table 37. USB General Timing Parameters
Symbol 1
Min
Max
Unit
tUSCK
15
—
ns
Input setup to USB clock - all inputs
tUSIVKH
4
—
ns
input hold to USB clock - all inputs
tUSIXKH
0
—
ns
USB clock to output valid - all outputs
tUSKHOV
—
7
ns
Output hold from USB clock - all outputs
tUSKHOX
2
—
ns
Parameter
USB clock cycle time
Notes
Note:
1. The symbols used for timing specifications herein follow the pattern of t(First two letters of functional block)(signal)(state) (reference)(state)
for inputs and t(First two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tUSIXKH symbolizes USB
timing (USB) for the input (I) to go invalid (X) with respect to the time the USB clock reference (K) goes high (H). Also, t USKHOX
symbolizes us timing (USB) for the USB clock reference (K) to go high (H), with respect to the output (O) going invalid (X) or
output hold time.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
35
USB
Figure 17 and Figure 18 provide the AC test load and signals for the USB, respectively.
Output
Z0 = 50 Ω
RL = 50 Ω
NVDD/2
Figure 17. USB AC Test Load
USB0_CLK/USB1_CLK/DR_CLK
tUSIVKH
tUSIXKH
Input Signals
tUSKHOV
tUSKHOX
Output Signals:
Figure 18. USB Signals
9.2
On-Chip USB PHY
See chapter 7 in the USB Specifications Rev 2.0
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
36
Freescale Semiconductor
Local Bus
10 Local Bus
This section describes the DC and AC electrical specifications for the local bus interface.
10.1 Local Bus DC Electrical Characteristics
Table 38 provides the DC electrical characteristics for the local bus interface.
Table 38. Local Bus DC Electrical Characteristics at 3.3 V
Parameter
10.2
Symbol
Min
Max
Unit
High-level input voltage
VIH
2
LVDD + 0.3
V
Low-level input voltage
VIL
–0.3
0.8
V
Input current
(VIN1 = 0 V or VIN = LV DD)
IIN
—
±5
μA
High-level output voltage,
(LVDD = min, IOH = -2 mA)
VOH
LVDD – 0.2
—
V
Low-level output voltage,
(LVDD = min, IOH = 2 mA)
VOL
—
0.2
V
Local Bus AC Electrical Specifications
Table 39 describes the general timing parameters of the local bus interface.
Table 39. Local Bus General Timing Parameters
Symbol 1
Min
Max
Unit
Notes
tLBK
15
—
ns
2
Input setup to local bus clock
tLBIVKH
7
—
ns
3, 4
Input hold from local bus clock
tLBIXKH
1.0
—
ns
3, 4
LALE output fall to LAD output transition (LATCH hold time)
tLBOTOT1
1.5
—
ns
5
LALE output fall to LAD output transition (LATCH hold time)
tLBOTOT2
3
—
ns
6
LALE output fall to LAD output transition (LATCH hold time)
tLBOTOT3
2.5
—
ns
7
Parameter
Local bus cycle time
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
37
Local Bus
Table 39. Local Bus General Timing Parameters (continued)
Symbol 1
Min
Max
Unit
Notes
Local bus clock to output valid
tLBKHOV
—
3
ns
3
Local bus clock to output high impedance for LAD
tLBKHOZ
—
4
ns
8
Parameter
Notes:
1. The symbols used for timing specifications herein follow the pattern of t(First two letters of functional block)(signal)(state) (reference)(state)
for inputs and t(First two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tLBIXKH1 symbolizes local
bus timing (LB) for the input (I) to go invalid (X) with respect to the time the tLBK clock reference (K) goes high (H), in this
case for clock one(1).
2. All timings are in reference to falling edge of LCLK0 (for all outputs and for LGTA and LUPWAIT inputs) or rising edge of
LCLK0 (for all other inputs).
3. All signals are measured from NVDD/2 of the rising/falling edge of LCLK0 to 0.4 × NVDD of the signal in question for 3.3-V
signaling levels.
4. Input timings are measured at the pin.
5.tLBOTOT1 should be used when RCWH[LALE] is not set and the load on LALE output pin is at least 10pF less than the load
on LAD output pins.
6.tLBOTOT2 should be used when RCWH[LALE] is set and the load on LALE output pin is at least 10pF less than the load on
LAD output pins.
7.tLBOTOT3 should be used when RCWH[LALE] is set and the load on LALE output pin equals to the load on LAD output pins.
8. For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered
through the component pin is less than or equal to the leakage current specification.
Figure 19 provides the AC test load for the local bus.
Output
Z0 = 50 Ω
RL = 50 Ω
NVDD/2
Figure 19. Local Bus AC Test Load
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
38
Freescale Semiconductor
Local Bus
Figure 20 through Figure 22 show the local bus signals.
LCLK[n]
tLBIVKH
Input Signals:
LAD[0:15]
tLBIXKH
tLBIXKH
tLBIVKH
Input Signal:
LGTA
tLBIXKH
Output Signals:
LBCTL/LBCKE/LOE/
tLBKHOV
tLBKHOV
tLBKHOZ
Output Signals:
LAD[0:15]
tLBOTOT
LALE
Figure 20. Local Bus Signals, Non-Special Signals Only
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
39
Local Bus
LCLK
T1
T3
tLBKHOV
tLBKHOZ
GPCM Mode Output Signals:
LCS[0:3]/LWE
tLBIVKH
tLBIXKH
UPM Mode Input Signal:
LUPWAIT
tLBIXKH
tLBIVKH
Input Signals:
LAD[0:15]
tLBKHOV
tLBKHOZ
UPM Mode Output Signals:
LCS[0:3]/LBS[0:1]/LGPL[0:5]
Figure 21. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 2
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
40
Freescale Semiconductor
Local Bus
LCLK
T1
T2
T3
T4
tLBKHOV
tLBKHOZ
GPCM Mode Output Signals:
LCS[0:3]/LWE
tLBIVKH
tLBIXKH
UPM Mode Input Signal:
LUPWAIT
tLBIVKH
Input Signals:
LAD[0:15]
tLBKHOV
tLBIXKH
tLBKHOZ
UPM Mode Output Signals:
LCS[0:3]/LBS[0:1]/LGPL[0:5]
Figure 22. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 4
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
41
JTAG
11 JTAG
This section describes the DC and AC electrical specifications for the IEEE Std. 1149.1 (JTAG) interface.
11.1
JTAG DC Electrical Characteristics
Table 40 provides the DC electrical characteristics for the IEEE Std. 1149.1 (JTAG) interface.
Table 40. JTAG Interface DC Electrical Characteristics
Characteristic
11.2
Symbol
Condition
Min
Max
Unit
Input high voltage
VIH
2.0
NVDD + 0.3
V
Input low voltage
VIL
–0.3
0.8
V
Input current
IIN
±5
μA
Output high voltage
VOH
IOH = –8.0 mA
2.4
—
V
Output low voltage
VOL
IOL = 8.0 mA
—
0.5
V
Output low voltage
VOL
IOL = 3.2 mA
—
0.4
V
JTAG AC Timing Specifications
This section describes the AC electrical specifications for the IEEE Std. 1149.1 (JTAG) interface.
Table 41 provides the JTAG AC timing specifications as defined in Figure 24 through Figure 27.
Table 41. JTAG AC Timing Specifications (Independent of SYS_CLK_IN) 1
At recommended operating conditions (see Table 2).
Symbol 2
Min
Max
Unit
JTAG external clock frequency of operation
fJTG
0
33.3
MHz
JTAG external clock cycle time
t JTG
30
—
ns
tJTKHKL
15
—
ns
tJTGR & tJTGF
0
2
ns
tTRST
25
—
ns
Boundary-scan data
TMS, TDI
tJTDVKH
tJTIVKH
4
4
—
—
Boundary-scan data
TMS, TDI
tJTDXKH
tJTIXKH
10
10
—
—
Boundary-scan data
TDO
tJTKLDV
tJTKLOV
2
2
11
11
Boundary-scan data
TDO
tJTKLDX
tJTKLOX
2
2
—
—
Parameter
JTAG external clock pulse width measured at 1.4 V
JTAG external clock rise and fall times
TRST assert time
Input setup times:
Notes
3
ns
4
ns
Input hold times:
4
ns
Valid times:
5
Output hold times:
ns
5
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
42
Freescale Semiconductor
JTAG
Table 41. JTAG AC Timing Specifications (Independent of SYS_CLK_IN) 1 (continued)
At recommended operating conditions (see Table 2).
Parameter
Symbol 2
Min
Max
Unit
Notes
JTAG external clock to output high impedance:
Boundary-scan data
TDO
tJTKLDZ
tJTKLOZ
2
2
19
9
ns
5, 6
Notes:
1. All outputs are measured from the midpoint voltage of the falling/rising edge of tTCLK to the midpoint of the signal in question.
The output timings are measured at the pins. All output timings assume a purely resistive 50-Ω load (see Figure 17).
Time-of-flight delays must be added for trace lengths, vias, and connectors in the system.
2. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state)
for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tJTDVKH symbolizes JTAG
device timing (JT) with respect to the time data input signals (D) reaching the valid state (V) relative to the tJTG clock
reference (K) going to the high (H) state or setup time. Also, tJTDXKH symbolizes JTAG timing (JT) with respect to the time
data input signals (D) went invalid (X) relative to the tJTG clock reference (K) going to the high (H) state. Note that, in general,
the clock reference symbol representation is based on three letters representing the clock of a particular functional. For rise
and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall).
3. TRST is an asynchronous level sensitive signal. The setup time is for test purposes only.
4. Non-JTAG signal input timing with respect to tTCLK.
5. Non-JTAG signal output timing with respect to tTCLK.
6. Guaranteed by design and characterization.
Figure 23 provides the AC test load for TDO and the boundary-scan outputs.
Z0 = 50 Ω
Output
R L = 50 Ω
NVDD/2
Figure 23. AC Test Load for the JTAG Interface
Figure 24 provides the JTAG clock input timing diagram.
JTAG
External Clock
VM
VM
VM
tJTGR
tJTKHKL
tJTGF
tJTG
VM = Midpoint Voltage (NV DD/2)
Figure 24. JTAG Clock Input Timing Diagram
Figure 25 provides the TRST timing diagram.
TRST
VM
VM
tTRST
VM = Midpoint Voltage (NVDD/2)
Figure 25. TRST Timing Diagram
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
43
JTAG
Figure 26 provides the boundary-scan timing diagram.
JTAG
External Clock
VM
VM
tJTDVKH
tJTDXKH
Boundary
Data Inputs
Input
Data Valid
tJTKLDV
tJTKLDX
Boundary
Data Outputs
Output Data Valid
tJTKLDZ
Boundary
Data Outputs
Output Data Valid
VM = Midpoint Voltage (NVDD /2)
Figure 26. Boundary-Scan Timing Diagram
Figure 27 provides the test access port timing diagram.
JTAG
External Clock
VM
VM
tJTIVKH
tJTIXKH
Input
Data Valid
TDI, TMS
tJTKLOV
tJTKLOX
Output Data Valid
TDO
tJTKLOZ
TDO
Output Data Valid
VM = Midpoint Voltage (NVDD/2)
Figure 27. Test Access Port Timing Diagram
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
44
Freescale Semiconductor
I2C
12 I2C
This section describes the DC and AC electrical characteristics for the I2C interface.
12.1
I2C DC Electrical Characteristics
Table 42 provides the DC electrical characteristics for the I2C interface.
Table 42. I2C DC Electrical Characteristics
At recommended operating conditions with NVDD of 3.3 V ± 10%.
Parameter
Symbol
Min
Max
Unit
Notes
Input high voltage level
VIH
0.7 × NVDD
NVDD + 0.3
V
Input low voltage level
VIL
–0.3
0.3 × NVDD
V
Low level output voltage
VOL
0
0.2 × NVDD
V
1
Output fall time from VIH(min) to VIL(max) with a bus
capacitance from 10 to 400 pF
tI2KLKV
20 + 0.1 × CB
250
ns
2
Pulse width of spikes which must be suppressed by the input
filter
tI2KHKL
0
50
ns
3
Capacitance for each I/O pin
CI
—
10
pF
Input current
(0 V ≤VIN ≤ NVDD)
IIN
—
±5
μA
4
Notes:
1. Output voltage (open drain or open collector) condition = 3 mA sink current.
2. CB = capacitance of one bus line in pF.
3. Refer to the MPC8313E PowerQUICC II Pro Integrated Host Processor Reference Manual for information on the digital filter
used.
4. I/O pins will obstruct the SDA and SCL lines if NVDD is switched off.
12.2
I2C AC Electrical Specifications
Table 43 provides the AC timing parameters for the I2C interface.
Table 43. I2C AC Electrical Specifications
All values refer to VIH (min) and VIL (max) levels (see Table 42).
Symbol 1
Min
Max
Unit
SCL clock frequency
fI2C
0
400
kHz
Low period of the SCL clock
tI2CL
1.3
—
μs
High period of the SCL clock
tI2CH
0.6
—
μs
Setup time for a repeated START condition
tI2SVKH
0.6
—
μs
Hold time (repeated) START condition (after this period, the first clock
pulse is generated)
tI2SXKL
0.6
—
μs
Data setup time
tI2DVKH
100
—
ns
Parameter
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
45
I2C
Table 43. I2C AC Electrical Specifications (continued)
All values refer to VIH (min) and VIL (max) levels (see Table 42).
Symbol 1
Parameter
Min
Max
—
02
—
0.9 3
μs
tI2DXKL
Data hold time:
CBUS compatible masters
I2C bus devices
Rise time of both SDA and SCL signals
Fall time of both SDA and SCL signals
Unit
tI2CR
20 + 0.1 CB 4
300
ns
tI2CF
4
300
ns
20 + 0.1 CB
Setup time for STOP condition
tI2PVKH
0.6
—
μs
Bus free time between a STOP and START condition
tI2KHDX
1.3
—
μs
Noise margin at the LOW level for each connected device (including
hysteresis)
VNL
0.1 × NVDD
—
V
Noise margin at the HIGH level for each connected device (including
hysteresis)
VNH
0.2 × NVDD
—
V
Notes:
1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state)
for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tI2DVKH symbolizes I2C timing
(I2) with respect to the time data input signals (D) reach the valid state (V) relative to the tI2C clock reference (K) going to the
high (H) state or setup time. Also, tI2SXKL symbolizes I2C timing (I2) for the time that the data with respect to the start condition
(S) went invalid (X) relative to the tI2C clock reference (K) going to the low (L) state or hold time. Also, tI2PVKH symbolizes I2C
timing (I2) for the time that the data with respect to the stop condition (P) reaching the valid state (V) relative to the tI2C clock
reference (K) going to the high (H) state or setup time. For rise and fall times, the latter convention is used with the appropriate
letter: R (rise) or F (fall).
2. The MPC8313E provides a hold time of at least 300 ns for the SDA signal (referred to the VIHmin of the SCL signal) to bridge
the undefined region of the falling edge of SCL.
3. The maximum tI2DVKH has only to be met if the device does not stretch the LOW period (tI2CL) of the SCL signal.
4. CB = capacitance of one bus line in pF.
Figure 28 provides the AC test load for the I2C.
Output
Z0 = 50 Ω
RL = 50 Ω
NVDD/2
Figure 28. I2C AC Test Load
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
46
Freescale Semiconductor
I2C
Figure 29 shows the AC timing diagram for the I2C bus.
SDA
tI2CF
tI2DVKH
tI2CL
tI2KHKL
tI2SXKL
tI2CF
tI2CR
SCL
tI2SXKL
tI2CH
tI2DXKL
S
tI2SVKH
Sr
tI2PVKH
P
S
Figure 29. I2C Bus AC Timing Diagram
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
47
PCI
13 PCI
This section describes the DC and AC electrical specifications for the PCI bus.
13.1
PCI DC Electrical Characteristics
Table 44 provides the DC electrical characteristics for the PCI interface.
Table 44. PCI DC Electrical Characteristics 1
Parameter
Symbol
Test Condition
Min
Max
Unit
High-level input voltage
VIH
VOUT ≥ VOH (min) or
0.5 x NVDD
NVDD + 0.3
V
Low-level input voltage
VIL
VOUT ≤ VOL (max)
–0.5
0.3 x NVDD
V
High-level output voltage
VOH
NVDD = min,
IOH = –100 μA
0.9 x NVDD
—
V
Low-level output voltage
VOL
NVDD = min,
IOL = 100 μA
—
0.1x NVDD
V
IIN
0 V ≤ VIN ≤ NVDD
—
±5
μA
Input current
Note:
1. Note that the symbol V IN, in this case, represents the OVIN symbol referenced in Table 1 and Table 2.
13.2
PCI AC Electrical Specifications
This section describes the general AC timing parameters of the PCI bus. Note that the PCI_CLK or
PCI_SYNC_IN signal is used as the PCI input clock depending on whether the MPC8313E is configured
as a host or agent device.
Table 45 shows the PCI AC timing specifications at 66 MHz.
.
Table 45. PCI AC Timing Specifications at 66 MHz
Symbol 1
Min
Max
Unit
Notes
Clock to output valid
tPCKHOV
—
6.0
ns
2
Output hold from Clock
tPCKHOX
1
—
ns
2
Clock to output high impedance
tPCKHOZ
—
14
ns
2, 3
Input setup to Clock
tPCIVKH
3.0
—
ns
2, 4
Input hold from Clock
tPCIXKH
0
—
ns
2, 4
Parameter
Notes:
1. Note that the symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state)
(reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tPCIVKH
symbolizes PCI timing (PC) with respect to the time the input signals (I) reach the valid state (V) relative to the
PCI_SYNC_IN clock, tSYS, reference (K) going to the high (H) state or setup time. Also, tPCRHFV symbolizes PCI timing (PC)
with respect to the time hard reset (R) went high (H) relative to the frame signal (F) going to the valid (V) state.
2. See the timing measurement conditions in the PCI 2.3 Local Bus Specifications.
3. For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered
through the component pin is less than or equal to the leakage current specification.
4. Input timings are measured at the pin.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
48
Freescale Semiconductor
PCI
Table 46 shows the PCI AC Timing Specifications at 33 MHz.
Table 46. PCI AC Timing Specifications at 33 MHz
Symbol 1
Min
Max
Unit
Notes
Clock to output valid
tPCKHOV
—
11
ns
2
Output hold from Clock
tPCKHOX
2
—
ns
2
Clock to output high impedance
tPCKHOZ
—
14
ns
2, 3
Input setup to Clock
tPCIVKH
3.0
—
ns
2, 4
Input hold from Clock
tPCIXKH
0
—
ns
2, 4
Parameter
Notes:
1. Note that the symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state)
(reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tPCIVKH
symbolizes PCI timing (PC) with respect to the time the input signals (I) reach the valid state (V) relative to the PCI_SYNC_IN
clock, tSYS, reference (K) going to the high (H) state or setup time. Also, tPCRHFV symbolizes PCI timing (PC) with respect to
the time hard reset (R) went high (H) relative to the frame signal (F) going to the valid (V) state.
2. See the timing measurement conditions in the PCI 2.3 Local Bus Specifications.
3. For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered
through the component pin is less than or equal to the leakage current specification.
4. Input timings are measured at the pin.
Figure 30 provides the AC test load for PCI.
Output
Z0 = 50 Ω
RL = 50 Ω
NVDD/2
Figure 30. PCI AC Test Load
Figure 31 shows the PCI input AC timing conditions.
CLK
tPCIVKH
tPCIXKH
Input
Figure 31. PCI Input AC Timing Measurement Conditions
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
49
PCI
Figure 32 shows the PCI output AC timing conditions.
CLK
tPCKHOV
tPCKHOX
Output Delay
tPCKHOZ
High-Impedance
Output
Figure 32. PCI Output AC Timing Measurement Condition
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
50
Freescale Semiconductor
Timers
14 Timers
This section describes the DC and AC electrical specifications for the timers.
14.1
Timers DC Electrical Characteristics
Table 47 provides the DC electrical characteristics for the MPC8313E timers pins, including TIN, TOUT,
TGATE, and RTC_CLK.
Table 47. Timers DC Electrical Characteristics
Characteristic
14.2
Symbol
Condition
Min
Max
Unit
Output high voltage
VOH
IOH = –8.0 mA
2.4
—
V
Output low voltage
VOL
IOL = 8.0 mA
—
0.5
V
Output low voltage
VOL
IOL = 3.2 mA
—
0.4
V
Input high voltage
VIH
—
2.0
NVDD + 0.3
V
Input low voltage
VIL
—
–0.3
0.8
V
Input current
IIN
0 V ≤ VIN ≤ NVDD
—
±5
μA
Timers AC Timing Specifications
Table 48 provides the Timers input and output AC timing specifications.
Table 48. Timers Input AC Timing Specifications 1
Characteristic
Timers inputs—minimum pulse width
Symbol 2
Min
Unit
tTIWID
20
ns
Notes:
1. Input specifications are measured from the 50% level of the signal to the 50% level of the rising edge of SYS_CLK_IN.
Timings are measured at the pin.
2. Timers inputs and outputs are asynchronous to any visible clock. Timers outputs should be synchronized before use by any
external synchronous logic. Timers inputs are required to be valid for at least tTIWID ns to ensure proper operation
Figure 33 provides the AC test load for the Timers.
Output
Z0 = 50 Ω
RL = 50 Ω
NVDD/2
Figure 33. Timers AC Test Load
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
51
GPIO
15 GPIO
This section describes the DC and AC electrical specifications for the GPIO.
15.1
GPIO DC Electrical Characteristics
Table 49 provides the DC electrical characteristics for the GPIO.
Table 49. GPIO DC Electrical Characteristics
Characteristic
15.2
Symbol
Condition
Min
Max
Unit
Output high voltage
VOH
IOH = –8.0 mA
2.4
—
V
Output low voltage
VOL
IOL = 8.0 mA
—
0.5
V
Output low voltage
VOL
IOL = 3.2 mA
—
0.4
V
Input high voltage
VIH
—
2.0
NVDD + 0.3
V
Input low voltage
VIL
—
–0.3
0.8
V
Input current
IIN
0 V ≤ VIN ≤ NVDD
—
±5
μA
GPIO AC Timing Specifications
Table 50 provides the GPIO input and output AC timing specifications.
Table 50. GPIO Input AC Timing Specifications 1
Characteristic
GPIO inputs—minimum pulse width
Symbol 2
Min
Unit
tPIWID
20
ns
Notes:
1. Input specifications are measured from the 50% level of the signal to the 50% level of the rising edge of SYS_CLKIN. Timings
are measured at the pin.
2. GPIO inputs and outputs are asynchronous to any visible clock. GPIO outputs should be synchronized before use by any
external synchronous logic. GPIO inputs are required to be valid for at least tPIWID ns to ensure proper operation.
Figure 34 provides the AC test load for the GPIO.
Output
Z0 = 50 Ω
RL = 50 Ω
NVDD/2
Figure 34. GPIO AC Test Load
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
52
Freescale Semiconductor
IPIC
16 IPIC
This section describes the DC and AC electrical specifications for the external interrupt pins.
16.1
IPIC DC Electrical Characteristics
Table 51 provides the DC electrical characteristics for the external interrupt pins.
Table 51. IPIC DC Electrical Characteristics
Characteristic
16.2
Symbol
Condition
Min
Max
Unit
Input high voltage
VIH
2.0
NVDD + 0.3
V
Input low voltage
VIL
–0.3
0.8
V
Input current
IIN
±5
μA
Output low voltage
VOL
IOL = 8.0 mA
—
0.5
V
Output low voltage
VOL
IOL = 3.2 mA
—
0.4
V
IPIC AC Timing Specifications
Table 52 provides the IPIC input and output AC timing specifications.
Table 52. IPIC Input AC Timing Specifications 1
Characteristic
IPIC inputs—minimum pulse width
Symbol 2
Min
Unit
tPIWID
20
ns
Notes:
1. Input specifications are measured from the 50% level of the signal to the 50% level of the rising edge of SYS_CLK_IN.
Timings are measured at the pin.
2. IPIC inputs and outputs are asynchronous to any visible clock. IPIC outputs should be synchronized before use by any
external synchronous logic. IPIC inputs are required to be valid for at least tPIWID ns to ensure proper operation when working
in edge triggered mode.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
53
SPI
17 SPI
This section describes the DC and AC electrical specifications for the SPI of the MPC8313E
17.1 SPI DC Electrical Characteristics
Table 53 provides the DC electrical characteristics for the MPC8313E SPI.
Table 53. SPI DC Electrical Characteristics
Characteristic
Symbol
Condition
Min
Max
Unit
Output high voltage
VOH
IOH = –6.0 mA
2.4
—
V
Output low voltage
VOL
IOL = 6.0 mA
—
0.5
V
Output low voltage
VOL
IOL = 3.2 mA
—
0.4
V
Input high voltage
VIH
—
2.0
OVDD + 0.3
V
Input low voltage
VIL
—
–0.3
0.8
V
Input current
IIN
0 V ≤ VIN ≤ OVDD
—
±5
μA
17.2 SPI AC Timing Specifications
Table 54 and provide the SPI input and output AC timing specifications.
Table 54. SPI AC Timing Specifications 1
Symbol 2
Min
Max
Unit
SPI outputs—Master mode (internal clock) delay
tNIKHOV
0.5
6
ns
SPI outputs—Slave mode (external clock) delay
tNEKHOV
2
8
ns
SPI inputs—Master mode (internal clock) input setup time
tNIIVKH
6
ns
SPI inputs—Master mode (internal clock) input hold time
tNIIXKH
0
ns
SPI inputs—Slave mode (external clock) input setup time
tNEIVKH
4
ns
SPI inputs—Slave mode (external clock) input hold time
tNEIXKH
2
ns
Characteristic
Notes:
1. Output specifications are measured from the 50% level of the rising edge of SYS_CLK_IN to the 50% level of the signal.
Timings are measured at the pin.
2. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tNIKHOV symbolizes the NMSI
outputs internal timing (NI) for the time tSPI memory clock reference (K) goes from the high state (H) until outputs (O) are
valid (V).
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
54
Freescale Semiconductor
SPI
Figure 35 provides the AC test load for the SPI.
Z0 = 50 Ω
Output
RL = 50 Ω
OVDD/2
Figure 35. SPI AC Test Load
Figure 36 through Figure 37 represent the AC timing from Table 54. Note that although the specifications
generally reference the rising edge of the clock, these AC timing diagrams also apply when the falling edge
is the active edge.
Figure 36 shows the SPI timing in Slave mode (external clock).
SPICLK (input)
Input Signals:
SPIMOSI
(See Note)
tNEIVKH
tNEIXKH
tNEKHOV
Output Signals:
SPIMISO
(See Note)
Note: The clock edge is selectable on SPI.
Figure 36. SPI AC Timing in Slave Mode (External Clock) Diagram
Figure 37 shows the SPI timing in Master mode (internal clock).
SPICLK (output)
Input Signals:
SPIMISO
(See Note)
tNIIVKH
Output Signals:
SPIMOSI
(See Note)
tNIIXKH
tNIKHOV
Note: The clock edge is selectable on SPI.
Figure 37. SPI AC Timing in Master Mode (Internal Clock) Diagram
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
55
Package and Pin Listings
18 Package and Pin Listings
This section details package parameters, pin assignments, and dimensions. The MPC8313E is available in
a thermally enhanced plastic ball grid array (TEPBGAII), see Section 18.1, “Package Parameters for the
MPC8313E TEPBGAII,” and Section 18.2, “Mechanical Dimensions of the MPC8313E TEPBGAII,” for
information on the TEPBGAII.
18.1
Package Parameters for the MPC8313E TEPBGAII
The package parameters are as provided in the following list. The package type is 27 mm × 27 mm, 516
TEPBGAII.
Package outline
27 mm × 27 mm
Interconnects
516
Pitch
1.00 mm
Module height (typical)
2.25 mm
Solder Balls
95.5 Sn/0.5 Cu/4Ag (VR package)
Ball diameter (typical)
0.6 mm
18.2
Mechanical Dimensions of the MPC8313E TEPBGAII
Figure 38 shows the mechanical dimensions and bottom surface nomenclature of the 516-TEPBGAII
package.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
56
Freescale Semiconductor
Package and Pin Listings
Figure 38. Mechanical Dimension and Bottom Surface Nomenclature of the MPC8313E TEPBGAII
1.
2.
3.
4.
5.
All dimensions are in millimeters.
Dimensions and tolerances per ASME Y14.5M-1994.
Maximum solder ball diameter measured parallel to datum A.
Datum A, the seating plane, is determined by the spherical crowns of the solder balls.
Package code 5368 is to account for PGE and the built–in heat spreader.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
57
Package and Pin Listings
18.3
Pinout Listings
Table 55 provides the pin-out listing for the MPC8313E, TEPBGAII package.
Table 55. MPC8313E TEPBGAII Pinout Listing
Signal
Package Pin Number
Pin Type
Power
Supply
Notes
DDR Memory Controller Interface
MEMC_MDQ[0]
A8
IO
GVDD
MEMC_MDQ[1]
A9
IO
GVDD
MEMC_MDQ[2]
C10
IO
GVDD
MEMC_MDQ[3]
C9
IO
GVDD
MEMC_MDQ[4]
E9
IO
GVDD
MEMC_MDQ[5]
E11
IO
GVDD
MEMC_MDQ[6]
E10
IO
GVDD
MEMC_MDQ[7]
C8
IO
GVDD
MEMC_MDQ[8]
E8
IO
GVDD
MEMC_MDQ[9]
A6
IO
GVDD
MEMC_MDQ[10]
B6
IO
GVDD
MEMC_MDQ[11]
C6
IO
GVDD
MEMC_MDQ[12]
C7
IO
GVDD
MEMC_MDQ[13]
D7
IO
GVDD
MEMC_MDQ[14]
D6
IO
GVDD
MEMC_MDQ[15]
A5
IO
GVDD
MEMC_MDQ[16]
A19
IO
GVDD
MEMC_MDQ[17]
D18
IO
GVDD
MEMC_MDQ[18]
A17
IO
GVDD
MEMC_MDQ[19]
E17
IO
GVDD
MEMC_MDQ[20]
E16
IO
GVDD
MEMC_MDQ[21]
C18
IO
GVDD
MEMC_MDQ[22]
D19
IO
GVDD
MEMC_MDQ[23]
C19
IO
GVDD
MEMC_MDQ[24]
E19
IO
GVDD
MEMC_MDQ[25]
A22
IO
GVDD
MEMC_MDQ[26]
C21
IO
GVDD
MEMC_MDQ[27]
C20
IO
GVDD
MEMC_MDQ[28]
A21
IO
GVDD
MEMC_MDQ[29]
A20
IO
GVDD
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
58
Freescale Semiconductor
Package and Pin Listings
Table 55. MPC8313E TEPBGAII Pinout Listing (continued)
Package Pin Number
Pin Type
Power
Supply
MEMC_MDQ[30]
C22
IO
GVDD
MEMC_MDQ[31]
B22
IO
GVDD
MEMC_MDM0
B7
O
GVDD
MEMC_MDM1
E6
O
GVDD
MEMC_MDM2
E18
O
GVDD
MEMC_MDM3
E20
O
GVDD
MEMC_MDQS[0]
A7
IO
GVDD
MEMC_MDQS[1]
E7
IO
GVDD
MEMC_MDQS[2]
B19
IO
GVDD
MEMC_MDQS[3]
A23
IO
GVDD
MEMC_MBA[0]
D15
O
GVDD
MEMC_MBA[1]
A18
O
GVDD
MEMC_MBA[2]
A15
O
GVDD
MEMC_MA0
E12
O
GVDD
MEMC_MA1
D11
O
GVDD
MEMC_MA2
B11
O
GVDD
MEMC_MA3
A11
O
GVDD
MEMC_MA4
A12
O
GVDD
MEMC_MA5
E13
O
GVDD
MEMC_MA6
C12
O
GVDD
MEMC_MA7
E14
O
GVDD
MEMC_MA8
B15
O
GVDD
MEMC_MA9
C17
O
GVDD
MEMC_MA10
C13
O
GVDD
MEMC_MA11
A16
O
GVDD
MEMC_MA12
C15
O
GVDD
MEMC_MA13
C16
O
GVDD
MEMC_MA14
E15
O
GVDD
MEMC_MWE
B18
O
GVDD
MEMC_MRAS
C11
O
GVDD
MEMC_MCAS
B10
O
GVDD
MEMC_MCS[0]
D10
O
GVDD
MEMC_MCS[1]
A10
O
GVDD
MEMC_MCKE
B14
O
GVDD
Signal
Notes
3
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
59
Package and Pin Listings
Table 55. MPC8313E TEPBGAII Pinout Listing (continued)
Package Pin Number
Pin Type
Power
Supply
MEMC_MCK
A13
O
GVDD
MEMC_MCK
A14
O
GVDD
MEMC_MODT[0]
B23
O
GVDD
MEMC_MODT[1]
C23
O
GVDD
Signal
Notes
Local Bus Controller Interface
LAD0
K25
IO
LVDD
LAD1
K24
IO
LVDD
LAD2
K23
IO
LVDD
LAD3
K22
IO
LVDD
LAD4
J25
IO
LVDD
LAD5
J24
IO
LVDD
LAD6
J23
IO
LVDD
LAD7
J22
IO
LVDD
LAD8
H24
IO
LVDD
LAD9
F26
IO
LVDD
LAD10
G24
IO
LVDD
LAD11
F25
IO
LVDD
LAD12
E25
IO
LVDD
LAD13
F24
IO
LVDD
LAD14
G22
IO
LVDD
LAD15
F23
IO
LVDD
LA16
AC25
O
LVDD
LA17
AC26
O
LVDD
LA18
AB22
O
LVDD
LA19
AB23
O
LVDD
LA20
AB24
O
LVDD
LA21
AB25
O
LVDD
LA22
AB26
O
LVDD
LA23
E22
O
LVDD
LA24
E23
O
LVDD
LA25
D22
O
LVDD
LCS[0]
D23
O
LVDD
LCS[1]
J26
O
LVDD
LCS[2]
F22
O
LVDD
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
60
Freescale Semiconductor
Package and Pin Listings
Table 55. MPC8313E TEPBGAII Pinout Listing (continued)
Package Pin Number
Pin Type
Power
Supply
LCS[3]
D26
O
LVDD
LWE[0]
E24
O
LVDD
LWE[1]
H26
O
LVDD
LBCTL
L22
O
LVDD
LALE/M1LALE/M2LALE
E26
O
LVDD
LGPL0
AA23
O
LVDD
LGPL1
AA24
O
LVDD
LGPL2
AA25
O
LVDD
LGPL3
AA26
O
LVDD
LGPL4
Y22
IO
LVDD
LGPL5
E21
O
LVDD
LCLK0
H22
O
LVDD
LCLK1
G26
O
LVDD
LA0/GPIO[0]
AC24
IO
LVDD
LA1/GPIO[1]
Y24
IO
LVDD
LA2/GPIO[2]
Y26
IO
LVDD
LA3/GPIO[3]
W22
IO
LVDD
LA4/GPIO[4]
W24
IO
LVDD
LA5/GPIO[5]
W26
IO
LVDD
LA6/GPIO[6]
V22
IO
LVDD
LA7/GPIO[7]
V23
IO
LVDD
LA8/GPIO[13]
V24
IO
LVDD
LA9/GPIO[14]
V25
IO
LVDD
LA10
V26
O
LVDD
LA11
U22
O
LVDD
LA12
AD24
O
LVDD
LA13
L25
O
LVDD
LA14
L24
O
LVDD
LA15
K26
O
LVDD
UART_SOUT1/MSRCID0
N2
O
NVDD
UART_SIN1/MSRCID1
M5
IO
NVDD
UART_CTS[1]/GPIO[8]/MSRCID2
M1
IO
NVDD
UART_RTS[1]/GPIO[9]/MSRCID3
K1
IO
NVDD
Signal
Notes
DUART
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
61
Package and Pin Listings
Table 55. MPC8313E TEPBGAII Pinout Listing (continued)
Package Pin Number
Pin Type
Power
Supply
UART_SOUT2/MSRCID4
M3
O
NVDD
UART_SIN2/MDVAL
L1
IO
NVDD
UART_CTS[2]
L5
IO
NVDD
UART_RTS[2]
L3
IO
NVDD
IIC1_SDA/CKSTOP_OUT
J4
IO
NVDD
2
IIC1_SCL/CKSTOP_IN
J2
IO
NVDD
2
IIC2_SDA/PMC_PWR_OK/GPIO[10]
J3
IO
NVDD
2
IIC2_SCL/GPIO[11]
H5
IO
NVDD
2
MCP_OUT
G5
O
NVDD
2
IRQ[0]/MCP_IN
K5
I
NVDD
IRQ[1]
K4
I
NVDD
IRQ[2]
K2
I
NVDD
IRQ[3] /CKSTOP_OUT
K3
IO
NVDD
IRQ[4]/ CKSTOP_IN/GPIO[12]
J1
IO
NVDD
CFG_CLKIN_DIV
D5
I
NVDD
EXT_PWR_CTRL
J5
O
NVDD
R24
I
NVDD
TCK
E1
I
NVDD
TDI
E2
I
NVDD
4
TDO
E3
O
NVDD
3
TMS
E4
I
NVDD
4
TRST
E5
I
NVDD
4
F4
I
NVDD
6
F5
O
NVDD
F2
IO
NVDD
Signal
Notes
I2C interface
Interrupts
Configuration
CFG_LBIU_MUX_EN
JTAG
TEST
TEST_MODE
DEBUG
QUIESCE
System Control
HRESET
1
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
62
Freescale Semiconductor
Package and Pin Listings
Table 55. MPC8313E TEPBGAII Pinout Listing (continued)
Package Pin Number
Pin Type
Power
Supply
PORESET
F3
I
NVDD
SRESET
F1
I
NVDD
SYS_CR_CLK_IN
U26
I
NVDD
SYS_CR_CLK_OUT
U25
O
NVDD
SYS_CLK_IN
U23
I
NVDD
USB_CR_CLK_IN
T26
I
NVDD
USB_CR_CLK_OUT
R26
O
NVDD
USB_CLK_IN
T22
I
NVDD
PCI_SYNC_OUT
U24
O
NVDD
RTC_PIT_CLOCK
R22
I
NVDD
PCI_SYNC_IN
T24
I
NVDD
AVDD1
F14
I
Double
with Pad
AVDD2
P21
I
Double
with Pad
PCI_INTA
AF7
O
NVDD
PCI_RESET_OUT
AB11
O
NVDD
PCI_AD[0]
AB20
IO
NVDD
PCI_AD[1]
AF23
IO
NVDD
PCI_AD[2]
AF22
IO
NVDD
PCI_AD[3]
AB19
IO
NVDD
PCI_AD[4]
AE22
IO
NVDD
PCI_AD[5]
AF21
IO
NVDD
PCI_AD[6]
AD19
IO
NVDD
PCI_AD[7]
AD20
IO
NVDD
PCI_AD[8]
AC18
IO
NVDD
PCI_AD[9]
AD18
IO
NVDD
PCI_AD[10]
AB18
IO
NVDD
PCI_AD[11]
AE19
IO
NVDD
PCI_AD[12]
AB17
IO
NVDD
PCI_AD[13]
AE18
IO
NVDD
Signal
Notes
Clocks
3
MISC
PCI
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
63
Package and Pin Listings
Table 55. MPC8313E TEPBGAII Pinout Listing (continued)
Package Pin Number
Pin Type
Power
Supply
PCI_AD[14]
AD17
IO
NVDD
PCI_AD[15]
AF19
IO
NVDD
PCI_AD[16]
AB14
IO
NVDD
PCI_AD[17]
AF15
IO
NVDD
PCI_AD[18]
AD14
IO
NVDD
PCI_AD[19]
AE14
IO
NVDD
PCI_AD[20]
AF12
IO
NVDD
PCI_AD[21]
AE11
IO
NVDD
PCI_AD[22]
AD12
IO
NVDD
PCI_AD[23]
AB13
IO
NVDD
PCI_AD[24]
AF9
IO
NVDD
PCI_AD[25]
AD11
IO
NVDD
PCI_AD[26]
AE10
IO
NVDD
PCI_AD[27]
AB12
IO
NVDD
PCI_AD[28]
AD10
IO
NVDD
PCI_AD[29]
AC10
IO
NVDD
PCI_AD[30]
AF10
IO
NVDD
PCI_AD[31]
AF8
IO
NVDD
PCI_C/BE[0]
AC19
IO
NVDD
PCI_C/BE[1]
AB15
IO
NVDD
PCI_C/BE[2]
AF14
IO
NVDD
PCI_C/BE[3]
AF11
IO
NVDD
PCI_PAR
AD16
IO
NVDD
PCI_FRAME
AF16
IO
NVDD
5
PCI_TRDY
AD13
IO
NVDD
5
PCI_IRDY
AC15
IO
NVDD
5
PCI_STOP
AF13
IO
NVDD
5
PCI_DEVSEL
AC14
IO
NVDD
5
PCI_IDSEL
AF20
I
NVDD
PCI_SERR
AE15
IO
NVDD
5
PCI_PERR
AD15
IO
NVDD
5
PCI_REQ0
AB10
IO
NVDD
PCI_REQ1/CPCI_HS_ES
AD9
I
NVDD
PCI_REQ2
AD8
I
NVDD
Signal
Notes
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
64
Freescale Semiconductor
Package and Pin Listings
Table 55. MPC8313E TEPBGAII Pinout Listing (continued)
Package Pin Number
Pin Type
Power
Supply
PCI_GNT0
AC11
IO
NVDD
PCI_GNT1/CPCI_HS_LED
AE7
O
NVDD
PCI_GNT2/CPCI_HS_ENUM
AD7
O
NVDD
M66EN
AD21
I
NVDD
PCI_CLK0
AF17
O
NVDD
PCI_CLK1
AB16
O
NVDD
PCI_CLK2
AF18
O
NVDD
PCI_PME
AD22
IO
NVDD
Signal
Notes
ETSEC1/_USBULPI
TSEC1_COL/USBDR_TXDRXD0
AD2
IO
LVDDB
TSEC1_CRS/USBDR_TXDRXD1
AC3
IO
LVDDB
TSEC1_GTX_CLK/USBDR_TXDRXD2
AF3
IO
LVDDB
TSEC1_RX_CLK/USBDR_TXDRXD3
AE3
IO
LVDDB
TSCE1_RX_DV/USBDR_TXDRXD4
AD3
IO
LVDDB
TSEC1_RXD[3]/USBDR_TXDRXD5
AC6
IO
LVDDB
TSEC1_RXD[2]/USBDR_TXDRXD6
AF4
IO
LVDDB
TSEC1_RXD[1]/USBDR_TXDRXD7
AB6
IO
LVDDB
TSEC1_RXD[0]/USBDR_NXT/TSEC_1588_TRIG1
AB5
I
LVDDB
TSEC1_RX_ER/USBDR_DIR/TESC_1588_TRIG2
AD4
I
LVDDB
TSEC1_TX_CLK/USBDR_CLK/TSEC_1588_CLK
AF5
I
LVDDB
TSEC1_TXD[3]/TSEC_1588_GCLK
AE6
O
LVDDB
TSEC1_TXD[2]/TSEC_1588_PP1
AC7
O
LVDDB
TSEC1_TXD[1]/TSEC_1588_PP2
AD6
O
LVDDB
TSEC1_TXD[0]/USBDR_STP/TSEC_1588_PP3
AD5
O
LVDDB
TSEC1_TX_EN/TSEC_1588_ALARM1
AB7
O
LVDDB
TSEC1_TX_ER/TSEC_1588_ALARM2
AB8
O
LVDDB
TSEC1_GTX_CLK125
AE1
I
LVDDB
TSEC1_MDC
AF6
O
NVDD
TSEC1_MDIO
AB9
IO
NVDD
TSEC2_COL/GTM1_TIN4/GTM2_TIN3/GPIO[15]
AB4
IO
LVDDA
TSEC2_CRS/GTM1_TGATE4/GTM2_TGATE3/GPIO[16]
AB3
IO
LVDDA
TSEC2_GTX_CLK/GTM1_TOUT4/GTM2_TOUT3/GPIO[17]
AC1
IO
LVDDA
TSEC2_RX_CLK/GTM1_TIN2/GTM2_TIN1/GPIO[18]
AC2
IO
LVDDA
3
2
ETSEC2
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
65
Package and Pin Listings
Table 55. MPC8313E TEPBGAII Pinout Listing (continued)
Package Pin Number
Pin Type
Power
Supply
AA3
IO
LVDDA
TSEC2_RXD[3]/GPIO[20]
Y5
IO
LVDDA
TSEC2_RXD[2]/GPIO[21]
AA4
IO
LVDDA
TSEC2_RXD[1]/GPIO[22]
AB2
IO
LVDDA
TSEC2_RXD[0]/GPIO[23]
AA5
IO
LVDDA
TSEC2_RX_ER/GTM1_TOUT2/GTM2_TOUT1/GPIO[24]
AA2
IO
LVDDA
TSEC2_TX_CLK/GPIO[25]
AB1
IO
LVDDA
TSEC2_TXD[3]/CFG_RESET_SOURCE[0]
W3
IO
LVDDA
TSEC2_TXD[2]/CFG_RESET_SOURCE[1]
Y1
IO
LVDDA
TSEC2_TXD[1]/CFG_RESET_SOURCE[2]
W5
IO
LVDDA
TSEC2_TXD[0]/CFG_RESET_SOURCE[3]
Y3
IO
LVDDA
TSEC2_TX_EN/GPIO[26]
AA1
IO
LVDDA
TSEC2_TX_ER/GPIO[27]
W1
IO
LVDDA
TXA
U3
O
TXA
V3
O
RXA
U1
I
RXA
V1
I
TXB
P4
O
TXB
N4
O
RXB
R1
I
RXB
P1
I
SD_IMP_CAL_RX
V5
I
SD_REF_CLK
T5
I
SD_REF_CLK
T4
I
SD_PLL_TPD
T2
O
SD_IMP_CAL_TX
N5
I
SDAVDD
R5
IO
SD_PLL_TPA_ANA
R4
O
SDAVSS
R3
IO
USB_DP
P26
IO
USB_DM
N26
IO
USB_VBUS
P24
IO
Signal
TSCE2_RX_DV/GTM1_TGATE2/GTM2_TGATE1/GPIO[19]
Notes
SGMII PHY
USB PHY
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
66
Freescale Semiconductor
Package and Pin Listings
Table 55. MPC8313E TEPBGAII Pinout Listing (continued)
Signal
Power
Supply
Package Pin Number
Pin Type
USB_TPA
L26
IO
USB_RBIAS
M24
IO
USB_PLL_PWR3
M26
IO
USB_PLL_GND
N24
IO
USB_PLL_PWR1
N25
IO
USB_VSSA_BIAS
M25
IO
USB_VDDA_BIAS
M22
IO
USB_VSSA
N22
IO
USB_VDDA
P22
IO
USBDR_DRIVE_VBUS/GTM1_TIN1/GTM2_TIN2
AD23
IO
NVDD
USBDR_PWRFAULT/GTM1_TGATE1/GTM2_TGATE2
AE23
IO
NVDD
USBDR_PCTL0/GTM1_TOUT1
AC22
O
NVDD
USBDR_PCTL1
AB21
O
NVDD
SPIMOSI/GTM1_TIN3/GTM2_TIN4/GPIO[28]
H1
IO
NVDD
SPIMISO/GTM1_TGATE3/GTM2_TGATE4/GPIO[29]/LDVAL
H3
IO
NVDD
SPICLK/GTM1_TOUT3/GPIO[30]
G1
IO
NVDD
SPISEL/GPIO[31]
G3
IO
NVDD
Notes
GTM/USB
SPI
Power and Ground Supplies
GV DD
A2,A3,A4,A24,A25,B3,
B4,B5,B12,B13,B20,
B21,B24,B25,B26,D1,
D2,D8,D9,D16,D17
LVDD
D24,D25,G23,H23,R23,
T23,W25,Y25,
AA22,AC23
LVDDA
W2,Y2
LVDDB
AC8,AC9,AE4,AE5
MV REF
C14,D14
NVDD
G4,H4,L2,M2,AC16,
AC17,AD25,AD26,AE12,
AE13,AE20,AE21,AE24,
AE25,AE26,AF24,
AF25
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
67
Package and Pin Listings
Table 55. MPC8313E TEPBGAII Pinout Listing (continued)
Signal
Package Pin Number
VDD
K11,K12,K13,K14,K15,K
16,L10,L17,M10,M17,
N10,N17,U12,U13,
T1,U2,V2,P5,U4
VDDC
F6,F10,F19,K6,K10,K17,
K21,P6,P10,P17,R10,
R17,T10,T17,U10,U11,
U14,U15,U16,U17,W6,
W21,AA6,AA10,AA14,
AA19
VSS
B1,B2,B8,B9,B16,B17,
C1,C2,C3,C4,C5,C24,
C25,C26,D3,D4,D12,
D13,D20,D21,F8,F11,
F13,F16,F17,F21,G2,
G25,H2,H6,H21,H25,
L4,L6,L11,L12,L13,L14,
L15,L16,L21,L23,M4,
M11,M12,M13,M14,
M15,M16,M23,N1,
N3,N6,N11,N12,N13,
N14,N15,N16,N21,N23,
P11,P12,P13,P14,P15,
P16,P23,P25,R11,R12,
R13,R14,R15,R16,R25,
T6,T11,T12,T13,T14,
T15,T16,T21,T25,U5,
U6,U21,W4,W23,Y4,
Y23,AA8,AA11,AA13,
AA16,AA17,AA21,AC4,
AC5,AC12,AC13,AC20,
AC21,AD1,AE2,AE8,
AE9,AE16,AE17,AF2,
P2, R2,T3,P3,V4
Power
Supply
Pin Type
Notes
Notes:
1. This pin is an open drain signal. A weak pull-up resistor (1 kΩ) should be placed on this pin to NVDD
2. This pin is an open drain signal. A weak pull-up resistor (2–10 kΩ) should be placed on this pin to NVDD.
3. This output is actively driven during reset rather than being three-stated during reset.
4. These JTAG pins have weak internal pull-up P-FETs that are always enabled.
5. This pin should have a weak pull up if the chip is in PCI host mode. Follow PCI specifications recommendation.
6. This pin must always be tied to VSS.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
68
Freescale Semiconductor
Clocking
19 Clocking
Figure 39 shows the internal distribution of clocks within the MPC8313E.
MPC8313E
e300c3 core
core_clk
Core PLL
USB Mac
xM
1
USB PHY
PLL
mux
csb_clk
to DDR
memory
controller
DDR
Clock
Divider
/2
USB_CLK_IN
USB_CR_CLK_IN
DDR
Memory
Device
MEMC_MCK
MEMC_MCK
ddr_clk
x
Crystal
/1,/2
USB_CR_CLK_OUT
L2
System
PLL
Clock
Unit
lbc_clk
/n
To local bus
LCLK[0:1]
LBC
Clock
Divider
csb_clk to rest
of the device
CFG_CLKIN
_DIV
Local Bus
Memory
Device
PCI_CLK/
PCI_SYNC_IN
SYS_CLK_IN
SYS_CR_CLK_IN
1
0
Crystal
PCI_SYNC_OUT
PCI Clock
Divider (÷2)
SYS_CR_CLK_OUT
GTX_CLK125
125-MHz source
3
eTSEC
Protocol
Converter
RTC
Sys Ref
1
2
PCI_CLK_OUT[0:2]
RTC_CLK (32 KHz)
Multiplication factor M = 1, 1.5, 2, 2.5, and 3.
Multiplication factor L = 2, 3, 4, 5 and 6. Value is decided by RCWLR[SPMF].
Figure 39. MPC8313E Clock Subsystem
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
69
Clocking
The primary clock source for the MPC8313E can be one of two inputs, SYS_CLK_IN or PCI_CLK,
depending on whether the device is configured in PCI host or PCI agent mode. When the device is
configured as a PCI host device, SYS_CLK_IN is its primary input clock. SYS_CLK_IN feeds the PCI
clock divider (÷2) and the multiplexors for PCI_SYNC_OUT and PCI_CLK_OUT. The
CFG_CLKIN_DIV configuration input selects whether SYS_CLK_IN or SYS_CLK_IN/2 is driven out
on the PCI_SYNC_OUT signal. The OCCR[PCICOEn] parameters select whether the PCI_SYNC_OUT
is driven out on the PCI_CLK_OUTn signals.
PCI_SYNC_OUT is connected externally to PCI_SYNC_IN to allow the internal clock subsystem to
synchronize to the system PCI clocks. PCI_SYNC_OUT must be connected properly to PCI_SYNC_IN,
with equal delay to all PCI agent devices in the system, to allow the device to function. When the device
is configured as a PCI agent device, PCI_SYNC_IN is the primary input clock. When the device is
configured as a PCI agent device the SYS_CLK_IN signal should be tied to VSS.
As shown in Figure 39, the primary clock input (frequency) is multiplied up by the system phase-locked
loop (PLL) and the clock unit to create the coherent system bus clock (csb_clk), the internal clock for the
DDR controller (ddr_clk), and the internal clock for the local bus interface unit (lbc_clk).
The csb_clk frequency is derived from a complex set of factors that can be simplified into the following
equation:
csb_clk = {PCI_SYNC_IN × (1 + ~CFG_CLKIN_DIV)} × SPMF
In PCI host mode, PCI_SYNC_IN × (1 + ~CFG_CLKIN_DIV) is the SYS_CLK_IN frequency.
The csb_clk serves as the clock input to the e300 core. A second PLL inside the e300 core multiplies up
the csb_clk frequency to create the internal clock for the e300 core (core_clk). The system and core PLL
multipliers are selected by the SPMF and COREPLL fields in the reset configuration word low (RCWL)
which is loaded at power-on reset or by one of the hard-coded reset options. See Chapter 4, “Reset,
Clocking, and Initialization,” in the MPC8313E PowerQUICC II Pro Integrated Host Processor Reference
Manual for more information on the clock subsystem.
The internal ddr_clk frequency is determined by the following equation:
ddr_clk = csb_clk × (1 + RCWL[DDRCM])
Note that ddr_clk is not the external memory bus frequency; ddr_clk passes through the DDR clock divider
(÷2) to create the differential DDR memory bus clock outputs (MCK and MCK). However, the data rate
is the same frequency as ddr_clk.
The internal lbc_clk frequency is determined by the following equation:
lbc_clk = csb_clk × (1 + RCWL[LBCM])
Note that lbc_clk is not the external local bus frequency; lbc_clk passes through the a LBC clock divider
to create the external local bus clock outputs (LCLK[0:1]). The LBC clock divider ratio is controlled by
LCCR[CLKDIV].
In addition, some of the internal units may be required to be shut off or operate at lower frequency than
the csb_clk frequency. Those units have a default clock ratio that can be configured by a memory mapped
register after the device comes out of reset. Table 56 specifies which units have a configurable clock
frequency.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
70
Freescale Semiconductor
Clocking
Table 56. Configurable Clock Units
Default
Frequency
Options
TSEC1
csb_clk
Off, csb_clk, csb_clk/2, csb_clk/3
TSEC2
csb_clk
Off, csb_clk, csb_clk/2, csb_clk/3
Security Core, I2C, SAP, TPR
csb_clk
Off, csb_clk, csb_clk/2, csb_clk/3
USB DR
csb_clk
Off, csb_clk, csb_clk/2, csb_clk/3
PCI and DMA complex
csb_clk
Off, csb_clk
Unit
Table 57 provides the operating frequencies for the MPC8313E TEPBGA II under recommended
operating conditions (see Table 2).
Table 57. Operating Frequencies for TEPBGA I I
Characteristic1
Max Operating Frequency
Unit
e300 core frequency (core_clk)
333
MHz
Coherent system bus frequency
(csb_clk)
167
MHz
DDR1/2 memory bus frequency
(MCK)2
167
MHz
Local bus frequency
(LCLKn)3
33–66
MHz
PCI input frequency (SYS_CLK_IN or PCI_CLK)
24–66
MHz
Notes:
1. The SYS_CLK_IN frequency, RCWL[SPMF], and RCWL[COREPLL] settings must be chosen such that the resulting
csb_clk, MCK, LCLK[0:1], and core_clk frequencies do not exceed their respective maximum or minimum operating
frequencies. The value of SCCR[ENCCM] and SCCR[USBDRCM] must be programmed such that the maximum internal
operating frequency of the Security core and USB modules will not exceed their respective value listed in this table.
2. The DDR data rate is 2x the DDR memory bus frequency.
3. The local bus frequency is 1/2, 1/4, or 1/8 of the lbc_clk frequency (depending on LCCR[CLKDIV]) which is in turn 1x or 2x
the csb_clk frequency (depending on RCWL[LBCM]).
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
71
Clocking
19.1
System PLL Configuration
The system PLL is controlled by the RCWL[SPMF] parameter. Table 58 shows the multiplication factor
encodings for the system PLL.
Table 58. System PLL Multiplication Factors
RCWL[SPMF]
System PLL Multiplication
Factor
0000
Reserved
0001
Reserved
0010
×2
0011
×3
0100
×4
0101
×5
0110
×6
0111–1111
Reserved
As described in Section 19, “Clocking,” The LBCM, DDRCM, and SPMF parameters in the reset
configuration word low and the CFG_CLKIN_DIV configuration input signal select the ratio between the
primary clock input (SYS_CLK_IN or PCI_SYNC_IN) and the internal coherent system bus clock
(csb_clk). Table 59 shows the expected frequency values for the CSB frequency for select csb_clk to
SYS_CLK_IN/PCI_SYNC_IN ratios.
Table 59. CSB Frequency Options
CFG_CLKIN_DIV
at reset 1
SPMF
csb_clk :
Input Clock
Ratio 2
High
0010
2:1
High
0011
3:1
High
0100
4:1
High
0101
5:1
High
0110
6:1
Low
0010
2:1
Low
0011
3:1
Low
0100
4:1
Input
Clock
Frequency(MHz)2
24
25
33.33
csb_clk
Frequency(MHz)
66.67
133
100
100
133
120
125
167
144
150
133
100
100
133
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
72
Freescale Semiconductor
Clocking
Table 59. CSB Frequency Options (continued)
CFG_CLKIN_DIV
at reset 1
1
SPMF
Input
Clock
Frequency(MHz)2
csb_clk :
Input Clock
Ratio 2
24
25
33.33
csb_clk
Frequency(MHz)
167
Low
0101
5:1
120
125
Low
0110
6:1
144
150
66.67
CFG_CLKIN_DIV select the ratio between SYS_CLK_IN and PCI_SYNC_OUT.
SYS_CLK_IN is the input clock in host mode; PCI_CLK is the input clock in agent mode.
2
19.2
Core PLL Configuration
RCWL[COREPLL] selects the ratio between the internal coherent system bus clock (csb_clk) and the e300
core clock (core_clk). Table 60 shows the encodings for RCWL[COREPLL]. COREPLL values that are
not listed in Table 60 should be considered as reserved.
NOTE
Core VCO frequency = Core frequency × VCO divider
VCO divider has to be set properly so that the core VCO frequency is in the
range of 400–800 MHz.
Table 60. e300 Core PLL Configuration
RCWL[COREPLL]
core_clk : csb_clk Ratio
VCO divider 1
0
PLL bypassed
(PLL off, csb_clk clocks core directly)
PLL bypassed
(PLL off, csb_clk clocks core directly)
nnnn
n
n/a
n/a
00
0001
0
1:1
2
01
0001
0
1:1
4
10
0001
0
1:1
8
00
0001
1
1.5:1
2
01
0001
1
1.5:1
4
10
0001
1
1.5:1
8
00
0010
0
2:1
2
01
0010
0
2:1
4
10
0010
0
2:1
8
00
0010
1
2.5:1
2
01
0010
1
2.5:1
4
0–1
2–5
6
nn
0000
11
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
73
Clocking
Table 60. e300 Core PLL Configuration (continued)
RCWL[COREPLL]
1
core_clk : csb_clk Ratio
VCO divider 1
0–1
2–5
6
10
0010
1
2.5:1
8
00
0011
0
3:1
2
01
0011
0
3:1
4
10
0011
0
3:1
8
Core VCO frequency = Core frequency × VCO divider. Note that VCO divider has to be set properly so that the core VCO
frequency is in the range of 400-800MHz.
19.3
Example Clock Frequency Combinations
Table 61 shows several possible frequency combinations that can be selected based on the indicated input
reference frequencies, with RCWLR[LBCM] = 0 and RCWLR[DDRCM] =1, such that the LBC operates
with a frequency equal to the frequency of csb_clk and the DDR controller operates at twice the frequency
of csb_clk.
Table 61. System Clock Frequencies
LBC(lbc_clk)
SYS_CLK_
SPMF vcod
IN/
1
2
PCI_CLK
vco
CSB(csb_
clk)
DDR
(ddr_clk)
/2
e300 Core(core_clk)
/4
/8
USB
ref 3
×1
× 1.5
×2
× 2.5
36
18.0
12.0
144.0
216
288
360
30
15.0
12.0
120.0
180
240
300
×3
24.0
6
2
576.0
144.0
288.0
24.0
5
2
480.0
120.0
240.0
25.0
6
2
600.0
150.0
300.0
37.5
18.8
Note 1
150.0
225
300
375
25.0
5
2
500.0
125.0
250.0
62.5 31.25 15.6
Note1
125.0
188
250
313
375
32.0
5
2
640.0
160.0
320.0
40
20.0
16.0
160.0
240
320
32.0
4
2
512.0
128.0
256.0
32
16.0
16.0
128.0
192
256
320
384
33.3
5
2
666.0
166.5
333.0
41.63 20.8
Note 1
166.5
250
333
33.3
4
2
532.8
133.2
266.4
33.3
16.7
Note 1
133.2
200
266
333
400
48.0
3
2
576.0
144.0
288.0
36
18.0
48.0
144.0
216
288
360
60
64
66.6
360
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
74
Freescale Semiconductor
Clocking
Table 61. System Clock Frequencies (continued)
66.7
2
2
533.4
133.3
266.7
66.7 33.34 16.7
Note 1
133.3
200
267
333
400
Note:
Note 1: USB reference clock must be supplied from a separate source as it must be 12, 16 or 48 MHz, the USB reference must
be supplied from a separate external source using USB_CLK_IN. Note 2: When considering operating frequencies, the valid
system APLL VCO operating range of 400-800 MHz must not be violated.
Note 3: csb_clk frequencies of less than 133MHz will not support Gigabit Ethernet data rates.
1
System PLL Multiplication Factor
System PLL VCO Divider
3
Frequency of USB PLL Input reference
2
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
75
Thermal
20 Thermal
This section describes the thermal specifications of the MPC8313E.
20.1
Thermal Characteristics
Table 62 provides the package thermal characteristics for the 516 27 × 27 mm TEPBGAII.
Table 62. Package Thermal Characteristics for TEPBGAII
Characteristic
Board type
Symbol
TEPBGAII
Unit
Notes
Junction to Ambient Natural
Convection
Single layer board (1s)
RθJA
25
°C/W
1,2
Junction to Ambient Natural
Convection
Four layer board (2s2p)
RθJA
18
°C/W
1,2,3
Junction to Ambient (@200 ft/min)
Single layer board (1s)
RθJMA
20
°C/W
1,3
Junction to Ambient (@200 ft/min)
Four layer board (2s2p)
RθJMA
15
°C/W
1,3
Junction to Board
RθJB
10
°C/W
4
Junction to Case
RθJC
8
°C/W
5
ΨJT
7
°C/W
6
Junction to Package Top
Natural Convection
Notes:
1. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance,
mounting site (board) temperature, ambient temperature, air flow, power dissipation of other components on
the board, and board thermal resistance.
2. Per JEDEC JESD51-2 with the single layer board horizontal. Board meets JESD51-9 specification.
3. Per JEDEC JESD51-6 with the board horizontal.
4. Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature
is measured on the top surface of the board near the package.
5. Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL
SPEC-883 Method 1012.1).
6. Thermal characterization parameter indicating the temperature difference between package top and the
junction temperature per JEDEC JESD51-2. When Greek letters are not available, the thermal
characterization parameter is written as Psi-JT.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
76
Freescale Semiconductor
Thermal
20.2
Thermal Management Information
For the following sections, PD = (VDD x IDD) + PI/O where PI/O is the power dissipation of the I/O drivers.
20.2.1
Estimation of Junction Temperature with Junction-to-Ambient
Thermal Resistance
An estimation of the chip junction temperature, TJ, can be obtained from the equation:
TJ = TA + (RθJA × PD)
where:
TJ = junction temperature (°C)
TA = ambient temperature for the package (°C)
RθJA = junction to ambient thermal resistance (°C/W)
PD = power dissipation in the package (W)
The junction to ambient thermal resistance is an industry standard value that provides a quick and easy
estimation of thermal performance. As a general statement, the value obtained on a single layer board is
appropriate for a tightly packed printed circuit board. The value obtained on the board with the internal
planes is usually appropriate if the board has low power dissipation and the components are well separated.
Test cases have demonstrated that errors of a factor of two (in the quantity TJ – TA) are possible.
20.2.2
Estimation of Junction Temperature with Junction-to-Board
Thermal Resistance
The thermal performance of a device cannot be adequately predicted from the junction to ambient thermal
resistance. The thermal performance of any component is strongly dependent on the power dissipation of
surrounding components. In addition, the ambient temperature varies widely within the application. For
many natural convection and especially closed box applications, the board temperature at the perimeter
(edge) of the package will be approximately the same as the local air temperature near the device.
Specifying the local ambient conditions explicitly as the board temperature provides a more precise
description of the local ambient conditions that determine the temperature of the device.
At a known board temperature, the junction temperature is estimated using the following equation:
TJ = TB + (RθJB × PD)
where:
TJ = junction temperature (°C)
TB = board temperature at the package perimeter (°C)
RθJB = junction to board thermal resistance (°C/W) per JESD51–8
PD = power dissipation in the package (W)
When the heat loss from the package case to the air can be ignored, acceptable predictions of junction
temperature can be made. The application board should be similar to the thermal test condition: the
component is soldered to a board with internal planes.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
77
Thermal
20.2.3
Experimental Determination of Junction Temperature
To determine the junction temperature of the device in the application after prototypes are available, the
Thermal Characterization Parameter (ΨJT) can be used to determine the junction temperature with a
measurement of the temperature at the top center of the package case using the following equation:
TJ = TT + (ΨJT × PD)
where:
TJ = junction temperature (°C)
TT = thermocouple temperature on top of package (°C)
ΨJT = thermal characterization parameter (°C/W)
PD = power dissipation in the package (W)
The thermal characterization parameter is measured per JESD51-2 specification using a 40 gauge type T
thermocouple epoxied to the top center of the package case. The thermocouple should be positioned so
that the thermocouple junction rests on the package. A small amount of epoxy is placed over the
thermocouple junction and over about 1 mm of wire extending from the junction. The thermocouple wire
is placed flat against the package case to avoid measurement errors caused by cooling effects of the
thermocouple wire.
20.2.4
Heat Sinks and Junction-to-Case Thermal Resistance
In some application environments, a heat sink will be required to provide the necessary thermal
management of the device. When a heat sink is used, the thermal resistance is expressed as the sum of a
junction to case thermal resistance and a case to ambient thermal resistance:
RθJA = RθJC + RθCA
where:
RθJA = junction to ambient thermal resistance (°C/W)
RθJC = junction to case thermal resistance (°C/W)
RθCA = case to ambient thermal resistance (°C/W)
RθJC is device related and cannot be influenced by the user. The user controls the thermal environment to
change the case to ambient thermal resistance, RθCA. For instance, the user can change the size of the heat
sink, the air flow around the device, the interface material, the mounting arrangement on printed circuit
board, or change the thermal dissipation on the printed circuit board surrounding the device.
To illustrate the thermal performance of the devices with heat sinks, the thermal performance has been
simulated with a few commercially available heat sinks. The heat sink choice is determined by the
application environment (temperature, air flow, adjacent component power dissipation) and the physical
space available. Because there is not a standard application environment, a standard heat sink is not
required.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
78
Freescale Semiconductor
Thermal
Table 63. Heat Sinks and Junction-to-Case Thermal Resistance of MPC8313E (TEPBGAII)
35x35 mm TBGA
Heat Sink Assuming Thermal Grease
Air Flow
AAVID 30x30x9.4 mm Pin Fin
Natural Convection
10.7
AAVID 30x30x9.4 mm Pin Fin
1 m/s
6.2
AAVID 30x30x9.4 mm Pin Fin
2 m/s
5.3
AAVID 31x35x23 mm Pin Fin
Natural Convection
8.1
AAVID 31x35x23 mm Pin Fin
1 m/s
4.4
AAVID 31x35x23 mm Pin Fin
2 m/s
3.7
Wakefield, 53x53x25 mm Pin Fin
Natural Convection
5.4
Wakefield, 53x53x25 mm Pin Fin
1 m/s
3.2
Wakefield, 53x53x25 mm Pin Fin
2 m/s
2.4
MEI, 75x85x12 no adjacent board, extrusion
Natural Convection
6.4
MEI, 75x85x12 no adjacent board, extrusion
1 m/s
3.8
MEI, 75x85x12 no adjacent board, extrusion
2 m/s
2.5
MEI, 75x85x12 mm, adjacent board, 40 mm Side bypass
1 m/s
2.8
Junction-to-Ambient
Thermal Resistance
Accurate thermal design requires thermal modeling of the application environment using computational
fluid dynamics software which can model both the conduction cooling and the convection cooling of the
air moving through the application. Simplified thermal models of the packages can be assembled using the
junction-to-case and junction-to-board thermal resistances listed in the thermal resistance table. More
detailed thermal models can be made available on request.
Heat sink Vendors include the following list:
Aavid Thermalloy
80 Commercial St.
Concord, NH 03301
Internet: www.aavidthermalloy.com
603-224-9988
Alpha Novatech
473 Sapena Ct. #12
Santa Clara, CA 95054
Internet: www.alphanovatech.com
408-749-7601
International Electronic Research Corporation (IERC)
413 North Moss St.
Burbank, CA 91502
Internet: www.ctscorp.com
818-842-7277
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
79
Thermal
Millennium Electronics (MEI)
Loroco Sites
671 East Brokaw Road
San Jose, CA 95112
Internet: www.mei-thermal.com
408-436-8770
Tyco Electronics
Chip Coolers™
P.O. Box 3668
Harrisburg, PA 17105
Internet: www.chipcoolers.com
800-522-6752
Wakefield Engineering
33 Bridge St.
Pelham, NH 03076
Internet: www.wakefield.com
603-635-2800
Interface material vendors include the following:
20.3
Chomerics, Inc.
77 Dragon Ct.
Woburn, MA 01801
Internet: www.chomerics.com
781-935-4850
Dow-Corning Corporation
Corporate Center
PO BOX 994
Midland, MI 48686-0994
Internet: www.dowcorning.com
800-248-2481
Shin-Etsu MicroSi, Inc.
10028 S. 51st St.
Phoenix, AZ 85044
Internet: www.microsi.com
888-642-7674
The Bergquist Company
18930 West 78th St.
Chanhassen, MN 55317
Internet: www.bergquistcompany.com
800-347-4572
Heat Sink Attachment
When attaching heat sinks to these devices, an interface material is required. The best method is to use
thermal grease and a spring clip. The spring clip should connect to the printed circuit board, either to the
board itself, to hooks soldered to the board, or to a plastic stiffener. Avoid attachment forces which would
lift the edge of the package or peel the package from the board. Such peeling forces reduce the solder joint
lifetime of the package. Recommended maximum force on the top of the package is 10 lb (4.5 kg) force.
If an adhesive attachment is planned, the adhesive should be intended for attachment to painted or plastic
surfaces and its performance verified under the application requirements.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
80
Freescale Semiconductor
System Design Information
20.3.1
Experimental Determination of the Junction Temperature with a
Heat Sink
When heat sink is used, the junction temperature is determined from a thermocouple inserted at the
interface between the case of the package and the interface material. A clearance slot or hole is normally
required in the heat sink. Minimizing the size of the clearance is important to minimize the change in
thermal performance caused by removing part of the thermal interface to the heat sink. Because of the
experimental difficulties with this technique, many engineers measure the heat sink temperature and then
back calculate the case temperature using a separate measurement of the thermal resistance of the
interface. From this case temperature, the junction temperature is determined from the junction to case
thermal resistance.
TJ = TC + (RθJC x PD)
Where:
TJ = junction temperature (°C)
TC = case temperature of the package
RθJC = junction-to-case thermal resistance
PD = power dissipation
21 System Design Information
This section provides electrical and thermal design recommendations for successful application of the
MPC8313E SYS_CLK_IN
21.1
System Clocking
The MPC8313E includes two PLLs.
1. The platform PLL (AVDD2) generates the platform clock from the externally supplied
SYS_CLK_IN input in PCI host mode or SYS_CLK_IN/PCI_SYNC_IN in PCI agent mode. The
frequency ratio between the platform and SYS_CLK_IN is selected using the platform PLL ratio
configuration bits as described in Section 19.1, “System PLL Configuration.”
2. The e300 Core PLL (AVDD1) generates the core clock as a slave to the platform clock. The
frequency ratio between the e300 core clock and the platform clock is selected using the e300
PLL ratio configuration bits as described in Section 19.2, “Core PLL Configuration.”
21.2
PLL Power Supply Filtering
Each of the PLLs listed above is provided with power through independent power supply pins (AVDD1,
AVDD2 respectively). The AVDD level should always be equivalent to VDD, and preferably these voltages
will be derived directly from VDD through a low frequency filter scheme such as the following.
There are a number of ways to reliably provide power to the PLLs, but the recommended solution is to
provide five independent filter circuits as illustrated in Figure 40, one to each of the five AVDD pins. By
providing independent filters to each PLL the opportunity to cause noise injection from one PLL to the
other is reduced.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
81
System Design Information
This circuit is intended to filter noise in the PLLs resonant frequency range from a 500 kHz to 10 MHz
range. It should be built with surface mount capacitors with minimum Effective Series Inductance (ESL).
Consistent with the recommendations of Dr. Howard Johnson in High Speed Digital Design: A Handbook
of Black Magic (Prentice Hall, 1993), multiple small capacitors of equal value are recommended over a
single large value capacitor.
Each circuit should be placed as close as possible to the specific AVDD pin being supplied to minimize
noise coupled from nearby circuits. It should be possible to route directly from the capacitors to the AV DD
pin, which is on the periphery of package, without the inductance of vias.
Figure 40 shows the PLL power supply filter circuit.
10 Ω
V DD
AVDD (or L2AV DD)
2.2 µF
2.2 µF
VSS
Low ESL Surface Mount Capacitors
Figure 40. PLL Power Supply Filter Circuit
21.3
Decoupling Recommendations
Due to large address and data buses, and high operating frequencies, the device can generate transient
power surges and high frequency noise in its power supply, especially while driving large capacitive loads.
This noise must be prevented from reaching other components in the MPC8313E system, and the
MPC8313E itself requires a clean, tightly regulated source of power. Therefore, it is recommended that
the system designer place at least one decoupling capacitor at each VDD, NVDD, GVDD, LVDD, LVDDA,
and LVDDB pins of the device. These decoupling capacitors should receive their power from separate VDD,
NVDD, GVDD, LVDD, LVDDA, LVDDB and VSS power planes in the PCB, utilizing short traces to
minimize inductance. Capacitors may be placed directly under the device using a standard escape pattern.
Others may surround the part.
These capacitors should have a value of 0.01 or 0.1 µF. Only ceramic SMT (surface mount technology)
capacitors should be used to minimize lead inductance, preferably 0402 or 0603 sizes.
In addition, it is recommended that there be several bulk storage capacitors distributed around the PCB,
feeding the VDD, NVDD, GVDD, LVDD, LVDDA, and LVDDB planes, to enable quick recharging of the
smaller chip capacitors. These bulk capacitors should have a low ESR (equivalent series resistance) rating
to ensure the quick response time necessary. They should also be connected to the power and ground
planes through two vias to minimize inductance. Suggested bulk capacitors—100–330 µF (AVX TPS
tantalum or Sanyo OSCON).
21.4
Connection Recommendations
To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal
level. Unused active low inputs should be tied to NVDD, GVDD, LVDD, LVDDA or LVDDB as required.
Unused active high inputs should be connected to VSS. All NC (no-connect) signals must remain
unconnected.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
82
Freescale Semiconductor
System Design Information
Power and ground connections must be made to all external VDD, NVDD, GVDD, LVDD, LVDDA, LVDDB,
and VSS pins of the device.
21.5
Output Buffer DC Impedance
The MPC8313E drivers are characterized over process, voltage, and temperature. For all buses, the driver
is a push-pull single-ended driver type (open drain for I2C).
To measure Z0 for the single-ended drivers, an external resistor is connected from the chip pad to NVDD
or VSS. Then, the value of each resistor is varied until the pad voltage is NVDD/2 (see Figure 41). The
output impedance is the average of two components, the resistances of the pull-up and pull-down devices.
When data is held high, SW1 is closed (SW2 is open) and RP is trimmed until the voltage at the pad equals
NVDD/2. RP then becomes the resistance of the pull-up devices. RP and RN are designed to be close to each
other in value. Then, Z0 = (RP + RN)/2.
NVDD
RN
SW2
Data
Pad
SW1
RP
VSS
Figure 41. Driver Impedance Measurement
The value of this resistance and the strength of the driver’s current source can be found by making two
measurements. First, the output voltage is measured while driving logic 1 without an external differential
termination resistor. The measured voltage is V1 = Rsource × Isource. Second, the output voltage is measured
while driving logic 1 with an external precision differential termination resistor of value R term. The
measured voltage is V2 = (1/(1/R1 + 1/R2)) × Isource. Solving for the output impedance gives Rsource =
Rterm × (V1/V2 – 1). The drive current is then Isource = V1/Rsource.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
83
System Design Information
Table 64 summarizes the signal impedance targets. The driver impedance are targeted at minimum VDD,
nominal NVDD, 105°C.
Table 64. Impedance Characteristics
Impedance
Local Bus, Ethernet,
DUART, Control,
Configuration, Power
Management
PCI Signals
(not including PCI
output clocks)
PCI Output Clocks
(including
PCI_SYNC_OUT)
DDR DRAM
Symbol
Unit
RN
42 Target
25 Target
42 Target
20 Target
Z0
Ω
RP
42 Target
25 Target
42 Target
20 Target
Z0
Ω
Differential
NA
NA
NA
NA
ZDIFF
Ω
Note: Nominal supply voltages. See Table 1, Tj = 105°C.
21.6
Configuration Pin Muxing
The MPC8313E provides the user with power-on configuration options which can be set through the use
of external pull-up or pull-down resistors of 4.7 kΩ on certain output pins (see customer visible
configuration pins). These pins are generally used as output only pins in normal operation.
While HRESET is asserted however, these pins are treated as inputs. The value presented on these pins
while HRESET is asserted, is latched when PORESET deasserts, at which time the input receiver is
disabled and the I/O circuit takes on its normal function. Careful board layout with stubless connections
to these pull-up/pull-down resistors coupled with the large value of the pull-up/pull-down resistor should
minimize the disruption of signal quality or speed for output pins thus configured.
21.7
Pull-Up Resistor Requirements
The MPC8313E requires high resistance pull-up resistors (10 kΩ is recommended) on open drain type pins
including I2C pins, Ethernet Management MDIO pin and EPIC interrupt pins.
Correct operation of the JTAG interface requires configuration of a group of system control pins as
demonstrated in Figure 42. Care must be taken to ensure that these pins are maintained at a valid deasserted
state under normal operating conditions as most have asynchronous behavior and spurious assertion will
give unpredictable results.
Refer to the PCI 2.2 specification for all pull-ups required for PCI.
21.8
JTAG Configuration Signals
Boundary scan testing is enabled through the JTAG interface signals. The TRST signal is optional in
IEEE Std. 1149.1, but is provided on all processors that implement the PowerPC architecture. The device
requires TRST to be asserted during reset conditions to ensure the JTAG boundary logic does not interfere
with normal chip operation. While it is possible to force the TAP controller to the reset state using only the
TCK and TMS signals, generally systems will assert TRST during power-on reset. Because the JTAG
interface is also used for accessing the common on-chip processor (COP) function, simply tying TRST to
PORESET is not practical.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
84
Freescale Semiconductor
System Design Information
The COP function of these processors allows a remote computer system (typically, a PC with dedicated
hardware and debugging software) to access and control the internal operations of the processor. The COP
interface connects primarily through the JTAG port of the processor, with some additional status
monitoring signals. The COP port requires the ability to independently assert TRST without causing
PORESET. If the target system has independent reset sources, such as voltage monitors, watchdog timers,
power supply failures, or push-button switches, then the COP reset signals must be merged into these
signals with logic.
The arrangement shown in Figure 42 allows the COP to independently assert HRESET or TRST, while
ensuring that the target can drive HRESET as well. If the JTAG interface and COP header will not be used,
TRST should be tied to PORESET so that it is asserted when the system reset signal (PORESET) is
asserted.
The COP header shown in Figure 42 adds many benefits—breakpoints, watchpoints, register and memory
examination/modification, and other standard debugger features are possible through this interface—and
can be as inexpensive as an unpopulated footprint for a header to be added when needed.
The COP interface has a standard header for connection to the target system, based on the 0.025"
square-post, 0.100" centered header assembly (often called a Berg header).
There is no standardized way to number the COP header shown in Figure 42; consequently, many different
pin numbers have been observed from emulator vendors. Some are numbered top-to-bottom then
left-to-right, while others use left-to-right then top-to-bottom, while still others number the pins counter
clockwise from pin 1 (as with an IC). Regardless of the numbering, the signal placement recommended in
Figure 42 is common to all known emulators.
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
85
System Design Information
PORESET
PORESET
From Target
Board Sources
(if any)
SRESET
SRESET
HRESET
HRESET
13
11
10 kΩ
HRESET
NVDD
SRESET
NVDD
10 kΩ
NVDD
10 kΩ
NVDD
1
2
3
4
5
6
7
8
9
10
11
12
4
61
5
15
10 kΩ
TRST
VDD_SENSE
TRST
2 kΩ
NVDD
NC
CHKSTP_OUT
CHKSTP_OUT
10 kΩ
NVDD
14
KEY
13 No
pin
16
COP Connector
Physical Pin Out
NVDD
CHKSTP_IN
COP Header
15
10 kΩ
2
8
CHKSTP_IN
TMS
9
1
3
TMS
TDO
TDI
TDO
TDI
TCK
7
2
TCK
NC
10
NC
12
NC
16
Notes:
1. Some systems require power to be fed from the application board into the debugger repeater card
via the COP header. In this case the resistor value for VDD_SENSE should be around 20Ω.
2. Key location; pin 14 is not physically present on the COP header.
Figure 42. JTAG Interface Connection
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
86
Freescale Semiconductor
Document Revision History
22 Document Revision History
Table 22-61 provides a revision history for this hardware specification.
Table 65. Document Revision History
Revision
Date
0
06/2007
Substantive Change(s)
Initial release.
23 Ordering Information
Ordering information for the parts fully covered by this specification document is provided in
Section 23.1, “Part Numbers Fully Addressed by This Document.”
23.1 Part Numbers Fully Addressed by This Document
Table 66 provides the Freescale part numbering nomenclature for the MPC8313E. Note that the individual
part numbers correspond to a maximum processor core frequency. For available frequencies, contact your
local Freescale sales office. In addition to the processor frequency, the part numbering scheme also
includes an application modifier which may specify special application conditions. Each part number also
contains a revision code which refers to the die mask revision number.
Table 66. Part Numbering Nomenclature
MPC
nnnn
e
t
pp
aa
a
x
Product
Code
Part
Identifier
Encryption
Acceleration
Temperature
Range 3
Package 1
e300 core
Frequency 2
DDR
Frequency
Revision
Level
MPC
8313
Blank = 0 to 105°C
C= –40 to 105°C
VR= PB free
TEPBGAII
AF = 333MHz F = 333 MHz
Contact
local
Freescale
sales office
Blank = Not
included
E = included
Notes:
1. See Section 18, “Package and Pin Listings,” for more information on available package types.
2. Processor core frequencies supported by parts addressed by this specification only. Not all parts described in this
specification support all core frequencies. Additionally, parts addressed by Part Number Specifications may support other
maximum core frequencies.
3. Contact local Freescale office on availability of parts with C temperature range
MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
87
How to Reach Us:
Home Page:
www.freescale.com
email:
[email protected]
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
1-800-521-6274
480-768-2130
[email protected]
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
[email protected]
Freescale Semiconductor reserves the right to make changes without further notice to
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku
Tokyo 153-0064, Japan
0120 191014
+81 3 5437 9125
[email protected]
parameters, including “Typicals” must be validated for each customer application by
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate,
Tai Po, N.T., Hong Kong
+800 2666 8080
[email protected]
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor
For Literature Requests Only:
Freescale Semiconductor
Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447
303-675-2140
Fax: 303-675-2150
LDCForFreescaleSemiconductor
@hibbertgroup.com
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
The Power Architecture and Power.org word marks and the Power and Power.org logos
and related marks are trademarks and service marks licensed by Power.org. The
described product contains a PowerPC processor core. The PowerPC name is a
trademark of IBM Corp. and used under license. IEEE Stds. 802.1™, 802.11™,
802.2™, 802.3™, 1149.1™, and 1588™ are trademarks of the Institute of Electrical
and Electronics Engineers, Inc., (IEEE). This product is not endosed or approved by
the IEEE. All other product or service names are the property of their respective
owners.
Document Number: MPC8313EEC
Rev. 0
06/2007
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of
any product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters which may be
provided in Freescale Semiconductor data sheets and/or specifications can and do
vary in different applications and actual performance may vary over time. All operating
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Semiconductor was negligent regarding the design or manufacture of the part.
© Freescale Semiconductor, Inc., 2007.