Document 621-1 Coupled Inductors – MSD7342 For Flyback, SEPIC and other Applications • Tight coupling (k ≥ 0.97) and 200 V isolation make the MSD7342 series of coupled inductors ideal for use in a variety of circuits including flyback, multi-output buck and SEPIC. • They provide high inductance, high efficiency and excellent current handling in a rugged, low cost part. • Can also be used as two single inductors connected in series or parallel, as a common mode choke or as a 1 : 1 transformer. + + D L1 VIN C L2 C VOUT – SW – Typical Flyback Converter L2 D + C VOUT AUX – + 0.295 max 7,5 0.295 max 7,5 VIN 1 2 L1 L2 3 4 Recommended Land Pattern 0.110 2,8 0.091 2,3 2 1 0.063 1,6 Dimensions are in inches mm C VOUT – 0.083 2,1 If board traces are run in these areas, consider masking them to prevent shorting. 2 1 3 4 0.130 3,3 0.043 1,10 D + L1 VIN – 0.028 0,7 0.150 3,8 D Typical Buck Converter with auxiliary output 0.181 max 4,6 4 SW – Dot indicates pin 1 123 3 + L1 + C1 L2 Q C Typical SEPIC schematic VOUT – Core material Ferrite Core and winding loss Go to online calculator Terminations RoHS compliant matte tin over nickel over phos bronze. Other terminations available at additional cost. Weight 0.76 – 0.87g Ambient temperature –40°C to +85°C with Irms current, +85°C to +125°C with derated current Storage temperature Component: –40°C to +125°C. Tape and reel packaging: –40°C to +80°C Winding to winding isolation 200 Vrms Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 250/7″ reel; 1000/13″ reel Plastic tape: 16 mm wide, 0.4 mm thick, 12 mm pocket spacing, 4.9 mm pocket depth PCB washing Tested with pure water or alcohol only. For other solvents, see Doc787_PCB_Washing.pdf. [email protected] subject to change without notice. US +1-847-639-6400 Please check our website for latest information. UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Document 621-1 Revised 11/07/13 © Coilcraft Inc. 2013 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information. Document 621-2 Coupled Inductors – MSD7342 Series Isat (A)6 Irms (A) CouplingLeakage 2 3 4 5 Inductance DCR max SRF typ coefficient L typ 10% 20% 30% both one Part number1 windings7 winding8 ±20% (µH) (Ohms) (MHz) typ (µH) drop drop drop MSD7342-252ML_ 2.5 MSD7342-332ML_ 3.3 MSD7342-472ML_ 4.7 MSD7342-562ML_ 5.6 MSD7342-682ML_ 6.8 MSD7342-822ML_ 8.2 MSD7342-103ML_ 10 MSD7342-123ML_ 12 MSD7342-153ML_ 15 MSD7342-183ML_ 18 MSD7342-223ML_ 22 MSD7342-273ML_ 27 MSD7342-333ML_ 33 MSD7342-393ML_ 39 MSD7342-473ML_ 47 MSD7342-563ML_ 56 MSD7342-683ML_ 68 MSD7342-823ML_ 82 MSD7342-104ML_ 100 MSD7342-124ML_ 120 MSD7342-154ML_ 150 MSD7342-184ML_ 180 MSD7342-224ML_ 220 MSD7342-274ML_ 270 MSD7342-334ML_ 330 MSD7342-394ML_ 390 MSD7342-474ML_ 470 MSD7342-564ML_ 560 MSD7342-684ML_ 680 MSD7342-824ML_ 820 MSD7342-105ML_ 1000 0.033 55 0.037 43 0.051 35 0.063 32 0.070 30 0.075 27 0.100 22 0.120 20 0.130 18 0.170 15 0.220 13.5 0.250 12.0 0.270 11.0 0.380 10.0 0.420 9.5 0.460 8.7 0.600 7.3 0.680 6.2 0.770 5.5 1.03 4.5 1.35 4.0 1.52 3.8 1.72 3.5 2.41 3.3 2.70 3.0 3.05 2.8 4.00 2.6 4.43 2.5 5.00 2.3 6.80 2.2 7.80 2.0 0.97 0.99 0.99 0.99 0.99 0.98 0.98 0.98 0.98 >0.99 >0.99 >0.99 >0.99 0.99 >0.99 >0.99 >0.99 0.99 >0.99 >0.99 >0.99 >0.99 >0.99 >0.99 >0.99 0.99 0.99 >0.99 0.99 >0.99 >0.99 0.14 6.0 6.26.3 0.09 5.2 5.35.4 0.11 4.1 4.34.6 0.09 3.9 4.14.2 0.14 3.7 3.83.9 0.25 3.3 3.43.5 0.30 2.8 2.93.0 0.36 2.5 2.62.7 0.49 2.2 2.32.4 0.16 2.0 2.22.3 0.20 1.9 2.02.1 0.20 1.7 1.81.9 0.15 1.5 1.61.7 0.70 1.3 1.41.5 0.30 1.2 1.31.4 0.51 1.1 1.21.3 0.51 1.0 1.11.2 1.17 0.90 1.001.1 0.96 0.80 0.920.98 0.61 0.70 0.800.90 0.54 0.65 0.760.80 0.75 0.62 0.660.73 1.43 0.59 0.620.66 1.56 0.55 0.570.60 1.65 0.49 0.520.54 4.73 0.45 0.470.50 5.50 0.41 0.430.46 4.85 0.38 0.400.42 7.59 0.36 0.370.38 8.01 0.30 0.320.35 8.69 0.27 0.290.31 2.17 2.05 1.74 1.57 1.49 1.44 1.24 1.14 1.09 0.95 0.84 0.79 0.76 0.64 0.61 0.58 0.51 0.48 0.45 0.39 0.34 0.32 0.30 0.25 0.24 0.23 0.20 0.19 0.18 0.15 0.14 3.06 2.89 2.46 2.22 2.10 2.03 1.76 1.61 1.54 1.35 1.19 1.11 1.07 0.90 0.86 0.82 0.72 0.67 0.63 0.55 0.48 0.45 0.42 0.36 0.34 0.32 0.28 0.26 0.25 0.21 0.20 1. When ordering, please specify termination and packaging codes: Coupled Inductor Core and Winding Loss Calculator MSD7342-105MLC Termination:L=RoHS compliant matte tin over nickel over phos bronze. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging:C =7″ machine-ready reel. EIA-481 embossed plastic tape (250 parts per full reel). B=Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D =13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (1000 parts per full reel). 2. Inductance shown for each winding, measured at 100 kHz, 0.1 Vrms, 0 Adc on an Agilent/HP 4284A LCR meter or equivalent. When leads are connected in parallel, inductance is the same value. When leads are connected in series, inductance is four times the value. 3. DCR is for each winding. When leads are connected in parallel, DCR is half the value. When leads are connected in series, DCR is twice the value. 4. SRF measured using an Agilent/HP 4191A or equivalent. When leads are connected in parallel, SRF is the same value. 5. Leakage inductance is for L1 and is measured with L2 shorted. 6. DC current, at which the inductance drops the specified amount from its value without current. It is the sum of the current flowing in both windings. 7. Equal current when applied to each winding simultaneously that causes a 40°C temperature rise from 25°C ambient. See temperature rise calculation. 8. Maximum current when applied to one winding that causes a 40°C temperature rise from 25°C ambient. See temperature rise calculation. 9. Electrical specifications at 25°C. Refer to Doc 639 “Selecting Coupled Inductors for SEPIC Applications.” Refer to Doc 362 “Soldering Surface Mount Components” before soldering. This web-based utility allows you to enter frequency, peak-to-peak (ripple) current, and Irms current to predict temperature rise and overall losses, including core loss. Go to online calculator [email protected] subject to change without notice. US +1-847-639-6400 Please check our website for latest information. UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Document 621-2 Revised 11/07/13 Document 621-2 Revised 02/23/11 © Coilcraft Inc. 2013 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information. Document 621-3 Coupled Inductors – MSD7342 Series Typical L vs Current Typical L vs Frequency 10000 10000 1000 µH 100 µH 100 47 µH 10 µH 10 1000 µH 1000 470 µH Inductance (µH) Inductance (µH) 1000 470 µH 100 µH 100 47 µH 10 µH 10 4.7 µH 4.7 µH 1 0.01 1 0.1 10 1 0.1 Current (A) 1 10 100 Frequency (MHz) Irms Derating 120 110 90 80 70 60 50 40 25°C Percent of rated Irms 100 30 20 10 0 -40 -20 0 20 40 60 80 100 120 140 Ambient temperature (°C) [email protected] subject to change without notice. US +1-847-639-6400 Please check our website for latest information. UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Document 621-3 Revised 11/07/13 Document 621-3 Revised 02/23/11 © Coilcraft Inc. 2013 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information.