Target Displays Plug-on mount, enter key, manual format alignment Display LCD two lines, interface RS485 N 155 Features –– Target display for manual format aligning –– Display: LCD backlit, two lines –– One key permanently assigned as target –– Interface RS485 Technical data - mechanical design Voltage supply 24 VDC ±10 % Protection DIN EN 60529 IP 65 Current consumption ≤30 mA Operating temperature -10...+50 °C Display LCD, 7-segment display, 2-lines, backlit Storing temperature -20...+70 °C Display range -9999...+99999 Relative humidity 80 % non-condensing Interface RS485 (ASCII protocol) E-connection Data memory >10 years in EEPROM Programmable parameters Measuring unit mm/inch Direction arrows Decimal point Standard DIN EN 61010‑1 Overvoltage category II Protection class II Pollution degree 2 - Male/female connector M8, 4-pin - Cable output (30/15 cm) with male/female connector M8, 4-pin - Cable output (30/15 cm) with male/female connector M16, 5-pin Operation / keypad Emitted interference DIN EN 61000-6-3 Membrane with one softkey (handshake) Interference immunity DIN EN 61000-6-2 Housing type Surface mount housing with mounting plate Approval UL/cUL Dimensions W x H x L 37 x 75 x 29 mm Mounting Mount onto plate Weight approx. 60 g Material Polyamide black, UL 94V-0 1 www.baumerivo.com 30/10/2008 Technical data - electrical ratings Subject to modification in technic and design. Errors and omissions excepted. N 155 with connector output Target Displays Plug-on mount, enter key, manual format alignment Display LCD two lines, interface RS485 N 155 Part number N 155. 1 Description 3 B The multicon spindle positioning system is completed by a target display indicating also positions of hand wheels, limits, linear units etc in close vicinity of the actuator. The backlit LCD display provides the editing engineer with the target parameters. The handshake key is saving the edited parameters. Serial interface RS485 enables network of maximum 32 target and spindle position displays with PC or PLC. For complete solutions also memory controllers as decentralized operating and memory terminals are available. X01 Display B Horizontal at front Voltage supply 3 24 VDC E-connection 0 Connector output M8 with male and female connector 1 Bottom cable output M8 2 Rear cable output M8 3 Bottom cable output M16 Interface 1 RS485 Accessories Adaptor cable between cable connector M8 and female M16, 1 m Z 178.AW1 Cable connector M8, 4-pin, less cable with integrated terminating resistor 120 Ω Z 178.B01 Mating connector M8, 4-pin, less cable Z 178.D05 Data and supply cable M8, Master to N 150 and N 155, 5 m Z 178.S01 Cable connector M8, 4-pin, less cable Z 178.V01 Coupling cable 1 m between M8 and M8 2 www.baumerivo.com 30/10/2008 Z 178.A01 Subject to modification in technic and design. Errors and omissions excepted. Connectors and cables (page %S) Target Displays Plug-on mount, enter key, manual format alignment Display LCD two lines, interface RS485 N 155 Terminal assignment M8 connector M16 connector Assignment Pin 1 Pin 5 Tx/Rx-, RS485 Pin 2 Pin 4 Tx/Rx+, RS485 Pin 3 Pin 1 Sensor supply +24 V Pin 4 Pin 2 Sensor supply 0 V M8 connector 2 2 4 4 1 3 M16 connector 5 3 2 1 2 3 4 1 5 Subject to modification in technic and design. Errors and omissions excepted. 4 M16 female connector 3 www.baumerivo.com 30/10/2008 1 3 M8 female connector Target Displays Plug-on mount, enter key, manual format alignment Display LCD two lines, interface RS485 N 155 Dimensions Connector male and female Cable output rear, M8 4.3 29 75 36.5 ±0.18 12.5 11 37 8 PG gland with connector 16 PG gland with female connector Cutout for rear cable output Connector Female 16 connector 19 14 13 4 R5 15 36.5 ±0.1 16 M 30 10 10 Bottom cable output, M8 and M16 300 150 Female connector M8 300 150 16 Female connector M1 6 Connector M8 Connector M1 6 4 www.baumerivo.com 30/10/2008 Subject to modification in technic and design. Errors and omissions excepted. 14