ETC OX/ETAG/2/2KB

product information
contact memory tags
Features
● 2, 4, 8, 16, 32 or 64 k bytes of nonvolatile EEPROM
● Rugged construction to military
standards
● Asynchronous UART/RS232
compatible
● Unique 32 bit serial number
● Secure 64 bit password
● Selective memory write protection
● 16 bit CRC error correction
Oxley e-tags are contact memory
tags containing up-to 64 k bytes of
EEPROM non-volatile memory
housed in small rugged metal cans.
e-tags are intended for permanent
attachment to host assets in order
store any kind of digital information
relevant to the asset, creating a
secure portable micro-database coresident with the asset itself.
When interfaced to a host controller
an e-tag is capable of having its
memory read-from or written-to
virtually an unlimited number of
times. When disconnected from a
host controller the data stored can
be retained for over 100 years. etags are passive containing no
battery or internal power source to
retain data.
Physical protocol
Physical signalling between e-tag
and a host controller uses
asynchronous serial data compatible
with common integrated circuit
UARTs (universal asynchronous
receiver transmitter) operating in
'simplex' bi-directional mode at
57.6k bits per second.
this area. This can be used to lock
just a few bytes of EEPROM or the
whole e-tag. Once a lock has been
set it cannot be reversed. A lock
can be extended allowing data to be
protected as it is added.
Unique serial number
Each e-tag has a unique 32 bit serial
number stored in ROM which
cannot be altered or erased but can
be read by a host device.
Error correction
All host communications to and from
an e-tag contain a 16 bit cyclic
redundancy check (CRC) stored
within the communication packet.
For command messages sent by
the host controller, the host must
calculate the CRC value. On receipt
of the command packet the e-tag
will perform its own CRC calculation
and compare it to the contents of
the received packet CRC value. If
the two do not match then an error
code will be returned by the e-tag.
Secure password protection
e-tag contact memory has a true
password protection function
whereby a 64 bit password can be
set and stored securely in EEPROM.
If enabled, the password must be
supplied, for each tag, to access the
data. Prior to a password being set
a host device can access full
read/write functionality. Once a
password has been set on an e-tag
the host must provide a matching
password before further reading or
writing of EEPROM is permitted. A
previously set password can be
cleared by supplying a matching
existing password.
Memory write protection
Areas of EEPROM can be
permanently locked preventing
further writing of data but allowing
continued reading of the data from
Conversely, for response messages
the e-tag calculates the CRC and
places it in the response packet. On
receipt of the response packet the
host should perform its own CRC
calculation and compare it to the
contents of the received packet
CRC. If the two do not match then it
is the responsibility of the host to
take appropriate action.
A detailed interface specification is
available to integrators on request.
product information
Characteristics
Dimensions (mm)
EEPROM write cycles: 100,000 max
EEPROM Data Retention:
100 years @ 25˚C
3.3
0.25
0.25
3.3
Weight: <1g
Baud rate: 57.6 k bits/sec
ø10.7
ø10.7
ø13.7
ø13.7
2 x ø3.2
ø6
Maximum ratings
Operating temperature range
(read/write):
-55°C to +125°C
20 CRS
26
style 2
style 1
Storage temperature range:
-60°C to +150°C
Stresses above maximum ratings may cause permanent
damage. Exposure to maximum rating conditions for
extended periods may affect reliability.
Environmental
characteristics
Ordering
When ordering please specify
Change of temperature:
quantity and the following type
IEC 68-2-14 BS2011 Test Na
Ta = -55°C, Tb = +125°C, T1 =30 mins number
Damp heat:
MIL-STD-810E Method 507.3
Procedure III Agravated test
Bump:
IEC 68-2-9 BS2011 Test Eb
4000 bumps +/- 10 bumps
400m/S2 (40g)
Mechanical shock:
IEC 68-6-27 BS2011 Test Ea
1000m/S2 (100g), 6mSec
Half sinewave pulse
Vibration:
IEC 68-2-6 BS2011 Test Fc
10-2000Hz 200m/S2 (20g)
Low air pressure:
IEC 68-2-13 BS2011 Test M
40mBar, 30 minutes
OX/ETAG/ __
* / ___
** kB
*Package option:
1 - Style 1, adhesive mount
2 - Style 2, mechanical mount
**Data memory size:
2 - 2kB,
4 - 4KB,
8 - 8kB,
16 - 16kB,
32 - 32kB,
64 - 64kB,
For example:
Type number OX/ETAG/1/32kB
specifies a memory capacity of 32 k
bytes in an adhesive mounting style.
Sealing:
IEC 68-2-17 BS EN 60068-2-17
Test Qc
Method 2, t = 20 min liquid temp 125°C
©Copyright Oxley Developments Company Ltd
e-tag is a trademark of Oxley Developments
Company Ltd
Oxley Systems is a division of Oxley Developments
Company Ltd
OXLEY SYSTEMS
Priory Park, Ulverston, Cumbria,
England. LA12 9QG
telephone: +44 (1229) 483285
fax: +44 (1229) 483263
e-mail: [email protected]
OXLEY INC.
Salt mist:
IEC 68-2-52 Test Kb severity 3
25 Business Park Drive,
Branford CT 06405 USA
telephone: (00) 1 (203) 488-1033
fax: (00) 1 (203) 481-6971
e-mail: [email protected]
Solvent resistance:
IEC69-2-45 BSEN60069-2-45 Test Xa
EMC: Def- Stan 59-41
ESD: MIL-STD-883E
Company Approvals: BS EN 9001:1994 and
QAS/34/61 REG No. FM 01759
CECC Approval No. M/0022, BS 9000
Approval No. 1048/M
ODC:SMOS:40528/4-2/2002
www.oxleygroup.com/systems/