PHILIPS P89LPC9151FDH

P89LPC9151/9161/9171
8-bit microcontroller with accelerated two-clock 80C51 core,
2 kB 3 V byte-erasable flash with 8-bit ADC
Rev. 02 — 9 February 2010
Product data sheet
1. General description
The P89LPC9151/9161/9171 is a single-chip microcontroller, available in low cost
packages, based on a high performance processor architecture that executes instructions
in two to four clocks, six times the rate of standard 80C51 devices. Many system-level
functions have been incorporated into the device in order to reduce component count,
board space, and system cost.
2. Features
2.1 Principal features
2 kB byte-erasable flash code memory organized into 256-byte sectors and 16-byte
pages. Single-byte erasing allows any byte(s) to be used as non-volatile data storage.
256-byte RAM data memory.
4-input multiplexed 8-bit ADC/single DAC output. Two analog comparators with
selectable inputs and reference source.
Two 16-bit counter/timers. Timer 0 (and Timer 1 - P89LPC9171) may be configured to
toggle a port output upon timer overflow or to become a PWM output.
A 23-bit system timer that can also be used as real-time clock consisting of a 7-bit
prescaler and a programmable and readable 16-bit timer.
Enhanced UART with a fractional baud rate generator, break detect, framing error
detection, and automatic address detection; 400 kHz byte-wide I2C-bus
communication port.
SPI communication port (P89LPC9161).
2.4 V to 3.6 V VDD operating range. I/O pins are 5 V tolerant (may be pulled up or
driven to 5.5 V).
Enhanced low voltage (brownout) detect allows a graceful system shutdown when
power fails.
16-pin TSSOP with 12 I/O pins minimum and up to 14 I/O pins while using on-chip
oscillator and reset options (P89LPC9161/9171), and 14-pin TSSOP packages with 10
I/O pins minimum and up to 12 I/O pins while using on-chip oscillator and reset options
(P89LPC9151).
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
2.2 Additional features
A high performance 80C51 CPU provides instruction cycle times of 111 ns to 222 ns
for all instructions except multiply and divide when executing at 18 MHz. This is six
times the performance of the standard 80C51 running at the same clock frequency. A
lower clock frequency for the same performance results in power savings and reduced
EMI.
In-Application Programming (IAP-Lite) and byte erase allows code memory to be used
for non-volatile data storage.
Serial flash In-Circuit Programming (ICP) allows simple production coding with
commercial EPROM programmers. Flash security bits prevent reading of sensitive
application programs.
Watchdog timer with separate on-chip oscillator, nominal 400 kHz, calibrated to ±5 %,
requiring no external components. The watchdog prescaler is selectable from
eight values.
High-accuracy internal RC oscillator option, with clock doubler option, allows operation
without external oscillator components. The RC oscillator option is selectable and fine
tunable.
Clock switching on the fly among internal RC oscillator, watchdog oscillator, external
clock input provides optimal support of minimal power active mode with fast switching
to maximum performance.
Idle and two different power-down reduced power modes. Improved wake-up from
Power-down mode (a LOW interrupt input starts execution). Typical power-down
current is 1 μA (total power-down with voltage comparators disabled).
Active-LOW reset. On-chip power-on reset allows operation without external reset
components. A software reset function is also available.
Configurable on-chip oscillator with frequency range options selected by user
programmed flash configuration bits. Oscillator options support frequencies from
20 kHz to the maximum operating frequency of 18 MHz.
Oscillator fail detect. The watchdog timer has a separate fully on-chip oscillator
allowing it to perform an oscillator fail detect function.
Programmable port output configuration options: quasi-bidirectional, open drain,
push-pull, input-only.
High current sourcing/sinking (20 mA) at 4 I/O pins on the P89LPC9151, 3 I/O pins on
the P89LPC9161 and 5 I/O pins on the P89LPC9171. All other port pins have high
sinking capability (20 mA). A maximum limit is specified for the entire chip.
Port ‘input pattern match’ detect. Port 0 may generate an interrupt when the value of
the pins match or do not match a programmable pattern.
Controlled slew rate port outputs to reduce EMI. Outputs have approximately 10 ns
minimum ramp times.
Only power and ground connections are required to operate the
P89LPC9151/9161/9171 when internal reset option is selected.
Four interrupt priority levels.
Five/six keypad interrupt inputs, plus two additional external interrupt inputs.
Schmitt trigger port inputs.
Second data pointer.
Emulation support.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
2 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
3. Ordering information
Table 1.
Ordering information
Type number
Package
Name
Description
Version
P89LPC9151FDH
TSSOP14
plastic thin shrink small outline package; 14
leads; body width 4.4 mm
SOT402-1
P89LPC9161FDH
TSSOP16
plastic thin shrink small outline package; 16
leads; body width 4.4 mm
SOT403-1
P89LPC9171FDH
TSSOP16
plastic thin shrink small outline package; 16
leads; body width 4.4 mm
SOT403-1
3.1 Ordering options
Table 2.
Ordering options
Type number
Flash memory
Temperature range
Frequency
P89LPC9151FDH
2 kB
−40 °C to +85 °C
0 MHz to 18 MHz
P89LPC9161FDH
2 kB
−40 °C to +85 °C
0 MHz to 18 MHz
P89LPC9171FDH
2 kB
−40 °C to +85 °C
0 MHz to 18 MHz
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
3 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
4. Block diagram
P89LPC9151
HIGH PERFORMANCE
ACCELERATED 2-CLOCK 80C51 CPU
TXD
2 kB CODE FLASH
UART
RXD
internal bus
SCL
I2 C
256 BYTE DATA RAM
SDA
P1[5:0]
PORT 1
CONFIGURABLE I/O
ADC1/DAC1
P0[5:0]
PORT 0
CONFIGURABLE I/O
REAL TIME CLOCK/
SYSTEM TIMER
AD10
AD11
AD12
AD13
DAC1
TIMER 0
TIMER 1
T0
KEYPAD INTERRUPT
ANALOG
COMPARATORS
WATCHDOG TIMER
AND OSCILLATOR
PROGRAMMABLE
OSCILLATOR DIVIDER
CMP2
CIN2B
CIN2A
CIN1A
CIN1B
CMPREF
CPU clock
POWER MONITOR
(POWER-ON RESET,
BROWNOUT RESET)
external clock
input
ON-CHIP RC
OSCILLATOR
ON-CHIP RC OSCILLATOR
WITH CLOCK DOUBLER
002aae564
Fig 1.
Block diagram (P89LPC9151)
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
4 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
P89LPC9161
HIGH PERFORMANCE
ACCELERATED 2-CLOCK 80C51 CPU
TXD
2 kB CODE FLASH
UART
RXD
internal bus
SCL
I2C
256 BYTE DATA RAM
SDA
P2[5:2]
PORT 2
CONFIGURABLE I/O
ADC1/DAC1
P1.5, P1[3:0]
PORT 1
CONFIGURABLE I/O
SPI
P0[5:1]
PORT 0
CONFIGURABLE I/O
REAL TIME CLOCK/
SYSTEM TIMER
AD10
AD11
AD12
AD13
DAC1
SPICLK
MOSI
MISO
SS
TIMER 0
TIMER 1
T0
KEYPAD INTERRUPT
WATCHDOG TIMER
AND OSCILLATOR
PROGRAMMABLE
OSCILLATOR DIVIDER
CIN2B
CIN2A
CIN1A
CIN1B
CMPREF
ANALOG
COMPARATORS
CPU clock
POWER MONITOR
(POWER-ON RESET,
BROWNOUT RESET)
external clock
input
ON-CHIP RC
OSCILLATOR
ON-CHIP RC OSCILLATOR
WITH CLOCK DOUBLER
002aae565
Fig 2.
Block diagram (P89LPC9161)
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
5 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
P89LPC9171
HIGH PERFORMANCE
ACCELERATED 2-CLOCK 80C51 CPU
TXD
2 kB CODE FLASH
UART
RXD
internal bus
SCL
I2C
256 BYTE DATA RAM
SDA
P2.2
PORT 2
CONFIGURABLE I/O
ADC1/DAC1
P1[5:0]
PORT 1
CONFIGURABLE I/O
REAL TIME CLOCK/
SYSTEM TIMER
P0.7, P[5:0]
PORT 0
CONFIGURABLE I/O
TIMER 0
TIMER 1
T0
T1
CMP2
CIN2B
CIN2A
CIN1A
CIN1B
CMPREF
ANALOG
COMPARATORS
KEYPAD INTERRUPT
WATCHDOG TIMER
AND OSCILLATOR
PROGRAMMABLE
OSCILLATOR DIVIDER
AD10
AD11
AD12
AD13
DAC1
POWER MONITOR
(POWER-ON RESET,
BROWNOUT RESET)
CPU clock
external clock
input
ON-CHIP RC
OSCILLATOR
ON-CHIP RC OSCILLATOR
WITH CLOCK DOUBLER
clkout
002aae566
Fig 3.
Block diagram (P89LPC9171)
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
6 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
5. Functional diagram
VDD
DAC1
VSS
KBI0
CMP2
TXD
AD10
KBI1
CIN2B
RXD
AD11
KBI2
CIN2A
AD12
KBI3
CIN1B
AD13
KBI4
CIN1A
INT1
CLKIN
KBI5
CMPREF
RST
PORT 0
P89LPC9151
PORT 1
T0
SCL
INT0
SDA
002aae567
Fig 4.
Functional diagram (P89LPC9151)
VDD
VSS
TXD
DAC1
AD10
KBI1
CIN2B
AD11
KBI2
CIN2A
AD12
KBI3
CIN1B
AD13
KBI4
CIN1A
CLKIN
KBI5
CMPREF
RXD
PORT 1
PORT 0
P89LPC9161
T0
SCL
INT0
SDA
RST
MOSI
MIS0
PORT 2
SS
SPICLK
002aae568
Fig 5.
Functional diagram (P89LPC9161)
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
7 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
VDD
DAC1
VSS
KBI0
CMP2
TXD
AD10
KBI1
CIN2B
RXD
AD11
KBI2
CIN2A
AD12
KBI3
CIN1B
AD13
KBI4
CIN1A
INT1
CLKIN
KBI5
CMPREF
RST
CLKOUT
KBI7
T1
PORT 0
PORT 1
P89LPC9171
T0
SCL
INT0
SDA
PORT 2
002aae569
Fig 6.
Functional diagram (P89LPC9171)
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
8 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
6. Pinning information
6.1 Pinning
P0.1/CIN2B/KBI1/AD10
1
14 P0.2/CIN2A/KBI2/AD11
P0.0/CMP2/KBI0
2
13 P0.3/CIN1B/KBI3/AD12
P1.5/RST
3
VSS
4
P1.4/INT1
5
10 VDD
P1.3/INT0/SDA
6
9
P1.0/TXD
P1.2/T0/SCL
7
8
P1.1/RXD
12 P0.4/CIN1A/KBI4/AD13/DAC1
P89LPC9151
11 P0.5/CMPREF/KBI5/CLKIN
002aae570
Fig 7.
P89LPC9151 TSSOP14 pin configuration
P0.1/CIN2B/KBI1/AD10
1
16 P0.2/CIN2A/KBI2/AD11
P2.4/SS
2
15 P0.3/CIN1B/KBI3/AD12
P1.5/RST
3
14 P0.4/CIN1A/KBI4/AD13/DAC1
VSS
4
P2.3/MISO
5
P2.2/MOSI
6
11 P2.5/SPICLK
P1.3/INT0/SDA
7
10 P1.0/TXD
P1.2/T0/SCL
8
P89LPC9161
13 P0.5/CMPREF/KBI5/CLKIN
12 VDD
9
P1.1/RXD
002aae571
Fig 8.
P89LPC9161 TSSOP16 pin configuration
P0.1/CIN2B/KBI1/AD10
1
16 P0.2/CIN2A/KBI2/AD11
P0.0/CMP2/KBI0
2
15 P0.3/CIN1B/KBI3/AD12
P1.5/RST
3
14 P0.4/CIN1A/KBI4/AD13/DAC1
VSS
4
P2.2
5
P1.4/INT1
6
11 P0.7/T1/KBI7/CLKOUT
P1.3/INT0/SDA
7
10 P1.0/TXD
P1.2/T0/SCL
8
P89LPC9171
13 P0.5/CMPREF/KBI5/CLKIN
12 VDD
9
P1.1/RXD
002aae572
Fig 9.
P89LPC9171 TSSOP16 pin configuration
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
9 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
6.2 Pin description
Table 3.
P89LPC9151 Pin description
Symbol
Pin
Type Description
TSSOP14
P0.0 to P0.5
I/O
Port 0: Port 0 is an 6-bit I/O port with a user-configurable output type. During
reset Port 0 latches are configured in the input only mode with the internal pull-up
disabled. The operation of Port 0 pins as inputs and outputs depends upon the
port configuration selected. Each port pin is configured independently. Refer to
Section 7.15.1 “Port configurations” and Table 16 “Static characteristics” for
details.
The Keypad Interrupt feature operates with Port 0 pins.
All pins have Schmitt trigger inputs.
Port 0 also provides various special functions as described below:
P0.0/CMP2/
KBI0
P0.1/CIN2B/
KBI1/AD10
P0.2/CIN2A/
KBI2/AD11
P0.3/CIN1B/
KBI3/AD12
P0.4/CIN1A/
KBI4/DAC1/AD13
P0.5/CMPREF/
KBI5
P1.0 to P1.5
2
1
14
13
12
11
I/O
P0.0 — Port 0 bit 0.
O
CMP2 — Comparator 2 output
I
KBI0 — Keyboard input 0.
I/O
P0.1 — Port 0 bit 1.
I
CIN2B — Comparator 2 positive input B.
I
KBI1 — Keyboard input 1.
I
AD10 — ADC1 channel 0 analog input.
I/O
P0.2 — Port 0 bit 2.
I
CIN2A — Comparator 2 positive input A.
I
KBI2 — Keyboard input 2.
I
AD11 — ADC1 channel 1 analog input.
I/O
P0.3 — Port 0 bit 3. High current source.
I
CIN1B — Comparator 1 positive input B.
I
KBI3 — Keyboard input 3.
I
AD12 — ADC1 channel 2 analog input.
I/O
P0.4 — Port 0 bit 4. High current source.
I
CIN1A — Comparator 1 positive input A.
I
KBI4 — Keyboard input 4.
O
DAC1 — Digital-to-analog converter output 1.
I
AD13 — ADC1 channel 3 analog input.
I/O
P0.5 — Port 0 bit 5. High current source.
I
CMPREF — Comparator reference (negative) input.
I
KBI5 — Keyboard input 5.
I
CLKIN — External clock input.
I/O, I
Port 1: Port 1 is an 6-bit I/O port with a user-configurable output type, except for
three pins as noted below. During reset Port 1 latches are configured in the input
only mode with the internal pull-up disabled. The operation of the configurable
Port 1 pins as inputs and outputs depends upon the port configuration selected.
Each of the configurable port pins are programmed independently. Refer to
Section 7.15.1 “Port configurations” and Table 16 “Static characteristics” for
details. P1.2 to P1.3 are open drain when used as outputs. P1.5 is input only.
[1]
All pins have Schmitt trigger inputs.
Port 1 also provides various special functions as described below:
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
10 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
Table 3.
P89LPC9151 Pin description
Symbol
Pin
Type Description
TSSOP14
P1.0/TXD
P1.1/RXD
P1.2/T0/SCL
P1.3/INT0/SDA
P1.4/INT1
P1.5/RST
9
8
7
6
5
3
I/O
P1.0 — Port 1 bit 0.
O
TXD — Transmitter output for serial port.
I/O
P1.1 — Port 1 bit 1.
I
RXD — Receiver input for serial port.
I/O
P1.2 — Port 1 bit 2 (open-drain when used as output).
I/O
T0 — Timer/counter 0 external count input or overflow output (open-drain when
used as output).
I/O
SCL — I2C-bus serial clock input/output.
I/O
P1.3 — Port 1 bit 3 (open-drain when used as output).
I
INT0 — External interrupt 0 input.
I/O
SDA — I2C-bus serial data input/output.
I/O
P1.4 — Port 1 bit 4. High current source.
I
INT1 — External interrupt 1 input.
I
P1.5 — Port 1 bit 5 (input only).
I
RST — External Reset input during power-on or if selected via UCFG1. When
functioning as a reset input, a LOW on this pin resets the microcontroller, causing
I/O ports and peripherals to take on their default states, and the processor begins
execution at address 0. Also used during a power-on sequence to force ISP
mode.
VSS
4
I
Ground: 0 V reference.
VDD
10
I
Power supply: This is the power supply voltage for normal operation as well as
Idle and Power-down modes.
[1]
Input/output for P1.0 to P1.4. Input for P1.5.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
11 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
Table 4.
P89LPC9161 Pin description
Symbol
Pin
Type Description
TSSOP16
P0.1 to P0.5
I/O
Port 0: Port 0 is an 5-bit I/O port with a user-configurable output type. During
reset Port 0 latches are configured in the input only mode with the internal pull-up
disabled. The operation of Port 0 pins as inputs and outputs depends upon the
port configuration selected. Each port pin is configured independently. Refer to
Section 7.15.1 “Port configurations” and Table 16 “Static characteristics” for
details.
The Keypad Interrupt feature operates with Port 0 pins.
All pins have Schmitt trigger inputs.
Port 0 also provides various special functions as described below:
P0.1/CIN2B/
KBI1/AD10
P0.2/CIN2A/
KBI2/AD11
P0.3/CIN1B/
KBI3/AD12
P0.4/CIN1A/
KBI4/DAC1/AD13
P0.5/CMPREF/
KBI5
1
16
15
14
13
P1.0 to P1.3, P1.5
I/O
P0.1 — Port 0 bit 1.
I
CIN2B — Comparator 2 positive input B.
I
KBI1 — Keyboard input 1.
I
AD10 — ADC1 channel 0 analog input.
I/O
P0.2 — Port 0 bit 2.
I
CIN2A — Comparator 2 positive input A.
I
KBI2 — Keyboard input 2.
I
AD11 — ADC1 channel 1 analog input.
I/O
P0.3 — Port 0 bit 3. High current source.
I
CIN1B — Comparator 1 positive input B.
I
KBI3 — Keyboard input 3.
I
AD12 — ADC1 channel 2 analog input.
I/O
P0.4 — Port 0 bit 4. High current source.
I
CIN1A — Comparator 1 positive input A.
I
KBI4 — Keyboard input 4.
O
DAC1 — Digital-to-analog converter output 1.
I
AD13 — ADC1 channel 3 analog input.
I/O
P0.5 — Port 0 bit 5. High current source.
I
CMPREF — Comparator reference (negative) input.
I
KBI5 — Keyboard input 5.
I
CLKIN — External clock input.
I/O, I
Port 1: Port 1 is an 5-bit I/O port with a user-configurable output type, except for
three pins as noted below. During reset Port 1 latches are configured in the input
only mode with the internal pull-up disabled. The operation of the configurable
Port 1 pins as inputs and outputs depends upon the port configuration selected.
Each of the configurable port pins are programmed independently. Refer to
Section 7.15.1 “Port configurations” and Table 16 “Static characteristics” for
details. P1.2 to P1.3 are open drain when used as outputs. P1.5 is input only.
[1]
All pins have Schmitt trigger inputs.
Port 1 also provides various special functions as described below:
P1.0/TXD
P1.1/RXD
10
9
I/O
P1.0 — Port 1 bit 0.
O
TXD — Transmitter output for serial port.
I/O
P1.1 — Port 1 bit 1.
I
RXD — Receiver input for serial port.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
12 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
Table 4.
P89LPC9161 Pin description
Symbol
Pin
Type Description
TSSOP16
P1.2/T0/SCL
P1.3/INT0/SDA
P1.5/RST
8
7
3
P2.2 to P2.5
I/O
P1.2 — Port 1 bit 2 (open-drain when used as output).
I/O
T0 — Timer/counter 0 external count input or overflow output (open-drain when
used as output).
I/O
SCL — I2C-bus serial clock input/output.
I/O
P1.3 — Port 1 bit 3 (open-drain when used as output).
I
INT0 — External interrupt 0 input.
I/O
SDA — I2C-bus serial data input/output.
I
P1.5 — Port 1 bit 5 (input only).
I
RST — External Reset input during power-on or if selected via UCFG1. When
functioning as a reset input, a LOW on this pin resets the microcontroller, causing
I/O ports and peripherals to take on their default states, and the processor begins
execution at address 0. Also used during a power-on sequence to force ISP
mode.
I/O
Port 2: Port 2 is an 4-bit I/O port with a user-configurable output type. During
reset Port 2 latches are configured in the input only mode with the internal pull-up
disabled. The operation of Port 2 pins as inputs and outputs depends upon the
port configuration selected. Each port pin is configured independently. Refer to
Section 7.15 “I/O ports” for details.
All pins have Schmitt trigger inputs.
Port 2 also provides various special functions as described below:
P2.2/MOSI
P2.3/MISO
P2.4/SS
P2.5/SPICLK
6
5
2
11
I/O
P2.2 — Port 2 bit 2.
I/O
MOSI — SPI master out slave in. When configured as master, this pin is output;
when configured as slave, this pin is input.
I/O
P2.3 — Port 2 bit 3.
I/O
MISO — When configured as master, this pin is input, when configured as slave,
this pin is output.
I/O
P2.4 — Port 2 bit 4.
I
SS — SPI Slave select.
I/O
P2.5 — Port 2 bit 5.
I/O
SPICLK — SPI clock. When configured as master, this pin is output; when
configured as slave, this pin is input.
VSS
4
I
Ground: 0 V reference.
VDD
12
I
Power supply: This is the power supply voltage for normal operation as well as
Idle and Power-down modes.
[1]
Input/output for P1.0 to P1.3. Input for P1.5.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
13 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
Table 5.
P89LPC9171 Pin description
Symbol
Pin
Type Description
TSSOP16
P0.0 to P0.5, P0.7
I/O
Port 0: Port 0 is an 6-bit I/O port with a user-configurable output type. During
reset Port 0 latches are configured in the input only mode with the internal pull-up
disabled. The operation of Port 0 pins as inputs and outputs depends upon the
port configuration selected. Each port pin is configured independently. Refer to
Section 7.15.1 “Port configurations” and Table 16 “Static characteristics” for
details.
The Keypad Interrupt feature operates with Port 0 pins.
All pins have Schmitt trigger inputs.
Port 0 also provides various special functions as described below:
P0.0/CMP2/
KBI0
P0.1/CIN2B/
KBI1/AD10
P0.2/CIN2A/
KBI2/AD11
P0.3/CIN1B/
KBI3/AD12
P0.4/CIN1A/
KBI4/DAC1/AD13
P0.5/CMPREF/
KBI5/CLKIN
P0.7/T1/KBI7/CLK
OUT
2
1
16
15
14
13
11
I/O
P0.0 — Port 0 bit 0.
O
CMP2 — Comparator 2 output
I
KBI0 — Keyboard input 0.
I/O
P0.1 — Port 0 bit 1.
I
CIN2B — Comparator 2 positive input B.
I
KBI1 — Keyboard input 1.
I
AD10 — ADC1 channel 0 analog input.
I/O
P0.2 — Port 0 bit 2.
I
CIN2A — Comparator 2 positive input A.
I
KBI2 — Keyboard input 2.
I
AD11 — ADC1 channel 1 analog input.
I/O
P0.3 — Port 0 bit 3. High current source.
I
CIN1B — Comparator 1 positive input B.
I
KBI3 — Keyboard input 3.
I
AD12 — ADC1 channel 2 analog input.
I/O
P0.4 — Port 0 bit 4. High current source.
I
CIN1A — Comparator 1 positive input A.
I
KBI4 — Keyboard input 4.
O
DAC1 — Digital-to-analog converter output 1.
I
AD13 — ADC1 channel 3 analog input.
I/O
P0.5 — Port 0 bit 5. High current source.
I
CMPREF — Comparator reference (negative) input.
I
KBI5 — Keyboard input 5.
I
CLKIN — External clock input.
I/O
P0.7 — Port 0 bit 7. High current source.
I/O
T1 — Timer/counter 1 external count input or overflow output.
I
KBI7 — Keyboard input 7.
O
CLKOUT — Clock output.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
14 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
Table 5.
P89LPC9171 Pin description
Symbol
Pin
Type Description
TSSOP16
P1.0 to P1.5
I/O, I
[1]
Port 1: Port 1 is an 6-bit I/O port with a user-configurable output type, except for
three pins as noted below. During reset Port 1 latches are configured in the input
only mode with the internal pull-up disabled. The operation of the configurable
Port 1 pins as inputs and outputs depends upon the port configuration selected.
Each of the configurable port pins are programmed independently. Refer to
Section 7.15.1 “Port configurations” and Table 16 “Static characteristics” for
details. P1.2 to P1.3 are open drain when used as outputs. P1.5 is input only.
All pins have Schmitt trigger inputs.
Port 1 also provides various special functions as described below:
P1.0/TXD
10
P1.1/RXD
9
P1.2/T0/SCL
8
P1.3/INT0/SDA
P1.4/INT1
P1.5/RST
P2.2
7
6
3
5
I/O
P1.0 — Port 1 bit 0.
O
TXD — Transmitter output for serial port.
I/O
P1.1 — Port 1 bit 1.
I
RXD — Receiver input for serial port.
I/O
P1.2 — Port 1 bit 2 (open-drain when used as output).
I/O
T0 — Timer/counter 0 external count input or overflow output (open-drain when
used as output).
I/O
SCL — I2C-bus serial clock input/output.
I/O
P1.3 — Port 1 bit 3 (open-drain when used as output).
I
INT0 — External interrupt 0 input.
I/O
SDA — I2C-bus serial data input/output.
I/O
P1.4 — Port 1 bit 4. High current source.
I
INT1 — External interrupt 1 input.
I
P1.5 — Port 1 bit 5 (input only).
I
RST — External Reset input during power-on or if selected via UCFG1. When
functioning as a reset input, a LOW on this pin resets the microcontroller, causing
I/O ports and peripherals to take on their default states, and the processor begins
execution at address 0. Also used during a power-on sequence to force ISP
mode.
I/O
Port 2: P2.2 is a single-bit I/O port with a user-configurable output type. During
reset P2.2 latch is configured in the input only mode with the internal pull-up
disabled. The operation of the output depends upon the port configuration
selected. Refer to Section 7.15 “I/O ports” for details.
This pin has Schmitt trigger inputs.
VSS
4
I
Ground: 0 V reference.
VDD
12
I
Power supply: This is the power supply voltage for normal operation as well as
Idle and Power-down modes.
[1]
Input/output for P1.0 to P1.4. Input for P1.5.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
15 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
7. Functional description
Remark: Please refer to the P89LPC9151/9161/9171 User manual for a more detailed
functional description.
7.1 Special function registers
Remark: SFR accesses are restricted in the following ways:
• User must not attempt to access any SFR locations not defined.
• Accesses to any defined SFR locations must be strictly for the functions for the SFRs.
• SFR bits labeled ‘-’, ‘0’ or ‘1’ can only be written and read as follows:
– ‘-’ Unless otherwise specified, must be written with ‘0’, but can return any value
when read (even if it was written with ‘0’). It is a reserved bit and may be used in
future derivatives.
– ‘0’ must be written with ‘0’, and will return a ‘0’ when read.
– ‘1’ must be written with ‘1’, and will return a ‘1’ when read.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
16 of 91
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
NXP Semiconductors
P89LPC9151_61_71_2
Product data sheet
Table 6.
Special function registers - P89LPC9151
* indicates SFRs that are bit addressable.
Name
Description
SFR Bit functions and addresses
addr.
MSB
Bit address
E7
E6
Reset value
LSB
E5
E4
E3
E2
E1
Hex
Binary
00
0000 0000
E0
E0H
ADCON1
A/D control
register 1
97H
ENBI1
ENADCI1
TMM1
EDGE1
ADCI1
ENADC1
ADCS11
ADCS10
00
0000 0000
ADINS
A/D input
select
A3H
AIN13
AIN12
AIN11
AIN10
-
-
-
-
00
0000 0000
ADMODA
A/D mode
register A
C0H
BNDI1
BURST1
SCC1
SCAN1
-
-
-
-
00
0000 0000
ADMODB
A/D mode
register B
A1H
CLK2
CLK1
CLK0
INBND0
ENDAC1
-
BSA1
-
00
000x 0000
AD1BH
A/D_0
boundary high
register
C4H
FF
1111 1111
AD1BL
A/D_0
boundary low
register
BCH
00
0000 0000
AD1DAT0
A/D_0 data
register 0
D5H
00
0000 0000
AD1DAT1
A/D_0 data
register 1
D6H
00
0000 0000
AD1DAT2
A/D_0 data
register 2
D7H
00
0000 0000
AD1DAT3
A/D_0 data
register 3
F5H
00
0000 0000
AUXR1
Auxiliary
function
register
A2H
00
0000 00x0
17 of 91
© NXP B.V. 2010. All rights reserved.
Bit address
CLKLP
EBRR
-
ENT0
SRST
0
-
DPS
F7
F6
F5
F4
F3
F2
F1
F0
B*
B register
F0H
00
0000 0000
BRGR0[2]
Baud rate
generator 0
rate low
BEH
00
0000 0000
8-bit microcontroller with 8-bit ADC
Accumulator
P89LPC9151/9161/9171
Rev. 02 — 9 February 2010
ACC*
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR Bit functions and addresses
addr.
MSB
Reset value
LSB
Hex
Binary
00
0000 0000
BRGEN
00[2]
xxxx xx00
CO1
CMF1
00[1]
xx00 0000
CO2
CMF2
00[1]
xx00 0000
95H
00
0000 0000
Baud rate
generator 0
rate high
BFH
BRGCON
Baud rate
generator 0
control
BDH
-
-
-
-
-
-
SBRGS
CMP1
Comparator 1
control register
ACH
-
-
CE1
CP1
CN1
-
CMP2
Comparator 2
control register
ADH
-
-
CE2
CP2
CN2
OE2
DIVM
CPU clock
divide-by-M
control
DPTR
Data pointer
(2 bytes)
Data pointer
high
83H
00
0000 0000
DPL
Data pointer
low
82H
00
0000 0000
FMADRH
Program flash
address high
E7H
00
0000 0000
FMADRL
Program flash
address low
E6H
00
0000 0000
FMCON
Program flash
control (Read)
E4H
BUSY
-
-
-
HVA
HVE
SV
OI
70
0111 0000
Program flash
control (Write)
E4H
FMCMD.7
FMCMD.6
FMCMD.5
FMCMD.4
FMCMD.3
FMCMD.2
FMCMD.1
FMCMD.0
FMDATA
Program flash
data
E5H
00
0000 0000
I2ADR
I2C-bus slave
address
register
DBH
00
0000 0000
I2ADR.5
I2ADR.4
I2ADR.3
I2ADR.2
I2ADR.1
I2ADR.0
GC
8-bit microcontroller with 8-bit ADC
18 of 91
© NXP B.V. 2010. All rights reserved.
DPH
P89LPC9151/9161/9171
Rev. 02 — 9 February 2010
BRGR1[2]
I2ADR.6
NXP Semiconductors
P89LPC9151_61_71_2
Product data sheet
Table 6.
Special function registers - P89LPC9151
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR Bit functions and addresses
addr.
MSB
Bit address
Reset value
LSB
DF
DE
DD
DC
DB
DA
D9
D8
-
I2EN
STA
STO
SI
AA
-
CRSEL
Hex
Binary
00
x000 00x0
I2C-bus control
register
D8H
I2DAT
I2C-bus data
register
DAH
I2SCLH
Serial clock
generator/SCL
duty cycle
register high
DDH
00
0000 0000
I2SCLL
Serial clock
generator/SCL
duty cycle
register low
DCH
00
0000 0000
I2STAT
I2C-bus status
register
D9H
F8
1111 1000
00
0000 0000
00[1]
00x0 0000
IEN0*
Interrupt
enable 0
A8H
Bit address
IEN1*
Interrupt
enable 1
E8H
STA.3
STA.2
STA.1
STA.0
0
0
0
AF
AE
AD
AC
AB
AA
A9
A8
EA
EWDRT
EBO
ES/ESR
ET1
EX1
ET0
EX0
EF
EE
ED
EC
EB
EA
E9
E8
EAD
EST
-
-
-
EC
EKBI
EI2C
BF
BE
BD
BC
BB
BA
B9
B8
IP0*
Interrupt
priority 0
B8H
-
PWDRT
PBO
PS/PSR
PT1
PX1
PT0
PX0
00[1]
x000 0000
IP0H
Interrupt
priority 0 high
B7H
-
PWDRTH
PBOH
PSH/
PSRH
PT1H
PX1H
PT0H
PX0H
00[1]
x000 0000
FF
FE
FD
FC
FB
FA
F9
F8
Bit address
19 of 91
© NXP B.V. 2010. All rights reserved.
IP1*
Interrupt
priority 1
F8H
PAD
PST
-
-
-
PC
PKBI
PI2C
00[1]
00x0 0000
IP1H
Interrupt
priority 1 high
F7H
PADH
PSTH
-
-
-
PCH
PKBIH
PI2CH
00[1]
00x0 0000
KBCON
Keypad control
register
94H
-
-
-
-
-
-
PATN
_SEL
KBIF
00[1]
xxxx xx00
8-bit microcontroller with 8-bit ADC
Bit address
STA.4
P89LPC9151/9161/9171
Rev. 02 — 9 February 2010
I2CON*
Bit address
NXP Semiconductors
P89LPC9151_61_71_2
Product data sheet
Table 6.
Special function registers - P89LPC9151
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR Bit functions and addresses
addr.
MSB
Reset value
LSB
Hex
Binary
KBMASK
Keypad
interrupt mask
register
86H
00
0000 0000
KBPATN
Keypad pattern
register
93H
FF
1111 1111
Bit address
P0*
Port 0
80H
Bit address
P1*
Port 1
90H
87
86
85
84
83
82
81
80
-
-
CMPREF
/KB5
/CLKIN
CIN1A
/KB4
CIN1B
/KB3
CIN2A
/KB2
CIN2B
/KB1
CMP2
/KB0
97
96
95
94
93
92
91
90
-
-
RST
INT1
INT0/SDA
T0/SCL
RXD
TXD
B7
B6
B5
B4
B3
B2
B1
B0
[1]
[1]
Port 0 output
mode 1
84H
-
-
(P0M1.5)
(P0M1.4)
(P0M1.3)
(P0M1.2)
(P0M1.1)
(P0M1.0)
FF[1]
1111 1111
P0M2
Port 0 output
mode 2
85H
-
-
(P0M2.5)
(P0M2.4)
(P0M2.3)
(P0M2.2)
(P0M2.1)
(P0M2.0)
00[1]
0000 0000
P1M1
Port 1 output
mode 1
91H
-
-
-
(P1M1.4)
(P1M1.3)
(P1M1.2)
(P1M1.1)
(P1M1.0)
D3[1]
11x1 xx11
P1M2
Port 1 output
mode 2
92H
-
-
-
(P1M2.4)
(P1M2.3)
(P1M2.2)
(P1M2.1)
(P1M2.0)
00[1]
00x0 xx00
PCON
Power control
register
87H
SMOD1
SMOD0
-
BOI
GF1
GF0
PMOD1
PMOD0
00
0000 0000
PCONA
Power control
register A
B5H
RTCPD
-
VCPD
ADPD
I2PD
-
SPD
-
00[1]
0000 0000
D7
D6
D5
D4
D3
D2
D1
D0
PSW*
Program status
word
D0H
CY
AC
F0
RS1
RS0
OV
F1
P
00
0000 0000
PT0AD
Port 0 digital
input disable
F6H
-
-
PT0AD.5
PT0AD.4
PT0AD.3
PT0AD.2
PT0AD.1
-
00
xx00 000x
RSTSRC
Reset source
register
DFH
-
BOIF
BOF
POF
R_BK
R_WD
R_SF
R_EX
[3]
RTCCON
RTC control
D1H
RTCF
RTCS1
RTCS0
-
-
-
ERTC
RTCEN
Bit address
20 of 91
© NXP B.V. 2010. All rights reserved.
60[1][6]
011x xx00
8-bit microcontroller with 8-bit ADC
P0M1
P89LPC9151/9161/9171
Rev. 02 — 9 February 2010
Bit address
NXP Semiconductors
P89LPC9151_61_71_2
Product data sheet
Table 6.
Special function registers - P89LPC9151
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR Bit functions and addresses
addr.
MSB
Reset value
LSB
Hex
Binary
0000 0000
RTCH
RTC register
high
D2H
00[6]
RTCL
RTC register
low
D3H
00[6]
0000 0000
SADDR
Serial port
address
register
A9H
00
0000 0000
SADEN
Serial port
address enable
B9H
00
0000 0000
SBUF
Serial Port data
buffer register
99H
xx
xxxx xxxx
9F
9E
9D
9C
9B
9A
99
98
Serial port
control
98H
SM0/FE
SM1
SM2
REN
TB8
RB8
TI
RI
00
0000 0000
SSTAT
Serial port
extended
status register
BAH
DBMOD
INTLO
CIDIS
DBISEL
FE
BR
OE
STINT
00
0000 0000
SP
Stack pointer
81H
07
0000 0111
TAMOD
Timer 0 and 1
auxiliary mode
8FH
00
xxx0 xxx0
TCON*
Timer 0 and 1
control
88H
00
0000 0000
TH0
Timer 0 high
8CH
00
0000 0000
TH1
Timer 1 high
8DH
00
0000 0000
TL0
Timer 0 low
8AH
00
0000 0000
TL1
Timer 1 low
8BH
00
0000 0000
TMOD
Timer 0 and 1
mode
89H
T1GATE
T1C/T
T1M1
T1M0
T0GATE
T0C/T
T0M1
T0M0
00
0000 0000
TRIM
Internal
oscillator trim
register
96H
RCCLK
-
TRIM.5
TRIM.4
TRIM.3
TRIM.2
TRIM.1
TRIM.0
Bit address
-
-
-
-
-
-
-
T0M2
8F
8E
8D
8C
8B
8A
89
88
TF1
TR1
TF0
TR0
IE1
IT1
IE0
IT0
21 of 91
© NXP B.V. 2010. All rights reserved.
[5][6]
8-bit microcontroller with 8-bit ADC
SCON*
P89LPC9151/9161/9171
Rev. 02 — 9 February 2010
Bit address
NXP Semiconductors
P89LPC9151_61_71_2
Product data sheet
Table 6.
Special function registers - P89LPC9151
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR Bit functions and addresses
addr.
MSB
WDCON
Watchdog
control register
A7H
WDL
Watchdog load
C1H
WFEED1
Watchdog
feed 1
C2H
WFEED2
Watchdog
feed 2
C3H
[1]
PRE2
PRE1
PRE0
NXP Semiconductors
P89LPC9151_61_71_2
Product data sheet
Table 6.
Special function registers - P89LPC9151
* indicates SFRs that are bit addressable.
Reset value
-
-
WDRUN
WDTOF
LSB
Hex
WDCLK
[4][6]
FF
Binary
1111 1111
All ports are in input only (high-impedance) state after power-up.
BRGR1 and BRGR0 must only be written if BRGEN in BRGCON SFR is logic 0. If any are written while BRGEN = 1, the result is unpredictable.
[3]
The RSTSRC register reflects the cause of the P89LPC9151 reset except BOIF bit. Upon a power-up reset, all reset source flags are cleared except POF and BOF; the power-on
reset value is x011 0000.
[4]
After reset, the value is 1110 01x1, i.e., PRE2 to PRE0 are all logic 1, WDRUN = 1 and WDCLK = 1. WDTOF bit is logic 1 after watchdog reset and is logic 0 after power-on reset.
Other resets will not affect WDTOF.
[5]
On power-on reset and watchdog reset, the TRIM SFR is initialized with a factory preprogrammed value. Other resets will not cause initialization of the TRIM register.
[6]
The only reset sources that affect these SFRs are power-on reset and watchdog reset.
8-bit microcontroller with 8-bit ADC
22 of 91
© NXP B.V. 2010. All rights reserved.
P89LPC9151/9161/9171
Rev. 02 — 9 February 2010
[2]
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
NXP Semiconductors
P89LPC9151_61_71_2
Product data sheet
Table 7.
Extended special function registers - P89LPC9151[1]
Name
Description
SFR
addr.
Bit functions and addresses
Reset value
BODCFG
BOD
configuration
register
FFC8H
-
-
-
-
-
-
CLKCON
CLOCK Control
register
FFDEH
CLKOK
-
-
-
CLKDBL
FOSC2
RTCDATH
Real-time clock
data register
high
FFBFH
00
0000 0000
RTCDATL
Real-time clock FFBEH
data register low
00
0000 0000
MSB
LSB
BOICFG1 BOICFG0
FOSC1
FOSC0
Hex
Binary
[2]
[3]
Extended SFRs are physically located on-chip but logically located in external data memory address space (XDATA). The MOVX A,@DPTR and MOVX @DPTR,A instructions are
used to access these extended SFRs.
[2]
The BOICFG1/0 will be copied from UCFG1.5 and UCFG1.3 when power-on reset.
[3]
CLKCON register reset value comes from UCFG1 and UCFG2. The reset value of CLKCON.2 to CLKCON.0 come from UCFG1.2 to UCFG1.0 and reset value of CLKDBL bit
comes from UCFG2.7.
8-bit microcontroller with 8-bit ADC
23 of 91
© NXP B.V. 2010. All rights reserved.
P89LPC9151/9161/9171
Rev. 02 — 9 February 2010
[1]
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
NXP Semiconductors
P89LPC9151_61_71_2
Product data sheet
Table 8.
Special function registers - P89LPC9161
* indicates SFRs that are bit addressable.
Name
Description
SFR Bit functions and addresses
addr.
MSB
Bit address
E7
E6
Reset value
LSB
E5
E4
E3
E2
E1
Hex
Binary
00
0000 0000
E0
E0H
ADCON1
A/D control
register 1
97H
ENBI1
ENADCI1
TMM1
EDGE1
ADCI1
ENADC1
ADCS11
ADCS10
00
0000 0000
ADINS
A/D input
select
A3H
AIN13
AIN12
AIN11
AIN10
-
-
-
-
00
0000 0000
ADMODA
A/D mode
register A
C0H
BNDI1
BURST1
SCC1
SCAN1
-
-
-
-
00
0000 0000
ADMODB
A/D mode
register B
A1H
CLK2
CLK1
CLK0
INBND0
ENDAC1
-
BSA1
-
00
000x 0000
AD1BH
A/D_0
boundary high
register
C4H
FF
1111 1111
AD1BL
A/D_0
boundary low
register
BCH
00
0000 0000
AD1DAT0
A/D_0 data
register 0
D5H
00
0000 0000
AD1DAT1
A/D_0 data
register 1
D6H
00
0000 0000
AD1DAT2
A/D_0 data
register 2
D7H
00
0000 0000
AD1DAT3
A/D_0 data
register 3
F5H
00
0000 0000
AUXR1
Auxiliary
function
register
A2H
00
0000 00x0
24 of 91
© NXP B.V. 2010. All rights reserved.
Bit address
CLKLP
EBRR
-
ENT0
SRST
0
-
DPS
F7
F6
F5
F4
F3
F2
F1
F0
B*
B register
F0H
00
0000 0000
BRGR0[2]
Baud rate
generator 0
rate low
BEH
00
0000 0000
8-bit microcontroller with 8-bit ADC
Accumulator
P89LPC9151/9161/9171
Rev. 02 — 9 February 2010
ACC*
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR Bit functions and addresses
addr.
MSB
Reset value
LSB
Hex
Binary
00
0000 0000
BRGEN
00[2]
xxxx xx00
CO1
CMF1
00[1]
xx00 0000
CO2
CMF2
00[1]
xx00 0000
95H
00
0000 0000
Baud rate
generator 0
rate high
BFH
BRGCON
Baud rate
generator 0
control
BDH
-
-
-
-
-
-
SBRGS
CMP1
Comparator 1
control register
ACH
-
-
CE1
CP1
CN1
-
CMP2
Comparator 2
control register
ADH
-
-
CE2
CP2
CN2
-
DIVM
CPU clock
divide-by-M
control
DPTR
Data pointer
(2 bytes)
Data pointer
high
83H
00
0000 0000
DPL
Data pointer
low
82H
00
0000 0000
FMADRH
Program flash
address high
E7H
00
0000 0000
FMADRL
Program flash
address low
E6H
00
0000 0000
FMCON
Program flash
control (Read)
E4H
BUSY
-
-
-
HVA
HVE
SV
OI
70
0111 0000
Program flash
control (Write)
E4H
FMCMD.7
FMCMD.6
FMCMD.5
FMCMD.4
FMCMD.3
FMCMD.2
FMCMD.1
FMCMD.0
FMDATA
Program flash
data
E5H
00
0000 0000
I2ADR
I2C-bus slave
address
register
DBH
00
0000 0000
I2ADR.5
I2ADR.4
I2ADR.3
I2ADR.2
I2ADR.1
I2ADR.0
GC
8-bit microcontroller with 8-bit ADC
25 of 91
© NXP B.V. 2010. All rights reserved.
DPH
P89LPC9151/9161/9171
Rev. 02 — 9 February 2010
BRGR1[2]
I2ADR.6
NXP Semiconductors
P89LPC9151_61_71_2
Product data sheet
Table 8.
Special function registers - P89LPC9161
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR Bit functions and addresses
addr.
MSB
Bit address
Reset value
LSB
DF
DE
DD
DC
DB
DA
D9
D8
-
I2EN
STA
STO
SI
AA
-
CRSEL
Hex
Binary
00
x000 00x0
I2C-bus control
register
D8H
I2DAT
I2C-bus data
register
DAH
I2SCLH
Serial clock
generator/SCL
duty cycle
register high
DDH
00
0000 0000
I2SCLL
Serial clock
generator/SCL
duty cycle
register low
DCH
00
0000 0000
I2STAT
I2C-bus status
register
D9H
F8
1111 1000
00
0000 0000
00[1]
00x0 0000
IEN0*
Interrupt
enable 0
A8H
Bit address
IEN1*
Interrupt
enable 1
E8H
STA.3
STA.2
STA.1
STA.0
0
0
0
AF
AE
AD
AC
AB
AA
A9
A8
EA
EWDRT
EBO
ES/ESR
ET1
-
ET0
EX0
EF
EE
ED
EC
EB
EA
E9
E8
EAD
EST
-
-
ESPI
EC
EKBI
EI2C
BF
BE
BD
BC
BB
BA
B9
B8
IP0*
Interrupt
priority 0
B8H
-
PWDRT
PBO
PS/PSR
PT1
-
PT0
PX0
00[1]
x000 0000
IP0H
Interrupt
priority 0 high
B7H
-
PWDRTH
PBOH
PSH/
PSRH
PT1H
-
PT0H
PX0H
00[1]
x000 0000
FF
FE
FD
FC
FB
FA
F9
F8
Bit address
26 of 91
© NXP B.V. 2010. All rights reserved.
IP1*
Interrupt
priority 1
F8H
PAD
PST
-
-
PSPI
PC
PKBI
PI2C
00[1]
00x0 0000
IP1H
Interrupt
priority 1 high
F7H
PADH
PSTH
-
-
PSPIH
PCH
PKBIH
PI2CH
00[1]
00x0 0000
KBCON
Keypad control
register
94H
-
-
-
-
-
-
PATN
_SEL
KBIF
00[1]
xxxx xx00
8-bit microcontroller with 8-bit ADC
Bit address
STA.4
P89LPC9151/9161/9171
Rev. 02 — 9 February 2010
I2CON*
Bit address
NXP Semiconductors
P89LPC9151_61_71_2
Product data sheet
Table 8.
Special function registers - P89LPC9161
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR Bit functions and addresses
addr.
MSB
Reset value
LSB
Hex
Binary
KBMASK
Keypad
interrupt mask
register
86H
00
0000 0000
KBPATN
Keypad pattern
register
93H
FF
1111 1111
Bit address
P0*
Port 0
80H
Bit address
P1*
Port 1
90H
87
86
85
84
83
82
81
80
-
-
CMPREF
/KB5
/CLKIN
CIN1A
/KB4
CIN1B
/KB3
CIN2A
/KB2
CIN2B
/KB1
-
97
96
95
94
93
92
91
90
-
-
RST
-
INT0/SDA
T0/SCL
RXD
TXD
A7
A6
A5
A4
A3
A2
A1
A0
[1]
[1]
Port 2
A0H
-
-
SPICLK
SS
MISO
MOSI
-
-
[1]
P0M1
Port 0 output
mode 1
84H
-
-
(P0M1.5)
(P0M1.4)
(P0M1.3)
(P0M1.2)
(P0M1.1)
-
FF[1]
1111 1111
P0M2
Port 0 output
mode 2
85H
-
-
(P0M2.5)
(P0M2.4)
(P0M2.3)
(P0M2.2)
(P0M2.1)
-
00[1]
0000 0000
P1M1
Port 1 output
mode 1
91H
-
-
-
-
(P1M1.3)
(P1M1.2)
(P1M1.1)
(P1M1.0)
D3[1]
11x1 xx11
P1M2
Port 1 output
mode 2
92H
-
-
-
-
(P1M2.3)
(P1M2.2)
(P1M2.1)
(P1M2.0)
00[1]
00x0 xx00
P2M1
Port 2 output
mode 1
A4H
-
-
(P2M1.5)
(P2M1.4)
(P2M1.3)
(P2M1.2)
-
-
03[1]
xxxx xx11
P2M2
Port 2 output
mode 2
A5H
-
-
(P2M2.5)
(P2M2.4)
(P2M2.3)
(P2M2.2)
-
-
00[1]
xxxx xx00
PCON
Power control
register
87H
SMOD1
SMOD0
-
BOI
GF1
GF0
PMOD1
PMOD0
00
0000 0000
PCONA
Power control
register A
B5H
RTCPD
-
VCPD
ADPD
I2PD
SPPD
SPD
-
00[1]
0000 0000
D7
D6
D5
D4
D3
D2
D1
D0
CY
AC
F0
RS1
RS0
OV
F1
P
00
0000 0000
Bit address
PSW*
Program status
word
D0H
8-bit microcontroller with 8-bit ADC
27 of 91
© NXP B.V. 2010. All rights reserved.
P2*
P89LPC9151/9161/9171
Rev. 02 — 9 February 2010
Bit address
NXP Semiconductors
P89LPC9151_61_71_2
Product data sheet
Table 8.
Special function registers - P89LPC9161
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR Bit functions and addresses
addr.
MSB
Reset value
LSB
Hex
Binary
xx00 000x
PT0AD
Port 0 digital
input disable
F6H
-
-
PT0AD.5
PT0AD.4
PT0AD.3
PT0AD.2
PT0AD.1
-
00
RSTSRC
Reset source
register
DFH
-
BOIF
BOF
POF
R_BK
R_WD
R_SF
R_EX
[3]
RTCCON
RTC control
D1H
RTCF
RTCS1
RTCS0
-
-
-
ERTC
RTCEN
RTCH
RTC register
high
RTCL
00[6]
0000 0000
RTC register
low
D3H
00[6]
0000 0000
SADDR
Serial port
address
register
A9H
00
0000 0000
SADEN
Serial port
address enable
B9H
00
0000 0000
SBUF
Serial Port data
buffer register
99H
xx
xxxx xxxx
9F
9E
9D
9C
9B
9A
99
98
SCON*
Serial port
control
98H
SM0/FE
SM1
SM2
REN
TB8
RB8
TI
RI
00
0000 0000
SSTAT
Serial port
extended
status register
BAH
DBMOD
INTLO
CIDIS
DBISEL
FE
BR
OE
STINT
00
0000 0000
SP
Stack pointer
81H
07
0000 0111
SPCTL
SPI control
register
E2H
SSIG
SPEN
DORD
MSTR
CPOL
CPHA
SPR1
SPR0
04
0000 0100
SPSTAT
SPI status
register
E1H
SPIF
WCOL
-
-
-
-
-
-
00
00xx xxxx
SPDAT
SPI data
register
E3H
00
0000 0000
TAMOD
Timer 0 and 1
auxiliary mode
8FH
00
xxx0 xxx0
28 of 91
© NXP B.V. 2010. All rights reserved.
-
-
-
-
-
-
-
T0M2
8-bit microcontroller with 8-bit ADC
011x xx00
D2H
P89LPC9151/9161/9171
Rev. 02 — 9 February 2010
60[1][6]
Bit address
NXP Semiconductors
P89LPC9151_61_71_2
Product data sheet
Table 8.
Special function registers - P89LPC9161
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR Bit functions and addresses
addr.
MSB
Bit address
Reset value
LSB
8F
8E
8D
8C
8B
8A
89
88
TF1
TR1
TF0
TR0
-
-
IE0
IT0
Hex
Binary
00
0000 0000
Timer 0 and 1
control
88H
TH0
Timer 0 high
8CH
00
0000 0000
TH1
Timer 1 high
8DH
00
0000 0000
TL0
Timer 0 low
8AH
00
0000 0000
TL1
Timer 1 low
8BH
00
0000 0000
TMOD
Timer 0 and 1
mode
89H
T1GATE
T1C/T
T1M1
T1M0
T0GATE
T0C/T
T0M1
T0M0
00
0000 0000
TRIM
Internal
oscillator trim
register
96H
RCCLK
-
TRIM.5
TRIM.4
TRIM.3
TRIM.2
TRIM.1
TRIM.0
[5][6]
WDCON
Watchdog
control register
A7H
PRE2
PRE1
PRE0
-
-
WDRUN
WDTOF
WDCLK
[4][6]
WDL
Watchdog load
C1H
WFEED1
Watchdog
feed 1
C2H
WFEED2
Watchdog
feed 2
C3H
FF
1111 1111
All ports are in input only (high-impedance) state after power-up.
BRGR1 and BRGR0 must only be written if BRGEN in BRGCON SFR is logic 0. If any are written while BRGEN = 1, the result is unpredictable.
[3]
The RSTSRC register reflects the cause of the P89LPC9161 reset except BOIF bit. Upon a power-up reset, all reset source flags are cleared except POF and BOF; the power-on
reset value is x011 0000.
[4]
After reset, the value is 1110 01x1, i.e., PRE2 to PRE0 are all logic 1, WDRUN = 1 and WDCLK = 1. WDTOF bit is logic 1 after watchdog reset and is logic 0 after power-on reset.
Other resets will not affect WDTOF.
[5]
On power-on reset and watchdog reset, the TRIM SFR is initialized with a factory preprogrammed value. Other resets will not cause initialization of the TRIM register.
[6]
The only reset sources that affect these SFRs are power-on reset and watchdog reset.
8-bit microcontroller with 8-bit ADC
29 of 91
© NXP B.V. 2010. All rights reserved.
[2]
P89LPC9151/9161/9171
Rev. 02 — 9 February 2010
TCON*
[1]
NXP Semiconductors
P89LPC9151_61_71_2
Product data sheet
Table 8.
Special function registers - P89LPC9161
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
NXP Semiconductors
P89LPC9151_61_71_2
Product data sheet
Table 9.
Extended special function registers - P89LPC9161[1]
Name
Description
SFR
addr.
Bit functions and addresses
Reset value
BODCFG
BOD
configuration
register
FFC8H
-
-
-
-
-
-
CLKCON
CLOCK Control
register
FFDEH
CLKOK
-
-
-
CLKDBL
FOSC2
RTCDATH
Real-time clock
data register
high
FFBFH
00
0000 0000
RTCDATL
Real-time clock FFBEH
data register low
00
0000 0000
MSB
LSB
BOICFG1 BOICFG0
FOSC1
FOSC0
Hex
Binary
[2]
[3]
Extended SFRs are physically located on-chip but logically located in external data memory address space (XDATA). The MOVX A,@DPTR and MOVX @DPTR,A instructions are
used to access these extended SFRs.
[2]
The BOICFG1/0 will be copied from UCFG1.5 and UCFG1.3 when power-on reset.
[3]
CLKCON register reset value comes from UCFG1 and UCFG2. The reset value of CLKCON.2 to CLKCON.0 come from UCFG1.2 to UCFG1.0 and reset value of CLKDBL bit
comes from UCFG2.7.
8-bit microcontroller with 8-bit ADC
30 of 91
© NXP B.V. 2010. All rights reserved.
P89LPC9151/9161/9171
Rev. 02 — 9 February 2010
[1]
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
NXP Semiconductors
P89LPC9151_61_71_2
Product data sheet
Table 10. Special function registers - P89LPC9171
* indicates SFRs that are bit addressable.
Name
Description
SFR Bit functions and addresses
addr.
MSB
Bit address
E7
E6
E5
Reset value
LSB
E4
E3
E2
E1
Hex
Binary
00
0000 0000
E0
E0H
ADCON1
A/D control
register 1
97H
ENBI1
ENADCI1
TMM1
EDGE1
ADCI1
ENADC1
ADCS11
ADCS10
00
0000 0000
ADINS
A/D input
select
A3H
AIN13
AIN12
AIN11
AIN10
-
-
-
-
00
0000 0000
ADMODA
A/D mode
register A
C0H
BNDI1
BURST1
SCC1
SCAN1
-
-
-
-
00
0000 0000
ADMODB
A/D mode
register B
A1H
CLK2
CLK1
CLK0
INBND0
ENDAC1
-
BSA1
-
00
000x 0000
AD1BH
A/D_0
boundary high
register
C4H
FF
1111 1111
AD1BL
A/D_0
boundary low
register
BCH
00
0000 0000
AD1DAT0
A/D_0 data
register 0
D5H
00
0000 0000
AD1DAT1
A/D_0 data
register 1
D6H
00
0000 0000
AD1DAT2
A/D_0 data
register 2
D7H
00
0000 0000
AD1DAT3
A/D_0 data
register 3
F5H
00
0000 0000
AUXR1
Auxiliary
function
register
A2H
00
0000 00x0
31 of 91
© NXP B.V. 2010. All rights reserved.
Bit address
CLKLP
EBRR
ENT1
ENT0
SRST
0
-
DPS
F7
F6
F5
F4
F3
F2
F1
F0
B*
B register
F0H
00
0000 0000
BRGR0[2]
Baud rate
generator 0
rate low
BEH
00
0000 0000
8-bit microcontroller with 8-bit ADC
Accumulator
P89LPC9151/9161/9171
Rev. 02 — 9 February 2010
ACC*
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR Bit functions and addresses
addr.
MSB
Reset value
LSB
Hex
Binary
00
0000 0000
BRGEN
00[2]
xxxx xx00
CO1
CMF1
00[1]
xx00 0000
CO2
CMF2
00[1]
xx00 0000
95H
00
0000 0000
Baud rate
generator 0
rate high
BFH
BRGCON
Baud rate
generator 0
control
BDH
-
-
-
-
-
-
SBRGS
CMP1
Comparator 1
control register
ACH
-
-
CE1
CP1
CN1
-
CMP2
Comparator 2
control register
ADH
-
-
CE2
CP2
CN2
OE2
DIVM
CPU clock
divide-by-M
control
DPTR
Data pointer
(2 bytes)
Data pointer
high
83H
00
0000 0000
DPL
Data pointer
low
82H
00
0000 0000
FMADRH
Program flash
address high
E7H
00
0000 0000
FMADRL
Program flash
address low
E6H
00
0000 0000
FMCON
Program flash
control (Read)
E4H
BUSY
-
-
-
HVA
HVE
SV
OI
70
0111 0000
Program flash
control (Write)
E4H
FMCMD.7
FMCMD.6
FMCMD.5
FMCMD.4
FMCMD.3
FMCMD.2
FMCMD.1
FMCMD.0
FMDATA
Program flash
data
E5H
00
0000 0000
I2ADR
I2C-bus slave
address
register
DBH
00
0000 0000
I2ADR.5
I2ADR.4
I2ADR.3
I2ADR.2
I2ADR.1
I2ADR.0
GC
8-bit microcontroller with 8-bit ADC
32 of 91
© NXP B.V. 2010. All rights reserved.
DPH
P89LPC9151/9161/9171
Rev. 02 — 9 February 2010
BRGR1[2]
I2ADR.6
NXP Semiconductors
P89LPC9151_61_71_2
Product data sheet
Table 10. Special function registers - P89LPC9171
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR Bit functions and addresses
addr.
MSB
Bit address
Reset value
LSB
DF
DE
DD
DC
DB
DA
D9
D8
-
I2EN
STA
STO
SI
AA
-
CRSEL
Hex
Binary
00
x000 00x0
I2C-bus control
register
D8H
I2DAT
I2C-bus data
register
DAH
I2SCLH
Serial clock
generator/SCL
duty cycle
register high
DDH
00
0000 0000
I2SCLL
Serial clock
generator/SCL
duty cycle
register low
DCH
00
0000 0000
I2STAT
I2C-bus status
register
D9H
F8
1111 1000
00
0000 0000
00[1]
00x0 0000
IEN0*
Interrupt
enable 0
A8H
Bit address
IEN1*
Interrupt
enable 1
E8H
STA.3
STA.2
STA.1
STA.0
0
0
0
AF
AE
AD
AC
AB
AA
A9
A8
EA
EWDRT
EBO
ES/ESR
ET1
EX1
ET0
EX0
EF
EE
ED
EC
EB
EA
E9
E8
EAD
EST
-
-
-
EC
EKBI
EI2C
BF
BE
BD
BC
BB
BA
B9
B8
IP0*
Interrupt
priority 0
B8H
-
PWDRT
PBO
PS/PSR
PT1
PX1
PT0
PX0
00[1]
x000 0000
IP0H
Interrupt
priority 0 high
B7H
-
PWDRTH
PBOH
PSH/
PSRH
PT1H
PX1H
PT0H
PX0H
00[1]
x000 0000
FF
FE
FD
FC
FB
FA
F9
F8
Bit address
33 of 91
© NXP B.V. 2010. All rights reserved.
IP1*
Interrupt
priority 1
F8H
PAD
PST
-
-
-
PC
PKBI
PI2C
00[1]
00x0 0000
IP1H
Interrupt
priority 1 high
F7H
PADH
PSTH
-
-
-
PCH
PKBIH
PI2CH
00[1]
00x0 0000
KBCON
Keypad control
register
94H
-
-
-
-
-
-
PATN
_SEL
KBIF
00[1]
xxxx xx00
8-bit microcontroller with 8-bit ADC
Bit address
STA.4
P89LPC9151/9161/9171
Rev. 02 — 9 February 2010
I2CON*
Bit address
NXP Semiconductors
P89LPC9151_61_71_2
Product data sheet
Table 10. Special function registers - P89LPC9171
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR Bit functions and addresses
addr.
MSB
Reset value
LSB
Hex
Binary
KBMASK
Keypad
interrupt mask
register
86H
00
0000 0000
KBPATN
Keypad pattern
register
93H
FF
1111 1111
Bit address
P0*
Port 0
80H
Bit address
P1*
Port 1
90H
87
86
85
84
83
82
81
80
T1/KB7
/CLKOUT
-
CMPREF
/KB5
/CLKIN
CIN1A
/KB4
CIN1B
/KB3
CIN2A
/KB2
CIN2B
/KB1
CMP2
/KBI0
97
96
95
94
93
92
91
90
-
-
RST
INT1
INT0/SDA
T0/SCL
RXD
TXD
A7
A6
A5
A4
A3
A2
A1
A0
00[1]
[1]
[1]
Port 2
A0H
-
-
-
-
-
-
-
-
P0M1
Port 0 output
mode 1
84H
(P0M1.7)
-
(P0M1.5)
(P0M1.4)
(P0M1.3)
(P0M1.2)
(P0M1.1)
(P0M1.0)
FF[1]
1111 1111
P0M2
Port 0 output
mode 2
85H
(P0M2.7)
-
(P0M2.5)
(P0M2.4)
(P0M2.3)
(P0M2.2)
(P0M2.1)
(P0M2.0)
00[1]
0000 0000
P1M1
Port 1 output
mode 1
91H
-
-
-
-
(P1M1.3)
(P1M1.2)
(P1M1.1)
(P1M1.0)
D3[1]
11x1 xx11
P1M2
Port 1 output
mode 2
92H
-
-
-
-
(P1M2.3)
(P1M2.2)
(P1M2.1)
(P1M2.0)
00[1]
00x0 xx00
P2M1
Port 2 output
mode 1
A4H
-
-
-
-
-
(P2M1.2)
-
-
FF[1]
1111 1111
P2M2
Port 2 output
mode 2
A5H
-
-
-
-
-
(P2M2.2)
-
-
00[1]
0000 0000
PCON
Power control
register
87H
SMOD1
SMOD0
-
BOI
GF1
GF0
PMOD1
PMOD0
00
0000 0000
PCONA
Power control
register A
B5H
RTCPD
-
VCPD
ADPD
I2PD
-
SPD
-
00[1]
0000 0000
D7
D6
D5
D4
D3
D2
D1
D0
CY
AC
F0
RS1
RS0
OV
F1
P
00
0000 0000
Bit address
PSW*
Program status
word
D0H
8-bit microcontroller with 8-bit ADC
34 of 91
© NXP B.V. 2010. All rights reserved.
P2*
P89LPC9151/9161/9171
Rev. 02 — 9 February 2010
Bit address
NXP Semiconductors
P89LPC9151_61_71_2
Product data sheet
Table 10. Special function registers - P89LPC9171
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR Bit functions and addresses
addr.
MSB
Reset value
LSB
Hex
Binary
xx00 000x
PT0AD
Port 0 digital
input disable
F6H
-
-
PT0AD.5
PT0AD.4
PT0AD.3
PT0AD.2
PT0AD.1
-
00
RSTSRC
Reset source
register
DFH
-
BOIF
BOF
POF
R_BK
R_WD
R_SF
R_EX
[3]
RTCCON
RTC control
D1H
RTCF
RTCS1
RTCS0
-
-
-
ERTC
RTCEN
RTCH
RTC register
high
RTCL
00[6]
0000 0000
RTC register
low
D3H
00[6]
0000 0000
SADDR
Serial port
address
register
A9H
00
0000 0000
SADEN
Serial port
address enable
B9H
00
0000 0000
SBUF
Serial Port data
buffer register
99H
xx
xxxx xxxx
9F
9E
9D
9C
9B
9A
99
98
SCON*
Serial port
control
98H
SM0/FE
SM1
SM2
REN
TB8
RB8
TI
RI
00
0000 0000
SSTAT
Serial port
extended
status register
BAH
DBMOD
INTLO
CIDIS
DBISEL
FE
BR
OE
STINT
00
0000 0000
SP
Stack pointer
81H
07
0000 0111
TAMOD
Timer 0 and 1
auxiliary mode
8FH
00
xxx0 xxx0
00
0000 0000
Bit address
-
-
-
T1M2
-
-
-
T0M2
8F
8E
8D
8C
8B
8A
89
88
TF1
TR1
TF0
TR0
IE1
IT1
IE0
IT0
35 of 91
© NXP B.V. 2010. All rights reserved.
TCON*
Timer 0 and 1
control
88H
TH0
Timer 0 high
8CH
00
0000 0000
TH1
Timer 1 high
8DH
00
0000 0000
TL0
Timer 0 low
8AH
00
0000 0000
TL1
Timer 1 low
8BH
00
0000 0000
8-bit microcontroller with 8-bit ADC
011x xx00
D2H
P89LPC9151/9161/9171
Rev. 02 — 9 February 2010
60[1][6]
Bit address
NXP Semiconductors
P89LPC9151_61_71_2
Product data sheet
Table 10. Special function registers - P89LPC9171
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR Bit functions and addresses
addr.
MSB
NXP Semiconductors
P89LPC9151_61_71_2
Product data sheet
Table 10. Special function registers - P89LPC9171
* indicates SFRs that are bit addressable.
Reset value
LSB
Hex
Binary
00
0000 0000
Timer 0 and 1
mode
89H
T1GATE
T1C/T
T1M1
T1M0
T0GATE
T0C/T
T0M1
T0M0
TRIM
Internal
oscillator trim
register
96H
RCCLK
ENCLK
TRIM.5
TRIM.4
TRIM.3
TRIM.2
TRIM.1
TRIM.0
[5][6]
WDCON
Watchdog
control register
A7H
PRE2
PRE1
PRE0
-
-
WDRUN
WDTOF
WDCLK
[4][6]
WDL
Watchdog load
C1H
WFEED1
Watchdog
feed 1
C2H
WFEED2
Watchdog
feed 2
C3H
FF
1111 1111
[1]
All ports are in input only (high-impedance) state after power-up.
[2]
BRGR1 and BRGR0 must only be written if BRGEN in BRGCON SFR is logic 0. If any are written while BRGEN = 1, the result is unpredictable.
[3]
The RSTSRC register reflects the cause of the P89LPC9171 reset except BOIF bit. Upon a power-up reset, all reset source flags are cleared except POF and BOF; the power-on
reset value is x011 0000.
[4]
After reset, the value is 1110 01x1, i.e., PRE2 to PRE0 are all logic 1, WDRUN = 1 and WDCLK = 1. WDTOF bit is logic 1 after watchdog reset and is logic 0 after power-on reset.
Other resets will not affect WDTOF.
[5]
On power-on reset and watchdog reset, the TRIM SFR is initialized with a factory preprogrammed value. Other resets will not cause initialization of the TRIM register.
[6]
The only reset sources that affect these SFRs are power-on reset and watchdog reset.
8-bit microcontroller with 8-bit ADC
36 of 91
© NXP B.V. 2010. All rights reserved.
P89LPC9151/9161/9171
Rev. 02 — 9 February 2010
TMOD
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
NXP Semiconductors
P89LPC9151_61_71_2
Product data sheet
Table 11.
Extended special function registers - P89LPC9171[1]
Name
Description
SFR
addr.
Bit functions and addresses
Reset value
BODCFG
BOD
configuration
register
FFC8H
-
-
-
-
-
-
CLKCON
CLOCK Control
register
FFDEH
CLKOK
-
-
-
CLKDBL
FOSC2
RTCDATH
Real-time clock
data register
high
FFBFH
00
0000 0000
RTCDATL
Real-time clock FFBEH
data register low
00
0000 0000
MSB
LSB
BOICFG1 BOICFG0
FOSC1
FOSC0
Hex
Binary
[2]
[3]
Extended SFRs are physically located on-chip but logically located in external data memory address space (XDATA). The MOVX A,@DPTR and MOVX @DPTR,A instructions are
used to access these extended SFRs.
[2]
The BOICFG1/0 will be copied from UCFG1.5 and UCFG1.3 when power-on reset.
[3]
CLKCON register reset value comes from UCFG1 and UCFG2. The reset value of CLKCON.2 to CLKCON.0 come from UCFG1.2 to UCFG1.0 and reset value of CLKDBL bit
comes from UCFG2.7.
8-bit microcontroller with 8-bit ADC
37 of 91
© NXP B.V. 2010. All rights reserved.
P89LPC9151/9161/9171
Rev. 02 — 9 February 2010
[1]
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
7.2 Enhanced CPU
The P89LPC9151/9161/9171 uses an enhanced 80C51 CPU which runs at six times the
speed of standard 80C51 devices. A machine cycle consists of two CPU clock cycles, and
most instructions execute in one or two machine cycles.
7.3 Clocks
7.3.1 Clock definitions
The P89LPC9151/9161/9171 device has several internal clocks as defined below:
OSCCLK — Input to the DIVM clock divider. OSCCLK is selected from one of four clock
sources (see Figure 10) and can also be optionally divided to a slower frequency (see
Section 7.10 “CCLK modification: DIVM register”).
Remark: fosc is defined as the OSCCLK frequency.
CCLK — CPU clock; output of the clock divider. There are two CCLK cycles per machine
cycle, and most instructions are executed in one to two machine cycles (two or four CCLK
cycles).
RCCLK — The internal 7.373 MHz RC oscillator output. The clock doubler option, when
enabled, provides an output frequency of 14.746 MHz.
PCLK — Clock for the various peripheral devices and is CCLK⁄2.
7.3.2 CPU clock (OSCCLK)
The P89LPC9151/9161/9171 provides several user-selectable oscillator options in
generating the CPU clock. This allows optimization for a range of needs from high
precision to lowest possible cost. These options are configured when the flash is
programmed and include an on-chip watchdog oscillator, an on-chip RC oscillator, or an
external clock source.
7.4 Clock output (P89LPC9171)
The P89LPC9171 supports a user-selectable clock output function on the P0.7/CLKOUT
pin. This allows external devices to synchronize to the P89LPC9171. This output is
enabled by the ENCLK bit in the TRIM register.
The frequency of this clock output is 1⁄2 that of the CCLK. If the clock output is not needed
in Idle mode, it may be turned off prior to entering Idle, saving additional power.
7.5 On-chip RC oscillator option
The P89LPC9151/9161/9171 has a 6-bit TRIM register that can be used to tune the
frequency of the RC oscillator. During reset, the TRIM value is initialized to a factory
preprogrammed value to adjust the oscillator frequency to 7.373 MHz ± 1 % at room
temperature. End-user applications can write to the TRIM register to adjust the on-chip
RC oscillator to other frequencies. When the clock doubler option is enabled (UCFG2.7 =
1), the output frequency is 14.746 MHz. If CCLK is 8 MHz or slower, the CLKLP SFR bit
(AUXR1.7) can be set to logic 1 to reduce power consumption. On reset, CLKLP is logic 0
allowing highest performance access. This bit can then be set in software if CCLK is
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
38 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
running at 8 MHz or slower. When clock doubler option is enabled, BOE1 bit (UCFG1.5)
and BOE0 bit (UCFG1.3) are required to hold the device in reset at power-up until VDD
has reached its specified level.
7.6 Watchdog oscillator option
The watchdog has a separate oscillator which has a frequency of 400 kHz, calibrated to
±5 % at room temperature. This oscillator can be used to save power when a high clock
frequency is not needed.
7.7 External clock input option
In this configuration, the processor clock is derived from an external source driving the
P0.5/CLKIN pin. The rate may be from 0 Hz up to 18 MHz. When the frequency above
12 MHz, BOE1 bit (UCFG1.5) and BOE0 bit (UCFG1.3) are required to hold the device in
reset at power-up until VDD has reached its specified level.
Remark: When using P0.5 as a clock input option, please make sure that P0.5 is
configured as input only mode.
7.8 Clock sources switch on the fly
P89LPC9151/9161/9171 can implement clock source switch in any sources of watchdog
oscillator, 7 MHz/14 MHz IRC oscillator, or external clock input during code is running.
CLKOK bit in CLKCON register is used to indicate the clock switch status. CLKOK is
cleared when starting clock source switch and set when completed. Notice that when
CLKOK is ‘0’, writing to CLKCON register is not allowed.
RTCS1:0
XCLK
RTC
RCCLK
CLKOUT
OSCCLK
CLKIN
CCLK
DIVM
RC
OSCILLATOR
CPU
RCCLK
ADC1/DAC1
(7.3728 MHz/14.7456 MHz ± 1 %)
÷2
PCLK
WDT
WATCHDOG
OSCILLATOR
(400 kHz ± 5 %)
PCLK
TIMER 0 AND
TIMER 1
I2C-BUS
UART
SPI
(P89LPC9161)
002aae574
Fig 10. Block diagram of oscillator control
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
39 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
7.9 CCLK wake-up delay
The P89LPC9151/9161/9171 has an internal wake-up timer that delays the clock until it
stabilizes depending on the clock source used. If the clock source is any of the three
crystal selections (low, medium and high frequencies) the delay is 1024 OSCCLK cycles
plus 60 μs to 100 μs. If the clock source is the internal RC oscillator, the delay is 200 μs to
300 μs. If the clock source is watchdog oscillator or external clock, the delay is
32 OSCCLK cycles.
7.10 CCLK modification: DIVM register
The OSCCLK frequency can be divided down up to 510 times by configuring a dividing
register, DIVM, to generate CCLK. This feature makes it possible to temporarily run the
CPU at a lower rate, reducing power consumption. By dividing the clock, the CPU can
retain the ability to respond to events that would not exit Idle mode by executing its normal
program at a lower rate. This can also allow bypassing the oscillator start-up time in cases
where Power-down mode would otherwise be used. The value of DIVM may be changed
by the program at any time without interrupting code execution.
7.11 Low power select
The P89LPC9151/9161/9171 is designed to run at 18 MHz (CCLK) maximum. However, if
CCLK is 8 MHz or slower, the CLKLP SFR bit (AUXR1.7) can be set to logic 1 to lower the
power consumption further. On any reset, CLKLP is logic 0 allowing highest performance
access. This bit can then be set in software if CCLK is running at 8 MHz or slower.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
40 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
7.12 Memory organization
The various P89LPC9151/9161/9171 memory spaces are as follows:
• DATA
128 bytes of internal data memory space (00H:7FH) accessed via direct or indirect
addressing, using instructions other than MOVX and MOVC. All or part of the Stack
may be in this area.
• IDATA
Indirect Data. 256 bytes of internal data memory space (00H:FFH) accessed via
indirect addressing using instructions other than MOVX and MOVC. All or part of the
Stack may be in this area. This area includes the DATA area and the 128 bytes
immediately above it.
• SFR
Special Function Registers. Selected CPU registers and peripheral control and status
registers, accessible only via direct addressing.
• XDATA
‘External’ Data or Auxiliary RAM. Duplicates the classic 80C51 64 kB memory space
addressed via the MOVX instruction using the DPTR, R0, or R1. All or part of this
space could be implemented on-chip. Extended SFRs located in XDATA.
• CODE
64 kB of Code memory space, accessed as part of program execution and via the
MOVC instruction. The P89LPC9151/9161/9171 has 2 kB on-chip Code memory.
7.13 Data RAM arrangement
The 256 bytes of on-chip RAM are organized as shown in Table 12.
Table 12.
On-chip data memory usages
Type
Data RAM
Size (bytes)
DATA
Memory that can be addressed directly and indirectly
128
IDATA
Memory that can be addressed indirectly
256
7.14 Interrupts
The P89LPC9151/9161/9171 uses a four priority level interrupt structure. This allows
great flexibility in controlling the handling of the many interrupt sources.
The P89LPC9151/9171 supports 13 interrupt sources: external interrupts 0 and 1, timers
0 and 1, serial port TX, serial port RX, combined serial port RX/TX, brownout detect,
watchdog/RTC, I2C-bus, keyboard, comparators 1 and 2, A/D completion.
The P89LPC9161 supports 13 interrupt sources: external interrupts 0, timers 0 and 1,
serial port TX, serial port RX, combined serial port RX/TX, brownout detect,
watchdog/RTC, I2C-bus, keyboard, comparators 1 and 2, SPI, ADC completion.
Each interrupt source can be individually enabled or disabled by setting or clearing a bit in
the interrupt enable registers IEN0 or IEN1. The IEN0 register also contains a global
disable bit, EA, which disables all interrupts.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
41 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
Each interrupt source can be individually programmed to one of four priority levels by
setting or clearing bits in the interrupt priority registers IP0, IP0H, IP1 and IP1H. An
interrupt service routine in progress can be interrupted by a higher priority interrupt, but
not by another interrupt of the same or lower priority. The highest priority interrupt service
cannot be interrupted by any other interrupt source. If two requests of different priority
levels are pending at the start of an instruction, the request of higher priority level is
serviced.
If requests of the same priority level are pending at the start of an instruction, an internal
polling sequence determines which request is serviced. This is called the arbitration
ranking. Note that the arbitration ranking is only used to resolve pending requests of the
same priority level.
7.14.1 External interrupt inputs
The P89LPC9151 and P89LPC9171 have two external interrupt inputs as well as the
Keypad Interrupt function. The P89LPC9161 has one external interrupt input as well as
the Keypad Interrupt function These external interrupt inputs are identical to those present
on the standard 80C51 microcontrollers.
These external interrupts can be programmed to be level-triggered or edge-triggered by
setting or clearing bit IT1 or IT0 in Register TCON.
In edge-triggered mode, if successive samples of the INTn pin show a HIGH in one cycle
and a LOW in the next cycle, the interrupt request flag IEn in TCON is set, causing an
interrupt request.
If an external interrupt is enabled when the P89LPC9151/9161/9171 is put into
Power-down or Idle mode, the interrupt will cause the processor to wake-up and resume
operation. Refer to Section 7.17 “Power reduction modes” for details.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
42 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
IE0
EX0
IE1
EX1
BOIF
EBO
RTCF
ERTC
(RTCCON.1)
wake-up
(if in power-down)
KBIF
EKBI
WDOVF
EWDRT
CMF2
CMF1
EC
EA (IE0.7)
TF0
ET0
TF1
ET1
TI and RI/RI
ES/ESR
interrupt
to CPU
TI
EST
SI
EI2C
SPIF
ENADCI1
ADCI1
ENBI1
BNDI1
(P89LPC9161) ESPI
EAD
002aae575
Fig 11. Interrupt sources, interrupt enables, and power-down wake-up sources
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
43 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
7.15 I/O ports
The P89LPC9151 has two I/O ports: Port 0 and Port 1. Ports 0 and 1 are both 6-bit ports.
The P89LPC9161/9171 has three I/O ports: Port 0, Port 1 and Port 2. Ports 0 is 5-bit ports
in the P89LPC9161 and 7-bit ports in the P89LPC9171, Port 1 is 5-bit ports in the
P89LPC9161 and 6-bit ports in the P89LPC9171, Port 2 is 4-bit ports in the P89LPC9161
and 1-bit port in the P89LPC9171. The exact number of I/O pins available depends upon
the clock and reset options chosen, as shown in Table 13 and Table 14
Table 13.
Number of I/O pins available (P89LPC9151)
Clock source
Reset option
Number of I/O
pins (14-pin
package)
RC oscillator or watchdog
oscillator
No external reset (except during
power-up)
12
External RST pin supported
11
No external reset (except during
power-up)
11
External RST pin supported[1]
10
External clock input
[1]
Required for operation above 12 MHz.
Table 14.
Number of I/O pins available (P89LPC9161 and P89LPC9171)
Clock source
Reset option
Number of I/O
pins (16-pin
package)
RC oscillator or watchdog
oscillator
No external reset (except during
power-up)
14
External RST pin supported
13
No external reset (except during
power-up)
13
External RST pin supported[1]
12
External clock input
[1]
Required for operation above 12 MHz.
7.15.1 Port configurations
All but three I/O port pins on the P89LPC9151/9161/9171 may be configured by software
to one of four types on a bit-by-bit basis. These are: quasi-bidirectional (standard 80C51
port outputs), push-pull, open drain, and input-only. Two configuration registers for each
port select the output type for each port pin.
1. P1.5 (RST) can only be an input and cannot be configured.
2. P1.2 (SCL/T0) and P1.3 (SDA/INT0) may only be configured to be either input-only or
open-drain.
7.15.1.1
Quasi-bidirectional output configuration
Quasi-bidirectional output type can be used as both an input and output without the need
to reconfigure the port. This is possible because when the port outputs a logic HIGH, it is
weakly driven, allowing an external device to pull the pin LOW. When the pin is driven
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
44 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
LOW, it is driven strongly and able to sink a fairly large current. These features are
somewhat similar to an open-drain output except that there are three pull-up transistors in
the quasi-bidirectional output that serve different purposes.
The P89LPC9151/9161/9171 is a 3 V device, but the pins are 5 V tolerant. In
quasi-bidirectional mode, if a user applies 5 V on the pin, there will be a current flowing
from the pin to VDD, causing extra power consumption. Therefore, applying 5 V in
quasi-bidirectional mode is discouraged.
A quasi-bidirectional port pin has a Schmitt trigger input that also has a glitch suppression
circuit.
7.15.1.2
Open-drain output configuration
The open-drain output configuration turns off all pull-ups and only drives the pull-down
transistor of the port driver when the port latch contains a logic 0. To be used as a logic
output, a port configured in this manner must have an external pull-up, typically a resistor
tied to VDD.
An open-drain port pin has a Schmitt trigger input that also has a glitch suppression
circuit.
7.15.1.3
Input-only configuration
The input-only port configuration has no output drivers. It is a Schmitt trigger input that
also has a glitch suppression circuit.
7.15.1.4
Push-pull output configuration
The push-pull output configuration has the same pull-down structure as both the
open-drain and the quasi-bidirectional output modes, but provides a continuous strong
pull-up when the port latch contains a logic 1. The push-pull mode may be used when
more source current is needed from a port output. A push-pull port pin has a
Schmitt triggered input that also has a glitch suppression circuit. The
P89LPC9151/9161/9171 device has high current source on eight pins in push-pull mode.
See Table 15 “Limiting values”.
7.15.2 Port 0 analog functions
The P89LPC9151/9161/9171 incorporates two Analog Comparators. In order to give the
best analog function performance and to minimize power consumption, pins that are being
used for analog functions must have the digital outputs and digital inputs disabled.
Digital outputs are disabled by putting the port output into the Input-Only
(high-impedance) mode.
Digital inputs on Port 0 may be disabled through the use of the PT0AD register, bits 1:5.
On any reset, PT0AD[1:5] defaults to logic 0s to enable digital functions.
7.15.3 Additional port features
After power-up, all pins are in Input-Only mode. Please note that this is different from
the LPC76x series of devices.
• After power-up, all I/O pins except P1.5, may be configured by software.
• Pin P1.5 is input only. Pins P1.2 and P1.3 are configurable for either input-only or
open-drain.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
45 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
Every output on the P89LPC9151/9161/9171 has been designed to sink typical LED drive
current. However, there is a maximum total output current for all ports which must not be
exceeded. Please refer to Table 16 “Static characteristics” for detailed specifications.
All ports pins that can function as an output have slew rate controlled outputs to limit noise
generated by quickly switching output signals. The slew rate is factory-set to
approximately 10 ns rise and fall times.
7.16 Power monitoring functions
The P89LPC9151/9161/9171 incorporates power monitoring functions designed to
prevent incorrect operation during initial power-up and power loss or reduction during
operation. This is accomplished with two hardware functions: Power-on detect and
brownout detect.
7.16.1 Brownout detection
The brownout detect function determines if the power supply voltage drops below a
certain level. Enhanced brownout detection has 3 independent functions: BOD reset,
BOD interrupt and BOD FLASH.
BOD reset is always on except in total Power-down mode. It could not be disabled in
software. BOD interrupt may be enabled or disabled in software. BOD FLASH is always
on, except in Power-down modes and could not be disabled in software.
BOD reset and BOD interrupt, each has four trip voltage levels. BOE1 bit (UCFG1.5) and
BOE0 bit (UCFG1.3) are used as trip point configuration bits of BOD reset. BOICFG1 bit
and BOICFG0 bit in register BODCFG are used as trip point configuration bits of BOD
interrupt. BOD reset voltage should be lower than BOD interrupt trip point. BOD FLASH is
used for flash programming/erase protection and has only 1 trip voltage of 2.4 V. Please
refer to P89LPC9151/9161/9171 User manual for detail configurations.
If brownout detection is enabled the brownout condition occurs when VDD falls below the
brownout trip voltage and is negated when VDD rises above the brownout trip voltage.
For correct activation of brownout detect, the VDD rise and fall times must be observed.
Please see Table 16 “Static characteristics” for specifications.
7.16.2 Power-on detection
The Power-on detect has a function similar to the brownout detect, but is designed to work
as power comes up initially, before the power supply voltage reaches a level where
brownout detect can work. The POF flag in the RSTSRC register is set to indicate an
initial power-up condition. The POF flag will remain set until cleared by software.
7.17 Power reduction modes
The P89LPC9151/9161/9171 supports three different power reduction modes. These
modes are Idle mode, Power-down mode, and total Power-down mode.
7.17.1 Idle mode
Idle mode leaves peripherals running in order to allow them to activate the processor
when an interrupt is generated. Any enabled interrupt source or reset may terminate Idle
mode.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
46 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
7.17.2 Power-down mode
The Power-down mode stops the oscillator in order to minimize power consumption. The
P89LPC9151/9161/9171 exits Power-down mode via any reset, or certain interrupts. In
Power-down mode, the power supply voltage may be reduced to the data retention supply
voltage VDDR. This retains the RAM contents at the point where Power-down mode was
entered. SFR contents are not guaranteed after VDD has been lowered to VDDR, therefore
it is highly recommended to wake-up the processor via reset in this case. VDD must be
raised to within the operating range before the Power-down mode is exited.
Some chip functions continue to operate and draw power during Power-down mode,
increasing the total power used during power-down. These include: Brownout detect,
watchdog timer, comparators (note that comparators can be powered down separately),
and RTC/system timer. The internal RC oscillator is disabled unless both the RC oscillator
has been selected as the system clock and the RTC is enabled.
7.17.3 Total Power-down mode
This is the same as Power-down mode except that the brownout detection circuitry and
the voltage comparators are also disabled to conserve additional power. The internal RC
oscillator is disabled unless both the RC oscillator has been selected as the system clock
and the RTC is enabled. If the internal RC oscillator is used to clock the RTC during
power-down, there will be high power consumption. Please use an external low frequency
clock to achieve low power with the RTC running during power-down.
7.18 Reset
The P1.5/RST pin can function as either a LOW-active reset input or as a digital input,
P1.5. The Reset Pin Enable (RPE) bit in UCFG1, when set to logic 1, enables the external
reset input function on P1.5. When cleared, P1.5 may be used as an input pin.
Remark: During a power-up sequence, the RPE selection is overridden and this pin
always functions as a reset input. An external circuit connected to this pin should not
hold this pin LOW during a power-on sequence as this will keep the device in reset.
After power-up this pin will function as defined by the RPE bit. Only a power-up reset will
temporarily override the selection defined by RPE bit. Other sources of reset will not
override the RPE bit.
Note: During a power cycle, VDD must fall below VPOR before power is reapplied, in order
to ensure a power-on reset (see Table 16 “Static characteristics”).
Reset can be triggered from the following sources:
•
•
•
•
•
•
External reset pin (during power-up or if user configured via UCFG1)
Power-on detect
Brownout detect
Watchdog timer
Software reset
UART break character detect reset
For every reset source, there is a flag in the Reset Register, RSTSRC. The user can read
this register to determine the most recent reset source. These flag bits can be cleared in
software by writing a logic 0 to the corresponding bit. More than one flag bit may be set:
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
47 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
• During a power-on reset, both POF and BOF are set but the other flag bits are
cleared.
• A Watchdog reset is similar to a power-on reset, both POF and BOF are set but the
other flag bits are cleared.
• For any other reset, previously set flag bits that have not been cleared will remain set.
7.18.1 Reset vector
Following reset, the P89LPC9151/9161/9171 will fetch instructions from either address
0000H or the Boot address. The Boot address is formed by using the boot vector as the
high byte of the address and the low byte of the address = 00H.
The boot address will be used if a UART break reset occurs, or the non-volatile boot
status bit (BOOTSTAT.0) = 1.
7.19 Timers/counters 0 and 1
The P89LPC9151/9161/9171 devices have two general purpose counter/timers which are
upward compatible with the standard 80C51 Timer 0 and Timer 1. An option to
automatically toggle the T0 pin upon timer overflow has been added. In addition an option
to toggle the T1 pin upon overflow has been added on the P89LPC9171. In the ‘Timer’
function, the register is incremented every machine cycle. In the ‘Counter’ function, the
register of Timer 0 is incremented in response to a 1-to-0 transition at its external input
pin. This external input is sampled once every machine cycle.
Timer 0 has five operating modes (Modes 0, 1, 2, 3 and 6).
Timer 1 has four operating modes (Modes 0, 1, 2, and 3), except on the P89LPC9171
where Timer 1 also has Mode 6. Modes 0, 1, 2 and 6 are the same for both
Timers/Counters. Mode 3 is different.
7.19.1 Mode 0
Putting either Timer into Mode 0 makes it look like an 8048 Timer, which is an 8-bit
Counter with a divide-by-32 prescaler. In this mode, the Timer register is configured as a
13-bit register. Mode 0 operation is the same for Timer 0 and Timer 1.
7.19.2 Mode 1
Mode 1 is the same as Mode 0, except that all 16 bits of the timer register are used.
7.19.3 Mode 2
Mode 2 configures the Timer register as an 8-bit Counter with automatic reload. Mode 2
operation is the same for Timer 0 and Timer 1.
7.19.4 Mode 3
When Timer 1 is in Mode 3 it is stopped. Timer 0 in Mode 3 forms two separate 8-bit
counters and is provided for applications that require an extra 8-bit timer. When Timer 1 is
in Mode 3 it can still be used by the serial port as a baud rate generator.
7.19.5 Mode 6
In this mode, the corresponding timer can be changed to a PWM with a full period of
256 timer clocks.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
48 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
7.19.6 Timer overflow toggle output
Timer 0 (and Timer 1 on the P89LPC9171) can be configured to automatically toggle a
port output whenever a timer overflow occurs. The same device pins that are used for the
T0 and T1 count inputs are also used for the timer toggle outputs. The port outputs will be
a logic 1 prior to the first timer overflow when this mode is turned on.
7.20 RTC/system timer
The P89LPC9151/9161/9171 has a simple RTC that allows a user to continue running an
accurate timer while the rest of the device is powered down. The RTC can be a wake-up
or an interrupt source. The RTC is a 23-bit down counter comprised of a 7-bit prescaler
and a 16-bit loadable down counter. When it reaches all logic 0s, the counter will be
reloaded again and the RTCF flag will be set.
The clock source for this counter can be either the CPU clock (CCLK) or the external clock
input, provided that the external clock input is not being used as the CPU clock. If the
external clock input is used as the CPU clock, then the RTC will use CCLK as its clock
source. Only power-on reset will reset the RTC and its associated SFRs to the default
state.
The 16-bit loadable counter portion of the RTC is readable by reading the RTCDATL and
RTCDATH registers.
7.21 UART
The P89LPC9151/9161/9171 has an enhanced UART that is compatible with the
conventional 80C51 UART except that Timer 2 overflow cannot be used as a baud rate
source. The P89LPC9151/9161/9171 does include an independent baud rate generator.
The baud rate can be selected from the oscillator (divided by a constant), Timer 1
overflow, or the independent baud rate generator. In addition to the baud rate generation,
enhancements over the standard 80C51 UART include Framing Error detection,
automatic address recognition, selectable double buffering and several interrupt options.
The UART can be operated in four modes: shift register, 8-bit UART, 9-bit UART, and CPU
clock/32 or CPU clock/16.
7.21.1 Mode 0
Serial data enters and exits through RXD. TXD outputs the shift clock. 8 bits are
transmitted or received, LSB first. The baud rate is fixed at 1⁄16 of the CPU clock
frequency.
7.21.2 Mode 1
10 bits are transmitted (through TXD) or received (through RXD): a start bit (logic 0),
8 data bits (LSB first), and a stop bit (logic 1). When data is received, the stop bit is stored
in RB8 in special function register SCON. The baud rate is variable and is determined by
the Timer 1 overflow rate or the baud rate generator (described in Section 7.21.5 “Baud
rate generator and selection”).
7.21.3 Mode 2
11 bits are transmitted (through TXD) or received (through RXD): start bit (logic 0), 8 data
bits (LSB first), a programmable 9th data bit, and a stop bit (logic 1). When data is
transmitted, the 9th data bit (TB8 in SCON) can be assigned the value of logic 0 or logic 1.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
49 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
Or, for example, the parity bit (P, in the PSW) could be moved into TB8. When data is
received, the 9th data bit goes into RB8 in special function register SCON, while the stop
bit is not saved. The baud rate is programmable to either 1⁄16 or 1⁄32 of the CPU clock
frequency, as determined by the SMOD1 bit in PCON.
7.21.4 Mode 3
11 bits are transmitted (through TXD) or received (through RXD): a start bit (logic 0), 8
data bits (LSB first), a programmable 9th data bit, and a stop bit (logic 1). In fact, Mode 3 is
the same as Mode 2 in all respects except baud rate. The baud rate in Mode 3 is variable
and is determined by the Timer 1 overflow rate or the baud rate generator (described in
Section 7.21.5 “Baud rate generator and selection”).
7.21.5 Baud rate generator and selection
The P89LPC9151/9161/9171 enhanced UART has an independent baud rate generator.
The baud rate is determined by a baud-rate preprogrammed into the BRGR1 and BRGR0
SFRs which together form a 16-bit baud rate divisor value that works in a similar manner
as Timer 1 but is much more accurate. If the baud rate generator is used, Timer 1 can be
used for other timing functions.
The UART can use either Timer 1 or the baud rate generator output (see Figure 12). Note
that Timer T1 is further divided by 2 if the SMOD1 bit (PCON.7) is cleared. The
independent baud rate generators use OSCCLK.
timer 1 overflow
(PCLK-based)
SMOD1 = 1
SBRGS = 0
÷2
baud rate modes 1 and 3
SMOD1 = 0
baud rate generator
(CCLK-based)
SBRGS = 1
002aaa897
Fig 12. Baud rate sources for UART (Modes 1, 3)
7.21.6 Framing error
Framing error is reported in the status register (SSTAT). In addition, if SMOD0 (PCON.6)
is logic 1, framing errors can be made available in SCON.7 respectively. If SMOD0 is
logic 0, SCON.7 is SM0. It is recommended that SM0 and SM1 (SCON.7:6) are set up
when SMOD0 is logic 0.
7.21.7 Break detect
Break detect is reported in the status register (SSTAT). A break is detected when
11 consecutive bits are sensed LOW. The break detect can be used to reset the device
and force the device into ISP mode.
7.21.8 Double buffering
The UART has a transmit double buffer that allows buffering of the next character to be
written to SBUF while the first character is being transmitted. Double buffering allows
transmission of a string of characters with only one stop bit between any two characters,
as long as the next character is written between the start bit and the stop bit of the
previous character.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
50 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
Double buffering can be disabled. If disabled (DBMOD, i.e., SSTAT.7 = 0), the UART is
compatible with the conventional 80C51 UART. If enabled, the UART allows writing to
SBUF while the previous data is being shifted out. Double buffering is only allowed in
Modes 1, 2 and 3. When operated in Mode 0, double buffering must be disabled
(DBMOD = 0).
7.21.9 Transmit interrupts with double buffering enabled (modes 1, 2 and 3)
Unlike the conventional UART, in double buffering mode, the TI interrupt is generated
when the double buffer is ready to receive new data.
7.21.10 The 9th bit (bit 8) in double buffering (modes 1, 2 and 3)
If double buffering is disabled TB8 can be written before or after SBUF is written, as long
as TB8 is updated some time before that bit is shifted out. TB8 must not be changed until
the bit is shifted out, as indicated by the TI interrupt.
If double buffering is enabled, TB must be updated before SBUF is written, as TB8 will be
double-buffered together with SBUF data.
7.22 I2C-bus serial interface
The I2C-bus uses two wires (SDA and SCL) to transfer information between devices
connected to the bus, and it has the following features:
• Bidirectional data transfer between masters and slaves
• Multi master bus (no central master)
• Arbitration between simultaneously transmitting masters without corruption of serial
data on the bus
• Serial clock synchronization allows devices with different bit rates to communicate via
one serial bus
• Serial clock synchronization can be used as a handshake mechanism to suspend and
resume serial transfer
• The I2C-bus may be used for test and diagnostic purposes.
A typical I2C-bus configuration is shown in Figure 13. The P89LPC9151/9161/9171
device provides a byte-oriented I2C-bus interface that supports data transfers up to
400 kHz.
RP
RP
SDA
I2C-bus
SCL
P1.3/SDA
P1.2/SCL
P89LPC9151/9161/
9171
OTHER DEVICE
WITH I2C-BUS
INTERFACE
OTHER DEVICE
WITH I2C-BUS
INTERFACE
002aae576
Fig 13. I2C-bus configuration
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
51 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
8
I2ADR
ADDRESS REGISTER
P1.3
COMPARATOR
INPUT
FILTER
P1.3/SDA
SHIFT REGISTER
OUTPUT
STAGE
ACK
I2DAT
BIT COUNTER /
ARBITRATION
AND SYNC LOGIC
INPUT
FILTER
P1.2/SCL
SERIAL CLOCK
GENERATOR
OUTPUT
STAGE
CCLK
TIMING
AND
CONTROL
LOGIC
interrupt
INTERNAL BUS
8
timer 1
overflow
P1.2
I2CON
I2SCLH
I2SCLL
CONTROL REGISTERS AND
SCL DUTY CYCLE REGISTERS
8
status bus
I2STAT
STATUS
DECODER
STATUS REGISTER
8
002aaa899
Fig 14. I2C-bus serial interface block diagram
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
52 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
7.23 SPI (P89LPC9161)
The P89LPC9161 provides another high-speed serial communication interface: the SPI
interface. SPI is a full-duplex, high-speed, synchronous communication bus with two
operation modes: Master mode and Slave mode. Up to 3 Mbit/s can be supported in either
Master mode or Slave mode. It has a Transfer Completion Flag and Write Collision Flag
Protection.
S
M
CPU clock
8-BIT SHIFT REGISTER
clock
MSTR
SPR0
SPICLK
P2.5
SS
P2.4
SPR0
SPR1
CPOL
CPHA
MSTR
SSIG
WCOL
DORD
MSTR
SPEN
SPI CONTROL
SPEN
SPR1
S
M
CLOCK LOGIC
MOSI
P2.2
SPEN
SPI clock (master)
SELECT
SPIF
PIN
CONTROL
LOGIC
READ DATA BUFFER
DIVIDER
BY 4, 16, 64, 128
MISO
P2.3
M
S
SPI CONTROL REGISTER
SPI STATUS REGISTER
SPI
interrupt
request
internal
data
bus
002aaa900
Fig 15. SPI block diagram
The SPI interface has four pins: SPICLK, MOSI, MISO and SS:
• SPICLK, MOSI and MISO are typically tied together between two or more SPI
devices. Data flows from master to slave on MOSI (Master Out Slave In) pin and flows
from slave to master on MISO (Master In Slave Out) pin. The SPICLK signal is output
in the Master mode and is input in the Slave mode. If the SPI system is disabled, i.e.,
SPEN (SPCTL.6) = 0 (reset value), these pins are configured for port functions.
• SS is the optional slave select pin. In a typical configuration, an SPI master asserts
one of its port pins to select one SPI device as the current slave. An SPI slave device
uses its SS pin to determine whether it is selected.
Typical connections are shown in Figure 16 through Figure 18.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
53 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
7.23.1 Typical SPI configurations
master
8-BIT SHIFT
REGISTER
slave
MISO
MISO
MOSI
MOSI
SPICLK
SPI CLOCK
GENERATOR
PORT
8-BIT SHIFT
REGISTER
SPICLK
SS
002aaa901
Fig 16. SPI single master single slave configuration
master
8-BIT SHIFT
REGISTER
slave
MISO
MISO
MOSI
MOSI
SPICLK
SPI CLOCK
GENERATOR
SS
8-BIT SHIFT
REGISTER
SPICLK
SS
SPI CLOCK
GENERATOR
002aaa902
Fig 17. SPI dual device configuration, where either can be a master or a slave
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
54 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
master
slave
8-BIT SHIFT
REGISTER
MISO
MISO
MOSI
MOSI
SPICLK
SPI CLOCK
GENERATOR
port
8-BIT SHIFT
REGISTER
SPICLK
SS
slave
MISO
MOSI
8-BIT SHIFT
REGISTER
SPICLK
port
SS
002aaa903
Fig 18. SPI single master multiple slaves configuration
7.24 Analog comparators
Two analog comparators are provided on the P89LPC9151/9161/9171. Input and output
options allow use of the comparators in a number of different configurations. Comparator
operation is such that the output is a logical one (which may be read in a register and/or
routed to a pin) when the positive input (one of two selectable inputs) is greater than the
negative input (selectable from a pin or an internal reference voltage). Otherwise the
output is a zero. Each comparator may be configured to cause an interrupt when the
output value changes. Comparator 1 may be output to a port pin.
The overall connections to both comparators are shown in Figure 19. The comparators
function to VDD = 2.4 V.
When each comparator is first enabled, the comparator output and interrupt flag are not
guaranteed to be stable for 10 μs. The corresponding comparator interrupt should not be
enabled during that time, and the comparator interrupt flag must be cleared before the
interrupt is enabled in order to prevent an immediate interrupt service.
When a comparator is disabled the comparator’s output, COn, goes HIGH. If the
comparator output was LOW and then is disabled, the resulting transition of the
comparator output from a LOW to HIGH state will set the comparator flag, CMFn. This will
cause an interrupt if the comparator interrupt is enabled. The user should therefore
disable the comparator interrupt prior to disabling the comparator. Additionally, the user
should clear the comparator flag, CMFn, after disabling the comparator.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
55 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
CP1
comparator 1
(P0.4) CIN1A
(P0.3) CIN1B
OE1
CO1
(P0.5) CMPREF
Vref(bg)
CMP1 (P0.6)
change detect
CMF1
CN1
interrupt
change detect
EC
CP2
CMF2
comparator 2
(P0.2) CIN2A
(P0.1) CIN2B
CMP2 (P0.0)
CO2
OE2
CN2
002aae433
Fig 19. Comparator input and output connections
7.24.1 Internal reference voltage
An internal reference voltage generator may supply a default reference when a single
comparator input pin is used. The value of the internal reference voltage, referred to as
Vref(bg), is 1.23 V ± 10 %.
7.24.2 Comparator interrupt
Each comparator has an interrupt flag contained in its configuration register. This flag is
set whenever the comparator output changes state. The flag may be polled by software or
may be used to generate an interrupt. The two comparators use one common interrupt
vector. If both comparators enable interrupts, after entering the interrupt service routine,
the user needs to read the flags to determine which comparator caused the interrupt.
7.24.3 Comparators and power reduction modes
Either or both comparators may remain enabled when Power-down or Idle mode is
activated, but both comparators are disabled automatically in Total Power-down mode.
If a comparator interrupt is enabled (except in Total Power-down mode), a change of the
comparator output state will generate an interrupt and wake-up the processor. If the
comparator output to a pin is enabled, the pin should be configured in the push-pull mode
in order to obtain fast switching times while in Power-down mode. The reason is that with
the oscillator stopped, the temporary strong pull-up that normally occurs during switching
on a quasi-bidirectional port pin does not take place.
Comparators consume power in Power-down and Idle modes, as well as in the normal
operating mode. This fact should be taken into account when system power consumption
is an issue. To minimize power consumption, the user can disable the comparators via
PCONA.5, or put the device in Total Power-down mode.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
56 of 91
NXP Semiconductors
P89LPC9151/9161/9171
8-bit microcontroller with 8-bit ADC
7.25 KBI
The Keypad Interrupt function (KBI) is intended primarily to allow a single interrupt to be
generated when Port 0 is equal to or not equal to a certain pattern. This function can be
used for bus address recognition or keypad recognition. The user can configure the port
via SFRs for different tasks.
The Keypad Interrupt Mask Register (KBMASK) is used to define which input pins
connected to Port 0 can trigger the interrupt. The Keypad Pattern Register (KBPATN) is
used to define a pattern that is compared to the value of Port 0. The Keypad Interrupt Flag
(KBIF) in the Keypad Interrupt Control Register (KBCON) is set when the condition is
matched while the Keypad Interrupt function is active. An interrupt will be generated if
enabled. The PATN_SEL bit in the Keypad Interrupt Control Register (KBCON) is used to
define equal or not-equal for the comparison.
In order to use the Keypad Interrupt as an original KBI function like in 87LPC76x series,
the user needs to set KBPATN = 0FFH and PATN_SEL = 1 (not equal), then any key
connected to Port 0 which is enabled by the KBMASK register will cause the hardware to
set KBIF and generate an interrupt if it has been enabled. The interrupt may be used to
wake-up the CPU from Idle or Power-down modes. This feature is particularly useful in
handheld, battery-powered systems that need to carefully manage power consumption
yet also need to be convenient to use.
In order to set the flag and cause an interrupt, the pattern on Port 0 must be held longer
than six CCLKs.
7.26 Watchdog timer
The watchdog timer causes a system reset when it underflows as a result of a failure to
feed the timer prior to the timer reaching its terminal count. It consists of a programmable
12-bit prescaler, and an 8-bit down counter. The down counter is decremented by a tap
taken from the prescaler. The clock source for the prescaler can be the PCLK, or the
nominal 400 kHz watchdog oscillator. The watchdog timer can only be reset by a
power-on reset. When the watchdog feature is disabled, it can be used as an interval
timer and may generate an interrupt. Figure 20 shows the watchdog timer in Watchdog
mode. Feeding the watchdog requires a two-byte sequence. If PCLK is selected as the
watchdog clock and the CPU is powered down, the watchdog is disabled. The watchdog
timer has a time-out period that ranges from a few μs to a few seconds. Please refer to the
P89LPC9151/9161/9171 User manual for more details.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
57 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
WDL (C1H)
MOV WFEED1, #0A5H
MOV WFEED2, #05AH
Watchdog
oscillator
PCLK
÷32
8-BIT DOWN
COUNTER
PRESCALER
reset(1)
SHADOW
REGISTER
FOR WDCON
CONTROL REGISTER
WDCON (A7H)
PRE2
PRE1
PRE0
–
–
WDRUN
WDTOF
WDCLK
002aae577
(1) Watchdog reset can also be caused by an invalid feed sequence, or by writing to WDCON not immediately followed by a feed
sequence.
Fig 20. Watchdog timer in Watchdog mode (WDTE = 1)
7.27 Additional features
7.27.1 Software reset
The SRST bit in AUXR1 gives software the opportunity to reset the processor completely,
as if an external reset or watchdog reset had occurred. Care should be taken when writing
to AUXR1 to avoid accidental software resets.
7.27.2 Dual data pointers
The dual Data Pointers (DPTR) provides two different Data Pointers to specify the
address used with certain instructions. The DPS bit in the AUXR1 register selects one of
the two Data Pointers. Bit 2 of AUXR1 is permanently wired as a logic 0 so that the DPS
bit may be toggled (thereby switching Data Pointers) simply by incrementing the AUXR1
register, without the possibility of inadvertently altering other bits in the register.
7.28 Flash program memory
7.28.1 General description
The P89LPC9151/9161/9171 flash memory provides in-circuit electrical erasure and
programming. The flash can be erased, read, and written as bytes. The Sector and Page
Erase functions can erase any flash sector (256 bytes) or page (16 bytes). The Chip
Erase operation will erase the entire program memory. ICP using standard commercial
programmers is available. In addition, IAP (IAP-Lite) and byte-erase allows code memory
to be used for non-volatile data storage. On-chip erase and write timing generation
contribute to a user-friendly programming interface. The P89LPC9151/9161/9171 flash
reliably stores memory contents even after 100,000 erase and program cycles. The cell is
designed to optimize the erase and programming mechanisms. The
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
58 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
P89LPC9151/9161/9171 uses VDD as the supply voltage to perform the Program/Erase
algorithms. When voltage supply is lower than 2.4 V, the BOD FLASH is tripped and flash
erase/program is blocked.
7.28.2 Features
•
•
•
•
•
•
•
•
Programming and erase over the full operating voltage range.
Byte erase allows code memory to be used for data storage.
Read/Programming/Erase using ICP.
Any flash program/erase operation in 2 ms.
Programming with industry-standard commercial programmers.
Programmable security for the code in the flash for each sector.
100,000 typical erase/program cycles for each byte.
10 year minimum data retention.
7.28.3 Flash organization
The program memory consists of eight 256-byte sectors on the P89LPC9151/9161/9171
devices. Each sector can be further divided into 16-byte pages. In addition to sector
erase, page erase, and byte erase, a 16-byte page register is included which allows from
1 byte to 16 bytes of a given page to be programmed at the same time, substantially
reducing overall programming time. In addition, erasing and reprogramming of
user-programmable configuration bytes including UCFG1, the Boot Status Bit, and the
Boot Vector is supported.
7.28.4 Using flash as data storage
The flash code memory array of this device supports individual byte erasing and
programming. Any byte in the code memory array may be read using the MOVC
instruction, provided that the sector containing the byte has not been secured (a MOVC
instruction is not allowed to read code memory contents of a secured sector). Thus any
byte in a non-secured sector may be used for non-volatile data storage.
7.28.5 Flash programming and erasing
Two different methods of erasing or programming of the flash are available. The flash may
be programmed or erased in the end-user application (IA-Lite) under control of the
application’s firmware. Another option is to use the ICP mechanism. This ICP system
provides for programming through a serial clock/serial data interface. This device does not
provide for direct verification of code memory contents. Instead, this device provides a
32-bit CRC result on either a sector or the entire user code space.
Remark: When voltage supply is lower than 2.4 V, the BOD FLASH is tripped and flash
erase/program is blocked.
7.28.6 ICP
ICP is performed without removing the microcontroller from the system. The ICP facility
consists of internal hardware resources to facilitate remote programming of the
P89LPC9151/9161/9171 through a two-wire serial interface. The NXP ICP facility has
made in-circuit programming in an embedded application - using commercially available
programmers - possible with a minimum of additional expense in components and circuit
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
59 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
board area. The ICP function uses five pins. Only a small connector needs to be available
to interface your application to a commercial programmer in order to use this feature.
Additional details may be found in the P89LPC9151/9161/9171 User manual.
7.28.7 IAP-Lite
IAP-Lite is performed in the application under the control of the microcontroller’s firmware.
The IAP facility consists of internal hardware resources to facilitate programming and
erasing. The IAP-Lite operations are accomplished through the use of four SFRs
consisting of a control/status register, a data register, and two address registers.
Additional details may be found in the P89LPC9151/9161/9171 User’s Manual.
7.29 User configuration bytes
Some user-configurable features of the P89LPC9151/9161/9171 must be defined at
power-up and therefore cannot be set by the program after start of execution. These
features are configured through the use of the flash byte UCFG1 and UCFG2. Please see
the P89LPC9151/9161/9171 User’s Manual for additional details.
7.30 User sector security bytes
There are 8 User Sector Security Bytes on the P89LPC9151/9161/9171. Each byte
corresponds to one sector. Please see the P89LPC9151/9161/9171 User manual for
additional details.
8. ADC
8.1 General description
The P89LPC9151/9161/9171 devices have a single 8-bit, 4-channel multiplexed
analog-to-digital converter. A block diagram of the A/D converter is shown in Figure 21.
The A/D consists of a 4-input multiplexer which feeds a sample-and-hold circuit providing
an input signal to one of two comparator inputs. The control logic in combination with the
SAR drives a digital-to-analog converter which provides the other input to the comparator.
The output of the comparator is fed to the SAR.
8.2 Features
8-bit, 4-channel multiplexed input, successive approximation ADC.
Four A/D result registers.
Six operating modes:
Fixed channel, single conversion mode.
Fixed channel, continuous conversion mode.
Auto scan, single conversion mode.
Auto scan, continuous conversion mode.
Dual channel, continuous conversion mode.
Single step mode.
Three conversion start modes:
Timer triggered start.
Start immediately.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
60 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC

Edge triggered.
8-bit conversion time of ≥ 1.61 μs at an A/D clock of 8.0 MHz.
Interrupt or polled operation.
Boundary limits interrupt.
DAC output to a port pin with high output impedance.
Clock divider.
Power-down mode.
8.3 Block diagram
CONTROL LOGIC
comp
INPUT
MUX
SAR
DAC1
8
cclk
002aaa783
Fig 21. ADC block diagram
8.4 ADC operating modes
8.4.1 Fixed channel, single conversion mode
A single input channel can be selected for conversion. A single conversion will be
performed and the result placed in the result register which corresponds to the selected
input channel. An interrupt, if enabled, will be generated after the conversion completes.
8.4.2 Fixed channel, continuous conversion mode
A single input channel can be selected for continuous conversion. The results of the
conversions will be sequentially placed in the four result register. The user may select
whether an interrupt can be generated after every four conversions. Additional conversion
results will again cycle through the four result register, overwriting the previous results.
Continuous conversions continue until terminated by the user.
8.4.3 Auto scan, single conversion mode
Any combination of the four input channels can be selected for conversion. A single
conversion of each selected input will be performed and the result placed in the result
register which corresponds to the selected input channel. An interrupt, if enabled, will be
generated after all selected channels have been converted. If only a single channel is
selected this is equivalent to single channel, single conversion mode.
8.4.4 Auto scan, continuous conversion mode
Any combination of the four input channels can be selected for conversion. A conversion
of each selected input will be performed and the result placed in the result register which
corresponds to the selected input channel. An interrupt, if enabled, will be generated after
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
61 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
all selected channels have been converted. The process will repeat starting with the first
selected channel. Additional conversion results will again cycle through the four result
register pairs, overwriting the previous results. Continuous conversions continue until
terminated by the user.
8.4.5 Dual channel, continuous conversion mode
This is a variation of the auto scan continuous conversion mode where conversion occurs
on two user-selectable inputs. The result of the conversion of the first channel is placed in
the result register, AD1DAT0. The result of the conversion of the second channel is placed
in result register, AD1DAT1. The first channel is again converted and its result stored in
AD1DAT2. The second channel is again converted and its result placed in AD1DAT3. An
interrupt is generated, if enabled, after every set of four conversions (two conversions per
channel).
8.4.6 Single step mode
This special mode allows ‘single-stepping’ in an auto scan conversion mode. Any
combination of the four input channels can be selected for conversion. After each channel
is converted, an interrupt is generated, if enabled, and the A/D waits for the next start
condition. May be used with any of the start modes.
8.5 Conversion start modes
8.5.1 Timer triggered start
An A/D conversion is started by the overflow of Timer 0. Once a conversion has started,
additional Timer 0 triggers are ignored until the conversion has completed. The Timer
triggered start mode is available in all ADC operating modes.
8.5.2 Start immediately
Programming this mode immediately starts a conversion. This start mode is available in all
ADC operating modes.
8.5.3 Edge triggered
An A/D conversion is started by rising or falling edge of P1.4. Once a conversion has
started, additional edge triggers are ignored until the conversion has completed. The edge
triggered start mode is available in all ADC operating modes.
8.6 Boundary limits interrupt
Each of the A/D converters has both a high and low boundary limit register. The user may
select whether an interrupt is generated when the conversion result is within (or equal to)
the high and low boundary limits or when the conversion result is outside the boundary
limits. An interrupt will be generated, if enabled, if the result meets the selected interrupt
criteria. The boundary limit may be disabled by clearing the boundary limit interrupt
enable.
An early detection mechanism exists when the interrupt criteria has been selected to be
outside the boundary limits. In this case, after the four MSBs have been converted, these
four bits are compared with the four MSBs of the boundary high and low registers. If the
four MSBs of the conversion meet the interrupt criteria (i.e., outside the boundary limits)
an interrupt will be generated, if enabled. If the four MSBs do not meet the interrupt
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
62 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
criteria, the boundary limits will again be compared after all 8 bits have been converted.
The boundary status register (BNDSTA0) flags the channels which caused a boundary
interrupt.
8.7 DAC output to a port pin with high output impedance
The DAC block of ADC1 can be output to a port pin. In this mode, the AD1DAT3 register is
used to hold the value fed to the DAC. After a value has been written to the DAC (written
to AD1DAT3), the DAC output will appear on the channel 3 pin.
8.8 Clock divider
The ADC requires that its internal clock source be in the range of 320 kHz to 8 MHz to
maintain accuracy. A programmable clock divider that divides the clock from 1 to 8 is
provided for this purpose.
8.9 Power-down and Idle mode
In Idle mode the A/C converter, if enabled, will continue to function and can cause the
device to exit Idle mode when the conversion is completed if the A/D interrupt is enabled.
In Power-down mode or Total Power-down mode, the A/D does not function. If the A/D is
enabled, it will consume power. Power can be reduced by disabling the A/D.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
63 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
9. Limiting values
Table 15. Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).[1]
Symbol
Parameter
Tamb(bias)
Conditions
Min
Max
Unit
bias ambient temperature
−55
+125
°C
Tstg
storage temperature
−65
+150
°C
IOH(I/O)
HIGH-level output current per
input/output pin
-
20
mA
IOL(I/O)
LOW-level output current per
input/output pin
-
20
mA
II/Otot(max)
maximum total input/output current
-
100
mA
Vxtal
crystal voltage
on XTAL1, XTAL2; pin to VSS
-
VDD + 0.5
V
Vn
voltage on any other pin
except XTAL1, XTAL2; pin to
VSS
−0.5
+5.5
V
Ptot(pack)
total power dissipation (per package)
based on package heat
transfer, not device power
consumption
-
1.5
W
VESD
electrostatic discharge voltage
human body model; all pins
−3000
+3000
−700
+700
[2]
charged device model; all
pins
[1]
The following applies to Table 15:
a) This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive
static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated
maximum.
b) Parameters are valid over ambient temperature range unless otherwise specified. All voltages are with respect to VSS unless
otherwise noted.
[2]
Human body model: equivalent to discharging a 100 pF capacitor through a 1.5 kΩ series resistor.
system frequency
(MHz)
18
12
2.4
2.7
3.0
VDD (V)
3.3
3.6
002aae351
Fig 22. Frequency versus supply voltage
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
64 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
10. Static characteristics
Table 16. Static characteristics
VDD = 2.4 V to 3.6 V unless otherwise specified.
Tamb = −40 °C to +85 °C for industrial applications, unless otherwise specified.
Symbol
IDD(oper)
IDD(idle)
Parameter
operating supply current
Idle mode supply current
Min
Typ[1]
Max
Unit
VDD = 3.6 V; fosc = 12 MHz
[2]
-
10
15
mA
VDD = 3.6 V; fosc = 18 MHz
[2]
-
14
23
mA
VDD = 3.6 V; fosc = 12 MHz
[3]
-
3.25
5
mA
VDD = 3.6 V; fosc = 18 MHz
[3]
-
5
7
mA
-
20
40
μA
-
1
5
μA
5
-
5000
V/S
1.5
-
-
V
Conditions
IDD(pd)
Power-down mode supply
current
VDD = 3.6 V; voltage
comparators powered down
[4]
IDD(tpd)
total Power-down mode
supply current
VDD = 3.6 V
[5]
(dV/dt)r
rise rate
of VDD; to ensure POR signal
VDDR
data retention supply
voltage
Vth(HL)
HIGH-LOW threshold
voltage
except SCL, SDA
0.22VDD
0.4VDD
-
V
VIL
LOW-level input voltage
SCL, SDA only
−0.5
-
0.3VDD
V
Vth(LH)
LOW-HIGH threshold
voltage
except SCL, SDA
-
0.6VDD
0.7VDD
V
VIH
HIGH-level input voltage
SCL, SDA only
0.7VDD
-
5.5
V
Vhys
hysteresis voltage
port 1
-
0.2VDD
-
V
IOL = 20 mA; VDD = 2.4 V to
3.6 V all ports, all modes
except high-Z
[6]
-
0.6
1.0
V
IOL = 3.2 mA; VDD = 2.4 V to
3.6 V all ports, all modes
except high-Z
[6]
-
0.2
0.3
V
IOH = −20 μA;
VDD = 2.4 V to 3.6 V; all ports,
quasi-bidirectional mode
VDD − 0.3
VDD − 0.2
-
V
IOH = −3.2 mA;
VDD = 2.4 V to 3.6 V; all ports,
push-pull mode
VDD − 0.7
VDD − 0.4
-
V
IOH = −10 mA;
VDD = 2.4 V to 3.6 V; all ports,
push-pull mode
-
3.2
-
V
[7]
−0.5
-
+5.5
V
VOL
VOH
LOW-level output voltage
HIGH-level output voltage
Vn
voltage on any other pin
Ciss
input capacitance
[8]
-
-
15
pF
IIL
LOW-level input current
VI = 0.4 V
[9]
-
-
−80
μA
ILI
input leakage current
VI = VIL, VIH, or Vth(HL)
[10]
-
-
±1
μA
all ports; VI = 1.5 V at
VDD = 3.6 V
[11]
−30
-
−450
μA
ITHL
HIGH-LOW transition
current
except VDD; with respect to
VSS
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
65 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
Table 16. Static characteristics …continued
VDD = 2.4 V to 3.6 V unless otherwise specified.
Tamb = −40 °C to +85 °C for industrial applications, unless otherwise specified.
Symbol
Parameter
RRST_N(int) internal pull-up resistance
on pin RST
Conditions
Min
Typ[1]
Max
Unit
pin RST
10
-
30
kΩ
Vref(bg)
band gap reference voltage
1.11
1.23
1.34
V
TCbg
band gap temperature
coefficient
-
10
20
ppm/
°C
[1]
Typical ratings are not guaranteed. The values listed are at room temperature, 3 V.
[2]
The IDD(oper) specification is measured using an external clock with code while(1) {} executed from on-chip flash.
[3]
The IDD(idle) specification is measured using an external clock with no active peripherals, with the following functions disabled: real-time
clock and watchdog timer.
[4]
The IDD(pd) specification is measured using internal RC oscillator with the following functions disabled: comparators, real-time clock, and
watchdog timer.
[5]
The IDD(tpd) specification is measured using an external clock with the following functions disabled: comparators, real-time clock,
brownout detect, and watchdog timer.
[6]
See Section 9 “Limiting values” for steady state (non-transient) limits on IOL or IOH. If IOL/IOH exceeds the test condition, VOL/VOH may
exceed the related specification.
[7]
This specification can be applied to pins which have A/D input or analog comparator input functions when the pin is not being used for
those analog functions. When the pin is being used as an analog input pin, the maximum voltage on the pin must be limited to 4.0 V with
respect to VSS.
[8]
Pin capacitance is characterized but not tested.
[9]
Measured with port in quasi-bidirectional mode.
[10] Measured with port in high-impedance mode.
[11] Port pins source a transition current when used in quasi-bidirectional mode and externally driven from logic 1 to logic 0. This current is
highest when VI is approximately 2 V.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
66 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
10.1 Current characteristics
Note: The graphs provided are a statistical summary based on a limited number of
samples and only for information purposes. The performance characteristics listed are not
tested or guaranteed.
002aae363
16
18 MHz
IDD
(mA)
12
12 MHz
8
8 MHz
6 MHz
4
0
2.4
4 MHz
2.8
2 MHz
1 MHz
32 kHz
3.6
3.2
VDD (V)
Test conditions: normal mode, code while(1) {} executed from on-chip flash; using an external
clock.
Fig 23. IDD(oper) versus frequency at +25 °C
002aae364
16
18 MHz
IDD
(mA)
12
12 MHz
8
8 MHz
6 MHz
4
0
2.4
4 MHz
2.8
2 MHz
1 MHz
32 kHz
3.6
3.2
VDD (V)
Test conditions: normal mode, code while(1) {} executed from on-chip flash; using an external
clock.
Fig 24. IDD(oper) versus frequency at −40 °C
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
67 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
002aae365
16
18 MHz
IDD
(mA)
12
12 MHz
8
8 MHz
6 MHz
4
0
2.4
4 MHz
2.8
2 MHz
1 MHz
32 kHz
3.6
3.2
VDD (V)
Test conditions: normal mode, code while(1) {} executed from on-chip flash; using an external
clock.
Fig 25. IDD(oper) versus frequency at +85 °C
002aae366
5.0
18 MHz
IDD
(mA)
4.0
12 MHz
3.0
8 MHz
2.0
6 MHz
4 MHz
1.0
0.0
2.4
2 MHz
1 MHz
32 kHz
2.8
3.2
3.6
VDD (V)
Test conditions: idle mode entered executing code from on-chip flash; using an external clock with
no active peripherals, with the following functions disabled: real-time clock and watchdog timer.
Fig 26. IDD(idle) versus frequency at +25 °C
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
68 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
002aae367
5.0
18 MHz
IDD
(mA)
4.0
12 MHz
3.0
8 MHz
2.0
6 MHz
4 MHz
1.0
0.0
2.4
2 MHz
1 MHz
32 kHz
2.8
3.2
3.6
VDD (V)
Test conditions: idle mode entered executing code from on-chip flash; using an external clock with
no active peripherals, with the following functions disabled: real-time clock and watchdog timer.
Fig 27. IDD(idle) versus frequency at −40 °C
002aae368
5.0
18 MHz
IDD
(mA)
4.0
12 MHz
3.0
8 MHz
2.0
6 MHz
4 MHz
1.0
0.0
2.4
2 MHz
1 MHz
32 kHz
2.8
3.2
3.6
VDD (V)
Test conditions: idle mode entered executing code from on-chip flash; using an external clock with
no active peripherals, with the following functions disabled: real-time clock and watchdog timer.
Fig 28. IDD(idle) versus frequency at +85 °C
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
69 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
002aae369
20.0
IDD
(μA)
(1)
18.0
16.0
(2)
14.0
(3)
12.0
10.0
2.4
2.8
3.2
3.6
VDD (V)
Test conditions: power-down mode, using internal RC oscillator with the following functions
disabled: comparators, real-time clock, and watchdog timer.
(1) +85 °C
(2) +25 °C
(3) −40 °C
Fig 29. IDD(pd) versus VDD
002aae370
1.2
(1)
IDD
(μA)
0.8
0.4
(2)
(3)
0.0
2.4
2.8
3.2
3.6
VDD (V)
Test conditions: Total power-down mode, using internal RC oscillator with the following functions
disabled: comparators, brownout detect, real-time clock, and watchdog timer.
(1) +85 °C
(2) −40 °C
(3) +25 °C
Fig 30. IDD(tpd) versus VDD
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
70 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
10.2 Internal RC/watchdog oscillator characteristics
Note: The graphs provided are a statistical summary based on a limited number of
samples and only for information purposes. The performance characteristics listed are not
tested or guaranteed.
002aae344
0.2
frequency
deviation
(%)
0.1
0
−0.1
−0.2
2.4
2.8
3.2
3.6
VDD (V)
Central frequency of internal RC oscillator = 7.3728 MHz
Fig 31. Average internal RC oscillator frequency versus VDD at +25 °C
002aae346
0.2
frequency
deviation
(%)
0.1
0
−0.1
−0.2
2.4
2.8
3.2
3.6
VDD (V)
Note: Central frequency of internal RC oscillator = 7.3728 MHz
Fig 32. Average internal RC oscillator frequency versus VDD at −40 °C
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
71 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
002aae347
0.2
frequency
deviation
(%)
0
−0.2
−0.4
−0.6
2.4
2.8
3.2
3.6
VDD (V)
Central frequency of internal RC oscillator = 7.3728 MHz
Fig 33. Average internal RC oscillator frequency versus VDD at +85 °C
002aae348
2.5
frequency
deviation
(%)
1.5
0.5
−0.5
−1.5
2.4
2.8
3.2
3.6
VDD (V)
Central frequency of watchdog oscillator = 400 kHz
Fig 34. Average watchdog oscillator frequency versus VDD at +25 °C
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
72 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
002aae349
0.5
frequency
deviation
(%)
−0.5
−1.5
−2.5
−3.5
2.4
2.8
3.2
3.6
VDD (V)
Central frequency of watchdog oscillator = 400 kHz
Fig 35. Average watchdog oscillator frequency versus VDD at −40 °C
002aae350
1.5
frequency
deviation
(%)
0.5
−0.5
−1.5
−2.5
2.4
2.8
3.2
3.6
VDD (V)
Central frequency of watchdog oscillator = 400 kHz
Fig 36. Average watchdog oscillator frequency versus VDD at +85 °C
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
73 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
10.3 BOD characteristics
Table 17. BOD static characteristics
VDD = 2.4 V to 3.6 V unless otherwise specified.
Tamb = −40 °C to +85 °C for industrial applications, unless otherwise specified.
Symbol
Parameter
Min
Typ[1]
Max
Unit
BOICFG1, BOICFG0 = 01
2.25
-
2.55
V
BOICFG1, BOICFG0 = 10
2.60
-
2.80
V
BOICFG1, BOICFG0 = 11
3.10
-
3.40
V
BOICFG1, BOICFG0 = 01
2.30
-
2.60
V
BOICFG1, BOICFG0 = 10
2.70
-
2.90
V
BOICFG1, BOICFG0 = 11
3.15
-
3.45
V
BOE1, BOE0 = 01
2.10
-
2.30
V
BOE1, BOE0 = 10
2.25
-
2.55
V
BOE1, BOE0 = 11
2.80
-
3.20
V
BOE1, BOE0 = 01
2.20
-
2.40
V
BOE1, BOE0 = 10
2.30
-
2.60
V
BOE1, BOE0 = 11
2.90
-
3.30
V
falling stage
2.25
-
2.55
V
rising stage
2.30
-
2.60
V
Conditions
BOD interrupt
Vtrip
trip voltage
falling stage
rising stage
BOD reset
Vtrip
trip voltage
falling stage
rising stage
BOD EEPROM/FLASH
Vtrip
[1]
trip voltage
Typical ratings are not guaranteed. The values listed are at room temperature, 3 V.
VDD
Vtrip
(BOF/BOIF
set by hardware)
(BOF/BOIF can be
cleared in software)
BOF/BOIF
002aae352
Fig 37. BOD interrupt/reset characteristics
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
74 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
11. Dynamic characteristics
Table 18. Dynamic characteristics (12 MHz)
VDD = 2.4 V to 3.6 V unless otherwise specified.
Tamb = −40 °C to +85 °C for industrial applications, unless otherwise specified.[1][2]
Symbol
Parameter
Conditions
Min
Max
Min
fosc(RC)
internal RC oscillator
frequency
nominal f = 7.3728 MHz
trimmed to ±1 % at
Tamb = 25 °C; clock
doubler option = OFF
(default)
7.189
7.557
7.189
nominal f = 14.7456 MHz;
clock doubler option = ON,
VDD = 2.7 V to 3.6 V
14.378
15.114
14.378 15.114 MHz
380
420
380
420
kHz
0
12
-
-
MHz
83
-
-
-
ns
0
8
-
-
MHz
P1.5/RST pin
-
50
-
50
ns
any pin except P1.5/RST
-
15
-
15
ns
P1.5/RST pin
125
-
125
-
ns
any pin except P1.5/RST
50
-
50
-
ns
fosc(WD)
internal watchdog
oscillator frequency
fosc
oscillator frequency
Tcy(clk)
clock cycle time
fCLKLP
low-power select clock
frequency
Tamb = 25 °C
see Figure 38
Variable clock
fosc = 12 MHz
Unit
Max
7.557 MHz
Glitch filter
tgr
tsa
glitch rejection time
signal acceptance time
External clock
tCHCX
clock HIGH time
see Figure 38
33
Tcy(clk) − tCLCX
33
-
ns
tCLCX
clock LOW time
see Figure 38
33
Tcy(clk) − tCHCX
33
-
ns
tCLCH
clock rise time
see Figure 38
-
8
-
8
ns
tCHCL
clock fall time
see Figure 38
-
8
-
8
ns
Shift register (UART mode 0)
TXLXL
serial port clock cycle
time
see Figure 39
16Tcy(clk)
-
1333
-
ns
tQVXH
output data set-up to
clock rising edge time
see Figure 39
13Tcy(clk)
-
1083
-
ns
tXHQX
output data hold after
clock rising edge time
see Figure 39
-
Tcy(clk) + 20
-
103
ns
tXHDX
input data hold after
clock rising edge time
see Figure 39
-
0
-
0
ns
tXHDV
input data valid to clock
rising edge time
see Figure 39
150
-
150
-
ns
0
CCLK⁄
6
0
2.0
MHz
-
CCLK⁄
4
-
3.0
MHz
SPI interface
fSPI
SPI operating frequency
slave
master
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
75 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
Table 18. Dynamic characteristics (12 MHz) …continued
VDD = 2.4 V to 3.6 V unless otherwise specified.
Tamb = −40 °C to +85 °C for industrial applications, unless otherwise specified.[1][2]
Symbol
Parameter
Conditions
Variable clock
Min
TSPICYC
SPI cycle time
Max
see Figure 40, 41, 42, 43
CCLK
-
500
-
ns
master
4⁄
CCLK
-
333
-
ns
250
-
250
-
ns
250
-
250
-
ns
tSPILAG
SPI enable lag time
see Figure 42, 43
slave
see Figure 42, 43
slave
tSPIDSU
Min
6⁄
SPI enable lead time
tSPICLKL
Max
Unit
slave
tSPILEAD
tSPICLKH
fosc = 12 MHz
SPICLK HIGH time
see Figure 40, 41, 42, 43
master
2⁄
CCLK
-
165
-
ns
slave
3⁄
CCLK
-
250
-
ns
master
2⁄
CCLK
-
165
-
ns
slave
3⁄
SPICLK LOW time
SPI data set-up time
see Figure 40, 41, 42, 43
CCLK
-
250
-
ns
see Figure 40, 41, 42, 43
100
-
100
-
ns
see Figure 40, 41, 42, 43
100
-
100
-
ns
0
120
0
120
ns
0
240
-
240
ns
-
240
-
240
ns
master or slave
tSPIDH
SPI data hold time
tSPIA
SPI access time
master or slave
see Figure 42, 43
slave
tSPIDIS
SPI disable time
tSPIDV
SPI enable to output
data valid time
see Figure 42, 43
slave
see Figure 40, 41, 42, 43
slave
master
-
167
-
167
ns
0
-
0
-
ns
SPI outputs (SPICLK,
MOSI, MISO)
-
100
-
100
ns
SPI inputs (SPICLK,
MOSI, MISO, SS)
-
2000
-
2000
ns
SPI outputs (SPICLK,
MOSI, MISO)
-
100
-
100
ns
SPI inputs (SPICLK,
MOSI, MISO, SS)
-
2000
-
2000
ns
tSPIOH
SPI output data hold
time
see Figure 40, 41, 42, 43
tSPIR
SPI rise time
see Figure 40, 41, 42, 43
tSPIF
SPI fall time
see Figure 40, 41, 42, 43
[1]
Parameters are valid over operating temperature range unless otherwise specified.
[2]
Parts are tested to 2 MHz, but are guaranteed to operate down to 0 Hz.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
76 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
Table 19. Dynamic characteristics (18 MHz)
VDD = 3.0 V to 3.6 V unless otherwise specified.
Tamb = −40 °C to +85 °C for industrial applications, unless otherwise specified.[1][2]
Symbol Parameter
fosc(RC)
internal RC oscillator
frequency
fosc(WD)
internal watchdog
oscillator frequency
fosc
oscillator frequency
Tcy(clk)
clock cycle time
fCLKLP
low-power select clock
frequency
Conditions
Variable clock
fosc = 18 MHz
Unit
Min
Max
Min
nominal f = 7.3728 MHz
trimmed to ±1 % at
Tamb = 25 °C; clock
doubler option = OFF
(default)
7.189
7.557
7.189
nominal f = 14.7456 MHz;
clock doubler option = ON
14.378
15.114
14.378 15.114 MHz
380
420
380
420
kHz
0
18
-
-
MHz
55
-
-
-
ns
0
8
-
-
MHz
P1.5/RST pin
-
50
-
50
ns
any pin except P1.5/RST
-
15
-
15
ns
P1.5/RST pin
125
-
125
-
ns
any pin except P1.5/RST
50
-
50
-
ns
Tamb = 25 °C
see Figure 38
Max
7.557 MHz
Glitch filter
tgr
tsa
glitch rejection time
signal acceptance time
External clock
tCHCX
clock HIGH time
see Figure 38
22
Tcy(clk) − tCLCX
22
-
ns
tCLCX
clock LOW time
see Figure 38
22
Tcy(clk) − tCHCX
22
-
ns
tCLCH
clock rise time
see Figure 38
-
5
-
5
ns
tCHCL
clock fall time
see Figure 38
-
5
-
5
ns
Shift register (UART mode 0)
TXLXL
serial port clock cycle
time
see Figure 39
16Tcy(clk)
-
888
-
ns
tQVXH
output data set-up to
clock rising edge time
see Figure 39
13Tcy(clk)
-
722
-
ns
tXHQX
output data hold after
clock rising edge time
see Figure 39
-
Tcy(clk) + 20
-
75
ns
tXHDX
input data hold after
clock rising edge time
see Figure 39
-
0
-
0
ns
tXHDV
input data valid to clock
rising edge time
see Figure 39
150
-
150
-
ns
0
CCLK⁄
6
0
3.0
MHz
-
CCLK⁄
4
-
4.5
MHz
SPI interface
fSPI
SPI operating frequency
slave
master
TSPICYC
SPI cycle time
see Figure 40, 41, 42, 43
slave
6⁄
CCLK
-
333
-
ns
master
4⁄
CCLK
-
222
-
ns
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
77 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
Table 19. Dynamic characteristics (18 MHz) …continued
VDD = 3.0 V to 3.6 V unless otherwise specified.
Tamb = −40 °C to +85 °C for industrial applications, unless otherwise specified.[1][2]
Symbol Parameter
tSPILEAD
SPI enable lead time
Conditions
Variable clock
SPI enable lag time
tSPICLKL
tSPIDSU
SPICLK HIGH time
-
250
-
ns
250
-
250
-
ns
CCLK
-
167
-
ns
master
CCLK
-
111
-
ns
slave
3⁄
CCLK
-
167
-
ns
master
2⁄
CCLK
-
111
-
ns
100
-
100
-
ns
100
-
100
-
ns
0
80
0
80
ns
0
160
-
160
ns
slave
-
160
-
160
ns
master
-
111
-
111
ns
0
-
0
-
ns
SPI outputs (SPICLK,
MOSI, MISO)
-
100
-
100
ns
SPI inputs (SPICLK,
MOSI, MISO, SS)
-
2000
-
2000
ns
SPI outputs (SPICLK,
MOSI, MISO)
-
100
-
100
ns
SPI inputs (SPICLK,
MOSI, MISO, SS)
-
2000
-
2000
ns
SPICLK LOW time
SPI data set-up time
see Figure 40, 41, 42, 43
see Figure 40, 41, 42, 43
SPI data hold time
see Figure 40, 41, 42, 43
SPI access time
see Figure 42, 43
SPI disable time
see Figure 42, 43
SPI enable to output
data valid time
see Figure 40, 41, 42, 43
tSPIOH
SPI output data hold
time
see Figure 40, 41, 42, 43
tSPIR
SPI rise time
see Figure 40, 41, 42, 43
tSPIF
250
2⁄
slave
tSPIDV
Max
3⁄
slave
tSPIDIS
Min
see Figure 40, 41, 42, 43
master or slave
tSPIA
Max
slave
master or slave
tSPIDH
Min
see Figure 42, 43
slave
tSPICLKH
Unit
see Figure 42, 43
slave
tSPILAG
fosc = 18 MHz
SPI fall time
see Figure 40, 41, 42, 43
[1]
Parameters are valid over operating temperature range unless otherwise specified.
[2]
Parts are tested to 2 MHz, but are guaranteed to operate down to 0 Hz.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
78 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
11.1 Waveforms
tCHCL
tCHCX
tCLCH
tCLCX
Tcy(clk)
002aaa907
Fig 38. External clock timing (with an amplitude of at least Vi(RMS) = 200 mV)
TXLXL
clock
tXHQX
tQVXH
output data
0
write to SBUF
input data
1
2
3
4
5
6
tXHDX
set TI
tXHDV
valid
7
valid
valid
valid
valid
valid
valid
valid
clear RI
set RI
002aaa906
Fig 39. Shift register mode timing
SS
TSPICYC
tSPIF
tSPICLKH
tSPICLKL
tSPIR
SPICLK
(CPOL = 0)
(output)
tSPIF
tSPICLKL
tSPIR
tSPICLKH
SPICLK
(CPOL = 1)
(output)
tSPIDSU
MISO
(input)
tSPIDH
tSPIDV
MOSI
(output)
LSB/MSB in
MSB/LSB in
tSPIOH
tSPIDV
tSPIR
tSPIF
master MSB/LSB out
master LSB/MSB out
002aaa908
Fig 40. SPI master timing (CPHA = 0)
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
79 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
SS
TSPICYC
tSPIF
tSPICLKL
tSPIR
tSPICLKH
SPICLK
(CPOL = 0)
(output)
tSPIF
tSPICLKL
tSPICLKH
SPICLK
(CPOL = 1)
(output)
tSPIDSU
MISO
(input)
tSPIDH
LSB/MSB in
MSB/LSB in
tSPIDV
MOSI
(output)
tSPIR
tSPIOH
tSPIDV
tSPIF
tSPIR
master MSB/LSB out
master LSB/MSB out
002aaa909
Fig 41. SPI master timing (CPHA = 1)
SS
tSPIF
tSPIR
TSPICYC
tSPILEAD
tSPIF
tSPICLKH
tSPICLKL
tSPIR
tSPILAG
SPICLK
(CPOL = 0)
(input)
tSPIF
tSPICLKL
tSPIR
tSPICLKH
SPICLK
(CPOL = 1)
(input)
tSPIOH
tSPIA
tSPIOH
MISO
(output)
slave MSB/LSB out
tSPIDSU
MOSI
(input)
tSPIOH
tSPIDH
tSPIDIS
tSPIDV
tSPIDV
slave LSB/MSB out
tSPIDSU
tSPIDSU
MSB/LSB in
not defined
tSPIDH
LSB/MSB in
002aaa910
Fig 42. SPI slave timing (CPHA = 0)
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
80 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
SS
tSPIF
tSPIR
TSPICYC
tSPIF
tSPILEAD
tSPICLKL
tSPIR
tSPILAG
tSPICLKH
SPICLK
(CPOL = 0)
(input)
tSPIF
tSPICLKL
SPICLK
(CPOL = 1)
(input)
tSPIR
tSPICLKH
tSPIOH
tSPIOH
tSPIDV
tSPIDV
tSPIOH
tSPIDV
tSPIDIS
tSPIA
MISO
(output)
slave LSB/MSB out
slave MSB/LSB out
not defined
tSPIDSU
MOSI
(input)
tSPIDH
tSPIDSU
MSB/LSB in
tSPIDH
LSB/MSB in
002aaa911
Fig 43. SPI slave timing (CPHA = 1)
12. Other characteristics
12.1 Comparator electrical characteristics
Table 20. Comparator electrical characteristics
VDD = 2.4 V to 3.6 V, unless otherwise specified.
Tamb = −40 °C to +85 °C for industrial applications, unless otherwise specified.
Symbol
Parameter
VIO
input offset voltage
VIC
common-mode input voltage
Conditions
[1]
Min
Typ
Max
Unit
-
-
±20
mV
0
-
VDD − 0.3
V
-
-
−50
dB
CMRR
common-mode rejection ratio
tres(tot)
total response time
-
250
500
ns
t(CE-OV)
chip enable to output valid time
-
-
10
μs
ILI
input leakage current
-
-
±1
μA
[1]
0 V < VI < VDD
This parameter is characterized, but not tested in production.
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
81 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
12.2 ADC electrical characteristics
Table 21. ADC/temperature sensor electrical characteristics
VDD = 2.4 V to 3.6 V, unless otherwise specified.
Tamb = −40 °C to +85 °C for industrial applications, unless otherwise specified.
All limits valid for an external source impedance of less than 10 kΩ.
Symbol
Parameter
VDDA(ADC)
ADC analog supply voltage
Conditions
VSSA
analog ground voltage
VIA
analog input voltage
Cia
ED
Min
Max
Unit
VSS − 0.2 -
VDD + 0.2
V
analog input capacitance
-
-
15
pF
differential linearity error
-
-
±1
LSB
EL(adj)
integral non-linearity
-
-
±1
LSB
EO
offset error
-
-
±2
LSB
EG
gain error
-
-
±1
%
Eu(tot)
total unadjusted error
-
-
±2
LSB
MCTC
channel-to-channel matching
-
-
±1
LSB
αct(port)
crosstalk between port inputs
-
-
−60
dB
SRin
input slew rate
-
-
100
V/ms
Tcy(ADC)
ADC clock cycle time
111
-
2000
ns
tADC
ADC conversion time
-
-
13Tcy(ADC)
μs
0 kHz to 100 kHz
ADC enabled
Typ
start trigger
adc_clk
1
2
3
4
5
6
7
8
9
10
11
12
13
clk
serial_data_out
D7
D6
D5
D4
ADCDATA_REG
D3
D2
D1
D0
ADCDATA
002aae371
Fig 44. ADC conversion timing
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
82 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
offset
error
EO
gain
error
EG
255
254
253
252
(2)
7
code
out
(1)
6
5
4
3
2
1 LSB
(ideal)
1
0
1
2
3
4
offset error
EO
5
6
253
7
254
255
256
VIA (LSBideal)
1 LSB =
VDDA − VSSA
256
002aae372
(1) Example of an actual transfer curve.
(2) The ideal transfer curve.
Fig 45. ADC characteristics
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
83 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
13. Package outline
TSSOP14: plastic thin shrink small outline package; 14 leads; body width 4.4 mm
SOT402-1
E
D
A
X
c
y
HE
v M A
Z
8
14
Q
(A 3)
A2
A
A1
pin 1 index
θ
Lp
L
1
7
e
detail X
w M
bp
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (2)
e
HE
L
Lp
Q
v
w
y
Z (1)
θ
mm
1.1
0.15
0.05
0.95
0.80
0.25
0.30
0.19
0.2
0.1
5.1
4.9
4.5
4.3
0.65
6.6
6.2
1
0.75
0.50
0.4
0.3
0.2
0.13
0.1
0.72
0.38
8
o
0
o
Notes
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
2. Plastic interlead protrusions of 0.25 mm maximum per side are not included.
OUTLINE
VERSION
SOT402-1
REFERENCES
IEC
JEDEC
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
99-12-27
03-02-18
MO-153
Fig 46. TSSOP14 package outline (SOT402-1)
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
84 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm
SOT403-1
E
D
A
X
c
y
HE
v M A
Z
9
16
Q
(A 3)
A2
A
A1
pin 1 index
θ
Lp
L
1
8
e
detail X
w M
bp
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (2)
e
HE
L
Lp
Q
v
w
y
Z (1)
θ
mm
1.1
0.15
0.05
0.95
0.80
0.25
0.30
0.19
0.2
0.1
5.1
4.9
4.5
4.3
0.65
6.6
6.2
1
0.75
0.50
0.4
0.3
0.2
0.13
0.1
0.40
0.06
8
o
0
o
Notes
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
2. Plastic interlead protrusions of 0.25 mm maximum per side are not included.
OUTLINE
VERSION
SOT403-1
REFERENCES
IEC
JEDEC
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
99-12-27
03-02-18
MO-153
Fig 47. TSSOP16 package outline (SOT403-1)
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
85 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
14. Abbreviations
Table 22.
Abbreviations
Acronym
Description
ADC
Analog to Digital Converter
BOD
Brownout Detection
CPU
Central Processing Unit
DAC
Digital to Analog Converter
EEPROM
Electrically Erasable Programmable Read-Only Memory
EPROM
Erasable Programmable Read-Only Memory
EMI
ElectroMagnetic Interference
IRC
Internal RC
LSB
Least Significant Bit
MSB
Most Significant Bit
PLL
Phase-Locked Loop
PWM
Pulse Width Modulator
RAM
Random Access Memory
RC
Resistance-Capacitance
RTC
Real-Time Clock
SAR
Successive Approximation Register
SCL
Serial Clock Line
SDA
Serial DAta line
SFR
Special Function Register
SPI
Serial Peripheral Interface
UART
Universal Asynchronous Receiver/Transmitter
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
86 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
15. Revision history
Table 23.
Revision history
Document ID
Release date
Data sheet status
Change notice
Supersedes
P89LPC9151_61_71_2
20100209
Product data sheet
-
P89LPC9151_61_71_1
Modifications:
P89LPC9151_61_71_1
•
Changed data sheet status to "Product data sheet".
20091209
Preliminary data sheet
P89LPC9151_61_71_2
Product data sheet
-
-
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
87 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
16. Legal information
16.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
16.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
16.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on a weakness or default in the
customer application/use or the application/use of customer’s third party
customer(s) (hereinafter both referred to as “Application”). It is customer’s
sole responsibility to check whether the NXP Semiconductors product is
suitable and fit for the Application planned. Customer has to do all necessary
testing for the Application in order to avoid a default of the Application and the
product. NXP Semiconductors does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from national authorities.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
Non-automotive qualified products — Unless the data sheet of an NXP
Semiconductors product expressly states that the product is automotive
qualified, the product is not suitable for automotive use. It is neither qualified
nor tested in accordance with automotive testing or application requirements.
NXP Semiconductors accepts no liability for inclusion and/or use of
non-automotive qualified products in automotive equipment or applications.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in medical, military, aircraft,
space or life support equipment, nor in applications where failure or
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
88 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
16.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
I2C-bus — logo is a trademark of NXP B.V.
17. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
continued >>
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
89 of 91
P89LPC9151/9161/9171
NXP Semiconductors
8-bit microcontroller with 8-bit ADC
18. Contents
1
General description . . . . . . . . . . . . . . . . . . . . . . 1
2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2.1
Principal features . . . . . . . . . . . . . . . . . . . . . . . 1
2.2
Additional features . . . . . . . . . . . . . . . . . . . . . . 2
3
Ordering information . . . . . . . . . . . . . . . . . . . . . 3
3.1
Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 3
4
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4
5
Functional diagram . . . . . . . . . . . . . . . . . . . . . . 7
6
Pinning information . . . . . . . . . . . . . . . . . . . . . . 9
6.1
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6.2
Pin description . . . . . . . . . . . . . . . . . . . . . . . . 10
7
Functional description . . . . . . . . . . . . . . . . . . 16
7.1
Special function registers . . . . . . . . . . . . . . . . 16
7.2
Enhanced CPU . . . . . . . . . . . . . . . . . . . . . . . . 38
7.3
Clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
7.3.1
Clock definitions . . . . . . . . . . . . . . . . . . . . . . . 38
7.3.2
CPU clock (OSCCLK). . . . . . . . . . . . . . . . . . . 38
7.4
Clock output (P89LPC9171) . . . . . . . . . . . . . . 38
7.5
On-chip RC oscillator option . . . . . . . . . . . . . . 38
7.6
Watchdog oscillator option . . . . . . . . . . . . . . . 39
7.7
External clock input option . . . . . . . . . . . . . . . 39
7.8
Clock sources switch on the fly. . . . . . . . . . . . 39
7.9
CCLK wake-up delay . . . . . . . . . . . . . . . . . . . 40
7.10
CCLK modification: DIVM register . . . . . . . . . 40
7.11
Low power select . . . . . . . . . . . . . . . . . . . . . . 40
7.12
Memory organization . . . . . . . . . . . . . . . . . . . 41
7.13
Data RAM arrangement . . . . . . . . . . . . . . . . . 41
7.14
Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
7.14.1
External interrupt inputs . . . . . . . . . . . . . . . . . 42
7.15
I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
7.15.1
Port configurations . . . . . . . . . . . . . . . . . . . . . 44
7.15.1.1 Quasi-bidirectional output configuration . . . . . 44
7.15.1.2 Open-drain output configuration . . . . . . . . . . . 45
7.15.1.3 Input-only configuration . . . . . . . . . . . . . . . . . 45
7.15.1.4 Push-pull output configuration . . . . . . . . . . . . 45
7.15.2
Port 0 analog functions . . . . . . . . . . . . . . . . . . 45
7.15.3
Additional port features. . . . . . . . . . . . . . . . . . 45
7.16
Power monitoring functions . . . . . . . . . . . . . . 46
7.16.1
Brownout detection . . . . . . . . . . . . . . . . . . . . . 46
7.16.2
Power-on detection. . . . . . . . . . . . . . . . . . . . . 46
7.17
Power reduction modes . . . . . . . . . . . . . . . . . 46
7.17.1
Idle mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
7.17.2
Power-down mode . . . . . . . . . . . . . . . . . . . . . 47
7.17.3
Total Power-down mode . . . . . . . . . . . . . . . . . 47
7.18
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
7.18.1
Reset vector . . . . . . . . . . . . . . . . . . . . . . . . . . 48
7.19
Timers/counters 0 and 1 . . . . . . . . . . . . . . . . . 48
7.19.1
7.19.2
7.19.3
7.19.4
7.19.5
7.19.6
7.20
7.21
7.21.1
7.21.2
7.21.3
7.21.4
7.21.5
7.21.6
7.21.7
7.21.8
7.21.9
Mode 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Mode 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Mode 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Timer overflow toggle output . . . . . . . . . . . . . 49
RTC/system timer . . . . . . . . . . . . . . . . . . . . . 49
UART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Mode 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Mode 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Baud rate generator and selection. . . . . . . . . 50
Framing error . . . . . . . . . . . . . . . . . . . . . . . . . 50
Break detect. . . . . . . . . . . . . . . . . . . . . . . . . . 50
Double buffering. . . . . . . . . . . . . . . . . . . . . . . 50
Transmit interrupts with double buffering enabled
(modes 1, 2 and 3). . . . . . . . . . . . . . . . . . . . . 51
7.21.10 The 9th bit (bit 8) in double buffering (modes 1, 2
and 3). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
7.22
I2C-bus serial interface. . . . . . . . . . . . . . . . . . 51
7.23
SPI (P89LPC9161) . . . . . . . . . . . . . . . . . . . . 53
7.23.1
Typical SPI configurations . . . . . . . . . . . . . . . 54
7.24
Analog comparators . . . . . . . . . . . . . . . . . . . . 55
7.24.1
Internal reference voltage . . . . . . . . . . . . . . . 56
7.24.2
Comparator interrupt . . . . . . . . . . . . . . . . . . . 56
7.24.3
Comparators and power reduction modes . . . 56
7.25
KBI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
7.26
Watchdog timer . . . . . . . . . . . . . . . . . . . . . . . 57
7.27
Additional features . . . . . . . . . . . . . . . . . . . . . 58
7.27.1
Software reset . . . . . . . . . . . . . . . . . . . . . . . . 58
7.27.2
Dual data pointers . . . . . . . . . . . . . . . . . . . . . 58
7.28
Flash program memory . . . . . . . . . . . . . . . . . 58
7.28.1
General description . . . . . . . . . . . . . . . . . . . . 58
7.28.2
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
7.28.3
Flash organization . . . . . . . . . . . . . . . . . . . . . 59
7.28.4
Using flash as data storage . . . . . . . . . . . . . . 59
7.28.5
Flash programming and erasing . . . . . . . . . . 59
7.28.6
ICP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
7.28.7
IAP-Lite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
7.29
User configuration bytes . . . . . . . . . . . . . . . . 60
7.30
User sector security bytes . . . . . . . . . . . . . . . 60
8
ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
8.1
General description . . . . . . . . . . . . . . . . . . . . 60
8.2
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
8.3
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . 61
8.4
ADC operating modes . . . . . . . . . . . . . . . . . . 61
8.4.1
Fixed channel, single conversion mode. . . . . 61
continued >>
P89LPC9151_61_71_2
Product data sheet
© NXP B.V. 2010. All rights reserved.
Rev. 02 — 9 February 2010
90 of 91
NXP Semiconductors
P89LPC9151/9161/9171
8-bit microcontroller with 8-bit ADC
8.4.2
8.4.3
8.4.4
8.4.5
8.4.6
8.5
8.5.1
8.5.2
8.5.3
8.6
8.7
8.8
8.9
9
10
10.1
10.2
10.3
11
11.1
12
12.1
12.2
13
14
15
16
16.1
16.2
16.3
16.4
17
18
Fixed channel, continuous conversion mode . 61
Auto scan, single conversion mode . . . . . . . . 61
Auto scan, continuous conversion mode . . . . 61
Dual channel, continuous conversion mode . . 62
Single step mode . . . . . . . . . . . . . . . . . . . . . . 62
Conversion start modes . . . . . . . . . . . . . . . . . 62
Timer triggered start . . . . . . . . . . . . . . . . . . . . 62
Start immediately . . . . . . . . . . . . . . . . . . . . . . 62
Edge triggered . . . . . . . . . . . . . . . . . . . . . . . . 62
Boundary limits interrupt . . . . . . . . . . . . . . . . . 62
DAC output to a port pin with high output
impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Clock divider . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Power-down and Idle mode . . . . . . . . . . . . . . 63
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 64
Static characteristics. . . . . . . . . . . . . . . . . . . . 65
Current characteristics . . . . . . . . . . . . . . . . . . 67
Internal RC/watchdog oscillator characteristics 71
BOD characteristics . . . . . . . . . . . . . . . . . . . . 74
Dynamic characteristics . . . . . . . . . . . . . . . . . 75
Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Other characteristics . . . . . . . . . . . . . . . . . . . . 81
Comparator electrical characteristics . . . . . . . 81
ADC electrical characteristics . . . . . . . . . . . . . 82
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 84
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Revision history . . . . . . . . . . . . . . . . . . . . . . . . 87
Legal information. . . . . . . . . . . . . . . . . . . . . . . 88
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 88
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Contact information. . . . . . . . . . . . . . . . . . . . . 89
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2010.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 9 February 2010
Document identifier: P89LPC9151_61_71_2

Open as PDF

Similar pages: PHILIPS P89LPC954FA; PHILIPS P89LPC9107FDH; PHILIPS P89LPC913FDH; PHILIPS P89LPC9321FA; PHILIPS P89LPC932A1FDH; PHILIPS P89LPC902FD; Data Sheet; PHILIPS P89LPC938FDH; PHILIPS P89LPC9381FDH; PHILIPS P89LPC906; PHILIPS P89LPC952; PHILIPS P89LPC9107; PHILIPS P89LPC912FDH; PHILIPS P89LPC932; 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-er ...; ETC P89LPC931; PHILIPS P89LPC9408FBD; P89LPC933/934/935/936; 8-bit microcontrollers with two-clock 80C51 core 2 kB/4 kB/8 kB 3 V low-powe ...; PHILIPS P89LPC9401FBD; PHILIPS P89LPC932FDH; PHILIPS P89LPC930FDH