PI74FCT240T/241T/ 244T/540T/541T (25 ohmSeries) PI74FCT2240T/2241T/2244T/2541T 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Fast CMOS Octal Buffer/Line Drivers Product Features Product Description • PI74FCT240/241/244/540/541T and PI74FCT2240/2241/2244/ 2541T are pin compatible with bipolar FAST™ Series at a higher speed and lower power consumption 25Ω series resistor on all outputs (FCT2XXX only) • TTL input and output levels • Low ground bounce outputs • Extremely low static power • Hysteresis on all inputs • Industrial operating temperature range: 40°C to +85°C Packages available: – 20-pin 173 mil wide plastic TSSOP (L) – 20-pin 209 mil wide plastic SSOP (H) – 20-pin 300 mil wide plastic DIP (P) – 20-pin 150 mil wide plastic QSOP (Q) – 20-pin 150 mil wide plastic TQSOP (R) – 20-pin 300 mil wide plastic SOIC (S) • Device models available upon request Pericom Semiconductor’s PI74FCT series of logic circuits are produced in the Company’s advanced 0.6/0.8 micron CMOS technology, achieving industry leading speed grades. All PI74FCT2XXX devices have a built-in 25 ohm series resistor on all outputs to reduce noise because of reflections, thus eliminating the need for an external terminating resistor. The PI74FCT240T/241T/244T/540T/541T and P174FCT2240T/ 2241T/2244/2541T are 8-bit wide driver circuits, designed to be used in applications requiring high-speed and high-output drive. Ideal applications would include bus drivers, memory drivers, address drivers, and system clock drivers. The PI74FCT540T and PI74FCT541/2541T provide similar driver capabilities, but have their pins physically grouped by function. All inputs are located on one side of the package, while outputs are on the opposite side, allowing for a much simpler and denser board layout. Logic Block Diagrams PI74FCT241/2241T PI74FCT244/2244T PI74FCT240/2240T PI74FCT540T PI74FCT541/2541T OEA OEB 241 Only OEA OEA OEB OEB* D0 O0 D1 O1 D2 O2 D3 O3 OA2 D4 O4 OB2 DB2 D5 O5 OA3 DA3 OA3 D6 O6 DB3 OB3 DB3 D7 O7 DA0 OA0 DA0 OA0 OB0 DB0 OB0 DB0 DA1 OA1 DA1 OA1 OB1 DB1 OB1 DB1 DA2 OA2 DA2 OB2 DB2 DA3 OB3 *OEB for 241T, *OEB for 244T, 1 *Logic diagram shown for 540T. 541/2541T is the non-inverting option. PS2011B 12/11/00 PI74FCT240T/241T/244T/540T/541T (25 ohm Series) PI74FCT2240T/2241T/2244T/2541T Octal Buffer/Line Drivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Product Pin Description Pin Name OEA, OEB OEB(1) Dxx Oxx GND VCC Truth Table Description 3-State Output Enable Inputs (Active LOW) 3-State Output Enable Input (Active HIGH) Inputs Outputs Ground Power OEA L L H Inputs(1) OEB OEB(2) L H L H H L D L H X Outputs(1) 240 241 244 540 541 H L L H L L H H L H Z Z Z Z Z Note: 1. H = High Voltage Level, X = Don't Care, L = Low Voltage Level, Z = High Impedance 2. OEB for 241 only. PI74FCT240/2240T Product Pin Configuration OEA DA0 OB0 DA1 OB1 DA2 OB2 DA3 OB3 GND 1 20 2 19 3 20-Pin 18 H20 17 4 L20 16 5 P20 15 6 Q20 14 7 R20 13 8 S20 12 9 10 11 Vcc OEB OA0 DB0 OA1 DB1 OA2 DB2 OA3 DB3 PI74FCT241/2241/244/2244T Product Pin Configuration OEA DA0 OB0 DA1 OB1 DA2 OB2 DA3 OB3 GND 1 2 3 4 5 6 7 8 9 10 20-Pin H20 L20 P20 Q20 R20 S20 20 19 18 17 16 15 14 13 12 11 Vcc OEB OA0 DB0 OA1 DB1 OA2 DB2 OA3 DB3 *OEB for 241T, OEB for 244T PI74FCT540/541/2541T Product Pin Configuration OEA D0 D1 D2 D3 D4 D5 D6 D7 GND 1 2 3 4 5 6 7 8 9 10 20-Pin H20 L20 P20 Q20 R20 S20 20 19 18 17 16 15 14 13 12 11 Vcc OEB O0* O2* O2* O3* O4* O5* O6* O7* *Ox for 540T, Ox for 541T 2 PS2011B 12/11/00 PI74FCT240T/241T/244T/540T/541T (25 ohm Series) PI74FCT2240T/2241T/2244T/2541T Octal Buffer/Line Drivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ........................................................... –65°C to +150°C Ambient Temperature with Power Applied ........................... -40°C to +85°C Supply Voltage to Ground Potential (Inputs & Vcc Only) .... –0.5V to +7.0V Supply Voltage to Ground Potential (Outputs & D/O Only) .–0.5V to +7.0V DC Input Voltage ....................................................................–0.5V to +7.0V DC Output Current ............................................................................... 120mA Power Dissipation ................................................................................... 0.5W Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 5.0V ± 5%) Parameters Description Test Conditions(1) Min. Typ(2) Max. Units VOH Output HIGH Voltage VCC = Min., VIN = VIH or VIL IOH = –15.0mA 2.4 3.0 V VOL Output LOW Current VCC = Min., VIN = VIH or VIL IOL = 64mA 0.3 0.55 V VOL Output LOW Current VCC = Min., VIN = VIH or VIL IOL = 12mA (25ΩSeries) 0.3 0.50 V VIH Input HIGH Voltage Guaranteed Logic HIGH Level VIL Input LOW Voltage Guaranteed Logic LOW Level IIH Input HIGH Current VCC = Max. IIL Input LOW Current IOZH High Impedance IOZL Output Current VIK Clamp Diode Voltage VCC = Min., IIN = –18mA IOFF Power Down Disable VCC = GND, VOUT = 4.5V IOS Short Circuit Current (3) VH Input Hysteresis 2.0 V 0.8 V VIN = VCC 1 µA VCC = Max. VIN = GND –1 µA VCC = MAX. VOUT = 2.7V 1 µA VOUT = 0.5V –1 µA –0.7 –1.2 V — — 100 µA –60 –120 mA 200 mV VCC = Max. , VOUT = GND Capacitance (TA = 25°C, f = 1 MHz) Parameters(4) Description Test Conditions Typ Max. Units CIN Input Capacitance VIN = 0V 6 10 pF COUT Output Capacitance VOUT = 0V 8 12 pF Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at Vcc = 5.0V, +25°C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. This parameter is determined by device characterization but is not production tested. 3 PS2011B 12/11/00 PI74FCT240T/241T/244T/540T/541T (25 ohm Series) PI74FCT2240T/2241T/2244T/2541T Octal Buffer/Line Drivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Power Supply Characteristics Test Conditions(1) Parameters Description Min. Typ(2) Max. Units ICC Quiescent Power Supply Current VCC = Max. VIN = GND or VCC 0.1 500 µA ∆ICC Supply Current per Input @ TTL HIGH VCC = Max. VIN = 3.4V(3) 0.5 2.5 mA ICCD Supply Current per Input per MHz(4) VCC = Max., Outputs Open OEA = OEB = GND or OEA = GND, OEB = VCC One Bit Toggling 50% Duty Cycle VIN = VCC VIN = GND 0.15 0.25 mA/ MHz IC Total Power Supply Current(6) VCC = Max., Outputs Open fI = 10 MHZ 50% Duty Cycle OEA = OEB = GND or OEA = GND, OEB = VCC One Bit Toggling VIN = VCC VIN = GND 1.5 3.5(5) mA VIN = 3.4V VIN = GND 1.8 4.5(5) VIN = VCC VIN = GND 3.0 6.0(5) VIN = 3.4V VIN = GND 5.0 14.0(5) VCC = Max., Outputs Open fI = 2.5 MHZ 50% Duty Cycle OEA = OEB = GND or OEA = GND, OEB = VCC Eight Bits Toggling Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at Vcc = 5.0V, +25°C ambient. 3. Per TTL driven input (VIN = 3.4V); all other inputs at Vcc or GND. 4. This parameter is not directly testable, but is derived for use in Total Power Supply Calculations. 5. Values for these conditions are examples of the Icc formula. These limits are guaranteed but not tested. 6. IC = IQUIESCENT + IINPUTS + IDYNAMIC IC = ICC + ∆ICC DHNT + ICCD (fCP/2 + fINI) ICC = Quiescent Current ∆ICC = Power Supply Current for a TTL High Input (VIN = 3.4V) DH = Duty Cycle for TTL Inputs High NT = Number of TTL Inputs at DH ICCD = Dynamic Current Caused by an Input Transition Pair (HLH or LHL) fCP = Clock Frequency for Register Devices (Zero for Non-Register Devices) fI = Input Frequency NI = Number of Inputs at fI All currents are in milliamps and all frequencies are in megahertz. 4 PS2011B 12/11/00 PI74FCT240T/241T/244T/540T/541T (25 ohm Series) PI74FCT2240T/2241T/2244T/2541T Octal Buffer/Line Drivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 PI74FCT240/2240T Switching Characteristics over Operating Range Parameters Description tPLH tPHL tPZH tPZL tPHZ tPLZ Propagation Delay DN to ON Output Enable Time OEX to ON Output Disable Time(3) OEX to ON Conditions(1) CL = 50pF RL = 500Ω 240T/2240T Com. Min Max 240AT/2240AT 240CT/2240CT Com. Com. Min Max Min Max 240DT Com. Min Max Units 1.5 8.0 1.5 4.8 1.5 4.3 1.5 3.6 ns 1.5 10.0 1.5 6.2 1.5 5.8 1.5 4.8 ns 1.5 9.5 1.5 5.6 1.5 5.2 1.5 4.0 ns PI74FCT241/2241T Switching Characteristics over Operating Range Parameters Description tPLH tPHL tPZH tPZL tPHZ tPLZ Propagation Delay DN to ON Output Enable Time OEA/OEB to ON Output Disable Time(3) OEA/OEB to ON Conditions(1) CL = 50pF RL = 500Ω 241T/2241T Com. Min Max 241AT/2241AT 241CT/2241CT Com. Com. Min Max Min Max 241DT Com. Min Max Units 1.5 6.5 1.5 4.8 1.5 4.1 1.5 3.6 ns 1.5 8.0 1.5 6.2 1.5 5.8 1.5 4.8 ns 1.5 7.0 1.5 5.6 1.5 5.2 1.5 4.0 ns PI74FCT244/2244T Switching Characteristics over Operating Range Parameters Description Units tPLH tPHL tPZH tPZL tPHZ tPLZ Propagation Delay DN to ON Output Enable Time OEX to ON Output Disable Time(3) OEX to ON Conditions(1) CL = 50pF RL = 500Ω 244T/2244T Com. Min Max 244AT/2244AT 244CT/2244CT Com. Com. Min Max Min Max 244DT Com. Min Max 1.5 6.5 1.5 4.8 1.5 4.1 1.5 3.6 ns 1.5 8.0 1.5 6.2 1.5 5.8 1.5 4.8 ns 1.5 7.0 1.5 5.6 1.5 5.2 1.5 4.0 ns Notes: 1. See test circuit and wave forms. 2. Minimum limits are guaranteed but not tested on Propagation Delays. 3. This parameter is guaranteed but not production tested. 5 PS2011B 12/11/00 PI74FCT240T/241T/244T/540T/541T (25 ohm Series) PI74FCT2240T/2241T/2244T/2541T Octal Buffer/Line Drivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 PI74FCT540T Switching Characteristics over Operating Range Parameters Description tPLH tPHL tPZH tPZL tPHZ tPLZ Propagation Delay DN to ON Output Enable Time OEX to ON Output Disable Time(3) OEX to ON Conditions(1) CL = 50pF RL = 500Ω 540T Com. Min Max 540AT Com. Min Max 540CT Com. Min Max 540DT Com. Min Max Units 1.5 5.5 1.5 4.8 1.5 4.3 1.5 3.8 ns 1.5 10.0 1.5 6.2 1.5 5.8 1.5 5.2 ns 1.5 6.0 1.5 5.6 1.5 5.2 1.5 5.2 ns PI74FCT541/2541T Switching Characteristics over Operating Range Parameters Description tPLH tPHL tPZH tPZL tPHZ tPLZ Propagation Delay DN to ON Output Enable Time OEX to ON Output Disable Time(3) OEX to ON Conditions(1) CL = 50pF RL = 500Ω 541T/2541T Com. Min Max 541AT/2541AT 541CT/2541CT Com. Com. Min Max Min Max 541DT Com. Min Max Units 1.5 6.0 1.5 4.8 1.5 4.1 1.5 3.8 ns 1.5 9.5 1.5 6.2 1.5 5.8 1.5 5.2 ns 1.5 6.5 1.5 5.6 1.5 5.2 1.5 5.2 ns Notes: 1. See test circuit and wave forms. 2. Minimum limits are guaranteed but not tested on Propagation Delays. 3. This parameter is guaranteed but not production tested. Pericom Semiconductor Corporation 2380 Bering Drive • San Jose, CA 95131 • 1-800-435-2336 • Fax (408) 435-1100 • http://www.pericom.com 6 PS2011B 12/11/00