PM6675S High efficiency step-down controller with embedded 2 A LDO regulator Features ■ ■ Switching section – 4.5 V to 28 V input voltage range – 0.6 V, ±1 % voltage reference – Selectable 1.5 V fixed output voltage – Adjustable 0.6 V to 3.3 V output voltage – 1.237 V ±1 % reference voltage available – Very fast load transient response using constant on-time control loop – No RSENSE current sensing using low side MOSFETs' RDS(ON) – Negative current limit – Latched OVP and UVP – Soft-start internally fixed at 3 ms – Selectable pulse skipping at light load – Selectable No-Audible (33 kHz) pulse skip mode – Ceramic output capacitors supported – Output voltage ripple compensation – Output soft-end LDO regulator section – Adjustable 0.6 V to 3.3 V output voltage – Selectable ±1 Apk or ±2 Apk current limit – Dedicated power-good signal – Ceramic output capacitors supported – Output soft-end Applications ■ Notebook computers ■ Graphic cards ■ Embedded computers Table 1. VFQFPN-24 4x4 Description The PM6675S device consists of a single high efficiency step-down controller and an independent Low Drop-Out (LDO) linear regulator. The Constant On-Time (COT) architecture assures fast transient response supporting both electrolytic and ceramic output capacitors. An embedded integrator control loop compensates the DC voltage error due to the output ripple. A selectable low-consumption mode allows the highest efficiency over a wide range of load conditions. The low-noise mode sets the minimum switching frequency to 33 kHz for audio-sensitive applications. The LDO linear regulator can sink and source up to 2 Apk. Two fixed current limits (±1 A-±2 A) can be chosen. An active soft-end is independently performed on both the switching and the linear regulators outputs when disabled. Device summary Order codes Package PM6675S Packaging Tube VFQFPN-24 4x4 (exposed pad) PM6675STR February 2008 Tape and reel Rev 1 1/53 www.st.com Contents PM6675S Contents 1 Typical application circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2 Pin settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 2.1 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Electrical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3.1 Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3.2 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3.3 Recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5 Typical operating characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 6 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 7 Device description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 7.1 2/53 Switching section - constant on-time PWM controller . . . . . . . . . . . . . . . 20 7.1.1 Constant-On-Time architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 7.1.2 Output ripple compensation and loop stability . . . . . . . . . . . . . . . . . . . . 23 7.1.3 Pulse-skip and no-audible pulse-skip modes . . . . . . . . . . . . . . . . . . . . . 27 7.1.4 Mode-of-operation selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 7.1.5 Current sensing and current limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 7.1.6 POR, UVLO and Soft Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 7.1.7 Switching section power good signal . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 7.1.8 Switching section output discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 7.1.9 Gate drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 7.1.10 Reference voltage and bandgap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 7.1.11 Switching section OV and UV protections . . . . . . . . . . . . . . . . . . . . . . . 33 7.1.12 Device thermal protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 PM6675S Contents 7.2 8 LDO linear regulator section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 7.2.1 LDO section current limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 7.2.2 LDO section Soft-Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 7.2.3 LDO section power good signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 7.2.4 LDO section output discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 8.1 External components selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 8.1.1 Inductor selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 8.1.2 Input capacitor selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 8.1.3 Output capacitor selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 8.1.4 MOSFETs selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 8.1.5 Diode selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 8.1.6 VOUT current limit setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 8.1.7 All ceramic capacitors application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 9 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 10 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 3/53 Typical application circuit PM6675S 1 Typical application circuit Figure 1. Application circuit +5V R LP VBATT C IN3 C IN2 R1 C IN R2 23 LDO PG 22 VOSC VCC 8 B O O HGATE 21 T PHASE LIN PM6675S PM6675 LOUT CSNS 2 LFB 5 15 14 13 VREF COMP SWEN LEN SPG LGND PGND SGND 1 7 VSNS 11 C OUT2 SMPS PG 4/53 C BOOT L 20 VSMPS LGATE 17 4 LPG 24 VLDO 18 AVCC C IN4 10 VSEL 6 LILIM VLDOIN 12 NOSKIP 3 C BYP C OUT 19 16 R LIM 9 C INT PM6675S Pin settings 2 Pin settings 2.1 Connections CSNS PHASE HGATE BOOT LIN LOUT Pin connection (through top view) 19 24 1 18 LGND VCC LFB LGATE NOSKIP PGND PM6675 PM6675S LPG SPG SGND LEN AVCC SWEN 6 13 COMP VSEL VSNS VOSC LILIM 12 7 VREF Figure 2. 5/53 Pin settings 2.2 PM6675S Pin description Table 2. 6/53 Pin functions N° Pin Function 1 LGND 2 LFB 3 NOSKIP 4 LPG 5 SGND Ground reference for analog circuitry, control logic and VTTREF buffer. Connect together with the thermal pad and VTTGND to a low impedance ground plane. See the Application Note for details. 6 AVCC +5 V supply for internal logic. Connect to +5 V rail through a simple RC filtering network. 7 VREF High accuracy output voltage reference (1.237 V) for multilevel pins setting. It can deliver up to 50 µA. Connect a 100 nF capacitor between VREF and SGND in order to enhance noise rejection. 8 VOSC Frequency selection. Connect to the central tap of a resistor divider to set the desired switching frequency. The pin cannot be left floating. See Section 7: Device description on page 19 for details. 9 VSNS Switching section output remote sensing and discharge path during output soft-end. Connect as close as possible to the load via a low noise PCB trace. 10 VSEL Fixed output selector and feedback input for the switching controller. If VSEL pin voltage is higher than 4 V, the fixed 1.5 V output is selected. If VSEL pin voltage is lower than 4 V, it is used as negative input of the error amplifier. See Section 7.1.4: Mode-of-operation selection on page 30 for details. 11 COMP DC voltage error compensation input pin for the switching section. Refer to Section 7.1.4: Mode-of-operation selection on page 30 for more details. 12 LILIM Current limit selector for the LDO. Connect to SGND for ±1 A current limit or to +5 V for ±2 A current limit. 13 SWEN Switching controller enable. When tied to ground, the switching output is turned off and a soft-end is performed. 14 LEN Linear regulator enable. When tied to ground, the LDO output is turned off and a soft-end is performed. 15 SPG Switching section power good signal (open drain output). High when the switching regulator output voltage is within ±10 % of nominal value. 16 PGND Power ground for the switching section. 17 LGATE Low-side gate driver output. 18 VCC LDO power ground. Connect to the negative terminal of VTT output capacitor. LDO remote sensing. Connect as close as possible to the load via a low noise PCB trace. Pulse-Skip/No-Audible Pulse-Skip Modes selector. See Section 7.1.4: Mode-of-operation selection on page 30 LDO section power-good signal (open drain output). High when LDO output voltage is within ±10 % of nominal value. +5 V low-side gate driver supply. Bypass with a 100 nF capacitor to PGND. PM6675S Electrical data Table 2. Pin functions (continued) N° Pin Function 19 CSNS Current sense input for the switching section. This pin must be connected through a resistor to the drain of the synchronous rectifier (RDS(ON) sensing) to set the current limit threshold. 20 PHASE Switch node connection and return path for the high side gate driver. 21 HGATE High-Side Gate Driver Output 22 BOOT Bootstrap capacitor connection. Input for the supply voltage of the high-side gate driver. 23 LIN Linear Regulator Input. Bypass to LGND by a 10µF ceramic capacitor for noise rejection enhancement. 24 LOUT LDO linear regulator output. Bypass with a 20µF (2 x 10 µF MLCC) filter capacitor. 3 Electrical data 3.1 Maximum rating Table 3. Absolute maximum ratings (1) Symbol Parameter Value VAVCC AVCC to SGND -0.3 to 6 VVCC VCC to SGND -0.3 to 6 PGND, LGND to SGND VPHASE -0.3 to 0.3 HGATE and BOOT to PHASE -0.3 to 6 HGATE and BOOT to PGND -0.3 to 44 PHASE to SGND -0.3 to 38 LGATE to PGND -0.3 to VCC +0.3 CSNS, SPG, LEN, SWEN, LILIM, COMP, VSEL, VSNS, VOSC, VREF, NOSKIP to SGND -0.3 to VAVCC + 0.3 LPG,VREF, LOUT, LFB to SGND -0.3 to VAVCC + 0.3 LIN, LOUT, LPG, LIN to LGND -0.3 to VAVCC + 0.3 Maximum withstanding Voltage range test condition: CDF-AEC-Q100-002- “Human Body Model” acceptance criteria: “Normal Performance” Unit ± 1250 V V 1. Free air operating conditions unless otherwise specified. Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. Exposure to absolute maximum rated conditions for extended periods may affect device reliability. 7/53 Electrical data 3.2 PM6675S Thermal data Table 4. Thermal data Symbol 3.3 Parameter Value Unit 42 °C/W RthJA Thermal resistance junction to ambient TSTG Storage temperature range - 50 to 150 °C TA Operating ambient temperature range - 40 to 85 °C TJ Junction operating temperature range - 40 to 125 °C Recommended operating conditions Table 5. Recommended operating conditions Values Symbol Parameter Unit Min Max Input voltage range 4.5 28 VAVCC IC supply voltage 4.5 5.5 VVCC IC supply voltage 4.5 5.5 VIN 8/53 Typ V PM6675S Electrical characteristics 4 Electrical characteristics Table 6. Electrical characteristics TA = 0 °C to 85 °C, VCC = AVCC = +5 V, LIN = 1.5 V and LOUT = 0.6 V, if not otherwise specified (1) Values Symbol Parameter Test condition Unit Min Typ Max Supply section SWEN, LEN, VSEL and NOSKIP connected to AVCC, No load on LOUT output. IIN Operating current (Switching + LDO) ISW SWEN, VSEL and NOSKIP Operating current (Switching) connected to AVCC, LEN connected to SGND. 1 Shutdown operating current 10 ISHDN 2 mA SWEN and LEN tied to SGND. AVCC under voltage lockout upper threshold 4.1 4.25 µA 4.4 V UVLO AVCC under voltage lockout upper threshold 3.85 UVLO hysteresis 4.0 4.1 70 mV ON-time (SMPS) tON On-time duration VSEL low, NOSKIP low, VVSNS = 2V VOSC=300 mV 530 630 730 VOSC=500 mV 320 380 440 300 350 ns 1.237 1.249 V ns OFF-time (SMPS) tOFFMIN Minimum OFF-time Voltage reference Voltage accuracy 4.5 V< VIN < 25 V Load regulation -50 µA< IVREF < 50 µA Undervoltage Lockout Fault Threshold 1.224 -4 4 mV 800 9/53 Electrical characteristics Table 6. PM6675S Electrical characteristics (continued) TA = 0 °C to 85 °C, VCC = AVCC = +5 V, LIN = 1.5 V and LOUT = 0.6 V, if not otherwise specified (1) Values Symbol Parameter Test condition Unit Min Typ Max SMPS output SMPS fixed output voltage VOUT Feedback output voltage accuracy 1.5 VSEL connected to AVCC, NOSKIP tied to SGND, No Load -1.5 V 1.5 % 110 µA Current limit and zero crossing comparator ICSNS VZC,OFFS CSNS input bias current 90 Comparator offset -6 100 6 Positive current limit threshold VPGND - VCSNS 100 Fixed negative current limit threshold 110 Zero crossing comparator offset -11 mV -5 1 HGATE high state (pull-up) 2.0 3 HGATE low state (pull-down) 1.8 2.7 LGATE high state (pull-up) 1.4 2.1 LGATE low state (pull-down) 0.6 0.9 High and low side gate drivers HGATE driver on-resistance Ω LGATE driver on-resistance UVP/OVP protections and PGOOD signals OVP Over voltage threshold 112 115 118 UVP Under voltage threshold 67 70 73 SMPS upper threshold 107 110 113 SMPS lower threshold 86 90 93 LDO upper threshold 107 110 113 LDO lower threshold 86 90 93 % PGOOD IPG,LEAK SPG and LPG Leakage Current SPG and LPG forced to 5.5 V VPG,LOW SPG and LPG Low Level Voltage ILPG,SINK = ISPG,SINK = 4 mA 1 µA 150 250 mV 3 4 ms Soft-start section (SMPS) Soft-start ramp time (4 steps current limit) Soft-start current limit step 10/53 2 25 µA PM6675S Table 6. Electrical characteristics Electrical characteristics (continued) TA = 0 °C to 85 °C, VCC = AVCC = +5 V, LIN = 1.5 V and LOUT = 0.6 V, if not otherwise specified (1) Values Symbol Parameter Test condition Unit Min Typ Max Switching section discharge resistance 15 25 35 LDO section discharge resistance 15 25 35 Soft-end section Ω LDO section VLREF LDO reference voltage 600 LDO output accuracy respect -1 mA < ILDO < 1 mA to VREF -1 A < ILDO < 1 A LDO sink current limit LDO source current limit 20 -25 25 VLFB > VLREF , LILIM = 5 V -3 -2.3 -2 VLFB > VLREF, LILIM = 0 V -1.6 -1.3 -1 2 2.4 3 0.9 • VLREF < VLFB < VLREF, LILIM = 5V ILDO,CL -20 A 0.9 • VLREF < VLFB < VLREF, LILIM = 0V 1 1.3 1.6 VLFB < 0.9 • VLREF, LILIM = 5 V 1 1.3 1.6 VLFB < 0.9 • VLREF, LILIM = 0 V 0.5 0.8 1.1 1 10 LDO input bias current, ON LEN connected to AVCC, no load LDO input bias current, OFF LEN = 0 V, no load ILFB,BIAS LFB input bias current LEN connected to AVCC VLFB = 0.6 V -1 1 ILFB,LEAK LFB leakage current LEN = 0 V, VLFB = 0.6 V -1 1 ILIN,BIAS mV 1 µA 11/53 Electrical characteristics Table 6. PM6675S Electrical characteristics (continued) TA = 0 °C to 85 °C, VCC = AVCC = +5 V, LIN = 1.5 V and LOUT = 0.6 V, if not otherwise specified (1) Values Symbol Parameter Test condition Unit Min Typ Max Power management section Fixed mode VVTHVSEL VAVCC -0.7 VSEL pin thresholds VAVCC -1.3 Adjustable mode Forced-PWM mode VVTHNOSKIP NOSKIP pin thresholds No-audible mode VAVCC -0.8 VAVCC -1.5 1.0 Pulse-skip mode VVTHLEN, VVTHSWEN LEN, SWEN turn off level VVTHLILIM LILIM pin thresholds V 0.5 0.4 LEN, SWEN turn on level 1.6 ±2 A LDO current limit VAVCC -0.8 ±1 A LDO current limit 0.5 IIN,LEAK Logic input leakage current LEN, SWEN and LILIM = 5 V 10 IIN3,LEAK Multilevel input leakage current VSEL and NOSKIP = 5 V 10 IOSC,LEAK VOSC pin leakage current VOSC = 1 V 1 µA Thermal shutdown TSHDN Shutdown temperature (2) 150 1. TA = TJ. All parameters at operating temperature extremes are guaranteed by design and statistical analysis (not production tested) 2. Guaranteed by design. Not production tested. 12/53 °C PM6675S Typical operating characteristics 5 Typical operating characteristics Figure 3. VOUT efficiency vs load, 1.5 V, SW frequency = 400 kHz Figure 4. 100 100 SKIP @ 8V 90 SKIP @ 8V 90 80 SKIP @ 12V 80 SKIP @ 12V 70 SKIP @ 16V 70 SKIP @ 16V 60 No Aud. SKIP @ 8V 60 No A ud. SKIP @ 8V 50 No Aud. SKIP @ 12V 50 No A ud. SKIP @ 12V 40 No Aud. SKIP @ 16V 40 No A ud. SKIP @ 16V 30 PWM @ 8V 30 PWM @ 8V 20 PWM @ 12V 10 PWM @16V Efficiency [%] Efficiency [%] VOUT efficiency vs load, 1.25 V, SW frequency = 400 kHz 20 0.10 1.00 PWM @ 16V 0 0.01 0 0.01 PWM @ 12V 10 10.00 0.10 VOUT load regulation, 1.5 V, Vin = 12 V Figure 6. 1.54 VOUT load regulation, 1.25 V, Vin = 12 V 1.280 1.275 1.53 PWM Output Voltage [V] Output Voltage [V] 10.00 Output Current [A] Output Current [A] Figure 5. 1.00 No Aud. SKIP 1.52 SKIP 1.51 1.50 1.49 PWM 1.270 No Aud. SKIP 1.265 SKIP 1.260 1.255 1.250 1.245 1.48 0.01 0.10 1.00 1.240 0.01 10.00 0.10 Output Current [A] Figure 7. VOUT load regulation, 2.5 V, Vin = 12 V Figure 8. 10.00 LOUT load regulation, LOUT = 0.9 V, LIN = 1.5 V 0.94 2.55 0.93 2.54 PWM 2.53 No Aud. SKIP 2.52 SKIP 0.92 LOUT [V] Output Voltage [V] 2.56 2.51 2.50 0.91 0.90 0.89 0.88 2.49 2.48 0.01 1.00 Output Current [A] 0.87 -2.0 0.1 1 10 -1.5 -1.0 -0.5 0.0 0.5 1.0 1.5 2.0 Output Current [A] Output Current [A] 13/53 Typical operating characteristics Figure 9. PM6675S VOUT line regulation, 1.5 V, 0 A Figure 10. VOUT line regulation, 1.25 V, 0 A 1.285 1.535 1.530 SKIP @ 0A No Aud. SKIP @ 0A 1.525 PWM @ 0A 1.520 1.515 Output Voltage [V] Output Voltage [V] 1.540 1.510 1.280 SKIP @ 0A 1.275 No Aud. SKIP @ 0A 1.270 PWM @ 0A 1.265 1.260 0 10 20 0 30 10 Input Voltage [V] Figure 11. VOUT line regulation, 1.5 V 1.5160 1.5155 PWM @ 0A 1.5150 PWM @ 7A 1.5145 1.5140 1.5135 Output Voltage [V] Output Voltage [V] 1.2660 1.5165 1.5130 0 5 10 15 20 25 1.2655 1.2650 1.2645 PWM @ 0A 1.2640 PWM @ 7A 1.2635 1.2630 1.2625 30 0 5 10 Input Voltage [V] 15 20 25 30 Input Voltage [V] Figure 13. Switching frequency vs input voltage, 1.5 V Figure 14. Switching frequency vs input voltage, 1.25 V 600 600 550 550 500 450 PWM @ 0A 400 PWM @ 7A 350 fsw [kHz] 500 fsw [kHz] 30 Figure 12. VOUT line regulation, 1.25 V 1.5170 450 PWM @ 0A 400 PWM @ 7A 350 300 300 250 250 200 0 5 10 15 20 Input Voltage [V] 14/53 20 Input Voltage [V] 25 30 0 5 10 15 20 Input Voltage [V] 25 30 PM6675S Typical operating characteristics Figure 15. Switching frequency vs load - 1.5 V Figure 16. PWM waveforms 600 fsw [kHz] 500 400 300 Pulse SKIP 200 No Aud. SKIP 100 PWM 0 0.01 0.1 1 10 Output Current [A] Figure 17. No-audible pulse-skip waveforms Figure 18. Pulse-skip waveforms Figure 19. Power-up sequence VCC above UVLO Figure 20. VOUT soft-start, 1.5 V, heavy load 15/53 Typical operating characteristics PM6675S Figure 21. Switching section output soft-end Figure 22. LDO section output soft-end Figure 23. -1.8 A to 1.8 A LOUT load transient, 0.9 V Figure 24. -1 A to 1 A LOUT load transient, 0.9 V Figure 25. 0 A to 8 A VOUT load transient, PWM Figure 26. 8 A to 0 A VOUT load transient, PWM 16/53 PM6675S Typical operating characteristics Figure 27. 0 A to 5 A VOUT load transient, Pulse-Skip Figure 28. 5 A to 0 A VOUT load transient, Pulse-Skip Figure 29. Over-voltage protection, VOUT = 1.5 V Figure 30. Under-voltage protection, VOUT = 1.5 V 17/53 Block diagram 6 PM6675S Block diagram Figure 31. Functional and block diagram VREF VOSC Vr = 0.6V 1.236V Bandgap BOOT LFB Level shifter Ton HGATE 1-shot LIN PHASE Ton min 1-shot _ LOUT Anti Cross Conduction VCC Toff min 1-shot LILIM LGATE + PGND LDS LEN 0.6V Zero Crossing & Current Limit LGND _ Vr +10% VREF COMP + LPG CSNS + SWEN Vr +10% + _ gm + Vr -10% + - Vr SPG + - SGND UVP/OVP Vr Vr -10% AVCC SWEN UVLO LDS LDS LEN VSNS LILIM NOSKIP Thermal Shutdown LEN Table 7. 18/53 SDS CONTROL LOGIC SWEN adj fix VSEL Legend SWEN Switching controller enable LEN LDO regulator enable LDS LDO output discharge enable SDS Switching output discharge enable LILIM LDO regulator current limit PM6675S 7 Device description Device description The PM6675S combines a single high efficiency step-down controller and an independent Low Drop-Out (LDO) linear regulator in the same package. The switching controller section is a high-performance, pseudo-fixed frequency, ConstantOn-Time (COT) based regulator specifically designed for handling fast load transient over a wide range of input voltages. The switching section output can be easily set to a fixed 1.5 V voltage without additional components or adjusted in the 0.6 V to 3.3 V range using an external resistor divider. The Switching Mode Power Supply (SMPS) can handle different modes of operation in order to minimize noise or power consumption, depending on the application needs. Selectable lowconsumption and low-noise modes allow the highest efficiency and a 33 kHz minimum switching frequency respectively at light loads. A lossless current sensing scheme, based on the Low-Side MOSFET turn-on resistance, avoids the need for an external sensing resistor. The input of the LDO can be either the switching section output or a lower voltage rail in order to reduce the total power dissipation. Linear regulator stability is achieved by filtering its output with a ceramic capacitor (20 µF or greater). The LDO linear regulator can sink and source up to 2 Apk. Two fixed current limit (±1 A-±2 A) can be chosen. An active soft-end is independently performed on both the switching and the linear regulators outputs when disabled. 19/53 Device description 7.1 PM6675S Switching section - constant on-time PWM controller The PM6675S employes a pseudo-fixed frequency, Constant On-Time (COT) controller as the core of the switching section. It is well known that the COT controller uses a relatively simple algorithm and uses the ripple voltage derived across the output capacitor ESR to trigger the On-Time one-shot generator. In this way, the output capacitor ESR acts as a current sense resistor providing the appropriate ramp signal to the PWM comparator. Nearly constant switching frequency is achieved by the system loop in steady-state operating conditions by varying the On-Time duration, avoiding thus the need for a clock generator. The On-Time one shot duration is directly proportional to the output voltage, detected by theVSNS pin, and inversely proportional to the input voltage, detected by the the VOSC pin, as follows: Equation 1 TON = K OSC VSNS +τ VOSC where KOSC is a constant value (130 ns typ.) and τ is the internal propagation delay (40ns typ.). The one-shot generator directly drives the high-side MOSFET at the beginning of each switching cycle allowing the inductor current to increase; after the On-Time has expired, an Off-Time phase, in which the low-side MOSFET is turned on, follows. The OffTime duration is solely determined by the output voltage: when lower than the set value (i.e. the voltage at VSNS pin is lower than the internal reference VR = 0.6 V), the synchronous rectifier is turned off and a new cycle begins (Figure 32). Figure 32. Inductor current and output voltage in steady state conditions Inductor current Output voltage Vreg Ton 20/53 Toff t PM6675S Device description The duty-cycle of the buck converter is, in steady-state conditions, given by Equation 2 V OUT D = -------------V IN The switching frequency is thus calculated as Equation 3 fSW VOUT α VIN D 1 = = = OSC ⋅ VSNS TON α OUT K OSC K OSC VOSC where Equation 4a V OSC α OSC = -------------V IN Equation 4b V SNS α OUT = -------------V OUT Referring to the typical application schematic (figures on cover page and Figure 33), the final expression is then: Equation 5 fSW = α OSC R2 1 = ⋅ K OSC R1 + R 2 K OSC Even if the switching frequency is theoretically independent from battery and output voltages, parasitic parameters involved in the power path (like MOSFET on-resistance and inductor DCR) introduce voltage drops responsible for a slight dependence on load current. In addition, the internal delay is due to a small dependence on input voltage. The PM6675S switching frequency can be set by an external divider connected to the VOSC pin. 21/53 Device description PM6675S Figure 33. Switching frequency selection and VOSC pin VIN PM6675 PM6675S R1 VOSC R2 The voltage seen at this pin must be greater than 0.8 V and lower than 2 V in order to ensure the system linearity. 7.1.1 Constant-On-Time architecture Figure 34 shows the simplified block diagram of the Constant-On-Time controller. The switching regulator of the PM6675S controls a one-shot generator that turns on the high-side MOSFET when the following conditions are simultaneously satisfied: the PWM comparator is high (i.e. output voltage is lower than Vr = 0.6 V), the synchronous rectifier current is below the current limit threshold and the minimum off-time has expired. A minimum Off-Time contraint (300ns typ.) is introduced to assure the boot capacitor charge and allow inductor valley current sensing on low-side MOSFET. A minimum On-Time is also introduced to assure the start-up switching sequence. Once the On-Time has timed out, the high side switch is turned off, while the synchronous rectifier is ignited according to the anti-cross conduction management circuitry. When the output voltage reaches the valley limit (determined by internal reference Vr = 0.6 V), the low-side MOSFET is turned off according to the anti-cross conduction logic once again, and a new cycle begins. 22/53 PM6675S Device description Figure 34. Switching section simplified block diagram VOSC CSNS BOOT VOSC Positive Current Limit comparator ToffToff-min + Level shifter - 100uA PHASE + S Q - COMP PWM Comparator R gm + - Anti crossconduction circuitry Q - + + TonTon-min 0.6V 2.5V 500mV VCC VSEL<4V VSEL + - Ton 2.5V S VSNS S Q VOSC LS driver Q VSNS Min fsw counter R Q 0.6V VBG bandgap 1.236V + ZeroZero-crossing Comparator _ LGATE PGND R PULSE - SKIP SGND 7.1.2 HGATE 1-Shot generator VBG Integrator HS driver VREF Output ripple compensation and loop stability The loop is closed connecting the center tap of the output divider (internally, when the fixed output voltage is chosen, or externally, using the VSEL pin in the adjustable output voltage mode). The feedback node is the negative input of the error comparator, while the positive input is internally connected to the reference voltage (Vr = 0.6 V). When the feedback voltage becomes lower than the reference voltage, the PWM comparator goes to high and sets the control logic, turning on the high-side MOSFET. After the On-Time (calculated as previously described), the system releases the high-side MOSFET and turns on the synchronous rectifier. The voltage drop along ground and supply PCB paths, used to connect the output capacitor to the load, is a source of DC error. Furthermore the system regulates the output voltage valley, not the average, as shown in Figure 37. Thus, the voltage ripple on the output capacitor is an additional source of DC error. To compensate this error, an integrative network is introduced in the control loop, by connecting the output voltage to the COMP pin through a capacitor (CINT) as shown in Figure 35. 23/53 Device description PM6675S Figure 35. Circuitry for output ripple compensation COMP PIN VOLTAGE ∆V Vr VREF t COMP I=gm(V1-Vr) + - OUTPUT VOLTAGE PWM Comparator CFILT gm ∆V CINT RINT t + VCINT Vr RFb1 V1 RFb2 ESR VSNS COUT The additional capacitor is used to reduce the voltage on the COMP pin when higher than 300 mVpp and is unnecessary for most of applications. The trans conductance amplifier (gm) generates a current, proportional to the DC error, used to charge the CINT capacitor. The voltage across the CINT capacitor feeds the negative input of the PWM comparator, forcing the loop to compensate the total static error. An internal voltage clamp forces the COMP pin voltage range to ±150 mV respect to VREF. This is useful to avoid or smooth output voltage overshoot during a load transient. When the Pulse-Skip Mode is entered, the clamping range is automatically reduced to 60 mV in order to enhance the recovering capability. If the ripple amplitude is larger than 150 mV, an additional capacitor CFILT can be connected between the COMP pin and ground to reduce ripple amplitude, otherwise the integrator will operate out of its linearity range. This capacitor is unnecessary for most of applications and can be omitted. The design of the external feedback network depends on the output voltage ripple. If the ripple is higher than approximately 20 mV, the correct CINT capacitor is usually enough to keep the loop stable. The stability of the system depends firstly on the output capacitor zero frequency. The following condition must be satisfied: Equation 6 fSW > k ⋅ fZout = k 2π ⋅ C out ⋅ ESR where k is a fixed design parameter (k > 3). It determinates the minimum integrator capacitor value: 24/53 PM6675S Device description Equation 7 CINT > gm Vr ⎛f ⎞ Vout 2π ⋅ ⎜ SW − fZout ⎟ k ⎝ ⎠ ⋅ where gm = 50 µs is the integrator trans conductance. If the ripple on the COMP pin is greater than 150 mV, the auxiliary capacitor CFILT can be added. If q is the desired attenuation factor of the output ripple, CFILT is given by: Equation 8 CFILT = CINT ⋅ (1 − q) q In order to reduce the noise on the COMP pin, it is possible to add a resistor RINT that, together with CINT and CFILT, becomes a low pass filter. The cutoff frequency fCUT must be much greater (10 or more times) than the switching frequency: Equation 9 RINT = 2π ⋅ fCUT 1 CINT ⋅ CFILT ⋅ CINT + CFILT If the ripple is very small (lower than approximately 20mV), a different compensation network, called "Virtual-ESR" Network, is needed. This additional circuit generates a triangular ripple that is added to the output voltage ripple at the input of the integrator. The complete control scheme is shown in Figure 36. 25/53 Device description PM6675S Figure 36. "Virtual-ESR" network COMP PIN VOLTAGE T NODE VOLTAGE ∆V2 VREF ∆V1 t VREF t COMP I=gm(V1-Vr) - PWM Comparator RINT CINT CFILT gm R Vr C VSNS OUTPUT VOLTAGE ∆V + - T R1 + RFb1 V1 RFb2 ESR COUT t The ripple on the COMP pin is the sum of the output voltage ripple and the triangular ripple generated by the Virtual-ESR Network. In fact the Virtual-ESR Network behaves like a another equivalent series resistor RVESR. A good trade-off is to design the network in order to achieve an RVESR given by: Equation 10 R VESR = VRIPPLE − ESR ∆IL where ∆IL is the inductor current ripple and VRIPPLE is the total ripple at the T node, chosen greater than approximately 20 mV. The new closed-loop gain depends on CINT. In order to ensure stability it must be verified that: Equation 11 CINT > gm Vr ⋅ 2π ⋅ fZ Vout where: Equation 12 fZ = and: 26/53 1 2π ⋅ C out ⋅ R TOT PM6675S Device description Equation 13 RTOT = ESR + RVESR Moreover, the CINT capacitor must meet the following condition: Equation 14 fSW > k ⋅ fZ = k 2π ⋅ C out ⋅ R TOT where RTOT is the sum of the ESR of the output capacitor and the equivalent ESR given by the Virtual-ESR Network (RVESR). The k parameter must be greater than unity (k > 3) and determines the minimum integrator capacitor value CINT: Equation 15 CINT > gm Vr ⋅ ⎛ fSW ⎞ Vout 2π ⋅ ⎜ − fZ ⎟ ⎝ k ⎠ The capacitor of the Virtual-ESR Network, C, is chosen as follow Equation 16 C > 5 ⋅ CINT and R is calculated to provide the desired triangular ripple voltage: Equation 17 R= L R VESR ⋅ C Finally the R1 resistor is calculated according to Equation 18: Equation 18 ⎛ 1 ⎞ ⎟⎟ R ⋅ ⎜⎜ f π ⋅ Z ⋅C⎠ ⎝ R1 = 1 R− π ⋅ fZ ⋅ C 27/53 Device description 7.1.3 PM6675S Pulse-skip and no-audible pulse-skip modes High efficiency at light load conditions is achieved by PM6675S by entering the Pulse-Skip Mode (if enabled). At light load conditions the zero-crossing comparator truncates the lowside switch On-Time as soon as the inductor current becomes negative; in this way the comparator determines the On-Time duration instead of the output ripple. (see Figure 37). Figure 37. Inductor current and output voltage at light load with Pulse-Skip Inductor current Output voltage Vreg TON TOFF t TIDLE As a consequence, the output capacitor is left floating and its discharge depends solely on the current drained from the load. When the output ripple on the pin COMP falls under the reference, a new shot is triggered and the next cycle begins. The Pulse-Skip mode is naturally obtained enabling the zero-crossing comparator and automatically takes part in the COT algorithm when the inductor current is about half the ripple current amount, i.e. migrating from continuous conduction mode (C.C.M.) to discontinuous conduction mode (D.C.M.). The output current threshold related to the transition between PWM Mode and Pulse-Skip Mode can be approximately calculated as: Equation 19 ILOAD (PWM2Skip) = VIN − VOUT ⋅ TON 2 ⋅L At higher loads, the inductor current never crosses the zero and the device works in pure PWM mode with a switching frequency around the nominal value. A physiological consequence of Pulse-Skip Mode is a more noisy and asynchronous (than normal conditions) output, mainly due to very low load. If the Pulse-Skip is not compatible with the application, the PM6675S allows the user to choose between forced-PWM and NoAudible Pulse-Skip alternative modes (see Section 7.1.4: Mode-of-operation selection on page 30 for details). 28/53 PM6675S Device description No-audible pulse-skip mode Some audio-noise sensitive applications cannot accept the switching frequency to enter the audible range as it is possible in Pulse-Skip mode with very light loads. For this reason, the PM6675S implements an additional feature to maintain a minimum switching frequency of 33kHz despite a slight efficiency loss. At very light load conditions, if any switching cycle has taken place within 30µs (typ.) since the last one (because of the output voltage is still higher than the reference), a No-Audible Pulse-Skip cycle begins. The low-side MOSFET is turned on and the output is driven to fall until the reference point has been crossed. Then, the highside switch is turned on for a TON period and, once it has expired, the synchronous rectifier is enabled until the inductor current reaches the zero-crossing threshold (see Figure 38). Figure 38. Inductor current and output voltage at light load with non-audible pulse-skip Inductor current Output voltage Vreg TMAX TON TOFF TIDLE t For frequencies higher than 33 kHz (due to heavier loads) the device works in the same way as in Pulse-Skip mode. It is important to notice that in both Pulse-Skip and No-Audible Pulse-Skip modes, the switching frequency changes not only with the load but also with the input voltage. 29/53 Device description 7.1.4 PM6675S Mode-of-operation selection Figure 39. VSEL and NOSKIP multifunction pin configurations VOUT +5V R9 R8 PM6675 PM6675S VSEL VREF NOSKIP The PM6675S has been designed to satisfy the widest range of applications. The device is provided with some multilevel pins which allow the user to choose the appropriate configuration. The VSEL pin is used to firstly decide between fixed preset or adjustable (user defined) output voltages. When the VSEL pin is connected to +5 V, the PM6675S sets the switching section output voltage to 1.5 V without the need of an external divider. Applications requiring different output voltages can be managed by PM6675S simply setting the adjustable mode. Consider that if the VSEL pin voltage is higher than 4 V, the fixed output mode is selected. When connecting an external divider to the VSEL pin, it is used as negative input of the error amplifier and the output voltage is given by expression (20). Equation 20 VOUTADJ = 0.6 ⋅ R8 + R9 R8 The output voltage can be set in the range from 0.6 V to 3.3 V. The NOSKIP is the power saving algorithm selector: if tied to +5 V, the forced-PWM (fixed frequency) control is performed. If grounded or connected to VREF pin (1.237 V reference voltage), the Pulse-Skip or Non-Audible Pulse-Skip Modes are respectively selected. 30/53 PM6675S Device description Table 8. Mode-of-operation settings summary VSEL NOSKIP VOUT VNOSKIP > 4.2 V VVSEL > 4.3 V VVSEL < 3.7 V Forced-PWM 1V <VNOSKIP < 3.5 V 1.5 V Non-audible pulse-skip < 0.5 V Pulse-skip VNOSKIP > 4.2 V Forced-PWM 1V <VNOSKIP < 3.5 V ADJ VNOSKIP < 0.5 V 7.1.5 Operating mode Non-audible pulse-skip Pulse-skip Current sensing and current limit The PM6675S switching controller uses a valley current sensing algorithm to properly handle the current limit protection and the inductor current zero-crossing information. The current is detected during the conduction time of the low-side MOSFET. The current sensing element is the on-resistance of the low-side switch. The sensing scheme is visible in Figure 40. Figure 40. Current sensing scheme VIN PM6675S PM6675 HGATE VOUT PHASE CSNS 100µA·RILIM IVALLEY·RDSon LGATE PGND An internal 100 µA current source is connected to CSNS pin that is also the non-inverting input of the positive current limit comparator. When the voltage drop developed across the sensing parameter equals the voltage drop across the programming resistor RILIM, the controller skips subsequent cycles until the overcurrent condition is detected or the output UV protection latches off the device (see Section 7.1.11: Switching section OV and UV protections on page 34 ). Referring to Figure 40, the RDS(on) sensing technique allows high efficiency performance without the need for an external sensing resistor. The on-resistance of the MOSFET is affected by temperature drift and nominal value spread of the parameter itself; this must be considered during the RILIM setting resistor design. 31/53 Device description PM6675S It must be taken into account that the current limit circuit actually regulates the inductor valley current. This means that RILIM must be calculated to set a limit threshold given by the maximum DC output current plus half of the inductor ripple current: Equation 21 ICL = 100µA ⋅ RILIM RDSon The PM6675S provides also a fixed negative current limit to prevent excessive reverse inductor current when the switching section sinks current from the load in forced-PWM (3rd quadrant working conditions). This negative current limit threshold is measured between PHASE and PGND pins, comparing the drop magnitude on PHASE pin with an internal 110 mV fixed threshold. 7.1.6 POR, UVLO and soft-start The PM6675S automatically performs an internal startup sequence during the rising phase of the analog supply of the device (AVCC). The switching controller remains in a stand-by state until AVCC crosses the upper UVLO threshold (4.25 V typ.), keeping active the internal discharge MOSFETs (only if AVCC > 1V). The soft-start allows a gradual increase of the internal current limit threshold during startup reducing the input/output surge currents. At the beginning of start-up, the PM6675S current limit is set to 25 % of nominal value and the Under Voltage Protection is disabled. Then, the current limit threshold is sequentially brought to 100 % in four steps of approximately 750 µs (Figure 41). Figure 41. Soft-start waveforms Switching output Current limit threshold SWEN Time After a fixed 3ms total time, the soft-start finishes and UVP is released: if the output voltage doesn't reach the under voltage threshold within soft-start duration, the UVP condition is detected and the device performs a soft-end and latches off. Depending on the load conditions, the inductor current may or may not reach the nominal value of the current limit during the soft-start (Figure 42 shows two examples). 32/53 PM6675S Device description Figure 42. Soft-start at heavy load (a) and short-circuit (b) conditions, Pulse-Skip enabled (a) 7.1.7 (b) Switching section power good signal The SPG pin is an open drain output used to monitor output voltage through VSNS (in fixed output voltage mode) or VSEL (in adjustable output voltage mode) pins and is enabled after the soft-start timer has expired. The SPG signal is held low if the output voltage drops 10% below or rises 10 % above the nominal regulated value. The SPG output can sink current up to 4 mA. 7.1.8 Switching section output discharge Active soft-end of the output occurs when the SWEN (SWitching ENable) is forced low. When the switching section is turned off, an internal 25 Ω resistor discharges the output through the VSNS pin. Figure 43. Switching section soft-end VOUT Resistive Discharge SWEN 33/53 Device description 7.1.9 PM6675S Gate drivers The integrated high-current gate drivers allow using different power MOSFETs. The highside driver uses a bootstrap circuit which is supplied by the +5 V rail. The BOOT and PHASE pins work respectively as supply and return path for the high-side driver, while the low-side driver is directly fed through VCC and PGND pins. An important feature of the PM6675S gate drivers is the Adaptive Anti-Cross-Conduction circuitry, which prevents high-side and low-side MOSFETs from being turned on at the same time. When the high-side MOSFET is turned off, the voltage at the PHASE node begins to fall. The low-side MOSFET is turned on only when the voltage at the PHASE node reaches an internal threshold (2.5 V typ.). Similarly, when the low-side MOSFET is turned off, the high-side one remains off until the LGATE pin voltage is above 1 V. The power dissipation of the drivers is a function of the total gate charge of the external power MOSFETs and the switching frequency, as shown in the following equation: Equation 22 PD (driver ) = VDRV ⋅ Q g ⋅ fSW The low-side driver has been designed to have a low-resistance pull-down transistor (0.6 Ω typ.) in order to prevent undesired start-up of the low-side MOSFET due to the Miller effect. 7.1.10 Reference voltage and bandgap The 1.237 V internal bandgap reference has a granted accuracy of ±1 % over the 0 °C to 85 °C temperature range. The VREF pin is a buffered replica of the bandgap voltage. It can supply up to ±100 µA and is suitable to set the intermediate level of NOSKIP multifunction pin. A 100 nF (min.) bypass capacitor toward SGND is required to enhance noise rejection. If VREF falls below 0.8 V (typ.), the system detects a fault condition and all the circuitry is turned off. An internal divider derives a 0.6 V ± 1 % voltage (Vr) from the bandgap. This voltage is used as reference for both the switching and the linear sections. The Over-Voltage Protection, the Under-Voltage Protection and the power-good signals are also referred to Vr. 7.1.11 Switching section OV and UV protections When the switching output voltage is about 115 % of its nominal value, a latched OverVoltage Protection (OVP) occurs. In this case the synchronous rectifier immediately turns on while the high-side MOSFET turns off. The output capacitor is rapidly discharged and the load is preserved from being damaged. The OVP is also active during the soft-start. Once an OVP has taken part, a toggle on SWEN pin or a Power-On-Reset is necessary to exit from the latched state. When the switching output voltage is below 70 % of its nominal value, a latched UnderVoltage Protection occurs. This event causes the switching section to be immediately disabled and both switches to be opened. The controller performs a soft-end and the output is eventually kept to ground, turning the low side MOSFET on when the voltage is lower than 400 mV. The Under-Voltage Protection circuit is enabled only at the end of the soft-start. Once an UVP has taken part, a toggle on SWEN pin or a Power-On-Reset is necessary to clear the fault state and restart the section. 34/53 PM6675S 7.1.12 Device description Device thermal protection The internal control circuitry of the PM6675S self-monitors the junction temperature and turns all outputs off when the 150 °C limit has been overrun. This event causes the switching section to be immediately disabled and both switches to be opened. The controller performs a soft-end and both the outputs are eventually kept to ground, then the low side MOSFET is turned on when the voltage of the switching section is lower than 400 mV. The thermal fault is a latched protection and, in normal operating conditions it is restored by a Power-On Reset or toggling SWEN and LEN pins at the same time. Table 9. Switching section OV, UV and OT Faults management Fault Action Over voltage VOUT > 115 % of the LGATE pin is forced high and the device latches off. nominal value Exit by a Power-On Reset or toggling SWEN Under voltage VOUT < 70 % of the nominal value LGATE pin is forced high after the soft-end, then the device latches off. Exit by a Power-On Reset or toggling SWEN. TJ > +150 °C LGATE pin is forced high after the soft-end, then the device latches off. Exit by a Power-On Reset or toggling SWEN and LEN after 15°C temperature drop. Junction over temperature 7.2 Conditions LDO linear regulator section The independent Low-Drop-Out (LDO) linear regulator has been designed to sink and source up to 2 A peak current and 1 A continuously. The LDO output voltage can be adjusted in the range 0.6 V to 3.3 V simply connecting a resistor divider as shown in Figure 44. Equation 23 VLDO ADJ = 0.6 ⋅ R19 + R20 R20 Figure 44. LDO output voltage selection PM6675 PM6675S VLOUT LOUT Cc COUT R19 LFB R20 LGND 35/53 Device description PM6675S A compensation capacitor Cc must be added to adjust the dynamic response of the loop. The value of Cc is calculated according to the desired bandwidth of the LDO regulator and depends on the value of the feedback resistors. In most of applications the pole due to the compensation capacitor is placed at 100-200 kHz (equation 24). Equation 24 fp = 1 = 200kHz 2π(R19 ⊕ R20) ⋅ C C The LIN input can be connected to the switching section output for compact solutions or to a lower supply, if available in the system, in order to reduce the power dissipation of the LDO. A minimum output capacitance of 20 µF (2x10 µF MLCC capacitors) is enough to assure stability and fast load transient response. 7.2.1 LDO section current limit The LDO regulator can handle up to ±2 Apk, depending on the LDO input voltage and the LILIM pin setting. The output current is limited to ±1 A or ±2 A if the LILIM pin is connected to SGND or AVCC respectively (Figure 45). Figure 45. LDO current limit setting +5V PM6675 PM6675S ±2A CL ±1A CL LILIM The maximum current that the LDO can source depends also on the input and output voltages. Due to the high side MOSFET of the output stage, the LDO cannot source the limit current at high output voltages. In Figure 46 it is shown the maximum current that the LDO can source as function of the input and output voltages. For output voltages higher than 2 V, the maximum output current is limited as reported. 36/53 PM6675S Device description Figure 46. Maximum LDO source able output current vs input voltage 2.2 ILOUT [A] 2.0 VOUT=1.05V 1.8 VOUT=1.2V 1.6 VOUT=1.5V 1.4 1.2 1.0 VOUT=1.8V VOUT=2.0V VOUT=2.2V VOUT=2.5V VOUT=3.3V 0.8 0.6 0.4 0.2 0.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 VLIN [V] 7.2.2 LDO section soft-start The LDO section soft-start is performed by clamping the current limit. During startup, the LDO current limit voltage is set to 1A and the output voltage increases linearly. When the output voltage rises above 90 % of the nominal value, the current limit is released to 2 A according to the LILIM pin setting. At the end of the ramp-up phase of the soft-start, the LPG signal is masked for about 100 µs in order to ignore dynamic overshoot on the feedback pin. 7.2.3 LDO section power good signal The LPG pin is an open drain output used to monitor the LDO output voltage through LFB pin. The LPG signal is held low if the output voltage drops 10 % below or rises 10 % above the nominal regulated value. The LPG output can sink current up to 4 mA. 7.2.4 LDO section output discharge Active soft-end of the LDO output occurs when the LEN (Linear ENable) is forced low. When the LDO section is turned off, an internal 25 Ω resistor, directly connected to the LOUT pin, discharges the output. Figure 47. LDO section soft-end VLDO Resistive Discharge LEN 37/53 Application information 8 PM6675S Application information The purpose of this chapter is showing the design procedure of the switching section. The design starts from three main specifications: ● The input voltage range, provided by the battery or the external supply. The two extreme values (VINMAX and VINmin ) are important for the design. ● The maximum load current, indicated with ILOAD,MAX. ● The maximum allowed output voltage ripple VRIPPLE,MAX. It's also possible that specific designs should involve other specifications. The following paragraphs will guide the user into a step-by-step design. 8.1 External components selection The PM6675S uses a pseudo-fixed frequency, Constant On-Time (COT) controller as the core of the switching section. The switching frequency can be set by connecting an external divider to the VOSC pin. The voltage seen at this pin must be greater than 0.8V and lower than 2 V in order to ensure system linearity. Nearly constant switching frequency is achieved by the system loop in steady-state operating conditions by varying the On-Time duration, avoiding thus the need for a clock generator. The On-Time one shot duration is directly proportional to the output voltage, sensed at VSNS pin, and inversely proportional to the input voltage, sensed at the VOSC pin, as follows: Equation 25 TON = K OSC VSNS +τ VOSC where KOSC is a constant value (130 ns typ.) and τ is the internal propagation delay (40 ns typ.). The duty cycle of the buck converter is, in under steady state conditions, given by Equation 26 D= VOUT VIN The switching frequency is thus calculated as Equation 27 fSW 38/53 VOUT α VIN 1 D = = = OSC ⋅ VSNS TON α OUT K OSC K OSC ⋅ VOSC PM6675S Application information where Equation 28a α OSC = VOSC VIN α OUT = VSNS VOUT Equation 28b Referring to the typical application schematic (figure in cover page and Figure 33), the final expression is then: Equation 29 fSW = α OSC R2 1 = ⋅ K OSC R1 + R 2 K OSC The switching frequency directly affects two parameters: ● Inductor size: greater frequencies mean smaller inductances. In notebook applications, real estate solutions (i.e. low-profile power inductors) are mandatory also with high saturation and r.m.s. currents. ● Efficiency: switching losses are proportional to the frequency. Generally, higher frequencies imply lower efficiency. Even if the switching frequency is theoretically independent from battery and output voltages, parasitic parameters involved in power path (like MOSFETs on-resistance and inductor DCR) introduce voltage drops responsible for a slight dependence on load current. In addition, the internal delay is cause of a light dependence from input voltage. Table 10. Typical values for switching frequency selection R1 (kΩ) R2 (kΩ) Approx switching frequency (kHz) 330 11 250 330 13 300 330 15 350 330 18 400 330 20 450 330 22 500 39/53 Application information 8.1.1 PM6675S Inductor selection Once the switching frequency has been defined, the inductance value depends on the desired inductor ripple current. Low inductance value means great ripple current that brings poor efficiency and great output noise. On the other hand a great current ripple is desirable for fast transient response when a load step is applied. High inductance brings to good efficiency but the transient response is critical, especially if VINmin - VOUT is little. Moreover a minimum output ripple voltage is necessary to assure system stability and jitter-free operations (see Section 8.1.3: Output capacitor selection on page 42). The product of the output capacitor ESR multiplied by the inductor ripple current must be taken in consideration. A good trade-off between the transient response time, the efficiency, the cost and the size is choosing the inductance value in order to maintain the inductor ripple current between 20 % and 50 % (usually 40 %) of the maximum output current. The maximum inductor ripple current, ∆IL,MAX , occurs at the maximum input voltage. Given these considerations, the inductance value can be calculated using the following expression: Equation 30 L= VIN − VOUT VOUT ⋅ fsw ⋅ ∆IL VIN where fSW is the switching frequency, VIN is the input voltage, VOUT is the output voltage and ∆IL is the inductor ripple current. Once the inductor value is determined, the inductor ripple current is then recalculated: Equation 31 ∆IL,MAX = VIN,MAX − VOUT fsw ⋅ L ⋅ VOUT VIN,MAX The next step is the calculation of the maximum r.m.s. inductor current: Equation 32 IL,RMS = (ILOAD,MAX )2 + (∆IL,MAX )2 12 The inductor must have an r.m.s. current greater than IL,RMS in order to assure thermal stability. Then the calculation of the maximum inductor peak current follows: Equation 33 IL,PEAK = ILOAD,MAX + ∆IL,MAX 2 IL,PEAK is important when choosing the inductor, in term of its saturation current. 40/53 PM6675S Application information The saturation current of the inductor should be greater than IL,PEAK as well as for case of hard saturation core inductors. Using soft-ferrite cores is possible (but not advisable) to push the inductor working near its saturation current. In Table 11 some inductors suitable for notebook applications are listed. Table 11. Evaluated inductors (@fsw = 400 kHz) Manufacturer Series Inductance (µH) +40 °C RMS current (A) -30 % saturation current (A) COILCRAFT MLC1538-102 1 13.4 21.0 COILCRAFT MLC1240-901 0.9 12.4 24.5 COILCRAFT MVR1261C-112 1.1 20 20 WURTH 7443552100 1 16 20 COILTRONICS HC8-1R2 1.2 16.0 25.4 In Pulse-Skip Mode, low inductance values produce a better efficiency versus load curve, while higher values result in higher full-load efficiency because of the smaller current ripple. 8.1.2 Input capacitor selection In a buck topology converter the current that flows through the input capacitor is pulsed and with zero average value. The RMS input current can be calculated as follows: Equation 34 2 ICinRMS = ILOAD ⋅ D ⋅ (1 − D) + 1 D ⋅ (∆IL )2 12 Neglecting the second term, the equation 10 is reduced to: Equation 35 ICinRMS = ILOAD D ⋅ (1 − D) The losses due to the input capacitor are thus maximized when the duty-cycle is 0.5: Equation 36 Ploss = ESR Cin ⋅ ICinRMS (max)2 = ESR Cin ⋅ (0.5 ⋅ ILOAD (max))2 The input capacitor should be selected with a RMS rated current higher than ICINRMS(max). Tantalum capacitors are good in terms of low ESR and small size, but they occasionally can burn out if subjected to very high current during operation. Multi-Layers-Ceramic-Capacitors (MLCC) have usually a higher RMS current rating with smaller size and they remain the best choice. The drawback is their quite high cost. 41/53 Application information PM6675S It must be taken into account that in some MLCC the capacitance decreases when the operating voltage is near the rated voltage. In Table 12 some MLCC suitable for most of applications are listed. Table 12. Evaluated MLCC for input filtering Manufacturer 8.1.3 Capacitance (µF) Rated voltage (V) Series Maximum Irms @100 kHz (A) TAIYO YUDEN UMK325BJ106KM-T 10 50 2 TAIYO YUDEN GMK316F106ZL-T 10 35 2.2 TAIYO YUDEN GMK325F106ZH-T 10 35 2.2 TAIYO YUDEN GMK325BJ106KN 10 35 2.5 TDK C3225X5R1E106M 10 25 Output capacitor selection Using tantalum or electrolytic capacitors, the selection is made referring to ESR and voltage rating rather than by a specific capacitance value. The output capacitor has to satisfy the output voltage ripple requirements. At a given switching frequency, small inductor values are useful to reduce the size of the choke but increase the inductor current ripple. Thus, to reduce the output voltage ripple a low ESR capacitor is required. To reduce jitter noise between different switching regulators in the system, it is preferable to work with an output voltage ripple greater than 25 mV. Concerning the load transient requirements, the Equivalent Series Resistance (ESR) of the output capacitor must satisfy the following relationship: Equation 37 ESR ≤ VRIPPLE,MAX ∆IL,MAX where VRIPPLE is the maximum tolerable ripple voltage. In addition, the ESR must be high enough to meet stability requirements. The output capacitor zero must be lower than the switching frequency: Equation 38 fSW > fZ = 42/53 1 2π ⋅ ESR ⋅ C out PM6675S Application information If ceramic capacitors are used, the output voltage ripple due to inductor current ripple is negligible. Then the inductance should be smaller, reducing the size of the choke. In this case it is important that output capacitor can adsorb the inductor energy without generating an over-voltage condition when the system changes from a full load to a no load condition. The minimum output capacitance can be chosen by the following equation: Equation 39 C OUT ,min = L ⋅ ILOAD ,MAX 2 Vf 2 − Vi 2 where Vf is the output capacitor voltage after the load transient, while Vi is the output capacitor voltage before the load transient. In Table 13 are listed some tested polymer capacitors. Table 13. Evaluated output capacitors Series Capacitance (µF) Rated voltage (V) ESR max @100 kHz (mΩ) 4TPE220MF 220 4V 15 to 25 4TPE150MI 220 4V 18 4TPC220M 220 4V 40 TNCB OE227MTRYF 220 2.5 V 25 Manufacturer SANYO HITACHI 8.1.4 MOSFETs selection In a notebook application, power management efficiency is a high level requirement. The power dissipation on the power switches becomes an important factor in the selection of switches. Losses of high-side and low-side MOSFETs depend on their working condition. Considering the high-side MOSFET, the power dissipation is calculated as: Equation 40 PDHighSide = Pconduction + Pswitching Maximum conduction losses are approximately given by: Equation 41 Pconduction = RDSon ⋅ VOUT 2 ⋅ ILOAD,MAX VIN. min 43/53 Application information PM6675S where RDS(on) is the drain-source on-resistance of the control MOSFET. Switching losses are approximately given by: Equation 42 Pswitching = VIN ⋅ (ILOAD (max) − 2 ∆IL ∆I ) ⋅ t on ⋅ fsw VIN ⋅ (ILOAD (max) + L ) ⋅ t off ⋅ fsw 2 2 + 2 where tON and tOFF are the turn-on and turn-off times of the MOSFET and depend on the gate-driver current capability and the gate charge Qgate. A greater efficiency is achieved with low RDSon. Unfortunately low RDSon MOSFETs have a great gate charge. As general rule, the RDS(on) x Qgate product should be minimized to find the suitable MOSFET. Logic-level MOSFETs are recommended, as long as low-side and high-side gate drivers are powered by VVCC = +5 V. The breakdown voltage of the MOSFETs (VBRDSS) must be greater than the maximum input voltage VINmax. Below some tested high-side MOSFETs are listed. Table 14. Evaluated high-side MOSFETs Manufacturer Type RDS(on) (mΩ) Gate charge (nC) Rated reverse voltage (V) ST STS12NH3LL 10.5 12 30 IR IRF7811 9 18 30 In buck converters the power dissipation of the synchronous MOSFET is mainly due to conduction losses: Equation 43 PDLowSide ≅ Pconduction Maximum conduction losses occur at the maximum input voltage: Equation 44 ⎛ V Pconduction = RDSon ⋅ ⎜1 − OUT ⎜ V IN,MAX ⎝ ⎞ ⎟ ⋅ ILOAD,MAX 2 ⎟ ⎠ The synchronous rectifier should have the lowest RDS(on) as possible. When the high-side MOSFET turns on, high dV/dt of the phase node can bring up even the low-side gate through its gate-drain capacitance CRRS, causing a cross-conduction problem. Once again, the choice of the low-side MOSFET is a trade-off between on resistance and gate charge; a good selection should minimizes the ratio CRSS / CGS where Equation 45 CGS = CISS − CRSS Below some tested low-side MOSFETs are listed. 44/53 PM6675S Application information Table 15. Evaluated low-side MOSFETs Manufacturer Type RDS(on) (mΩ) CGD \ CGS Rated reverse voltage (V) ST STS12NH3LL 13.5 0.069 30 ST STS25NH3LL 4.0 0.011 30 IR IRF7811 24 0.054 30 Dual N-MOS can be used in applications with lower output current. Table 16 shows some suitable dual MOSFETs for applications requiring about 3 A. Table 16. 8.1.5 Suitable dual MOSFETs Manufacturer Type RDSon (mΩ) Gate charge (nC) Rated reverse voltage (V) ST STS8DNH3LL 25 10 30 IR IRF7313 46 33 30 Diode selection A rectifier across the synchronous switch is recommended. The rectifier works as a voltage clamp across the synchronous rectifier and reduces the negative inductor swing during the dead time between turning the high-side MOSFET off and the synchronous rectifier on. Moreover it increases the efficiency of the system. Choose a schottky diode as long as its forward voltage drop is very little (0.3 V). The reverse voltage should be greater than the maximum input voltage VINmax and a minimum recovery reverse charge is preferable. Table 17 shows some evaluated diodes. Table 17. Evaluated recirculation rectifiers Manufacturer Type Forward voltage (V) Rated reverse voltage (V) Reverse current (µA) ST STPS1L30M 0.34 30 0.00039 ST STPS1L30A 0.34 30 0.00039 45/53 Application information 8.1.6 PM6675S VOUT current limit setting The valley current limit is set by RCSNS and must be chosen to support the maximum load current. The valley of the inductor current ILvalley is: Equation 46 ILvalley = ILOAD (max) − ∆IL 2 The output current limit depends on the current ripple as shown in Figure 48: Figure 48. Valley current limit waveforms Current Inductor current MAX LOAD 2 MAX LOAD 1 Inductor current Valley current limit Time As the valley threshold is fixed, the greater the current ripple, the greater the DC output current will be. If an output current limit greater than ILOAD(max) over all the input voltage range is required, the minimum current ripple must be considered in the previous formula. Then the resistor RCSNS is: Equation 47 RCSNS = RDSon ⋅ ILvalley 100uA where RDSon is the drain-source on-resistance of the low-side switch. Consider the temperature effect and the worst case value in RDSon calculation (typically +0.4 % / °C). The accuracy of the valley current also depends on the offset of the internal comparator (±5 mV). The negative valley-current limit (if the device works in forced-PWM mode) is given by: Equation 48 INEG = 46/53 110mV RDSon PM6675S 8.1.7 Application information All ceramic capacitors application Design of external feedback network depends on the output voltage ripple across the output capacitors ESR. If the ripple is great enough (at least 20 mV), the compensation network simply consists of a CINT capacitor. Figure 49. Integrative compensation Ton One-shot generator VSNS VOUT + PWM Comparator - VREF Vr=0.9 V + COMP gm Integrator CFILT RINT - 0.6V VREF CINT The stability of the system firstly depends on the output capacitor zero frequency. It must be verified that: Equation 49 fSW > k ⋅ fZout = k 2π ⋅ R out C out where k is a free design parameter greater than unity (k > 3) . It determines the minimum integrator capacitor value CINT: Equation 50 CINT > gm Vref ⎛f ⎞ Vo 2π ⋅ ⎜ SW − fZout ⎟ k ⎝ ⎠ ⋅ If the ripple on the COMP pin is greater than the integrator output dynamic (150 mV), an additional capacitor Cfilt could be added in order to reduce its amplitude. If q is the desired attenuation factor of the output ripple, select: 47/53 Application information PM6675S Equation 51 C filt = CINT ⋅ (1 − q) q In order to reduce noise on the COMP pin, it's possible to introduce a resistor RINT that, together with CINT and Cfilt, becomes a low pass filter. The cutoff frequency fCUT must be much greater (10 or more times) than the switching frequency: Equation 52 RINT = 2π ⋅ fCUT 1 CINT ⋅ CFILT CINT + CFILT For most applications both RINT and Cfilt are unnecessary. If the ripple is very small (e.g. such as with ceramic capacitors), a further compensation network, called "Virtual ESR" network, is needed. This additional part generates a triangular ripple that substitutes the ESR output voltage ripple. The complete compensation scheme is represented in Figure 50. Figure 50. Virtual ESR network L R R1 CINT VOUT C RINT PWM Comparator Ton Generation Block + gm + - VREF Vr CFILT Select C as shown: Equation 53 C > 5 ⋅ CINT 48/53 Integrator 0.6V 1.237V PM6675S Application information Then calculate R in order to have enough ripple voltage on the integrator input: Equation 54 R= L R VESR ⋅ C Where RVESR is the new virtual output capacitor ESR. A good trade-off is to consider an equivalent ESR of 30-50 mΩ , even though the choice depends on inductor current ripple. Then choose R1 as follows: Equation 55 ⎛ 1 ⎞ ⎟ R ⋅ ⎜⎜ π ⋅ fZ ⋅ C ⎟⎠ ⎝ R1 = 1 R− π ⋅ fZ ⋅ C 49/53 Package mechanical data 9 PM6675S Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. Table 18. VFQFPN-24 4 mm x 4 mm mechanical data mm. Dim. Min Typ Max 0.80 0.90 1.00 A1 0.0 0.05 A2 0.65 0.80 D 4.00 D1 3.75 E 4.00 E1 3.75 A θ P 50/53 12° 0.24 0.42 e 0.50 N 24.00 Nd 6.00 Ne 6.00 0.40 0.60 L 0.30 0.50 b 0.18 D2 1.95 2.10 2.25 E2 1.95 2.10 2.25 0.30 PM6675S Package mechanical data Figure 51. Package dimensions 51/53 Revision history 10 PM6675S Revision history Table 19. 52/53 Document revision history Date Revision 14-Feb-2008 1 Changes Initial release PM6675S Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2008 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 53/53