POWER SPLITTER – High Precision Power Chip Divider The content of this specification may change without notification 10/23/08 HOW TO ORDER PPS -10 A- 50R0 M LF Terminal Material SnPb = Leave Blank Lead Free = LF Packaging M = tape/reel 5,000 pcs O = tape/reel 1,000 pcs FEATURES Impedance 50Ω High Frequency Splitter is constructed of thin film resistive material Circuit Configuration A or B Size 0402 = 05 0603 = 16 0805 = 10 Power splitter with excellent high frequency characteristics for applications from DC~20GHz 1206 = 18 2010 = 12 This product has a small reflection feature, allowing for superior in high frequency applications Series Precision Power Splitter Allows for high density mounting Bit error is restrained by keeping high frequency digital signal stable PPS-A ELECTRICAL CHARACTERISTICS Item Size Circuit Configuration Operating Frequency 6 ± 0.5dB Insertion Loss 6 ± 1.0dB Split Deviation 1.3 VSWR 1.5 Input Power at 70°C Max Overload Power Resistance Operating Temperature Packaging PPS-16A 0603 A DC~20GHz DC~10GHz 10~20GHz 0.3dB max DC~10GHz 10~20GHz 100mW 200mW PPS-10 PPS-18A 0805 1206 A A DC~17.5GHz DC~15GHz DC~10GHz DC~10GHz 10~17.5GHz 10~15GHz 0.3dB max 0.3dB max DC~10GHz DC~10GHz 10~17.5GHz 10~15GHz 125mW 250mW 250mW 500mW R1 = R2 = R3 = 50Ω typical -40°C ~ +125°C 1,000/Reel or 5,000/Reel PPS-B ELECTRICAL CHARACTERISTICS CIRCUIT Item PPS-10B PPS-18B Size 0805 1206 Circuit Configuration B B Resistance Tolerance ±0.1%, ±0.5%, ±1% TCR ±50ppm/°C 33 mW 42 mW Power Rating per Package 100 mW 125 mW Resistance Operating Temp. Range Package Quantity American Accurate Components, Inc. Configuration A Configuration B ±50ppm/°C Power Rating per Element Rated Operating Temp PPS-12A 2010 A DC~10GHz DC~7.5GHz 7.5~10GHz 0.3dB max DC~7.5GHz 7.5~10GHz 500mW 1000mW 70°C R1 = R2 = R3 = 50Ω typical -55°C ~ +125°C 1,000/Reel or 5,000/Reel 188 Technology Drive, Unit H, Irvine, CA 92618 TEL: 949-453-9888 FAX: 949-453-8889 1 POWER SPLITTER – High Precision Power Chip Divider The content of this specification may change without notification 10/23/08 DERATING CURVE – Circuit A DERATING CURVE – Circuit B DIMENSIONS (mm) L W a b t PPS-05A Series 1.00 ± 0.2 0.50 ± 0.2 0.4 ± 0.1 0.30 ± 0.1 0.4 ± 0.10 PPS-16A 1.60 ± 0.2 0.80 ± 0.2 0.4 ± 0.1 0.30 ± 0.1 0.4 ± 0.10 PPS-10A 2.00 ± 0.2 1.25±0.2 0.4 ± 0.1 0.30 ± 0.1 0.4 ± 0.10 PPS-18A 3.20 ± 0.2 1.60 ± 0.2 0.3 ± 0.1 0.35 ± 0.1 0.4 ± 0.10 PPS-12A 0.50 ± 0.2 2.5 ± 0.2 0.35 ± 0.1 0.65 ± 0.1 0.8 ± 0.15 SCHEMATIC LEGEND 1. 2. 3. 4. 5. SCHEMATIC – Circuit A Thin Film Resistor Overcoat Resin Terminal (SnPb or Lead Free) Marking (dot to indicate direction & bar) Alumina Substrate PERFORMANCE Item Test Condition Tolerance Short Time Overload 2.5 times of the rated voltage shall be applied for 5 seconds. ±0.1% Rated Load Life Apply rated voltage for 90 min followed by a pause of 30 min at 70±3°C for 1000 hours. ±0.25% Moisture Load Life Temperature Cycle The chip divider is applied rated voltage for 90 min at 60±2°C 90～95%RH for 1000 hours. [-55°C (30min)-R.T.(3min)-+125°C(30min)-R.T.(3min)] is repeated 5 cycles. ±0.1% Soldering Heat Resistance Leave NR in melt solder of 260±5°C for 10±1 seconds. ±0.1% Strength Between Terminals Distance between fulcrums : 90mm; Bending width : 3mm; Substrate: Glass epoxy t=1.6mm ±0.1% Solderability Leave NR in melted solder of 235±5°C for 3±0.5 seconds. Insulation Resistance A minute after 500 DC ±0.25% ≥95% of the surface should be wet ≥ 1000M Ω *** Custom Designs Available American Accurate Components, Inc. 188 Technology Drive, Unit H, Irvine, CA 92618 TEL: 949-453-9888 FAX: 949-453-8889 2