PQ1Xxx1M2ZPH Series PQ1Xxx1M2ZPH Series Features Low Output Current, Compact Surface Mount Type Low Power-Loss Voltage Regulators ■ Outline Dimensions (Unit : mm) 1.Compact surface mount package (2.9×1.6×1.1mm) 2.Low power-loss (Dropout voltage: TYP. 0.11 V/MAX. 0.26V at IO=60mA) Also compatible ceramic capacitors because of suppressing oscillation level 3.High ripple rejection (TYP. 70dB) 4.Built-in ON/OFF control function (Dissipation current at OFF-state: MAX. 1μA) 5.Built-in overcurrent and overheat protection functions *It is available for every 0.1V of output voltage (1.3V to 5.0V) 6.RoHS directive compliant (1.9) 5 4 X 3 0 1 2 3 (0.95) 5-0.4±0.1 (0.95) Lead finish identification mark 1.3MAX 0 to 0.1 1.Cellular phones 2.Cordless phones 3.Personal information tools (PDA) 4.Cameras/Camcoders 5.PCMCIA cards for notebook PCs 15°MAX. 0.15±0.1 Applications 0.2MIN. 0.2MIN. 2.8±0.3 ( ) : Typical dimensions Product mass:(0.015g) Model Line-up Output Voltage (TYP.) 1.5V 1.8V 2.5V 2.6V 2.7V 2.8V 2.9V 1.6±0.2 (0.3) 1.1±0.2 3.3MAX. (2.9TYP. excluding remaining gate) 1 5 1 2 Model No. Output Voltage (TYP.) PQ1X151M2ZPH 3.0V PQ1X181M2ZPH 3.3V 3.5V PQ1X251M2ZPH PQ1X261M2ZPH 3.7V PQ1X271M2ZPH 4.0V PQ1X281M2ZPH 4.5V PQ1X291M2ZPH 5.0V Model No. PQ1X301M2ZPH PQ1X331M2ZPH PQ1X351M2ZPH PQ1X371M2ZPH PQ1X401M2ZPH PQ1X451M2ZPH PQ1X501M2ZPH 2 3 3 Control circuit 4 4 5 DC input (VIN) GND ON/OFF control terminal (VC) Noise reduction (Nr) DC output (VO) Lead finish:Lead-free solder plating (Composition: Sn2Cu) Absolute Maximum Ratings (Ta=25°C) Parameter *1 Input voltage Symbol VIN *1 ON/OFF control terminal voltage VC Output current IO *2 Power dissipation PD *3 Junction temperature Tj Operating temperature Topr Storage temperature Tstg Soldering temperature Tsol Rating 9 9 300 350 150 -30 to +85 -55 to +150 270(10s) Unit V V mA mW °C °C °C °C *1 All are open except GND and applicable terminals. *2 At mounted on PCB *3 Overheat protection may operate at Tj:125°C to 150°C Notice The content of data sheet is subject to change without prior notice. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. 1 Sheet No.: OP06028 PQ1Xxx1M2ZPH Series Electrical Characteristics (Unless otherwise specified,VIN=VO(TYP) + 1.0V, IO=30mA,VC=1.8V, Ta=25°C) Parameter Conditions VO - - RegL1 Io=5 to 60mA RegL2 Io=5 to 100mA RegL3 Io=5 to 150mA Output voltage 4 Input 5 voltage VIN Iop Output peak current Recommended output current Load regulation RegI Temperature coefficient of output voltage TCVO IO=10mA, Tj=-25 to +75°C RR Refer to Fig.2 8 Dropout voltage VI-O1 IO=60mA VI-O2 IO=150mA ON-state voltage for control VC(ON) - ON-state current for control OFF-state voltage for control IC(ON) VC(OFF) VC=1.8V Quiescent current Iq IO=0mA Output OFF-state dissipation current Iqs VC=0.2V Unit MAX. 9 V V - mA 150 mA 2.3 - 180 300 - 10 50 mV 20 100 mV 40 160 mV 3.0 20 mV 0.05 - mV/°C VIN=VO(TYP)+1V to VO(TYP)+6V(MAX.9.0V) Vno(rms) 10Hz<f<100kHz, CnF=0.1μF, IO=30mA Output noise voltage TYP. Refer to the following table.1 Line regulation Ripple rejection 6 MIN. Symbol 70 dB Refer to the following table.2 - 7 7 1.8 - - 0.11 0.26 0.20 0.4 μV V - - V 5 - 30 0.4 μA V 150 200 μA - 1 μA 4 Applied to PQ1X151M2ZPH and PQ1X181M2ZPH 5 Output current shall be the value when output voltage lowers 0.3V from the voltage at IO=30mA. 6 Excluding PQ1X151M2ZPH and PQ1X181M2ZPH 7 Input voltage when output voltage falls 0.1V from that at Vin=Vo(TYP)+1.0V. 8 In case that the control terminal ( ③ pin) is open, output voltage should be OFF state. Table.2 Output Noise Voltage Table.1 Output Voltage (VIN=VO(TYP)+1.0V, IO=30mA, VC=1.8V, Ta=25°C) Model No. PQ1X151M2ZPH PQ1X181M2ZPH PQ1X251M2ZPH PQ1X261M2ZPH PQ1X271M2ZPH PQ1X281M2ZPH PQ1X291M2ZPH PQ1X301M2ZPH PQ1X331M2ZPH PQ1X351M2ZPH PQ1X371M2ZPH PQ1X401M2ZPH PQ1X451M2ZPH PQ1X501M2ZPH Symbol MIN. 1.440 1.740 2.440 2.540 2.640 2.740 2.840 VO 2.940 3.234 3.430 3.626 3.920 4.410 4.900 TYP. 1.5 1.8 2.5 2.6 2.7 2.8 2.9 3.0 3.3 3.5 3.7 4.0 4.5 5.0 MAX. 1.560 1.860 2.560 2.660 2.760 2.860 2.960 3.060 3.366 3.570 3.774 4.080 4.590 5.100 (VIN=VO(TYP)+1.0V, IO=30mA, VC=1.8V,Cn=0.1μF,10Hz<f<100kHz,Ta=25°C) Unit Model No. Symbol MIN. PQ1X151M2ZPH PQ1X181M2ZPH PQ1X251M2ZPH PQ1X261M2ZPH PQ1X271M2ZPH PQ1X281M2ZPH PQ1X291M2ZPH Vno(rms) PQ1X301M2ZPH PQ1X331M2ZPH PQ1X351M2ZPH PQ1X371M2ZPH PQ1X401M2ZPH PQ1X451M2ZPH PQ1X501M2ZPH - V TYP. 15 15 25 25 25 25 25 30 30 35 35 40 45 50 MAX. - Unit μV Fig.1 Test Circuit 1 Iq, Iqs A 5 A 2 IO 4.7μF 1μF VIN 3 A VC IC V 4 (ON) VO RL 0.01μF Sheet No.: OP06028 2 PQ1Xxx1M2ZPH Series Fig.2 Test Circuit for Ripple Rejection 1 + 5 ei 2 ~ eo 3 VIN RL 4 V ~ VC f=400Hz(sine wave) ei(rms)=100mV VIN=VO(TYP)+1.0V VC=1.8V IO=10mA RR=20log(ei(rms)/eo(rms)) Fig.3 Power Dissipation vs. Ambient Temperature Fig.4 100 Relative output voltage (%) Power dissipation P D (mW) 400 300 200 100 75 50 25 Ta=25°C 0 0 -30 -25 Overcurrent Protection Characteristics (Typical Value) 0 25 50 75 85 100 125 150 0 0.1 0.2 0.3 Output current I O (A) Ambient temperature Ta (°C) 0.4 Note) Oblique line portion:Overheat protection may operate in this area. Fig.6 4 60 VIN=3.8V 50 IO=30mA VC=1.8V 40 CO=4.7μF 30 (Ceramic capacitor) 20 10 0 –10 –20 –30 –40 –50 –60 –30–20 0 20 40 60 80 100 120 140 Junction temperature Tj (°C) Output voltage VO (V) Output voltage fluctuation VO (mV) F i g.5 Output Voltage Fluctuation vs . Junction Temperature (PQ1X301M2ZPH)(Typical Value) Output Voltage vs. Input Voltage (PQ1X301M2ZPH)(Typical Value) 3 2 Ta=25°C CIN=1μF (Ceramic capacitor) CO=4.7μF (Ceramic capacitor) R L= 1 0 0 1 2 3 4 5 Input voltage VIN (V) 6 7 Sheet No.: OP06028 3 PQ1Xxx1M2ZPH Series Fig.7 Circuit Operating Current vs. Input Voltage (PQ1X301M2ZPH)(Typical Value) 0.35 Ta=25°C CIN=1μF (Ceramic capacitor) CO=4.7μF (Ceramic capacitor) 10 Dropout voltage VI-O (mV) Circuit operating current I BIAS (mA) 15 Fig.8 Dropout Voltage vs. Junction Temperature (PQ1X301M2ZPH)(Typical Value) 5 R L= 0 0 1 2 3 4 5 Input voltage VIN (V) 6 120 100 80 60 40 20 0 –30–20 0 20 40 60 80 100 120 140 Junction temperature Tj (°C) Dropout voltage VI-O (V) 0.3 0.15 VI-O1: I O=60mA 0.1 0.05 80 140 F i g.11 VI-O2 : I O=150mA 0.2 90 Ripple rejection RR (dB) Quiescent current I q (μA) 160 0.25 F i g.10 R i pple Rejection vs . Input Ripple F r equency(PQ1X281M2ZPH)(Typical Value) VIN =VO +1V VC=1.8V I O=0A 180 VIN :Voltage when output voltage is 95% 0 –30–20 0 20 40 60 80 100 120 140 Junction temperature Tj (°C) 7 Fig.9 Quiescent Current vs. Junction Temperature (Typical Value) 200 0.3 70 60 50 Cn=0.1μF Cn=0.01μF N o Cn 40 Ta=25°C 30 VIN=3.8V 20 VC=1.8V IO=10mA 10 ei (rms) =100mV 0 CO=10μF 0.1 1 10 100 Input ripple frequency f (kHz) Dropout V o ltage vs. Output Current (Typical Value) 0.2 0.1 0 0 50 100 150 Output current I O (mA) Sheet No.: OP06028 4