RF1172B • • • • Ideal Front-End Filter for European Wireless Receivers Low-Loss, Coupled-Resonator Quartz Design Simple External Impedance Matching Surface-Mount Ceramic Case with 52 mm2 Footprint 433.92 MHz SAW Filter The RF1172B is a low-loss, compact, and economical surface-acoustic-wave (SAW) filter designed to provide front-end selectivity in 433.92 MHz receivers. Receiver designs using this filter include superhet with 10.7 MHz or 500 kHz IF, direct conversion and superregen. Typical applications of these receivers are wireless remote-control and security devices operating in Europe under ETSI I-ETS 300 220. This coupled-resonator filter (CRF) uses selective null placement to provide suppression, typically greater than 40 dB, of the LO and image spurious responses of superhet receivers with 10.7 MHz IF. RFM’s advanced SAW design and fabrication technology is utilized to achieve high performance and very low loss with simple external impedance matching (not included). Our new patent pending solder seal process utilizes a Faraday shield lid, which improves out of band rejection. SM8558-8 Case Electrical Characteristics Characteristic Center Frequency at 25°C Absolute Frequency Tolerance from 433.92 MHz Insertion Loss 3 dB Bandwidth Rejection Sym fc Notes ∆fC 1, 2 IL 1 BW3 1, 2 Minimum Units MHz ±80 kHz 3.0 5.0 dB 500 600 800 kHz 40 50 15 30 1 Ultimate Temperature Maximum 433.92 at fc - 21.4 MHz (Image) at fc - 10.7 MHz (LO) Typical dB 80 Operating Case Temp. TC -40 Turnover Temperature TO 15 Turnover Frequency fO Freq. Temp. Coefficient FTC Frequency Aging Absolute Value during the First Year |fA| External Impedance Series Inductance L Shunt Capacitance C 3, 4 5 1 Lid Symbolization (in addition to Lot and/or Date Codes) 25 +85 °C 35 °C fc MHz 0.032 ppm/°C2 ≤10 ppm/yr 47 nH 11 pF RFM RF1172B CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. Notes: 1. Unless noted otherwise, all measurements are made with the filter installed in the specified test fixture which is connected to a 50 Ω test system with VSWR ≤ 1.2:1. The test fixture L and C are adjusted for minimum insertion loss at the filter center frequency, fc. Note that insertion loss and bandwidth are dependent on the impedance matching component values and quality. 2. The frequency fc is defined as the midpoint between the 3dB frequencies. 3. Where noted, specifications apply over the entire specified operating temperature range. 4. The turnover temperature, TO, is the temperature of maximum (or turnover) frequency, fo. The nominal frequency at any case temperature, Tc, may 5. 6. 7. 8. be calculated from: f = fo [1 - FTC (To - Tc)2]. Frequency aging is the change in fc with time and is specified at +65°C or less. Aging may exceed the specification for prolonged temperatures above +65°C. Typically, aging is greatest the first year after manufacture, decreasing significantly in subsequent years. The design, manufacturing process, and specifications of this device are subject to change without notice. One or more of the following U.S. Patents apply: 4,54,488, 4,616,197, and others pending. All equipment designs utilizing this product must be approved by the appropriate government agency prior to manufacture or sale. RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com RF1172B-102401 Page 1 of 2 433.92 MHz SAW Filter Absolute Maximum Ratings Rating Value Units +13 dBm ±30 VDC -40 to +85 °C Incident RF Power DC Voltage between any 2 pins (Observe ESD Precautions) Case Temperature 5 Typical Filter Response Typical filter responses are shown below. The actual response is dependent on external impedance matching and circuit layout. Illustrated frequencies and minimum rejection for LO and IMAGE are shown only for superhet receivers with 10.7 MHz IF 0 dB -1 0 -10 Amplitude Response Amplitude Response LO -20 -30 -40 Image -50 -2 -3 -4 Min 3dB Passband at 25 oC -5 -60 -6 -70 -7 -8 -80 5 MHz/div Frequency Electrical Connections Pin 150 KHz/div Frequency Case Design Connection 1 Input 2 Ground 3 Output Return 4 Case Ground 5 Output 6 Ground 7 Input Return 8 Case Ground Dimensions RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. Millimeters Min Max Inches Min Max A 8.71 0.343 B 6.04 0.238 C 2.03 0.080 D 0.79 Nominal 0.031 Nominal E 1.14 Nominal 0.045 Nominal F 1.98 Nominal 0.078 Nominal G 0.79 Nominal 0.031 Nominal H 6.91 0.040 K 4.24 0.167 M 0.81 0.032 N 2.54 Nominal 0.100 Nominal P 1.91 Nominal 0.075 Nominal E-mail: [email protected] http://www.rfm.com RF1172B-102401 Page 2 of 2