RSB6.8S Diodes ESD Protection diode RSB6.8S 1.6±0.1 F7 !Features 1) Small surface mounting type. (EMD2) 2) High reliability. 1.2±0.05 !External dimensions (Units : mm) !Application Noise suppression on signal line 0.12±0.05 0.3±0.05 0.8±0.05 0.6±0.1 !Construction Silicon epitaxial planar ROHM : EMD2 EIAJ : SC-79 JEDEC : SOD-523 !Circuit !Absolute maximum ratings (Ta=25°C) Symbol Limits Unit Peak pulse power (tp=10×1000µs) Ppk 10 W Power dissipation P 150 mW Parameter Junction temperature Tj 150 °C Storage temperature Tstg −55∼+150 °C Operation temperature Topr −55∼+150 °C !Electrical characteristics (Ta=25°C) Symbol Min. Typ. Max. Zener voltage VZ 5.780 − 7.820 V IZ=1mA Reverse current IR − − 0.5 µA VR=3.5V Junction capacitance Ct − 30 − pF VR=0V, F=1MHz Parameter ∗Zener voltage (Vz) shall be measured at 40ms after loading current. Unit Conditions RSB6.8S Diodes !Others IEC-61000-4-2 Item Equipment composition Charge discharge capacitance Discharge resistamce : 150pF : 330Ω Criterion Repeat by 10 times No erroneous operation Contact In air : ±8kV : ±15kV 100 100 REVERSE SURGE POWER DISSIPATION : PRSM (W) CAPACITANCE BETWEEN TERMINALS : Ct (pF) !Electrical characteristic curves (Ta=25°C) 10 1 0 1 2 3 4 5 6 REVERSE VOLTAGE : VR (V) Fig.1 Capacitance between terminals characteristics 7 10 1 0.1 1 PULSE WIDTH : TW (ms) Fig.2 Surge power dissipation 10 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document use silicon as a basic material. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.0