16-4&8*%5).0%6-"5*0/".1-*'*&3 SA01 • SA01-6 )551888"1&9.*$305&$)$0. "1&9 M I C R O T E C H N O L O G Y FEATURES • SINGLE SUPPLY OPERATION • WIDE SUPPLY RANGE — 16-100V • 20A CONTINUOUS OUTPUT • PROGRAMMABLE CURRENT LIMIT • SHUTDOWN CONTROL • HERMETIC PACKAGE • 2 IN2 FOOTPRINT 4" $ 64" 5& #F0 APPLICATIONS 10-pin Power DIP PACKAGE STYLE DE • BRUSH TYPE MOTOR CONTROL • PELTIER CONTROL • REACTIVE LOADS • MAGNETIC COILS (MRI) • ACTIVE MAGNETIC BEARING • VIBRATION CANCELLING TYPICAL APPLICATION DESCRIPTION The SA01 amplifier is a pulse width modulation amplifier that can supply 2KW to the load. The full bridge output amplifier can be operated from a single power supply over a wide range of voltages. An error amplifier is included which can provide gain for the velocity control loop in brush type motor control applications. Current limit is programmable by a single resistor. A shutdown input turns off all four drivers of the H bridge output. A precision reference output is provided for use in offsetting the error amplifier. The error amplifier can then be scaled for standard input signals. The amplifier is protected from shorts to supply or ground. The H bridge output MOSFETs are protected from thermal overloads by directly sensing the temperature of the die. The 10-pin hermetic power package occupies only 2 square inches of board space and is isolated. 7*/ $ ' &" 065 m*/ 7 3&' 74 " 065 &" 18. */ 4)%/ *4&/4& '*-5&3 4" 3'*-5&3 4)65 %08/ $'*-5&3 . 5 # 065 (/% 3-*.*5 Motor Driver With Tach Feedback BLOCK DIAGRAM 73&'065 461 3&' &"065 m*/ */ (/% &3303 ".1 74 #065 "065 EXTERNAL CONNECTIONS $'*-5&3 065165 %3*7&34 18. $633&/5 -*.*5 "/% 4)65%08/ $0/530- m*/ */ &"065 (/% *4&/4& 4)%/ '*-5&3 3&' "4&"065 (0&4.03&104*5*7&)*()45"5&0'"065 */$3&"4&4"/%)*()45"5&0'#065 %&$3&"4&4 501 7*&8 4)%/ '*-5&3 3'*-5&3 #065 *4&/4& 74 m "065 ' $ 3-*.*5 3-*.*5 *-*.*5 APEX MICROTECHNOLOGY CORPORATION • TELEPHONE (520) 690-8600 • FAX (520) 888-3329 • ORDERS (520) 690-8601 • EMAIL [email protected] SA01 • SA01-6 ABSOLUTE MAXIMUM RATINGS SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS SPECIFICATIONS PARAMETER SUPPLY VOLTAGE, +VS OUTPUT CURRENT, peak POWER DISSIPATION, internal TEMPERATURE, pin solder - 10s TEMPERATURE, junction2 TEMPERATURE, storage OPERATING TEMPERATURE RANGE, case SHUTDOWN VOLTAGE REFERENCE LOAD CURRENT ERROR AMP INPUT ± TEST CONDITIONS2 MIN SA01 TYP 100V 30A 185W1 300°C 150°C –65 to +150°C –55 to +125°C 10V 10mA 0 to +12V MAX SA01-6 MIN TYP MAX UNITS ERROR AMP OFFSET VOLTAGE, initial TC = 25°C 10 * OFFSET VOLTAGE, vs. temperature Full Temperature Range5 50 50 BIAS CURRENT, initial TC = 25°C 5 * BIAS CURRENT, vs. temperature Full Temperature Range5 400 400 OFFSET CURRENT, initial TC = 25°C 1 * OFFSET CURRENT, vs. temperature Full Temperature Range5 80 80 COMMON MODE VOLTAGE RANGE4 2 8 * * COMMON MODE REJECTION, DC4 75 * SLEW RATE 15 * OPEN LOOP GAIN4 75 * GAIN BANDWIDTH PRODUCT 2 * mV µV/°C µA nA/°C µA nA/°C V dB V/µS dB MHz OUTPUT TOTAL RON .25 * EFFICIENCY, 10A OUTPUT VS = 100V 97 * SWITCHING FREQUENCY Full temperature range5 35.3 42 48.7 35 42 49 CURRENT, continuous4 20 * CURRENT, peak4 30 * Ω % KHz A A REFERENCE VOLTAGE IREF = 5mA 7.46 7.50 7.54 * * * VOLTAGE VS. TEMP Full temperature range5 50 50 OUTPUT CURRENT 5 5 LOAD REGULATION4 20 50 * * LINE REGULATION 1 * V PPM/°C mA PPM/mA PPM/V POWER SUPPLY VOLTAGE CURRENT CURRENT, shutdown Full temperature range5 16 50 IOUT = 0, IREF = 0, 76 Full temperature range5 IREF = 0 SHUTDOWN TRIP POINT .18 INPUT CURRENT THERMAL2 RESISTANCE, junction to case4 RESISTANCE, junction to air4 TEMPERATURE RANGE, case NOTES: 1. 2. 3. 4. 5. CAUTION 100 16 90 50 76 100 93 V mA 25 * mA .22 * 100 * * V nA Full temp range, for each transistor 1.0 * Full temperature range 12 * Meets full range specifications5 –25 +85 –55 125 °C/W °C/W °C Each of the two active output transistors can dissipate 125W, however the N-channel will be about 1/3 of the total dissipated power. Internal connection resistance is .05Ω. Unless otherwise noted: TC = 25°C. Long term operation at the maximum junction temperature will result in reduced product life. Derate internal power dissipation to achieve high MTTF. For guidance, refer to the heatsink data sheet. Guaranteed but not tested. Full temperature range specifications apply to the operating case temperature range as specified under THERMAL. For the SA01 these specifications are guaranteed but not tested. For the SA01-6 these specifications are tested over the SA01-6 operating case temperature range. The SA01 is constructed from MOSFET transistors. ESD handling procedures must be observed. The internal substrate contains beryllia (BeO). Do not break the seal. If accidentally broken, do not crush, machine, or subject to temperatures in excess of 850°C to avoid generating toxic fumes. APEX MICROTECHNOLOGY CORPORATION • 5980 NORTH SHANNON ROAD • TUCSON, ARIZONA 85741 • USA • APPLICATIONS HOTLINE: 1 (800) 546-2739 ."9*.6.$0/5*/6064065165 5+$ 4063$&50%3"*/%*0%&70-5"(& $"4&5&.1&3"563&5$$ '-:#"$,%*0%&4 $ &// )" $ 7 4 1 50 65 0 "# /&/$)"/ 0* 4&/4& #0655 " 747 747 70-5"(&%3017 &3303".14."--4*(/"-("*/ '&50/3&4*45"/$& - //& )" 1$ m m $"4&5&.1&3"563&5$$ m m m m - "//& /$) , , , . . '3&26&/$:')[ #3*%(&%06516548*/( $ $ $ +6/$5*0/5&.1&3"563& #3*%(&%3*7&$633&/5*065" /03."-*;&%3&'&3&/$&%3*'5 %65:$:$-& m m $"4&5&.1&3"563&5$$ 65 747 065165$633&/5" &3303".14."--4*(/"-1)"4& , , , . . '3&26&/$:')[ $"4&5&.1$ 0 747 # 26*&4$&/5$633&/5*2N" 747 m $"4&5&.1&3"563&5$ $ +6/$5*0/5&.1&3"563&5+$ '-:#"$,$633&/5*4%" 26*&4$&/5$633&/5%3*'5 m 0/3&4*45"/$&ų 065165$633&/5" $"4&5&.1$ 65 $"4&5&.1&3"563&5$ $ 0 &"$)06516553"/4*4503 $"4&5&.1$ " 01&/-0011)"4&þ $"4&5&.1$ 70-5"(&%30174<"065#065>7 70-5"(&%301 1&3$&/5)*() /03."-*;&%48*5$)*/('3&26&/$: /03."-*;&%$-0$,%3*'5 01&/-001("*/3&410/4&"E# 108&3%&3"5*/( TYPICAL PERFORMANCE GRAPHS /03."-*;&%3&'&3&/$&73&'9 */5&3/"-108&3%*44*1"5*0/18 SA01 • SA01-6 $0/530-&"0657 APEX MICROTECHNOLOGY CORPORATION • TELEPHONE (520) 690-8600 • FAX (520) 888-3329 • ORDERS (520) 690-8601 • EMAIL [email protected] OPERATING CONSIDERATIONS SA01 • SA01-6 GENERAL the shutdown signal is high the output will be disabled. Please read Application Note 30 on "PWM Basics". Refer to Application Note 1 "General Operating Considerations" for helpful information regarding power supplies, heat sinking and mounting. Visit www.apexmicrotech.com for design tools that help automate pwm filter design; heat sink selection; Apex’s complete Application Notes library; Technical Seminar Workbook; and Evaluation Kits. PROTECTION CIRCUITS CURRENT LIMIT The current limit function sets a peak limit on current flow in pin 8 (Isense). This limits load current and also limits current in the event of a short of either output to +Vs. This circuit can trip anytime during the conduction period and will hold the output transistors off for the remainder of that conduction period. For proper operation the current limit sense resistor must be connected as shown in the external connection diagram. It is recommended that the resistor be a non-inductive type. Load current flows in pin 8. No current flows in pin 10 (Shutdown/filter) so no error will be introduced by the length of the connection to pin 10. However, the voltage at pin 10 is compared to GND (pin 4) and an error could be introduced if the grounded end of RLIMIT is not directly tied to pin 4. Good circuit board layout practice would be to connect RLIMIT directly between pins 8 and 4. Switching noise spikes will invariably be found at pin 8. The amplitude and duration will be load dependent. The noise spikes could trip the current limit threshold which is only 200 mV. RFILTER and CFILTER should be adjusted so as to reduce the switching noise well below 200 mV to prevent false current limiting. The sum of the DC level plus the noise peak will determine the current limiting value. Suggested starting values are CFILTER = .01µF, RFILTER = 5k. The required value of RLIMIT may be calculated by: RLIMIT = .2 V / ILIMIT where RLIMIT is the required resistor value, and ILIMIT is the maximum desired current. There are two conditions which will latch all the output transistors off. The first of these conditions is activation of the high side current limit. Specifically, current in pin 7 (+VS) is monitored. The DC trip level is about 35A and response time about 5us. As actual currents increase the response time decreases. The external fault generally associated with this condition is shorting one of the outputs to ground. However, a load fault can also activate this high side current limit if the current rise time is less than the response time of the filter discussed under “Current Limit”. The second of these conditions is activation of any of the four output transistor over-temperature sensors at about 165°C. Ambient temperature, air flow, amplifier mounting problems and all the previously mentioned high current faults contribute to junction temperature. When either of these protection circuits are activated, the root fault must be corrected and power cycled to restore normal operation. DEAD TIME There is a dead time between the on and off of each output. The dead time removes the possibility of a momentary conduction path through the upper and lower transistors of each half bridge output during the switching interval. During the dead time all output transistors are off. Noise or flyback may be observed at the outputs during this time due to the high impedance of the outputs in the off state. This will vary with the nature of the load. 3&'065 3 $ 505"$) 4*(/"- 3 3 m*/ 3 3 ' */ $ 3 &"065 3 SHUTDOWN The shutdown circuitry makes use of the internal current limiting circuitry. The two functions may be externally combined as shown below in Figure 1. RLIMIT will normally be a very low value resistor and can be considered zero for this application. RSD and RFILTER form a voltage divider for the shutdown signal. After a suitable noise filter is designed for the current limit adjust the value of RSD to give 317 mV of shutdown signal at pin 10 when the shutdown signal is high. This means pin 10 will reach the 200 mV trip point in about one time constant with low output current and 34% less time as output current 4)%/'*-5&3 4)65%08/ increases. The voltage at 4*(/" pin 10 is referenced to pin 4 (GND). CFILTER will filter $'*-5&3 3'*-5&3 both the current limit noise spikes and the shutdown *4&/4& signal. Shutdown and 3-*.*5 current limit operate on each cycle of the internal '*(63& switching rate. As long as '*(63& ERROR AMPLIFIER The internal error amplifier is an operational amplifier. For highest loop accuracy it is best to configure the op amp as an integrator (See Figure 2). Feedback can be adjusted with appropriate poles and zeroes to properly compensate the velocity loop for optimum stability. The op amp is operated from a single supply voltage generated internally. The non-inverting input of the op amp does not have a common mode range which includes ground. R2 and R7 are used with the reference voltage provided at pin 5 to bias the non-inverting input to +5 volts, which is approximately half of the voltage supplied internally to the op amp. Similarly, R1 and the parallel combination of R5 R6 are selected to bias the inverting input also at +5 volts. Resistors R1 R2 must be matched. Likewise the parallel combination of R5 R6 must be matched with R7. The source impedances of the tach and the signal source may affect the matching and should be considered in the design. This data sheet has been carefullyCORPORATION checked and is believed to be NORTH reliable, however, no responsibility is assumed for possible inaccuracies omissions. All specifications HOTLINE: are subject to1change notice. APEX MICROTECHNOLOGY • 5980 SHANNON ROAD • TUCSON, ARIZONA 85741 •orUSA • APPLICATIONS (800)without 546-2739 SA01U REV H MARCH 2007 © 2007 Apex Microtechnology Corp.