AMD SC3200UFH-266

AMD Geode™ SC3200 Processor
Data Book
March 2004
Publication ID: Revision 5.1
AMD Geode™ SC3200 Processor Data Book
© 2004 Advanced Micro Devices, Inc. All rights reserved.
The contents of this document are provided in connection with Advanced Micro
Devices, Inc. (“AMD”) products. AMD makes no representations or warranties with
respect to the accuracy or completeness of the contents of this publication and
reserves the right to make changes to specifications and product descriptions at
any time without notice. No license, whether express, implied, arising by estoppel
or otherwise, to any intellectual property rights is granted by this publication.
Except as set forth in AMD’s Standard Terms and Conditions of Sale, AMD
assumes no liability whatsoever, and disclaims any express or implied warranty,
relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual
property right.
AMD’s products are not designed, intended, authorized or warranted for use as
components in systems intended for surgical implant into the body, or in other
applications intended to support or sustain life, or in any other application in which
the failure of AMD’s product could create a situation where personal injury, death,
or severe property or environmental damage may occur. AMD reserves the right to
discontinue or make changes to its products at any time without notice.
Contacts
www.amd.com [email protected]
Trademarks
AMD, the AMD Arrow logo, and combinations thereof, and Geode, Virtual System Architecture, and
WebPAD are trademarks of Advanced Micro Devices, Inc.
Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and other
jurisdictions.
MMX is trademark of Intel Corporation.
Other product names used in this publication are for identification purposes only and may be trademarks
of their respective companies.
2
AMD Geode™ SC3200 Processor Data Book
Contents
Revision 5.1
Contents
List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.0
AMD Geode™ SC3200 Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1.1
1.2
2.0
Architecture Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.1
2.2
2.3
2.4
2.5
3.0
Ball Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Strap Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Multiplexing Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
General Configuration Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
4.1
4.2
4.3
4.4
4.5
5.0
GX1 Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Video Processor Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Core Logic Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Super I/O Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Clock, Timers, and Reset Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Signal Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.1
3.2
3.3
3.4
4.0
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Configuration Block Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Multiplexing, Interrupt Selection, and Base Address Registers . . . . . . . . . . . . . . . . . . . . . . . . . 88
WATCHDOG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
High-Resolution Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Clock Generators and PLLs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
SuperI/O Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Module Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Configuration Structure / Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Standard Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Real-Time Clock (RTC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
System Wakeup Control (SWC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
ACCESS.bus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Legacy Functional Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
AMD Geode™ SC3200 Processor Data Book
3
Revision 5.1
6.0
Core Logic Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
6.1
6.2
6.3
6.4
7.0
Module Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345
Debugging and Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367
8.1
9.0
Feature List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Module Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
Chipset Register Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
Video Processor Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327
7.1
7.2
7.3
8.0
Contents
Testability (JTAG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369
9.1
9.2
9.3
General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375
AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380
10.0 Package Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 439
10.1 Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 439
10.2 Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 441
Appendix A
A.1
A.2
4
Support Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443
Order Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443
Data Book Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443
AMD Geode™ SC3200 Processor Data Book
List of Figures
Revision 5.1
List of Figures
Figure 1-1.
Figure 3-1.
Figure 3-2.
Figure 3-3.
Figure 4-1.
Figure 4-2.
Figure 4-3.
Figure 5-1.
Figure 5-2.
Figure 5-3.
Figure 5-4.
Figure 5-5.
Figure 5-6.
Figure 5-7.
Figure 5-8.
Figure 5-9.
Figure 5-10.
Figure 5-11.
Figure 5-12.
Figure 5-13.
Figure 5-14.
Figure 5-15.
Figure 5-16.
Figure 5-17.
Figure 5-18.
Figure 5-19.
Figure 6-1.
Figure 6-2.
Figure 6-3.
Figure 6-4.
Figure 6-5.
Figure 6-6.
Figure 6-7.
Figure 6-8.
Figure 6-9.
Figure 6-10.
Figure 6-11.
Figure 6-12.
Figure 6-13.
Figure 6-14.
Figure 6-15.
Figure 7-1.
Figure 7-2.
Figure 7-3.
Figure 7-4.
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Signal Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
432-EBGA Ball Assignment Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
481-TEPBGA Ball Assignment Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
WATCHDOG Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Clock Generation Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Recommended Oscillator External Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
SIO Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Detailed SIO Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Structure of the Standard Configuration Register File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Standard Configuration Registers Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Recommended Oscillator External Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
External Oscillator Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Divider Chain Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Power Supply Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Typical Battery Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Typical Battery Current: Battery Backed Power Mode @ TC = 25°C . . . . . . . . . . . . . . . . . 124
Typical Battery Current: Normal Operation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Interrupt/Status Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Bit Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Start and Stop Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
ACCESS.bus Data Transaction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
ACCESS.bus Acknowledge Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
A Complete ACCESS.bus Data Transaction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
UART Mode Register Bank Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
IRCP/SP3 Register Bank Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Core Logic Module Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Non-Posted Fast-PCI to ISA Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
PCI to ISA Cycles with Delayed Transaction Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
ISA DMA Read from PCI Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
ISA DMA Write to PCI Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
PCI Change to Sub-ISA and Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
PIT Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
PIC Interrupt Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
PCI and IRQ Interrupt Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
SMI Generation for NMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
General Purpose Timer and UDEF Trap SMI Tree Example . . . . . . . . . . . . . . . . . . . . . . . . 181
PRD Table Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
AC97 V2.0 Codec Signal Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
Audio SMI Tree Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
Typical Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
Video Processor Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328
NTSC 525 Lines, 60 Hz, Odd Field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330
NTSC 525 Lines, 60 Hz, Even Field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330
VIP Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331
AMD Geode™ SC3200 Processor Data Book
5
Revision 5.1
Figure 7-5.
Figure 7-6.
Figure 7-7.
Figure 7-8.
Figure 7-9.
Figure 7-10.
Figure 7-11.
Figure 7-12.
Figure 7-13.
Figure 7-14.
Figure 9-1.
Figure 9-2.
Figure 9-3.
Figure 9-4.
Figure 9-5.
Figure 9-6.
Figure 9-7.
Figure 9-8.
Figure 9-9.
Figure 9-10.
Figure 9-11.
Figure 9-12.
Figure 9-13.
Figure 9-14.
Figure 9-15.
Figure 9-16.
Figure 9-17.
Figure 9-18.
Figure 9-19.
Figure 9-20.
Figure 9-21.
Figure 9-22.
Figure 9-23.
Figure 9-24.
Figure 9-25.
Figure 9-26.
Figure 9-27.
Figure 9-28.
Figure 9-29.
Figure 9-30.
Figure 9-31.
Figure 9-32.
Figure 9-33.
Figure 9-34.
Figure 9-35.
Figure 9-36.
Figure 9-37.
Figure 9-38.
Figure 9-39.
Figure 9-40.
Figure 9-41.
Figure 9-42.
Figure 9-43.
Figure 9-44.
Figure 9-45.
6
List of Figures
Capture Video Mode Bob Example Using One Video Frame Buffer . . . . . . . . . . . . . . . . . . 333
Capture Video Mode Weave Example Using Two Video Frame Buffers . . . . . . . . . . . . . . . 334
Video Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335
Horizontal Downscaler Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336
Linear Interpolation Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337
Mixer/Blender Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338
Graphics/Video Frame with Alpha Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340
Color Key and Alpha Blending Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342
TFT Power Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 343
PLL Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344
Differential Input Sensitivity for Common Mode Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378
Drive level and Measurement Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380
Memory Controller Drive Level and Measurement Points . . . . . . . . . . . . . . . . . . . . . . . . . . 381
Memory Controller Output Valid Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383
Read Data In Setup and Hold Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383
Video Input Port Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384
TFT Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385
ACB Signals: Rising Time and Falling Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 387
ACB Start and Stop Condition Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 387
ACB Start Condition Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 388
ACB Data Bit Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 388
Testing Setup for Slew Rate and Minimum Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389
V/I Curves for PCI Output Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390
PCICLK Timing and Measurement Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391
Load Circuits for Maximum Time Measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392
Output Timing Measurement Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393
Input Timing Measurement Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394
PCI Reset Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394
Sub-ISA Read Operation Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397
Sub-ISA Write Operation Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398
LPC Output Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399
LPC Input Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399
IDE Reset Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400
Register Transfer to/from Device Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 402
PIO Data Transfer to/from Device Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 404
Multiword DMA Data Transfer Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406
Initiating an UltraDMA Data in Burst Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408
Sustained UltraDMA Data In Burst Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409
Host Pausing an UltraDMA Data In Burst Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . 410
Device Terminating an UltraDMA Data In Burst Timing Diagram . . . . . . . . . . . . . . . . . . . . 411
Host Terminating an UltraDMA Data In Burst Timing Diagram . . . . . . . . . . . . . . . . . . . . . . 412
Initiating an UltraDMA Data Out Burst Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413
Sustained UltraDMA Data Out Burst Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414
Device Pausing an UltraDMA Data Out Burst Timing Diagram . . . . . . . . . . . . . . . . . . . . . . 415
Host Terminating an UltraDMA Data Out Burst Timing Diagram . . . . . . . . . . . . . . . . . . . . . 416
Device Terminating an UltraDMA Data Out Burst Timing Diagram . . . . . . . . . . . . . . . . . . . 417
Data Signal Rise and Fall Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420
Source Differential Data Jitter Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420
EOP Width Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 421
Receiver Jitter Tolerance Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 421
UART, Sharp-IR, SIR, and Consumer Remote Control Timing Diagram . . . . . . . . . . . . . . . 422
Fast IR (MIR and FIR) Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423
Standard Parallel Port Typical Data Exchange Timing Diagram . . . . . . . . . . . . . . . . . . . . . 424
Enhanced Parallel Port Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425
ECP Forward Mode Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 426
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
List of Figures
Figure 9-46.
Figure 9-47.
Figure 9-48.
Figure 9-49.
Figure 9-50.
Figure 9-51.
Figure 9-52.
Figure 9-53.
Figure 9-54.
Figure 9-55.
Figure 9-56.
Figure 9-57.
Figure 9-58.
Figure 10-1.
Figure 10-2.
Figure 10-3.
ECP Reverse Mode Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 427
AC97 Reset Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 428
AC97 Sync Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 428
AC97 Clocks Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429
AC97 Data TIming Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 430
AC97 Rise and Fall Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 431
AC97 Low Power Mode Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 432
PWRBTN# Trigger and ONCTL# Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433
GPWIO and ONCTL# Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433
Power-Up Sequencing With PWRBTN# Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 434
Power-Up Sequencing Without PWRBTN# Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . 435
TCK Measurement Points and Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436
JTAG Test Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437
Heatsink Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 440
432-Terminal EBGA Package (Body Size: 40x40x1.72 mm; Pitch: 1.27 mm) . . . . . . . . . . . 441
481-Terminal TEPBGA Package (Body Size: 40x40x2.38 mm; Pitch: 1.27 mm) . . . . . . . . 442
AMD Geode™ SC3200 Processor Data Book
7
Revision 5.1
8
List of Figures
AMD Geode™ SC3200 Processor Data Book
List of Tables
Revision 5.1
List of Tables
Table 2-1.
Table 2-2.
Table 3-1.
Table 3-2.
Table 3-3.
Table 3-4.
Table 3-5.
Table 3-6.
Table 3-7.
Table 3-8.
Table 3-9.
Table 4-1.
Table 4-2.
Table 4-3.
Table 4-4.
Table 4-5.
Table 4-6.
Table 4-7.
Table 4-8.
Table 5-1.
Table 5-2.
Table 5-3.
Table 5-4.
Table 5-5.
Table 5-6.
Table 5-7.
Table 5-8.
Table 5-9.
Table 5-10.
Table 5-11.
Table 5-12.
Table 5-13.
Table 5-14.
Table 5-15.
Table 5-16.
Table 5-17.
Table 5-18.
Table 5-19.
Table 5-20.
Table 5-21.
Table 5-22.
Table 5-23.
Table 5-24.
Table 5-25.
Table 5-26.
SC3200 Memory Controller Register Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
SC3200 Memory Controller Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Signal Definitions Legend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
432-EBGA Ball Assignment - Sorted by Ball Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
432-EBGA Ball Assignment - Sorted Alphabetically by Signal Name . . . . . . . . . . . . . . . . . . 38
481-TEPBGA Ball Assignment - Sorted by Ball Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
481-TEPBGA Ball Assignment - Sorted Alphabetically by Signal Name . . . . . . . . . . . . . . . 54
Strap Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Two-Signal/Group Multiplexing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Three-Signal/Group Multiplexing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Four-Signal/Group Multiplexing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
General Configuration Block Register Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Multiplexing, Interrupt Selection, and Base Address Registers . . . . . . . . . . . . . . . . . . . . . . . 88
WATCHDOG Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
High-Resolution Timer Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Crystal Oscillator Circuit Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Core Clock Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Strapped Core Clock Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Clock Generator Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
SIO Configuration Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
LDN Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Standard Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
SIO Control and Configuration Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
SIO Control and Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Relevant RTC Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
RTC Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Relevant SWC Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Relevant IRCP/SP3 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
IRCP/SP3 Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Relevant Serial Ports 1 and 2 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Serial Ports 1 and 2 Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Relevant ACB1 and ACB2 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
ACB1 and ACB2 Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Relevant Parallel Port Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Parallel Port Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Crystal Oscillator Circuit Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
System Power States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
RTC Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
RTC Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Divider Chain Control / Test Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Periodic Interrupt Rate Encoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
BCD and Binary Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Standard RAM Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Extended RAM Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Time Range Limits for CEIR Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
AMD Geode™ SC3200 Processor Data Book
9
Revision 5.1
Table 5-27.
Table 5-28.
Table 5-29.
Table 5-30.
Table 5-31.
Table 5-32.
Table 5-33.
Table 5-34.
Table 5-35.
Table 5-36.
Table 5-37.
Table 5-38.
Table 5-39.
Table 5-40.
Table 5-41.
Table 5-42.
Table 5-43.
Table 5-44.
Table 5-45.
Table 5-46.
Table 5-47.
Table 5-48.
Table 5-49.
Table 5-50.
Table 5-51.
Table 5-52.
Table 5-53.
Table 5-54.
Table 5-55.
Table 5-56.
Table 5-57.
Table 5-58.
Table 5-59.
Table 5-60.
Table 5-61.
Table 5-62.
Table 6-1.
Table 6-2.
Table 6-3.
Table 6-4.
Table 6-5.
Table 6-6.
Table 6-7.
Table 6-8.
Table 6-9.
Table 6-10.
Table 6-11.
Table 6-12.
Table 6-13.
Table 6-14.
Table 6-15.
Table 6-16.
Table 6-17.
Table 6-18.
Table 6-19.
10
List of Tables
Banks 0 and 1 - Common Control and Status Register Map . . . . . . . . . . . . . . . . . . . . . . . . 133
Bank 1 - CEIR Wakeup Configuration and Control Register Map . . . . . . . . . . . . . . . . . . . . 133
Banks 0 and 1 - Common Control and Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Bank 1 - CEIR Wakeup Configuration and Control Registers . . . . . . . . . . . . . . . . . . . . . . . 135
ACB Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
ACB Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Parallel Port Register Map for First Level Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Parallel Port Register Map for Second Level Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Parallel Port Bit Map for First Level Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Parallel Port Bit Map for Second Level Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Bank 0 Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Bank Selection Encoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Bank 1 Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Bank 2 Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Bank 3 Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Bank 0 Bit Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Bank 1 Bit Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Bank 2 Bit Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Bank 3 Bit Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Bank 0 Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Bank Selection Encoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Bank 1 Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Bank 2 Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Bank 3 Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Bank 4 Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Bank 5 Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Bank 6 Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Bank 7 Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Bank 0 Bit Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Bank 1 Bit Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Bank 2 Bit Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Bank 3 Bit Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Bank 4 Bit Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Bank 5 Bit Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Bank 6 Bit Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Bank 7 Bit Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Physical Region Descriptor Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
UltraDMA/33 Signal Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Cycle Multiplexed PCI / Sub-ISA Balls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
PIC Interrupt Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
Wakeup Events Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Power Planes Control Signals vs. Sleep States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Power Planes vs. Sleep/Global States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Power Management Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Device Power Management Programming Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Bus Masters That Drive Specific Slots of the AC97 Interface . . . . . . . . . . . . . . . . . . . . . . . 183
Physical Region Descriptor Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
Cycle Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
PCI Configuration Address Register (0CF8h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support Summary . . . 192
F0BAR0: GPIO Support Registers Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
F0BAR1: LPC Support Registers Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
F1: PCI Header Registers for SMI Status and ACPI Support Summary . . . . . . . . . . . . . . . 196
F1BAR0: SMI Status Registers Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
F1BAR1: ACPI Support Registers Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
List of Tables
Table 6-20.
Table 6-21.
Table 6-22.
Table 6-23.
Table 6-24.
Table 6-25.
Table 6-26.
Table 6-27.
Table 6-28.
Table 6-29.
Table 6-30.
Table 6-31.
Table 6-32.
Table 6-33.
Table 6-34.
Table 6-35.
Table 6-36.
Table 6-37.
Table 6-38.
Table 6-39.
Table 6-40.
Table 6-41.
Table 6-42.
Table 6-43.
Table 6-44.
Table 6-45.
Table 6-46.
Table 6-47.
Table 6-48.
Table 6-49.
Table 7-1.
Table 7-2.
Table 7-3.
Table 7-4.
Table 7-5.
Table 7-6.
Table 7-7.
Table 7-8.
Table 8-1.
Table 9-1.
Table 9-2.
Table 9-3.
Table 9-4.
Table 9-5.
Table 9-6.
Table 9-7.
Table 9-8.
Table 9-9.
Table 9-10.
Table 9-11.
Table 9-12.
Table 9-13.
Table 9-14.
Table 9-15.
Table 9-16.
F2: PCI Header Registers for IDE Controller Support Summary . . . . . . . . . . . . . . . . . . . . . 198
F2BAR4: IDE Controller Support Registers Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
F3: PCI Header Registers for Audio Support Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
F3BAR0: Audio Support Registers Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
F5: PCI Header Registers for X-Bus Expansion Support Summary . . . . . . . . . . . . . . . . . . 201
F5BAR0: I/O Control Support Registers Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
PCIUSB: USB PCI Configuration Register Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
USB_BAR: USB Controller Registers Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
ISA Legacy I/O Register Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support . . . . . . . . . . . 206
F0BAR0+I/O Offset: GPIO Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240
F0BAR1+I/O Offset: LPC Interface Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . 244
F1: PCI Header Registers for SMI Status and ACPI Support . . . . . . . . . . . . . . . . . . . . . . . 252
F1BAR0+I/O Offset: SMI Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253
F1BAR1+I/O Offset: ACPI Support Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
F2: PCI Header/Channels 0 and 1 Registers for IDE Controller Configuration . . . . . . . . . . 273
F2BAR4+I/O Offset: IDE Controller Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . 277
F3: PCI Header Registers for Audio Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
F3BAR0+Memory Offset: Audio Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 280
F5: PCI Header Registers for X-Bus Expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294
F5BAR0+I/O Offset: X-Bus Expansion Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298
PCIUSB: USB PCI Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
USB_BAR+Memory Offset: USB Controller Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303
DMA Channel Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
DMA Page Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318
Programmable Interval Timer Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
Programmable Interrupt Controller Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321
Keyboard Controller Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324
Real-Time Clock Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
Miscellaneous Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
Valid Mixing/Blending Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339
Truth Table for Alpha Blending . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341
F4: PCI Header Registers for Video Processor Support Summary . . . . . . . . . . . . . . . . . . . 345
F4BAR0: Video Processor Configuration Registers Summary . . . . . . . . . . . . . . . . . . . . . . 345
F4BAR2: VIP Support Registers Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347
F4: PCI Header Registers for Video Processor Support Registers . . . . . . . . . . . . . . . . . . . 348
F4BAR0+Memory Offset: Video Processor Configuration Registers . . . . . . . . . . . . . . . . . . 350
F4BAR2+Memory Offset: VIP Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363
JTAG Mode Instruction Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367
Electro Static Discharge (ESD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369
Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370
Power Planes of External Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371
System Conditions Used to Measure SC3200 Current During On State . . . . . . . . . . . . . . . 372
DC Characteristics for On State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372
DC Characteristics for Active Idle, Sleep, and Off States . . . . . . . . . . . . . . . . . . . . . . . . . . 373
Ball Capacitance and Inductance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373
Balls with PU/PD Resistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374
Buffer Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375
Default Levels for Measurement of Switching Parameters . . . . . . . . . . . . . . . . . . . . . . . . . 380
Memory Controller Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382
Video Input Port Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384
TFT Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385
ACCESS.bus Input Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386
ACCESS.bus Output Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386
AMD Geode™ SC3200 Processor Data Book
11
Revision 5.1
Table 9-17.
Table 9-18.
Table 9-19.
Table 9-20.
Table 9-21.
Table 9-22.
Table 9-23.
Table 9-24.
Table 9-25.
Table 9-26.
Table 9-27.
Table 9-28.
Table 9-29.
Table 9-30.
Table 9-31.
Table 9-33.
Table 9-34.
Table 9-35.
Table 9-36.
Table 9-37.
Table 9-38.
Table 9-39.
Table 9-40.
Table 9-41.
Table 9-42.
Table 9-43.
Table 9-44.
Table 9-45.
Table 10-1.
Table 10-2.
Table A-1.
Table A-2.
12
List of Tables
PCI AC Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389
PCI Clock Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391
PCI Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392
Measurement Condition Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393
Sub-ISA Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395
LPC and SERIRQ Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399
IDE General Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400
IDE Register Transfer to/from Device Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . 401
IDE PIO Data Transfer to/from Device Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . 403
IDE Multiword DMA Data Transfer Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405
IDE UltraDMA Data Burst Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407
USB Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 418
UART, Sharp-IR, SIR, and Consumer Remote Control Timing Parameters . . . . . . . . . . . . 422
Fast IR Port Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423
Standard Parallel Port Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 424
ECP Forward Mode Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 426
ECP Reverse Mode Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 427
AC Reset Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 428
AC97 Sync Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 428
AC97 Clocks Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429
AC97 I/O Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 430
AC97 Signal Rise and Fall Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 431
AC97 Low Power Mode Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 432
PWRBTN# Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433
Power Management Event (GPWIO) and ONCTL# Timing Parameters . . . . . . . . . . . . . . . 433
Power-Up Sequence Using the Power Button Timing Parameters . . . . . . . . . . . . . . . . . . . 434
Power-Up Sequence Not Using the Power Button Timing Parameters . . . . . . . . . . . . . . . . 435
JTAG Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436
qJC (×C/W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 439
Case-to-Ambient Thermal Resistance Example @ 85×C . . . . . . . . . . . . . . . . . . . . . . . . . . 439
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443
Edits to Current Revision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 445
AMD Geode™ SC3200 Processor Data Book
AMD Geode™ SC3200 Processor
Revision 5.1
1
1.0AMD Geode™
SC3200 Processor
1.1
General Description
The AMD Geode™ SC3200 processor is a member of the
AMD Geode family of fully integrated x86 system chips.
The SC3200 processor includes:
• The Geode GX1 processor module combines advanced
CPU performance with MMX™ support, fully accelerated 2D graphics, a 64-bit synchronous DRAM
(SDRAM) interface, a PCI bus controller, and a display
controller.
• A low-power TFT Video Processor module with a Video
Input Port (VIP), and a hardware video accelerator for
scaling, filtering, and color space conversion.
• The Core Logic module includes: PC/AT functionality, a
USB interface, an IDE interface, a PCI bus interface, an
LPC bus interface, Advanced Configuration Power Interface (ACPI) version 1.0 compliant power management,
and an audio codec interface.
• The SuperI/O module has: three serial ports (UART1,
UART2, and UART3 with fast infrared), a parallel port,
two ACCESS.bus (ACB) interfaces, and a real-time
clock (RTC).
These features, combined with the device’s low power consumption, enable a small form factor design making it ideal
as the core for a WebPAD™ system application.
Figure 1-1 shows the relationships between the modules.
GX1
Video Processor
Memory Controller
Display
Controller
2D Graphics
Accelerator
CPU
Core
Video
Mixer
Video
Scaling
TFT I/F
Config.
Block
PCI Bus
Controller
Video Input Port (VIP)
Host Interface
Fast-PCI Bus
Clock & Reset Logic
Fast X-Bus
Core Logic
IDE I/F
RTC
ACB1
I/F
PCI/Sub-ISA
Bus I/F
PCI Bus
Bridge
USB
Parallel
Port
PIT
PIC
SuperI/O
DMAC
GPIO
Pwr Mgmnt
Audio Codec I/F
Configuration
LPC I/F
ISA Bus I/F
X-Bus
ACB2
I/F
UART1
UART2
ISA Bus
I/F
UART3
& IR
Figure 1-1. Block Diagram
AMD Geode™ SC3200 Processor Data Book
13
Revision 5.1
1.2
AMD Geode™ SC3200 Processor
Features
General Features
Video Processor Module
■ 32-Bit x86 processor, up to 266 MHz, with MMX instruc-
■ Video Accelerator:
tion set support
■ Memory controller with 64-bit SDRAM interface
■ 2D graphics accelerator
■ CCIR-656 video input port with direct video for full
screen display
■ PC/AT functionality
■ PCI bus controller
■ IDE interface, two channels
■ USB, three ports, OHCI (OpenHost Controller Interface)
version 1.0 compliant
■ Audio, AC97/AMC97 version 2.0 compliant
■ Virtual System Architecture™ (VSA) technology support
■ Power management, ACPI (Advanced Configuration
Power Interface) version 1.0 compliant
■ Package:
— 432-Terminal EBGA (Enhanced Ball Grid Array)
— 481-Terminal TEPBGA (Thermally Enhanced Plastic
Ball Grid Array)
GX1 Processor Module
■ CPU Core:
— 32-Bit x86, 266 MHz, with MMX compatible instruction set support
— 16 KB unified L1 cache
— Integrated FPU (Floating Point Unit)
— Re-entrant SMM (System Management Mode)
enhanced for VSA
■ 2D Graphics Accelerator:
—
—
—
—
Accelerates BitBLTs, line draw and text
Supports all 256 raster operations
Supports transparent BLTs
Runs at core clock frequency
■ Memory Controller:
— 64-Bit SDRAM interface
— 66 MHz to 100 MHz frequency range
— Direct interface with CPU/cache, display controller
and 2D graphic accelerator
— Supports clock suspend and power-down/
self-refresh
— Up to two banks of SDRAM (8 devices total) or one
SODIMM
■ Display Controller:
— Hardware graphics frame buffer compress/
decompress
— Hardware cursor, 32x32 pixels
14
— Flexible video scaling support of up to 800%
(horizontally and vertically)
— Bilinear interpolation filters (with two taps, and eight
phases) to smooth output video
■ Video/Graphics Mixer:
— 8-bit value alpha blending
— Three blending windows with constant alpha value
— Color key
■ Video Input Port (VIP):
— Video capture or display
— CCIR-656 and VESA Video Interface Port v1.1
compliant
— Lock display timing to video input timing (GenLock)
— Able to transfer video data into main memory
— Direct video transfer for full screen display
— Separate memory location for VBI
■ TFT Interface:
— Direct connection to TFT panels
— 800x600 non-interlaced TFT @ 16 bpp graphics,
up to 85 Hz
— 1024x768 non-interlaced TFT @ 16 bpp graphics,
up to 75 Hz
— TFT on IDE: FPCLK max is 40 MHz
— TFT on Parallel Port: FPCLK max is 80 MHz
Core Logic Module
■ Audio Codec Interface:
— AC97/AMC97 (Rev. 2.0) codec interface
— Six DMA channels
■ PC/AT Functionality:
— Programmable Interrupt Controller (PIC),
8259A-equivalent
— Programmable Interval Timer (PIT), 8254-equivalent
— DMA Controller (DMAC), 8237-equivalent
■ Power Management:
—
—
—
—
—
ACPI v1.0 compliant
Sx state control of three power planes
Cx/Sx state control of clocks and PLLs
Thermal event input
Wakeup event support:
– Three general-purpose events
– AC97 codec event
– UART2 RI# signal
– Infrared (IR) event
■ General Purpose I/Os (GPIOs):
— 27 multiplexed GPIO signals
■ Low Pin Count (LPC) Bus Interface:
— Specification v1.0 compatible
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
AMD Geode™ SC3200 Processor
■ PCI Bus Interface:
—
—
—
—
—
PCI v2.1 compliant with wakeup capability
32-Bit data path, up to 33 MHz
Glueless interface for an external PCI device
Fixed priority
3.3V signal support only
■ Sub-ISA Bus Interface:
— Up to 16 MB addressing
— Supports a chip select for ROM or Flash EPROM
boot device
— Supports either:
– M-Systems DiskOnChip DOC2000 Flash file
system
– NAND EEPROM
— Supports up to two chip selects for external I/O
devices
— 8-Bit (optional 16-bit) data bus width
— Shares balls with PCI signals
— Is not a subtractive agent
■ IDE Interface:
— Two IDE channels for up to four external IDE devices
— Supports ATA-33 synchronous DMA mode transfers,
up to 33 MB/s
Other Features
■ High-Resolution Timer:
— 32-Bit counter with 1 µs count interval
■ WATCHDOG Timer:
— Interfaces to INTR, SMI, Reset
■ Clocks:
— Input (external crystals):
– 32.768 KHz (internal clock oscillator)
– 27 MHz (internal clock oscillator)
— Output:
– AC97 clock (24.576 MHz)
– Memory controller clock (66 MHz to 100 MHz)
– PCI clock (33 MHz)
■ JTAG Testability:
— Bypass, Extest, Sample/Preload, IDcode, Clamp, HiZ
■ Voltages
—
—
—
—
—
Internal logic: 266 or 233 MHz @ 1.8V
Standby logic: 266 or 233 MHz @ 1.8V
I/O: 3.3V
Standby I/O: 3.3V
Battery (if used): 3.0V
■ Universal Serial Bus (USB):
— USB OpenHCI v1.0 compliant
— Three ports
SuperI/O Module
■ Real-Time Clock (RTC):
— DS1287, MC146818 and PC87911 compatible
— Multi-century calendar
■ ACCESS.bus (ACB) Interface:
— Two ACB interface ports
■ Parallel Port:
— EPP 1.9 compliant
— IEEE 1284 ECP compliant, including level 2
■ Serial Port (UART):
— UART1, 16550A compatible (SIN, SOUT, BOUT
pins), used for SmartCard interface
— UART2, 16550A compatible
— Enhanced UART with fast Infrared (IR)
AMD Geode™ SC3200 Processor Data Book
15
Revision 5.1
16
AMD Geode™ SC3200 Processor
AMD Geode™ SC3200 Processor Data Book
Architecture Overview
Revision 5.1
2
2.0Architecture Overview
As illustrated in Figure 1-1 on page 13, the SC3200 processor contains the following modules in one integrated
device:
• GX1 Module:
— Combines advanced CPU performance with MMX
support, fully accelerated 2D graphics, a 64-bit
synchronous DRAM (SDRAM) interface and a PCI
bus controller. Integrates GX1 silicon revision 8.1.1.
• Video Processor Module:
— A low-power TFT support module with a video input
port, and a hardware video accelerator for scaling,
filtering and color space conversion.
• Core Logic Module:
— Includes PC/AT functionality, an IDE interface, a
Universal Serial Bus (USB) interface, ACPI v1.0
compliant power management, and an audio codec
interface.
• SuperI/O Module:
— Includes two Serial Ports, an Infrared (IR) Port, a
Parallel Port, two ACCESS.bus interfaces, and a
Real-Time Clock (RTC).
2.1
GX1 Module
The GX1 processor (silicon revision 8.1.1) is the central
module of the SC3200. For detailed information regarding
the GX1 module, refer to the AMD Geode™ GX1 Processor Data Book and the AMD Geode™ GX1 Processor Silicon Revision 8.1.1 Specification Update documents.
AMD Geode™ SC3200 Processor Data Book
The SC3200 processor’s device ID is contained in the GX1
module. Software can detect the revision by reading the
DIR0 and DIR1 Configuration registers (see Configuration
registers in the AMD Geode™ GX1 Processor Data Book).
The AMD Geode™ SC3200 Specification Update document contains the specific values.
2.1.1
Memory Controller
The GX1 module is connected to external SDRAM devices.
For more information see Section 3.4.2 "Memory Interface
Signals" on page 65, and the “Memory Controller” chapter
in the AMD Geode™ GX1 Processor Data Book.
There are some differences in the SC3200 processor’s
memory controller and the stand-alone GX1 processor’s
memory controller:
1)
There is drive strength/slew control in the SC3200 that
is not in the GX1. The bits that control this function are
in the MC_MEM_CNTRL1 and MC_MEM_CNTRL2
registers. In the GX1 processor, these bits are marked
as reserved.
2)
The SC3200 supports two banks of memory. The GX1
supports four banks of memory. In addition, the
SC3200 supports a maximum of eight devices and the
GX1 supports up to 32 devices. With this difference,
the MC_BANK_CFG register is different.
Table 2-1 summarizes the 32-bit registers contained in the
SC3200 processor’s memory controller. Table 2-2 gives
detailed register/bit formats.
17
Revision 5.1
Architecture Overview
Table 2-1. SC3200 Memory Controller Register Summary
GX_BASE+
Memory Offset
Width
(Bits)
Type
Name/Function
Reset Value
8400h-8403h
32
R/W
MC_MEM_CNTRL1. Memory Controller Control Register 1
248C0040h
8404h-8407h
32
R/W
MC_MEM_CNTRL2. Memory Controller Control Register 2
00000801h
8408h-840Bh
32
R/W
MC_BANK_CFG. Memory Controller Bank Configuration
41104110h
840Ch-840Fh
32
R/W
MC_SYNC_TIM1. Memory Controller Synchronous Timing
Register 1
2A733225h
8414h-8417h
32
R/W
MC_GBASE_ADD. Memory Controller Graphics Base
Address Register
00000000h
8418h-841Bh
32
R/W
MC_DR_ADD. Memory Controller Dirty RAM Address
Register
00000000h
841Ch-841Fh
32
R/W
MC_DR_ACC. Memory Controller Dirty RAM Access
Register
0000000xh
Table 2-2. SC3200 Memory Controller Registers
Bit
Description
GX_BASE+ 8400h-8403h
31:30
29
28:27
26
MC_MEM_CNTRL1 (R/W)
Reset Value: 248C0040h
MDCTL (MD[63:0] Drive Strength). 11 is strongest, 00 is weakest.
RSVD (Reserved) Write as 0.
MABACTL (MA[12:0] and BA[1:0] Drive Strength). 11 is strongest, 00 is weakest.
RSVD (Reserved). Write as 0.
25:24
MEMCTL (RASA#, CASA#, WEA#, CS[1:0]#, CKEA, DQM[7:0] Drive Strength). 11 is strongest, 00 is weakest.
23:22
RSVD (Reserved). Write as 0.
21
20:18
RSVD (Reserved). Must be written as 0. Wait state on the X-Bus x_data during read cycles - for debug only.
SDCLKRATE (SDRAM Clock Ratio). Selects SDRAM clock ratio.
000: Reserved
001: ÷ 2
010: ÷ 2.5
011: ÷ 3 (Default)
100: ÷ 3.5
101: ÷ 4
110: ÷ 4.5
111: ÷ 5
Ratio does not take effect until the SDCLKSTRT bit (bit 17 of this register) transitions from 0 to 1.
17
SDCLKSTRT (Start SDCLK). Start operating SDCLK using the new ratio and shift value (selected in bits [20:18] of this register).
0: Clear.
1: Enable.
This bit must transition from zero (written to zero) to one (written to one) in order to start SDCLK or to change the shift value.
16:8
RFSHRATE (Refresh Interval). This field determines the number of processor core clocks multiplied by 64 between refresh
cycles to the DRAM. By default, the refresh interval is 00h. Refresh is turned off by default.
7:6
RFSHSTAG (Refresh Staggering). This field determines number of clocks between the RFSH commands to each of the
four banks during refresh cycles:
00: 0 SDRAM clocks
01: 1 SDRAM clocks (Default)
10: 2 SDRAM clocks
11: 4 SDRAM clocks
Staggering is used to help reduce power spikes during refresh by refreshing one bank at a time. If only one bank is installed,
this field must be written as 00.
5
2CLKADDR (Two Clock Address Setup). Assert memory address for one extra clock before CS# is asserted.
0: Disable.
1: Enable.
This can be used to compensate for address setup at high frequencies and/or high loads.
18
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Architecture Overview
Table 2-2. SC3200 Memory Controller Registers (Continued)
Bit
Description
4
RFSHTST (Test Refresh). This bit, when set high, generates a refresh request. This bit is only used for testing purposes.
3
XBUSARB (X-Bus Round Robin). When round robin is enabled, processor, graphics pipeline, and low priority display controller requests are arbitrated at the same priority level. When disabled, processor requests are arbitrated at a higher priority
level. High priority Display Controller requests always have the highest arbitration priority.
0: Disable.
1: Enable round robin.
2
SMM_MAP (SMM Region Mapping). Maps the SMM memory region at GX_BASE+400000 to physical address A0000 to
BFFFF in SDRAM.
0: Disable.
1: Enable.
1
RSVD (Reserved). Write as 0.
0
SDRAMPRG (Program SDRAM). When this bit is set, the memory controller will program the SDRAM MRS register using
LTMODE in MC_SYNC_TIM1.
This bit must transition from zero (written to zero) to one (written to one) in order to program the SDRAM devices.
GX_BASE+8404h-8407h
MC_MEM_CNTRL2 (R/W)
Reset Value: 00000801h
31:14
RSVD (Reserved). Write as 0.
13:12
SDCLKCTL (SDCLK High Drive/Slew Control). Controls the high drive and slew rate of SDCLK[3:0] and SDCLK_OUT.
11 is strongest, 00 is weakest.
11
RSVD (Reserved). Write as 0.
10
SDCLKOMSK# (Enable SDCLK_OUT). Turns on the output.
0: Enable.
1: Disable.
9
SDCLK3MSK# (Enable SDCLK3). Turns on the output.
0: Enable.
1: Disable.
8
SDCLK2MSK# (Enable SDCLK2). Turns on the output.
0: Enable.
1: Disable.
7
SDCLK1MSK# (Enable SDCLK1). Turns on the output. 0
0: Enable.
1: Disable.
6
SDCLK0MSK# (Enable SDCLK0). Turns on the output.
0: Enable.
1: Disable.
5:3
SHFTSDCLK (Shift SDCLK). This function allows shifting SDCLK to meet SDRAM setup and hold time requirements. The
shift function will not take effect until the SDCLKSTRT bit (bit 17 of MC_MEM_CNTRL1) transitions from 0 to 1:
000: No shift
001: Shift 0.5 core clock
010: Shift 1 core clock
011: Shift 1.5 core clock
100: Shift 2 core clocks
101: Shift 2.5 core clocks
110: Shift 3 core clocks
111: Reserved
2
RSVD (Reserved). Write as 0.
1
RD (Read Data Phase). Selects if read data is latched one or two core clock after the rising edge of SDCLK.
0: 1 Core clock.
1: 2 Core clocks.
0
FSTRDMSK (Fast Read Mask). Do not allow core reads to bypass the request FIFO.
0: Disable.
1: Enable.
AMD Geode™ SC3200 Processor Data Book
19
Revision 5.1
Architecture Overview
Table 2-2. SC3200 Memory Controller Registers (Continued)
Bit
Description
GX_BASE+8408h-840Bh
31:16
MC_BANK_CFG (R/W)
Reset Value: 41104110h
RSVD (Reserved). Write as 0070h
15
RSVD (Reserved). Write as 0.
14
SODIMM_MOD_BNK (SODIMM Module Banks - Banks 0 and 1). Selects number of module banks installed per SODIMM
for SODIMM:
0: 1 Module bank (Bank 0 only)
1: 2 Module banks (Bank 0 and 1)
13
RSVD (Reserved). Write as 0.
12
SODIMM_COMP_BNK (SODIMM Component Banks - Banks 0 and 1). Selects the number of component banks per
module bank for SODIMM:
0: 2 Component banks
1: 4 Component banks
Banks 0 and 1 must have the same number of component banks.
11
10:8
RSVD (Reserved). Write as 0.
SODIMM_SZ (SODIMM Size - Banks 0 and 1). Selects the size of SODIMM:
000: 4 MB
001: 8 MB
010: 16 MB
011: 32 MB
100: 64 MB
101: 128 MB
110: 256 MB
111: 512 MB
This size is the total of both banks 0 and 1. Also, banks 0 and 1 must be the same size.
7
6:4
RSVD (Reserved). Write as 0.
SODIMM_PG_SZ (SODIMM Page Size - Banks 0 and 1). Selects the page size of SODIMM:
000: 1 KB
001: 2 KB
010: 4 KB
011: 8 KB
1xx: 16 KB
111: SODIMM not installed
Both banks 0 and 1 must have the same page size.
3:0
RSVD (Reserved). Write as 0.
GX_BASE+840Ch-840Fh
31
30:28
MC_SYNC_TIM1 (R/W)
Reset Value: 2A733225h
RSVD (Reserved). Write as 0.
LTMODE (CAS Latency). CAS latency is the delay, in SDRAM clock cycles, between the registration of a read command
and the availability of the first piece of output data. This parameter significantly affects system performance. Optimal setting
should be used. If an SODIMM is used, BIOS can interrogate EEPROM across the ACCESS.bus interface to determine this
value:
000: Reserved
001: Reserved
010: 2 CLK
011: 3 CLK
100: 4 CLK
101: 5 CLK
110: 6 CLK
111: 7 CLK
This field will not take effect until SDRAMPRG (bit 0 of MC_MEM_CNTRL1) transitions from 0 to 1.
27:24
RC (RFSH to RFSH/ACT Command Period, tRC). Minimum number of SDRAM clock between RFSH and RFSH/ACT
commands:
0000: Reserved
0001: 2 CLK
0010: 3 CLK
0011: 4 CLK
23:20
18:16
15
0100: 5 CLK
0101: 6 CLK
0110: 7 CLK
0111: 8 CLK
1000: 9 CLK
1001: 10 CLK
1010: 11 CLK
1011: 12 CLK
1100: 13 CLK
1101: 14 CLK
1110: 15 CLK
1111: 16 CLK
RP (PRE to ACT Command Period, tRP). Minimum number of SDRAM clocks between PRE and ACT commands:
010: 2 CLK
011: 3 CLK
100: 4 CLK
101: 5 CLK
110: 6 CLK
111: 7 CLK
RSVD (Reserved). Write as 0.
RCD (Delay Time ACT to READ/WRT Command, tRCD). Minimum number of SDRAM clock between ACT and READ/
WRT commands. This parameter significantly affects system performance. Optimal setting should be used:
000: Reserved
001: 1 CLK
20
1100: 13 CLK
1101: 14 CLK
1110: 15 CLK
1111: 16 CLK
RSVD (Reserved). Write as 0.
000: Reserved
001: 1 CLK
14:12
1000: 9 CLK
1001: 10 CLK
1010: 11 CLK
1011: 12 CLK
RAS (ACT to PRE Command Period, tRAS). Minimum number of SDRAM clocks between ACT and PRE commands:
0000: Reserved
0001: 2 CLK
0010: 3 CLK
0011: 4 CLK
19
0100: 5 CLK
0101: 6 CLK
0110: 7 CLK
0111: 8 CLK
010: 2 CLK
011: 3 CLK
100: 4 CLK
101: 5 CLK
110: 6 CLK
111: 7 CLK
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Architecture Overview
Table 2-2. SC3200 Memory Controller Registers (Continued)
Bit
Description
11
RSVD (Reserved). Write as 0.
10:8
7
6:4
RRD (ACT(0) to ACT(1) Command Period, tRRD). Minimum number of SDRAM clocks between ACT and ACT command
to two different component banks within the same module bank. The memory controller does not perform back-to-back Activate commands to two different component banks without a READ or WRITE command between them. Hence, this field
should be written as 001.
RSVD (Reserved). Write as 0.
DPL (Data-in to PRE command period, tDPL). Minimum number of SDRAM clocks from the time the last write datum is
sampled till the bank is precharged:
000: Reserved
001: 1 CLK
3:0
Note:
010: 2 CLK
011: 3 CLK
100: 4 CLK
101: 5 CLK
110: 6 CLK
111: 7 CLK
RSVD (Reserved). Leave unchanged. Always returns a 101h.
Refer to the SDRAM manufacturer’s specification for more information on component banks.
GX_BASE+8414h-8417h
31:18
RSVD (Reserved). Write as 0.
17
TE (Test Enable TEST[3:0]).
MC_GBASE_ADD (R/W)
Reset Value: 00000000h
0: TEST[3:0] are driven low (normal operation).
1: TEST[3:0] pins are used to output test information
16
TECTL (Test Enable Shared Control Pins).
0: RASB#, CASB#, CKEB, WEB# (normal operation).
1: RASB#, CASB#, CKEB, WEB# are used to output test information
15:12
11
10:0
SEL (Select). This field is used for debug purposes only and should be left at zero for normal operation.
RSVD (Reserved). Write as 0.
GBADD (Graphics Base Address). This field indicates the graphics memory base address, which is programmable on 512
KB boundaries. This field corresponds to address bits [29:19].
Note that BC_DRAM_TOP must be set to a value lower than the Graphics Base Address.
GX_BASE+8418h-841Bh
31:10
9:0
Reset Value: 00000000h
RSVD (Reserved). Write as 0.
DRADD (Dirty RAM Address). This field is the address index that is used to access the Dirty RAM with the MC_DR_ACC
register. This field does not auto increment.
GX_BASE+841Ch-841Fh
31:2
MC_DR_ADD (R/W)
MC_DR_ACC (R/W)
Reset Value: 0000000xh
RSVD (Reserved). Write as 0.
1
D (Dirty Bit). This bit is read/write accessible.
0
V (Valid Bit). This bit is read/write accessible.
AMD Geode™ SC3200 Processor Data Book
21
Revision 5.1
2.1.2
Fast-PCI Bus
The GX1 module communicates with the Core Logic module via a Fast-PCI bus that can work at up to 66 MHz. The
Fast-PCI bus is internal for the SC3200 and is connected
to the General Configuration Block (see Section 4.0 on
page 87 for details on the General Configuration Block).
This bus supports seven bus masters. The requests
(REQs) are fixed in priority. The seven bus masters in order
of priority are:
2.2.1
VIP
2)
IDE Channel 0
3)
IDE Channel 1
4)
Audio
5)
USB
6)
External REQ0#
7)
External REQ1#
Display
GX1 Module Interface
The Video Processor is connected to the GX1 module in
the following way:
• The Video Processor’s DOTCLK output signal is used as
the GX1 module’s DCLK input signal.
• The GX1 module’s PCLK output signal is used as the
GFXCLK input signal of the Video Processor.
2.2.2
1)
2.1.3
Architecture Overview
Video Input Port
The Video Input Port (VIP) within the Video Processor contains a standard interface that is typically connected to a
media processor or TV encoder. The clock is supplied by
the externally connected device; typically at 27 MHz.
Video input can be sent to the GX1 module’s video frame
buffer (Capture Video mode) or can be used directly (Direct
Video mode).
2.2.3
Core Logic Module Interface
The Video Processor interfaces to the Core Logic module
for accessing PCI function configuration registers.
The GX1 module generates display timing, and controls
internal VSYNC and HSYNC signals of the Video Processor module.
2.3
The GX1 module interfaces with the Video Processor via a
video data bus and a graphics data bus.
The Core Logic module is described in detail in Section 6.0
"Core Logic Module" on page 157.
• Video data. The GX1 module uses the core clock,
divided by 2 or 4 (typically 100 - 133 MHz). It drives the
video data using this clock. Internal signals VID_VAL
and VID_RDY are used as data-flow handshake signals
between the GX1 module and the Video Processor.
The Core Logic module is connected to the Fast-PCI bus. It
uses signal AD28 as the IDSEL for all PCI configuration
functions except for USB which uses AD29.
• Graphics data. The GX1 module uses the internal
signal DCLK, supplied by the PLL of the Video
Processor, to drive the 18-bit graphics-data bus of the
Video Processor. Each six bits of this bus define a
different color. Each of these 6-bit color definitions is
expanded (by adding two zero LSB lines) to form an 8bit bus, at the Video Processor.
The following interfaces of the Core Logic module are
implemented via external balls of the SC3200. Each interface is listed below with a reference to the descriptions of
the relevant balls.
For more information about the GX1 module’s interface to
the Video Processor, see the “Display Controller” chapter
in the AMD Geode™ GX1 Processor Data Book.
2.2
Video Processor Module
The Video Processor provides high resolution and graphics
for a TFT/DSTN interface. The following subsections provide a summary of how the Video Processor interfaces with
the other modules of the SC3200. For detailed information
about the Video Processor, see Section 7.0 "Video Processor Module" on page 327.
22
2.3.1
Core Logic Module
Other Core Logic Module Interfaces
• IDE: See Section 3.4.9 "IDE Interface Signals" on page
75.
• AC97: See Section 3.4.14 "AC97 Audio Interface
Signals" on page 80.
• PCI: See Section 3.4.6 "PCI Bus Interface Signals" on
page 68.
• USB: See Section 3.4.10 "Universal Serial Bus (USB)
Interface Signals" on page 76. The USB function uses
signal AD29 as the IDSEL for PCI configuration.
• LPC: See Section 3.4.8 "Low Pin Count (LPC) Bus Interface Signals" on page 74.
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Architecture Overview
• Sub-ISA: See Section 3.4.7 "Sub-ISA Interface Signals"
on page 73, Section 6.2.5 "Sub-ISA Bus Interface" on
page 163, and Section 4.2 "Multiplexing, Interrupt Selection, and Base Address Registers" on page 88
• GPIO: See Section 3.4.16 "GPIO Interface Signals" on
page 82.
• More detailed information about each of these interfaces
is provided in Section 6.2 "Module Architecture" on page
158.
• Super/IO Block Interfaces: See Section 4.2 "Multiplexing, Interrupt Selection, and Base Address Registers" on page 88, Section 3.4.5 "ACCESS.bus Interface
Signals" on page 67, Section 3.4.13 "Fast Infrared (IR)
Port Interface Signals" on page 79, and Section 3.4.12
"Parallel Port Interface Signals" on page 78.
The Core Logic module interface to the GX1 module consists of seven miscellaneous connections, the PCI bus
interface signals, plus the display controller connections.
Note that the PC/AT legacy signals NMI, WM_RST, and
A20M are all virtual functions executed in SMM (System
Management Mode) by the BIOS.
• PSERIAL is a one-way serial bus from the GX1 to the
Core Logic module used to communicate powermanagement states and VSYNC information for VGA
emulation.
• IRQ13 is an input from the GX1 module indicating that a
floating point error was detected and that INTR should
be asserted.
• INTR is the level output from the integrated 8259A PICs
and is asserted if an unmasked interrupt request (IRQn)
is sampled active.
• SMI# is a level-sensitive interrupt to the GX1 module
that can be configured to assert on a number of different
system events. After an SMI# assertion, SMM is entered
and program execution begins at the base of the SMM
address space. Once asserted, SMI# remains active
until the SMI source is cleared.
• SUSP# and SUSPA# are handshake signals for implementing CPU Clock Stop and clock throttling.
• CPU_RST resets the CPU and is asserted for approximately 100 µs after the negation of POR#.
• PCI bus interface signals.
The SIO module incorporates: two Serial Ports, an Infrared
Communication Port that supports FIR, MIR, HP-SIR,
Sharp-IR, and Consumer Electronics-IR, a full IEEE 1284
Parallel Port, two ACCESS.bus Interface (ACB) ports, System Wakeup Control (SWC), and a Real-Time Clock (RTC)
that provides RTC timekeeping.
2.5
Clock, Timers, and Reset Logic
In addition to the four main modules (i.e., GX1, Core Logic,
Video Processor and SIO) that make up the SC3200, the
following blocks of logic have also been integrated into the
SC3200:
• Clock Generators as described in Section 4.5 "Clock
Generators and PLLs" on page 99.
• Configuration Registers as described in Section 4.2
"Multiplexing, Interrupt Selection, and Base Address
Registers" on page 88.
• A WATCHDOG timer as described in Section 4.3
"WATCHDOG" on page 95.
• A High-Resolution timer as described in Section 4.4
"High-Resolution Timer" on page 97.
2.5.1
Reset Logic
This section provides a description of the reset flow of the
SC3200.
2.5.1.1 Power-On Reset
Power-on reset is triggered by assertion of the POR# signal. Upon power-on reset, the following things happen:
• Strap balls are sampled.
• PLL4, PLL5, and PLL6 are reset, disabling their output.
When the POR# signal is negated, the clocks lock and
then each PLL outputs its clock. PLL6 is the last clock
generator to output a clock. See Section 4.5 "Clock
Generators and PLLs" on page 99.
• Certain WATCHDOG and High-Resolution Timer
register bits are cleared.
2.5.1.2 System Reset
System reset causes signal PCIRST# to be issued, thus
triggering a reset of all PCI and LPC agents. A system
reset is triggered by any of the following events:
• Power-on, as indicated by POR# signal assertion.
2.4
Super I/O Module
The SuperI/O (SIO) module is a PC98 and ACPI compliant
SIO that offers a single-cell solution to the most commonly
used ISA peripherals.
AMD Geode™ SC3200 Processor Data Book
• A WATCHDOG reset event (see Section 4.3.2
"WATCHDOG Registers" on page 96).
• Software initiated system reset.
23
Revision 5.1
24
Architecture Overview
AMD Geode™ SC3200 Processor Data Book
Signal Definitions
Revision 5.1
3
3.0Signal Definitions
This section defines the signals and describes the external
interface of the SC3200. Figure 2-1 shows the signals
organized by their functional groups. Where signals are
multiplexed, the default signal name is listed first and is
System
Interface
POR#
X32I
X32O
X27I
X27O
PCIRST#
BOOT16+ROMCS#
LPC_ROM+PCICLK1
TFT_PRSNT+SDATA_OUT
FPCI_MON+PCICLK0
DID0+GNT0#, DID1+GNT1#
separated by a plus sign (+). A slash (/) in a signal name
means that the function is always enabled and available
(i.e., cycle multiplexed).
MD[63:0]
Memory
Interface
MA[12:0]
BA[1:0]
CS[1:0]#
RASA#
CASA#
WEA#
DQM[7:0]
CKEA
SDCLK[3:0]
SDCLK_IN
SDCLK_OUT
AMD Geode™
SC3200
Processor
ACCESS.bus
Interface
AB1C+GPIO20+DOCCS#
AB1D+GPIO1+IOCS1#
GPIO12+AB2C
GPIO13+AB2D
Parallel Port/
TFT Interface
ACK#+TFTDE
AFD#/DSTRB#+TFTD2
BUSY/WAIT#+TFTD3
ERR#+TFTD4
INIT#+TFTD5
PD7+TFTD13
PD6+TFTD1
PD[5:0]+TFTD[11:6]
PE+TFTD14
SLCT+TFTD15
SLIN#/ASTRB#+TFTD16
STB#/WRITE#+TFTD17
Video Port
Interface
Note:
IDE_ADDR2+TFTD4
IDE_ADDR1+TFTD2
IDE_ADDR0+TFTD3
IDE_DATA15+TFTD7
IDE_DATA14+TFTD17
IDE_DATA13+TFTD15
IDE_DATA12+TFTD13
IDE_DATA11+GPIO41
IDE_DATA10
IDE_DATA9
IDE_DATA8+GPIO40
IDE_DATA7+INTD#
IDE_DATA6+IRQ9
IDE_DATA5+CLK27M
IDE_DATA4+FP_VDD_ON
IDE_DATA3+TFTD12
IDE_DATA2+TFTD14
IDE_DATA1+TFTD16
IDE_DATA0+TFTD6
IDE_IOR0#+TFTD10
IDE_IOW0#+TFTD9
IDE_CS0#+TFTD5
IDE_CS1#+TFTDE
IDE_IORDY0+TFTD11
IDE_DREQ0+TFTD8
IDE_DACK0#+TFTD0
IDE_RST#+TFTDCK
IRQ14+TFTD1
Straps
IDE/TFT
Interface
VPD[7:0]
VPCKIN
Straps are not the default signal, shown with system signals for reader convenience. However, also listed in figure with the
appropriate functional group.
Figure 3-1. Signal Groups
AMD Geode™ SC3200 Processor Data Book
25
Revision 5.1
USB
Interface
Serial Ports
(UARTs)/IDE
Interface
IR Port
Interface
AC97 Audio
Interface
Power
Management
Interface
JTAG
Interface
Signal Definitions
POWER_EN
OVER_CUR#
DPOS_PORT1
DNEG_PORT1
DPOS_PORT2
DNEG_PORT2
DPOS_PORT3
DNEG_PORT3
PCICLK0+FPCI_MON
PCICLK1+LPC_ROM
PCICLK
INTA#, INTB#
FRAME#
AMD Geode™
LOCK#
SC3200
PERR#
Processor
SERR#
REQ[1:0]#
GNT0#+DID0
SIN1
GNT1#+DID1
SIN2+SDTEST3
A[23:0]/AD[23:0]
SOUT1+CLKSEL1
D[7:0]/AD[31:24]
SOUT2+CLKSEL2
D[11:8]/C/BE[3:0]#
GPIO7+RTS2#+IDE_DACK1#+SDTEST0
D12/PAR
GPIO8+CTS2#+IDE_DREQ1+SDTEST4
D13/TRDY#
GPIO18+DTR1#/BOUT1
D14/IRDY#
GPIO6+DTR2#/BOUT2+IDE_IOR1#+SDTEST5
D15/STOP#
GPIO11+RI2#+IRQ15
BHE#/DEVSEL#
GPIO9+DCD2#+IDE_IOW1#+SDTEST2
GPIO17+TFTDCK+IOCS0#
GPIO10+DSR2#+IDE_IORDY1+SDTEST1
GPIO1+IOCS1+TFTD12
ROMCS#/BOOT16
GPIO20+DOCCS#+TFTD0
IRRX1+SIN3
RD#+CLKSEL0
IRTX+SOUT3
WR#
GPIO14+DOCR#+IOR#
BIT_CLK
GPIO15+DOCW#+IOW#
SDATA_OUT+TFT_PRSNT
GPIO0+TRDE#
SDATA_IN
GPIO19+INTC#+IOCHRDY
SDATA_IN2
SYNC+CLKSEL3
AC97_CLK
GPIO32+LAD0
AC97_RST#
GPIO33+LAD1
GPIO16+PC_BEEP
GPIO34+LAD2
GPIO35+LAD3
GPIO36+LDRQ#
CLK32
GPIO37+LFRAME#
GPWIO[2:0]
GPIO38+IRRX2+LPCPD
LED#
GPIO39+SERIRQ
ONCTL#
PWRBTN#
PWRCNT[1:2]
TEST1+PLL6B
TEST0+PLL2B
THRM#
GXCLK+FP_VDD_ON+TEST3
TEST2+PLL5B
TCK
GTEST
TDI
TDP, TDN
TDO
TMS
TRST#
Figure 3-1.
Sub-ISA/PCI Bus
Interface
GPIO/LPC Bus
Interface
Test and
Measurement
Interface
Signal Groups (Continued)
The remaining subsections of this chapter describe:
• Section 3.1 "Ball Assignments": Provides a ball assignment diagram and tables listing the signals sorted
according to ball number and alphabetically by signal
name.
• Section 3.3 "Multiplexing Configuration": Lists multiplexing options and their configurations.
• Section 3.4 "Signal Descriptions": Detailed descriptions
of each signal according to functional group.
• Section 3.2 "Strap Options": Several balls are read at
power-up that set up the state of the SC3200. This
section provides details regarding those balls.
26
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
3.1
Ball Assignments
The SC3200 is highly configurable as illustrated in Figure
3-1 on page 25. Strap options and register programming
are used to set various modes of operation and specific
signals on specific balls. This section describes which signals are available on which balls and provides configuration
information:
• Figure 3-2 on page 28 and Figure 3-3 on page 42: Illustrations of EBGA and TEPBGA ball assignments.
• Table 3-2 on page 29 and Table 3-4 on page 43: Lists
signals according to ball number. Power Rail, Signal
Type, Buffer Type and, where relevant, Pull-Up or PullDown resistors are indicated for each ball in this table.
For multiplexed balls, the necessary configuration for
each signal is listed as well.
• Table 3-3 on page 38 and Table 3-5 on page 54: Quick
reference signal list sorted alphabetically - listing all
signal names and ball numbers.The tables in this
chapter use several common abbreviations. Table 3-1
lists the mnemonics and their meanings
Table 3-1. Signal Definitions Legend
Mnemonic
Definition
A
Analog
AVSS
Ground ball: Analog
AVCC
Power ball: Analog
GCB
General Configuration Block registers.
Refer to Section 4.0 "General Configuration Block" on page 87.
Location of the General Configuration
Block cannot be determined by software.
See the AMD Geode™ SC3200 Specification Update document.
I
Input ball
I/O
Bidirectional ball
MCR[x]
Miscellaneous Configuration Register
Bit x: A register, located in the GCB.
Refer to Section 4.1 "Configuration
Block Addresses" on page 87 for further
details.
O
Output ball
OD
Open-drain
PD
Pull-down
PMR[x]
Pin Multiplexing Register Bit x: A register, located in the GCB, used to configure balls with multiple functions. Refer to
Section 4.1 "Configuration Block
Addresses" on page 87 for further
details.
PU
Pull-up
TS
TRI-STATE
VCORE
Power ball: 1.2V
VIO
Power ball: 3.3V
VSS
Ground ball
#
The # symbol in a signal name indicates
that the active or asserted state occurs
when the signal is at a low voltage level.
Otherwise, the signal is asserted when
at a high voltage level.
/
A / in a signal name indicates both functions are always enabled (i.e., cycle multiplexed).
+
A + in signal name indicates the function
is available on the ball, but that either
strapping options or register programming is required to select the desired
function.
Notes:
1)
For each GPIO signal, there is an optional pull-up
resistor on the relevant ball. After system reset, the
pull-up is present.
This pull-up resistor can be disabled via registers in
the Core Logic module. The configuration is without
regard to the selected ball function (except for
GPIO12, GPIO13, and GPIO16). Alternate functions
for GPIO12, GPIO13, and GPIO16 control pull-up
resistors.
For more information, see Section 6.4.1 "Bridge,
GPIO, and LPC Registers - Function 0" on page 206.
2)
Configuration settings listed in this table are with
regard to the Pin Multiplexing Register (PMR). See
Section 4.2 "Multiplexing, Interrupt Selection, and
Base Address Registers" on page 88 for a detailed
description of this register.
AMD Geode™ SC3200 Processor Data Book
27
Revision 5.1
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
W
Y
AA
AB
AC
AD
AE
AF
AG
AH
AJ
AK
AL
1
2
VSS
VIO
3
4
5
6
7
8
Signal Definitions
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
AD29 AD26 AD22 AD19 AD16 CBE3# SERR# CBE1# AD14 AD12 CBE0# AD5
AD3
AD4
AD0
AD2 IDAT13 IDAT10 IDAT8 IRST# IDAT5 IDAT1 IORDY0 IAD0 ICS0# GP18
X27I
VIO
VSS
VSS SOUT1 PWRE TEST2 VSS
VIO
S
VIO
VSS
RQ0# AD30
S
AD31 AD27 DVSL#
VIO
S
VIO
VSS TRDY# PERR# AD15
AD28 AD24 AD21 AD17 IRDY# LOCK# PAR
VIO
VSS
AD9
AD7
VSS
VIO
VSS IDAT15 IDAT12 VIO
VSS
IDAT7 IDAT4 IDAT0
VIO
AD13 AD11 AD10
AD8
AD6 ICS1# IAD2 IDAT14 IDAT11 IDAT9 IIOR0# IDAT6 IDAT3 IDRQ0 IDCK0# IAD1 OVCR# TEST1
VIO
X32I
VPLL3
IDAT2 IIOW0# IRQ14 SIN1 X27O TEST0 X32O VBAT
LED#
S
PRST# GNT1# PCK0 GNT0# AD25 AD20 AD18 CBE2# STP#
VSS VCORE VSS VCORE VSS VCORE AD1 VCORE VSS
VCORE VSS VCORE VSS
S
FRM# PCLK REQ1# PCK1
AVSSP3 PBTN# OCTL# GPW0
S
IOR#
VSS
RD#
AD23
THRM# VSB
VSS PCNT1
GPW1 GPW2
VIO PCNT2
S
WR#
VIO
TRDE# GP1
IOW# RMCS#
VSBL CK32 GP11 SDIN2
GP20 GP19
IRRX1 POR# MD0
HSYN VSYN IRTX GP17
NC
VSS
VIO
VIO
NC
VSS VCORE VSS
VSS
VIO
VCORE
VIO
NC
VSS
VSS
VCORE
VSS
VSS
NC
NC
VPLL2
VSS AVSSP2 VCORE
BSY
VIO
PD7
VSS
ACK# VCORE
PD4
PD5
PD6
SLIN# PD3
PE
AMD Geode™
SC3200
Processor
PD2 VCORE
INIT#
PD0
VSS
ERR# VCORE
VSS
MD4
VCORE MD5
VSS
MD6
VIO
DQM0
VSS
MD7
CS0#
BA0
BA1
VCORE MA10
VSS
MA0
DQM4 MA2 VCORE MA1
VCORE MD33
VSS
VSS
MD32
MD36 MD35 MD34
VCORE MD39 MD38 MD37
VSS
VSS
NC
MD3
VCORE WEA# CASA# RASA#
VSS
VIO
MD2
VSS
SLCT
PD1
STB# AFD#
VSS
MD1
MD46
VIO
MD47
VCORE MD44
VSS
MD45
VSS
MD41 MD42 MD43
NC
NC
VIO
VSS
CKEA SDCK0 DQM5 MD40
NC
NC
NC
NC
MA6
MA7
MA8
MA9
NC
VIO
INTA# D+P3
MA3
MA4
VIO
MA5
INTB#
VSS
D-P3 AVCCUSB
MD14 MD15
VSS
DQM1
MA11 MD9
MD8 MD13
(Top View)
AVSSUSB D-P2 D-P1
GP9
D+P2 D+P1
GP6
GP7
TDP
GP10
VIO
SIN2
TMS VPD7 VPD6 VPD2 GP38 GP35 GP32 GP12 AB1C ACCK ACRT# SDCK3 MD56 MD58 MD61 DQM7 DQM3 MD25 MD29 MD54 MD50 DQM6 MD22 MD19
GP8
TDO VPCKI VPD4 VPD0
VSS VCORE VSS VCORE VSS VCORE SDCK1 VCORE VSS VCORE VSS VCORE VSS
S
VIO
MD28 MD55 MD51 MD48 MD23 SDCKO MA12 MD11 MD10
VIO
SDCKI MD12
S
VSS SOUT2 TRST# TDI
VIO
VSS
VPD1 GP37 GP34
VIO
VSS SDATO SDATI
VSS
VIO
VSS
MD59 MD62
VIO
VSS
MD26 MD30 MD53
VIO
VSS
MD21 MD18 CS1#
VSS
VIO
TCK GTST VPD5 VPD3 GP39 GP36 GP33 GP13 AB1D SYNC BITCK GP16 GXCK MD57 MD60 MD63 SDCK2 MD24 MD27 MD31 MD52 MD49 DQM2 MD20 MD17 MD16
VIO
VSS
S
VSS
VIO
TDN
1
2
3
Note:
4
5
6
7
8
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
W
Y
AA
AB
AC
AD
AE
AF
AG
AH
AJ
AK
AL
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
Signal names have been abbreviated in this figure due to space constraints.
= GND Ball
= PWR Ball
S
= Strap Option Ball
= Multiplexed Ball
Figure 3-2. 432-EBGA Ball Assignment Diagram
28
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
Table 3-2. 432-EBGA Ball Assignment - Sorted by Ball Number
I/O
(PU/
PD)
Buffer1
Type
Power
Rail Configuration
Ball
No.
Signal Name
A1
VSS
GND
---
---
---
A2
VIO
PWR
---
---
---
A3
AD29
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
A4
A5
A6
A7
D5
I/O
INPCI,
OPCI
AD26
I/O
INPCI,
OPCI
D2
I/O
INPCI,
OPCI
AD22
I/O
INPCI,
OPCI
A22
O
OPCI
AD19
I/O
INPCI,
OPCI
A19
O
OPCI
AD16
I/O
INPCI,
OPCI
A16
A8
C/BE3#
D11
A9
A10
SERR#
C/BE1#
D9
A11
A12
A13
A14
A15
A16
A17
AD14
O
OPCI
I/O
(PU22.5)
INPCI,
OPCI
I/O
(PU22.5)
INPCI,
OPCI
VIO
Cycle Multiplexed
VIO
Cycle Multiplexed
VIO
VIO
INPCI,
OPCI
VIO
I/O
(PU22.5)
INPCI,
OPCI
I/O
INPCI,
OPCI
OPCI
INPCI,
OPCI
A12
O
OPCI
C/BE0#
I/O
(PU22.5)
INPCI,
OPCI
D8
I/O
(PU22.5)
INPCI,
OPCI
AD5
I/O
INPCI,
OPCI
A5
O
OPCI
AD3
I/O
INPCI,
OPCI
A3
O
OPCI
AD4
I/O
INPCI,
OPCI
A4
O
OPCI
AD0
I/O
INPCI,
OPCI
A0
O
OPCI
AD2
Cycle Multiplexed
VIO
Cycle Multiplexed
VIO
VIO
Cycle Multiplexed
VIO
Cycle Multiplexed
OPCI
I/O
INTS1,
TS1/4
AMD Geode™ SC3200 Processor Data Book
PMR[24] = 1
VIO
PMR[24] = 0
A21
IDE_DATA8
I/O
INTS1,
TS1/4
VIO
PMR[24] = 0
GPIO40
I/O
INTS1,
O1/4
IDE_RST#
O
O1/4
TFTDCK
O
O1/4
IDE_DATA5
I/O
INTS1,
TS1/4
CLK27M
O
O1/4
A24
IDE_DATA1
I/O
INTS1,
TS1/4
TFTD16
O
O1/4
A25
IDE_IORDY0
I
INTS1
A26
A27
TFTD11
O
O1/4
IDE_ADDR0
O
O1/4
TFTD3
O
O1/4
IDE_CS0#
O
O1/4
TFTD5
O
O1/4
GPIO18
INTS, O8/
I/O
(PU22.5)
8
DTR1#/BOUT1
O
(PU22.5)
O8/8
PMR[24] = 1
VIO
PMR[24] = 0
PMR[24] = 1
VIO
PMR[24] = 0
PMR[24] = 1
VIO
PMR[24] = 0
PMR[24] = 1
VIO
PMR[24] = 0
PMR[24] = 1
VIO
PMR[24] = 0
PMR[24] = 1
VIO
PMR[24] = 0
PMR[24] = 1
VIO
PMR[16] = 0
PMR[16] =1
A29
X27I
I
WIRE
VIO
---
A30
VIO
PWR
---
---
---
A31
VSS
GND
---
---
---
B1
VIO
PWR
---
---
---
B2
VSS
GND
---
---
---
B3
AD31
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
D7
I/O
INPCI,
OPCI
AD27
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
D3
I/O
INPCI,
OPCI
I/O
(PU22.5)
INPCI,
OPCI
VIO
Cycle Multiplexed
DEVSEL#
BHE#
Cycle Multiplexed
PMR[24] = 0
O1/4
B5
VIO
VIO
INTS1,
TS1/4
B4
Cycle Multiplexed
O
IDE_DATA13
Cycle Multiplexed
O
Cycle Multiplexed
VIO
A2
VIO
I/O
A28
VIO
INPCI,
OPCI
Power
Rail Configuration
IDE_DATA10
Cycle Multiplexed
Cycle Multiplexed
I/O
Buffer1
Type
TFTD15
Cycle Multiplexed
---
I/O
(PU/
PD)
A20
A23
I/O
(PU22.5)
O
A18
A22
VIO
I/O
Cycle Multiplexed
VIO
INPCI,
ODPCI
AD12
Signal Name
A19
I/O
(PU22.5)
A14
Ball
No.
O
OPCI
B6
VIO
PWR
---
---
---
B7
VSS
GND
---
---
---
B8
TRDY#
I/O
(PU22.5)
INPCI,
OPCI
VIO
Cycle Multiplexed
D13
I/O
(PU22.5)
INPCI,
OPCI
29
Revision 5.1
Table 3-2.
Signal Definitions
432-EBGA Ball Assignment - Sorted by Ball Number (Continued)
I/O
(PU/
PD)
Buffer1
Type
I/O
(PU22.5)
INPCI,
OPCI
VIO
---
AD15
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
A15
O
OPCI
Ball
No.
Signal Name
B9
PERR#
B10
Power
Rail Configuration
B11
VIO
PWR
---
---
---
VSS
GND
---
---
---
B13
AD9
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
VIO
Cycle Multiplexed
A9
O
OPCI
B14
AD7
I/O
INPCI,
OPCI
A7
O
OPCI
B15
VSS
GND
---
---
---
B16
VIO
PWR
---
---
---
B17
VSS
GND
---
---
---
B18
IDE_DATA15
I/O
INTS1,
TS1/4
VIO
PMR[24] = 0
TFTD7
O
O1/4
IDE_DATA12
I/O
INTS1,
TS1/4
TFTD13
O
O1/4
B19
PMR[24] = 0
VIO
PWR
---
---
---
B21
VSS
GND
---
---
---
B22
IDE_DATA7
I/O
INTS1,
TS1/4
VIO
PMR[24] = 0
I
INTS
IDE_DATA4
I/O
INTS1,
TS1/4
FP_VDD_ON
O
O1/4
IDE_DATA0
I/O
INTS1,
TS1/4
TFTD6
O
O1/4
B23
B24
D4
I/O
INPCI,
OPCI
AD24
I/O
INPCI,
OPCI
D0
I/O
INPCI,
OPCI
AD21
I/O
INPCI,
OPCI
A21
O
OPCI
AD17
I/O
INPCI,
OPCI
A17
O
OPCI
IRDY#
I/O
(PU22.5)
INPCI,
OPCI
D14
I/O
(PU22.5)
INPCI,
OPCI
C9
LOCK#
I/O
(PU22.5)
C10
PAR
D12
C6
C7
C8
C12
VIO
PMR[24] = 0
C13
VIO
PMR[24] = 0
C14
Cycle Multiplexed
VIO
Cycle Multiplexed
VIO
Cycle Multiplexed
VIO
Cycle Multiplexed
VIO
Cycle Multiplexed
INPCI,
OPCI
VIO
---
I/O
(PU22.5)
INPCI,
OPCI
VIO
Cycle Multiplexed
I/O
(PU22.5)
INPCI,
OPCI
AD13
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
A13
O
OPCI
AD11
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
A11
O
OPCI
AD10
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
A10
O
OPCI
AD8
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
A8
O
OPCI
AD6
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
A6
O
OPCI
VIO
PMR[24] = 0
PMR[24] = 1
PWR
---
---
---
VSS
GND
---
---
---
B27
SOUT1
O
O8/8
VIO
---
I
(PD100)
INSTRP
Strap (See Table
3-6 on page 58.)
B28
POWER_EN
O
O1/4
VIO
---
B29
TEST2
O
O2/5
VIO
PMR[29] = 1
PLL5B
I/O
INT, TS2/5
C15
C16
C17
PMR[29] = 0
B30
VSS
GND
---
---
---
B31
VIO
PWR
---
---
---
C1
REQ0#
I
(PU22.5)
INPCI
VIO
---
C2
AD30
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
D6
I/O
INPCI,
OPCI
VIO
PWR
---
C18
C19
C20
---
---
Power
Rail Configuration
VIO
PMR[24] = 1
VIO
30
INPCI,
OPCI
PMR[24] = 1
B26
C3
I/O
C11
B25
CLKSEL1
AD28
PMR[24] = 1
B20
INTD#
C4
PMR[24] = 1
VIO
Buffer1
Type
Signal Name
C5
B12
I/O
(PU/
PD)
Ball
No.
IDE_CS1#
O
O1/4
TFTDE
O
O1/4
IDE_ADDR2
O
O1/4
TFTD4
O
O1/4
IDE_DATA14
I/O
INTS1,
TS1/4
TFTD17
O
O1/4
IDE_DATA11
I/O
INTS1,
TS1/4
GPIO41
I/O
INTS1,
O1/4
IDE_DATA9
I/O
INTS1,
TS1/4
PMR[24] = 1
VIO
PMR[24] = 0
PMR[24] = 1
VIO
PMR[24] = 0
PMR[24] = 1
VIO
PMR[24] = 0
PMR[24] = 1
VIO
PMR[24] = 0
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
Table 3-2.
Ball
No.
C21
C22
Signal Name
C24
C25
I/O
(PU/
PD)
Buffer1
Type
IDE_IOR0#
O
O1/4
TFTD10
O
O1/4
IDE_DATA6
I/O
INTS1,
TS1/4
IRQ9
C23
432-EBGA Ball Assignment - Sorted by Ball Number (Continued)
I
INTS1
IDE_DATA3
I/O
INTS1,
TS1/4
TFTD12
O
O1/4
IDE_DREQ0
I
INTS1
TFTD8
O
O1/4
IDE_DACK0#
O
O1/4
Power
Rail Configuration
VIO
VIO
PMR[24] = 0
PMR[24] = 0
VIO
PMR[24] = 0
PMR[24] = 1
VIO
PMR[24] = 0
PMR[24] = 1
O
O1/4
O
O1/4
TFTD2
O
O1/4
C27
OVER_CUR#
I
INTS
VIO
---
C28
TEST1
O
O2/5
VIO
PMR[29] = 1
PLL6B
I/O
INTS,
TS2/5
VIO
PMR[24] = 0
PMR[24] = 1
PWR
---
---
---
C30
X32I
I
WIRE
VBAT
---
C31
VPLL3
PWR
---
---
---
D1
PCIRST#
O
OPCI
VIO
---
D2
GNT1#
O
OPCI
VIO
---
I
(PD100)
INSTRP
O
OPCI
I
(PD100)
INSTRP
O
OPCI
DID0
I
(PD100)
INSTRP
AD25
I/O
INPCI,
OPCI
FPCI_MON
D4
D5
GNT0#
D1
I/O
INPCI,
OPCI
D6
AD20
I/O
INPCI,
OPCI
A20
O
OPCI
D7
AD18
I/O
INPCI,
OPCI
O
OPCI
D8
C/BE2#
I/O
(PU22.5)
INPCI,
OPCI
D10
I/O
(PU22.5)
INPCI,
OPCI
STOP#
I/O
(PU22.5)
INPCI,
OPCI
D15
I/O
(PU22.5)
INPCI,
OPCI
VSS
GND
---
A18
D9
D10
---
---
---
GND
---
---
-----
Strap (See Table
3-6 on page 58.)
VIO
D13
VCORE
PWR
---
---
VSS
GND
---
---
---
D15
VCORE
PWR
---
---
---
D16
AD1
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
A1
O
OPCI
---
D17
VCORE
PWR
---
---
D18
VSS
GND
---
---
---
D19
VCORE
PWR
---
---
---
D20
VSS
GND
---
---
---
D21
VCORE
PWR
---
---
---
D22
VSS
GND
---
---
---
D23
IDE_DATA2
I/O
INTS1,
TS1/4
VIO
PMR[24] = 0
VIO
VIO
D25
TFTD14
O
O1/4
IDE_IOW0#
O
O1/4
TFTD9
O
O1/4
IRQ14
I
INTS1
TFTD1
O
O1/4
PMR[24] = 0
PMR[24] = 1
SIN1
I
INTS
VIO
---
D27
X27O
O
WIRE
VIO
---
D28
TEST0
O
O2/5
VIO
PMR[29] = 1
PLL2B
I/O
INT, TS2/5
D29
X32O
O
WIRE
VBAT
PMR[29] = 0
---
D30
VBAT
PWR
---
---
---
D31
LED#
O
OD14
VSB
---
E1
FRAME#
I/O
(PU22.5)
INPCI,
OPCI
VIO
---
Cycle Multiplexed
E2
PCICLK
I
INT
VIO
---
E3
REQ1#
I
(PU22.5)
INPCI
VIO
---
E4
PCICLK1
O
OPCI
VIO
---
I
(PD100)
INSTRP
VIO
Cycle Multiplexed
VIO
Cycle Multiplexed
LPC_ROM
E28
AVSSPLL3
E29
PWRBTN#
E303, 4 ONCTL#
---
---
---
---
I
(PU100)
INBTN
VSB
---
OD14
VSB
---
INTS,
TS2/14
VSB
---
IOR#
O
O3/5
VIO
PMR[21] = 0 and
PMR[2] = 0
DOCR#
O
O3/5
F1
F2
GND
O
GPWIO0
Cycle Multiplexed
Strap (See Table
3-6 on page 58.)
I/O
(PU100)
E31
GPIO14
AMD Geode™ SC3200 Processor Data Book
PMR[24] = 1
VIO
Strap (See Table
3-6 on page 58.)
Cycle Multiplexed
---
PMR[24] = 0
---
VIO
VIO
PMR[24] = 1
VIO
D26
--Strap (See Table
3-6 on page 58.)
Power
Rail Configuration
D14
D24
VIO
PCICLK0
PWR
VSS
PMR[29] = 0
C29
D3
VCORE
D12
PMR[24] = 1
IDE_ADDR1
DID1
D11
PMR[24] = 1
TFTD0
C26
Buffer1
Type
PMR[24] = 0
PMR[24] = 1
VIO
Signal Name
I/O
(PU/
PD)
Ball
No.
VSS
PMR[21] = 0 and
PMR[2] = 1
INTS, O3/
I/O
(PU22.5)
5
GND
---
PMR[21] = 1 and
PMR[2] = 1
---
---
31
Revision 5.1
Table 3-2.
Ball
No.
F3
Signal Name
RD#
I/O
(PU/
PD)
Signal Definitions
432-EBGA Ball Assignment - Sorted by Ball Number (Continued)
Buffer1
Type
Power
Rail Configuration
O
O3/5
I
(PD100)
INSTRP
AD23
I/O
INPCI,
OPCI
A23
O
OPCI
F28
THRM#
I
INTS
VSB
---
F29
VSB
PWR
---
---
F30
VSS
GND
---
---
CLKSEL0
F4
VIO
---
-----
---
J3
IRTX
O
O8/8
VIO
PMR[6] = 0
SOUT3
O
O8/8
---
G3
IOW#
O
O3/5
VIO
DOCW#
O
O3/5
I/O
INTS, O3/
(PU22.5)
5
PMR[21] = 0 and
PMR[2] = 0
I/O
INTS, O3/
(PU22.5)
5
IOCS0#
O
(PU22.5)
O3/5
PMR[21] = 0 and
PMR[2] = 1
PMR[23]2 = 0 and
PMR[5] = 1
TFTDCK
O
(PU22.5)
O1/4
PMR[23]2 = 1
PMR[21] = 1 and
PMR[2] = 1
O
O3/5
VIO
---
BOOT16
I
(PD100)
INSTRP
VIO
Strap (See Table
3-6 on page 58.)
VSB
---
VSB
---
VIO
PWR
---
---
---
O
OD14
VSB
---
H1
O
O3/5
VIO
PMR[12] = 0
VIO
PMR[12] = 1
H3
PMR[6] =1
POR#
I
INTS
VIO
---
MD0
I/O
INT, TS2/5
VIO
---
J313
MD1
I/O
INT, TS2/5
VIO
---
K1
NC
---
---
---
---
K2
VSS
GND
---
---
---
J29
3
---
---
---
---
---
K28
VSS
GND
---
---
---
K29
3
MD2
I/O
INT, TS2/5
VIO
---
PMR[23]2 = 0 and
PMR[13] = 0
K30
3
MD3
I/O
INT, TS2/5
VIO
---
K31
3
MD4
I/O
INT, TS2/5
VIO
---
L1
VSS
GND
---
---
---
L2
VSS
GND
---
---
---
O1/4
VIO
PMR[23]2 = 1
GPIO20
INT, O3/5
I/O
(PU22.5)
2
PMR[23] = 0 and
PMR[7] = 0
PMR[23]2 = 0 and
PMR[7] = 1
PMR[23]2 = 1
L3
VIO
PWR
---
---
---
L4
VCORE
PWR
---
---
---
L28
VCORE
PWR
---
---
---
L293
MD5
I/O
INT, TS2/5
VIO
---
L30
VSS
GND
---
---
---
L313
MD6
I/O
INT, TS2/5
VIO
---
M1
VIO
PWR
---
---
---
M2
VIO
PWR
---
---
---
GPIO19
INTS, O3/
I/O
(PU22.5)
5
INTC#
I
(PU22.5)
INTS
PMR[9] = 0 and
PMR[4] = 1
M3
NC
---
---
---
---
IOCHRDY
I
(PU22.5)
INTS1
PMR[9] = 1 and
PMR[4] = 1
M4
VSS
GND
---
---
---
M28
VSS
GND
---
---
---
PWR
---
---
---
M293
MD7
I/O
INT, TS2/5
VIO
---
O
O2/5
VSB
---
M30
VIO
---
M31
DQM0
N1
N2
H28
VSBL
H29
CLK32
32
PMR[6] = 0
VIO
---
O
(PU22.5)
O1/4
VSB
GND
TFTD12
O
(PU22.5)
INTS
INTS
PWR
PMR[23]2 = 0 and
PMR[13] = 1
TFTD0
I
I
VCORE
VIO
O3/5
IRRX1
SIN3
VSS
O3/5
O
(PU22.5)
PMR[23]2 = 0 and
PMR[5] = 0
K3
O
(PU22.5)
VIO
VIO
K4
IOCS1#
DOCCS#
H4
VIO
J28
J30
G313, 4 PWRCNT2
INT, O3/5
I/O
(PU22.5)
PMR[6] = 1
GPIO17
J4
ROMCS#
GPIO1
F3BAR0+Memory
Offset 08h[21] = 1
VIO
---
H2
VSB
VIO
---
INTS, O3/
I/O
(PU22.5)
5
INTS
O1/4
PWR
GPIO0
I
O1/4
VIO
TRDE#
PMR[18] = 0 and
PMR[8] = 1
O
G2
G30
INTS1
O
VIO
INTS,
TS2/14
I
(PU22.5)
VSYNC
VSB
I/O
(PU100)
IRQ15
HSYNC
O3/5
GPWIO2
PMR[18] = 1 and
PMR[8] = 0
J2
OD14
G29
INTS
J1
O
INTs, TS2/
I/O
(PU100)
14
I
(PU22.5)
PMR[18] = 0 and
PMR[8] = 0
---
O
GPWIO1
RI2#
VIO
---
PWRCNT1
G28
INTS, O8/
I/O
(PU22.5)
8
SDATA_IN2
WR#
G4
GPIO11
H31
F31
GPIO15
Power
Rail Configuration
H30
Cycle Multiplexed
G1
3, 4
Buffer1
Type
Signal Name
Strap (See Table
3-6 on page 58.)
VIO
I/O
(PU/
PD)
Ball
No.
VIO
PMR[9] = 0 and
PMR[4] = 0
PWR
---
---
O
O2/5
VIO
---
VIO
PWR
---
---
---
NC
---
---
---
---
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
Table 3-2.
I/O
(PU/
PD)
432-EBGA Ball Assignment - Sorted by Ball Number (Continued)
Buffer1
Type
Ball
No.
Signal Name
N3
VSS
GND
---
---
N4
VCORE
PWR
---
---
N28
VCORE
PWR
---
---
N29
WEA#
O
O2/5
VIO
N30
CASA#
O
O2/5
VIO
---
Ball
No.
Signal Name
---
T29
MA2
---
T30
VCORE
---
T31
MA1
---
U13, 4
PD7
Power
Rail Configuration
N31
RASA#
O
O2/5
VIO
---
P1
NC
---
---
---
---
P2
NC
---
---
---
---
P3
VSS
GND
---
---
---
P4
VSS
GND
---
---
---
P28
VSS
GND
---
---
---
P29
CS0#
O
O2/5
VIO
---
P30
BA0
O
O2/5
VIO
---
P31
BA1
O
O2/5
VIO
---
R1
VPLL2
PWR
---
---
---
R2
VSS
GND
---
---
---
R3
AVSSPLL2
GND
---
---
---
R4
VCORE
PWR
---
---
---
R28
VCORE
PWR
---
---
---
R29
MA10
R30
VSS
R31
T1
3, 4
T3
GND
---
---
---
O2/5
VIO
---
I
INT
VIO
PMR[23]2 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
O
O
O1/4
O1/4
F_C/BE3#
DQM4
O
O
O
O2/5
U2
U3
AMD Geode™ SC3200 Processor Data Book
O
O1/4
PMR[23]2 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
F_AD7
O
O14/14
PMR[23]2 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
GND
---
---
---
ACK#
I
INT
VIO
PMR[23]2 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
TFTDE
O
O1/4
PMR[23]2 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
FPCICLK
O
O1/4
PMR[23]2 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
VSS
3, 4
U4
VCORE
PWR
---
---
---
U28
VCORE
PWR
---
---
---
U293
MD33
U30
VSS
I/O
INT, TS2/5
VIO
---
GND
---
---
---
U313
V13, 4
MD32
I/O
INT, TS2/5
VIO
---
PD4
I/O
INT, O14/
VIO
PMR[23]2 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
14
I/O
INT, O14/
V23, 4
VIO
14
V33, 4
PMR[23]2 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
TFTD11
O
O1/4
PMR[23]2 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
F_AD5
O
O14/14
PMR[23]2 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
PD6
I/O
INT, O14/
VIO
14
PMR[23]2 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
PMR[23]2 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
TFTD1
O
O1/4
PMR[23]2 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
PMR[23]2 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0
F_AD6
O
O14/14
PMR[23]2 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
VSS
GND
---
V28
VSS
GND
V293
MD36
I/O
PMR[23]2 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
VIO
TFTD13
PD5
PMR[23]2 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
O1/4
PMR[23]2 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
14
PMR[23]2 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
O1/4
---
VIO
PMR[23]2 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
PMR[23]2 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
(PU/PD under software control.)
TFTD15
VIO
O14/14
---
VIO
O2/5
INT, O14/
O
---
INT
O
I/O
F_AD4
VIO
I
---
PMR[23]2 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
---
SLCT
---
---
PMR[23]2 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
INT
O1/4
VIO
---
O1/4
I
(PU22.5
PD22.5)
O
O2/5
O
PWR
O1/4
O
PWR
Power
Rail Configuration
TFTD10
VIO
O
Buffer1
Type
PMR[23]2 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
PE
F_C/BE2#
T28
---
O
TFTD14
T43, 4
VIO
MA0
F_C/BE1#
3, 4
O2/5
BUSY/WAIT#
TFTD3
T2
O
I/O
(PU/
PD)
---
V4
---
---
---
---
---
INT, TS2/5
VIO
---
33
Revision 5.1
Table 3-2.
Buffer1
Type
MD35
I/O
INT, TS2/5
VIO
---
MD34
I/O
INT, TS2/5
VIO
---
SLIN#/ASTRB#
O
O14/14
VIO
PMR[23]2 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
TFTD6
O
O1/4
PMR[23]2 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
TFTD16
O
O1/4
PMR[23]2 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
F_AD0
O
O14/14
PMR[23]2 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
F_IRDY#
O
O14/14
PMR[23]2 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
GND
---
---
---
I
INT, O1/4
VIO
PD3
I/O
INT, O14/
PMR[23]2 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
Signal Name
V303
V313
W13, 4
W2
432-EBGA Ball Assignment - Sorted by Ball Number (Continued)
I/O
(PU/
PD)
Ball
No.
3, 4
Signal Definitions
Power
Rail Configuration
VIO
14
TFTD9
F_AD3
W33, 4
PD2
O
O
I/O
O1/4
O14/14
INT, O14/
VIO
TFTD8
O
O1/4
F_C/BE0#
O
O1/4
PMR[23]2 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
PMR[23]2 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
---
---
W28
VCORE
PWR
---
---
---
W293
MD39
I/O
INT, TS2/5
VIO
---
W303
MD38
I/O
INT, TS2/5
VIO
---
W313
MD37
I/O
INT, TS2/5
VIO
---
Y13, 4
PD1
I/O
INT, O14/
VIO
PMR[23]2 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
VIO
INIT#
TFTD5
SMI_O
PMR[23]2 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
PWR
---
---
---
VCORE
PWR
---
---
---
AA293
MD44
AA30
VSS
I/O
INT, TS2/5
VIO
---
GND
---
---
---
AA313
MD45
I/O
INT, TS2/5
VIO
---
STB#/WRITE#
O
O14/14
VIO
PMR[23]2 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
TFTD17
O
O1/4
PMR[23]2 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
F_FRAME#
O
O14/14
PMR[23]2 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
AB23, 4 AFD#/DSTRB#
O
O14/14
TFTD2
O
O1/4
PMR[23]2 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
INTR_O
O
O14/14
PMR[23]2 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
AB1
3, 4
VIO
PMR[23]2
= 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
O14/14
PMR[23]2 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
PMR[23]2 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
AB3
NC
---
---
---
---
VSS
GND
---
---
---
---
---
---
O
O14/14
VIO
PMR[23]2 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
AB28
VSS
GND
---
---
---
AB293
MD41
I/O
INT, TS2/5
VIO
---
AB303
MD42
I/O
INT, TS2/5
VIO
---
3
MD43
I/O
INT, TS2/5
VIO
---
AC1
NC
---
---
---
---
AC2
NC
---
---
---
---
AC3
VIO
PWR
---
---
---
AC4
VSS
GND
---
---
---
O
O
GND
Y28
VSS
GND
Y293
MD46
I/O
Y30
VIO
34
VCORE
AA28
PWR
VSS
MD47
AA4
AB4
Y4
Y313
AA33, 4 ERR#
PMR[23]2 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
---
Y2
VSS
PMR[23]2 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
PWR
Y33, 4
AA2
PMR[23]2 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
O1/4
VCORE
O
VIO
O
W4
F_AD1
INT, O14/
TFTD4
O14/14
O1/4
I/O
Power
Rail Configuration
PMR[23] = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
O
O
Buffer1
Type
2
F_AD2
TFTD7
I/O
(PU/
PD)
14
PMR[23]2 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
14
Signal Name
AA13, 4 PD0
PMR[23]2 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
14
Ball
No.
O1/4
O14/14
---
PMR[23]2 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
AB31
---
---
---
---
---
AC28
CKEA
O
O2/5
VIO
---
INT, TS2/5
VIO
---
AC29
SDCLK0
O
O2/5
VIO
---
---
---
AC30
DQM5
O
O2/5
VIO
---
MD40
I/O
INT, TS2/5
VIO
---
PWR
I/O
PMR[23]2 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
INT, TS2/5
VIO
---
AC31
3
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
Table 3-2.
Ball
No.
Signal Name
I/O
(PU/
PD)
432-EBGA Ball Assignment - Sorted by Ball Number (Continued)
Buffer1
Type
Power
Rail Configuration
I/O
(PU/
PD)
Buffer1
Type
Power
Rail Configuration
Ball
No.
Signal Name
AH3
GPIO6
INTS, O1/
I/O
(PU22.5)
4
DTR2#/BOUT2
O
(PU22.5)
O1/4
PMR[18] = 1 and
PMR[8] = 0
IDE_IOR1#
O
(PU22.5)
O1/4
PMR[18] = 0 and
PMR[8] = 1
SDTEST5
O
(PU22.5)
O2/5
PMR[18] = 1 and
PMR[8] = 1
GPIO7
INTS, O1/
I/O
(PU22.5)
4
RTS2#
O
(PU22.5)
O1/4
PMR[17] = 1 and
PMR[8] = 0
AD1
NC
---
---
---
---
AD2
NC
---
---
---
---
AD3
NC
---
---
---
---
AD4
NC
---
---
---
---
AD28
MA6
O
O2/5
VIO
---
AD29
MA7
O
O2/5
VIO
---
AD30
MA8
O
O2/5
VIO
---
AD31
MA9
O
O2/5
VIO
---
AE1
NC
---
---
---
---
AE2
VIO
PWR
---
---
---
AE3
INTA#
I
(PU22.5)
INPCI
VIO
---
IDE_DACK1#
O
(PU22.5)
O1/4
PMR[17] = 0 and
PMR[8] = 1
AE43
DPOS_PORT3
I/O
INUSB,
OUSB
AVCCUSB
---
SDTEST0
O
(PU22.5)
O2/5
PMR[17] = 1 and
PMR[8] = 1
AE28
MA3
O
O2/5
VIO
---
AH5
TDP
I/O
Diode
---
---
AE29
MA4
O
O2/5
VIO
---
AH6
TDO
O
OPCI
VIO
---
AE30
VIO
PWR
---
---
---
AH7
VPCKIN
I
INT
VIO
---
VPD4
I
INT
VIO
---
AE31
MA5
AF1
INTB#
AF2
AF3
VSS
3
DNEG_PORT3
AF4
AVCCUSB
AF283
MD14
AF293
MD15
AF30
VSS
AF31
DQM1
AG1
AVSSUSB
AG23
DNEG_PORT2
AG33
DNEG_PORT1
AG4
GPIO9
VIO
PMR[18] = 0 and
PMR[8] = 0
PMR[17] = 0 and
PMR[8] = 0
O
O2/5
VIO
---
AH8
I
(PU22.5)
INPCI
VIO
---
AH9
VPD0
I
INT
VIO
---
AH10
VSS
GND
---
---
---
GND
---
---
---
AH11
VCORE
PWR
---
---
---
I/O
INUSB,
OUSB
AVC-
---
AH12
VSS
GND
---
---
---
AH13
VCORE
PWR
---
---
---
AH14
VSS
GND
---
---
---
AH15
VCORE
PWR
---
---
---
CUSB
PWR
---
---
---
I/O
INT, TS2/5
VIO
---
I/O
INT, TS2/5
VIO
---
GND
---
---
---
O
O2/5
VIO
---
GND
---
---
---
I/O
INUSB,
OUSB
AVCCUSB
---
I/O
INUSB,
OUSB
INTS, O1/
I/O
(PU22.5)
4
AVCCUSB
VIO
---
AH16
SDCLK1
O
O2/5
VIO
---
AH17
VCORE
PWR
---
---
---
AH18
VSS
GND
---
---
-----
AH19
VCORE
PWR
---
---
AH20
VSS
GND
---
---
---
AH21
VCORE
PWR
---
---
---
VSS
GND
---
---
---
AH23
3
MD28
I/O
INT, TS2/5
VIO
---
AH24
3
MD55
I/O
INT, TS2/5
VIO
---
AH253
MD51
I/O
INT, TS2/5
VIO
---
3
MD48
I/O
INT, TS2/5
VIO
---
AH273
MD23
I/O
INT, TS2/5
VIO
---
AH28
SDCLK_OUT
O
O2/5
VIO
---
AH22
PMR[18] = 0 and
PMR[8] = 0
PMR[18] = 1 and
PMR[8] = 0
I
(PU22.5)
INTS
IDE_IOW1#
O
(PU22.5)
O1/4
PMR[18] = 0 and
PMR[8] = 1
SDTEST2
O
(PU22.5)
O2/5
PMR[18] = 1 and
PMR[8] = 1
DCD2#
AH4
VIO
AH26
AG28
MA11
O
O2/5
VIO
---
AH29
MA12
O
O2/5
VIO
---
AG293
MD9
I/O
INT, TS2/5
VIO
---
AH303
MD11
I/O
INT, TS2/5
VIO
---
MD10
I/O
INT, TS2/5
VIO
---
GPIO10
INTS, O8/
I/O
(PU22.5)
8
VIO
PMR[18] = 0 and
PMR[8] = 0
DSR2#
I
(PU22.5)
INTS
PMR[18] = 1 and
PMR[8] = 0
IDE_IORDY1
I
(PU22.5)
INTS1
PMR[18] = 0 and
PMR[8] = 1
SDTEST1
O
(PU22.5)
O2/5
PMR[18] = 1 and
PMR[8] = 1
AG303
MD8
I/O
INT, TS2/5
VIO
---
AH313
AG313
MD13
I/O
INT, TS2/5
VIO
---
AJ1
DPOS_PORT2
I/O
INUSB,
OUSB
AVCCUSB
---
INUSB,
OUSB
AVCCUSB
---
AH1
3
AH23
DPOS_PORT1
I/O
AMD Geode™ SC3200 Processor Data Book
35
Revision 5.1
Table 3-2.
Ball
No.
Signal Name
AJ2
GPIO8
CTS2#
IDE_DREQ1
SDTEST4
AJ3
AJ4
VIO
SIN2
SDTEST3
AJ5
TMS
I/O
(PU/
PD)
432-EBGA Ball Assignment - Sorted by Ball Number (Continued)
Buffer1
Type
INTS, O8/
I/O
(PU22.5)
8
I
(PU22.5)
INTS1
O
(PU22.5)
O2/5
I
Power
Rail Configuration
VIO
--INTS
O
O2/5
I
(PU22.5)
INPCI
PMR[17] = 0 and
PMR[8] = 0
PMR[17] = 1 and
PMR[8] = 0
INTS
I
(PU22.5)
PWR
Signal Definitions
VIO
VIO
AJ22
---
AJ23
3
MD29
I/O
INT, TS2/5
VIO
---
PMR[17] = 1 and
PMR[8] = 1
AJ243
MD54
I/O
INT, TS2/5
VIO
---
---
AJ253
MD50
I/O
INT, TS2/5
VIO
---
PMR[28] = 0
AJ26
DQM6
O
O2/5
VIO
---
MD22
I/O
INT, TS2/5
VIO
---
I/O
INT, TS2/5
VIO
---
PWR
---
---
-----
---
AJ283
MD19
AJ29
VIO
---
AJ8
VPD2
I
INT
VIO
---
AJ9
GPIO38/IRRX2
I/O
(PU22.5)
INPCI,
OPCI
VIO
PMR[14]5 = 0 and
PMR[22]5 = 0. The
IRRX2 input is
connected to the
input path of
GPIO38. There is
no logic required to
enable IRRX2, just
a simple connection. Hence, when
GPIO38 is the
selected function,
IRRX2 is also
selected.
AJ11
AJ12
AJ13
GPIO32
I/O
(PU22.5)
INPCI,
OPCI
LAD0
I/O
(PU22.5)
INPCI,
OPCI
GPIO12
I/O
INAB, O8/
(PU22.5)
8
AB2C
I/O
(PU22.5)
INAB,
OD8
I/O
(PU22.5)
INAB,
OD8
AB1C
GPIO20
AJ14
AJ15
AJ16
AJ173
AJ183
36
O
O3/5
AC97_CLK
O
O2/5
O
O2/5
F_STOP#
O
O2/5
SDCLK3
O
O2/5
MD56
MD58
I/O
I/O
INT, TS2/5
INT, TS2/5
PMR[19] = 0
PMR[19] = 1
VIO
INT
VIO
INT, TS2/5
VIO
---
VIO
PWR
---
---
---
AK2
VSS
GND
---
---
---
AK3
SOUT2
O
O8/8
VIO
---
CLKSEL2
I
(PD100)
INSTRP
AK4
TRST#
I
(PU22.5)
INPCI
VIO
---
AK5
TDI
I
(PU22.5)
INPCI
VIO
---
AK6
VIO
PWR
---
---
---
AK7
VSS
GND
---
---
---
AK8
VPD1
I
INT
VIO
---
AK9
GPIO37
I/O
(PU22.5)
INPCI,
OPCI
VIO
PMR[14]5 = 0 and
PMR[22]5 = 0
O
OPCI
GPIO34
I/O
(PU22.5)
INPCI,
OPCI
LAD2
I/O
(PU22.5)
INPCI,
OPCI
SDCLK_IN
MD12
AK1
LFRAME#
AK10
PMR[14]5 = 0 and
PMR[22]5 = 0
PMR[14]5 = 1 and
PMR[22]5 = 1
VIO
I
I/O
AJ30
AJ313
PMR[14]5 = 0 and
PMR[22]5 = 0
PMR[14]5 = 1 and
PMR[22]5 = 1
PMR[23]2
PMR[23]2 = 1 and
PMR[7] = 1
VIO
VIO
VIO
VIO
VIO
PMR[25] = 1
FPCI_MON = 0
PMR[14]5 = 1 and
PMR[22]5 = 1
VIO
PMR[14]5 = 0 and
PMR[22]5 = 0
PMR[14]5 = 1 and
PMR[22]5 = 1
VIO
PWR
---
---
---
AK12
VSS
GND
---
---
---
AK13
SDATA_OUT
O
OAC97
VIO
---
TFT_PRSNT
I
(PD100)
INSTRP
VIO
Strap (See Table
3-6 on page 58.)
I
INT
VIO
FPCI_MON = 0
=0
PMR[23]2 = 1 and
PMR[7] = 0
Strap (See Table
3-6 on page 58.)
AK11
AK14
INT, O3/5
I/O
(PU22.5)
DOCCS#
AC97_RST#
PMR[14]5 = 1 and
PMR[22]5 = 1
VIO
3
AJ27
---
INPCI,
OPCI
AJ21
PMR[28] = 1
VIO
I/O
(PU22.5)
-----
VIO
LAD3
---
VIO
VIO
INT
VIO
VIO
O2/5
VIO
INT
INPCI,
OPCI
INT, TS2/5
O
O2/5
I
I/O
(PU22.5)
I/O
INT, TS2/5
I
GPIO35
MD61
DQM7
O
VPD6
AJ10
AJ193
AJ20
I/O
VPD7
OPCI
Power
Rail Configuration
MD25
AJ7
O
Buffer1
Type
DQM3
AJ6
LPCPD#
Signal Name
I/O
(PU/
PD)
3
PMR[17] = 0 and
PMR[8] = 1
---
Ball
No.
SDATA_IN
F_GNT0#
FPCI_MON = 1
O
O2/5
AK15
VSS
GND
---
---
---
AK16
VIO
PWR
---
---
---
AK17
VSS
GND
---
---
---
AK183
MD59
I/O
INT, TS2/5
VIO
---
3
MD62
I/O
INT, TS2/5
VIO
---
FPCI_MON = 1
AK19
---
AK20
VIO
PWR
---
---
---
---
AK21
VSS
GND
---
---
---
I/O
INT, TS2/5
VIO
---
---
AK22
3
MD26
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
Table 3-2.
432-EBGA Ball Assignment - Sorted by Ball Number (Continued)
I/O
(PU/
PD)
Buffer1
Type
MD30
I/O
INT, TS2/5
VIO
---
MD53
I/O
INT, TS2/5
VIO
---
VIO
PWR
---
---
---
AK26
VSS
GND
---
---
---
AK273
MD21
I/O
INT, TS2/5
VIO
---
AK283
MD18
I/O
INT, TS2/5
VIO
---
AK29
CS1#
O
O2/5
VIO
---
AK30
VSS
GND
---
---
---
AK31
VIO
PWR
---
---
---
AL1
VSS
GND
---
---
---
AL2
VIO
PWR
---
---
---
AL3
TDN
I/O
WIRE
VIO
---
AL4
TCK
I
(PU22.5)
INPCI
VIO
---
Ball
No.
Signal Name
AK233
AK243
AK25
Power
Rail Configuration
I
(PD22.5)
INT
VIO
---
VPD5
I
INT
VIO
---
AL7
VPD3
I
INT
VIO
---
AL8
GPIO39
I/O
(PU22.5)
INPCI,
OPCI
VIO
PMR[14]5 = 0 and
PMR[22]5 = 0
SERIRQ
I/O
INPCI,
OPCI
AL5
GTEST
AL6
AL9
AL10
AL11
AL12
AL13
GPIO36
I/O
(PU22.5)
INPCI,
OPCI
LDRQ#
I
INPCI
GPIO33
I/O
(PU22.5)
INPCI,
OPCI
LAD1
I/O
(PU22.5)
INPCI,
OPCI
GPIO13
I/O
INAB, O8/
(PU22.5)
8
AB2D
I/O
(PU22.5)
AB1D
I/O
(PU22.5)
GPIO1
I/O
INT, O3/5
(PU22.5)
AL14
AL15
PMR[19] = 1
INAB,
OD8
VIO
PMR[23]2 = 0
OAC97
I
(PD100)
INSTRP
BIT_CLK
I
INT
O
O1/4
GPIO16
I/O
INT, O2/5
(PU22.5)
O
O1/4
PMR[23]2 = 1
TEST3
O
O2/5
PMR[23]2 = 0 and
PMR[29] = 1 and
AL173
MD57
I/O
INT, TS2/5
VIO
---
AL183
MD60
I/O
INT, TS2/5
VIO
---
AL193
MD63
I/O
INT, TS2/5
VIO
---
AL20
Power
Rail Configuration
VIO
PMR[23]2 = 0 and
PMR[29] = 0
SDCLK2
O
O2/5
VIO
---
AL21
3
MD24
I/O
INT, TS2/5
VIO
---
AL22
3
MD27
I/O
INT, TS2/5
VIO
---
AL23
3
MD31
I/O
INT, TS2/5
VIO
---
AL243
MD52
I/O
INT, TS2/5
VIO
---
AL253
MD49
I/O
INT, TS2/5
VIO
---
AL26
DQM2
O
O2/5
VIO
---
AL273
MD20
I/O
INT, TS2/5
VIO
---
3
MD17
I/O
INT, TS2/5
VIO
---
AL293
MD16
I/O
INT, TS2/5
VIO
---
AL30
VIO
PWR
---
---
---
VSS
GND
---
---
---
AL31
1.
2.
3.
For Buffer Type definitions, refer to Table 9-10 "Buffer Types" on page
375.
The TFT_PRSNT strap determines the power-on reset (POR) state of
PMR[23].
Is back-drive protected (MD[63:0], DPOS_PORT1, DNEG_PORT1,
DPOS_PORT2, DNEG_PORT2, DPOS_PORT3, DNEG_PORT3,
ACK#, AFD#/DSTRB#, BUSY/WAIT#, ERR#, INIT#, PD[7:0], PE,
SLCT, SLIN#/ASTRB#, STB#/WRITE#, ONCTL#, PWRCNT[2:1]).
Is 5V tolerant (ACK#, AFD#/DSTRB#, BUSY/WAIT#, ERR#, INIT#,
PD[7:0], PE, SLCT, SLIN#/ASTRB#, STB#/WRITE#, ONCTL#,
PWRCNT[2:1]).
The LPC_ROM strap determines the power-on reset (POR) state of
PMR[14] and PMR[22].
PMR[23]2 = 1and
PMR[13] = 0
O3/5
F_TRDY#
FP_VDD_ON
5.
VIO
O
O2/5
PMR[14]5 = 1 and
PMR[22]5 = 1
INAB,
OD8
SYNC
O
4.
PMR[19] = 0
O
GXCLK
AL16
PMR[14]5 = 0 and
PMR[22]5 = 0
VIO
IOCS1#
CLKSEL3
PMR[14]5 = 0 and
PMR[22]5 = 0
PMR[14]5 = 1 and
PMR[22]5 = 1
VIO
Buffer1
Type
Signal Name
AL28
PMR[14]5 = 1 and
PMR[22]5 = 1
VIO
I/O
(PU/
PD)
Ball
No.
PMR[23]2 = 1 and
PMR[13] = 1
VIO
--Strap (See Table
3-6 on page 58.)
VIO
FPCI_MON = 0
FPCI_MON = 1
VIO
PMR[0] = 0 and
FPCI_MON = 0
PC_BEEP
O
O2/5
PMR[0] = 1 = 0
and FPCI_MON =
0
F_DEVSEL#
O
O2/5
FPCI_MON = 1
AMD Geode™ SC3200 Processor Data Book
37
Revision 5.1
Signal Definitions
Table 3-3. 432-EBGA Ball Assignment - Sorted Alphabetically by Signal Name
Signal Name
Ball No.
Signal Name
A0
A17
AD18
A1
D16
A2
A18
A3
A4
Ball No.
Signal Name
Ball No.
D7
D9
A10
AD19
A6
D10
D8
AD20
D6
D11
A8
A15
AD21
C6
D12
C10
A16
AD22
A5
D13
B8
A5
A14
AD23
F4
D14
C8
A6
C15
AD24
C5
D15
A7
B14
AD25
D5
DCD2#
A8
C14
AD26
A4
DEVSEL#
B5
A9
B13
AD27
B4
DID0
D4
A10
C13
AD28
C4
DID1
A11
C12
AD29
A3
DNEG_PORT1
AG3
A12
A12
AD30
C2
DNEG_PORT2
AG2
A13
C11
AD31
B3
DNEG_PORT3
A14
A11
AFD#/DSTRB#
AB2
DOCCS#
A15
B10
AVCCUSB
AF4
DOCR#
F1
A16
A7
AVSSPLL2
R3
DOCW#
G3
A17
C7
AVSSPLL3
E28
DPOS_PORT1
AH2
A18
D7
DPOS_PORT2
AH1
A19
A6
A20
D6
A21
C6
A22
A5
A23
F4
AB1C
AJ13
AB1D
AL12
AB2C
AJ12
AB2D
AL11
AC97_CLK
AJ14
AC97_RST#
AJ15
ACK#
U3
AD0
A17
AD1
D16
AD2
A18
AD3
A15
AD4
A16
AD5
A14
AD6
C15
AD7
B14
AD8
C14
AD9
B13
AD10
C13
AD11
C12
AD12
A12
AD13
C11
AD14
A11
AD15
B10
AD16
A7
AD17
C7
38
AVSSUSB
AG1
BA0
P30
BA1
P31
BHE#
B5
BIT_CLK
AL14
BOOT16
G4
BUSY/WAIT#
T1
C/BE0#
A13
C/BE1#
A10
C/BE2#
D8
C/BE3#
A8
CASA#
N30
CKEA
AC28
CLK27M
A23
CLK32
H29
CLKSEL0
F3
CLKSEL1
B27
CLKSEL2
AK3
CLKSEL3
AL13
CS0#
P29
CS1#
AK29
CTS2#
AJ2
D0
C5
D1
D5
D2
A4
D3
B4
D4
C4
D5
A3
D6
C2
D7
B3
D8
A13
D9
AG4
D2
AF3
H3, AJ13
DPOS_PORT3
AE4
DQM0
M31
DQM1
AF31
DQM2
AL26
DQM3
AJ21
DQM4
T28
DQM5
AC30
DQM6
AJ26
DQM7
AJ20
DSR2#
AJ1
DTR1#/BOUT1
A28
DTR2#/BOUT2
AH3
ERR#
AA3
F_AD0
AA1
F_AD1
Y1
F_AD2
W3
F_AD3
W2
F_AD4
V1
F_AD5
V2
F_AD6
V3
F_AD7
U1
F_C/BE0#
AA3
F_C/BE1#
T1
F_C/BE2#
T3
F_C/BE3#
F_DEVSEL#
T4
AL15
F_FRAME#
AB1
F_GNT0#
AK14
F_IRDY#
W1
F_STOP#
AJ15
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
Table 3-3.
Signal Name
F_TRDY#
FP_VDD_ON
432-EBGA Ball Assignment - Sorted Alphabetically by Signal Name (Continued)
Ball No.
Signal Name
Ball No.
Signal Name
Ball No.
AL14
IDE_DATA2
D23
LPCPD#
AJ9
B23, AL16
IDE_DATA3
C23
MA0
R31
FPCI_MON
D3
IDE_DATA4
B23
MA1
T31
FPCICLK
U3
IDE_DATA5
A23
MA2
T29
FRAME#
E1
IDE_DATA6
C22
MA3
AE28
GNT0#
D4
IDE_DATA7
B22
MA4
AE29
GNT1#
D2
IDE_DATA8
A21
MA5
AE31
GPIO0
H1
IDE_DATA9
C20
MA6
AD28
GPIO1
H2, AL12
IDE_DATA10
A20
MA7
AD29
GPIO6
AH3
IDE_DATA11
C19
MA8
AD30
GPIO7
AH4
IDE_DATA12
B19
MA9
AD31
GPIO8
AJ2
IDE_DATA13
A19
MA10
R29
GPIO9
AG4
IDE_DATA14
C18
MA11
AG28
GPIO10
AJ1
IDE_DATA15
B18
MA12
AH29
GPIO11
H30
IDE_DREQ0
C24
MD0
J30
GPIO12
AJ12
IDE_DREQ1
AJ2
MD1
J31
GPIO13
AL11
IDE_IOR0#
C21
MD2
K29
GPIO14
F1
IDE_IOR1#
AH3
MD3
K30
GPIO15
G3
IDE_IORDY0
A25
MD4
K31
GPIO16
AL15
IDE_IORDY1
AJ1
MD5
L29
GPIO17
J4
IDE_IOW0#
D24
MD6
L31
GPIO18
A28
IDE_IOW1#
AG4
MD7
M29
GPIO19
H4
IDE_RST#
A22
MD8
AG30
GPIO20
H3, AJ13
INIT#
Y3
MD9
AG29
GPIO32
AJ11
INTA#
AE3
MD10
AH31
GPIO33
AL10
INTB#
AF1
MD11
AH30
GPIO34
AK10
INTC#
H4
MD12
AJ31
GPIO35
AJ10
INTD#
B22
MD13
AG31
GPIO36
AL9
INTR_O
AB2
MD14
AF28
GPIO37
AK9
IOCHRDY
H4
MD15
AF29
GPIO38/IRRX2
AJ9
IOCS0#
J4
MD16
AL29
GPIO39
AL8
IOCS1#
H2, AL12
MD17
AL28
GPIO40
A21
IOR#
F1
MD18
AK28
GPIO41
C19
IOW#
G3
MD19
AJ28
GPWIO0
E31
IRDY#
C8
MD20
AL27
GPWIO1
G28
IRQ14
D25
MD21
AK27
GPWIO2
G29
IRQ15
H30
MD22
AJ27
GTEST
AL5
IRQ9
C22
MD23
AH27
GXCLK
AL16
IRRX1
J28
MD24
AL21
HSYNC
J1
IRTX
J3
MD25
AJ22
IDE_ADDR0
A26
LAD0
AJ11
MD26
AK22
IDE_ADDR1
C26
LAD1
AL10
MD27
AL22
IDE_ADDR2
C17
LAD2
AK10
MD28
AH23
IDE_CS0#
A27
LAD3
AJ10
MD29
AJ23
IDE_CS1#
C16
LDRQ#
AL9
MD30
AK23
IDE_DACK0#
C25
LED#
D31
MD31
AL23
IDE_DACK1#
AH4
LFRAME#
AK9
MD32
U31
IDE_DATA0
B24
LOCK#
C9
MD33
U29
IDE_DATA1
A24
LPC_ROM
E4
MD34
V31
AMD Geode™ SC3200 Processor Data Book
39
Revision 5.1
Table 3-3.
Signal Name
MD35
Signal Definitions
432-EBGA Ball Assignment - Sorted Alphabetically by Signal Name (Continued)
Ball No.
Signal Name
V30
PE
MD36
V29
MD37
W31
MD38
Ball No.
Signal Name
Ball No.
T3
TDN
AL3
PERR#
B9
TDO
AH6
PLL2B
D28
TDP
AH5
W30
PLL5B
B29
TEST0
D28
MD39
W29
PLL6B
C28
TEST1
C28
MD40
AC31
POR#
J29
TEST2
B29
MD41
AB29
POWER_EN
B28
TEST3
AL16
MD42
AB30
PWRBTN#
E29
TFT_PRSNT
MD43
AB31
PWRCNT1
F31
TFTD0
MD44
AA29
PWRCNT2
G31
TFTD1
D25, V3
MD45
AA31
RASA#
N31
TFTD10
C21, V1
MD46
Y29
RD#
F3
TFTD11
A25, V2
MD47
Y31
REQ0#
C1
TFTD12
C23, H2
MD48
AH26
REQ1#
E3
TFTD13
B19, U1
MD49
AL25
RI2#
H30
TFTD14
D23, T3
MD50
AJ25
ROMCS#
G4
TFTD15
A19, T4
MD51
AH25
RTS2#
AH4
TFTD16
A24, W1
MD52
AL24
SDATA_IN
AK14
TFTD17
C18, AB1
MD53
AK24
SDATA_IN2
H31
TFTD2
C26, AB2
MD54
AJ24
SDATA_OUT
AK13
TFTD3
A26, T1
MD55
AH24
SDCLK_IN
AJ30
TFTD4
C17, AA3
MD56
AJ17
SDCLK_OUT
AH28
TFTD5
A27, Y3
MD57
AL17
SDCLK0
AC29
TFTD6
B24, AA1
MD58
AJ18
SDCLK1
AH16
TFTD7
B18, Y1
MD59
AK18
SDCLK2
AL20
TFTD8
C24, W3
MD60
AL18
SDCLK3
AJ16
TFTD9
D24, W2
MD61
AJ19
SDTEST0
AH4
TFTDCK
A22, J4
MD62
AK19
SDTEST1
AJ1
TFTDE
C16, U3
MD63
AL19
SDTEST2
AG4
THRM#
F28
SDTEST3
AJ4
TMS
AJ5
SDTEST4
AJ2
TRDE#
H1
SDTEST5
AH3
TRDY#
B8
SERIRQ
AL8
TRST#
AK4
A9
VBAT
NC (Total of 13)
K1, M3, N2, P1,
P2, AB3, AC1,
AC2, AD1, AD2,
AD3, AD4, AE1
ONCTL#
E30
OVER_CUR#
C27
PAR
C10
PC_BEEP
AL15
PCICLK
E2
PCICLK0
D3
PCICLK1
E4
PCIRST#
D1
PD0
AA1
PD1
Y1
PD2
W3
PD3
W2
PD4
V1
PD5
V2
PD6
PD7
40
V3
U1
SERR#
SIN1
D26
SIN2
AJ4
SIN3
J28
SLCT
T4
SLIN#/ASTRB#
W1
SMI_O
Y3
SOUT1
B27
SOUT2
AK3
SOUT3
STB#/WRITE#
VCORE (Total of 26)
AK13
C25, H3
D30
D11, D13, D15,
D17, D19, D21,
K3, L4, L28, N4,
N28, R4, R28,
T30, U4, U28,
W4, W28, AA4,
AA28, AH11,
AH13, AH15,
AH17, AH19,
AH21
J3
AB1
STOP#
D9
SYNC
AL13
TCK
AL4
TDI
AK5
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
Table 3-3.
Signal Name
VIO (Total of 35)
432-EBGA Ball Assignment - Sorted Alphabetically by Signal Name (Continued)
Ball No.
A2, A30, B1, B6,
B11, B16, B20,
B25, B31, C3,
C29, G2, G30,
L3, M1, M2, M30,
N1, T2, Y2, Y30,
AC3, AE2, AE30,
AJ3, AJ29, AK1,
AK6, AK11,
AK16, AK20,
AK25, AK31,
AL2, AL30
VPCKIN
AH7
VPD0
AH9
VPD1
AK8
VPD2
AJ8
VPD3
AL7
VPD4
AH8
VPD5
AL6
VPD6
AJ7
VPD7
AJ6
VPLL2
R1
AMD Geode™ SC3200 Processor Data Book
Signal Name
Ball No.
Signal Name
Ball No.
VPLL3
C31
VSYNC
VSB
F29
WEA#
H28
WR#
G1
X27I
A29
X27O
D27
X32I
C30
X32O
D29
VSBL
VSS (Total of 61)
A1, A31, B2, B7,
B12, B15, B17,
B21, B26, B30,
D10, D12, D14,
D18, D20, D22,
F2, F30, K2, K4,
K28, L1, L2, L30,
M4, M28, N3, P3,
P4, P28, R2, R30,
U2, U30, V4, V28,
Y4, Y28, AA2,
AA30, AB4,
AB28, AC4, AF2,
AF30, AH10,
AH12, AH14,
AH18, AH20,
AH22, AK2, AK7,
AK12, AK15,
AK17, AK21,
AK26, AK30,
AL1, AL31
J2
N29
41
Revision 5.1
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
W
Y
AA
AB
AC
AD
AE
AF
AG
AH
AJ
AK
AL
1
2
VSS
VIO
3
4
5
6
7
8
Signal Definitions
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
S
AD30 PCK0 REQ1# PRST# PCICK IOW# GP20 GP17 HSNC
VIO
VSS
NC
NC
VSS
VPLL2
PD7
VSS
NC
VIO
BUSY ACK#
VSS
PD6
PD1
STB#
NC
NC
NC
D+P3 D-P3 D+P1 D-P1
VIO
VSS
VIO SLIN# INIT#
VSS
NC
VSS
VSS
VSS
VIO
PD5
VIO
NC
NC
VIO INTB# AVSSUSB GP9
GP7
GP8
VSS INTA# AVCCUSB GP6 SOUT TDP
TDN
SIN2 TRST# TDO
TCK
S
VSS
VIO
AD29 AD28 REQ0# AD23
WR#
VSS
VSNC
NC
VIO
AD25 GNT0# GNT1# VIO RMCS# GP19
VIO
IRTX
VSS
VIO
S
AD26 AD24
VIO
VSS
S
RD#
NC
D+P2 D-P2 GP10
S
VSS
VSS AVSSP2 SLCT
PD4
PD3
PD0
S
AD21 AD22 AD20 AD27 AD31 PCK1
VIO
S
VSS
FRM# IOR#
GP1 TRDE# VCORE VSS
VIO
VIO
NC
PE
VIO
VSS
PD2
ERR# AFD#
VIO
NC
AD16 AD19 AD18 DVSL#
TRDY# IRDY# CBE2# AD17
TMS
TDI
STOP# VSS
VSS
VIO
VIO
VSS
AMD Geode™
SC3200 Processor
SRR# PRR# LOCK# CBE3#
AD13 CBE1# AD15
AD11
VIO
CBE0# AD9
VSS
PAR
AD14
AD10 AD12
VSS
AD7
VIO
AD8
AD3
AD6
AD5
VSS
VSS
AD1 VCORE
VSS
VSS
VSS
VCORE VCORE VSS
GP38
VIO
VSS
VCORE VCORE VCORE VCORE
AD0
IAD2
AD2 VCORE
IDAT15 IDAT14 IDAT13 VSS
VIO
VSS IDAT12 IDAT11
VSS VCORE VCORE
VSS
GP37
GP36 GP35 GP34 GP33
VSS VCORE VCORE
VSS
VPD7
VPD2 VPD1 VPD0 GP39
VSS
VIO
VSS
GP12 AB1D AB1C
S
AD4 ICS1#
VSS
VPD6 VPD5 VPD4 VPD3
GP32 GP13
VCORE VCORE VSS
GTST VPCKI
S
VCORE SDO SYNC ACCK
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VCORE VCORE VCORE VCORE
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VCORE ACRST# BITCK SDI
VCORE VCORE VSS
VSS
VSS VCORE VCORE
VCORE VCORE VSS
VSS
VSS VCORE VCORE
VSS
VSS
VSS
VSS
VSS SDCK3 GXCK GP16
MD57 SDCK1 VSS
VIO
IDAT10 IDAT9 IDAT8 IIOR0#
MD58 MD59 MD60 MD56
IRST# IDAT7 IDAT6 IDAT5
SDCK2 MD61 MD62 MD63
IDAT4
MD24
VSS
VIO
IDAT3
VIO
VSS
DQM7
IDAT1 IDAT2 IDAT0 IDRQ0
MD25 MD26 MD27 DQM3
IIORY0 IIOW0# IAD0 IDACK0#
MD52 MD29 MD30 MD31
IAD1
VSS
VIO
(Top View)
VSS
S
VSS
VIO
VSS
MD28
IRQ14 ICS0# SOUT1 OVRCUR#
MD50 MD49 MD54 MD53
GP18 SIN1
MD21 DQM6 DQM2 MD55
X27I TEST1
CK32 POR# MD3
MD5 WEA#
GP11 MD0
VIO
MD6 CASA# BA0
MA10 MD32 MD33 MD36 MD47 MD45 MD42 SDCK0 VIO
MA6
VIO
VSS AVSSP3 THRM#GPW1 PCNT1 VSS IRRX1 MD1
VSS
MD7 RASA# VIO
BA1
VSS
VIO
MD4 DQM0 CS0#
1
2
PWRE X27O TEST0
TEST2 X32I
Note:
VIO PBTN# GPW0 VSS
X32O VPLL3 ONCT# GPW2
VBAT
LED#
VSB
3
4
5
VIO
VSBL PCNT2 SDATI2 MD2
6
7
8
VSS
VSS
VIO
MA1 MD34 MD37
MA2
MA0 DQM4
VIO
VSS
MD41 MA9
MA8 DQM1 MD13
VSS
MA11 CS1# MD18 MD48 MD20 MD51
MA3
VIO
MD11 SDCKI MD19
MA5 MD15
VSS
MD14 MD12 SDCKO MD16
VSS
VIO
MD8 MD10 MD9 MA12 MD23
VIO
VSS
VIO
MD35 MD46
VIO
MD43 DQM5 VSS
VSS
MD38 MD39
VSS
MD44 MD40 CKEA MA7
MA4
VIO
MD22 MD17
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
W
Y
AA
AB
AC
AD
AE
AF
AG
AH
AJ
AK
AL
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
Signal names have been abbreviated in this figure due to space constraints.
= GND Ball
= PWR Ball
S
= Strap Option Ball
= Multiplexed Ball
Figure 3-3. 481-TEPBGA Ball Assignment Diagram
42
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
Table 3-4. 481-TEPBGA Ball Assignment - Sorted by Ball Number
I/O
Buffer1 Power
Rail Configuration
(PU/PD) Type
Ball
No.
Signal Name
A1
VSS
GND
---
---
---
A2
VIO
PWR
---
---
---
A3
AD30
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
D6
I/O
INPCI,
OPCI
A4
PCICLK0
FPCI_MON
A5
REQ1#
O
OPCI
VIO
INSTRP
I
(PD100)
I
INPCI
Signal Name
A205, 2
PD6
I/O
INT,
O14/14
TFTD1
O
O1/4
PMR[23]3 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0
F_AD6
O
O14/14
PMR[23]3 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
PD1
I/O
INT,
O14/14
TFTD7
O
O1/4
PMR[23]3 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
F_AD1
O
O14/14
PMR[23]3 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
STB#/WRITE#
O
O14/14
TFTD17
O
O1/4
PMR[23]3 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
F_FRAME#
O
O14/14
PMR[23]3 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
A23
NC
---
---
---
---
A24
NC
---
---
---
---
A25
NC
---
---
---
---
A265
DPOS_PORT3
I/O
INUSB,
OUSB
AVC-
---
CUSB
A215, 2
A6
PCIRST#
A7
PCICLK
A8
IOW#
DOCW#
O
O3/5
PMR[21] = 0 and
PMR[2] = 1
GPIO15
I/O
(PU22.5)
INTS,
O3/5
PMR[21] = 1 and
PMR[2] = 1
GPIO20
INT, O3/
I/O
(PU22.5)
5
DOCCS#
O
(PU22.5)
O3/5
PMR[23]3 = 0 and
PMR[7] = 1
TFTD0
O
(PU22.5)
O1/4
PMR[23]3 = 1
I/O
(PU22.5)
INTS,
O3/5
A9
A10
GPIO17
OPCI
VIO
---
I
INT
VIO
---
O
O3/5
VIO
PMR[21] = 0 and
PMR[2] = 0
VIO
VIO
PMR[23] = 0 and
PMR[7] = 0
PMR[23]3 = 0 and
PMR[5] = 0
O
(PU22.5)
O3/5
PMR[23]3 = 0 and
PMR[5] = 1
TFTDCK
O
(PU22.5)
O1/4
PMR[23]3 = 1
A11
HSYNC
O
O1/4
VIO
---
A12
VIO
PWR
---
---
---
A13
VSS
GND
---
---
---
A14
NC
---
---
---
A15
NC
---
---
---
A16
VSS
GND
---
A17
VPLL2
PWR
PD7
A18
A19
A225, 2
VIO
3
IOCS0#
5, 2
VIO
---
(PU22.5)
O
VIO
--Strap (See Table 36 on page 58.)
VIO
I/O
Buffer1 Power
Rail Configuration
(PU/PD) Type
Ball
No.
PMR[23]3 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
PMR[23]3 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
PMR[23]3 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
A275
DNEG_PORT3
I/O
INUSB,
OUSB
AVCCUSB
---
A285
DPOS_PORT1
I/O
INUSB,
OUSB
AVCCUSB
---
A295
DNEG_PORT1
I/O
INUSB,
OUSB
AVCCUSB
---
---
A30
VIO
PWR
---
---
---
---
A31
VSS
GND
---
---
---
---
---
B1
VSS
GND
---
---
---
---
---
---
B2
VIO
PWR
---
---
---
I/O
INT,
O14/14
VIO
B3
AD29
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
TFTD13
O
O1/4
PMR[23]3 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
D5
I/O
INPCI,
OPCI
AD28
I/O
Cycle Multiplexed
O
O14/14
PMR[23]3 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
INPCI,
OPCI
VIO
F_AD7
D4
I/O
INPCI,
OPCI
VIO
---
VSS
GND
---
---
AMD Geode™ SC3200 Processor Data Book
3
PMR[23] = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
---
B4
B5
REQ0#
INPCI
I
(PU22.5)
43
Revision 5.1
Table 3-4.
Ball
No.
Signal Name
B6
AD23
Signal Definitions
481-TEPBGA Ball Assignment - Sorted by Ball Number (Continued)
I/O
Buffer1 Power
Rail Configuration
(PU/PD) Type
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
Ball
No.
Signal Name
I/O
Buffer1 Power
Rail Configuration
(PU/PD) Type
B25
VSS
GND
---
---
---
B26
NC
---
---
---
---
B275
DPOS_PORT2
I/O
INUSB,
OUSB
AVCCUSB
---
I/O
INUSB,
OUSB
AVCCUSB
---
VIO
A23
O
OPCI
B7
VSS
GND
---
---
---
B8
RD#
O
O3/5
VIO
---
B285
DNEG_PORT2
Strap (See Table 36 on page 58.)
B29
GPIO10
I/O
(PU22.5)
INTS,
O8/8
DSR2#
I
(PU22.5)
INTS
PMR[18] = 1 and
PMR[8] = 0
IDE_IORDY1
I
(PU22.5)
INTS1
PMR[18] = 0 and
PMR[8] = 1
SDTEST1
O
(PU22.5)
O2/5
PMR[18] = 1 and
PMR[8] = 1
---
CLKSEL0
INSTRP
I
(PD100)
B9
WR#
O
O3/5
VIO
B10
VSS
GND
---
---
---
B11
VSYNC
O
O1/4
VIO
---
B12
NC
---
---
---
---
B13
VIO
PWR
---
---
---
B14
VSS
GND
---
---
---
B15
NC
---
---
---
---
B16
VIO
PWR
---
---
---
B175, 2
B185, 2
B19
B20
BUSY/WAIT#
I
INT
TFTD3
O
O1/4
F_C/BE1#
O
O1/4
ACK#
I
INT
B215,2
B22
PMR[23] = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
GND
B31
VIO
PWR
---
---
---
C1
AD26
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
D2
I/O
INPCI,
OPCI
AD24
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
D0
I/O
INPCI,
OPCI
C3
VIO
PWR
---
---
---
C4
AD25
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
D1
I/O
INPCI,
OPCI
GNT0#
O
OPCI
VIO
---
C2
PMR[23]3 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
VIO
PMR[23]3 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
O1/4
PMR[23]3 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
FPCICLK
O
O1/4
PMR[23]3 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
PWR
---
---
SLIN#/ASTRB#
O
O14/14
VIO
TFTD16
O
O1/4
O
VSS
3
O
F_IRDY#
B30
PMR[23]3 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
TFTDE
VIO
5,2
VIO
---
DID0
C6
PMR[23] = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
C7
C8
VIO
ROMCS#
= 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
O
OPCI
Strap (See Table 36 on page 58.)
VIO
INSTRP
I
(PD100)
--Strap (See Table 36 on page 58.)
PWR
---
---
---
O
O3/5
VIO
---
VIO
Strap (See Table 36 on page 58.)
VIO
PMR[9] = 0 and
PMR[4] = 0
INSTRP
I
(PD100)
GPIO19
I/O
(PU22.5)
INTS,
O3/5
INTC#
I
(PU22.5)
INTS
PMR[9] = 0 and
PMR[4] = 1
IOCHRDY
I
(PU22.5)
INTS1
PMR[9] = 1 and
PMR[4] = 1
PWR
---
---
---
VIO
PMR[6] = 0
INIT#
O
O14/14
TFTD5
O
O1/4
PMR[23]3 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
C10
VIO
SMI_O
O
O14/14
3
PMR[23] = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
C11
IRTX
O
O8/8
SOUT3
O
O8/8
---
C12
VSS
GND
---
---
---
VIO
PWR
---
---
---
VSS
GND
---
---
---
VSS
GND
---
VIO
C9
I
INSTRP
(PD100)
---
BOOT16
PMR[23]3
---
PMR[23]3 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
B23
NC
---
---
---
---
C13
B24
VSS
GND
---
---
---
C14
44
GNT1#
DID1
3
PMR[23]3 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
O14/14
C5
---
PMR[18] = 0 and
PMR[8] = 0
PMR[6] = 1
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
Table 3-4.
481-TEPBGA Ball Assignment - Sorted by Ball Number (Continued)
I/O
Buffer1 Power
Rail Configuration
(PU/PD) Type
Ball
No.
Signal Name
C15
VSS
GND
---
---
---
C16
AVSSPLL2
GND
---
---
---
C175,2
SLCT
I
INT
VIO
PMR[23]3 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
TFTD15
O
O1/4
F_C/BE3#
C18
C195,2
C205,2
C215,2
PD4
O
I/O
INT,
O14/14
PMR[23]3 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
VIO
O1/4
PMR[23]3 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
F_AD4
O
O14/14
PMR[23]3 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
PD5
I/O
INT,
O14/14
TFTD11
O
O1/4
PMR[23]3 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
F_AD5
O
O14/14
PMR[23]3 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
INT,
O14/14
TFTD9
O
O1/4
F_AD3
O
O14/14
PD0
I/O
INT,
O14/14
TFTD6
O
O1/4
F_AD0
O
GPIO9
I/O
(PU22.5)
INTS,
O1/4
DCD2#
I
(PU22.5)
INTS
PMR[18] = 1 and
PMR[8] = 0
IDE_IOW1#
O
(PU22.5)
O1/4
PMR[18] = 0 and
PMR[8] = 1
SDTEST2
O
(PU22.5)
O2/5
PMR[18] = 1 and
PMR[8] = 1
PWR
---
---
---
VIO
PMR[17] = 0 and
PMR[8] = 0
VIO
VIO
C30
GPIO7
I/O
(PU22.5)
INTS,
O1/4
RTS2#
O
(PU22.5)
O1/4
PMR[17] = 1 and
PMR[8] = 0
IDE_DACK1#
O
(PU22.5)
O1/4
PMR[17] = 0 and
PMR[8] = 1
SDTEST0
O
(PU22.5)
O2/5
PMR[17] = 1 and
PMR[8] = 1
GPIO8
I/O
(PU22.5)
INTS,
O8/8
CTS2#
I
(PU22.5)
INTS
PMR[17] = 1 and
PMR[8] = 0
IDE_DREQ1
I
(PU22.5)
INTS1
PMR[17] = 0 and
PMR[8] = 1
SDTEST4
O
(PU22.5)
O2/5
PMR[17] = 1 and
PMR[8] = 1
AD21
I/O
INPCI,
OPCI
A21
O
OPCI
AD22
I/O
INPCI,
OPCI
A22
O
OPCI
AD20
I/O
INPCI,
OPCI
A20
O
OPCI
AD27
I/O
INPCI,
OPCI
D3
I/O
INPCI,
OPCI
AD31
I/O
INPCI,
OPCI
D7
I/O
INPCI,
OPCI
PCICLK1
O
OPCI
C31
D1
D2
PMR[23]3
= 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
D3
PMR[23]3 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
VIO
PMR[23]3
= 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
PMR[23]3 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
O14/14
D4
D5
PMR[23]3 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
C22
VIO
PWR
---
---
---
C23
NC
---
---
---
---
C24
NC
---
---
---
---
C25
VIO
PWR
---
---
---
D7
VSS
C26
INTB#
I
(PU22.5)
INPCI
VIO
---
D8
FRAME#
C27
AVSSUSB
GND
---
---
---
D9
AMD Geode™ SC3200 Processor Data Book
PMR[18] = 0 and
PMR[8] = 0
VIO
PMR[23]3 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
PMR[23]3 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
VIO
C29
PMR[23]3 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
O
I/O
C28
PMR[23] = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
TFTD10
PD3
Signal Name
3
O1/4
I/O
Buffer1 Power
Rail Configuration
(PU/PD) Type
Ball
No.
D6
LPC_ROM
VIO
PMR[17] = 0 and
PMR[8] = 0
VIO
Cycle Multiplexed
VIO
Cycle Multiplexed
VIO
Cycle Multiplexed
VIO
Cycle Multiplexed
VIO
Cycle Multiplexed
VIO
---
INSTRP
I
(PD100)
Strap (See Table 36 on page 58.)
GND
---
---
---
I/O
(PU22.5)
INPCI,
OPCI
VIO
---
IOR#
O
O3/5
VIO
PMR[21] = 0 and
PMR[2] = 0
DOCR#
O
O3/5
PMR[21] = 0 and
PMR[2] = 1
GPIO14
I/O
(PU22.5)
INTS,
O3/5
PMR[21] = 1 and
PMR[2] = 1
45
Revision 5.1
Table 3-4.
Signal Definitions
481-TEPBGA Ball Assignment - Sorted by Ball Number (Continued)
I/O
Buffer1 Power
Rail Configuration
(PU/PD) Type
Ball
No.
Signal Name
GPIO1
INT, O3/
I/O
(PU22.5)
5
IOCS1#
O
(PU22.5)
TFTD12
Ball
No.
Signal Name
D10
I/O
Buffer1 Power
Rail Configuration
(PU/PD) Type
I
(PU22.5)
INPCI
VIO
---
PWR
---
---
---
GPIO6
I/O
(PU22.5)
INTS,
O1/4
VIO
PMR[18] = 0 and
PMR[8] = 0
DTR2#/BOUT2
O
(PU22.5)
O1/4
PMR[18] = 1 and
PMR[8] = 0
PMR[12] = 1
IDE_IOR1#
O
(PU22.5)
O1/4
PMR[18] = 0 and
PMR[8] = 1
---
SDTEST5
O
(PU22.5)
O2/5
PMR[18] = 1 and
PMR[8] = 1
O
O8/8
VIO
PMR[23]3 = 0 and
PMR[13] = 0
D26
INTA#
O3/5
VIO
PMR[23]3 = 0 and
PMR[13] = 1
D27
AVCCUSB
D28
O
(PU22.5)
O1/4
VIO
PMR[23]3 = 1
TRDE#
O
O3/5
VIO
PMR[12] = 0
GPIO0
I/O
(PU22.5)
INTS,
O3/5
VIO
D12
VCORE
PWR
---
---
D13
VSS
GND
---
---
---
D14
VIO
PWR
---
---
---
D15
VIO
PWR
---
---
---
D16
NC
---
---
---
---
D30
TDP
I/O
Diode
---
---
I
(PU22.5
PD22.5)
INT
VIO
PMR[23]3 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
(PU/PD under software control.)
D31
TDN
I/O
WIRE
VIO
---
E1
AD16
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
A16
O
OPCI
TFTD14
O
O1/4
PMR[23]3 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
E2
AD19
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
F_C/BE2#
O
O1/4
PMR[23]3 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
A19
O
OPCI
E3
AD18
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
A18
O
OPCI
I/O
(PU22.5)
INPCI,
OPCI
VIO
Cycle Multiplexed
BHE#
O
OPCI
SIN2
I
INTS
VIO
PMR[28] = 0
SDTEST3
O
O2/5
I
(PU22.5)
INPCI
VIO
---
D11
D175, 2 PE
D29
CLKSEL2
D18
VIO
PWR
---
---
---
D19
VSS
GND
---
---
---
I/O
INT,
O14/14
VIO
PMR[23]3 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
D205, 2 PD2
TFTD8
D21
5, 2
O
O1/4
F_AD2
O
O14/14
ERR#
I
INT, O1/
E4
PMR[23]3 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
PMR[23]3 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
VIO
4
3
PMR[23] = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
TFTD4
O
O1/4
PMR[23]3 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
F_C/BE0#
O
O1/4
PMR[23]3
= 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
D225, 2 AFD#/DSTRB#
O
O14/14
TFTD2
O
O1/4
PMR[23]3 = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
INTR_O
O
O14/14
PMR[23]3 = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
VIO
E28
VIO
PWR
---
---
---
D24
NC
---
---
---
---
D25
VSS
GND
---
---
---
DEVSEL#
VIO
INSTRP
I
(PD100)
--Strap (See Table 36 on page 58.)
PMR[28] = 1
E29
TRST#
E30
TDO
O
OPCI
VIO
---
E31
TCK
I
(PU22.5)
INPCI
VIO
---
F1
TRDY#
I/O
(PU22.5)
INPCI,
OPCI
VIO
Cycle Multiplexed
D13
I/O
(PU22.5)
INPCI,
OPCI
IRDY#
I/O
(PU22.5)
INPCI,
OPCI
VIO
Cycle Multiplexed
D14
I/O
(PU22.5)
INPCI,
OPCI
C/BE2#
I/O
(PU22.5)
INPCI,
OPCI
VIO
Cycle Multiplexed
D10
I/O
(PU22.5)
INPCI,
OPCI
AD17
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
A17
O
OPCI
TMS
I
(PU22.5)
INPCI
VIO
---
F2
PMR[23]3 = 0 and
(PMR[27] = 0 and
FPCI_MON = 0)
D23
46
SOUT2
F3
F4
F28
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
Table 3-4.
481-TEPBGA Ball Assignment - Sorted by Ball Number (Continued)
I/O
Buffer1 Power
(PU/PD) Type
Rail Configuration
Ball
No.
Signal Name
F29
TDI
I
(PU22.5)
INPCI
VIO
---
F30
GTEST
I
(PD22.5)
INT
VIO
---
F31
VPCKIN
I
INT
VIO
---
G1
STOP#
I/O
(PU22.5)
INPCI,
OPCI
VIO
Cycle Multiplexed
D15
I/O
(PU22.5)
INPCI,
OPCI
G2
VSS
GND
---
---
---
G3
VIO
PWR
---
---
---
G4
VSS
GND
---
---
---
G28
VSS
GND
---
---
---
G29
VIO
PWR
---
---
---
G30
VSS
GND
---
---
---
I
INT
G31
VPD7
VIO
---
H1
SERR#
INPCI,
I/O
(PU22.5) ODPCI
VIO
---
H2
PERR#
I/O
(PU22.5)
INPCI,
OPCI
VIO
---
H3
LOCK#
I/O
(PU22.5)
INPCI,
OPCI
VIO
---
H4
C/BE3#
I/O
(PU22.5)
INPCI,
OPCI
VIO
Cycle Multiplexed
D11
I/O
(PU22.5)
INPCI,
OPCI
H28
VPD6
I
INT
VIO
---
H29
VPD5
I
INT
VIO
---
H30
VPD4
I
INT
VIO
---
H31
VPD3
I
INT
VIO
---
J1
AD13
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
A13
O
OPCI
C/BE1#
I/O
(PU22.5)
INPCI,
OPCI
D9
I/O
(PU22.5)
INPCI,
OPCI
J2
J3
J4
AD15
I/O
INPCI,
OPCI
A15
O
OPCI
PAR
I/O
(PU22.5)
INPCI,
OPCI
D12
I/O
(PU22.5)
INPCI,
OPCI
VIO
VIO
VIO
Cycle Multiplexed
Cycle Multiplexed
Cycle Multiplexed
Signal Name
J31
GPIO39
I/O
(PU22.5)
INPCI,
OPCI
SERIRQ
I/O
INPCI,
OPCI
AD11
I/O
INPCI,
OPCI
A11
O
OPCI
K1
VPD2
I
INT
VIO
---
J29
VPD1
I
INT
VIO
---
J30
VPD0
I
INT
VIO
---
AMD Geode™ SC3200 Processor Data Book
VIO
PMR[14]4 = 0 and
PMR[22]4 = 0
PMR[14]4 = 1 and
PMR[22]4 = 1
VIO
Cycle Multiplexed
K2
VIO
PWR
---
---
---
K3
VSS
GND
---
---
---
K4
AD14
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
VIO
PMR[14]4 = 0 and
PMR[22]4 = 0. The
IRRX2 input is connected to the input
path of GPIO38.
There is no logic
required to enable
IRRX2, just a simple connection.
Hence, when
GPIO38 is the
selected function,
IRRX2 is also
selected.
A14
K28
GPIO38/IRRX2
LPCPD#
O
OPCI
I/O
(PU22.5)
INPCI,
OPCI
O
OPCI
PMR[14]4 = 1 and
PMR[22]4 = 1
K29
VIO
PWR
---
---
---
K30
VSS
GND
---
---
---
K31
GPIO37
I/O
(PU22.5)
INPCI,
OPCI
VIO
PMR[14]4 = 0 and
PMR[22]4 = 0
O
OPCI
C/BE0#
I/O
(PU22.5)
INPCI,
OPCI
D8
I/O
(PU22.5)
INPCI,
OPCI
I/O
INPCI,
OPCI
LFRAME#
L1
L2
AD9
A9
O
OPCI
AD10
I/O
INPCI,
OPCI
A10
O
OPCI
L4
AD12
I/O
INPCI,
OPCI
O
OPCI
L28
GPIO36
I/O
(PU22.5)
INPCI,
OPCI
LDRQ#
I
INPCI
L3
A12
J28
I/O
Buffer1 Power
Rail Configuration
(PU/PD) Type
Ball
No.
PMR[14]4 = 1 and
PMR[22]4 = 1
VIO
Cycle Multiplexed
VIO
Cycle Multiplexed
VIO
Cycle Multiplexed
VIO
Cycle Multiplexed
VIO
PMR[14]4 = 0 and
PMR[22]4 = 0
PMR[14]4 = 1 and
PMR[22]4 = 1
47
Revision 5.1
Table 3-4.
481-TEPBGA Ball Assignment - Sorted by Ball Number (Continued)
I/O
Buffer1 Power
Rail Configuration
(PU/PD) Type
Ball
No.
Signal Name
L29
GPIO35
I/O
(PU22.5)
INPCI,
OPCI
LAD3
I/O
(PU22.5)
INPCI,
OPCI
GPIO34
I/O
(PU22.5)
INPCI,
OPCI
LAD2
I/O
(PU22.5)
INPCI,
OPCI
GPIO33
I/O
(PU22.5)
INPCI,
OPCI
LAD1
I/O
(PU22.5)
INPCI,
OPCI
L30
L31
Signal Definitions
VIO
PMR[14]4 = 0 and
PMR[22]4 = 0
PMR[14]4 = 0 and
PMR[22]4 = 0
VIO
PMR[14]4 = 0 and
PMR[22]4 = 0
GND
---
---
---
M2
AD7
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
A7
O
OPCI
M3
VIO
PWR
---
---
---
M4
AD8
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
A8
O
OPCI
GPIO32
I/O
(PU22.5)
INPCI,
OPCI
LAD0
I/O
(PU22.5)
INPCI,
OPCI
I/O
(PU22.5)
INAB,
O8/8
VIO
I/O
(PU22.5)
INAB,
OD8
VIO
PMR[19] = 1
PWR
---
---
GPIO13
AB2D
M30
VIO
I/O
INPCI,
OPCI
A5
O
N31
VIO
VIO
O
O3/5
AB1C
I/O
(PU22.5)
INAB,
OD8
GPIO20
INT, O3/
I/O
(PU22.5)
5
IDE_CS1#
O
O1/4
TFTDE
O
O1/4
P3
AD1
I/O
INPCI,
OPCI
PMR[14]4 = 1 and
PMR[22]4 = 1
O
OPCI
P4
VCORE
PWR
PMR[19] = 0
P13
VCORE
P14
VCORE
P15
---
PMR[14]4 = 0 and
PMR[22]4 = 0
Cycle Multiplexed
AD5
IOCS1#
P2
VIO
N3
INT, O3/
I/O
(PU22.5)
5
OPCI
INPCI,
OPCI
OPCI
GPIO1
O
I/O
O
INAB,
OD8
A4
AD3
A6
I/O
(PU22.5)
INPCI,
OPCI
N1
INPCI,
OPCI
AB1D
N30
I/O
---
I/O
INAB,
OD8
AD4
---
AD6
I/O
(PU22.5)
P1
---
N2
AB2C
O3/5
GND
OPCI
INAB,
O8/8
O
VSS
O
I/O
(PU22.5)
DOCCS#
M31
A3
GPIO12
PMR[14]4 = 1 and
PMR[22]4 = 1
VSS
M29
N29
PMR[14]4 = 1 and
PMR[22]4 = 1
M1
M28
Signal Name
PMR[14]4 = 1 and
PMR[22]4 = 1
VIO
Cycle Multiplexed
Cycle Multiplexed
VIO
PMR[19] = 0
PMR[19] = 1
VIO
PMR[23]3 = 0
PMR[23]3 = 1 and
PMR[13] = 0
PMR[23]3 = 1 and
PMR[13] = 1
VIO
PMR[23]3 = 0
PMR[23]3 = 1 and
PMR[7] = 0
PMR[23]3 = 1 and
PMR[7] = 1
VIO
Cycle Multiplexed
VIO
PMR[24] = 0
PMR[24] = 1
VIO
Cycle Multiplexed
---
---
---
PWR
---
---
---
PWR
---
---
---
VSS
GND
---
---
---
P16
VSS
GND
---
---
---
P17
VSS
GND
---
---
---
P18
VCORE
PWR
---
---
---
P19
VCORE
PWR
---
---
---
P28
VCORE
PWR
---
---
---
P29
SDATA_OUT
O
OAC97
VIO
---
I
INSTRP
(PD100)
VIO
Strap (See Table 36 on page 58.)
VIO
---
A1
TFT_PRSNT
VIO
I/O
Buffer1 Power
Rail Configuration
(PU/PD) Type
Ball
No.
P30
SYNC
CLKSEL3
OPCI
O
OAC97
INSTRP
I
(PD100)
Strap (See Table 36 on page 58.)
N4
VSS
GND
---
---
---
P31
AC97_CLK
O
O2/5
VIO
PMR[25] = 1
N13
VCORE
PWR
---
---
---
R1
VSS
GND
---
---
---
N14
VCORE
PWR
---
---
---
R2
VSS
GND
---
---
---
N15
VSS
GND
---
---
---
R3
VSS
GND
---
---
---
N16
VSS
GND
---
---
---
R4
VSS
GND
---
---
---
N17
VSS
GND
---
---
---
R13
VSS
GND
---
---
---
N18
VCORE
PWR
---
---
---
R14
VSS
GND
---
---
---
N19
VCORE
PWR
---
---
---
R15
VSS
GND
---
---
---
N28
VSS
GND
---
---
---
R16
VSS
GND
---
---
---
R17
VSS
GND
---
---
---
48
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
Table 3-4.
481-TEPBGA Ball Assignment - Sorted by Ball Number (Continued)
I/O
Buffer1 Power
Rail Configuration
(PU/PD) Type
Ball
No.
Signal Name
R18
VSS
GND
---
---
---
R19
VSS
GND
---
---
---
R28
VSS
GND
---
---
---
Ball
No.
Signal Name
V1
IDE_DATA15
I/O
Buffer1 Power
(PU/PD) Type
Rail Configuration
I/O
INTS1,
TS1/4
TFTD7
O
O1/4
IDE_DATA14
I/O
INTS1,
TS1/4
TFTD17
O
O1/4
V3
IDE_DATA13
I/O
INTS1,
TS1/4
O
O1/4
V4
VSS
GND
V2
R29
VSS
GND
---
---
---
R30
VSS
GND
---
---
---
R31
VSS
GND
---
---
---
T1
VCORE
PWR
---
---
---
T2
VCORE
PWR
---
---
---
T3
VCORE
PWR
---
---
---
T4
VCORE
PWR
---
---
---
V13
VCORE
T13
VSS
GND
---
---
---
V14
VCORE
T14
VSS
GND
---
---
---
V15
VIO
PMR[24] = 0
PMR[24] = 1
VIO
PMR[24] = 0
PMR[24] = 1
VIO
PMR[24] = 0
---
---
---
PWR
---
---
---
PWR
---
---
---
VSS
GND
---
---
---
VSS
GND
---
---
---
VSS
GND
---
---
---
TFTD15
PMR[24] = 1
T15
VSS
GND
---
---
---
V16
T16
VSS
GND
---
---
---
V17
T17
VSS
GND
---
---
---
V18
VCORE
PWR
---
---
---
T18
VSS
GND
---
---
---
V19
VCORE
PWR
---
---
---
T19
VSS
GND
---
---
---
V28
VSS
GND
---
---
---
T28
VCORE
PWR
---
---
---
V29
SDCLK3
O
O2/5
VIO
---
T29
VCORE
PWR
---
---
---
V30
GXCLK
O
O2/5
VIO
T30
VCORE
PWR
---
---
---
PMR[23]3 = 0 and
PMR[29] = 0
T31
VCORE
PWR
---
---
---
FP_VDD_ON
O
O1/4
PMR[23]3 = 1
U1
AD0
I/O
INPCI,
OPCI
VIO
Cycle Multiplexed
TEST3
O
O2/5
PMR[23]3 = 0 and
PMR[29] = 1
A0
O
OPCI
IDE_ADDR2
O
O1/4
TFTD4
O
O1/4
AD2
I/O
INPCI,
OPCI
U2
U3
A2
O
OPCI
V31
VIO
PMR[24] = 0
GPIO16
PC_BEEP
INT, O2/
I/O
(PU22.5)
5
O
O2/5
VIO
PMR[0] = 1 = 0 and
FPCI_MON = 0
PMR[24] = 1
VIO
F_DEVSEL#
PMR[0] = 0 and
FPCI_MON = 0
FPCI_MON = 1
O
O2/5
W1
VIO
PWR
---
---
---
W2
VSS
GND
---
---
---
W3
IDE_DATA12
I/O
INTS1,
TS1/4
VIO
PMR[24] = 0
TFTD13
O
O1/4
IDE_DATA11
I/O
INTS1,
TS1/4
GPIO41
I/O
INTS1,
O1/4
Cycle Multiplexed
U4
VCORE
PWR
---
---
---
U13
VSS
GND
---
---
---
U14
VSS
GND
---
---
---
U15
VSS
GND
---
---
---
U16
VSS
GND
---
---
---
U17
VSS
GND
---
---
---
U18
VSS
GND
---
---
---
W13
VCORE
PWR
---
---
---
VCORE
PWR
---
---
---
W4
PMR[24] = 1
VIO
PMR[24] = 0
PMR[24] = 1
U19
VSS
GND
---
---
---
W14
U28
VCORE
PWR
---
---
---
W15
VSS
GND
---
---
---
FPCI_MON = 0
W16
VSS
GND
---
---
---
FPCI_MON = 1
W17
VSS
GND
---
---
---
U29
U30
U31
AC97_RST#
O
O2/5
F_STOP#
O
O2/5
BIT_CLK
I
INT
F_TRDY#
O
O1/4
SDATA_IN
I
INT
F_GNT0#
O
O2/5
VIO
VIO
VIO
AMD Geode™ SC3200 Processor Data Book
FPCI_MON = 0
W18
VCORE
PWR
---
---
---
FPCI_MON = 1
W19
VCORE
PWR
---
---
---
FPCI_MON = 0
W285
MD57
I/O
INT,
TS2/5
VIO
---
W29
SDCLK1
O
O2/5
VIO
---
FPCI_MON = 1
49
Revision 5.1
Table 3-4.
Signal Definitions
481-TEPBGA Ball Assignment - Sorted by Ball Number (Continued)
I/O
Buffer1 Power
Rail Configuration
(PU/PD) Type
I/O
Buffer1 Power
Rail Configuration
(PU/PD) Type
Ball
No.
Signal Name
W30
VSS
GND
---
---
---
AB31
DQM7
O
O2/5
VIO
---
W31
VIO
PWR
---
---
---
AC1
IDE_DATA1
I/O
VIO
PMR[24] = 0
Y1
IDE_DATA10
I/O
INTS1,
TS1/4
VIO
PMR[24] = 0
INTS1,
TS1/4
TFTD16
O
O1/4
AC2
IDE_DATA2
I/O
INTS1,
TS1/4
TFTD14
O
O1/4
AC3
IDE_DATA0
I/O
INTS1,
TS1/4
TFTD6
O
O1/4
IDE_DREQ0
I
INTS1
TFTD8
O
O1/4
AC285
MD25
I/O
INT,
TS2/5
VIO
---
AC295
MD26
I/O
INT,
TS2/5
VIO
---
AC305
MD27
I/O
INT,
TS2/5
VIO
---
AC31
DQM3
O
O2/5
VIO
---
AD1
IDE_IORDY0
I
INTS1
VIO
PMR[24] = 0
Y2
IDE_DATA9
I/O
INTS1,
TS1/4
VIO
PMR[24] = 0
Y3
IDE_DATA8
I/O
INTS1,
TS1/4
VIO
PMR[24] = 0
GPIO40
I/O
INTS1,
O1/4
IDE_IOR0#
O
O1/4
TFTD10
O
O1/4
Y285
MD58
I/O
INT,
TS2/5
VIO
---
Y295
MD59
I/O
INT,
TS2/5
VIO
---
Y305
MD60
I/O
INT,
TS2/5
VIO
---
Y315
MD56
I/O
INT,
TS2/5
VIO
---
Y4
AA1
AA2
IDE_RST#
O
O1/4
TFTDCK
O
O1/4
IDE_DATA7
VIO
PMR[24] = 0
VIO
PMR[24] = 0
PMR[24] = 1
I
INTS
I/O
INTS1,
TS1/4
I
INTS1
IDE_DATA5
I/O
INTS1,
TS1/4
CLK27M
O
O1/4
AA28
SDCLK2
O
O2/5
VIO
---
AA295
MD61
I/O
INT,
TS2/5
VIO
AA305
MD62
I/O
INT,
TS2/5
AA315
MD63
I/O
AB1
IDE_DATA4
FP_VDD_ON
IDE_DATA6
IRQ9
AA4
AB2
VSS
AB3
VIO
AB4
IDE_DATA3
VIO
PMR[24] = 0
AD2
TFTD11
O
O1/4
IDE_IOW0#
O
O1/4
PMR[24] = 1
VIO
PMR[24] = 0
PMR[24] = 1
VIO
PMR[24] = 0
PMR[24] = 1
VIO
PMR[24] = 0
PMR[24] = 1
PMR[24] = 1
VIO
PMR[24] = 0
TFTD9
O
O1/4
IDE_ADDR0
O
O1/4
TFTD3
O
O1/4
IDE_DACK0#
O
O1/4
TFTD0
O
O1/4
AD285
MD52
I/O
INT,
TS2/5
VIO
---
AD295
MD29
I/O
INT,
TS2/5
VIO
---
---
AD305
MD30
I/O
INT,
TS2/5
VIO
---
VIO
---
AD315
MD31
I/O
INT,
TS2/5
VIO
---
INT,
TS2/5
VIO
---
AE1
IDE_ADDR1
O
O1/4
VIO
PMR[24] = 0
O
O1/4
I/O
INTS1,
TS1/4
VIO
PMR[24] = 0
AE2
VSS
GND
---
---
---
O
O1/4
AE3
VIO
PWR
---
---
---
GND
---
AE4
VSS
GND
---
---
---
AE28
VSS
GND
---
---
---
PMR[24] = 1
VIO
AD3
PMR[24] = 0
AD4
PMR[24] = 1
VIO
PMR[24] = 0
PMR[24] = 1
TFTD2
PMR[24] = 1
---
---
PWR
---
---
---
I/O
INTS1,
TS1/4
VIO
PMR[24] = 0
TFTD12
O
O1/4
AB285
MD24
I/O
INT,
TS2/5
VIO
---
AB29
VIO
PWR
---
---
---
AB30
VSS
GND
---
---
---
50
AC4
PMR[24] = 1
INTS1,
TS1/4
AA3
Signal Name
PMR[24] = 1
I/O
INTD#
Ball
No.
PMR[24] = 1
PMR[24] = 1
VIO
PMR[24] = 0
PMR[24] = 1
VIO
PMR[24] = 0
PMR[24] = 1
PMR[24] = 1
AE29
VIO
PWR
---
---
---
AE30
VSS
GND
---
---
---
AE315
MD28
I/O
INT,
TS2/5
VIO
---
AF1
IRQ14
I
INTS1
VIO
PMR[24] = 0
TFTD1
O
O1/4
PMR[24] = 1
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
Table 3-4.
481-TEPBGA Ball Assignment - Sorted by Ball Number (Continued)
I/O
Buffer1 Power
Rail Configuration
(PU/PD) Type
Ball
No.
Signal Name
AF2
IDE_CS0#
O
O1/4
TFTD5
O
O1/4
SOUT1
O
O8/8
AF3
CLKSEL1
AF4
OVER_CUR#
AF285
MD50
VIO
PMR[24] = 0
PMR[24] = 1
VIO
I
INSTRP
(PD100)
Strap (See Table 36 on page 58.)
I
INTS
VIO
---
I/O
INT,
TS2/5
VIO
---
AF29
MD49
I/O
INT,
TS2/5
VIO
---
AF30
5
MD54
I/O
INT,
TS2/5
VIO
---
I/O
INT,
TS2/5
VIO
---
I/O
(PU22.5)
INTS,
O8/8
VIO
PMR[16] = 0
MD53
AG1
GPIO18
DTR1#/BOUT1
O
(PU22.5)
O8/8
PMR[16] =1
AG2
SIN1
I
INTS
VIO
---
AG3
X27I
I
WIRE
VIO
---
AG4
TEST1
O
O2/5
VIO
PMR[29] = 1
PLL6B
I/O
INTS,
TS2/5
AG285
MD21
AG29
DQM6
AG30
VIO
---
O
O2/5
VIO
---
DQM2
O
O2/5
VIO
---
AG315
MD55
I/O
INT,
TS2/5
VIO
---
AH1
POWER_EN
O
O1/4
VIO
---
AH2
X27O
O
WIRE
VIO
---
AH3
TEST0
O
O2/5
VIO
PMR[29] = 1
AH4
VIO
AH5
PWRBTN#
AH6
GPWIO0
I/O
MA1
O
O2/5
VIO
---
5
MD34
I/O
INT,
TS2/5
VIO
---
AH175
MD37
I/O
INT,
TS2/5
VIO
---
AH18
VIO
PWR
---
---
---
AH19
VSS
GND
---
---
---
AH205
MD41
I/O
INT,
TS2/5
VIO
---
AH21
MA9
O
O2/5
VIO
---
AH22
MA8
O
O2/5
VIO
---
AH23
DQM1
O
O2/5
VIO
---
AH245
MD13
I/O
INT,
TS2/5
VIO
---
AH16
AH25
VSS
AH26
MA11
AH27
AH285
GND
---
---
---
O
O2/5
VIO
---
CS1#
O
O2/5
VIO
---
MD18
I/O
INT,
TS2/5
VIO
---
AH295
MD48
I/O
INT,
TS2/5
VIO
---
AH305
MD20
I/O
INT,
TS2/5
VIO
---
AH315
MD51
I/O
INT,
TS2/5
VIO
---
AJ1
TEST2
O
O2/5
VIO
PMR[29] = 1
PLL5B
I/O
INT,
TS2/5
INT,
TS2/5
PMR[29] = 0
PWR
---
---
---
I
(PU100)
INBTN
VSB
---
I/O
(PU100)
INTS,
TS2/14
VSB
VSS
GND
---
---
---
CLK32
O
O2/5
VSB
---
POR#
I
INTS
VIO
---
AH10
5
MD3
I/O
INT,
TS2/5
VIO
---
AH11
5
MD5
I/O
INT,
TS2/5
VIO
---
AH12
WEA#
O
O2/5
VIO
---
AH13
VSS
GND
---
---
---
AH14
VIO
PWR
---
---
---
AMD Geode™ SC3200 Processor Data Book
X32I
I
WIRE
VBAT
---
AJ3
X32O
O
WIRE
VBAT
---
VPLL3
PWR
---
---
---
ONCTL#
O
OD14
VSB
---
AJ6
GPWIO2
I/O
(PU100)
INTS,
TS2/14
VSB
---
AJ7
VIO
PWR
---
---
---
AJ8
GPIO11
I/O
(PU22.5)
INTS,
O8/8
VIO
PMR[18] = 0 and
PMR[8] = 0
RI2#
I
(PU22.5)
INTS
PMR[18] = 1 and
PMR[8] = 0
IRQ15
I
(PU22.5)
INTS1
PMR[18] = 0 and
PMR[8] = 1
I/O
INT,
TS2/5
VIO
---
PWR
---
---
---
AJ5
5, 2
---
AH8
PMR[29] = 0
AJ2
AJ4
AH7
AH9
AH15
I/O
Buffer1 Power
Rail Configuration
(PU/PD) Type
PMR[29] = 0
INT,
TS2/5
PLL2B
I/O
Signal Name
---
5
AF315
Ball
No.
AJ95
MD0
AJ10
VIO
AJ115
MD6
I/O
INT,
TS2/5
VIO
---
AJ12
CASA#
O
O2/5
VIO
---
AJ13
BA0
O
O2/5
VIO
---
AJ14
MA10
O
O2/5
VIO
---
51
Revision 5.1
Table 3-4.
Signal Definitions
481-TEPBGA Ball Assignment - Sorted by Ball Number (Continued)
I/O
Buffer1 Power
Rail Configuration
(PU/PD) Type
Ball
No.
Signal Name
AJ155
MD32
I/O
INT,
TS2/5
VIO
AJ165
MD33
I/O
INT,
TS2/5
AJ175
MD36
I/O
Signal Name
---
AK175
MD35
I/O
INT,
TS2/5
VIO
---
VIO
---
AK185
MD46
I/O
INT,
TS2/5
VIO
---
INT,
TS2/5
VIO
---
AK19
VIO
PWR
---
---
---
AK205
MD43
I/O
INT,
TS2/5
VIO
---
AK21
DQM5
O
O2/5
VIO
---
AK22
VSS
GND
---
---
---
AK23
MA5
O
O2/5
VIO
---
AK245
MD15
I/O
INT,
TS2/5
VIO
---
AK25
VSS
AJ185
MD47
I/O
INT,
TS2/5
VIO
---
AJ195
MD45
I/O
INT,
TS2/5
VIO
---
AJ205
MD42
AJ21
SDCLK0
AJ22
VIO
AJ23
MA6
AJ24
AJ25
AJ265
MD11
I/O
I/O
Buffer1 Power
Rail Configuration
(PU/PD) Type
Ball
No.
INT,
TS2/5
VIO
---
O
O2/5
VIO
---
PWR
---
---
---
O
O2/5
VIO
MA3
O
O2/5
VIO
---
VIO
PWR
---
---
---
I/O
INT,
TS2/5
VIO
---
I
INT
VIO
---
I/O
INT,
TS2/5
VIO
---
PWR
---
---
---
---
GND
---
---
---
5
MD14
I/O
INT,
TS2/5
VIO
---
AK275
MD12
I/O
INT,
TS2/5
VIO
---
AK28
SDCLK_OUT
O
O2/5
VIO
---
MD16
I/O
INT,
TS2/5
VIO
---
AK26
AK29
AJ27
SDCLK_IN
AJ285
MD19
AJ29
VIO
AJ305
MD22
I/O
INT,
TS2/5
VIO
---
AJ315
MD17
I/O
INT,
TS2/5
VIO
---
5
AK30
VSS
GND
---
---
---
AK31
VIO
PWR
---
---
---
AL1
VSS
GND
---
---
---
AL2
VIO
PWR
---
---
---
AL3
VBAT
PWR
---
---
---
AL4
LED#
O
OD14
VSB
---
AK1
VIO
PWR
---
---
---
AL5
VSB
PWR
---
---
---
AK2
VSS
GND
---
---
---
AL6
VSBL
PWR
---
---
---
AK3
AVSSPLL3
GND
---
---
---
AL75, 2
PWRCNT2
O
OD14
VSB
---
AK4
THRM#
I
INTS
VSB
---
AL8
SDATA_IN2
I
INTS
VSB
AK5
GPWIO1
I/O
(PU100)
INTs,
TS2/14
VSB
---
F3BAR0+Memory
Offset 08h[21] = 1
AL95
MD2
I/O
VIO
---
O
OD14
VSB
---
INT,
TS2/5
I/O
---
---
INT,
TS2/5
VIO
---
---
AL105
MD4
GND
AK65, 2 PWRCNT1
AK7
VSS
AK8
IRRX1
I
INTS
VSB
PMR[6] = 0
AL11
DQM0
O
O2/5
VIO
---
SIN3
I
INTS
VIO
PMR[6] =1
AL12
CS0#
O
O2/5
VIO
---
MD1
I/O
INT,
TS2/5
VIO
---
AL13
VSS
GND
---
---
---
AL14
MA0
O
O2/5
VIO
---
AL15
DQM4
O
O2/5
VIO
---
AK9
5
AK10
VSS
GND
---
---
---
AK115
MD7
I/O
INT,
TS2/5
VIO
---
AK12
RASA#
AK13
AL16
VSS
GND
---
---
---
5
MD38
I/O
INT,
TS2/5
VIO
---
AL185
MD39
I/O
INT,
TS2/5
VIO
---
GND
---
---
---
I/O
INT,
TS2/5
VIO
---
O
O2/5
VIO
---
VIO
PWR
---
---
---
AK14
BA1
O
O2/5
VIO
---
AK15
MA2
O
O2/5
VIO
---
AL19
VSS
AK16
VIO
PWR
---
---
AL205
MD44
52
AL17
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
Table 3-4.
Ball
No.
Signal Name
AL215
MD40
481-TEPBGA Ball Assignment - Sorted by Ball Number (Continued)
I/O
Buffer1 Power
Rail Configuration
(PU/PD) Type
I/O
Ball
No.
Signal Name
INT,
TS2/5
VIO
---
AL295
MD23
I/O
Buffer1 Power
Rail Configuration
(PU/PD) Type
I/O
INT,
TS2/5
VIO
---
AL22
CKEA
O
O2/5
VIO
---
AL30
VIO
PWR
---
---
---
AL23
MA7
O
O2/5
VIO
---
AL31
VSS
GND
---
---
---
MA4
O
O2/5
VIO
---
1.
MD8
I/O
INT,
TS2/5
VIO
---
AL265
MD10
I/O
INT,
TS2/5
VIO
---
AL275
MD9
I/O
INT,
TS2/5
VIO
---
AL28
MA12
O
O2/5
VIO
---
AL24
AL25
5
2.
3.
4.
5.
AMD Geode™ SC3200 Processor Data Book
For Buffer Type definitions, refer to Table 9-10 "Buffer Types" on page
375.
Is 5V tolerant (ACK#, AFD#/DSTRB#, BUSY/WAIT#, ERR#, INIT#,
PD[7:0], PE, SLCT, SLIN#/ASTRB#, STB#/WRITE#, ONCTL#,
PWRCNT[2:1]).
The TFT_PRSNT strap determines the power-on reset (POR) state of
PMR[23].
The LPC_ROM strap determines the power-on reset (POR) state of
PMR[14] and PMR[22].
Is back-drive protected (MD[63:0], DPOS_PORT1, DNEG_PORT1,
DPOS_PORT2, DNEG_PORT2, DPOS_PORT3, DNEG_PORT3,
ACK#, AFD#/DSTRB#, BUSY/WAIT#, ERR#, INIT#, PD[7:0], PE,
SLCT, SLIN#/ASTRB#, STB#/WRITE#, ONCTL#, PWRCNT[2:1]).
53
Revision 5.1
Signal Definitions
Table 3-5. 481-TEPBGA Ball Assignment - Sorted Alphabetically by Signal Name
Signal Name
Ball No.
Signal Name
U1
AD18
A1
P3
A2
U3
A3
A4
Ball No.
Signal Name
Ball No.
E3
D8
AD19
E2
D9
J2
AD20
D3
D10
F3
N1
AD21
D1
D11
H4
P1
AD22
D2
D12
J4
A5
N3
AD23
B6
D13
F1
A6
N2
AD24
C2
D14
F2
A7
M2
AD25
C4
D15
G1
A8
M4
AD26
C1
DCD2#
C28
A9
L2
AD27
D4
DEVSEL#
E4
A10
L3
AD28
B4
DID0
C5
A11
K1
AD29
B3
DID1
C6
A12
L4
AD30
A3
DNEG_PORT1
A29
A13
J1
AD31
D5
DNEG_PORT2
B28
A14
K4
AFD#/DSTRB#
D22
DNEG_PORT3
A15
J3
AVCCUSB
D27
DOCCS#
A16
E1
AVSSPLL2
C16
DOCR#
A17
F4
AVSSPLL3
AK3
DOCW#
A8
A18
E3
DPOS_PORT1
A28
A19
E2
DPOS_PORT2
B27
A20
D3
DPOS_PORT3
A26
A21
D1
A22
D2
A23
B6
A0
AB1C
N31
AB1D
N30
AB2C
N29
AB2D
M29
AC97_CLK
P31
AC97_RST#
U29
ACK#
B18
AD0
U1
AD1
P3
AD2
U3
AD3
N1
AD4
P1
AD5
N3
AD6
N2
AD7
M2
AD8
M4
AD9
L2
AD10
L3
AD11
K1
AD12
L4
AD13
J1
AD14
K4
AD15
J3
AD16
E1
AD17
F4
54
AVSSUSB
C27
BA0
AJ13
BA1
AK14
BHE#
E4
BIT_CLK
U30
BOOT16
C8
BUSY/WAIT#
B17
C/BE0#
L1
C/BE1#
J2
C/BE2#
F3
C/BE3#
H4
CASA#
AJ12
CKEA
AL22
CLK27M
AA4
CLK32
AH8
CLKSEL0
B8
CLKSEL1
AF3
CLKSEL2
D29
CLKSEL3
P30
CS0#
AL12
CS1#
AH27
CTS2#
C31
D0
C2
D1
C4
D2
C1
D3
D4
D4
B4
D5
B3
D6
A3
D7
D5
L1
A27
A9, N31
D9
DQM0
AL11
DQM1
AH23
DQM2
AG30
DQM3
AC31
DQM4
AL15
DQM5
AK21
DQM6
AG29
DQM7
AB31
DSR2#
B29
DTR1#/BOUT1
AG1
DTR2#/BOUT2
D28
ERR#
D21
F_AD0
C21
F_AD1
A21
F_AD2
D20
F_AD3
C20
F_AD4
C18
F_AD5
C19
F_AD6
A20
F_AD7
A18
F_C/BE0#
D21
F_C/BE1#
B17
F_C/BE2#
D17
F_C/BE3#
C17
F_DEVSEL#
V31
F_FRAME#
A22
F_GNT0#
U31
F_IRDY#
B20
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
Table 3-5.
Signal Name
F_STOP#
F_TRDY#
481-TEPBGA Ball Assignment - Sorted Alphabetically by Signal Name (Continued)
Ball No.
Signal Name
Ball No.
Signal Name
U29
IDE_DATA1
AC1
LOCK#
Ball No.
H3
U30
IDE_DATA2
AC2
LPC_ROM
D6
V30, AB1
IDE_DATA3
AB4
LPCPD#
K28
FPCI_MON
A4
IDE_DATA4
AB1
MA0
AL14
FPCICLK
B18
IDE_DATA5
AA4
MA1
AH15
FRAME#
D8
IDE_DATA6
AA3
MA2
AK15
GNT0#
C5
IDE_DATA7
AA2
MA3
AJ24
GNT1#
C6
IDE_DATA8
Y3
MA4
AL24
GPIO0
D11
IDE_DATA9
Y2
MA5
AK23
GPIO1
D10, N30
IDE_DATA10
Y1
MA6
AJ23
GPIO6
D28
IDE_DATA11
W4
MA7
AL23
GPIO7
C30
IDE_DATA12
W3
MA8
AH22
GPIO8
C31
IDE_DATA13
V3
MA9
AH21
GPIO9
C28
IDE_DATA14
V2
MA10
AJ14
GPIO10
B29
IDE_DATA15
V1
MA11
AH26
GPIO11
AJ8
IDE_DREQ0
AC4
MA12
AL28
GPIO12
N29
IDE_DREQ1
C31
MD0
AJ9
GPIO13
M29
IDE_IOR0#
Y4
MD1
AK9
GPIO14
D9
IDE_IOR1#
D28
MD2
AL9
GPIO15
A8
IDE_IORDY0
AD1
MD3
AH10
GPIO16
V31
IDE_IORDY1
B29
MD4
AL10
GPIO17
A10
IDE_IOW0#
AD2
MD5
AH11
GPIO18
AG1
IDE_IOW1#
C28
MD6
AJ11
GPIO19
C9
IDE_RST#
AA1
MD7
AK11
GPIO20
A9, N31
INIT#
B21
MD8
AL25
GPIO32
M28
INTA#
D26
MD9
AL27
GPIO33
L31
INTB#
C26
MD10
AL26
GPIO34
L30
INTC#
C9
MD11
AJ26
GPIO35
L29
INTD#
AA2
MD12
AK27
GPIO36
L28
INTR_O
D22
MD13
AH24
GPIO37
K31
IOCHRDY
C9
MD14
AK26
GPIO38/IRRX2
K28
IOCS0#
A10
MD15
AK24
GPIO39
J31
IOCS1#
D10
MD16
AK29
GPIO40
Y3
IOCS1#
N30
MD17
AJ31
GPIO41
W4
IOR#
D9
MD18
AH28
GPWIO0
AH6
IOW#
A8
MD19
AJ28
GPWIO1
AK5
IRDY#
F2
MD20
AH30
GPWIO2
AJ6
IRQ9
AA3
MD21
AG28
GTEST
F30
IRQ14
AF1
MD22
AJ30
GXCLK
V30
IRQ15
AJ8
MD23
AL29
HSYNC
A11
IRRX1
AK8
MD24
AB28
IDE_ADDR0
AD3
IRTX
C11
MD25
AC28
IDE_ADDR1
AE1
LAD0
M28
MD26
AC29
IDE_ADDR2
U2
LAD1
L31
MD27
AC30
IDE_CS0#
AF2
LAD2
L30
MD28
AE31
P2
FP_VDD_ON
IDE_CS1#
LAD3
L29
MD29
AD29
IDE_DACK0#
AD4
LDRQ#
L28
MD30
AD30
IDE_DACK1#
C30
LED#
AL4
MD31
AD31
IDE_DATA0
AC3
LFRAME#
K31
MD32
AJ15
AMD Geode™ SC3200 Processor Data Book
55
Revision 5.1
Table 3-5.
Signal Definitions
481-TEPBGA Ball Assignment - Sorted Alphabetically by Signal Name (Continued)
Ball No.
Signal Name
Ball No.
MD33
AJ16
PD4
C18
STB#/WRITE#
A22
MD34
AH16
PD5
C19
STOP#
G1
MD35
AK17
PD6
A20
SYNC
P30
MD36
AJ17
PD7
A18
TCK
E31
MD37
AH17
PE
D17
TDI
F29
MD38
AL17
PERR#
H2
TDN
D31
MD39
AL18
PLL2B
AH3
TDO
E30
MD40
AL21
PLL5B
AJ1
TDP
D30
MD41
AH20
PLL6B
AG4
TEST0
AH3
MD42
AJ20
POR#
AH9
TEST1
AG4
MD43
AK20
POWER_EN
AH1
TEST2
AJ1
MD44
AL20
PWRBTN#
AH5
TEST3
V30
MD45
AJ19
PWRCNT1
AK6
TFT_PRSNT
P29
MD46
AK18
PWRCNT2
MD47
AJ18
RASA#
MD48
AH29
MD49
AF29
MD50
AF28
MD51
AH31
MD52
AD28
MD53
AF31
MD54
MD55
MD56
Y31
MD57
W28
MD58
MD59
Signal Name
Ball No.
Signal Name
AL7
TFTD0
A9, AD4
AK12
TFTD1
A20, AF1
RD#
B8
TFTD2
D22, AE1
REQ0#
B5
TFTD3
B17, AD3
REQ1#
A5
TFTD4
D21, U2
RI2#
AJ8
TFTD5
B21, AF2
ROMCS#
C8
TFTD6
C21, AC3
RTS2#
C30
TFTD7
A21, V1
AF30
SDATA_IN
U31
TFTD8
D20, AC4
AG31
SDATA_IN2
AL8
TFTD9
C20, AD2
SDATA_OUT
P29
TFTD10
C18, Y4
SDCLK_IN
AJ27
TFTD11
C19, AD1
Y28
SDCLK_OUT
AK28
TFTD12
D10, AB4
Y29
SDCLK0
AJ21
TFTD13
A18, W3
MD60
Y30
SDCLK1
W29
TFTD14
D17, AC2
MD61
AA29
SDCLK2
AA28
TFTD15
C17, V3
MD62
AA30
SDCLK3
V29
TFTD16
B20, AC1
MD63
AA31
SDTEST0
C30
TFTD17
A22, V2
SDTEST1
B29
TFTDCK
A10, AA1
SDTEST2
C28
TFTDE
B18, P2
SDTEST3
E28
THRM#
AK4
SDTEST4
C31
TMS
F28
NC (Total of 13)
A14, A15, A23,
A24, A25, B12,
B15, B23, B26,
C23, C24, D16,
D24
ONCTL#
AJ5
SDTEST5
D28
TRDE#
D11
OVER_CUR#
AF4
SERIRQ
J31
TRDY#
F1
J4
SERR#
H1
TRST#
E29
AG2
VBAT
AL3
SIN2
E28
VCORE (Total of 29)
A4
SIN3
AK8
PCICLK1
D6
SLCT
C17
PCIRST#
A6
SLIN#/ASTRB#
B20
PAR
PC_BEEP
V31
SIN1
PCICLK
A7
PCICLK0
C21
SMI_O
B21
PD1
A21
SOUT1
AF3
PD2
D20
SOUT2
D29
PD3
C20
SOUT3
C11
PD0
56
D12, N13, N14,
N18, N19, P4,
P13, P14, P18,
P19, P28, T1, T2,
T3, T4, T28, T29,
T30, T31, U4,
U28, V13, V14,
V18, V19, W13,
W14, W18, W19
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
Table 3-5.
Signal Name
VIO (Total of 46)
481-TEPBGA Ball Assignment - Sorted Alphabetically by Signal Name (Continued)
Ball No.
A2, A12, A30, B2,
B13, B16, B19,
B31, C3, C7,
C10, C13, C22,
C25, C29, D14,
D15, D18, D23,
G3, G29, K2,
K29, M3, M30,
W1, W31, AB3,
AB29, AE3,
AE29, AH4,
AH14, AH18,
AJ7, AJ10, AJ22,
AJ25, AJ29, AK1,
AK13, AK16,
AK19, AK31,
AL2, AL30
VPCKIN
F31
VPD0
J30
VPD1
J29
VPD2
J28
VPD3
H31
VPD4
H30
VPD5
H29
VPD6
H28
VPD7
G31
VPLL2
A17
VPLL3
AJ4
VSB
AL5
VSBL
AL6
AMD Geode™ SC3200 Processor Data Book
Signal Name
VSS (Total of 96)
VSYNC
Ball No.
A1, A13, A16,
A19, A31, B1, B7,
B10, B14, B22,
B24, B25, B30,
C12, C14, C15,
D7, D13, D19,
D25, G2, G4,
G28, G30, K3,
K30, M1, M31,
N4, N15, N16,
N17, N28, P15,
P16, P17, R1, R2,
R3, R4, R13,
R14, R15, R16,
R17, R18, R19,
R28, R29, R30,
R31, T13, T14,
T15, T16, T17,
T18, T19, U13,
U14, U15, U16,
U17, U18, U19,
V4, V15, V16,
V17, V28, W2,
W15, W16, W17,
W30, AB2, AB30,
AE2, AE4, AE28,
AE30, AH7,
AH13, AH19,
AH25, AK2, AK7,
AK10, AK22,
AK25, AK30,
AL1, AL13, AL16,
AL19, AL31
Signal Name
WEA#
Ball No.
AH12
WR#
B9
X27I
AG3
X27O
AH2
X32I
AJ2
X32O
AJ3
B11
57
Revision 5.1
3.2
Signal Definitions
Strap Options
Several balls are read at power-up that set up the state of
the SC3200. These balls are typically multiplexed with
other functions that are outputs after the power-up
sequence is complete. The SC3200 must read the state of
the balls at power-up and the internal PU or PD resistors
do not guarantee the correct state will be read. Therefore, it
is required that an external PU or PD resistor with a value
of 1.5 KΩ be placed on the balls listed in Table 3-6. The
value of the resistor is important to ensure that the proper
state is read during the power-up sequence. If the ball is
not read correctly at power-up, the SC3200 may default to
a state that causes it to function improperly, possibly resulting in application failure.
Table 3-6. Strap Options
Ball No.
Strap
Option
Muxed With
CLKSEL0
RD#
CLKSEL1
SOUT1
EBGA
TEPBGA
Nominal
Internal
PU or PD
F3
B8
PD100
B27
AF3
PD100
CLKSEL2
SOUT2
AK3
D29
PD100
CLKSEL3
SYNC
AL13
P30
PD100
External PU/PD Strap Settings
Strap = 0 (PD)
Strap = 1 (PU)
See Table 4-7 on page 101 for
CLKSEL strap options.
Register References
GCB+I/O Offset 1Eh[9:8] (aka
CCFC register bits [9:8]) (RO):
Value programmed at reset by
CLKSEL[1:0].
GCB+I/O Offset 10h[3:0] (aka
MCCM register bits [3:0]) (RO):
Value programmed at reset by
CLKSEL[3:0].
GCB+I/O Offset 1Eh[3:0] (aka
CCFC register bits [3:0]) (R/W,
but write not recommended):
Value programmed at reset by
CLKSEL[3:0].
Note: Values for GCB+I/O Offset 10h[3:0] and 1Eh[3:0] are not
the same.
BOOT16
ROMCS#
G4
C8
PD100
Enable boot
from 8-bit ROM
Enable boot
from 16-bit
ROM
GCB+I/O Offset 34h[3] (aka MCR
register bit 3) (RO): Reads back
strap setting.
GCB+I/O Offset 34h[14] (R/W):
Used to allow the ROMCS# width
to be changed under program
control.
TFT_PRSNT
SDATA_OU
T
AK13
P29
PD100
TFT not muxed
onto Parallel
Port
TFT muxed
onto Parallel
Port
GCB+I/O Offset 30h[23] (aka
PMR register bit 23) (R/W):
Reads back strap setting.
LPC_ROM
PCICLK1
E4
D6
PD100
Disable boot
from ROM on
LPC bus
Enable boot
from ROM on
LPC bus
F0BAR1+I/O Offset 10h[15] (R/
W): Reads back strap setting and
allows LPC ROM to be changed
under program control.
FPCI_MON
PCICLK0
D3
A4
PD100
Disable FastPCI, INTR_O,
and SMI_O
monitoring signals.
Enable FastPCI, INTR_O,
and SMI_O
monitoring signals. (Useful
during debug.)
GCB+I/O Offset 34h[30] (aka
MCR register bit 30) (RO): Reads
back strap setting.
Defines the system-level chip ID.
GCB+I/O Offset 34h[31,29] (aka
MCR register bits 31 and 29)
(RO): Reads back strap setting.
DID0
GNT0#
D4
C5
PD100
DID1
GNT1#
D2
C6
PD100
Note:
Note:
Note:
For normal operation,
strap this signal low
using a 1.5 KΩ resistor.
GNT0# must have a PU
resistor of 1.5 KΩ and
GNT1# must have a PU
resistor of 1.5 KΩ.
Accuracy of internal PU/PD resistors: 80K to 250K.
Location of the GCB (General Configuration Block) cannot be determined by software. See the AMD Geode™ SC3200 Specification Update document.
58
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
3.3
Multiplexing Configuration
The tables that follow list multiplexing options and their
configurations. Certain multiplexing options may be chosen
per signal; others are available only for a group of signals.
Where ever a GPIO pin is multiplexed with another function, there is an optional pull-up resistor on this pin; after
system reset, the pull-up is present. This pull-up resistor
can be disabled by writing Core Logic registers. The configuration is without regard to the selected ball function.
The above applies to all pins multiplexed with GPIO,
except GPIO12, GPIO13, and GPIO16.
Table 3-7. Two-Signal/Group Multiplexing
Default
EBGA
TEPBGA
Signal
Ball No.
Alternate
Configuration
Signal
IDE
TFT, PCI, GPIO, System
A26
AD3
IDE_ADDR0
C26
AE1
IDE_ADDR1
TFTD2
C17
U2
IDE_ADDR2
TFTD4
B24
AC3
IDE_DATA0
TFTD6
A24
AC1
IDE_DATA1
TFTD16
D23
AC2
IDE_DATA2
TFTD14
C23
AB4
IDE_DATA3
TFTD12
B23
AB1
IDE_DATA4
FP_VDD_ON
A23
AA4
IDE_DATA5
CLK27M
C22
AA3
IDE_DATA6
IRQ9
B22
AA2
IDE_DATA7
INTD#
A21
Y3
IDE_DATA8
GPIO40
C20
Y2
IDE_DATA9
DDC_SDA
A20
Y1
IDE_DATA10
DDC_SCL
C19
W4
IDE_DATA11
GPIO41
B19
W3
IDE_DATA12
TFTD13
A19
V3
IDE_DATA13
TFTD15
C18
V2
IDE_DATA14
TFTD17
B18
V1
IDE_DATA15
TFTD7
C21
Y4
IDE_IOR0#
TFTD10
A25
AD1
IDE_IORDY0
TFTD11
C24
AC4
IDE_DREQ0
TFTD8
D24
AD2
IDE_IOW0#
TFTD9
A27
AF2
IDE_CS0#
TFTD5
C16
P2
IDE_CS1#
TFTDE
C25
AD4
IDE_DACK0#
TFTD0
A22
AA1
IDE_RST#
TFTDCK
D25
AF1
IRQ14
TFTD1
Ball No.
H1
D11
PMR[24] = 0
TFTD3
Sub-ISA
TRDE#
AMD Geode™ SC3200 Processor Data Book
PMR[12] = 0
Configuration
PMR[24] = 1
GPIO
GPIO0
PMR[12] = 1
59
Revision 5.1
Signal Definitions
Table 3-7. Two-Signal/Group Multiplexing (Continued)
Default
EBGA
TEPBGA
Signal
Configuration
Ball No.
N29
GPIO12
AL11
M29
GPIO13
AB2C
PMR[19] = 1
AB2D
GPIO
GPIO18
UART
PMR[16] = 0
Ball No.
DTR1#/BOUT1
Infrared
J3
C11
IRTX
J28
AK8
IRRX1
SOUT3
PMR[6] = 1
SIN3
GPIO
LPC
AJ11
M28
GPIO32
AL10
L31
GPIO33
AK10
L30
GPIO34
LAD2
AJ10
L29
GPIO35
LAD3
AL9
L28
GPIO36
LDRQ#
AK9
K31
GPIO37
LFRAME#
AJ9
K28
GPIO38/IRRX2
LPCPD#
AL8
J31
GPIO39
SERIRQ
PMR[14] = 0 and
PMR[22] = 0
Ball No.
E28
PMR[16] = 1
UART
PMR[6] = 0
Ball No.
AJ4
Configuration
ACCESS.bus
PMR[19] = 0
Ball No.
AG1
Signal
GPIO
AJ12
A28
Alternate
LAD0
PMR[14] = 1 and
PMR[22] = 1
LAD1
UART
SIN2
Internal Test
PMR[28] = 0
Ball No.
SDTEST3
AC97
FPCI Monitoring
AJ15
U29
AC97_RST#
FPCI_MON = 0
AK14
U31
SDATA_IN
F_GNT0#
AL14
U30
BIT_CLK
F_TRDY#
Ball No.
PMR[28] = 1
F_STOP#
Internal Test
FPCI_MON = 1
Internal Test
C28
AG4
PLL6B
PMR[29] = 0
TEST1
B29
AJ1
PLL5B
TEST2
D28
AH3
PLL2B
TEST0
PMR[29] = 1
Table 3-8. Three-Signal/Group Multiplexing
Default
EBGA
TEPBGA
Signal
Ball No.
60
Signal
F1
D9
IOR#
A8
IOW#
PMR[21] = 0 and
PMR[2] = 0
GPIO
Alternate2
Configuration
Signal
Sub-ISA1
Sub-ISA
G3
Ball No.
Configuration
Alternate1
DOCR#
DOCW#
GPIO
PMR[21] = 0 and
PMR[2] = 1
AC97
Configuration
GPIO14
GPIO15
PMR[21] = 1 and
PMR[2] = 1
FPCI Monitoring
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
Table 3-8. Three-Signal/Group Multiplexing (Continued)
Default
EBGA
TEPBGA
AL15
V31
Signal
Configuration
GPIO16
PMR[0] = 0 and
FPCI_MON = 0
Ball No.
H4
Signal
PC_BEEP
C9
GPIO19
PMR[9] = 0 and
PMR[4] = 0
INTC#
PMR[23] = 0 and
AFD#/DSTRB# (PMR[27] = 0 and
FPCI_MON = 0)
BUSY/WAIT#
Signal
F_DEVSEL
PMR[9] = 0 and
PMR[4] = 1
TFTDE
PMR[23] = 1 and
(PMR[27] = 0 and
FPCI_MON = 0)
IOCHRDY
B18
AB2
D22
T1
B17
AA3
D21
ERR#
TFTD4
F_C/BE0#
Y3
B21
INIT#
TFTD5
SMI_O
AA1
C21
PD0
TFTD6
F_AD0
Y1
A21
PD1
TFTD7
F_AD1
W3
D20
PD2
TFTD8
F_AD2
W2
C20
PD3
TFTD9
F_AD3
V1
C18
PD4
TFTD10
F_AD4
V2
C19
PD5
TFTD11
F_AD5
V3
A20
PD6
TFTD1
F_AD6
U1
A18
PD7
TFTD13
F_AD7
T3
D17
PE
TFTD14
F_C/BE2#
T4
C17
SLCT
TFTD15
F_C/BE3#
W1
B20
SLIN#
/ASTRB#
TFTD16
F_IRDY
AB1
A22
STB#/WRITE#
TFTD17
F_FRAME#
Ball No.
TFTD3
GPIO
PMR[9] = 1 and
PMR[4] = 1
FPCI Monitoring
FPCI_CLK
U3
TFTD2
Configuration
FPCI_MON = 1
Sub-ISA
TFT3
Parallel Port
ACK#
Configuration
PMR[0] = 1 = 0 and
FPCI_MON = 0
Alternate2
PCI2
GPIO
Ball No.
INTR_O
F_C/BE1#
PMR[23] = 0 and
(PMR[27] = 1 or
FPCI_MON = 1)
TFT3
Sub-ISA
J4
A10
GPIO17
PMR[23] = 0 and
PMR[5] = 0
IOCS0#
PMR[23] = 0 and
PMR[5] = 1
TFTDCK
PMR[23] = 1
H3
A9
GPIO20
PMR[23] = 0 and
PMR[7] = 0
DOCCS#
PMR[23] = 0 and
PMR[7] = 1
TFTD0
PMR[23] = 1
H2
D10
GPIO1
PMR[23] = 0 and
PMR[13] = 0
IOCS1#
PMR[23] = 0 and
PMR[13] = 1
TFTD12
PMR[23] = 1
Ball No.
AB1
GPIO
Sub-ISA
AJ13
N31
AB1C
PMR[23] = 0
GPIO20
PMR[23] = 1 and
PMR[7] = 0
DOCCS#
PMR[23] = 1 and
PMR[7] = 1
AL12
N30
AB1D
PMR[23] = 0
GPIO1
PMR[23] = 1 and
PMR[13] = 0
IOCS1#
PMR[23] = 1 and
PMR[13] = 1
Ball No.
H30
AJ8
GPIO
GPIO11
Ball No.
AL16
1.
2.
3.
Alternate1
V30
PMR[18] = 0 and
PMR[8] = 0
UART2
RI2#
Internal Test
GXCLK
PMR[23] = 0 and
PMR[29] = 0
PMR[18] = 1 and
PMR[8] = 0
IDE2
IRQ15
Internal Test
TEST3
PMR[23] = 0 and
PMR[29] = 1
PMR[18] = 0 and
PMR[8] = 1
TFT
FP_VDD_ON
PMR[23] = 1
The combination of PMR[21] = 1 and PMR[2] = 0 is undefined and should not be used.
The combination of PMR[9] = 1 and PMR[4] = 0 is undefined and should not be used.
These TFT outputs are reset to 0 by POR# if the TFT_PRSNT strap is pulled high or PMR[10] = 0. This relates to signals TFTD[17:0],
TFTDE, TFTDCK.
AMD Geode™ SC3200 Processor Data Book
61
Revision 5.1
Signal Definitions
TEPBGA
EBGA
Table 3-9. Four-Signal/Group Multiplexing
Default
Signal
Ball No.
AH4
C30 GPIO7
AJ2
C31 GPIO8
AH3
D28 GPIO6
AG4
C28 GPIO9
AJ1
B29 GPIO10
62
Configuration
Alternate1
Signal
GPIO
Configuration
Alternate2
Signal
UART2
RTS2#
PMR[17] = 1
and
PMR[8] = 0
PMR[17] = 0
and
PMR[8] = 0
CTS2#
PMR[18] = 0
and
PMR[8] = 0
DTR2#/BOUT2 PMR[18] = 1
and
PMR[8] = 0
DSR2#
DCD2#
Configuration
IDE2
IDE_DACK1#
IDE_DREQ1
IDE_IOR1#
IDE_IOW1#
IDE_IORDY1
Alternate3
Signal
Configuration
Internal Test
SDTEST0
PMR[17] = 0
and
PMR[8] = 1
SDTEST4
PMR[18] = 0
and
PMR[8] = 1
SDTEST2
SDTEST5
SDTEST1
PMR[17] = 1
and
PMR[8] = 1
PMR[18] = 1
and
PMR[8] = 1
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
3.4
Signal Descriptions
Information in the tables that follow may have duplicate information in multiple tables. Multiple references all contain identical information.
3.4.1
System Interface
Ball No.
Signal Name
EBGA
TEPBGA
Type
CLKSEL1
B27
AF3
I
CLKSEL0
F3
B8
Description
Fast-PCI Clock Selects. These strap signals
are used to set the internal Fast-PCI clock.
Mux
SOUT1
RD#
00 = 33.3 MHz
01 = 48 MHz
10 = 66.7 MHz
11 = 33.3 MHz
During system reset, an internal pull-down
resistor of 100 KΩ exists on these balls. An
external pull-up or pull-down resistor of 1.5
KΩ must be used.
CLKSEL3
AL13
P30
CLKSEL2
AK3
D29
I
Maximum Core Clock Multiplier. These
strap signals are used to set the maximum
allowed multiplier value for the core clock.
SYNC
SOUT2
During system reset, an internal pull-down
resistor of 100 KΩ exists on these balls. An
external pull-up or pull-down resistor of 1.5
KΩ must be used.
BOOT16
G4
C8
I
Boot ROM is 16 Bits Wide. This strap signal
enables the optional 16-bit wide Sub-ISA
bus.
ROMCS#
During system reset, an internal pull-down
resistor of 100 KΩ exists on these balls. An
external pull-up or pull-down resistor of 1.5
KΩ must be used.
LPC_ROM
E4
D6
I
LPC_ROM. This strap signal forces selecting
of the LPC bus and sets bit F0BAR1+I/O Offset 10h[15], LPC ROM Addressing Enable. It
enables the SC3200 to boot from a ROM
connected to the LPC bus.
PCICLK1
During system reset, an internal pull-down
resistor of 100 KΩ exists on these balls. An
external pull-up or pull-down resistor of 1.5
KΩ must be used.
TFT_PRSNT
AK13
P29
I
TFT Present. A strap used to select multiplexing of TFT signals at power-up. Enables
using TFT instead of Parallel Port, ACB1,
and GPIO17.
SDATA_OUT
During system reset, an internal pull-down
resistor of 100 KΩ exists on these balls. An
external pull-up or pull-down resistor of 1.5
KΩ must be used.
AMD Geode™ SC3200 Processor Data Book
63
Revision 5.1
3.4.1
Signal Definitions
System Interface (Continued)
Ball No.
Signal Name
EBGA
TEPBGA
Type
Description
Mux
FPCI_MON
D3
A4
I
Fast-PCI Monitoring. The strap on this ball
forces selection of Fast-PCI monitoring signals. For normal operation, strap this signal
low using a 1.5 KΩ resistor. The value of this
strap can be read on the MCR[30].
PCICLK0
DID1
D2
C6
I
GNT1#
DID0
D4
C5
I
Device ID. Together, the straps on these signals define the system-level chip ID.
GNT0#
The value of DID1 can be read in the
MCR[29]. The value of DID0 can be read in
the MCR[31].
DID0 and DID1 must have a pull-up resistor
of 1.5 KΩ.
POR#
J29
AH9
I
Power On Reset. POR# is the system reset
signal generated from the power supply to
indicate that the system should be reset.
---
X32I
C30
AJ2
I/O
---
X32O
D29
AJ3
Crystal Connections. Connected directly to
a 32.768 KHz crystal. This clock input is
required even if the internal RTC is not being
used. Some of the internal clocks are derived
from this clock. If an external clock is used, it
should be connected to X32I, using a voltage
level of 0 volts to VCORE +10% maximum.
X32O should remain unconnected.
X27I
A29
AG3
X27O
D27
AH2
CLK27M
A23
AA4
O
27 MHz Output Clock. Output of crystal
oscillator.
PCIRST#
D1
A6
O
PCI and System Reset. PCIRST# is the
reset signal for the PCI bus and system. It is
asserted for approximately 100 µs after
POR# is negated.
64
I/O
Crystal Connections. Connected directly to
a 27.000 MHz crystal. Some of the internal
clocks are derived from this clock. If an external clock is used, it should be connected to
X27I, using a voltage level of 0 volts to VIO
and X27O should be remain unconnected.
---
-----
IDE_DATA5
---
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
3.4.2
Memory Interface Signals
Ball No.
Signal Name
EBGA
TEPBGA
Type
MD[63:0]
See
Table 3-3
on page
38.
See
Table 3-5
on page
54.
I/O
Memory Data Bus. The data bus lines
driven to/from system memory.
---
MA[12:0]
See
Table 3-3
on page
38.
See
Table 3-5
on page
54.
O
Memory Address Bus. The multiplexed row/
column address lines driven to the system
memory. Supports 256-Mbit SDRAM.
---
BA1
P31
AK14
O
P30
AJ13
Bank Address Bits. These bits are used to
select the component bank within the
SDRAM.
---
BA0
CS1#
AK29
AH27
---
CS0#
P29
AL12
Chip Selects. These bits are used to select
the module bank within system memory.
Each chip select corresponds to a specific
module bank. If CS# is high, the bank(s) do
not respond to RAS#, CAS#, and WE# until
the bank is selected again.
RASA#
N31
AK12
O
Row Address Strobe. RAS#, CAS#, WE#
and CKE are encoded to support the different
SDRAM commands. RASA# is used with
CS[1:0]#.
---
CASA#
N30
AJ12
O
Column Address Strobe. RAS#, CAS#,
WE# and CKE are encoded to support the
different SDRAM commands. CASA# is used
with CS[1:0]#.
---
WEA#
N29
AH12
O
Write Enable. RAS#, CAS#, WE# and CKE
are encoded to support the different SDRAM
commands. WEA# is used with CS[1:0]#.
---
DQM7
AJ20
AB31
O
---
DQM6
AJ26
AG29
DQM5
AC30
AK21
DQM4
T28
AL15
Data Mask Control Bits. During memory
read cycles, these outputs control whether
SDRAM output buffers are driven on the MD
bus or not. All DQM signals are asserted during read cycles.
DQM3
AJ21
AC31
DQM2
AL26
AG30
DQM1
AF31
AH23
DQM0
M31
AL11
CKEA
AC28
AL22
O
Description
During memory write cycles, these outputs
control whether or not MD data is written into
SDRAM.
DQM[7:0] connect directly to the [DQM7:0]
pins of each DIMM connector.
O
Clock Enable. These signals are used to
enter Suspend/power-down mode. CKEA is
used with CS[1:0]#.
Mux
---
---
-----------------
If CKE goes low when no read or write cycle
is in progress, the SDRAM enters powerdown mode. To ensure that SDRAM data
remains valid, the self-refresh command is
executed. To exit this mode, and return to
normal operation, drive CKE high.
These signals should have an external pulldown resistor of 33 KΩ.
AMD Geode™ SC3200 Processor Data Book
65
Revision 5.1
3.4.2
Signal Definitions
Memory Interface Signals (Continued)
Ball No.
Signal Name
EBGA
TEPBGA
Type
SDCLK3
AJ16
V29
O
SDCLK2
AL20
AA28
SDCLK1
AH16
W29
SDCLK0
AC29
AJ21
SDCLK_IN
AJ30
AJ27
SDCLK_OUT
AH28
AK28
3.4.3
Description
Mux
SDRAM Clocks. SDRAM uses these clocks
to sample all control, address, and data lines.
To ensure that the Suspend mode functions
correctly, SDCLK3 and SDCLK1 should be
used with CS1#. SDCLK2 and SDCLK0
should be used together with CS0#.
---
I
SDRAM Clock Input. The SC3200 samples
the memory read data on this clock. Works in
conjunction with the SDCLK_OUT signal.
---
O
SDRAM Clock Output. This output is routed
back to SDCLK_IN. The board designer
should vary the length of the board trace to
control skew between SDCLK_IN and
SDCLK.
---
-------
Video Port Interface Signals
Ball No.
Mux
Signal Name
EBGA
TEPBGA
Type
VPD7
AJ6
G31
I
VPD6
AJ7
H28
VPD5
AL6
H29
---
VPD4
AH8
H30
---
VPD3
AL7
H31
---
VPD2
AJ8
J28
---
VPD1
AK8
J29
---
VPD0
AH9
J30
---
VPCKIN
AH7
F31
66
I
Description
Video Port Data. The data is input from the
CCIR-656 video decoder.
Video Port Clock Input. The clock input
from the video decoder.
-----
---
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
3.4.4
TFT Interface Signals
Ball No.
Mux
Signal Name
EBGA
TEPBGA
Type
HSYNC
J1
A11
O
Horizontal Sync
---
VSYNC
J2
B11
O
Vertical Sync
---
TFTDCK
A22
AA1
O
TFT Clock.
J4
A10
C16
P2
U3
B18
B23
AB1
AL16
V30
See
Table 3-3
on page
38.
See
Table 3-5
on page
54.
TFTDE
FP_VDD_ON
TFTD[17:0]
3.4.5
Description
IDE_RST#
GPIO17+ IOCS0#
O
TFT Data Enable.
IDE_CS1#
ACK#+FPCICLK
O
O
TFT Power Control. Used to enable power
to the flat panel display, with power
sequence timing.
IDE_DATA4
GXCLK+TEST3
Digital RGB Data to TFT.
The TFT interface is
TFTD[5:0] - Connect to the BLUE TFT inputs. muxed with the IDE
TFTD[11:6] - Connect to GREEN TFT inputs. interface or the ParTFTD[17:12] - Connect to RED TFT inputs.
allel Port. See Table
3-7 on page 59 and
Table 3-8 on page
60 for details.
ACCESS.bus Interface Signals
Ball No.
Type
Signal Name
EBGA
TEPBGA
AB1C
AJ13
N31
Description
I/O
ACCESS.bus 1 Serial Clock. This is the
serial clock for the interface.
Note:
AB1D
AL12
N30
I/O
AB2C
AJ12
N29
I/O
AB2D
AL11
M29
I/O
AMD Geode™ SC3200 Processor Data Book
GPIO12
If AB2C function is selected but not
used, tie AB2C high.
ACCESS.bus 2 Serial Data. This is the bidirectional serial data signal for the interface.
Note:
GPIO1+IOCS1#
If AB1D function is selected but not
used, tie AB1D high.
ACCESS.bus 2 Serial Clock. This is the
serial clock for the interface.
Note:
GPIO20+DOCCS#
If selected as AB1C function but not
used, tie AB1C high.
ACCESS.bus 1 Serial Data. This is the bidirectional serial data signal for the interface.
Note:
Mux
GPIO13
If AB2D function is selected but not
used, tie AB2D high.
67
Revision 5.1
3.4.6
Signal Definitions
PCI Bus Interface Signals
BalL No.
Signal Name
EBGA
TEPBGA
Type
PCICLK
E2
A7
I
PCI Clock. PCICLK provides timing for all
transactions on the PCI bus. All other PCI
signals are sampled on the rising edge of
PCICLK, and all timing parameters are
defined with respect to this edge.
PCICLK0
D3
A4
O
FPCI_MON (Strap)
PCICLK1
E4
D6
O
PCI Clock Outputs. PCICLK0 and PCICLK1
provide clock drives for the system at 33
MHz. These clocks are asynchronous to PCI
signals. There is low skew between all outputs. One of these clock signals should be
connected to the PCICLK input. All PCI clock
users in the system (including PCICLK)
should receive the clock with as low a skew
as possible.
AD[31:24]
See
Table 3-5
on page
54.
I/O
Multiplexed Address and Data. A bus
transaction consists of an address phase in
the cycle in which FRAME# is asserted followed by one or more data phases. During
the address phase, AD[31:0] contain a physical 32-bit address. For I/O, this is a byte
address. For configuration and memory, it is
a DWORD address. During data phases,
AD[7:0] contain the least significant byte
(LSB) and AD[31:24] contain the most significant byte (MSB).
D[7:0]
AD[23:0]
See
Table 3-3
on page
38.
C/BE3#
A8
H4
I/O
C/BE2#
D8
F3
C/BE1#
A10
J2
C/BE0#
A13
L1
INTA#
AE3
D26
INTB#
AF1
C26
INTC#
H4
C9
INTD#
B22
AA2
I
Description
Multiplexed Command and Byte Enables.
During the address phase of a transaction
when FRAME# is active, C/BE[3:0]# define
the bus command. During the data phase, C/
BE[3:0]# are used as byte enables. The byte
enables are valid for the entire data phase
and determine which byte lanes carry meaningful data. C/BE0# applies to byte 0 (LSB)
and C/BE3# applies to byte 3 (MSB).
PCI Interrupts. The SC3200 provides inputs
for the optional “level-sensitive” PCI interrupts (also known in industry terms as
PIRQx#). These interrupts can be mapped to
IRQs of the internal 8259A interrupt controllers using PCI Interrupt Steering Registers 1
and 2 (F0 Index 5Ch and 5Dh).
Note:
68
Mux
---
LPC_ROM (Strap)
A[23:0]
D11
D10
D9
D8
----GPIO19+IOCHRDY
IDE_DATA7
If selected as INTC# or INTD# function(s) but not used, tie INTC# and
INTD# high.
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
3.4.6
PCI Bus Interface Signals (Continued)
BalL No.
Signal Name
PAR
EBGA
TEPBGA
Type
C10
J4
I/O
Description
Mux
Parity. Parity generation is required by all
PCI agents. The master drives PAR for
address- and write-data phases. The target
drives PAR for read-data phases. Parity is
even across AD[31:0] and C/BE[3:0]#.
D12
For address phases, PAR is stable and valid
one PCI clock after the address phase. It has
the same timing as AD[31:0] but is delayed
by one PCI clock.
For data phases, PAR is stable and valid one
PCI clock after either IRDY# is asserted on a
write transaction or after TRDY# is asserted
on a read transaction.
Once PAR is valid, it remains valid until one
PCI clock after the completion of the data
phase. (Also see PERR#.)
FRAME#
E1
D8
I/O
Frame Cycle. Frame is driven by the current
master to indicate the beginning and duration
of an access. FRAME# is asserted to indicate the beginning of a bus transaction.
While FRAME# is asserted, data transfers
continue. FRAME# is de-asserted when the
transaction is in the final data phase.
---
This signal is internally connected to a pullup resistor.
IRDY#
C8
F2
I/O
Initiator Ready. IRDY# is asserted to indicate that the bus master is able to complete
the current data phase of the transaction.
IRDY# is used in conjunction with TRDY#. A
data phase is completed on any PCI clock in
which both IRDY# and TRDY# are sampled
as asserted. During a write, IRDY# indicates
that valid data is present on AD[31:0]. During
a read, it indicates that the master is prepared to accept data. Wait cycles are
inserted until both IRDY# and TRDY# are
asserted together.
D14
This signal is internally connected to a pullup resistor.
AMD Geode™ SC3200 Processor Data Book
69
Revision 5.1
3.4.6
Signal Definitions
PCI Bus Interface Signals (Continued)
BalL No.
Signal Name
TRDY#
EBGA
TEPBGA
Type
B8
F1
I/O
Description
Mux
Target Ready. TRDY# is asserted to indicate that the target agent is able to complete
the current data phase of the transaction.
TRDY# is used in conjunction with IRDY#. A
data phase is complete on any PCI clock in
which both TRDY# and IRDY# are sampled
as asserted. During a read, TRDY# indicates
that valid data is present on AD[31:0]. During
a write, it indicates that the target is prepared
to accept data. Wait cycles are inserted until
both IRDY# and TRDY# are asserted
together.
D13
This signal is internally connected to a pullup resistor.
STOP#
D9
G1
I/O
Target Stop. STOP# is asserted to indicate
that the current target is requesting that the
master stop the current transaction. This signal is used with DEVSEL# to indicate retry,
disconnect, or target abort. If STOP# is sampled active by the master, FRAME# is deasserted and the cycle is stopped within
three PCI clock cycles. As an input, STOP#
can be asserted in the following cases:
1)
If a PCI master tries to access memory
that has been locked by another master.
This condition is detected if FRAME#
and LOCK# are asserted during an
address phase.
2)
If the PCI write buffers are full or if a previously buffered cycle has not completed.
3)
On read cycles that cross cache line
boundaries. This is conditional based
upon the programming of GX1 module’s
PCI Configuration Register, Index
41h[1].
D15
This signal is internally connected to a pullup resistor.
70
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
3.4.6
PCI Bus Interface Signals (Continued)
BalL No.
Signal Name
LOCK#
EBGA
TEPBGA
Type
C9
H3
I/O
Description
Lock Operation. LOCK# indicates an atomic
operation that may require multiple transactions to complete. When LOCK# is asserted,
non-exclusive transactions may proceed to
an address that is not currently locked (at
least 16 bytes must be locked). A grant to
start a transaction on PCI does not guarantee control of LOCK#. Control of LOCK# is
obtained under its own protocol in conjunction with GNT#.
Mux
---
It is possible for different agents to use PCI
while a single master retains ownership of
LOCK#. The arbiter can implement a complete system lock. In this mode, if LOCK# is
active, no other master can gain access to
the system until the LOCK# is de-asserted.
This signal is internally connected to a pullup resistor.
DEVSEL#
B5
E4
I/O
Device Select. DEVSEL# indicates that the
driving device has decoded its address as
the target of the current access. As an input,
DEVSEL# indicates whether any device on
the bus has been selected. DEVSEL# is also
driven by any agent that has the ability to
accept cycles on a subtractive decode basis.
As a master, if no DEVSEL# is detected
within and up to the subtractive decode
clock, a master abort cycle is initiated (except
for special cycles which do not expect a
DEVSEL# returned).
BHE#
This signal is internally connected to a pullup resistor.
PERR#
B9
H2
I/O
Parity Error. PERR# is used for reporting
data parity errors during all PCI transactions
except a Special Cycle. The PERR# line is
driven two PCI clocks after the data in which
the error was detected. This is one PCI clock
after the PAR that is attached to the data.
The minimum duration of PERR# is one PCI
clock for each data phase in which a data
parity error is detected. PERR# must be
driven high for one PCI clock before being
placed in TRI-STATE. A target asserts
PERR# on write cycles if it has claimed the
cycle with DEVSEL#. The master asserts
PERR# on read cycles.
---
This signal is internally connected to a pullup resistor.
AMD Geode™ SC3200 Processor Data Book
71
Revision 5.1
3.4.6
Signal Definitions
PCI Bus Interface Signals (Continued)
BalL No.
Signal Name
SERR#
EBGA
TEPBGA
Type
A9
H1
I/O
Description
Mux
System Error. SERR# can be asserted by
any agent for reporting errors other than PCI
parity. When the PFS bit is enabled in the
GX1 module’s PCI Control Function 2 register (Index 41h[5]), SERR# is asserted upon
assertion of PERR#.
---
This signal is internally connected to a pullup resistor.
REQ1#
E3
A5
REQ0#
C1
B5
I
Request Lines. REQ[1:0]# indicate to the
arbiter that an agent requires the bus. Each
master has its own REQ# line. REQ# priorities (in order) are:
1)
VIP
2)
IDE Channel 0
3)
IDE Channel 1
4)
Audio
5)
USB
6)
External REQ0#
7)
External REQ1#.
-----
Each REQ# is internally connected to a pullup resistor.
GNT1#
D2
C6
GNT0#
D4
C5
O
Grant Lines. GNT[1:0]# indicate to the
requesting master that it has been granted
access to the bus. Each master has its own
GNT# line. GNT# can be retracted at any
time a higher REQ# is received or if the master does not begin a cycle within a minimum
period of time (16 PCI clocks).
DID1 (Strap)
DID0 (Strap)
Each of these signals is internally connected
to a pull-up resistor.
GNT0# must have a pull-up resistor of 1.5
KΩ and GNT1# must have a pull-up resistor
of 1.5 KΩ.
72
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
3.4.7
Sub-ISA Interface Signals
Ball No.
Signal Name
EBGA
TEPBGA
Type
A[23:0]
See
Table 3-3
on page
38.
See
Table 3-5
on page
54.
O
Address Lines
D15
See
Table 3-3
on page
38.
See
Table 3-5
on page
54.
I/O
Data Bus
D14
D13
Description
Mux
AD[23:0]
STOP#
IRDY#
TRDY#
D12
PAR
D11
C/BE3#
D10
C/BE2#
D9
C/BE1#
D8
C/BE0#
D[7:0]
AD[31:24]
BHE#
B5
E4
O
Byte High Enable. With A0, defines byte
accessed for 16 bit wide bus cycles.
IOCS1#
H2
D10
O
I/O Chip Selects
AL12
N30
AB1D+GPIO1
IOCS0#
J4
A10
GPIO17+TFTDCK
ROMCS#
G4
C30
O
ROM or Flash ROM Chip Select
BOOT16 (Strap)
DOCCS#
H3
A9
O
DiskOnChip or NAND Flash Chip Select
GPIO20+TFTD0
AJ13
N31
H1
D11
TRDE#
DEVSEL#
GPIO1+TFTD12
AB1C+GPIO20
O
Transceiver Data Enable Control. Active
low for Sub-ISA data transfers. The signal
timing is as follows:
GPIO0
• In a read cycle, TRDE# has the same
timing as RD#.
• In a write cycle, TRDE# is asserted (to
active low) at the time WR# is asserted. It
continues being asserted for one PCI
clock cycle after WR# has been negated,
then it is negated.
RD#
F3
B8
O
Memory or I/O Read. Active on any read
cycle.
CLKSEL0 (Strap)
WR#
G1
B9
O
Memory or I/O Write. Active on any write
cycle.
---
IOR#
F1
D9
O
I/O Read. Active on any I/O read cycle.
DOCR#+GPIO14
IOW#
G3
A8
O
I/O Write. Active on any I/O write cycle.
DOCW#+GPIO15
DOCR#
F1
D9
O
DiskOnChip or NAND Flash Read. Active
on any memory read cycle to DiskOnChip.
IOR#+GPIO14
DOCW#
G3
A8
O
DiskOnChip or NAND Flash Write. Active
on any memory write cycle to DiskOnChip.
IOW#+GPIO15
AMD Geode™ SC3200 Processor Data Book
73
Revision 5.1
3.4.7
Signal Definitions
Sub-ISA Interface Signals (Continued)
Ball No.
Signal Name
IRQ9
EBGA
TEPBGA
Type
C22
AA3
I
Description
Interrupt 9 Request Input. Active high.
Note:
IOCHRDY
H4
C9
I
IDE_DATA6
If IRQ9 function is selected but not
used, tie IRQ9 low.
I/O Channel Ready
Note:
3.4.8
Mux
GPIO19+INTC#
If IOCHRDY function is selected but
not used, tie IOCHRDY high.
Low Pin Count (LPC) Bus Interface Signals
Ball No.
Signal Name
EBGA
TEPBGA
Type
LAD3
AJ10
L29
I/O
LAD2
AK10
L30
LAD1
AL10
L31
GPIO33
LAD0
AJ11
M28
GPIO32
LDRQ#
AL9
L28
I
Description
Mux
LPC Address-Data. Multiplexed command,
address, bidirectional data, and cycle status.
LPC DMA Request. Encoded DMA request
for LPC interface.
Note:
AK9
K31
O
LPC Frame. A low pulse indicates the beginning of a new LPC cycle or termination of a
broken cycle.
LPCPD#
AJ9
K28
O
LPC Power-Down. Signals the LPC device
to prepare for power shut-down on the LPC
interface.
SERIRQ
AL8
J31
I/O
Serial IRQ. The interrupt requests are serialized over a single signal, where each IRQ
level is delivered during a designated time
slot.
74
GPIO34
GPIO36
If LDRQ# function is selected but not
used, tie LDRQ# high.
LFRAME#
Note:
GPIO35
GPIO37
GPIO38/IRRX2
GPIO39
If SERIRQ function is selected but
not used, tie SERIRQ high.
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
3.4.9
IDE Interface Signals
Ball No.
Signal Name
EBGA
TEPBGA
Type
IDE_RST#
A22
AA1
O
IDE Reset. This signal resets all the devices
that are attached to the IDE interface.
IDE_ADDR2
C17
U2
O
IDE_ADDR1
C26
AE1
IDE Address Bits. These address bits are
used to access a register or data port in a
device on the IDE bus.
IDE_ADDR0
A26
AD3
See
Table 3-3
on page
38.
See
Table 3-5
on page
54.
I/O
IDE Data Lines. IDE_DATA[15:0] transfers
data to/from the IDE devices.
The IDE interface is
muxed with the TFT
interface. See Table
3-7 on page 59 for
details.
IDE_IOR0#
C21
Y4
O
TFTD10
IDE_IOR1#
AH3
D28
O
IDE I/O Read Channels 0 and 1.
IDE_IOR0# is the read signal for Channel 0
and IDE_IOR1# is the read signal for Channel 1. Each signal is asserted at read
accesses to the corresponding IDE port
addresses.
IDE_IOW0#
D24
AD2
O
IDE_IOW1#
AG4
C28
O
IDE_CS0#
A27
AF2
O
IDE_CS1#
C16
P2
O
IDE_IORDY0
A25
AD1
I
IDE_IORDY1
AJ1
B29
I
IDE_DATA[15:0]
Description
TFTDCK
TFTD4
TFTD2
TFTD3
IDE I/O Write Channels 0 and 1.
IDE_IOW0# is the write signal for Channel 0.
IDE_IOW1# is the write signal for Channel 1.
Each signal is asserted at write accesses to
corresponding IDE port addresses.
IDE Chip Selects 0 and 1. These signals are
used to select the command block registers
in an IDE device.
I/O Ready Channels 0 and 1. When deasserted, these signals extend the transfer
cycle of any host register access if the
required device is not ready to respond to the
data transfer request.
Note:
IDE_DREQ0
C24
AC4
I
IDE_DREQ1
AJ2
C31
I
IDE_DACK0#
C25
AD4
O
IDE_DACK1#
AH4
C30
O
GPIO6+DTR2#/
BOUT2+SDTEST5#
TFTD9
GPIO9+DCD2#+
SDTEST2
TFTD5
TFTDE
TFTD11
GPIO10+DSR2#+
SDTEST1
If selected as IDE_IORDY0 or
IDE_IORDY1 function(s) but not
used, then signal(s) should be tied
high.
DMA Request Channels 0 and 1. The
IDE_DREQ signals are used to request a
DMA transfer from the SC3200. The direction
of transfer is determined by the IDE_IOR/
IOW signals.
Note:
AMD Geode™ SC3200 Processor Data Book
Mux
TFTD8
GPIO8+CTS2#
+SDTEST5
If
selected
as
IDE_DREQ0/
IDE_DREQ1 function but not used,
tie IDE_DREQ0/IDE_DREQ1 low.
DMA Acknowledge Channels 0 and 1. The
IDE_DACK# signals acknowledge the DREQ
request to initiate DMA transfers.
TFTD0
GPIO7+RTS2#
+SDTEST0
75
Revision 5.1
3.4.9
Signal Definitions
IDE Interface Signals (Continued)
Ball No.
Signal Name
EBGA
TEPBGA
Type
IRQ14
D25
AF1
I
IRQ15
H30
AJ8
I
Description
Interrupt Request Channels 0 and 1.
These input signals are edge-sensitive interrupts that indicate when the IDE device is
requesting a CPU interrupt service.
Note:
3.4.10
Mux
TFTD1
GPIO11+RI2#
If selected as IRQ14/IRQ15 function
but not used, tie IRQ14/IRQ15 low.
Universal Serial Bus (USB) Interface Signals
Ball No.
Signal Name
EBGA
TEPBGA
Type
POWER_EN
B28
AH1
O
Power Enable. This signal enables the
power to a self-powered USB hub.
---
OVER_CUR#
C27
AF4
I
Overcurrent. This signal indicates that the
USB hub has detected an overcurrent on the
USB.
---
DPOS_PORT1
AH2
A28
I/O
USB Port 1 Data Positive for Port 1.1
---
DNEG_PORT1
AG3
A29
I/O
USB Port 1 Data Negative for port 1.1
---
DPOS_PORT2
AH1
B27
I/O
USB Port 2 Data Positive for Port 2.1
---
DNEG_PORT2
AG2
B28
I/O
USB Port 2 Data Negative for Port 2.1
---
DPOS_PORT3
AE4
A26
I/O
USB Port 3 Data Positive for Port 3.1
---
DNEG_PORT3
AF3
A27
I/O
USB Port 3 Data Negative for Port 3.1
---
1.
Description
Mux
A 15K ohm pull-down resistor is required on all ports (even if unused).
3.4.11
Serial Ports (UARTs) Interface Signals
Ball No.
Signal Name
EBGA
TEPBGA
Type
SIN1
D26
AG2
I
SIN2
AJ4
E28
SIN3
J28
AK8
Description
Serial Inputs. Receive composite serial data
from the communications link (peripheral
device, modem or other data transfer
device).
Note:
SOUT1
B27
AF3
SOUT2
AK3
D29
SOUT3
J3
C11
76
O
Mux
--SDTEST3
IRRX1
If selected as SIN2 or SIN3 function(s) but not used, then signal(s)
should be tied high.
Serial Outputs. Send composite serial data
to the communications link (peripheral
device, modem or other data transfer
device). These signals are set active high
after a system reset.
CLKSEL1 (Strap)
CLKSEL2 (Strap)
IRTX
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
3.4.11
Serial Ports (UARTs) Interface Signals (Continued)
Ball No.
Signal Name
EBGA
TEPBGA
Type
Description
RTS2#
AH4
C30
O
Request to Send. When low, indicates to the
modem or other data transfer device that the
corresponding UART is ready to exchange
data. A system reset sets these signals to
inactive high, and loopback operation holds
them inactive.
GPIO7+
IDE_DACK1#
CTS2#
AJ2
C31
I
Clear to Send. When low, indicates that the
modem or other data transfer device is ready
to exchange data.
GPIO8+
IDE_DREQ1
Note:
DTR1#/BOUT1
A28
AG1
DTR2#/BOUT2
AH3
D28
O
Mux
If selected as CTS2# function but not
used, tie CTS2# low.
Data Terminal Ready Outputs. When low,
indicate to the modem or other data transfer
device that the UART is ready to establish a
communications link. After a system reset,
these balls provide the DTR# function and
set these signals to inactive high. Loopback
operation drive them inactive.
GPIO18
GPIO6+IDE_IOR1#
Baud Outputs. Provide the associated serial
channel baud rate generator output signal if
test mode is selected (i.e., bit 7 of the EXCR1
Register is set).
RI2#
H30
AJ8
I
Ring Indicator. When low, indicates to the
modem that a telephone ring signal has been
received by the modem. They are monitored
during power-off for wakeup event detection.
Note:
DCD2#
AG4
C28
I
DSR2#
AJ1
B29
I
GPIO9+IDE_IOW1#
+SDTEST2
If selected as DCD2# function but
not used, tie DCD2# high.
Data Set Ready. When low, indicates that
the data transfer device (e.g., modem) is
ready to establish a communications link.
Note:
AMD Geode™ SC3200 Processor Data Book
If selected as RI2# function but not
used, tie RI2# high.
Data Carrier Detected. When low, indicates
that the data transfer device (e.g., modem) is
ready to establish a communications link.
Note:
GPIO11+IRQ15
GPIO10+
IDE_IORDY1
If selected as DSR2# function but
not used, tie DSR2# low.
77
Revision 5.1
3.4.12
Signal Definitions
Parallel Port Interface Signals
Ball No.
Signal Name
ACK#
AFD#/DSTRB#
EBGA
TEPBGA
Type
Description
Mux
U3
B18
I
Acknowledge. Pulsed low by the printer to
indicate that it has received data from the Parallel Port.
TFTDE+FPCICLK
AB2
D22
O
Automatic Feed. When low, instructs the
printer to automatically feed a line after printing each line. This signal is in TRI-STATE
after a 0 is loaded into the corresponding
control register bit. An external 4.7 KΩ pullup resistor should be attached to this ball.
TFTD2+INTR_O
Data Strobe (EPP). Active low, used in EPP
mode to denote a data cycle. When the cycle
is aborted, DSTRB# becomes inactive (high).
BUSY/WAIT#
T1
B17
I
Busy. Set high by the printer when it cannot
accept another character.
TFTD3+F_C/BE1#
Wait. In EPP mode, the Parallel Port device
uses this active low signal to extend its
access cycle.
ERR#
AA3
D21
I
Error. Set active low by the printer when it
detects an error.
INIT#
Y3
B21
O
Initialize. When low, initializes the printer.
This signal is in TRI-STATE after a 1 is
loaded into the corresponding control register
bit. Use an external 4.7 KΩ pull-up resistor.
TFTD5+SMI_O
PD7
U1
A18
I/O
TFTD13+F_AD7
PD6
V3
A20
PD5
V2
C19
Parallel Port Data. Transfer data to and from
the peripheral data bus and the appropriate
Parallel Port data register. These signals
have a high current drive capability.
PD4
V1
C18
TFTD10+F_AD4
PD3
W2
C20
TFTD9+F_AD3
PD2
W3
D20
TFTD8+F_AD2
PD1
Y1
A21
TFTD7+F_AD1
PD0
AA1
C21
T3
D17
PE
TFTD4+F_C/BE0#
TFTD1+F_AD6
TFTD11+F_AD5
TFTD6+F_AD0
I
Paper End. Set high by the printer when it is
out of paper.
TFTD14+F_C/BE2#
This ball has an internal weak pull-up or pulldown resistor that is programmed by software.
SLCT
T4
C17
I
Select. Set active high by the printer when
the printer is selected.
SLIN#/ASTRB#
W1
B20
O
Select Input. When low, selects the printer.
This signal is in TRI-STATE after a 0 is
loaded into the corresponding control register
bit. Uses an external 4.7 KΩ pull-up resistor.
TFTD15+F_C/BE3#
TFTD16+
F_IRDY#
Address Strobe (EPP). Active low, used in
EPP mode to denote an address or data
cycle. When the cycle is aborted, ASTRB#
becomes inactive (high).
78
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
3.4.12
Parallel Port Interface Signals (Continued)
Ball No.
Signal Name
EBGA
TEPBGA
Type
STB#/WRITE#
AB1
A22
O
Description
Data Strobe. When low, indicates to the
printer that valid data is available at the
printer port. This signal is in TRI-STATE after
a 0 is loaded into the corresponding control
register bit. An external 4.7 KΩ pull-up resistor should be employed.
Mux
TFTD17+
F_FRAME#
Write Strobe. Active low, used in EPP mode
to denote an address or data cycle. When
the cycle is aborted, WRITE# becomes inactive (high).
3.4.13
Fast Infrared (IR) Port Interface Signals
Ball No.
Signal Name
IRRX1
EBGA
TEPBGA
Type
J28
AK8
I
Description
Mux
IR Receive. Primary input to receive serial
data from the IR transceiver. Monitored during power-off for wakeup event detection.
SIN3
Note:
IRRX2/GPIO38
IRTX
If selected as IRRX1 function but not
used, tie IRRX1 high.
AJ9
K28
I
IR Receive 2. Auxiliary IR receiver input to
support a second transceiver. This input signal can be used when GPIO38 is selected
using PMR[14], and when AUX_IRRX bit in
register IRCR2 of the IR module in internal
SuperI/O is set.
LPCPD#
J3
C11
O
IR Transmit. IR serial output data.
SOUT3
AMD Geode™ SC3200 Processor Data Book
79
Revision 5.1
3.4.14
Signal Definitions
AC97 Audio Interface Signals
Ball No.
Signal Name
EBGA
TEPBGA
Type
BIT_CLK
AL14
U30
I
Description
Mux
Audio Bit Clock. The serial bit clock from
the codec.
Note:
If selected as BIT_CLK function but
not used, tie BIT_CLK low.
SDATA_OUT
AK13
P29
O
Serial Data Output. This output transmits
audio serial data to the codec.
SDATA_IN
AK14
U31
I
Serial Data Input. This input receives serial
data from the primary codec.
Note:
F_TRDY#
TFT_PRSNT (Strap)
F_GNT0#
If selected as SDATA_IN function
but not used, tie SDATA_IN low.
SDATA_IN2
H31
AL8
I
Serial Data Input 2. This input receives
serial data from the secondary codec. This
signal has wakeup capability.
---
SYNC
AL13
P30
O
Serial Bus Synchronization. This bit is
asserted to synchronize the transfer of data
between the SC3200 and the AC97 codec.
CLKSEL3 (Strap)
AC97_CLK
AJ14
P31
O
Codec Clock. It is twice the frequency of the
Audio Bit Clock.
---
AC97_RST#
AJ15
U29
O
Codec Reset. S3 to S5 wakeup is not supported because AC97_RST# is powered by
VIO. If wakeup from states S3 to S5 are
needed, a circuit in the system board should
be used to reset the AC97 codec.
F_STOP#
PC_BEEP
AL15
V31
O
PC Beep. Legacy PC/AT speaker output.
3.4.15
GPIO16+
F_DEVSEL#
Power Management Interface Signals
Ball No.
Signal Name
EBGA
TEPBGA
Type
CLK32
H29
AH8
O
32.768 KHz Output Clock
---
GPWIO0
E31
AH6
I/O
---
GPWIO1
G28
AK5
General Purpose Wakeup I/Os. These signals each have an internal pull-up of 100 KΩ.
GPWIO2
G29
AJ6
LED#
D31
AL4
O
LED Control. Drives an externally connected
LED (on, off or a 1 Hz blink). Sleeping /
Working indicator. This signal is an opendrain output.
---
ONCTL#
E30
AJ5
O
On / Off Control. This signal indicates to the
main power supply that power should be
turned on. This signal is an open-drain output.
---
80
Description
Mux
-----
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
3.4.15
Power Management Interface Signals (Continued)
Ball No.
Signal Name
PWRBTN#
EBGA
TEPBGA
Type
E29
AH5
I
Description
Power Button. Input used by the power
management logic to monitor external system events, most typically a system on/off
button or switch.
Mux
---
The signal has an internal pull-up of 100 KΩ,
a Schmitt-trigger input buffer and debounce
protection of at least 16 ms.
ACPI is non-functional and all ACPI outputs
are undefined when the power-up sequence
does not include using the power button.
SUSP# is an internal signal generated from
the ACPI block. Without an ACPI reset,
SUSP# can be permanently asserted. If the
USE_SUSP bit in CCR2 of GX1 module is
enabled (Index C2h[7] = 1), the CPU will
stop.
If ACPI functionality is desired, or the situation described above avoided, the power button must be toggled. This can be done
externally or internally. GPIO63 is internally
connected to PWRBTN#. To toggle the
power button with software, GPIO63 must be
programmed as an output using the normal
GPIO programming protocol (see Section
6.4.1.1 "GPIO Support Registers" on page
240). GPIO63 must be pulsed low for at least
16 ms and not more than 4 sec.
Asserting POR# has no effect on ACPI. If
POR# is asserted and ACPI was active prior
to POR#, then ACPI will remain active after
POR#. Therefore, BIOS must ensure that
ACPI is inactive before GPIO63 is pulsed
low.
PWRCNT1
F31
AK6
O
PWRCNT2
G31
AL7
O
THRM#
F28
AK4
I
AMD Geode™ SC3200 Processor Data Book
Suspend Power Plane Control 1 and 2.
Control signal asserted during power management Suspend states. These signals are
open-drain outputs.
---
Thermal Event. Active low signal generated
by external hardware indicating that the system temperature is too high.
---
---
81
Revision 5.1
3.4.16
Signal Definitions
GPIO Interface Signals
Ball No.
Signal Name
EBGA
TEPBGA
Type
GPIO0
H1
D11
I/O
GPIO1
H2
D10
AL12
N30
GPIO6
AH3
GPIO7
Description
Mux
GPIO Port 0. Each signal is configured independently as an input or I/O, with or without
static pull-up, and with either open-drain or
totem-pole output type.
IOCS1#+TFTD12
D28
A debouncer and an interrupt can be enabled
or masked for each of signals GPIO[00:01]
and [06:15] independently.
DTR2#/BOUT2+
IDE_IOR1#+
SDTEST5
AH4
C30
Note:
GPIO8
AJ2
C31
GPIO9
AG4
C28
DCD2#+IDE_IOW1#+
SDTEST2
GPIO10
AJ1
B29
DSR2#+IDE_IORDY1
+SDTEST1
TRDE#
AB1D+IOCS1#
GPIO12, GPIO13, GPIO16 inputs: If RTS2#+IDE_DACK1#
GPIOx function is selected but not
+SDTEST0
used, tie GPIOx low.
CTS2#+IDE_DREQ1
+SDTEST4
GPIO11
H30
AJ8
RI2#+IRQ15
GPIO12
AJ12
N29
AB2C
GPIO13
AL11
M29
AB2D
GPIO14
F1
D9
IOR#+DOCR#
GPIO15
G3
A8
IOW#+DOCW#
GPIO16
AL15
V31
PC_BEEP+
F_DEVSEL#
GPIO17
J4
A10
IOCS0#+TFTDCK
GPIO18
A28
AG1
DTR1#/BOUT1
GPIO19
H4
C9
INTC#+IOCHRDY
GPIO20
H3
A9
DOCCS#+TFTD0
AJ13
N31
AB1C+DOCCS#
GPIO32
AJ11
M28
GPIO33
AL10
L31
GPIO34
AK10
L30
GPIO35
AJ10
L29
GPIO36
AL9
L28
GPIO37
AK9
K31
LFRAME#
GPIO38/IRRX2
AJ9
K28
LPCPD#
GPIO39
AL8
J31
SERIRQ
GPIO40
A21
Y3
IDE_DATA8
GPIO41
C19
W4
IDE_DATA11
82
I/O
GPIO Port 1. Each signal is configured independently as an input or I/O, with or without
static pull-up, and with either open-drain or
totem-pole output type.
A debouncer and an interrupt can be enabled
or masked for each of signals GPIO[32:41]
independently.
LAD0
LAD1
LAD2
LAD3
LDRQ#
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
3.4.17
Debug Monitoring Interface Signals
Ball No.
Signal Name
EBGA
TEPBGA
Type
FPCICLK
U3
B18
O
F_AD7
U1
A18
O
F_AD6
V3
A20
O
F_AD5
V2
C19
O
F_AD4
V1
C18
O
PD4+TFTD10
F_AD3
W2
C20
O
PD3+TFTD9
F_AD2
W3
D20
O
PD2+TFTD8
F_AD1
Y1
A21
O
PD1+TFTD7
F_AD0
AA1
C21
O
PD0+TFTD6
F_C/BE3#
T4
C17
O
SLCT+TFTD15
F_C/BE2#
T3
D17
O
PE+TFTD14
F_C/BE1#
T1
B17
O
BUSY/WAIT#+
TFTD3
F_C/BE0#
AA3
D21
O
ERR#+TFTD4+
F_FRAME#
AB1
A22
O
STB#/WRITE#+
TFTD17
F_IRDY#
W1
B20
O
SLIN#/ASTRB#+
TFTD16
F_STOP#
AJ15
U29
O
AC97_RST#
F_DEVSEL#
AL15
V31
O
GPIO16+
PC_BEEP
F_GNT0#
AK14
U31
O
SDATA_IN
F_TRDY#
AL14
U30
O
BIT_CLK
INTR_O
AB2
D22
O
CPU Core Interrupt. When enabled, this signal provides for monitoring of the internal
GX1 core INTR signal for debug purposes.
To enable, pull up FPCI_MON (EBGA ball
D3 / TEPBGA ball A4).
AFD#/DSTRB#+
TFTD2
SMI_O
Y3
B21
O
System Management Interrupt. This is the
input to the GX1 core. When enabled, this
signal provides for monitoring of the internal
GX1 core SMI# signal for debug purposes.
To enable, pull up FPCI_MON (EBGA ball
D3 / TEPBGA ball A4).
INIT#+TFTD5+
AMD Geode™ SC3200 Processor Data Book
Description
Fast-PCI Bus Monitoring Signals. When
enabled, this group of signals provides for
monitoring of the internal Fast-PCI bus for
debug purposes. To enable, pull up
FPCI_MON (EBGA ball D3 / TEPBGA ball
A4).
Mux
ACK#+TFTDE
PD7+TFTD13
PD6+TFTD1
PD5+TFTD11
83
Revision 5.1
3.4.18
Signal Definitions
JTAG Interface Signals
Ball No.
Signal Name
EBGA
TEPBGA
Type
Description
Mux
TCK
AL4
E31
I
JTAG Test Clock. This signal has an internal weak pull-up resistor.
---
TDI
AK5
F29
I
JTAG Test Data Input. This signal has an
internal weak pull-up resistor.
---
TDO
AH6
E30
O
JTAG Test Data Output
---
TMS
AJ5
F28
I
JTAG Test Mode Select. This signal has an
internal weak pull-up resistor.
---
TRST#
AK4
E29
I
JTAG Test Reset. This signal has an internal weak pull-up resistor.
---
For normal JTAG operation, this signal
should be active at power-up.
If the JTAG interface is not being used, this
signal can be tied low.
3.4.19
Test and Measurement Interface Signals
Ball No.
Signal Name
EBGA
TEPBGA
Type
GXCLK
AL16
V30
O
GX Clock. This signal is for internal testing
only. For normal operation either program as
FP_VDD_ON or leave unconnected.
FP_VDD_ON+
TEST3
TEST3
AL16
V30
O
Internal Test Signal. This signal is used for
internal testing only. For normal operation
leave unconnected, unless programmed as
FP_VDD_ON.
FP_VDD_ON+
GXCLK
TEST2
B29
AJ1
O
TEST1
C28
AG4
O
TEST0
D28
AH3
O
Internal Test Signals. These signals are
used for internal testing only. For normal
operation, leave unconnected unless programmed as one of their muxed options.
GTEST
AL5
F30
I
Global Test. This signal is used for internal
testing only. For normal operation this signal
should be pulled down with 1.5 KΩ.
---
PLL6B
C28
AG4
I/O
TEST1
PLL5B
B29
AJ1
I/O
PLL6, PLL5 and PLL2 Bypass. These signals are used for internal testing only. For
normal operation leave unconnected.
PLL2B
D28
AH3
I/O
84
Description
Mux
PLL5B
PLL6B
PLL2B
TEST2
TEST0
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Signal Definitions
3.4.19
Test and Measurement Interface Signals (Continued)
Ball No.
Signal Name
EBGA
TEPBGA
Type
SDTEST5
AH3
D28
O
SDTEST4
AJ2
C31
O
SDTEST3
AJ4
E28
O
SIN2
SDTEST2
AG4
C28
O
GPIO9+DCD2#+
IDE_IOW1#
SDTEST1
AJ1
B29
O
GPIO10+DSR2#
+IDE_IORDY1
SDTEST0
AH4
C30
O
GPIO7+RTS2#+
IDE_DACK1#
TDP
AH5
D30
I/O
TDN
AL3
D31
I/O
AMD Geode™ SC3200 Processor Data Book
Description
Memory Internal Test Signals. These signals are used for internal testing only. For
normal operation, these signals should be
programmed as one of their muxed options.
Thermal Diode Positive / Negative. These
signals are for internal testing only. For normal operation leave unconnected.
Mux
GPIO6+
DTR2#/BOUT2+
IDE_IOR1#
GPIO8+CTS2#+
IDE_DREQ1
-----
85
Revision 5.1
3.4.20
Signal Definitions
Power, Ground and No Connections1
Ball No.
Signal Name
EBGA
TEPBGA
Type
Description
AVSSPLL2
R3
C16
GND
Analog PLL2 Ground Connection.
AVSSPLL3
E28
AK3
GND
Analog PLL3 Ground Connection.
VPLL2
R1
A17
PWR
3.3V PLL2 Analog Power Connection. Low noise
power for PLL2 and PLL5.
VPLL3
C31
AJ4
PWR
3.3V PLL3 Analog Power Connection. Low noise
power for PLL3, PLL4, and PLL6.
AVCCUSB
AF4
D27
PWR
3.3V Analog USB Power Connection. Low noise
power.
AVSSUSB
AG1
C27
GND
Analog USB Ground Connection.
VBAT
D30
AL3
PWR
Battery. Provides battery back-up to the RTC and
ACPI registers, when VSB is lower than the minimum
value (see Table 9-3 on page 370). The ball is connected to the internal logic through a series resistor for
UL protection. If battery backup is not desired, connect
VBAT to VSS.
VSB
F29
AL5
PWR
3.3V Standby Power Supply. Provides power to the
Real-Time Clock (RTC) and ACPI circuitry while the
main power supply is turned off.
VSBL
H28
AL6
PWR
1.8V Standby Power Supply. Provides power to the
internal logic while the main power supply is turned off.
This signal requires a 0.1 µF bypass capacitor to VSS.
This supply must be present when VSB is present.
VCORE
SeeTable 3-3
on page 38.
(Total of 26)
See Table 3-5
on page 54.
(Total of 29)
PWR
1.8V Core Processor Power Connections.
VIO
See Table 3-3
on page 38.
(Total of 35)
See Table 3-5
on page 54.
(Total of 46)
PWR
3.3V I/O Power Connections.
VSS
See Table 3-3
on page 38.
(Total of 61)
See Table 3-5
on page 54.
(Total of 96)
GND
Ground Connections.
NC
See Table 3-3
on page 38.
(Total of 13)
See Table 3-5
on page 54.
(Total of 13)
---
1.
86
No Connections. These lines should be left disconnected. Connecting a pull-up/-down resistor or to an
active signal could cause unexpected results and possible malfunctions.
All power sources except VBAT must be connected, even if the function is not used.
AMD Geode™ SC3200 Processor Data Book
General Configuration Block
Revision 5.1
4
4.0General Configuration Block
The General Configuration block includes registers for:
• Pin Multiplexing and Miscellaneous Configuration
• WATCHDOG Timer
• High-Resolution Timer
• Clock Generators
A selectable interrupt is shared by all these functions.
not have a register block in PCI configuration space (i.e.,
they do not appear to software as PCI registers).
After system reset, the Base Address register is located at
I/O address 02EAh. This address can be used only once.
Before accessing any PCI registers, the BOOT code must
program this 16-bit register to the I/O base address for the
General Configuration block registers. All subsequent
writes to this address, are ignored until system reset.
Note:
4.1
Configuration Block Addresses
Registers of the General Configuration block are I/O
mapped in a 64-byte address range. These registers are
physically connected to the internal Fast-PCI bus, but do
Location of the General Configuration Block cannot be determined by software. See the AMD
Geode™ SC3200 Specification Update document.
Reserved bits in the General Configuration block should
read as written unless otherwise specified.
Table 4-1. General Configuration Block Register Summary
Offset
Width (Bits)
Type
Name
00h-01h
16
R/W
WDTO. WATCHDOG Timeout
0000h
Page 96
02h-03h
16
R/W
WDCNFG. WATCHDOG Configuration
0000h
Page 96
04h
8
R/WC
00h
Page 97
05h-07h
---
---
RSVD. Reserved
08h-0Bh
32
RO
TMVALUE. TIMER Value
0Ch
8
R/W
0Dh
8
R/W
0Eh-0Fh
---
---
RSVD. Reserved
10h
8
RO
MCCM. Maximum Core Clock Multiplier
11h
---
---
RSVD. Reserved
12h
8
R/W
13h-17h
---
---
18h-1Bh
32
R/W
1Ch-1Dh
---
---
1Eh-1Fh
16
R/W
20h-2Fh
---
---
30h-33h
32
R/W
34h-37h
32
38h
39h-3Bh
3Ch
WDSTS. WATCHDOG Status
Reset Value
Reference
---
---
xxxxxxxxh
Page 98
TMSTS. TIMER Status
00h
Page 98
TMCNFG. TIMER Configuration
00h
Page 98
PPCR. PLL Power Control
RSVD. Reserved
PLL3C. PLL3 Configuration
RSVD. Reserved
CCFC. Core Clock Frequency Control
RSVD. Reserved
---
---
Strapped Value
Page 103
---
---
2Fh
Page 103
---
---
E1040005h
Page 103
---
---
Strapped Value
Page 104
---
---
PMR. Pin Multiplexing Register
00000000h
Page 88
R/W
MCR. Miscellaneous Configuration Register
00000001h
Page 92
8
R/W
INTSEL. Interrupt Selection
00h
Page 94
---
---
RSVD. Reserved
---
---
8
RO
ID. Device ID
xxh
Page 94
3Dh
8
RO
REV. Revision
xxh
Page 94
3Eh-3Fh
16
RO
CBA. Configuration Base Address
xxxxh
Page 94
AMD Geode™ SC3200 Processor Data Book
87
Revision 5.1
4.2
General Configuration Block
Multiplexing, Interrupt Selection, and Base Address Registers
The registers described inTable 4-2 are used to determine
general configuration for the SC3200. These registers also
indicate which multiplexed signals are issued via balls from
which more than one signal may be output. For more infor-
mation about multiplexed signals and the appropriate configurations, see Section 3.1 "Ball Assignments" on page
27.
Table 4-2. Multiplexing, Interrupt Selection, and Base Address Registers
Bit
Description
Offset 30h-33h
Pin Multiplexing Register - PMR (R/W)
Reset Value: 00000000h
This register configures pins with multiple functions. See Section 3.1 on page 27 for more information about multiplexing information.
31:30
29
28
Reserved: Always write 0.
Test Signals. Selects ball functions.
Ball #
EBGA / TEPBGA
0: Internal Test Signals
Name
Add’l Dependencies
1: Internal Test Signals
Name
Add’l Dependencies
D28 / AH3
PLL2B
None
TEST0
None
C28 / AG4
PLL6B
None
TEST1
None
B29 / AJ1
PLL5B
None
TEST2
None
AL16 / V30
GXCLK
See PMR[23]
TEST3
PMR[23] = 0
Test Signals. Selects ball function.
Ball #
EBGA / TEPBGA
0: AC97 Signal
Name
Add’l Dependencies
1: Internal Test Signal
Name
Add’l Dependencies
AJ4 / E28
SIN2
None
SDTEST3
Note:
27
See Note.
If this bit is set, PMR[8] and PMR[18] must be set by software.
FPCI_MON (Fast-PCI Monitoring). Selects Fast-PCI monitoring output signals instead of Parallel Port signals.
Fast-PCI monitoring output signals can be enabled in two ways: by setting this bit to 1 or by strapping FPCI_MON (EBGA
ball D3 / TEPBGA ball A4) high. (The strapped value can be read back at MCR[30].) Listed below is how these two options
work together and the signals that are enabled (enabling overrides add’l dependencies except FPCI_MON = 1). Note that
the FPCI monitoring signals that are muxed with Audio signals are not enabled via this bit. They are only enabled using the
strap option.
PMR[27] FPCI_MON
0
0
1
1
88
0
1
0
1
Disable all Fast-PCI monitoring signals
Enable all Fast-PCI monitoring signals
Enable Fast-PCI monitoring signals muxed with Parallel Port signals only
Enable all Fast-PCI monitoring signals
Ball #
EBGA / TEPBGA
FPCI_MON Signal Other Signal
Add’l Dependencies
U3 / B18
U1 / A18
V3 / A20
V2 / C19
V1 / C18
W2 / C20
W3 / D20
Y1 / A21
AA1 / C21
T4 / C17
T3 / D17
T1 / B17
AA3 / D21
AB1 / A22
W1 / B20
AB2 / D22
Y3 / B21
FPCICLK
F_AD7
F_AD6
F_AD5
F_AD4
F_AD3
F_AD2
F_AD1
F_AD0
F_C/BE3#
F_C/BE2#
F_C/BE1#
F_C/BE0#
F_FRAME#
F_IRDY#
INTR_O
SMI_O
ACK#+TFTDE
PD7+TFTD13
PD6+TFTD1
PD5+TFT11
PD4+TFTD10
PD3+TFTD9
PD2+TFTD8
PD1+TFTD7
PD0_TFTD5
SLCT+TFTD15
PE+TFTD14
BUSY/WAIT#+TFTD3
ERR#+TFTD4
STB#/WRITE#+TFTD7
SLIN#/ASTRB#+TFTD16
AFD#/DSTRB#+TFTD2
INIT#+TFTD5
See PMR[23]
See PMR[23]
See PMR[23]
See PMR[23]
See PMR[23]
See PMR[23]
See PMR[23]
See PMR[23]
See PMR[23]
See PMR[23]
See PMR[23]
See PMR[23]
See PMR[23]
See PMR[23]
See PMR[23]
See PMR[23]
See PMR[23]
AL15 / V31
AJ15 / U29
AK14 / U31
AL14 / U30
F_DEVSEL#
F_STOP#
F_GNT0#
F_TRDY#
GPIO16+PC_BEEP
AC97_RST#
SDATA_IN
BIT_CLK
FPCI_MON = 1 and see PMR[0]
FPCI_MON = 1
FPCI_MON = 1
FPCI_MON = 1
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
General Configuration Block
Table 4-2. Multiplexing, Interrupt Selection, and Base Address Registers (Continued)
Bit
Description
26
Reserved. Always write 0.
25
AC97CKEN (Enable AC97_CLK Output). This bit enables the output drive of AC97_CLK (EBGA ball AJ14 / TEPBGA ball
P31).
0: AC97_CLK output is HiZ.
1: AC97_CLK output is enabled.
24
TFTIDE (TFT/IDE). Determines whether certain balls are used for TFT signals or for IDE signals. Note that there are no
additional dependencies.
Ball #
EBGA / TEPBGA
A26 / AD3
0: IDE Signals
Name
IDE_ADDR0
1: GPIO and TFT Signals
Name
TFTD3
C26 / AE1
IDE_ADDR1
TFTD2
C17 / U2
IDE_ADDR2
TFTD4
B24 / AC3
IDE_DATA0
TFTD6
A24 / AC1
IDE_DATA1
TFTD16
D23 / AC2
IDE_DATA2
TFTD14
C23 / AB4
IDE_DATA3
TFTD12
B23 / AB1
IDE_DATA4
FP_VDD_ON
A23 / AA4
IDE_DATA5
CLK27M
C22 / AA3
IDE_DATA6
IRQ9
B22 / AA2
IDE_DATA7
INTD#
A21 / Y3
IDE_DATA8
GPIO40
C20 / Y2
IDE_DATA9
DDC_SDA
A20 / Y1
IDE_DATA10
DDC_SCL
C19 / W4
IDE_DATA11
GPIO41
B19 / W3
IDE_DATA12
TFTD13
A19 / V3
IDE_DATA13
TFTD15
C18 / V2
IDE_DATA14
TFTD17
B18 / V1
IDE_DATA15
TFTD7
A27 / AF2
IDE_CS0#
TFTD5
C16 / P2
IDE_CS1#
TFTDE
C21 / Y4
IDE_IOR0#
TFTD10
D24 / AD2
IDE_IOW0#
TFTD9
C24 / AC4
IDE_DREQ0
TFTD8
C25 / AD4
IDE_DACK0#
TFTD0
A22 / AA1
IDE_RST#
TFTDCK
A25 / AD1
IDE_IORDY0
TFTD11
D25 / AF1
IRQ14
TFTD1
AMD Geode™ SC3200 Processor Data Book
89
Revision 5.1
General Configuration Block
Table 4-2. Multiplexing, Interrupt Selection, and Base Address Registers (Continued)
Bit
Description
23
TFTPP (TFT/Parallel Port). Determines whether certain balls are used for TFT or PP/ACB1/FPCI. This bit is set to 1 at
power-on if the TFT_PRSNT strap (EBGA ball AK13 / TEPBGA ball P29) is pulled high.
Ball #
EBGA / TEPBGA
0: PP/ACB1/FPCI
Name
Add’l Dependencies
1: TFT
Name
Add’l Dependencies
H2 / D10
GPIO1
IOCS1#
PMR[13] = 0
PMR[13] = 1
TFTD12
None
H3 / A9
GPIO20
DOCCS#
PMR[7] = 0
PMR[7] = 1
TFTD0
None
J4 / A10
GPIO17
IOCS0#
PMR[5] = 0
PMR[5] = 1
TFTDCK
None
T1 / B17
BUSY/WAIT#
F_C/BE1#
Note 1
Note 2
TFTD3
None
T3 / D17
PE
F_C/BE2#
Note 1
Note 2
TFTD14
Note 1
T4 / C17
SLCT
F_C/BE3#
Note 1
Note 2
TFTD15
Note 1
U1 / A18
PD7
F_AD7
Note 1
Note 2
TFTD13
Note 1
U3 / B18
ACK#
FPCICLK
Note 1
Note 2
TFTDE
Note 1
V1 / C18
PD4
F_AD4
Note 1
Note 2
TFTD10
Note 1
V2 / C19
PD5
F_AD5
Note 1
Note 2
TFTD11
Note 1
V3 / A20
PD6
F_AD6
Note 1
Note 2
TFTD1
Note 1
W1 / B20
SLIN#/ASTRB#
F_IRDY#
Note 1
Note 2
TFTD16
Note 1
W2 / C20
PD3
F_AD3
Note 1
Note 2
TFTD9
Note 1
W3 / D20
PD2
F_AD2
Note 1
Note 2
TFTD8
Note 1
Y1 / A21
PD1
F_AD1
Note 1
Note 2
TFTD7
Note 1
Y3 / B21
INIT#
SMI_O
Note 1
Note 2
TFTD5
Note 1
AA1 / C21
PD0
F_AD0
Note 1
Note 2
TFTD6
Note 1
AA3 / D21
ERR#
F_C/BE0#
Note 1
Note 2
TFTD4
Note 1
AB1 / A22
STB#/WRITE#
F_FRAME#
Note 1
Note 2
TFTD17
None
AB2 / D22
AFD#/DSTRB#
INTR_O
Note 1
Note 2
TFTD2
Note 1
AJ13 / N31
AB1C
None
GPIO20
DOCCS#
PMR[7] = 0
PMR[7] = 1
AL12 / N30
AB1D
None
GPIO1
IOCS1#
PMR[13] = 0
PMR[13] = 1
AL16 / V30
GXCLK
TEST3
PMR[29] = 0
PMR[29] = 1
FP_VDD_ON
None
Note:
22
90
1. PMR[27] = 0 and FPCI_MON = 0
2. PMR[27] = 1 or FPCI_MON = 1
3. ACCESS.bus interface 1 is not available if PMR[23] = 1.
4. If FPCI_MON strap is enabled, the TFT_PRSNT strap should pulled low.
RSVD (Reserved). Must be set equal to PMR[14] (LPCSEL). The LPC_ROM strap (EBGA ball E4 / TEPBGA ball D6) determines the power-on reset (POR) state of PMR[14] and PMR[22].
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
General Configuration Block
Table 4-2. Multiplexing, Interrupt Selection, and Base Address Registers (Continued)
Bit
Description
21
IOCSEL (Select I/O Commands). Selects ball functions.
Ball #
EBGA / TEPBGA
0: I/O Command Signals
Name
Add’l Dependencies
1: GPIO Signals
Name
Add’l Dependencies
F1 / D9
IOR#
DOCR#
PMR[2] = 0
PMR[2] = 1
GPIO14
Undefined
PMR[2] = 1
PMR[2] = 0
G3 / A8
IOW#
DOCW#
PMR[2] = 0
PMR[2] = 1
GPIO15
Undefined
PMR[2] = 1
PMR[2] = 0
20
Reserved. Must be set to 0.
19
AB2SEL (Select ACCESS.bus 2). Selects ball functions.
18
17
16
Ball #
EBGA / TEPBGA
0: GPIO Signals
Name
Add’l Dependencies
1: ACCESS.bus 2 Signals
Name
Add’l Dependencies
AJ12 / N29
GPIO12
None
AB2C
None
AL11 / M29
GPIO13
None
AB2D
None
SP2SEL (Select SP2 Additional Pins). Selects ball functions.
Ball #
EBGA / TEPBGA
0: GPIO, IDE Signals
Name
Add’l Dependencies
1: Serial Port Signals
Name
Add’l Dependencies
AH3 / D28
GPIO6
IDE_IOR1#
PMR[8] = 0
PMR[8] = 1
DTR2#/BOUT2
SDTEST5
PMR[8] = 0
PMR[8] = 1
AG4 / C28
GPIO9
IDE_IOW1#
PMR[8] = 0
PMR[8] = 1
DCD2#
SDTEST2
PMR[8] = 0
PMR[8] = 1
AJ1 / B29
GPIO10
IDE_IORDY1
PMR[8] = 0
PMR[8] = 1
DSR2#
SDTEST1
PMR[8] = 0
PMR[8] = 1
H30 / AJ8
GPIO11
IRQ15
PMR[8] = 0
PMR[8] = 1
RI2#
Undefined
PMR[8] = 0
PMR[8] = 1
SP2CRSEL (Select SP2 Flow Control). Selects ball functions.
Ball #
EBGA / TEPBGA
0: GPIO, IDE Signals
Name
Add’l Dependencies
1: Serial Port Signals
Name
Add’l Dependencies
AH4 / C30
GPIO7
IDE_DACK1#
PMR[8] = 0
PMR[8] = 1
RTS2#
SDTEST0
PMR[8] = 0
PMR[8] = 1
AJ2 / C31
GPIO8
IDE_DREQ1
PMR[8] = 0
PMR[8] = 1
CTS2#
SDTEST4
PMR[8] = 0
PMR[8] = 1
SP1SEL (Select SP1 Additional Pin). Selects ball function.
Ball #
EBGA / TEPBGA
0: GPIO Signal
Name
Add’l Dependencies
1: Serial Port Signal
Name
Add’l Dependencies
A28 / AG1
GPIO18
None
DTR1#/BOUT1
None
15
RSVD (Reserved). Write to 0.
14
LPCSEL (Select LPC Bus). Selects ball functions. The LPC_ROM strap (EBGA ball E4 / TEPBGA ball D6) determines the
power-on reset (POR) state of PMR[14] and PMR[22].
13
Ball #
EBGA / TEPBGA
0: GPIO Signals
Name
Add’l Dependencies
1: LPC Signals
Name
Add’l Dependencies
AJ11 / M28
GPIO32
PMR[22] = 0
LAD0
PMR[22] = 1
AL10 / L31
GPIO33
PMR[22] = 0
LAD1
PMR[22] = 1
AK10 / L30
GPIO34
PMR[22] = 0
LAD2
PMR[22] = 1
AJ10 / L29
GPIO35
PMR[22] = 0
LAD3
PMR[22] = 1
AL9 / L28
GPIO36
PMR[22] = 0
LDRQ#
PMR[22] = 1
AK9 / K31
GPIO37
PMR[22] = 0
LFRAME#
PMR[22] = 1
AJ9 / K28
GPIO38/IRRX2
PMR[22] = 0
LPCPD#
PMR[22] = 1
AL8 / J31
GPIO39
PMR[22] = 0
SERIRQ
PMR[22] = 1
IOCS1SEL (Select IOCS1). Selects ball functions for IOCS1# or GPIO1. Works in conjunction with PMR[23], see PMR[23]
for definition.
AMD Geode™ SC3200 Processor Data Book
91
Revision 5.1
General Configuration Block
Table 4-2. Multiplexing, Interrupt Selection, and Base Address Registers (Continued)
Bit
Description
12
TRDESEL (Select TRDE#). Selects ball function.
11
Ball #
EBGA / TEPBGA
0: Sub-ISA Signal
Name
Add’l Dependencies
1: GPIO Signal
Name
Add’l Dependencies
H1 / D11
TRDE#
GPIO0
None
None
EIDE (Enable IDE Outputs). This bit enables IDE output signals.
0: IDE signals are HiZ. Other signals multiplexed on the same balls are HiZ until this bit is set. (without regard to bit 24 of
this register). This bit does not control IDE channel 1 control signals selected by bit 8 of this register.
1:
10
Signals are enabled.
ETFT (Enable TFT Outputs). This bit enables TFT output signals, that are multiplexed with the Parallel Port and controlled
by PMR[23].
0: Signals TFTD[17:0], TFTDE and TFTDCK are set to 0.
1: Signals TFTD[17:0], TFTDE and TFTDCK are enabled.
Note:
9
TFTDCK that is multiplexed on IDE_RST# (EBGA ball A22 / TEPBGA ball AA1) is also enabled by this bit.
IOCHRDY (Select IOCHRDY). Selects ball function.
Ball #
EBGA / TEPBGA
0: PCI, GPIO Signal
Name
Add’l Dependencies
1: Sub-ISA Signal
Name
Add’l Dependencies
H4 / C9
GPIO19
INTC#
IOCHRDY
Undefined
PMR[4] = 0
PMR[4] = 1
PMR[4] = 1
PMR[4] = 0
8
IDE1SEL (Select IDE Channel 1). Selects IDE Channel 1 or GPIO ball functions. Works in conjunction with PMR[18] and
PMR[17], see PMR[18] and PMR[17] for definitions.
7
DOCCSSEL (Select DOCCS#). Selects DOCCS# or GPIO20 ball functions. Works in conjunction with PMR[23], see
PMR[23] for definition.
6
SP3SEL (Select UART3). Selects ball functions.
Ball #
EBGA / TEPBGA
0: IR Signals
Name
Add’l Dependencies
1: Serial Port Signals
Name
Add’l Dependencies
J28 / AK8
IRRX1
None
SIN3
None
J3 / C11
IRTX
None
SOUT3
None
5
IOCS0SEL (Select IOCS0#). Selects ball function. Works in conjunction with PMR[23], see PMR[23] for definition.
4
INTCSEL (Select INTC#). Selects ball function. Works in conjunction with PMR[9], see PMR[9] for definition.
3
Reserved. Write as read.
2
DOCWRSEL (Select DiskOnChip and NAND Flash Command Lines). Selects ball functions. Works in conjunction with
PMR[21], see PMR[21] for definition.
1
Reserved. Write as read.
0
PCBEEPSEL (Select PC_BEEP). Selects ball function.
Ball #
EBGA / TEPBGA
0: GPIO Signal
Name
Add’l Dependencies
1: Audio Signal
Name
Add’l Dependencies
AL15 / V31
GPIO16
F_DEVSEL#
FPCI_MON = 0
FPCI_MON = 1
PC_BEEP
F_DEVSEL#
FPCI_MON] = 0
FPCI_MON = 1
Offset 34h-37h
Miscellaneous Configuration Register - MCR (R/W)
Power-on reset value: The BOOT16 strap pin selects "Enable 16-Bit Wide Boot Memory".
Reset Value: 0000001h
31
DID0 (EBGA Ball D4 / TEPBGA Ball C5) Strap Status. (Read Only) Represents the value of the strap that is latched after
power-on reset. Read in conjunction with bit 29.
30
FPCI_MON (EBGA Ball D3 / TEPBGA Ball A4) Strap Status. (Read Only) Represents the value of the strap that is
latched after power-on reset. Indicates if Fast-PCI monitoring output signals (instead of Parallel Port and some audio signals) are enabled. The state of this bit along with PMR[27] control the Fast-PCI monitoring function. See PMR[27] definition.
29
DID1 (EBGA Ball D2 / TEPBGA Ball C6) Strap Status. (Read Only) Represents the value of the strap that is latched after
power-on reset. Read in conjunction with bit 31.
28:20
Reserved.
19:18
Reserved. Write as 0.
17
HSYNC Timing. HSYNC timing control for TFT.
0: Reserved.
1: HSYNC timing suited for TFT.
92
AMD Geode™ SC3200 Processor Data Book
General Configuration Block
Revision 5.1
Table 4-2. Multiplexing, Interrupt Selection, and Base Address Registers (Continued)
Bit
Description
16
Delay HSYNC. HSYNC delay by two TFT clock cycles.
0: There is no delay on HSYNC.
1: HYSNC is delayed twice by rising edge of TFT clock. Enables delay between VSYNC and HSYNC suited for TFT display.
15
Reserved. Write as read.
14
IBUS16 (Invert BUS16). This bit inverts the meaning of MCR[3] (bit 3 of this register).
0: BUS16 is as described for MCR[3].
1: BUS16 meaning is inverted: if MCR[3] = 0, ROMCS# access is 16 bits wide; if MCR[3] = 1, ROMCS# access is 8 bits
wide.
13
Reserved. Must be set to 0.
12
IO1ZWS (Enable ZWS# for IOCS1# Access). This bit enables internal activation of ZWS# (Zero Wait States) control for
IOCS1# access.
0: ZWS# is not active for IOCS1# access.
1: ZWS# is active for IOCS1# access.
11
IO0ZWS (Enable ZWS# for IOCS0# Access). This bit enables internal activation of ZWS# (Zero Wait States) control for
IOCS0# access.
0: ZWS# is not active for IOCS0# access.
1: ZWS# is active for IOCS0# access.
10
DOCZWS (Enable ZWS# for DOCCS# Access). This bit enables internal activation of ZWS# (Zero Wait States) control for
DOCCS# access.
0: ZWS# is not active for DOCCS# access.
1: ZWS# is active for DOCCS# access.
9
ROMZWS (Enable ZWS# for ROMCS# Access). This bit enables internal activation of ZWS# (Zero Wait States) control for
ROMCS# access.
0: ZWS# is not active for ROMCS# access.
1: ZWS# is active for ROMCS# access.
8
IO1_16 (Enable 16-Bit Wide IOCS1# Access). This bit enables the16-line access to IOCS1# in the Sub-ISA interface.
0: 8-bit wide IOCS1# access is used.
1: 16-bit wide IOCS1# access is used.
7
IO0_16 (Enable 16-Bit Wide IOCS0# Access). This bit enables the 16-line access to IOCS0# in the Sub-ISA interface.
0: 8-bit wide IOCS0# access is used.
1: 16-bit wide IOCS0# access is used.
6
DOC16 (Enable 16-Bit Wide DOCCS# Access). This bit enables the 16-line access to DOCCS# in the Sub-ISA interface.
0: 8-bit wide DOCCS# access is used.
1: 16-bit wide DOCCS# access is used.
5
Reserved. Write as read.
4
IRTXEN (Infrared Transmitter Enable). This bit enables drive of Infrared transmitter output.
0: IRTX+SOUT3 line (EBGA ball J3 / TEPBGA ball C11) is HiZ.
1: IRTX+SOUT3 line (EBGA ball J3 / TEPBGA ball C11) is enabled.
3
BUS16 (16-Bit Wide Boot Memory). (Read Only) This bit reports the status of the BOOT16 strap (EBGA ball G4 / TEPBGA ball C8). If the BOOT16 strap is pulled high, at reset 16-bit access to ROM in the Sub-ISA interface is enabled.
MCR[14] = 1 inverts the meaning of this register.
0: 8-bit wide ROM.
1: 16-bit wide ROM.
2:1
Reserved. Write as read.
AMD Geode™ SC3200 Processor Data Book
93
Revision 5.1
General Configuration Block
Table 4-2. Multiplexing, Interrupt Selection, and Base Address Registers (Continued)
Bit
0
Description
SDBE0 (Slave Disconnect Boundary Enable). Works in conjunction with the GX1 module’s PCI Control Function 2 Register (Index 41h), bit 1 (SDBE1). Sets boundaries for when the GX1 module is a PCI slave.
SDBE[1:0]
00: Read and Write disconnect on boundaries set by bits [3:2] of the GX1 module’s PCI Control Function 2 register (Index
41h).
01: Write disconnects on boundaries set by bits [3:2] of the GX1 module’s PCI Control Function 2 register. Read disconnects on cache line boundary of 16 bytes.
1x: Read and Write disconnect on cache line boundary of 16 bytes.
This bit is reset to 1.
All PCI bus masters (including SC3200’s on-chip PCI bus masters, e.g., the USB Controller) must be disabled while modifying this bit. When accessing this register while any PCI bus master is enabled, use read-modify-write to ensure these bit
contents are unchanged.
Offset 38h
Interrupt Selection Register - INTSEL (R/W)
Reset Value: 00h
This register selects the IRQ signal of the combined WATCHDOG and High-Resolution timer interrupt. This interrupt is shareable with
other interrupt sources.
7:4
Reserved. Write as read.
3:0
CBIRQ. Configuration Block Interrupt.
0000: Disable
0100: IRQ4
1000: IRQ8#
1100: IRQ12
0001: IRQ1
0101: IRQ5
1001: IRQ9
1101: Reserved
0010: Reserved
0110: IRQ6
1010: IRQ10
1110: IRQ14
0011: IRQ3
0111: IRQ7
1011: IRQ11
1111: IRQ15
Offset 39h-3Bh
Reserved - RSVD
Offset 3Ch
Device Identification Number Register - ID (RO)
This register identifies the device. SC3200 = 04h.
Reset Value: xxh
Offset 3Dh
Revision Register - REV (RO)
Reset Value: xxh
This register identifies the device revision. See the AMD Geode™ SC3200 Specification Update document for value.
Offset 3Eh-3Fh
Configuration Base Address Register - CBA (RO)
This register sets the base address of the Configuration block.
94
Reset Value: xxh
15:6
Configuration Base Address. These bits are the high bits of the Configuration Base Address.
5:0
Configuration Base Address. These bits are the low bits of the Configuration Base Address. These bits are set to 0.
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
General Configuration Block
4.3
WATCHDOG
The SC3200 includes a WATCHDOG function to serve as
a fail-safe mechanism in case the system becomes hung.
When triggered, the WATCHDOG mechanism returns the
system to a known state by generating an interrupt, an
SMI, or a system reset (depending on configuration).
4.3.1
• The GX1 module’s internal SUSPA# signal is 1.
or
• The GX1 module’s internal SUSPA# signal is 0 and the
WD32KPD bit (Offset 02h[8]) is 0.
The 32 KHz input clock is disabled, when:
Functional Description
WATCHDOG is enabled when the WATCHDOG Timeout
(WDTO) register (Offset 00h) is set to a non-zero value.
The WATCHDOG timer starts with this value and counts
down until either the count reaches 0, or a trigger event
restarts the count (with the WDTO register value).
The WATCHDOG timer is restarted in any of the following
cases:
• The WDTO register is set with a non-zero value.
• The WATCHDOG timer reaches 0 and the WATCHDOG
Overflow bit, WDOVF (Offset 04h[0]), is 0.
The WATCHDOG function is disabled in any of the following cases:
• System reset occurs.
• The WDTO register is set to 0.
• The WDOVF bit is already 1 when the timer reaches 0.
4.3.1.1 WATCHDOG Timer
The WATCHDOG timer is a 16-bit down counter. Its input
clock is a 32 KHz clock divided by a predefined value (see
WDPRES field, Offset 02h[3:0]). The 32 KHz input clock is
enabled when either:
• The GX1 module’s internal SUSPA# signal is 0 and the
WD32KPD bit is 1.
For more information about signal SUSPA#, refer to the
AMD Geode™ GX1 Processor Data Book.
When the WATCHDOG timer reaches 0:
• If the WDOVF bit in the WDSTS register (Offset 04h[0])
is 0, an interrupt, an SMI or a system reset is generated,
depending on the value of the WDTYPE1 field in the
WDCNFG register (Offset 02h[5:4]).
• If the WDOVF bit in the WDSTS register is already 1
when the WATCHDOG timer reaches 0, an interrupt, an
SMI or a system reset is generated according to the
WDTYPE2 field (Offset 02h[7:6]), and the timer is
disabled. The WATCHDOG timer is re-enabled when a
non-zero value is written to the WDTO register (Offset
00h).
The interrupt or SMI is de-asserted when the WDOVF bit is
set to 0. The reset generated by the WATCHDOG function
is used to trigger a system reset via the Core Logic module. The value of the WDOVF bit, the WDTYPE1 field, and
the WDTYPE2 field are not affected by a system reset
(except when generated by power-on reset).
The SC3200 also allows no action to be taken when the
timer reaches 0 (according to WDTYPE1 field and
WDTYPE2 field). In this case only the WDOVF bit is set to
1.
Internal Fast-PCI Bus
WATCHDOG
WDTO
SUSPA#
32 KHz
WDPRES
POR#
Timer
WDOVF
WDTYPE1 or
WDTYPE2
Reset IRQ SMI
Figure 4-1. WATCHDOG Block Diagram
AMD Geode™ SC3200 Processor Data Book
95
Revision 5.1
General Configuration Block
WATCHDOG Interrupt
The WATCHDOG interrupt (if configured and enabled) is
routed to an IRQ signal. The IRQ signal is programmable
via the INTSEL register (Offset 38h, described in Table 4-2
"Multiplexing, Interrupt Selection, and Base Address Registers" on page 88). The WATCHDOG interrupt is a shareable, active low, level interrupt.
WATCHDOG SMI
The WATCHDOG SMI is recognized by the Core Logic
module as internal input signal EXT_SMI0#. To use the
WATCHDOG SMI, Core Logic registers must be configured
appropriately.
4.3.2
WATCHDOG Registers
Table 4-3 describes the WATCHDOG registers.
4.3.2.1
Usage Hints
• SMM code should set bit 8 of the WDCNFG register to 1
when entering ACPI C3 state, if the WATCHDOG timer
is to be suspended. If this is not done, the WATCHDOG
timer is functional during C3 state.
• SMM code should set bit 8 of the WDCNFG register to
1, when entering ACPI S1 and S2 states if the
WATCHDOG timer is to be suspended. If this is not
done, the WATCHDOG timer is functional during S1 and
S2 states.
Table 4-3. WATCHDOG Registers
Bit
Description
Offset 00h-01h
WATCHDOG Timeout Register - WDTO (R/W)
This register specifies the programmed WATCHDOG timeout period.
15:0
Reset Value: 0000h
Programmed timeout period.
Offset 02h-03h
WATCHDOG Configuration Register - WDCNFG (R/W)
Reset Value: 0000h
This register selects the signal to be generated when the timer reaches 0, whether or not to disable the 32 KHz input clock during low
power states, and the prescaler value of the clock input.
15:9
8
Reserved. Write as read.
WD32KPD (WATCHDOG 32 KHz Power Down).
0:
32 KHz clock is enabled.
1:
32 KHz clock is disabled, when the GX1 module asserts its internal SUSPA# signal.
This bit is cleared to 0, when POR# is asserted or when the GX1 module de-asserts its internal SUSPA# signal (i.e., on
SUSPA# rising edge). See Section 4.3.2.1 "Usage Hints" on page 96.
7:6
WDTYPE2 (WATCHDOG Event Type 2).
00: No action
01: Interrupt
10: SMI
11: System reset
This field is reset to 0 when POR# is asserted. Other system resets do not affect this field.
5:4
WDTYPE1 (WATCHDOG Event Type 1).
00: No action
01: Interrupt
10: SMI
11: System reset
This field is reset to 0 when POR# is asserted. Other system resets do not affect this field.
3:0
WDPRES (WATCHDOG Timer Prescaler). Divide 32 KHz by:
0000: 1
96
0100: 16
1000: 256
1100: 4096
0001: 2
0101: 32
1001: 512
1101: 8192
0010: 4
0110: 64
1010: 1024
1110: Reserved
0011: 8
0111: 128
1011: 2048
1111: Reserved
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
General Configuration Block
Table 4-3. WATCHDOG Registers (Continued)
Bit
Description
Offset 04h
WATCHDOG Status Register - WDSTS (R/WC)
This register contains WATCHDOG status information.
7:4
Reset Value: 00h
Reserved. Write as read.
3
WDRST (WATCHDOG Reset Asserted). (Read Only) This bit is set to 1 when WATCHDOG Reset is asserted. It is set to
0 when POR# is asserted, or when the WDOVF bit is set to 0.
2
WDSMI (WATCHDOG SMI Asserted). (Read Only) This bit is set to 1 when WATCHDOG SMI is asserted. It is set to 0
when POR# is asserted, or when the WDOVF bit is set to 0.
1
WDINT (WATCHDOG Interrupt Asserted. (Read Only) This bit is set to 1 when the WATCHDOG Interrupt is asserted. It
is set to 0 when POR# is asserted, or when the WDOVF bit is set to 0.
0
WDOVF (WATCHDOG Overflow). This bit is set to 1 when the WATCHDOG Timer reaches 0. It is set to 0 when POR# is
asserted, or when a 1 is written to this bit by software. Other system reset sources do not affect this bit.
Offset 05h-07h
4.4
Reserved - RSVD
High-Resolution Timer
The SC3200 provides an accurate time value that can be
used as a time stamp by system software. This time is
called the High-Resolution Timer. The length of the timer
value can be extended via software. It is normally enabled
while the system is in the C0 and C1 states. Optionally,
software can be programmed to enable use of the HighResolution Timer during C3 state and/or S1 state as well.
In all other power states the High-Resolution Timer is disabled.
The input clock (derived from the 27 MHz crystal oscillator)
is enabled when:
4.4.1
For more information about signal SUSPA# see Section
4.4.2.1 "Usage Hints" on page 97 and the AMD Geode™
GX1 Processor Data Book.
Functional Description
The High-Resolution Timer is a 32-bit free-running countup timer that uses the oscillator clock or the oscillator clock
divided by 27. Bit TMCLKSEL of the TMCNFG register
(Offset 0Dh[1]) can be set via software to determine which
clock should be used for the High-Resolution Timer.
When the most significant bit (bit 31) of the timer changes
from 1 to 0, bit TMSTS of the TMSTS register (Offset
0Ch[0]) is set to 1. When both bit TMSTS and bit TMEN
(Offset 0Dh[0]) are 1, an interrupt is asserted. Otherwise,
the interrupt is de-asserted. This interrupt enables software
emulation of a larger timer.
The High-Resolution Timer interrupt is routed to an IRQ
signal. The IRQ signal is programmable via the INTSEL
register (Offset 38h). For more information about this register, see section Section 4.2 "Multiplexing, Interrupt Selection, and Base Address Registers" on page 88.
System software uses the read-only TMVALUE register
(Offset 08h[31:0]) to read the current value of the timer.
The TMVALUE register has no default value.
AMD Geode™ SC3200 Processor Data Book
• The GX1 module’s internal SUSPA# signal is 1.
or
• The GX1 module’s internal SUSPA# signal is 0 and bit
TM27MPD (Offset 0Dh[2]) is 0.
The input clock is disabled, when the GX1 module’s internal SUSPA# signal is 0 and the TM27MPD bit is 1.
The High-Resolution Timer function resides on the internal
Fast-PCI bus and its registers are in General Configuration
Block address space. Only one complete register should
be accessed at-a-time (e.g., DWORD access should be
used for DWORD wide registers and byte access should be
used for byte-wide registers).
4.4.2
High-Resolution Timer Registers
Table 4-4 on page 98 describes the registers for the HighResolution Timer (TIMER).
4.4.2.1
Usage Hints
• SMM code should set bit 2 of the TMCNFG register to 1
when entering ACPI C3 state if the High-Resolution
Timer should be disabled. If this is not done, the HighResolution Timer is functional during C3 state.
• SMM code should set bit 2 of the TMCNFG register to 1
when entering ACPI S1 state if the High-Resolution
Timer should be disabled. If this is not done, the HighResolution Timer is functional during S1 state.
97
Revision 5.1
General Configuration Block
Table 4-4. High-Resolution Timer Registers
Bit
Description
Offset 08h-0Bh
TIMER Value Register - TMVALUE (RO)
This register contains the current value of the High-Resolution Timer.
31:0
Reset Value: xxxxxxxxh
Current Timer Value.
Offset 0Ch
TIMER Status Register - TMSTS (R/W)
This register supplies the High-Resolution Timer status information.
7:1
0
Reset Value: 00h
Reserved.
TMSTS (TIMER Status). This bit is set to 1 when the most significant bit (bit 31) of the timer changes from 1 to 0. It is
cleared to 0 upon system reset or when 1 is written by software to this bit.
Offset 0Dh
TIMER Configuration Register - TMCNFG (R/W)
Reset Value: 00h
This register enables the High-Resolution Timer interrupt; selects the Timer clock; and disables the 27 MHz internal clock during low
power states.
7:3
2
Reserved.
TM27MPD (TIMER 27 MHz Power Down). This bit is cleared to 0 when POR# is asserted or when the GX1 module deasserts its internal SUSPA# signal (i.e., on SUSPA# rising edge). See Section 4.4.2.1 "Usage Hints" on page 97.
0: 27 MHz input clock is enabled.
1: 27 MHz input clock is disabled when the GX1 module asserts its internal SUSPA# signal.
1
TMCLKSEL (TIMER Clock Select).
0: Count-up timer uses the oscillator clock divided by 27.
1: Count-up timer uses the oscillator clock, 27 MHz clock.
0
TMEN (TIMER Interrupt Enable).
0: High-Resolution Timer interrupt is disabled.
1: High-Resolution Timer interrupt is enabled.
Offset 0Eh-0Fh
98
Reserved - RSVD
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
General Configuration Block
4.5
Clock Generators and PLLs
This section describes the registers for the clocks required
by the GX1 module, Core Logic module, and the Video
Processor, and how these clocks are generated. See Figure 4-2 for a clock generation diagram.
The clock generators are based on 32.768 KHz and 27.000
MHz crystal oscillators. The 32.768 KHz crystal oscillator is
described in Section 5.5.2 "RTC Clock Generation" on
page 121 (functional description of the RTC).
Real-Time Clock (RTC)
32.768 KHz
32.768 KHz
Crystal
Oscillator
USB Clock (48 MHz)
and I/O Block Clock
PLL4
48 MHz
Shutdown
DISABLE
Shutdown
AC97_CLK
(24.576 MHz)
PLL3
24.576 MHz
27 MHz
Crystal
Oscillator
To PAD
High-Resolution Timer Clock
Shutdown
PLL6
57.273 MHz
Divide
by 4
ACPI Clock (14.318 MHz)
CLK27M Ball
Shutdown
Shutdown
PLL2
25-135 MHz
DISABLE
Shutdown
(ACPI)
Dot Clock
CLK
48 MHz
PLL5
66.67 MHz
Internal Fast-PCI Clock
66 MHz
33 MHz
Divide
by 2
ADL
100-333 MHz
External PCI Clock
(33.3 MHz)
DISABLE
Core Clock
Shutdown
(ACPI)
SDRAM Clock
Divider
Note:
VPLL2 powers PLL2 and PLL5. VPLL3 powers PLL3, PLL4, and PLL6.
Figure 4-2. Clock Generation Block Diagram
AMD Geode™ SC3200 Processor Data Book
99
Revision 5.1
4.5.1
General Configuration Block
27 MHz Crystal Oscillator
The internal oscillator employs an external crystal connected to the on-chip amplifier. The on-chip amplifier is
accessible on the X27I input and X27O output signals. See
Figure 4-3 for the recommended external circuit and Table
4-5 for a list of the circuit components.
To other
modules
Internal
External
X27O
X27I
Choose C1 and C2 capacitors to match the crystal’s load
capacitance. The load capacitance CL “seen” by crystal Y
is comprised of C1 in series with C2 and in parallel with the
parasitic capacitance of the circuit. The parasitic capacitance is caused by the chip package, board layout and
socket (if any), and can vary from 0 to 10 pF. The rule of
thumb in choosing these capacitors is:
R1
C1
R2
C2
Y
Figure 4-3. Recommended Oscillator External
Circuitry
CL = (C1 * C2) / (C1 + C2) + CPARASITIC
Example 1:
Crystal CL = 10 pF, CPARASITIC = 8.2 pF
C1 = 3.6 pF, C2 = 3.6 pF
Example 2:
Crystal CL = 20 pF, CPARASITIC = 8 pF
C1 = 24 pF, C2 = 24 pF
Table 4-5. Crystal Oscillator Circuit Components
Component
Parameters
Values
Tolerance
Crystal
Resonance Frequency
27.00 MHz Parallel mode
50 PPM or better
Type
AT-cut or BT-cut
Serial Resistance
40 Ω
Max
Shunt Capacitance
7 pF
Max
Load Capacitance, CL
10-20 pF
Temperature Coefficient
User-defined
Resistor R1
Resistance
20 MΩ
5%
Resistor R21
Resistance
100 Ω
5%
Capacitor C11
Capacitance
3-24 pF
5%
Capacitor C21
Capacitance
3-24 pF
5%
1.
100
The value of these components is recommended. It should be tuned according to crystal and board parameters.
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
General Configuration Block
4.5.2
GX1 Module Core Clock
Table 4-6. Core Clock Frequency
The core clock is generated by an Analog Delay Loop
(ADL) clock generator from the internal Fast-PCI clock. The
clock can be any whole-number multiple of the input clock
between 4 and 10. Possible values are listed in Table 4-6.
ADL
Multiplier
Value
Internal Fast-PCI Clock Freq. (MHz)
33.33
48
66.67
At power-on reset, the core clock multiplier value is set
according to the value of four strapped balls - CLKSEL[3:0]
(EBGA balls AL13, AK3, B27, F3 / TEPBGA balls P30,
D29, AF3, B8). These balls also select the clock which is
used as input to the multiplier, as shown in Table 4-7.
4
133.3
192
266.7
5
166.7
240
---
6
200
288
---
7
233.3
---
---
4.5.3
8
266.7
---
---
9
---
---
---
10
---
---
---
Internal Fast-PCI Clock
The internal Fast-PCI clock can be configured to 33, 48, or
66 MHz via strap options on the CLKSEL1 and CLKSEL0
balls. These can be read in the internal Fast-PCI Clock
field in the CCFC register (GCB+I/O Offset 1Eh[9:8]). (See
Table 4-8 on page 103 details on the CCFC register.)
Table 4-7. Strapped Core Clock Frequency
Default ADL Multiplier
CLKSEL[3:0]
Straps
Internal Fast-PCI Clock
Freq. (MHz)
(GCB+I/O Offset 1Eh[9:8])
Multiply By
Multiplier Value
(GCB+I/O Offset 1Eh[3:0])
Maximum Core
Clock Freq. (MHz)
0111
33.33
4
0100
133
1011
5
0101
167
1111
6
0110
200
0000
7
0111
233
0100
8
1000
266
1000
9
1001
Reserved
1100
10
1010
Reserved
0001
4
0100
192
0101
48
5
0101
240
1001
6
0110
288
1101
0110
66.67
1010
Note:
7
0111
Reserved
4
0100
266
5
0101
Reserved
Not all speeds are supported. For information on supported speeds, see Section A.1 "Order Information" on page
443.
AMD Geode™ SC3200 Processor Data Book
101
Revision 5.1
4.5.4
SuperI/O Clocks
The SuperI/O module requires a 48 MHz input for Fast
infrared (FIR), UART, and other functions. This clock is supplied by PLL4 using a multiplier value of 576/(108x3) to
generate 48 MHz.
4.5.5
Core Logic Module Clocks
The Core Logic module requires the following clock
sources:
Real-Time Clock (RTC)
RTC requires a 32.768 KHz clock which is supplied directly
from an internal low-power crystal oscillator. This oscillator
uses battery power and has very low current consumption.
USB
The USB requires a 48 MHz input which is supplied by
PLL4. The required total frequency accuracy and slow jitter
for USB is 500 PPM; edge to edge jitter is ±1.2%.
General Configuration Block
4.5.6
Video Processor Clocks
The Video processor requires the following clock sources:
Dot
The Dot clock is generated by PLL2. It is supplied to the
Display Controller in the GX1 module (DCLK) that creates
the pixel information, and is returned to the Graphics block
(PCLK) with this information. PLL2 uses the 27 MHz clock
to generate the Dot clock.
Video
The Video clock source depends on the source of the video
data.
• If the video data is coming from the GX1 module
(Capture Video mode), the video clock is generated by
the Display Controller.
• If the video data is coming directly from the VIP block
(Direct Video mode), the Video Clock is generated by
the VIP block.
ACPI
The ACPI logic block uses a 14.32 MHz clock supplied by
PLL6. PLL6 creates this clock from the 32.768 KHz clock,
with a multiplier value of 6992/4 to output a 57.278 MHz
clock that is divided by 4.
External PCI
The PCI Interface uses a 33.3 MHz clock that is created by
PLL5 and divided by 2. PLL5 uses the 27 MHz clock, to
output a 66.67 MHz clock. PLL5 has a frequency accuracy
of ± 0.1%.
AC97
The SC3200 generates the 24.576 MHz clock required by
the audio codec. Therefore, no crystal need be included for
the audio codec on the system board.
PLL3 uses the crystal oscillator clock, to generate a 24.576
MHz clock. This clock is driven on the AC97_CLK ball. The
accuracy of the clock supplied by the SC3200 is 50 PPM.
102
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
General Configuration Block
4.5.7
Clock Registers
Table 4-8 describes the registers of the clock generator and PLL.
Table 4-8. Clock Generator Configuration
Bit
Description
Offset 10h
Maximum Core Clock Multiplier Register - MCCM (RO)
Reset Value: Strapped Value
This register holds the maximum core clock multiplier value. The maximum clock frequency allowed by the core, is the Fast-PCI clock
multiplied by this value.
7:4
Reserved.
3:0
MCM (Maximum Clock Multiplier). This 4-bit value is the maximum multiplier value allowed for the core clock generator. It
is derived from strap pins CLKSEL[3:0] based on the multiplier value in Table 4-7 on page 101.
Offset 11h
Reserved - RSVD
Offset 12h
PLL Power Control Register - PPCR (R/W)
This register controls operation of the PLLs.
7
Reserved.
6
EXPCID (Disable External PCI Clock).
Reset Value: 2Fh
0: External PCI clock is enabled.
1: External PCI clock is disabled.
5
GPD (Disable Graphic Pixel Reference Clock).
0: PLL2 input clock is enabled.
1: PLL2 input clock is disabled.
4
Reserved.
3
PLL3SD (Shut Down PLL3). AC97 codec clock.
0: PLL3 is enabled.
1: PLL3 is shutdown.
2
FM1SD (Shut Down PLL4).
0: PLL4 is enabled.
1: PLL4 is shutdown, unless internal Fast-PCI clock is strapped to 48 MHz.
1
C48MD (Disable SuperI/O and USB Clock).
0: USB and SuperI/O clock is enabled.
1: USB and SuperI/O clock is disabled.
0
Reserved. Write as read.
Offset 13h-17h
Reserved - RSVD
Offset 18h-1Bh
PLL3 Configuration Register - PLL3C (R/W)
31:24
Reset Value: E1040005h
MFFC (MFF Counter Value).
Fvco
= OSCCLK * MFBC / (MFFC * MOC)
OSCCLK = 27 MHz
23:19
Reserved. Write as read.
18:8
MFBC (MFB Counter Value).
Fvco
= OSCCLK * MFBC / (MFFC * MOC)
OSCCLK = 27 MHz
Note:
Bits 18, 9, and 8 cannot be changed. Bit 18 is always a 1; bits 9 and 8 are always 0.
7
Reserved. Write as read.
6
Reserved. Must be set to 0.
5:0
MOC (MO Counter Value).
Fvco
= OSCCLK * MFBC / (MFFC * MOC)
OSCCLK = 27 MHz
AMD Geode™ SC3200 Processor Data Book
103
Revision 5.1
General Configuration Block
Table 4-8. Clock Generator Configuration (Continued)
Bit
Description
Offset 1Eh-1Fh
Core Clock Frequency Control Register - CCFC (R/W)
This register controls the configuration of the core clock multiplier and the reference clocks.
15:14
Reserved.
13
Reserved. Must be set to 0.
12
Reserved. Must be set to 0.
11:10
9:8
Reset Value: Strapped Value
Reserved.
FPCICK (Internal Fast-PCI Clock). (Read Only) Reflects the internal Fast-PCI clock and is the input to the GX1 module
that is used to generate the core clock. These bits reflect the value of strap pins CLKSEL[1:0].
00: 33.3 MHz
01: 48 MHz
10: 66.7 MHz
11: 33.3 MHz
7:4
Reserved.
3:0
MVAL (Multiplier Value). This 4-bit value controls the multiplier in ADL. The value is set according to the Maximum Clock
Multiplier bits of the MCCM register (Offset 10h). The multiplier value should never be written with a multiplier which is different from the multiplier indicated in the MCCM register.
0100: Multiply by 4
0101: Multiply by 5
0110: Multiply by 6
0111: Multiply by 7
1000: Multiply by 8
1001: Multiply by 9
1010: Multiply by 10
Other: Reserved
104
AMD Geode™ SC3200 Processor Data Book
SuperI/O Module
Revision 5.1
5
5.0SuperI/O Module
The SuperI/O (SIO) module is a PC98 and ACPI compliant
SIO that offers a single-cell solution to the most commonly
used ISA peripherals.
The SIO module incorporates: two Serial Ports, an Infrared
Communication Port that supports FIR, MIR, HP-SIR,
Sharp-IR, and Consumer Electronics-IR, a full IEEE 1284
Parallel Port, two ACCESS.bus Interface (ACB) ports, System Wakeup Control (SWC), and a Real-Time Clock (RTC)
that provides RTC timekeeping.
Outstanding Features
• Full compatibility with ACPI Revision 1.0 requirements.
• System Wakeup Control powered by VSB, generates
power-up request and a PME (power management
event) in response to SDATA_IN2 (an audio codec),
IRRX1 (a pre-programmed CEIR), or a RI2# (serial port
ring indicate) event.
• Advanced RTC, Y2K compliant.
Serial
Interface
Serial
Interface
Infrared /Serial
Interface
Serial Port 1
Serial Port 2
IR Comunication
Port/Serial Port 3
System Wakeup
Control
Wakeup PWUREQ
Events
ACCESS.bus 1
AB1C
AB1D
VBAT
Real-Time Clock
ACCESS.bus 2
AB2C
AB2D
ISA
Interface
VSB
Host Interface
IEEE 1284
Parallel Port
Parallel Port
Interface
Figure 5-1. SIO Block Diagram
AMD Geode™ SC3200 Processor Data Book
105
Revision 5.1
5.1
SuperI/O Module
Features
PC98 and ACPI Compliant
System Wakeup Control (SWC)
• PnP Configuration Register structure
• Power-up request upon detection of RI2#, CEIR, or
SDATA_IN2 activity:
— Optional routing of power-up request on IRQ line
• Flexible resource allocation for all logical devices:
— Relocatable base address
— 9 Parallel IRQ routing options
— 3 optional 8-bit DMA channels (where applicable)
• Pre-programmed CEIR address in a pre-selected
standard (any NEC, RCA or RC-5)
Parallel Port
• Powered by VSB
• Software or hardware control
• Battery-backed wakeup setup
• Enhanced Parallel Port (EPP) compatible with version
EPP 1.9 and IEEE 1284 compliant
• Power-fail recovery support
• EPP support for version EPP 1.7 of the Xircom specification
Real-Time Clock
• A modifiable address that is referenced by a 16-bit
programmable register
• EPP support as mode 4 of the Extended Capabilities
Port (ECP)
• DS1287, MC146818 and PC87911 compatibility
• IEEE 1284 compliant ECP, including level 2
• 242 bytes of battery backed up CMOS RAM in two
banks
• Selection of internal pull-up or pull-down resistor for
Paper End (PE) pin
• Selective lock mechanisms for the CMOS RAM
• PCI bus utilization reduction by supporting a demand
DMA mode mechanism and a DMA fairness mechanism
• Battery backed up century calendar in days, day of the
week, date of month, months, years and century, with
automatic leap-year adjustment
• Protection circuit that prevents damage to the parallel
port when a printer connected to it powers up or is operated at high voltages, even if the device is in powerdown
• Battery backed-up time of day in seconds, minutes and
hours that allows a 12 or 24 hour format and adjustments for daylight savings time
• Output buffers that can sink and source 14 mA
Serial Port 1
• 16550A compatible (SIN1, SOUT1, DTR1#/BOUT1
signals only)
Serial Port 2
• 16550A compatible
Serial Port 3 / Infrared (IR) Communication Port
• BCD or binary format for time keeping
• Three different maskable interrupt flags:
— Periodic interrupts - At intervals from 122 ms to 500
ms
— Time-of-Month alarm - At intervals from once per
second to once per month
— Update Ended Interrupt - Once per second upon
completion of update
• Separate battery pin, 3.0V operation that includes an
internal UL protection resistor
• Serial Port 3
— SIN and SOUT signals only
— Data rate of up to 1.5-Mbps
— Software compatible with the 16550A and the 16450
— Shadow register support for write-only bit monitoring
— DMA support
• 7 µA typical power consumption during power down
• IR Communication Port
— IrDA 1.1 and 1.0 compatible
— Data rate of up to 115.2 Kbps (HP-SIR)
— Data rate of 1.152 Mbps (MIR)
— Data rate of 4.0 Mbps (FIR)
— Selectable internal or external modulation/demodulation (ASK-IR and DASK-IR options of SHARP-IR)
— Consumer-IR (TV-Remote) mode
— Consumer Remote Control supports RC-5, RC-6,
NEC, RCA and RECS 80
— DMA support
• 48 MHz clock input
106
• Double-buffer time registers
• Y2K Compliant
Clock Sources
• On-chip low frequency clock generator for wakeup
• 32.768 KHz crystal with an internal frequency multiplier
to generate all required internal frequencies
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
Module Architecture
The SIO module comprises a collection of generic functional blocks. Each functional block is described in detail
later in this chapter. The beginning of this chapter
describes the SIO structure and provides all device specific
information, including special implementation of generic
blocks, system interface and device configuration.
The SIO module is based on eight logical devices, the host
interface, and a central configuration register set, all built
around a central, internal 8-bit bus.
The source of the device internal clocks is the 48 MHz
clock signal or through the 32.768 KHz crystal with an
internal frequency multiplier. RTC operates on a 32 KHz
clock.
Infrared
Communication
Port/Serial Port 3
Parallel
Port
AB1C
AB2C
Configuration
and Control
Registers
ACCESS.
bus 2
Internal
Signal
RI2#
Control Signals
Internal Bus
VBAT
VSB
X2C
X1C/X1
ALARM
SOUT1
Serial
Port 2
SIN2
SOUT2
RTS2#
DTR2#/BOUT2
CTS2
RI2#
DCD2#
DSR2#
Internal
Host
Interface
TC
DACK0-3
DRQ0-3
IRQ1-12,14-15
IOCHRDY
ZWS#
IOWR#
IORD#
AEN
System
Wakeup
Real-Time Clock (RTC)
SDATA_IN2
AB2D
Serial
Port 1
DTR#/BOUT1
ACCESS.
bus 1
AB1D
SIN1
Internal
Signals
CONFIG
CLKIN
MR
D[7:0]
A[15:0]
ACK#
AFD#/DSTRB#
BUSY/WAIT#
ERR#
INIT#
PD[7:0]
PE
SLCT
SLIN#/ASTRB#
STB#/WRITE#
IRRX1/SIN3
IRTX/SOUT3
The host interface serves as a bridge between the external
ISA interface and the internal bus. It supports 8-bit I/O
read, 8-bit I/O write and 8-bit DMA transactions, as defined
in Personal Computer Bus Standard P996.
The central configuration register set supports ACPI compliant PnP configuration. The configuration registers are
structured as a subset of the Plug and Play Standard Registers, defined in Appendix A of the Plug and Play ISA
Specification Version 1.0a by Intel and Microsoft®. All system resources assigned to the functional blocks (I/O
address space, DMA channels and IRQ lines) are configured in, and managed by, the central configuration register
set. In addition, some function-specific parameters are configurable through this unit and distributed to the functional
blocks through special control signals.
PWUREQ
5.2
Internal Signals
Figure 5-2. Detailed SIO Block Diagram
AMD Geode™ SC3200 Processor Data Book
107
Revision 5.1
5.3
SuperI/O Module
Configuration Structure / Access
This section describes the structure of the configuration
register file, and the method of accessing the configuration
registers.
5.3.1
Index-Data Register Pair
The SIO configuration access is performed via an IndexData register pair, using only two system I/O byte locations.
The base address of this register pair is determined
according to the state of the IO_SIOCFG_IN bit field of the
Core Logic module (F5BAR0+I/O Offset 00h[26:25]). Table
5-1 shows the selected base addresses as a function of the
IO_SIOCFG_IN bit field.
Table 5-1. SIO Configuration Options
Table 5-2. LDN Assignments
LDN
Functional Block
Reference
00h
Real-Time Clock (RTC)
Page 114
01h
System Wakeup Control (SWC)
Page 116
02h
Infrared Communication Port
(IRCP) or Serial Port 3 (SP3)
Page 117
03h
Serial Port 1 (SP1)
Page 118
05h
ACCESS.bus 1 (ACB1)
Page 119
06h
ACCESS.bus 2 (ACB2)
07h
Parallel Port (PP)
Page 120
08h
Serial Port 2 (SP2)
Page 118
I/O Address
IO_SIOCFG_IN
Settings
Index
Register
Data
Register
00
-
-
SIO disabled
01
-
-
Configuration
access disabled
10
002Eh
002Fh
Base address 1
selected
11
015Ch
015Dh
Base address 2
selected
Description
The Index Register is an 8-bit R/W register located at the
selected base address (Base+0). It is used as a pointer to
the configuration register file, and holds the index of the
configuration register that is currently accessible via the
Data Register. Reading the Index Register returns the last
value written to it (or the default of 00h after reset).
The Data Register is an 8-bit virtual register, used as a
data path to any configuration register. Accessing the data
register results with physically accessing the configuration
register that is currently pointed by the Index Register.
5.3.2
Banked Logical Device Registers
Each functional block is associated with a Logical Device
Number (LDN). The configuration registers are grouped
into banks, where each bank holds the standard configuration registers of the corresponding logical device. Table 5-2
shows the LDNs of the device functional blocks.
Figure 5-3 shows the structure of the standard PnP configuration register file. The SIO Control And Configuration
registers are not banked and are accessed by the IndexData register pair only (as described above). However, the
Logical Device Control and Configuration registers are
duplicated over eight banks for eight logical devices. Therefore, accessing a specific register in a specific bank is performed by two-dimensional indexing, where the LDN
register selects the bank (or logical device), and the Index
register selects the register within the bank. Accessing the
Data register while the Index register holds a value of 30h
or higher results in a physical access to the Logical Device
Configuration registers currently pointed to by the Index
register, within the logical device bank currently selected by
the LDN register.
07h
Logical Device Number Register
20h
2Fh
SIO Configuration Registers
30h
Logical Device Control Register
60h
63h
70h
71h
74h
75h
F0h
FEh
Standard Logical Device
Standard Registers
Special (Vendor-defined)
Logical Device
Configuration Registers
Bank
Select
Banks
(One per Logical Device)
Figure 5-3. Structure of the Standard
Configuration Register File
108
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
Write accesses to unimplemented registers (i.e., accessing
the Data register while the Index register points to a nonexisting register or the LDN is 07h or higher than 08h), are
ignored and a read returns 00h on all addresses except for
74h and 75h (DMA configuration registers) which returns
04h (indicating no DMA channel is active). The configuration registers are accessible immediately after reset.
5.3.3
Default Configuration Setup
The device has four reset types:
Software Reset
This reset is generated by bit 1 of the SIOCF1 register,
which resets all logical devices. A software reset also
resets most bits in the SIO Configuration and Control registers (see Section 5.4.1 on page 113 for the bits not
affected). This reset does not affect register bits that are
locked for write access.
Hardware Reset
This reset is activated by the system reset signal. This
resets all logical devices, with the exception of the RTC and
the SWC, and all SIO Configuration and Control registers,
with the exception of the SIOCF2 register. It also resets all
SuperI/O control and configuration registers, except for
those that are battery-backed.
VPP Power-Up Reset
This reset is activated when either VSB or VBAT is powered
on after both have been off. VPP is an internal voltage
which is a combination of VSB and VBAT. VPP is taken from
VSB if VSB is greater than the minimum (Min) value defined
in Section 9.1.4 "Operating Conditions" on page 370; otherwise, VBAT is used as the VPP source. This reset resets
all registers whose values are retained by VPP.
VSB Power-Up Reset
This is an internally generated reset that resets the SWC,
excluding those SWC registers whose values are retained
by VPP. This reset is activated after VSB is powered up.
The SIO module wakes up with the default setup, as follows:
• When a hardware reset occurs:
— The configuration base address is 2Eh, 15Ch or
None, according to the IO_SIOCFG_IN bit values, as
shown in Table 5-1 on page 108.
— All Logical devices are disabled, with the exception of
the RTC and the SWC, which remains functional but
whose registers cannot be accessed.
• When either a hardware or a software reset occurs:
— The legacy devices are assigned with their legacy
system resource allocation.
— The AMD proprietary functions are not assigned with
any default resources and the default values of their
base addresses are all 00h.
5.3.4
Address Decoding
A full 16-bit address decoding is applied when accessing
the configuration I/O space, as well as the registers of the
functional blocks. However, the number of configurable bits in
the base address registers vary for each device.
The lower 1, 2, 3 or 4 address bits are decoded within the
functional block to determine the offset of the accessed
register, within the device’s I/O range of 2, 4, 8 or 16 bytes,
respectively. The rest of the bits are matched with the base
address register to decode the entire I/O range allocated to
the device. Therefore the lower bits of the base address
register are forced to 0 (RO), and the base address is
forced to be 2, 4, 8 or 16 byte aligned, according to the size
of the I/O range.
The base address of the RTC, Serial Port 1, Serial Port 2,
and the Infrared Communication Port are limited to the I/O
address range of 00h to 7Fxh only (bits [15:11] are forced
to 0). The Parallel Port base address is limited to the I/O
address range of 00h to 3F8h. The addresses of the nonlegacy devices are configurable within the full 16-bit
address range (up to FFFxh).
In some special cases, other address bits are used for
internal decoding (such as 10 in the Parallel Port). For
more details, please see the detailed description of the
base address register for each specific logical device.
AMD Geode™ SC3200 Processor Data Book
109
Revision 5.1
5.4
SuperI/O Module
Standard Configuration Registers
As illustrated in Figure 5-4, the Standard Configuration registers are broadly divided into two categories: SIO Control
and Configuration registers and Logical Device Control and
Configuration registers (one per logical device, some are
optional).
SIO Control and Configuration Registers
The only PnP control register in the SIO module is the Logical Device Number register at Index 07h. All other standard PnP control registers are associated with PnP
protocol for ISA add-in cards, and are not supported by the
SIO module.
The SIO Configuration registers at Index 20h-27h are
mainly used for part identification. (See Section 5.4.1 "SIO
Control and Configuration Registers" on page 113 for further details.)
Logical Device Control and Configuration Registers
A subset of these registers is implemented for each logical
device. (See Table 5-2 on page 108 for LDN assignment
and Section 5.4.2 "Logical Device Control and Configuration" on page 114 for register details.)
Logical Device Control Register (Index 30h): The only
implemented Logical Device Control register is the Activate
register at Index 30. Bit 0 of the Activate register and bit 0
of the SIO Configuration 1 register (Global Device Enable
bit) control the activation of the associated function block
Index
SIO Control and
Configuration Registers
Logical Device Control and
Configuration Registers one per logical device
(some are optional)
(except for the RTC and the SWC). Activation of the block
enables access to the block’s registers, and attaches its
system resources, which are unused as long as the block is
not activated. Activation of the block may also result in
other effects (e.g., clock enable and active signaling), for
certain functions.
Standard Logical Device Configuration Registers
(Index 60h-75h): These registers are used to manage the
resource allocation to the functional blocks. The I/O port
base address descriptor 0 is a pair of registers at Index
60h-61h, holding the (first or only) 16-bit base address for
the register set of the functional block. An optional second
base-address (descriptor 1) at Index 62h-63h is used for
devices with more than one continuous register set. Interrupt Number Select (Index 70h) and Interrupt Type Select
(Index 71h) allocate an IRQ line to the block and control its
type. DMA Channel Select 0 (Index 74h) allocates a DMA
channel to the block, where applicable. DMA Channel
Select 1 (Index 75h) allocates a second DMA channel,
where applicable.
Special Logical Device Configuration Registers (F0hF3h): The vendor-defined registers, starting at Index F0h
are used to control function-specific parameters such as
operation modes, power saving modes, pin TRI-STATE,
clock rate selection, and non-standard extensions to
generic functions.
Register Name
07h
Logical Device Number
20h
SIO ID
21h
SIO Configuration 1
22h
SIO Configuration 2
27h
SIO Revision ID
2Eh
Reserved exclusively for AMD use
30h
Logical Device Control (Activate)
60h
I/O Port Base Address Descriptor 0 Bits [15:8]
61h
I/O Port Base Address Descriptor 0 Bits [7:0]
62h
I/O Port Base Address Descriptor 1 Bits [15:8]
63h
I/O Port Base Address Descriptor 1 Bits [7:0]
70h
Interrupt Number Select
71h
Interrupt Type Select
74h
DMA Channel Select 0
75h
DMA Channel Select 1
F0h
Device Specific Logical Device Configuration 1
F1h
Device Specific Logical Device Configuration 2
F2h
Device Specific Logical Device Configuration 3
F3h
Device Specific Logical Device Configuration 4
Figure 5-4. Standard Configuration Registers Map
110
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
Table 5-3 provides the bit definitions for the Standard Configuration registers.
• All reserved bits return 0 on reads, except where noted
otherwise. They must not be modified as such modification may cause unpredictable results. Use read-modify-
write to prevent the values of reserved bits from being
changed during write.
• Write only registers should not use read-modify-write
during updates.
Table 5-3. Standard Configuration Registers
Bit
Description
Index 07h
Logical Device Number (R/W)
This register selects the current logical device. See Table 5-2 for valid numbers. All other values are reserved.
7:0
Logical Device number.
Index 20h-2Fh
SIO Configuration (R/W)
SIO configuration and ID registers. See Section 5.4.1 "SIO Control and Configuration Registers" on page 113 for register/bit details.
Index 30h
7:1
0
Activate (R/W)
Reserved.
Logical Device Activation Control.
0:
Disable
1:
Enable
Index 60h
7:0
I/O Port Base Address Bits [15:8] Descriptor 0 (R/W)
Descriptor 0 A[15:8]. Selects I/O lower limit address bits [15:8] for I/O Descriptor 0.
Index 61h
7:0
I/O Port Base Address Bits [7:0] Descriptor 0 (R/W)
Descriptor 0 A[7:0]. Selects I/O lower limit address bits [7:0] for I/O Descriptor 0.
Index 62h
7:0
I/O Port Base Address Bits [15:8] Descriptor 1 (R/W)
Descriptor 1 A[15:8]. Selects I/O lower limit address bits [15:8] for I/O Descriptor 1.
Index 63h
7:0
I/O Port Base Address Bits [7:0] Descriptor 1 (R/W)
Descriptor 1 A[7:0]. Selects I/O lower limit address bits [7:0] for I/O Descriptor 1.
Index 70h
Interrupt Number (R/W)
7:4
Reserved.
3:0
Interrupt Number. These bits select the interrupt number. A value of 1 selects IRQ1, a value of 2 selects IRQ2, etc. (up to
IRQ12).
Note: IRQ0 is not a valid interrupt selection.
Index 71h
Interrupt Request Type Select (R/W)
Selects the type and level of the interrupt request number selected in the previous register.
7:2
1
Reserved.
Interrupt Level Requested. Level of interrupt request selected in previous register.
0:
Low polarity.
1:
High polarity.
This bit must be set to 1 (high polarity), except for IRQ8#, that must be low polarity.
0
Interrupt Type Requested. Type of interrupt request selected in previous register.
0:
Edge.
1:
Level.
Index 74h
DMA Channel Select 0 (R/W)
Selects selected DMA channel for DMA 0 of the logical device (0 - the first DMA channel in case of using more than one DMA channel).
7:3
Reserved.
2:0
DMA 0 Channel Select. This bit field selects the DMA channel for DMA 0.
The valid choices are 0-3, where a value of 0 selects DMA channel 0, 1 selects channel 1, etc.
A value of 4 indicates that no DMA channel is active.
Values 5-7 are reserved.
AMD Geode™ SC3200 Processor Data Book
111
Revision 5.1
SuperI/O Module
Table 5-3. Standard Configuration Registers (Continued)
Bit
Description
Index 75h
DMA Channel Select 1 (R/W)
Indicates selected DMA channel for DMA 1 of the logical device (1 - the second DMA channel in case of using more than one DMA
channel).
7:3
2:0
Reserved.
DMA 1 Channel Select: This bit field selects the DMA channel for DMA 1.
The valid choices are 0-3, where a value of 0 selects DMA channel 0, 1 selects channel 1, etc.
A value of 4 indicates that no DMA channel is active.
Values 5-7 are reserved.
Index F0h-FEh
Logical Device Configuration (R/W)
Special (vendor-defined) configuration options.
112
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
5.4.1
SIO Control and Configuration Registers
Table 5-4 lists the SIO Control and Configuration registers and Table 5-5 provides their bit formats.
Table 5-4. SIO Control and Configuration Register Map
Index
Type
20h
RO
21h
Name
Power Rail
Reset Value
SID. SIO ID
VCORE
F5h
R/W
SIOCF1. SIO Configuration 1
VCORE
01h
22h
R/W
SIOCF2. SIO Configuration 2
VPP
02h
27h
RO
SRID. SIO Revision ID
VCORE
01h
2Eh
---
RSVD. Reserved exclusively for AMD use.
---
---
Table 5-5. SIO Control and Configuration Registers
Bit
Description
Index 20h
7:0
SIO ID Register - SID (RO)
Index 21h
7:6
5
Reset Value: F5h
Chip ID. Contains the identity number of the module. The SIO module is identified by the value F5h.
SIO Configuration 1 Register - SIOCF1 (RW)
Reset Value: 01h
General Purpose Scratch. When bit 5 is set to 1, these bits are RO. After reset, these bits can be read or write. Once
changed to RO, the bits can be changed back to R/W only by a hardware reset.
Lock Scratch. This bit controls bits 7 and 6 of this register. Once this bit is set to 1 by software, it can be cleared to 0 only
by a hardware reset.
0: Bits 7 and 6 of this register are R/W bits. (Default)
1: Bits 7 and 6 of this register are RO bits.
4:2
1
Reserved.
SW Reset. Read always returns 0.
0: Ignored. (Default)
1: Resets all devices that are reset by MR (with the exception of the lock bits) and the registers of the SWC.
0
Global Device Enable. This bit controls the function enable of all the logical devices in the SIO module, except the SWC
and the RTC. It allows them to be disabled simultaneously by writing to a single bit.
0: All logical devices in the SIO module are disabled, except the SWC and the RTC.
1: Each logical device is enabled according to its Activate register at Index 30h. (Default)
Index 22h
SIO Configuration 2 Register - SIOCF2 (R/W)
Note: This register is reset only when VPP is first applied.
7
Reserved.
6:4
General Purpose Scratch. Battery-backed.
3:2
Reserved.
1
Reserved.
0
Reserved. (RO)
Index 27h
7:0
Reset Value: 02h
SIO Revision ID Register - SRID (RO)
Reset Value: 01h
SIO Revision ID. (RO) This RO register contains the identity number of the chip revision. SRID is incremented on each revision.
AMD Geode™ SC3200 Processor Data Book
113
Revision 5.1
5.4.2
Logical Device Control and
Configuration
As described in Section 5.3.2 "Banked Logical Device Registers" on page 108, each functional block is associated
with a Logical Device Number (LDN). This section provides
the register descriptions for each LDN.
SuperI/O Module
5.4.2.1 LDN 00h - Real-Time Clock
Table 5-6 lists the registers which are relevant to configuration of the Real-Time Clock (RTC). Only the last registers
(F0h-F3h) are described here (Table 5-7). See Table 5-3
"Standard Configuration Registers" on page 111 for
descriptions of the other registers.
The register descriptions in this subsection use the following abbreviations for Type:
• R/W
• R
= Read/Write
= Read from a specific address returns the
value of a specific register. Write to the
same address is to a different register.
• W
= Write
• RO
= Read Only
• R/W1C = Read/Write 1 to Clear. Writing 1 to a bit
clears it to 0. Writing 0 has no effect.
Table 5-6. Relevant RTC Configuration Registers
Reset
Value
Index
Type
Configuration Register or Action
30h
R/W
Activate. When bit 0 is cleared, the registers of this logical device are not accessible.1
00h
60h
R/W
Standard Base Address MSB register. Bits [7:3] (for A[15:11]) are RO, 00000b.
00h
61h
R/W
Standard Base Address LSB register. Bit 0 (for A0) is RO, 0b.
70h
62h
R/W
Extended Base Address MSB register. Bits [7:3] (for A[15:11]) are RO, 00000b.
00h
63h
R/W
Extended Base Address LSB register. Bit 0 (for A0) is RO, 0b.
72h
70h
R/W
Interrupt Number.
08h
71h
R/W
Interrupt Type. Bit 1 is R/W; other bits are RO.
00h
74h
RO
Report no DMA assignment.
04h
75h
RO
Report no DMA assignment.
04h
F0h
R/W
RAM Lock register (RLR).
00h
F1h
R/W
Date of Month Alarm Offset register (DOMAO). Sets index of Date of Month Alarm
register in the standard base address.
00h
F2h
R/W
Month Alarm Offset register (MONAO). Sets index of Month Alarm register in the
standard base address.
00h
F3h
R/W
Century Offset register (CENO). Sets index of Century register in the standard base
address.
00h
1.
114
The logical device registers are maintained, and all RTC mechanisms are functional.
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
Table 5-7. RTC Configuration Registers
Bit
Description
Index F0h
RAM Lock Register - RLR (R/W)
When any non-reserved bit in this register is set to 1, it can be cleared only by hardware reset.
7
Block Standard RAM.
0: No effect on Standard RAM access. (Default)
1: Read and write to locations 38h-3Fh of the Standard RAM are blocked, writes ignored, and reads return FFh.
6
Block RAM Write.
0: No effect on RAM access. (Default)
1: Writes to RAM (Standard and Extended) are ignored.
5
Block Extended RAM Write. This bit controls writes to bytes 00h-1Fh of the Extended RAM.
0: No effect on the Extended RAM access. (Default)
1: Writes to bytes 00h-1Fh of the Extended RAM are ignored.
4
Block Extended RAM Read. This bit controls read from bytes 00h-1Fh of the Extended RAM.
0: No effect on Extended RAM access. (Default)
1: Reads to bytes 00h-1Fh of the Extended RAM are ignored.
3
Block Extended RAM. This bit controls access to the Extended RAM 128 bytes.
0: No effect on Extended RAM access. (Default)
1: Read and write to the Extended RAM are blocked: writes are ignored and reads return FFh.
2:0
Reserved.
Index F1h
7
6:0
Date Of Month Alarm Register Offset Register - DOMAO (R/W)
Reserved.
Date of Month Alarm Register Offset Value.
Index F2h
7
6:0
Month Alarm Register Offset Register - MANAO (R/W)
Reserved.
Month Alarm Register Offset Value.
Index F3h
7
6:0
Century Register Offset Register - CENO (R/W)
Reserved.
Century Register Offset Value.
AMD Geode™ SC3200 Processor Data Book
115
Revision 5.1
SuperI/O Module
5.4.2.2 LDN 01h - System Wakeup Control
Table 5-8 lists registers that are relevant to the configuration of System Wakeup Control (SWC). These registers are
described earlier in Table 5-3 "Standard Configuration
Registers" on page 111.
Table 5-8. Relevant SWC Registers
Reset
Value
Index
Type
Configuration Register or Action
30h
R/W
Activate. When bit 0 is cleared, the registers of this logical device are not accessible.1
00h
60h
R/W
Base Address MSB register.
00h
61h
R/W
Base Address LSB register. Bits [3:0] (for A[3:0]) are RO, 0000b.
00h
70h
R/W
Interrupt Number. (For routing the internal PWUREQ signal.)
00h
71h
R/W
Interrupt Type. Bit 1 is R/W. Other bits are RO.
03h
74h
RO
Report no DMA assignment.
04h
75h
RO
Report no DMA assignment.
04h
1.
116
The logical device registers are maintained, and all wakeup detection mechanisms are functional.
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
5.4.2.3
LDN 02h - Infrared Communication Port or
Serial Port 3
Table 5-9 lists the configuration registers which affect the
Infrared Communication Port or Serial Port 3 (IRCP/SP3).
Only the last register (F0h) is described here (Table 5-10).
See Table 5-3 "Standard Configuration Registers" on page
111 for descriptions of the other registers listed.
Table 5-9. Relevant IRCP/SP3 Registers
Reset
Value
Index
Type
Configuration Register or Action
30h
R/W
Activate. See also bit 0 of the SIOCF1 register.
00h
60h
R/W
Base Address MSB register. Bits [7:3] (for A[15:11]) are RO, 00000b.
03h
61h
R/W
Base Address LSB register. Bit [2:0] (for A[2:0]) are RO, 000b.
E8h
70h
R/W
Interrupt Number.
00h
71h
R/W
Interrupt Type. Bit 1 is R/W; other bits are RO.
03h
74h
R/W
DMA Channel Select 0 (RX_DMA).
04h
75h
R/W
DMA Channel Select 1 (TX_DMA).
04h
F0h
R/W
Infrared Communication Port/Serial Port 3 Configuration register.
02h
Table 5-10. IRCP/SP3 Configuration Register
Bit
Description
Index F0h
7
Infrared Communication Port/Serial Port 3 Configuration Register (R/W)
Reset Value: 02h
Bank Select Enable. Enables bank switching.
0: All attempts to access the extended registers are ignored. (Default)
1: Enables bank switching.
6:3
2
Reserved.
Busy Indicator. (RO) This bit can be used by power management software to decide when to power-down the device.
0: No transfer in progress. (Default)
1: Transfer in progress.
1
Power Mode Control. When the logical device is active in:
0: Low power mode - Clock disabled. The output signals are set to their default states. Registers are maintained. (Unlike
Active bit in Index 30h that also prevents access to device registers.)
1: Normal power mode - Clock enabled. The device is functional when the logical device is active. (Default)
0
TRI-STATE Control. When enabled and the device is inactive, the logical device output pins are in TRI-STATE. One exception is the IRTX/SOUT3 pin, which is driven to 0 when the Infrared Communication Port or Serial Port 3 is inactive and is not
affected by this bit.
0: Disabled. (Default)
1: Enabled (when the device is inactive).
AMD Geode™ SC3200 Processor Data Book
117
Revision 5.1
SuperI/O Module
5.4.2.4 LDN 03h and 08h - Serial Ports 1 and 2
Serial Ports 1 and 2 are identical, except for their reset values.
Serial Port 1 is designated as LDN 03h and Serial Port 2 as
LDN 08h. Table 5-11 lists the configuration registers which
affect Serial Ports 1 and 2. Only the last register (F0h) is
described here (Table 5-12). See Table 5-3 "Standard
Configuration Registers" on page 111 for descriptions of
the others.
Table 5-11. Relevant Serial Ports 1 and 2 Registers
Reset Value
Index
Type
Configuration Register or Action
Port 1
Port 2
30h
R/W
Activate. See also bit 0 of the SIOCF1 register.
00h
00h
60h
R/W
Base Address MSB register. Bits [7:3] (for A[15:11]) are RO, 00000b.
03h
02h
61h
R/W
Base Address LSB register. Bit [2:0] (for A[2:0]) are RO, 000b.
F8h
F8h
70h
R/W
Interrupt Number.
04h
03h
71h
R/W
Interrupt Type. Bit 1 is R/W; other bits are RO.
03h
03h
74h
RO
Report no DMA assignment.
04h
04h
75h
RO
Report no DMA assignment.
04h
04h
F0h
R/W
Serial Ports 1 and 2 Configuration register.
02h
02h
Table 5-12. Serial Ports 1 and 2 Configuration Register
Bit
Description
Index F0h
7
Serial Ports 1 and 2 Configuration Register (R/W)
Reset Value: 02h
Bank Select Enable. Enables bank switching for Serial Ports 1 and 2.
0: Disabled. (Default)
1: Enabled.
6:3
2
Reserved.
Busy Indicator. (RO) This bit can be used by power management software to decide when to power-down Serial Ports 1
and 2 logical devices.
0: No transfer in progress. (Default)
1: Transfer in progress.
1
Power Mode Control. When the logical device is active in:
0: Low power mode - Serial Ports 1 and 2 Clock disabled. The output signals are set to their default states. Registers are
maintained. (Unlike Active bit in Index 30h that also prevents access to Serial Ports 1 or 2 registers.)
1: Normal power mode - Serial Ports 1 and 2 clock enabled. Serial Ports 1 and 2 are functional when the respective logical
devices are active. (Default)
0
TRI-STATE Control. This bit controls the TRI-STATE status of the device output pins when it is inactive (disabled).
0: Disabled. (Default)
1: Enabled when device inactive.
118
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
5.4.2.5 LDN 05h and 06h - ACCESS.bus Ports 1 and 2
ACCESS.bus ports 1 and 2 (ACB1 and ACB2) are identical. Each ACB is a two-wire synchronous serial interface
compatible with the ACCESS.bus physical layer. ACB1 and
ACB2 use a 24 MHz internal clock. Six runtime registers for
each ACCESS.bus are described in Section 5.7
"ACCESS.bus Interface" on page 137.
ACB1 is designated as LDN 05h and ACB2 as LDN 06h.
Table 5-13 lists the configuration registers which affect the
ACCESS.bus ports. Only the last register (F0h) is
described here (Table 5-14). See Table 5-3 "Standard
Configuration Registers" on page 111 for descriptions of
the others.
Table 5-13. Relevant ACB1 and ACB2 Registers
Reset
Value
Index
Type
Configuration Register or Action
30h
R/W
Activate. See also bit 0 of the SIOCF1 register
00h
60h
R/W
Base Address MSB register.
00h
61h
R/W
Base Address LSB register. Bits [2:0] (for A[2:0]) are RO, 000b.
00h
70h
R/W
Interrupt Number.
00h
71h
R/W
Interrupt Type. Bit 1 is R/W. Other bits are RO.
03h
74h
RO
Report no DMA assignment.
04h
75h
RO
Report no DMA assignment.
04h
F0h
R/W
ACB1 and ACB2 Configuration register.
00h
Table 5-14. ACB1 and ACB2 Configuration Register
Bit
Description
Index F0h
ACB1 and ACB2 Configuration Register (R/W)
This register is reset by hardware to 00h.
7:3
2
Reserved.
Internal Pull-Up Enable.
0: No internal pull-up resistors on AB1C/AB2C and AB1D/AB2D. (Default)
1: Internal pull-up resistors on AB1C/AB2C and AB1D/AB2D.
1:0
Reserved.
AMD Geode™ SC3200 Processor Data Book
119
Revision 5.1
SuperI/O Module
5.4.2.6 LDN 07h - Parallel Port
The Parallel Port supports all IEEE 1284 standard communication modes: Compatibility (known also as Standard or
SPP), Bidirectional (known also as PS/2), FIFO, EPP
(known also as Mode 4) and ECP (with an optional
Extended ECP mode).
The Parallel Port includes two groups of runtime registers,
as follows:
• A group of 21 registers at first level offset, sharing 14
entries. Three of these registers (at Offset 403h, 404h,
and 405h) are used only in the Extended ECP mode.
• A group of four registers, used only in the Extended ECP
mode, accessed by a second level offset.
The desired mode is selected by the ECR runtime register
(Offset 402h). The selected mode determines which runtime registers are used and which address bits are used for
the base address. (See Section 5.8.1 on page 145 for further details regarding the runtime registers.)
Table 5-15 lists the configuration registers which affect the
Parallel Port. Only the last register (F0h) is described here
(Table 5-16). See Table 5-3 "Standard Configuration Registers" on page 111 for descriptions of the others.
Table 5-15. Relevant Parallel Port Registers
Reset
Value
Index
Type
Configuration Register or Action
30h
R/W
Activate. See also bit 0 of the SIOCF1 register.
00h
60h
R/W
Base Address MSB register. Bits [7:3] (for A[15:11]) are RO, 00000b. Bit 2 (for A10)
should be 0b.
02h
61h
R/W
Base Address LSB register. Bits 1 and 0 (A1 and A0) are RO, 00b. For ECP Mode 4
(EPP) or when using the Extended registers, bit 2 (A2) should also be 0b.
78h
70h
R/W
Interrupt Number.
07h
71h
R/W
Interrupt Type.
02h
Bits [7:2] are RO.
Bit 1 is R/W.
Bit 0 is RO. It reflects the interrupt type dictated by the Parallel Port operation mode.
This bit is set to 1 (level interrupt) in Extended Mode and cleared (edge interrupt) in all
other modes.
74h
R/W
DMA Channel Select.
04h
75h
RO
Report no second DMA assignment.
04h
F0h
R/W
Parallel Port Configuration register. (See Table 5-16.)
F2h
Table 5-16. Parallel Port Configuration Register
Bit
Description
Index F0h
This register is reset by hardware to F2h.
7:5
4
Parallel Port Configuration Register (R/W)
Reset Value: F2h
Reserved. Must be 11.
Extended Register Access.
0: Registers at base (address)+403h, base+404h and base+405h are not accessible (reads and writes are ignored).
1: Registers at base (address)+403h, base+404h and base+405h are accessible. This option supports run-time configuration within the Parallel Port address space.
3:2
1
Reserved.
Power Mode Control. When the logical device is active:
0: Parallel port clock disabled. ECP modes and EPP timeout are not functional when the logical device is active. Registers
are maintained.
1: Parallel port clock enabled. All operation modes are functional when the logical device is active. (Default)
0
TRI-STATE Control. When enabled and the device is inactive, the logical device output pins are in TRI-STATE.
0: Disable. (Default)
1: Enable.
120
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
5.5
Real-Time Clock (RTC)
The RTC provides timekeeping and calendar management
capabilities. The RTC uses a 32.768 KHz signal as the
basic clock for timekeeping. It also includes 242 bytes of
battery-backed RAM for general-purpose use.
The RTC provides the following functions:
5.5.2
RTC Clock Generation
The RTC uses a 32.768 KHz clock signal as the basic
clock for timekeeping. The 32.768 KHz clock can be supplied by the internal oscillator circuit, or by an external
oscillator (see Section 5.5.2.2 "External Oscillator" on page
122).
• Accurate timekeeping and calendar management
• Alarm at a predetermined time and/or date
• Three programmable interrupt sources
• Valid timekeeping during power-down, by utilizing
external battery backup
• 242 bytes of battery-backed RAM
• RAM lock schemes to protect its content
5.5.2.1 Internal Oscillator
The internal oscillator employs an external crystal connected to the on-chip amplifier. The on-chip amplifier is
accessible on the X32I input and X32O output. See Figure
5-5 for the recommended external circuit and Table 5-17
for a listing of the circuit components. The oscillator may be
disabled in certain conditions. See Section 5.5.2.8 "Oscillator Activity" on page 125 for more details.
• Internal oscillator circuit (the crystal itself is off-chip), or
external clock supply for the 32.768 KHz clock
CF
• PnP support:
— Relocatable Index and Data registers
— Module access enable/disable option
— Host interrupt enable/disable option
X32I
R1
• Additional low-power features such as:
— Automatic switching from battery to VSB
— Internal power monitoring on the VRT bit
— Oscillator disabling to save battery during storage
• Software compatible with the DS1287 and MC146818
5.5.1
To other
modules
Internal
External
X32O
VBAT
• A century counter
Bus Interface
B1
C1
R2
C2
Y
Battery
CF = 0.1 µF
Figure 5-5. Recommended Oscillator External
Circuitry
The RTC function is initially mapped to the default SuperI/O
locations at Indexes 70h to 73h (two Index/Data pairs).
These locations may be reassigned, in compliance with
Plug and Play requirements.
Table 5-17. Crystal Oscillator Circuit Components
Component
Parameters
Values
Tolerance
Crystal
Resonance Frequency
32.768 KHz Parallel mode
User-defined
Type
N-cut or XY-bar
Serial Resistance
40 KΩ
Max
Quality Factor, Q
35000
Min
Shunt Capacitance
2 pF
Max
Load Capacitance, CL
9-13 pF
Temperature Coefficient
User-defined
Resistor R1
Resistance
20 MΩ
5%
Resistor R2
Resistance
120 KΩ
5%
Capacitor C1
Capacitance
3 to 10 pF
5%
Capacitor C2
Capacitance
3 to 10 pF
5%
AMD Geode™ SC3200 Processor Data Book
121
Revision 5.1
External Elements
Choose C1 and C2 capacitors (see Figure 5-5 on page
121) to match the crystal’s load capacitance. The load
capacitance CL “seen” by crystal Y is comprised of C1 in
series with C2 and in parallel with the parasitic capacitance
of the circuit. The parasitic capacitance is caused by the
chip package, board layout and socket (if any), and can
vary from 0 to 10 pF. The rule of thumb in choosing these
capacitors is:
SuperI/O Module
The divider chain can be activated by setting normal operational mode (bits [6:4] of CRA = 01x or 100). The first
update occurs 500 ms after divider chain activation.
Bits [3:0] of CRA select one the of fifteen taps from the
divider chain to be used as a periodic interrupt. The periodic flag becomes active after half of the programmed
period has elapsed, following divider chain activation.
See Table 5-20 on page 127 for more details.
CL = (C1 * C2) / (C1 + C2) + CPARASITIC
Example:
Crystal CL = 10 pF, CPARASITIC = 8.2 pF
C1 = 3.6 pF, C2 = 3.6 pF
VBAT
To other
modules
Internal
CF
Oscillator Startup
The oscillator starts to generate 32.768 KHz pulses to the
RTC after about 100 ms from when VBAT is higher than
VBATMIN (2.4V) or VSB is higher than VSBMIN (3.0V). The
oscillation amplitude on the X32O pin stabilizes to its final
value (approximately 0.4V peak-to-peak around 0.7V DC)
in about 1 s.
C1 can be trimmed to achieve precisely 32.768 KHz. To
achieve a high time accuracy, use crystal and capacitors
with low tolerance and temperature coefficients.
5.5.2.2 External Oscillator
32.768 KHz can be applied from an external clock source,
as shown in Figure 5-6.
External
NC
R2
R1
3.3V square wave
OUT
POWER
32.768 KHz R1 = 30 KΩ
Clock Generator R2 = 30 KΩ
CF = 0.1 µF
CF
B1
Battery
Figure 5-6. External Oscillator Connections
Connections
Connect the clock to the X32I ball, leaving the oscillator
output, X32O, unconnected.
Divider Chain
1
2
Signal Parameters
The signal levels should conform to the voltage level
requirements for X32I, of square or sine wave of 0.0V to
VCORE amplitude. The signal should have a duty cycle of
approximately 50%. It should be sourced from a batterybacked source in order to oscillate during power-down.
This assures that the RTC delivers updated time/calendar
information.
5.5.2.3 Timing Generation
The timing generation function divides the 32.768 KHz
clock by 215 to derive a 1 Hz signal, which serves as the
input for the seconds counter. This is performed by a
divider chain composed of 15 divide-by-two latches, as
shown in Figure 5-7.
X32O
CLKIN
(X32I)
2
2
3
2
13 14 15
2 2 2
1 Hz
Reset
DV2 DV1 DV0
6
5
4
CRA Register
32.768 KHz
To other
modules
X32I
Oscillator
Enable
X32O
Figure 5-7. Divider Chain Control
Bits [6:4] (DV[2:0]) of the CRA Register control the following functions:
• Normal operation of the divider chain (counting).
• Divider chain reset to 0.
• Oscillator activity when only VBAT power is present
(backup state).
122
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
5.5.2.4
Timekeeping
Data Format
Time is kept in BCD or binary format, as determined by bit
2 (DM) of Control Register B (CRB), and in either 12 or 24hour format, as determined by bit 1 of this register.
Note:
Method 2
1) Access the RTC registers after detection of an Update
Ended interrupt. This implies that an update has just
been completed and 999 ms remain until the next
update.
2)
When changing the above formats, re-initialize all
the time registers.
— Poll bit 4 of CRC.
— Use the following interrupt routine:
– Set bit 4 of CRB.
– Wait for an interrupt from interrupt pin.
– Clear the IRQF flag of CRC before exiting the
interrupt routine.
Daylight Saving
Daylight saving time exceptions are handled automatically,
as described in Table 5-20 on page 127.
Leap Years
Leap year exceptions are handled automatically by the
internal calendar function. Every four years, February is
extended to 29 days.
Updating
The time and calendar registers are updated once per second regardless of bit 7 (SET) of CRB. Since the time and
calendar registers are updated serially, unpredictable
results may occur if they are accessed during the update.
Therefore, you must ensure that reading or writing to the
time storage locations does not coincide with a system
update of these locations. There are several methods to
avoid this contention.
Method 1
1) Set bit 7 of CRB to 1. This takes a “snapshot” of the
internal time registers and loads them into the user
copy registers. The user copy registers are seen when
accessing the RTC from outside, and are part of the
double buffering mechanism. You may keep this bit set
for up to 1 second, since the time/calendar chain continue to be updated once per second.
2)
3)
Read or write the required registers (since bit 1 is set,
you are accessing the user copy registers). If you perform a read operation, the information you read is correct from the time when bit 1 was set. If you perform a
write operation, you write only to the user copy registers.
Reset bit 1 to 0. During the transition, the user copy
registers update the internal registers, using the double buffering mechanism to ensure that the update is
performed between two time updates. This mechanism enables new time parameters to be loaded in the
RTC.
AMD Geode™ SC3200 Processor Data Book
To detect an Update Ended interrupt, you may either:
Method 3
Poll bit 7 of CRA. The update occurs 244 µs after this bit
goes high. Therefore, if a 0 is read, the time registers
remain stable for at least 244 µs.
Method 4
Use a periodic interrupt routine to determine if an update
cycle is in progress, as follows:
1)
Set the periodic interrupt to the desired period.
2)
Set bit 6 of CRB to enable the interrupt from periodic
interrupt.
3)
Wait for the periodic interrupt appearance. This indicates that the period represented by the following
expression remains until another update occurs:
[(Period of periodic interrupt / 2) + 244 µs]
5.5.2.5 Alarms
The timekeeping function can be set to generate an alarm
when the current time reaches a stored alarm time. After
each RTC time update (every 1 second), the seconds, minutes, hours, date of month and month counters are compared with their corresponding registers in the alarm
settings. If equal, bit 5 of CRC is set. If the Alarm Interrupt
Enable bit was previously set (CRB bit 5), interrupt request
pin is also active.
Any alarm register may be set to “Unconditional Match” by
setting bits [7:6] to 11. This combination, not used by any
BCD or binary time codes, results in a periodic alarm. The
rate of this periodic alarm is determined by the registers
that were set to “Unconditional Match”.
For example, if all but the seconds and minutes alarm registers are set to “Unconditional Match”, an interrupt is generated every hour at the specified minute and second. If all
but the seconds, minutes and hours alarm registers are set
to “Unconditional Match”, an interrupt is generated every
day at the specified hour, minute and second.
123
Revision 5.1
SuperI/O Module
5.5.2.6 Power Supply
The device is supplied from two supply voltages, as shown
in Figure 5-8:
• System standby power supply voltage, VSB
• Backup voltage, from low capacity Lithium battery
A standby voltage, VSB, from the external AC/DC power
supply powers the RTC under normal conditions.
Figure 5-9 represents a typical battery configuration. No
external diode is required to meet the UL standard, due to
the internal switch and internal serial resistor RUL.
External AC Power
ACPI Controller
ONCTL#
PC0
RTC
VSB
VBAT
VDIGITAL
VSB
VBAT
VSB
VBAT
To assure that the module uses power from VSB and not
from VBAT, the VSB voltage should be maintained above its
minimum, as detailed in Section 9.0 "Electrical Specifications" on page 369.
The actual voltage point where the module switches from
VBAT to VSB is lower than the minimum workable battery
voltage, but high enough to guarantee the correct functionality of the oscillator and the CMOS RAM.
Figure 5-10 shows typical battery current consumption during battery-backed operation, and Figure 5-11 during normal operation.
Power
Supply
VDIGITAL Sense
The RTC is supplied from one of two power supplies, VSB
or VBAT, according to their levels. An internal voltage comparator delivers the control signals to a pair of switches.
Battery backup voltage VBAT maintains the correct time and
saves the CMOS memory when the VSB voltage is absent,
due to power failure or disconnection of the external AC/DC
input power supply or VSB main battery.
VDIGITAL
IBAT (µA)
ONCTL#
10.0
7.5
5.0
2.5
VSB
Backup
Battery
2.4 3.0 3.6
Figure 5-8. Power Supply Connections
Figure 5-10. Typical Battery Current: Battery
Backed Power Mode @ TC = 25°C
VSB
RTC
VPP
VREF
VSBL
CF
VSB
0.1 µF
CF
VSBL
0.1 µF
VBAT
RUL
Note:
BT1
CF
0.1 µF
Place a 0.1 µF capacitor on each VSB, VSBL
power supply pin as close as possible to the
pin, and also on VBAT.
Figure 5-9. Typical Battery Configuration
124
VBAT (V)
IBAT (µA)
0.75
0.50
0.25
VSB
(V)
3.0 3.3 3.6
Note: Battery voltage in this test is 3.0V.
Figure 5-11. Typical Battery Current: Normal
Operation Mode
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
5.5.2.7 System Power States
The system power state may be No Power, Power On,
Power Off or Power Failure. Table 5-18 indicates the
power-source combinations for each state. No other
power-source combinations are valid.
Power-Up Detection
When system power is restored after a power failure or
power off state (VSB = 0), the lockout condition continues
for a delay of 62 ms (minimum) to 125 ms (maximum) after
the RTC switches from battery to system power.
In addition, the power sources and distribution for the entire
system are illustrated in Figure 5-8 on page 124.
The lockout condition is switched off immediately in the following situations:
Table 5-18. System Power States
VDIGITAL
VSB
VBAT
−
−
−
No Power
−
−
+
Power Failure
−
+
+ or -
Power Off
+
+
+ or -
Power On
Power State
No Power
This state exists when no external or battery power is connected to the device. This condition does not occur once a
backup battery has been connected, except in the case of
a malfunction.
Power On
This is the normal state when the system is active. This
state may be initiated by various events in addition to the
normal physical switching on of the system. In this state,
the system power supply is powered by external AC power
and produces VDIGITAL and VSB. The system and the part
are powered by VDIGITAL, with the exception of the RTC logical device, which is powered by VSB.
Power Off (Suspended)
This is the normal state when the system has been
switched off and is not required to be active, but is still connected to a live external AC input power source. This state
may be initiated directly or by software. The system is powered down. The RTC logical device remains active, powered by VSB.
Power Failure
This state occurs when the external power source to the
system stops supplying power, due to disconnection or
power failure on the external AC input power source. The
RTC continues to maintain timekeeping and RAM data
under battery power (VBAT), unless the oscillator stop bit
was set in the RTC. In this case, the oscillator stops functioning if the system goes to battery power, and timekeeping data becomes invalid.
• If the Divider Chain Control bits, DV[2:0], (CRA bits [6:4])
specify a normal operation mode (01x or 100), all input
signals are enabled immediately upon detection of
system voltage above VSBON.
• When battery voltage is below VBATDCT and HMR is 1,
all input signals are enabled immediately upon detection
of system voltage above VSBON. This also initializes
registers at offsets 00h through 0Dh.
• If bit 7 (VRT) of CRD is 0, all input signals are enabled
immediately upon detection of system voltage above
VSBON.
5.5.2.8 Oscillator Activity
The RTC oscillator is active if:
• VSB power supply is higher than VSBON, independent of
the battery voltage, VBAT
-or• VBAT power supply is higher than VBATMIN, regardless if
VSB is present or not.
The RTC oscillator is disabled if:
• During power-down (VBAT only), the battery voltage
drops below VBATMIN. When this occurs, the oscillator
may be disabled and its functionality cannot be guaranteed.
-or• Software wrote 00x to DV[2:0] bits of the CRA Register
and VSB is removed. This disables the oscillator and
decreases the power consumption from the battery
connected to VBAT. When disabling the oscillator, the
CMOS RAM is not affected as long as the battery is
present at a correct voltage level.
If the RTC oscillator becomes inactive, the following features are dysfunctional/disabled:
• Timekeeping.
• Periodic interrupt.
• Alarm.
System Bus Lockout
During power on or power off, spurious bus transactions
from the host may occur. To protect the RTC internal registers from corruption, all inputs are automatically locked out.
The lockout condition is asserted when VSB is lower than
VSBON.
AMD Geode™ SC3200 Processor Data Book
125
Revision 5.1
SuperI/O Module
5.5.2.9 Interrupt Handling
The RTC has a single Interrupt Request line which handles
the following three interrupt conditions:
• Periodic interrupt.
5.5.2.10 Battery-Backed RAMs and Registers
The RTC has two battery-backed RAMs and 17 registers,
used by the logical units themselves. Battery-backup power
enables information retention during system power down.
The RAMs are:
• Alarm interrupt.
• Standard RAM
• Update end interrupt.
The interrupts are generated if the respective enable bits in
the CRB register are set prior to an interrupt event occurrence. Reading the CRC register clears all interrupt flags.
Thus, when multiple interrupts are enabled, the interrupt
service routine should first read and store the CRC register, and then deal with all pending interrupts by referring to
this stored status.
If an interrupt is not serviced before a second occurrence
of the same interrupt condition, the second interrupt event
is lost. Figure 5-12 illustrates the interrupt timing in the
RTC.
Bit 7
of CRA
A
244 µs
Bit 4
of CRC
P
P/2
Bit 6
of CRC
B
P/2
30.5 µs
C
• Extended RAM
The memory maps and register content of the RAMs is
provided in Section 5.5.4 "RTC General-Purpose RAM
Map" on page 131.
The first 14 bytes and 3 programmable bytes of the Standard RAM are overlaid by time, alarm data and control registers. The remaining 111 bytes are general-purpose
memory.
Registers with reserved bits should be written using the
read-modify-write method.
All register locations within the device are accessed by the
RTC Index and Data registers (at base address and base
address+1). The Index register points to the register location being accessed, and the Data register contains the
data to be transferred to or from the location. An additional
128 bytes of battery-backed RAM (also called Extended
RAM) may be accessed via a second pair of Index and
Data registers.
Access to the two RAMs may be locked. For details see
Table 5-7 on page 115.
Bit 5
of CRC
Flags (and IRQ) are reset at the conclusion of CRC read or by
reset.
A = Update In Progress bit high before update occurs = 244 µs
B = Periodic interrupt to update = Period (periodic int) / 2 +
244 µs
C = Update to Alarm Interrupt = 30.5 µs
P = Period is programmed by RS[3:0] of CRA
Figure 5-12. Interrupt/Status Timing
126
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
5.5.3
RTC Registers
Note:
The RTC registers can be accessed (see Section 5.4.2.1
"LDN 00h - Real-Time Clock" on page 114) at any time during normal operation mode (i.e.,when VSB is within the recommended operation range). This access is disabled
during battery-backed operation. The write operation to
these registers is also disabled if bit 7 of the CRD Register
is 0.
Before attempting to perform any start-up procedures, read about bit 7 (VRT) of the CRD Register.
This section describes the RTC Timing and Control Registers that control basic RTC functionality.
Table 5-19. RTC Register Map
1.
Reset
Type
Index
Type
Name
00h
R/W
SEC. Seconds Register
VPP PUR
01h
R/W
SECA. Seconds Alarm Register
VPP PUR
02h
R/W
MIN. Minutes Register
VPP PUR
03h
R/W
MINA. Minutes Alarm Register
VPP PUR
04h
R/W
HOR. Hours Register
VPP PUR
05h
R/W
HORA. Hours Alarm Register
VPP PUR
06h
R/W
DOW. Day Of Week Register
VPP PUR
07h
R/W
DOM. Date Of Month Register
VPP PUR
08h
R/W
MON. Month Register
VPP PUR
09h
R/W
YER. Year Register
VPP PUR
0Ah
R/W
CRA. RTC Control Register A
Bit specific
0Bh
R/W
CRB. RTC Control Register B
Bit specific
0Ch
RO
CRC. RTC Control Register C
Bit specific
0Dh
RO
CRD. RTC Control Register D
VPP PUR
Programmable1
R/W
DOMA. Date of Month Alarm Register
VPP PUR
Programmable1
R/W
MONA. Month Alarm Register
VPP PUR
Programmable1
R/W
CEN. Century Register
VPP PUR
Overlaid on RAM bytes in range 0Eh-7Fh. See Section 5.4.2.1 "LDN 00h - Real-Time Clock" on page 114.
Table 5-20. RTC Registers
Bit
Description
Index 00h
7:0
Index 01h
7:0
Seconds Register - SEC (R/W)
Reset Type: VPP PUR
Seconds Data. Values may be 00 to 59 in BCD format or 00 to 3B in binary format.
Seconds Alarm Register - SECA (R/W)
Reset Type: VPP PUR
Seconds Alarm Data. Values may be 00 to 59 in BCD format or 00 to 3B in binary format.
When bits 7 and 6 are both set to one (“11”), unconditional match is selected.
Index 02h
7:0
Minutes Register - MIN (R/W)
Reset Type: VPP PUR
Minutes Data. Values can be 00 to 59 in BCD format, or 00 to 3B in binary format.
AMD Geode™ SC3200 Processor Data Book
127
Revision 5.1
SuperI/O Module
Table 5-20. RTC Registers (Continued)
Bit
Description
Index 03h
7:0
Minutes Alarm Register - MINA (R/W)
Reset Type: VPP PUR
Minutes Alarm Data. Values can be 00 to 59 in BCD format, or 00 to 3B in binary format.
When bits 7 and 6 are both set to 1, unconditional match is selected. See Section 5.5.2.5 "Alarms" on page 123 for more
information about “unconditional” matches.
Index 04h
7:0
Hours Data. For 12-hour mode, values can be 01 to 12 (AM) and 81 to 92 (PM) in BCD format, or 01 to 0C (AM) and 81 to
8C (PM) in binary format. For 24-hour mode, values can be 0- to 23 in BCD format or 00 to 17 in binary format.
Index 05h
7:0
Reset Type: VPP PUR
Hours Register - HOR (R/W)
Hours Alarm Register - HORA (R/W)
Reset Type: VPP PUR
Hours Alarm Data. For 12-hour mode, values may be 01 to 12 (AM) and 81 to 92 (PM) in BCD format or 01 to 0C (AM) and
81 to 8C (PM) in Binary format. For 24-hour mode, values may be 0- to 23 in BCD format or 00 to 17 in Binary format.
When bits 7 and 6 are both set to one (“11”), unconditional match is selected.
Index 06h
7:0
Day Of Week Data. Values may be 01 to 07 in BCD format or 01 to 07 in binary format.
Index 07h
7:0
Reset Type: VPP PUR
Day of Week Register - DOW (R/W)
Reset Type: VPP PUR
Date of Month Register - DOM (R/W)
Date Of Month Data. Values may be 01 to 31 in BCD format or 01 to 1F in binary format.
Index 08h
Reset Type: VPP PUR
Month Register - MON (R/W)
Width: Byte
7-0
Month Data. Values may be 01 to 12 in BCD format or 01 to 0C in binary format.
Index 09h
7:0
Year Register - YER (R/W)
Reset Type: VPP PUR
Year Data. Values may be 00 to 99 in BCD format or 00 to 63 in binary format.
Index 0Ah
RTC Control Register A - CRA (R/W)
Reset Type: Bit Specific
This register controls test selection, among other functions. This register cannot be written before reading bit 7 of CRD.
7
Update in Progress. (RO) This bit is not affected by reset. This bit reads 0 when bit 7 of the CRB Register is 1.
0: Timing registers not updated within 244 µs.
1: Timing registers updated within 244 µs.
6:4
Divider Chain Control. These bits control the configuration of the divider chain for timing generation and register bank
selection. See Table 5-21 on page 130. They are cleared to 000 as long as bit 7 of CRD is 0.
3:0
Periodic Interrupt Rate Select. These bits select one of fifteen output taps from the clock divider chain to control the rate of
the periodic interrupt. See Table 5-22 on page 130 and Figure 5-7 on page 122. They are cleared to 000 as long as bit 7 of
CRD is 0.
Index 0Bh
7
RTC Control Register B - CRB (R/W)
Reset Type: Bit Specific
Set Mode. This bit is reset at VPP power-up reset only.
0: Timing updates occur normally.
1: User copy of time is “frozen”, allowing the time registers to be accessed whether or not an update occurs.
6
Periodic Interrupt. Bits [3:0] of the CRA Register determine the rate at which this interrupt is generated. It is cleared to 0 on
RTC reset (i.e., hardware or software reset) or when RTC is disable.
0: Disable.
1: Enable.
5
Alarm Interrupt. This interrupt is generated immediately after a time update in which the seconds, minutes, hours, date and
month time equal their respective alarm counterparts. It is cleared to 0 as long as bit 7 of the CRD Register is reads 0.
0: Disable.
1: Enable.
4
Update Ended Interrupt. This interrupt is generated when an update occurs. It is cleared to 0 on RTC reset (i.e., hardware
or software reset) or when the RTC is disable.
0: Disable.
1: Enable.
128
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
Table 5-20. RTC Registers (Continued)
Bit
3
2
Description
Reserved. This bit is defined as “Square Wave Enable” by the MC146818 and is not supported by the RTC. This bit is
always read as 0.
Data Mode. This bit is reset at VPP power-up reset only.
0: Enable BCD format.
1: Enable Binary format.
1
Hour Mode. This bit is reset at VPP power-up reset only.
0: Enable 12-hour format.
1: Enable 24-hour format.
0
Daylight Saving. This bit is reset at VPP power-up reset only.
0: Disable.
1: Enable:
- In the spring, time advances from1:59:59 AM to 3:00:00 AM on the first Sunday in April.
- In the fall, time returns from 1:59:59 AM to 1:00:00 AM on the last Sunday in October.
Index 0Ch
7
RTC Control Register C - CRC (RO)
Reset Type: Bit Specific
IRQ Flag. Mirrors the value on the interrupt output signal. When interrupt is active, IRQF is 1. To clear this bit (and deactivate the interrupt pin), read the CRC Register as the flag bits UF, AF and PF are cleared after reading this register.
0: IRQ inactive.
1: Logic equation is true: ((UIE and UF) or (AIE and AF) or (PIE and PF)).
6
Periodic Interrupt Flag. Cleared to 0 on RTC reset (i.e., hardware or software reset) or the RTC disabled. In addition, this
bit is cleared to 0 when this register is read.
0: No transition occurred on the selected tap since the last read.
1: Transition occurred on the selected tap of the divider chain.
5
Alarm Interrupt Flag. Cleared to 0 as long as bit 7 of the CRD Register is reads 0. In addition, this bit is cleared to 0 when
this register is read.
0: No alarm detected since the last read.
1: Alarm condition detected.
4
Update Ended Interrupt Flag. Cleared to 0 on RTC reset (i.e., hardware or software reset) or the RTC disabled. In addition, this bit is cleared to 0 when this register is read.
0: No update occurred since the last read.
1: Time registers updated.
3:0
Reserved.
Index 0Dh
7
RTC Control Register D - CRD (RO)
Reset Type: VPP PUR
Valid RAM and Time. This bit senses the voltage that feeds the RTC (VSB or VBAT) and indicates whether or not it was
too low since the last time this bit was read. If it was too low, the RTC contents (time/calendar registers and CMOS RAM) is
not valid.
0: The voltage that feeds the RTC was too low.
1: RTC contents (time/calendar registers and CMOS RAM) are valid.
6:0
Reserved.
Index Programmable
7:0
Date of Month Alarm Register - DOMA (R/W)
Reset Type: VPP PUR
Date of Month Alarm Data. Values may be 01 to 31 in BCD format or 01 to 1F in Binary format.
When bits 7 and 6 are both set to one (“11”), unconditional match is selected. (Default)
Index Programmable
7:0
Month Alarm Register - MONA (R/W)
Reset Type: VPP PUR
Month Alarm Data. Values may be 01 to 12 in BCD format or 01 to 0C in Binary format.
When bits 7 and 6 are both set to one (“11”), unconditional match is selected. (Default)
Index Programmable
7:0
Century Register - CEN (R/W)
Reset Type: VPP PUR
Century Data. Values may be 00 to 99 in BCD format or 00 to 63 in Binary format.
AMD Geode™ SC3200 Processor Data Book
129
Revision 5.1
SuperI/O Module
Table 5-21. Divider Chain Control / Test Selection
DV2
DV1
DV0
CRA6
CRA5
CRA4
0
0
X
Oscillator Disabled
0
1
0
Normal Operation
0
1
1
Test
1
0
X
1
1
X
Table 5-22. Periodic Interrupt Rate Encoding
Rate Select
3210
Periodic Interrupt
Rate (ms)
Divider
Chain Output
0000
No interrupts
0001
3.906250
7
0010
7.812500
8
0011
0.122070
2
0100
0.244141
3
0101
0.488281
4
0110
0.976562
5
0111
1.953125
6
1000
3.906250
7
1001
7.812500
8
1010
15.625000
9
1011
31.250000
10
1100
62.500000
11
1101
125.000000
12
1110
250.000000
13
1111
500.000000
14
Configuration
Divider Chain Reset
Table 5-23. BCD and Binary Formats
Parameter
BCD Format
Seconds
00 to 59
Minutes
00 to 59
Hours
12-hour mode:
Binary Format
00 to 3B
00 to 3B
01 to 12 (AM)
12-hour mode:
81 to 92 (PM)
24-hour mode:
00 to 23
81 to 8C (PM)
24-hour mode:
Day
01 to 07 (Sunday = 01)
01 to 07
Date
01 to 31
01 to 1F
Month
01 to 12 (January = 01)
01 to 0C
Year
00 to 99
00 to 63
Century
00 to 99
00 to 63
130
01 to 0C (AM)
00 to 17
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
5.5.3.1 Usage Hints
1) Read bit 7 of CRD at each system power-up to validate the contents of the RTC registers and the CMOS
RAM. When this bit is 0, the contents of these registers and the CMOS RAM are questionable. This bit is
reset when the backup battery voltage is too low. The
voltage level at which this bit is reset is below the minimum recommended battery voltage, 2.4V. Although
the RTC oscillator may function properly and the register contents may be correct at lower than 2.4V, this bit
is reset since correct functionality cannot be guaranteed. System BIOS may use a checksum method to
revalidate the contents of the CMOS-RAM. The checksum byte should be stored in the same CMOS RAM.
2)
Change the backup battery while normal operating
power is present, and not in backup mode, to maintain
valid time and register information. If a low leakage
capacitor is connected to VBAT, the battery may be
changed in backup mode.
3)
A rechargeable NiCd battery may be used instead of a
non-rechargeable Lithium battery. This is a preferred
solution for portable systems, where small size components is essential.
4)
A supercap capacitor may be used instead of the normal Lithium battery. In a portable system usually the
VSB voltage is always present since the power management stops the system before its voltage falls to
low. The supercap capacitor in the range of 0.0470.47 F should supply the power during the battery
replacement.
AMD Geode™ SC3200 Processor Data Book
5.5.4
RTC General-Purpose RAM Map
Table 5-24. Standard RAM Map
Index
Description
0Eh - 7Fh
Battery-backed general-purpose 111byte RAM.
Table 5-25. Extended RAM Map
Index
00h - 7Fh
Description
Battery-backed general-purpose 128byte RAM.
131
Revision 5.1
5.6
SuperI/O Module
System Wakeup Control (SWC)
The SWC wakes up the system by sending a power-up
request to the ACPI controller in response to the following
maskable system events:
• Modem ring (RI2#)
• Audio Codec event (SDATA_IN2)
• Programmable Consumer Electronics IR (CEIR)
address
Each system event that is monitored by the SWC is fed into
a dedicated detector that decides when the event is active,
according to predetermined (either fixed or programmable)
criteria. A set of dedicated registers is used to determine
the wakeup criteria, including the CEIR address.
A Wakeup Events Status Register (WKSR) and a Wakeup
Events Control Register (WKCR) hold a Status bit and
Enable bit, respectively, for each possible wakeup event.
Upon detection of an active event, the corresponding Status bit is set to 1. If the event is enabled (the corresponding
Enable bit is set to 1), a power-up request is issued to the
ACPI controller. In addition, detection of an active wakeup
event may be also routed to an arbitrary IRQ.
Disabling an event prevents it from issuing power-up
requests, but does not affect the Status bits. A power-up
reset is issued to the ACPI controller when both the Status
and Enable bits are set to 1 for at least one event type.
SWC logic is powered by VSB. The SWC control and configuration registers are battery backed, powered by VPP.
The setup of the wakeup events, including programmable
sequences, is retained throughout power failures (no VSB)
as long as the battery is connected. VPP is taken from VSB
if VSB > 2.0; otherwise, VBAT is used as the VPP source.
Hardware reset does not affect the SWC registers. They
are reset only by a SIO software reset or power-up of VPP.
5.6.1
Event Detection
5.6.1.1 Audio Codec Event
A low-to-high transition on SDATA_IN2 indicates the detection of an Audio Codec event and can be used as a wakeup
event.
5.6.1.2 CEIR Address
A CEIR transmission received on IRRX1 in a pre-selected
standard (NEC, RCA or RC-5) is matched against a programmable CEIR address. Detection of matching can be
used as a wakeup event. The CEIR address detection
operates independently of the serial port with the IR (which
is powered down with the rest of the system).
Whenever an IR signal is detected, the receiver immediately enters the Active state. When this happens, the
receiver keeps sampling the IR input signal and generates
a bit string where a logic 1 indicates an idle condition and a
logic 0 indicates the presence of IR energy. The received
bit string is de-serialized and assembled into 8-bit characters.
The expected CEIR protocol of the received signal should
be configured through bits [5:4] of the CEIR Wakeup Control register (IRWCR) (see Table 5-30 on page 135).
The CEIR Wakeup Address register (IRWAD) holds the
unique address to be compared with the address contained
in the incoming CEIR message. If CEIR is enabled
(IRWCR[0] = 1) and an address match occurs, then the
CEIR Event Status bit of WKSR is set to 1.
The CEIR Address Shift register (ADSR) holds the
received address which is compared with the address contained in the IRWAD. The comparison is affected also by
the CEIR Wakeup Address Mask register (IRWAM) in
which each bit determines whether to ignore the corresponding bit in the IRWAD.
If CEIR routing to interrupt request is enabled, the assigned
SWC interrupt request can be used to indicate that a complete address has been received. To get this interrupt when
the address is completely received, IRWAM should be written with FFh. Once the interrupt is received, the value of
the address can be read from ADSR.
Another parameter that is used to determine whether a
CEIR signal is to be considered valid is the bit cell time
width. There are four time ranges for the different protocols
and carrier frequencies. Four pairs of registers (IRWTRxL
and IRWTRxH) define the low and high limits of each time
range. Table 5-26 lists the recommended time ranges limits for the different protocols and their applicable ranges.
The values are represented in hexadecimal code where
the units are of 0.1 ms.
Table 5-26. Time Range Limits for CEIR Protocols
RC-5
NEC
RCA
Time
Range
Low Limit
High Limit
Low Limit
High Limit
Low Limit
High Limit
0
10h
14h
09h
0Dh
0Ch
12h
1
07h
0Bh
14h
19h
16h
1Ch
2
-
-
50h
64h
B4h
DCh
3
-
-
28h
32h
23h
2Dh
132
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
5.6.2
SWC Registers
• Bank 0 holds reserved registers.
The SWC registers are organized in two banks. The offsets
are related to a base address that is determined by the
SWC Base Address Register in the logical device configuration. The lower three registers are common to the two
banks while the upper registers (03h-0Fh) are divided as
follows:
• Bank 1 holds the CEIR Control Registers.
The active bank is selected through the Configuration Bank
Select field (bits [1:0]) in the Wakeup Configuration Register (WKCFG). See Table 5-29 on page 134.
The tables that follow provide register maps and bit definitions for Banks 0 and 1.
Table 5-27. Banks 0 and 1 - Common Control and Status Register Map
Name
Reset
Value
Offset
Type
00h
R/W1C
WKSR. Wakeup Events Status Register
00h
01h
R/W
WKCR. Wakeup Events Control Register
03h
02h
R/W
WKCFG. Wakeup Configuration Register
00h
Table 5-28. Bank 1 - CEIR Wakeup Configuration and Control Register Map
Reset
Value
Offset
Type
Name
03h
R/W
IRWCR. CEIR Wakeup Control Register
04h
---
05h
R/W
IRWAD. CEIR Wakeup Address Register
00h
06h
R/W
IRWAM. CEIR Wakeup Address Mask Register
E0h
07h
RO
ADSR. CEIR Address Shift Register
00h
08h
R/W
IRWTR0L. CEIR Wakeup, Range 0, Low Limit Register
10h
09h
R/W
IRWTR0H. CEIR Wakeup, Range 0, High Limit Register
14h
0Ah
R/W
IRWTR1L. CEIR Wakeup, Range 1, Low Limit Register
07h
0Bh
R/W
IRWTR1H. CEIR Wakeup, Range 1, High Limit Register
0Bh
0Ch
R/W
IRWTR2L. CEIR Wakeup, Range 2, Low Limit Register
50h
0Dh
R/W
IRWTR2H. CEIR Wakeup, Range 2, High Limit Register
64h
0Eh
R/W
IRWTR3L. CEIR Wakeup, Range 3, Low Limit Register
28h
0Fh
R/W
IRWTR3H. CEIR Wakeup, Range 3, High Limit Register
32h
RSVD. Reserved
AMD Geode™ SC3200 Processor Data Book
00h
---
133
Revision 5.1
SuperI/O Module
Table 5-29. Banks 0 and 1 - Common Control and Status Registers
Bit
Description
Offset 00h
Wakeup Events Status Register - WKSR (R/W1C)
Reset Value: 00h
This register is set to 00h on power-up of VPP or software reset. It indicates which wakeup event and/or PME occurred. (See Section
6.2.9.4 "Power Management Events" on page 176.)
7
Reserved.
6
Reserved. Must be set to 0.
5
IRRX1 (CEIR) Event Status. This sticky bit shows the status of the CEIR event detection.
0: Event not detected. (Default)
1: Event detected.
4:2
1
Reserved.
RI2# Event Status. This sticky bit shows the status of RI2# event detection.
0: Event not detected. (Default)
1: Event detected.
0
SDATA_IN2 Event Status. This sticky bit shows the status of Audio Codec event detection.
0: Event not detected. (Default)
1: Event detected.
Offset 01h
Wakeup Events Control Register - WKCR (R/W)
Reset Value: 03h
This register is set to 03h on power-up of VPP or software reset. Detected wakeup events that are enabled issue a power-up request the
ACPI controller and/or a PME to the Core Logic module. (See Section 6.2.9.4 "Power Management Events" on page 176.)
7
Reserved.
6
Reserved. Must be set to 0.
5
IRRX1 (CEIR) Event Enable.
0: Disable. (Default)
1: Enable.
4:2
1
Reserved.
RI2# Event Enable.
0: Disable.
1: Enable. (Default)
0
SDATA_IN2 Event Enable.
0: Disable.
1: Enable. (Default)
Offset 02h
Wakeup Configuration Register - WKCFG (R/W)
This register is set to 00h on power-up of VPP or software reset. It enables access to CEIR registers.
7:5
Reserved.
4
Reserved. Must be set to 0.
3
Reserved. Must be set to 0.
2
Reserved.
1:0
Reset Value: 00h
Configuration Bank Select Bits.
00: Only shared registers are accessible.
01: Shared registers and Bank 1 (CEIR) registers are accessible.
10: Bank selected.
11: Reserved.
134
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
Table 5-30. Bank 1 - CEIR Wakeup Configuration and Control Registers
Bit
Description
Bank 1, Offset 03h
CEIR Wakeup Control Register - IRWCR (R/W)
This register is set to 00h on power-up of VPP or software reset.
7:6
Reserved.
5:4
CEIR Protocol Select.
Reset Value: 00h
00: RC5
01: NEC/RCA
1x: Reserved
3
Reserved.
2
Invert IRRX Input.
0: Not inverted. (Default)
1: Inverted.
1
Reserved.
0
CEIR Enable.
0: Disable. (Default)
1: Enable.
Bank 1, Offset 04h
Reserved
Bank 1, Offset 05h
CEIR Wakeup Address Register - IRWAD (R/W)
Reset Value: 00h
This register defines the station address to be compared with the address contained in the incoming CEIR message. If CEIR is enabled
(bit 0 of the IRWCR register is 1) and an address match occurs, then bit 5 of the WKSR register is set to 1.
This register is set to 00h on power-up of VPP or software reset.
7:0
CEIR Wakeup Address
Bank 1, Offset 06h
CEIR Wakeup Mask Register - IRWAM (R/W)
Reset Value: E0h
Each bit in this register determines whether the corresponding bit in the IRWAD register takes part in the address comparison. Bits 5, 6,
and 7 must be set to 1 if the RC-5 protocol is selected.
This register is set to E0h on power-up of VPP or software reset.
7:0
CEIR Wakeup Address Mask.
•
If the corresponding bit is 0, the address bit is not masked (enabled for compare).
•
If the corresponding bit is 1, the address bit is masked (ignored during compare).
Bank 1, Offset 07h
CEIR Address Shift Register - ADSR (RO)
This register holds the received address to be compared with the address contained in the IRWAD register.
Reset Value: 00h
This register is set to 00h on power-up of VPP or software reset.
7:0
CEIR Address.
CEIR Wakeup Range 0 Registers
These two registers (IRWTR0L and IRWTR0H) define the low and high limits of time range 0 (see Table 5-26 on page 132). The values
are represented in units of 0.1 ms.
•
RC-5 protocol: The bit cell width must fall within this range for the cell to be considered valid. The nominal cell width is 1.778 ms for a
36 KHz carrier. IRWTR0L and IRWTR0H should be set to 10h and 14h, respectively. (Default)
•
NEC protocol: The time distance between two consecutive CEIR pulses that encodes a bit value of 0 must fall within this range. The
nominal distance for a 0 is 1.125 ms for a 38 KHz carrier. IRWTR0L and IRWTR0H should be set to 09h and 0Dh, respectively.
Bank 1, Offset 08h
IRWTR0L Register (R/W)
This register is set to 10h on power-up of VPP or software reset.
7:5
Reserved.
4:0
CEIR Pulse Change, Range 0, Low Limit.
Bank 1, Offset 09h
IRWTR0H Register (R/W)
This register is set to 14h on power-up of VPP or software reset.
7:5
Reserved.
4:0
CEIR Pulse Change, Range 0, High Limit.
AMD Geode™ SC3200 Processor Data Book
Reset Value: 10h
Reset Value: 14h
135
Revision 5.1
SuperI/O Module
Table 5-30. Bank 1 - CEIR Wakeup Configuration and Control Registers (Continued)
Bit
Description
CEIR Wakeup Range 1 Registers
These two registers (IRWTR1L and IRWTR1H) define the low and high limits of time range 1 (see Table 5-26 on page 132). The values
are represented in units of 0.1 ms.
•
RC-5 protocol: The pulse width defining a half-bit cell must fall within this range in order for the cell to be considered valid. The
nominal pulse width is 0.889 for a 38 KHz carrier. IRWTR1L and IRWTR1H should be set to 07h and 0Bh, respectively. (Default)
•
NEC protocol: The time between two consecutive CEIR pulses that encodes a bit value of 1 must fall within this range. The nominal
time for a 1 is 2.25 ms for a 36 KHz carrier. IRWTR1L and IRWTR1H should be set to 14h and 19h, respectively.
Bank 1, Offset 0Ah
IRWTR1L Register (R/W)
This register is set to 07h on power-up of VPP or software reset.
7:5
Reserved.
4:0
CEIR Pulse Change, Range 1, Low Limit.
Bank 1, Offset 0Bh
IRWTR1H Register (R/W)
This register is set to 0Bh on power-up of VPP or software reset.
7:5
Reserved.
4:0
CEIR Pulse Change, Range 1, High Limit.
Reset Value: 07h
Reset Value: 0Bh
CEIR Wakeup Range 2 Registers
These two registers (IRWTR2L and IRWTR2H) define the low and high limits of time range 2 (see Table 5-26 on page 132). The values
are represented in units of 0.1 ms.
•
RC-5 protocol: These registers are not used when the RC-5 protocol is selected.
•
NEC protocol: The header pulse width must fall within this range in order for the header to be considered valid. The nominal value is
9 ms for a 38 KHz carrier. IRWTR2L and IRWTR2H should be set to 50h and 64h, respectively. (Default)
Bank 1, Offset 0Ch
IRWTR2L Register (R/W)
This register is set to 50h on power-up of VPP or software reset.
7:0
CEIR Pulse Change, Range 2, Low Limit.
Bank 1, Offset 0Dh
IRWTR2H Register (R/W)
This register is set to 64h on power-up of VPP or software reset.
7:0
Reset Value: 50h
Reset Value: 64h
CEIR Pulse Change, Range 2, High Limit.
CEIR Wakeup Range 3 Registers
These two registers (IRWTR3L and IRWTR3H) define the low and high limits of time range 3 (see Table 5-26 on page 132). The values
are represented in units of 0.1 ms.
•
RC-5 protocol: These registers are not used when the RC-5 protocol is selected.
•
NEC protocol: The post header gap width must fall within this range in order for the gap to be considered valid. The nominal value is
4.5 ms for a 36 KHz carrier. IRWTR3L and IRWTR3H should be set to 28h and 32h, respectively. (Default)
Bank 1, Offset 0Eh
IRWTR3L Register (R/W)
This register is set to 28h on power-up of VPP or software reset.
7:0
CEIR Pulse Change, Range 3, Low Limit.
Bank 1, Offset 0Fh
IRWTR3H Register (R/W)
This register is set to 32h on power-up of VPP or software reset.
7:0
136
Reset Value: 28h
Reset Value: 32h
CEIR Pulse Change, Range 3, High Limit.
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
5.7
ACCESS.bus Interface
The SC3200 has two ACCESS.bus (ACB) controllers. ACB
is a two-wire synchronous serial interface compatible with
the ACCESS.bus physical layer, Intel's SMBus, and Philips’
I2C™. The ACB can be configured as a bus master or
slave, and can maintain bidirectional communication with
both multiple master and slave devices. As a slave device,
the ACB may issue a request to become the bus master.
The ACB allows easy interfacing to a wide range of lowcost memories and I/O devices, including: EEPROMs,
SRAMs, timers, ADC, DAC, clock chips and peripheral drivers.
The ACCESS.bus protocol uses a two-wire interface for
bidirectional communication between the ICs connected to
the bus. The two interface lines are the Serial Data Line
(AB1D and AB2D) and the Serial Clock Line (AB1C and
AB2C). (Here after referred to as ABD and ABC unless otherwise specified.) These lines should be connected to a
positive supply via an internal or external pull-up resistor,
and remain high even when the bus is idle.
During each clock cycle, the slave can stall the master
while it handles the previous data or prepares new data.
This can be done for each bit transferred, or on a byte
boundary, by the slave holding ABC low to extend the
clock-low period. Typically, slaves extend the first clock
cycle of a transfer if a byte read has not yet been stored, or
if the next byte to be transmitted is not yet ready. Some
microcontrollers, with limited hardware support for
ACCESS.bus, extend the access after each bit, thus allowing the software to handle this bit.
ABD
ABC
Data Line
Stable:
Data Valid
Change
of Data
Allowed
Each IC has a unique address and can operate as a transmitter or a receiver (though some peripherals are only
receivers).
Figure 5-13. Bit Transfer
During data transactions, the master device initiates the
transaction, generates the clock signal and terminates the
transaction. For example, when the ACB initiates a data
transaction with an attached ACCESS.bus compliant
peripheral, the ACB becomes the master. When the peripheral responds and transmits data to the ACB, their master/
slave (data transaction initiator and clock generator) relationship is unchanged, even though their transmitter/
receiver functions are reversed.
The ACCESS.bus master generates Start and Stop Conditions (control codes). After a Start Condition is generated,
the bus is considered busy and retains this status for a certain time after a Stop Condition is generated. A high-to-low
transition of the data line (ABD) while the clock (ABC) is
high indicates a Start Condition. A low-to-high transition of
the ABD line while the ABC is high indicates a Stop Condition (Figure 5-14).
This section describes the general ACB functional block. A
device may include a different implementation. For device
specific implementation, see Section 5.4.2.5 "LDN 05h and
06h - ACCESS.bus Ports 1 and 2" on page 119.
In addition to the first Start Condition, a repeated Start
Condition can be generated in the middle of a transaction.
This allows another device to be accessed, or a change in
the direction of data transfer.
5.7.1
5.7.2
Start and Stop Conditions
Data Transactions
One data bit is transferred during each clock pulse. Data is
sampled during the high state of the serial clock (ABC).
Consequently, throughout the clock’s high period, the data
should remain stable (see Figure 5-13). Any changes on
the ABD line during the high state of the ABC and in the
middle of a transaction aborts the current transaction. New
data should be sent during the low ABC state. This protocol
permits a single data line to transfer both command/control
information and data, using the synchronous serial clock.
ABD
ABC
S
P
Start
Condition
Stop
Condition
Figure 5-14. Start and Stop Conditions
Each data transaction is composed of a Start Condition, a
number of byte transfers (set by the software) and a Stop
Condition to terminate the transaction. Each byte is transferred with the most significant bit first, and after each byte
(8 bits), an Acknowledge signal must follow. The following
sections provide further details of this process.
AMD Geode™ SC3200 Processor Data Book
137
Revision 5.1
5.7.3
SuperI/O Module
Acknowledge (ACK) Cycle
the ABD line (permits it to go high) to allow the receiver to
send the ACK signal. The receiver must pull down the ABD
line during the ACK clock pulse, signalling that it has correctly received the last data byte and is ready to receive the
next byte. Figure 5-16 illustrates the ACK cycle.
The ACK cycle consists of two signals: the ACK clock pulse
sent by the master with each byte transferred, and the ACK
signal sent by the receiving device (see Figure 5-15).
The master generates the ACK clock pulse on the ninth
clock pulse of the byte transfer. The transmitter releases
Acknowledge
Signal From Receiver
ABD
MSB
ABC
1
S
2 3-6
7
8
1
9
ACK
2
3-8
9
ACK
P
Stop
Condition
Start
Condition
Clock Line Held
Low by Receiver
While Interrupt
is Serviced
Byte Complete
Interrupt Within
Receiver
Figure 5-15. ACCESS.bus Data Transaction
Data Output
by Transmitter
Transmitter Stays Off Bus
During Acknowledge Clock
Data Output
by Receiver
Acknowledge
Signal From Receiver
ABC
S
1
2 3-6
7
8
9
Start
Condition
Figure 5-16. ACCESS.bus Acknowledge Cycle
138
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
5.7.4
Acknowledge After Every Byte Rule
5.7.6
According to this rule, the master generates an acknowledge clock pulse after each byte transfer, and the receiver
sends an acknowledge signal after every byte received.
There are two exceptions to this rule:
• When the master is the receiver, it must indicate to the
transmitter the end of data by not acknowledging (negative acknowledge) the last byte clocked out of the slave.
This negative acknowledge still includes the acknowledge clock pulse (generated by the master), but the
ABD line is not pulled down.
• When the receiver is full, otherwise occupied, or a
problem has occurred, it sends a negative acknowledge
to indicate that it cannot accept additional data bytes.
5.7.5
Addressing Transfer Formats
Each device on the bus has a unique address. Before any
data is transmitted, the master transmits the address of the
slave being addressed. The slave device should send an
acknowledge signal on the ABD line, once it recognizes its
address.
The address consists of the first 7 bits after a Start Condition. The direction of the data transfer (R/W#) depends on
the bit sent after the address, the eighth bit. A low-to-high
transition during a ABC high period indicates the Stop Condition, and ends the transaction of ABD (see Figure 5-17).
When the address is sent, each device in the system compares this address with its own. If there is a match, the
device considers itself addressed and sends an acknowledge signal. Depending on the state of the R/W# bit (1 =
Read, 0 = Write), the device acts either as a transmitter or
a receiver.
The I2C bus protocol allows a general call address to be
sent to all slaves connected to the bus. The first byte sent
specifies the general call address (00h) and the second
byte specifies the meaning of the general call (for example,
write slave address by software only). Those slaves that
require data acknowledge the call, and become slave
receivers; other slaves ignore the call.
Arbitration on the Bus
Multiple master devices on the bus require arbitration
between their conflicting bus access demands. Control of
the bus is initially determined according to address bits and
clock cycle. If the masters are trying to address the same
slave, data comparisons determine the outcome of this
arbitration. In master mode, the device immediately aborts
a transaction if the value sampled on the ABD line differs
from the value driven by the device. (An exception to this
rule is ABD while receiving data. The lines may be driven
low by the slave without causing an abort.)
The ABC signal is monitored for clock synchronization and
to allow the slave to stall the bus. The actual clock period is
set by the master with the longest clock period, or by the
slave stall period. The clock high period is determined by
the master with the shortest clock high period.
When an abort occurs during the address transmission, a
master that identifies the conflict should give up the bus,
switch to slave mode and continue to sample ABD to check
if it is being addressed by the winning master on the bus.
5.7.7
Master Mode
Requesting Bus Mastership
An ACCESS.bus transaction starts with a master device
requesting bus mastership. It asserts a Start Condition, followed by the address of the device it wants to access. If
this transaction is successfully completed, the software
may assume that the device has become the bus master.
For the device to become the bus master, the software
should perform the following steps:
1)
Configure ACBCTL1[2] to the desired operation mode.
(Polling or Interrupt) and set the ACBCTL1[0]. This
causes the ACB to issue a Start Condition on the
ACCESS.bus when the ACCESS.bus becomes free
(ACBCST[1] is cleared, or other conditions that can
delay start). It then stalls the bus by holding ABC low.
2)
If a bus conflict is detected (i.e., another device pulls
down the ABC signal), the ACBST[5] is set.
3)
If there is no bus conflict, ACBST[1] and ACBST[6] are
set.
4)
If the ACBCTL1[2] is set and either ACBST[5] or
ACBST[6] is set, an interrupt is issued.
ABD
ABC
S
1-7
8
9
Start
Condition Address R/W ACK
1-7
Data
8
9
1-7
ACK
Data
8
9
ACK
P
Stop
Condition
Figure 5-17. A Complete ACCESS.bus Data Transaction
AMD Geode™ SC3200 Processor Data Book
139
Revision 5.1
SuperI/O Module
Sending the Address Byte
When the device is the active master of the ACCESS.bus
(ACBST[1] is set), it can send the address on the bus.
Master Receive
After becoming the bus master, the device can start receiving data on the ACCESS.bus.
The address sent should not be the device’s own address,
as defined by ACBADDR[6:0] if ACBADDR[7] is set, nor
should it be the global call address if ACBST[3] is set.
To receive a byte in an interrupt or polling operation, the
software should:
1)
Check that ACBST[6] is set and that ACBST[5] is
cleared. If ACBCTL1[7] is set, also check that the
ACBST[3] is cleared (and clear it if required).
2)
Set ACBCTL1[4] to 1, if the next byte is the last byte
that should be read. This causes a negative acknowledge to be sent.
3)
Read the data byte from the ACBSDA.
To send the address byte, use the following sequence:
1)
2)
3)
For a receive transaction where the software wants
only one byte of data, it should set ACBCTL1[4]. If only
an address needs to be sent or if the device requires
stall for some other reason, set ACBCTL1[7].
Write the address byte (7-bit target device address)
and the direction bit to the ACBSDA register. This
causes the ACB to generate a transaction. At the end
of this transaction, the acknowledge bit received is
copied to ACBST[4]. During the transaction, the ABD
and ABC lines are continuously checked for conflict
with other devices. If a conflict is detected, the transaction is aborted, ACBST[5] is set and ACBST[1] is
cleared.
If ACBCTL1[7] is set and the transaction was successfully completed (i.e., both ACBST[5] and ACBST[4] are
cleared), ACBST[3] is set. In this case, the ACB stalls
any further ACCESS.bus operations (i.e., holds ABC
low). If ACBCTL1[2] is set, it also sends an interrupt
request to the host.
Before receiving the last byte of data, set ACBCTL1[4].
5.7.7.1 Master Stop
To end a transaction, set the ACBCTL1[1] before clearing
the current stall flag (i.e., ACBST[6], ACBST[4], or
ACBST[3]). This causes the ACB to send a Stop Condition
immediately, and to clear ACBCTL1[1]. A Stop Condition
may be issued only when the device is the active bus master (i.e., ACBST[1] is set).
Master Bus Stall
The ACB can stall the ACCESS.bus between transfers
while waiting for the host response. The ACCESS.bus is
stalled by holding the AB1C signal low after the acknowledge cycle. Note that this is interpreted as the beginning of
the following bus operation. The user must make sure that
the next operation is prepared before the flag that causes
the bus stall is cleared.
4)
If the requested direction is transmit and the start
transaction was completed successfully (i.e., neither
ACBST[5] nor ACBST[4] is set, and no other master
has accessed the device), ACBST[6] is set to indicate
that the ACB awaits attention.
5)
If the requested direction is receive, the start transaction was completed successfully and ACBCTL1[7] is
cleared, the ACB starts receiving the first byte automatically.
• Negative acknowledge after sending a byte (ACBST[4] =
1).
Check that both ACBST[5] and ACBST[4] are cleared.
If ACBCTL1[2] is set, an interrupt is generated when
ACBST[5] or ACBST[4] is set.
• ACBCTL1[7] = 1, after a successful start (ACBST[3] =
1).
6)
The flags that can cause a bus stall in master mode are:
• ACBST[6] bit is set.
To transmit a byte in an interrupt or polling controlled operation, the software should:
Repeated Start
A repeated start is performed when the device is already
the bus master (ACBST[1] is set). In this case, the
ACCESS.bus is stalled and the ACB awaits host handling
due to: negative acknowledge (ACBST[4] = 1), empty
buffer (ACBST[6] = 1) and/or a stall after start (ACBST[3]
1).
1)
For a repeated start:
Master Transmit
After becoming the bus master, the device can start transmitting data on the ACCESS.bus.
2)
Check that both ACBST[5] and ACBST[4] are cleared,
and that ACBST[6] is set. If ACBCTL1[7] is set, also
check that ACBST[3] is cleared (and clear it if
required).
Set \ACBCTL1[0] to 1.
2)
In master receive mode, read the last data item from
ACBSDA.
3)
Follow the address send sequence, as described previously in "Sending the Address Byte". If the ACB was
awaiting handling due to ACBST[3] = 1, clear it only
after writing the requested address and direction to
ACBSDA.
Write the data byte to be transmitted to the ACBSDA.
When either ACBST[5] or ACBST[4] is set, an interrupt is
generated. When the slave responds with a negative
acknowledge, ACBST[4] Register is set and ACBST[6]
remains cleared. In this case, if ACBCTL1[2] Register is
set, an interrupt is issued.
140
1)
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
Master Error Detection
The ACB detects illegal Start or Stop Conditions (i.e., a
Start or Stop Condition within the data transfer, or the
acknowledge cycle) and a conflict on the data lines of the
ACCESS.bus. If an illegal condition is detected, ACBST[5]
is set, and master mode is exited (ACBST[1] is cleared).
3)
If ACBCTL1[2] is set, an interrupt is generated if both
ACBCTL1[2] and ACBCTL16 are set.
4)
The software then reads ACBST[0] to identify the
direction requested by the master device. It clears
ACBST[2] so future byte transfers are identified as
data bytes.
Bus Idle Error Recovery
When a request to become the active bus master or a
restart operation fails, ACBST[5] is set to indicate the error.
In some cases, both the device and the other device may
identify the failure and leave the bus idle. In this case, the
start sequence may be incomplete and the ACCESS.bus
may remain deadlocked.
Slave Receive and Transmit
Slave receive and transmit are performed after a match is
detected and the data transfer direction is identified. After a
byte transfer, the ACB extends the acknowledge clock until
the software reads or writes ACBSDA. The receive and
transmit sequences are identical to those used in the master routine.
To recover from deadlock, use the following sequence:
1)
Clear ACBST[5] and ACBCST[1].
2)
Wait for a timeout period to check that there is no other
active master on the bus (i.e., ACBCST[1] remains
cleared).
3)
Disable, and re-enable the ACB to put it in the nonaddressed slave mode. This completely resets the
functional block.
At this point, some of the slaves may not identify the bus
error. To recover, the ACB becomes the bus master: it
asserts a Start Condition, sends an address byte, then
asserts a Stop Condition which synchronizes all the slaves.
5.7.8
Slave Bus Stall
When operating as a slave, the device stalls the
ACCESS.bus by extending the first clock cycle of a transaction in the following cases:
• ACBST[6] is set.
• ACBST[2] and ACBCTL1[6] are set.
Slave Error Detection
The ACB detects illegal Start and Stop Conditions on the
ACCESS.bus (i.e., a Start or Stop Condition within the data
transfer or the acknowledge cycle). When this occurs,
ACBST[5] is set and ACBCST[3:2] are cleared, setting the
ACB as an unaddressed slave.
Slave Mode
A slave device waits in idle mode for a master to initiate a
bus transaction. Whenever the ACB is enabled and it is not
acting as a master (i.e., ACBST[1] is cleared), it acts as a
slave device.
Once a Start Condition on the bus is detected, the device
checks whether the address sent by the current master
matches either:
• The ACBADDR[6:0] value if ACBADDR[7] = 1.
or
• The general call address if ACBCTL1[5] 1.
This match is checked even when ACBST[1] is set. If a bus
conflict (on ABD or ABC) is detected, ACBST[5] is set,
ACBST[1] is cleared and the device continues to search
the received message for a match.
5.7.9
Configuration
ABD and ABC Signals
The ABD and ABC are open-drain signals. The device permits the user to define whether to enable or disable the
internal pull-up of each of these signals.
ACB Clock Frequency
The ACB permits the user to set the clock frequency for the
ACCESS.bus clock. The clock is set by the ACBCTL2[7:1],
which determines the ABC clock period used by the device.
This clock low period may be extended by stall periods initiated by the ACB or by another ACCESS.bus device. In
case of a conflict with another bus master, a shorter clock
high period may be forced by the other bus master until the
conflict is resolved.
If an address match or a global match is detected:
1)
The device asserts its ABD pin during the acknowledge cycle.
2)
ACBCST[2] and ACBST[2] are set. If ACBST[0] = 1
(i.e., slave transmit mode) ACBST[6] is set to indicate
that the buffer is empty.
AMD Geode™ SC3200 Processor Data Book
141
Revision 5.1
5.7.10
SuperI/O Module
ACB Registers
Each functional block is associated with a Logical Device
Number (LDN) (see Section 5.3.2 "Banked Logical Device
Registers" on page 108). ACCESS.Bus Port 1 is assigned
as LDN 05h and ACCESS.bus Port 2 as LDN 06h. In addition to the registers listed here, there are additional configuration registers listed in Section 5.4.2.5 "LDN 05h and 06h
- ACCESS.bus Ports 1 and 2" on page 119.
Table 5-31. ACB Register Map
Reset
Value
Offset
Type
Name
00h
R/W
ACBSDA. ACB Serial Data
xxh
01h
R/W
ACBST. ACB Status
00h
02h
R/W
ACBCST. ACB Control Status
00h
03h
R/W
ACBCTL1. ACB Control 1
00h
04h
R/W
ACBADDR. ACB Own Address
xxh
05h
R/W
ACBCTL2. ACB Control 2
00h
Table 5-32. ACB Registers
Bit
Description
Offset 00h
7:0
ACB Serial Data Register - ACBSDA (R/W)
Reset Value: xxh
ACB Serial Data. This shift register is used to transmit and receive data. The most significant bit is transmitted (received)
first, and the least significant bit is transmitted last. Reading or writing to ACBSDA is allowed only when ACBST[6] is set, or
for repeated starts after setting the ACBCTL1[0]. An attempt to access the register in other cases may produce unpredictable results.
Offset 01h
ACB Status Register - ACBST (R/W)
Reset Value: 00h
This is a read register with a special clear. Some of its bits may be cleared by software, as described below. This register maintains the
current ACB status. On reset, and when the ACB is disabled, ACBST is cleared (00h).
7
SLVSTP (Slave Stop). (R/W1C) Writing 0 to SLVSTP is ignored.
0: Writing 1 or ACB disabled.
1: Stop Condition detected after a slave transfer in which ACBCST[2] or ACBCST[3] was set.
6
SDAST (SDA Status). (RO)
0: Reading from ACBSDA during a receive, or when writing to it during a transmit. When ACBCTL1[0] is set, reading ACBSDA does not clear SDAST. This enables ACB to send a repeated start in master receive mode.
1: SDA Data Register awaiting data (transmit - master or slave) or holds data that should be read (receive - master or
slave).
5
BER (Bus Error). (R/W1C) Writing 0 to this bit is ignored.
0: Writing 1 or ACB disabled.
1: Start or Stop Condition detected during data transfer (i.e., Start or Stop Condition during the transfer of bits [8:2] and
acknowledge cycle), or when an arbitration problem detected.
4
NEGACK (Negative Acknowledge). (R/W1C) Writing 0 to this bit is ignored.
0: Writing 1 or ACB disabled.
1: Transmission not acknowledged on the ninth clock (In this case, SDAST (bit 6) is not set).
3
STASTR (Stall After Start). (R/W1C) Writing 0 to this bit is ignored.
0: Writing 1 or ACB disabled.
1: Address sent successfully (i.e., a Start Condition sent without a bus error, or Negative Acknowledge), if ACBCTL1[7] is
set. This bit is ignored in slave mode. When STASTR is set, it stalls the ACCESS.bus by pulling down the ABC line, and
suspends any further action on the bus (e.g., receive of first byte in master receive mode). In addition, if ACBCTL1[1] is
set, it also causes the ACB to send an interrupt.
142
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
Table 5-32. ACB Registers (Continued)
Bit
2
Description
NMATCH (New Match). (R/W1C) Writing 0 to this bit is ignored. If ACBCTL1[2] is set, an interrupt is sent when this bit is
set.
0: Software writes 1 to this bit.
1: Address byte follows a Start Condition or a repeated start, causing a match or a global-call match.
1
MASTER. (RO)
0: Arbitration loss (BER, bit 5, is set) or recognition of a Stop Condition.
1: Bus master request succeeded and master mode active.
0
XMIT (Transmit). (RO) Direction bit.
0: Master/slave transmit mode not active.
1: Master/slave transmit mode active.
Offset 02h
ACB Control Status Register - ACBCST (R/W)
Reset Value: 00h
This register configures and controls the ACB functional block. It maintains the current ACB status and controls several ACB functions.
On reset and when the ACB is disabled, the non-reserved bits of ACBCST are cleared.
7:6
5
Reserved.
TGABC (Toggle ABC Line). (R/W) Enables toggling the ABC line during error recovery.
0: Clock toggle completed.
1: When the ABD line is low, writing 1 to this bit toggles the ABC line for one cycle. Writing 1 to TGABC while ABD is high
is ignored.
4
TSDA (Test ABD Line). (RO) Reads the current value of the ABD line. It can be used while recovering from an error condition in which the ABD line is constantly pulled low by an out-of-sync slave. Data written to this bit is ignored.
3
GCMTCH (Global Call Match). (RO)
0: Start Condition or repeated Start and a Stop Condition (including illegal Start or Stop Condition).
1: In slave mode, ACBCTL1.GCMEN is set and the address byte (the first byte transferred after a Start Condition) is 00h.
2
MATCH (Address Match). (RO)
0: Start Condition or repeated Start and a Stop Condition (including illegal Start or Stop Condition).
1: ACBADDR[7] is set and the first 7 bits of the address byte (the first byte transferred after a Start Condition) match the 7bit address in ACBADDR.
1
BB (Bus Busy). (R/W1C)
0: Writing 1, ACB disabled, or Stop Condition detected.
1: Bus active (a low level on either ABD or ABC), or Start Condition.
0
BUSY. (RO) This bit should always be written 0. This bit indicates the period between detecting a Start Condition and completing receipt of the address byte. After this, the ACB is either free or enters slave mode.
0: Completion of any state below or ACB disabled.
1: ACB is in one of the following states:
-Generating a Start Condition
-Master mode (ACBST[1] is set)
-Slave mode (ACBCST[2] or ACBCST[3] set).
Offset 03h
7
ACB Control Register 1 - ACBCTL1 (R/W)
Reset Value: 00h
STASTRE (Stall After Start Enable).
0: When cleared, ACBST[3] can not be set. However, if ACBST[3] is set, clearing STASTRE does not clear ACBST[3].
1: Stall after start mechanism enabled, and ACB stalls the bus after the address byte.
6
NMINTE (New Match Interrupt Enable).
0: No interrupt issued on a new match.
1: Interrupt issued on a new match only if ACBCTL1[2] set.
5
GCMEN (Global Call Match Enable).
0: Global call match disabled.
1: Global call match enabled.
AMD Geode™ SC3200 Processor Data Book
143
Revision 5.1
SuperI/O Module
Table 5-32. ACB Registers (Continued)
Bit
4
Description
ACK (Acknowledge). This bit is ignored in transmit mode. When the device acts as a receiver (slave or master), this bit
holds the stop transmitting instruction that is transmitted during the next acknowledge cycle.
0: Cleared after acknowledge cycle.
1: Negative acknowledge issued on next received byte.
3
Reserved.
2
INTEN (Interrupt Enable).
0: ACB interrupt disabled.
1: ACB interrupt enabled. An interrupt is generated in response to one of the following events:
-Detection of an address match (ACBST[2] = 1) and ACBCTL1[6] = 1.
-Receipt of Bus Error (ACBST[5] = 1).
-Receipt of Negative Acknowledge after sending a byte (ACBST[4] = 1).
-Acknowledge of each transaction (same as the hardware set of the ACBST[6]).
-In master mode if ACBCTL1[7] = 1, after a successful start (ACBST[3] = 1).
-Detection of a Stop Condition while in slave mode (ACBST[7] = 1).
1
STOP (Stop).
0: Automatically cleared after Stop issued.
1: Setting this bit in master mode generates a Stop Condition to complete or abort current message transfer.
0
START (Start). Set this bit only when in master mode or when requesting master mode.
0: Cleared after Start Condition sent or Bus Error (ACBST[5] = 1) detected.
1: Single or repeated Start Condition generated on the ACCESS.bus. If the device is not the active master of the bus
(ACBST[1] = 0), setting START generates a Start Condition when the ACCESS.bus becomes free (ACBCST[1] = 0). An
address transmission sequence should then be performed.
If the device is the active master of the bus (ACBST[1] = 1), setting START and then writing to ACBSDA generates a
Start Condition. If a transmission is already in progress, a repeated Start Condition is generated. This condition can be
used to switch the direction of the data flow between the master and the slave, or to choose another slave device without
separating them with a Stop Condition.
Offset 04h
7
ACB Own Address Register - ACBADDR (R/W)
Reset Value: xxh
SAEN (Slave Address Enable).
0: ACB does not check for an address match with ACBADDR[6:0].
1: ACBADDR[6:0] holds a valid address and enables the match of ADDR to an incoming address byte.
6:0
ADDR (Address). These bits hold the 7-bit device address of the SC3200. When in slave mode, the first 7 bits received
after a Start Condition are compared with this field (first bit received is compared with bit 6, and the last bit with bit 0). If the
address field matches the received data and ACBADDR[7] is 1, a match is declared.
Offset 05h
ACB Control Register 2 - ACBCTL2 (R/W)
This register enables/disables the functional block and determines the ACB clock rate.
7:1
Reset Value: 00h
ABCFRQ (ABC Frequency). This field defines the ABC period (low and high time) when the device serves as a bus master. The clock low and high times are defined as follows:
tABCl = tABCh = 2*ABCFRQ*tCLK
where tCLK is the module input clock cycle, as defined in the Section 5.2 "Module Architecture" on page 107.
ABCFRQ can be programmed to values in the range of 0001000b through 1111111b. Using any other value has unpredictable results.
0
EN (Enable).
0: ACB is disabled, ACBCTL1, ACBST and ACBCST registers are cleared, and clocks are halted.
1: ACB is enabled.
144
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
5.8
Legacy Functional Blocks
This section briefly describes the following blocks that provide legacy device functions:
• Parallel Port. (Similar to Parallel Port in the National
Semiconductor PC87338.)
• Serial Port 1 and Serial Port 2 (SP1 and SP2), UART
functionality for both SP1 and SP2. (Similar to SCC1 in
the National Semiconductor PC87338.)
• Infrared Communications Port / Serial Port 3 functionality. (Similar to SCC2 in the National Semiconductor
PC87338.)
The description of each Legacy block includes a general
description, register maps, and bit maps.
5.8.1
Parallel Port
The Parallel Port supports all IEEE1284 standard communication modes: Compatibility (known also as Standard or
SPP), Bidirectional (known also as PS/2), FIFO, EPP
(known also as Mode 4) and ECP (with an optional
Extended ECP mode).
5.8.1.1 Parallel Port Register and Bit Maps
The Parallel Port register maps (Table 5-33 and Table 534) are grouped according to first and second level offsets.
EPP and second level offset registers are available only
when the base address is 8-byte aligned.
Parallel Port functional block bit maps are shown in Table
5-35 and Table 5-36.
Table 5-33. Parallel Port Register Map for First Level Offset
First Level Offset
Type
Name
Modes (ECR Bits) 7 6 5
000h
R/W
DATAR. PP Data
000h
W
AFIFO. ECP Address FIFO
001h
RO
DSR. Status
All Modes
002h
R/W
DCR. Control
All Modes
003h
R/W
ADDR. EPP Address
100
004h
R/W
DATA0. EPP Data Port 0
100
005h
R/W
DATA1. EPP Data Port 1
100
006h
R/W
DATA2. EPP Data Port 2
100
007h
R/W
DATA3. EPP Data Port 3
100
400h
W
CFIFO. PP Data FIFO
010
400h
R/W
DFIFO. ECP Data FIFO
011
400h
R/W
TFIFO. Test FIFO
110
400h
RO
CNFGA. Configuration A
111
401h
RO
CNFGB. Configuration B
111
402h
R/W
ECR. Extended Control
All Modes
403h
R/W
EIR. Extended Index
All Modes
404h
R/W
EDR. Extended Data
All Modes
405h
R/W
EAR. Extended Auxiliary Status
All Modes
000 or 001
011
Table 5-34. Parallel Port Register Map for Second Level Offset
Second Level Offset
Type
Name
00h
R/W
Control0. Control Register 0
02h
R/W
Control2. Control Register 2
04h
R/W
Control4. Control Register 4
05h
R/W
PP Confg0. Parallel Port Configuration Register 0
AMD Geode™ SC3200 Processor Data Book
145
Revision 5.1
SuperI/O Module
Table 5-35. Parallel Port Bit Map for First Level Offset
Bits
Offset
Name
000h
DATAR
Data Bits
AFIFO
Address Bits
001h
DSR
002h
DCR
7
6
Printer
Status
5
ACK#
Status
RSVD
4
3
PE
Status
SLCT
Status
ERR#
Status
Direction
Control
Interrupt
Enable
PP Input
Control
2
RSVD
Printer Initialization
Control
003h
ADDR
EPP Device or Register Selection Address Bits
004h
DATA0
EPP Device or R/W Data
005h
DATA1
EPP Device or R/W Data
006h
DATA2
EPP Device or R/W Data
007h
DATA3
EPP Device or R/W Data
400h
CFIFO
Data Bits
400h
DFIFO
Data Bits
400h
TFIFO
Data Bits
400h
CNFGA
401h
CNFGB
402h
ECR
403h
EIR
404h
EDR
405h
EAR
RSVD
Interrupt Select
ECP Mode Control
ECP Interrupt Mask
Data
Strobe
Control
RSVD
RSVD
ECP DMA
Enable
0
EPP
Timeout
Status
Automatic
Line Feed
Control
Bit 7 of PP
Confg0
Interrupt
Request
Value
RSVD
1
DMA Channel Select
ECP Interrupt Service
RSVD
FIFO
Full
FIFO
Empty
Second Level Offset
Data Bits
FIFO Tag
RSVD
Table 5-36. Parallel Port Bit Map for Second Level Offset
Bits
Offset
Name
00h
Control0
02h
Control2
146
7
6
RSVD
SPP Compatibility
04h
Control4
RSVD
05h
PP Confg0
Bit 3 of
CNFGA
Channel
Address
Enable
5
4
DCR Register Live
Freeze Bit
RSVD
Revision
1.7 or 1.9
Select
PP DMA Request Inactive Time
Demand
DMA
Enable
3
2
1
RSVD
0
EPP Timeout Interrupt Mask
RSVD
RSVD
ECP IRQ Channel Number
PP DMA Request Active Time
PE Internal PU or
PD
ECP DMA Channel
Number
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
5.8.2
UART Functionality (SP1 and SP2)
Both SP1 and SP2 provide UART functionality. The generic
SP1 and SP2 support serial data communication with
remote peripheral device or modem using a wired interface. The functional blocks can function as a standard
16450, 16550, or as an Extended UART.
Bank 3
Bank 2
Bank 1
Bank 0
5.8.2.1 UART Mode Register Bank Overview
Four register banks, each containing eight registers, control
UART operation. All registers use the same 8-byte address
space to indicate offsets 00h through 07h. The BSR register selects the active bank and is common to all banks. See
Figure 5-18.
Offset 07h
5.8.2.2
LCR/BSR
SP1 and SP2 Register and Bit Maps for UART
Functionality
The tables in this subsection provide register and bit maps
for Banks 0 through 3.
Common
Register
Throughout
All Banks
Offset 06h
Offset 05h
Offset 04h
Offset 02h
Offset 01h
Offset 00h
16550 Banks
Figure 5-18. UART Mode Register Bank
Architecture
Table 5-37. Bank 0 Register Map
Offset
Type
00h
RO
RXD. Receiver Data Port
W
TXD. Transmitter Data Port
01h
R/W
IER. Interrupt Enable
02h
RO
EIR. Event Identification (Read Cycles)
R/W
FCR. FIFO Control (Write Cycles)
03h
1.
Name
W
LCR1. Line Control
R/W
BSR1.Bank Select
04h
R/W
MCR. Modem/Mode Control
05h
R/W
LSR. Link Status
06h
R/W
MSR. Modem Status
07h
R/W
SPR. Scratchpad
R/W
ASCR. Auxiliary Status and Control
When bit 7 of this register is set to 1, bits [6:0] of BSR select the bank, as shown in Table 5-38.
AMD Geode™ SC3200 Processor Data Book
147
Revision 5.1
SuperI/O Module
Table 5-38. Bank Selection Encoding
BSR Bits
7
6
5
4
3
2
1
0
Bank Selected
0
x
x
x
x
x
x
x
0
1
0
x
x
x
x
x
x
1
1
1
x
x
x
x
1
x
1
1
1
x
x
x
x
x
1
1
1
1
1
0
0
0
0
0
2
1
1
1
0
0
1
0
0
3
Table 5-39. Bank 1 Register Map
Offset
Type
Name
00h
R/W
LBGD(L). Legacy Baud Generator Divisor Port (Low Byte)
01h
R/W
LBGD(H). Legacy Baud Generator Divisor Port (High Byte)
02h
---
RSVD. Reserved
03h
W
LCR1. Line Control
R/W
BSR1. Bank Select
04h-07h
1.
---
RSVD. Reserved
When bit 7 of this register is set to 1, bits [6:0] of BSR select the bank, as shown in Table 5-38 on page 148.
Table 5-40. Bank 2 Register Map
Offset
Type
Name
00h
R/W
BGD(L). Baud Generator Divisor Port (Low Byte)
01h
R/W
BGD(H). Baud Generator Divisor Port (High Byte)
02h
R/W
EXCR1. Extended Control1
03h
R/W
BSR. Bank Select
04h
R/W
EXCR2. Extended Control 2
05h
---
RSVD. Reserved
06h
RO
RXFLV. RX_FIFO Level
07h
RO
TXFLV. TX_FIFO Level
Table 5-41. Bank 3 Register Map
148
Offset
Type
Name
00h
RO
MRID. Module and Revision ID
01h
RO
SH_LCR. Shadow of LCR
02h
RO
SH_FCR. Shadow of FIFO Control
03h
R/W
BSR. Bank Select
04h-07h
---
RSVD. Reserved
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
Table 5-42. Bank 0 Bit Map
Register
Bits
Offset
Name
00h
RXD
RXD[7:0] (Receiver Data Bits)
TXD
TXD[7:0] (Transmitter Data Bits)
01h
7
6
5
4
3
RSVD
IER1
RSVD
2
IER
TXEMP_IE
3
RSVD /
2
1
0
MS_IE
LS_IE
TXLDL_IE
RXHDL_IE
MS_IE
LS_IE
TXLDL_IE
RXHDL_IE
RXFT
IPR1
IPR0
IPF
MS_EV
LS_EV or
TXHLT_EV
TXLDL_EV
RXHDL_EV
RSVD
TXSR
RXSR
FIFO_EN
PEN
STB
DMA_IE4
02h
EIR1
FEN[1:0]
EIR2
RSVD
RSVD
TXEMP_EV
RSVD 3/
DMA_EV
FCR
03h
04h
RXFTH[1:0]
5
LCR
BKSE
BSR5
BKSE
TXFTH[1:0]
SBRK
STKP
LOOP
WLS[1:0]
RSVD
ISEN or
DCDLP
RILP
RTS
DTR
TX_DFR
RSVD
RTS
DTR
LSR
ER_INF
TXEMP
TXRDY
BRK
FE
PE
OE
RXDA
06h
MSR
DCD
RI
DSR
CTS
DDCD
TERI
DDSR
DCTS
07h
SPR1
S_OET4
RSVD
RXF_TOUT
1
0
MCR2
05h
ASCR2
1.
2.
3.
4.
5.
EPS
BSR[6:0] (Bank Select)
RSVD
MCR1
4
Scratch Data
RSVD
TXUR4
RXACT4
RXWDG4
RSVD
Non-Extended Mode.
Extended Mode.
In SP1 only.
In SP2 only.
When bit 7 of this register is set to 1, bits [6:0] of BSR select the bank, as shown in Table 5-38 on page 148.
Table 5-43. Bank 1 Bit Map
Register
Offset
Name
7
6
5
4
3
00h
LBGD(L)
LBGD[7:0] (Low Byte)
01h
LBGD(H)
LBGD[15:8] (High Byte)
02h
RSVD
03h
1
LCR
BKSE
BSR1
BKSE
04h-07h
1.
Bits
2
Reserved
SBRK
RSVD
STKP
EPS
PEN
STB
WLS[1:0]
BSR[6:0] (Bank Select)
Reserved
When bit 7 of this register is set to 1, bits [6:0] of BSR select the bank, as shown in Table 5-38 on page 148.
AMD Geode™ SC3200 Processor Data Book
149
Revision 5.1
SuperI/O Module
Table 5-44. Bank 2 Bit Map
Register
Offset
Name
Bits
7
6
5
4
3
2
1
00h
BGD(L)
BGD[7:0] (Low Byte)
01h
BGD(H)
BGD [15:8] (High Byte)
02h
EXCR1
BTEST
03h
BSR
BKSE
04h
EXCR2
LOCK
05h
RSVD
06h
RXFLV
RSVD
RFL[4:0]
07h
TXFLV
RSVD
TFL[4:0]
RSVD
ETDLBK
LOOP
0
RSVD
EXT_SL
BSR[6:0] (Bank Select)
RSVD
PRESL[1:0]
RSVD
Reserved
Table 5-45. Bank 3 Bit Map
Register
Offset
Name
00h
MRID
01h
SH_LCR
02h
SH_FCR
03h
BSR
04h-07h
RSVD
150
Bits
7
6
5
4
3
2
MID[3:0]
BKSE
SBRK
RXFTH[1:0]
BKSE
1
0
RID[3:0]
STKP
EPS
TXFHT[1:0]
PEN
STB
RSVD
TXSR
WLS[1:0]
RXSR
FIFO_EN
BSR[6:0] (Bank Select)
RSVD
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
5.8.3
IR Communications Port (IRCP) / Serial
Port 3 (SP3) Functionality
Bank 7
This section describes the IRCP/SP3 support registers.
The IRCP/SP3 functional block provides advanced, versatile serial communications features with IR capabilities.
Bank 6
Bank 5
Bank 4
Bank 3
Bank 2
Bank 1
The IRCP/SP3 also supports two DMA channels; the functional block can use either one or both of them. One channel is required for IR-based applications, since IR
communication works in half duplex fashion. Two channels
would normally be needed to handle high-speed full duplex
IR based applications.
Bank 0
The IRCP or Serial Port 3 is chosen via bit 6 of the PMR
Register (see Section 4.2 "Multiplexing, Interrupt Selection,
and Base Address Registers" on page 88).
Offset 07h
5.8.3.1 IR/SP3 Mode Register Bank Overview
Eight register banks, each containing eight registers, control IR/SP3 operation. All registers use the same 8-byte
address space to indicate offsets 00h through 07h. The
BSR register selects the active bank and is common to all
banks. See Figure 5-19.
Offset 05h
5.8.3.2 IRCP/SP3 Register and Bit Maps
The tables in this subsection provide register and bit maps
for Banks 0 through 7.
Offset 01h
Offset 06h
Offset 04h
LCR/BSR
Offset 02h
Offset 00h
Common
Register
Throughout
All Banks
Figure 5-19. IRCP/SP3 Register Bank
Architecture
Table 5-46. Bank 0 Register Map
Offset
Type
00h
RO
RXD. Receive Data Port
W
TXD. Transmit Data Port
01h
R/W
IER. Interrupt Enable
02h
RO
EIR. Event Identification
R/W
FCR. FIFO Control
W
LCR1. Link Control
R/W
BSR1. Bank Select
04h
R/W
MCR. Modem/Mode Control
05h
R/W
LSR. Link Status
06h
R/W
MSR. Modem Status
07h
R/W
SPR. Scratchpad
R/W
ASCR. Auxiliary Status and Control
03h
1.
Name
When bit 7 of this register is set to 1, bits [6:0] of BSR select the bank, as shown in Table 5-47.
AMD Geode™ SC3200 Processor Data Book
151
Revision 5.1
SuperI/O Module
Table 5-47. Bank Selection Encoding
BSR Bits
7
6
5
4
3
2
1
0
Bank Selected
Functionality
0
x
x
x
x
x
x
x
0
UART + IR
1
0
x
x
x
x
x
x
1
1
1
x
x
x
x
1
x
1
1
1
x
x
x
x
x
1
1
1
1
1
0
0
0
0
0
2
1
1
1
0
0
1
0
0
3
1
1
1
0
1
0
0
0
4
1
1
1
0
1
1
0
0
5
1
1
1
1
0
0
0
0
6
1
1
1
1
0
1
0
0
7
IR Only
Table 5-48. Bank 1 Register Map
Offset
Type
Name
00h
R/W
LBGD(L). Legacy Baud Generator Divisor Port (Low Byte)
01h
R/W
LBGD(H). Legacy Baud Generator Divisor Port (High Byte)
02h
---
RSVD. Reserved
03h
W
LCR1. Link Control
R/W
BSR1. Bank Select
04h-07h
1.
---
RSVD. Reserved
When bit 7 of this register is set to 1, bits [6:0] of BSR select the bank, as shown in Table 5-47.
Table 5-49. Bank 2 Register Map
152
Offset
Type
Name
00h
R/W
BGD(L). Baud Generator Divisor Port (Low Byte)
01h
R/W
BGD(H). Baud Generator Divisor Port (High Byte)
02h
R/W
EXCR1. Extended Control 1
03h
R/W
BSR. Bank Select
04h
R/W
EXCR2. Extended Control 2
05h
---
RSVD. Reserved
06h
RO
TXFLV. TX FIFO Level
07h
RO
RXFLV. RX FIFO Level
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
Table 5-50. Bank 3 Register Map
Offset
Type
Name
00h
RO
MID. Module and Revision Identification
01h
RO
SH_LCR. Link Control Shadow
02h
RO
SH_FCR. FIFO Control Shadow
03h
R/W
BSR. Bank Select
04h-07h
---
RSVD. Reserved
Table 5-51. Bank 4 Register Map
Offset
Type
00h
RO
TMR(L). TImer (Low Byte)
01h
RO
TMR(H). Timer (High Byte)
02h
R/W
IRCR1. IR Control 1
03h
R/W
BSR. Bank Select
04h
R/W
TFRL(L). Transmission Frame Length (Low Byte)
RO
TFRCC(L). Transmission Current Count (Low Byte)
R/W
TFRL(H). Transmission Frame Length (High Byte)
RO
TFRCC(H). Transmission Current Count (High Byte)
R/W
RFRML(L). Reception Frame Maximum Length (Low Byte)
RO
RFRCC(L). Reception Frame Current Count (Low Byte)
R/W
RFRML(H). Reception Frame Maximum Length (High Byte)
RO
RFRCC(H). Reception Frame Current Count (High Byte)
05h
06h
07h
Name
Table 5-52. Bank 5 Register Map
Offset
Type
Name
00h
R/W
SPR3. Scratchpad 2
01h
R/W
SPR3. Scratchpad 3
02h
R/W
RSVD. Reserved
03h
R/W
BSR. Bank Select
04h
R/W
IRCR2. IR Control 2
05h
RO
FRM_ST. Frame Status
06h
RO
RFRL(L). Received Frame Length (Low Byte)
RO
LSTFRC. Lost Frame Count
RO
RFRL(H). Received Frame Length (High Byte)
07h
AMD Geode™ SC3200 Processor Data Book
153
Revision 5.1
SuperI/O Module
Table 5-53. Bank 6 Register Map
Offset
Type
Name
00h
R/W
IRCR3. IR Control 3
01h
R/W
MIR_PW. MIR Pulse Width
02h
R/W
SIR_PW. SIR Pulse Width
03h
R/W
BSR. Bank Select
04h
R/W
BFPL. Beginning Flags/Preamble Length
05h-07h
---
RSVD. Reserved
Table 5-54. Bank 7 Register Map
Offset
Type
Name
00h
R/W
IRRXDC. IR Receiver Demodulator Control
01h
R/W
IRTXMC. IR Transmitter Modulator Control
02h
R/W
RCCFG. Consumer IR (CEIR) Configuration
03h
R/W
BSR. Bank Select
04h
R/W
IRCFG1. IR Interface Configuration 1
05h-06h
---
07h
R/W
RSVD. Reserved
IRCFG4. IR Interface Configuration 4
Table 5-55. Bank 0 Bit Map
Register
Bits
Offset
Name
00h
RXD
RXD[7:0] (Receive Data)
TXD
TXD[7:0] (Transmit Data)
01h
6
TMR_IE
EIR
FCR
4
SFIF_IE
TXEMP_
IE/PLD_IE
FEN[1:0]
EIR1
2
5
3
RSVD
IER1
IER2
02h
7
TMR_EV
RSVD
SFIF_EV
RXFTH[1:0]
03h
LCR
BKSE
BSR
BKSE
04h
MCR1
DMA_IE
SBRK
TXEMP_EV/
PLD_EV
1
0
MS_IE
LS_IE
TXLDL_IE
RXHDL_IE
MS_IE
LS_IE
TXLDL_IE
RXHDL_IE
RXFT
DMA_EV
TXFTH[1:0]
STKP
2
EPS
IPR[1:0]
IPF
MS_EV
LS_EV/
TXHLT_EV
TXLDL_EV
RXHDL_EV
RSVD
TXSR
RXSR
FIFO_EN
PEN
STB
WLS[1:0]
BSR[6:0] (Bank Select)
RSVD
MDSL[2:0]
LOOP
ISEN/
DCDLP
RILP
RTS
DTR
IR_PLS
TX_DFR
DMA_EN
RTS
DTR
05h
LSR
ER_INF/
FR_END
TXEMP
TXRDY
BRK/
MAX_LEN
FE/
PHY_ERR
PE/
BAD_CRC
OE
RXDA
06h
MSR
DCD
RI
DSR
CTS
DDCD
TERI
DDSR
DCTS
07h
1
S_EOT
FEND_INF
RXF_TOUT
MCR2
SPR
ASCR2
1.
2.
154
Scratch Data
CTE/PLD
TXUR
RXACT/
RXBSY
RXWDG/
LOST_FR
TXHFE
Non-extended mode.
Extended mode.
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
SuperI/O Module
Table 5-56. Bank 1 Bit Map
Register
Offset
Bits
Name
7
6
5
4
3
2
00h
LBGD(L)
LBGD[7:0] (Low Byte Data)
01h
LBGD(H)
LBGD[15:8] (High Byte Data)
02h
RSVD
03h
LCR
BKSE
BSR
BKSE
04h-07h
1
0
RSVD
SBRK
STKP
EPS
PEN
STB
WLS[1:0]
BSR[6:0] (Bank Select)
RSVD
RSVD
Table 5-57. Bank 2 Bit Map
Register
Offset
Bits
Name
7
6
5
4
3
00h
BGD(L)
BGD[7:0] (Low Byte Data)
01h
BGD(H)
BGD[15:8] (High Byte Data)
02h
EXCR1
BTEST
RSVD
ETDLBK
LOOP
DMASWP
2
1
0
DMATH
DMANF
EXT_SL
03h
BSR
BKSE
04h
EXCR2
LOCK
BSR[6:0] (Bank Select)
05h
RSVD
06h
TXFLV
RSVD
TFL[5:0]
07h
RXFLV
RSVD
RFL[5:0]
RSVD
PRESL[1:0]
RF_SIZ[1:0]
TF_SIZ[1:0]
RSVD
Table 5-58. Bank 3 Bit Map
Register
Offset
Name
00h
MID
SH_LCR
02h
SH_FCR2
03h
BSR
RSVD
7
6
RSVD
SBRK
5
4
3
2
STKP
EPS
PEN
STB
RSVD
TXSR
MID[3:0]
01h
04h-07h
1.
2.
Bits
1
1
0
RID[3:0]
RXFTH[1:0]
TXFTH[1:0]
BKSE
WLS[1:0]
RXSR
FIFO_EN
1
0
BSR[6:0] (Bank Select)
Reserved
LCR Register Value
FCR Register Value
Table 5-59. Bank 4 Bit Map
Register
Offset
Name
00h
TMR(L)
01h
TMR(H)
02h
IRCR1
03h
BSR
04h
TFRL(L)/
TFRCC(L)
05h
TFRL(H)/
TFRCC(H)
Bits
7
6
5
4
3
2
TMR[7:0] (Low Byte Data)
RSVD
RSVD
BKSE
TMR[11:8] (High Byte Data)
IR_SL[1:0]
CTEST
TMR_EN
BSR[6:0] (Bank Select)
TFRL[7:0] / TFRCC[7:0] (Low Byte Data)
RSVD
AMD Geode™ SC3200 Processor Data Book
TFRL[12:8] / TFRCC[12:8] (High Byte Data)
155
Revision 5.1
SuperI/O Module
Table 5-59. Bank 4 Bit Map (Continued)
Register
Offset
Name
06h
RFRML(L)/
RFRCC(L)
07h
RFRML(H)/
RFRCC(H)
Bits
7
6
5
4
3
2
1
0
RFRML[7:0] / RFRCC[7:0] (Low Byte Data)
RSVD
RFRML[12:8] / RFRCC[12:8] (High Byte Data)
Table 5-60. Bank 5 Bit Map
Register
Bits
Offset
Name
7
6
5
4
3
2
1
0
00h
SPR2
Scratchpad 2
01h
SPR3
Scratchpad 2
02h
RSVD
03h
BSR
BKSE
04h
IRCR2
RSVD
SFTSL
FEND_MD
AUX_IRRX
05h
FRM_ST
VLD
LOST_FR
RSVD
MAX_LEN
TX_MS
MDRS
IRMSSL
IR_FDPLX
PHY_ERR
BAD_CRC
OVR1
OVR2
06h
RFRL(L)/
LSTFRC
RFRL[7:0] (Low Byte Data) / LSTFRC[7:0]
07h
RFRL(H)
RFRL[15:8] (High Byte Data)
1
0
RSVD
BSR[6:0] (Bank Select)
Table 5-61. Bank 6 Bit Map
Register
Offset
Bits
Name
7
6
00h
IRCR3
SHDM_DS
SHMD_DS
01h
MIR_PW
RSVD
MPW[3:0]
02h
SIR_PW
RSVD
SPW[3:0]
03h
BSR
04h
BFPL
05h-07h
RSVD
5
4
3
FIR_CRC
MIR_CRC
RSVD
BKSE
2
TXCRC_INV TXCRC_DS
RSVD
BSR[6:0] (Bank Select)
MBF[3:0]
FPL[3:0]
RSVD
Table 5-62. Bank 7 Bit Map
Register
Bits
Offset
Name
00h
IRRXDC
DBW[2:0]
DFR[4:0]
01h
IRTXMC
MCPW[2:0]
MCFR[4:0]
02h
RCCFG
R_LEN
03h
BSR
BKSE
STRV_MS
04h
IRCFG1
05h-06h
RSVD
07h
IRCFG4
156
7
6
T_OV
5
RXHSC
4
3
RCDM_DS
2
RSVD
TXHSC
1
0
RC_MMD[1:0]
BSR[6:0] (Bank Select)
SIRC[2:0]
IRID3
IRIC[2:0]
IRSL21_DS
RSVD
RSVD
RSVD
IRRX_MD
IRSL0_DS
RXINV
AMD Geode™ SC3200 Processor Data Book
Core Logic Module
Revision 5.1
6
6.0Core Logic Module
The Core Logic module is an enhanced PCI-to-Sub-ISA
bridge (South Bridge), this module is ACPI-compliant, and
provides AT/Sub-ISA functionality. The Core Logic module
also contains state-of-the-art power management. Two bus
mastering IDE controllers are included for support of up to
four ATA-compliant devices. A three-port Universal Serial
Bus (USB) provides high speed, and Plug & Play expansion for a variety of new consumer peripheral devices.
6.1
Feature List
Internal Fast-PCI Interface
The internal Fast-PCI bus interface is used to connect the
Core Logic and GX1 modules of the SC3200. This interface includes the following features:
• PCI protocol for transfers on Fast-PCI bus
• Up to 66 MHz operation
• Subtractive decode handled internally in conjunction
with external PCI bus
• PCI-to-Sub-ISA interrupt mapper/translator
• External PCI bus
— Devices internal to the Core Logic module (IDE,
Audio, USB, Sub-ISA, etc.) cannot master to memory
through the external PCI bus.
— Legacy DMA is not supported to memory located on
external PCI bus.
— The Core Logic module does not transfer subtractively decoded I/O cycles originating from the
external PCI bus.
AT Compatibility
• 8259A-equivalent interrupt controllers
• 8254-equivalent timer
• 8237-equivalent DMA controllers
• Port A, B, and NMI logic
• Positive decode for AT I/O space
Sub-ISA Interface
Bus Mastering IDE Controllers
• Boot ROM chip select
• Two controllers with support for up to four IDE devices
• Extended ROM to 16 MB
• Independent timing for master and slave devices for both
channels
• Two general-purpose chip selects
• PCI bus master burst reads and writes
• Multiword DMA support
• NAND Flash support
• M-Systems DiskOnChip support
• Is not the subtractive decode agent
• Programmed I/O (PIO) Modes 0-4 support
Power Management
Universal Serial Bus
• Three independent USB interfaces
• Open Host Controller Interface (OpenHCI) specification
compliant
• Automated CPU 0V Suspend modulation
• I/O Traps and Idle Timers for peripheral power management
• Software SMI and Stop Clock for APM support
PCI Interface
• ACPI-compliant timer and register set
• PCI 2.1 compliant
• Up to 22 GPIOs of which all can generate Power
Management Interrupts (PMEs)
• PCI master for AC97 and IDE controllers
• Subtractive agent for unclaimed transactions
• Three Dedicated GPWIOs powered by VSBL and VSB
• Supports PCI initiator-to-Sub-ISA cycle translations
• Shadow register support for legacy controllers for 0V
Suspend
AMD Geode™ SC3200 Processor Data Book
157
Revision 5.1
Core Logic Module
Integrated Audio
6.2
• AC97 Version 2.0 compliant interface to audio codecs
The Core Logic architecture provides the internal functional
blocks shown in Figure 6-1.
• Secondary codec support
Module Architecture
• Fast-PCI interface to external PCI bus
• AMC97 codec support
• IDE controllers (UDMA-33)
Video Processor Interface
• USB controllers
• Synchronous serial interface to the Video Processor
• Sub-ISA bus interface
• Translates video and clock control register accesses
from PCI to serial interface
• AT compatibility logic (legacy)
• ACPI compliant power management (includes GPIO
interfaces, such as joystick)
• Supports both reads and writes of Video Processor
registers
• Integrated audio controller
• Retries Fast-PCI bus accesses until Core Logic
completes the transfer over the serial interface
• Low Pin Count (LPC) Interface
Low Pin Count (LPC) Interface
• Based on Intel LPC Interface Specification Revision 1.0
• Serial IRQ support
Fast-PCI
UDMA33
IDE
33-66 MHz
Fast X-Bus
PCI
PCI Interface
33 MHz
Config.
Reg.
X-Bus
GPIOs
GPIOs
PW
ACPI/PM
LPC
LPC
USB
USB
Audio
Controller
AC97
Legacy
ISA/PIC/PIT/DMA
Sub-ISA
Figure 6-1. Core Logic Module Block Diagram
158
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module
6.2.1
Fast-PCI Interface to External PCI Bus
The Core Logic module provides a PCI bus interface that is
both a slave for PCI cycles initiated by the GX1 module or
other PCI master devices, and a non-preemptive master for
DMA transfer cycles. It is also a standard PCI master for
the IDE controllers and audio I/O logic. The Core Logic
supports positive decode for configurable memory and I/O
regions, and implements a subtractive decode option for
unclaimed PCI accesses. It also generates address and
data parity, and performs parity checking. The arbiter for
the Fast-PCI interface is located in the GX1 module.
Configuration registers are accessed through the PCI interface using the PCI Bus Type 1 configuration mechanism as
described in the PCI Specification.
6.2.1.1 Processor Mastered Cycles
The Core Logic module acts on all processor initiated
cycles according to PCI rules for active/subtractive decode
using DEVSEL#. Memory writes are automatically posted.
Reads are retried if they are not destined for actively
decoded (i.e., positive decode) devices on the high speed
X-Bus or the 33 MHz X-Bus. This means that reads to
external PCI, LPC, or Sub-ISA devices are automatically
treated as delayed transactions through the PCI retry
mechanism. This allows the high bandwidth devices
access to the Fast-PCI interface while the response from a
slow device is accumulated.
Bursting from the host is not supported.
All types of configuration cycles are supported and handled
appropriately according to the PCI specification.
6.2.1.2 External PCI Mastered Cycles
Memory cycles mastered by external PCI devices on the
external PCI bus are actively taken if they are to the system
memory address range. Memory cycles to system memory
are forwarded to the Fast-PCI interface. Burst transfers are
stopped on every cache line boundary to allow efficient
buffering in the Fast-PCI interface block.
I/O and configuration cycles mastered by external PCI
devices which are subtractively decoded by the Core Logic
module, are not handled.
6.2.1.3
Core Logic Internal or Sub-ISA Mastered
Cycles
Only memory cycles (not I/O cycles) are supported by the
internal Sub-ISA or legacy DMA masters. These memory
cycles are always forwarded to the Fast-PCI interface.
6.2.1.4 External PCI Bus
The external PCI bus is a fully-compliant PCI bus. PCI slots
are connected to this bus. Support for up to two bus masters is provided. The arbiter is in the Core Logic module.
AMD Geode™ SC3200 Processor Data Book
6.2.1.5 Bus Master Request Priority
The Fast-PCI bus supports seven bus masters. The
requests (REQs) are fixed in priority. The seven bus masters in order of priority are:
1)
2)
3)
4)
5)
6)
7)
VIP
IDE Channel 0
IDE Channel 1
Audio
USB
External REQ0#
External REQ1#
6.2.2
PSERIAL Interface
The majority of the system power management logic is
implemented in the Core Logic module, but a minimal
amount of logic is contained within the GX1 module to provide information that is not externally visible (e.g., graphics
controller).
The GX1 module implements a simple serial communications mechanism to transmit the CPU status to the Core
Logic module via internal signal PSERIAL. The GX1 module accumulates CPU events in an 8-bit register which it
transmits serially every 1 to 10 µs.
The packet transmitter holds the serial output internal signal (PSERIAL) low until the transmission interval counter
has elapsed. Once the counter has elapsed, the PSERIAL
signal is held high for two clocks to indicate the start of
packet transmission. The contents of the Serial Packet register are then shifted out starting from bit 7 down to bit 0.
The PSERIAL signal is held high for one clock to indicate
the end of packet transmission and then remains low until
the next transmission interval. After the packet transmission is complete, the GX1 module’s Serial Packet register’s
contents are cleared.
The GX1 module’s input clock is used as the clock reference for the serial packet transmitter.
Once a bit in the register is set, it remains set until the completion of the next packet transmission. Successive events
of the same type that occur between packet transmissions
are ignored. Multiple unique events between packet transmissions accumulate in this register. The GX1 module
transmits the contents of the serial packet only when a bit
in the Serial Packet register is set and the interval counter
has elapsed.
The Core Logic module decodes the serial packet after
each transmission and performs the power management
tasks related to video retrace.
For more information on the Serial Packet register refer to
the AMD Geode™ GX1 Processor Data Book.
159
Revision 5.1
6.2.2.1 Video Retrace Interrupt
Bit 7 of the “Serial Packet” can be used to generate an SMI
whenever a video retrace occurs within the GX1 module.
This function is normally not used for power management
but for SoftVGA routines. Setting F0 Index 83h[2] = 1
enables this function. A read only status register located at
F1BAR0+I/O Offset 00h[5] can be read to see if the SMI
was caused by a video retrace event.
6.2.3
IDE Controller
The Core Logic module integrates a PCI bus mastering,
ATA-4 compatible IDE controller. This controller supports
UltraDMA, Multiword DMA and Programmed I/O (PIO)
modes. Two devices are supported on the IDE controller.
The data-transfer speed for each device can be independently programmed. This allows high-speed IDE peripherals to coexist on the same channel as lower speed devices.
The Core Logic module supports two IDE channels, a primary channel and a secondary channel.
The IDE interface provides a variety of features to optimize
system performance, including 32-bit disk access, post
write buffers, bus master, Multiword DMA, look-ahead read
buffer, and prefetch mechanism for each channel respectively.
The IDE interface timing is completely programmable. Timing control covers the command active and recover pulse
widths, and command block register accesses. The IDE
data-transfer speed for each device on each channel can
be independently programmed allowing high-speed IDE
peripherals to coexist on the same channel as older, compatible devices.
The Core Logic module also provides a software accessible buffered reset signal to the IDE drive, F0 Index 44h[2].
The IDE_RST# signal can be driven low or high as needed
for device-power-off conditions. IDE_RST# is not driven
low by POR# (Power-On Reset).
6.2.3.1 IDE Configuration Registers
Registers for configuring Channels 0 and 1 are located in
the PCI register space designated as Function 2 (F2 Index
40h-5Ch). Table 6-35 on page 273 provides the bit formats
for these registers. The IDE bus master configuration registers are accessed via F2 Index 20h which is Base Address
Register 4 in Function 2 (F2BAR4). See Table 6-36 on
page 277 for register/bit formats.
The following subsections discuss Core Logic operational/
programming details concerning PIO, Bus Master, and
UltraDMA/33 modes.
6.2.3.2 PIO Mode
The IDE data port transaction latency consists of address
latency, asserted latency and recovery latency. Address
latency occurs when a PCI master cycle targeting the IDE
data port is decoded, and the IDE_ADDR[2:0] and
IDE_CS# lines are not set up. Address latency provides the
setup time for the IDE_ADDR[2:0] and IDE_CS# lines prior
to IDE_IOR# and IDE_IOW#.
160
Core Logic Module
Asserted latency consists of the I/O command strobe
assertion length and recovery time. Recovery time is provided so that transactions may occur back-to-back on the
IDE interface without violating minimum cycle periods for
the IDE interface.
If IDE_IORDY is asserted when the initial sample point is
reached, no wait states are added to the command strobe
assertion length. If IDE_IORDY is negated when the initial
sample point is reached, additional wait states are added.
Recovery latency occurs after the IDE data port transactions have completed. It provides hold time on the
IDE_ADDR[2:0] and IDE_CS# lines with respect to the
read and write strobes (IDE_IOR# and IDE_IOW#).
The PIO portion of the IDE registers is enabled through:
• Channel 0 Drive 0 Programmed I/O Register
(F2 Index 40h)
• Channel 0 Drive 1 Programmed I/O Register
(F2 Index 48h)
• Channel 1 Drive 0 Programmed I/O Register
(F2 Index 50h)
• Channel 1 Drive 1 Programmed I/O Register
(F2 Index 58h)
The IDE channels and devices can be individually programmed to select the proper address setup time, asserted
time, and recovery time.
The bit formats for these registers are shown in Table 6-35
on page 273. Note that there are different bit formats for
each of the PIO programming registers depending on the
operating format selected: Format 0 or Format 1:
• F2 Index 44h[31] (Channel 0 Drive 0 — DMA Control
Register) sets the format of the PIO register.
— If bit 31 = 0, Format 0 is used and it selects the
slowest PIO mode (bits [19:16]) per channel for
commands.
— If bit 31 = 1, Format 1 is used and it allows independent control of command and data.
Also listed in the bit formats are recommended values for
the different PIO modes. Note that these are only recommended settings and are not 100% tested.
When using independent control of command and data
cycles the following algorithm should be used when two
IDE devices are sharing the same channel:
1)
The PIO data cycle timing for a particular device can
be the timing value for the maximum PIO mode which
that device reports it supports.
2)
The PIO command cycle timing for a particular device
must be the timing value for the lowest PIO mode for
both devices on the channel.
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module
For example, if a channel had one Mode 4 device and one
Mode 0 device, then the Mode 4 device would have command timings for Mode 0 and data timing for Mode 4. The
Mode 0 device would have both command and data timings
for Mode 0. Note that for the Mode 0 case, the 32-bit timing
value is listed because both data and command timings are
the same mode. However, the actual timing value for the
Mode 4 device would be constructed out of the Mode 4
data timing 16-bit value and the Mode 0 16-bit command
timing value. Both 16-bit values are shown in the register
description but not assembled together as they are mixed
modes.
6.2.3.3 Bus Master Mode
Two IDE bus masters are provided to perform the data
transfers for the primary and secondary channels. The IDE
controller of the Core Logic module off-loads the CPU and
improves system performance in multitasking environments.
The bus master mode programming interface is an extension of the standard IDE programming model. This means
that devices can always be dealt with using the standard
IDE programming model, with the master mode functionality used when the appropriate driver and devices are
present. Master operation is designed to work with any IDE
device that supports DMA transfers on the IDE bus.
Devices that work in PIO mode can only use the standard
IDE programming model.
The IDE bus masters use a simple scatter/gather mechanism allowing large transfer blocks to be scattered to or
gathered from memory. This cuts down on the number of
interrupts to and interactions with the CPU.
Physical Region Descriptor Table Address
Before the controller starts a master transfer it is given a
pointer to a Physical Region Descriptor Table. This pointer
sets the starting memory location of the Physical Region
Descriptors (PRDs). The PRDs describe the areas of memory that are used in the data transfer. The PRDs must be
aligned on a 4-byte boundary and the table cannot cross a
64 KB boundary in memory.
Primary and Secondary IDE Bus Master Registers
The IDE Bus Master Registers for each channel (primary
and secondary) have an IDE Bus Master Command register and Bus Master Status register. These registers and bit
formats are described in Table 6-36 on page 277.
Physical Region Descriptor Format
Each physical memory region to be transferred is
described by a Physical Region Descriptor (PRD) as illustrated in Table 6-1. When the bus master is enabled (Command register bit 0 = 1), data transfer proceeds until each
PRD in the PRD table has been transferred. The bus master does not cache PRDs.
The PRD table consists of two DWORDs. The first DWORD
contains a 32-bit pointer to a buffer to be transferred. The
second DWORD contains the size (16 bits) of the buffer
and the EOT flag. The EOT bit (bit 31) must be set to indicate the last PRD in the PRD table.
Programming Model
The following steps explain how to initiate and maintain a
bus master transfer between memory and an IDE device.
1)
Software creates a PRD table in system memory.
Each PRD entry is 8 bytes long, consisting of a base
address pointer and buffer size. The maximum data
that can be transferred from a PRD entry is 64 KB. A
PRD table must be aligned on a 4-byte boundary. The
last PRD in a PRD table must have the EOT bit set.
2)
Software loads the starting address of the PRD table
by programming the PRD Table Address register.
3)
Software must fill the buffers pointed to by the PRDs
with IDE data.
4)
Write 1 to the Bus Master Interrupt bit and Bus Master
Error (Status register bits 2 and 1) to clear the bits.
5)
Set the correct direction to the Read or Write Control
bit (Command register bit 3).
Engage the bus master by writing a “1” to the Bus
Master Control bit (Command register bit 0).
The bus master reads the PRD entry pointed to by the
PRD Table Address register and increments the
address by 08h to point to the next PRD. The transfer
begins.
6)
The bus master transfers data to/from memory
responding to bus master requests from the IDE
device. At the completion of each PRD, the bus master’s next response depends on the settings of the
EOT flag in the PRD. If the EOT bit is set, then the IDE
bus master clears the Bus Master Active bit (Status
register bit 0) and stop. If any errors occurred during
the transfer, the bus master sets the Bus Master Error
bit Status register bit 1).
Table 6-1. Physical Region Descriptor Format
Byte 3
Byte 2
Byte 1
Byte 0
DWORD 31 31 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
0
1
E
O
T
8
7
6
5
4
3
2
1
0
Memory Region Physical Base Address [31:1] (IDE Data Buffer)
0
Reserved
0
AMD Geode™ SC3200 Processor Data Book
Size [15:1]
161
Revision 5.1
Core Logic Module
6.2.3.4 UltraDMA/33 Mode
The IDE controller of the Core Logic module supports
UltraDMA/33. It utilizes the standard IDE Bus Master functionality to interface, initiate and control the transfer.
UltraDMA/33 definition also incorporates a Cyclic Redundancy Checking (CRC) error checking protocol to detect
errors.
The UltraDMA/33 protocol requires no extra signal pins on
the IDE connector. The IDE controller redefines three standard IDE control signals when in UltraDMA/33 mode.
These definitions are shown in Table 6-2.
Table 6-2. UltraDMA/33 Signal Definitions
IDE Controller
Channel Signal
UltraDMA/33
Read Cycle
UltraDMA/33
Write Cycle
IDE_IOW#
STOP
STOP
IDE_IOR#
DMARDY#
STROBE
IDE_IORDY
STROBE
DMARDY#
All other signals on the IDE connector retain their functional definitions during the UltraDMA/33 operation.
IDE_IOW# is defined as STOP for both read and write
transfers to request to stop a transaction.
IDE_IOR# is redefined as DMARDY# for transferring data
from the IDE device to the IDE controller. It is used by the
IDE controller to signal when it is ready to transfer data and
to add wait states to the current transaction. IDE_IOR# signal is defined as STROBE for transferring data from the
IDE controller to the IDE device. It is the data strobe signal
driven by the IDE controller on which data is transferred
during each rising and falling edge transition.
IDE_IORDY is redefined as STROBE for transferring data
from the IDE device to the IDE controller during a read
cycle. It is the data strobe signal driven by the IDE device
on which data is transferred during each rising and falling
edge transition. IDE_IORDY is defined as DMARDY# during a write cycle for transferring data from the IDE controller to the IDE device. It is used by the IDE device to signal
when it is ready to transfer data and to add wait states to
the current transaction.
UltraDMA/33 data transfer consists of three phases, a startup phase, a data transfer phase and a burst termination
phase.
The IDE device begins the startup phase by asserting
IDE_DREQ. When ready to begin the transfer, the IDE controller asserts IDE_DACK#. When IDE_DACK# is asserted,
the IDE controller drives IDE_CS0# and IDE_CS1#
asserted, and IDE_ADDR[2:0] low. For write cycles, the
IDE controller negates STOP, waits for the IDE device to
assert DMARDY#, and then drives the first data WORD
and STROBE signal. For read cycles, the IDE controller
negates STOP, and asserts DMARDY#. The IDE device
then sends the first data WORD and asserts STROBE.
162
The data transfer phase continues the burst transfers with
the Core Logic and the IDE via providing data, toggling
STROBE and DMARDY#. The IDE_DATA[15:0] is latched
by receiver on each rising and falling edge of STROBE.
The transmitter can pause the burst cycle by holding
STROBE high or low, and resume the burst cycle by again
toggling STROBE. The receiver can pause the burst cycle
by negating DMARDY# and resumes the burst cycle by
asserting DMARDY#.
The current burst cycle can be terminated by either the
transmitter or the receiver. A burst cycle must first be
paused as described above before it can be terminated.
The IDE controller can then stop the burst cycle by asserting STOP, with the IDE device acknowledging by negating
IDE_DREQ. The IDE device then stops the burst cycle by
negating IDE_DREQ and the IDE controller acknowledges
by asserting STOP. The transmitter then drives the
STROBE signal to a high level. The IDE controller then
puts the result of the CRC calculation onto the
IDE_DATA[15:0] while de-asserting IDE_DACK#. The IDE
device latches the CRC value on the rising edge of
IDE_DACK#.
The CRC value is used for error checking on UltraDMA/33
transfers. The CRC value is calculated for all data by both
the IDE controller and the IDE device during the UltraDMA/
33 burst transfer cycles. This result of the CRC calculation
is defined as all data transferred with a valid STROBE edge
while IDE_DACK# is asserted. At the end of the burst
transfer, the IDE controller drives the result of the CRC calculation onto IDE_DATA[15:0] which is then strobed by the
de-assertion of IDE_DACK#. The IDE device compares the
CRC result of the IDE controller to its own and reports an
error if there is a mismatch.
The timings for UltraDMA/33 are programmed into the
DMA control registers:
• Channel 0 Drive 0 DMA Control Register (F2 Index 44h)
• Channel 0 Drive 1 DMA Control Register (F2 Index 4Ch)
• Channel 1 Drive 0 DMA Control Register (F2 Index 54h)
• Channel 1 Drive 1 DMA Control Register (F2 Index 5Ch)
The bit formats for these registers are described in Table 635 on page 273. Note that F2 Index 44h[20] is used to
select either Multiword or UltraDMA mode. Bit 20 = 0
selects Multiword DMA mode. If bit 20 = 1, then UltraDMA/
33 mode is selected. Once mode selection is made using
this bit, the remaining DMA Control registers also operate
in the selected mode.
Also listed in the bit formats are recommended values for
both Multiword DMA Modes 0-2 and UltraDMA/33 Modes
0-2. Note that these are only recommended settings and
are not 100% tested.
AMD Geode™ SC3200 Processor Data Book
Core Logic Module
6.2.4
Universal Serial Bus
The Core Logic module provides three complete, independent USB ports. Each port has a Data "Negative" and a
Data "Positive" signal.
The USB ports are Open Host Controller Interface (OpenHCI) compliant. The OpenHCI specification provides a register-level description for a host controller, as well as
common industry hardware/software interface and drivers.
6.2.5
Sub-ISA Bus Interface
The Sub-ISA interface of the Core Logic module is an ISAlike bus interface that is used by SC3200 to interface with
Boot Flash, M-Systems DiskOnChip or NAND EEPROM
and other I/O devices. The Core Logic module is the
default subtractive decoding agent and forwards all
unclaimed memory and I/O cycles to the ISA bus. However,
the Core Logic module can be configured to ignore either I/
O, memory, or all unclaimed cycles (subtractive decode
disabled).
Note:
The external Sub-ISA bus is a positive decode bus.
Unclaimed memory and I/O cycles will not appear
on the Sub-ISA interface.
Revision 5.1
• DOCW
— DOCW# is asserted on memory write transactions to
DOCCS# window (i.e., when both DOCCS# and
MEMW# are active, DOCW# is active; otherwise, it is
inactive).
• RD#, WR#
— The signals IOR#, IOW#, MEMR#, and MEMW# are
combined into two signals: RD# is asserted on I/O
read or memory read; WR# is asserted on I/O write
or memory write.
Memory devices that use ROMCS# or DOCCS# as their
chip select signal can be configured to support an 8-bit or
16-bit data bus via bits 3 and 6 of the MCR register. Such
devices can also be configured as zero wait states devices
(regardless of the data bus width) via bits 9 and 10 of the
MCR register. For MCR register bit descriptions, see Table
4-2 on page 88.
I/O peripherals that use IOCS0# or IOCS1# as their chip
select signal can be configured to support an 8-bit or 16-bit
data bus via bits 7 and 8 of the MCR register. Such devices
can also be configured as zero wait state devices (for 8-bit
peripherals) via bits 11 and 12 of the MCR register. For
MCR register bit descriptions, see Table 4-2 on page 88.
The Core Logic module does not support Sub-ISA refresh
cycles. The refresh toggle bit in Port B still exists for software compatibility reasons.
Other memory devices and I/O peripherals must be 8-bit
devices; their transactions can not be with zero wait states
The Sub-ISA interface includes the followings signals in
addition to the signals used for an ISA interface:
The Boot Flash supported by the SC3200 can be up to 16
MB. It is supported with the ROMCS# signal.
• IOCS0#/IOCS1#
— Asserted on I/O read/write transactions from/to a
programmable address range.
All unclaimed memory and I/O cycles are forwarded to the
Internal ISA bus if subtractive decode is enabled.
• DOCCS#
— Asserted on memory read/write transactions from/to
a programmable window.
• ROMCS#
— Asserted on memory read/write to upper 16 MB of
address space. Configurable via the ROM Mask
register (F0 Index 6Ch).
• DOCR#
— DOCR# is asserted on memory read transactions
from DOCCS# window (i.e., when both DOCCS# and
MEMR# are active, DOCR# is active; otherwise, it is
inactive).
AMD Geode™ SC3200 Processor Data Book
The DiskOnChip chip select signal (DOCCS#) is asserted
on any memory read or memory write transaction from/to a
programmable address range. The address range is programmable via the DOCCS# Base Address and Control
registers (F0 Index 78h and 7Ch). The base address must
be on an address boundary, the size of the range.
Signal DOCCS# can also be used to interface to NAND
Flash devices together with signals DOCW# and DOCR#.
See application note AMD Geode™ SC1200/SC2200/
SC3200 Processors: External NAND Flash Memory Circuit
for details.
163
Revision 5.1
Core Logic Module
6.2.5.1 Sub-ISA Bus Cycles
The ISA bus controller issues multiple ISA cycles to satisfy
PCI transactions that are larger than 16 bits. A full 32-bit
read or write results in two 16-bit ISA transactions or four 8bit ISA transactions. The ISA controller gathers the data
from multiple ISA read cycles and returns TRDY# to the
PCI bus.
SA[23:0] are a concatenation of ISA LA[23:17] and
SA[19:0] and perform equivalent functionality at a reduced
pin count.
Figure 6-2 shows the relationship between a PCI cycle and
the corresponding ISA cycle generated.
Note:
Not all signals described in Figure 6-2 are available externally. See Section 3.4.7 "Sub-ISA Interface Signals" on page 73 for more information
about which Sub-ISA signals are externally available on the SC3200.
6.2.5.2
Sub-ISA Support of Delayed PCI
Transactions
Multiple PCI cycles occur for every slower ISA cycle. This
prevents slow PCI cycles from occupying too much bandwidth and allows access to other PCI traffic. Figure 6-3 on
page 165 shows the relationship of PCI cycles to an ISA
cycle with PCI delayed transactions enabled.
Fast-PCI_CLK
ISACLK
FRAME#
IRDY#
TRDY#
STOP#
AD[31:0] (Read)
AD[31:0] (Write)
BALE
RD#,WR#,IOR#,IOW#
MEMR#,MEMW#
Figure 6-2. Non-Posted Fast-PCI to ISA Access
164
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module
REQ#
GNT#
FRAME#
Fast-PCI
1
2
1
IRDY#
1
TRDY#
STOP#
1
BALE
ISA
RD#, IOR#
3
1 - GX1 transaction
2 - IDE bus master - starts and completes
3 - End of ISA cycle
Figure 6-3. PCI to ISA Cycles with Delayed Transaction Enabled
6.2.5.3 Sub-ISA Bus Data Steering
The Core Logic module performs all of the required data
steering from SD[7:0] to SD[15:0] during normal 8-bit ISA
cycles, as well as during DMA and ISA master cycles. It
handles data transfers between the 32-bit PCI data bus
and the ISA bus. 8/16-bit devices can reside on the ISA
bus. Various PC-compatible I/O registers, DMA controller
registers, interrupt controller registers, and counter/timer
registers lie on the on-chip I/O data bus. Either the PCI bus
master or the DMA controllers can become the bus owner.
6.2.5.4 I/O Recovery Delays
In normal operation, the Core Logic module inserts a delay
between back-to-back ISA I/O cycles that originate on the
PCI bus. The default delay is four ISACLK cycles. Thus, the
second of consecutive I/O cycles is held in the ISA bus
controller until this delay count has expired. The delay is
measured between the rising edge of IOR#/IOW# and the
falling edge of BALE. This delay can be adjusted to a
greater delay through the ISA I/O Recovery Control register
(F0 Index 51h).
When the PCI bus master is the bus owner, the Core Logic
module data steering logic provides data conversion necessary for 8/16/32-bit transfers to and from 8/16-bit devices
on either the Sub-ISA bus or the 8-bit registers on the onchip I/O data bus. When PCI data bus drivers of the Core
Logic module are in TRI-STATE, data transfers between
the PCI bus master and PCI bus devices are handled
directly via the PCI data bus.
Note:
This delay is not inserted for a 16-bit Sub-ISA I/O
access that is split into two 8-bit I/O accesses.
When the DMA requestor is the bus owner, the Core Logic
module allows 8/16-bit data transfer between the Sub-ISA
bus and the PCI data bus.
AMD Geode™ SC3200 Processor Data Book
165
Revision 5.1
Core Logic Module
6.2.5.5 ISA DMA
DMA transfers occur between ISA I/O peripherals and system memory (i.e., not available externally). The data width
can be either 8 or 16 bits. Out of the seven DMA channels
available, four are used for 8-bit transfers while the remaining three are used for 16-bit transfers. One byte or WORD
is transferred in each DMA cycle.
Note:
The Core Logic module does not support DMA
transfers to ISA memory.
The ISA DMA device initiates a DMA request by asserting
one of the DRQ[7:5, 3:0] signals. When the Core Logic
module receives this request, it sends a bus grant request
to the PCI arbiter. After the PCI bus has been granted, the
respective DACK# is driven active.
The Core Logic module generates PCI memory read or
write cycles in response to a DMA cycle. Figure 6-4 and
Figure 6-5 are examples of DMA memory read and memory write cycles. Upon detection of the DMA controller’s
MEMR# or MEMW# active, the Core Logic module starts
the PCI cycle, asserts FRAME#, and negates an internal
IOCHRDY. This assures the DMA cycle does not complete
before the PCI cycle has provided or accepted the data.
IOCHRDY is internally asserted when IRDY# and TRDY#
are sampled active.
PCICLK
ISACLK
MEMR#
IOW#
SD[15:0]
IOCHRDY
FRAME#
AD[31:0]
IRDY#
TRDY#
Figure 6-4. ISA DMA Read from PCI Memory
PCICLK
ISACLK
MEMW#
IOR#
SD[15:0]
IOCHRDY
FRAME#
AD[31:0]
IRDY#
TRDY#
Figure 6-5. ISA DMA Write to PCI Memory
166
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module
6.2.5.6 ROM Interface
The Core Logic module positively decodes memory
addresses 000F0000h-000FFFFFh (64 KB) and
FFFC0000h-FFFFFFFFh (256 KB) at reset. These memory
cycles cause the Core Logic module to claim the cycle, and
generate an ISA bus memory cycle with ROMCS#
asserted. The Core Logic module can also be configured to
respond to memory addresses FF000000h-FFFFFFFFh
(16 MB) and 000E0000h-000FFFFFh (128 KB).
8- or 16-bit wide ROM is supported. BOOT16 strap determines the width after reset. MCR[14,3] (Offset 34h) in the
General Configuration Block (see Table 4-2 on page 88 for
bit details) allows program control of the width.
Flash ROM is supported in the Core Logic module by
enabling the ROMCS# signal on write accesses to the
ROM region. Normally only read cycles are passed to the
ISA bus, and the ROMCS# signal is suppressed for write
cycles. When the ROM Write Enable bit (F0 Index 52h[1])
is set, a write access to the ROM address region causes a
write cycle to occur with MEMW#, WR# and ROMCS#
asserted.
Table 6-3. Cycle Multiplexed PCI / Sub-ISA Balls
Ball No.
PCI
Sub-ISA
EBGA
TEPBGA
AD0
A0
A17
U1
AD1
A1
D16
P3
AD2
A2
A18
U3
AD3
A3
A15
N1
AD4
A4
A16
P1
AD5
A5
A14
N3
AD6
A6
C15
N2
AD7
A7
B14
M2
AD8
A8
C14
M4
AD9
A9
B13
L2
AD10
A10
C13
L3
AD11
A11
C12
K1
AD12
A12
A12
L4
AD13
A13
C11
J1
AD14
A14
A11
K4
AD15
A15
B10
J3
6.2.5.7 PCI and Sub-ISA Signal Cycle Multiplexing
The SC3200 multiplexes most PCI and Sub-ISA signals on
the balls listed in Table 6-3, in order to reduce the number
of balls on the device. Cycle multiplexing is on a bus-cycle
by bus-cycle basis (see Figure 6-6 on page 168), where
the internal Core Logic PCI bridge arbitrates between PCI
cycles and Sub-ISA cycles. Other PCI and Sub-ISA signals
remain non-shared, however, some Sub-ISA signals may
be muxed with GPIO.
AD16
A16
A7
E1
AD17
A17
C7
F4
AD18
A18
D7
E3
AD19
A19
A6
E2
AD20
A20
D6
D3
AD21
A21
C6
D1
AD22
A22
A5
D2
AD23
A23
F4
B6
Sub-ISA cycles are only generated as a result of GX1 module accesses to the following addresses or conditions:
AD24
D0
C5
C2
AD25
D1
D5
C4
• ROMCS# address range.
AD26
D2
A4
C1
AD27
D3
B4
D4
AD28
D4
C4
B4
• DOCCS# address range.
• IOCS0# address range.
AD29
D5
A3
B3
• IOCS1# address range.
AD30
D6
C2
A3
• An I/O write to address 80h or to 84h.
• Internal ISA is programmed to be the subtractive decode
agent and no other agents claim the cycle.
If the Sub-ISA and PCI bus have more than four components, the Sub-ISA components can be buffered using
74HCT245 or 74FCT245 type transceivers. The RD# (an
AND of IOR#, MEMR#) signal can be used as DIR control
while TRDE# is used as enable control.
AMD Geode™ SC3200 Processor Data Book
AD31
D7
B3
D5
C/BE0#
D8
A13
L1
C/BE1#
D9
A10
J2
C/BE2#
D10
D8
F3
C/BE3#
D11
A8
H4
PAR
D12
C10
J4
F1
TRDY#
D13
B8
IRDY#
D14
C8
F2
STOP#
D15
D9
G1
DEVSEL#
BHE#
B5
E4
167
Revision 5.1
Core Logic Module
PCI
TCS
Sub-ISA
TCP
PCI
pull-up
FRAME#
TRDY#, IRDY#
GNT[x]
ROMCS#, DOCCS#,
IOCS0#, IOCS1#
PAR,
DEVSEL#,STOP#
AD[31:0],
C/BE[3:0]#
Figure 6-6. PCI Change to Sub-ISA and Back
6.2.6
AT Compatibility Logic
The Core Logic module integrates:
• Two 8237-equivalent DMA controllers with full 32-bit
addressing
• Two 8259A-equivalent interrupt controllers providing 13
individually programmable external interrupts
• An 8254-equivalent timer for refresh, timer, and speaker
logic
• NMI control and generation for PCI system errors and all
parity errors
• Support for standard AT keyboard controllers
• Positive decode for the AT I/O register space
• Reset control
6.2.6.1 DMA Controller
The Core Logic module supports industry standard DMA
architecture using two 8237-compatible DMA controllers in
cascaded configuration. The DMA functions supported by
the Core Logic module include:
• Standard seven-channel DMA support (Channels 5
through 7 are not supported)
• 32-bit address range support via high page registers
• NMI control and generation for PCI system errors and all
parity errors.
Note:
DMA interface signals are not available externally.
DMA Channels
The Core Logic module supports seven DMA channels
using two standard 8237-equivalent controllers. DMA Controller 1 contains Channels 0 through 3 and supports 8-bit
I/O adapters. These channels are used to transfer data
between 8-bit peripherals and PCI memory or 8/16-bit ISA
memory. Using the high and low page address registers, a
full 32-bit PCI address is output for each channel so they
can all transfer data throughout the entire 4 GB system
address space. Each channel can transfer data in 64 KB
pages. Software initiated DMA requests are not supported.
DMA Controller 2 contains Channels 4 through 7. Channel
4 is used to cascade DMA Controller 1, so it is not available
externally. Channels 5 through 7 support 16-bit I/O adapters to transfer data between 16-bit I/O adapters and 16-bit
system memory. Using the high and low page address registers, a full 32-bit PCI address is output for each channel
so they can all transfer data throughout the entire 4 GB
system address space. Each channel can transfer data in
128 KB pages. Channels 5, 6, and 7 transfer 16-bit
WORDs on even byte boundaries only. Channels 5
through 7 are not supported.
• IOCHRDY extended cycles for compatible timing transfers
• Internal Sub-ISA bus master device support using
cascade mode
168
AMD Geode™ SC3200 Processor Data Book
Core Logic Module
DMA Transfer Modes
Each DMA channel can be programmed for single, block,
demand or cascade transfer modes. In the most commonly
used mode, single transfer mode, one DMA cycle occurs
per DRQ and the PCI bus is released after every cycle.
This allows the Core Logic module to timeshare the PCI
bus with the GX1 module. This is imperative, especially in
cases involving large data transfers, because the GX1
module gets locked out for too long.
In block transfer mode, the DMA controller executes all of
its transfers consecutively without releasing the PCI bus.
In demand transfer mode, DMA transfer cycles continue to
occur as long as DRQ is high or terminal count is not
reached. In this mode, the DMA controller continues to execute transfer cycles until the I/O device drops DRQ to indicate its inability to continue providing data. For this case,
the PCI bus is held by the Core Logic module until a break
in the transfers occurs.
In cascade mode, the channel is connected to another
DMA controller or to an ISA bus master, rather than to an I/
O device. In the Core Logic module, one of the 8237 controllers is designated as the master and the other as the
slave. The HOLD output of the slave is tied to the DRQ0
input of the master (Channel 4), and the master’s DACK0#
output is tied to the slave’s HLDA input.
In each of these modes, the DMA controller can be programmed for read, write, or verify transfers.
Both DMA controllers are reset at power-on reset (POR) to
fixed priority. Since master Channel 0 is actually connected
to the slave DMA controller, the slave’s four DMA channels
have the highest priority, with Channel 0 as highest and
Channel 3 as the lowest. Immediately following slave
Channel 3, master Channel 1 (Channel 5) is the next highest, followed by Channels 6 and 7.
DMA Controller Registers
The DMA controller can be programmed with standard I/O
cycles to the standard register space for DMA. The I/O
addresses for the DMA controller registers are listed Table
6-43 on page 313.
When writing to a channel's address or WORD Count register, the data is written into both the base register and the
current register simultaneously. When reading a channel
address or WORD Count register, only the current address
or WORD Count can be read. The base address and base
WORD Count are not accessible for reading.
DMA Transfer Types
Each of the seven DMA channels may be programmed to
perform one of three types of transfers: read, write, or verify. The transfer type selected defines the method used to
transfer a byte or WORD during one DMA bus cycle.
Revision 5.1
For write transfer types, the Core Logic module reads data
from the I/O device associated with the DMA channel and
write to the memory.
The verify transfer type causes the Core Logic module to
execute DMA transfer bus cycles, including generation of
memory addresses, but neither the READ nor WRITE command lines are activated. This transfer type was used by
DMA Channel 0 to implement DRAM refresh in the original
IBM PC and XT.
DMA Priority
The DMA controller may be programmed for two types of
priority schemes: fixed and rotate (I/O Ports 008h[4] and
0D0h[4] - see Table 6-43 on page 313).
In fixed priority, the channels are fixed in priority order
based on the descending values of their numbers. Thus,
Channel 0 has the highest priority. In rotate priority, the last
channel to get service becomes the lowest-priority channel
with the priority of the others rotating accordingly. This prevents a channel from dominating the system.
The address and WORD Count registers for each channel
are 16-bit registers. The value on the data bus is written
into the upper byte or lower byte, depending on the state of
the internal addressing byte pointer. This pointer can be
cleared by the Clear Byte Pointer command. After this command, the first read/write to an address or WORD-count
register reads or writes to the low byte of the 16-bit register
and the byte pointer points to the high byte. The next read/
write to an address or WORD-count register reads or
writes to the high byte of the 16-bit register and the byte
pointer points back to the low byte.
When programming the 16-bit channels (Channels 5, 6,
and 7), the address which is written to the base address
register must be the real address divided by two. Also, the
base WORD Count for the 16-bit channels is the number of
16-bit WORDs to be transferred, not the number of bytes
as is the case for the 8-bit channels.
The DMA controller allows the user to program the active
level (low or high) of the DRQ and DACK# signals. Since
the two controllers are cascaded together internally on the
chip, these signals should always be programmed with the
DRQ signal active high and the DACK# signal active low.
DMA Shadow Registers
The Core Logic module contains a shadow register located
at F0 Index B8h (Table 6-29 on page 206) for reading the
configuration of the DMA controllers. This read only register can sequence to read through all of the DMA registers.
For read transfer types, the Core Logic module reads data
from memory and write it to the I/O device associated with
the DMA channel.
AMD Geode™ SC3200 Processor Data Book
169
Revision 5.1
DMA Addressing Capability
DMA transfers occur over the entire 32-bit address range of
the PCI bus. This is accomplished by using the DMA controller’s 16-bit memory address registers in conjunction
with an 8-bit DMA Low Page register and an 8-bit DMA
High Page register. These registers, associated with each
channel, provide the 32-bit memory address capability. A
write to the Low Page register clears the High Page register, for backward compatibility with the PC/AT standard.
The starting address for the DMA transfer must be programmed into the DMA controller registers and the channel’s respective Low and High Page registers prior to
beginning the DMA transfer.
DMA Page Registers and Extended Addressing
The DMA Page registers provide the upper address bits
during DMA cycles. DMA addresses do not increment or
decrement across page boundaries. Page boundaries for
the 8-bit channels (Channels 0 through 3) are every 64 KB
and page boundaries for the 16-bit channels (Channels 5,
6, and 7) are every 128 KB.
Before any DMA operations are performed, the Page registers must be written at the I/O Port addresses in the DMA
controller registers to select the correct page for each DMA
channel. The other address locations between 080h and
08Fh and 480h and 48Fh are not used by the DMA channels, but can be read or written by a PCI bus master. These
registers are reset to zero at POR. A write to the Low Page
register clears the High Page register, for backward compatibility with the PC/AT standard.
For most DMA transfers, the High Page register is set to
zeros and is driven onto PCI address bits AD[31:24] during
DMA cycles. This mode is backward compatible with the
PC/AT standard. For DMA extended transfers, the High
Page register is programmed and the values are driven
onto the PCI addresses AD[31:24] during DMA cycles to
allow access to the full 4 GB PCI address space.
Core Logic Module
The lower address portion is generated directly by the DMA
controller during DMA operations. The lower address bits
are output on PCI address bits AD[7:0] for 8-bit channels
and AD[8:1] for 16-bit channels.
BHE# is configured as an output during all DMA operations. It is driven as the inversion of AD0 during 8-bit DMA
cycles and forced low for all 16-bit DMA cycles.
6.2.6.2 Programmable Interval Timer
The Core Logic module contains an 8254-equivalent Programmable Interval Timer (PIT) configured as shown in
Figure 6-7. The PIT has three timers/counters, each with
an input frequency of 1.19318 MHz (OSC divided by 12),
and individually programmable to different modes.
The gates of Counter 0 and 1 are usually enabled, however, they can be controlled via F0 Index 50h. The gate of
Counter 2 is connected to I/O Port 061h[0]. The output of
Counter 0 is connected internally to IRQ0. This timer is typically configured in Mode 3 (square wave output), and used
to generate IRQ0 at a periodic rate to be used as a system
timer function. The output of Counter 1 is connected to I/O
Port 061h[4]. The reset state of I/O Port 061h[4] is 0 and
every falling edge of Counter 1 output causes I/O Port
061h[4] to flip states. The output of Counter 2 is brought
out to the PC_BEEP output. This output is gated with I/O
Port 061h[1].
CLK0
1.19318 MHz
CLK2
F0 Index 50h[3]
GATE0
F0 Index 50h[5]
GATE1
I/O Port 061h[0]
GATE2
A[1:0]
DMA Address Generation
The DMA addresses are formed such that there is an
upper address, a middle address, and a lower address portion.
The upper address portion, which selects a specific page,
is generated by the Page registers. The Page registers for
each channel must be set up by the system before a DMA
operation. The DMA Page register values are driven on
PCI address bits AD[31:16] for 8-bit channels and
AD[31:17] for 16-bit channels.
The middle address portion, which selects a block within
the page, is generated by the DMA controller at the beginning of a DMA operation and any time the DMA address
increments or decrements through a block boundary. Block
sizes are 256 bytes for 8-bit channels (Channels 0 through
3) and 512 bytes for 16-bit channels (Channels 5, 6, and
7). The middle address bits are is driven on PCI address
bits AD[15:8] for 8-bit channels and AD[16:9] for 16-bit
channels.
170
OUT0
CLK1
IRQ0
F0 Index 50h[4]
I/O Port
061h[4]
OUT1
F0 Index 50h[6]
OUT2
PC_BEEP
I/O Port 061h[1]
XD[7:0]
IOW#
WR#
IOR#
RD#
Figure 6-7. PIT Timer
PIT Shadow Register
The PIT registers are shadowed to allow for 0V Suspend to
save/restore the PIT state by reading the PIT’s counter and
write only registers. The read sequence for the shadow
register is listed in F0 Index BAh (see Table 6-29 on page
206).
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module
6.2.6.3 Programmable Interrupt Controller
The Core Logic module contains two 8259A-equivalent
programmable interrupt controllers, with eight interrupt
request lines each, for a total of 16 interrupts. The PCI
device supports all x86 modes of operation except Special
Fully Nested mode. The two controllers are cascaded internally, and two of the interrupt request inputs are connected
to the internal circuitry. This allows a total of 13 externally
available interrupt requests. See Figure 6-9.
Each Core Logic IRQ signal can be individually selected to
as edge- or level-sensitive. The four PCI interrupt signals
may be routed internally to any PIC IRQ.
.
Table 6-4. PIC Interrupt Mapping
Master
IRQ
Mapping
IRQ0
Connected to the OUT0 (system timer) of
the internal 8254 PIT.
IRQ2
Connected to the slave’s INTR for a cascaded configuration.
IRQ8#
Connected to internal RTC.
IRQ13
Connected to the FPU interface of the
GX1 module.
IRQ15
Interrupts available to other functions
IRQ14
8254 Timer 0
IRQ0
IRQ1
IRQ2
IRQ3
IRQ4
IRQ5
IRQ6
IRQ7
IR0
IR1
IR2
IR3
IR4
IR5
IR6
IR7
IRQ12
Internal
INTR
IRQ11
IRQ10
IRQ9
IRQ7
IRQ6
RTC_IRQ#
FPU
IRQ8#
IRQ9
IRQ10
IRQ11
IRQ12
IRQ13
IRQ14
IRQ15
IR0
IR1
IR2
IR3
IR4
IR5
IR6
IR7
Figure 6-8. PIC Interrupt Controllers
Three interrupts are available externally depending upon
selected ball multiplexing:
1)
IRQ15 (muxed with GPIO11+RI2#),
2)
IRQ14 (muxed with TFTD1), and
3)
IRQ9 (muxed with IDE_DATA6)
IRQ5
IRQ4
IRQ3
IRQ1
The Core Logic module allows PCI interrupt signals INTA#,
INTB#, INTC# (muxed with GPIO19+IOCHRDY) and
INTD# (muxed with IDE_DATA7) to be routed internally to
any IRQ signal. The routing can be modified through Core
Logic module’s configuration registers. If this is done, the
IRQ input must be configured to be level- rather than edgesensitive. IRQ inputs may be individually programmed to be
level-sensitive with the Interrupt Sensitivity configuration
registers at I/O address space 4D0h and 4D1h. PCI interrupt configuration is discussed in further detail in “PCI
Compatible Interrupts” on page 172.
More of the IRQs are available through the use of SERIRQ
(muxed with GPIO39) function. See Table 6-4.
AMD Geode™ SC3200 Processor Data Book
171
Revision 5.1
PIC Interrupt Sequence
A typical AT-compatible interrupt sequence is as follows.
Any unmasked interrupt generates the internal INTR signal
to the CPU. The interrupt controller then responds to the
interrupt acknowledge (INTA) cycles from the CPU. On the
first INTA cycle the cascading priority is resolved to determine which of the two 8259A controllers output the interrupt vector onto the data bus. On the second INTA cycle
the appropriate 8259A controller drives the data bus with
the correct interrupt vector for the highest priority interrupt.
By default, the Core Logic module responds to PCI INTA
cycles because the system interrupt controller is located
within the Core Logic module. This may be disabled with
F0 Index 40h[0]. When the Core Logic module responds to
a PCI INTA cycle, it holds the PCI bus and internally generates the two INTA cycles to obtain the correct interrupt vector. It then asserts TRDY# and returns the interrupt vector.
Core Logic Module
PCI interrupts are low-level sensitive, whereas PC/AT interrupts are positive-edge sensitive; therefore, the PCI interrupts are inverted before being connected to the 8259A.
Although the controllers default to the PC/AT-compatible
mode (positive-edge sensitive), each IRQ may be individually programmed to be edge or level sensitive using the
Interrupt Edge/Level Sensitivity registers in I/O Port 4D0h
and 4D1h. However, if the controllers are programmed to
be level-sensitive via ICW1, all interrupts must be levelsensitive. Figure 6-9 shows the PCI interrupt mapping for
the master/slave 8259A interrupt controller.
IRQ[15:14,12:9,7:3,1]
Steering Registers
F0 Index 5Ch,5Dh
PIC I/O Registers
Each PIC contains registers located in the standard I/O
address locations, as shown in Table 6-46 "Programmable
Interrupt Controller Registers" on page 321.
An initialization sequence must be followed to program the
interrupt controllers. The sequence is started by writing Initialization Command Word 1 (ICW1). After ICW1 has been
written, the controller expects the next writes to follow in
the sequence ICW2, ICW3, and ICW4 if it is needed. The
Operation Control Words (OCW) can be written after initialization. The PIC must be programmed before operation
begins.
Since the controllers are operating in cascade mode, ICW3
of the master controller should be programmed with a
value indicating that the IRQ2 input of the master interrupt
controller is connected to the slave interrupt controller
rather than an I/O device as part of the system initialization
code. In addition, ICW3 of the slave interrupt controller
should be programmed with the value 02h (slave ID) and
corresponds to the input on the master controller.
PIC Shadow Register
The PIC registers are shadowed to allow for 0V Suspend to
save/restore the PIC state by reading the PICs write only
registers. A write to this register resets the read sequence
to the first register. The read sequence for the shadow register is listed in F0 Index B9h.
PCI Compatible Interrupts
The Core Logic module allows the PCI interrupt signals
INTA#, INTB#, INTC#, and INTD# (also known in industry
terms as PIRQx#) to be mapped internally to any IRQ signal with the PCI Interrupt Steering registers 1 and 2, F0
Index 5Ch and 5Dh.
172
PCI INTA#-INTD#
12
IRQ[13,8#,0]
4
Level/Edge
Sensitivity
3
12
4D0h/4D1h
ICW1
16
IRQ3
IRQ4
Master/Slave
8259A PIC
IRQ15
1
INTR
Figure 6-9. PCI and IRQ Interrupt Mapping
6.2.7
I/O Ports 092h and 061h System Control
The Core Logic module supports control functions of I/O
Ports 092h (Port A) and 061h (Port B) for PS/2 compatibility. I/O Port 092h allows a fast assertion of the A20M# or
CPU_RST. (CPU_RST is an internal signal that resets the
CPU. It is asserted for 100 µs after the negation of POR#.)
I/O Port 061h controls NMI generation and reports system
status.The Core Logic module generates an SMI for every
internal change of the A20M# state and the SMI handler
sets the A20M# state inside the GX1 module. This method
is used for both the Port 092h (PS/2) and Port 061h (keyboard) methods of controlling A20M#.
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module
6.2.7.1 I/O Port 092h System Control
I/O Port 092h allows for a fast keyboard assertion of an
A20# SMI and a fast keyboard CPU reset. Decoding for this
register may be disabled via F0 Index 52h[3].
The assertion of a fast keyboard A20# SMI is controlled by
either I/O Port 092h or by monitoring for the keyboard command sequence (see Section 6.2.8.1 "Fast Keyboard Gate
Address 20 and CPU Reset" on page 173). If bit 1 of I/O
Port 092h is cleared, the Core Logic module internally
asserts an A20M#, which in turn causes an SMI to the
GX1 module. If bit 1 is set, A20M# is internally deasserted, again causing an SMI.
The assertion of a fast keyboard reset (WM_RST SMI) is
controlled by bit 0 in I/O Port 092h or by monitoring for the
keyboard command sequence (write data = FEh to I/O port
64h). If bit 0 is changed from 0 to 1, the Core Logic module
generates a reset to the GX1 module by generating a
WM_RST SMI. When the WM_RST SMI occurs, the BIOS
jumps to the Warm Reset vector. Note that Warm Reset is
not a pin, it is under SMI control.
6.2.7.2 I/O Port 061h System Control
Through I/O Port 061h, the speaker output can be enabled,
the status of IOCHK# and SERR# can be read, and the
state of the speaker data (Timer2 output) and refresh toggle (Timer1 output) can be read back. Note that NMI is
under SMI control. Even though the hardware is present,
the IOCHK# ball does not exist. Therefore, an NMI from
IOCHK# can not happen.
6.2.8
Keyboard Support
The Core Logic module can actively decode the keyboard
controller I/O Ports 060h, 062h, 064h and 066h, and generate an LPC bus cycle. Keyboard positive decoding can be
disabled if F0 Index 5Ah[1] is cleared (i.e., subtractive
decoding enabled).
6.2.8.1
Fast Keyboard Gate Address 20 and CPU
Reset
The Core Logic module monitors the keyboard I/O Ports
064h and 060h for the fast keyboard A20M# and CPU reset
control sequences. If a write to I/O Port 060h[1] = 1 after a
write takes place to I/O Port 064h with data of D1h, then
the Core Logic module asserts the A20M# signal. A20M#
remains asserted until cleared by any one of the following:
• A write to bit 1 of I/O Port 092h.
• A CPU reset of some kind.
• A write to I/O Port 060h[1] = 0 following a write to I/O
Port 064h with data of D1h.
The fast keyboard A20M# and CPU reset can be disabled
through F0 Index 52h[7]. By default, bit 7 is set, and the
fast keyboard A20M# and CPU reset monitor logic is
active. If bit 7 is clear, the Core Logic module forwards the
commands to the keyboard controller.
By default, the Core Logic module forces the de-assertion
of A20M# during a warm reset. This action may be disabled if F0 Index 52h[4] is cleared.
6.2.7.3 SMI Generation for NMI
Figure 6-10 shows how the Core Logic module can generate an SMI for an NMI. Note that NMI is not a ball.
Parity Errors
AND
System Errors
F0 Index 04h[6]
I/O Port 061h[3]
F0 Index 04h[8]
AND
F0 Index 40h[1]
AND
IOCHK#
(No External Connection)
AND
NMI
SERR#
OR
PERR#
I/O Port 061h[2]
F0 Index 04h: PCI Command Register
Bit 6 = PE (PERR# Enable)
Bit 8 = SE (SERR# Enable)
AND
NMI
F0 Index 40h: PCI Function Control Register 1
Bit 1 = PES (PERR# Signals SERR#)
I/O Port 061h: Port B
Bit 2 = ERR_EN (PERR#/SERR# Enable)
Bit 3 = IOCHK_EN (IOCHK Enable)
OR
I/O Port 070h[7]
AND
SMI
I/O Port 070h: RTC Index Register (WO)
Bit 72 = NMI (NMI Enable)
Figure 6-10. SMI Generation for NMI
AMD Geode™ SC3200 Processor Data Book
173
Revision 5.1
6.2.9
Power Management Logic
The Core Logic module integrates advanced power management features including idle timers for common system
peripherals, address trap registers for programmable
address ranges for I/O or memory accesses, four programmable general purpose external inputs, clock throttling with
automatic speedup for the GX1 clock, software GX1 stop
clock, 0V Suspend/Resume with peripheral shadow registers, and a dedicated serial bus to/from the GX1 module
providing power management status.
The Core Logic module is ACPI (Advanced Configuration
Power Interface) compliant. An ACPI-compliant system is
one whose underlying BIOS, device drivers, chipset and
peripherals conform to revision 1.0 of the ACPI specification. The Core Logic also supports Advanced Power Management (APM).
The SC3200 provides the following support of ACPI states:
• CPU States: C0, C1, and C3.
• Sleep States:
— SL1/SL2 - ACPI S1 equivalent.
— SL3 - ACPI S3 equivalent.
— SL4 - ACPI S4 equivalent.
— SL5 - ACPI S5 equivalent.
• General Purpose Events: Fully programmable GPE0
Event Block registers.
• Wakeup Events: Supported through GPWIO[2:0] which
are powered by standby voltage and generate SMIs.
See registers at F1BAR1+I/O Offset 0Ah and
F1BAR1+I/O Offset 12h. Also see Section 5.6 "System
Wakeup Control (SWC)" on page 132 and Table 6-5
"Wakeup Events Capability" on page 175.
SC3200 device power management is highly tuned for low
power systems. It allows the system designer to implement
a wide range of power saving modes using a wide range of
capabilities and configuration options.
SC3200 controls the following functions directly:
• The system clocks.
• Core processor power states.
• Wakeup/resume event detection, including general
purpose events.
• Power supply and power planes.
Core Logic Module
6.2.9.1 CPU States
The SC3200 supports three CPU states: C0, C1 and C3
(the Core Logic C2 CPU state is not supported). These
states are fully compliant with the ACPI specification, revision 1.0. These states occur in the Working state only (S0/
G0). They have no meaning when the system transitions
into a Sleep state. For details on the various Sleep states,
see Section 6.2.9.2 "Sleep States" on page 175.
C0 Power State - On
In this state the GX1 module executes code. This state has
two sub-states: Full Speed or Throttling; selected via the
THT_EN bit (F1BAR1+I/O Offset 00h[4]).
C1 Power State - Active Idle
The SC3200 enters the C1 state, when the Halt Instruction
(HLT) is executed. It exits this state back to the C0 state
upon an NMI, an unmasked interrupt, or an SMI. The Halt
instruction stops program execution and generates a special Halt bus cycle. (See “Usage Hints” on page 177.)
Bus masters are supported in the C1 state and the SC3200
will temporarily exit C1 to perform a bus master transaction.
C2 Power State
The SC3200 does not support the C2 power state. All relevant registers and bit fields in the Core Logic are reserved.
C3 Power State
The SC3200 enters the C3 state, when the P_LVL3 register (F1BAR1+I/O Offset 05h) is read. It exits this state back
to the C0 state (Full Speed or Throttling, depending on the
THT_EN bit) upon:
• An NMI, an unmasked interrupt, or an SMI.
• A bus master request, if enabled via the BM_RLD bit
(F1BAR1+I/O Offset 0Ch[1]).
In this state, the GX1 module is in Suspend Refresh mode
(for details, see the Power Management section of the
AMD Geode™ GX1 Processor Data Book, and Section
6.2.9.5 "Usage Hints" on page 177).
PCI arbitration should be disabled prior entering the C3
state via the ARB_DIS bit in the PM2_CNT register
(F1BAR1+I/O Offset 20h[0]) because a PCI arbitration
event could start after P_LVL3 has been read. After
wakeup ARB_DIS needs to be cleared.
It also supports systems with an external micro controller
that is used as a power management controller.
174
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module
6.2.9.2 Sleep States
The SC3200 supports four Sleep states (SL1-SL3) and the
Soft Off state (G2/S5). These states are fully compliant
with the ACPI specification, revision 1.0.
When the SLP_EN bit (F1BAR1+I/O Offset 0Ch[13]) is set
to 1, the SC3200 enters an SLx state according to the
SLP_TYPx field (F1BAR1+I/O Offset 0Ch[12:10]). It exits
the Sleep state back to the S0 state (C0 state - Full Speed
or Throttling, depending on the THT_EN bit) upon an
enabled power management event. Table 6-5 on page 175
lists wakeup events from the various Sleep states.
SL1 Sleep State (ACPI S1)
In this state the core processor is in 3V Suspend mode (all
its clocks are stopped, including the memory controller and
the display controller). The SDRAM is placed in self-refresh
mode. All other SC3200 system clocks and PLLs are running. All devices are powered up (PWRCNT[2:1] and
ONCTL# are all asserted). See Section 6.2.9.5 "Usage
Hints" on page 177.
No reset is performed, when exiting this state. The SC3200
keeps all context in this state. This state corresponds to
ACPI Sleep state S1.
SL2 Sleep State (ACPI S1)
In this state, all of the SC3200 clocks are stopped including
the PLLs. Selected clocks from the PLLs can be kept running under program control (F0 Index 60h). An exception to
this is the CLK32 output signal which keeps toggling and
the 32 KHz oscillator itself. The SDRAM is placed in selfrefresh mode. The PWRCNT1 pin is de-asserted. The
SC3200 itself is powered up. The system designer can
decide which other system devices to power off with the
PWRCNT1 pin.
No reset is performed, when exiting this state. The SC3200
keeps all context in this state. This state corresponds to
ACPI sleep state S1, with lower power and longer wake
time than in SL1.
SL3 Sleep State (ACPI S3)
In this state, the SDRAM is placed in self-refresh mode,
and PWRCNT[2:1] are de-asserted. PWRCNT[2:1] should
be used to power off most of the system (except for the
SDRAM). If the Save-to-RAM feature is used, external circuitry in the SDRAM interface is required to guarantee data
integrity. All SC3200 signals powered by VSB, VSBL or
VBAT are still functional to allow wakeup and to keep the
RTC.
The power-up sequence is performed, when exiting this
state. This state corresponds to ACPI Sleep state S3.
SL4 and SL5 Sleep States (ACPI S4 and S5)
The SL4 and SL5 states are similar from the hardware perspective. In these states, the SC3200 de-asserts
PWRCNT[2:1] and ONCTL#. PWRCNT[2:1] and ONCTL#
should be used to power off the system. All signals powered by VSB, VSBL or VBAT are still functional to allow
wakeup and to keep the RTC.
While in this state, LED# can be toggled to give visual notification of this state. ACPI Function Control register
(F1BAR1+I/O Offset 07h[7:6]) is used to control LED#.
The power-up sequence is performed when exiting this
state. This state corresponds to ACPI Sleep states S4 and
S5.
Table 6-5. Wakeup Events Capability
Event
S0/C1
S0/C3
SL1
SL2
SL3
SL4, SL5
Enabled Interrupts
Yes
Yes
Yes
-
-
-
SMI according to Table 6-8
Yes
Yes
Yes
-
-
-
SCI according to Table 6-8
Yes
Yes
Yes
-
-
-
GPIO[47:32], GPIO[15:0]
Yes
Yes
Yes
-
-
-
Power Button
Yes
Yes
Yes
Yes
Yes
Yes
Power Button Override
Yes
Yes
Yes
Yes
Yes
Yes
Bus Master Request
Yes
1
Yes
Yes
-
-
-
Thermal Monitoring
Yes
Yes
Yes
Yes
Yes
Yes
USB
Yes
Yes
Yes
Yes
-
-
SDATA_IN2 (AC97)
Yes
Yes
Yes
Yes
-
-
IRRX1 (Infrared)
Yes
Yes
Yes
Yes
-
-
GPWIO[2:0]
Yes
Yes
Yes
Yes
Yes
Yes
RI2# (UART2)
Yes
Yes
Yes
Yes
-
-
RTC
Yes
Yes
Yes
Yes
Yes
Yes
1.
Temporarily exits state.
AMD Geode™ SC3200 Processor Data Book
175
Revision 5.1
Core Logic Module
6.2.9.3 Power Planes Control
The SC3200 supports up to three power planes. Three signals are used to control these power planes. Table 6-6
describes the signals and when each is asserted.
Table 6-6. Power Planes Control Signals vs.
Sleep States
S0
SL1
SL2
SL3
SL4
and
SL5
PWRCNT1
1
1
0
0
0
PWRCNT2
1
1
1
0
0
ONCTL#
0
0
0
0
1
Signal
These signals allow control of the power of system devices
and the SC3200 itself. Table 6-7 describes the SC3200
power planes with respect to the different Sleep and Global
states.
6.2.9.4 Power Management Events
The SC3200 supports power management events that can
manage:
• Transition of the system from a Sleep state to a Work
state. This is done by the hardware. These events are
defined as wakeup events.
• Enabled wakeup events to set the WAK_STS bit
(F1BAR1+I/O Offset 08h[15]) to 1, when transitioning
the system back to the working state.
• Generation of an interrupt. This invokes the relevant
software driver. The interrupt can either be an SMI or
SCI (selected by the SCI_EN bit, F1BAR1+I/O Offset
0Ch[0]). These events are defined as interrupt events.
Table 6-8 lists the power management events that can
generate an SCI or SMI.
Table 6-8. Power Management Events
Event
SCI
SMI
Power Button
Yes
Yes
Table 6-7. Power Planes vs. Sleep/Global States
Power Button Override
Yes
-
VCORE, VI/O,
Sleep/
VPLL
Global State
Bus Master Request
Yes
-
Thermal Monitoring
Yes
Yes
USB
Yes
Yes
RTC
Yes
Yes
ACPI Timer
Yes
Yes
VSB, VSBL
VBAT
On
On or Off
S0, SL1 and
SL2
On
SL3, SL4
and SL5
Off
On
On or Off
G3
Off
Off
On
No Power
Off
Off
Off
Illegal
On
Off
On or Off
The SC3200 power planes are controlled externally by the
three signals (i.e., the system designer should make sure
the system design is such that Table 6-7 is met) for all supported Sleep states.
GPIO
Yes
Yes
SDATA_IN2 (AC97)
Yes
Yes
IRRX1
Yes
Yes
RI2#
Yes
Yes
GPWIO
Yes
Yes
Internal SMI signal
Yes
-
VSB and VBAT are not controlled by any control signal. VSB
exists as long as the AC power is plugged in (for desktop
systems) or the main battery is charged (for mobile systems). VBAT exists as long as the RTC battery is charged.
The case in which VSB does not exist is called Mechanical
Off (G3).
176
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module
Power Button
The power button (PWRBTN#) input provides two events: a
wake request, and a sleep request. For both these events,
the PWRBTN# signal is debounced (i.e., the signal state is
transferred only after 14 to 16 ms without transitions, to
ensure that the signal is no longer bouncing).
ACPI is non-functional and all ACPI outputs are undefined
when the power-up sequence does not include using the
power button. SUSP# is an internal signal generated from
the ACPI block. Without an ACPI reset, SUSP# can be permanently asserted. If the USE_SUSP bit in CCR2 of GX1
module is enabled (Index C2h[7] = 1), the CPU will stop.
If ACPI functionality is desired, or the situation described
above avoided, the power button must be toggled. This can
be done externally or internally. GPIO63 is internally connected to PWRBTN#. To toggle the power button with software, GPIO63 must be programmed as an output using the
normal GPIO programming protocol (see Section 6.4.1.1
"GPIO Support Registers" on page 240). GPIO63 must be
pulsed low for at least 16 ms and not more than 4 sec.
Asserting POR# has no effect on ACPI. If POR# is
asserted and ACPI was active prior to POR#, then ACPI
will remain active after POR#. Therefore, BIOS must
ensure that ACPI is inactive before GPIO63 is pulsed low.
Power Button Wake Event - Detection of a high-to-low
transition on the debounced PWRBTN# input signal when
in SL1 to SL5 Sleep states. The system is considered in
the Sleep state, only after it actually transitioned into the
state and not only according to the SLP_TYP field.
In reaction to this event, the PWRBTN_STS bit (F1BAR1+I/
O Offset 08h[8]) is set to 1 and a wakeup event or an interrupt is generated (note that this is regardless of the
PWRBTN_EN bit, F1BAR1+I/O Offset 0Ah[8]).
Power Button Sleep Event - Detection of a high-to-low
transition on the debounced PWRBTN# input signal, when
in the Working state (S0).
In reaction to this event, the PWRBTN_STS bit is set to 1.
Power Button Override
When PWRBTN# is 0 for more than four seconds, ONCTL#
and PWRCNT[2:1] are de-asserted (i.e., the system transitions to the SL5 state, “Soft Off”). This power management
event is called the power button override event.
In reaction to this event, the PWRBTN_STS bit is cleared
to 0 and the PWRBTNOR_STS bit (F1BAR1+I/O Offset
08h[11]) is set to 1.
Thermal Monitoring
The thermal monitoring event (THRM#) enables control of
ACPI-OS Control.
When the THRM# signal transitions from high-to-low, the
THRM_STS bit (F1BAR1+I/O Offset 10h[5]) is set to 1. If
the THRM_EN bit (F1BAR1+I/O Offset 12h[5]) is also set
to 1, an interrupt is generated.
SDATA_IN2, IRRX1, RI2#
Section 5.4.1 "SIO Control and Configuration Registers" on
page 113 for control and operation.
6.2.9.5
Usage Hints
• During initialization, the BIOS should:
— Clear the SUSP_HLT bit in CCR2 (GX1 module,
Index C2h[3]) to 0. This is needed for compliance
with C0 definition of ACPI, when the Halt Instruction
(HLT) is executed.
— Disable the SUSP_3V option in C3 power state (F0
Index 60h[2]).
— Disable the SUSP_3V option in SL1 sleep state (F0
Index 60h[1]).
• SMM code should clear the CLK_STP bit in the PM
Clock Stop Control register (GX_BASE+Memory Offset
8500h[0]) to 0 when entering C3 state.
• SMM code should correctly set the CLK_STP bit in the
PM Clock Stop Control register (GX_BASE+Memory
Offset 8500h[0]) when entering the SL1, SL2, and SL3
states.
• When both the PWRBTN_STS bit and the
PWRBTN_EN bit are set to 1, an SCI interrupt is generated.
• When SCI_EN bit is 0, ONCTL# and PWRCNT[2:1] are
de-asserted immediately regardless of the
PWRBTN_EN bit.
AMD Geode™ SC3200 Processor Data Book
177
Revision 5.1
6.2.10
Power Management Programming
The power management resources provided by a combined GX1 module and Core Logic module based system
supports a high efficiency power management implementation. The following explanations pertain to a full-featured
“notebook” power management system. The extent to
which these resources are employed depends on the application and on the discretion of the system designer.
Power management resources can be grouped according
to the function they enable or support. The major functions
are as follows:
• APM Support
• CPU Power Management
— Suspend Modulation
— 3V Suspend
— Save-to-Disk
• Peripheral Power Management
— Device Idle Timers and Traps
— General Purpose Timers
— ACPI Timer Register
— Power Management SMI Status Reporting Registers
Included in the following subsections are details regarding
the registers used for configuring power management features. The majority of these registers are directly accessed
through the PCI configuration register space designated as
Function 0 (F0). However, included in the discussions are
references to F1BARx+I/O Offset xxh. This refers to registers accessed through base address registers in Function 1
(F1) at Index 10h (F1BAR0) and Index 40h (F1BAR1).
6.2.10.1 APM Support
Many notebook computers rely solely on an Advanced
Power Management (APM) driver for enabling the operating system to power-manage the CPU. APM provides several services which enhance the system power
management; but in its current form, APM is imperfect for
the following reasons:
• APM is an OS-specific driver, and may not be available
for some operating systems.
• Application support is inconsistent. Some applications in
foreground may prevent Idle calls.
• APM does not help with Suspend determination or
peripheral power management.
The Core Logic module provides two entry points for APM
support:
• Software CPU Suspend control via the CPU Suspend
Command register (F0 Index AEh)
• Software SMI entry via the Software SMI register (F0
Index D0h). This allows the APM BIOS to be part of the
SMI handler.
178
Core Logic Module
6.2.10.2 CPU Power Management
The three greatest power consumers in a system are the
display, the hard drive, and the CPU. The power management of the first two is relatively straightforward and is discussed
in Section 6.2.10.3
"Peripheral
Power
Management" on page 180.
APM, if available, is used primarily by CPU power management since the operating system is most capable of reporting the Idle condition. Additional resources provided by the
Core Logic module supplement APM by monitoring external activity and power managing the CPU based on the
system demands. The two processes for power managing
the CPU are Suspend Modulation and 3V Suspend.
Suspend Modulation
Suspend Modulation works by asserting and de-asserting
the internal SUSP# signal to the GX1 module for configurable durations. When SUSP# is asserted to the GX1
module, it enters an Idle state during which time the power
consumption is significantly reduced. Even though the PCI
clock is still running, the GX1 module stops the clocks to its
core when SUSP# is asserted. By modulating SUSP# a
reduced frequency of operation is achieved.
The Suspend Modulation feature works by assuming that
the GX1 module is Idle unless external activity indicates
otherwise. This approach effectively slows down the GX1
module until external activity indicates a need to run at full
speed, thereby reducing power consumption. This
approach is the opposite of that taken by most power management schemes in the industry, which run the system at
full speed until a period of inactivity is detected, and then
slows down. Suspend Modulation, the more aggressive
approach, yields lower power consumption.
Suspend Modulation serves as the primary CPU power
management mechanism when APM is not present. It also
acts as a backup for situations where APM does not correctly detect an Idle condition in the system.
To provide high-speed performance when needed, SUSP#
modulation is temporarily disabled any time system activity
is detected. When this happens, the GX1 module is
“instantly” converted to full speed for a programmed duration. System activities in the Core Logic module are
asserted as: any unmasked IRQ, accessing Port 061h, any
asserted SMI, and/or accessing the Video Processor module interface.
The graphics controller is integrated in the GX1 module.
Therefore, the indication of video activity is sent to the Core
Logic module via the serial link (see Section 6.2.2 "PSERIAL Interface" on page 159 for more information on serial
link) and is automatically decoded. Video activity is defined
as any access to the VGA register space, the VGA frame
buffer, the graphics accelerator control registers and the
configured graphics frame buffer.
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module
The automatic speedup events (video and IRQ) for Suspend Modulation should be used together with softwarecontrolled speedup registers for major I/O events such as
any access to the FDC, HDD, or parallel/serial ports, since
these are indications of major system activities. When
major I/O events occur, Suspend Modulation should be
temporarily disabled using the procedures described in the
Power Management registers in the following subsections.
If a bus master (UltraDMA/33, Audio, USB) request occurs,
the GX1 module automatically de-asserts SUSPA# and
grants the bus to the requesting bus master. When the bus
master de-asserts REQ#, SUSPA# reasserts. This does
not directly affect the Suspend Modulation programming.
Configuring Suspend Modulation: Control of the Suspend Modulation feature is accomplished using the Suspend Modulation and Suspend Configuration registers (F0
Index 94h and 96h, respectively).
The Suspend Configuration register contains the global
power management enable bit, as well as the enables for
the individual activity speedup timers. The global power
management bit must be enabled for Suspend Modulation
and all other power management resources to function.
Bit 0 of the Suspend Configuration register enables Suspend Modulation. Bit 1 controls how SMI events affect Suspend Modulation. In general this bit should be set to 1,
which causes SMIs to disable Suspend Modulation until it
is re-enabled by the SMI handler.
The Suspend Modulation register controls two 8-bit
counters that represent the number of 32 µs intervals that
the internal SUSP# signal is asserted and then deasserted to the GX1 module. These counters define a ratio
which is the effective frequency of operation of the system
while Suspend Modulation is enabled.
Asserted Count
Feff = FGX1 x Asserted Count + De-asserted Count
The IRQ and Video Speedup Timer Count registers (F0
Index 8Ch and 8Dh) configure the amount of time which
Suspend Modulation is disabled when the respective
events occur.
SMI Speedup Disable: If the Suspend Modulation feature
is being used for CPU power management, the occurrence
of an SMI disables Suspend Modulation so that the system
operates at full speed while in SMM. There are two methods used to invoke this via bit 1 of the Suspend Configuration register.
1)
If F0 Index 96h[1] = 0: Use the IRQ Speedup Timer
(F0 Index 8Ch) to temporarily disable Suspend Modulation when an SMI occurs.
2)
If F0 Index 96h[1] = 1: Disable Suspend Modulation
when an SMI occurs until a read to the SMI Speedup
Disable register (F1BAR0+I/O Offset 08h).
AMD Geode™ SC3200 Processor Data Book
The SMI Speedup Disable register prevents VSA software
from entering Suspend Modulation while operating in
SMM. The data read from this register can be ignored. If
the Suspend Modulation feature is disabled, reading this I/
O location has no effect.
3 Volt Suspend
The Core Logic module supports the stopping of the CPU
and system clocks for a 3V Suspend state. If appropriately
configured, via the Clock Stop Control register (F0 Index
BCh), the Core Logic module asserts internal SUSP_3V
after it has gone through the SUSP#/SUSPA# handshake.
SUSP_3V is a state indicator, indicating that the system is
in a low-activity state and Suspend Modulation is active.
This indicator can be used to put the system into a lowpower state (the system clock can be turned off).
Internal SUSP_3V is connected to the enable control of the
clock generators, so that the clocks to the CPU and the
Core Logic module (and most other system devices) are
stopped. The Core Logic module continues to decrement
all of its device timers and respond to external SMI interrupts after the input clock has been stopped, as long as the
32 KHz clock continues to oscillate. Any SMI event or
unmasked interrupt causes the Core Logic module to deassert SUSP_3V, restarting the system clocks. As the CPU
or other device might include a PLL, the Core Logic module
holds SUSP# active for a pre-programmed period of delay
(the PLL re-sync delay) that varies from 0 to 15 ms. After
this period has expired, the Core Logic module de-asserts
SUSP#, stopping Suspend. SMI# is held active for the
entire period, so that the CPU reenters SMM when the
clocks are restarted.
Save-to-Disk
Save-to-Disk is supported by the Core Logic module. In
this state, the power is typically removed from the Core
Logic module and from the entire SC3200, causing the
state of the legacy peripheral devices to be lost. Shadow
registers are provided for devices which allow their state to
be saved prior to removing power. This is necessary
because the legacy AT peripheral devices used several
write only registers. To restore the exact state of these
devices on resume, the write only register values are
“shadowed” so that the values can be saved by the power
management software.
The PC/AT compatible keyboard controller (KBC) and
floppy port (FDC) do not exist in the SC3200. However, it is
possible that one is attached on the ISA bus or the LPC
bus (e.g., in a SuperI/O device). Some of the KBC and FDC
registers are shadowed because they cannot be safely
read. Additional shadow registers for other functions are
described in Table 6-29 "F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support" on page 206.
179
Revision 5.1
6.2.10.3 Peripheral Power Management
The Core Logic module provides peripheral power management using a combination of device idle timers, address
traps, and general purpose I/O pins. Idle timers are used in
conjunction with traps to support powering down peripheral
devices.
Device Idle Timers and Traps
Idle timers are used to power manage a peripheral by
determining when the peripheral has been inactive for a
specified period of time, and removing power from the
peripheral at the end of that time period.
Idle timers are provided for the commonly-used peripherals
(FDC, IDE, Parallel/Serial Ports, and Mouse/Keyboard). In
addition, there are three user-defined timers that can be
configured for either I/O or memory ranges.
The idle timers are 16-bit countdown timers with a one second timebase or prescaler, providing a timeout range of 1
to 65536 seconds (1092 minutes) (18 hours). The input
clock is 32 KHz. Very small count values have some error
since the prescaler is free-running. (See the next subsection "General Purpose Timers" for further discussion on
prescaler value limitations.)
When the idle timer count registers are loaded with a nonzero value and enabled, the timers decrement until one of
two possibilities happens: a bus cycle occurs at that I/O or
memory range, or the timer decrements to zero.
If a bus cycle occurs, the timer is reloaded and begins decrementing again. If the timer decrements to zero, and
power management is enabled (F0 Index 80h[0] = 1), the
timer generates an SMI.
When an idle timer generates an SMI, the SMI handler
manages the peripheral power, disables the timer, and
enables the trap. The next time an event occurs, the trap
generates an SMI. This time, the SMI handler applies
power to the peripheral, resets the timer, and disables the
trap.
Relevant registers for controlling Device Idle Timers are: F0
Index 80h, 81h, 82h, 93h, 98h-9Eh, and ACh.
Relevant registers for controlling User Defined Device Idle
Timers are: F0 Index 81h, 82h, A0h, A2h, A4h, C0h, C4h,
C8h, CCh, CDh, and CEh.
Although not considered as device idle timers, two additional timers are provided by the Core Logic module. The
Video Idle Timer used for Suspend-determination and the
VGA Timer used for SoftVGA.
Core Logic Module
General Purpose Timers
The Core Logic module contains two general purpose idle
timers, General Purpose Timer 1 (F0 Index 88h) and General Purpose Timer 2 (F0 Index 8Ah). These two timers are
similar to the Device Idle Timers in that they count down to
zero unless re-triggered, and generate an SMI when they
reach zero. However, these are 8-bit timers instead of 16
bits, they have a programmable timebase, and the events
which reload these timers are configurable. These timers
are typically used for an indication of system inactivity for
Suspend determination.
General Purpose Timer 1 can be re-triggered by activity to
any of the configured User Defined Devices, Keyboard and
Mouse, Parallel and Serial, Floppy disk, or Hard disk.
General Purpose Timer 2 can be re-triggered by a transition on the GPIO7 signal (if GPIO7 is properly configured).
When a General Purpose Timer is enabled or when an
event reloads the timer, the timer is loaded with the configured count value. Upon expiration of the timer an SMI is
generated and a status flag is set. Once expired, this
counter must be re-initialized by disabling and enabling it.
The timebase or prescaler for both General Purpose Timers can be configured as either 1 second (default) or 1 millisecond. The 32 KHz clock feeds the prescaler. The
registers at F0 Index 89h and 8Bh are the control registers
for the General Purpose Timers.
The prescaler (1 millisecond or 1 second) that feeds the
timers is free-running; meaning that the first count decrement will not be correct. The decrement time can be as
short as 0 or as long as the prescaler. The actual time for
the decrement to occur can not be determined since the
current prescaler value can not be read. A periodic timer
can be achieved after the first timer SMI, because when
retriggered, the prescaler will be at or very nearly at the
maximum value. Any software using these timers must
understand this limitation. Small count values have the
most error with a value of 1having the largest error.
ACPI Timer Register
The ACPI Timer register (F1BAR0+I/O Offset 1Ch or at
F1BAR1+I/O Offset 1Ch) provides the ACPI counter. The
counter counts at 14.31818/4 MHz (3.579545 MHz). If SMI
generation is enabled (F0 Index 83h[5] = 1), an SMI or SCI
is generated when bit 23 toggles.
The programming bits for these timers are:
• F0 Index 81h[7], Video Access Idle Timer Enable
• F0 Index 82h[7], Video Access Trap Enable
• F0 Index A6h[15:0], Video Timer Count
• F0 Index 83h[3], VGA Timer Enable
• F0 Index 8Bh[6], VGA Timer Base
• F0 Index 8Eh[7:0], VGA Timer Count
180
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module
Power Management SMI Status Reporting Registers
The Core Logic module updates status registers to reflect
the SMI sources. Power management SMI sources are the
device idle timers, address traps, and general purpose I/O
pins.
Power management events are reported to the GX1 module through the active low SMI# signal. When an SMI is initiated, the SMI# signal is asserted low and is held low until
all SMI sources are cleared. At that time, SMI# is deasserted.
All SMI sources report to the Top Level SMI Status register
(F1BAR0+I/O Offset 02h) and the Top Level SMI Status
Mirror register (F1BAR0+I/O Offset 00h). The Top SMI Status and Status Mirror registers are the top level of hierarchy
for the SMI Handler in determining the source of an SMI.
SMI# Asserted
GX1
Module
Core Logic
Module
These two registers are identical except that reading the
register at F1BAR0+I/O Offset 02h clears the status.
Since all SMI sources report to the Top Level SMI Status
register, many of its bits combine a large number of events
requiring a second level of SMI status reporting. The second level of SMI status reporting is set up very much like
the top level. There are two status reporting registers, one
“read only” (mirror) and one “read to clear”. The data
returned by reading either offset is the same, the difference
between the two being that the SMI can not be cleared by
reading the mirror register.
Figure 6-11 on page 181 shows an example SMI tree for
checking and clearing the source of General Purpose Timers and the User Defined Trap generated SMI.
SMM software reads SMI Header
If Bit X = 1
(External SMI)
F1BAR0+I/O
Offset 02h
Read to Clear
to determine
top-level source
of SMI
Call internal SMI handler
to take appropriate action
SMI De-asserted after all SMI Sources are Cleared
(i.e., Top and Second Levels - note some sources may have a Third Level)
F1BAR0+I/O
Offset 06h
Read to Clear
to determine
second-level
source of SMI
Bits [15:10]
Other_SMI
Bit 9
GTMR_TRP_SMI
If Bit X = 0
(Internal SMI)
If bit 9 = 1,
Source of SMI
is GP Timer or UDEF Trap
Bits [15:6]
RSVD
Bit 5
PCI_TRP_SMI
Bit 4
UDEF3_TRP_SMI
Bit 3
UDEF2_TRP_SMI
Bits [8:0]
Other_SMI
Bit 2
UDEF1_TRP_SMI
Take
Appropriate
Action
Bit 1
GPT2_SMI
Bit 0
GPT1_SMI
Top Level
Second Level
Figure 6-11. General Purpose Timer and UDEF Trap SMI Tree Example
AMD Geode™ SC3200 Processor Data Book
181
Revision 5.1
Core Logic Module
6.2.10.4 Power Management Programming Summary
Table 6-9 provides a programming register summary for
the power management timers, traps, and functions. For
complete bit information regarding the registers listed in
Table 6-9, refer to Section 6.4.1 "Bridge, GPIO, and LPC
Registers - Function 0" on page 206.
Table 6-9. Device Power Management Programming Summary
Located at F0 Index xxh Unless Otherwise Noted
Device Power
Management Resource
Enable
Configuration
Second Level
SMI Status/No Clear
Second Level SMI
Status/With Clear
Global Timer Enable
80h[0]
N/A
N/A
N/A
Keyboard / Mouse Idle Timer
81h[3]
93h[1:0]
85h[3]
F5h[3]
Parallel / Serial Idle Timer
81h[2]
93h[1:0]
85h[2]
F5h[2]
Floppy Disk Idle Timer
81h[1]
9Ah[15:0], 93h[7]
85h[1]
F5h[1]
Video Idle Timer1
81h[7]
A6h[15:0]
85h[7]
F5h[7]
VGA Timer2
83h[3]
8Eh[7:0]
F1BAR0+I/O
Offset 00h[6]
F1BAR0+I/O
Offset 02h[6]
Primary Hard Disk Idle Timer
81h[0]
98h[15:0], 93h[5]
85h[0]
F5h[0]
Secondary Hard Disk Idle Timer
83h[7]
ACh[15:0], 93h[4]
86h[4]
F6h[4]
User Defined Device 1 Idle
Timer
81h[4]
A0h[15:0], C0h[31:0],
CCh[7:0]
85h[4]
F5h[4]
User Defined Device 2 Idle
Timer
81h[5]
A2h[15:0], C4h[31:0],
CDh[7:0]
85h[5]
F5h[5]
User Defined Device 3 Idle
Timer
81h[6]
A4h[15:0], C8h[31:0],
CEh[7:0]
85h[6]
F5h[6]
Global Trap Enable
80h[2]
N/A
N/A
N/A
Keyboard / Mouse Trap
82h[3]
9Eh[15:0] 93h[1:0]
86h[3]
F6h[3]
Parallel / Serial Trap
82h[2]
9Ch[15:0], 93h[1:0]
86h[2]
F6h[2]
Floppy Disk Trap
82h[1]
93h[7]
86h[1]
F6h[1]
Video Access Trap
82h[7]
N/A
86h[7]
F6h[7]
Primary Hard Disk Trap
82h[0]
93h[5]
86h[0]
F6h[0]
Secondary Hard Disk Trap
83h[6]
93h[4]
86h[5]
F6h[5]
User Defined Device 1 Trap
82h[4]
C0h[31:0], CCh[7:0]
F1BAR0+I/O
Offset 04h[2]
F1BAR0+I/O
Offset 06h[2]
User Defined Device 2 Trap
82h[5]
C4h[31:0], CDh[7:0]
F1BAR0+I/O
Offset 04h[3]
F1BAR0+I/O
Offset 06h[3]
User Defined Device 3 Trap
82h[6]
C8h[31:0], CEh[7:0]
F1BAR0+I/O
Offset 04h[4]
F1BAR0+I/O
Offset 06h[4]
General Purpose Timer 1
83h[0]
88h[7:0], 89h[7:0], 8Bh[4] F1BAR0+I/O
Offset 04h[0]
F1BAR0+I/O
Offset 06h[0]
General Purpose Timer 2
83h[1]
8Ah[7:0], 8Bh[5,3,2]
F1BAR0+I/O
Offset 04h[1]
F1BAR0+I/O
Offset 06h[1]
Suspend Modulation
96h[0]
94h[15:0], 96h[2:0]
N/A
N/A
Video Speedup
80h[4]
8Dh[7:0], A8h[15:0]
N/A
N/A
IRQ Speedup
80h[3]
8Ch[7:0]
N/A
N/A
1.
2.
182
This function is used for Suspend determination.
This function is used for SoftVGA.
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module
6.2.11
GPIO Interface
Up to 64 GPIOs in the in the Core Logic module are provided for system control. For further information, see Section 4.2 "Multiplexing, Interrupt Selection, and Base
Address Registers" on page 88 and Table 6-30
"F0BAR0+I/O Offset: GPIO Configuration Registers" on
page 240.
Note:
Not all GPIOs are available on SC3200 balls.
GPIOs [63:42], [31:21], and [5:2] are reserved.
6.2.12
• Trap accesses for MIDI UART interface at I/O Port 300h301h or 330h-331h.
• Trap accesses for serial input and output at COM2 (I/O
Port 2F8h-2FFh) or COM4 (I/O Port 2E8h-2EFh).
• Support trapping for low (I/O Port 00h-0Fh) and/or high
(I/O Port C0h-DFh) DMA accesses.
• Support hardware status register reads in Core Logic
module, minimizing SMI overhead.
• Support is provided for software-generated IRQs on IRQ
2, 3, 5, 7, 10, 11, 12, 13, 14, and 15.
Integrated Audio
The Core Logic module provides hardware support for the
Virtual (soft) Audio subsystem as part of the Virtual System
Architecture (VSA) technology for capture and playback
of audio using an external codec. This eliminates much of
the hardware traditionally associated with audio functions.
This hardware support includes:
The following subsections include details of the registers
used for configuring the audio interface. The registers are
accessed through F3 Index 10h, the Base Address Register (F3BAR0) in Function 3. F3BAR0 sets the base
address for the audio support registers as shown in Table
6-37 "F3: PCI Header Registers for Audio Configuration"
on page 279.
• Six-channel buffered PCI bus mastering interface.
• AC97 version 2.0 compatible interface to the codec. Any
codec, which supports an independent input and output
sample rate conversion interface, can be used with the
Core Logic module.
Additional hardware provides the necessary functionality
for VSA. This hardware includes the ability to:
• Generate an SMI to alert software to update required
data. An SMI is generated when either audio buffer is
half empty or full. If the buffers become completely
empty or full, the Empty bit is asserted.
6.2.12.1 Data Transport Hardware
The data transport hardware can be broadly divided into
two sections: bus mastering and the codec interface.
Audio Bus Masters
The Core Logic module audio hardware includes six PCI
bus masters (three for input and three for output) for transferring digitized audio between memory and the external
codec. With these bus master engines, the Core Logic
module off-loads the CPU and improves system performance.
• Trap accesses for sound card compatibility at either I/O
Port 220h-22Fh, 240h-24Fh, 260h-26Fh, or 280h-28Fh.
The programming interface defines a simple scatter/gather
mechanism allowing large transfer blocks to be scattered to
or gathered from memory. This cuts down on the number of
interrupts to and interactions with the CPU.
• Trap accesses for FM compatibility at I/O Port 388h38Bh.
The six bus masters that directly drive specific slots on the
AC97 interface are described in Table 6-10.
• Generate an SMI on I/O traps.
Table 6-10. Bus Masters That Drive Specific Slots of the AC97 Interface
Audio Bus
Master #
Slots
0
3 and 4
32-Bit output to codec. Left and right channels.
1
3 and 4
32-Bit input from codec. Left and right channels.
2
5
16-Bit output to codec.
3
5
16-Bit input from codec.
4
6 or 11
16-Bit output to codec. Slot in use is determined by F3BAR0+Memory Offset 08h[19].
5
6 or 11
16-Bit input from codec. Slot in use is determined by F3BAR0+Memory Offset 08h[20].
Description
AMD Geode™ SC3200 Processor Data Book
183
Revision 5.1
Core Logic Module
Physical Region Descriptor Table Address
Before the bus master starts a master transfer it must be programmed with a pointer (PRD Table Address register) to a
Physical Region Descriptor Table. This pointer sets the starting memory location of the Physical Region Descriptors
(PRDs). The PRDs describe the areas of memory that are
used in the data transfer. The descriptor table entries must be
aligned on a 32-byte boundary and the table cannot cross a
64 KB boundary in memory.
Physical Region Descriptor Format
Each physical memory region to be transferred is
described by a Physical Region Descriptor (PRD) as illustrated in Table 6-11. When the bus master is enabled
(Command register bit 0 = 1), data transfer proceeds until
each PRD in the PRD table has been transferred. The bus
master does not cache PRDs.
looping mechanism. If a PRD table is created with the
JMP bit set in the last PRD, the PRD table does not
need a PRD with the EOT bit set. A PRD can not have
both the JMP and EOT bits set.
Programming Model
The following discussion explains, in steps, how to initiate
and maintain a bus master transfer between memory and
an audio slave device.
In the steps listed below, the reference to “Example” refers
to Figure 6-12 "PRD Table Example" on page 185.
1)
The PRD table consists of two DWORDs. The first DWORD
contains a 32-bit pointer to a buffer to be transferred. The
second DWORD contains the size (16 bits) of the buffer
and flags (EOT, EOP, JMP). The description of the flags are
as follows:
• EOT bit - If set in a PRD, this bit indicates the last entry
in the PRD table (bit 31). The last entry in a PRD table
must have either the EOT bit or the JMP bit set. A PRD
can not have both the JMP and EOT bits set.
• EOP bit - If set in a PRD and the bus master has
completed the PRD’s transfer, the End of Page bit is set
(Status register bit 0 = 1) and an SMI is generated. If a
second EOP is reached due to the completion of
another PRD before the End of Page bit is cleared, the
Bus Master Error bit is set (Status register bit 1 = 1) and
the bus master pauses. In this paused condition, reading
the Status register clears both the Bus Master Error and
the End of Page bits and the bus master continues.
• JMP bit - This PRD is special. If set, the Memory Region
Physical Base Address is now the target address of the
JMP. The target address must be on a 32-byte boundary
so bits[4:0] must be written to 0. There is no data
transfer with this PRD. This PRD allows the creation of a
Software creates a PRD table in system memory.
Each PRD entry is 8 bytes long; consisting of a base
address pointer and buffer size. The maximum data
that can be transferred from a PRD entry is 64 KB. A
PRD table must be aligned on a 32-byte boundary.
The last PRD in a PRD table must have the EOT or
JMP bit set.
Example - Assume the data is outbound. There are
three PRDs in the example PRD table. The first two
PRDs (PRD_1, PRD_2) have only the EOP bit set.
The last PRD (PRD_3) has only the JMP bit set. This
example creates a PRD loop.
2)
Software loads the starting address of the PRD table
by programming the PRD Table Address register.
Example - Program the PRD Table Address register
with Address_3.
3)
Software must fill the buffers pointed to by the PRDs
with audio data. It is not absolutely necessary to fill the
buffers; however, the buffer filling process must stay
ahead of the buffer emptying. The simplest way to do
this is by using the EOP flags to generate an SMI
when a PRD is empty.
Example - Fill Audio Buffer_1 and Audio Buffer_2. The
SMI generated by the EOP from the first PRD allows
the software to refill Audio Buffer_1. The second SMI
refills Audio Buffer_2. The third SMI refills Audio
Buffer_1 and so on.
Table 6-11. Physical Region Descriptor Format
Byte 3
Byte 2
Byte 1
Byte 0
DWORD 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0
1
184
Memory Region Base Address [31:1] (Audio Data Buffer)
E E J
O O M
T P P
Reserved
Size [15:1]
0
0
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module
4)
Read the SMI Status register to clear the Bus Master
Error and End of Page bits (bits 1 and 0).
Set the correct direction to the Read or Write Control
bit (Command register bit 3). Note that the direction of
the data transfer of a particular bus master is fixed and
therefore the direction bit must be programmed
accordingly. It is assumed that the codec has been
properly programmed to receive the audio data.
Engage the bus master by writing a “1” to the Bus
Master Control bit (Command register bit 0).
The bus master reads the PRD entry pointed to by the
PRD Table Address register and increments the
address by 08h to point to the next PRD. The transfer
begins.
Example - The bus master is now properly programmed to transfer Audio Buffer_1 to a specific
slot(s) in the AC97 interface.
5)
The bus master transfers data to/from memory
responding to bus master requests from the AC97
interface. At the completion of each PRD, the bus master’s next response depends on the settings of the
flags in the PRD.
Example - At the completion of PRD_1 an SMI is generated because the EOP bit is set while the bus master continues on to PRD_2. The address in the PRD
Address_3
32-byte
boundary
Table Address register is incremented by 08h and is
now pointing to PRD_3. The SMI Status register is
read to clear the End of Page status flag. Since Audio
Buffer_1 is now empty, the software can refill it.
At the completion of PRD_2 an SMI is generated
because the EOP bit is set. The bus master then continues on to PRD_3. The address in the PRD Table
Address register is incremented by 08h. The DMA SMI
Status register is read to clear the End of Page status
flag. Since Audio Buffer_2 is now empty, the software
can refill it. Audio Buffer_1 has been refilled from the
previous SMI.
PRD_3 has the JMP bit set. This means the bus master uses the address stored in PRD_3 (Address_3) to
locate the next PRD. It does not use the address in the
PRD Table Address register to get the next PRD. Since
Address_3 is the location of PRD_1, the bus master
has looped the PRD table.
Stopping the bus master can be accomplished by not reading the SMI Status register End of Page status flag. This
leads to a second EOP which causes a Bus Master Error
and pauses the bus master. In effect, once a bus master
has been enabled it never has to be disabled, just paused.
The bus master cannot be disabled unless the bus master
has been paused or has reached an EOT.
Address_1
Address_1
PRD_1
EOT = 0
EOP = 1
JMP = 0
Audio
Buffer_1
Size_1
Audio
Buffer_2
Size_2
Size_1
Address_2
PRD_2
EOT = 0
EOP = 1
JMP = 0
Size_2
Address_2
Address_3
EOT = 0
EOP = 0
JMP = 1
PRD_3
Don’t Care
Figure 6-12. PRD Table Example
AMD Geode™ SC3200 Processor Data Book
185
Revision 5.1
6.2.12.2 AC97 Codec Interface
The AC97 codec (e.g., LM4548) is the master of the serial
interface and generates the clocks to Core Logic module.
Figure 6-13 shows the signal connections between two
codecs and the SC3200:
• Codec1 can be AC97 Rev. 1.3 or higher compliant.
• Codec2 is optional, but must be compliant with AC97 2.0
or higher. (For specifics on the serial interface, refer to
the appropriate codec manufacturer’s data book.)
— SDATA_IN2 has wakeup capability. (See Section 5.6
"System Wakeup Control (SWC)" on page 132.)
— If SDATA_IN2 is not used it must be connected to
VSS.
— If an AMC97 codec is used (as Codec2), it should be
connected to SDATA_IN2 and SDATA_IN should be
connected to VSS.
• For PC speaker synthesis, the Core Logic module
outputs the PC speaker signal on the PC_BEEP pin
which is connected to the PC_BEEP input of the AC97
codec. Note that PC_BEEP is muxed with GPIO16 and
must be programmed via PMR[0] (see Table 4-2 on
page 88.)
Core Logic Module
Codec Configuration/Control Registers
The codec 32-bit related registers:
• GPIO Status and Control Registers
— Codec GPIO Status Register (F3BAR0+Memory
Offset 00h)
— Codec GPIO Control Register (F3BAR0+Memory
Offset 04h)
• Codec Status Register (F3BAR0+Memory Offset 08h)
• Codec Command Register (F3BAR0+Memory Offset
0Ch)
Codec GPIO Status and Control Registers:
The Codec GPIO Status and Control registers are used for
codec GPIO related tasks such as enabling a codec GPIO
interrupt to cause an SMI.
Codec Status Register:
The Codec Status register stores the codec status WORD.
It is updated every valid Status Word slot.
Codec Command Register:
The Codec Command register writes the control WORD to
the codec. By writing the appropriate control WORDs to
this port, the features of the codec can be controlled. The
contents of this register are written to the codec during the
Control Word slot.
The bit formats for these registers are given in Table 6-38
"F3BAR0+Memory Offset: Audio Configuration Registers"
on page 280.
BIT_CLK
BIT_CLK
XTAL_I
SYNC
PC_BEEP
SDATA_OUT
SDATA_IN
SYNC
Codec1
PC_BEEP
SDATA_OUT
SDATA_IN
BIT_CLK
AC97_CLK
AMD Geode™
SC3200
Processor
XTAL_I
SYNC
Codec2
(Optional)
PC_BEEP
SDATA_OUT
SDATA_IN2
SDATA_IN2
Figure 6-13. AC97 V2.0 Codec Signal Connections
186
AMD Geode™ SC3200 Processor Data Book
Core Logic Module
Revision 5.1
6.2.12.3 VSA Technology Support Hardware
The Core Logic module incorporates the required hardware in order to support the Virtual System Architecture
(VSA) technology for capture and playback of audio using
an external codec. This eliminates much of the hardware
traditionally associated with industry standard audio functions.
Audio SMI Status Reporting Registers:
The Top SMI Status Mirror and Status registers are the top
level of hierarchy for the SMI Handler in determining the
source of an SMI. These two registers are at
F1BAR0+Memory Offset 00h (Status Mirror) and 02h (Status). The registers are identical except that reading the register at F1BAR0+Memory Offset 02h clears the status.
VSA Technology
VSA technology provides a framework to enable software
implementation of traditionally hardware-only components.
VSA software executes in System Management Mode
(SMM), enabling it to execute transparently to the operating
system, drivers and applications.
The second level of audio SMI status reporting is set up
very much like the top level. There are two status reporting
registers, one “read only” (mirror) and one “read to clear”.
The data returned by reading either offset is the same (i.e.,
SMI was caused by an audio related event). The difference
between F3BAR0+Memory Offset 10h (Status Mirror) and
12h (Status) is in the ability to clear the SMI source at 12h.
The VSA design is based upon a simple model for replacing hardware components with software. Hardware to be
virtualized is merely replaced with simple access detection
circuitry which asserts the SMI# (System Management
Interrupt) internal signal when hardware accesses are
detected. The current execution stream is immediately preempted, and the processor enters SMM. The SMM system
software then saves the processor state, initializes the VSA
execution environment, decodes the SMI source and dispatches handler routines which have registered requests to
service the decoded SMI source. Once all handler routines
have completed, the processor state is restored and normal execution resumes. In this manner, hardware accesses
are transparently replaced with the execution of SMM handler software.
Historically, SMM software was used primarily for the single
purpose of facilitating active power management for notebook designs. That software’s only function was to manage
the power up and down of devices to save power. With high
performance processors now available, it is feasible to
implement, primarily in SMM software, PC capabilities traditionally provided by hardware. In contrast to power management code, this virtualization software generally has
strict performance requirements to prevent application performance from being significantly impacted.
Audio SMI Related Registers
The SMI related registers consist of:
• Audio SMI Status Reporting Registers:
— Top Level SMI Mirror and Status Registers
(F1BAR0+Memory Offset 00h/02h)
— Second Level SMI Status Registers
(F3BAR0+Memory Offset 10h/12h)
• I/O Trap SMI and Fast Write Status Register
(F3BAR0+Memory Offset 14h)
• I/O Trap SMI Enable Register (F3BAR0+Memory Offset
18h)
AMD Geode™ SC3200 Processor Data Book
Figure 6-14 on page 188 shows an SMI tree for checking
and clearing the source of an audio SMI. Only the audio
SMI bit is detailed here. For details regarding the remaining
bits in the Top SMI Status Mirror and Status registers refer
toTable 6-33 "F1BAR0+I/O Offset: SMI Status Registers"
on page 253.
I/O Trap SMI and Fast Write Status Register:
This 32-bit read-only register (F3BAR0+Memory Offset
14h) not only indicates if the enabled I/O trap generated an
SMI, but also contains Fast Path Write related bits.
I/O Trap SMI Enable Register:
The I/O Trap SMI Enable register (F3BAR0+Memory Offset
18h) allows traps for specified I/O addresses and configures generation for I/O events. It also contains the enabling
bit for Fast Path Read/Write features.
Status Fast Path Read/Write
Status Fast Path Read – If enabled, the Core Logic module
intercepts and responds to reads to several status registers. This speeds up operations, and prevents SMI generation for reads to these registers. This process is called
Status Fast Path Read. Status Fast Path Read is enabled
via F3BAR0+Memory Offset 18h[4].
In Status Fast Path Read the Core Logic module responds
to reads of the following addresses:
388h-38Bh, 2x0h, 2x1h, 2x2h, 2x3h, 2x8h and 2x9h
Note that if neither sound card or FM I/O mapping is
enabled, then status read trapping is not possible.
Fast Path Write – If enabled, the Core Logic module captures certain writes to several I/O locations. This feature
prevents two SMIs from being asserted for write operations
that are known to take two accesses (the first access is an
index and the second is data). This process is called Fast
Path Write. Fast Path Write is enabled in via
F3BAR0+Memory Offset 18h[11].
Fast Path Write captures the data and address bit 1 (A1) of
the first access, but does not generate an SMI. A1 is stored
in F3BAR0+Memory Offset 14h[15]. The second access
causes an SMI, and the data and address are captured as
in a normal trapped I/O.
187
Revision 5.1
Core Logic Module
In Fast Path Write, the Core Logic module responds to
writes to the following addresses: 388h, 38Ah, 38Bh, 2x0h,
2x2h, and 2x8h.
SMI# Asserted
Table 6-38 on page 280 shows the bit formats of the second level SMI status reporting registers and the Fast Path
Read/Write programming bits.
SMM software reads SMI Header
If Bit X = 0
(Internal SMI)
If Bit X = 1
(External SMI)
GX1
Module
Call internal SMI handler
to take appropriate action
Core Logic Module
F1BAR0+Memory
Offset 02h
Read to Clear
to determine
top-level source
of SMI
SMI De-asserted after all SMI Sources are Cleared
(i.e., Top, Second, and Third Levels)
F3BAR0+Memory
Offset 10h
Read to Clear
to determine
second-level
source of SMI
Bits [15:8]
RSVD
Bit 7
ABM5_SMI
Bits [15:2]
Other_SMI
F3BAR0+Memory
Offset 14h
Read to Clear
to determine
third-level
source of SMI
Bit 6
ABM4_SMI
Bit 5
ABM3_SMI
Bit 1
AUDIO_SMI
Bit 0
Other_SMI
Top Level
If bit 1 = 1,
Source of
SMI is
Audio Event
Bit 4
ABM2_SMI
Take
Appropriate
Action
Bit 3
ABM1_SMI
Bit 2
ABM0_SMI
Bit 1
SER_INTR_SMI
Bit 0
I/O_TRAP_SMI
Bits [31:14]
Other_RO
Bit 13
SMI_SC/FM_TRAP
If bit 0 = 1,
Source of
SMI is
I/O Trap
Bit 12
SMI_DMA_TRAP
Bit 11
SMI_MPU_TRAP
Take
Appropriate
Action
Bit 10
SMI_SC/FM_TRAP
Second Level
Bits [9:0]
Other_RO
Third Level
Figure 6-14. Audio SMI Tree Example
188
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module
6.2.12.4 IRQ Configuration Registers
The Core Logic module provides the ability to set and clear
IRQs internally through software control. If the IRQs are
configured for software control, they do not respond to
external hardware. There are two registers provided for this
feature:
• Internal IRQ Enable Register (F3BAR0+Memory Offset
1Ah)
• Internal IRQ Control Register (F3BAR0+Memory Offset
1Ch)
Internal IRQ Enable Register
The Internal IRQ Enable register configures the IRQs as
internal (software) interrupts or external (hardware) interrupts. Any IRQ used as an internal software driven source
must be configured as internal.
Internal IRQ Control Register
The Internal IRQ Control register allows individual software
assertion/de-assertion of the IRQs that are enabled as
internal. These bits are used as masks when attempting to
write a particular IRQ bit. If the mask bit is set, it can then
be asserted/de-asserted according to the value in the loworder 16 bits. Otherwise the assertion/de-assertion values
of the particular IRQ can not be changed.
6.2.12.5 LPC Interface
The LPC interface of the Core Logic module is based on
the Intel® Low Pin Count (LPC) Interface specification,
revision 1.0. In addition to the requirement pins that are
specified in the Intel LPC Interface specification, the Core
Logic module also supports three optional pins: LDRQ#,
SERIRQ, and LPCPD#.
• Support desktop and mobile implementations.
• Enable support of a variable number of wait states.
• Enable I/O memory cycle retries in SMM handler.
• Enable support of wakeup and other power state transitions.
Assumptions and functionality requirements of the LPC
interface are:
• Only the following class of devices may be connected to
the LPC interface:
— SuperI/O (FDC, SP, PP, IR, KBC) - I/O slave, DMA,
bus master (for IR, PP).
— Audio, including AC97 style design - I/O slave, DMA,
bus master.
— Generic Memory, including BIOS - Memory slave.
— System Management Controller - I/O slave, bus
master.
• Interrupts are communicated with the serial interrupt
(SERIRQ) protocol.
• The LPC interface does not need to support high-speed
buses (such as CardBus, 1394, etc.) downstream, nor
does it need to support low-latency buses such as USB.
Figure 6-15 shows a typical setup. In this setup, the LPC is
connected through the Core Logic module to a PCI or host
bus.
ISA (Optional)
PCI/Host Bus
The following subsections briefly describe some sections of
the specification. However, for full details refer to the LPC
specification directly.
Core Logic
Module
The goals of the LPC interface are to:
• Enable a system without an ISA bus.
LPC
• Reduce the cost of traditional ISA bus devices.
• Use on a motherboard only.
• Perform the same cycle types as the ISA bus: memory, I/
O, DMA, and Bus Master.
• Increase the memory space from 16 MB to 4 GB to allow
BIOS sizes much greater.
• Provide synchronous design. Much of the challenge of
an ISA design is meeting the different, and in some
cases conflicting, ISA timings. Make the timings
synchronous to a reference well known to component
designers, such as PCI.
• Support software transparency: do not require special
drivers or configuration for this interface. The motherboard BIOS should be able to configure all devices at
boot.
AMD Geode™ SC3200 Processor Data Book
SuperI/O Module
KBC
SP
PP
FDC
Figure 6-15. Typical Setup
189
Revision 5.1
6.2.12.6 LPC Interface Signal Definitions
The LPC specification lists seven required and six optional
signals for supporting the LPC interface. Many of the signals are the same signals found on the PCI interface and
do not require any new pins on the host. Required signals
must be implemented by both hosts and peripherals.
Optional signals may or may not be present on particular
hosts or peripherals.
The Core Logic module incorporates all the required LPC
interface signals and two of the optional signals:
• Required LPC signals:
— LAD[3:0] - Multiplexed Command, Address and Data.
— LFRAME# - Frame: Indicates start of a new cycle,
termination of broken cycle.
— LRESET# - Reset: This signal is not available. Use
PCI Reset signal PCIRST# instead.
— LCLK - Clock: This signal is not available. Use PCI 33
MHz clock signal PCICLK instead.
• Core Logic module optional LPC signals:
— LDRQ# - Encoded DMA/Bus Master Request: Only
needed by peripheral that need DMA or bus
mastering. Peripherals may not share the LDRQ#
signal.
— SERIRQ - Serialized IRQ: Only needed by peripherals that need interrupt support.
— LPCPD# - Power Down: Indicates that the peripheral
should prepare for power to the LPC interface to be
shut down. Optional for the host.
Core Logic Module
6.2.12.7 Cycle Types
Table 6-12 shows the various types of cycles that are supported by the Core Logic module.
Table 6-12. Cycle Types
Supported Sizes
(Bytes)
Cycle Type
Memory Read
1
Memory Write
1
I/O Read
1
I/O Write
1
DMA Read
1 or 2
DMA Write
1 or 2
Bus Master Memory Read
1, 2, or 4
Bus Master Memory Write
1, 2, or 4
6.2.12.8 LPC Interface Support
The LPC interface supports all the features described in
the LPC Bus Interface specification, revision 1.0, with the
following exceptions:
• Only 8- or 16-bit DMA, depending on channel number.
Does not support the optional larger transfer sizes.
• Only one external DRQ pin.
190
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module - PCI Configuration Space and Access Methods
6.3
Register Descriptions
The Core Logic module is a multi-function module. Its register space can be broadly divided into three categories in
which specific types of registers are located:
1)
Chipset Register Space (F0-F5) (Note that F4 is for
Video Processor support, see Section 7.3.1 on page
345 for register descriptions): Comprised of six separate functions, each with its own register space, consisting of PCI header registers and configuration
registers.
The PCI header is a 256-byte region used for configuring a PCI device or function. The first 64 bytes are the
same for all PCI devices and are predefined by the
PCI specification. These registers are used to configure the PCI for the device. The rest of the 256-byte
region is used to configure the device or function itself.
2)
USB Controller Register Space (PCIUSB): Consists of
the standard PCI header registers. The USB controller
supports three ports and is OpenHCI compliant.
3)
ISA Legacy Register Space (I/O Ports): Contains all
the legacy compatibility I/O ports that are internal,
trapped, shadowed, or snooped.
6.3.1
PCI Configuration Space and Access
Methods
Configuration cycles are generated in the processor. All
configuration registers in the Core Logic module are
accessed through the PCI interface using the PCI Type
One Configuration Mechanism. This mechanism uses two
DWORD I/O locations at 0CF8h and 0CFCh. The first location (0CF8h) references the Configuration Address register.
The second location (0CFCh) references the Configuration
Data Register (CDR).
To access PCI configuration space, write the Configuration
Address (0CF8h) Register with data that specifies the Core
Logic module as the device on PCI being accessed, along
with the configuration register offset. On the following
cycle, a read or write to the Configuration Data Register
(CDR) causes a PCI configuration cycle to the Core Logic
module. Byte, WORD, or DWORD accesses are allowed to
CDR at 0CFCh, 0CFDh, 0CFEh, or 0CFFh.
The following subsections provide:
The Core Logic module has seven PCI configuration register sets, one for each function (F0-F5) and USB (PCIUSB).
Base Address Registers (BARx) in F0-F5 and PCIUSB set
the base addresses for additional I/O or memory mapped
configuration registers for each function.
• A brief discussion on how to access the registers
located in PCI Configuration Space.
Table 6-13 shows the PCI Configuration Address Register
(0CF8h) and how to access the PCI header registers.
• Core Logic module register summaries.
• Bit formats for Core Logic module registers.
Table 6-13. PCI Configuration Address Register (0CF8h)
31
30
24
23
16
15
11
10
8
7
2
1
0
Configuration
Space Mapping
Reserved
Bus Number
Device Number
Function
Index
DWORD
00
1 (Enable)
000 000
0000 0000
xxxx x (Note)
xxx
xxxx xx
00 (Always)
Function 0 (F0): Bridge Configuration, GPIO and LPC Configuration Register Space
80h
0000 0000
1001 0 or 1000 0
000
Index
001
Index
1001 0 or 1000 0
010
Index
1001 0 or 1000 0
011
Index
100
Index
1001 0 or 1000 0
101
Index
1001 1 or 1000 1
000
Index
Function 1 (F1): SMI Status and ACPI Timer Configuration Register Space
80h
0000 0000
1001 0 or 1000 0
Function 2 (F2): IDE Controller Configuration Register Space
80h
0000 0000
Function 3 (F3): Audio Configuration Register Space
80h
0000 0000
Function 4 (F4): Video Processor Configuration Register Space
80h
0000 0000
1001 0 or 1000 0
Function 5 (F5): X-Bus Expansion Configuration Register Space
80h
0000 0000
PCIUSB: USB Controller Configuration Register Space
80h
Note:
0000 0000
The device number depends upon the IDSEL Strap Override bit (F5BAR0+I/O Offset 04h[0]). This bit allows selection of the
address lines to be used as the IDSEL. By Default: IDSEL = AD28 (1001 0) for F0-F5, AD29 (1001 1) for PCIUSB.
AMD Geode™ SC3200 Processor Data Book
191
Revision 5.1
6.3.2
Core Logic Module - Register Summary
Register Summary
Note:
The tables in this subsection summarize the registers of
the Core Logic module. Included in the tables are the register’s reset values and page references where the bit formats are found.
Function 4 (F4) is for Video Processor support
(although accessed through the Core Logic PCI
configuration registers). Refer to Section 7.3.1
"Register Summary" on page 345 for details.
Table 6-14. F0: PCI Header/Bridge Configuration Registers
for GPIO and LPC Support Summary
Width
(Bits)
Type
00h-01h
16
02h-03h
16
F0 Index
Name
Reset
Value
Reference
(Table 6-29)
RO
Vendor Identification Register
100Bh
Page 206
RO
Device Identification Register
0500h
Page 206
04h-05h
16
R/W
PCI Command Register
000Fh
Page 206
06h-07h
16
R/W
PCI Status Register
0280h
Page 207
08h
8
RO
Device Revision ID Register
00h
Page 208
09h-0Bh
24
RO
PCI Class Code Register
0Ch
8
R/W
0Dh
8
R/W
060100h
Page 208
PCI Cache Line Size Register
00h
Page 208
PCI Latency Timer Register
00h
Page 208
0Eh
8
RO
PCI Header Type Register
80h
Page 208
0Fh
8
RO
PCI BIST Register
00h
Page 208
10h-13h
32
R/W
Base Address Register 0 (F0BAR0) — Sets the base address for
the I/O mapped GPIO Runtime and Configuration Registers (summarized in Table 6-15).
00000001h
Page 208
14h-17h
32
R/W
Base Address Register 1 (F0BAR1) — Sets the base address for
the I/O mapped LPC Configuration Registers (summarized in
Table 6-16)
00000001h
Page 208
18h-2Bh
---
---
Reserved
00h
Page 208
2Ch-2Dh
16
RO
Subsystem Vendor ID
100Bh
Page 208
2Eh-2Fh
16
RO
Subsystem ID
0500h
Page 208
30h-3Fh
---
---
Reserved
00h
Page 208
40h
8
R/W
PCI Function Control Register 1
39h
Page 209
41h
8
R/W
PCI Function Control Register 2
00h
Page 209
42h
---
---
Reserved
00h
Page 210
43h
8
R/W
PIT Delayed Transactions Register
02h
Page 210
44h
8
R/W
Page 210
45h
---
---
46h
8
47h
8
Reset Control Register
01h
Reserved
00h
Page 211
R/W
PCI Functions Enable Register
FEh
Page 211
R/W
Miscellaneous Enable Register
00h
Page 211
48h-4Bh
---
---
4Ch-4Fh
32
R/W
Reserved
Top of System Memory
00h
Page 211
FFFFFFFFh
Page 212
50h
8
R/W
PIT Control/ISA CLK Divider
7Bh
Page 212
51h
8
R/W
ISA I/O Recovery Control Register
40h
Page 212
52h
8
R/W
ROM/AT Logic Control Register
98h
Page 213
53h
8
R/W
Alternate CPU Support Register
00h
Page 213
54h-59h
---
---
Reserved
00h
Page 214
5Ah
8
R/W
Decode Control Register 1
01h
Page 214
5Bh
8
R/W
Decode Control Register 2
20h
Page 214
5Ch
8
R/W
PCI Interrupt Steering Register 1
00h
Page 215
5Dh
8
R/W
PCI Interrupt Steering Register 2
00h
Page 215
5Eh-5Fh
---
---
Reserved
00h
Page 215
60h-63h
32
R/W
00000000h
Page 216
64h-6Bh
---
---
00h
Page 216
192
ACPI Control Register
Reserved
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Register Summary
Revision 5.1
Table 6-14. F0: PCI Header/Bridge Configuration Registers
for GPIO and LPC Support Summary (Continued)
F0 Index
Width
(Bits)
Type
Name
6Ch-6Fh
32
R/W
ROM Mask Register
70h-71h
16
R/W
IOCS1# Base Address Register
72h
8
R/W
73h
8
---
74h-75h
16
R/W
IOCS0 Base Address Register
76h
8
R/W
IOCS0 Control Register
77h
---
---
78h-7Bh
32
R/W
7Ch-7Fh
32
80h
8
81h
8
82h
Reset
Value
Reference
(Table 6-29)
0000FFF0h
Page 216
0000h
Page 217
IOCS1# Control Register
00h
Page 217
Reserved
00h
Page 217
Reserved
0000h
Page 217
00h
Page 217
00h
Page 217
DOCCS Base Address Register
00000000h
Page 218
R/W
DOCCS Control Register
00000000h
Page 218
R/W
Power Management Enable Register 1
00h
Page 218
R/W
Power Management Enable Register 2
00h
Page 219
8
R/W
Power Management Enable Register 3
00h
Page 221
83h
8
R/W
Power Management Enable Register 4
00h
Page 222
84h
8
RO
Second Level PME/SMI Status Mirror Register 1
00h
Page 223
85h
8
RO
Second Level PME/SMI Status Mirror Register 2
00h
Page 224
86h
8
RO
Second Level PME/SMI Status Mirror Register 3
00h
Page 225
87h
8
RO
Second Level PME/SMI Status Mirror Register 4
00h
Page 226
88h
8
R/W
General Purpose Timer 1 Count Register
00h
Page 226
89h
8
R/W
General Purpose Timer 1 Control Register
00h
Page 227
8Ah
8
R/W
General Purpose Timer 2 Count Register
00h
Page 228
Page 228
8Bh
8
R/W
General Purpose Timer 2 Control Register
00h
8Ch
8
R/W
IRQ Speedup Timer Count Register
00h
Page 228
8Dh
8
R/W
Video Speedup Timer Count Register
00h
Page 228
8Eh
8
R/W
VGA Timer Count Register
00h
Page 229
8Fh-92h
---
---
93h
8
R/W
94h-95h
16
R/W
Suspend Modulation Register
96h
8
R/W
Suspend Configuration Register
Reserved
00h
Page 229
Miscellaneous Device Control Register
00h
Page 229
Reserved
0000h
Page 229
00h
Page 230
00h
Page 230
97h
---
---
98h-99h
16
R/W
Hard Disk Idle Timer Count Register — Primary Channel
0000h
Page 230
9Ah-9Bh
16
R/W
Floppy Disk Idle Timer Count Register
0000h
Page 230
9Ch-9Dh
16
R/W
Parallel / Serial Idle Timer Count Register
0000h
Page 230
9Eh-9Fh
16
R/W
Keyboard / Mouse Idle Timer Count Register
0000h
Page 231
A0h-A1h
16
R/W
User Defined Device 1 Idle Timer Count Register
0000h
Page 231
A2h-A3h
16
R/W
User Defined Device 2 Idle Timer Count Register
0000h
Page 231
A4h-A5h
16
R/W
User Defined Device 3 Idle Timer Count Register
0000h
Page 231
A6h-A7h
16
R/W
Video Idle Timer Count Register
0000h
Page 231
A8h-A9h
16
R/W
Video Overflow Count Register
0000h
Page 231
AAh-ABh
---
---
ACh-ADh
16
R/W
Reserved
Hard Disk Idle Timer Count Register — Secondary Channel
00h
Page 231
0000h
Page 232
AEh
8
WO
AFh
8
WO
CPU Suspend Command Register
00h
Page 232
Suspend Notebook Command Register
00h
B0h-B3h
---
Page 232
---
Reserved
00h
Page 232
B4h
8
RO
Floppy Port 3F2h Shadow Register
xxh
Page 232
B5h
8
RO
Floppy Port 3F7h Shadow Register
xxh
Page 232
B6h
8
RO
Floppy Port 1F2h Shadow Register
xxh
Page 232
B7h
8
RO
Floppy Port 1F7h Shadow Register
xxh
Page 232
AMD Geode™ SC3200 Processor Data Book
193
Revision 5.1
Core Logic Module - Register Summary
Table 6-14. F0: PCI Header/Bridge Configuration Registers
for GPIO and LPC Support Summary (Continued)
Width
(Bits)
Type
Reset
Value
Reference
(Table 6-29)
B8h
8
RO
B9h
8
RO
DMA Shadow Register
xxh
Page 233
PIC Shadow Register
xxh
BAh
8
Page 233
RO
PIT Shadow Register
xxh
BBh
Page 233
8
RO
RTC Index Shadow Register
xxh
Page 234
BCh
8
R/W
Clock Stop Control Register
00h
Page 234
BDh-BFh
---
---
Reserved
00h
Page 234
C0h-C3h
32
R/W
User Defined Device 1 Base Address Register
00000000h
Page 234
C4h-C7h
32
R/W
User Defined Device 2 Base Address Register
00000000h
Page 234
C8h-CBh
32
R/W
User Defined Device 3 Base Address Register
00000000h
Page 234
CCh
8
R/W
User Defined Device 1 Control Register
00h
Page 235
CDh
8
R/W
User Defined Device 2 Control Register
00h
Page 235
CEh
8
R/W
User Defined Device 3 Control Register
00h
Page 235
CFh
---
---
D0h
8
WO
D1h-EBh
16
---
ECh
8
R/W
EDh-F3h
---
---
Reserved
00h
Page 236
F4h
8
RC
Second Level PME/SMI Status Register 1
00h
Page 236
F5h
8
RC
Second Level PME/SMI Status Register 2
00h
Page 236
F6h
8
RC
Second Level PME/SMI Status Register 3
00h
Page 237
F7h
8
RC
Second Level PME/SMI Status Register 4
00h
Page 238
F8h-FFh
---
---
Reserved
00h
Page 239
F0 Index
194
Name
Reserved
00h
Page 235
Software SMI Register
00h
Page 235
Reserved
00h
Page 235
Timer Test Register
00h
Page 236
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Register Summary
Revision 5.1
Table 6-15. F0BAR0: GPIO Support Registers Summary
F0BAR0+
I/O Offset
00h-03h
Width
(Bits)
Type
Name
Reset
Value
Reference
(Table 6-30)
32
R/W
GPDO0 — GPIO Data Out 0 Register
FFFFFFFFh
Page 240
04h-07h
32
RO
GPDI0 — GPIO Data In 0 Register
FFFFFFFFh
Page 240
08h-0Bh
32
R/W
GPIEN0 — GPIO Interrupt Enable 0 Register
00000000h
Page 240
0Ch-0Fh
32
R/W1C
10h-13h
32
R/W
GPST0 — GPIO Status 0 Register
00000000h
Page 240
GPDO1 — GPIO Data Out 1 Register
FFFFFFFFh
Page 241
14h-17h
32
RO
GPDI1 — GPIO Data In 1 Register
FFFFFFFFh
Page 241
18h-1Bh
32
R/W
GPIEN1 — GPIO Interrupt Enable 1 Register
00000000h
Page 241
1Ch-1Fh
32
R/W1C
GPST1 — GPIO Status 1 Register
00000000h
Page 241
20h-23h
32
R/W
GPIO Signal Configuration Select Register
00000000h
Page 241
24h-27h
32
R/W
GPIO Signal Configuration Access Register
00000044h
Page 242
28h-2Bh
32
R/W
GPIO Reset Control Register
00000000h
Page 243
Reset
Value
Reference
(Table 6-31)
Table 6-16. F0BAR1: LPC Support Registers Summary
F0BAR1+
I/O Offset
Width
(Bits)
Type
Name
00h-03h
32
R/W
SERIRQ_SRC — Serial IRQ Source Register
00000000h
Page 244
04h-07h
32
R/W
SERIRQ_LVL — Serial IRQ Level Control Register
00000000h
Page 245
08h-0Bh
32
R/W
SERIRQ_CNT — Serial IRQ Control Register
00000000h
Page 247
0Ch-0Fh
32
R/W
DRQ_SRC — DRQ Source Register
00000000h
Page 247
10h-13h
32
R/W
LAD_EN — LPC Address Enable Register
00000000h
Page 248
14h-17h
32
R/W
LAD_D0 — LPC Address Decode 0 Register
00080020h
Page 249
18h-1Bh
32
R/W
LAD_D1 — LPC Address Decode 1 Register
00000000h
Page 250
1Ch-1Fh
32
R/W
LPC_ERR_SMI — LPC Error SMI Register
00000080h
Page 250
20h-23h
32
RO
LPC_ERR_ADD — LPC Error Address Register
00000000h
Page 251
AMD Geode™ SC3200 Processor Data Book
195
Revision 5.1
Core Logic Module - Register Summary
Table 6-17. F1: PCI Header Registers for SMI Status and ACPI Support Summary
F1 Index
00h-01h
Width
(Bits)
Type
16
RO
Name
Reset
Value
Reference
(Table 6-32)
Vendor Identification Register
100Bh
Page 252
Page 252
02h-03h
16
RO
Device Identification Register
0501h
04h-05h
16
R/W
PCI Command Register
0000h
Page 252
06h-07h
16
RO
PCI Status Register
0280h
Page 252
08h
8
RO
Device Revision ID Register
00h
Page 252
09h-0Bh
24
RO
PCI Class Code Register
068000h
Page 252
0Ch
8
RO
PCI Cache Line Size Register
00h
Page 252
0Dh
8
RO
PCI Latency Timer Register
00h
Page 252
0Eh
8
RO
PCI Header Type Register
00h
Page 252
00h
Page 252
00000001h
Page 252
0Fh
8
RO
PCI BIST Register
10h-13h
32
R/W
Base Address Register 0 (F1BAR0) — Sets the base address for
the I/O mapped SMI Status Registers (summarized in Table 6-18).
14h-2Bh
---
---
Reserved
00h
Page 252
2Ch-2Dh
16
RO
Subsystem Vendor ID
100Bh
Page 252
2Eh-2Fh
16
RO
Subsystem ID
0501h
Page 252
30h-3Fh
---
---
Reserved
00h
Page 252
40h-43h
32
R/W
00000001h
Page 252
44h-FFh
---
---
00h
Page 252
Name
Reset
Value
Reference
(Table 6-33)
Top Level PME/SMI Status Mirror Register
0000h
Page 253
Top Level PME/SMI Status Register
0000h
Page 254
Second Level General Traps & Timers PME/SMI Status Mirror
Register
0000h
Page 256
Base Address Register 1 (F1BAR1) — Sets the base address for
the I/O mapped ACPI Support Registers (summarized in Table 619)
Reserved
Table 6-18. F1BAR0: SMI Status Registers Summary
F1BAR0+
I/O Offset
Width
(Bits)
Type
00h-01h
16
RO
02h-03h
16
RO/RC
04h-05h
16
RO
06h-07h
16
RC
08h-09h
16
Read to
Enable
Second Level General Traps & Timers PME/SMI Status Register
0000h
Page 257
SMI Speedup Disable Register
0000h
Page 258
0Ah-1Bh
---
---
Reserved
1Ch-1Fh
32
RO
ACPI Timer Register
20h-21h
16
RO
Second Level ACPI PME/SMI Status Mirror Register
22h-23h
16
RC
Second Level ACPI PME/SMI Status Register
24h-27h
32
R/W
External SMI Register
28h-4Fh
---
---
Not Used
50h-FFh
---
---
The I/O mapped registers located here (F1BAR0+I/O Offset 50h-FFh) are also accessible at F0
Index 50h-FFh. The preferred method is to program these registers through the F0 register space.
196
00h
Page 258
xxxxxxxxh
Page 258
0000h
Page 258
0000h
Page 259
00000000h
Page 259
00h
Page 262
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Register Summary
Revision 5.1
Table 6-19. F1BAR1: ACPI Support Registers Summary
F1BAR1+
I/O Offset
Width
(Bits)
Type
Name
Reset
Value
Reference
(Table 6-34)
00h-03h
32
R/W
P_CNT — Processor Control Register
00000000h
Page 263
04h
8
RO
Reserved, do not read
00h
Page 263
05h
8
RO
P_LVL3 — Enter C3 Power State Register
xxh
Page 263
06h
8
R/W
SMI_CMD — OS/BIOS Requests Register
00h
Page 263
07h
8
R/W
ACPI_FUN_CNT — ACPI Function Control Register
00h
Page 263
08h-09h
16
R/W
PM1A_STS — PM1A Status Register
0000h
Page 264
0Ah-0Bh
16
R/W
PM1A_EN — PM1A Enable Register
0000h
Page 265
0Ch-0Dh
16
R/W
PM1A_CNT — PM1A Control Register
0000h
Page 265
0Eh
8
R/W
ACPI_BIOS_STS Register
00h
Page 266
0Fh
8
R/W
ACPI_BIOS_EN Register
00h
Page 267
10h-11h
16
R/W
GPE0_STS — General Purpose Event 0 Status Register
xxxxh
Page 267
12h-13h
16
R/W
GPE0_EN — General Purpose Event 0 Enable Register
0000h
Page 269
14h
8
R/W
GPWIO Control Register 1
00h
Page 270
15h
8
R/W
GPWIO Control Register 2
00h
Page 270
16h
8
R/W
GPWIO Data Register
00h
Page 271
17h
---
---
Reserved
00h
Page 271
18h-1Bh
32
R/W
ACPI SCI_ROUTING Register
00000F00h
Page 271
1Ch-1Fh
32
RO
PM_TMR — PM Timer Register
xxxxxxxxh
Page 272
20h
8
R/W
PM2_CNT — PM2 Control Register
00h
Page 272
21h-FFh
---
---
Not Used
00h
Page 272
AMD Geode™ SC3200 Processor Data Book
197
Revision 5.1
Core Logic Module - Register Summary
Table 6-20. F2: PCI Header Registers for IDE Controller Support Summary
F2 Index
00h-01h
Width
(Bits)
Type
16
RO
Name
Reset
Value
Reference
(Table 6-35)
Vendor Identification Register
100Bh
Page 273
Page 273
02h-03h
16
RO
Device Identification Register
0502h
04h-05h
16
R/W
PCI Command Register
0000h
Page 273
06h-07h
16
RO
PCI Status Register
0280h
Page 273
08h
8
RO
Device Revision ID Register
01h
Page 273
09h-0Bh
24
RO
PCI Class Code Register
010180h
Page 273
0Ch
8
RO
PCI Cache Line Size Register
00h
Page 273
0Dh
8
RO
PCI Latency Timer Register
00h
Page 273
0Eh
8
RO
PCI Header Type Register
00h
Page 273
0Fh
8
RO
PCI BIST Register
00h
Page 273
10h-13h
32
RO
Base Address Register 0 (F2BAR0) — Reserved for possible
future use by the Core Logic module.
00000000h
Page 273
14h-17h
32
RO
Base Address Register 1 (F2BAR1) — Reserved for possible
future use by the Core Logic module.
00000000h
Page 273
18h-1Bh
32
RO
Base Address Register 2 (F2BAR2) — Reserved for possible
future use by the Core Logic module.
00000000h
Page 273
1Ch-1Fh
32
RO
Base Address Register 3 (F2BAR3) — Reserved for possible
future use by the Core Logic module.
00000000h
Page 273
20h-23h
32
R/W
Base Address Register 4 (F2BAR4) — Sets the base address for
the I/O mapped Bus Master IDE Registers (summarized in Table
6-21)
00000001h
Page 273
24h-2Bh
---
---
Reserved
00h
Page 273
2Ch-2Dh
16
RO
Subsystem Vendor ID
100Bh
Page 273
2Eh-2Fh
16
RO
Subsystem ID
0502h
Page 273
30h-3Fh
---
---
Reserved
40h-43h
32
R/W
44h-47h
32
48h-4Bh
4Ch-4Fh
00h
Page 274
Channel 0 Drive 0 PIO Register
00009172h
Page 274
R/W
Channel 0 Drive 0 DMA Control Register
00077771h
Page 275
32
R/W
Channel 0 Drive 1 PIO Register
00009172h
Page 275
32
R/W
Channel 0 Drive 1 DMA Control Register
00077771h
Page 275
50h-53h
32
R/W
Channel 1 Drive 0 PIO Register
00009172h
Page 276
54h-57h
32
R/W
Channel 1 Drive 0 DMA Control Register
00077771h
Page 276
58h-5Bh
32
R/W
Channel 1 Drive 1 PIO Register
00009172h
Page 276
5Ch-5Fh
32
R/W
Channel 1 Drive 1 DMA Control Register
00077771h
Page 276
60h-FFh
---
---
00h
Page 276
198
Reserved
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module - Register Summary
Table 6-21. F2BAR4: IDE Controller Support Registers Summary
F2BAR4+
I/O Offset
Width
(Bits)
Type
00h
8
R/W
01h
---
---
02h
8
R/W
Name
IDE Bus Master 0 Command Register — Primary
Not Used
IDE Bus Master 0 Status Register — Primary
03h
---
---
04h-07h
32
R/W
Not Used
IDE Bus Master 0 PRD Table Address — Primary
08h
8
R/W
IDE Bus Master 1 Command Register — Secondary
09h
---
---
0Ah
8
R/W
0Bh
---
---
0Ch-0Fh
32
R/W
Not Used
IDE Bus Master 1 Status Register — Secondary
Not Used
IDE Bus Master 1 PRD Table Address — Secondary
Reset
Value
Reference
(Table 6-36)
00h
Page 277
---
Page 277
00h
Page 277
---
Page 277
00000000h
Page 277
00h
Page 278
---
Page 278
00h
Page 278
---
Page 278
00000000h
Page 278
Table 6-22. F3: PCI Header Registers for Audio Support Summary
F3 Index
00h-01h
Width
(Bits)
Type
16
RO
Name
Reset
Value
Reference
(Table 6-37)
Vendor Identification Register
100Bh
Page 279
Page 279
02h-03h
16
RO
Device Identification Register
0503h
04h-05h
16
R/W
PCI Command Register
0000h
Page 279
06h-07h
16
RO
PCI Status Register
0280h
Page 279
08h
8
RO
Device Revision ID Register
00h
Page 279
09h-0Bh
24
RO
PCI Class Code Register
040100h
Page 279
0Ch
8
RO
PCI Cache Line Size Register
00h
Page 279
0Dh
8
RO
PCI Latency Timer Register
00h
Page 279
0Eh
8
RO
PCI Header Type Register
00h
Page 279
00h
Page 279
00000000h
Page 279
0Fh
8
RO
PCI BIST Register
10h-13h
32
R/W
Base Address Register 0 (F3BAR0) — Sets the base address for
the memory mapped VSA audio interface control register block
(summarized in Table 6-23).
14h-2Bh
---
---
Reserved
00h
Page 279
2Ch-2Dh
16
RO
Subsystem Vendor ID
100Bh
Page 279
2Eh-2Fh
16
RO
Subsystem ID
0503h
Page 279
30h-FFh
---
---
Reserved
00h
Page 279
AMD Geode™ SC3200 Processor Data Book
199
Revision 5.1
Core Logic Module - Register Summary
Table 6-23. F3BAR0: Audio Support Registers Summary
F3BAR0+
Memory
Offset
Width
(Bits)
Type
Name
Reset
Value
Reference
(Table 6-38)
Page 280
00h-03h
32
R/W
Codec GPIO Status Register
00000000h
04h-07h
32
R/W
Codec GPIO Control Register
00000000h
Page 280
08h-0Bh
32
R/W
Codec Status Register
00000000h
Page 280
0Ch-0Fh
32
R/W
Codec Command Register
00000000h
Page 281
10h-11h
16
RC
Second Level Audio SMI Status Register
0000h
Page 281
12h-13h
16
RO
Second Level Audio SMI Status Mirror Register
0000h
Page 282
14h-17h
32
RO
I/O Trap SMI and Fast Write Status Register
00000000h
Page 283
18h-19h
16
R/W
I/O Trap SMI Enable Register
0000h
Page 284
1Ah-1Bh
16
R/W
Internal IRQ Enable Register
0000h
Page 285
1Ch-1Fh
32
R/W
Internal IRQ Control Register
00000000h
Page 286
20h
8
R/W
Audio Bus Master 0 Command Register
00h
Page 288
00h
Page 288
---
Page 288
21h
8
RC
Audio Bus Master 0 SMI Status Register
22h-23h
----
---
Not Used
24h-27h
32
R/W
Audio Bus Master 0 PRD Table Address
00000000h
Page 288
28h
8
R/W
Audio Bus Master 1 Command Register
00h
Page 289
29h
8
RC
Audio Bus Master 1 SMI Status Register
00h
Page 289
2Ah-2Bh
---
---
Not Used
---
Page 289
2Ch-2Fh
32
R/W
Audio Bus Master 1 PRD Table Address
00000000h
Page 289
30h
8
R/W
Audio Bus Master 2 Command Register
00h
Page 290
31h
8
RC
Audio Bus Master 2 SMI Status Register
00h
Page 290
32h-33h
---
---
Not Used
00h
Page 290
34h-37h
32
R/W
Audio Bus Master 2 PRD Table Address
00000000h
Page 290
38h
8
R/W
Audio Bus Master 3 Command Register
00h
Page 291
39h
8
RC
Audio Bus Master 3 SMI Status Register
00h
Page 291
3Ah-3Bh
---
---
Not Used
---
Page 291
3Ch-3Fh
32
R/W
Audio Bus Master 3 PRD Table Address
00000000h
Page 291
40h
8
R/W
Audio Bus Master 4 Command Register
00h
Page 292
41h
8
RC
Audio Bus Master 4 SMI Status Register
00h
Page 292
42h-43h
---
---
Not Used
---
Page 292
44h-47h
32
R/W
Audio Bus Master 4 PRD Table Address
00000000h
Page 292
48h
8
R/W
Audio Bus Master 5 Command Register
00h
Page 293
49h
8
RC
Audio Bus Master 5 SMI Status Register
00h
Page 293
4Ah-4Bh
---
---
Not Used
---
Page 293
4Ch-4Fh
32
R/W
00000000h
Page 293
200
Audio Bus Master 5 PRD Table Address
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Register Summary
Revision 5.1
Table 6-24. F5: PCI Header Registers for X-Bus Expansion Support Summary
F5 Index
00h-01h
Width
(Bits)
Type
16
RO
Name
Reset
Value
Reference
(Table 6-39)
Vendor Identification Register
100Bh
Page 294
Page 294
02h-03h
16
RO
Device Identification Register
0505h
04h-05h
16
R/W
PCI Command Register
0000h
Page 294
06h-07h
16
RO
PCI Status Register
0280h
Page 294
08h
8
RO
Device Revision ID Register
00h
Page 294
09h-0Bh
24
RO
PCI Class Code Register
068000h
Page 294
0Ch
8
RO
PCI Cache Line Size Register
00h
Page 294
0Dh
8
RO
PCI Latency Timer Register
00h
Page 294
0Eh
8
RO
PCI Header Type Register
00h
Page 294
0Fh
8
RO
PCI BIST Register
00h
Page 294
10h-13h
32
R/W
Base Address Register 0 (F5BAR0) — Sets the base address for
the X-Bus Expansion support registers (summarized in
Table 6-25.)
00000000h
Page 294
14h-17h
32
R/W
Base Address Register 1 (F5BAR1) — Reserved for possible
future use by the Core Logic module.
00000000h
Page 294
18h-1Bh
32
R/W
Base Address Register 2 (F5BAR2) — Reserved for possible
future use by the Core Logic module.
00000000h
Page 294
1Ch-1Fh
32
R/W
Base Address Register 3 (F5BAR3) — Reserved for possible
future use by the Core Logic module.
00000000h
Page 295
20h-23h
32
R/W
Base Address Register 4 (F5BAR4) — Reserved for possible
future use by the Core Logic module.
00000000h
Page 295
24h-27h
32
R/W
Base Address Register 5 (F5BAR5) — Reserved for possible
future use by the Core Logic module.
00000000h
Page 295
28h-2Bh
---
---
Reserved
00h
Page 295
2Ch-2Dh
16
RO
Subsystem Vendor ID
100Bh
Page 295
2Eh-2Fh
16
RO
Subsystem ID
0505h
Page 295
Reserved
30h-3Fh
---
---
40h-43h
32
R/W
00h
Page 295
F5BAR0 Base Address Register Mask
FFFFFFC1h
Page 295
44h-47h
32
R/W
F5BAR1 Base Address Register Mask
00000000h
Page 296
48h-4Bh
32
R/W
F5BAR2 Base Address Register Mask
00000000h
Page 296
4Ch-4Fh
32
R/W
F5BAR3 Base Address Register Mask
00000000h
Page 296
50h-53h
32
R/W
F5BAR4 Base Address Register Mask
00000000h
Page 296
54h-57h
32
R/W
F5BAR5 Base Address Register Mask
00000000h
Page 296
58h
8
R/W
F5BARx Initialized Register
00h
Page 296
xxh
Page 296
59h-FFh
---
---
60h-63h
32
R/W
Reserved
Scratchpad for Chip Number
00000000h
Page 296
64h-67h
32
R/W
Scratchpad for Configuration Block Address
00000000h
Page 297
68h-FFh
---
---
00h
Page 297
Reset
Value
Reference
(Table 6-40)
Reserved
Table 6-25. F5BAR0: I/O Control Support Registers Summary
F5BAR0+
I/O Offset
Width
(Bits)
Type
Name
00h-03h
32
R/W
I/O Control Register 1
010C0007h
Page 298
04h-07h
32
R/W
I/O Control Register 2
00000002h
Page 299
08h-0Bh
32
R/W
I/O Control Register 3
00009000h
Page 299
AMD Geode™ SC3200 Processor Data Book
201
Revision 5.1
Core Logic Module - Register Summary
Table 6-26. PCIUSB: USB PCI Configuration Register Summary
PCIUSB
Index
Width
(Bits)
Type
Name
Reset Value
Reference
(Table 6-41)
00h-01h
16
RO
Vendor Identification
0E11h
Page 300
02h-03h
16
RO
Device Identification
A0F8h
Page 300
04h-05h
16
R/W
Command Register
00h
Page 300
06h-07h
16
R/W
Status Register
0280h
Page 301
08h
8
RO
Device Revision ID
08h
Page 301
09h-0Bh
24
RO
Class Code
0Ch
8
R/W
0Dh
8
0Eh
0Fh
0C0310h
Page 301
Cache Line Size
00h
Page 301
R/W
Latency Timer
00h
Page 301
8
RO
Header Type
00h
Page 301
8
RO
BIST Register
00h
Page 301
10h-13h
32
R/W
Base Address 0
14h-2Bh
---
---
Reserved
00000000h
Page 301
00h
Page 302
Page 302
2Ch-2Dh
16
RO
Subsystem Vendor ID
0E11h
2Eh-2Fh
16
RO
Subsystem ID
A0F8h
Page 302
30h-3Bh
---
---
Reserved
00h
Page 302
3Ch
8
R/W
Interrupt Line Register
00h
Page 302
3Dh
8
R/W
Interrupt Pin Register
01h
Page 302
3Eh
8
RO
Min. Grant Register
00h
Page 302
3Fh
8
RO
Max. Latency Register
50h
Page 302
40h-43h
32
R/W
ASIC Test Mode Enable Register
000F0000h
Page 302
44h
8
R/W
ASIC Operational Mode Enable
00h
Page 302
45h-FFh
---
---
Reserved
00h
Page 302
202
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Register Summary
Revision 5.1
Table 6-27. USB_BAR: USB Controller Registers Summary
USB_BAR0
+Memory
Offset
Width
(Bits)
Type
Name
Reset Value
Reference
(Table 6-42)
Page 303
00h-03h
32
R/W
HcRevision
00000110h
04h-07h
32
R/W
HcControl
00000000h
Page 303
08h-0Bh
32
R/W
HcCommandStatus
00000000h
Page 303
0Ch-0Fh
32
R/W
HcInterruptStatus
00000000h
Page 303
10h-13h
32
R/W
HcInterruptEnable
00000000h
Page 304
14h-17h
32
R/W
HcInterruptDisable
00000000h
Page 304
18h-1Bh
32
R/W
HcHCCA
00000000h
Page 305
1Ch-1Fh
32
R/W
HcPeriodCurrentED
00000000h
Page 305
20h-23h
32
R/W
HcControlHeadED
00000000h
Page 305
24h-27h
32
R/W
HcControlCurrentED
00000000h
Page 305
28h-2Bh
32
R/W
HcBulkHeadED
00000000h
Page 305
2Ch-2Fh
32
R/W
HcBulkCurrentED
00000000h
Page 305
30h-33h
32
R/W
HcDoneHead
00000000h
Page 305
34h-37h
32
R/W
HcFmInterval
00002EDFh
Page 306
38h-3Bh
32
RO
HcFrameRemaining
00000000h
Page 306
3Ch-3Fh
32
RO
HcFmNumber
00000000h
Page 306
40h-43h
32
R/W
HcPeriodicStart
00000000h
Page 306
44h-47h
32
R/W
HcLSThreshold
00000628h
Page 306
48h-4Bh
32
R/W
HcRhDescriptorA
01000003h
Page 306
4Ch-4Fh
32
R/W
HcRhDescriptorB
00000000h
Page 307
50h-53h
32
R/W
HcRhStatus
00000000h
Page 307
54h-57h
32
R/W
HcRhPortStatus[1]
00000000h
Page 308
58h-5Bh
32
R/W
HcRhPortStatus[2]
00000000h
Page 309
5Ch-5Fh
32
R/W
HcRhPortStatus[3]
00000000h
Page 310
60h-9Fh
---
---
Reserved
xxxxxxxxh
Page 311
100h-103h
32
R/W
HceControl
00000000h
Page 311
104h-107h
32
R/W
HceInput
000000xxh
Page 312
108h-10Dh
32
R/W
HceOutput
000000xxh
Page 312
10Ch-10Fh
32
R/W
HceStatus
00000000h
Page 312
AMD Geode™ SC3200 Processor Data Book
203
Revision 5.1
Core Logic Module - Register Summary
Table 6-28. ISA Legacy I/O Register Summary
I/O Port
Type
Name
Reference
DMA Channel Control Registers (Table 6-43)
000h
R/W
DMA Channel 0 Address Register
Page 313
001h
R/W
DMA Channel 0 Transfer Count Register
Page 313
Page 313
002h
R/W
DMA Channel 1 Address Register
003h
R/W
DMA Channel 1 Transfer Count Register
Page 313
004h
R/W
DMA Channel 2 Address Register
Page 313
005h
R/W
DMA Channel 2 Transfer Count Register
Page 313
006h
R/W
DMA Channel 3 Address Register
Page 313
007h
R/W
DMA Channel 3 Transfer Count Register
Page 313
008h
Read
DMA Status Register, Channels 3:0
Page 313
Write
DMA Command Register, Channels 3:0
Page 314
Software DMA Request Register, Channels 3:0
Page 314
009h
WO
00Ah
W
DMA Channel Mask Register, Channels 3:0
Page 314
00Bh
WO
DMA Channel Mode Register, Channels 3:0
Page 315
00Ch
WO
DMA Clear Byte Pointer Command, Channels 3:0
Page 315
00Dh
WO
DMA Master Clear Command, Channels 3:0
Page 315
00Eh
WO
DMA Clear Mask Register Command, Channels 3:0
Page 315
00Fh
WO
DMA Write Mask Register Command, Channels 3:0
Page 315
0C0h
R/W
DMA Channel 4 Address Register (Not used)
Page 315
0C2h
R/W
DMA Channel 4 Transfer Count Register (Not Used)
Page 315
0C4h
R/W
DMA Channel 5 Address Register
Page 315
0C6h
R/W
DMA Channel 5 Transfer Count Register
Page 315
0C8h
R/W
DMA Channel 6 Address Register
Page 315
0CAh
R/W
DMA Channel 6 Transfer Count Register
Page 315
0CCh
R/W
DMA Channel 7 Address Register
Page 315
0CEh
R/W
DMA Channel 7 Transfer Count Register
Page 315
0D0h
Read
DMA Status Register, Channels 7:4
Page 316
Write
0D2h
WO
DMA Command Register, Channels 7:4
Page 316
Software DMA Request Register, Channels 7:4
Page 317
0D4h
W
DMA Channel Mask Register, Channels 7:4
Page 317
0D6h
WO
DMA Channel Mode Register, Channels 7:4
Page 317
Page 317
0D8h
WO
DMA Clear Byte Pointer Command, Channels 7:4
0DAh
WO
DMA Master Clear Command, Channels 7:4
Page 317
0DCh
WO
DMA Clear Mask Register Command, Channels 7:4
Page 317
0DEh
WO
DMA Write Mask Register Command, Channels 7:4
Page 318
DMA Page Registers (Table 6-44)
081h
R/W
DMA Channel 2 Low Page Register
Page 318
082h
R/W
DMA Channel 3 Low Page Register
Page 318
083h
R/W
DMA Channel 1 Low Page Register
Page 318
087h
R/W
DMA Channel 0 Low Page Register
Page 318
089h
R/W
DMA Channel 6 Low Page Register
Page 318
08Ah
R/W
DMA Channel 7 Low Page Register
Page 318
08Bh
R/W
DMA Channel 5 Low Page Register
Page 318
08Fh
R/W
Sub-ISA Refresh Low Page Register
Page 318
481h
R/W
DMA Channel 2 High Page Register
Page 318
482h
R/W
DMA Channel 3 High Page Register
Page 318
483h
R/W
DMA Channel 1 High Page Register
Page 318
204
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Register Summary
Revision 5.1
Table 6-28. ISA Legacy I/O Register Summary (Continued)
I/O Port
Type
Name
Reference
487h
R/W
DMA Channel 0 High Page Register
Page 318
489h
R/W
DMA Channel 6 High Page Register
Page 318
48Ah
R/W
DMA Channel 7 High Page Register
Page 318
48Bh
R/W
DMA Channel 5 High Page Register
Page 318
Programmable Interval Timer Registers (Table 6-45)
040h
W
PIT Timer 0 Counter
R
PIT Timer 0 Status
Page 319
041h
W
PIT Timer 1 Counter (Refresh)
Page 319
R
PIT Timer 1 Status (Refresh)
Page 319
042h
W
PIT Timer 2 Counter (Speaker)
Page 320
PIT Timer 2 Status (Speaker)
Page 320
043h
R/W
PIT Mode Control Word Register
Page 320
R
Page 319
Read Status Command
Counter Latch Command
Programmable Interrupt Controller Registers (Table 6-46)
020h / 0A0h
WO
Master / Slave PCI ICW1
Page 321
021h / 0A1h
WO
Master / Slave PIC ICW2
Page 321
021h / 0A1h
WO
Master / Slave PIC ICW3
Page 321
021h / 0A1h
WO
Master / Slave PIC ICW4
Page 321
021h / 0A1h
R/W
Master / Slave PIC OCW1
Page 321
020h / 0A0h
WO
Master / Slave PIC OCW2
Page 322
020h / 0A0h
WO
Master / Slave PIC OCW3
Page 322
020h / 0A0h
RO
Master / Slave PIC Interrupt Request and Service Registers for OCW3 Commands
Page 322
Keyboard Controller Registers (Table 6-47)
060h
R/W
External Keyboard Controller Data Register
Page 324
061h
R/W
Port B Control Register
Page 324
062h
R/W
External Keyboard Controller Mailbox Register
Page 324
064h
R/W
External Keyboard Controller Command Register
Page 324
066h
R/W
External Keyboard Controller Mailbox Register
Page 324
092h
R/W
Port A Control Register
Page 324
Real-Time Clock Registers (Table 6-48)
070h
WO
RTC Address Register
071h
R/W
RTC Data Register
Page 325
Page 325
072h
WO
RTC Extended Address Register
Page 325
073h
R/W
RTC Extended Data Register
Page 325
Miscellaneous Registers (Table 6-49)
0F0h, 0F1h
WO
Coprocessor Error Register
Page 325
170h-177h/
376h-377h
R/W
Secondary IDE Registers
Page 325
1F0-1F7h/
3F6h-3F7h
R/W
Primary IDE Registers
Page 325
4D0h
R/W
Interrupt Edge/Level Select Register 1
Page 325
4D1h
R/W
Interrupt Edge/Level Select Register 2
Page 326
AMD Geode™ SC3200 Processor Data Book
205
Revision 5.1
6.4
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Chipset Register Space
The Chipset Register Space of the Core Logic module is
comprised of six separate functions (F0-F5), each with its
own register space. Base Address Registers (BARs) in
each PCI header register space set the base address for
the configuration registers for each respective function. The
configuration registers accessed through BARs are I/O or
memory mapped. The PCI header registers in all functions
are very similar.
General Remarks:
• Reserved bits that are defined as "must be set to 0 or 1"
should be written with that value.
• Reserved bits that are not defined as "must be set to 0
or 1" should be written with a value that is read from
them.
• "Read to Clear" registers that are wider than one byte
should be read in one read operation. If they are read a
byte at a time, status bits may be lost, or not cleared.
1)
Function 0 (F0): PCI Header/Bridge Configuration
Registers for GPIO, and LPC Support (see Section
6.4.1).
2)
Function 1 (F1): PCI Header Registers for SMI Status
and ACPI Support (see Section 6.4.2 on page 252).
6.4.1
3)
Function 2 (F2): PCI Header/Channel 0 and 1 Configuration Registers for IDE Controller Support (see Section 6.4.3 on page 273).
4)
Function 3 (F3): PCI Header Registers for audio support (see Section 6.4.4 on page 279).
The register space designated as Function 0 (F0) is used
to configure Bridge features and functionality unique to the
Core Logic module. In addition, it configures the PCI portion of support hardware for the GPIO and LPC support
registers. The bit formats for the PCI Header and Bridge
Configuration registers are given in Table 6-29.
5)
Function 4 (F4): PCI Header Registers Video Processor Support (see Section 7.3 on page 345).
6)
Function 5 (F5): PCI Header Registers for X-Bus
Expansion Support (see Section 6.4.5 on page 294).
The registers at F0 Index 50h-FFh can also be
accessed at F1BAR0+I/O Offset 50h-FFh. However, the preferred method is to program these registers through the F0 register space.
Function 5 contain six BARs in their standard PCI
header locations (i.e., Index 10h, 14h, 18h, 1Ch, 20h,
and 24h). In addition there are six mask registers that
allow the six BARs to be fully programmable from 4
GB to 16 bytes for memory and from 4 GB to 4 bytes
for I/O
Located in the PCI Header registers of F0, are two Base
Address Registers (F0BARx) used for pointing to the register spaces designated for GPIO and LPC configuration
(described in Section 6.4.1.1 "GPIO Support Registers" on
page 240 and Section 6.4.1.2 "LPC Support Registers" on
page 244).
Note:
Bridge, GPIO, and LPC Registers Function 0
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support
Bit
Description
Index 00h-01h
Vendor Identification Register (RO)
Reset Value: 100Bh
Index 02h-03h
Device Identification Register (RO)
Reset Value: 0500h
Index 04h-05h
PCI Command Register (R/W)
Reset Value: 000Fh
15:10
Reserved. Must be set to 0.
9
Fast Back-to-Back Enable. This function is not supported when the Core Logic module is a master. It must always be disabled (i.e., must be set to 0).
8
SERR#. Allow SERR# assertion on detection of special errors.
0: Disable. (Default)
1: Enable.
7
Wait Cycle Control (Read Only). This function is not supported in the Core Logic module. It is always disabled (always
reads 0, hardwired).
6
Parity Error. Allow the Core Logic module to check for parity errors on PCI cycles for which it is a target and to assert
PERR# when a parity error is detected.
0: Disable. (Default)
1: Enable.
5
206
VGA Palette Snoop Enable. (Read Only) This function is not supported in the Core Logic module. It is always disabled
(always reads 0, hardwired).
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Revision 5.1
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
4
Description
Memory Write and Invalidate. Allow the Core Logic module to do memory write and invalidate cycles, if the PCI Cache
Line register (F0 Index 0Ch) is set to 32 bytes (08h).
0: Disable. (Default)
1: Enable.
3
Special Cycles. Allow the Core Logic module to respond to special cycles.
0: Disable.
1: Enable. (Default)
This bit must be enabled to allow an SMI to be generated from a CPU Shutdown cycle.
2
Bus Master. Allow the Core Logic module bus mastering capabilities.
0: Disable.
1: Enable. (Default)
This bit must be set to 1.
1
Memory Space. Allow the Core Logic module to respond to memory cycles from the PCI bus.
0: Disable.
1: Enable. (Default)
0
I/O Space. Allow the Core Logic module to respond to I/O cycles from the PCI bus:
0: Disable.
1: Enable. (Default)
This bit must be set to 1 to access I/O offsets through F0BAR0 and F0BAR1 (see F0 Index 10h and 14h).
Index 06h-07h
PCI Status Register (R/W)
Reset Value: 0280h
15
Detected Parity Error. This bit is set whenever a parity error is detected.
Write 1 to clear.
14
Signaled System Error. This bit is set whenever the Core Logic module asserts SERR# active.
Write 1 to clear.
13
Received Master Abort. This bit is set whenever a master abort cycle occurs. A master abort occurs when a PCI cycle is
not claimed, except for special cycles.
Write 1 to clear.
12
Received Target Abort. This bit is set whenever a target abort is received while the Core Logic module is the master for the
PCI cycle.
Write 1 to clear.
11
Signaled Target Abort. This bit is set whenever the Core Logic module signals a target abort. This occurs when an
address parity error occurs for an address that hits in the active address decode space of the Core Logic module.
Write 1 to clear.
10:9
DEVSEL# Timing. (Read Only) These bits are always 01, as the Core Logic module always responds to cycles for which it
is an active target with medium DEVSEL# timing.
00: Fast
01: Medium
10: Slow
11: Reserved.
8
Data Parity Detected. This bit is set when:
1)
The Core Logic module asserts PERR# or observed PERR# asserted.
2)
The Core Logic module is the master for the cycle in which the PERR# occurred, and PE is set (F0 Index 04h[6] = 1).
Write 1 to clear.
7
Fast Back-to-Back Capable. (Read Only) Enables the Core Logic module, as a target, to accept fast back-to-back transactions.
0: Disable.
1: Enable.
This bit is always set to 1.
6:0
Reserved. (Read Only) Must be set to 0 for future use.
AMD Geode™ SC3200 Processor Data Book
207
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description
Index 08h
Device Revision ID Register (RO)
Index 09h-0Bh
Index 0Ch
7:0
Reset Value: 00h
PCI Class Code Register (RO)
Reset Value: 060100h
PCI Cache Line Size Register (R/W)
Reset Value: 00h
PCI Cache Line Size Register. This register sets the size of the PCI cache line, in increments of four bytes. For memory
write and invalidate cycles, the PCI cache line size must be set to 32 bytes (08h) and the Memory Write and Invalidate bit
(F0 Index 04h[4]) must be set to 1.
Index 0Dh
PCI Latency Timer Register (R/W)
Reset Value: 00h
7:4
Reserved. Must be set to 0.
3:0
PCI Latency Timer Value. The PCI Latency Timer register prevents system lockup when a slave does not respond to a
cycle that the Core Logic module masters.
If the value is set to 00h (default), the timer is disabled.
If the timer is written with any other value, bits [3:0] become the four most significant bits in a timer that counts PCI clocks for
slave response.
The timer is reset on each valid data transfer. If the counter expires before the next assertion of TRDY# is received, the
Core Logic module stops the transaction with a master abort and asserts SERR#, if enabled to do so (via F0 Index 04h[8]).
Index 0Eh
7:0
PCI Header Type (RO)
Reset Value: 80h
PCI Header Type Register. This register defines the format of this header. This header has a format of type 0. (For more
information about this format, see the PCI Local Bus specification, revision 2.2.)
Additionally, bit 7 of this register defines whether this PCI device is a multifunction device (bit 7 = 1) or not (bit 7 = 0).
Index 0Fh
PCI BIST Register (RO)
Reset Value: 00h
This register indicates various information about the PCI Built-In Self-Test (BIST) mechanism.
Note:
7
This mechanism is not supported in the Core Logic module in the SC3200.
BIST Capable. Indicates if the device can run a Built-In Self-Test (BIST).
0: The device has no BIST functionality.
1: The device can run a BIST.
6
Start BIST. Setting this bit to 1 starts up a BIST on the device. The device resets this bit when the BIST is completed. (Not
supported.)
5:4
Reserved.
3:0
BIST Completion Code. Upon completion of the BIST, the completion code is stored in these bits. A completion code of
0000 indicates that the BIST was successfully completed. Any other value indicates a BIST failure.
Index 10h-13h
Base Address Register 0 - F0BAR0 (R/W)
Reset Value: 00000001h
This register allows access to I/O mapped GPIO runtime and configuration Registers. Bits [5:0] are read only (000001), indicating a 64byte aligned I/O address space. Refer to Table 6-30 on page 240 for the GPIO register bit formats and reset values.
31:6
GPIO Base Address.
5:0
Address Range. (Read Only)
Index 14h-17h
Base Address Register 1 - F0BAR1 (R/W)
Reset Value: 00000001h
This register allows access to I/O mapped LPC configuration registers. Bits [5:0] are read only (000001), indicating a 64-byte aligned I/O
address space. Refer to Table 6-31 on page 244 for the bit formats and reset values of the LPC registers.
31:6
LPC Base Address.
5:0
Address Range. (Read Only)
Index 18h-2Bh
Reserved
Index 2Ch-2Dh
Subsystem Vendor ID (RO)
Reset Value: 100Bh
Index 2Eh-2Fh
Subsystem ID (RO)
Reset Value: 0500h
Index 30h-3Fh
Reserved
208
Reset Value: 00h
Reset Value: 00h
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Revision 5.1
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description
Index 40h
PCI Function Control Register 1 (R/W)
7:6
Reserved. Must be set to 0.
5
Reserved. Must be set to 0.
4
PCI Subtractive Decode.
Reset Value: 39h
0: Disable transfer of subtractive decode address to external PCI bus. External PCI bus is not usable.
1: Enable transfer of subtractive decode address to external PCI bus. Recommended setting.
3
Reserved. Must be set to 1.
2
Reserved. Must be set to 0.
1
PERR# Signals SERR#. Assert SERR# when PERR# is asserted or detected as active by the Core Logic module (allows
PERR# assertion to be cascaded to NMI (SMI) generation in the system).
0: Disable.
1: Enable.
0
PCI Interrupt Acknowledge Cycle Response. The Core Logic module responds to PCI interrupt acknowledge cycles.
0: Disable.
1: Enable.
Index 41h
7:6
5
PCI Function Control Register 2 (R/W)
Reset Value: 00h
Reserved. Must be set to 0.
X-Bus Configuration Trap. If this bit is set to 1 and an access occurs to one of the configuration registers in PCI Function
5 (F5) register space, an SMI is generated. Writes are trapped; access to the register is denied. Reads are snooped; access
to the register is allowed.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[9].
Second level SMI status is reported at F1BAR0+I/O Offset 04h/06h[5].
4
Video Configuration Trap. If this bit is set to 1 and an access occurs to one of the configuration registers in PCI Function 4
(F4) register space, an SMI is generated. Writes are trapped; access to the register is denied. Reads are snooped; access
to the register is allowed.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[9].
Second level SMI status is reported at F1BAR0+I/O Offset 04h/06h[5].
3
Audio Configuration Trap. If this bit is set to 1 and an access occurs to one of the configuration registers in PCI Function
3 (F3) register space, an SMI is generated. Writes are trapped; access to the register is denied. Reads are snooped; access
to the register is allowed.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[9].
Second level SMI status is reported at F1BAR0+I/O Offset 04h/06h[5].
2
IDE Configuration Trap. If this bit is set to 1 and an access occurs to one of the configuration registers in PCI Function 2
(F2) register space, an SMI is generated. Writes are trapped; access to the register is denied. Reads are snooped; access
to the register is allowed.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[9].
Second level SMI status is reported at F1BAR0+I/O Offset 04h/06h[5].
AMD Geode™ SC3200 Processor Data Book
209
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
1
Description
Power Management Configuration Trap. If this bit is set to 1 and an access occurs to one of the configuration registers in
PCI Function 1 (F1) register space, an SMI is generated. Writes are trapped; access to the register is denied. Reads are
snooped; access to the register is allowed.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[9].
Second level SMI status is reported at F1BAR0+I/O Offset 04h/06h[5].
0
Legacy Configuration Trap. If this bit is set to 1 and an access occurs to one of the configuration registers in PCI Function
0 (F0), an SMI is generated. Reads and writes are snooped; access to the register is allowed.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[9].
Second level SMI status is reported at F1BAR0+I/O Offset 04h/06h[5].
Index 42h
Reserved
Reset Value: 00h
Index 43h
Delayed Transactions Register (R/W)
Reset Value: 02h
7:6
Reserved. Must be set to 0.
5
Reserved. Must be set to 1.
4
Enable PCI Delayed Transactions for Access to I/O Address 170h-177h (Secondary IDE Channel). PIO mode uses
repeated I/O transactions that are faster when non-delayed transactions are used.
0: I/O addresses complete as fast as possible on PCI. (Default)
1: Accesses to Secondary IDE channel I/O addresses are delayed transactions on PCI.
For best performance of VIP, this bit should be set to 1 unless PIO mode 3 or 4 are used.
3
Enable PCI Delayed Transactions for Access to I/O Address 1F0h-1F7h (Primary IDE Channel). PIO mode uses
repeated I/O transactions that are faster when non-delayed transactions are used.
0: I/O addresses complete as fast as possible on PCI. (Default)
1: Accesses to Primary IDE channel I/O addresses are delayed transactions on PCI.
For best performance of VIP, this bit should be set to 1 unless PIO mode 3 or 4 are used.
2
Enable PCI Delayed Transactions for AT Legacy PIC I/O Addresses. Some PIC status reads are long. Enabling delayed
transactions help reduce DMA latency for high bandwidth devices like VIP.
0: PIC I/O addresses complete as fast as possible on PCI. (Default)
1: Accesses to PIC I/O addresses are delayed transactions on PCI.
For best performance of VIP, this bit should be set to 1.
1
Enable PCI Delayed Transactions for AT Legacy PIT I/O Addresses. Some x86 programs (certain benchmarks/diagnostics) assume a particular latency for PIT accesses; this bit allows that code to work.
0: PIT I/O addresses complete as fast as possible on PCI.
1: Accesses to PIT I/O addresses are delayed transactions on PCI. (Default)
For best performance (e.g., when running Microsoft Windows®), this bit should be set to 0.
0
Reserved. Must be set to 0.
Index 44h
7
Reset Control Register (R/W)
Reset Value: 01h
AC97 Soft Reset. Active low reset for the AC97 codec interface.
0: AC97_RST# is driven high. (Default)
1: AC97_RST# is driven low.
6:4
3
Reserved. Must be set to 0.
IDE Controller Reset. Reset the IDE controller.
0: Disable.
1: Enable.
Write 0 to clear. This bit is level-sensitive and must be cleared after the reset is enabled.
210
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Revision 5.1
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
2
Description
IDE Reset. Reset IDE bus.
0: Disable.
1: Enable (drive IDE_RST# low).
Write 0 to clear. This bit is level-sensitive and must be cleared after the reset is enabled.
Note:
1
When X-Bus Warm Start is enabled (bit 0 = 1) or during POR#, IDE_RST# is put into TRI-STATE mode. To properly reset the IDE bus, after POR# the boot code must cause IDE_RST# to activate.
PCI Reset. Reset PCI bus.
0: Disable.
1: Enable.
When this bit is set to 1, the Core Logic module output signal PCIRST# is asserted and all devices on the PCI bus (including
PCIUSB) are reset. No other function within the Core Logic module is affected by this bit.
Write 0 to clear this bit. This bit is level-sensitive and must be cleared after the reset is enabled.
0
X-Bus Warm Start. Writing and reading this bit each have different meanings.
When reading this bit, it indicates whether or not a warm start occurred since power-up:
0: A warm start occurred.
1: No warm start has occurred.
When writing this bit, it can be used to trigger a system-wide reset:
0: No effect.
1: Execute system-wide reset (used only for clock configuration at power-up).
Index 45h
Reserved
Reset Value: 00h
Index 46h
PCI Functions Enable Register (R/W)
Reset Value: FEh
7:6
5
Reserved. Resets to 11.
F5 (PCI Function 5). When asserted (set to 1), enables the register space designated as F5.
This bit must always be set to 1. (Default)
4
F4 (PCI Function 4). When asserted (set to 1), enables the register space designated as F4.
This bit must always be set to 1. (Default)
3
F3 (PCI Function 3). When asserted (set to 1), enables the register space designated as F3.
This bit must always be set to 1. (Default)
2
F2 (PCI Function 2). When asserted (set to 1), enables the register space designated as F2.
This bit must always be set to 1. (Default)
1
F1 (PCI Function 1). When asserted (set to 1), enables the register space designated as F1.
This bit must always be set to 1. (Default)
0
Reserved. Must be set to 0.
Index 47h
7:3
2
Miscellaneous Enable Register (R/W)
Reset Value: 00h
Reserved. Must be set to 0.
F0BAR1 (PCI Function 0, Base Address Register 1). F0BAR1, pointer to I/O mapped LPC configuration registers.
0: Disable.
1: Enable.
1
F0BAR0 (PCI Function 0, Base Address Register 0). F0BAR0, pointer to I/O mapped GPIO configuration registers.
0: Disable.
1: Enable.
0
Reserved. Must be set to 0.
Index 48h-4Bh
AMD Geode™ SC3200 Processor Data Book
Reserved
Reset Value: 00h
211
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description
Index 4Ch-4Fh
31:0
Top of System Memory (R/W)
Reset Value: FFFFFFFFh
Top of System Memory. Highest address in system used to determine active decode for external PCI mastered memory
cycles.
If an external PCI master requests a memory address below the value programmed in this register, the cycle is transferred
from the external PCI bus interface to the Fast-PCI interface for servicing by the GX1 module.
Note:
The four least significant bits must be set to 1100.
Index 50h
7
PIT Control/ISA CLK Divider (R/W)
Reset Value: 7Bh
PIT Software Reset.
0: Disable.
1: Enable.
6
PIT Counter 1.
0: Forces Counter 1 output (OUT1) to zero.
1: Allows Counter 1 output (OUT1) to pass to the Port 061h[4].
5
PIT Counter 1 Enable.
0: Sets GATE1 input low.
1: Sets GATE1 input high.
4
PIT Counter 0.
0: Forces Counter 0 output (OUT0) to zero.
1: Allows Counter 0 output (OUT0) to pass to IRQ0.
3
PIT Counter 0 Enable.
0: Sets GATE0 input low.
1: Sets GATE0 input high.
2:0
ISA Clock Divisor. Determines the divisor of the PCI clock used to make the ISA clock, which is typically programmed for
approximately 8 MHz:
000: Divide by 1
001: Divide by 2
010: Divide by 3
011: Divide by 4
100: Divide by 5
101: Divide by 6
110: Divide by 7
111: Divide by 8
If PCI clock = 25 MHz, use setting of 010 (divide by 3).
If PCI clock = 30 or 33 MHz, use a setting of 011 (divide by 4).
Index 51h
7:4
ISA I/O Recovery Control Register (R/W)
Reset Value: 40h
8-Bit I/O Recovery. These bits determine the number of ISA bus clocks between back-to-back 8-bit I/O read cycles. This
count is in addition to a preset one-clock delay built into the controller.
0000: 1 PCI clock
0001: 2 PCI clocks
:::
:::
:::
1111: 16 PCI clocks
3:0
16-Bit I/O Recovery. These bits determine the number of ISA bus clocks between back-to-back 16-bit I/O cycles. This
count is in addition to a preset one-clock delay built into the controller.
0000: 1 PCI clock
0001: 2 PCI clocks
:::
:::
:::
1111: 16 PCI clocks
212
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Revision 5.1
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description
Index 52h
7
ROM/AT Logic Control Register (R/W)
Reset Value: 98h
Snoop Fast Keyboard Gate A20 and Fast Reset. Enables the snoop logic associated with keyboard commands for A20
Mask and Reset.
0: Disable snooping. The keyboard controller handles the commands.
1: Enable snooping.
6:5
4
Reserved. Must be set to 0.
Enable A20M# De-assertion on Warm Reset. Force A20M# high during a Warm Reset (guarantees that A20M# is deasserted regardless of the state of A20).
0: Disable.
1: Enable.
3
Enable Port 092h (Port A). Port 092h decode and the logical functions.
0: Disable.
1: Enable.
2
Upper ROM Size. Selects upper ROM addressing size.
0: 256K (FFFC0000h-FFFFFFFFh).
1: Use ROM Mask register (F0 Index 6Ch).
ROMCS# goes active for the above ranges whether strapped for ISA or LPC. (Refer to F0BAR1+I/O Offset 10h[15] for further strapping/programming details.)
The selected range can then be either positively or subtractively decoded through F0 Index 5Bh[5].
1
ROM Write Enable. When asserted, enables writes to ROM space, allowing Flash programming.
If strapped for ISA and this bit is set to 1, writes to the configured ROM space asserts ROMCS#, enabling the write cycle to
the Flash device on the ISA bus. Otherwise, ROMCS# is inhibited for writes.
If strapped for LPC and this bit is set to 1, the cycle runs on the LPC bus. Otherwise, the LPC bus cycle is inhibited for
writes.
Refer to F0BAR1+I/O Offset 10h[15] for further strapping/programming details.
0
Lower ROM Size. Selects lower ROM addressing size in which ROMCS# goes active.
0: Lower ROM access are 000F0000h-000FFFFFh (64 KB). (Default)
1: Lower ROM accesses are 000E0000h-000FFFFFh (128 KB).
ROMCS# goes active for the above ranges whether strapped for ISA or LPC. (Refer to F0BAR1+I/O Offset 10h[15] for further strapping/programming details.)
The selected range can then be either positively or subtractively decoded through F0 Index 5Bh[5].
Index 53h
Alternate CPU Support Register (R/W)
7:6
Reserved. Must be set to 0.
5
Bidirectional SMI Enable.
Reset Value: 00h
0: Disable.
1: Enable.
This bit must be set to 0.
4:3
Reserved. Must be set to 0.
2
Reserved. Must be set to 0.
1
IRQ13 Function Selection. Selects function of the internal IRQ13/FERR# signal.
0: FERR#.
1: IRQ13.
This bit must be set to 1.
0
Generate SMI on A20M# Toggle.
0: Disable.
1: Enable.
This bit must be set to 1.
SMI status is reported at F1BAR0+I/O Offset 00h/02h[7].
AMD Geode™ SC3200 Processor Data Book
213
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description
Index 54h-59h
Index 5Ah
Reserved
Reset Value: 00h
Decode Control Register 1 (R/W)
Reset Value: 01h
Indicates PCI positive or negative decoding for various I/O ports on the ISA bus.
Note:
Positive decoding by the Core Logic module speeds up I/O cycle time. The I/O ports mentioned in the bit descriptions below, do
not exist in the Core Logic module. It is assumed that if positive decode is enabled for a port, the port exists on the ISA bus.
7
Secondary Floppy Positive Decode. Selects PCI positive or subtractive decoding for accesses to I/O ports 372h-375h
and 377h.
0: Subtractive.
1: Positive.
6
Primary Floppy Positive Decode. Selects PCI positive or subtractive decoding for accesses to I/O ports 3F2h-3F5h and
3F7h.
0: Subtractive.
1: Positive.
5
COM4 Positive Decode. Selects PCI positive or subtractive decoding for accesses to I/O ports 2E8h-2EFh.
0: Subtractive.
1: Positive.
4
COM3 Positive Decode. Selects PCI positive or subtractive decoding for accesses to I/O ports 3E8h-3EFh.
0: Subtractive.
1: Positive.
3
COM2 Positive Decode. Selects PCI positive or subtractive decoding for accesses to I/O ports 2F8h-2FFh.
0: Subtractive.
1: Positive.
2
COM1 Positive Decode. Selects PCI positive or subtractive decoding for accesses to I/O ports 3F8h-3FFh.
0: Subtractive.
1: Positive.
1
Keyboard Controller Positive Decode. Selects PCI positive or subtractive decoding for accesses to I/O Ports 060h and
064h (as well as 062h and 066h, if enabled - F4 Index 5Bh[7] = 1).
0: Subtractive.
1: Positive.
Note:
0
If F0BAR1+I/O Offset 10h bits 10 = 0 and 16 = 1, then this bit must be written 0.
Real-Time Clock Positive Decode. Selects PCI positive or subtractive decoding for accesses to I/O Ports 070h-073h.
0: Subtractive.
1: Positive.
Index 5Bh
Note:
7
Decode Control Register 2 (R/W)
Reset Value: 20h
Positive decoding by the Core Logic module speeds up the I/O cycle time. The Keyboard, LPT3, LPT2, and LPT1 I/O ports do
not exist in the Core Logic module. It is assumed that if positive decoding is enabled for any of these ports, the port exists on
the ISA bus.
Keyboard I/O Port 062h/066h Positive Decode. This alternate port to the keyboard controller is provided in support of
power management features.
0: Disable.
1: Enable.
6
Reserved. Must be set to 0.
5
BIOS ROM Positive Decode. Selects PCI positive or subtractive decoding for accesses to the configured ROM space.
0: Subtractive.
1: Positive.
ROM configuration is at F0 Index 52h[2:0].
214
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description
4
Secondary IDE Controller Positive Decode. Selects PCI positive or subtractive decoding for accesses to I/O ports 170h177h and 376h-377h (excluding writes to 377h).
0: Subtractive. Subtractively decoded IDE addresses are forwarded to the PCI slot bus. If a master abort occurs, they are
then forwarded to ISA.
1: Positive. Positively decoded IDE addresses are forwarded to the internal IDE controller and then to the IDE bus.
3
Primary IDE Controller Positive Decode. Selects PCI positive or subtractive decoding for accesses to I/O ports 1F0h1F7h and 3F6h-3F7h (excluding writes to 3F7h).
0: Subtractive. Subtractively decoded IDE addresses are forwarded to the PCI slot bus. If a master abort occurs, they are
then forwarded to ISA.
1: Positive. Positively decoded IDE addresses are forwarded to the internal IDE controller and then to the IDE bus.
2
LPT3 Positive Decode. Selects PCI positive or subtractive decoding for accesses to I/O ports 278h-27Fh.
0: Subtractive.
1: Positive.
1
LPT2 Positive Decode. Selects PCI positive or subtractive decoding for accesses to I/O ports 378h-37Fh.
0: Subtractive.
1: Positive.
0
LPT1 Positive Decode. Selects PCI positive or subtractive decoding for accesses to I/O ports 3BCh-3BFh
0: Subtractive.
1: Positive.
Index 5Ch
PCI Interrupt Steering Register 1 (R/W)
Reset Value: 00h
Indicates target interrupts for signals INTB# and INTA#.
Note:
The target interrupt must first be configured as level sensitive via I/O Ports 4D0h and 4D1h in order to maintain PCI interrupt
compatibility.
7:4
INTB# (EBGA Ball AF1 / TEPBGA Ball C26) Target Interrupt.
0000: Disable
0001: IRQ1
0010: Reserved
0011: IRQ3
3:0
0100: IRQ4
0101: IRQ5
0110: IRQ6
0111: IRQ7
1000: Reserved
1001: IRQ9
1010: IRQ10
1011: IRQ11
1100: IRQ12
1101: Reserved
1110: IRQ14
1111: IRQ15
INTA# (EBGA Ball AE3 / TEPBGA Ball D26) Target Interrupt.
0000: Disable
0001: IRQ1
0010: Reserved
0011: IRQ3
Index 5Dh
0100: IRQ4
0101: IRQ5
0110: IRQ6
0111: IRQ7
1000: Reserved
1001: IRQ9
1010: IRQ10
1011: IRQ11
PCI Interrupt Steering Register 2 (R/W)
1100: IRQ12
1101: Reserved
1110: IRQ14
1111: IRQ15
Reset Value: 00h
Indicates target interrupts for signals INTD# and INTC#. Note that INTD# is muxed with IDE_DATA7 (selection made via PMR[24]) and
INTC# is muxed with GPIO19+IOCHRDY (selection made via PMR[9,4]). See Table 4-2 on page 88 for PMR bit descriptions.
Note:
7:4
The target interrupt must first be configured as level sensitive via I/O Ports 4D0h and 4D1h in order to maintain PCI interrupt
compatibility.
INTD# (EBGA Ball B22 / TEPBGA Ball AA2) Target Interrupt.
0000: Disable
0001: IRQ1
0010: Reserved
0011: IRQ3
3:0
0100: IRQ4
0101: IRQ5
0110: IRQ6
0111: IRQ7
1000: Reserved
1001: IRQ9
1010: IRQ10
1011: IRQ11
1100: IRQ12
1101: Reserved
1110: IRQ14
1111: IRQ15
1000: Reserved
1001: IRQ9
1010: IRQ10
1011: IRQ11
1100: IRQ12
1101: Reserved
1110: IRQ14
1111: IRQ15
INTC# (EBGA Ball H4 / TEPBGA Ball C9) Target Interrupt.
0000: Disable
0001: IRQ1
0010: Reserved
0011: IRQ3
0100: IRQ4
0101: IRQ5
0110: IRQ6
0111: IRQ7
Index 5Eh-5Fh
AMD Geode™ SC3200 Processor Data Book
Reserved
Reset Value: 00h
215
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description
Index 60h-63h
31:8
7
ACPI Control Register (R/W)
Reset Value: 00000000h
Reserved. Must be set to 0.
SUSP_3V Shut Down PLL5. Allow internal SUSP_3V to shut down PLL5.
0: Clock generator is stopped when internal SUSP_3V is active.
1:
6
Clock generator continues working when internal SUSP_3V is active.
SUSP_3V Shut Down PLL4. Allow internal SUSP_3V to shut down PLL4
0: Clock generator is stopped when internal SUSP_3V is active.
1:
5
Clock generator continues working when internal SUSP_3V is active.
SUSP_3V Shut Down PLL3. Allow internal SUSP_3V to shut down PLL3.
0: Clock generator is stopped when internal SUSP_3V is active.
1:
4
Clock generator continues working when internal SUSP_3V is active.
SUSP_3V Shut Down PLL2. Allow internal SUSP_3V to shut down PLL2.
0: Clock generator is stopped when internal SUSP_3V is active.
1:
3
Clock generator continues working when internal SUSP_3V is active.
SUSP_3V Shut Down PLL6. Allow internal SUSP_3V to shut down PLL6.
0: Clock generator is stopped when internal SUSP_3V is active.
1:
2
Clock generator continues working when internal SUSP_3V is active.
ACPI C3 SUSP_3V Enable. Allow internal SUSP_3V to be active during C3 state.
0: Disable.
1: Enable.
1
ACPI SL1 SUSP_3V Enable. Allow internal SUSP_3V to be active during SL1 sleep state.
0: Disable.
1: Enable.
0
ACPI C3 Support Enable. Allow support of C3 states.
0: Disable.
1: Enable.
Index 64h-6Bh
Reserved
Index 6Ch-6Fh
ROM Mask Register (R/W)
Note:
Reset Value: 00h
Reset Value: 0000FFF0h
Register must be read/written as a DWORD.
31:16
Reserved. Must be written to 0.
15:8
Reserved. Must be written to FFh.
7:4
ROM Size. If F0 Index 52h[2] = 1:
0000: 16 MB = FF000000h-FFFFFFFFh
1000: 8 MB = FF800000h-FFFFFFFFh
1100: 4 MB = FFC00000h-FFFFFFFFh
1110: 2 MB = FFE00000h-FFFFFFFFh
1111: 1 MB = FFF00000h-FFFFFFFFh
All other settings for these bits are reserved.
3:0
216
Reserved. Must be set to 0.
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Revision 5.1
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description
Index 70h-71h
15:0
IOCS1# Base Address Register (R/W)
Reset Value: 0000h
I/O Chip Select 1 Base Address. This 16-bit value represents the I/O base address used to enable assertion of IOCS1#
(EBGA ball H2 or AL12 / TEPBGA ball D10 or N30 - see PMR[23] in Table 4-2 on page 88).
This register is used in conjunction with F0 Index 72h (IOCS1# Control register).
Index 72h
IOCS1# Control Register (R/W)
Reset Value: 00h
This register is used in conjunction with F0 Index 70h (IOCS1# Base Address register).
7
I/O Chip Select 1 Positive Decode (IOCS1#).
0: Disable.
1: Enable.
6
Writes Result in Chip Select. When this bit is set to 1, writes to configured I/O address (base address configured in F0
Index 70h; range configured in bits [4:0]) cause IOCS1# to be asserted.
0: Disable.
1: Enable.
5
Reads Result in Chip Select. When this bit is set to 1, reads from configured I/O address (base address configured in F0
Index 70h; range configured in bits [4:0]) cause IOCS1# to be asserted.
0: Disable.
1: Enable.
4:0
IOCS1# I/O Address Range. This 5-bit field is used to select the range of IOCS1#.
00000: 1 Byte
00001: 2 Bytes
00011: 4 Bytes
00111: 8 Bytes
01111: 16 Bytes
11111: 32 Bytes
All other combinations are reserved.
Index 73h
Reserved
Index 74h-75h
15:0
IOCS0# Base Address Register (R/W)
Reset Value: 00h
Reset Value: 0000h
I/O Chip Select 0 Base Address. This 16-bit value represents the I/O base address used to enable the assertion of
IOCS0# (EBGA ball J4 / TEPBGA ball A10 - see PMR[23] in Table 4-2 on page 88).
This register is used in conjunction with F0 Index 76h (IOCS0# Control register).
Index 76h
IOCS0# Control Register (R/W)
Reset Value: 00h
This register is used in conjunction with F0 Index 74h (IOCS0# Base Address register).
7
I/O Chip Select 0 Positive Decode (IOCS0#).
0: Disable.
1: Enable.
6
Writes Result in Chip Select. When this bit is set to 1, writes to configured I/O address (base address configured in F0
Index 74h; range configured in bits [4:0]) cause IOCS0# to be asserted.
0: Disable.
1: Enable.
5
Reads Result in Chip Select. When this bit is set to 1, reads from configured I/O address (base address configured in F0
Index 74h; range configured in bits [4:0]) cause IOCS0# to be asserted.
0: Disable.
1: Enable.
4:0
IOCS0# I/O Address Range. This 5-bit field is used to select the range of IOCS0#.
00000: 1 Byte
00001: 2 Bytes
00011: 4 Bytes
00111: 8 Bytes
Index 77h
AMD Geode™ SC3200 Processor Data Book
01111: 16 Bytes
11111: 32 Bytes
All other combinations are reserved.
Reserved
Reset Value: 00h
217
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description
Index 78h-7Bh
31:0
DOCCS# Base Address Register (R/W)
Reset Value: 00000000h
DiskOnChip Chip Select Base Address. This 32-bit value represents the memory base address used to enable assertion
of DOCCS# (EBGA ball H3 or AJ13 / TEPBGA ball A9 or N31, see PMR[23] in Table 4-2 on page 88).
This register is used in conjunction with F0 Index 7Ch (DOCCS# Control register).
Index 7Ch-7Fh
DOCCS# Control Register (R/W)
Reset Value: 00000000h
This register is used in conjunction with F0 Index 78h (DOCCS# Base Address register).
31:27
26
Reserved. Must be set to 0.
DiskOnChip Chip Select Positive Decode (DOCCS#).
0: Disable.
1: Enable.
25
Writes Result in Chip Select. When this bit is set to 1, writes to configured memory address (base address configured in
F0 Index 78h; range configured in bits [18:0]) cause DOCCS# to be asserted.
0: Disable.
1: Enable.
24
Reads Result in Chip Select. When this bit is set to 1, reads from configured memory address (base address configured in
F0 Index 78h; range configured in bits [18:0]) cause DOCCS# to be asserted.
0: Disable.
1: Enable.
23:19
Reserved. Must be set to 0.
18:0
DOCCS# Memory Address Range. This 19-bit mask is used to qualify accesses on which DOCCS# is asserted by masking the upper 19 bits of the incoming PCI address (AD[31:13]).
Index 80h
7:6
5
Power Management Enable Register 1 (R/W)
Reset Value: 00h
Reserved. Must be set to 0.
Codec SDATA_IN SMI. When set to 1, this bit allows an SMI to be generated in response to an AC97 codec producing a
positive edge on SDATA_IN.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 87h/F7h[2].
4
Video Speedup. Any video activity, as decoded from the serial connection (PSERIAL) from the GX1 module disables clock
throttling (via internal SUSP#/SUSPA# handshake) for a configurable duration when system is power-managed using CPU
Suspend modulation.
0: Disable.
1: Enable.
The duration of the speedup is configured in the Video Speedup Timer Count Register (F0 Index 8Dh). Detection of an
external VGA access (3Bx, 3Cx, 3Dx and A000h-B7FFh) on the PCI bus is also supported. This configuration is non-standard, but it does allow the power management routines to support an external VGA chip.
3
IRQ Speedup. Any unmasked IRQ (per I/O Ports 021h/0A1h) or SMI disables clock throttling (via internal SUSP#/SUSPA#
handshake) for a configurable duration when system is power-managed using CPU Suspend modulation.
0: Disable.
1: Enable.
The duration of the speedup is configured in the IRQ Speedup Timer Count Register (F0 Index 8Ch).
2
Traps. Globally enable all power management I/O traps.
0: Disable.
1: Enable.
This excludes the audio I/O traps, which are enabled via F3BAR0+Memory Offset 18h.
218
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Revision 5.1
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
1
Description
Idle Timers. Device idle timers.
0: Disable.
1: Enable.
Note:
0
Disable at this level does not reload the timers on the enable. The timers are disabled at their current counts.
This bit has no affect on the Suspend Modulation register (F0 Index 94h).
Only applicable when in APM mode (F1BAR1+I/O Offset 0Ch[0] = 0) and not ACPI mode.
Power Management. Global power management.
0: Disable.
1: Enable.
This bit must be set to 1 immediately after POST for power management resources to function.
Index 81h
7
Power Management Enable Register 2 (R/W)
Reset Value: 00h
Video Access Idle Timer Enable. Turn on Video Idle Timer Count Register (F0 Index A6h) and generate an SMI when the
timer expires.
0: Disable.
1: Enable.
If an access occurs in the video address range (sets bit 0 of the GX1 module’s PSERIAL register) the timer is reloaded with
the programmed count.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 85h/F5h[7].
6
User Defined Device 3 (UDEF3) Idle Timer Enable. Turn on UDEF3 Idle Timer Count Register (F0 Index A4h) and generate an SMI when the timer expires.
0: Disable.
1: Enable.
If an access occurs in the programmed address range, the timer is reloaded with the programmed count.
UDEF3 address programming is at F0 Index C8h (base address register) and CEh (control register).
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 85h/F5h[6].
5
User Defined Device 2 (UDEF2) Idle Timer Enable. Turn on UDEF2 Idle Timer Count Register (F0 Index A2h) and generate an SMI when the timer expires.
0: Disable.
1: Enable.
If an access occurs in the programmed address range, the timer is reloaded with the programmed count.
UDEF2 address programming is at F0 Index C4h (base address register) and CDh (control register).
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 85h/F5h[5].
4
User Defined Device 1 (UDEF1) Idle Timer Enable. Turn on UDEF1 Idle Timer Count Register (F0 Index A0h) and generate an SMI when the timer expires.
0: Disable.
1: Enable.
If an access occurs in the programmed address range, the timer is reloaded with the programmed count.
UDEF1 address programming is at F0 Index C0h (base address register) and CCh (control register).
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 85h/F5h[4].
AMD Geode™ SC3200 Processor Data Book
219
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
3
Description
Keyboard/Mouse Idle Timer Enable. Turn on Keyboard/Mouse Idle Timer Count Register (F0 Index 9Eh) and generate an
SMI when the timer expires.
0: Disable.
1: Enable.
If an access occurs in the address ranges listed below, the timer is reloaded with the programmed count:
— Keyboard Controller: I/O Ports 060h/064h.
— COM1: I/O Port 3F8h-3FFh (if F0 Index 93h[1:0] = 10 this range is included).
— COM2: I/O Port 2F8h-2FFh (if F0 Index 93h[1:0] = 11 this range is included).
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 85h/F5h[3].
2
Parallel/Serial Idle Timer Enable. Turn on Parallel/Serial Port Idle Timer Count Register (F0 Index 9Ch) and generate an
SMI when the timer expires.
0: Disable.
1: Enable.
If an access occurs in the address ranges listed below, the timer is reloaded with the programmed count.
— LPT1: I/O Port 3BCh-3BEh.
— LPT2: I/O Port 378h-37Fh.
— COM1: I/O Port 3F8h-3FFh (if F0 Index 93h[1:0] = 10 this range is excluded).
— COM2: I/O Port 2F8h-2FFh (if F0 Index 93h[1:0] = 11 this range is excluded).
— COM3: I/O Port 3E8h-3EFh.
— COM4: I/O Port 2E8h-2EFh.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 85h/F5h[2].
1
Floppy Disk Idle Timer Enable. Turn on Floppy Disk Idle Timer Count Register (F0 Index 9Ah) and generate an SMI when
the timer expires.
0: Disable.
1: Enable.
If an access occurs in the address ranges (listed below, the timer is reloaded with the programmed count.
— Primary floppy disk: I/O Port 3F2h-3F5h, 3F7h.
— Secondary floppy disk: I/O Port 372h-375h, 377h.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 85h/F5h[1].
0
Primary Hard Disk Idle Timer Enable. Turn on Primary Hard Disk Idle Timer Count Register (F0 Index 98h) and generate
an SMI when the timer expires.
0: Disable.
1: Enable.
If an access occurs in the address ranges selected in F0 Index 93h[5], the timer is reloaded with the programmed count.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 85h/F5h[0].
220
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Revision 5.1
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description
Index 82h
7
Power Management Enable Register 3 (R/W)
Reset Value: 00h
Video Access Trap. If this bit is enabled and an access occurs in the video address range (sets bit 0 of the GX1 module’s
PSERIAL register), an SMI is generated.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 86h/F6h[7].
6
User Defined Device 3 (UDEF3) Access Trap. If this bit is enabled and an access occurs in the programmed address
range, an SMI is generated. UDEF3 address programming is at F0 Index C8h (Base Address register) and CEh (Control
register).
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[9].
Second level SMI status is reported at F1BAR0+I/O Offset 04h/06h[4].
5
User Defined Device 2 (UDEF2) Access Trap. If this bit is enabled and an access occurs in the programmed address
range, an SMI is generated. UDEF2 address programming is at F0 Index C4h (Base Address register) and CDh (Control
register).
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[9].
Second level SMI status is reported at F1BAR0+I/O Offset 04h/06h[3].
4
User Defined Device 1 (UDEF1) Access Trap. If this bit is enabled and an access occurs in the programmed address
range, an SMI is generated. UDEF1 address programming is at F0 Index C0h (base address register), and CCh (control
register).
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[9].
Second level SMI status is reported at F1BAR0+I/O Offset 04h/06h[2].
3
Keyboard/Mouse Access Trap.
0: Disable.
1: Enable.
If this bit is enabled and an access occurs in the address ranges listed below, an SMI is generated.
— Keyboard Controller: I/O Ports 060h/064h.
— COM1: I/O Port 3F8h-3FFh (if F0 Index 93h[1:0] = 10 this range is included).
— COM2: I/O Port 2F8h-2FFh (if F0 Index 93h[1:0] = 11 this range is included).
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 86h/F6h[3].
2
Parallel/Serial Access Trap.
0: Disable.
1: Enable.
If this bit is enabled and an access occurs in the address ranges listed below, an SMI is generated.
— LPT1: I/O Port 3BCh-3BEh.
— LPT2: I/O Port 378h-37Fh.
— COM1: I/O Port 3F8h-3FFh (if F0 Index 93h[1:0] = 10 this range is excluded).
— COM2: I/O Port 2F8h-2FFh (if F0 Index 93h[1:0] = 11 this range is excluded).
— COM3: I/O Port 3E8h-3EFh.
— COM4: I/O Port 2E8h-2EFh.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 86h/F6h[2].
AMD Geode™ SC3200 Processor Data Book
221
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
1
Description
Floppy Disk Access Trap.
0: Disable.
1: Enable.
If this bit is enabled and an access occurs in the address ranges listed below, an SMI is generated.
— Primary floppy disk: I/O Port 3F2h-3F5h, 3F7h.
— Secondary floppy disk: I/O Port 372h-375h, 377h.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 86h/F6h[1].
0
Primary Hard Disk Access Trap.
0: Disable.
1: Enable.
If this bit is enabled and an access occurs in the address ranges selected in F0 Index 93h[5], an SMI is generated.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 86h/F6h[0].
Index 83h
7
Power Management Enable Register 4 (R/W)
Reset Value: 00h
Secondary Hard Disk Idle Timer Enable. Turn on Secondary Hard Disk Idle Timer Count Register (F0 Index ACh) and
generate an SMI when the timer expires.
0: Disable.
1: Enable.
If an access occurs in the address ranges selected in F0 Index 93h[4], the timer is reloaded with the programmed count.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 86h/F6h[4].
6
Secondary Hard Disk Access Trap. If this bit is enabled and an access occurs in the address ranges selected in F0 Index
93h[4], an SMI is generated.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 86h/F6h[5].
5
ACPI Timer SMI. Allow SMI generation for MSB toggles on the ACPI Timer (F1BAR0+I/O Offset 1Ch or
F1BAR1+I/O Offset 1Ch).
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 87h/F7h[0].
4
THRM# SMI. Allow SMI generation on assertion of THRM#.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 87h/F7h[6].
3
VGA Timer Enable. Turn on VGA Timer Count Register (F0 Index 8Eh) and generate an SMI when the timer reaches 0.
0: Disable.
1: Enable.
If an access occurs in the programmed address range, the timer is reloaded with the programmed count. F0 Index 8Bh[6]
selects the timebase for the VGA Timer.
SMI status is reported at F1BAR0+I/O Offset 00h/02h[6] (top level only).
222
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Revision 5.1
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
2
Description
Video Retrace Interrupt SMI. Allow SMI generation whenever video retrace occurs.
0: Disable.
1: Enable.
This information is decoded from the serial connection (PSERIAL register, bit 7) from the GX1 module. This function is normally not used for power management but for soft (VSA) VGA routines.
SMI status reporting is at F1BAR0+I/O Offset 00h/02h[5] (top level only).
1
General Purpose Timer 2 Enable. Turn on GP Timer 2 Count Register (F0 Index 8Ah) and generate an SMI when the
timer expires.
0: Disable.
1: Enable.
This idle timer is reloaded from the assertion of GPIO7 (if programmed to do so). GP Timer 2 programming is at F0 Index
8Bh[5,3,2].
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[9].
Second level SMI status is reported at F1BAR0+I/O Offset 04h/06h[1].
0
General Purpose Timer 1 Enable. Turn on GP Timer 1 Count Register (F0 Index 88h) and generate an SMI when the
timer expires.
0: Disable.
1: Enable.
This idle timer’s load is multi-sourced and gets reloaded any time an enabled event (F0 Index 89h[6:0]) occurs.
GP Timer 1 programming is at F0 Index 8Bh[4].
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[9].
Second level SMI status is reported at F1BAR0+I/O Offset 04h/06h[0].
Index 84h
Second Level PME/SMI Status Mirror Register 1 (RO)
Reset Value: 00h
The bits in this register are used for the second level of status reporting. The top level is reported at F1BAR0+I/O Offset 00h/02h[0].
This register is called a "mirror" register since an identical register exists at F0 Index F4h. Reading this register does not clear the status,
while reading its counterpart at F0 Index F4h clears the status at both the second and the top levels.
7:3
2
Reserved. Reads as 0.
GPWIO2 SMI Status. Indicates whether or not an SMI was caused by a transition on the GPWIO2 pin.
0: No.
1: Yes.
To enable SMI generation:
1) Ensure that GPWIO2 is enabled as an input: F1BAR1+I/O Offset 15h[2] = 0.
2) Set F1BAR1+I/O Offset 15h[6] to 1.
1
GPWIO1 SMI Status. Indicates whether or not an SMI was caused by a transition on the GPWIO1 pin.
0: No.
1: Yes.
To enable SMI generation:
1) Ensure that GPWIO1 is enabled as an input: F1BAR1+I/O Offset 15h[1] = 0.
2) Set F1BAR1+I/O Offset 15h[5] to 1.
0
GPWIO0 SMI Status. Indicates whether or not an SMI was caused by a transition on the GPWIO0 pin.
0: No.
1: Yes.
To enable SMI generation:
1) Ensure that GPWIO0 is enabled as an input: F1BAR1+I/O Offset 15h[0] = 0.
2) Set F1BAR1+I/O Offset 15h[4] to 1.
AMD Geode™ SC3200 Processor Data Book
223
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description
Index 85h
Second Level PME/SMI Status Mirror Register 2 (RO)
Reset Value: 00h
The bits in this register contain second level status reporting. Top level status is reported in F1BAR0+I/O Offset 00h/02h[0].
This register is called a “Mirror” register since an identical register exists at F0 Index F5h. Reading this register does not clear the status,
while reading its counterpart at F0 Index F5h clears the status at both the second and top levels.
7
Video Idle Timer Timeout. Indicates whether or not an SMI was caused by expiration of Video Idle Timer Count Register
(F0 Index A6h).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 81h[7] to 1.
6
User Defined Device Idle Timer 3 Timeout. Indicates whether or not an SMI was caused by expiration of User Defined
Device 3 Idle Timer Count Register (F0 Index A4h).
0: No
1: Yes
To enable SMI generation, set F0 Index 81h[6] to 1.
5
User Defined Device Idle Timer 2 Timeout. Indicates whether or not an SMI was caused by expiration of User Defined
Device 2 Idle Timer Count Register (F0 Index A2h).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 81h[5] to 1.
4
User Defined Device Idle Timer 1 Timeout. Indicates whether or not an SMI was caused by expiration of User Defined
Device 1 Idle Timer Count Register (F0 Index A0h).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 81h[4] to 1.
3
Keyboard/Mouse Idle Timer Timeout. Indicates whether or not an SMI was caused by expiration of Keyboard/Mouse Idle
Timer Count Register (F0 Index 9Eh).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 81h[3] to 1.
2
Parallel/Serial Idle Timer Timeout. Indicates whether or not an SMI was caused by expiration of Parallel/Serial Port Idle
Timer Count Register (F0 Index 9Ch).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 81h[2] to 1.
1
Floppy Disk Idle Timer Timeout. Indicates whether or not an SMI was caused by expiration of Floppy Disk Idle Timer
Count Register (F0 Index 9Ah).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 81h[1] to 1.
0
Primary Hard Disk Idle Timer Timeout. Indicates whether or not an SMI was caused by expiration of Primary Hard Disk
Idle Timer Count Register (F0 Index 98h).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 81h[0] to 1.
224
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Revision 5.1
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description
Index 86h
Second Level PME/SMI Status Mirror Register 3 (RO)
Reset Value: 00h
The bits in this register contain second level status reporting. Top level status is reported in F1BAR0+I/O Offset 00h/02h[0].
This register is called a “Mirror” register since an identical register exists at F0 Index F6h. Reading this register does not clear the status,
while reading its counterpart at F0 Index F6h clears the status at both the second and top levels.
7
Video Access Trap SMI Status. Indicates whether or not an SMI was caused by a trapped I/O access to the Video I/O
Trap.
0: No.
1: Yes.
To enable SMI generation, set F0 Index 82h[7] to 1.
6
Reserved.
5
Secondary Hard Disk Access Trap SMI Status. Indicates whether or not an SMI was caused by a trapped I/O access to
the secondary hard disk.
0: No.
1: Yes.
To enable SMI generation, set F0 Index 83h[6] to 1.
4
Secondary Hard Disk Idle Timer SMI Status. Indicates whether or not an SMI was caused by expiration of Secondary
Hard Disk Idle Timer Count register (F0 Index ACh).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 83h[7] to 1.
3
Keyboard/Mouse Access Trap SMI Status. Indicates whether or not an SMI was caused by an trapped I/O access to the
keyboard or mouse.
0: No.
1: Yes.
To enable SMI generation, set F0 Index 82h[3] to 1.
2
Parallel/Serial Access Trap SMI Status. Indicates whether or not an SMI was caused by a trapped I/O access to either the
serial or parallel ports.
0: No.
1: Yes.
To enable SMI generation, set F0 Index 82h[2] to 1.
1
Floppy Disk Access Trap SMI Status. Indicates whether or not an SMI was caused by a trapped I/O access to the floppy
disk.
0: No.
1: Yes.
To enable SMI generation, set F0 Index 82h[1] to 1.
0
Primary Hard Disk Access Trap SMI Status. Indicates whether or not an SMI was caused by a trapped I/O access to the
primary hard disk.
0: No.
1: Yes.
To enable SMI generation, set F0 Index 82h[0] to 1.
AMD Geode™ SC3200 Processor Data Book
225
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description
Index 87h
Second Level PME/SMI Status Mirror Register 4 (RO)
Reset Value: 00h
The bits in this register contain second level status reporting. Top level status is reported at F1BAR0+I/O Offset 00h/02h[0].
This register is called a “Mirror” register since an identical register exists at F0 Index F7h. Reading this register does not clear the status,
while reading its counterpart at F0 Index F7h clears the status at both the second and top levels except for bit 7 which has a third level
of SMI status reporting at F0BAR0+I/O 0Ch/1Ch.
7
GPIO Event SMI Status. Indicates whether or not an SMI was caused by a transition of any of the GPIOs (GPIO47-GPIO32
and GPIO15-GPIO0).
0: No.
1: Yes.
To enable SMI generation, set F1BAR1+I/O Offset 0Ch[0] to 0.
F0BAR0+I/O Offset 08h/18h selects which GPIOs are enabled to generate a PME and setting F1BAR1+I/O Offset 0Ch[0] =
0 enables the PME to generate an SMI. In addition, the selected GPIO must be enabled as an input (F0BAR0+I/O Offset
20h and 24h).
The next level (third level) of SMI status is at F0BAR0+I/O 0Ch/1Ch[15:0].
6
Thermal Override SMI Status. Indicates whether or not an SMI was caused by the assertion of THRM#.
0: No.
1: Yes.
To enable SMI generation, set F0 Index 83h[4] to 1.
5:4
3
Reserved. Always reads 0.
SIO PWUREQ SMI Status. Indicates whether or not an SMI was caused by a power-up event from the SIO.
0: No.
1: Yes.
A power-up event is defined as any of the following events/activities:
— RI2#
— SDATA_IN2
— IRRX1 (CEIR)
To enable SMI generation, set F1BAR1+I/O Offset 0Ch[0] to 0.
2
Codec SDATA_IN SMI Status. Indicates whether or not an SMI was caused by AC97 Codec producing a positive edge on
SDATA_IN.
0: No.
1: Yes.
To enable SMI generation, set F0 Index 80h[5] to 1.
1
RTC Alarm (IRQ8#) SMI Status. Indicates whether or not an SMI was caused by an RTC interrupt.
0: No.
1: Yes.
This SMI event can only occur while in 3V Suspend and an RTC interrupt occurs with F1BAR1+I/O Offset 0Ch[0] = 0.
0
ACPI Timer SMI Status. Indicates whether or not an SMI was caused by an ACPI Timer (F1BAR0+I/O Offset 1Ch or
F1BAR1+I/O Offset 1Ch) MSB toggle.
0: No.
1: Yes.
To enable SMI generation, set F0 Index 83h[5] to 1.
Index 88h
7:0
General Purpose Timer 1 Count Register (R/W)
Reset Value: 00h
GPT1_COUNT. This field represents the load value for General Purpose Timer 1. This value can represent either an 8-bit
counter or a 16-bit counter (selected in F0 Index 8Bh[4]). It is loaded into the counter when the timer is enabled (F0 Index
83h[0] = 1). Once enabled, an enabled event (configured in F0 Index 89h[6:0]) reloads the timer.
The counter is decremented with each clock of the configured timebase (1 ms or 1 sec selected at F0 Index 89h[7]). Upon
expiration of the counter, an SMI is generated, and the top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[9].
The second level SMI status is reported at F1BAR0+I/O Offset 04h/06h[0]. Once expired, this counter must be re-initialized
by either disabling and enabling it, or writing a new count value in this register. See Section 6.2.10.3 "Peripheral Power
Management" on page 180 for a discussion on the limitations of producing count error with small values.
226
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Revision 5.1
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description
Index 89h
7
General Purpose Timer 1 Control Register (R/W)
Reset Value: 00h
General Purpose Timer 1 TImebase. Selects timebase for General Purpose Timer 1 (F0 Index 88h).
0: 1 second.
1: 1 millisecond.
6
Re-trigger General Purpose Timer 1 on User Defined Device 3 (UDEF3) Activity.
0: Disable.
1: Enable.
Any access to the configured (memory or I/O) address range for UDEF3 (configured in F0 Index C8h and CEh) reloads
General Purpose Timer 1.
5
Re-trigger General Purpose Timer 1 on User Defined Device 2 (UDEF2) Activity.
0: Disable.
1: Enable.
Any access to the configured (memory or I/O) address range for UDEF2 (configured in F0 Index C4h and CDh) reloads
General Purpose Timer 1.
4
Re-trigger General Purpose Timer 1 on User Defined Device 1 (UDEF1) Activity.
0: Disable.
1: Enable.
Any access to the configured (memory or I/O) address range for UDEF1 (configured in F0 Index C0h and CCh) reloads
General Purpose Timer 1.
3
Re-trigger General Purpose Timer 1 on Keyboard or Mouse Activity.
0: Disable.
1: Enable.
Any access to the keyboard or mouse I/O address range listed below reloads General Purpose Timer 1:
— Keyboard Controller: I/O Ports 060h/064h.
— COM1: I/O Port 3F8h-3FFh (if F0 Index 93h[1:0] = 10 this range is included).
— COM2: I/O Port 2F8h-2FFh (if F0 Index 93h[1:0] = 11 this range is included).
2
Re-trigger General Purpose Timer 1 on Parallel/Serial Port Activity.
0: Disable.
1: Enable.
Any access to the parallel or serial port I/O address range listed below reloads the General Purpose Timer 1:
— LPT1: I/O Port 3BCh-3BEh.
— LPT2: I/O Port 378h-37Fh.
— COM1: I/O Port 3F8h-3FFh (if F0 Index 93h[1:0] = 10 this range is excluded).
— COM2: I/O Port 2F8h-2FFh (if F0 Index 93h[1:0] = 11 this range is excluded).
— COM3: I/O Port 3E8h-3EFh.
— COM4: I/O Port 2E8h-2EFh.
1
Re-trigger General Purpose Timer 1 on Floppy Disk Activity.
0: Disable.
1: Enable.
Any access to the floppy disk drive address ranges listed below reloads General Purpose Timer 1:
— Primary floppy disk: I/O Port 3F2h-3F5h, 3F7h
— Secondary floppy disk: I/O Port 372h-375h, 377h
The active floppy disk drive is configured via F0 Index 93h[7].
0
Re-trigger General Purpose Timer 1 on Primary Hard Disk Activity.
0: Disable.
1: Enable.
Any access to the primary hard disk address range selected in F0 Index 93h[5], reloads General Purpose Timer 1.
AMD Geode™ SC3200 Processor Data Book
227
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description
Index 8Ah
7:0
General Purpose Timer 2 Count Register (R/W)
Reset Value: 00h
GPT2_COUNT. This field represents the load value for General Purpose Timer 2. This value can represent either an 8-bit or
16-bit counter (configured in F0 Index 8Bh[5]). It is loaded into the counter when the timer is enabled (F0 Index 83h[1] = 1).
Once the timer is enabled and a transition occurs on GPIO7, the timer is re-loaded.
The counter is decremented with each clock of the configured timebase (1 ms or 1 sec selected at F0 Index 8Bh[3]). Upon
expiration of the counter, an SMI is generated and the top level of status is F1BAR0+I/O Offset 00h/02h[9]. The second
level of status is reported at F1BAR0+I/O Offset 04h/06h[1]). Once expired, this counter must be re-initialized by either disabling and enabling it, or by writing a new count value in this register. Section 6.2.10.3 "Peripheral Power Management" on
page 180 for a discussion on the limitations of producing count error with small values.
For GPIO7 to act as the reload for this counter, it must be enabled as such (F0 Index 8Bh[2]) and be configured as an input.
(GPIO pin programming is at F0BAR0+I/O Offset 20h and 24h.)
Index 8Bh
7
General Purpose Timer 2 Control Register (R/W)
Reset Value: 00h
Re-trigger General Purpose Timer 1 (GP Timer 1) on Secondary Hard Disk Activity.
0: Disable.
1: Enable.
Any access to the secondary hard disk address range selected in F0 Index 93h[4] reloads GP Timer 1.
6
VGA Timer Base. Selects timebase for VGA Timer Register (F0 Index 8Eh).
0: 1 millisecond.
1: 32 microseconds.
5
General Purpose Timer 2 (GP Timer 2) Shift. GP Timer 2 is treated as an 8-bit or 16-bit timer.
0: 8-bit. The count value is loaded into GP Timer 2 Count Register (F0 Index 8Ah).
1: 16-bit. The value loaded into GP Timer 2 Count Register is shifted left by eight bits, the lower eight bits become zero,
and this 16-bit value is used as the count for GP Timer 2.
4
General Purpose Timer 1 (GP Timer 1) Shift. GP Timer 1 is treated as an 8-bit or 16-bit timer.
0: 8-bit. The count value is that loaded into GP Timer 1 Count Register (F0 Index 88h).
1: 16-bit. The value loaded into GP Timer 1 Count Register is shifted left by eight bit, the lower eight bits become zero, and
this 16-bit value is used as the count for GP Timer 1.
3
General Purpose Timer 2 (GP Timer 2) Timebase. Selects timebase for GP Timer 2 (F0 Index 8Ah).
0: 1 second.
1: 1 millisecond.
2
Re-trigger Timer on GPIO7 Pin Transition. A rising-edge transition on the GPIO7 pin reloads GP Timer 2 (F0 Index 8Ah).
0: Disable.
1: Enable.
For GPIO7 to work here, it must first be configured as an input. (GPIO pin programming is at F0BAR0+I/O Offset 20h and
24h.)
1:0
Index 8Ch
7:0
Reserved. Set to 0.
IRQ Speedup Timer Count Register (R/W)
Reset Value: 00h
IRQ Speedup Timer Load Value. This field represents the load value for the IRQ speedup timer. It is loaded into the
counter when Suspend Modulation is enabled (F0 Index 96h[0] = 1) and an INTR or an access to I/O Port 061h occurs.
When the event occurs, the Suspend Modulation logic is inhibited, permitting full performance operation of the GX1 module.
Upon expiration, no SMI is generated; the Suspend Modulation begins again. The IRQ speedup timer’s timebase is 1 ms.
This speedup mechanism allows instantaneous response to system interrupts for full-speed interrupt processing. A typical
value here would be 2 to 4 ms.
Index 8Dh
7:0
Video Speedup Timer Count Register (R/W)
Reset Value: 00h
Video Speedup Timer Load Value. This field represents the load value for the Video speedup timer. It is loaded into the
counter when Suspend Modulation is enabled (F0 Index 96[0] = 1) and any access to the graphics controller occurs. When
a video access occurs, the Suspend Modulation logic is inhibited, permitting full-performance operation of the GX1 module.
Upon expiration, no SMI is generated, and Suspend Modulation begins again. The video speedup timer’s timebase is 1 ms.
This speedup mechanism allows instantaneous response to video activity for full speed during video processing calculations. A typical value here would be 50 ms to 100 ms.
228
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Revision 5.1
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description
Index 8Eh
7:0
VGA Timer Count Register (R/W)
Note:
Although grouped with the power management Idle Timers, the VGA Timer is not a power management function.
It is not affected by the Global Power Management Enable setting at F0 Index 80h[0].
Index 8Fh-92h
Index 93h
7
Reset Value: 00h
VGA Timer Load Value. This field represents the load value for VGA Timer. It is loaded into the counter when the timer is
enabled (F0 Index 83h[3] = 1). The counter is decremented with each clock of the configured timebase (F0 Index 8Bh[6]).
Upon expiration of the counter, an SMI is generated and the status is reported at F1BAR0+I/O Offset 00h/02h[6] (only).
Once expired, this counter must be re-initialized by either disabling and enabling it, or by writing a new count value in this
register.
Reserved
Reset Value: 00h
Miscellaneous Device Control Register (R/W)
Reset Value: 00h
Floppy Drive Port Select. Indicates whether all system resources used to power manage the floppy drive use the primary,
or secondary FDC addresses for decode.
0: Secondary.
1: Primary.
6
Reserved. Must be set to 1.
5
Partial Primary Hard Disk Decode. This bit is used to restrict the addresses which are decoded as primary hard disk
accesses.
0: Power management monitors all reads and writes to I/O Port 1F0h-1F7h, 3F6h-3F7h (excludes writes to 3F7h), and
170h-177h, 376h-377h (excludes writes to 377h).
1: Power management monitors only writes to I/O Port 1F6h and 1F7h.
4
Partial Secondary Hard Disk Decode. This bit is used to restrict the addresses which are decoded as secondary hard disk
accesses.
0: Power management monitors all reads and writes to I/O Port 170h-177h, 376h-377h (excludes writes to 377h).
1: Power management monitors only writes to I/O Port 176h and 177h.
3:2
1
Reserved. Must be set to 0.
Mouse on Serial Enable. Mouse is present on a Serial Port.
0: No.
1: Yes.
If a mouse is attached to a serial port (i.e., this bit is set to 1), that port is removed from the serial device list being used to
monitor serial port access for power management purposes and added to the keyboard/mouse decode. This is done
because a mouse, along with the keyboard, is considered an input device and is used only to determine when to blank the
screen.
This bit and bit 0 of this register determine the decode used for the Keyboard/Mouse Idle Timer Count Register (F0 Index
9Eh) as well as the Parallel/Serial Port Idle Timer Count Register (F0 Index 9Ch).
0
Mouse Port Select. Selects which serial port the mouse is attached to:
0: COM1
1: COM2.
For more information see the description of bit 1 in this register (above).
Index 94h-95h
15:8
Suspend Modulation Register (R/W)
Reset Value: 0000h
Suspend Signal Asserted Counter. This 8-bit counter represents the number of 32 µs intervals that the internal SUSP#
signal is asserted to the GX1 module. Together with bits [7:0], perform the Suspend Modulation function for CPU power
management. The ratio of SUSP# asserted-to-de-asserted sets up an effective (emulated) clock frequency, allowing the
power manager to reduce GX1 module power consumption.
This counter is prematurely reset if an enabled speedup event occurs (i.e., IRQ and video speedups).
7:0
Suspend Signal De-asserted Counter. This 8-bit counter represents the number of 32 µs intervals that the internal SUSP#
signal is de-asserted to the GX1 module. Together with bits [15:8], perform the Suspend Modulation function for CPU power
management. The ratio of SUSP# asserted-to-de-asserted sets up an effective (emulated) clock frequency, allowing the
power manager to reduce GX1 module power consumption.
This counter is prematurely reset if an enabled speedup event occurs (i.e., IRQ and video speedups).
AMD Geode™ SC3200 Processor Data Book
229
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description
Index 96h
7:3
2
Suspend Configuration Register (R/W)
Reset Value: 00h
Reserved. Must be set to 0.
Suspend Mode Configuration. Special 3V Suspend mode to support powering down the GX1 module during Suspend.
0: Disable.
1: Enable.
1
SMI Speedup Configuration. Selects how the Suspend Modulation function should react when an SMI occurs.
0: Use the IRQ Speedup Timer Count Register (F0 Index 8Ch) to temporarily disable Suspend Modulation when an SMI
occurs.
1: Disable Suspend Modulation when an SMI occurs until a read to the SMI Speedup Disable Register (F1BAR0+I/O Offset
08h).
The purpose of this bit is to disable Suspend Modulation while the GX1 module is in the System Management Mode so that
VSA and Power Management operations occur at full speed. Two methods for accomplishing this are:
Map the SMI into the IRQ Speedup Timer Count Register (F0 Index 8Ch).
- or Have the SMI disable Suspend Modulation until the SMI handler reads the SMI Speedup Disable Register (F1BAR0+I/O
Offset 08h). This the preferred method.
This bit has no affect if the Suspend Modulation feature is disabled (bit 0 = 0).
0
Suspend Modulation Feature Enable. This bit is used to enable/disable the Suspend Modulation feature.
0: Disable.
1: Enable.
When enabled, the internal SUSP# signal is asserted and de-asserted for the durations programmed in the Suspend Modulation register (F0 Index 94h).
The setting of this bit is mirrored in the Top Level PME/SMI Status register (F1BAR0+I/O Offset 00h/02h[15]. It is used by
the SMI handler to determine if the SMI Speedup Disable register (F1BAR0+I/O Offset 08h) must be cleared on exit.
Index 97h
Reserved
Index 98h-99h
15:0
Reset Value: 00h
Primary Hard Disk Idle Timer Count Register (Primary Channel) (R/W)
Reset Value: 0000h
Primary Hard Disk Idle Timer Count. This idle timer is used to determine when the primary hard disk is not in use so that
it can be powered down. The 16-bit value programmed here represents the period of hard disk inactivity after which the system is alerted via an SMI. The timer is automatically reloaded with the count value whenever an access occurs to the configured hard disk’s data port (I/O port 1F0h or 3F6h).
This counter uses a 1 second timebase. To enable this timer, set F0 Index 81h[0] = 1.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 85h/F5h[0].
Index 9Ah-9Bh
15:0
Floppy Disk Idle Timer Count Register (R/W)
Reset Value: 0000h
Floppy Disk Idle Timer Count. This idle timer is used to determine when the floppy disk drive is not in use so that it can be
powered down. The 16-bit value programmed here represents the period of floppy disk drive inactivity after which the system is alerted via an SMI. The timer is automatically reloaded with the count value whenever an access occurs to the configured floppy drive’s data port (I/O port 3F5h or 375h).
This counter uses a 1 second time base. To enable this timer, set F0 Index 81h[1] = 1.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 85h/F5h[1].
Index 9Ch-9Dh
15:0
Parallel / Serial Idle Timer Count Register (R/W)
Reset Value: 0000h
Parallel / Serial Idle Timer Count. This idle timer is used to determine when the parallel and serial ports are not in use so
that the ports can be power managed. The 16-bit value programmed in this register represents the period of inactivity for
these ports after which the system is alerted via an SMI. The timer is automatically reloaded with the count value whenever
an access occurs to the parallel (LPT) or serial (COM) I/O address spaces. If the mouse is enabled on a serial port, that port
is not considered here.
This counter uses a 1 second timebase. To enable this timer, set F0 Index 81h[2] = 1.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 85h/F5h[2].
230
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Revision 5.1
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description
Index 9Eh-9Fh
15:0
Keyboard / Mouse Idle Timer Count Register (R/W)
Reset Value: 0000h
Keyboard / Mouse Idle Timer Count. This idle timer determines when the keyboard and mouse are not in use so that the
LCD screen can be blanked. The 16-bit value programmed in this register represents the period of inactivity for these ports
after which the system is alerted via an SMI. The timer is automatically reloaded with the count value whenever an access
occurs to either the keyboard or mouse I/O address spaces (including the mouse serial port address space when a mouse
is enabled on a serial port.)
This counter uses a 1 second time base. To enable this timer, set F0 Index 81h[3] = 1.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 85h/F5h[3].
Index A0h-A1h
15:0
User Defined Device 1 Idle Timer Count Register (R/W)
Reset Value: 0000h
User Defined Device 1 (UDEF1) Idle Timer Count. This idle timer determines when the device configured as User Defined
Device 1 (UDEF1) is not in use so that it can be power managed. The 16-bit value programmed in this register represents
the period of inactivity for this device after which the system is alerted via an SMI. The timer is automatically reloaded with
the count value whenever an access occurs to memory or I/O address space configured in the F0 Index C0h (Base Address
register) and F0 Index CCh (Control register).
This counter uses a 1 second time base. To enable this timer, set F0 Index 81h[4] = 1.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 85h/F5h[4].
Index A2h-A3h
15:0
User Defined Device 2 Idle Timer Count Register (R/W)
Reset Value: 0000h
User Defined Device 2 (UDEF2) Idle Timer Count. This idle timer determines when the device configured as UDEF2 is not
in use so that it can be power managed. The 16-bit value programmed in this register represents the period of inactivity for
this device after which the system is alerted via an SMI. The timer is automatically reloaded with the count value whenever
an access occurs to memory or I/O address space configured in the F0 Index C4h (Base Address register) and F0 Index
CDh (Control register).
This counter uses a 1 second timebase. To enable this timer, set F0 Index 81h[5] = 1.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 85h/F5h[5].
Index A4h-A5h
15:0
User Defined Device 3 Idle Timer Count Register (R/W)
Reset Value: 0000h
User Defined Device 3 (UDEF3) Idle Timer Count. This idle timer determines when the device configured as UDEF3 is not
in use so that it can be power managed. The 16-bit value programmed in this register represents the period of inactivity for
this device after which the system is alerted via an SMI. The timer is automatically reloaded with the count value whenever
an access occurs to memory or I/O address space configured in the UDEF3 Base Address Register (F0 Index C8h) and
UDEF3 Control Register (F0 Index CEh).
This counter uses a 1 second timebase. To enable this timer, set F0 Index 81h[6] = 1.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 85h/F5h[6].
Index A6h-A7h
15:0
Video Idle Timer Count Register (R/W)
Reset Value: 0000h
Video Idle Timer Count. This idle timer determines when the graphics subsystem has been idle as part of the Suspenddetermination algorithm. The 16-bit value programmed in this register represents the period of video inactivity after which
the system is alerted via an SMI. The count in this timer is automatically reset at any access to the graphics controller
space.
This counter uses a 1 second timebase. To enable this timer, set F0 Index 81h[7] = 1.
Since the graphics controller is embedded in the GX1 module, video activity is communicated to the Core Logic module via
the serial connection (PSERIAL register, bit 0). The Core Logic module also detects accesses to standard VGA space on
PCI (3Bxh, 3Cxh, 3Dxh and A000h-B7FFh) if an external VGA controller is being used.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 85h/F5h[7].
Index A8h-A9h
15:0
Video Overflow Count Register (R/W)
Reset Value: 0000h
Video Overflow Count. Each time the video speedup counter is triggered, a 100 ms timer is started. If the 100 ms timer
expires before the video speedup counter lapses, the Video Overflow Count register increments and the 100 ms timer retriggers. Software clears the overflow register when new evaluations are to begin. The count contained in this register can be
combined with other data to determine the type of video accesses present in the system.
Index AAh-ABh
AMD Geode™ SC3200 Processor Data Book
Reserved
Reset Value: 00h
231
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description
Index ACh-ADh
15:0
Secondary Hard Disk Idle Timer Count Register (R/W)
Reset Value: 0000h
Secondary Hard Disk Idle Timer Count. This idle timer is used to determine when the secondary hard disk is not in use so
that it can be powered down. The 16-bit value programmed in this register represents the period of hard disk inactivity after
which the system is alerted via an SMI. The timer is automatically reloaded with the count value whenever an access occurs
to the configured hard disk’s data port (I/O port 1F0h or 170h).
This counter uses a 1 second timebase. To enable this timer, set F0 Index 83h[7] = 1.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 86h/F6h[4].
Index AEh
7:0
CPU Suspend Command Register (WO)
Reset Value: 00h
Software CPU Suspend Command. If bit 0 in the Clock Stop Control register is set low (F0 Index BCh[0] = 0), a write to
this register causes an internal SUSP#/SUSPA# handshake with the GX1 module, placing the GX1 module in a low-power
state. The actual data written is irrelevant. Once in this state, any unmasked IRQ or SMI releases the GX1 module halt condition.
If F0 Index BCh[0] = 1, writing to this register invokes a full system Suspend. In this case, the internal SUSP_3V signal is
asserted after the SUSP#/SUSPA# halt. Upon a Resume event, the PLL delay programmed in the F0 Index BCh[7:4] is
invoked, allowing the clock chip and GX1 module PLL to stabilize before de-asserting SUSP#.
Index AFh
7:0
Suspend Notebook Command Register (WO)
Reset Value: 00h
Software CPU Stop Clock Suspend. A write to this register causes a SUSP#/SUSPA# handshake with the CPU, placing
the GX1 module in a low-power state. Following this handshake, the SUSP_3V signal is asserted. The SUSP_3V signal is
intended to be used to stop all system clocks.
Upon a Resume event, the internal SUSP_3V signal is de-asserted. After a slight delay, the Core Logic module de-asserts
the SUSP# signal. Once the clocks are stable, the GX1 module de-asserts SUSPA# and system operation resumes.
Index B0h-B3h
Index B4h
7:0
Reserved
Reset Value: 00h
Floppy Port 3F2h Shadow Register (RO)
Reset Value: xxh
Floppy Port 3F2h Shadow. Last written value of I/O Port 3F2h. Required for support of FDC power On/Off and 0V Suspend/Resume coherency.
This register is a copy of an I/O register which cannot safely be directly read. The value in this register is not deterministic of
when the register is being read. It is provided here to assist in a Suspend-to-Disk operation.
Index B5h
7:0
Floppy Port 3F7h Shadow Register (RO)
Reset Value: xxh
Floppy Port 3F7h Shadow. Last written value of I/O Port 3F7h. Required for support of FDC power On/Off and 0V Suspend/Resume coherency.
This register is a copy of an I/O register which cannot safely be directly read. The value in this register is not deterministic of
when the register is being read. It is provided here to assist in a Suspend-to-Disk operation.
Index B6h
7:0
Floppy Port 372h Shadow Register (RO)
Reset Value: xxh
Floppy Port 372h Shadow. Last written value of I/O Port 372h. Required for support of FDC power On/Off and 0V Suspend/Resume coherency.
This register is a copy of an I/O register which cannot safely be directly read. The value in this register is not deterministic of
when the register is being read. It is provided here to assist in a Suspend-to-Disk operation.
Index B7h
7:0
Floppy Port 377h Shadow Register (RO)
Reset Value: xxh
Floppy Port 377h Shadow. Last written value of I/O Port 377h. Required for support of FDC power On/Off and 0V Suspend/Resume coherency.
This register is a copy of an I/O register which cannot safely be directly read. The value in this register is not deterministic of
when the register is being read. It is provided here to assist in a Suspend-to-Disk operation.
232
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Revision 5.1
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description
Index B8h
7:0
DMA Shadow Register (RO)
Reset Value: xxh
DMA Shadow. This 8-bit port sequences through the following list of shadowed DMA Controller registers. At power on, a
pointer starts at the first register in the list and continuing through the other registers in subsequent reads according to the
read sequence. A write to this register resets the read sequence to the first register. Each shadow register in the sequence
contains the last data written to that location.
The read sequence for this register is:
1. DMA Channel 0 Mode Register
2. DMA Channel 1 Mode Register
3. DMA Channel 2 Mode Register
4. DMA Channel 3 Mode Register
5. DMA Channel 4 Mode Register
6. DMA Channel 5 Mode Register
7. DMA Channel 6 Mode Register
8. DMA Channel 7 Mode Register
9. DMA Channel Mask Register (bit 0 is channel 0 mask, etc.)
10. DMA Busy Register (bit 0 or 1 means a DMA occurred within last 1 ms, all other bits are 0)
Index B9h
7:0
PIC Shadow Register (RO)
Reset Value: xxh
PIC Shadow. This 8-bit port sequences through the following list of shadowed Interrupt Controller registers. At power on, a
pointer starts at the first register in the list and continuing through the other registers in subsequent reads according to the
read sequence. A write to this register resets the read sequence to the first register. Each shadow register in the sequence
contains the last data written to that location.
The read sequence for this register is:
1. PIC1 ICW1
2. PIC1 ICW2
3. PIC1 ICW3
4. PIC1 ICW4 - Bits [7:5] of ICW4 are always 0.
5. PIC1 OCW2 - Bits [6:3] of OCW2 are always 0 (See Note).
6. PIC1 OCW3 - Bits [7:4] are 0 and bits [6:3] are 1.
7. PIC2 ICW1
8. PIC2 ICW2
9. PIC2 ICW3
10. PIC2 ICW4 - Bits [7:5] of ICW4 are always 0.
11. PIC2 OCW2 - Bits [6:3] of OCW2 are always 0 (See Note).
12. PIC2 OCW3 - Bits [7:4] are 0 and bits [6:3] are 1.
Note:
To restore OCW2 to the shadow register value, write the appropriate address twice. First with the shadow register
value, then with the shadow register value ORed with C0h.
Index BAh
7:0
PIT Shadow Register (RO)
Reset Value: xxh
PIT Shadow. This 8-bit port sequences through the following list of shadowed Programmable Interval Timer registers. At
power on, a pointer starts at the first register in the list and continuing through the other registers in subsequent reads
according to the read sequence. A write to this register resets the read sequence to the first register. Each shadow register
in the sequence contains the last data written to that location.
The read sequence for this register is:
1. Counter 0 LSB (least significant byte)
2. Counter 0 MSB
3. Counter 1 LSB
4. Counter 1 MSB
5. Counter 2 LSB
6. Counter 2 MSB
7. Counter 0 Command Word
8. Counter 1 Command Word
9. Counter 2 Command Word
Note:
The LSB/MSB of the count is the Counter base value, not the current value.
Bits [7:6] of the command words are not used.
AMD Geode™ SC3200 Processor Data Book
233
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description
Index BBh
7:0
RTC Index Shadow Register (RO)
Index BCh
7:4
Clock Stop Control Register (R/W)
0
Reset Value: 00h
PLL Delay. The programmed value in this field sets the delay (in milliseconds) after a break event occurs before the internal
SUSP# signal is de-asserted to the GX1 module. This delay is designed to allow the clock chip and CPU PLL to stabilize
before starting execution. This delay is only invoked if the STP_CLK bit was set.
The 4-bit field allows values from 0 to 15 ms.
0000: 0 ms
0100: 4 ms
0001: 1 ms
0101: 5 ms
0010: 2 ms
0110: 6 ms
0011: 3 ms
0111: 7 ms
3:1
Reset Value: xxh
RTC Index Shadow. The RTC Shadow register contains the last written value of the RTC Index register (I/O Port 070h).
1000: 8 ms
1001: 9 ms
1010: 10 ms
1011: 11 ms
1100: 12 ms
1101: 13 ms
1110: 14 ms
1111: 15 ms
Reserved. Set to 0.
CPU Clock Stop.
0: Normal internal SUSP#/SUSPA# handshake.
1: Full system Suspend.
Note:
This register configures the Core Logic module to support a 3V Suspend mode. Setting bit 0 causes the SUSP_3V signal to
assert after the appropriate conditions, stopping the system clocks. A delay of 0-15 ms is programmable (bits [7:4]) to allow for
a delay for the clock chip and CPU PLL to stabilize when an event Resumes the system.
A write to the CPU Suspend Command register (F0 Index AEh) with bit 0 written as:
0: Internal SUSP#/SUSPA# handshake occurs. The GX1 module is put into a low-power state, and the system clocks are not
stopped. When a break/resume event occurs, it releases the CPU halt condition.
1: Internal SUSP#/SUSPA# handshake occurs and the SUSP_3V signal is asserted, thus invoking a full system Suspend (both
GX1 module and system clocks are stopped). When a break event occurs, the SUSP_3V signal is de-asserted, the PLL delay
programmed in bits [7:4] are invoked which allows the clock chip and GX1 module PLL to stabilize before de-asserting the
internal SUSP# signal.
Index BDh-BFh
Reserved
Index C0h-C3h
User Defined Device 1 Base Address Register (R/W)
31:0
Reset Value: 00h
Reset Value: 00000000h
User Defined Device 1 Base Address. This 32-bit register supports power management (Trap and Idle timer resources)
for a PCMCIA slot or some other device in the system. The value in this register is used as the address comparator for the
device trap/timer logic. The device can be memory or I/O mapped (configured in F0 Index CCh).
The Core Logic module cannot snoop addresses on the Fast-PCI bus unless it actually claims the cycle. Therefore, Traps
and Idle timers cannot support power management of devices on the Fast-PCI bus.
Index C4h-C7h
31:0
User Defined Device 2 Base Address Register (R/W)
Reset Value: 00000000h
User Defined Device 2 Base Address. This 32-bit register supports power management (Trap and Idle timer resources)
for a PCMCIA slot or some other device in the system. The value in this register is used as the address comparator for the
device trap/timer logic. The device can be memory or I/O mapped (configured in F0 Index CDh).
The Core Logic module cannot snoop addresses on the Fast-PCI bus unless it actually claims the cycle. Therefore, Traps
and Idle timers cannot support power management of devices on the Fast-PCI bus.
Index C8h-CBh
31:0
User Defined Device 3 Base Address Register (R/W)
Reset Value: 00000000h
User Defined Device 3 Base Address. This 32-bit register supports power management (Trap and Idle timer resources)
for a PCMCIA slot or some other device in the system. The value in this register is used as the address comparator for the
device trap/timer logic. The device can be memory or I/O mapped (configured in F0 Index CEh).
The Core Logic module cannot snoop addresses on the Fast-PCI bus unless the it actually claims the cycle. Therefore,
Traps and Idle timers cannot support power management of devices on the Fast-PCI bus.
234
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Revision 5.1
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description
Index CCh
7
User Defined Device 1 Control Register (R/W)
Reset Value: 00h
Memory or I/O Mapped. Determines how User Defined Device 1 is mapped.
0: I/O.
1: Memory.
6:0
Mask.
If bit 7 = 0 (I/O):
Bit 6
0: Disable write cycle tracking
1: Enable write cycle tracking
Bit 5
0: Disable read cycle tracking
1: Enable read cycle tracking
Bits [4:0] Mask for address bits A[4:0]
If bit 7 = 1 (Memory):
Bits [6:0] Mask for address memory bits A[15:9] (512 bytes min. and 64 KB max.) A[8:0] are ignored.
Note:
A "1" in a mask bit means that the address bit is ignored for comparison.
Index CDh
7
User Defined Device 2 Control Register (R/W)
Reset Value: 00h
Memory or I/O Mapped. determines how User Defined Device 2 is mapped.
0: I/O
1: Memory
6:0
Mask.
If bit 7 = 0 (I/O):
Bit 6
0: Disable write cycle tracking
1: Enable write cycle tracking
Bit 5
0: Disable read cycle tracking
1: Enable read cycle tracking
Bits [4:0] Mask for address bits A[4:0]
If bit 7 = 1 (Memory):
Bits [6:0] Mask for address memory bits A[15:9] (512 bytes min. and 64 KB max.) A[8:0] are ignored.
Note:
A "1" in a mask bit means that the address bit is ignored for comparison.
Index CEh
7
User Defined Device 3 Control Register (R/W)
Reset Value: 00h
Memory or I/O Mapped. Determines how User Defined Device 3 is mapped.
0: I/O.
1: Memory.
6:0
Mask.
If bit 7 = 0 (I/O):
Bit 6
0: Disable write cycle tracking
1: Enable write cycle tracking
Bit 5
0: Disable read cycle tracking
1: Enable read cycle tracking
Bits [4:0] Mask for address bits A[4:0]
If bit 7 = 1 (Memory):
Bits [6:0] Mask for address memory bits A[15:9] (512 bytes min. and 64 KB max.) A[8:0] are ignored.
Note:
A "1" in a mask bit means that the address bit is ignored for comparison.
Index CFh
Reserved
Reset Value: 00h
Index D0h
Software SMI Register (WO)
Reset Value: 00h
7:0
Software SMI. A write to this location generates an SMI. The data written is irrelevant. This register allows software entry
into SMM via normal bus access instructions.
Index D1h-EBh
AMD Geode™ SC3200 Processor Data Book
Reserved
Reset Value: 00h
235
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description
Index ECh
7:0
Timer Test Register (R/W)
Reset Value: 00h
Timer Test Value. The Timer Test register is intended only for test and debug purposes. It is not intended for setting operational timebases. For normal operation, never write to this register.
Index EDh-F3h
Index F4h
Reserved
Reset Value: 00h
Second Level PME/SMI Status Register 1 (RC)
Reset Value: 00h
The bits in this register contain second level status reporting. Top level status is reported in F1BAR0+I/O Offset 00h/02h[0].
Reading this register clears the status at both the second and top levels.
A read-only “Mirror” version of this register exists at F0 Index 84h. If the value of the register must be read without clearing the SMI
source (and consequently de-asserting SMI), F0 Index 84h can be read instead.
7:3
2
Reserved. Reads as 0.
GPWIO2 SMI Status. Indicates whether or not an SMI was caused by a transition on the GPWIO2 pin.
0: No.
1: Yes.
To enable SMI generation:
1) Ensure that GPWIO2 is enabled as an input: F1BAR1+I/O Offset 15h[2] = 0.
2) Set F1BAR1+I/O Offset 15h[6] = 1 to allow SMI generation.
1
GPWIO1 SMI Status. Indicates whether or not an SMI was caused by a transition on the GPWIO1 pin.
0: No.
1: Yes.
To enable SMI generation:
1) Ensure that GPWIO1 is enabled as an input: F1BAR1+I/O Offset 15h[1] = 0.
2) Set F1BAR1+I/O Offset 15h[5] to 1 to allow SMI generation.
0
GPWIO0 SMI Status. Indicates whether or not an SMI was caused by a transition on the GPWIO0 pin.
0: No
1: Yes
To enable SMI generation:
1) Ensure that GPWIO0 is enabled as an input: F1BAR1+I/O Offset 15h[0] = 0.
2) Set F1BAR1+I/O Offset 15h[4] to 1 to allow SMI generation.
Index F5h
Second Level PME/SMI Status Register 2 (RC)
Reset Value: 00h
The bits in this register contain second level status reporting. Top level status is reported in F1BAR0+I/O Offset 00h/02h[0].
Reading this register clears the status at both the second and top levels.
A read-only “Mirror” version of this register exists at F0 Index 85h. If the value of the register must be read without clearing the SMI
source (and consequently de-asserting SMI), F0 Index 85h can be read instead.
7
Video Idle Timer SMI Status. Indicates whether or not an SMI was caused by expiration of Video Idle Timer Count Register, (F0 Index A6h).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 81h[7] = 1.
6
User Defined Device Idle Timer 3 (UDEF3) SMI Status. Indicates whether or not an SMI was caused by expiration of User
Defined Device 3 (UDEF3) Idle Timer Count Register (F0 Index A4h).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 81h[6] = 1.
5
User Defined Device Idle Timer 2 (UDEF2) SMI Status. Indicates whether or not an SMI was caused by expiration of User
Defined Device 2 (UDEF2) Idle Timer Count Register (F0 Index A2h).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 81h[5] = 1.
236
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Revision 5.1
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
4
Description
User Defined Device Idle Timer 1 (UDEF1) SMI Status. Indicates whether or not an SMI was caused by expiration of User
Defined Device 1 (UDEF1) Idle Timer Count Register (F0 Index A0h).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 81h[4] = 1.
3
Keyboard/Mouse Idle Timer SMI Status. Indicates whether or not an SMI was caused by expiration of Keyboard/ Mouse
Idle Timer Count Register (F0 Index 9Eh).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 81h[3] = 1.
2
Parallel/Serial Idle Timer SMI Status. Indicates whether or not an SMI was caused by expiration of Parallel/Serial Port Idle
Timer Count Register (F0 Index 9Ch).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 81h[2] = 1.
1
Floppy Disk Idle Timer SMI Status. Indicates whether or not an SMI was caused by expiration of Floppy Disk Idle Timer
Count Register (F0 Index 9Ah).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 81h[1] = 1.
0
Hard Disk Idle Timer SMI Status. Indicates whether or not an SMI was caused by expiration of Hard Disk Idle Timer Count
Register (F0 Index 98h).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 81h[0] = 1.
Index F6h
Second Level PME/SMI Status Register 3 (RC)
Reset Value: 00h
The bits in this register contain second level status reporting. Top level status is reported in F1BAR0+I/O Offset 00h/02h[0].
Reading this register clears the status at both the second and top levels.
A read-only “Mirror” version of this register exists at F0 Index 86h. If the value of the register must be read without clearing the SMI
source (and consequently de-asserting SMI), F0 Index 86h can be read instead.
7
Video Access Trap SMI Status. Indicates whether or not an SMI was caused by a trapped I/O access to the Video I/O
Trap.
0: No.
1: Yes.
To enable SMI generation, set F0 Index 82h[7] = 1.
6
Reserved. Reads as 0.
5
Secondary Hard Disk Access Trap SMI Status. Indicates whether or not an SMI was caused by a trapped I/O access to
the secondary hard disk.
0: No.
1: Yes.
To enable SMI generation, set F0 Index 83h[6] = 1.
4
Secondary Hard Disk Idle Timer SMI Status. Indicates whether or not an SMI was caused by expiration of Secondary
Hard Disk Idle Timer Count register (F0 Index ACh).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 83h[7] = 1.
AMD Geode™ SC3200 Processor Data Book
237
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
3
Description
Keyboard/Mouse Access Trap SMI Status. Indicates whether or not an SMI was caused by a trapped I/O access to the
keyboard or mouse.
0: No.
1: Yes.
To enable SMI generation, set F0 Index 82h[3] = 1.
2
Parallel/Serial Access Trap SMI Status. Indicates whether or not an SMI was caused by a trapped I/O access to either the
serial or parallel ports.
0: No.
1: Yes.
To enable SMI generation, set F0 Index 82h[2] =1.
1
Floppy Disk Access Trap SMI Status. Indicates whether or not an SMI was caused by a trapped I/O access to the floppy
disk.
0: No.
1: Yes.
To enable SMI generation, set F0 Index 82h[1] = 1.
0
Primary Hard Disk Access Trap SMI Status. Indicates whether or not an SMI was caused by a trapped I/O access to the
primary hard disk.
0: No.
1: Yes.
To enable SMI generation, set F0 Index 82h[0] = 1.
Index F7h
Second Level PME/SMI Status Register 4 (RC)
Reset Value: 00h
The bits in this register contain second level status reporting. Top level status is reported in F1BAR0+I/O Offset 00h/02h[0].
Reading this register clears the status at both the second and top levels except for bit 7 which has a third level of status reporting at
F0BAR0+I/O 0Ch/1Ch.
A read-only “Mirror” version of this register exists at F0 Index 87h. If the value of the register must be read without clearing the SMI
source (and consequently de-asserting SMI), F0 Index 87h can be read instead.
7
GPIO Event SMI Status (Read Only, Read does not Clear). Indicates whether or not an SMI was caused by a transition of
any of the GPIOs (GPIO47-GPIO32 and GPIO15-GPIO0).
0: No.
1: Yes.
To enable SMI generation, set F1BAR1+I/O Offset 0Ch[0] = 0.
F0BAR0+I/O Offset 08h/18h selects which GPIOs are enabled to generate a PME and setting F1BAR1+I/O Offset 0Ch[0] =
0 enables the PME to generate an SMI. In addition, the selected GPIO must be enabled as an input (F0BAR0+I/O Offset
20h and 24h).
The next level (third level) of SMI status is at F0BAR0+I/O 0Ch/1Ch.
6
Thermal Override SMI Status. Indicates whether or not an SMI was caused by an assertion of the THRM#.
0: No.
1: Yes.
To enable SMI generation set F0 Index 83h[4] = 1.
5:4
3
Reserved. Read as 0.
SIO PWUREQ SMI Status. Indicates whether or not an SMI was caused by a power-up event from the SIO.
0: No.
1: Yes.
A power-up event is defined as any of the following events/activities:
— RI2#
— SDATA_IN2
— IRRX1 (CEIR)
To enable SMI generation, set F1BAR1+I/O Offset 0Ch[0] = 0.
238
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Revision 5.1
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
2
Description
Codec SDATA_IN SMI Status. Indicates whether or not an SMI was caused by AC97 Codec producing a positive edge on
SDATA_IN.
0: No.
1: Yes.
To enable SMI generation, set F0 Index 80h[5] = 1.
1
RTC Alarm (IRQ8#) SMI Status. Indicates whether or not an SMI was caused by an RTC interrupt.
0: No.
1: Yes.
This SMI event can only occur while in 3V Suspend and an RTC interrupt occurs and F1BAR1+I/O Offset 0Ch[0] = 0.
0
ACPI Timer SMI Status. Indicates whether or not an SMI was caused by an ACPI Timer (F1BAR0+I/O Offset 1Ch or
F1BAR1+I/O Offset 1Ch) MSB toggle.
0: No.
1: Yes.
To enable SMI generation, set F0 Index 83h[5] = 1.
Index F8h-FFh
AMD Geode™ SC3200 Processor Data Book
Reserved
Reset Value: 00h
239
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
6.4.1.1 GPIO Support Registers
F0 Index 10h, Base Address Register 0 (F0BAR0) points to
the base address of where the GPIO runtime and configu-
ration registers are located. Table 6-29 gives the bit formats of I/O mapped registers accessed through F0BAR0.
Table 6-30. F0BAR0+I/O Offset: GPIO Configuration Registers
Bit
Description
Offset 00h-03h
31:0
GPDO0 — GPIO Data Out 0 Register (R/W)
Reset Value: FFFFFFFFh
GPIO Data Out. Bits [31:0] of this register correspond to GPIO31-GPIO0 signals, respectively. The value of each bit determines the value driven on the corresponding GPIO signal when its output buffer is enabled. Writing to the bit latches the
written data unless the bit is locked by the GPIO Configuration register Lock bit (F0BAR0+I/O Offset 24h[3]). Reading the
bit returns the value, regardless of the signal value and configuration.
0: Corresponding GPIO signal is driven to low when output enabled.
1: Corresponding GPIO signal is driven or released to high (according to buffer type and static pull-up selection) when output is enabled.
Offset 04h-07h
31:0
GPDI0 — GPIO Data In 0 Register (RO)
Reset Value: FFFFFFFFh
GPIO Data In. Bits [31:0] of this register correspond to GPIO31-GPIO0 signals, respectively. Reading each bit returns the
value of the corresponding GPIO signal, regardless of the signal configuration and the GPDO0 register (F0BAR0+I/O Offset
00h) value.
Writes to this register are ignored.
0: Corresponding GPIO signal level is low.
1: Corresponding GPIO signal level is high.
Offset 08h-0Bh
GPIEN0 — GPIO Interrupt Enable 0 Register (R/W)
Reset Value: 00000000h
31:16
Reserved. Must be set to 0.
15:0
GPIO Power Management Event (PME) Enable. Bits [15:0] correspond to GPIO15-GPIO0 signals, respectively. Each bit
allows PME generation by the corresponding GPIO signal.
0: Disable PME generation.
1: Enable PME generation.
Notes: 1) All of the enabled GPIO PMEs are always reported at F1BAR1+I/O Offset 10h[3].
2) Any enabled GPIO PME can be selected to generate an SCI or SMI at F1BAR1+I/O Offset 0Ch[0].
If SCI is selected, then the individually selected GPIO PMEs are globally enabled for SCI generation at
F1BAR1+I/O Offset 12h[3] and the status is reported at F1BAR1+I/O Offset 10h[3].
If SMI is selected, the individually selected GPIO PMEs generate an SMI and the status is reported at
F1BAR0+I/O Offset 00h/02h[0].
Offset 0Ch-0Fh
GPST0 — GPIO Status 0 Register (R/W1C)
Reset Value: 00000000h
31:16
Reserved. Must be set to 0.
15:0
GPIO Status. Bits [15:0] correspond to GPIO15-GPIO0 signals, respectively. Each bit reports a 1 when hardware detects
the edge (rising/falling on the GPIO signal) that is programmed in F0BAR0+I/O Offset 24h[5]. If the corresponding bit in
F0BAR0+I/O Offset 08h is set, this edge generates a PME.
0: No active edge detected since the bit was last cleared.
1: Active edge detected.
Writing 1 to the a Status bit clears it to 0.
This is the third level of SMI status reporting to the second level at F0 Index 87h/F7h[7] and the top level at F1BAR0+I/O
Offset 00h/02h[0]. Clearing the third level also clears the second and top levels.
This is the second level of SCI status reporting to the top level at F1BAR1+Offset 10h[3]. The status must be cleared at
both the this level and the top level (i.e., the top level is not automatically cleared when a bit in this register is cleared).
240
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Revision 5.1
Table 6-30. F0BAR0+I/O Offset: GPIO Configuration Registers (Continued)
Bit
Description
Offset 10h-13h
31:0
GPDO1 — GPIO Data Out 1 Register (R/W)
Reset Value: FFFFFFFFh
GPIO Data Out. Bits [31:0] of this register correspond to GPIO63-GPIO32 signals, respectively. The value of each bit
determines the value driven on the corresponding GPIO signal when its output buffer is enabled. Writing to the bit latches
the written data unless the bit is locked by the GPIO Configuration register Lock bit (F0BAR0+I/O Offset 24h[3]). Reading
the bit returns the value, regardless of the signal value and configuration.
0: Corresponding GPIO signal driven to low when output enabled.
1: Corresponding GPIO signal driven or released to high (according to buffer type and static pull-up selection) when output
enabled.
Offset 14h-17h
31:0
GPDI1 — GPIO Data In 1 Register (RO)
Reset Value: FFFFFFFFh
GPIO Data In. Bits [31:0] of this register correspond to GPIO63-GPIO32 signals, respectively. Reading each bit returns the
value of the corresponding GPIO signal, regardless of the signal configuration and the GPDO1 register (F0BAR0+I/O Offset
10h) value. Writes to this register are ignored.
0: Corresponding GPIO signal level low.
1: Corresponding GPIO signal level high.
Offset 18h-1Bh
GPIEN1 — GPIO Interrupt Enable 1 Register (R/W)
Reset Value: 00000000h
31:16
Reserved. Must be set to 0.
15:0
GPIO Power Management Event (PME) Enable. Bits [15:0] of this register correspond to GPIO47-GPIO32 signals,
respectively. Each bit allows PME generation by the corresponding GPIO signal.
0: Disable PME generation.
1: Enable PME generation.
Notes: 1) All of the enabled GPIO PMEs are always reported at F1BAR1+I/O Offset 10h[3].
2) Any enabled GPIO PME can be selected to generate an SCI or SMI at F1BAR1+I/O Offset 0Ch[0].
If SCI is selected, the individually selected GPIO PMEs are globally enabled for SCI generation at F1BAR1+I/
O Offset 12h[3] and the status is reported at F1BAR1+I/O Offset 10h[3].
If SMI is selected, the individually selected GPIO PMEs generate an SMI and the status is reported at
F1BAR0+I/O Offset 00h/02h[0].
Offset 1Ch-1Fh
GPST1 — GPIO Status 1 Register (R/W1C)
Reset Value: 00000000h
31:16
Reserved. Must be set to 0.
15:0
GPIO Status. Bits [15:0] correspond to GPIO47-GPIO32 signals, respectively. Each bit reports a 1 when hardware detects
the edge (rising/falling on the GPIO signal) that is programmed in F0BAR0+I/O Offset 24h[5]. If the corresponding bit in
F0BAR0+I/O Offset 18h is set, this edge generates a PME.
0: No active edge detected since the bit was last cleared.
1: Active edge detected.
Writing 1 to the a Status bit clears it to 0.
This is the third level of SMI status reporting to the second level at F0 Index 87h/F7h[7] and the top level at F1BAR0+I/O
Offset 00h/02h[0]. Clearing the third level also clears the second and top levels.
This is the second level of SCI status reporting to the top level at F1BAR1+Offset 10h[3]. The status must be cleared at
both the this level and the top level (i.e., the top level is not automatically cleared when a bit in this register is cleared).
Offset 20h-23h
31:6
GPIO Signal Configuration Select Register (R/W)
Reset Value: 00000000h
Reserved. Must be set to 0.
AMD Geode™ SC3200 Processor Data Book
241
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Table 6-30. F0BAR0+I/O Offset: GPIO Configuration Registers (Continued)
Bit
Description
5:0
Signal Select. Selects the GPIO signal to be configured in the Bank selected via bit 5 setting (i.e., Bank 0 or Bank 1). See
Table 4-2 on page 88 for GPIO ball muxing options. GPIOs without an associated ball number are not available externally.
Bank 0
000000 = GPIO0 (EBGA: H1 / TEPBGA: D11)
000001 = GPIO1 (EBGA: H2, AL12 / TEPBGA: D10, N30)
000010 = GPIO2
000011 = GPIO3
000100 = GPIO4
000101 = GPIO5
000110 = GPIO6 (EBGA: AH3 / TEPBGA: D28)
000111 = GPIO7 (EBGA: AH4 / TEPBGA: C30)
001000 = GPIO8 (EBGA: AJ2 / TEPBGA: C31)
001001 = GPIO9 (EBGA: AG4 / TEPBGA: C28)
001010 = GPIO10 (EBGA: AJ1 / TEPBGA: B29)
001011 = GPIO11 (EBGA: H30 / TEPBGA: AJ8)
001100 = GPIO12 (EBGA: AJ12 / TEPBGA: N29)
001101 = GPIO13 (EBGA: AL11 / TEPBGA: M29)
001110 = GPIO14 (EBGA: F1 / TEPBGA: D9)
001111 = GPIO15 (EBGA: G3 / TEPBGA: A8)
010000 = GPIO16 (EBGA: AL15 / TEPBGA: V31)
010001 = GPIO17 (EBGA: J4 / TEPBGA: A10)
010010 = GPIO18 (EBGA: A28 / TEPBGA: AG1)
010011 = GPIO19 (EBGA: H4 / TEPBGA: C9)
010100 = GPIO20 (EBGA: H3, AJ13 / TEPBGA: A9, N31)
010101 = GPIO21
010110 = GPIO22
010111 = GPIO23
011000 = GPIO24
011001 = GPIO25
011010 = GPIO26
011011 = GPIO27
011100 = GPIO28
011101 = GPIO29
011110 = GPIO30
011111 = GPIO31
Bank 1
100000 = GPIO32 (EBGA: AJ11 / TEPBGA: M28)
100001 = GPIO33 (EBGA: AL10 / TEPBGA: L31)
100010 = GPIO34 (EBGA: AK10 / TEPBGA: L30)
100011 = GPIO35 (EBGA: AJ10 / TEPBGA: L29)
100100 = GPIO36 (EBGA: AL9 / TEPBGA: L28)
100101 = GPIO37 (EBGA: AK9 / TEPBGA: K31)
100110 = GPIO38 (EBGA: AJ9 / TEPBGA: K28)
100111 = GPIO39 (EBGA: AL8 / TEPBGA: J31)
101000 = GPIO40 (EBGA: A21 / TEPBGA: Y3)
101001 = GPIO41 (EBGA: C19 / TEPBGA: W4)
101010 = GPIO42
101011 = GPIO43
101100 = GPIO44
101101 = GPIO45
101110 = GPIO46
101111 = GPIO47
110000 = GPIO48
110001 = GPIO49
110010 = GPIO50
110011 = GPIO51
110100 = GPIO52
110101 = GPIO53
110110 = GPIO54
110111 = GPIO55
111000 = GPIO56
111001 = GPIO57
111010 = GPIO58
111011 = GPIO59
111100 = GPIO60
111101 = GPIO61
111110 = GPIO62
111111 = GPIO63 (Note)
Note:
GPIO63 can be used to generate the PWRBTN# input signal. See PWRBTN# signal description in Section 3.4.15
"Power Management Interface Signals" on page 80.
Offset 24h-27h
GPIO Signal Configuration Access Register (R/W)
Reset Value: 00000044h
This register is used to indicate configuration for the GPIO signal that is selected in the GPIO Signal Configuration Select Register
(above).
Note:
31:7
6
PME debouncing, polarity, and edge/level configuration is only applicable on GPIO0-GPIO15 signals (Bank 0 = 00000 to
01111) and on GPIO32-GPIO47 signals (Bank 1 settings of 00000 to 01111). The remaining GPIOs (GPIO16-GPIO31 and
GPIO48-GPIO63) can not generate PMEs, therefore these bits have no function and read 0.
Reserved. Must be set to 0.
PME Debounce Enable. Enables/disables IRQ debounce (debounce period = 16 ms).
0: Disable.
1: Enable. (Default).
See the note in the description of this register for more information about the default value of this bit.
5
PME Polarity. Selects the polarity of the signal that issues a PME from the selected GPIO signal (falling/low or rising/high).
0: Falling edge or low level input. (Default)
1: Rising edge or high level input.
See the note in the description of this register for more information about the default value of this bit.
242
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Revision 5.1
Table 6-30. F0BAR0+I/O Offset: GPIO Configuration Registers (Continued)
Bit
4
Description
PME Edge/Level Select. Selects the type (edge or level) of the signal that issues a PME from the selected GPIO signal.
0: Edge input. (Default)
1: Level input.
For normal operation, always set this bit to 0 (edge input). Erratic system behavior results if this bit is set to 1.
See the note in the description of this register for more information about the default value of this bit.
3
Lock. This bit locks the selected GPIO signal. Once this bit is set to 1 by software, it can only be cleared to 0 by power on
reset or by WATCHDOG reset.
0: No effect. (Default)
1: Direction, output type, pull-up and output value locked.
2
Pull-Up Control. Enables/disables the internal pull-up capability of the selected GPIO signal. It supports open-drain output
signals with internal pull-ups and TTL input signals.
0: Disable.
1: Enable. (Default)
Bits [1:0] of this register must = 01 for this bit to have effect.
1
Output Type. Controls the output buffer type (open-drain or push-pull) of the selected GPIO signal.
0: Open-drain. (Default)
1: Push-pull.
Bit 0 of this register must be set to 1 for this bit to have effect.
0
Output Enable. Indicates the GPIO signal output state. It has no effect on input.
0: TRI-STATE - Setting for GPIO to function as an input only. (Default)
1: Output enabled.
Offset 28h-2Bh
31:1
0
GPIO Reset Control Register (R/W)
Reset Value: 00000000h
Reserved. Must be set to 0.
GPIO Reset. Reset the GPIO logic.
0: Disable.
1: Enable.
Write 0 to clear.
This bit is level-sensitive and must be cleared after the reset is enabled (normal operation requires this bit to be 0).
AMD Geode™ SC3200 Processor Data Book
243
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
6.4.1.2 LPC Support Registers
F0 Index 14h, Base Address Register 1 (F0BAR1) points to
the base address of the register space that contains the
configuration registers for LPC support. Table 6-31 gives
the bit formats of the I/O mapped registers accessed
through F0BAR1.
The LPC Interface supports all features described in the
LPC bus specification 1.0, with the following exceptions:
• Only 8- or 16-bit DMA, depending on channel number.
Does not support the optional larger transfer sizes.
• Only one external DRQ pin.
Table 6-31. F0BAR1+I/O Offset: LPC Interface Configuration Registers
Bit
Description
Offset 00h-03h
Note:
31:21
20
SERIRQ_SRC — Serial IRQ Source Register (R/W)
Reset Value: 00000000h
Some signals require additional programming to make them externally accessible. See Table 4-2 "Multiplexing, Interrupt Selection, and Base Address Registers" on page 88 for pin multiplexing details and Table 3-6 "Strap Options" on page 58 for
LPC_ROM strap information.
Reserved.
INTD Source. Selects the interface source of the INTD# signal.
0: PCI - INTD# (EBGA ball B22; TEPBGA ball AA2).
1: LPC - SERIRQ (EBGA ball AL8; TEPBGA ball J31).
19
INTC Source. Selects the interface source of the INTC# signal.
0: PCI - INTC# (EBGA ball H4; TEPBGA ball C9).
1: LPC - SERIRQ (EBGA ball AL8; TEPBGA ball J31).
18
INTB Source. Selects the interface source of the INTB# signal.
0: PCI - INTB# (EBGA ball AF1; TEPBGA ball C26).
1: LPC - SERIRQ (EBGA ball AL8; TEPBGA ball J31).
17
INTA Source. Selects the interface source of the INTA# signal.
0: PCI - INTA# (EBGA ball AE3; TEPBGA ball D26).
1: LPC - SERIRQ (EBGA ball AL8; TEPBGA ball J31).
16
Reserved. Set to 0.
15
IRQ15 Source. Selects the interface source of the IRQ15 signal.
0: ISA - IRQ15 (EBGA ball H30; TEPBGA ball AJ8).
1: LPC - SERIRQ (EBGA ball AL8; TEPBGA ball J31).
14
IRQ14 Source. Selects the interface source of the IRQ14 signal.
0: ISA - IRQ14 (EBGA ball D25; TEPBGA ball AF1).
1: LPC - SERIRQ (EBGA ball AL8; TEPBGA ball J31).
13
IRQ13 Source. Selects the interface source of the internal IRQ13 signal.
0: ISA - IRQ13 internal signal. (An input from the CPU indicating that a floating point error has been detected and that internal INTR should be asserted.)
1: LPC - SERIRQ (EBGA ball AL8; TEPBGA ball J31).
12
IRQ12 Source. Selects the interface source of the IRQ12 signal.
0: ISA - IRQ12 (unavailable externally).
1: LPC - SERIRQ (EBGA ball AL8; TEPBGA ball J31).
11
IRQ11 Source. Selects the interface source of the IRQ11 signal.
0: ISA - IRQ11 (unavailable externally).
1: LPC - SERIRQ (EBGA ball AL8; TEPBGA ball J31).
10
IRQ10 Source. Selects the interface source of the IRQ10 signal.
0: ISA - IRQ10 (unavailable externally).
1: LPC - SERIRQ (EBGA ball AL8; TEPBGA ball J31).
9
IRQ9 Source. Selects the interface source of the IRQ9 signal.
0: ISA - IRQ9 (EBGA ball C22; TEPBGA ball AA3).
1: LPC - SERIRQ (EBGA ball AL8; TEPBGA ball J31).
244
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Revision 5.1
Table 6-31. F0BAR1+I/O Offset: LPC Interface Configuration Registers (Continued)
Bit
8
Description
IRQ8# Source. Selects the interface source of the IRQ8# signal.
0: ISA - IRQ8# internal signal. (Connected to internal RTC.)
1: LPC - SERIRQ (EBGA ball AL8; TEPBGA ball J31).
7
IRQ7 Source. Selects the interface source of the IRQ7 signal.
0: ISA - IRQ7 (unavailable externally).
1: LPC - SERIRQ (EBGA ball AL8; TEPBGA ball J31).
6
IRQ6 Source. Selects the interface source of the IRQ6 signal.
0: ISA - IRQ6 (unavailable externally).
1: LPC - SERIRQ (EBGA ball AL8; TEPBGA ball J31).
5
IRQ5 Source. Selects the interface source of the IRQ5 signal.
0: ISA - IRQ5 (unavailable externally).
1: LPC - SERIRQ (EBGA ball AL8; TEPBGA ball J31).
4
IRQ4 Source. Selects the interface source of the IRQ4 signal.
0: ISA - IRQ4 (unavailable externally).
1: LPC - SERIRQ (EBGA ball AL8; TEPBGA ball J31).
3
IRQ3 Source. Selects the interface source of the IRQ3 signal.
0: ISA - IRQ3 (unavailable externally).
1: LPC - SERIRQ (EBGA ball AL8; TEPBGA ball J31).
2
Reserved. Must be set to 0.
1
IRQ1 Source. Selects the interface source of the IRQ1 signal.
0: ISA - IRQ1 (unavailable externally).
1: LPC - SERIRQ (EBGA ball AL8; TEPBGA ball J31).
0
IRQ0 Source. Selects the interface source of the IRQ0 signal.
0: ISA - IRQ0 Internal signal. (Connected to OUT0, System Timer, of the internal 8254 PIT.)
1: LPC - SERIRQ (EBGA ball AL8; TEPBGA ball J31).
Offset 04h-07h
31:21
20
SERIRQ_LVL — Serial IRQ Level Control Register (R/W)
Reset Value: 00000000h
Reserved.
INTD# Polarity. If LPC is selected as the interface source for INTD# (F0BAR1+I/O Offset 00h[20] = 1), this bit allows signal
polarity selection.
0: Active high.
1: Active low.
19
INTC# Polarity. If LPC is selected as the interface source for INTC# (F0BAR1+I/O Offset 00h[19] = 1), this bit allows signal
polarity selection.
0: Active high.
1: Active low.
18
INTB# Polarity. If LPC is selected as the interface source for INTB# (F0BAR1+I/O Offset 00h[18] = 1), this bit allows signal
polarity selection.
0:
1:
17
Active high.
Active low.
INTA# Polarity. If LPC is selected as the interface source for INTA# (F0BAR1+I/O Offset 00h[17] = 1), this bit allows signal
polarity selection.
0: Active high.
1: Active low.
16
Reserved. Must be set to 0.
15
IRQ15 Polarity. If LPC is selected as the interface source for IRQ15 (F0BAR1+I/O Offset 00h[15] = 1), this bit allows signal
polarity selection.
0: Active high.
1: Active low.
AMD Geode™ SC3200 Processor Data Book
245
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Table 6-31. F0BAR1+I/O Offset: LPC Interface Configuration Registers (Continued)
Bit
Description
14
IRQ14 Polarity. If LPC is selected as the interface source for IRQ14 (F0BAR1+I/O Offset 00h[14] = 1), this bit allows signal
polarity selection.
0: Active high.
1: Active low.
13
IRQ13 Polarity. If LPC is selected as the interface source for IRQ13 (F0BAR1+I/O Offset 00h[13] = 1), this bit allows signal
polarity selection.
0: Active high.
1: Active low.
12
IRQ12 Polarity. If LPC is selected as the interface source for IRQ12 (F0BAR1+I/O Offset 00h[12] = 1), this bit allows signal
polarity selection.
0: Active high.
1: Active low.
11
IRQ11 Polarity. If LPC is selected as the interface source for IRQ11 (F0BAR1+I/O Offset 00h[11] = 1), this bit allows signal
polarity selection.
0: Active high.
1: Active low.
10
IRQ10 Polarity. If LPC is selected as the interface source for IRQ10 (F0BAR1+I/O Offset 00h[10] = 1), this bit allows signal
polarity selection.
0: Active high.
1: Active low.
9
IRQ9 Polarity. If LPC is selected as the interface source for IRQ9 (F0BAR1+I/O Offset 00h[9] = 1), this bit allows signal
polarity selection.
0: Active high.
1: Active low.
8
IRQ8# Polarity. If LPC is selected as the interface source for IRQ8# (F0BAR1+I/O Offset 00h[8] = 1), this bit allows signal
polarity selection.
0: Active high.
1: Active low.
7
IRQ7 Polarity. If LPC is selected as the interface source for IRQ7 (F0BAR1+I/O Offset 00h[7] = 1), this bit allows signal
polarity selection.
0: Active high.
1: Active low.
6
IRQ6 Polarity. If LPC is selected as the interface source for IRQ6 (F0BAR1+I/O Offset 00h[6] = 1), this bit allows signal
polarity selection.
0: Active high.
1: Active low.
5
IRQ5 Polarity. If LPC is selected as the interface source for IRQ5 (F0BAR1+I/O Offset 00h[5] = 1), this bit allows signal
polarity selection.
0: Active high.
1: Active low.
4
IRQ4 Polarity. If LPC is selected as the interface source for IRQ4 (F0BAR1+I/O Offset 00h[4] = 1), this bit allows signal
polarity selection.
0: Active high.
1: Active low.
3
IRQ3 Polarity. If LPC is selected as the interface source for IRQ3 (F0BAR1+I/O Offset 00h[3] = 1), this bit allows signal
polarity selection.
0: Active high.
1: Active low.
246
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Table 6-31. F0BAR1+I/O Offset: LPC Interface Configuration Registers (Continued)
Bit
2
Description
SMI# Polarity. This bit allows signal polarity selection of the SMI# generated from LPC.
0: Active high.
1: Active low.
1
IRQ1 Polarity. If LPC is selected as the interface source for IRQ1 (F0BAR1+I/O Offset 00h[1] = 1), this bit allows signal
polarity selection.
0: Active high.
1: Active low.
0
IRQ0 Polarity. If LPC is selected as the interface source for IRQ0 (F0BAR1+I/O Offset 00h[0] = 1), this bit allows signal
polarity selection.
0: Active high.
1: Active low.
Offset 08h-0Bh
31:8
7
SERIRQ_CNT — Serial IRQ Control Register (R/W)
Reset Value: 00000000h
Reserved.
Serial IRQ Enable.
0: Disable.
1: Enable.
6
Serial IRQ Interface Mode.
0: Continuous.
1: Quiet.
5:2
Number of IRQ Data Frames.
0000: 17 frames
0001: 18 frames
0010: 19 frames
0011: 20 frames
1:0
0100: 21 frames
0101: 22 frames
0110: 23 frames
0111: 24 frames
1000: 25 frames
1001: 26 frames
1010: 27 frames
1011: 28 frames
1100: 29 frames
1101: 30 frames
1110: 31 frames
1111: 32 frames
Start Frame Pulse Width.
00: 4 Clocks
01: 6 Clocks
10: 8 Clocks
11: Reserved
Offset 0Ch-0Fh
Note:
31:8
7
DRQ_SRC — DRQ Source Register (R/W)
Reset Value: 00000000h
DRQx are internal signals between the Core Logic and SuperI/O modules. Some signals require additional programming to
make them externally accessible. See Table 4-2 "Multiplexing, Interrupt Selection, and Base Address Registers" on page 88 for
pin multiplexing details and Table 3-6 "Strap Options" on page 58 for LPC_ROM strap information.
Reserved.
DRQ7 Source. Selects the interface source of the DRQ7 signal.
0: ISA - DRQ7 (unavailable externally).
1: LPC - LDRQ# (EBGA ball AL9; TEPBGA ball L28).
6
DRQ6 Source. Selects the interface source of the DRQ6 signal.
0: ISA - DRQ6 (unavailable externally).
1: LPC - LDRQ# (EBGA ball AL9; TEPBGA ball L28).
5
DRQ5 Source. Selects the interface source of the DRQ5 signal.
0: ISA - DRQ5 (unavailable externally).
1: LPC - LDRQ# (EBGA ball AL9; TEPBGA ball L28).
4
LPC BM0 Cycles. Allow LPC Bus Master 0 Cycles.
0: Enable.
1: Disable.
3
DRQ3 Source. Selects the interface source of the DRQ3 signal.
0: ISA - DRQ3 (unavailable externally).
1: LPC - LDRQ# (EBGA ball AL9; TEPBGA ball L28).
AMD Geode™ SC3200 Processor Data Book
247
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Table 6-31. F0BAR1+I/O Offset: LPC Interface Configuration Registers (Continued)
Bit
2
Description
DRQ2 Source. Selects the interface source of the DRQ2 signal.
0: ISA - DRQ2 (unavailable externally).
1: LPC - LDRQ# (EBGA ball AL9; TEPBGA ball L28).
1
DRQ1 Source. Selects the interface source of the DRQ1 signal.
0: ISA - DRQ1 (unavailable externally).
1: LPC - LDRQ# (EBGA ball AL9; TEPBGA ball L28).
0
DRQ0 Source. Selects the interface source of the DRQ0 signal.
0: ISA - DRQ0 (unavailable externally).
1: LPC - LDRQ# (EBGA ball AL9; TEPBGA ball L28).
Offset 10h-13h
31:18
LAD_EN — LPC Address Enable Register (R/W)
Reset Value: 00000000h
Reserved.
17
LPC RTC. RTC addresses I/O Ports 070h-073h. See bit 16 for decode.
16
LPC/ISA Default Mapping. Works in conjunction with bits 17 and [14:0] of this register to enable mapping of specific
peripherals to LPC or internal ISA interfaces.
If bit [x] = 0 and bit 16 = 0 then: Transaction routed to internal ISA bus.
If bit [x] = 0 and bit 16 = 1 then: Transaction routed to LPC interface.
If bit [x] = 1 and bit 16 = 0 then: Transaction routed to LPC interface.
If bit [x] = 1 and bit 16 = 1 then: Transaction routed to internal ISA bus.
Bit [x] is defined as bits 17 and [14:0].
15
LPC ROM Addressing. Depends upon F0 Index 52h[2,0].
0: Disable.
1: Enable.
14
LPC Alternate SuperI/O Addressing. Alternate SuperI/O control addresses 4Eh-4Fh. See bit 16 for decode.
13
LPC SuperI/O Addressing. SuperI/O control addresses I/O Ports 2Eh-2Fh. See bit 16 for decode.
Note:
12
This bit should not be routed to LPC when using the internal SuperI/O module and if IO_SIOCFG_IN (F5BAR0+I/O
Offset 00h[26:25]) = 10.
LPC Ad-Lib Addressing. Ad-Lib addresses I/O Ports 388h-389h. See bit 16 for decode.
11
LPC ACPI Addressing. ACPI microcontroller addresses I/O Ports 62h and 66h. See bit 16 for decode.
10
LPC Keyboard Controller Addressing. KBC addresses I/O Ports 60h and 64h.
Note:
9
If this bit = 0 and bit 16 = 1, then F0 Index 5Ah[1] must be written 0.
LPC Wide Generic Addressing. Wide generic addresses. See bit 16 for decode.
Address selection made via F0BAR1+I/O Offset 18h[15:9]
Note:
8
The selected range must not overlap any address range that is positively decoded by F0BAR1+I/O Offset 10h bits
[17], [14:10], and [8:0].
LPC Game Port 1 Addressing. Game Port 1 addresses. See bit 16 for decode.
Address selection made via F0BAR1+I/O Offset 14h[22:19]
7
LPC Game Port 0 Addressing. Game Port 0 addresses. See bit 16 for decode.
Address selection made via F0BAR1+I/O Offset 14h[18:15].
6
LPC Floppy Disk Controller Addressing. FDC addresses. See bit 16 for decode.
Address selection made via F0BAR1+I/O Offset 14h[14]
5
LPC Microsoft Sound System (MSS) Addressing. MSS addresses. See bit 16 for decode.
Address selection made via F0BAR1+I/O Offset 14h[13:12].
4
LPC MIDI Addressing. MIDI addresses. See bit 16 for decode.
Address selection made via F0BAR1+I/O Offset 14h[11:10].
3
LPC Audio Addressing. Audio addresses. See bit 16 for decode.
Address selection made via F0BAR1+I/O Offset 14h[9:8].
2
LPC Serial Port 1 Addressing. Serial Port 1 addresses. See bit 16 for decode.
Address selection made via F0BAR1+I/O Offset 14h[7:5].
248
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Table 6-31. F0BAR1+I/O Offset: LPC Interface Configuration Registers (Continued)
Bit
1
Description
LPC Serial Port 0 Addressing. Serial Port 0 addresses. See bit 16 for decode.
Address selection made via F0BAR1+I/O Offset 14h[4:2].
0
LPC Parallel Port Addressing. Parallel Port addresses. See bit 16 for decode.
Address selection made via F0BAR1+I/O Offset 14h[1:0].
Offset 14h-17h
LAD_D0 — LPC Address Decode 0 Register (R/W)
31:23
Reserved.
22:19
LPC Game Port 1 Address Select. Selects I/O Port:
0000: 200h
0001: 201h
0010: 202h
0011: 203h
0100: 204h
0101: 205h
0110: 206h
0111: 207h
1000: 208h
1001: 209h
1010: 20Ah
1011: 20Bh
Reset Value: 00080020h
1100: 20Ch
1101: 20Dh
1110: 20Eh
1111: 20Fh
Selected address range is enabled via F0BAR1+I/O Offset 10h[8].
18:15
LPC Game Port 0 Address Select. Selects I/O Port:
0000: 200h
0001: 201h
0010: 202h
0011: 203h
0100: 204h
0101: 205h
0110: 206h
0111: 207h
1000: 208h
1001: 209h
1010: 20Ah
1011: 20Bh
1100: 20Ch
1101: 20Dh
1110: 20Eh
1111: 20Fh
Selected address range is enabled via F0BAR1+I/O Offset 10h[7].
14
LPC Floppy Disk Controller Address Select. Selects I/O Port:
0: 3F0h-3F7h.
1: 370h-377h.
Selected address range is enabled via F0BAR1+I/O Offset 10h[6].
13:12
LPC Microsoft Sound System (MSS) Address Select. Selects I/O Port:
00: 530h-537h
01: 604h-60Bh
10: E80h-E87h
11: F40h-F47h
Selected address range is enabled via F0BAR1+I/O Offset 10h[5].
11:10
LPC MIDI Address Select. Selects I/O Port:
00: 300h-301h
01: 310h-311h
10: 320h-321h
11: 330h-331h
Selected address range is enabled via F0BAR1+I/O Offset 10h[4].
9:8
LPC Audio Address Select. Selects I/O Port:
00: 220h-233h
01: 240h-253h
10: 260h-273h
11: 280h-293h
Selected address range is enabled via F0BAR1+I/O Offset 10h[3].
7:5
LPC Serial Port 1 Address Select. Selects I/O Port:
000: 3F8h-3FFh
001: 2F8h-2FFh
010: 220h-227h
011: 228h-22Fh
100: 238h-23Fh
101: 2E8h-2EFh
110: 338h-33Fh
111: 3E8h-3EFh
Selected address range is enabled via F0BAR1+I/O Offset 10h[2].
4:2
LPC Serial Port 0 Address Select. Selects I/O Port:
000: 3F8h-3FFh
001: 2F8h-2FFh
010: 220h-227h
011: 228h-22Fh
100: 238h-23Fh
101: 2E8h-2EFh
110: 338h-33Fh
111: 3E8h-3EFh
Selected address range is enabled via F0BAR1+I/O Offset 10h[1].
1:0
LPC Parallel Port Address Select. Selects I/O Port:
00: 378h-37Fh (+778h-77Fh for ECP)
10: 3BCh-3BFh (+7BCh-7BFh for ECP)
01: 278h-27Fh (+678h-67Fh for ECP) (Note)
11: Reserved
Selected address range is enabled via F0BAR1+I/O Offset 10h[0].
Note:
279h is read only, writes are forwarded to ISA for PnP.
AMD Geode™ SC3200 Processor Data Book
249
Revision 5.1
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Table 6-31. F0BAR1+I/O Offset: LPC Interface Configuration Registers (Continued)
Bit
Description
Offset 18h-1Bh
LAD_D1 — LPC Address Decode 1 Register (R/W)
Reset Value: 00000000h
31:16
Reserved. Must be set to 0.
15:9
Wide Generic Base Address Select. Defines a 512 byte space. Can be mapped anywhere in the 64 KB I/O space. AC97
and other configuration registers are expected to be mapped to this range. It is wide enough to allow many unforeseen
devices to be supported. Enabled at F0BAR1+I/O Offset 10h[9].
Note:
8:0
The selected range must not overlap any address range that is positively decoded by F0BAR1+I/O Offset 10h bits
[17], [14:10], and [8:0].
Reserved. Must be set to 0.
Offset 1Ch-1Fh
31:12
11
LPC_ERR_SMI — LPC Error SMI Register (R/W)
Reset Value: 00000080h
Reserved. Must be set to 0.
LPCPD# Override Enable. Determines how LPCPD# output is controlled.
0: ACPI logic.
1: LPCPD# Override Value bit (bit 10 of this register).
10
LPCPD# Override Value. Selects value of LPCPD# output if bit 11 of this register is set to 1.
0: Power down sequence.
1: Normal power.
9
SMI Serial IRQ Enable. Allows serial IRQ to generate an SMI.
0: Disable.
1: Enable.
Top Level SMI status is reported at F1BAR0+I/O Offset 02h[3].
Second level status is reported at bit 6 of this register.
8
SMI Configuration for LPC Error Enable. Allows LPC errors to generate an SMI.
0: Disable.
1: Enable.
Top Level SMI status is reported at F1BAR0+I/O Offset 02h[3].
Second level status is reported at bit 5 of this register.
7
LPCPD# Pin Status. (Read Only) Reflects the current value of the LPCPD# output signal.
6
SMI Source is Serial IRQ. Indicates whether or not an SMI was generated by an SERIRQ.
0: No.
1: Yes.
Write 1 to clear.
To enable SMI generation, set bit 9 of this register to 1.
This is the second level of status reporting. The top level status is reported in F1BAR0+I/O Offset 02h[3].
Writing a 1 to this bit also clears the top level status bit as long as bit 5 of this register is cleared.
5
LPC Error Status. Indicates whether or not an SMI was generated by an error that occurred on LPC.
0: No.
1: Yes.
Write 1 to clear.
To enable SMI generation, set bit 8 of this register to 1.
This is the second level of status reporting. The top level status is reported in F1BAR0+I/O Offset 02h[3].
Writing a 1 to this bit also clears the top level status bit as long as bit 6 of this register is cleared.
4
LPC Multiple Errors Status. Indicates whether or not multiple errors have occurred on LPC.
0: No.
1: Yes.
Write 1 to clear.
250
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
Revision 5.1
Table 6-31. F0BAR1+I/O Offset: LPC Interface Configuration Registers (Continued)
Bit
3
Description
LPC Timeout Error Status. Indicates whether or not an error was generated by a timeout on LPC.
0: No.
1: Yes.
Write 1 to clear.
2
LPC Error Write Status. Indicates whether or not an error was generated during a write operation on LPC.
0: No.
1: Yes.
Write 1 to clear.
1
LPC Error DMA Status. Indicates whether or not an error was generated during a DMA operation on LPC.
0: No.
1: Yes.
Write 1 to clear.
0
LPC Error Memory Status. Indicates whether or not an error was generated during a memory operation on LPC.
0: No.
1: Yes.
Write 1 to clear.
Offset 20h-23h
31:0
LPC_ERR_ADD — LPC Error Address Register (RO)
Reset Value: 00000000h
LPC Error Address.
AMD Geode™ SC3200 Processor Data Book
251
Revision 5.1
6.4.2
Core Logic Module - SMI Status and ACPI Registers - Function 1
SMI Status and ACPI Registers - Function 1
The register space designated as Function 1 (F1) is used
to configure the PCI portion of support hardware for the
SMI Status and ACPI Support registers. The bit formats for
the PCI Header registers are given in Table 6-32.
Located in the PCI Header registers of F1 are two Base
Address Registers (F1BARx) used for pointing to the register spaces designated for SMI status and ACPI support,
described later in this section.
Table 6-32. F1: PCI Header Registers for SMI Status and ACPI Support
Bit
Description
Index 00h-01h
Vendor Identification Register (RO)
Reset Value: 100Bh
Index 02h-03h
Device Identification Register (RO)
Reset Value: 0501h
Index 04h-05h
PCI Command Register (R/W)
Reset Value: 0000h
15:1
Reserved. (Read Only)
0
I/O Space. Allow the Core Logic module to respond to I/O cycles from the PCI bus.
0: Disable.
1: Enable.
This bit must be enabled to access I/O offsets through F1BAR0 and F1BAR1 (see F1 Index 10h and 40h).
Index 06h-07h
Index 08h
PCI Status Register (RO)
Reset Value: 0280h
Device Revision ID Register (RO)
Index 09h-0Bh
Reset Value: 00h
PCI Class Code Register (RO)
Reset Value: 068000h
Index 0Ch
PCI Cache Line Size Register (RO)
Reset Value: 00h
Index 0Dh
PCI Latency Timer Register (RO)
Reset Value: 00h
Index 0Eh
PCI Header Type (RO)
Reset Value: 00h
Index 0Fh
PCI BIST Register (RO)
Reset Value: 00h
Index 10h-13h
Base Address Register 0 - F1BAR0 (R/W)
Reset Value: 00000001h
This register allows access to I/O mapped SMI status related registers. Bits [7:0] are read only (0000 0001), indicating a 256-byte I/O
address range. Refer to Table 6-33 on page 253 for bit formats and reset values of the SMI status registers.
31:8
SMI Status Base Address.
7:0
Address Range. (Read Only)
Index 14h-2Bh
Reserved
Reset Value: 00h
Index 2Ch-2Dh
Subsystem Vendor ID (RO)
Reset Value: 100Bh
Index 2Eh-2Fh
Subsystem ID (RO)
Reset Value: 0501h
Index 30h-3Fh
Reserved
Index 40h-43h
Base Address Register 1 - F1BAR1 (R/W)
Reset Value: 00h
Reset Value: 00000001h
This register allows access to I/O mapped ACPI related registers. Bits [7:0] are read only (0000 0001), indicating a 256 byte address
range. Refer to Table 6-34 on page 263 for bit formats and reset values of the ACPI registers.
Note:
This Base Address register moved from its normal PCI Header Space (F1 Index 14h) to prevent plug and play software from
relocating it after an FACP table is built.
31:8
ACPI Base Address.
7:1
Address Range. (Read Only)
0
Enable. (Write Only) This bit must be set to 1 to enable access to ACPI Support Registers.
Index 44h-FFh
252
Reserved
Reset Value: 00h
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module - SMI Status and ACPI Registers - Function 1
6.4.2.1 SMI Status Support Registers
F1 Index 10h, Base Address Register 0 (F1BAR0), points
to the base address for SMI Status register locations.
Table 6-33 gives the bit formats of I/O mapped SMI Status
registers accessed through F1BAR0.
The registers at F1BAR0+I/O Offset 50h-FFh can also be
accessed F0 Index 50h-FFh. The preferred method is to
program these registers through the F0 register space.
Table 6-33. F1BAR0+I/O Offset: SMI Status Registers
Bit
Description
Offset 00h-01h
Note:
Top Level PME/SMI Status Mirror Register (RO)
Reset Value: 0000h
Reading this register does not clear the status bits. For more information, see F1BAR0+I/O Offset 02h.
15
Suspend Modulation Enable Mirror. This bit mirrors the Suspend Mode Configuration bit (F0 Index 96h[0]). It is used by
the SMI handler to determine if the SMI Speedup Disable Register (F1BAR0+I/O Offset 08h) must be cleared on exit.
14
SMI Source is USB. Indicates whether or not an SMI was caused by USB activity
0: No.
1: Yes.
To enable SMI generation, set F5BAR0+I/O Offset 00h[20:19] to 11.
13
SMI Source is Warm Reset Command. Indicates whether or not an SMI was caused by a Warm Reset command.
0: No.
1: Yes.
12
SMI Source is NMI. Indicates whether or not an SMI was caused by NMI activity.
0: No.
1: Yes.
11
SMI Source is IRQ2 of SIO Module. Indicates whether or not an SMI was caused by IRQ2 of the SIO module.
0: No.
1: Yes.
The next level (second level) of SMI status is reported in the SuperI/O module. For more information, see Table 5-29 "Banks
0 and 1 - Common Control and Status Registers" on page 134, Offset 00h.
10
SMI Source is EXT_SMI[7:0]. Indicates whether or not an SMI was caused by a negative-edge event on EXT_SMI[7:0].
0: No.
1: Yes.
The next level (second level) of SMI status is at F1BAR0+I/O Offset 24h[23:8].
9
SMI Source is GP Timers/UDEF/PCI/ISA Function Trap. Indicates if an SMI was caused by:
— Expiration of GP Timer 1 or 2.
— Trapped access to UDEF1, 2, or 3.
— Trapped access to F1-F5 or ISA Legacy register space.
0: No.
1: Yes.
The next level (second level) of SMI status is at F1BAR0+I/O Offset 04h/06h.
8
SMI Source is Software Generated. Indicates whether or not an SMI was caused by software.
0: No.
1: Yes.
7
SMI on an A20M# Toggle. Indicates whether or not an SMI was caused by a write access to either Port 92h or the keyboard command which initiates an A20M# SMI.
0: No.
1: Yes.
This method of controlling the internal A20M# in the GX1 module is used instead of a pin.
To enable SMI generation, set F0 Index 53h[0] to 1.
AMD Geode™ SC3200 Processor Data Book
253
Revision 5.1
Core Logic Module - SMI Status and ACPI Registers - Function 1
Table 6-33. F1BAR0+I/O Offset: SMI Status Registers (Continued)
Bit
6
Description
SMI Source is a VGA Timer Event. Indicates whether or not an SMI was caused by the expiration of the VGA Timer (F0
Index 8Eh).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 83h[3] to 1.
5
SMI Source is Video Retrace. Indicates whether or not an SMI was caused by a video retrace event as decoded from the
internal serial connection (PSERIAL register, bit 7) from the GX1 module.
0: No.
1: Yes.
To enable SMI generation, set F0 Index 83h[2] to 1.
4
Reserved. Reads as 0.
3
SMI Source is LPC. Indicates whether or not an SMI was caused by the LPC interface.
0: No.
1: Yes.
The next level (second level) of SMI status is at F0BAR1+I/O Offset 1Ch[6:5].
2
SMI Source is ACPI. Indicates whether or not an SMI was caused by an access (read or write) to one of the ACPI registers
(F1BAR1).
0: No.
1: Yes.
The next level (second level) of SMI status is at F1BAR0+I/O Offset 20h.
1
SMI Source is Audio Subsystem. Indicates whether or not an SMI was caused by the audio subsystem.
0: No.
1: Yes.
The next level (second level) of SMI status is at F3BAR0+Memory Offset 10h/12h.
0
SMI Source is Power Management Event. Indicates whether or not an SMI was caused by one of the power management
resources (except for GP timers, UDEFx and PCI/ISA function traps that are reported in bit 9).
0: No.
1: Yes.
The next level (second level) of SMI status is at F0 Index 84h-F4h/87h-F7h.
Offset 02h-03h
Note:
Top Level PME/SMI Status Register (RO/RC)
Reset Value: 0000h
Reading this register clears all the SMI status bits except for the “read only” bits, because they have a second level of status
reporting. Clearing the second level status bits also clears the top level (except for GPIOs).
GPIO SMIs have third level of SMI status reporting at F0BAR0+I/O Offset 0Ch/1Ch. Clearing the third level GPIO status bits
also clears the second and top levels.
A read-only “Mirror” version of this register exists at F1BAR0+I/O Offset 00h. If the value of the register must be read without
clearing the SMI source (and consequently de-asserting SMI), F1BAR0+I/O Offset 00h can be read instead.
15
Suspend Modulation Enable Mirror. (Read to Clear)
This bit mirrors the Suspend Mode Configuration bit (F0 Index 96h[0]). It is used by the SMI handler to determine if the SMI
Speedup Disable Register (F1BAR0+I/O Offset 08h) must be cleared on exit.
14
SMI Source is USB. (Read to Clear) Indicates whether or not an SMI was caused by USB activity.
0: No.
1: Yes.
To enable SMI generation, set F5BAR0+I/O Offset 00h[20:19] to 11.
13
SMI Source is Warm Reset Command. (Read to Clear) Indicates whether or not an SMI was caused by Warm Reset
command
0: No.
1: Yes.
254
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - SMI Status and ACPI Registers - Function 1
Revision 5.1
Table 6-33. F1BAR0+I/O Offset: SMI Status Registers (Continued)
Bit
Description
12
SMI Source is NMI. (Read to Clear) Indicates whether or not an SMI was caused by NMI activity.
0: No.
1: Yes.
11
SMI Source is IRQ2 of SIO Module. (Read to Clear) Indicates whether or not an SMI was caused by IRQ2 of the SIO
module.
0: No.
1: Yes.
The next level (second level) of SMI status is reported in the SuperI/O module. See Table 5-29 "Banks 0 and 1 - Common
Control and Status Registers" on page 134 for details.
10
SMI Source is EXT_SMI[7:0]. (Read Only. Read Does Not Clear) Indicates whether or not an SMI was caused by a negative-edge event on EXT_SMI[7:0].
0: No.
1: Yes.
The next level (second level) of SMI status is at F1BAR0+I/O Offset 24h[23:8].
9
SMI Source is General Timers/Traps. (Read Only, Read Does Not Clear) Indicates whether or not an SMI was caused
by the expiration of one of the General Purpose Timers or one of the User Defined Traps.
0: No.
1: Yes.
The next level (second level) of SMI status is at F1BAR0+I/O Offset 04h/06h.
8
SMI Source is Software Generated. (Read to Clear) Indicates whether or not an SMI was caused by software.
0: No.
1: Yes.
7
SMI on an A20M# Toggle. (Read to Clear) Indicates whether or not an SMI was caused by an access to either Port 92h or
the keyboard command which initiates an A20M# SMI
0: No.
1: Yes.
This method of controlling the internal A20M# in the GX1 module is used instead of a pin.
To enable SMI generation, set F0 Index 53h[0] to 1.
6
SMI Source is a VGA Timer Event. (Read to Clear) Indicates whether or not an SMI was caused by expiration of the VGA
Timer (F0 Index 8Eh).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 83h[3] to 1.
5
SMI Source is Video Retrace. (Read to Clear) Indicates whether or not an SMI was caused by a video retrace event as
decoded from the internal serial connection (PSERIAL register, bit 7) from the GX1 module.
0: No.
1: Yes.
To enable SMI generation, set F0 Index 83h[2] to 1.
4
Reserved. Reads as 0.
3
SMI Source is LPC. (Read Only, Read Does Not Clear) Indicates whether or not an SMI was caused by the LPC interface.
0: No.
1: Yes.
The next level (second level) of SMI status is at F0BAR1+I/O Offset 1Ch[6:5].
2
SMI Source is ACPI. (Read Only, Read Does Not Clear) Indicates whether or not an SMI was caused by an access (read
or write) to one of the ACPI registers (F1BAR1).
0: No.
1: Yes.
The next level (second level) of SMI status is at F1BAR0+I/O Offset 20h.
AMD Geode™ SC3200 Processor Data Book
255
Revision 5.1
Core Logic Module - SMI Status and ACPI Registers - Function 1
Table 6-33. F1BAR0+I/O Offset: SMI Status Registers (Continued)
Bit
1
Description
SMI Source is Audio Subsystem. (Read Only, Read Does Not Clear) Indicates whether or not an SMI was caused by the
audio subsystem.
0: No.
1: Yes.
The second level of status is found in F3BAR0+Memory Offset 10h/12h.
0
SMI Source is Power Management Event. (Read Only, Read Does Not Clear) Indicates whether or not an SMI was
caused by one of the power management resources (except for GP timers, UDEFx and PCI/ISA function traps which are
reported in bit 9).
0: No.
1: Yes.
The next level (second level) of SMI status is at F0 Index 84h/F4h-87h/F7h.
Offset 04h-05h
Second Level General Traps & Timers
PME/SMI Status Mirror Register (RO)
Reset Value: 0000h
The bits in this register contain second level status reporting. Top level status is reported at F1BAR0+I/O Offset 00h/02h[9].
Reading this register does not clear the SMI. For more information, see F1BAR0+I/O Offset 06h.
15:6
5
Reserved.
PCI/ISA Function Trap. Indicates whether or not an SMI was caused by a trapped PCI/ISA configuration cycle.
0: No.
1: Yes.
To enable SMI generation for:
— Trapped access to ISA Legacy I/O register space set F0 Index 41h[0] = 1.
— Trapped access to F1 register space set F0 Index 41h[1] = 1.
— Trapped access to F2 register space set F0 Index 41h[2] = 1.
— Trapped access to F3 register space set F0 Index 41h[3] = 1.
— Trapped access to F4 register space set F0 Index 41h[4] = 1.
— Trapped access to F5 register space set F0 Index 41h[5] = 1.
4
SMI Source is Trapped Access to User Defined Device 3. Indicates whether or not an SMI was caused by a trapped I/O
or memory access to the User Defined Device 3 (F0 Index C8h).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 82h[6] = 1.
3
SMI Source is Trapped Access to User Defined Device 2. Indicates whether or not an SMI was caused by a trapped I/O
or memory access to the User Defined Device 2 (F0 Index C4h).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 82h[5] = 1.
2
SMI Source is Trapped Access to User Defined Device 1. Indicates whether or not an SMI was caused by a trapped I/O
or memory access to the User Defined Device 1 (F0 Index C0h).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 82h[4] = 1.
1
SMI Source is Expired General Purpose Timer 2. Indicates whether or not an SMI was caused by the expiration of General Purpose Timer 2 (F0 Index 8Ah).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 83h[1] = 1.
256
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - SMI Status and ACPI Registers - Function 1
Revision 5.1
Table 6-33. F1BAR0+I/O Offset: SMI Status Registers (Continued)
Bit
0
Description
SMI Source is Expired General Purpose Timer 1. Indicates whether or not an SMI was caused by the expiration of General Purpose Timer 1 (F0 Index 88h).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 83h[0] = 1.
Offset 06h-07h
Second Level General Traps & Timers Status Register (RC)
Reset Value: 0000h
The bits in this register contain second level of status reporting. Top level status is reported in F1BAR0+I/O Offset 00h/02h[9]. Reading
this register clears the status at both the second and top levels.
A read-only “Mirror” version of this register exists at F1BAR0+I/O Offset 04h. If the value of this register must be read without clearing
the SMI source (and consequently de-asserting SMI), F1BAR0+I/O Offset 04h can be read instead.
15:6
5
Reserved.
PCI/ISA Function Trap. Indicates whether or not an SMI was caused by a trapped PCI/ISA configuration cycle
0: No.
1: Yes.
To enable SMI generation for:
— Trapped access to ISA Legacy I/O register space set F0 Index 41h[0] = 1.
— Trapped access to F1 register space set F0 Index 41h[1] = 1.
— Trapped access to F2 register space set F0 Index 41h[2] = 1.
— Trapped access to F3 register space set F0 Index 41h[3] = 1.
— Trapped access to F4 register space set F0 Index 41h[4] = 1.
— Trapped access to F5 register space set F0 Index 41h[5] = 1.
4
SMI Source is Trapped Access to User Defined Device 3 (UDEF3). Indicates whether or not an SMI was caused by a
trapped I/O or memory access to User Defined Device 3 (F0 Index C8h).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 82h[6] = 1.
3
SMI Source is Trapped Access to User Defined Device 2 (UDEF2). Indicates whether or not an SMI was caused by a
trapped I/O or memory access to User Defined Device 2 (F0 Index C4h).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 82h[5] = 1.
2
SMI Source is Trapped Access to User Defined Device 1 (UDEF1). Indicates whether or not an SMI was caused by a
trapped I/O or memory access to User Defined Device 1 (F0 Index C0h).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 82h[4] = 1.
1
SMI Source is Expired General Purpose Timer 2. Indicates whether or not an SMI was caused by the expiration of General Purpose Timer 2 (F0 Index 8Ah).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 83h[1] = 1.
0
SMI Source is Expired General Purpose Timer 1. Indicates whether or not an SMI was caused by the expiration of General Purpose Timer 1 (F0 Index 88h).
0: No.
1: Yes.
To enable SMI generation, set F0 Index 83h[0] = 1.
AMD Geode™ SC3200 Processor Data Book
257
Revision 5.1
Core Logic Module - SMI Status and ACPI Registers - Function 1
Table 6-33. F1BAR0+I/O Offset: SMI Status Registers (Continued)
Bit
Description
Offset 08h-09h
15:0
SMI Speedup Disable Register (Read to Enable)
Reset Value: 0000h
SMI Speedup Disable. If bit 1 in the Suspend Configuration Register is set (F0 Index 96h[1] = 1), a read of this register
invokes the SMI handler to re-enable Suspend Modulation.
The data read from this register can be ignored. If the Suspend Modulation feature is disabled, reading this I/O location has
no effect.
Offset 0Ah-1Bh
Reserved
Reset Value: 00h
These addresses should not be written.
Offset 1Ch-1Fh
Note:
ACPI Timer Register (RO)
Reset Value: xxxxxxxxh
This register can also be read at F1BAR1+I/O Offset 1Ch.
31:24
Reserved.
23:0
TMR_VAL. This field returns the running count of the power management timer.
Offset 20h-21h
Second Level ACPI PME/SMI
Status Mirror Register (RO)
Reset Value: 0000h
The bits in this register contain second level SMI status reporting. Top level status is reported in F1BAR0+I/O Offset 00h/02h[2].
Reading this register does not clear the SMI. For more information, see F1BAR0+I/O Offset 22h.
15:6
5
Reserved. Always reads 0.
ACPI BIOS SMI Status. Indicates whether or not an SMI was caused by ACPI software raising an event to BIOS software.
0: No.
1: Yes.
To enable SMI generation, set F1BAR1+I/O Offset 0Ch[2] to 1, and F1BAR1+I/O Offset 0Fh[0] to 1.
4
PLVL3 SMI Status. Indicates whether or not an SMI was caused by a read of the ACPI PLVL3 register (F1BAR1+I/O Offset
05h).
0: No.
1: Yes.
To enable SMI generation, set F1BAR1+I/O Offset 18h[11] to 1 (default).
3
Reserved.
2
SLP_EN SMI Status. Indicates whether or not an SMI was caused by a write of 1 to the ACPI SLP_EN bit (F1BAR1+I/O
Offset 0Ch[13]).
0: No.
1: Yes.
To enable SMI generation, set F1BAR1+I/O Offset 18h[9] to 1 (default).
1
THT_EN SMI Status. Indicates whether or not an SMI was caused by a write of 1 to the ACPI THT_EN bit (F1BAR1+I/O
Offset 00h[4]).
0: No.
1: Yes.
To enable SMI generation, set F1BAR1+I/O Offset 18h[8] to 1 (default).
0
SMI_CMD SMI Status. Indicates whether or not an SMI was caused by a write to the ACPI SMI_CMD register (F1BAR1+I/
O Offset 06h).
0: No.
1: Yes.
A write to the ACPI SMI_CMD register always generates an SMI.
258
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - SMI Status and ACPI Registers - Function 1
Revision 5.1
Table 6-33. F1BAR0+I/O Offset: SMI Status Registers (Continued)
Bit
Description
Offset 22h-23h
Second Level ACPI PME/SMI Status Register (RC)
Reset Value: 0000h
The bits in this register contain second level of SMI status reporting. Top level is reported in F1BAR0+I/O Offset 00h/02h[2].
Reading this register clears the status at both the second and top levels.
A read-only “Mirror” version of this register exists at F1BAR0+I/O Offset 20h. If the value of the register must be read without clearing the
SMI source (and consequently de-asserting SMI), F1BAR0+I/O Offset 20h can be read instead.
15:6
5
Reserved. Always reads 0.
ACPI BIOS SMI Status. Indicates whether or not an SMI was caused by ACPI software raising an event to BIOS software.
0: No.
1: Yes.
To enable SMI generation, set F1BAR1+I/O Offset 0Ch[2] to 1, and F1BAR1+I/O Offset 0Fh[0] to 1.
4
PLVL3 SMI Status. Indicates whether or not an SMI was caused by a read of the ACPI PLVL3 register (F1BAR1+I/O Offset
05h).
0: No.
1: Yes.
To enable SMI generation, set F1BAR1+I/O Offset 18h[11] to 1 (default).
3
Reserved.
2
SLP_EN SMI Status. Indicates whether or not an SMI was caused by a write of 1 to the ACPI SLP_EN bit (F1BAR1+I/O
Offset 0Ch[13]).
0: No.
1: Yes.
To enable SMI generation, set F1BAR1+I/O Offset 18h[9] to 1 (default).
1
THT_EN SMI Status. Indicates whether or not an SMI was caused by a write of 1 to the ACPI THT_EN bit (F1BAR1+I/O
Offset 00h[4])
0: No.
1: Yes.
To enable SMI generation, set F1BAR1+I/O Offset 18h[8] to 1 (default).
0
SMI_CMD SMI Status. Indicates whether or not an SMI was caused by a write to the ACPI SMI_CMD register (F1BAR1+I/
O Offset 06h).
0: No.
1: Yes.
A write to the ACPI SMI_CMD register always generates an SMI.
Offset 24h-27h
Note:
External SMI Register (R/W)
Reset Value: 00000000h
EXT_SMI[7:0] are external SMIs, meaning external to the Core Logic module.
Bits [23:8] of this register contain second level of SMI status reporting. Top level status is reported in F1BAR0+I/O Offset 00h/
02h[10]. Reading bits [23:16] clears the second and top levels. If the value of the status bits must be read without clearing the
SMI source (and consequently de-asserting SMI), bits [15:8] can be read instead.
31:24
23
Reserved. Must be set to 0.
EXT_SMI7 SMI Status. (Read to Clear) Indicates whether or not an SMI was caused by assertion of EXT_SMI7.
0: No.
1: Yes.
To enable SMI generation, set bit 7 to 1.
22
EXT_SMI6 SMI Status. (Read to Clear) Indicates whether or not an SMI was caused by an assertion of EXT_SMI6
0: No.
1: Yes.
To enable SMI generation, set bit 6 to 1.
AMD Geode™ SC3200 Processor Data Book
259
Revision 5.1
Core Logic Module - SMI Status and ACPI Registers - Function 1
Table 6-33. F1BAR0+I/O Offset: SMI Status Registers (Continued)
Bit
21
Description
EXT_SMI5 SMI Status. (Read to Clear) Indicates whether or not an SMI was caused by an assertion of EXT_SMI5.
0: No.
1: Yes.
To enable SMI generation, set bit 5 to 1.
20
EXT_SMI4 SMI Status. (Read to Clear) Indicates whether or not an SMI was caused by an assertion of EXT_SMI4.
0: No.
1: Yes.
To enable SMI generation, set bit 4 to 1.
19
EXT_SMI3 SMI Status. (Read to Clear) Indicates whether or not an SMI was caused by an assertion of EXT_SMI3.
0: No.
1: Yes.
To enable SMI generation, set bit 3 to 1.
18
EXT_SMI2 SMI Status. (Read to Clear) Indicates whether or not an SMI was caused by an assertion of EXT_SMI2.
0: No.
1: Yes.
To enable SMI generation, set bit 2 to 1.
17
EXT_SMI1 SMI Status. (Read to Clear) Indicates whether or not an SMI was caused by an assertion of EXT_SMI1.
0: No.
1: Yes.
To enable SMI generation, set bit 1 to 1.
16
EXT_SMI0 SMI Status. (Read to Clear) Indicates whether or not an SMI was caused by an assertion of EXT_SMI0.
0: No.
1: Yes.
To enable SMI generation, set bit 0 to 1.
15
EXT_SMI7 SMI Status. (Read Only) Indicates whether or not an SMI was caused by an assertion of EXT_SMI7.
0: No.
1: Yes.
To enable SMI generation, set bit 7 to 1.
14
EXT_SMI6 SMI Status. (Read Only) Indicates whether or not an SMI was caused by an assertion of EXT_SMI6.
0: No.
1: Yes.
To enable SMI generation, set bit 6 to 1.
13
EXT_SMI5 SMI Status. (Read Only) Indicates whether or not an SMI was caused by an assertion of EXT_SMI5.
0: No.
1: Yes.
To enable SMI generation, set bit 5 to 1.
12
EXT_SMI4 SMI Status. (Read Only) Indicates whether or not an SMI was caused by an assertion of EXT_SMI4.
0: No.
1: Yes.
To enable SMI generation, set bit 4 to 1.
11
EXT_SMI3 SMI Status. (Read Only) Indicates whether or not an SMI was caused by an assertion of EXT_SMI3.
0: No.
1: Yes.
To enable SMI generation, set bit 3 to 1.
260
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - SMI Status and ACPI Registers - Function 1
Revision 5.1
Table 6-33. F1BAR0+I/O Offset: SMI Status Registers (Continued)
Bit
Description
10
EXT_SMI2 SMI Status. (Read Only) Indicates whether or not an SMI was caused by an assertion of EXT_SMI2.
0: No.
1: Yes.
To enable SMI generation, set bit 2 to 1.
9
EXT_SMI1 SMI Status. (Read Only) Indicates whether or not an SMI was caused by an assertion of EXT_SMI1.
0: No.
1: Yes.
To enable SMI generation, set bit 1 to 1.
8
EXT_SMI0 SMI Status. (Read Only) Indicates whether or not an SMI was caused by an assertion of EXT_SMI0.
0: No.
1: Yes.
To enable SMI generation, set bit 0 to 1.
7
EXT_SMI7 SMI Enable. When this bit is asserted, allow EXT_SMI7 to generate an SMI on negative-edge events.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+00h/02h[10].
Second level SMI status is reported at bits 23 (RC) and 15 (RO).
6
EXT_SMI6 SMI Enable. When this bit is asserted, allow EXT_SMI6 to generate an SMI on negative-edge events.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+00h/02h[10].
Second level SMI status is reported at bits 22 (RC) and 14 (RO).
5
EXT_SMI5 SMI Enable. When this bit is asserted, allow EXT_SMI5 to generate an SMI on negative-edge events.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+00h/02h[10].
Second level SMI status is reported at bits 21 (RC) and 13 (RO).
4
EXT_SMI4 SMI Enable. When this bit is asserted, allows EXT_SMI4 to generate an SMI on negative-edge events.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+00h/02h[10].
Second level SMI status is reported at bits 20 (RC) and 12 (RO).
3
EXT_SMI3 SMI Enable. When this bit is asserted, allow EXT_SMI3 to generate an SMI on negative-edge events.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+00h/02h[10].
Second level SMI status is reported at bits 19 (RC) and 11 (RO).
2
EXT_SMI2 SMI Enable. When this bit is asserted, allow EXT_SMI2 to generate an SMI on negative-edge events.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+00h/02h[10].
Second level SMI status is reported at bits 18 (RC) and 10 (RO).
1
EXT_SMI1 SMI Enable. When this bit is asserted, allow EXT_SMI1 to generate an SMI on negative-edge events.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+00h/02h[10].
Second level SMI status is reported at bits 17 (RC) and 9 (RO).
AMD Geode™ SC3200 Processor Data Book
261
Revision 5.1
Core Logic Module - SMI Status and ACPI Registers - Function 1
Table 6-33. F1BAR0+I/O Offset: SMI Status Registers (Continued)
Bit
0
Description
EXT_SMI0 SMI Enable. When this bit is asserted, allow EXT_SMI0 to generate an SMI on negative-edge events.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+00h/02h[10].
Second level SMI status is reported at bits 16 (RC) and 8 (RO).
Offset 28h-4Fh
Offset
50h-FFh
262
Not Used
Reset Value: 00h
The I/O mapped registers located here (F1BAR0+I/O Offset 50h-FFh) can also be accessed at F0 Index 50h-FFh. The preferred method is to program these registers through the F0 register space. Refer to Table 6-29 "F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support" on page 206 for more information about these registers.
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module - SMI Status and ACPI Registers - Function 1
6.4.2.2 ACPI Support Registers
F1 Index 40h, Base Address Register 1 (F1BAR1), points
to the base address of where the ACPI Support registers
are located. Table 6-34 shows the I/O mapped ACPI Support registers accessed through F1BAR1.
Table 6-34. F1BAR1+I/O Offset: ACPI Support Registers
Bit
Description
Offset 00h-03h
31:5
P_CNT — Processor Control Register (R/W)
Reset Value: 00000000h
Reserved. Always reads 0.
4
THT_EN (Throttle Enable). When this bit is asserted, it enables throttling of the clock based on the CLK_VAL field (bits
[2:0] of this register).
0:
Disable.
1:
Enable.
If F1BAR1+I/O Offset 18h[8] =1, an SMI is generated when this bit is set.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[2].
Second level SMI status is reported at F1BAR0+I/O Offset 20h/22h[1].
3
Reserved. Always reads 0.
2:0
CLK_VAL (Clock Throttling Value). CPU duty cycle:
000: Reserved
001: 12.5%
010: 25%
011: 37.5%
Offset 04h
Note:
100: 50%
101: 62.5%
110: 75%
111: 87.5%
Reserved
Reset Value: 00h
This register should not be read. It controls a reserved function of power management logic.
Offset 05h
7:0
P_LVL3 — Enter C3 Power State Register (RO)
Reset Value: xxh
P_LVL3 (Power Level 3). Reading this 8-bit read only register causes the processor to enter the C3 power state. Reads of
P_LVL3 return 0. Writes have no effect.
The ACPI state machine always waits for an SMI (any SMI) to be generated and serviced before transfer into C3 power
state.
A read of this register causes an SMI if enabled: F1BAR1+I/O Offset 18h[11] = 1 (default).
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[2].
Second level SMI status is reported at F1BAR0+I/O Offset 20h/22h[4].
Offset 06h
7:0
SMI_CMD — OS/BIOS Requests Register (R/W)
Reset Value: 00h
SMI_CMD (SMI Command and OS / BIOS Requests). A write to this register stores data and a read returns the last data
written. In addition, a write to this register always generates an SMI. A read of this register does not generate an SMI.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[2].
Second level SMI status is reported at F1BAR0+I/O Offset 20h/22h[0].
Offset 07h
7:6
ACPI_FUN_CNT — ACPI Function Control Register (R/W)
Reset Value: 00h
LED_CNT (LED Output Control). Controls the blinking of an LED when in the SL4 or SL5 sleep state
00: Disable (LED# signal, is HiZ).
01: Zero (LED# signal is HiZ).
10: Blink @ 1 Hz rate, when in SL4 and SL5 sleep states. Duty cycle: LED# is 10% pulled low, 90% HiZ.
11: One (LED# is pulled low, when in SL4 and SL5 sleep states)
5
4
Reserved. Must be set to 0.
INTR_WU_SL1. Enables wakeup on enabled interrupts in sleep state SL1.
0: Disable wakeup from SL1, when an enabled interrupt is active.
1: Enable wakeup from SL1, when an enabled interrupt is active.
3
GPWIO_DBNC_DIS (GPWIO0 and GPWIO1 Debounce). When enabled, a high-to-low or low-to-high transition of greater
than 15.8 ms is required for GPWIO0 and GPWIO1 to be recognized.
0: Enable. (Default)
1: Disable. (No debounce)
GPWIO2 pin does not have debounce capability.
2:1
Reserved. Must be set to 0.
AMD Geode™ SC3200 Processor Data Book
263
Revision 5.1
Core Logic Module - SMI Status and ACPI Registers - Function 1
Table 6-34. F1BAR1+I/O Offset: ACPI Support Registers (Continued)
Bit
0
Description
PWRBTN_DBNC_DIS (Power Button Debounce). When enabled, a high-to-low or low-to-high transition of greater than
15.8 ms is required on PWRBTN# before it is recognized.
0: Enable. (Default)
1: Disable. (No debounce)
Offset 08h-09h
PM1A_STS — PM1A Top Level PME/SCI Status Register (R/W)
Reset Value: 0000h
Notes: 1. This is the top level of PME/SCI status reporting for these events. There is no second level.
2. If SCI generation is not desired, the status bits are still set by the described conditions and can be used for monitoring purposes.
15
WAK_STS (Wakeup Status). Indicates whether or not an SCI was caused by the occurrence of an enabled wakeup event.
0: No.
1: Yes.
This bit is set when the system is in any Sleep state and an enabled wakeup event occurs (wakeup events are configured at
F1BAR1+I/O Offset 0Ah and 12h). After this bit is set, the system transitions to a Working state.
SCI generation is always enabled.
Write 1 to clear.
14:12
11
Reserved. Must be set to 0.
PWRBTNOR_STS (Power Button Override Status). Indicates whether or not an SCI was caused by the power button
being active for greater than 4 seconds.
0: No.
1: Yes.
SCI generation is always enabled.
Write 1 to clear.
10
RTC_STS (Real-Time Clock Status). Indicates if a Power Management Event (PME) was caused by the RTC generating
an alarm (RTC IRQ signal is asserted).
0: No.
1: Yes.
For the PME to generate an SCI, set F1BAR1+I/O Offset 0Ah[10] to 1 and F1BAR1+I/O Offset 0Ch[0] to 1. (See Note 2 in
the general description of this register.)
Write 1 to clear.
9
Reserved. Must be set to 0.
8
PWRBTN_STS (Power Button Status). Indicates if PME was caused by the PWRBTN# going low while the system is in a
Working state.
0: No.
1: Yes.
For the PME to generate an SCI, set F1BAR1+I/O Offset 0Ah[8] = 1 and F1BAR1+I/O Offset 0Ch[0] = 1. (See Note 2 in the
general description of this register.)
In a Sleep state or the Soft-Off state, a wakeup event is generated when the power button is pressed (regardless of the
PWRBTN_EN bit, F1BAR1+I/O Offset 0Ah[8], setting).
Write 1 to clear.
7:6
5
Reserved. Must be set to 0.
GBL_STS (Global Lock Status). Indicates if PME was caused by the BIOS releasing control of the global lock.
0: No.
1: Yes.
This bit is used by the BIOS to generate an SCI. BIOS writes the BIOS_RLS bit (F1BAR1+I/O Offset 0Fh[1]) which in turns
sets the GBL_STS bit and raises a PME.
For the PME to generate an SCI, set F1BAR1+I/O Offset 0Ah[5] to 1 and F1BAR1+I/O Offset 0Ch[0] to 1. (See Note 2 in the
general description of this register.)
Write 1 to clear.
264
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - SMI Status and ACPI Registers - Function 1
Revision 5.1
Table 6-34. F1BAR1+I/O Offset: ACPI Support Registers (Continued)
Bit
4
Description
BM_STS (Bus Master Status). Indicates if PME was caused by a system bus master requesting the system bus.
0: No.
1: Yes.
For the PME to generate an SCI, set F1BAR1+I/O Offset 0Ch[1] = 1 and F1BAR1+I/O Offset 0Ch[0] = 1. (See Note 2 in the
general description of this register.)
Write 1 to clear.
3:1
0
Reserved. Must be set to 0.
TMR_STS (Timer Carry Status). Indicates if SCI was caused by an MSB toggle (MSB changes from low-to-high or high-tolow) on the ACPI Timer (F1BAR0+I/O Offset 1Ch or F1BAR1+I/O Offset 1Ch).
0: No.
1: Yes.
For the PME to generate an SCI, set F1BAR1+I/O Offset 0Ah[0] = 1 and F1BAR1+I/O Offset 0Ch[0] = 1. (See Note 2 in the
general description of this register.)
Write 1 to clear.
Offset 0Ah-0Bh
PM1A_EN — PM1A PME/SCI Enable Register (R/W)
Reset Value: 0000h
In order for the ACPI events described below to generate an SCI, the SCI_EN bit must also be set (F1BAR1+I/O Offset 0Ch[0] = 1).
The SCIs enabled via this register are globally enabled by setting F1BAR1+I/O Offset 08h. There is no second level of SCI status reporting for these bits.
15:11
10
Reserved. Must be set to 0.
RTC_EN (Real-Time Clock Enable). Allow SCI generation when the RTC generates an alarm (RTC IRQ signal is
asserted).
0: Disable.
1: Enable
9
Reserved. Must be set to 0.
8
PWRBTN_EN (Power Button Enable). Allow SCI generation when PWRBTN# goes low while the system is in a Working
state.
0: Disable.
1: Enable
7:6
5
Reserved. Must be set to 0.
GBL_EN (Global Lock Enable). Allow SCI generation when the BIOS releases control of the global lock via the BIOS_RLS
(F1BAR1+I/O Offset 0Fh[1] and GBL_STS (F1BAR1+I/O Offset 08h[5]) bits.
0: Disable.
1: Enable
4:1
0
Reserved. Must be set to 0.
TMR_EN (ACPI Timer Enable). Allow SCI generation for MSB toggles (MSB changes from low-to-high or high-to-low) on
the ACPI Timer (F1BAR0+I/O Offset 1Ch or F1BAR1+I/O Offset 1Ch).
0:
1:
Disable.
Enable
Offset 0Ch-0Dh
15:14
PM1A_CNT — PM1A Control Register (R/W)
Reset Value: 0000h
Reserved. Must be set to 0.
AMD Geode™ SC3200 Processor Data Book
265
Revision 5.1
Core Logic Module - SMI Status and ACPI Registers - Function 1
Table 6-34. F1BAR1+I/O Offset: ACPI Support Registers (Continued)
Bit
Description
13
SLP_EN (Sleep Enable). (Write Only) Allow the system to sequence into the sleeping state associated with the SLP_TYPx
(bits [12:10]).
0: Disable.
1: Enable.
This is a write only bit and reads of this bit always return a 0.
The ACPI state machine always waits for an SMI (any SMI) to be generated and serviced before transitioning into a Sleep
state.
If F1BAR1+I/O Offset 18h[9] = 1, an SMI is generated when SLP_EN is set.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[2].
Second level SMI status is reported at F1BAR0+I/O Offset 20h/22h[2].
12:10
SLP_TYPx (Sleep Type). Defines the type of Sleep state the system enters when SLP_EN (bit 13) is set.
000: Sleep State S0 (Full on)
001: Sleep State SL1
010: Sleep State SL2
011: Sleep State SL3
9:3
2
100: Sleep State SL4
101: Sleep State SL5 (Soft off)
110: Reserved
111: Reserved
Reserved. Set to 0.
GBL_RLS (Global Release). (Write Only) This write only bit is used by ACPI software to raise an event to the BIOS software (i.e., it generates an SMI to pass execution control to the BIOS).
0: Disable.
1: Enable.
This is a write only bit and reads of this bit always return a 0.
To generate an SMI, ACPI software writes the GBL_RLS bit which in turn sets the BIOS_STS bit (F1BAR1+I/O Offset
0Eh[0]) and raises a PME. For the PME to generate an SMI, set BIOS_EN (F1BAR1+I/O Offset 0Fh[0] to 1).
The top level SMI status is reported at F1BAR0+I/O offset 00h/02h.
Second level status is at F1BAR0+I/O Offset 22h[5].
1
BM_RLD (Bus Master RLD). If the processor is in the C3 state and a bus master request is generated, force the processor
to transition to the C0 state.
0: Disable.
1: Enable
0
SCI_EN (System Control Interrupt Enable). Globally selects power management events (PMEs) reported in PM1A_STS
and GPE0_STS (F1BAR1+I/O Offset 08h and 10h) to be either an SCI or SMI type of interrupt.
0: APM Mode, generates an SMI and status is reported at F1BAR0+I/O Offset 00h/02h[0].
1: ACPI Mode, generates an SCI if the corresponding PME enable bit is set and status is reported at F1BAR1+I/O Offset
08h and 10h.
Note:
This bit enables the ACPI state machine.
Offset 0Eh
7:1
0
ACPI_BIOS_STS Register (R/W)
Reset Value: 00h
Reserved. Must be set to 0.
BIOS_STS (BIOS Status Release). When 1 is written to the GLB_RLS bit (F1BAR1+I/O Offset 0Ch[2]), this bit is also set
to 1.
Write 1 to clear.
266
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - SMI Status and ACPI Registers - Function 1
Revision 5.1
Table 6-34. F1BAR1+I/O Offset: ACPI Support Registers (Continued)
Bit
Description
Offset 0Fh
7:2
1
ACPI_BIOS_EN Register (R/W)
Reset Value: 00h
Reserved. Must be set to 0.
BIOS_RLS (BIOS Release). (Write Only) When this bit is asserted, allow the BIOS to release control of the global lock.
0: Disable.
1: Enable.
This is a write only bit and reads of this bit always return a 0.
To generate an SCI, the BIOS writes the BIOS_RLS bit which in turn sets the GBL_STS bit (F1BAR1+I/O Offset 08h[5]) and
raises a PME. For the PME to generate an SCI, set GBL_EN (F1BAR1+I/O Offset 0Ah[5] to 1).
0
BIOS_EN (BIOS Enable). When this bit is asserted, allow SMI generation by ACPI software via writes to GBL_RLS
(F1BAR1+I/O Offset 0Ch[2]).
0: Disable.
1: Enable
Offset 10h-11h
GPE0_STS — General Purpose Event 0 PME/SCI Status Register (R/W)
Reset Value: xxxxh
Notes: 1) This is the top level of PME/SCI status reporting. There is no second level except for bit 3 (GPIOs) where the next level of
status is reported at F0BAR0+I/O Offset 0Ch/1Ch.
2) If SCI generation is not desired, the status bits are still set by the described conditions and can be used for monitoring purposes.
15:12
Reserved. Must be set to 0.
11
Reserved.
10
GPWIO2_STS. Indicates if PME was caused by activity on GPWIO2.
0: No.
1: Yes.
Write 1 to clear.
For the PME to generate an SCI:
1)
Ensure that GPWIO2 is enabled as an input (F1BAR1+I/O Offset 15h[2] = 0)
2)
Set F1BAR1+I/O Offset 12h[10] = 1 and F1BAR1+I/O Offset 0Ch[0] = 1. (See Note 2 in the general description of this
register above.)
If F1BAR1+I/O Offset 15h[6] = 1 it overrides these settings and GPWIO2 generates an SMI and the status is reported in
F1BAR0+00h/02h[0].
9
GPWIO1_STS. Indicates if PME was caused by activity on GPWIO1.
0: No.
1: Yes.
Write 1 to clear.
For the PME to generate an SCI:
1)
Ensure that GPWIO1 is enabled as an input (F1BAR1+I/O Offset 15h[1] = 0)
2)
Set F1BAR1+I/O Offset 12h[9] = 1 and F1BAR1+I/O Offset 0Ch[0] = 1. (See Note 2 in the general description of this
register above.)
If F1BAR1+I/O Offset 15h[5] = 1 it overrides these settings and GPWIO1 generates an SMI and the status is reported in
F1BAR0+00h/02h[0].
8
GPWIO0_STS. Indicates if PME was caused by activity on GPWIO0.
0: No.
1: Yes.
Write 1 to clear.
For the PME to generate an SCI:
1)
Ensure that GPWIO0 is enabled as an input (F1BAR1+I/O Offset 15h[0] = 0)
2)
Set F1BAR1+I/O Offset 12h[8] = 1 and F1BAR1+I/O Offset 0Ch[0] = 1. (See Note 2 in the general description of this
register above).
If F1BAR1+I/O Offset 15h[4] = 1 it overrides these settings and GPWIO0 generates an SMI and the status is reported in
F1BAR0+00h/02h[0].
AMD Geode™ SC3200 Processor Data Book
267
Revision 5.1
Core Logic Module - SMI Status and ACPI Registers - Function 1
Table 6-34. F1BAR1+I/O Offset: ACPI Support Registers (Continued)
Bit
Description
7
Reserved. Must be set to 0.
6
USB_STS. Indicates if PME was caused by a USB interrupt event.
0: No.
1: Yes.
Write 1 to clear.
For the PME to generate an SCI, set F1BAR1+I/O Offset 12h[6] = 1 and F1BAR1+I/O Offset 0Ch[0] = 1. (See Note 2 in the
general description of this register above.)
5
THRM_STS. Indicates if PME was caused by activity on THRM#.
0: No.
1: Yes.
Write 1 to clear.
For the PME to generate an SCI, set F1BAR1+I/O Offset 12h[5] = 1 and F1BAR1+I/O Offset 0Ch[0] = 1, (See Note 2 in the
general description of this register above,)
4
SMI_STS. Indicates if PME was caused by activity on the internal SMI# signal.
0: No.
1: Yes.
Write 1 to clear.
For the PME to generate an SCI, set F1BAR1+I/O Offset 12h[4] = 1 and F1BAR1+I/O Offset 0Ch[0] = 1. (See Note 2 in the
general description of this register above.)
3
GPIO_STS. Indicates if PME was caused by activity on any of the GPIOs (GPIO47-GPIO32 and GPIO15-GPIO0).
0: No.
1: Yes.
Write 1 to clear.
For the PME to generate an SCI, set F1BAR1+I/O Offset 12h[3] = 1 and F1BAR1+I/O Offset 0Ch[0] = 1. (See Note 2 in the
general description of this register above).
F0BAR0+I/O Offset 08h/18h selects which GPIOs are enabled to generate a PME. In addition, the selected GPIO must be
enabled as an input (F0BAR0+I/O Offset 20h and 24h).
2:1
0
Reserved. Reads as 0.
PWR_U_REQ_STS. Indicates if PME was caused by a power-up request event from the SuperI/O module.
0: No.
1: Yes.
Write 1 to clear.
For the PME to generate an SCI, set F1BAR1+I/O Offset 12h[0] = 1 and F1BAR1+I/O Offset 0Ch[0] = 1. (See Note 2 in the
general description of this register above.)
268
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - SMI Status and ACPI Registers - Function 1
Revision 5.1
Table 6-34. F1BAR1+I/O Offset: ACPI Support Registers (Continued)
Bit
Description
Offset 12h-13h
GPE0_EN — General Purpose Event 0 Enable Register (R/W)
Reset Value: 0000h
In order for the ACPI events described below to generate an SCI, the SCI_EN bit must also be set (F1BAR1+I/O Offset 0Ch[0] = 1).
The SCIs enabled in this register are globally enabled by setting F1BAR1+I/O Offset 0Ch[0] to 1. The status of the SCIs is reported in
F1BAR1+I/O Offset 10h.
15:12
Reserved.
11
Reserved.
10
GPWIO2_EN. Allow GPWIO2 to generate an SCI.
0: Disable.
1: Enable.
A fixed high-to-low or low-to-high transition (debounce period) of 31 µs exists in order for GPWIO2 to be recognized.
The setting of this bit can be overridden via F1BAR1+I/O Offset 15h[6] to force an SMI.
9
GPWIO1_EN. Allow GPWIO1 to generate an SCI.
0: Disable.
1: Enable.
See F1BAR1+I/O Offset 07h[3] for debounce information.
The setting of this bit can be overridden via F1BAR1+I/O Offset 15h[5] to force an SMI.
8
GPWIO0_EN. Allow GPWIO0 to generate an SCI.
0: Disable.
1: Enable.
See F1BAR1+I/O Offset 07h[3] for debounce information.
The setting of this bit can be overridden via F1BAR1+I/O Offset 15h[4] to force an SMI.
7
Reserved. Must be set to 0
6
USB_EN. Allow USB events to generate a SCI.
0: Disable.
1: Enable
5
THRM_EN. Allow THRM# to generate an SCI.
0: Disable.
1: Enable
4
SMI_EN. Allow SMI events to generate an SCI.
0: Disable.
1: Enable
3
GPIO_EN. Allow GPIOs (GPIO47-GPIO32 and GPIO15-GPIO0) to generate an SCI.
0: Disable.
1: Enable.
F0BAR0+I/O Offset 08h/18h selects which GPIOs are enabled for PME generation. This bit (GPIO_EN) globally enables
those selected GPIOs for generation of an SCI.
2:1
0
Reserved. Must be set to 0.
PWR_U_REQ_EN. Allow power-up request events from the SuperI/O module to generate an SCI.
0: Disable.
1: Enable.
A power-up request event is defined as any of the following events/activities: Modem, Telephone, Keyboard, Mouse, CEIR
(Consumer Electronic Infrared)
AMD Geode™ SC3200 Processor Data Book
269
Revision 5.1
Core Logic Module - SMI Status and ACPI Registers - Function 1
Table 6-34. F1BAR1+I/O Offset: ACPI Support Registers (Continued)
Bit
Description
Offset 14h
7:4
GPWIO Control Register 1 (R/W)
Reset Value: 00h
Reserved. Must be set to 0.
3
Reserved.
2
GPWIO2_POL. Select GPWIO2 polarity.
0: Active high
1: Active low
1
GPWIO1_POL. Select GPWIO1 polarity.
0: Active high
1: Active low
0
GPWIO0_POL. Select GPWIO0 polarity.
0: Active high
1: Active low
Offset 15h
GPWIO Control Register 2 (R/W)
7
Reserved.
6
GPWIO_SMIEN2. Allow GPWIO2 to generate an SMI.
Reset Value: 00h
0: Disable. (Default)
1: Enable.
A fixed high-to-low or low-to-high transition (debounce period) of 31 µs exists in order for GPWIO2 to be recognized.
Bit 2 of this register must be set to 0 (input) for GPWIO2 to be able to generate an SMI.
If asserted, this bit overrides the setting of F1BAR1+I/O Offset 12h[10] and its status is reported in F1BAR0+I/O Offset 00h/
02h[0].
5
GPWIO_SMIEN1. Allow GPWIO1 to generate an SMI.
0: Disable. (Default)
1: Enable.
See F1BAR1+I/O Offset 07h[3] for debounce information.
Bit 1 of this register must be set to 0 (input) for GPWIO1 to be able to generate an SMI.
If asserted, this bit overrides the setting of F1BAR1+I/O Offset 12h[9] and its status is reported in F1BAR0+I/O Offset 00h/
02h[0].
4
GPWIO_SMIEN0. Allow GPWIO0 to generate an SMI.
0: Disable. (Default)
1: Enable.
See F1BAR1+I/O Offset 07h[3] for debounce information.
Bit 0 of this register must be set to 0 (input) for GPWIO0 to be able to generate an SMI.
If enabled, this bit overrides the setting of F1BAR1+I/O Offset 12h[8] and its status is reported in F1BAR0+I/O Offset 00h/
02h[0].
3
Reserved.
2
GPWIO2_DIR. Selects the direction of GPWIO2.
0: Input.
1: Output.
1
GPWIO1_DIR. Selects the direction of GPWIO1.
0: Input.
1: Output.
0
GPWIO0_DIR. Selects the direction of the GPWIO0.
0: Input.
1: Output.
270
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - SMI Status and ACPI Registers - Function 1
Revision 5.1
Table 6-34. F1BAR1+I/O Offset: ACPI Support Registers (Continued)
Bit
Description
Offset 16h
GPWIO Data Register (R/W)
Reset Value: 00h
This register contains the direct values of the GPWIO2-GPWIO0 pins. Write operations are valid only for bits defined as outputs. Reads
from this register read the last written value if the pin is an output. The pins are configured as inputs or outputs in F1BAR1+I/O Offset
15h.
7:4
Reserved. Must be set to 0.
3
Reserved.
2
GPWIO2_DATA. Reflects the level of GPWIO2.
0: Low.
1: High.
A fixed high-to-low or low-to-high transition (debounce period) of 31 µs exists in order for GPWIO2 to be recognized.
1
GPWIO1_DATA. Reflects the level of GPWIO1.
0: Low.
1: High.
See F1BAR1+I/O Offset 07h[3] for debounce information.
0
GPWIO0_DATA. Reflects the level of GPWIO0.
0: Low.
1: High.
See F1BAR1+I/O Offset 07h[3] for debounce information.
Offset 17h
Reserved
Offset 18h-1Bh
31:17
16
ACPI SCI_ROUTING Register (R/W)
Reset Value: 00h
Reset Value: 00000F00h
Reserved.
PCTL_DELAYEN. Allow staggered delays on the activation and deactivation of the power control pins PWRCNT1,
PWRCNT2, and ONCTL# by 2 ms each.
0: Disable. (Default)
1: Enable.
15:12
11
Reserved. Must be set to 0.
PLVL3_SMIEN. Allow SMI generation when the PLVL3 Register (F1BAR1+I/O Offset 05h) is read.
0: Disable.
1: Enable. (Default)
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[2].
Second level SMI status is reported at F1BAR0+I/O Offset 20h/22h[4].
10
Reserved. Must be set to 0.
9
SLP_SMIEN. Allow SMI generation when the SLP_EN bit (F1BAR1+I/O Offset 0Ch[13]) is set.
0: Disable.
1: Enable. (Default)
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[2].
Second level SMI status is reported at F1BAR0+I/O Offset 20h/22h[2].
8
THT_SMIEN. Allow SMI generation when the THT_EN bit (F1BAR1+I/O Offset 00h[4]) is set.
0: Disable.
1: Enable. (Default)
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[2].
Second level SMI status is reported at F1BAR0+I/O Offset 20h/22h[1].
7:4
Reserved. Must be set to 0.
AMD Geode™ SC3200 Processor Data Book
271
Revision 5.1
Core Logic Module - SMI Status and ACPI Registers - Function 1
Table 6-34. F1BAR1+I/O Offset: ACPI Support Registers (Continued)
Bit
Description
3:0
SCI_IRQ_ROUTE. SCI is routed to:
0000: Disable
0001: IRQ1
0010: Reserved
0011: IRQ3
0100: IRQ4
0101: IRQ5
0010: IRQ6
0011: IRQ7
1000: IRQ8
1001: IRQ9
1010: IRQ10
1011: IRQ11
1100: IRQ12
1101: IRQ13
1110: IRQ14
1111: IRQ15
For more details see Section 6.2.6.3 "Programmable Interrupt Controller" on page 171.
Offset 1Ch-1Fh
Note:
ACPI Timer Register (RO)
Reset Value: xxxxxxxxh
This register can also be read at F1BAR0+I/O Offset 1Ch.
31:24
Reserved.
23:0
TMR_VAL. (Read Only) This bit field contains the running count of the power management timer.
Offset 20h
7:1
0
PM2_CNT — PM2 Control Register (R/W)
Reset Value: 00h
Reserved.
Arbiter Disable. Disables the PCI arbiter when set by the OS. Used during C3 transition.
0: Arbiter not disabled. (Default)
1: Disable arbiter.
Offset 21h-FFh
Reserved
Reset Value: 00h
The read value for these registers is undefined.
272
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module - IDE Controller Registers - Function 2
6.4.3
IDE Controller Registers - Function 2
The register space designated as Function 2 (F2) is used
to configure Channels 0 and 1 and the PCI portion of support hardware for the IDE controllers. The bit formats for
the PCI Header/Channels 0 and 1 Registers are given in
Table 6-35.
Located in the PCI Header Registers of F2 is a Base
Address Register (F2BAR4) used for pointing to the register space designated for support of the IDE controllers,
described later in this section.
Table 6-35. F2: PCI Header/Channels 0 and 1 Registers for IDE Controller Configuration
Bit
Description
Index 00h-01h
Vendor Identification Register (RO)
Reset Value: 100Bh
Index 02h-03h
Device Identification Register (RO)
Reset Value: 0502h
Index 04h-05h
PCI Command Register (R/W)
Reset Value: 0000h
15:3
2
Reserved. (Read Only)
Bus Master. Allow the Core Logic module bus mastering capabilities.
0: Disable.
1: Enable. (Default)
This bit must be set to 1.
1
Reserved. (Read Only)
0
I/O Space. Allow the Core Logic module to respond to I/O cycles from the PCI bus.
0: Disable.
1: Enable.
This bit must be enabled, in order to access I/O offsets through F2BAR4 (for more information see F2 Index 20h).
Index 06h-07h
PCI Status Register (RO)
Index 08h
Device Revision ID Register (RO)
Index 09h-0Bh
PCI Class Code Register (RO)
Reset Value: 0280h
Reset Value: 01h
Reset Value: 010180h
Index 0Ch
PCI Cache Line Size Register (RO)
Reset Value: 00h
Index 0Dh
PCI Latency Timer Register (RO)
Reset Value: 00h
Index 0Eh
PCI Header Type (RO)
Reset Value: 00h
Index 0Fh
PCI BIST Register (RO)
Reset Value: 00h
Index 10h-13h
Base Address Register 0 - F2BAR0 (RO)
Reset Value: 00000000h
Reserved. Reserved for possible future use by the Core Logic module.
Index 14h-17h
Base Address Register 1 - F2BAR1 (RO)
Reset Value: 00000000h
Reserved. Reserved for possible future use by the Core Logic module.
Index 18h-1Bh
Base Address Register 2 - F2BAR2 (RO)
Reset Value: 00000000h
Reserved. Reserved for possible future use by the Core Logic module.
Index 1Ch-1Fh
Base Address Register 3 - F2BAR3 (RO)
Reset Value: 00000000h
Reserved. Reserved for possible future use by the Core Logic module.
Index 20h-23h
Base Address Register 4 - F2BAR4 (R/W)
Reset Value: 00000001h
Base Address 0 Register. This register allows access to I/O mapped Bus Mastering IDE registers. Bits [3:0] are read only (0001), indicating a 16-byte I/O address range. Refer to Table 6-36 on page 277 for the IDE controller register bit formats and reset values.
31:4
Bus Mastering IDE Base Address.
3:0
Address Range. (Read Only)
Index 24h-2Bh
Reserved
Index 2Ch-2Dh
Subsystem Vendor ID (RO)
Reset Value: 100Bh
Index 2Eh-2Fh
Subsystem ID (RO)
Reset Value: 0502h
AMD Geode™ SC3200 Processor Data Book
Reset Value: 00h
273
Revision 5.1
Core Logic Module - IDE Controller Registers - Function 2
Table 6-35. F2: PCI Header/Channels 0 and 1 Registers for IDE Controller Configuration (Continued)
Bit
Description
Index 30h-3Fh
Reserved
Index 40h-43h
Channel 0 Drive 0 PIO Register (R/W)
Reset Value: 00h
Reset Value: 00009172h
If Index 44h[31] = 0, Format 0. Bits [15:0] configure the same timing control for both command and data.
Format 0 settings for a Fast-PCI clock frequency of 33.3 MHz:
— PIO Mode 0 = 00009172h
— PIO Mode 1 = 00012171h
— PIO Mode 2 = 00020080h
— PIO Mode 3 = 00032010h
— PIO Mode 4 = 00040010h
Format 0 settings for a Fast-PCI clock frequency of 66.7 MHz:
— PIO Mode 0 = 0000FFF4h
— PIO Mode 1 = 0001F353h
— PIO Mode 2 = 00028141h
— PIO Mode 3 = 00034231h
— PIO Mode 4 = 00041131h
Note:
31:20
All references to "cycle" in the following bit descriptions are to a Fast-PCI clock cycle.
Reserved. Must be set to 0.
19:16
PIOMODE. PIO mode.
15:12
t2I. Recovery time (value + 1 cycle).
11:8
t3. IDE_IOW# data setup time (value + 1 cycle).
7:4
t2W. IDE_IOW# width minus t3 (value + 1 cycle).
3:0
t1. Address Setup Time (value + 1 cycle).
If Index 44h[31] = 1, Format 1. Bits [31:0] allow independent timing control for both command and data.
Format 1 settings for a Fast-PCI clock frequency of 33.3 MHz:
— PIO Mode 0 = 9172D132h
— PIO Mode 1 = 21717121h
— PIO Mode 2 = 00803020h
— PIO Mode 3 = 20102010h
— PIO Mode 4 = 00100010h
Format 1 settings for a Fast-PCI clock frequency of 66.7 MHz:
— PIO Mode 0 = F8E4F8E4h
— PIO Mode 1 = 53F3F353h
— PIO Mode 2 = 13F18141h
— PIO Mode 3 = 42314231h
— PIO Mode 4 = 11311131h
Note:
All references to "cycle" in the following bit descriptions are to a Fast-PCI clock cycle.
31:28
t2IC. Command cycle recovery time (value + 1 cycle).
27:24
t3C. Command cycle IDE_IOW# data setup (value + 1 cycle).
23:20
t2WC. Command cycle IDE_IOW# pulse width minus t3 (value + 1 cycle).
19:16
t1C. Command cycle address setup time (value + 1 cycle).
15:12
t2ID. Data cycle recovery time (value + 1 cycle).
11:8
t3D. Data cycle IDE_IOW# data setup (value + 1 cycle).
7:4
t2WD. Data cycle IDE_IOW# pulse width minus t3 (value + 1 cycle).
3:0
t1D. Data cycle address Setup Time (value + 1 cycle).
274
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - IDE Controller Registers - Function 2
Revision 5.1
Table 6-35. F2: PCI Header/Channels 0 and 1 Registers for IDE Controller Configuration (Continued)
Bit
Description
Index 44h-47h
Channel 0 Drive 0 DMA Control Register (R/W)
Reset Value: 00077771h
The structure of this register depends on the value of bit 20.
If bit 20 = 0, Multiword DMA
Settings for a Fast-PCI clock frequency of 33.3 MHz:
— Multiword DMA Mode 0 = 00077771h
— Multiword DMA Mode 1 = 00012121h
— Multiword DMA Mode 2 = 00002020h
Settings for a Fast-PCI clock frequency of 66.7 MHz:
— Multiword DMA Mode 0 = 000FFFF3h
— Multiword DMA Mode 1 = 00035352h
— Multiword DMA Mode 2 = 00015151h
Note:
31
All references to "cycle" in the following bit descriptions are to a Fast-PCI clock cycle.
PIO Mode Format. This bit sets the PIO mode format for all channels and drives. Bit 31 of Offsets 2Ch, 34h, and 3Ch are R/
W, but have no function so are defined as reserved.
0: Format 0.
1
30:21
20
Format 1.
Reserved. Must be set to 0.
DMA Select. Selects type of DMA operation. 0: Multiword DMA
19:16
tKR. IDE_IOR# recovery time (4-bit) (value + 1 cycle).
15:12
tDR. IDE_IOR# pulse width (value + 1 cycle).
11:8
tKW. IDE_IOW# recovery time (4-bit) (value + 1 cycle).
7:4
tDW. IDE_IOW# pulse width (value + 1 cycle).
3:0
tM. IDE_CS[1:0]# to IDE_IOR#/IOW# setup; IDE_CS[1:0]# setup to IDE_DACK0#/DACK1#.
If bit 20 = 1, UltraDMA
Settings for a Fast-PCI clock frequency of 33.3 MHz:
— UltraDMA Mode 0 = 00921250h
— UltraDMA Mode 1 = 00911140h
— UltraDMA Mode 2 = 00911030h
Settings for a Fast-PCI clock frequency of 66.7 MHz:
— UltraDMA Mode 0 = 009436A1h
— UltraDMA Mode 1 = 00933481h
— UltraDMA Mode 2 = 00923261h
Note:
31
All references to "cycle" in the following bit descriptions are to a Fast-PCI clock cycle.
PIO Mode Format. This bit sets the PIO mode format for all channels and drives. Bit 31 of Offsets 2Ch, 34h, and 3Ch are R/
W, but have no function so are defined as reserved.
0: Format 0
1: Format 1
30:24
Reserved. Must be set to 0.
23:21
BSIZE. Input buffer threshold.
20
DMA Select. Selects type of DMA operation. 1: UltraDMA.
19:16
tCRC. CRC setup UDMA in IDE_DACK# (value + 1 cycle) (for host terminate CRC setup = tMLI + tSS).
15:12
tSS. UDMA out (value + 1 cycle).
11:8
tCYC. Data setup and cycle time UDMA out (value + 2 cycles).
7:4
tRP. Ready to pause time (value + 1 cycle). Note: tRFS + 1 tRP on next clock.
3:0
tACK. IDE_CS[1:0]# setup to IDE_DACK0#/DACK1# (value + 1 cycle).
AMD Geode™ SC3200 Processor Data Book
275
Revision 5.1
Core Logic Module - IDE Controller Registers - Function 2
Table 6-35. F2: PCI Header/Channels 0 and 1 Registers for IDE Controller Configuration (Continued)
Bit
Description
Index 48h-4Bh
Channel 0 Drive 1 PIO Register (R/W)
Reset Value: 00009172h
Channel 0 Drive 1 Programmed I/O Control Register. See F2 Index 40h for bit descriptions.
Index 4Ch-4Fh
Channel 0 Drive 1 DMA Control Register (R/W)
Reset Value: 00077771h
Channel 0 Drive 1 MDMA/UDMA Control Register. See F2 Index 44h for bit descriptions.
Note:
The PIO Mode format is selected in F2 Index 44h[31], bit 31 of this register is defined as reserved.
Index 50h-53h
Channel 1 Drive 0 PIO Register (R/W)
Reset Value: 00009172h
Channel 1 Drive 0 Programmed I/O Control Register. See F2 Index 40h for bit descriptions.
Index 54h-57h
Channel 1 Drive 0 DMA Control Register (R/W)
Reset Value: 00077771h
Channel 1 Drive 0 MDMA/UDMA Control Register. See F2 Index 44h for bit descriptions.
Note:
The PIO Mode format is selected in F2 Index 44h[31], bit 31 of this register is defined as reserved.
Index 58h-5Bh
Channel 1 Drive 1 PIO Register (R/W)
Reset Value: 00009172h
Channel 1 Drive 1 Programmed I/O Control Register. See F2 Index 40h for bit descriptions.
Index 5Ch-5Fh
Channel 1 Drive 1 DMA Control Register (R/W)
Reset Value: 00077771h
Channel 1 Drive 1 MDMA/UDMA Control Register. See F2 Index 44h for bit descriptions.
Note:
The PIO Mode format is selected in F2 Index 44h[31], bit 31 of this register is defined as reserved.
Index 60h-FFh
276
Reserved
Reset Value: 00h
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module - IDE Controller Registers - Function 2
6.4.3.1 IDE Controller Support Registers
F2 Index 20h, Base Address Register 4 (F2BAR4), points
to the base address of where the registers for IDE controller configuration are located. Table 6-36 gives the bit for-
mats of the I/O mapped IDE Controller Configuration
registers that are accessed through F2BAR4.
Table 6-36. F2BAR4+I/O Offset: IDE Controller Configuration Registers
Bit
Description
Offset 00h
7:4
3
IDE Bus Master 0 Command Register — Primary (R/W)
Reset Value: 00h
Reserved. Must be set to 0. Must return 0 on reads.
Read or Write Control. Sets the direction of bus master transfers.
0: PCI reads performed.
1: PCI writes performed.
This bit should not be changed when the bus master is active.
2:1
0
Reserved. Must be set to 0. Must return 0 on reads.
Bus Master Control. Controls the state of the bus master.
0: Disable master.
1: Enable master.
Bus master operations can be halted by setting this bit to 0. Once an operation has been halted, it cannot be resumed. If this
bit is set to 0 while a bus master operation is active, the command is aborted and the data transferred from the drive is discarded. This bit should be reset after completion of data transfer.
Offset 01h
Not Used
Offset 02h
IDE Bus Master 0 Status Register — Primary (R/W)
7
Reset Value: 00h
Simplex Mode. (Read Only) Indicates if both the primary and secondary channel operate independently.
0: Yes.
1: No (simplex mode).
6
Drive 1 DMA Enable. When asserted, allows Drive 1 to perform DMA transfers.
0: Disable.
1: Enable.
5
Drive 0 DMA Enable. When asserted, allows Drive 0 to perform DMA transfers.
0: Disable.
1: Enable.
4:3
2
Reserved. Must be set to 0. Must return 0 on reads.
Bus Master Interrupt. Indicates if the bus master detected an interrupt.
0: No.
1: Yes. Write 1 to clear.
1
Bus Master Error. Indicates if the bus master detected an error during data transfer.
0: No.
1: Yes. Write 1 to clear.
0
Bus Master Active. Indicates if the bus master is active.
0: No.
1: Yes.
Offset 03h
Not Used
Offset 04h-07h
31:2
IDE Bus Master 0 PRD Table Address — Primary (R/W)
Reset Value: 00000000h
Pointer to the Physical Region Descriptor Table. This bit field contains a PRD table pointer for IDE Bus Master 0.
When written, this field points to the first entry in a PRD table. Once IDE Bus Master 0 is enabled (Command Register bit 0
= 1), it loads the pointer and updates this field (by adding 08h) so that is points to the next PRD.
When read, this register points to the next PRD.
1:0
Reserved. Must be set to 0.
AMD Geode™ SC3200 Processor Data Book
277
Revision 5.1
Core Logic Module - IDE Controller Registers - Function 2
Table 6-36. F2BAR4+I/O Offset: IDE Controller Configuration Registers (Continued)
Bit
Description
Offset 08h
7:4
3
IDE Bus Master 1 Command Register — Secondary (R/W)
Reset Value: 00h
Reserved. Must be set to 0. Must return 0 on reads.
Read or Write Control. Sets the direction of bus master transfers.
0: PCI reads are performed.
1: PCI writes are performed.
This bit should not be changed when the bus master is active.
2:1
0
Reserved. Must be set to 0. Must return 0 on reads.
Bus Master Control. Controls the state of the bus master.
0: Disable master.
1: Enable master.
Bus master operations can be halted by setting this bit to 0. Once an operation has been halted, it cannot be resumed. If this
bit is set to 0 while a bus master operation is active, the command is aborted and the data transferred from the drive is discarded. This bit should be reset after completion of data transfer.
Offset 09h
Not Used
Offset 0Ah
IDE Bus Master 1 Status Register — Secondary (R/W)
7
Reserved. (Read Only)
6
Drive 1 DMA Capable. Allow Drive 1 to perform DMA transfers.
Reset Value: 00h
0: Disable.
1: Enable.
5
Drive 0 DMA Capable. Allow Drive 0 to perform DMA transfers.
0: Disable.
1: Enable.
4:3
2
Reserved. Must be set to 0. Must return 0 on reads.
Bus Master Interrupt. Indicates if the bus master detected an interrupt.
0: No.
1: Yes. Write 1 to clear.
1
Bus Master Error. Indicates if the bus master detected an error during data transfer.
0: No.
1: Yes. Write 1 to clear.
0
Bus Master Active. Indicates if the bus master is active.
0: No.
1: Yes.
Offset 0Bh
Not Used
Offset 0Ch-0Fh
31:2
IDE Bus Master 1 PRD Table Address — Secondary (R/W)
Reset Value: 00000000h
Pointer to the Physical Region Descriptor Table. This bit field contains a PRD table pointer for IDE Bus Master 1.
When written, this field points to the first entry in a PRD table. Once IDE Bus Master 1 is enabled (Command Register bit 0
= 1), it loads the pointer and updates this field (by adding 08h) so that is points to the next PRD.
When read, this register points to the next PRD.
1:0
278
Reserved. Must be set to 0.
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module - Audio Registers - Function 3
6.4.4
Audio Registers - Function 3
The register designated as Function 3 (F3) is used to configure the PCI portion of support hardware for the audio
registers. The bit formats for the PCI Header registers are
given in Table 6-37.
A Base Address register (F3BAR0), located in the PCI
Header registers of F3, is used for pointing to the register
space designated for support of audio, described later in
this section.
Table 6-37. F3: PCI Header Registers for Audio Configuration
Bit
Description
Index 00h-01h
Vendor Identification Register (RO)
Reset Value: 100Bh
Index 02h-03h
Device Identification Register (RO)
Reset Value: 0503h
Index 04h-05h
PCI Command Register (R/W)
Reset Value: 0000h
15:3
2
Reserved. (Read Only)
Bus Master. Allow the Core Logic module bus mastering capabilities.
0: Disable.
1: Enable. (Default)
This bit must be set to 1.
1
Memory Space. Allow the Core Logic module to respond to memory cycles from the PCI bus.
0: Disable.
1: Enable.
This bit must be enabled to access memory offsets through F3BAR0 (See F3 Index 10h).
0
Reserved. (Read Only)
Index 06h-07h
PCI Status Register (RO)
Index 08h
Device Revision ID Register (RO)
Index 09h-0Bh
PCI Class Code Register (RO)
Reset Value: 0280h
Reset Value: 00h
Reset Value: 040100h
Index 0Ch
PCI Cache Line Size Register (RO)
Reset Value: 00h
Index 0Dh
PCI Latency Timer Register (RO)
Reset Value: 00h
Index 0Eh
PCI Header Type (RO)
Reset Value: 00h
Index 0Fh
PCI BIST Register (RO)
Reset Value: 00h
Index 10h-13h
Base Address Register - F3BAR0 (R/W)
Reset Value: 00000000h
This register sets the base address of the memory mapped audio interface control register block. This is a 128-byte block of registers
used to control the audio FIFO and codec interface, as well as to support VSA SMIs. Bits [11:0] are read only (0000 0000 0000), indicating a 4 KB memory address range. Refer to Table 6-38 on page 280 for the audio configuration register bit formats and reset values.
31:12
Audio Interface Base Address
11:0
Address Range. (Read Only)
Index 14h-2Bh
Reserved
Index 2Ch-2Dh
Subsystem Vendor ID (RO)
Reset Value: 100Bh
Index 2Eh-2Fh
Subsystem ID (RO)
Reset Value: 0503h
Index 30h-FFh
Reserved
AMD Geode™ SC3200 Processor Data Book
Reset Value: 00h
Reset Value: 00h
279
Revision 5.1
Core Logic Module - Audio Registers - Function 3
6.4.4.1 Audio Support Registers
F3 Index 10h, Base Address Register 0 (F3BAR0), points
to the base address of where the registers for audio support are located. Table 6-38 gives the bit formats of the
memory mapped audio configuration registers that are
accessed through F3BAR0.
Table 6-38. F3BAR0+Memory Offset: Audio Configuration Registers
Bit
Description
Offset 00h-03h
31
Codec GPIO Status Register (R/W)
Reset Value: 00000000h
Codec GPIO Interface.
0: Disable.
1: Enable.
30
Codec GPIO SMI. When asserted, allows codec GPIO interrupt to generate an SMI.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[1].
Second level SMI status is reported at F3BAR0+Memory Offset 10h/12h[1].
29:21
20
Reserved. Must be set to 0.
Codec GPIO Status Valid. (Read Only) Indicates if the status read is valid.
0: Yes.
1: No.
19:0
Codec GPIO Pin Status. (Read Only) This field indicates the GPIO pin status that is received from the codec in slot 12 on
the SDATA_IN signal.
Offset 04h-07h
Codec GPIO Control Register (R/W)
Reset Value: 00000000h
31:20
Reserved. Must be set to 0.
19:0
Codec GPIO Pin Data. This field indicates the GPIO pin data that is sent to the codec in slot 12 on the SDATA_OUT signal.
Offset 08h-0Bh
31:24
23
Codec Status Register (R/W)
Reset Value: 00000000h
Codec Status Address. (Read Only) Address of the register for which status is being returned. This address comes from
slot 1 bits [19:12].
Codec Serial INT Enable. When asserted, allows codec serial interrupt to cause an SMI.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[1].
Second level SMI status is reported at F3BAR0+Memory Offset 10h/12h[1].
22
SYNC Pin. Sets SYNC high or low.
0: Low.
1: High.
21
SDATA_IN2_EN. When enabled, allows use of SDATA_IN2 input.
0: Disable.
1: Enable.
20
Audio Bus Master 5 AC97 Slot Select. Selects slot for Audio Bus Master 5 to receive data.
0: Slot 6.
1: Slot 11.
19
Audio Bus Master 4 AC97 Slot Select. Selects slot for Audio Bus Master 4 to transmit data.
0: Slot 6.
1: Slot 11.
18
Reserved. Must be set to 0.
17
Status Tag. (Read Only) The codec status data in bits [15:0] of this register is updated in the current AC97 frame. (codec
ready, slot1 and slot2 bits in tag slot are all set in current AC97 frame).
0: Not new.
1: New, updated in current frame.
280
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Audio Registers - Function 3
Revision 5.1
Table 6-38. F3BAR0+Memory Offset: Audio Configuration Registers (Continued)
Bit
Description
16
Codec Status Valid. (Read Only) Indicates if the status in bits [15:0] of this register is valid. This bit is high during slots 3 to
11 of the AC97 frame (i.e., for approximately 14.5 µs), for every frame.
0: No.
1: Yes.
15:0
Codec Status. (Read Only) This is the codec status data that is received from the codec in slot 2 on SDATA_IN. Only bits
[19:4] are used from slot 2. If this register is read with both bits 16 and 17 of this register set to 1, this field is updated in the
current AC97 frame, and codec status data is valid. This bit field is updated only if the codec sent status data.
Offset 0Ch-0Fh
Codec Command Register (R/W)
Reset Value: 00000000h
31:24
Codec Command Address. Address of the codec control register for which the command is being sent. This address goes
in slot 1 bits [19:12] on SDATA_OUT.
23:22
Codec Communication. Indicates the codec that the Core Logic module is communicating with.
00: Primary codec
01: Secondary codec
10: Third codec
11: Fourth codec
Only 00 and 01 are valid settings for this bit field.
21:17
16
Reserved. Must be set to 0.
Codec Command Valid. (Read Only) Indicates if the command in bits [15:0] of this register is valid.
0: No.
1: Yes.
This bit is set by hardware when a codec command is written to the Codec Command register. It remains set until the command has been sent to the codec.
15:0
Codec Command. This is the command being sent to the codec in bits [19:4] of slot 2 on SDATA_OUT.
Offset 10h-11h
Second Level Audio SMI Status Register (RC)
Reset Value: 0000h
The bits in this register contain second level SMI status reporting. Top level is reported at F1BAR0+I/O Offset 00h/02h[1]. Reading this
register clears the status bits at both the second and top levels. Note that bit 0 has a third level of status reporting which also must be
"read to clear".
A read-only “Mirror” version of this register exists at F3BAR0+I/O Memory Offset 12h. If the value of the register must be read without
clearing the SMI source (and consequently de-asserting SMI), F3BAR0+Memory Offset 12h can be read instead.
15:8
7
Reserved. Must be set to 0.
Audio Bus Master 5 SMI Status. Indicates if an SMI was caused by an event occurring on Audio Bus Master 5.
0: No.
1: Yes.
SMI generation is enabled when Audio Bus Master 5 is enabled (F3BAR0+Memory Offset 48h[0] = 1).
An SMI is then generated when the End of Page bit is set in the Audio Bus Master 5 SMI Status Register (F3BAR0+Memory
Offset 49h[0] = 1).
6
Audio Bus Master 4 SMI Status. Indicates if an SMI was caused by an event occurring on Audio Bus Master 4.
0: No.
1: Yes.
SMI generation is enabled when Audio Bus Master 4 is enabled (F3BAR0+Memory Offset 40h[0] = 1).
An SMI is then generated when the End of Page bit is set in the Audio Bus Master 4 SMI Status Register (F3BAR0+Memory
Offset 41h[0] = 1).
5
Audio Bus Master 3 SMI Status. Indicates if an SMI was caused by an event occurring on Audio Bus Master 3.
0: No.
1: Yes.
SMI generation is enabled when Audio Bus Master 3 is enabled (F3BAR0+Memory Offset 38h[0] = 1).
An SMI is then generated when the End of Page bit is set in the Audio Bus Master 3 SMI Status Register (F3BAR0+Memory
Offset 39h[0] = 1).
AMD Geode™ SC3200 Processor Data Book
281
Revision 5.1
Core Logic Module - Audio Registers - Function 3
Table 6-38. F3BAR0+Memory Offset: Audio Configuration Registers (Continued)
Bit
4
Description
Audio Bus Master 2 SMI Status. Indicates if an SMI was caused by an event occurring on Audio Bus Master 2.
0: No.
1: Yes.
SMI generation is enabled when Audio Bus Master 2 is enabled (F3BAR0+Memory Offset 30h[0] = 1).
An SMI is then generated when the End of Page bit is set in the Audio Bus Master 2 SMI Status Register (F3BAR0+Memory
Offset 31h[0] = 1).
3
Audio Bus Master 1 SMI Status. Indicates if an SMI was caused by an event occurring on Audio Bus Master 1.
0: No.
1: Yes.
SMI generation is enabled when Audio Bus Master 1 is enabled (F3BAR0+Memory Offset 28h[0] = 1).
An SMI is then generated when the End of Page bit is set in the Audio Bus Master 1 SMI Status Register (F3BAR0+Memory
Offset 29h[0] = 1).
2
Audio Bus Master 0 SMI Status. Indicates if an SMI was caused by an event occurring on Audio Bus Master 0.
0: No.
1: Yes.
SMI generation is enabled when Audio Bus Master 0 is enabled (F3BAR0+Memory Offset 20h[0] = 1).
An SMI is then generated when the End of Page bit is set in the Audio Bus Master 0 SMI Status Register (F3BAR0+Memory
Offset 21h[0] = 1).
1
Codec Serial or GPIO Interrupt SMI Status. Indicates if an SMI was caused by a serial or GPIO interrupt from codec.
0: No.
1: Yes.
SMI generation enabling for codec serial interrupt: F3BAR0+Memory Offset 08h[23] = 1.
SMI generation enabling for codec GPIO interrupt: F3BAR0+Memory Offset 00h[30] = 1.
0
I/O Trap SMI Status. Indicates if an SMI was caused by an I/O trap.
0: No.
1: Yes.
The next level (third level) of SMI status reporting is at F3BAR0+Memory Offset 14h.
Offset 12h-13h
Note:
15:8
7
Second Level Audio SMI Status Mirror Register (RO)
Reset Value: 0000h
The bits in this register contain second level SMI status reporting. Top level is reported at F1BAR0+I/O Offset 00h/02h[1].
Reading this register does not clear the status bits. See F3BAR0+Memory Offset 10h.
Reserved. Must be set to 0.
Audio Bus Master 5 SMI Status. Indicates if an SMI was caused by an event occurring on Audio Bus Master 5.
0: No.
1: Yes.
SMI generation is enabled when Audio Bus Master 5 is enabled (F3BAR0+Memory Offset 48h[0] = 1). An SMI is then generated when the End of Page bit is set in the SMI Status Register (F3BAR0+Memory Offset 49h[0] = 1). The End of Page bit
must be cleared before this bit can be cleared.
6
Audio Bus Master 4 SMI Status. Indicates if an SMI was caused by an event occurring on Audio Bus Master 4.
0: No.
1: Yes.
SMI generation is enabled when Audio Bus Master 4 is enabled (F3BAR0+Memory Offset 40h[0] = 1). An SMI is then generated when the End of Page bit is set in the SMI Status Register (F3BAR0+Memory Offset 41h[0] = 1). The End of Page bit
must be cleared before this bit can be cleared.
5
Audio Bus Master 3 SMI Status. Indicates if an SMI was caused by an event occurring on Audio Bus Master 3.
0: No.
1: Yes.
SMI generation is enabled when Audio Bus Master 3 is enabled (F3BAR0+Memory Offset 38h[0] = 1). An SMI is then generated when the End of Page bit is set in the SMI Status Register (F3BAR0+Memory Offset 39h[0] = 1). The End of Page bit
must be cleared before this bit can be cleared.
282
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Audio Registers - Function 3
Revision 5.1
Table 6-38. F3BAR0+Memory Offset: Audio Configuration Registers (Continued)
Bit
4
Description
Audio Bus Master 2 SMI Status. Indicates if an SMI was caused by an event occurring on Audio Bus Master 2.
0: No.
1: Yes.
SMI generation is enabled when Audio Bus Master 2 is enabled (F3BAR0+Memory Offset 30h[0] = 1). An SMI is then generated when the End of Page bit is set in the SMI Status Register (F3BAR0+Memory Offset 31h[0] = 1). The End of Page bit
must be cleared before this bit can be cleared.
3
Audio Bus Master 1 SMI Status. Indicates if an SMI was caused by an event occurring on Audio Bus Master 1.
0: No.
1: Yes.
SMI generation is enabled when Audio Bus Master 1 is enabled (F3BAR0+Memory Offset 28h[0] = 1). An SMI is then generated when the End of Page bit is set in the SMI Status Register (F3BAR0+Memory Offset 29h[0] = 1). The End of Page bit
must be cleared before this bit can be cleared.
2
Audio Bus Master 0 SMI Status. Indicates if an SMI was caused by an event occurring on Audio Bus Master 0.
0: No.
1: Yes.
SMI generation is enabled when Audio Bus Master 0 is enabled (F3BAR0+Memory Offset 20h[0] = 1). An SMI is then generated when the End of Page bit is set in the SMI Status Register (F3BAR0+Memory Offset 21h[0] = 1). The End of Page bit
must be cleared before this bit can be cleared.
1
Codec Serial or GPIO Interrupt SMI Status. Indicates if an SMI was caused by a serial or GPIO interrupt from codec.
0: No.
1: Yes.
SMI generation enabling for codec serial interrupt: F3BAR0+Memory Offset 08h[23] = 1.
SMI generation enabling for codec GPIO interrupt: F3BAR0+Memory Offset 00h[30] = 1.
0
I/O Trap SMI Status. Indicates if an SMI was caused by an I/O trap.
0: No.
1: Yes.
The next level (third level) of SMI status reporting is at F3BAR0+Memory Offset 14h.
Offset 14h-17h
Note:
I/O Trap SMI and Fast Write Status Register (RO/RC)
Reset Value: 00000000h
For the four SMI status bits (bits [13:10]), if the activity was a fast write to an even address, no SMI is generated regardless of
the DMA, MPU, or Sound Card status. If the activity was a fast write to an odd address, an SMI is generated but bit 13 is set to
a 1.
31:24
Fast Path Write Even Access Data. (Read Only) This bit field contains the data from the last Fast Path Write Even
access. These bits change only on a fast write to an even address.
23:16
Fast Path Write Odd Access Data. (Read Only) This bit field contains the data from the last Fast Path Write Odd access.
These bits change on a fast write to an odd address, and also on any non-fast write.
15
Fast Write A1. (Read Only) This bit contains the A1 value for the last Fast Write access.
14
Read or Write I/O Access. (Read Only) Indicates if the last trapped I/O access was a read or a write.
0: Read.
1: Write.
13
Sound Card or FM Trap SMI Status. (Read to Clear) Indicates if an SMI was caused by a trapped I/O access to the
Sound Card or FM I/O Trap.
0: No.
1: Yes. (See the note included in the general description of this register above.)
Fast Path Write must be enabled, F3BAR0+Memory Offset 18h[11] = 1, for the SMI to be reported here. If Fast Path Write is
disabled, the SMI is reported in bit 10 of this register.
This is the third level of SMI status reporting.
Second level SMI status is reported at F3BAR0+Memory Offset 10h/12h[0].
Top level is reported at F1BAR0+I/O Offset 00h/02h[1].
SMI generation enabling is at F3BAR0+Memory Offset 18h[2].
AMD Geode™ SC3200 Processor Data Book
283
Revision 5.1
Core Logic Module - Audio Registers - Function 3
Table 6-38. F3BAR0+Memory Offset: Audio Configuration Registers (Continued)
Bit
12
Description
DMA Trap SMI Status. (Read to Clear) Indicates if an SMI was caused by a trapped I/O access to the DMA I/O Trap.
0: No.
1: Yes. (See the note included in the general description of this register above.)
This is the third level of SMI status reporting.
Second level SMI status is reported at F3BAR0+Memory Offset 10h/12h[0].
Top level is reported at F1BAR0+I/O Offset 00h/02h[1].
SMI generation enabling is at F3BAR0+Memory Offset 18h[8:7].
11
MPU Trap SMI Status. (Read to Clear) Indicates if an SMI was caused by a trapped I/O access to the MPU I/O Trap.
0: No.
1: Yes. (See the note included in the general description of this register above.)
This is the third level of SMI status reporting.
Second level of SMI status is reported at F3BAR0+Memory Offset 10h/12h[0].
Top level is reported at F1BAR0+I/O Offset 00h/02h[1].
SMI generation enabling is at F3BAR0+Memory Offset 18h[6:5].
10
Sound Card or FM Trap SMI Status. (Read to Clear) Indicates if an SMI was caused by a trapped I/O access to the
Sound Card or FM I/O Trap.
0: No.
1: Yes. (See the note included in the general description of this register above.)
Fast Path Write must be disabled, F3BAR0+Memory Offset 18h[11] = 0, for the SMI to be reported here. If Fast Path Write
is enabled, the SMI is reported in bit 13 of this register.
This is the third level of SMI status reporting.
Second level of SMI status is reported at F3BAR0+Memory Offset 10h/12h[0].
Top level is reported at F1BAR0+I/O Offset 00h/02h[1].
SMI generation enabling is at F3BAR0+Memory Offset 18h[2].
9:0
X-Bus Address (Read Only). This bit field] contains the captured ten bits of X-Bus address.
Offset 18h-19h
15:12
11
I/O Trap SMI Enable Register (R/W
)Reset Value: 0000h
Reserved. Must be set to 0.
Fast Path Write Enable. Fast Path Write (an SMI is not generated on certain writes to specified addresses).
0: Disable.
1: Enable.
In Fast Path Write, the Core Logic module responds to writes to addresses: 388h, 38Ah, 38B, 2x0h, 2x2h, and 2x8h.
10:9
8
Fast Read. These two bits hold part of the response that the Core Logic module returns for reads to several I/O locations.
High DMA I/O Trap. If this bit is enabled and an access occurs at I/O Port C0h-DFh, an SMI is generated.
0:
Disable.
1:
Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[1].
Second level SMI status is reported at F3BAR0+Memory Offset 10h/12h[0].
Third level SMI status is reported at F3BAR0+Memory Offset 14h[12].
7
Low DMA I/O Trap. If this bit is enabled and an access occurs at I/O Port 00h-0Fh, an SMI is generated.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[1].
Second level SMI status is reported at F3BAR0+Memory Offset 10h/12h[0].
Third level SMI status is reported at F3BAR0+Memory Offset 14h[12].
6
High MPU I/O Trap. If this bit is enabled and an access occurs at I/O Port 330h-331h, an SMI is generated.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[1].
Second level SMI status is reported at F3BAR0+Memory Offset 10h/12h[0].
Third level SMI status is reported at F3BAR0+Memory Offset 14h[11].
284
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module - Audio Registers - Function 3
Table 6-38. F3BAR0+Memory Offset: Audio Configuration Registers (Continued)
Bit
5
Description
Low MPU I/O Trap. If this bit is enabled and an access occurs at I/O Port 300h-301h, an SMI is generated.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[1].
Second level SMI status is reported at F3BAR0+Memory Offset 10h/12h[0].
Third level SMI status is reported at F3BAR0+Memory Offset 14h[11].
4
Fast Path Read Enable/SMI Disable. When asserted, read Fast Path (an SMI is not generated on reads from specified
addresses).
0: Disable.
1: Enable.
In Fast Path Read the Core Logic module responds to reads of addresses: 388h-38Bh; 2x0h, 2x1, 2x2h, 2x3, 2x8 and 2x9h.
If neither sound card nor FM I/O mapping is enabled, then status read trapping is not possible.
3
FM I/O Trap. If this bit is enabled and an access occurs at I/O Port 388h-38Bh, an SMI is generated.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[1].
Second level SMI status is reported at F3BAR0+Memory Offset 10h/12h[0].
2
Sound Card I/O Trap. If this bit is enabled and an access occurs in the address ranges selected by bits [1:0], an SMI is
generated.
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[1].
Second level SMI status is reported at F3BAR0+Memory Offset 10h/12h[0].
Third level SMI status is reported at F3BAR0+Memory Offset 14h[10].
1:0
Sound Card Address Range Select. These bits select the address range for the sound card I/O trap.
00: I/O Port 220h-22Fh
01: I/O Port 240h-24Fh
Offset 1Ah-1Bh
15
10: I/O Port 260h-26Fh
11: I/O Port 280h-28Fh
Internal IRQ Enable Register (R/W)
Reset Value: 0000h
IRQ15 Internal. Configures IRQ15 for internal (software) or external (hardware) use.
0: External.
1: Internal.
14
IRQ14 Internal. Configures IRQ14 for internal (software) or external (hardware) use.
0: External.
1: Internal.
13
Reserved. Must be set to 0.
12
IRQ12 Internal. Configures IRQ12 for internal (software) or external (hardware) use.
0: External.
1: Internal.
11
IRQ11 Internal. Configures IRQ11 for internal (software) or external (hardware) use.
0: External.
1: Internal.
10
IRQ10 Internal. Configures IRQ10 for internal (software) or external (hardware) use.
0: External.
1: Internal.
9
IRQ9 Internal. Configures IRQ9 for internal (software) or external (hardware) use.
0: External.
1: Internal.
8
Reserved. Must be set to 0.
AMD Geode™ SC3200 Processor Data Book
285
Revision 5.1
Core Logic Module - Audio Registers - Function 3
Table 6-38. F3BAR0+Memory Offset: Audio Configuration Registers (Continued)
Bit
7
Description
IRQ7 Internal. Configures IRQ7 for internal (software) or external (hardware) use.
0: External.
1: Internal.
6
Reserved. Must be set to 0.
5
IRQ5 Internal. Configures IRQ5 for internal (software) or external (hardware) use.
0: External.
1: Internal.
4
IRQ4 Internal. Configures IRQ4 for internal (software) or external (hardware) use.
0: External.
1: Internal.
3
IRQ3 Internal. Configures IRQ3 for internal (software) or external (hardware) use.
0: External.
1: Internal.
2
Reserved. Must be set to 0.
1
IRQ1 Internal. Configures IRQ1 for internal (software) or external (hardware) use.
0: External.
1: Internal.
0
Reserved. Must be set to 0.
Offset 1Ch-1Fh
Note:
31
Internal IRQ Control Register (R/W)
Reset Value: 00000000h
Bits 31:16 of this register are Write Only. Reads to these bits always return a value of 0.
Mask Internal IRQ15. (Write Only)
0: Disable.
1: Enable.
30
Mask Internal IRQ14. (Write Only)
0: Disable.
1: Enable.
29
Reserved. (Write Only) Must be set to 0.
28
Mask Internal IRQ12. (Write Only)
0: Disable.
1: Enable.
27
Mask Internal IRQ11. (Write Only)
0: Disable.
1: Enable.
26
Mask Internal IRQ10. (Write Only)
0: Disable.
1: Enable.
25
Mask Internal IRQ9. (Write Only)
0: Disable.
1: Enable.
24
Reserved. (Write Only) Must be set to 0.
23
Mask Internal IRQ7. (Write Only)
0: Disable.
1: Enable.
22
Reserved. (Write Only) Must be set to 0.
21
Mask Internal IRQ5. (Write Only)
0: Disable.
1: Enable.
286
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - Audio Registers - Function 3
Revision 5.1
Table 6-38. F3BAR0+Memory Offset: Audio Configuration Registers (Continued)
Bit
Description
20
Mask Internal IRQ4. (Write Only)
0: Disable.
1: Enable.
19
Mask Internal IRQ3. (Write Only)
0: Disable.
1: Enable.
18
Reserved. (Write Only) Must be set to 0.
17
Mask Internal IRQ1. (Write Only)
0: Disable.
1: Enable.
16
Reserved. (Write Only) Must be set to 0.
15
Assert Masked Internal IRQ15.
0: Disable.
1: Enable.
14
Assert Masked Internal IRQ14.
0: Disable.
1: Enable.
13
Reserved. Set to 0.
12
Assert Masked Internal IRQ12.
0: Disable.
1: Enable.
11
Assert masked internal IRQ11.
0: Disable.
1: Enable.
10
Assert Masked Internal IRQ10.
0: Disable.
1: Enable.
9
Assert Masked Internal IRQ9.
0: Disable.
1: Enable.
8
Reserved. Set to 0.
7
Assert Masked Internal IRQ7.
0: Disable.
1: Enable.
6
Reserved. Set to 0.
5
Assert Masked Internal IRQ5.
0: Disable.
1: Enable.
4
Assert Masked Internal IRQ4.
0: Disable.
1: Enable.
3
Assert Masked Internal IRQ3.
0: Disable.
1: Enable.
2
Reserved. Must be set to 0.
AMD Geode™ SC3200 Processor Data Book
287
Revision 5.1
Core Logic Module - Audio Registers - Function 3
Table 6-38. F3BAR0+Memory Offset: Audio Configuration Registers (Continued)
Bit
Description
1
Assert Masked Internal IRQ1.
0: Disable.
1: Enable.
0
Reserved. Must be set to 0.
Offset 20h
Audio Bus Master 0 Command Register (R/W)
Reset Value: 00h
Audio Bus Master 0: Output to codec; 32-bit; Left and Right Channels; Slots 3 and 4.
7:4
Reserved. Must be set to 0. Must return 0 on reads.
3
Read or Write Control. Sets the transfer direction of the Audio Bus Master.
0: PCI reads are performed.
1: PCI writes are performed.
This bit must be set to 0 (read), and should not be changed when the bus master is active.
2:1
Reserved. Must be set to 0. Must return 0 on reads.
0
Bus Master Control. Controls the state of the Audio Bus Master.
0: Disable.
1: Enable.
Setting this bit to 1 enables the bus master to begin data transfers.
When writing 0 to this bit, the bus master must either be paused, or reach EOT. Writing 0 to this bit while the bus master is
operating may result in unpredictable behavior (and may crash the bus master state machine). The only recovery from such
unpredictable behavior is a PCI reset.
Offset 21h
Audio Bus Master 0 SMI Status Register (RC)
Reset Value: 00h
Audio Bus Master 0: Output to codec; 32-bit; Left and Right Channels; Slots 3 and 4.
7:2
1
Reserved.
Bus Master Error. Indicates if hardware encountered a second EOP before software has cleared the first.
0: No.
1: Yes.
If hardware encounters a second EOP (end of page) before software has cleared the first, it causes the bus master to pause
until this register is read to clear the error.
0
End of Page. Indicates if the bus master transferred data which is marked by EOP bit in the PRD table (bit 30).
0: No.
1: Yes.
Offset 22h-23h
Not Used
Offset 24h-27h
Audio Bus Master 0 PRD Table Address (R/W)
Reset Value: 00000000h
Audio Bus Master 0: Output to codec; 32-bit; Left and Right Channels; Slots 3 and 4.
31:2
Pointer to the Physical Region Descriptor Table. This bit field contains a PRD table pointer for Audio Bus Master 0.
When written, this register points to the first entry in a PRD table. Once Audio Bus Master 0 is enabled (Command Register
bit 0 = 1), it loads the pointer and updates this register (by adding 08h) so that it points to the next PRD.
When read, this register points to the next PRD.
1:0
Note:
Reserved. Must be set to 0.
The Physical Region Descriptor (PRD) table consists of one or more entries - each describing a memory region to or from
which data is to be transferred. Each entry consists of two DWORDs.
DWORD 0:
DWORD 1:
288
[31:0]
31
30
29
[28:16]
[15:0]
= Memory Region Physical Base Address
= End of Table Flag
= End of Page Flag
= Loop Flag (JMP)
= Reserved (0)
= Byte Count of the Region (Size)
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module - Audio Registers - Function 3
Table 6-38. F3BAR0+Memory Offset: Audio Configuration Registers (Continued)
Bit
Description
Offset 28h
Audio Bus Master 1 Command Register (R/W)
Reset Value: 00h
Audio Bus Master 1: Input from codec; 32-Bit; Left and Right Channels; Slots 3 and 4.
7:4
Reserved. Must be set to 0. Must return 0 on reads.
3
Read or Write Control. Set the transfer direction of Audio Bus Master 1.
0: PCI reads are performed.
1: PCI writes are performed.
This bit must be set to 1 (write) and should not be changed when the bus master is active.
2:1
Reserved. Must be set to 0. Must return 0 on reads.
0
Bus Master Control. Controls the state of the Audio Bus Master 1.
0: Disable.
1: Enable.
Setting this bit to 1 enables the bus master to begin data transfers. When writing this bit to 0, the bus master must be either
paused or reached EOT. Writing this bit to 0 while the bus master is operating results in unpredictable behavior (and may
cause a crash of the bus master state machine). The only recovery from this condition is a PCI reset.
Offset 29h
Audio Bus Master 1 SMI Status Register (RC)
Reset Value: 00h
Audio Bus Master 1: Input from codec; 32-Bit; Left and Right Channels; Slots 3 and 4.
7:2
1
Reserved.
Bus Master Error. Indicates if hardware encountered a second EOP before software has cleared the first.
0: No.
1: Yes.
If hardware encounters a second EOP (end of page) before software has cleared the first, it causes the bus master to pause
until this register is read to clear the error.
0
End of Page. Indicates if the bus master transferred data which is marked by EOP bit in the PRD table (bit 30).
0: No.
1: Yes.
Offset 2Ah-2Bh
Not Used
Offset 2Ch-2Fh
Audio Bus Master 1 PRD Table Address (R/W)
Reset Value: 00000000h
Audio Bus Master 1: Input from codec; 32-Bit; Left and Right Channels; Slots 3 and 4.
31:2
Pointer to the Physical Region Descriptor Table. This bit field is a PRD table pointer for Audio Bus Master 1.
When written, this register points to the first entry in a PRD table. Once Audio Bus Master 1 is enabled (Command Register
bit 0 = 1), it loads the pointer and updates this register (by adding 08h) so that it points to the next PRD.
When read, this register points to the next PRD.
1:0
Note:
Reserved. Must be set to 0.
The Physical Region Descriptor (PRD) table consists of one or more entries - each describing a memory region to or from
which data is to be transferred. Each entry consists of two DWORDs.
DWORD 0:
DWORD 1:
[31:0]
31
30
29
[28:16]
[15:0]
AMD Geode™ SC3200 Processor Data Book
= Memory Region Physical Base Address
= End of Table Flag
= End of Page Flag
= Loop Flag (JMP)
= Reserved (0)
= Byte Count of the Region (Size)
289
Revision 5.1
Core Logic Module - Audio Registers - Function 3
Table 6-38. F3BAR0+Memory Offset: Audio Configuration Registers (Continued)
Bit
Description
Offset 30h
Audio Bus Master 2 Command Register (R/W)
Reset Value: 00h
Audio Bus Master 2: Output to codec; 16-Bit; Slot 5.
7:4
Reserved. Must be set to 0. Must return 0 on reads.
3
Read or Write Control. Sets the transfer direction of Audio Bus Master 2.
0: PCI reads are performed.
1: PCI writes are performed.
This bit must be set to 0 (read) and should not be changed when the bus master is active.
2:1
Reserved. Must be set to 0. Must return 0 on reads.
0
Bus Master Control. Controls the state of the Audio Bus Master 2.
0: Disable.
1: Enable.
Setting this bit to 1 enables the bus master to begin data transfers. When writing 0 to this bit, the bus master must be either
paused or reached EOT. Writing 0 to this bit while the bus master is operating results in unpredictable behavior (and may
crash the bus master state machine). The only recovery from this condition is a PCI reset.
Offset 31h
Audio Bus Master 2 SMI Status Register (RC)
Reset Value: 00h
Audio Bus Master 2: Output to codec; 16-Bit; Slot 5.
7:2
1
Reserved.
Bus Master Error. Indicates if hardware encountered a second EOP before software has cleared the first.
0: No.
1: Yes.
If hardware encounters a second EOP (end of page) before software has cleared the first, it causes the bus master to pause
until this register is read to clear the error.
0
End of Page. Indicates if the Bus master transferred data which is marked by the EOP bit in the PRD table (bit 30).
0: No.
1: Yes.
Offset 32h-33h
Not Used
Reset Value: 00h
Offset 34h-37h
Audio Bus Master 2 PRD Table Address (R/W)
Reset Value: 00000000h
Audio Bus Master 2: Output to codec; 16-Bit; Slot 5.
31:2
Pointer to the Physical Region Descriptor Table. This bit field contains a PRD table pointer for Audio Bus Master 2.
When written, this field points to the first entry in a PRD table. Once Audio Bus Master 2 is enabled (Command Register bit
0 = 1), it loads the pointer and updates this register (by adding 08h) so that it points to the next PRD.
When read, this register points to the next PRD.
1:0
Note:
Reserved. Must be set to 0.
The Physical Region Descriptor (PRD) table consists of one or more entries - each describing a memory region to or from
which data is to be transferred. Each entry consists of two DWORDs.
DWORD 0:
DWORD 1:
290
[31:0]
31
30
29
[28:16]
[15:0]
= Memory Region Physical Base Address
= End of Table Flag
= End of Page Flag
= Loop Flag (JMP)
= Reserved (0)
= Byte Count of the Region (Size)
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module - Audio Registers - Function 3
Table 6-38. F3BAR0+Memory Offset: Audio Configuration Registers (Continued)
Bit
Description
Offset 38h
Audio Bus Master 3 Command Register (R/W)
Reset Value: 00h
Audio Bus Master 3: Input from codec; 16-Bit; Slot 5.
7:4
Reserved. Must be set to 0. Must return 0 on reads.
3
Read or Write Control. Sets the transfer direction of Audio Bus Master 3.
0: PCI reads are performed.
1: PCI writes are performed.
This bit must be set to 1 (write) and should not be changed when the bus master is active.
2:1
Reserved. Must be set to 0. Must return 0 on reads.
0
Bus Master Control. Controls the state of the Audio Bus Master 3.
0: Disable.
1: Enable.
Setting this bit to 1 enables the bus master to begin data transfers. When writing 0 to this bit, the bus master must be either
paused or have reached EOT. Writing 0 to this bit while the bus master is operating results in unpredictable behavior (and
may crash the bus master state machine). The only recovery from this condition is a PCI reset.
Offset 39h
Audio Bus Master 3 SMI Status Register (RC)
Reset Value: 00h
Audio Bus Master 3: Input from codec; 16-Bit; Slot 5.
7:2
1
Reserved.
Bus Master Error. Indicates if hardware encountered a second EOP before software cleared the first.
0: No.
1: Yes.
If hardware encounters a second EOP (end of page) before software cleared the first, it causes the bus master to pause
until this register is read to clear the error.
0
End of Page. Indicates if the bus master transferred data which is marked by the EOP bit in the PRD table (bit 30).
0: No.
1: Yes.
Offset 3Ah-3Bh
Not Used
Offset 3Ch-3Fh
Audio Bus Master 3 PRD Table Address (R/W)
Reset Value: 00000000h
Audio Bus Master 3: Input from codec; 16-Bit; Slot 5.
31:2
Pointer to the Physical Region Descriptor Table. This bit field contains is a PRD table pointer for Audio Bus Master 3.
When written, this field points to the first entry in a PRD table. Once Audio Bus Master 3 is enabled (Command Register bit
0 = 1), it loads the pointer and updates this register (by adding 08h) so that it points to the next PRD.
When read, this register points to the next PRD.
1:0
Note:
Reserved. Must be set to 0.
The Physical Region Descriptor (PRD) table consists of one or more entries - each describing a memory region to or from
which data is to be transferred. Each entry consists of two DWORDs.
DWORD 0:
DWORD 1:
[31:0]
31
30
29
[28:16]
[15:0]
AMD Geode™ SC3200 Processor Data Book
= Memory Region Physical Base Address
= End of Table Flag
= End of Page Flag
= Loop Flag (JMP)
= Reserved (0)
= Byte Count of the Region (Size)
291
Revision 5.1
Core Logic Module - Audio Registers - Function 3
Table 6-38. F3BAR0+Memory Offset: Audio Configuration Registers (Continued)
Bit
Description
Offset 40h
Audio Bus Master 4 Command Register (R/W)
Reset Value: 00h
Audio Bus Master 4: Output to codec; 16-Bit; Slot 6 or 11 (F3BAR0+Memory Offset 08h[19] selects slot).
7:4
Reserved. Must be set to 0. Must return 0 on reads.
3
Read or Write Control. Set the transfer direction of Audio Bus Master 4.
0: PCI reads are performed.
1: PCI writes are performed.
This bit must be set to 0 (read) and should not be changed when the bus master is active.
2:1
Reserved. Must be set to 0. Must return 0 on reads.
0
Bus Master Control. Controls the state of the Audio Bus Master 4.
0: Disable.
1: Enable.
Setting this bit to 1 enables the bus master to begin data transfers. When writing 0 to this bit, the bus master must be either
paused or have reached EOT. Writing 0 to this bit while the bus master is operating, results in unpredictable behavior (and
may crash the bus master state machine). The only recovery from this condition is a PCI reset.
Offset 41h
Audio Bus Master 4 SMI Status Register (RC)
Reset Value: 00h
Audio Bus Master 4: Output to codec; 16-Bit; Slot 6 or 11 (F3BAR0+Memory Offset 08h[19] selects slot).
7:2
1
Reserved.
Bus Master Error. Indicates if hardware encountered a second EOP before software cleared the first.
0: No.
1: Yes.
If hardware encounters a second EOP (end of page) before software cleared the first, it causes the bus master to pause
until this register is read to clear the error.
0
End of Page. Bus master transferred data which is marked by the EOP bit in the PRD table (bit 30).
0: No.
1: Yes.
Offset 42h-43h
Not Used
Offset 44h-47h
Audio Bus Master 4 PRD Table Address (R/W)
Reset Value: 00000000h
Audio Bus Master 4: Output to codec; 16-Bit; Slot 6 or 11 (F3BAR0+Memory Offset 08h[19] selects slot).
31:2
Pointer to the Physical Region Descriptor Table. This register is a PRD table pointer for Audio Bus Master 4.
When written, this register points to the first entry in a PRD table. Once Audio Bus Master 4 is enabled (Command Register
bit 0 = 1), it loads the pointer and updates this register (by adding 08h) so that it points to the next PRD.
When read, this register points to the next PRD.
1:0
Note:
Reserved. Must be set to 0.
The Physical Region Descriptor (PRD) table consists of one or more entries - each describing a memory region to or from
which data is to be transferred. Each entry consists of two DWORDs.
DWORD 0:
DWORD 1:
292
[31:0]
31
30
29
[28:16]
[15:0]
= Memory Region Physical Base Address
= End of Table Flag
= End of Page Flag
= Loop Flag (JMP)
= Reserved (0)
= Byte Count of the Region (Size)
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module - Audio Registers - Function 3
Table 6-38. F3BAR0+Memory Offset: Audio Configuration Registers (Continued)
Bit
Description
Offset 48h
Audio Bus Master 5 Command Register (R/W)
Reset Value: 00h
Audio Bus Master 5: Input from codec; 16-Bit; Slot 6 or 11 (F3BAR0+Memory Offset 08h[20] selects slot).
7:4
Reserved. Must be set to 0. Must return 0 on reads.
3
Read or Write Control. Set the transfer direction of Audio Bus Master 5.
0: PCI reads are performed.
1: PCI writes are performed.
This bit must be set to 1 (write) and should not be changed when the bus master is active.
2:1
Reserved. Must be set to 0. Must return 0 on reads.
0
Bus Master Control. Controls the state of the Audio Bus Master 5.
0: Disable.
1: Enable.
Setting this bit to 1 enables the bus master to begin data transfers. When writing 0 to this bit, the bus master must be either
paused or have reached EOT. Writing 0 to this bit while the bus master is operating, results in unpredictable behavior (and
may crash the bus master state machine). The only recovery from this condition is a PCI reset.
Offset 49h
Audio Bus Master 5 SMI Status Register (RC)
Reset Value: 00h
Audio Bus Master 5: Input from codec; 16-Bit; Slot 6 or 11 (F3BAR0+Memory Offset 08h[20] selects slot).
7:2
1
Reserved.
Bus Master Error. Indicates if hardware encountered a second EOP before software cleared the first.
0: No.
1: Yes.
If hardware encounters a second EOP (end of page) before software cleared the first, it causes the bus master to pause
until this register is read to clear the error.
0
End of Page. Indicates if the Bus master transferred data which is marked by the EOP bit in the PRD table (bit 30).
0: No.
1: Yes.
Offset 4Ah-4Bh
Not Used
Offset 4Ch-4Fh
Audio Bus Master 5 PRD Table Address (R/W)
Reset Value: 00000000h
Audio Bus Master 5: Input from codec; 16-Bit; Slot 6 or 11 (F3BAR0+Memory Offset 08h[20] selects slot).
31:2
Pointer to the Physical Region Descriptor Table. This bit field contains a PRD table pointer for Audio Bus Master 5.
When written, this register points to the first entry in a PRD table. Once Audio Bus Master 5 is enabled (Command Register
bit 0 = 1), it loads the pointer and updates this register (by adding 08h) so that it points to the next PRD.
When read, this register points to the next PRD.
1:0
Note:
Reserved. Must be set to 0.
The Physical Region Descriptor (PRD) table consists of one or more entries - each describing a memory region to or from
which data is to be transferred. Each entry consists of two DWORDs.
DWORD 0:
DWORD 1:
[31:0]
31
30
29
[28:16]
[15:0]
AMD Geode™ SC3200 Processor Data Book
= Memory Region Physical Base Address
= End of Table Flag
= End of Page Flag
= Loop Flag (JMP)
= Reserved (0)
= Byte Count of the Region (Size)
293
Revision 5.1
6.4.5
Core Logic Module - X-Bus Expansion Interface - Function 5
X-Bus Expansion Interface - Function 5
The register space designated as Function 5 (F5) is used
to configure the PCI portion of support hardware for
accessing the X-Bus Expansion support registers. The bit
formats for the PCI Header Registers are given in Table 639.
Located in the PCI Header Registers of F5 are six Base
Address Registers (F5BARx) used for pointing to the register spaces designated for X-Bus Expansion support,
described later in this section.
Table 6-39. F5: PCI Header Registers for X-Bus Expansion
Bit
Description
Index 00h-01h
Vendor Identification Register (RO)
Reset Value: 100Bh
Index 02h-03h
Device Identification Register (RO)
Reset Value: 0505h
Index 04h-05h
PCI Command Register (R/W)
Reset Value: 0000h
15:2
Reserved. (Read Only)
1
Memory Space. Allow the Core Logic module to respond to memory cycles from the PCI bus.
0: Disable.
1: Enable.
If F5BAR0, F5BAR1, F5BAR2, F5BAR3, F5BAR4, and F5BAR5 (F5 Index 10h, 14h, 18h, 1Ch, 20h, and 24h) are defined as
allowing access to memory mapped registers, this bit must be set to 1. BAR configuration is programmed through the corresponding mask register (see F5 Index 40h, 44h, 48h, 4Ch, 50h, and 54h)
0
I/O Space. Allow the Core Logic module to respond to I/O cycle from the PCI bus.
0: Disable.
1: Enable.
If F5BAR0, F5BAR1, F5BAR2, F5BAR3, F5BAR4, and F5BAR5 (F5 Index 10h, 14h, 18h, 1Ch, 20h, and 24h) are defined as
allowing access to I/O mapped registers, this bit must be set to 1. BAR configuration is programmed through the corresponding mask register (see F5 Index 40h, 44h, 48h, 4Ch, 50h, and 54h)
Index 06h-07h
PCI Status Register (RO)
Index 08h
Reset Value: 0280h
Device Revision ID Register (RO)
Index 09h-0Bh
Reset Value: 00h
PCI Class Code Register (RO)
Reset Value: 068000h
Index 0Ch
PCI Cache Line Size Register (RO)
Reset Value: 00h
Index 0Dh
PCI Latency Timer Register (RO)
Reset Value: 00h
Index 0Eh
PCI Header Type (RO)
Reset Value: 00h
Index 0Fh
PCI BIST Register (RO)
Reset Value: 00h
Index 10h-13h
Base Address Register 0 - F5BAR0 (R/W)
Reset Value: 00000000h
X-Bus Expansion Address Space. This register allows PCI access to I/O mapped X-Bus Expansion support registers. Bits [5:0] must
be set to 000001, indicating a 64-byte aligned I/O address space. Refer to Table 6-40 on page 298 for the X-Bus Expansion configuration register bit formats and reset values.
Note:
The size and type of accessed offsets can be reprogrammed through F5BAR0 Mask Register (F5 Index 40h).
31:6
X-Bus Expansion Base Address.
5:0
Address Range. This bit field must be set to 000001 for this register to operate correctly.
Index 14h-17h
Base Address Register 1 - F5BAR1 (R/W)
Reset Value: 00000000h
Reserved. Reserved for possible future use by the Core Logic module.
Configuration of this register is programmed through the F5BAR1 Mask Register (F5 Index 44h)
Index 18h-1Bh
Base Address Register 2 - F5BAR2 (R/W)
Reset Value: 00000000h
Reserved. Reserved for possible future use by the Core Logic module.
Configuration of this register is programmed through the F5BAR1 Mask Register (F5 Index 48h)
294
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - X-Bus Expansion Interface - Function 5
Revision 5.1
Table 6-39. F5: PCI Header Registers for X-Bus Expansion (Continued)
Bit
Description
Index 1Ch-1Fh
Base Address Register 3 - F5BAR3 (R/W)
Reset Value: 00000000h
Reserved. Reserved for possible future use by the Core Logic module.
Configuration of this register is programmed through the F5BAR3 Mask Register (F5 Index 4Ch).
Index 20h-23h
Base Address Register 4 - F5BAR4 (R/W)
Reset Value: 00000000h
Reserved. Reserved for possible future use by the Core Logic module.
Configuration of this register is programmed through the F5BAR4 Mask Register (F5 Index 50h).
Index 24h-27h
Base Address Register 5 - F5BAR5 (R/W)
Reset Value: 00000000h
Reserved. Reserved for possible future use by the Core Logic module.
Configuration of this register is programmed through the F5BAR5 Mask Register (F5 Index 54h).
Index 28h-2Bh
Reserved
Reset Value: 00h
Index 2Ch-2Dh
Subsystem Vendor ID (RO)
Reset Value: 100Bh
Index 2Eh-2Fh
Subsystem ID (RO)
Reset Value: 0505h
Index 30h-3Fh
Reserved
Index 40h-43h
F5BAR0 Mask Address Register (R/W)
Reset Value: 00h
Reset Value: FFFFFFC1h
To use F5BAR0, the mask register should be programmed first. The mask register defines the size of F5BAR0 and whether the
accessed offset registers are memory or I/O mapped.
Note:
Whenever a value is written to this mask register, F5BAR0 must also be written (even if the value for F5BAR0 has not
changed).
Memory Base Address Register (Bit 0 = 0)
31:4
Address Mask. Determines the size of the BAR.
— Every bit that is a 1 is programmable in the BAR.
— Every bit that is a 0 is fixed 0 in the BAR.
Since the address mask goes down to bit 4, the smallest memory region is 16 bytes, however, the PCI specification suggests not using less than a 4 KB address range.
3
Prefetchable. Indicates whether or not the data in memory is prefetchable. This bit should be set to 1 only if all the following
are true:
—
—
—
—
There are no side-effects from reads (i.e., the data at the location is not changed as a result of the read).
The device returns all bytes regardless of the byte enables.
Host bridges can merge processor writes into this range without causing errors.
The memory is not cached from the host processor.
0: Data is not prefetchable. This value is recommended if one or more of the above listed conditions is not true.
1: Data is prefetchable.
2:1
Type.
00: Located anywhere in the 32-bit address space
01: Located below 1 MB
10: Located anywhere in the 64-bit address space
11: Reserved
0
This bit must be set to 0, to indicate memory base address register.
I/O Base Address Register (Bit 0 = 1)
31:2
Address Mask. Determines the size of the BAR.
— Every bit that is a 1 is programmable in the BAR.
— Every bit that is a 0 is fixed 0 in the BAR.
Since the address mask goes down to bit 2, the smallest I/O region is 4 bytes, however, the PCI Specification suggests not
using less than a 4 KB address range.
1
Reserved. Must be set to 0.
0
This bit must be set to 1, to indicate an I/O base address register.
AMD Geode™ SC3200 Processor Data Book
295
Revision 5.1
Core Logic Module - X-Bus Expansion Interface - Function 5
Table 6-39. F5: PCI Header Registers for X-Bus Expansion (Continued)
Bit
Description
Index 44h-47h
F5BAR1 Mask Address Register (R/W)
Reset Value: 00000000h
To use F5BAR1, the mask register should be programmed first. The mask register defines the size of F5BAR1 and whether the
accessed offset registers are memory or I/O mapped. See F5 Index 40h (F5BAR0 Mask Address Register) above for bit descriptions.
Note:
Whenever a value is written to this mask register, F5BAR1 must also be written (even if the value for F5BAR1 has not
changed).
Index 48h-4Bh
F5BAR2 Mask Address Register (R/W)
Reset Value: 00000000h
To use F5BAR2, the mask register should be programmed first. The mask register defines the size of F5BAR2 and whether the
accessed offset registers are memory or I/O mapped. See F5 Index 40h (F5BAR0 Mask Address Register) above for bit descriptions.
Note:
Whenever a value is written to this mask register, F5BAR2 must also be written (even if the value for F5BAR2 has not
changed).
Index 4Ch-4Fh
F5BAR3 Mask Address Register (R/W)
Reset Value: 00000000h
To use F5BAR3, the mask register should be programmed first. The mask register defines the size of F5BAR3 and whether the
accessed offset registers are memory or I/O mapped. See F5 Index 40h (F5BAR0 Mask Address Register) above for bit descriptions.
Note:
Whenever a value is written to this mask register, F5BAR3 must also be written (even if the value for F5BAR3 has not
changed).
Index 50h-53h
F5BAR4 Mask Address Register (R/W)
Reset Value: 00000000h
To use F5BAR4, the mask register should be programmed first. The mask register defines the size of F5BAR4 and whether the
accessed offset registers are memory or I/O mapped. See F5 Index 40h (F5BAR0 Mask Address Register) above for bit descriptions.
Note:
Whenever a value is written to this mask register, F5BAR4 must also be written (even if the value for F5BAR4 has not
changed).
Index 54h-57h
F5BAR5 Mask Address Register (R/W)
Reset Value: 00000000h
To use F5BAR5, the mask register should be programmed first. The mask register defines the size of F5BAR5 and whether the
accessed offset registers are memory or I/O mapped. See F5 Index 40h (F5BAR0 Mask Address Register) above for bit descriptions.
Note:
Whenever a value is written to this mask register, F5BAR5 must also be written (even if the value for F5BAR5 has not
changed).
Index 58h
7:6
5
F5BARx Initialized Register (R/W)
Reset Value: 00h
Reserved. Must be set to 0.
F5BAR5 Initialized. This bit indicates if F5BAR5 (F5 Index 24h) has been initialized.
At reset this bit is cleared (0). Writing F5BAR5 sets this bit to 1. If this bit programmed to 0, the decoding of F5BAR5 is disabled until either this bit is set to 1 or F5BAR5 is written (which causes this bit to be set to 1).
4
F5BAR4 Initialized. This bit indicates if F5BAR4 (F5 Index 28h) has been initialized.
At reset this bit is cleared (0). Writing F5BAR4 sets this bit to 1. If this bit programmed to 0, the decoding of F5BAR4 is disabled until either this bit is set to 1 or F5BAR4 is written (which causes this bit to be set to 1).
3
F5BAR3 Initialized. This bit indicates if F5BAR3 (F5 Index 1Ch) has been initialized.
At reset this bit is cleared (0). Writing F5BAR3 sets this bit to 1. If this bit programmed to 0, the decoding of F5BAR3 is disabled until either this bit is set to 1 or F5BAR3 is written (which causes this bit to be set to 1).
2
F5BAR2 Initialized. This bit indicates if F5BAR2 (F5 Index 18h) has been initialized.
At reset this bit is cleared (0). Writing F5BAR2 sets this bit to 1. If this bit programmed to 0, the decoding of F5BAR2 is disabled until either this bit is set to 1 or F5BAR2 is written (which causes this bit to be set to 1).
1
F5BAR1 Initialized. This bit indicates if F5BAR1 (F5 Index 14h) has been initialized.
At reset this bit is cleared (0). Writing F5BAR1 sets this bit to 1. If this bit programmed to 0, the decoding of F5BAR1 is disabled until either this bit is set to 1 or F5BAR1 is written (which causes this bit to be set to 1).
0
F5BAR0 Initialized. This bit indicates if F5BAR0 (F5 Index 10h) has been initialized.
At reset this bit is cleared (0). Writing F5BAR0 sets this bit to 1. If this bit programmed to 0, the decoding of F5BAR0 is disabled until either this bit is set to 1 or F5BAR0 is written (which causes this bit to be set to 1).
Index 59h-5Fh
Reserved
Reset Value: xxh
Index 60h-63h
Scratchpad: Usually used for Device Number (R/W)
Reset Value: 00000000h
BIOS writes a value, of the Device number. Expected value: 00003200h.
296
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - X-Bus Expansion Interface - Function 5
Revision 5.1
Table 6-39. F5: PCI Header Registers for X-Bus Expansion (Continued)
Bit
Description
Index 64h-67h
Scratchpad: Usually used for Configuration Block Address (R/W)
Reset Value: 00000000h
BIOS writes a value, of the Configuration Block Address.
Index 68h-FFh
AMD Geode™ SC3200 Processor Data Book
Reserved
297
Revision 5.1
Core Logic Module - X-Bus Expansion Interface - Function 5
6.4.5.1 X-Bus Expansion Support Registers
F5 Index 10h, Base Address Register 0 (F5BAR0) set the
base address that allows PCI access to additional I/O Con-
trol support registers. Table 6-40 shows the support registers accessed through F5BAR0.
Table 6-40. F5BAR0+I/O Offset: X-Bus Expansion Registers
Bit
Description
Offset 00h-03h
31:28
27
I/O Control Register 1 (R/W)
Reset Value: 010C0007h
Reserved.
IO_ENABLE_SIO_IR (Enable Integrated SIO Infrared).
0: Disable.
1: Enable.
26:25
IO_SIOCFG_IN (Integrated SIO Input Configuration). These two bits can be used to disable the integrated SIO totally or
limit/control the base address.
00: Integrated SIO disable.
01: Integrated SIO configuration access disable.
10: Integrated SIO base address 02Eh/02Fh enable.
11: Integrated SIO base address 015Ch/015Dh enable.
24
IO_ENABLE_SIO_DRIVING_ISA_BUS (Enable Integrated SIO ISA Bus Control). Allow the integrated SIO to drive the
internal ISA bus.
0: Disable.
1: Enable. (Default)
23:21
20
Reserved. Set to 0.
IO_USB_SMI_PWM_EN (USB Internal SMI). Route USB-generated SMI to SMI Status Register in F1BAR0+I/O Offset
00h/02h[14].
0: Disable.
1: Enable.
19
IO_USB_SMI_EN (USB SMI Configuration). Allow USB-generated SMIs.
0: Disable
1: Enable.
If bits 19 and 20 are enabled, the SMI generated by the USB is reported via the Top Level SMI status register at F1BAR0+I/
O Offset 00h/02h[14].
If only bit 19 is enabled, the USB can generate an SMI but there is no status reporting.
18
IO_USB_PCI_EN (USB). Enables USB ports.
0: Disable.
1: Enable.
17:0
298
Reserved.
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - X-Bus Expansion Interface - Function 5
Revision 5.1
Table 6-40. F5BAR0+I/O Offset: X-Bus Expansion Registers (Continued)
Bit
Description
Offset 04h-07h
31:2
1
I/O Control Register 2 (R/W)
Reset Value: 00000002h
Reserved. Write as read.
Video Processor Access Enable. Allows access to video processor using F4BAR0.
0: Disable.
1: Enable. (Default)
Note:
0
This bit is readable after the register (F5BAR0+Offset 04h) has been written once.
IO_STRAP_IDSEL_SELECT (IDSEL Strap Override).
0: IDSEL: AD28 for Chipset Register Space (F0-F5), AD29 for USB Register Space (PCIUSB).
1: IDSEL: AD26 for Chipset Register Space (F0-F5), AD27 for USB Register Space (PCIUSB).
Offset 08h-0Bh
I/O Control Register 3 (R/W)
Reset Value: 00009000h
31:16
Reserved. Write as read.
15:13
IO_USB_XCVR_VADJ (USB Voltage Adjustment Connection). These bits connect to the voltage adjustment interface on
the three USB transceivers. Default = 100.
12:8
IO_USB_XCVT_CADJ (USB Current Adjustment). These bits connect to the current adjustment interface on the three
USB transceivers. Default = 10000.
7
IO_TEST_PORT_EN (Debug Test Port Enable).
0: Disable
1: Enable
6:0
IO_TEST_PORT_REG (Debug Port Pointer). These bits are used to point to the 16-bit slice of the test port bus.
AMD Geode™ SC3200 Processor Data Book
299
Revision 5.1
6.4.6
Core Logic Module - USB Controller Registers - PCIUSB
USB Controller Registers - PCIUSB
The registers designated as PCIUSB are 32-bit registers
decoded from the PCI address bits [7:2] and C/BE[3:0]#,
when IDSEL is high, AD[10:8] select the appropriate function, and AD[1:0] are 00.
The PCI Configuration registers are listed in Table 6-41.
They can be accessed as any number of bytes within a single 32-bit aligned unit. They are selected by the PCI-standard Index and Byte-Enable method.
In the PCI Configuration space, there is one Base Address
Register (BAR), at Index 10h, which is used to map the
USB Host Controller's operational register set into a 4K
memory space. Once the BAR register has been initialized,
and the PCI Command register at Index 04h has been set
to enable the Memory space decoder, these “USB Controller” registers are accessible.
The memory-mapped USB Controller registers are listed in
Table 6-42. They follow the Open Host Controller Interface
(OHCI) specification. Registers marked as “Reserved”, and
reserved bits within a register, should not be changed by
software.
Table 6-41. PCIUSB: USB PCI Configuration Registers
Bit
Description
Index 00h-01h
Vendor Identification Register (RO)
Reset Value: 0E11h
Index 02h-03h
Device Identification Register (RO)
Reset Value: A0F8h
Index 04h-05h
Command Register (R/W)
15:10
Reset Value: 00h
Reserved. Must be set to 0.
9
Fast Back-to-Back Enable. (Read Only) USB only acts as a master to a single device, so this functionality is not needed.
It is always disabled (i.e., this bit must always be set to 0).
8
SERR#. When this bit is enabled, USB asserts SERR# when it detects an address parity error.
0: Disable.
1: Enable.
7
6
Wait Cycle Control. USB does not need to insert a wait state between the address and data on the AD lines. It is always
disabled (i.e., this bit is set to 0).
Parity Error. USB asserts PERR# when it is the agent receiving data and it detects a data parity error.
0: Disable.
1: Enable.
5
VGA Palette Snoop Enable. (Read Only) USB does not support this function. It is always disabled (i.e., this bit is set to
0).
4
Memory Write and Invalidate. Allow USB to run Memory Write and Invalidate commands.
0: Disable.
1: Enable.
The Memory Write and Invalidate Command only occurs if the cache-line size is set to 32 bytes and the memory write is
exactly one cache line.
This bit must be set to 0.
3
2
Special Cycles. USB does not run special cycles on PCI. It is always disabled (i.e., this bit is set to 0).
PCI Master Enable. Allow the USB to run PCI master cycles.
0: Disable.
1: Enable.
1
Memory Space. Allow the USB to respond as a target to memory cycles from the PCI bus.
0: Disable.
1: Enable.
0
I/O Space. Allow the USB to respond as a target to I/O cycles from the PCI bus.
0
Disable.
1: Enable.
300
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - USB Controller Registers - PCIUSB
Revision 5.1
Table 6-41. PCIUSB: USB PCI Configuration Registers (Continued)
Bit
Description
Index 06h-07h
Status Register (R/W)
Reset Value: 0280h
The PCI specification defines this register to record status information for PCI related events. This is a read/write register. However,
writes can only reset bits. A bit is reset whenever the register is written and the data in the corresponding bit location is a 1.
15
Detected Parity Error. This bit is set to 1 whenever the USB detects a parity error, even if the Parity Error (Response)
Detection Enable Bit (Command Register, bit 6) is disabled.
Write 1 to clear.
14
SERR# Status. This bit is set whenever the USB detects a PCI address error.
Write 1 to clear.
13
Received Master Abort Status. This bit is set when the USB, acting as a PCI master, aborts a PCI bus memory cycle.
Write 1 to clear.
12
Received Target Abort Status. This bit is set when a USB generated PCI cycle (USB is the PCI master) is aborted by a
PCI target.
Write 1 to clear.
11
Signaled Target Abort Status. This bit is set whenever the USB signals a target abort.
Write 1 to clear.
10:9
DEVSEL# Timing. (Read Only) These bits indicate the DEVSEL# timing when performing a positive decode. Since
DEVSEL# is asserted to meet the medium timing, these bits are encoded as 01b.
8
Data Parity Reported. (Read Only) This bit is set to 1 if the Parity Error Response bit (Command Register bit 6) is set,
and the USB detects PERR# asserted while acting as PCI master (whether or not PERR# was driven by USB).
7
Fast Back-to-Back Capable. The USB supports fast back-to-back transactions when the transactions are not to the same
agent.
This bit is always 1.
6:0
Reserved. Must be set to 0.
Index 08h
Device Revision ID Register (RO)
Index 09h-0Bh
PCI Class Code Register (RO)
Reset Value: 08h
Reset Value: 0C0310h
This register identifies the generic function of the USB the specific register level programming interface. The Base Class is 0Ch (Serial
Bus Controller). The Sub Class is 03h (Universal Serial Bus). The Programming Interface is 10h (OpenHCI).
Index 0Ch
Cache Line Size Register (R/W)
Reset Value: 00h
This register identifies the system cache-line size in units of 32-bit WORDs. The USB only stores the value of bit 3 in this register since
the cache-line size of 32 bytes is the only value applicable to the design. Any value other than 08h written to this register is read back
as 00h.
Index 0Dh
Latency Timer Register (R/W)
Reset Value: 00h
This register identifies the value of the latency timer in PCI clocks for PCI bus master cycles. Bits [2:0] of this register are always set to
0.
Index 0Eh
Header Type Register (RO)
Reset Value: 00h
This register identifies the type of the predefined header in the configuration space. Since the USB is a single function device and not a
PCI-to-PCI bridge, this byte should be read as 00h.
Index 0Fh
BIST Register (RO)
Reset Value: 00h
This register identifies the control and status of Built-In Self-Test (BIST). The USB does not implement BIST, so this register is read
only.
Index 10h-13h
Base Address Register - USB_BAR0 (R/W)
31:12
Base Address. POST writes the value of the memory base address to this register.
11:4
Always 0. Indicates that a 4 KB address range is requested.
3
2:1
0
Reset Value: 00000000h
Always 0. Indicates that there is no support for prefetchable memory.
Always 0. Indicates that the base register is 32-bits wide and can be placed anywhere in 32-bit memory space.
Always 0. Indicates that the operational registers are mapped into memory space.
AMD Geode™ SC3200 Processor Data Book
301
Revision 5.1
Core Logic Module - USB Controller Registers - PCIUSB
Table 6-41. PCIUSB: USB PCI Configuration Registers (Continued)
Bit
Description
Index 14h-2Bh
Reserved
Index 2Ch-2Dh
Subsystem Vendor ID (RO)
Reset Value: 0E11h
Index 2Eh-2Fh
Subsystem ID (RO)
Reset Value: A0F8h
Index 30h-3Bh
Reserved
Reset Value: 00h
Interrupt Line Register (R/W)
Reset Value: 00h
Index 3Ch
Reset Value: 00h
This register identifies the system interrupt controllers to which the device’s interrupt pin is connected. The value of this register is used
by device drivers and has no direct meaning to USB.
Index 3Dh
Interrupt Pin Register (R/W)
Reset Value: 01h
This register selects which interrupt pin the device uses. USB uses INTA# after reset. INTB#, INTC# or INTD# can be selected by writing 2, 3 or 4, respectively.
Index 3Eh
Min. Grant Register (RO)
Reset Value: 00h
This register specifies how long a burst is needed by the USB, assuming a clock rate of 33 MHz. The value in this register specifies a
period of time in units of 1/4 microsecond.
Index 3Fh
Max. Latency Register (RO)
Reset Value: 50h
This register specifies how often (in units of 1/4 microsecond) the USB needs access to the PCI bus assuming a clock rate of 33 MHz.
Index 40h-43h
ASIC Test Mode Enable Register (R/W)
Reset Value: 000F0000h
Used for internal debug and test purposes only.
Index 44h
ASIC Operational Mode Enable Register (R/W)
7:1
Write Only. Read as 0s.
0
Data Buffer Region 16
Reset Value: 00h
0: The size of the region for the data buffer is 32 bytes.
1: The size of the region for the data buffer is 16 bytes.
Index 45h-FFh
302
Reserved
Reset Value: 00h
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - USB Controller Registers - PCIUSB
Revision 5.1
Table 6-42. USB_BAR+Memory Offset: USB Controller Registers
Bit
Description
Offset 00h-03h
HcRevision Register (RO)
Reset Value = 00000110h
31:8
Reserved. Read/Write 0s.
7:0
Revision (Read Only). Indicates the Open HCI Specification revision number implemented by the Hardware. USB supports 1.0 specification. (X.Y = XYh).
Offset 04h-07h
31:11
HcControl Register (R/W)
Reset Value = 00000000h
Reserved. Read/Write 0s.
10
RemoteWakeupConnectedEnable. If a remote wakeup signal is supported, this bit enables that operation. Since there is
no remote wakeup signal supported, this bit is ignored.
9
RemoteWakeupConnected (Read Only). This bit indicated whether the HC supports a remote wakeup signal. This implementation does not support any such signal. The bit is hard-coded to 0.
8
InterruptRouting. This bit is used for interrupt routing:
0: Interrupts routed to normal interrupt mechanism (INT).
1: Interrupts routed to SMI.
7:6
HostControllerFunctionalState. This field sets the HC state. The HC may force a state change from UsbSuspend to
UsbResume after detecting resume signaling from a downstream port. States are:
00: UsbReset
01: UsbResume
10: UsbOperational
11: UsbSuspend
5
BulkListEnable. When set, this bit enables processing of the Bulk list.
4
ControlListEnable. When set, this bit enables processing of the Control list.
3
IsochronousEnable. When clear, this bit disables the Isochronous List when the Periodic List is enabled (so Interrupt EDs
may be serviced). While processing the Periodic List, the HC will check this bit when it finds an isochronous ED.
2
PeriodicListEnable. When set, this bit enables processing of the Periodic (interrupt and isochronous) list. The HC checks
this bit prior to attempting any periodic transfers in a frame.
1:0
ControlBulkServiceRatio. Specifies the number of Control Endpoints serviced for every Bulk Endpoint. Encoding is N-1
where N is the number of Control Endpoints (i.e., 00: 1 Control Endpoint; 11: 3 Control Endpoints).
Offset 08h-0Bh
HcCommandStatus Register (R/W)
Reset Value = 00000000h
31:18
Reserved. Read/Write 0s.
17:16
ScheduleOverrunCount. This field increments every time the SchedulingOverrun bit in HcInterruptStatus is set. The
count wraps from 11 to 00.
15:4
Reserved. Read/Write 0s.
3
OwnershipChangeRequest. When set by software, this bit sets the OwnershipChange field in HcInterruptStatus. The bit
is cleared by software.
2
BulkListFilled. Set to indicate there is an active ED on the Bulk List. The bit may be set by either software or the HC and
cleared by the HC each time it begins processing the head of the Bulk List.
1
ControlListFilled. Set to indicate there is an active ED on the Control List. It may be set by either software or the HC and
cleared by the HC each time it begins processing the head of the Control List.
0
HostControllerReset. This bit is set to initiate a software reset. This bit is cleared by the HC upon completion of the reset
operation.
Offset 0Ch-0Fh
HcInterruptStatus Register (R/W)
Reset Value = 00000000h
31
Reserved. Read/Write 0s.
30
OwnershipChange. This bit is set when the OwnershipChangeRequest bit of HcCommandStatus is set.
29:7
Reserved. Read/Write 0s.
AMD Geode™ SC3200 Processor Data Book
303
Revision 5.1
Core Logic Module - USB Controller Registers - PCIUSB
Table 6-42. USB_BAR+Memory Offset: USB Controller Registers (Continued)
Bit
Description
6
RootHubStatusChange. This bit is set when the content of HcRhStatus or the content of any HcRhPortStatus register has
changed.
5
FrameNumberOverflow. Set when bit 15 of FrameNumber changes value.
4
UnrecoverableError (Read Only). This event is not implemented and is hard-coded to 0. Writes are ignored.
3
ResumeDetected. Set when HC detects resume signaling on a downstream port.
2
StartOfFrame. Set when the Frame Management block signals a Start of Frame event.
1
WritebackDoneHead. Set after the HC has written HcDoneHead to HccaDoneHead.
0
SchedulingOverrun. Set when the List Processor determines a Schedule Overrun has occurred.
Note:
All bits are set by hardware and cleared by software.
Offset 10h-13h
HcInterruptEnable Register (R/W)
Reset Value = 00000000h
31
MasterInterruptEnable. This bit is a global interrupt enable. A write of 1 allows interrupts to be enabled via the specific
enable bits listed above.
30
OwnershipChangeEnable.
0: Ignore.
1: Enable interrupt generation due to Ownership Change.
29:7
6
Reserved. Read/Write 0s.
RootHubStatusChangeEnable.
0: Ignore.
1: Enable interrupt generation due to Root Hub Status Change.
5
FrameNumberOverflowEnable.
0: Ignore.
1: Enable interrupt generation due to Frame Number Overflow.
4
UnrecoverableErrorEnable. This event is not implemented. All writes to this bit are ignored.
3
ResumeDetectedEnable.
0: Ignore.
1: Enable interrupt generation due to Resume Detected.
2
StartOfFrameEnable.
0: Ignore.
1: Enable interrupt generation due to Start of Frame.
1
WritebackDoneHeadEnable.
0: Ignore.
1: Enable interrupt generation due to Writeback Done Head.
0
SchedulingOverrunEnable.
0: Ignore.
1: Enable interrupt generation due to Scheduling Overrun.
Note:
Writing a 1 to a bit in this register sets the corresponding bit, while writing a 0 leaves the bit unchanged.
Offset 14h-17h
HcInterruptDisable Register (R/W)
Reset Value = 00000000h
31
MasterInterruptEnable. Global interrupt disable. A write of 1 disables all interrupts.
30
OwnershipChangeEnable.
0: Ignore.
1: Disable interrupt generation due to Ownership Change.
29:7
304
Reserved. Read/Write 0s.
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - USB Controller Registers - PCIUSB
Revision 5.1
Table 6-42. USB_BAR+Memory Offset: USB Controller Registers (Continued)
Bit
6
Description
RootHubStatusChangeEnable.
0: Ignore.
1: Disable interrupt generation due to Root Hub Status Change.
5
FrameNumberOverflowEnable.
0: Ignore.
1: Disable interrupt generation due to Frame Number Overflow.
4
UnrecoverableErrorEnable. This event is not implemented. All writes to this bit will be ignored.
3
ResumeDetectedEnable.
0: Ignore.
1: Disable interrupt generation due to Resume Detected.
2
StartOfFrameEnable.
0: Ignore.
1: Disable interrupt generation due to Start of Frame.
1
WritebackDoneHeadEnable.
0: Ignore.
1: Disable interrupt generation due to Writeback Done Head.
0
SchedulingOverrunEnable.
0: Ignore.
1: Disable interrupt generation due to Scheduling Overrun.
Note:
Writing a 1 to a bit in this register clears the corresponding bit, while writing a 0 to a bit leaves the bit unchanged.
Offset 18h-1Bh
HcHCCA Register (R/W)
Reset Value = 00000000h
HcPeriodCurrentED Register (R/W)
Reset Value = 00000000h
31:8
HCCA. Pointer to HCCA base address.
7:0
Reserved. Read/Write 0s.
Offset 1Ch-1Fh
31:4
PeriodCurrentED. Pointer to the current Periodic List ED.
3:0
Reserved. Read/Write 0s.
Offset 20h-23h
HcControlHeadED Register (R/W)
31:4
ControlHeadED. Pointer to the Control List Head ED.
3:0
Reserved. Read/Write 0s.
Offset 24h-27h
HcControlCurrentED Register (R/W)
31:4
ControlCurrentED. Pointer to the current Control List ED.
3:0
Reserved. Read/Write 0s.
Offset 28h-2Bh
HcBulkHeadED Register (R/W)
31:4
BulkHeadED. Pointer to the Bulk List Head ED.
3:0
Reserved. Read/Write 0s.
Offset 2Ch-2Fh
HcBulkCurrentED Register (R/W)
31:4
BulkCurrentED. Pointer to the current Bulk List ED.
3:0
Reserved. Read/Write 0s.
Offset 30h-33h
HcDoneHead Register (R/W)
31:4
DoneHead. Pointer to the current Done List Head ED.
3:0
Reserved. Read/Write 0s.
AMD Geode™ SC3200 Processor Data Book
Reset Value = 00000000h
Reset Value = 00000000h
Reset Value = 00000000h
Reset Value = 00000000h
Reset Value = 00000000h
305
Revision 5.1
Core Logic Module - USB Controller Registers - PCIUSB
Table 6-42. USB_BAR+Memory Offset: USB Controller Registers (Continued)
Bit
Description
Offset 34h-37h
31
HcFmInterval Register (R/W)
Reset Value = 00002EDFh
FrameIntervalToggle (Read Only). This bit is toggled by HCD when it loads a new value into FrameInterval.
30:16
FSLargestDataPacket (Read Only). This field specifies a value which is loaded into the Largest Data Packet Counter at
the beginning of each frame.
15:14
Reserved. Read/Write 0s.
13:0
FrameInterval. This field specifies the length of a frame as (bit times - 1). For 12,000 bit times in a frame, a value of 11,999
is stored here.
Offset 38h-3Bh
31
HcFrameRemaining Register (RO)
Reset Value = 00000000h
FrameRemainingToggle (Read Only). Loaded with FrameIntervalToggle when FrameRemaining is loaded.
30:14
Reserved. Read 0s.
13:0
FrameRemaining (Read Only). When the HC is in the UsbOperational state, this 14-bit field decrements each 12 MHz
clock period. When the count reaches 0, (end of frame) the counter reloads with FrameInterval. In addition, the counter
loads when the HC transitions into UsbOperational.
Offset 3Ch-3Fh
HcFmNumber Register (RO)
Reset Value = 00000000h
31:16
Reserved. Read 0s.
15:0
FrameNumber (Read Only). This 16-bit incrementing counter field is incremented coincident with the loading of FrameRemaining. The count rolls over from FFFFh to 0h.
Offset 40h-43h
HcPeriodicStart Register (R/W)
Reset Value = 00000000h
31:14
Reserved. Read/Write 0s.
13:0
PeriodicStart. This field contains a value used by the List Processor to determine where in a frame the Periodic List processing must begin.
Offset 44h-47h
HcLSThreshold Register (R/W)
Reset Value = 00000628h
31:12
Reserved. Read/Write 0s.
11:0
LSThreshold. This field contains a value used by the Frame Management block to determine whether or not a low speed
transaction can be started in the current frame.
Offset 48h-4Bh
HcRhDescriptorA Register (R/W)
Reset Value = 01000003h
31:24
PowerOnToPowerGoodTime. This field value is represented as the number of 2 ms intervals, ensuring that the power
switching is effective within 2 ms. Only bits [25:24] are implemented as R/W. The remaining bits are read only as 0. It is not
expected that these bits be written to anything other than 1h, but limited adjustment is provided. This field should be written
to support system implementation. This field should always be written to a non-zero value.
23:13
Reserved. Read/Write 0s.
12
NoOverCurrentProtection. This bit should be written to support the external system port over-current implementation.
0: Over-current status is reported.
1: Over-current status is not reported.
11
OverCurrentProtectionMode. This bit should be written 0 and is only valid when NoOverCurrentProtection is cleared.
0: Global Over-Current.
1: Individual Over-Current
10
9
DeviceType (Read Only). USB is not a compound device.
NoPowerSwitching. This bit should be written to support the external system port power switching implementation.
0: Ports are power switched.
1: Ports are always powered on.
8
PowerSwitchingMode. This bit is only valid when NoPowerSwitching is cleared. This bit should be written 0.
0: Global Switching.
1: Individual Switching
306
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - USB Controller Registers - PCIUSB
Revision 5.1
Table 6-42. USB_BAR+Memory Offset: USB Controller Registers (Continued)
Bit
Description
7:0
NumberDownstreamPorts (Read Only). USB supports three downstream ports.
Note:
This register is only reset by a power-on reset (PCIRST#). It is written during system initialization to configure the Root Hub.
These bit should not be written during normal operation.
Offset 4Ch-4Fh
31:16
HcRhDescriptorB Register (R/W)
Reset Value = 00000000h
PortPowerControlMask. Global-power switching. This field is only valid if NoPowerSwitching is cleared and PowerSwitchingMode is set (individual port switching). When set, the port only responds to individual port power switching commands (Set/ClearPortPower). When cleared, the port only responds to global power switching commands (Set/
ClearGlobalPower).
0: Device not removable.
1: Global-power mask.
Port Bit relationship - Unimplemented ports are reserved, read/write 0.
0 = Reserved
1 = Port 1
2 = Port 2
...
15 = Port 15
15:0
DeviceRemoveable. USB ports default to removable devices.
0: Device not removable.
1: Device removable.
Port Bit relationship
0 = Reserved
1 = Port 1
2 = Port 2
...
15 = Port 15
Unimplemented ports are reserved, read/write 0.
Note:
This register is only reset by a power-on reset (PCIRST#). It is written during system initialization to configure the Root Hub.
These bit should not be written during normal operation.
Offset 50h-53h
31
30:18
HcRhStatus Register (R/W)
Reset Value = 00000000h
ClearRemoteWakeupEnable (Write Only). Writing a 1 to this bit clears DeviceRemoteWakeupEnable. Writing a 0 has no
effect.
Reserved. Read/Write 0s.
17
OverCurrentIndicatorChange. This bit is set when OverCurrentIndicator changes. Writing a 1 clears this bit. Writing a 0
has no effect.
16
Read: LocalPowerStatusChange. Not supported. Always read 0.
Write: SetGlobalPower. Write a 1 issues a SetGlobalPower command to the ports. Writing a 0 has no effect.
15
Read: DeviceRemoteWakeupEnable. This bit enables ports' ConnectStatusChange as a remote wakeup event.
0: Disabled.
1: Enabled.
Write: SetRemoteWakeupEnable. Writing a 1 sets DeviceRemoteWakeupEnable. Writing a 0 has no effect.
14:2
1
Reserved. Read/Write 0s.
OverCurrentIndicator. This bit reflects the state of the OVRCUR pin. This field is only valid if NoOverCurrentProtection
and OverCurrentProtectionMode are cleared.
0: No over-current condition.
1:Over-current condition.
0
Read: LocalPowerStatus. Not Supported. Always read 0.
Write: ClearGlobalPower. Writing a 1 issues a ClearGlobalPower command to the ports. Writing a 0 has no effect.
Note:
This register is reset by the UsbReset state.
AMD Geode™ SC3200 Processor Data Book
307
Revision 5.1
Core Logic Module - USB Controller Registers - PCIUSB
Table 6-42. USB_BAR+Memory Offset: USB Controller Registers (Continued)
Bit
Description
Offset 54h-57h
31:21
20
HcRhPortStatus[1] Register (R/W)
Reset Value = 00000000h
Reserved. Read/Write 0s.
PortResetStatusChange. This bit indicates that the port reset signal has completed.
0: Port reset is not complete.
1: Port reset is complete.
19
PortOverCurrentIndicatorChange. This bit is set when OverCurrentIndicator changes. Writing a 1 clears this bit. Writing
a 0 has no effect.
18
PortSuspendStatusChange. This bit indicates the completion of the selective resume sequence for the port.
0: Port is not resumed.
1: Port resume is complete.
17
PortEnableStatusChange. This bit indicates that the port has been disabled due to a hardware event (cleared PortEnableStatus).
0: Port has not been disabled.
1: PortEnableStatus has been cleared.
16
ConnectStatusChange. This bit indicates a connect or disconnect event has been detected. Writing a 1 clears this bit.
Writing a 0 has no effect.
0: No connect/disconnect event.
1: Hardware detection of connect/disconnect event.
If DeviceRemoveable is set, this bit resets to 1.
15:10
9
Reserved. Read/Write 0s.
Read: LowSpeedDeviceAttached. This bit defines the speed (and bud idle) of the attached device. It is only valid when
CurrentConnectStatus is set.
0: Full Speed device.
1: Low Speed device.
Write: ClearPortPower. Writing a 1 clears PortPowerStatus. Writing a 0 has no effect.
8
Read: PortPowerStatus. This bit reflects the power state of the port regardless of the power switching mode.
0: Port power is off.
1: Port power is on.
If NoPowerSwitching is set, this bit is always read as 1.
Write: SetPortPower. Writing a 1 sets PortPowerStatus. Writing a 0 has no effect.
7:5
4
Reserved. Read/Write 0s.
Read: PortResetStatus.
0: Port reset signal is not active.
1: Port reset signal is active.
Write: SetPortReset. Writing a 1 sets PortResetStatus. Writing a 0 has no effect.
3
Read: PortOverCurrentIndicator. This bit reflects the state of the OVRCUR pin dedicated to this port. This field is only
valid if NoOverCurrentProtection is cleared and OverCurrentProtectionMode is set.
0: No over-current condition.
1: Over-current condition.
Write: ClearPortSuspend. Writing a 1 initiates the selective resume sequence for the port. Writing a 0 has no effect.
2
Read: PortSuspendStatus.
0: Port is not suspended.
1: Port is selectively suspended.
Write: SetPortSuspend. Writing a 1 sets PortSuspendStatus. Writing a 0 has no effect.
308
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - USB Controller Registers - PCIUSB
Revision 5.1
Table 6-42. USB_BAR+Memory Offset: USB Controller Registers (Continued)
Bit
1
Description
Read: PortEnableStatus.
0: Port disabled.
1: Port enabled.
Write: SetPortEnable. Writing a 1 sets PortEnableStatus. Writing a 0 has no effect.
0
Read: CurrentConnectStatus.
0: No device connected.
1: Device connected.
If DeviceRemoveable is set (not removable) this bit is always 1.
Write: ClearPortEnable. Writing 1 a clears PortEnableStatus. Writing a 0 has no effect.
Note:
This register is reset by the UsbReset state.
Offset 58h-5Bh
31:21
20
HcRhPortStatus[2] Register (R/W)
Reset Value = 00000000h
Reserved. Read/Write 0s.
PortResetStatusChange. This bit indicates that the port reset signal has completed.
0: Port reset is not complete.
1: Port reset is complete.
19
PortOverCurrentIndicatorChange. This bit is set when OverCurrentIndicator changes. Writing a 1 clears this bit. Writing
a 0 has no effect.
18
PortSuspendStatusChange. This bit indicates the completion of the selective resume sequence for the port.
0: Port is not resumed.
1: Port resume is complete.
17
PortEnableStatusChange. This bit indicates that the port has been disabled due to a hardware event (cleared PortEnableStatus).
0: Port has not been disabled.
1: PortEnableStatus has been cleared.
16
ConnectStatusChange. This bit indicates a connect or disconnect event has been detected. Writing a 1 clears this bit.
Writing a 0 has no effect.
0: No connect/disconnect event.
1: Hardware detection of connect/disconnect event.
If DeviceRemoveable is set, this bit resets to 1.
15:10
9
Reserved. Read/Write 0s.
Read: LowSpeedDeviceAttached. This bit defines the speed (and bud idle) of the attached device. It is only valid when
CurrentConnectStatus is set.
0: Full speed device.
1: Low speed device.
Write: ClearPortPower. Writing a 1 clears PortPowerStatus. Writing a 0 has no effect.
8
Read: PortPowerStatus. This bit reflects the power state of the port regardless of the power switching mode.
0: Port power is off.
1: Port power is on.
If NoPowerSwitching is set, this bit is always read as 1.
Write: SetPortPower. Writing a 1 sets PortPowerStatus. Writing a 0 has no effect.
7:5
Reserved. Read/Write 0s.
4
Read: PortResetStatus.
0: Port reset signal is not active.
1: Port reset signal is active.
Write: SetPortReset. Writing a 1 sets PortResetStatus. Writing a 0 has no effect.
AMD Geode™ SC3200 Processor Data Book
309
Revision 5.1
Core Logic Module - USB Controller Registers - PCIUSB
Table 6-42. USB_BAR+Memory Offset: USB Controller Registers (Continued)
Bit
3
Description
Read: PortOverCurrentIndicator. This bit reflects the state of the OVRCUR pin dedicated to this port. This field is only
valid if NoOverCurrentProtection is cleared and OverCurrentProtectionMode is set.
0: No over-current condition.
1: Over-current condition.
Write: ClearPortSuspend. Writing a 1 initiates the selective resume sequence for the port. Writing a 0 has no effect.
2
Read: PortSuspendStatus.
0: Port is not suspended.
1: Port is selectively suspended.
Write: SetPortSuspend. Writing a 1 sets PortSuspendStatus. Writing a 0 has no effect.
1
Read: PortEnableStatus.
0: Port disabled.
1: Port enabled.
Write: SetPortEnable. Writing a 1 sets PortEnableStatus. Writing a 0 has no effect.
0
Read: CurrentConnectStatus.
0: No device connected.
1: Device connected.
If DeviceRemoveable is set (not removable) this bit is always 1.
Write: ClearPortEnable. Writing 1 a clears PortEnableStatus. Writing a 0 has no effect.
Note:
This register is reset by the UsbReset state.
Offset 5Ch-5Fh
31:21
20
HcRhPortStatus[3] Register (R/W)
Reset Value = 00000000h
Reserved. Read/Write 0s.
PortResetStatusChange. This bit indicates that the port reset signal has completed.
0: Port reset is not complete.
1: Port reset is complete.
19
18
PortOverCurrentIndicatorChange. This bit is set when OverCurrentIndicator changes. Writing a 1 clears this bit. Writing
a 0 has no effect.
PortSuspendStatusChange. This bit indicates the completion of the selective resume sequence for the port.
0: Port is not resumed.
1: Port resume is complete.
17
PortEnableStatusChange. This bit indicates that the port has been disabled due to a hardware event (cleared PortEnableStatus).
0: Port has not been disabled.
1: PortEnableStatus has been cleared.
16
ConnectStatusChange. This bit indicates a connect or disconnect event has been detected. Writing a 1 clears this bit.
Writing a 0 has no effect.
0: No connect/disconnect event.
1: Hardware detection of connect/disconnect event.
If DeviceRemoveable is set, this bit resets to 1.
15:10
9
Reserved. Read/Write 0s.
Read: LowSpeedDeviceAttached. This bit defines the speed (and bud idle) of the attached device. It is only valid when
CurrentConnectStatus is set.
0: Full speed device.
1: Low speed device.
Write: ClearPortPower. Writing a 1 clears PortPowerStatus. Writing a 0 has no effect.
310
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module - USB Controller Registers - PCIUSB
Table 6-42. USB_BAR+Memory Offset: USB Controller Registers (Continued)
Bit
8
Description
Read: PortPowerStatus. This bit reflects the power state of the port regardless of the power switching mode.
0: Port power is off.
1: Port power is on.
If NoPowerSwitching is set, this bit is always read as 1.
Write: SetPortPower. Writing a 1 sets PortPowerStatus. Writing a 0 has no effect.
7:5
Reserved. Read/Write 0s.
4
Read: PortResetStatus.
0: Port reset signal is not active.
1: Port reset signal is active.
Write: SetPortReset. Writing a 1 sets PortResetStatus. Writing a 0 has no effect.
3
Read: PortOverCurrentIndicator. This bit reflects the state of the OVRCUR pin dedicated to this port. This field is only
valid if NoOverCurrentProtection is cleared and OverCurrentProtectionMode is set.
0: No over-current condition.
1: Over-current condition.
Write: ClearPortSuspend. Writing a 1 initiates the selective resume sequence for the port. Writing a 0 has no effect.
2
Read: PortSuspendStatus.
0: Port is not suspended.
1: Port is selectively suspended.
Write: SetPortSuspend. Writing a 1 sets PortSuspendStatus. Writing a 0 has no effect.
1
Read: PortEnableStatus.
0: Port disabled.
1: Port enabled.
Write: SetPortEnable. Writing a 1 sets PortEnableStatus. Writing a 0 has no effect.
0
Read: CurrentConnectStatus.
0: No device connected.
1: Device connected.
If DeviceRemoveable is set (not removable) this bit is always 1.
Write: ClearPortEnable. Writing 1 a clears PortEnableStatus. Writing a 0 has no effect.
Note:
This register is reset by the UsbReset state.
Offset 60h-9Fh
Offset 100h-103h
31:9
Reserved
HceControl Register (R/W)
Reset Value = xxh
Reset Value = 00000000h
Reserved. Read/Write 0s.
8
A20State. Indicates current state of Gate A20 on keyboard controller. Compared against value written to 60h when
GateA20Sequence is active.
7
IRQ12Active. Indicates a positive transition on IRQ12 from keyboard controller occurred. Software writes this bit to 1 to
clear it (set it to 0); a 0 write has no effect.
6
IRQ1Active. Indicates a positive transition on IRQ1 from keyboard controller occurred. Software writes this bit to 1 to clear
it (set it to 0); a 0 write has no effect.
5
GateA20Sequence. Set by HC when a data value of D1h is written to I/O port 64h. Cleared by HC on write to I/O port 64h
of any value other than D1h.
4
ExternalIRQEn. When set to 1, IRQ1 and IRQ12 from the keyboard controller cause an emulation interrupt. The function
controlled by this bit is independent of the setting of the EmulationEnable bit in this register.
3
IRQEn. When set, the HC generates IRQ1 or IRQ12 as long as the OutputFull bit in HceStatus is set to 1. If the AuxOutputFull bit of HceStatus is 0, IRQ1 is generated: if 1, then an IRQ12 is generated.
2
CharacterPending. When set, an emulation interrupt will be generated when the OutputFull bit of the HceStatus register is
set to 0.
AMD Geode™ SC3200 Processor Data Book
311
Revision 5.1
Core Logic Module - USB Controller Registers - PCIUSB
Table 6-42. USB_BAR+Memory Offset: USB Controller Registers (Continued)
Bit
Description
1
EmulationInterrupt (Read Only). This bit is a static decode of the emulation interrupt condition.
0
EmulationEnable. When set to 1 the HC is enabled for legacy emulation and will decode accesses to I/O registers 60h
and 64h and generate IRQ1 and/or IRQ12 when appropriate. The HC also generates an emulation interrupt at appropriate
times to invoke the emulation software.
Note:
This register is used to enable and control the emulation hardware and report various status information.
Offset 104h-107h
31:8
7:0
Note:
7:0
Note:
InputData. This register holds data written to I/O ports 60h and 64h.
This register is the emulation side of the legacy Input Buffer register.
Reset Value = 000000xxh
OutputData. This register hosts data that is returned when an I/O read of port 60h is performed by application software.
This register is the emulation side of the legacy Output Buffer register where keyboard and mouse data is to be written by software.
HceStatus Register (R/W)
Reset Value = 00000000h
Reserved. Read/Write 0s.
7
Parity. Indicates parity error on keyboard/mouse data.
6
Timeout. Used to indicate a time-out
5
AuxOutputFull. IRQ12 is asserted whenever this bit is set to 1 and OutputFull is set to 1 and the IRQEn bit is set.
4
Inhibit Switch. This bit reflects the state of the keyboard inhibit switch and is set if the keyboard is NOT inhibited.
3
CmdData. The HC will set this bit to 0 on an I/O write to port 60h and on an I/O write to port 64h the HC will set this bit to 1.
2
Flag. Nominally used as a system flag by software to indicate a warm or cold boot.
1
InputFull. Except for the case of a Gate A20 sequence, this bit is set to 1 on an I/O write to address 60h or 64h. While this
bit is set to 1 and emulation is enabled, an emulation interrupt condition exists.
0
OutputFull. The HC will set this bit to 0 on a read of I/O port 60h. If IRQEn is set and AuxOutputFull is set to 0 then an
IRQ1 is generated as long as this bit is set to 1. If IRQEn is set and AuxOutputFull is set to 1 then and IRQ12 will be generated a long as this bit is set to 1. While this bit is 0 and CharacterPending in HceControl is set to 1, an emulation interrupt condition exists.
Note:
312
HceOutput Register (R/W)
Reserved. Read/Write 0s.
Offset 10Ch-10Fh
31:8
Reset Value = 000000xxh
Reserved. Read/Write 0s.
Offset 108h-10Bh
31:8
HceInput Register (R/W)
This register is the emulation side of the legacy Status register.
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module - ISA Legacy Register Space
6.4.7
ISA Legacy Register Space
The ISA Legacy registers reside in the ISA I/O address
space in the address range from 000h to FFFh and are
accessed through typical input/output instructions (i.e.,
CPU direct R/W) with the designated I/O port address and
8-bit data.
• DMA Page Registers, see Table 6-44
The bit formats for the ISA Legacy I/O Registers plus two
chipset-specific configuration registers used for interrupt
mapping in the Core Logic module are given in this section.
The ISA Legacy registers are separated into the following
DMA Channel Control Registers, see Table 6-43
• Keyboard Controller Registers, see Table 6-47
• Programmable Interval Timer Registers, see Table 6-45
• Programmable Interrupt Controller Registers, see Table
6-46
• Real-Time Clock Registers, see Table 6-48
• Miscellaneous Registers, see Table 6-49 (includes
4D0h and 4D1h Interrupt Edge/Level Select Registers)
Table 6-43. DMA Channel Control Registers
Bit
Description
I/O Port 000h
DMA Channel 0 Address Register (R/W)
Written as two successive bytes, byte 0, 1.
I/O Port 001h
DMA Channel 0 Transfer Count Register (R/W)
Written as two successive bytes, byte 0, 1.
I/O Port 002h
DMA Channel 1 Address Register (R/W)
Written as two successive bytes, byte 0, 1.
I/O Port 003h
DMA Channel 1 Transfer Count Register (R/W)
Written as two successive bytes, byte 0, 1.
I/O Port 004h
DMA Channel 2 Address Register (R/W)
Written as two successive bytes, byte 0, 1.
I/O Port 005h
DMA Channel 2 Transfer Count Register (R/W)
Written as two successive bytes, byte 0, 1.
I/O Port 006h
DMA Channel 3 Address Register (R/W)
Written as two successive bytes, byte 0, 1.
I/O Port 007h
DMA Channel 3 Transfer Count Register (R/W)
Written as two successive bytes, byte 0, 1.
I/O Port 008h (R/W)
Read
7
DMA Status Register, Channels 3:0
Channel 3 Request. Indicates if a request is pending.
0: No.
1: Yes.
6
Channel 2 Request. Indicates if a request is pending.
0: No.
1: Yes.
5
Channel 1 Request. Indicates if a request is pending.
0: No.
1: Yes.
4
Channel 0 Request. Indicates if a request is pending.
0: No.
1: Yes.
3
Channel 3 Terminal Count. Indicates if TC was reached.
0: No.
1: Yes.
AMD Geode™ SC3200 Processor Data Book
313
Revision 5.1
Core Logic Module - ISA Legacy Register Space
Table 6-43. DMA Channel Control Registers (Continued)
Bit
2
Description
Channel 2 Terminal Count. Indicates if TC was reached.
0: No.
1: Yes.
1
Channel 1 Terminal Count. Indicates if TC was reached.
0: No.
1: Yes.
0
Channel 0 Terminal Count. Indicates if TC was reached.
0: No.
1: Yes.
Write
7
DMA Command Register, Channels 3:0
DACK Sense.
0: Active low.
1: Active high.
6
DREQ Sense.
0: Active high.
1: Active low.
5
Write Selection.
0: Late write.
1: Extended write.
4
Priority Mode.
0: Fixed.
1: Rotating.
3
Timing Mode.
0: Normal.
1: Compressed.
2
Channels 3:0.
0: Disable.
1: Enable.
1:0
Reserved. Must be set to 0.
I/O Port 009h
7:3
2
Software DMA Request Register, Channels 3:0 (W)
Reserved. Must be set to 0.
Request Type.
0: Reset.
1: Set.
1:0
Channel Number Request Select
00:
01:
10:
11:
Channel 0.
Channel 1.
Channel 2.
Channel 3.
I/O Port 00Ah
7:3
2
DMA Channel Mask Register, Channels 3:0 (WO)
Reserved. Must be set to 0.
Channel Mask.
0: Not masked.
1: Masked.
1:0
Channel Number Mask Select.
00:
01:
10:
11:
314
Channel 0.
Channel 1.
Channel 2.
Channel 3.
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - ISA Legacy Register Space
Revision 5.1
Table 6-43. DMA Channel Control Registers (Continued)
Bit
Description
I/O Port 00Bh
7:6
00:
01:
10:
11:
5
DMA Channel Mode Register, Channels 3:0 (WO)
Transfer Mode.
Demand.
Single.
Block.
Cascade.
Address Direction.
0: Increment.
1: Decrement.
4
Auto-initialize.
0: Disable.
1: Enable.
3:2
Transfer Type.
00:
01:
10:
11:
1:0
Verify.
Write transfer (I/O to memory).
Read transfer (memory to I/O).
Reserved.
Channel Number Mode Select.
00:
01:
10:
11:
Channel 0.
Channel 1.
Channel 2.
Channel 3.
I/O Port 00Ch
DMA Clear Byte Pointer Command, Channels 3:0 (W)
I/O Port 00Dh
DMA Master Clear Command, Channels 3:0 (W)
I/O Port 00Eh
DMA Clear Mask Register Command, Channels 3:0 (W)
I/O Port 00Fh
DMA Write Mask Register Command, Channels 3:0 (W)
I/O Port 0C0h
DMA Channel 4 Address Register (R/W)
Not used.
I/O Port 0C2h
DMA Channel 4 Transfer Count Register (R/W)
Not used.
I/O Port 0C4h
DMA Channel 5 Address Register (R/W)
Not supported.
I/O Port 0C6h
DMA Channel 5 Transfer Count Register (R/W)
Not supported.
I/O Port 0C8h
DMA Channel 6 Address Register (R/W)
Not supported.
I/O Port 0CAh
DMA Channel 6 Transfer Count Register (R/W)
Not supported.
I/O Port 0CCh
DMA Channel 7 Address Register (R/W)
Not supported.
I/O Port 0CEh
DMA Channel 7 Transfer Count Register (R/W)
Not supported.
AMD Geode™ SC3200 Processor Data Book
315
Revision 5.1
Core Logic Module - ISA Legacy Register Space
Table 6-43. DMA Channel Control Registers (Continued)
Bit
Description
I/O Port 0D0h (R/W)
Read
Note:
7
DMA Status Register, Channels 7:4
Channels 5, 6, and 7 are not supported.
Channel 7 Request. Indicates if a request is pending.
0: No.
1: Yes.
6
Channel 6 Request. Indicates if a request is pending.
0: No.
1: Yes.
5
Channel 5 Request. Indicates if a request is pending.
0: No.
1: Yes.
4
Undefined.
3
Channel 7 Terminal Count. Indicates if TC was reached.
0: No.
1: Yes.
2
Channel 6 Terminal Count. Indicates if TC was reached.
0: No.
1: Yes.
1
Channel 5 Terminal Count. Indicates if TC was reached.
0: No.
1: Yes.
0
Undefined.
Write
Note:
7
DMA Command Register, Channels 7:4
Channels 5, 6, and 7 are not supported.
DACK Sense.
0: Active low.
1: Active high.
6
DREQ Sense.
0: Active high.
1: Active low.
5
Write Selection.
0: Late write.
1: Extended write.
4
Priority Mode.
0: Fixed.
1: Rotating.
3
Timing Mode.
0: Normal.
1: Compressed.
2
Channels 7:4.
0: Disable.
1: Enable.
1:0
316
Reserved. Must be set to 0.
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - ISA Legacy Register Space
Revision 5.1
Table 6-43. DMA Channel Control Registers (Continued)
Bit
Description
I/O Port 0D2h
Note:
7:3
2
Software DMA Request Register, Channels 7:4 (W)
Channels 5, 6, and 7 are not supported.
Reserved. Must be set to 0.
Request Type.
0: Reset.
1: Set.
1:0
Channel Number Request Select.
00:
01:
10:
11:
Illegal.
Channel 5.
Channel 6.
Channel 7.
I/O Port 0D4h
Note:
7:3
2
DMA Channel Mask Register, Channels 7:4 (WO)
Channels 5, 6, and 7 are not supported.
Reserved. Must be set to 0.
Channel Mask.
0: Not masked.
1: Masked.
1:0
Channel Number Mask Select.
00:
01:
10:
11:
Channel 4.
Channel 5.
Channel 6.
Channel 7.
I/O Port 0D6h
Note:
7:6
Transfer Mode.
00:
01:
10:
11:
5
DMA Channel Mode Register, Channels 7:4 (WO)
Channels 5, 6, and 7 are not supported.
Demand.
Single.
Block.
Cascade.
Address Direction.
0: Increment.
1: Decrement.
4
Auto-initialize.
0: Disabled
1: Enable
3:2
Transfer Type.
00:
01:
10:
11:
1:0
Verify.
Write transfer (I/O to memory).
Read transfer (memory to I/O).
Reserved.
Channel Number Mode Select.
00: Channel 4.
01: Channel 5.
10: Channel 6.
11: Channel 7.
Channel 4 must be programmed in cascade mode. This mode is not the default.
I/O Port 0D8h
Note:
I/O Port 0DAh
Note:
DMA Master Clear Command, Channels 7:4 (W)
Channels 5, 6, and 7 are not supported.
I/O Port 0DCh
Note:
DMA Clear Byte Pointer Command, Channels 7:4 (W)
Channels 5, 6, and 7 are not supported.
DMA Clear Mask Register Command, Channels 7:4 (W)
Channels 5, 6, and 7 are not supported.
AMD Geode™ SC3200 Processor Data Book
317
Revision 5.1
Core Logic Module - ISA Legacy Register Space
Table 6-43. DMA Channel Control Registers (Continued)
Bit
Description
I/O Port 0DEh
Note:
DMA Write Mask Register Command, Channels 7:4 (W)
Channels 5, 6, and 7 are not supported.
Table 6-44. DMA Page Registers
Bit
Description
I/O Port 081h
DMA Channel 2 Low Page Register (R/W)
Address bits [23:16] (byte 2).
I/O Port 082h
DMA Channel 3 Low Page Register (R/W)
Address bits [23:16] (byte 2).
I/O Port 083h
DMA Channel 1 Low Page Register (R/W)
Address bits [23:16] (byte 2).
I/O Port 087h
DMA Channel 0 Low Page Register (R/W)
Address bits [23:16] (byte 2).
I/O Port 089h
DMA Channel 6 Low Page Register (R/W)
Nor supported.
I/O Port 08Ah
DMA Channel 7 Low Page Register (R/W)
Not supported.
I/O Port 08Bh
DMA Channel 5 Low Page Register (R/W)
Not supported.
I/O Port 08Fh
ISA Refresh Low Page Register (R/W)
Refresh address.
I/O Port 481h
DMA Channel 2 High Page Register (R/W)
Address bits [31:24] (byte 3).
Note:
This register is reset to 00h on any access to Port 081h.
I/O Port 482h
DMA Channel 3 High Page Register (R/W)
Address bits [31:24] (byte 3).
Note:
This register is reset to 00h on any access to Port 082h.
I/O Port 483h
DMA Channel 1 High Page Register (R/W)
Address bits [31:24] (byte 3).
Note:
This register is reset to 00h on any access to Port 083h.
I/O Port 487h
DMA Channel 0 High Page Register (R/W)
Address bits [31:24] (byte 3).
Note:
This register is reset to 00h on any access to Port 087h.
I/O Port 489h
DMA Channel 6 High Page Register (R/W)
Not supported
I/O Port 48Ah
DMA Channel 7 High Page Register (R/W)
Not spported
I/O Port 48Bh
DMA Channel 5 High Page Register (R/W)
Not supported
318
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module - ISA Legacy Register Space
Table 6-45. Programmable Interval Timer Registers
Bit
Description
I/O Port 040h
Write
7:0
PIT Timer 0 Counter
Counter Value.
Read
PIT Timer 0 Status
7
Counter Output. State of counter output signal.
6
Counter Loaded. Indicates if the last count written is loaded.
0: Yes.
1: No.
5:4
Current Read/Write Mode.
00:
01:
10:
11:
3:1
0
Counter latch command.
R/W LSB only.
R/W MSB only.
R/W LSB, followed by MSB.
Current Counter Mode. 0-5.
BCD Mode.
0: Binary.
1: BCD (Binary Coded Decimal).
I/O Port 041h
Write
7:0
PIT Timer 1 Counter (Refresh)
Counter Value.
Read
PIT Timer 1 Status (Refresh)
7
Counter Output. State of counter output signal.
6
Counter Loaded. Indicates if the last count written is loaded.
0: Yes.
1: No.
5:4
Current Read/Write Mode.
00:
01:
10:
11:
3:1
0
Counter latch command.
R/W LSB only.
R/W MSB only.
R/W LSB, followed by MSB.
Current Counter Mode. 0-5.
BCD Mode.
0: Binary.
1: BCD (Binary Coded Decimal).
AMD Geode™ SC3200 Processor Data Book
319
Revision 5.1
Core Logic Module - ISA Legacy Register Space
Table 6-45. Programmable Interval Timer Registers (Continued)
Bit
Description
I/O Port 042h
Write
7:0
PIT Timer 2 Counter (Speaker)
Counter Value.
Read
PIT Timer 2 Status (Speaker)
7
Counter Output. State of counter output signal.
6
Counter Loaded. Indicates if the last count written is loaded.
0: Yes.
1: No.
5:4
Current Read/Write Mode.
00:
01:
10:
11:
3:1
0
Counter latch command.
R/W LSB only.
R/W MSB only.
R/W LSB, followed by MSB.
Current Counter Mode. 0-5.
BCD Mode.
0: Binary.
1: BCD (Binary Coded Decimal).
I/O Port 043h (R/W)
PIT Mode Control Word Register
Notes: 1. If bits [7:6] = 11: Register functions as Read Status Command and:
Bit 5 = Latch Count
Bit 4 = Latch Status
Bit 3 = Select Counter 2
Bit 2 = Select Counter 1
Bit 1 = Select Counter 0
Bit 0 = Reserved
2. If bits [5:4] = 00: Register functions as Counter Latch Command and:
Bits [7:6] = Selects Counter
Bits [3:0] = Don’t care
7:6
Counter Select.
00:
01:
10:
11:
5:4
Current Read/Write Mode.
00:
01:
10:
11:
3:1
0
Counter 0.
Counter 1.
Counter 2.
Read-back command (Note 1).
Counter latch command.
R/W LSB only.
R/W MSB only.
R/W LSB, followed by MSB.
Current Counter Mode. 0-5.
BCD Mode.
0: Binary.
1: BCD (Binary Coded Decimal).
320
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - ISA Legacy Register Space
Revision 5.1
Table 6-46. Programmable Interrupt Controller Registers
Bit
Description
I/O Port 020h / 0A0h
Master / Slave PIC ICW1 (WO)
7:5
Reserved. Must be set to 0.
4
Reserved. Must be set to 1.
3
Trigger Mode.
0: Edge.
1: Level.
2
Vector Address Interval
0: 8 byte intervals.
1: 4 byte intervals.
1
Reserved. Must be set to 0 (cascade mode).
0
Reserved. Must be set to 1 (ICW4 must be programmed).
I/O Port 021h / 0A1h
Master / Slave PIC ICW2 (after ICW1 is written) (WO)
7:3
A[7:3]. Address lines [7:3] for base vector for interrupt controller.
2:0
Reserved. Must be set to 0.
I/O Port 021h / 0A1h
Master / Slave PIC ICW3 (after ICW2 is written) (WO)
Master PIC ICW3
7:0
Cascade IRQ. Must be 04h.
Slave PIC ICW3
7:0
Slave ID. Must be 02h.
I/O Port 021h / 0A1h
Master / Slave PIC ICW4 (after ICW3 is written) (WO)
7:5
Reserved. Must be set to 0.
4
Special Fully Nested Mode.
0: Disable.
1: Enable.
3:2
1
Reserved. Must be set to 0.
Auto EOI.
0: Normal EOI.
1: Auto EOI.
0
Reserved. Must be set to 1 (8086/8088 mode).
I/O Port 021h / 0A1h (R/W)
7
Master / Slave PIC OCW1
(except immediately after ICW1 is written)
IRQ7 / IRQ15 Mask.
0: Not Masked.
1: Mask.
6
IRQ6 / IRQ14 Mask.
0: Not Masked.
1: Mask.
5
IRQ5 / IRQ13 Mask.
0: Not Masked.
1: Mask.
4
IRQ4 / IRQ12 Mask.
0: Not Masked.
1: Mask.
3
IRQ3 / IRQ11 Mask.
0: Not Masked.
1: Mask.
AMD Geode™ SC3200 Processor Data Book
321
Revision 5.1
Core Logic Module - ISA Legacy Register Space
Table 6-46. Programmable Interrupt Controller Registers (Continued)
Bit
2
Description
IRQ2 / IRQ10 Mask.
0: Not Masked.
1: Mask.
1
IRQ1 / IRQ9 Mask.
0: Not Masked.
1: Mask.
0
IRQ0 / IRQ8 Mask.
0: Not Masked.
1: Mask.
I/O Port 020h / 0A0h
7:5
Master / Slave PIC OCW2 (WO)
Rotate/EOI Codes.
000: Clear rotate in Auto EOI mode
001: Non-specific EOI
010: No operation
011: Specific EOI (bits [2:0] must be valid)
4:3
Reserved. Must be set to 0.
2:0
IRQ Number (000-111).
I/O Port 020h / 0A0h
7
6:5
100: Set rotate in Auto EOI mode
101: Rotate on non-specific EOI command
110: Set priority command (bits [2:0] must be valid)
111: Rotate on specific EOI command
Master / Slave PIC OCW3 (WO)
Reserved. Must be set to 0.
Special Mask Mode.
00:
01:
10:
11:
No operation.
No operation.
Reset Special Mask Mode.
Set Special Mask Mode.
4
Reserved. Must be set to 0.
3
Reserved. Must be set to 1.
2
Poll Command.
0: Disable.
1: Enable.
1:0
Register Read Mode.
00:
01:
10:
11:
No operation.
No operation.
Read interrupt request register on next read of Port 20h.
Read interrupt service register on next read of Port 20h.
I/O Port 020h / 0A0h
Master / Slave PIC Interrupt Request and Service Registers
for OCW3 Commands (RO)
The function of this register is set with bits [1:0] in a write to 020h.
Interrupt Request Register
7
IRQ7 / IRQ15 Pending.
0: Yes.
1: No.
6
IRQ6 / IRQ14 Pending.
0: Yes.
1: No.
5
IRQ5 / IRQ13 Pending.
0: Yes.
1: No.
4
IRQ4 / IRQ12 Pending.
0: Yes.
1: No.
322
AMD Geode™ SC3200 Processor Data Book
Core Logic Module - ISA Legacy Register Space
Revision 5.1
Table 6-46. Programmable Interrupt Controller Registers (Continued)
Bit
3
Description
IRQ3 / IRQ11 Pending.
0: Yes.
1: No.
2
IRQ2 / IRQ10 Pending.
0: Yes.
1: No.
1
IRQ1 / IRQ9 Pending.
0: Yes.
1: No.
0
IRQ0 / IRQ8 Pending.
0: Yes.
1: No.
Interrupt Service Register
7
IRQ7 / IRQ15 In-Service.
0: No.
1: Yes.
6
IRQ6 / IRQ14 In-Service.
0: No.
1: Yes.
5
IRQ5 / IRQ13 In-Service.
0: No.
1: Yes.
4
IRQ4 / IRQ12 In-Service.
0: No.
1: Yes.
3
IRQ3 / IRQ11 In-Service.
0: No.
1: Yes.
2
IRQ2 / IRQ10 In-Service.
0: No.
1: Yes.
1
IRQ1 / IRQ9 In-Service.
0: No.
1: Yes.
0
IRQ0 / IRQ8 In-Service.
0: No.
1: Yes.
AMD Geode™ SC3200 Processor Data Book
323
Revision 5.1
Core Logic Module - ISA Legacy Register Space
Table 6-47. Keyboard Controller Registers
Bit
Description
I/O Port 060h
External Keyboard Controller Data Register (R/W)
Keyboard Controller Data Register. All accesses to this port are passed to the ISA bus. If the fast keyboard gate A20 and reset features are enabled through bit 7 of the ROM/AT Logic Control Register (F0 Index 52h[7]), the respective sequences of writes to this port
assert the A20M# signal or cause a warm CPU reset.
I/O Port 061h
7
Port B Control Register (R/W)
Reset Value: 00x01100b
PERR#/SERR# Status. (Read Only) Indicates if a PCI bus error (PERR#/SERR#) was asserted by a PCI device or by the
SC3200.
0: No.
1: Yes.
This bit can only be set if ERR_EN (bit 2) is set 0. This bit is set 0 after a write to ERR_EN with a 1 or after reset.
6
IOCHK# Status. (Read Only) Indicates if an I/O device is reporting an error to the SC3200.
0: No.
1: Yes.
This bit can only be set if IOCHK_EN (bit 3) is set 0. This bit is set 0 after a write to IOCHK_EN with a 1 or after reset.
5
PIT OUT2 State. (Read Only) This bit reflects the current status of the of the PIT Counter 2 (OUT2).
4
Toggle. (Read Only) This bit toggles on every falling edge of Counter 1 (OUT1).
3
IOCHK# Enable.
0: Generates an NMI if IOCHK# is driven low by an I/O device to report an error. Note that NMI is under SMI control.
1: Ignores the IOCHK# input signal and does not generate NMI.
2
PERR/ SERR Enable. Generate an NMI if PERR#/SERR# is driven active to report an error.
0: Enable.
1: Disable.
1
PIT Counter2 (SPKR).
0: Forces Counter 2 output (OUT2) to zero.
1: Allows Counter 2 output (OUT2) to pass to the speaker.
0
PIT Counter2 Enable.
0: Sets GATE2 input low.
1: Sets GATE2 input high.
I/O Port 062h
External Keyboard Controller Mailbox Register (R/W)
Keyboard Controller Mailbox Register.
I/O Port 064h
External Keyboard Controller Command Register (R/W)
Keyboard Controller Command Register. All accesses to this port are passed to the ISA bus. If the fast keyboard gate A20 and reset
features are enabled through bit 7 of the ROM/AT Logic Control Register (F0 Index 52h[7]), the respective sequences of writes to this
port assert the A20M# signal or cause a warm CPU reset.
I/O Port 066h
External Keyboard Controller Mailbox Register (R/W)
Keyboard Controller Mailbox Register.
I/O Port 092h
7:2
1
Port A Control Register (R/W)
Reset Value: 02h
Reserved. Must be set to 0.
A20M# Assertion. Assert A20# (internally).
0: Enable.
1: Disable.
This bit reflects A20# status and can be changed by keyboard command monitoring.
An SMI event is generated when this bit is changed, if enabled by F0 index 53h[0]. The SMI status is reported in F1BAR0+I/
O Offset 00h/02h[7].
0
Fast CPU Reset. WM_RST SMI is asserted to the BIOS.
0: Disable.
1: Enable.
This bit must be cleared before the generation of another reset.
324
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Core Logic Module - ISA Legacy Register Space
Table 6-48. Real-Time Clock Registers
Bit
Description
I/O Port 070h
RTC Address Register (WO)
This register is shadowed within the Core Logic module and is read through the RTC Shadow Register (F0 Index BBh).
7
NMI Mask.
0: Enable.
1: Mask.
6:0
RTC Register Index. A write of this register sends the data out on the ISA bus and also causes RTCALE to be triggered.
(RTCALE is an internal signal between the Core Logic module and the internal RTC controller.)
I/O Port 071h
RTC Data Register (R/W)
A read of this register returns the value of the register indexed by the RTC Address Register.
A write of this register sets the value into the register indexed by the RTC Address Register
I/O Port 072h
7
6:0
RTC Extended Address Register (WO)
Reserved.
RTC Register Index. A write of this register sends the data out on the ISA bus and also causes RTCALE to be triggered.
(RTCALE is an internal signal between the Core Logic module and the internal RTC controller.)
I/O Port 073h
RTC Data Register (R/W)
AA read of this register returns the value of the register indexed by the RTC Extended Address Register.
A write of this register sets the value into the register indexed by the RTC Extended Address Register
Table 6-49. Miscellaneous Registers
Bit
Description
I/O Port 0F0h, 0F1h
Coprocessor Error Register (W)
Reset Value: F0h
A write to either port when the internal FERR# signal is asserted causes the Core Logic Module to assert internal IGNNE#. IGNNE#
remains asserted until the FERR# de-asserts.
I/O Ports 170h-177h/376h-377h
Secondary IDE Registers (R/W)
When the local IDE functions are enabled, reads or writes to these registers cause the local IDE interface signals to operate according to
their configuration rather than generating standard ISA bus cycles.
I/O Ports 1F0h-1F7h/3F6h-3F7h
Primary IDE Registers (R/W)
When the local IDE functions are enabled, reads or writes to these registers cause the local IDE interface signals to operate according to
their configuration rather than generating standard ISA bus cycles.
I/O Port 4D0h
Interrupt Edge/Level Select Register 1 (R/W)
Reset Value: 00h
Notes: 1. If ICW1 - bit 3 in the PIC is set as level, it overrides the setting for bits [7:3] in this register.
2. Bits [7:3] in this register are used to configure a PCI interrupt mapped to IRQ[x] on the PIC as level-sensitive (shared).
7
IRQ7 Edge or Level Sensitive Select. Selects PIC IRQ7 sensitivity configuration.
0: Edge.
1: Level.
6
IRQ6 Edge or Level Sensitive Select. Selects PIC IRQ6 sensitivity configuration.
0: Edge.
1: Level.
5
IRQ5 Edge or Level Sensitive Select. Selects PIC IRQ5 sensitivity configuration.
0: Edge.
1: Level.
4
IRQ4 Edge or Level Sensitive Select. Selects PIC IRQ4 sensitivity configuration.
0: Edge.
1: Level.
AMD Geode™ SC3200 Processor Data Book
325
Revision 5.1
Core Logic Module - ISA Legacy Register Space
Table 6-49. Miscellaneous Registers (Continued)
Bit
3
Description
IRQ3 Edge or Level Sensitive Select. Selects PIC IRQ3 sensitivity configuration.
0: Edge.
1: Level.
2:0
Reserved. Must be set to 0.
I/O Port 4D1h
Interrupt Edge/Level Select Register 2 (R/W)
Reset Value: 00h
Notes: 1. If ICW1 - bit 3 in the PIC is set as level, it overrides the setting for bits 7:6 and 4:1 in this register.
2. Bits [7:6] and [4:1] in this register are used to configure a PCI interrupt mapped to IRQ[x] on the PIC as level-sensitive
(shared).
7
IRQ15 Edge or Level Sensitive Select. Selects PIC IRQ15 sensitivity configuration.
0: Edge.
1: Level.
6
IRQ14 Edge or Level Sensitive Select. Selects PIC IRQ14 sensitivity configuration.
0: Edge.
1: Level.
5
Reserved. Must be set to 0.
4
IRQ12 Edge or Level Sensitive Select. Selects PIC IRQ12 sensitivity configuration.
0: Edge.
1: Level.
3
IRQ11 Edge or Level Sensitive Select. Selects PIC IRQ11 sensitivity configuration.
0: Edge.
1: Level.
2
IRQ10 Edge or Level Sensitive Select. Selects PIC IRQ10 sensitivity configuration.
0: Edge.
1: Level.
1
IRQ9 Edge or Level Sensitive Select. Selects PIC IRQ9 sensitivity configuration.
0: Edge.
1: Level.
0
326
Reserved. Must be set to 0.
AMD Geode™ SC3200 Processor Data Book
Video Processor Module
Revision 5.1
7
7.0Video Processor Module
The Video Processor module contains a high performance
video back-end accelerator, a video/graphics Mixer/
Blender, a Video Input Port (VIP), supporting a TFT interface. The back-end accelerator functions include horizontal
and vertical scaling and filtering of the video stream. The
Mixer/Blender function includes color space conversion,
gamma correction, and mixing or alpha blending the video
and graphics streams.
Graphics-Video Overlay and Blending
• Overlay of video up to 16 bpp
• Supports chroma key and color key for both graphics
and video streams
• Supports alpha-blending with up to three alpha windows
that can overlap one another
General Features
• 8-Bit alpha values with automatic increment or decrement on each frame
• Hardware video acceleration
• Optional Gamma Correction for video or graphics
• Graphics/video overlay and blending
• Integrated PLL - programmable up to 135 MHz
Compatibility
• Selection of interlaced and progressive video from the
GX1 module and the Direct Video Port
• Supports Microsoft’s DirectDraw®/Direct Video and
Display Control Interface (DCI) Version 2.0 for full
motion playback acceleration
Video Input Port (VIP)
• Compliant with PC98 and PC99 V0.7
• CCIR-656 compatible
• Compatible with VESA, VGA, DPMS, and DDC2
standards for enhanced display control and power
management
• Capture Video/VBI modes
• Direct Video/VBI modes
Hardware Video Acceleration
• Arbitrary X and Y interpolation using three line-buffers
• YUV-to-RGB color space conversion
• Horizontal filtering and downscaling
• Supports 4:2:2, 4:2:0 YUV formats and RGB 5:6:5
format
AMD Geode™ SC3200 Processor Data Book
TFT Interface
• TFT modes:
— TFT on IDE: FPCLK max is 40 MHz
— TFT on Parallel Port: FPCLK max is 80 MHz
— 640x480x16 bpp at 60-85 Hz vertical refresh rates
— 800x600x16 bpp at 60-85 Hz vertical refresh rates
— 1024x768x16 bpp at 60-75 Hz vertical refresh rates
— 1280x1024x8 bpp at 60 Hz vertical refresh rate
327
Revision 5.1
7.1
Video Processor Module
Module Architecture
Figure 7-1 shows a top-level block diagram of the Video
Processor. For information about the relationship between
the Video Processor and the other modules of the SC3200,
see Section 2.2 on page 22. The Video Processor module
includes the following functions:
• Mixer/Blender
— Overlay with color/chroma key
— Gamma correction
— Color space converters
— Alpha blender
• Video Input Port
— CCIR-656 decoder
— Capture Video/VBI modes
— Direct Video mode
• TFT interface
• Dot Clock PLL
The following subsections describe each block in detail.
• Video Formatter
— Asynchronous video interface
— Horizontal/vertical scalers
— Filters
GX1 Graphics Data
Capture Video/VBI Data to
GX1 Video Frame Buffer
VIP Data
VIP
Capture Video/VBI
Controller and
Bus Master,
Direct Video/VBI
Controller
Video
Mux
Video
Data
Video Formatter
Horizontal Downscaler,
Line Buffer, Horizontal
and Vertical Upscalers,
and Filters
Mixer/Blender
Overlay with Gamma
RAM and Alpha
Blending
TFT_IF
Video Data from GX1 Video Port
Figure 7-1. Video Processor Block Diagram
328
AMD Geode™ SC3200 Processor Data Book
Video Processor Module
7.2
Functional Description
To understand why the Video Processor functions as it
does, it is first important to understand the difference
between video and graphics. Video is pictures in motion,
which usually starts out in an encoded format (i.e.,
MPEG2, AVI, MPEG4) or is a TV broadcast. These pictures or frames are generally dynamic and are drawn 24 to
30 frames per second. Conversely, graphic data is relatively static and is drawn - usually using hardware accelerators. Most IA devices need to support both video and
graphics displayed at the same time. For some IA devices,
such as set-top boxes, video is dominant. While for other
devices, such as consumer access devices and thin clients,
graphics is dominant. What this means for the Video Processor is that for video centric devices, graphics overlays
the video; and for graphics centric devices, video overlays
the graphics.
Video Support
The SC3200 gets video from two sources, either the VIP
block or the GX1 module’s video frame buffer. The VIP
block supports the CCIR-656 data protocol. The CCIR-656
protocol supports TV data (NTSC or PAL) and defines the
format for active video data and vertical blanking interval
(VBI) data. Conforming CCIR-656 data matches exactly
what is needed for a TV: full frame, interlaced, 27 MHz
pixel clock, and 50 or 60 Hz refresh rate. Full frame pixel
resolution and the refresh rate depends on the TV standard: NTSC, PAL, or SECAM.
Revision 5.1
VBI Support
VBI (vertical blanking interval) data is placed in the video
data stream during a portion of the vertical retrace period.
The vertical retrace period physically consists of several
horizontal lines (24 for NTSC and 25 for PAL systems) of
non-active video. Data can be placed on some of these
lines for other uses.
The active video and vertical retrace period horizontal lines
are logically defined into 23 types: logical line 2 through
logical line 24 (no logical line 1). Logical lines 2 through 23
occur during the vertical retrace period and logical line 24
represents all the active video lines. Logical lines 10
through 21 for NTSC and 6 through 23 for PAL are the
nominal VBI lines. The rest of the logical lines, 2 through 9,
22, and 23 for NTSC and 2 through 6 for PAL occur during
the vertical retrace period but do not normally carry user
data. An example of VBI usage is Closed Captioning,
which occupies VBI logical line 21 for NTSC. Figure 7-2
and Figure 7-3 on page 330 show the (relationship
between the) physical scan lines and logical scan lines for
the odd and even fields in the NTSC format.
If the VIP input data is full frame (conforming data), the
data can go directly from the VIP block to the Video Formatter. This is known as Direct Video mode. In this mode,
the data never leaves the Video Processor module. Direct
Video mode can only be used under very specific conditions which will be explained later. If the VIP data is less
than full frame (non conforming data), the VIP block will
bus master the video data to the GX1 module’s video frame
buffer. The GX1 module’s display controller then moves the
video data out of the video frame buffer and sends it to the
Video Formatter. Using this method the temporal (refresh
rate) and/or spatial (image less then full screen) differences
between the VIP data and the output device are reconciled.
This method is known as Capture Video mode. How each
mode is setup and operates is explained further in Section
7.2.1 on page 331.
AMD Geode™ SC3200 Processor Data Book
329
Revision 5.1
Video Processor Module
Vertical Retrace - Logical Lines 4-9 — Scan Lines 4-9
(Not normally User Data)
Vertical Retrace - Logical Lines 10-21 — Scan lines 10-21
(Nominal VBI Lines)
Vertical Retrace - Logical Lines 22, 23 — Scan lines 22, 23
VBI_Total_Count_Odd
(Not normally User Data)
Active Video
Logical Line 24 — Scan Lines 24-263
Vertical Retrace - Logical Line 24 — Scan Line 1
VBI_Line_Offset_Odd
Vertical Retrace - Logical Lines 2, 3 — Scan Lines 2, 3
(Not normally User Data)
VSYNC Start
VSYNC End
Figure 7-2. NTSC 525 Lines, 60 Hz, Odd Field
Vertical Retrace - Logical Lines 4-9 — Scan Lines 267-272
(Not normally User Data)
Nominal VBI Lines 10-21 — Scan lines 273-284
(Nominal VBI Lines)
Vertical Retrace - Logical Lines 22,23 — Scan lines 285, 286
VBI_Total_Count_Even
(Not normally User Data)
Active Video
Logical Line 24 — Scan Lines 287-525
VBI_Line_Offset_Even
Vertical Retrace - Logical Line 24 — Scan Line 264
Vertical Retrace - Logical Lines 2, 3 — Scan Lines 265, 266
(Not normally User Data)
VSYNC Start
VSYNC End
Figure 7-3. NTSC 525 Lines, 60 Hz, Even Field
330
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Video Processor Module
7.2.1
Video Input Port (VIP)
The VIP block is designed to interface the SC3200 with
external video processors (e.g., Philips PNX1300 or Sigma
Designs EM8400) or external TV decoders (e.g., Philips
SAA7114). It inputs CCIR-656 Video and raw VBI data
sourced by those devices, decodes the data, and delivers
the data directly to the Video Formatter (Direct Video
mode) or to the GX1 module’s video frame buffer (Capture
Video/VBI modes). Figure 7-4 shows a diagram of the VIP
block.
From the VIP block’s perspective, Direct Video mode is
always on. There are no registers that enable/disable
Direct Video mode. The data source selected at the video
mux (F4BAR0+Memory Offset 400h[1:0]) determines if the
data from the VIP interface is moved directly or must be
captured.
Two FIFOs in the VIP block support the efficient movement
of Video and VBI data. For Capture Video/VBI modes, a
128-byte FIFO buffers both Video and raw VBI data processed by the CCIR-656 decoder. For Direct Video mode,
there is a 2048-byte FIFO that buffer the CCIR-656
decoder’s video data. The FIFOs are also used to provide
clock domain changes. The VIP interface clock (nominally
27 MHz) is the input clock domain for both FIFOs. For the
Capture Video/VBI FIFO, the data is clocked out using the
FPCI clock (33 or 66 MHz). For the Direct Video FIFO, the
VSYNC
VIP_VSYNC
GenLock
Control
Video data is clocked out using the GX1’s Video port clock
(75, 116, or 133 MHz GX1 core clock divided by 2 or 4).
7.2.1.1 Direct Video Mode
As stated previously, Direct Video mode is on by default so
no registers need to be programmed to support this mode
other than to select the direct video data at the video mux.
The video mux control register is located at F4BAR0+Memory Offset 400h[1:0].
Direct Video mode while supported is not an optimal mode
of operation. This mode supports only one vertical resolution and refresh rate, which is that of the incoming data.
Horizontal resolution can be scaled if desired. Since the
incoming data has odd and even fields, incoming line must
be doubled for it to display properly. This is equivalent to
the Bob technique which is explained later in this section.
GenLock
Because video input data from the VIP is sent directly, without significant buffering frame-to-field synchronization is
required with the GX1 module’s graphics data. This synchronization is known as GenLock. The GenLock registers
are located at F4BAR0+Memory Offset 420h and 424h.
Stop DCLK
Fast
X-Bus Fast-PCI
to
Fast-PCI
Bridge
Capture Video/VBI
Controller and
Bus Master
GX1
Module
Fast-PCI Clock
VIP
Data
VIP
Clock
Capture Video/VBI
FIFO
CCIR-656
Decoder
Capture Video/VBI Data
to Video
Video Formatter
Mux
GX1 Video Clock
Direct Video
FIFO
Direct Video/VBI
Controller
Direct Video Data
F4BAR2
Control
Registers
Video or VBI Data
VIP
Figure 7-4. VIP Block Diagram
AMD Geode™ SC3200 Processor Data Book
331
Revision 5.1
The GenLock control hardware is used to synchronize the
video input’s field with the GX1 module’s graphics frame.
The graphics data is always sent full frame. For the GenLock function to perform correctly, the GX1 module’s Display Controller must be programmed to have a slightly
faster frame time then the video input’s field time. This is
best accomplished by programming the GX1 module’s Display Controller with a few less (three to five) horizontal lines
then the VIP interface. GenLock is accomplished by stopping the clock driving the GX1 module’s graphics frame
until the VIP vertical sync occurs (plus some additional
delay, via F4BAR0+Memory Offset 424h).
Video Processor Module
The following procedure is an example of how to create a
Bob method. This example assumes single buffering in the
GX1 module’s video frame buffer. The Video Processor
registers that control the VIP bus master only need to be
initialized.
1)
Three registers control where the VIP video data is
stored in the GX1 module’s frame buffer:
– F4BAR2+Memory Offset 20h – Video Data Odd
Base Address
– F4BAR2+Memory Offset 24h – Video Data Even
Base Address
The GenLock function provides a timeout feature
(GENLOCK_TOUT_EN, F4BAR0+Memory Offset 420h[4])
in case the video port input clock stops due to a problem
with incoming video.
7.2.1.2 Capture Video Mode
Capture Video mode is a process for bus mastering Video
data received from the VIP block to the GX1 module’s
Video Frame Buffer. The GX1 module’s Display Controller
then moves the data from the Video Frame Buffer to the
Video Formatter. Usually Capture Video mode is used
because the data coming in from the VIP block is interlaced
and has a 30 Hz refresh rate (NTSC format) and the TFT
panel, is progressive and has a 60 to 85 Hz refresh rate.
The Capture Video mode process must convert the interlaced data to progressive data and change the frames per
second. There are two methods to perform the interlaced
to progressive conversion; Bob and Weave. Each method
uses a different mechanism to up the refresh rate
Bob
The Bob method displays the odd frame followed by the
even frame. If a full-scale image is displayed, each line in
the odd and even field must be vertically doubled (see Section 7.2.2.5 "2-Tap Vertical and Horizontal Upscalers" on
page 337) because each odd and each even field only contain one-half a frames worth of data. This means that the
Bob method reduces the video image resolution, but has a
higher effective refresh rate. If there is a change of refresh
rate from the VIP block to the display device, then a field
will sometimes be displayed twice. The advantage of this
method is that the process is simple as only half the data is
transmitted from the GX1 module’s Video Frame Buffer to
the Video Processor per a given amount of time, therefore
reducing the memory bandwidth requirement. The disadvantage is that there are some observable visual effects
due to the reduction in resolution.
Program the VIP bus master address registers.
– F4BAR2+Memory Offset 28h – Video Data Pitch
The Video Data Even Base Address must be separated from the Video Data Odd Base Address by at
least the field data size. The Video Data Pitch register
must be programmed to 00000000h.
2)
Program other VIP bus master support registers.
In F4BAR2+Memory Offset 00h, make sure that the
VIP FIFO bus request threshold is set to 32 bytes (bit
22 = 1) and that the Video Input Port mode is set to
CCIR-656. An interrupt needs to be generated so that
the GX1 module’s video frame buffer pointer can flip to
the field that has completed transfer to the video frame
buffer. So in F4BAR2+Memory Offset 04h, enable the
Field Interrupt bit. Auto-Flip is normally set to allow the
CCIR-656 Decoder to identify which field is being processed. Capture video data needs to be enabled and
Run Mode Capture is set to Start Capture at beginning
of next field. Data is now being captured to the frame
buffer.
3)
Field Interrupt.
When the field interrupt occurs, the interrupt handler
must program the GX1 module’s video buffer start offset value (GX_BASE+Memory Offset 8320h) with the
address of the field that was just received from the VIP
interface. This action will cause the display controller
to ping-pong between the two fields. The new address
will not take affect until the start of a new display controller frame. The field that was just received can be
known by reading the Current Field bit at
F4BAR2+Memory Offset 08h[24].
Figure 7-5 on page 333 is an example of how the Bob
method is performed. The example assumes that the display device is a TFT at 85 Hz refresh and single buffering is
used for the data. The example does not assume anything
regarding scaling that may be performed in the Video Processor. The example is only presented to allow for a general understanding of how the SC3200’s video support
hardware works and not as an all-inclusive statement of
operation.
332
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Video Processor Module
Video Data Odd Base
(F4BAR2+Memory Offset 20h)
Address not changed
during runtime
Video Data Even Base
(F4BAR2+Memory Offset 24h)
Address not changed during runtime
Odd
Field
Even
Field
DC_VID_ST_OFFSET
(GX_BASE+Memory Offset 8320h)
Ping-pongs between the two buffers during runtime
GX1 Module’s Video Frame Buffer
30 frames per second
Buf #1
Capture video fill
sequence
Video subsystem
empty sequence
1
2
1
3
2
3
4
5
4
5
6
6
7
7
8
9
10
11
12
13
14
15
16
17
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
85 frames per second
Figure 7-5. Capture Video Mode Bob Example Using One Video Frame Buffer
Weave
The Weave method assembles the odd field and even field
together to form the complete frame, and then renders the
“weaved” frames to the display device. The Video data is
converted from interlaced to progressive. Since both fields
are rendered simultaneously, the GX1 module’s video
frame buffer must be at least double buffered. The Weave
method has the advantage of not creating the temporal
effects that Bob does. The disadvantage of Weave is twice
as much data is transferred from the video frame buffer to
the Video Processor; meaning that Weave uses more
memory bandwidth.
Figure 7-6 on page 334 is an example of the Weave
method in action. As in the Bob example (Figure 7-5), a
TPT panel at 85 Hz refresh is assumed. Double buffering
of the incoming data is also assumed. The example does
not assume anything about any scaling that may be done
in the Video Processor. No attempt has been made to
assure that this example is absolutely workable. The example is only presented to allow for a general understanding
of how the SC3200’s video support hardware works.
The following procedure is an example of how to create the
Weave method. Since at least double buffering is required,
more of the VIP’s control registers are used for Weave than
required for Bob during video runtime.
AMD Geode™ SC3200 Processor Data Book
1)
Program the VIP bus master address registers.
Three registers control where the VIP video data is
stored in the GX1 module’s frame buffer:
– F4BAR2+Memory Offset 20h – Video Data Odd
Base Address
– F4BAR2+Memory Offset 24h – Video Data Even
Base Address
– F4BAR2+Memory Offset 28h – Video Data Pitch
The Video Data Even Base Address must be separated from the Video Data Odd Base Address by one
horizontal line. The Video Data Pitch register must be
programmed to one horizontal line.
2)
Program other VIP bus master support registers.
Ensure the VIP FIFO Bus Request Threshold is set to
32 bytes (F4BAR2+Memory Offset 00h[22] = 1) and
the Video Input Port mode is set to CCIR-656
(F4BAR2+Memory Offset 00h[1:0] = 10). An interrupt
needs to be generated so that the GX1 module’s video
frame buffer pointer can flip to the field that has completed transfer to the video frame buffer. So the Field
Interrupt bit (F4BAR2+Memory Offset 04h[16] = 1).
must be enabled. Auto-Flip is normally set
(F4BAR2+Memory Offset 04h[10] = 0) to allow the
CCIR-656 decoder to identify which field is being processed. Capture video data needs to be enabled
(F4BAR2+Memory Offset 04h[10] = 1) and Run Mode
Capture is set to Start Capture (F4BAR2+Memory Offset 04h[1:0] = 11) at beginning of next field. Data is
now being captured to the frame buffer.
333
Revision 5.1
3)
Video Processor Module
Field Interrupt.
7.2.1.3 Capture VBI Mode
There are three types of VBI data defined by the CCIR-656
protocol: Task A data, Task B data, and Ancillary data. The
VIP block supports the capture for each data type. Generally Task A data is the data type captured. Just as in Capture Video mode, there are three registers that tell the bus
master where to put the raw VBI data in the GX1 module’s
frame buffer. Once the raw VBI data has been captured,
the data can be manipulated or decoded. The data can
also be used by an application. An example of this would
be an Internet address that is encoded on one or more of
the VBI lines, or have an application decode the Closed
Captioning information put in the graphics frame buffer.
When the field interrupt occurs on the completion of an
odd field, the interrupt must program the Video Data
Odd Base Address with the other buffer’s address. The
odd field will ping-pong between the two buffers. When
the interrupt is due to the completion of an even field,
the interrupt handler must program the GX1 module’s
video buffer start offset value (GX_BASE+Memory
Offset 8320h) with the address of the frame (both odd
and even fields) that was just received from the VIP
block. This new address will not take affect until the
start of a new frame. It must also program the Video
Data Even Base Address with the other buffer so that
the even field will ping-pong just like the odd field. The
field just received can be known by reading the Current Field bit (F4BAR2+Memory Offset 08h[24]).
The registers, F4BAR2+Memory Offset 40h, 44h, and 48h,
tell the bus master the destination addresses for the VBI
data in the GX1 module’s frame buffer. Five bits
(F4BAR2+Memory Offset 00h[21:17]) are used to tell the
bus master the data types to store. Capture VBI mode
needs to be enabled at F4BAR2+Memory Offset
04h[9,1:0]. The Field Interrupt bit (F4BAR2+Memory Offset
04h[16]) should be used by the software driver to know
when the captured VBI data has been completed for a field.
Ping-pongs between the two buffers during runtime
Video Data Odd Base
F4BAR2+Memory Offset 20h
Video Frame Buffer #1
Line 1 Odd Field
Line 1 Even Field
Video Data Even Base
F4BAR2+Memory Offset 24h
Video Frame Buffer #2
Video Data Even Base
F4BAR2+Memory Offset 20h
Line 1 Odd Field
Video Data Even Base
F4BAR2+Memory Offset 24h
Line 2 Odd Field
Line 1 Even Field
Line 2 Odd Field
Line 2 Even Field
Line 2 Even Field
VID_START_OFFSET
GX_BASE+Memory Offset 8320h
Ping-pongs between the
two buffers during runtime
Line n-1 Odd Field
Line n-1 Even Field
Line n-1 Odd Field
Line n-1 Even Field
Line n Odd Field
Line n Odd Field
Odd and Even fields are
“Weaved” together
Line n Even Field
Line n Even Field
GX1 Module’s Video Frame Buffer
Buf #1
Buf #2
30 frames per second
Capture video fill sequence
GX1 Module’s Display
Controller empty sequence
1
2
3
1
4
2
5
3
4
77
6
5
5
6
7
8
8
9
10
11
12
13
14
15
16
17
18
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
85 frames per second
Figure 7-6. Capture Video Mode Weave Example Using Two Video Frame Buffers
334
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Video Processor Module
7.2.2
Video Block
The Video block receives video data from the VIP block or
the GX1 module’s video frame buffer. The video data is formatted and scaled and then sent to the Mixer/Blender. The
video data also changes clock domains while in the Video
block. It is clocked in with the GX1 module’s video clock
and it is clocked out with the GX1 module’s graphics clock.
A diagram of the Video block is shown in Figure 7-7.
7.2.2.1 Video Input Formatter
The Video Input Formatter accepts video data 8 bits at a
time in YUV 4:2:2, YUV 4:2:0, or RGB 6:5:6 format. The
GX1 module’s video clock is the source clock. The data can
be interlaced or progressive. When the data comes directly
from the VIP block it is usually interlaced. The video format
is configured via the EN_42X bit (F4BAR0+Memory Offset
00h[28] and the GV_SEL bit (F4BAR0+Memory Offset
4Ch[13]). The byte order for each format is configured in
the VID_FMT bits (F4BAR0+Offset 00h[3:2]).
RGB 5:6:5 – For this format each pixel is described as a
16-bit value:
Bits [15:11] = Red
Bits [10:5] = Green
Bits [4:0] = Blue
YUV 4:2:0 – This format is not supported by the GX1 module. The Horizontal Downscaler in the Video block cannot
be used if the video data is in this format. In this format, 4
bytes of data are used to describe two pixels. The 4 bytes
contain two Y values one for each pixel; one U and one V
for both pixels. For each horizontal line, all the Y values are
received first. The U values are received next and the V
values are received last. For example for a horizontal line
that has 720 pixels, there are 720 bytes of Y, followed by
360 bytes of U, followed by 360 bytes of V.
YUV 4:2:2 – In this format each DWORD in the horizontal
line represent two pixels. There are two Y values and one
each U and V in a DWORD. Just as in the YUV 4:2:0 format, each U and V value describes the two pixels.
Video Input
Direct
Video
8
GX1
Module
8
Line Buffer 0
Video Input
Formatter
4-Tap Horizontal
Downscaler
m
or
m+1
1
m+1
Line Buffer 1
Formatter
4:4:4
Line Buffer 2
(3x360x32 bit)
(4:2:2 or 4:2:0)
24
24
2-Tap Vertical
Interpolating Upscaler
24
2-Tap Horizontal
Interpolating Upscaler
YUV 4:4:4/RGB 5:6:5
Figure 7-7. Video Block Diagram
AMD Geode™ SC3200 Processor Data Book
335
Revision 5.1
Video Processor Module
7.2.2.2 Horizontal Downscaler with 4-Tap Filtering
The Video Processor implements up to 8:1 horizontal
downscaling with 4-tap filtering for horizontal interpolation.
Filtering is performed on video data input to the Video Processor. This data is fed to the filter and then to the downscaler. There is a bypass path for both filtering and
downscaling logic. If this bypass is enabled, video data is
written directly into the line buffers. (See Figure 7-8.)
Filtering
There are four 4-bit coefficients which can have programmed values of 0 to 15. The filter coefficients can be
programmed via the Video Downscaler Coefficient register
(F4BAR0+Memory Offset 40h) to increase picture quality.
Horizontal Downscaler
The Video Processor supports horizontal downscaling. The
downscaler can be implemented in the Video Processor to
shrink the video window by a factor of up to 8:1, in 1-pixel
increments. The downscaler factor (m) is programmed in
the Video Downscaler Control register (F4BAR0+Memory
Offset 3Ch[4:1]). If bit 0 of this register is set to 0, the downscaler logic is bypassed.
The horizontal downscaler supports downscaling of video
data input format YUV 4:2:2 only.
The downscaler supports up to 29 downscaler factors.
There are two types of factors:
• Type A is (1/m+1). One pixel is retained, and m pixels
are dropped. This enables downscaling factors of 1/16,
1/15, 1/14, 1/13, 1/12, 1/11, 1/10, 1/9,1/8, 1/7, 1/6, 1/5,
1/4, 1/3, and 1/2.
• Type B is (m/m+1). m pixels are retained, and one pixel
is dropped. This enables downscaling factors of 2/3, 3/4,
4/5, 5/6, 6/7, 7/8, 8/9, 9/10, 10/11, 11/12, 12/13, 13/14,
14/15, and 15/16.
Bit 6 of the Video Downscaler Control register
(F4BAR0+Memory Offset 3Ch) selects the type of downscaling factor to be used.
Note:
There is no vertical downscaling in the Video Processor.
Bypass
To Line
Buffers
Video
Input
4-Tap
Filtering
Horizontal
Downscaler
4x4
Coefficients
Downscale
Factors
Figure 7-8. Horizontal Downscaler Block Diagram
336
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Video Processor Module
7.2.2.3 Line Buffers
After the data has been optionally horizontally downscaled
the video data is stored in a 3-line buffer. Each line is 360
DWORDs, which means a line width of up to 720 pixels can
be stored. This buffer supports two functions. First, the
clock domain of the video data changes from the GX1
module’s video clock to the GX1 module’s graphics clock.
This clock domain change is required because the video
data and graphics data can only be mixed/blended in the
same clock domain. The second function the line buffer
performs is to provide the necessary look ahead and look
behind data in the vertical direction for the vertical
upscaler. There is no direct program control of the line
buffer.
7.2.2.4 Formatter
Video data in YUV 4:2:2 or YUV 4:2:0 format is converted
to YUV 4:4:4 format. RGB data is not translated. There is
no direct program control of the Formatter.
7.2.2.5 2-Tap Vertical and Horizontal Upscalers
After the video data has been buffered, the upscaling algorithm can be applied. The Video Processor employs a Digital Differential Analyzer-style (DDA) algorithm for both
horizontal and vertical upscaling. The scaling parameters
are programmed via the Video Upscale register
(F4BAR0+Memory Offset 10h). The scalers support up to
8x factors for both horizontal and vertical scaling. The
scaled video pixel stream is then passed through bi-linear
interpolating filters (2-tap, 8-phase) to smooth the output
video, significantly enhancing the quality of the displayed
image.
The X and Y Upscaler uses the DDA and linear interpolating filter to calculate (via interpolation) the values of the pixels to be generated. The interpolation formula uses Ai,j,
Ai,j+1, Ai+1,j, and Ai+1,j+1 values to calculate the value of
intermediate points. The actual location of calculated
points is determined by the DDA algorithm.
The location of each intermediate point is one of eight
phases between the original pixels (see Figure 7-9).
Ai,j
Ai,j+1
x
Notes:
x and y are 0 - 7
8–y
y
b 1 = ( A i, j ) ------------ + ( A i + 1, j ) --8
8
y
b1
z
b2
8–y
y
b 2 = ( A i, j + 1 ) ------------ + ( A i + 1, j + 1 ) --8
8
8–x
x
z = ( b 1 ) ------------ + ( b 2 ) --8
8
Ai+1,j
Ai+1,j+1
Figure 7-9. Linear Interpolation Calculation
AMD Geode™ SC3200 Processor Data Book
337
Revision 5.1
7.2.3
Video Processor Module
Mixer/Blender Block
The Mixer/Blender block of the Video Processor module
performs all the necessary functions to properly mix/blend
the video data and the graphics data. These functions
include Color Space Conversion (CSC), optional Gamma
correction, color/chroma key, and the mixing/blending logic.
See Figure 7-10 for block diagram of the Mixer/Blender
Block.
Video/Graphics mixing/blending must be performed in the
RGB format. The YUV to RGB CSC (Section 7.2.3.1 on
page 339) must be used on the video data if it is in YUV
format. There is not a post mix/blend YUV to RGB CSC to
support the TFT output. If Gamma Correction (see Section
7.2.3.2) on the video data is desired, it must be done in the
color space of the input video data, which can be either
YUV or RGB. If Gamma Correction on the graphics data is
desired, it must be done in the color space of the input
graphics data, which is RGB.
The video data can be in progressive or interlaced format,
while the graphics data is always in the progressive format.
The Mixer/Blender can mix/blend either format of video
data with graphics data. F4BAR0+Memory Offset 4Ch[9]
programs the mix/blend format. Considering the color
space and the data format, the Mixer/Blender supports five
types of mixing/blending. Some of the mixing/blending
types have additional programming considerations to
enable them to work optimally. The valid mixing/blending
configurations are listed in see Table 7-1 on page 339
along with any additional programming requirements.
CSC_FOR_VIDEO
GV_GAMMA_SEL
CSC
YUV to
RGB
0
Video, 4:4:4
YUV or RGB
GV_GAMMA_SEL * /GAMMA_EN
0
0
1
1
1
Graphics,
RGB
Optional
Gamma
Correction
RAM
/GV_GAMMA_SEL * /GAMMA_EN
FLICKER_FILT_CNTRL = 01
0
1/2 Y
Flicker
Filter
Color/Chroma
Key and
Mixer/Blender
CRT DACs and
TFT Interface
1
1
1
Cursor Color Key
0
0
CSC_FOR_
GRAPHICS
CSC
RGB to
YUV
YUV Data
TVOUT Block
Compare
0
1
Compare
COLOR_CHROMA_SEL
Color/Chroma Key
Figure 7-10. Mixer/Blender Block Diagram
338
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Video Processor Module
Table 7-1. Valid Mixing/Blending Configurations
Flicker
Mixing/Blending1
(Bit)
Filter2 (Bit)
13
11
10
9
30
29
Mode
Comment
0
0
1
0
0
0
Input: YUV Progressive Video
•
Produces highest quality RGB output (see Section
7.2.1.2 "Capture Video Mode", Weave subsection on
page 333).
•
Produces highest quality RGB output (see Section
7.2.1.2 "Capture Video Mode", Weave subsection on
page 333).
•
Not supported.
•
Not supported.
•
Typically Direct Video mode.
•
Must be vertically upscaled by a factor of 2 (see
Section 7.2.2.5 "2-Tap Vertical and Horizontal
Upscalers" on page 337).
Mixing: RGB
1
0
0
0
0
0
Input: RGB Progressive Video
Mixing: RGB
0
1
0
1
0
1
Input: YUV Interlaced Video
Mixing: YUV
0
1
0
0
0
0
Input: YUV Progressive Video
0
0
1
0
0
0
Input: YUV Interlaced Video
upscaled by 2
Mixing: YUV
Mixing: RGB
1.
2.
F4BAR0+Memory Offset 4Ch[13, 11:9].
F4BAR0+Memory Offset 814h[30:29].
7.2.3.1 YUV to RGB CSC in Video Data Path
This CSC must be enabled if the video data is in the YUV
color space. The CSC_FOR_VIDEO bit, F4BAR0+Memory
Offset 4Ch[10], controls this CSC.
YUV video data is passed through this CSC to obtain 24-bit
RGB data using the following CCIR-601-1 recommended
formula:
• R = 1.1640625(Y – 16) + 1.59375(V – 128)
• G = 1.1640625(Y – 16) – 0.8125(V – 128) –
0.390625(U – 128)
• B = 1.1640625(Y – 16) + 2.015625(U – 128)
The CSC clamps inputs to prevent them from exceeding
acceptable limits.
7.2.3.2 Gamma Correction
Either the video or graphics data can be routed through an
integrated palette RAM for Gamma correction. There are
three 256-byte RAMs, one for each color component value.
Gamma correction supported in the YUV or RGB color
space for the video data and RGB color space for the
graphics data. Gamma correction is accomplished by treating each color component as an address into each RAM.
The output of the RAM is the new color. A simple RGB
Gamma correction example is to increase each color component by one. The address 00h in the RAMs would contain the data 01h. The address 01h would contain the data
02h and so on. This would have the effect of increasing
each original Red, Green, and Blue value by one.
AMD Geode™ SC3200 Processor Data Book
• G_V_GAMMA, F4BAR0+Memory Offset 04h[21] selects
which data path (video or graphics) to send to the
Gamma correction block. GAMMA_EN,
F4BAR0+Memory Offset 28h[0] enables the Gamma
correction function. To load the Gamma correction
palette RAM, use F4BAR0+Memory Offset 1Ch and
20h.
7.2.3.3 Color/Chroma Key
A color/chroma key mechanism is used to support the
Mixer/Blender logic. There are two keys: key1 is for the cursor and key2 is for graphics or video data. Key1, the cursor
key, is always a color key. The cursor color key registers
are located at, F4BAR0+Memory Offset 50h-5CF. How the
cursor key mechanism works with the Mixer/Blender is
explained in Section 7.2.3.4. COLOR_CHROMA_KEY
(F4BAR0+Memory Offset 04h[20]) determines whether
key2 is a color key or a chroma key. The Video Color Key
Register (F4BAR0+Memory Offset 14h) stores the key.
Color keying is used when video is overlaid on the graphics
(GFX_INS_VIDEO, F4BAR0+Memory Offset 4Ch[8] = 0).
Chroma keying is used when graphics is overlaid on the
video (GFX_INS_VIDEO = 1). How the color/chroma key
mechanism works with the Mixer/Blender is explained in
Section 7.2.3.4.
339
Revision 5.1
Video Processor Module
7.2.3.4 Color/Chroma Key and Mixer/Blender
The Mixer/Blender takes each pixel of the graphics and
video data streams and mixes or blends them together.
Mixing is simply choosing the graphics pixel or the video
pixel. Blending takes a percentage of a graphics pixel
(Alpha_value * Graphics_pixel_value) and percentage of
the video pixel (1 - Alpha_Value * Video_pixel_value) and
adds them together. The percentages of each add up to
100%. The actual formula is:
PAL). Vertical scaling is not allowed. Horizontal scaling is
allowed. If the video source is from the GX1 module’s video
frame buffer (which includes Capture Video mode, see
Section 7.2.1.2 "Capture Video Mode" on page 332) then
the video data can be scaled both horizontally and vertically. The video data size, scaled or unscaled, must equal
the video window size. The Video X Position (horizontal)
and Video Y Position (vertical) registers (F4BAR0+Memory
Offset 08h and 0Ch) define the video window.
• Blended Pixel = (Alpha_value * Graphics_pixel_value) /
256 + ((256 – Alpha_value) * Video_pixel_value) / 256
Cursor Window
The cursor window can be managed two ways: with the
GX1 module’s hardware cursor or a software cursor. When
using the hardware cursor, the displayed colors of the hardware cursor must be the cursor color keys (see Section
5.5.3 “Hardware Cursor” in the AMD Geode™ GX1 Processor Data Book). When the software cursor is used, the
cursor size and position are not defined using registers.
The cursor size, position, and image are determined
through the use of the cursor color key colors in the graphics frame buffer. When the cursor is described in this manner, the cursor can be of any size and shape.
Where: Alpha_value = 0 to 255
Mixing and blending are supported simultaneously for
every rendered frame, however, each pixel can only be
mixed or blended. The mix or blend question is decided by
the pixel position, whether video is overlaid on the graphics
or visa versa (GFX_INS_VIDEO, F4BAR0+Memory Offset
4Ch[8]), and several programmed “windows”. Figure 7-11
illustrates and example frame.
Graphics Window
The graphics window is defined in the GX1 module’s display controller and is always the full screen resolution.
Alpha Windows
Up to three alpha windows can be defined. They are used
only for blending. They can be of any size up to the graphics window size and they may overlap. To support overlapping of the alpha windows they can be prioritized as to
which one is on top (F4BAR0+Memory Offset 4Ch[20:16]).
The alpha windows are programmed at F4BAR0+Memory
Offset 60h-88h.
Video Window
The video window tells the Mixer/Blender where the video
window is and its size. If Direct Video mode is enabled (see
Section 7.2.1.1 "Direct Video Mode" on page 331), the
video window must be defined as the resolution of the
video port data resolution (720x480 for NTSC, 720x576 for
Graphics Window (GFX_INS_VIDEO = 0)
Video Window
Video X
Position Register
Video Y
Position
Register
Alpha Window #1
ALPHA1_WIN_PRIORITY = 10
ALPHA2_WIN_PRIORITY = 01
ALPHA3_WIN_PRIORITY = 00
Alpha Window #2
Cursor
Window
Alpha Window 3
X Position
Register
Alpha
Window 3
Y Position
Register
Alpha Window #3
Figure 7-11. Graphics/Video Frame with Alpha Windows
340
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Video Processor Module
Mixing/Blending Operation
Table 7-2 on page 341 shows the truth table used to create the flow diagram, Figure 7-12 on page 342, that the Mixer/
Blender logic uses to determine each pixels disposition.
Table 7-2. Truth Table for Alpha Blending
Video Data
Match
Normal
Color Key
Windows
Configuration2
x
x
x
Yes
x
x
Cursor Color
x
Not in Video
Window
x
No
x
x
Graphics Data
Graphics Color
Key
Not in an Alpha
Window
GFX_INS_VIDEO = 0
No
Yes
x
Video Data
No
No
x
Graphics Data
GFX_INS_VIDEO = 1
No
x
x
Video Data
ALPHAx_COLOR_REG_EN = 1
No
Yes
x
Color from
Color Register
ALPHAx_COLOR_REG_EN = 0
No
Yes
x
Video Data
x
No
No
x
Alpha-blended
Data
GFX_INS_VIDEO = 0
No
x
Yes
Graphics Data
No
x
No
Video Data
GFX_INS_VIDEO = 1
No
x
x
Graphics Data
ALPHAx_COLOR_REG_EN = 1
No
x
Yes
Color from
Color Register
ALPHAx_COLOR_REG_EN = 0
No
x
Yes
Graphics Data
x
No
x
No
Alpha-blended
Data
COLOR_
CHROMA_SEL1
(COLOR_
CHROMA_SEL
= 0)
Video Chroma
Key
(COLOR_
CHROMA_SEL
= 1)
1.
2.
Graphics
Data Match
Normal
Color Key
Graphics
Data Match
Cursor
Color Key
Inside Alpha
Window x
Not in an Alpha
Window
Inside Alpha
Window x
Mixer Output
COLOR_CHROMA_SEL: F4BAR0+Memory Offset 04h[20].
GFX_INS_VIDEO: F4BAR0+Memory Offset 4Ch[8].
ALPHAx_COLOR_REG_EN: F4BAR0+Memory Offsets 68h[24], 78h[24], and 88h[24].
AMD Geode™ SC3200 Processor Data Book
341
Revision 5.1
Video Processor Module
Start
Use selected cursor color for pixel
Yes
Cursor color
key matches
graphics value
No
Use graphics
value for this pixel
Yes
Pixel outside
the video
window
No
Pixel inside1
alpha window
No
“Graphics2
inside Video”
is enabled
Yes
Blend graphics
values and video
values using the
alpha value for
this window
No
No
Pixel value3
matches
normal color
key
Pixel value3
matches
normal color
key
Yes
Color register
enabled for this
window
COLOR_CHROMA
_SEL = 1
No
COLOR_CHROMA
_SEL = 1
Yes
No
Yes
Replace the value
with the color
register value
Yes
Yes
COLOR_CHROMA
_SEL = 1
No
Yes
No
Yes
No
Use video value
for this pixel
Use graphics
value for this pixel
Use video value
for this pixel
Use graphics
value for this pixel
Notes:
1)
Alpha window should not be placed outside of the video window.
2)
“Graphics inside Video” is enabled via bit GFX_INS_VIDEO in the Video De-interlacing and Alpha Control register
(F4BAR0+Memory Offset 4Ch[8]).
3)
The “Pixel Value” refers to either the Video value or the Graphics value, depending on the setting of bit COLOR_CHROMA_SEL
in the Display Configuration register (F4BAR0+Memory Offset 04h[20]).
Figure 7-12. Color Key and Alpha Blending Logic
342
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Video Processor Module
7.2.4
TFT Interface
• TFTDCK - data clock signal.
The TFT interface can be programmed to one of two sets of
balls: IDE balls or Parallel Port balls. PMR[23] of the General Configuration registers program where the TFT interface exists (see Table 4-2 on page 88).
Note:
If the TFT interface is on the IDE balls, the maximum FPCLK supported is 40 MHz. If the TFT interface is on the Parallel Port balls the maximum
FPCLK supported is 80 MHz.
Support for a TFT panel requires power sequencing and an
18-bit (6-bit RGB), digital output. The relevant digital output
signals are available from the SC3200.
TFT output signals are:
• TFTD[5:0] for blue signals
• TFTD[11:6] for green signals
• TFTD[17:12] for red signals
• TFTDE - data enable signal.
• FP_VDD_ON - power control signal
Power Sequence
Power sequence is used to
FP_VDD_ON and TFTD signals.
control
assertion
of
All bits related to power sequence configuration are located
in the Display Configuration register (F4BAR0+Memory
Offset 04h).
After enabling TFT_EN (bit 0), and FP_PWR_EN (bit 6),
the state machine waits until the next VSYNC to switch on
the FP_VDD_ON signal. The state machine then asserts
the TFTD[17:0] signals after the delay programmed via
PWR_SEQ_DLY (bits [19:17]) When FP_PWR_EN (bit 6)
is set to 0, the reverse sequence happens for powering
down the TFT.
• HSYNC and VSYNC - sync signals
T0 is time to next VSYNC
T1 is a programmable multiple of frame time
FP_PWR_EN
bit
T0
FP_VDD_ON
T1
T1
TFTD[17:0],
HSYNC, VSYNC,
TFTDE, TFTDCK
T0+T1
Figure 7-13. TFT Power Sequence
AMD Geode™ SC3200 Processor Data Book
343
Revision 5.1
7.2.5
Video Processor Module
Integrated PLL
The integrated PLL can generate frequencies up to 135
MHz from a single 27 MHz source. The clock frequency is
programmable using two registers. Figure 7-14 shows the
block diagram of the Video Processor integrated PLL.
FREF is 27 MHz, generated by an external crystal and an
integrated oscillator. FOUT is calculated from:
The integrated PLL can generate any frequency by writing
into the “m” and “n” bit fields (FBAR0+Memory Offset 2Ch,
m = bits [14:8] and n = bits [3:0]). Additionally, 16 preprogrammed VGA frequencies can be selected via the PLL
Clock
Select
register
(F4BAR0+Memory
Offset
2Ch[19:16]), if the crystal oscillator has a frequency of 27
MHz. This PLL can be powered down via the Miscellaneous register (F4BAR0+Memory Offset 28h[12]).
FOUT = (m + 1) / (n+ 1) x FREF
FREF
n
Divider
Phase
Compare
Charge
Pump
Loop
Filter
VCO
Out
Divide
FOUT
m
Divider
Figure 7-14. PLL Block Diagram
344
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Video Processor Module - Register Summary
7.3
Register Descriptions
The register space for accessing and configuring the Video
Processor is located in the Core Logic Chipset Register
Space (F0-F5). The Chipset Register Space is accessed
via the PCI interface using the PCI Type One Configuration
Mechanism (see Section 6.3.1 "PCI Configuration Space
and Access Methods" on page 191).
7.3.1
Register Summary
The tables in this subsection summarize the registers of
the Video Processor. Included in the tables are the register’s reset values and page references where the bit formats are found.
Table 7-3. F4: PCI Header Registers for Video Processor Support Summary
Width
(Bits)
Type
00h-01h
16
02h-03h
16
04h-05h
16
R/W
PCI Command Register
0000h
Page 348
06h-07h
16
RO
PCI Status Register
0280h
Page 348
08h
8
RO
Device Revision ID Register
01h
Page 348
09h-0Bh
24
RO
PCI Class Code Register
0Ch
8
RO
0Dh
8
RO
F4 Index
Name
Reset
Value
Reference
(Table 7-6)
RO
Vendor Identification Register
100Bh
Page 348
RO
Device Identification Register
0504h
Page 348
030000h
Page 348
PCI Cache Line Size Register
00h
Page 348
PCI Latency Timer Register
00h
Page 348
0Eh
8
RO
PCI Header Type Register
00h
Page 348
0Fh
8
RO
PCI BIST Register
00h
Page 348
10h-13h
32
R/W
Base Address Register 0 (F4BAR0). Sets the base address for the
memory-mapped Video Configuration Registers within the Video
Processor. Refer to Table 7-7 on page 350 for programming information regarding the register offsets accessed through this register.
00000000h
Page 348
14h-17h
32
R/W
Base Address Register 1 (F4BAR1). Reserved.
00000000h
Page 348
18h-1Bh
32
R/W
Base Address Register 2 (F4BAR2). Sets the base address for the
memory-mapped VIP (Video Interface Port) Registers (summarized in Table 7-8 on page 363).
00000000h
Page 348
1Ch-2Bh
--
--
00h
Page 348
2Ch-2Dh
16
RO
Reserved
Subsystem Vendor ID
100Bh
Page 348
2Eh-2Fh
16
RO
Subsystem ID
0504h
Page 348
30h-3Bh
--
--
3Ch
8
R/W
3Dh
8
R/W
3Eh-FFh
---
---
Reserved
00h
Page 348
Interrupt Line Register
00h
Page 348
Interrupt Pin Register
03h
Page 349
Reserved
00h
Page 349
Table 7-4. F4BAR0: Video Processor Configuration Registers Summary
F4BAR0+
Memory
Offset
Width
(Bits)
Type
Name
Reset
Value
Reference
(Table 7-7)
00h-03h
32
R/W
Video Configuration Register
00000000h
Page 350
04h-07h
32
R/W
Display Configuration Register
x0000000h
Page 351
08h-0Bh
32
R/W
Video X Position Register
00000000h
Page 352
0Ch-0Fh
32
R/W
Video Y Position Register
00000000h
Page 352
10h-13h
32
R/W
Video Upscaler Register
00000000h
Page 352
14h-17h
32
R/W
Video Color Key Register
00000000h
Page 353
18h-1Bh
32
R/W
Video Color Mask Register
00000000h
Page 353
1Ch-1Fh
32
R/W
Palette Address Register
xxxxxxxxh
Page 353
20h-23h
32
R/W
Palette Data Register
xxxxxxxxh
Page 353
24h-27h
32
RO
Reserved
---
Page 353
AMD Geode™ SC3200 Processor Data Book
345
Revision 5.1
Video Processor Module - Register Summary
Table 7-4. F4BAR0: Video Processor Configuration Registers Summary (Continued)
F4BAR0+
Memory
Offset
Width
(Bits)
Type
Name
Reset
Value
Reference
(Table 7-7)
28h-2Bh
32
R/W
Miscellaneous Register
00001400h
Page 354
2Ch-2Fh
32
R/W
PLL2 Clock Select Register
00000000h
Page 354
Page 354
30h-33h
32
---
Reserved
00000000h
34h-37h
32
RO
Reserved
00000000h
Page 354
38h-3Bh
32
RO
Reserved
00000000h
Page 354
3Ch-3Fh
32
R/W
Video Downscaler Control Register
00000000h
Page 355
Page 355
40h-43h
32
R/W
Video Downscaler Coefficient Register
00000000h
44h-47h
32
R/W
CRC Signature Register
xxxxx100h
Page 355
48h-4Bh
32
RO
Device and Revision Identification
0000015xh
Page 355
4Ch-4Fh
32
R/W
Video De-Interlacing and Alpha Control Register
00060000h
Page 356
50h-53h
32
R/W
Cursor Color Key Register
00000000h
Page 357
54h-57h
32
R/W
Cursor Color Mask Register
00000000h
Page 357
58h-5Bh
32
R/W
Cursor Color Register 1
00000000h
Page 357
5Ch-5Fh
32
R/W
Cursor Color Register 2
00000000h
Page 357
60h-63h
32
R/W
Alpha Window 1 X Position Register
00000000h
Page 358
64h-67h
32
R/W
Alpha Window 1 Y Position Register
00000000h
Page 358
68h-6Bh
32
R/W
Alpha Window 1 Color Register
00000000h
Page 358
6Ch-6Fh
32
R/W
Alpha Window 1 Control Register
00000000h
Page 358
70h-73h
32
R/W
Alpha Window 2 X Position Register
00000000h
Page 359
74h-77h
32
R/W
Alpha Window 2 Y Position Register
00000000h
Page 359
78h-7Bh
32
R/W
Alpha Window 2 Color Register
00000000h
Page 359
7Ch-7Fh
32
R/W
Alpha Window 2 Control Register
00000000h
Page 359
80h-83h
32
R/W
Alpha Window 3 X Position Register
00000000h
Page 360
84h-87h
32
R/W
Alpha Window 3 Y Position Register
00000000h
Page 360
88h-8Bh
32
R/W
Alpha Window 3 Color Register
00000000h
Page 360
8Ch-8Fh
32
R/W
Alpha Window 3 Control Register
00000000h
Page 360
90h-93h
32
R/W
Video Request Register
001B0017h
Page 361
94h-97h
32
RO
Alpha Watch Register
00000000h
Page 361
---
Reserved
---
Page 361
00000000h
Page 361
98h-3FFh
400h-403h
32
R/W
404h-407h
32
---
408h-40Bh
32
R/W
40Ch-41Fh
---
---
420h-423h
32
R/W
424h-427h
32
R/W
428h-43Bh
---
---
43Ch-43Fh
32
R/W
346
Video Processor Display Mode Register
Reserved
00000000h
Page 361
Video Processor Test Mode Register
00000000h
Page 361
Reserved
00000000h
Page 361
GenLock Register
00000000h
Page 362
GenLock Delay Register
00000000h
Page 362
---
Page 362
1FFF1FFFh
Page 362
Reserved
Continuous GenLock Time-out Register
AMD Geode™ SC3200 Processor Data Book
Video Processor Module - Register Summary
Revision 5.1
Table 7-5. F4BAR2: VIP Support Registers Summary
F4BAR2+
Memory
Offset
Width
(Bits)
Type
Name
Reset
Value
Reference
(Table 7-8)
00h-03h
32
R/W
Video Interface Port Configuration Register
00000000h
Page 363
04h-07h
32
R/W
Video Interface Control Register
00000000h
Page 363
08h-0Bh
32
R/W
Video Interface Status Register
xxxxxxxxh
Page 364
Page 365
0Ch-0Fh
--
--
Reserved
00000000h
10h-13h
32
RO
Video Current Line Register
xxxxxxxxh
Page 365
14h-17h
32
R/W
Video Line Target Register
00000000h
Page 365
18h-1Fh
---
---
Reserved
00000000h
Page 365
20h-23h
32
R/W
Video Data Odd Base Register
00000000h
Page 365
24h-27h
32
R/W
Video Data Even Base Register
00000000h
Page 365
28h-2Bh
32
R/W
Video Data Pitch Register
00000000h
Page 365
2Ch-3Fh
--
--
Reserved
00000000h
Page 365
40h-43h
32
R/W
VBI Data Odd Base Register
00000000h
Page 366
44h-47h
32
R/W
VBI Data Even Base Register
00000000h
Page 366
48h-4Bh
32
R/W
VBI Data Pitch Register
00000000h
Page 366
4Ch-1FFh
--
--
Reserved
00000000h
Page 366
AMD Geode™ SC3200 Processor Data Book
347
Revision 5.1
7.3.2
Video Processor Module - Video Processor Registers - Function 4
Video Processor Registers - Function 4
The register space designated as Function 4 (F4) is used
to configure the PCI portion of support hardware for
accessing the Video Processor support registers, including
VIP (separate BAR). The bit formats for the PCI Header
registers are given in Table 7-6.
Located in the PCI Header Registers of F4 are three Base
Address Registers (F4BARx) used for pointing to the register spaces designated for Video Processor support.
F4BAR0 is for Video Processor Configuration, F4BAR1 is
reserved, and F4BAR2 is for VIP configuration.
Table 7-6. F4: PCI Header Registers for Video Processor Support Registers
Bit
Description
Index 00h-01h
Vendor Identification Register (RO)
Reset Value: 100Bh
Index 02h-03h
Device Identification Register (RO)
Reset Value: 0504h
Index 04h-05h
PCI Command Register (R/W)
Reset Value: 0000h
15:2
1
Reserved. (Read Only)
Memory Space. Allow the Core Logic module to respond to memory cycles from the PCI bus.
0: Disable.
1: Enable.
This bit must be enabled to access memory offsets through F4BAR0, F4BAR1, and F4BAR2 (see F4 Index 10h, 14h, and
18h).
0
Reserved. (Read Only)
Index 06h-07h
Index 08h
PCI Status Register (RO)
Device Revision ID Register (RO)
Index 09h-0Bh
PCI Class Code Register (RO)
Reset Value: 0280h
Reset Value: 01h
Reset Value: 030000h
Index 0Ch
PCI Cache Line Size Register (RO)
Reset Value: 00h
Index 0Dh
PCI Latency Timer Register (RO)
Reset Value: 00h
Index 0Eh
PCI Header Type (RO)
Reset Value: 00h
Index 0Fh
PCI BIST Register (RO)
Reset Value: 00h
Index 10h-13h
Base Address Register 0 - F4BAR0 (R/W)
Reset Value: 00000000h
Video Processor Video Memory Address Space. This register allows PCI access to the memory mapped Video Processor configuration registers. Bits [11:0] are read only (0000 0000 0000) indicating a 4 KB memory address range. See Table 7-7 on page 350 for bit
formats and reset values of the registers accessed through this base address register.
31:12
Video Processor Video Memory Base Address.
11:0
Address Range. (Read Only)
Index 14h-17h
Base Address Register 1 - F4BAR1 (R/W)
Reset Value: 00000000h
Base Address Register 2 - F4BAR2 (R/W)
Reset Value: 00000000h
Reserved
Index 18h-1Bh
VIP Address Space. This register allows access to memory mapped VIP (Video Interface Port) related registers. Bits [11:0] are read
only (0000 0000 0000), indicating a 4 KB I/O address range. Refer to Table 7-8 for the VIP register bit formats and reset values.
31:12
VIP Base Address.
11:0
Address Range. (Read Only)
Index 1Ch-2Bh
Reserved
Index 2Ch-2Dh
Subsystem Vendor ID (RO)
Reset Value: 100Bh
Index 2Eh-2Fh
Subsystem ID (RO)
Reset Value: 0504h
Index 30h-3Bh
Reserved
Reset Value: 00h
Interrupt Line Register (R/W)
Reset Value: 00h
Index 3Ch
Reset Value: 00h
This register identifies the system interrupt controllers to which the device’s interrupt pin is connected. The value of this register is used
by device drivers and has no direct meaning to this function.
348
AMD Geode™ SC3200 Processor Data Book
Video Processor Module - Video Processor Registers - Function 4
Revision 5.1
Table 7-6. F4: PCI Header Registers for Video Processor Support Registers (Continued)
Bit
Description
Index 3Dh
Interrupt Pin Register (R/W)
Reset Value: 03h
This register selects which interrupt pin the device uses. VIP uses INTC# after reset. INTA#, INTB# or INTD# can be selected by writing
1, 2 or 4, respectively.
Index 3Eh-FFh
AMD Geode™ SC3200 Processor Data Book
Reserved
Reset Value: 00h
349
Revision 5.1
Video Processor Module - Video Processor Registers - Function 4
7.3.2.1 Video Processor Support Registers - F4BAR0
F4 Index 10h, Base Address Register 0 (F4BAR0) sets the
base address that allows PCI access to the Video Processor support registers, not including VIP. A separate base
address register (F4BAR2) is used to access VIP support
registers (see Section 7.3.2.2 on page 363).
Note:
Reserved bits that are not defined as “must be set
to 0 or 1" should be written with a value that is read
from them.
Table 7-7. F4BAR0+Memory Offset: Video Processor Configuration Registers
Bit
Description
Offset 00h-03h
Video Configuration Register (R/W)
Reset Value: 00000000h
Configuration register for options of the motion video acceleration hardware.
31:29
28
Reserved. Must be set to 0.
EN_42X (Enable 4:2:x Format). Allows format selection.
0: 4:2:2 format.
1: 4:2:0 format.
Note: When input video stream is RGB (i.e., F4BAR0+Memory Offset 4Ch[13] = 1), this bit must be set to 0.
27
BIT_8_LINE_SIZE. When enabled, this bit increases line size from VID_LIN_SIZ (bits [15:8]) DWORDs by adding 256
DWORDs.
0: Disable.
1: Enable.
26:25
Reserved. Must be set to 0.
24:16
INIT_RD_ADDR (Initial Buffer Read Address). This field preloads the starting read address for the line buffers at the
beginning of each display line. It is used for hardware clipping of the video window at the left edge of the active display. It
represents the DWORD address of the source pixel which is to be displayed first.
For an unclipped window, this value should be 0. For 4:2:0 format, set bits [17:16] to 00.
15:8
7
VID_LIN_SIZ (Video Line Size). Represents the number of DWORDs that make up the horizontal size of the source video
data.
YFILT_EN (Y Filter Enable). Enables/disables the vertical filter.
0: Disable. Upscaling done by repeating pixels.
1: Enable. Upscaling done by interpolating pixels.
Note: This bit is used with Y upscaling logic. Reset to 0 when not required.
6
XFILT_EN (X Filter Enable). Enables/disables the horizontal filter.
0: Disable. Upscaling done by repeating pixels.
1: Enable. Upscaling done by interpolating pixels.
Note: This bit is used with X upscaling logic. Reset to 0 when not required.
5:4
Reserved.
3:2
VID_FMT (Video Format). Byte ordering of video data on the Video Input bus (VPD[7:0]). The interpretation of these bits
depends on the settings of bit 13 (GV_SEL) in the Video De-Interlacing and Alpha Control register (F4BAR0+Memory Offset
4Ch) and bit 28 (EN_42X) of this register.
If GV_SEL = 0 and EN_42X = 0:
00: Cb Y0 Cr Y1
01: Y1 Cr Y0 Cb
10: Y0 Cb Y1 Cr
11: Y0 Cr Y1 Cb
If GV_SEL = 0 and EN_42X = 1:
00: Y0 Y1 Y2 Y3
01: Y3 Y2 Y1 Y0
10: Y1 Y0 Y3 Y2
11: Y1 Y2 Y3 Y0
If GV_SEL = 1 and EN_42X = 0:
00: P1L P1M P2L P2M
01: P2M P2L P1M P1L
10: P1M P1L P2M P2L
11: P1M P2L P2M P1L
If GV_SEL = 1 and EN_42X = 1: Reserved
Note:
1
350
Both RGB 5:6:5 and YUV 4:2:2 contain two pixels in each 32-bit DWORD. YUV 4:2:0 contains a stream of Y data
for each line, followed by U and V data for that same line.
Reserved.
AMD Geode™ SC3200 Processor Data Book
Video Processor Module - Video Processor Registers - Function 4
Revision 5.1
Table 7-7. F4BAR0+Memory Offset: Video Processor Configuration Registers (Continued)
Bit
0
Description
VID_EN (Video Enable). Enables video acceleration hardware.
0: Disable (reset) video module.
1: Enable.
Offset 04h-07h
Display Configuration Register (R/W)
Reset Value: x0000000h
General configuration register for display control. This register is also used to determine how graphics and video data are to be combined in the display on the output device.
31
30:28
27
Reserved. Write as read.
Reserved.
FP_ON_STATUS (Flat Panel On Status). (Read Only) Shows whether power to the attached flat panel is on or off. This bit
transitions at the end of the power-up or power-down sequence.
0: Power to the flat panel is off.
1: Power to the flat panel is on.
26
Reserved. Set to 0.
25
Reserved. Must be set to 0.
24:22
21
Reserved. Set to 0.
GV_GAMMA_SEL (Graphics or Video Gamma Source Data). Selects whether the graphics or video data goes to the
Gamma Correction RAM. GAMMA_EN (F4BAR0+Memory Offset 28h[0]) must be enabled for the selected data source to
pass through the Gamma Correction RAM.
0: Graphics data to Gamma Correction RAM.
1: Video data to Gamma Correction RAM.
Note:
20
Gamma Correction is always in the RGB domain for graphics data.
Gamma Correction can be in the YUV or RGB domain for video data.
COLOR_CHROMA_SEL (Color or Chroma Key Select). Selects whether the graphics is used for color keying or the video
data stream is used for chroma keying.
0: Graphics data is compared to the color key.
1: Video data is compared to the chroma key.
19:17
PWR_SEQ_DLY (Power Sequence Delay). Selects the number of frame periods that transpire between successive transitions of the power sequence control lines.
16:14
Reserved. Write as read.
13:8
Reserved. Write as read.
7
FP_DATA_EN (Flat Panel Output Enable). Controls the data, data-enable, clock and sync output signals.
0: Flat panel data outputs are forced to zero depending on the value of bit 3 (BL_EN). Bit 6 (FP_PWR_EN) is ignored.
1: Flat panel outputs are forced to zero until power-up, and later, data outputs are subject to the value of bit 3 (BL_EN).
6
FP_PWR_EN (Flat Panel Power Enable). Changing this bit initiates a flat panel power-up or power-down.
0-to-1: Power-up flat panel.
1-to-0: Power-down flat panel.
5:4
3
Reserved.
BL_EN (Blank Enable). Controls blanking of TFT data.
0: TFT data is constantly blanked.
1: TFT data is blanked normally (i.e., during horizontal and vertical blank).
2
VSYNC_EN (Vertical Sync Enable). Enables/disables display vertical sync (used for VESA DPMS support).
0: Disable.
1: Enable.
1
HSYNC_EN (Horizontal Sync Enable). Enables/disables display horizontal sync (used for VESA DPMS support).
0: Disable.
1: Enable.
0
TFT_EN (TFT Enable). Enables the TFT control logic and is also used to reset the TFT control logic.
0: Reset TFT control logic.
1: Enable TFT control logic.
AMD Geode™ SC3200 Processor Data Book
351
Revision 5.1
Video Processor Module - Video Processor Registers - Function 4
Table 7-7. F4BAR0+Memory Offset: Video Processor Configuration Registers (Continued)
Bit
Description
Offset 08h-0Bh
Video X Position Register (R/W)
Reset Value: 00000000h
Provides the window X position. This register is programmed relative to CRT horizontal sync input (not physical screen position).
Note:
H_TOTAL and H_SYNC_END are values programmed in the GX1 module’s Display Controller Timing registers
(GX_BASE+Memory Offset 8330h[26:19] and 8338h[10:3], respectively). The value of (H_TOTAL – H_SYNC_END) is sometimes referred to as “horizontal back porch”. For more information, see the AMD Geode™ GX1 Processor Data Book.
31:28
Reserved.
27:16
VID_X_END (Video X End Position). Represents the horizontal end position of the video window (not inclusive). This value
is calculated according to the following formula:
Value = Desired screen position + (H_TOTAL – H_SYNC_END) – 13.
15:12
Reserved.
11:0
VID_X_START (Video X Start Position). Represents the horizontal start position of the video window. This value is calculated according to the following formula:
Value = Desired screen position + (H_TOTAL – H_SYNC_END) – 14.
Offset 0Ch-0Fh
Video Y Position Register (R/W)
Reset Value: 00000000h
Provides the window Y position. This register is programmed relative to CRT vertical sync input (not physical screen position).
Note:
V_TOTAL and V_SYNC_END are values programmed in the GX1 module’s Display Controller Timing registers
(GX_BASE+Memory Offset 8340h[26:16] and 8348h[26:16], respectively). The value of (V_TOTAL – V_SYNC_END) is sometimes referred to as “vertical back porch”. For more information, see the AMD Geode™ GX1 Processor Data Book.
31:27
Reserved.
26:16
VID_Y_END (Video Y End Position). Represents the vertical end position of the video window (not inclusive). This value is
calculated according to the following formula:
Value = Desired screen position + (V_TOTAL – V_SYNC_END) + 2.
15:11
Reserved
10:0
VID_Y_START (Video Y Start Position). Represents the vertical start position of the video window. This value is calculated
according to the following formula:
Value = Desired screen position + (V_TOTAL – V_SYNC_END) + 1.
Offset 10h-13h
Video Upscale Register (R/W)
Reset Value: 00000000h
Provides horizontal and vertical upscale factors of the window.
31:30
Reserved.
29:16
VID_Y_SCL (Video Y Scale Factor). Represents the vertical upscale factor of the video window according to the following
formula:
VID_Y_SCL = 8192 * (Ys - 1) / (Yd - 1)
where:
Ys = Video source vertical size in pixels
Yd = Video destination vertical size in pixels
Note:
Upscale factor must be used. Yd is equal or bigger than Ys. If no scaling is intended, set to 2000h. The actual scale
factor used is VID_Y_SCL/8192, but the formula above fits a given source number of lines into a destination window size.
Note:
When progressive mixing/blending is programmed (F4BAR0+Memory Offset 4Ch[9] = 0) and the video data is
interlaced, this register should be programmed to 1000h to double the vertical lines,
15:14
Reserved.
13:0
VID_X_SCL (Video X Scale Factor). Represents horizontal upscale factor of the video window according to the following
formula:
VID_X_SCL = 8192 * (Xs - 1) / (Xd - 1)
where:
Xs = Video source horizontal size in pixels
Xd = Video destination vertical size in pixels
Note:
352
Upscale factor must be used. Xd is equal or bigger than Xs. If no scaling is intended, set to 2000h. The actual scale
factor used is VID_X_SCL/8192, but the formula above fits a given source number of pixels into a destination window size.
AMD Geode™ SC3200 Processor Data Book
Video Processor Module - Video Processor Registers - Function 4
Revision 5.1
Table 7-7. F4BAR0+Memory Offset: Video Processor Configuration Registers (Continued)
Bit
Description
Offset 14h-17h
Video Color Key Register (R/W)
Reset Value: 00000000h
Provides the video color key. The color key can be used to allow irregular shaped overlays of graphics onto video, or video onto graphics, within a scaled video window.
31:24
Reserved.
23:0
VID_CLR_KEY (Video Color Key). The video color key is a 24-bit RGB or YUV value.
•
If the COLOR_CHROMA_SEL bit (F4BAR0+Memory Offset 04h[20]) = 0:
— The video pixel is selected within the target window if the corresponding graphics pixel matches the color key. The
color key in an RGB value.
•
If the COLOR_CHROMA_SEL bit (F4BAR0+Memory Offset 04h[20]) = 1:
— The video pixel is selected within the target window only if it (the video pixel) does not match the color key. The color
key is usually an RGB value. However, if both the CSC_for VIDEO and GV_SEL bits (F4BAR0+Memory Offset 4Ch
bits 10 and 13, respectively) are programmed to 0, the color key is a YUV value (i.e., video is not converted to RGB).
The graphics or video data being compared can be masked prior to the compare via the Video Color Mask register
(described in F4BAR0+Memory Offset 18h).
Offset 18h-1Bh
Video Color Mask Register (R/W)
Reset Value: 00000000h
Provides the video color mask. This value is used to mask bits of the graphics or video stream being compared to the video color key
(described in F4BAR0+Memory Offset 14h). It can be used to allow a range of values to serve as the color key.
31:24
Reserved.
23:0
VID_CLR_MASK (Video Color Mask). This mask is a 24-bit value. Zeros in the mask cause the corresponding bits in the
graphics or video stream to be ignored.
Offset 1Ch-1Fh
Palette (Gamma Correction RAM) Address Register (R/W)
Reset Value: xxxxxxxxh
31:8
Reserved.
7:0
PAL_ADDR (Palette Address). Specifies the address to be used for the next access to the Palette Data register
(F4BAR0+Memory Offset 20h[31:8]). Each access to the data register automatically increments the Palette Address register. If non-sequential access is made to the palette, the address register must be loaded between each non-sequential data
block.
Offset 20h-23h
Palette (Gamma Correction RAM) Data Register (R/W)
Reset Value: xxxxxxxxh
Provides the video palette data. The data can be read or written to the Gamma Correction RAM (palette) via this register. Prior to
accessing this register, an appropriate address should be loaded to the Palette Address register (F4BAR0+Memory Offset 1Ch[7:0]).
Subsequent accesses to the Palette Data register cause the internal address counter to be incremented for the next cycle.
31:8
PAL_DATA (Palette Data). Contains the read or write data for a Gamma Correction RAM (palette).
Blue[7:0] = Bits [31:24]
Green[7:0] = Bits [23:16]
Red[7:0] = Bits [15:8]
Note:
7:0
When a read or write to the Gamma Correction RAM occurs, the previous output value is held for one additional
DOTCLK period. This effect should go unnoticed during normal operation.
Reserved.
Offset 24h-27h
AMD Geode™ SC3200 Processor Data Book
Reserved
353
Revision 5.1
Video Processor Module - Video Processor Registers - Function 4
Table 7-7. F4BAR0+Memory Offset: Video Processor Configuration Registers (Continued)
Bit
Description
Offset 28h-2Bh
Miscellaneous Register (R/W)
Reset Value: 00001400h
Configuration and control register for miscellaneous characteristics of the Video Processor.
31:13
12
Reserved.
PLL2_PWR_EN (PLL2 Power-Down Enable).
0: Power-down.
1: Normal.
11:10
9:1
0
Reserved. Set to 1.
Reserved.
GAMMA_EN (Gamma Correction RAM Enable). Allows video or graphics (selected by F4BAR0+Memory Offset 04h[21])
to go to the Gamma Correction RAM.
0: Enable.
1: Disable.
Offset 2Ch-2Fh
PLL2 Clock Select Register (R/W)
Reset Value: 00000000h
Determines the characteristics of the integrated PLL2.
31:23
Reserved. Must be set to 0.
22:21
CLK_DIV_SEL (Clock Divider Select).
00: No division
01: Divide by 2
10: Divide by 4
11: Divide by 8
Divides the clock generated by the PLL2, using the programmed m (bits [14:8]) and n (bits [3:0]) values.
20
SEL_REG_CAL. Selects specific or previously-calculated values.
0: Values previously calculated from the CLK_SEL bits (bits [19:16]).
1: Values according to the m (bits [14:8]), n (bits [3:0]), and CLK_DIV_SEL (bits [22:21]) fields.
19:16
CLK_SEL (Clock Select). Selects frequency (in MHz) of the display clock.
0000: 25.175
0001: 31.5
0010: 36
0011: 40
15
14:8
0100: 50
0101: 49.5
0110: 56.25
0111: 44.9
1000: 65
1001: 75
1010: 78.5
1011: 94.5
1100: 108
1101: 135
1110: 27
1111: 24.923052
LFTC (Loop Filter Time Constant). This bit should be set when m (bits [14:8]) value is higher than 30.
m (Defines m PLL2 Value). Relevant when SEL_REG_CAL (bit 20) = 1. The following formula is used for calculating the
frequency using m and n values:
Fvco
Km
Kn
OSCCLK
= OSCCLK * Km/Kn
=m+1
=n+1
= 27 MHz
7:4
Reserved
3:0
n (Defines n PLL2 Value). Relevant when SEL_REG_CAL (bit 20) = 1. The following formula is used for calculating the frequency using m and n values:
Fvco
Km
Kn
OSCCL
= OSCCLK * Km/Kn
=m+1
=n+1
= 27 MHz
Offset 30h-33h
Reserved
Reset Value: 00000000h
Offset 34h-37h
Reserved
Reset Value: 00000000h
Offset 38h-3Bh
Reserved
Reset Value: 00000000h
354
AMD Geode™ SC3200 Processor Data Book
Video Processor Module - Video Processor Registers - Function 4
Revision 5.1
Table 7-7. F4BAR0+Memory Offset: Video Processor Configuration Registers (Continued)
Bit
Description
Offset 3Ch-3Fh
Video Downscaler Control Register (R/W)
Reset Value: 00000000h
Controls the characteristics of the integrated video downscaler.
31:7
6
Reserved
DTS (Downscale Type Select).
0: Type A (Downscale formula is 1/m+1, m pixels are dropped, 1 pixel is kept).
1: Type B (Downscale formula is m/m+1, m pixels are kept, 1 pixel is dropped).
5
4:1
0
Reserved.
DFS (Downscale Factor Select). Determines the downscale factor to be programmed into these bits, where m is used to
derive the desired downscale factor depending on bit 6 (DTS).
DCF (Downscaler and Filtering). Enables/disables downscaler and filtering logic.
0: Disable.
1: Enable.
Note:
No downscaling support for RGB 5:6:5 and YUV 4:2:0 video formats.
Offset 40h-43h
Video Downscaler Coefficient Register (R/W)
Reset Value: 00000000h
Indicates filter coefficients. The filters can be programmed independently to increase video quality when the downscaler is implemented.
Valid values for each filter coefficient are 0-15. The sum of coefficients must be 16. FLT_CO_4 is used with the earliest pixels and
FLT_CO_1 is used with the latest. Only luminance values of pixels are filtered.
31:28
Reserved
27:24
FLT_CO_4 (Filter Coefficient 4). For the tap-4 filter.
23:20
Reserved
19:16
FLT_CO_3 (Filter Coefficient 3). For the tap-3 filter.
15:12
Reserved
11:8
FLT_CO_2 (Filter Coefficient 2). For the tap-2 filter.
7:4
Reserved
3:0
FLT_CO_1 (Filter Coefficient 1). For the tap-1 filter.
Offset 44h-47h
CRC Signature Register (R/W)
Reset Value: xxxxx100h
Signature values stored in this register can be read by the host. This register is used for test purposes.
31:8
SIG_VALUE (Signature Value). (Read Only) A 24-bit signature value is stored in this bit field and can be read at any time.
The signature is produced from the RGB data output of the mixer. This bit field is used for test purpose only.
See SIGN_EN (bit 0) description for more information.
7:3
2
Reserved
SIGN_FREE (Signature Free Run).
0: Disable. (Default) If this bit was previously set to 1, the signature process stops at the end of the current frame (i.e., at
the next falling edge of VSYNC).
1: Enable. If SIGN_EN (bit 0) = 1, the signature register captures data continuously across multiple frames.
1
Reserved.
0
SIGN_EN (Signature Enable).
0: Disable. (Default) The SIG_VALUE (bits [31:8]) is reset to 000001h and held (no capture).
1: Enable. The next falling edge of VSYNC is counted as the start of the frame to be used for CRC checking with each pixel
clock beginning with the next VSYNC.
If SIGN_FREE (bit 2) = 1, the signature register captures the pixel data signature continuously across multiple frames.
If SIGN_FREE (bit 2) = 0, a signature is captured for one frame at a time, starting from the next falling VSYNC.
After a signature capture, the SIG_VALUE can be read to determine the CRC check status. SIGN_EN can then be reset to
initialize the SIG_VALUE as an essential preparation for the next round of CRC check.
Offset 48h-4Bh
31:16
Device and Revision Identification (RO)
Reset Value: 0000xxxxh
Reserved.
15:8
REV_ID (Revision ID). See the AMD Geode™ SC3200 Specification Update document for value.
7:0
DEV_ID (Device ID). See the AMD Geode™ SC3200 Specification Update document for value.
AMD Geode™ SC3200 Processor Data Book
355
Revision 5.1
Video Processor Module - Video Processor Registers - Function 4
Table 7-7. F4BAR0+Memory Offset: Video Processor Configuration Registers (Continued)
Bit
Description
Offset 4Ch-4Fh
Video De-Interlacing and Alpha Control Register (R/W)
Reset Value: 00060000h
31:22
Reserved.
21:20
ALPHA3_WIN_PRIORITY (Alpha Window 3 Priority). Determines the priority of Alpha Window 3. A higher number indicates a higher priority. Priority is used to determine display order for overlapping alpha windows.
00: Lowest priority (default).
01: Medium priority.
10: Highest priority.
11: Illegal.
Note:
19:18
Priority of enabled alpha windows must be different.
ALPHA2_WIN_PRIORITY (Alpha Window 2 Priority). Determines the priority of Alpha Window 2. A higher number indicates a higher priority. Priority is used to determine display order for overlapping alpha windows.
00: Lowest priority (default).
01: Medium priority.
10: Highest priority.
11: Illegal.
Note:
17:16
Priority of enabled alpha windows must be different.
ALPHA1_WIN_PRIORITY (Alpha Window 1 Priority). Determines the priority of Alpha Window 1. A higher number indicates a higher priority. Priority is used to determine display order for overlapping alpha windows.
00: Lowest priority (default).
01: Medium priority.
10: Highest priority.
11: Illegal.
Note:
15:14
13
Priority of enabled alpha windows must be different.
Reserved
GV_SEL (GV Select). Selects input video format.
0: YUV format.
1: RGB format.
Note:
Mixing and blending configurations are created using bits [13, 11:9] of this register. See Table 7-1 "Valid Mixing/
Blending Configurations" on page 339.
If this bit is set to 1, EN_42X (F4BAR0+Memory Offset 00h[28]) must be programmed to 0.
12
VID_LIN_INV (Video Line Invert). When this bit is set, it allows the video window to be positioned at odd offsets with
respect to the first line. The values below are recommended if VID_Y_START (F4BAR0+Memory Offset 0Ch[10:0]) is an
odd (set to 1) or even (set to 0) number of lines from the start of the active display.
0: Even.
1: Odd.
11
Reserved: Set to 0.
10
CSC_FOR_VIDEO (Color Space Converter for Video). Determines whether or not the video stream from the video module is passed through the CSC.
0: Disable. The video stream is sent "as is" to the video Mixer/Blender.
1: Enable. The video stream is passed through the CSC (for YUV to RGB conversion).
Note:
9
Mixing and blending configurations are created using bits [13,11:9] of this register. See Table 7-1 "Valid Mixing/
Blending Configurations" on page 339.
VIDEO_BLEND_MODE (Video Blending Mode). Allows selection of the type of video (i.e., interlaced or progressive) used
for blending.
0: Progressive video used for blending.
1: Interlaced video used for blending.
Note:
356
Mixing and blending configurations are created using bits [13,11:9] of this register. See Table 7-1 "Valid Mixing/
Blending Configurations" on page 339.
AMD Geode™ SC3200 Processor Data Book
Video Processor Module - Video Processor Registers - Function 4
Revision 5.1
Table 7-7. F4BAR0+Memory Offset: Video Processor Configuration Registers (Continued)
Bit
8
Description
GFX_INS_VIDEO (Graphics Inside Video). This bit works in conjunction with bit COLOR_CHROMA_SEL (F4BAR0+Memory Offset 4Ch[20]). COLOR_CHROMA_SEL selects whether the graphics is used for color keying or the video data stream
is used for chroma keying. If COLOR_CHROMA_SEL = 0, graphics data is compared to the color key. If
COLOR_CHROMA_SEL = 1, video data is compared to the chroma key.
0: Outside the alpha windows, graphics or video is displayed depending on the result of the color key comparison.
1: Outside the alpha windows, only video is displayed (if COLOR_CHROMA_SEL = 0) or only graphics is displayed (if
COLOR_CHROMA_SEL = 1) color key comparison is not performed outside the alpha windows.
7
VID_WIN_PUSH_EN (Video Window Push Enable). Video window repositioning at an offset of 1 line below the programmed value. Facilitates line rate matching in both fields.
0: Disable. (Default)
1: Enable.
6
TOP_LINE_IN_ODD (Top Line in Odd Field). Allows selection of what field the top line is in.
0: Top line is in even field. (Default)
1: Top line is in odd field.
5
Reserved.
4
INSERT_EN (Insert Enable). When this bit is set, the odd frame is shifted with respect to the even frame.
0: No shifting occurs.
1: The odd frame is shifted according to the offset specified in bits [2:0].
3
2:0
Reserved.
OFFSET (Vertical Scaler Offset). For a non-interlaced video stream and when bob de-interlacing is used, program a value
of 100 (i.e., shift one line); otherwise, leave at 000.
Offset 50h-53h
Cursor Color Key Register (R/W)
Reset Value: 00000000h
31:29
Reserved.
28:24
COLOR_REG_OFFSET (Cursor Color Register Offset). This field indicates a bit in the incoming graphics stream. It is
used to indicate which of the two possible cursor color registers should be used for color key matches for the bits in the
graphics stream.
23:0
CUR_COLOR_KEY (Cursor Color Key). Specifies the 24-bit RGB value of the cursor color key. The incoming graphics
stream is compared with this value. If a match is detected, the pixel is replaced by a 24-bit value from one of the Cursor
Color registers.
Offset 54h-57h
Cursor Color Mask Register (R/W)
Reset Value: 00000000h
31:24
Reserved
23:0
CUR_COLOR_MASK (Cursor Color Mask). This mask is a 24-bit value. Zeroes in the mask cause the corresponding bits
in the incoming graphics stream to be ignored.
Offset 58h-5Bh
Cursor Color Register 1 (R/W)
Reset Value: 00000000h
31:24
Reserved
23:0
CUR_COLOR_REG1 (Cursor Color Register 1). Specifies a 24-bit cursor color value. This is an RGB value (for RGB
blending) or a YUV value (for YUV blending). In interlaced YUV blending mode, Y/2 value should be used.
This is one of two possible cursor color values. The COLOR_REG_OFFSET bits (F4BAR0+Memory Offset 50h[28:24])
determine a bit of the graphics data that if even, selects this color to be used.
Offset 5Ch-5Fh
Cursor Color Register 2 (R/W)
Reset Value: 00000000h
31:24
Reserved
23:0
CUR_COLOR_REG2 (Cursor Color Register 2). Specifies a 24-bit cursor color value. This is an RGB value (for RGB
blending) or a YUV value (for YUV blending). In interlaced YUV blending mode, Y/2 value should be used.
This is one of two possible cursor color values. The COLOR_REG_OFFSET bits (F4BAR0+Memory Offset 50h[28:24])
determine a bit of the graphics data that if even, selects this color to be used.
AMD Geode™ SC3200 Processor Data Book
357
Revision 5.1
Video Processor Module - Video Processor Registers - Function 4
Table 7-7. F4BAR0+Memory Offset: Video Processor Configuration Registers (Continued)
Bit
Description
Offset 60h-63h
Note:
Alpha Window 1 X Position Register (R/W)
Reset Value: 00000000h
H_TOTAL and H_SYNC_END are values programmed in the GX1 module’s Display Controller Timing registers
(GX_BASE+Memory Offset 8330h[26:19] and 8338h[10:3], respectively). The value of (H_TOTAL – H_SYNC_END) is sometimes referred to as “horizontal back porch”. For more information, see the AMD Geode™ GX1 Processor Data Book.
Desired screen position should not be outside a video window (F4BAR0+Memory Offset 08h and 0Ch).
31:27
Reserved.
26:16
ALPHA1_X_END (Alpha Window 1 Horizontal End). Determines the horizontal end position of Alpha Window 1 (not inclusive). This value is calculated according to the following formula:
Value = Desired screen position + (H_TOTAL – H_SYNC_END) – 1.
15:11
Reserved.
10:0
ALPHA1_X_START (Alpha Window 1 Horizontal Start). Determines the horizontal start position of Alpha Window 1. This
value is calculated according to the following formula:
Value = Desired screen position + (H_TOTAL – H_SYNC_END) – 2.
Offset 64h-67h
Note:
Alpha Window 1 Y Position Register (R/W)
Reset Value: 00000000h
V_TOTAL and V_SYNC_END are values programmed in the GX1 module’s Display Controller Timing registers
(GX_BASE+Memory Offset 8340h[26:16] and 8348h[26:16], respectively). The value of (V_TOTAL – V_SYNC_END) is sometimes referred to as “vertical back porch”. For more information, see the AMD Geode™ GX1 Processor Data Book.
Desired screen position should not be outside a video window (F4BAR0+Memory Offset 08h and 0Ch).
31:27
Reserved.
26:16
ALPHA1_Y_END (Alpha Window 1 Vertical End). Determines the vertical end position of Alpha Window 1 (not inclusive).
This value is calculated according to the following formula:
Value = Desired screen position + (V_TOTAL – V_SYNC_END) + 2.
15:11
Reserved.
10:0
ALPHA1_Y_START (Alpha Window 1 Vertical Start). Determines the vertical start position of Alpha Window 1. This value
is calculated according to the following formula:
Value = Desired screen position + (V_TOTAL – V_SYNC_END) + 1.
Offset 68h-6Bh
31:25
24
Alpha Window 1 Color Register (R/W)
Reset Value: 00000000h
Reserved.
ALPHA1_COLOR_REG_EN (Alpha Window 1 Color Register Enable). Enable bit for the color key matching in Alpha
Window 1.
1: Enable. If this bit is enabled and the alpha window is enabled, then where there is a color key match. The color value (in
bits [23:0], ALPHA1_COLOR_REG) is displayed.
0: Disable. Where there is a color key match, no blending is performed.
23:0
ALPHA1_COLOR_REG (Alpha Window 1 Color Register). Specifies the color to be displayed inside Alpha Window 1
when there is a color key match in the alpha window. This is an RGB value (for RGB blending) or a YUV value (for YUV
blending). In interlaced YUV blending mode, Y/2 value should be used.
This color is only displayed if the alpha window is enabled and bit 24 (ALPHA1_COLOR_REG_EN) is enabled.
Offset 6Ch-6Fh
31:18
Alpha Window 1 Control Register (R/W)
Reset Value: 00000000h
Reserved.
17
LOAD_ALPHA (Load Alpha Value). (Write Only) When set to 1, this bit causes the Video Processor to load the alpha
value (in bits [7:0], ALPHA_VAL) at the start of the next frame.
16
ALPHA1_WIN_EN (Alpha Window 1 Enable). Enable bit for Alpha Window 1.
1: Enable Alpha Window 1.
0: Disable Alpha Window 1.
Note:
358
Valid only if video window is enabled (F4BAR0+Memory Offset 00h[0] = 1).
15:8
ALPHA1_INC (Alpha Window 1 Increment). Specifies the alpha value increment/decrement. This is a signed 8-bit value
that is added to the alpha value for each frame. The MSB (bit 15) indicates the sign (i.e., increment or decrement). When
this value reaches either the maximum or the minimum alpha value (255 or 0) it keeps that value (i.e., it is not incremented/
decremented) until it is reloaded via bit 17 (LOAD_ALPHA).
7:0
ALPHA1_VAL (Alpha Window 1 Value). Specifies the alpha value to be used for this window.
AMD Geode™ SC3200 Processor Data Book
Video Processor Module - Video Processor Registers - Function 4
Revision 5.1
Table 7-7. F4BAR0+Memory Offset: Video Processor Configuration Registers (Continued)
Bit
Description
Offset 70h-73h
Note:
Alpha Window 2 X Position Register (R/W)
Reset Value: 00000000h
H_TOTAL and H_SYNC_END are values programmed in the GX1 module’s Display Controller Timing registers
(GX_BASE+Memory Offset 8330h[26:19] and 8338h[10:3], respectively). The value of (H_TOTAL – H_SYNC_END) is sometimes referred to as “horizontal back porch”. For more information, see the AMD Geode™ GX1 Processor Data Book.
Desired screen position should not be outside a video window (F4BAR0+Memory Offset 08h and 0Ch).
31:27
Reserved.
26:16
ALPHA2_X_END (Alpha Window 2 Horizontal End). Determines the horizontal end position of Alpha Window 2 (not inclusive). This value is calculated according to the following formula:
Value = Desired screen position + (H_TOTAL – H_SYNC_END) – 1.
15:11
Reserved
10:0
ALPHA2_X_START (Alpha Window 2 Horizontal Start). Determines the horizontal start position of Alpha Window 2. This
value is calculated according to the following formula:
Value = Desired screen position + (H_TOTAL – H_SYNC_END) – 2.
Offset 74h-77h
Note:
Alpha Window 2 Y Position Register (R/W)
Reset Value: 00000000h
V_TOTAL and V_SYNC_END are values programmed in the GX1 module’s Display Controller Timing registers
(GX_BASE+Memory Offset 8340h[26:16] and 8348h[26:16], respectively). The value of (V_TOTAL – V_SYNC_END) is sometimes referred to as “vertical back porch”. For more information, see the AMD Geode™ GX1 Processor Data Book.
Desired screen position should not be outside a video window (F4BAR0+Memory Offset 08h and 0Ch).
31:27
Reserved.
26:16
ALPHA2_Y_END (Alpha Window 2 Vertical End). Determines the vertical end position of Alpha Window 2 (not inclusive).
This value is calculated according to the following formula:
Value = Desired screen position + (V_TOTAL – V_SYNC_END) + 2.
15:11
Reserved.
10:0
ALPHA2_Y_START (Alpha Window 2 Vertical Start). Determines the vertical start position of Alpha Window 2. This value
is calculated according to the following formula:
Value = Desired screen position + (V_TOTAL – V_SYNC_END) + 1.
Offset 78h-7Bh
31:25
24
Alpha Window 2 Color Register (R/W)
Reset Value: 00000000h
Reserved.
ALPHA2_COLOR_REG_EN (Alpha Window 2 Color Register Enable). Enable bit for the color key matching in Alpha
Window 2.
0: Disable. Where there is a color key match, graphics and video are alpha-blended.
1: Enable. If this bit is enabled and the alpha window is enabled, then where there is a color key match, the color value (in
bits [23:0], ALPHA2_COLOR_REG) is displayed.
23:0
ALPHA2_COLOR_REG (Alpha Window 1 Color Register). Specifies the color to be displayed inside Alpha Window 2
when there is a color key match in the alpha window. This is an RGB value (for RGB blending) or a YUV value (for YUV
blending). In Interlaced YUV blending mode, Y/2 value should be used.
This color is only displayed if the alpha window is enabled and bit 24 (ALPHA2_COLOR_REG_EN) is enabled.
Offset 7Ch-7Fh
31:18
Alpha Window 2 Control Register (R/W)
Reset Value: 00000000h
Reserved.
17
LOAD_ALPHA (Load Alpha Value). (Write Only) When set to 1, this bit causes the Video Processor to load the alpha
value (in bits [7:0], ALPHA2_VAL) at the start of the next frame.
16
ALPHA2_WIN_EN (Alpha Window 2 Enable). Enable bit for Alpha Window 2.
0: Disable Alpha Window 2.
1: Enable Alpha Window 2.
Note:
15:8
Valid only if video window is enabled (F4BAR0+Memory Offset 00h[0] = 1).
ALPHA2_INCR (Alpha Window 2 Increment). Specifies the alpha value increment/decrement.
This is a signed 8-bit value that is added to the alpha value for each frame. The MSB (bit 15) indicates the sign (i.e., increment or decrement). When this value reaches either the maximum or the minimum alpha value (255 or 0) it keeps that value
(i.e., it is not incremented/decremented) until it is reloaded via bit 17 (LOAD_ALPHA).
7:0
ALPHA2_VAL (Alpha Window 1 Value). Specifies the alpha value to be used for this window.
AMD Geode™ SC3200 Processor Data Book
359
Revision 5.1
Video Processor Module - Video Processor Registers - Function 4
Table 7-7. F4BAR0+Memory Offset: Video Processor Configuration Registers (Continued)
Bit
Description
Offset 80h-83h
Alpha Window 3 X Position Register (R/W)
Reset Value: 00000000h
Note:
H_TOTAL and H_SYNC_END are values programmed in the GX1 module’s Display Controller Timing registers
(GX_BASE+Memory Offset 8330h[26:19] and 8338h[10:3], respectively). The value of (H_TOTAL – H_SYNC_END) is sometimes referred to as “horizontal back porch”. For more information, see the AMD Geode™ GX1 Processor Data Book.
Note:
Desired screen position should not be outside a video window (F4BAR0+Memory Offset 08h and 0Ch).
31:27
Reserved.
26:16
ALPHA3_X_END (Alpha Window 3 Horizontal End). Determines the horizontal end position of Alpha Window 3 (not inclusive). This value is calculated according to the following formula:
Value = Desired screen position + (H_TOTAL – H_SYNC_END) – 1.
15:11
Reserved.
10:0
ALPHA3_X_START (Alpha Window 3 Horizontal Start). Determines the horizontal start position of Alpha Window 3. This
value is calculated according to the following formula:
Value = Desired screen position + (H_TOTAL – H_SYNC_END) – 2.
Offset 84h-87h
Note:
Alpha Window 3 Y Position Register (R/W)
Reset Value: 00000000h
V_TOTAL and V_SYNC_END are values programmed in the GX1 module’s Display Controller Timing registers
(GX_BASE+Memory Offset 8340h[26:16] and 8348h[26:16], respectively). The value of (V_TOTAL – V_SYNC_END) is sometimes referred to as “vertical back porch”. For more information, see the AMD Geode™ GX1 Processor Data Book.
Desired screen position should not be outside a video window (F4BAR0+Memory Offset 08h and 0Ch).
31:27
Reserved
26:16
ALPHA3_Y_END (Alpha Window 3 Vertical End). Determines the vertical end position of Alpha Window 3 (not inclusive).
This value is calculated according to the following formula:
Value = Desired screen position + (V_TOTAL – V_SYNC_END) + 2.
15:11
Reserved
10:0
ALPHA3_Y_START (Alpha Window 3 Vertical End). Determines the vertical start position of Alpha Window 3. This value
is calculated according to the following formula:
Value = Desired screen position + (V_TOTAL – V_SYNC_END) + 1.
Offset 88h-8Bh
31:25
24
Alpha Window 3 Color Register (R/W)
Reset Value: 00000000h
Reserved.
ALPHA3_COLOR_REG_EN (Alpha Window 3 Color Register Enable). Enable bit for the color key matching in Alpha
Window 3.
0: Disable. Where there is a color key match, graphics and video are alpha-blended.
1: Enable. If this bit is enabled and the alpha window is enabled, then where there is a color key match, the color value (in
bits [23:0], ALPHA3_COLOR_REG) is displayed.
23:0
ALPHA3_COLOR_REG (Alpha Window 3 Color Register). Specifies the color to be displayed inside Alpha Window 3
when there is a color key match in the alpha window. This is an RGB value (for RGB blending) or a YUV value (for YUV
blending). In Interlaced YUV blending mode, Y/2 value should be used.
This color is only displayed if the alpha window is enabled and the bit 24 (ALPHA3_COLOR_REG_EN) is enabled.
Offset 8Ch-8Fh
31:18
Alpha Window 3 Control Register (R/W)
Reset Value: 00000000h
Reserved
17
LOAD_ALPHA (Load Alpha Value). (Write Only) When set to 1, this bit causes the Video Processor to load the alpha
value (in bits [7:0], ALPHA3_VAL) at the start of the next frame.
16
ALPHA3_WIN_EN (Alpha Window 3 Enable). Enable bit for Alpha Window 3.
0: Disable Alpha Window 3.
1: Enable Alpha Window 3.
Valid only if video window is enabled (F4BAR0+Memory Offset 00h[0] = 1)
360
15:8
ALPHA3_INCR (Alpha Window 3 Increment). Specifies the alpha value increment/decrement. This is a signed 8-bit value
that is added to the alpha value for each frame. The MSB (bit 15) indicates the sign (i.e., increment or decrement). When
this value reaches either the maximum or the minimum alpha value (255 or 0) it keeps that value (i.e., it is not incremented/
decremented) until it is reloaded via bit 17 (LOAD_ALPHA).
7:0
ALPHA3_VAL (Alpha Window 3 Value). Specifies the alpha value to be used for this window.
AMD Geode™ SC3200 Processor Data Book
Video Processor Module - Video Processor Registers - Function 4
Revision 5.1
Table 7-7. F4BAR0+Memory Offset: Video Processor Configuration Registers (Continued)
Bit
Description
Offset 90h-93h
Video Request Register (R/W)
Reset Value: 001B0017h
31:28
Reserved. Set to 0.
27:16
VIDEO_X_REQ (Video Horizontal Request). Determines the horizontal (pixel) location at which to start requesting video
data out of the video FIFO. This value is calculated according to the following formula:
Value = Desired screen position + (H_TOTAL – H_SYNC_END) – 2.
15:11
Reserved
10:0
VIDEO_Y_REQ (Video Vertical Request). Determines the line number at which to start requesting video data out of the
video FIFO. This value is calculated according to the following formula:
Value = Desired screen position + (V_TOTAL – V_SYNC_END) + 1.
Offset 94h-97h
Alpha Watch Register (RO)
Reset Value: 00000000h
Alpha values may be automatically incremented/decremented for successive frames. This register can be used to read the alpha values
that are being used in the current frame.
31:24
Reserved.
23:16
ALPHA3_VAL (Value for Alpha Window 3).
15:8
ALPHA2_VAL (Value for Alpha Window 2).
7:0
ALPHA1_VAL (Value for Alpha Window 1).
Offset 98h-3FFh
Reserved
Offset 400h-403h
Video Processor Display Mode Register (R/W)
Reset Value: 00000000h
Selects various Video Processor modes.
31
Video FIFO Underflow (Empty).
0: No underflow has occurred.
1: Underflow has occurred.
Write 1 to reset this bit.
30
Video FIFO OverFlow (Full).
0: No overflow has occurred.
1: Overflow has occurred.
Write 1 to reset this bit.
29
Reserved. Write as read.
28
Reserved. Write as read.
27:4
Reserved. Set to 0.
3
Reserved. Write as read.
2
Note:
1:0
Reserved. Write as read.
VID_SEL (Video Select). Selects the source of the video data.
00: GX1 module.
10: VIP block.
01: Reserved.
11: Reserved.
The GX1 module’s video clock must be active at all times, regardless of the source of video input.
Offset 404h-407h
Reserved
Reset Value: 00000000h
Offset 408h-40Bh
Video Processor Test Mode Register (R/W)
Reset Value: 00000000h
31:0
Reserved.
Offset 40Ch-41Fh
AMD Geode™ SC3200 Processor Data Book
Reserved
361
Revision 5.1
Video Processor Module - Video Processor Registers - Function 4
Table 7-7. F4BAR0+Memory Offset: Video Processor Configuration Registers (Continued)
Bit
Description
Offset 420h-423h
31:24
GenLock Register (R/W)
Reset Value: 00000000h
Reserved. Must be set to 0.
23
ODD_TO (Odd Field Time Out). Indicates CGENTO0 (F4BAR0+Memory Offset 43Ch[15:0]) has expired. This bit can be
reset by writing 1 to it.
22
EVEN_TO (Even Field Time Out). Indicates CGENTO1 (F4BAR0+Memory Offset 43Ch[31:16]) has expired. This bit can
be reset by writing 1 to it.
21:9
Reserved.
8
Reserved. Set to 0.
7
Reserved. Set to 0.
6
Reserved. Set to 0.
5
Reserved. Set to 0.
4
GENLOCK_TOUT_EN (GenLock Timeout Enable).
0: Disable.
1: Enable timeout.
3
VIP_VSYNC_EDGE_SEL (VIP VSYNC Edge Select). Selects which edge of the VSYNC signal should be synchronized
with VIP.
0: Rising edge.
1: Falling edge.
2
GX1_VSYNC_EDGE_SEL (GX1 VSYNC Edge Select). Selects which edge of the VSYNC signal should be synchronized
with the GX1 module.
0: Rising edge.
1: Falling edge.
1
CT_GENLOCK_EN (Enable Continuous GenLock Function).
0: The continuous GenLock function is disabled.
1: Enable locking (i.e., synchronization) of the GX1 VSYNC with the VIP VSYNC on every VSYNC (i.e., continuous locking).
Note:
0
If bit 0 (SG_GENLOCK_EN) = 1, it overrides the value of this bit.
Reserved. Set to 0.
Offset 424h-427h
GenLock Delay Register (R/W)
Reset Value: 00000000h
31:21
Reserved.
20:0
GENLOCK_DEL (GenLock Delay). Indicates the delay (in 27 MHz clocks) between the VIP VSYNC and the GX1 module’s
Display Controller VSYNC.
Offset 428h-43Bh
Reserved
Offset 43Ch-43Fh
Continuous GenLock Timeout Register (R/W)
31:16
CGENTO1 (Even Field Continuous GenLock Timeout).
15:0
CGENTO0 (Odd Field Continuous GenLock Timeout).
362
Reset Value: 1FFF1FFFh
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Video Processor Module - Video Processor Registers - Function 4
7.3.2.2 VIP Support Registers - F4BAR2
F4 Index 18h, Base Address Register 2 (F4BAR2) points to
the base address of where the VIP Configuration registers
are located. Table 7-8 shows the memory mapped VIP
support registers accessed through F4BAR2.
Table 7-8. F4BAR2+Memory Offset: VIP Configuration Registers
Bit
Description
Offset 00h-03h
31:23
22
Video Interface Port Configuration Register (R/W)
Reset Value: 00000000h
Reserved. Must be set to 0.
VIP FIFO Bus Request Threshold. VIP FIFO issues a bus request when it is filled with 32 or 64 bytes.
0: 64 bytes.
1: 32 bytes
21
VBI Task B Store to Memory. When this bit is enabled, raw VBI task B data is stored to memory.
0: Disable.
1: Enable.
This bit is relevant only if bit 18 (VBI Configuration Override) = 1 (enabled).
20
VBI Task A Store to Memory. When this bit is enabled, raw VBI task A data is stored to memory.
0: Disable.
1: Enable.
This bit is relevant only if bit 18 (VBI Configuration Override) = 1 (enabled).
19
VBI Ancillary Store to Memory. When this bit is enabled, raw VBI Ancillary data is stored to memory.
0: Disable.
1: Enable.
This bit is relevant only if bit 18 (VBI Configuration Override) = 1 (enabled).
18
VBI Configuration Override. When this bit is enabled, bits [21:19] override the setup specified in bits 17 and 16.
0: Disable.
1: Enable.
17
VBI Data Task. Specifies the CCIR656 video stream task used to store raw VBI data to memory.
0: Task B.
1: Task A.
This bit is relevant only if bit 16 (VBI Mode for CCIR656) = 1 and bit 18 (VBI Configuration Override) = 0 (disabled).
16
VBI Mode for CCIR656. Specifies the mode in which to store VBI data to memory.
0: Use CCIR656 ancillary data to store VBI data to memory.
1: Use CCIR656 video task A or B to store VBI data to memory, depending on the value of bit 17 (VBI Data Task).
This bit is only used if bit 18 (VBI Configuration Override) = 0 (disabled).
15:2
Reserved. Set to 0.
1:0
Video Input Port Mode. Selects VIP operating mode.
10: CCIR656 mode.
All other decodes: Reserved.
Offset 04h-07h
31:18
17
Video Interface Control Register (R/W)
Reset Value: 00000000h
Reserved. Must be set to 0.
Line Interrupt. When asserted, allows interrupt (INTC#) generation when the Video Current Line register (F4BAR2+ Memory Offset 10h) contents equal the Video Line Target Register (F4BAR2+ Memory Offset 14h) contents.
0: Disable.
1: Enable.
16
Field Interrupt. When asserted, allows interrupt (INTC#) generation at the end of a field (i.e., the end of active video for the
current field). Interrupt generation can be enabled regardless of whether or not video capture (store to memory) is enabled.
0: Disable.
1: Enable.
15:11
Reserved. Must be set to 0.
AMD Geode™ SC3200 Processor Data Book
363
Revision 5.1
Video Processor Module - Video Processor Registers - Function 4
Table 7-8. F4BAR2+Memory Offset: VIP Configuration Registers (Continued)
Bit
Description
10
Auto-Flip. Video port operation mode.
0: The video port automatically detects the even and odd fields based on the VP_HREF and VP_VSYNC_IN signals or the
CCIR656 control codes.
1: The even/odd field detect logic is disabled and the video port automatically toggles between the even and odd buffers
during capture. The odd buffer is the first to be filled in this mode.
This bit must be programmed to 0 when Direct Video mode is used. Direct Video mode is used when VID_SEL = 10
(F4BAR0+Memory Offset 400h[1:0]). Otherwise the video select from the GX1 module. VID_SEL indicates the source of the
video data.)
9
Capture (Store to Memory) VBI Data.
0: Disable.
1: Enable.
8
Capture (Store to Memory) Video Data.
0: Disable.
1: Enable.
7:2
1:0
Reserved. Must be set to 0.
Run Mode Capture. Selects capture run mode.
00: Stop capture at end of current line.
01: Stop capture at end of current field.
10 Reserved.
11: Start capture at beginning of next field.
Offset 08h-0Bh
31:25
24
Video Interface Status Register (R/W)
Reset Value: xxxxxxxxh
Reserved. (Read Only)
Current Field. (Read Only)
0: Even field is being processed.
1: Odd field is being processed.
23:22
21
Reserved. (Read Only)
Base Register Not Updated. (Read Only) When set to 1, this bit indicates that one of the base registers (at
F4BAR2+Memory Offset 20h, 24h, 40h, and 44h) has been written but has not yet been updated.
0: All base registers are updated.
1: One or more of the base registers has not been updated.
20
FIFO Overflow Status Indication.
0: No overflow occurred.
1: An overflow occurred for the FIFO between the VIP and the Fast X-Bus.
Writing a 1 to this bit clears the status.
19:18
17
Reserved. (Read Only)
Line Interrupt (INTC#) Pending Status.
0: Interrupt not pending.
1: Interrupt pending.
Writing a 1 to this bit clears the status.
16
Field Interrupt (INTC) Pending Status.
0: Interrupt not pending.
1: Interrupt pending.
Writing a 1 to this bit clears the status.
15:10
9
Reserved. (Read Only)
VBI Data Capture Active. (Read Only)
0: VBI data is not being stored to memory.
1: VBI data is now being stored to memory.
364
AMD Geode™ SC3200 Processor Data Book
Video Processor Module - Video Processor Registers - Function 4
Revision 5.1
Table 7-8. F4BAR2+Memory Offset: VIP Configuration Registers (Continued)
Bit
8
Description
Video Data Capture Active. (Read Only)
0: Video data is not being stored to memory.
1: Video data is now being stored to memory.
7:1
0
Reserved. (Read Only)
Run Status. (Read Only)
0: Video port capture is not active.
1: Video port capture is in progress.
Offset 0Ch-0Fh
Reserved
Offset 10h-13h
Video Current Line Register (RO)
31:10
9:0
9:0
Reset Value: xxxxxxxxh
Reserved.
Current Line. Indicates the video line currently being stored to memory. The count indicated in this field is reset to 0 at the
start of each field.
Offset 14h-17h
31:10
Reset Value: 00h
Video Line Target Register (R/W)
Reset Value: 00000000h
Reserved. Must be set to 0.
Line Target. Indicates the video line to generate an interrupt on.
Offset 18h-1Bh
Reserved
Reset Value: 00000000h
Offset 1Ch-1Fh
Reserved
Reset Value: 00000000h
Offset 20h-23h
Video Data Odd Base Register (R/W)
Reset Value: 00000000h
This register specifies the base address in graphics memory where odd video field data are stored. Changes to this register take effect
at the beginning of the next field. The value in this register is 16-byte aligned.
Note:
31:0
This register is double-buffered. When a new value is written to this register, the new value is placed in a special "pending" register, and the "Base Register Not Updated" bit (F4BAR2+MemoryOffset 08h[21]) is set to 1. The Video Data Odd Base register
(this register) is not updated at this point. When the first data of the next field is stored to memory, the pending values of all
base registers (including this one) are written to the appropriate base registers, and the "Base Register Not Updated" bit is
cleared.
Video Odd Base Address. Base address where odd video data are stored in graphics memory. Bits [3:0] are always 0, and
define the required address space.
Offset 24h-27h
Video Data Even Base Register (R/W)
Reset Value: 00000000h
This register specifies the base address in graphics memory where even video field data are stored. Changes to this register take effect
at the beginning of the next field. The value in this register is 16-byte aligned.
Note:
31:0
This register is double-buffered. When a new value is written to this register, the new value is placed in a special "pending" register, and the "Base Register Not Updated" bit (F4BAR2+MemoryOffset 08h[21]) is set to 1. The Video Data Even Base register (this register) is not updated at this point. When the first data of the next field is stored to memory, the pending values of all
base registers (including this one) are written to the appropriate base registers, and the "Base Register Not Updated" bit is
cleared.
Video Even Base Address. Base address where even video data are stored in graphics memory. Bits [3:0] are always 0,
and define the required address space.
Offset 28h-2Bh
Video Data Pitch Register (R/W)
Reset Value: 00000000h
This register specifies the logical width of the video data buffer. This value is added to the start of the line address to get the address of
the next line where video data are stored to memory. This value must be an integral number of DWORDs.
31:16
Reserved.
15:0
Video Data Pitch. Specifies the logical width of the video data buffer. Bits [1:0] are always 0.
Offset 2Ch-3Fh
AMD Geode™ SC3200 Processor Data Book
Reserved
Reset Value: 00000000h
365
Revision 5.1
Video Processor Module - Video Processor Registers - Function 4
Table 7-8. F4BAR2+Memory Offset: VIP Configuration Registers (Continued)
Bit
Description
Offset 40h-43h
VBI Data Odd Base Register (R/W)
Reset Value: 00000000h
This register specifies the base address in graphics memory where VBI data for odd fields are stored. Changes to this register take
effect at the beginning of the next field. The value in this register is 16-byte aligned.
Note:
31:0
This register is double-buffered. When a new value is written this register, the new value is placed in a special "pending" register, and the "Base Register Not Updated" bit (F4BAR2+MemoryOffset 08h[21]) is set to 1. The VBI Data Odd Base Register
(this register) is not updated at this point. When the first data of the next field is stored to memory, the pending values of all
base registers (including this one) are written to the appropriate base registers, and the "Base Register Not Updated" bit is
cleared.
VBI Odd Base Address. Base address where VBI data for odd fields is stored in graphics memory. Bits [3:0] are always 0
and define the required address space.
Offset 44h-47h
VBI Data Even Base Register (R/W)
Reset Value: 00000000h
This register specifies the base address in graphics memory where VBI data for even fields is stored. Changes to this register take effect
at the beginning of the next field. The value in this register is 16-byte aligned.
Note:
31:0
This register is double-buffered. When a new value is written to this register, the new value is placed in a special "pending" register, and the "Base Register Not Updated" bit (F4BAR2+MemoryOffset 08h[21]) is set to 1. The VBI Data Even Base Register
(this register) is not updated at this point. When the first data of the next field is stored to memory, the pending values of all
base registers (including this one) are written to the appropriate base registers, and the "Base Register Not Updated" bit is
cleared.
VBI Even Base Address. Base address where VBI data for even fields is stored in graphics memory. Bits [3:0] are always
0 and define the required address space.
Offset 48h-4Bh
VBI Data Pitch Register (R/W)
Reset Value: 00000000h
This register specifies the logical width of the VBI data buffer. This value is added to the start of the line address to get the address of the
next line where VBI data are stored to memory. This value must be an integral number of DWORDs.
31:16
Reserved.
15:0
VBI Data Pitch. Specifies the logical width of the video data buffer. Bits [1:0] are always 0.
Offset 4Ch-1FFh
366
Reserved
Reset Value: 00h
AMD Geode™ SC3200 Processor Data Book
Debugging and Monitoring
Revision 5.1
8
8.0Debugging and Monitoring
8.1
Testability (JTAG)
The Test Access Port (TAP) allows board level interconnection verification and chip production tests. An IEEE1149.1a compliant test interface, TAP supports all IEEE
mandatory instructions as well as several optional instructions for added functionality. See Table 8-1 • for a summary
of all instructions support. For further information on JTAG,
refer to IEEE Standard 1149.1a-1993 Test Access Port and
Boundary-Scan Architecture.
8.1.1
Mandatory Instruction Support
The TAP supports all IEEE mandatory instructions, including:
• BYPASS.
Presents the shortest path through a given chip (a 1-bit
shift register).
• EXTEST
Drives data loaded into the JTAG path (possibly with a
SAMPLE/PRELOAD instruction) to output pins.
• SAMPLE/PRELOAD
Captures chip inputs and outputs.
8.1.2
Optional Instruction Support
The TAP supports the following IEEE optional instructions:
• IDCODE
Presents the contents of the Device Identification
register in serial format.
• CLAMP
Ensures that the Bypass register is connected between
TDI and TDO, and then drives data that was loaded into
the Boundary Scan register (e.g., via SAMPLEPRELOAD instruction) to output signals. These signals
do not change while the CLAMP instruction is selected.
• HiZ
Puts all chip outputs in inactive (floating) state
(including all pins that do not require a TRI-STATE
output for normal functionality). Note that not all pull-up
resistors are disabled in this state.
8.1.3
JTAG Chain
Balls that are not part of the JTAG chain:
• USB I/Os
Table 8-1. JTAG Mode Instruction Support
Code
Instruction
000
EXTEST
001
SAMPLE/PRELOAD
010
IDCODE
011
HIZ
100
CLAMP
101
Reserved
110
Reserved
111
BYPASS
AMD Geode™ SC3200 Processor Data Book
Activity
Drives shifted data to output pins.
Captures inputs and system outputs.
Scans out device identifier.
Puts all output and bidirectional pins in TRI-STATE.
Drives fixed data from Boundary Scan register.
Presents shortest external path through device.
367
Revision 5.1
368
Debugging and Monitoring
AMD Geode™ SC3200 Processor Data Book
Electrical Specifications
Revision 5.1
9
9.0Electrical Specifications
9.1.2
This chapter provides information about:
• General electrical specifications
Power/Ground Connections and
Decoupling
• AC characteristics
When testing and operating the SC3200, use standard
high frequency techniques to reduce parasitic effects. For
example:
All voltage values in this chapter are with respect to VSS
unless otherwise noted.
• Filter the DC power leads with low-inductance decoupling capacitors.
• DC characteristics
• Use low-impedance wiring.
9.1
General Specifications
• Utilizing the PWR and GND pins.
9.1.1
Electro Static Discharge (ESD)
9.1.3
This device is a high performance integrated circuit and is
ESD sensitive. Handling and assembly of this device
should be performed at ESD free workstations. Table 9-1
lists the ESD ratings of the SC3200.
Table 9-1. Electro Static Discharge (ESD)
Parameter
Units
Human Body Model (HBM)
2000V ESD
Machine Model (MM)
200V ESD
Absolute Maximum Ratings
Stresses beyond those indicated in the following table may
cause permanent damage to the SC3200, reduce device
reliability and result in premature failure, even when there
is no immediately apparent sign of failure. Prolonged exposure to conditions at or near the absolute maximum ratings
may also result in reduced device life span and reduced
reliability.
Note:
The values in the following table are stress ratings
only. They do not imply that operation under other
conditions is impossible.
Table 9-2. Absolute Maximum Ratings
Symbol
Parameter
Min
Max
Unit
Comments
TCASE
Operating case temperature
-10
110
o
C
Note 1
TSTORAGE
Storage temperature
-45
125
oC
Note 2
VCC
Supply voltage
See Table
9-3
V
VMAX
Voltage on
5V tolerant balls
-0.5
6.0
V
Note 3
Others
-0.5
3.6
V
Note 3, Note 4
IIK
Input clamp current
-0.5
10
mA
Note 1
IOK
Output clamp current
25
mA
Note 1
Note 1.
Note 2.
Note 3.
Note 4.
Power applied - no clocks.
No bias.
Voltage min is -0.8V with a transient voltage of 20 ns or less.
Voltage max is 4.0V with a transient voltage of 20 ns or less.
AMD Geode™ SC3200 Processor Data Book
369
Revision 5.1
9.1.4
Electrical Specifications
Operating Conditions
Table 9-3 lists the various power supplies of the SC3200 and provides the device operating conditions.
Table 9-3. Operating Conditions
Symbol
(Note 1)
Parameter
TC
Operating case temperature
AVCCUSB
Min
Typ
Max
Unit
0
-
85
Analog power supply. Powers internal analog circuits and some external signals (see
Table 9-4).
3.14
3.3
3.46
V
VBAT
Battery supply voltage. Powers RTC and
ACPI when VBAT is greater than VSB (by at
least 0.5V), and some external signals (see
Table 9-4).
2.4
3.0
3.46
V
VIO
I/O buffer power supply. Powers most of
the external signals (see Table 9-4); certain
signals within this power plane are 5V
tolerant.
3.14
3.3
3.46
V
VCORE
Core processor and internal digital power
supply. Powers internal digital logic, including internal frequency multipliers.
1.71
1.8
1.89
V
VPLL2
VPLL3
PLL. Internal Phase Locked Loops (PLL)
power supply.
3.14
3.3
3.46
V
VSB
Standby power supply. Powers RTC and
ACPI when VSB is greater than VBAT-0.5V,
and some external signals (see Table 9-4).
3.14
3.3
3.46
V
VSBL
Standby logic. Powers internal logic
needed to support Standby VSB.
1.71
1.8
1.89
V
Comments
o
C
VSBL requires a 0.1 µF bypass capacitor to
VSS.
Note 1. For VIH (Input High Voltage), VIL (Input Low Voltage), IOH (Output High Current), and IOL (Output Low Current) operating conditions refer to Section 9.2 "DC Characteristics" on page 375.
Notes:
1)
All power sources except VBAT must be connected,
even if the function is not used.
2)
VSB, and VSBL must be on if any other voltage is
applied. VSB and VBAT voltages can be applied separately. See Section 9.3.15 "Power-Up Sequencing" on
page 434.
3)
The power planes of the SC3200 can be turned on or
off. For more information, see Section 6.2.9 "Power
Management Logic" on page 174.
370
4)
It is recommended that the voltage difference between
VCORE and VSBL be less than 0.25V, in order to reduce
leakage current. If the voltage difference exceeds
0.25V, excessive leakage current is used in gates that
are connected on the boundary between voltage
domains.
5)
It is recommended that the voltage difference between
VIO and VSB be less than 0.25V, in order to reduce
leakage current. If the voltage difference exceeds
0.25V, excessive leakage current is used in gates that
are connected on the boundary between voltage
domains.
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
Table 9-4 indicates which power rails are used for each signal of the SC3200 external interface. Power planes not listed in
this table are internal, and are not related to signals of the external interface.
Table 9-4. Power Planes of External Interface Signals
VCC Balls
VSS Balls
GPWIO[0:2], LED#, ONCTL#, PWRBTN#, PWRCNT[1:2],
THRM#, CLK32, IRRX1, RI2#, SDATA_IN2
VSB
VSS
Battery
X32I, X32O
VBAT
VSS
USB
DPOS_PORT1, DNEG_PORT1, DPOS_PORT2,
DNEG_PORT2, DPOS_PORT3, DNEG_PORT3
AVCCUSB
AVSSUSB
I/O
All other external interface signals
VIO
VSS
Power Plane
Signal Names
Standby
9.1.5
DC Current
DC current is not a simple measurement. Three of the
SC3200 power states (On, Active Idle, Sleep) were
selected for measurement. For each power state measured, two functional characteristics (Typical Average,
Absolute Maximum) are used to determine how much current the SC3200 uses.
9.1.5.1 Power State Parameter Definitions
The DC characteristics tables in this section list Core and I/
O current for three of the power states. For more explanation on the SC3200 power states see Section 6.2.9 "Power
Management Logic" on page 174.
• On (C0): All internal and external clocks with respect to
the SC3200 are running and all functional blocks inside
the GX1 module (CPU Core, Memory Controller, Display
Controller, etc.) are actively generating cycles. This is
equivalent to the ACPI specification’s “S0,C0” state.
• Active Idle (C1): The CPU Core has been halted, all
other functional blocks (including the Display Controller
for refreshing the display) are actively generating cycles.
This state is entered when a HLT instruction is executed
by the CPU Core. From a user’s perspective, this state is
indistinguishable from the On state and is equivalent to
the ACPI specification’s “S0,C1” state.
• Sleep (SL2): This is the lowest power state the SC3200
can be in with voltage still applied to the device’s core
and I/O supply pins. This is equivalent to the ACPI specification’s “S1” state.
AMD Geode™ SC3200 Processor Data Book
9.1.5.2
Definition and Measurement Techniques of
SC3200 Current Parameters
These parameters describe the current while the SC3200
is in the On state:
• Typical Average: Indicates the average current used by
the SC3200 while in the On state. This is measured by
running typical Windows applications in a typical display
mode. In this case, 800x600x8 bpp at 75 Hz, 50 MHz
DCLK using a background image of vertical stripes (4pixel wide) alternating between black and white with
power management disabled (to guarantee that the
SC3200 never goes into the Active Idle state). This
number is provided for reference only since it can vary
greatly depending on the usage model of the system.
Note:
This typical average should not be confused with
the typical power numbers. Typical power is based
on a combination of On (Typical Average) and
Active Idle states.
• Absolute Maximum: Indicates the maximum instantaneous current used by the SC3200. CPU Core current is
measured by running the Landmark Speed 200 benchmark test (with power management disabled) and
measuring the peak current at any given instant during
the test. I/O current is measured by running Microsoft
Windows 98® and using a background image of vertical
stripes (1-pixel wide) alternating between black and
white at the maximum display resolution.
371
Revision 5.1
Electrical Specifications
9.1.5.3
Definition of System Conditions for
Measuring On Parameters
The SC3200’s current is highly dependent on two functional characteristics, DCLK (DOT clock) and SDRAM frequency. Table 9-5 shows how these factors are controlled
when measuring the typical average and absolute maximum processor current parameters.
9.1.5.4 DC Current Measurements
Table 9-6 and Table 9-7 show the DC current measurements of the SC3200.
Table 9-5. System Conditions Used to Measure SC3200 Current During On State
System Conditions
CPU Current Measurement
VCORE
(Note 1_
VIO
(Note 1)
DCLK
Frequency
SDRAM
Frequency
Typical Average
Nominal
Nominal
50 MHz (Note 2)
Nominal
Max
Max
135 MHz (Note 3)
Max
Absolute Maximum
Note 1. See Table 9-3 on page 370 for nominal and maximum voltages.
Note 2. A DCLK frequency of 50 MHz is derived by setting the display mode to 800x600x8 bpp at 75 Hz, using a display
image of vertical stripes (4-pixel wide) alternating between black and white with power management disabled.
Note 3. A DCLK frequency of 135 MHz is derived by setting the display mode to 1280x1024x8 bpp at 75 Hz, using a display
image of vertical stripes (1-pixel wide) alternating between black and white with power management disabled.
Table 9-6. DC Characteristics for On State
Symbol
Parameter (Note 1)
ICC3ON
ICOREON
Typ Avg
Abs Max
Unit
Comments
fCLK = 233 MHz, I/O Current @ VIO = 3.3V
(Nominal); CPU state = On
260
300
mA
ICC for VIO
fCLK = 266 MHz, I/O Current @ VIO = 3.3V
(Nominal); CPU state = On
270
310
fCLK = 233 MHz, Core Current @ VCORE =
1.8V (Nominal); CPU state = On
820
990
mA
ICC for VCORE
fCLK = 266 MHz, Core Current @ VCORE =
1.8V (Nominal); CPU state = On
900
1090
ISBON
SB Current @ VSB = 3.3V (Nominal);
CPU state = On
1
2
mA
ISBLON
SBL Current @ VSBL = 1.8V (Nominal);
CPU state = On
10
20
mA
SBL Current @ VSBL = 2.0V (Nominal);
CPU state = On
10
20
Note 1. fCLK ratings refer to internal clock frequency.
372
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
Table 9-7. DC Characteristics for Active Idle, Sleep, and Off States
Symbol
ParameterNote 1
Min
Typ
Max
ICC3IDLE
fCLK = 233 MHz, I/O Current @ VIO = 3.3V
(Nominal); CPU state = Active Idle
260
fCLK = 266 MHz, I/O Current @ VIO = 3.3V
(Nominal); CPU state = Active Idle
270
ICC3SLP
I/O Current @ VIO = 3.3V (Nominal);
CPU state = Sleep
20
ICOREIDLE
fCLK = 233 MHz, Core Current @ VCORE =
1.8V (Nominal); CPU state = Active Idle
360
fCLK = 266 MHz, Core Current @ VCORE =
1.8V (Nominal); CPU state = Active Idle
380
ICORESLP
Core Current @ VCORE = 1.8V (Nominal);
CPU state = Sleep
20
ISBOFF
SB Current @ VSB = 3.3V (Nominal);
CPU state = Off
<1
mA
ISBLOFF
SBL Current @ VSBL = 1.8V (Nominal);
CPU state = Off
<1
mA
IBAT
BAT Current @ VBAT = 3.0 (Nominal);
CPU state = Off
7
30
30
50
Unit
Comments
mA
ICC for VIO
mA
ICC for VIO,
Note 2
mA
ICC for VCORE
mA
ICC for VCORE,
Note 2
ICC for VSBL,
Note 3
µA
Note 1. fCLK ratings refer to internal clock frequency.
Note 2. All inputs are at 0.2V or VIO – 0.2 (CMOS levels). All inputs are held static, and all outputs are unloaded (static IOUT
= 0 mA).
Note 3. All VSBL supplied inputs are at 0.2V or VSBL – 0.2 (CMOS levels). All inputs are held static, and all outputs are unloaded (static IOUT = 0 mA).
9.1.6
Ball Capacitance and Inductance
Table 9-8 gives ball capacitance and inductance values.
Table 9-8. Ball Capacitance and Inductance
Symbol
Parameter
CIN
Input Pin Capacitance
CIN
Clock Input Capacitance
CIO
Min
Typ
Max
Unit
4
7
pF
Note 1
8
12
pF
Note 1
I/O Pin Capacitance
10
12
pF
Note 1
CO
Output Pin Capacitance
6
8
pF
Note 1
LPIN
Pin Inductance
20
nH
Note 2
5
Comments
Note 1. TA = 25°C, f = 1 MHz. All capacitances are not 100% tested.
Note 2. Not 100% tested.
AMD Geode™ SC3200 Processor Data Book
373
Revision 5.1
9.1.7
Electrical Specifications
Pull-Up and Pull-Down Resistors
Note:
The following table lists input balls that are internally connected to a pull-up (PU) or pull-down (PD) resistor. If these
balls are not used, they do not require connection to an
external PU or PD resistor.
The resistors described in this table are implemented as transistors. The resistance for PUs
assumes VIN = VSS and for PDs assumes VIN =
VIO.
Table 9-9. Balls with PU/PD Resistors
Ball No.
Signal Name
EBGA
TEPBGA
PU/
PD
Typ
(Note 1)
Value [Ω]
PCI
Signal Name
INIT#
FRAME#
C/BE[3:0]#
Ball No.
EBGA
TEPBGA
PU/
PD
Y3
B21
PU
Typ
(Note 1)
Value [Ω]
22.5K
E1
D8
PU
22.5K
JTAG
A8, D8,
A10, A13
H4, F3, J2,
L1
PU
22.5K
TCK
AL4
E31
PU
22.5K
TMS
AJ5
F28
PU
22.5K
PAR
C10
J4
PU
22.5K
TDI
AK5
F29
PU
22.5K
IRDY#
C8
F2
PU
22.5K
TRST#
AK4
E29
PU
22.5K
TRDY#
B8
F1
PU
22.5K
GPIO (Note 2)
STOP#
D9
G1
PU
22.5K
GPIO1
H2, AL12
D10, N30
PU
22.5K
LOCK#
C9
H3
PU
22.5K
GPIO6
AH3
D28
PU
22.5K
DEVSEL#
B5
E4
PU
22.5K
GPIO7
AH4
C30
PU
22.5K
PERR#
B9
H2
PU
22.5K
GPIO8
AJ2
C31
PU
22.5K
SERR#
A9
H1
PU
22.5K
GPIO9
AG4
C28
PU
22.5K
AJ1
B29
PU
22.5K
REQ[1:0]#
E3, C1
A5, B5
PU
22.5K
GPIO10
INTA#
AE3
D26
PU
22.5K
GPIO11
H30
AJ8
PU
22.5K
INTB#
AF1
C26
PU
22.5K
GPIO12
AJ12
N29
PU
22.5K
INTC#
H4
C9
PU
22.5K
GPIO13
AL11
M29
PU
22.5K
INTD#
B22
AA2
PU
22.5K
GPIO14
F1
D9
PU
22.5K
AJ10, AK10,
AL10, AJ11
L29, L30,
L31, M28
PU
22.5K
LDRQ
AL9
L28
PU
22.5K
SERIRQ
AL8
J31
PU
22.5K
Low Pin Count (LPC)
LAD[3:0]
System (Straps)
CLKSEL[3:0]
AL13, AK3,
B27, F3
BOOT16
TFT_PRSNT
P30, D29,
AF3, B8
PD
100K
G4
C8
PD
100K
AK13
P29
PD
100K
LPC_ROM
E4
D6
PD
100K
FPCI_MON
D3
A4
PD
100K
DID[1:0]
D2, D4
C6, C5
PD
100K
ACCESS.bus (Note 2)
AB1C
AJ13
N31
PU
22.5K
AB1D
AL12
N30
PU
22.5K
AB2C
AJ12
N29
PU
22.5K
AB2D
AL11
M29
PU
22.5K
AB2
D22
PU
22.5K
T3
D17
PUNot
e2
22.5K
PDNot
e2
22.5K
Parallel Port
AFD#/DSTRB#
PE
G3
A8
PU
22.5K
GPIO16
AL15
V31
PU
22.5K
GPIO17
J4
A10
PU
22.5K
GPIO18
A28
AG1
PU
22.5K
GPIO19
H4
C9
PU
22.5K
GPIO20
H3, AJ13
A9, N31
PU
22.5K
GPIO32
AJ11
M28
PU
22.5K
GPIO33
AL10
L31
PU
22.5K
GPIO34
AK10
L30
PU
22.5K
GPIO35
AJ10
L29
PU
22.5K
GPIO36
AL9
L28
PU
22.5K
GPIO37
AK9
K31
PU
22.5K
GPIO38
AJ9
K28
PU
22.5K
GPIO39
AL8
J31
PU
22.5K
PWRBTN#
E29
AH5
PU
100K
GPWIO[2:0]
G29, G28,
E31
AJ6, AK5,
AH6
PU
100K
F30
PD
22.5K
Power Management
Test and Measurement
GTEST
Note 1.
Note 2.
SLIN#/ASTRB#
W1
B20
PU
22.5K
STB#/WRITE#
AB1
A22
PU
22.5K
374
GPIO15
AL5
Accuracy is: 22.5 KΩ resistors are within a range of 20
KΩ to 50 KΩ. 100 KΩ resistors are within a range of 90
KΩ to 250 KΩ.
Controlled by software.
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
9.2
DC Characteristics
Table 9-10 describes the signal buffer types of the
SC3200. (See Table 3-2 "432-EBGA Ball Assignment Sorted by Ball Number" on page 29 and Table 3-4 "481TEPBGA Ball Assignment - Sorted by Ball Number" on
page 43) for each signal’s buffer type.)
The subsections that follows provide detailed DC characteristics according to buffer type.
Table 9-10. Buffer Types
Symbol
Description
Reference
Diode
Diodes only, no buffer
INAB
Input, ACCESS.bus compatible with Schmitt Trigger
Section 9.2.1
INBTN
Input, TTL compatible with Schmitt Trigger, low leakage
Section 9.2.2
INPCI
Input, PCI compatible
Section 9.2.3
Input, Strap ball (min VIH is 0.6VIO) with weak pull-down
Section 9.2.4
INT
Input, TTL compatible
Section 9.2.5
INTS
Input, TTL compatible with Schmitt Trigger type 200 mV
Section 9.2.6
INTS1
Input, with Schmitt Trigger type 200 mV
Section 9.2.7
INUSB
Input, USB compatible
Section 9.2.8
OAC97
Output, Totem-Pole, AC97 compatible
Section 9.2.9
Output, Open-Drain, capable of sinking n mA.Note 1
Section 9.2.10
Output, Open-Drain, PCI compatible
Section 9.2.11
Op/n
Output, Totem-Pole, capable of sourcing p mA and sinking n mA
Section 9.2.12
OPCI
Output, PCI compatible, TRI-STATE
Section 9.2.13
OUSB
Output, USB compatible
Section 9.2.14
TSp/n
Output, TRI-STATE, capable of sourcing p mA and sinking n mA
Section 9.2.15
WIRE
Wire, no buffer
INSTRP
ODn
ODPCI
---
---
Note 1.Output from these signals is open-drain and cannot be forced high.
AMD Geode™ SC3200 Processor Data Book
375
Revision 5.1
9.2.1
Electrical Specifications
INAB DC Characteristics
Symbol
Parameter
Min
VIH
Input High Voltage
1.4
VIL
Input Low Voltage
-0.5
(Note 1)
IIL
Input Leakage Current
VHIS
Input hysteresis
Max
Unit
Comments
V
0.8
V
10
µA
VIN = VIO
-10
µA
VIN = VSS
150
mV
Note 1. Not 100% tested.
9.2.2
INBTN DC Characteristics
Symbol
Parameter
Min
Max
Unit
VIH
Input High Voltage
2.0
VSB+0.3
(Note 1)
V
VIL
Input Low Voltage
-0.5
(Note 1)
0.8
V
IIL
Input Leakage Current
5
µA
VIN = VSB
-36
µA
VIN = VSS
VHIS
Input HysteresisNote 1
250
Comments
mV
Note 1. Not 100% tested.
9.2.3
INPCI DC Characteristics
Note that the buffer type for PCICLK (EBGA ball E2 / TEPBGA ball A7) is INT - not INPCI.
Symbol
Parameter
Min
Max
Unit
VIH
Input High Voltage
0.5VIO
VIO+0.3
(Note 1)
V
VIL
Input Low Voltage
-0.5
(Note 1)
0.3VIO
V
VIPU
Input Pull-up Voltage
lIL
Input Leakage Current
0.7VIO
+/-10
Comments
V
Note 2
µA
0 < VIN < VIO, Note 3, Note 4
Note 1. Not 100% tested.
Note 2. Not 100% tested. This parameter indicates the minimum voltage to which pull-up resistors are calculated in order
to pull a floated network.
Note 3. Input leakage currents include HiZ output leakage for all bidirectional buffers with TRI-STATE outputs.
Note 4. See Exceptions 2 and 3 in Section 9.2.15.1 on page 379.
376
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
9.2.4
INSTRP DC Characteristics
Symbol
Parameter
VIH
Input High Voltage
VIL
Input Low Voltage
IIL
Input Leakage Current
Min
Max
Unit
Comments
0.6VIO
VIO+0.3
(Note 1)
V
0.3VIO
V
36
µA
During Reset: VIN = VIO
−10
µA
VIN = VSS
Comments
Note 1. Not 100% tested.
9.2.5
INT DC Characteristics
Symbol
Parameter
Min
Max
Unit
VIH
Input High Voltage
2.0
VIO+0.3
(Note 1)
V
VIL
Input Low Voltage
-0.5
(Note 1)
0.8
V
IIL
Input Leakage Current
10
µA
VIN = VIO
−10
µA
VIN = VSS
Note 1. Not 100% tested.
9.2.6
INTS DC Characteristics
Symbol
Parameter
Min
Max
Unit
VIH
Input High Voltage
2.0
VIO+0.3
(Note 1)
V
VIL
Input Low Voltage
-0.5
(Note 1)
0.8
V
IIL
Input Leakage Current
10
µA
VIN = VIO
-10
µA
VIN = VSS
VH
Input Hysteresis
200
Comments
mV
Note 1. Not 100% tested.
9.2.7
INTS1 DC Characteristics
Symbol
Parameter
Min
Max
Unit
VIH
Input High Voltage
0.5VIO
VIO+0.3
(Note 1)
V
VIL
Input Low Voltage
-0.5
(Note 1)
0.3VIO
V
IIL
Input Leakage Current
10
µA
VIN = VIO
-10
µA
VIN = VSS
mV
Note 1
VHIS
Input Hysteresis
200
Comments
Note 1. Not 100% tested.
AMD Geode™ SC3200 Processor Data Book
377
Revision 5.1
9.2.8
Electrical Specifications
INUSB DC Characteristics
Symbol
Parameter
Min
Max
Unit
VIH
Input High Voltage
2.0
VIO+0.3
(Note 1)
V
VIL
Input Low Voltage
-0.5
(Note 1)
0.8
V
IIL
Input Leakage Current
10
µA
VIN = VIO
-10
µA
VIN = VSS
V
|(D+)-(D-)| and Figure 9-1
Includes VDI Range
VDI
Differential Input Sensitivity
0.2
VCM
Differential Common Mode
Range
0.8
2.5
V
VSE
Single Ended Receiver
Threshold
0.8
2.0
V
Comments
Note 1. Not 100% tested.
Minimum Differential Sensitivity (volts)
1.0
0.8
0.6
0.4
0.2
0.0
0.0
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2
Common Mode Input Voltage (volts)
Figure 9-1. Differential Input Sensitivity for Common Mode Range
9.2.9
OAC97 DC Characteristics
Symbol
Parameter
VOH
Output High Voltage
VOL
Output Low Voltage
9.2.10
Max
Unit
Comments
V
lOH = -5 mA
0.1VIO
V
lOL = 5 mA
Max
Unit
Comments
0.4
V
IOL = n mA
0.9VIO
ODn DC Characteristics
Symbol
Parameter
VOL
Output Low Voltage
378
Min
Min
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
9.2.11
ODPCI DC Characteristics
Symbol
Parameter
VOL
Output Low Voltage
9.2.12
Min
Unit
Comments
0.1VIO
V
Max
Unit
Comments
V
lOH = -p mA
0.4
V
lOL = n mA
Max
Unit
Comments
lOL = 1500 µA
Op/n DC Characteristics
Symbol
Parameter
Min
VOH
Output High Voltage
2.4
VOL
Output Low Voltage
9.2.13
Max
OPCI DC Characteristics
Symbol
Parameter
VOH
Output High Voltage
VOL
Output Low Voltage
9.2.14
OUSB DC Characteristics
Min
V
lOH = -500 µA
0.1VIO
V
lOL =1500 µA
0.9VIO
Symbol
Parameter
Min
Max
Unit
Comments
VUSB_OH
High-level Output Voltage
2.8
3.6
(Note 1)
V
IOH = -0.25 mA
RL = 15 KΩ to GND
VUSB_OL
Low-level Output Voltage
0.3
V
IOL = 2.5 mA
RL = 1.5 KΩ to 3.6V
tUSB_CRS
Output Signal Crossover Voltage
1.3
2.0
V
Max
Unit
Comments
V
IOH = -p mA
V
IOL = n mA
Note 1. Tested by characterization.
9.2.15
TSp/n DC Characteristics
Symbol
Parameter
Min
VOH
Output High Voltage
2.4
VOL
Output Low Voltage
0.4
9.2.15.1 Exceptions
1) IOH is valid for a GPIO pin only when it is not configured as open-drain.
V power – V IN
2)
Signals with internal pull-ups have a maximum input leakage current of: –  ---------------------------------------
R ( pull – up )
Where Vpower is VIO, or VSB.
3)
Signals with internal pull-downs have a maximum input leakage current of:
AMD Geode™ SC3200 Processor Data Book
V IN – V SS
+  ------------------------------------------
 R ( pull – down )
379
Revision 5.1
9.3
Electrical Specifications
AC Characteristics
The tables in this section list the following AC characteristics:
Table 9-11. Default Levels for Measurement of
Switching Parameters
Symbol
• Output delays
Parameter
Value (V)
• Input setup requirements
VREF
Reference Voltage
1.5
• Input hold requirements
VIHD
Input High Drive Voltage
2.0
• Output float delays
VILD
Input Low Drive Voltage
0.8
• Power-up sequencing requirements
VOHD
Output High Drive Voltage
2.4
The default levels for measurement of the rising clock edge
reference voltage (VREF), and other voltages are shown in
Table 9-11. Input or output signals must cross these levels
during testing. Unless otherwise specified, all measurement points in this section conform to these default levels.
VOLD
Output Low Drive Voltage
0.4
All AC tests are at VIO = 3.14V to 3.46V (3.3V nominal),
TC = 0 oC to 85 oC, CL = 50 pF, unless otherwise specified.
TX
CLK
VIHD
VILD
VREF
A
B
Outputs
VOHD
VOLD
Valid Output n
Max
Min
Valid Output n+1
C
Inputs
VIHD
VILD
VREF
D
VREF
Valid Input
Legend: A = Maximum Output or Float Delay Specification
B = Minimum Output or Float Delay Specification
C = Minimum Input Setup Specification
D = Minimum Input Hold Specification
Figure 9-2. Drive level and Measurement Points
380
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
9.3.1
Memory Controller Interface
The minimum input setup and hold times described in Figure 9-3 (legend C and D) define the smallest acceptable sampling
window during which a synchronous input signal must be stable to ensure correct operation.
tx
VOH
VOHD
SDCLK_OUT
SDCLK[3:0]
VREF
VOLD
VOL
A
B
Max
Min
VOH
Valid Output n
OUTPUTS
Valid Output n+1
VREF
VOL
tx
VIH
VIHD
VREF
SDCLK_IN
VILD
VIL
C
D
VIH
VREF
INPUTS
VIL
Legend: A = Maximum Output Delay
B = Minimum Output Delay
C = Minimum Input Setup
D = Minimum Input Hold
Figure 9-3. Memory Controller Drive Level and Measurement Points
AMD Geode™ SC3200 Processor Data Book
381
Revision 5.1
Electrical Specifications
Table 9-12. Memory Controller Timing Parameters
Symbol
Parameter
Min
Max
Unit
t1
Control output valid from SDCLK[3:0]
-3.0 + (x * y)
0.1 + (x * y)
ns
Note 1, Note 2
t2
MA[12:0], BA[1.0] output valid from
SDCLK[3:0]
-3.2 + (x * y)
0.1 + (x * y)
ns
Note 2
t3
MD[63.0] output valid from SDCLK[3:0]
-2.2 + (x * y)
0.7 + (x * y)
ns
Note 2
t4
MD[63.0] read data in setup to SDCLK_IN
1.3
ns
t5
MD[63:0] read data hold to SDCLK_IN
2.0
ns
t6
SDCLK[3:0], SDCLK_OUT cycle time
233 MHz
10
14
266 MHz
8.3
13.5
ns
t7
SDCLK[3:0], SDCLK_OUT fall/rise time
between (VOLD-VOHD)
2
ns
t9
SDCLK_IN fall/rise time between
(VILD-VIHD)
2
ns
t10
SDCLK[3:0], SDCLK_OUT high time
t11
233 MHz
4.0
266 MHz
3.0
Comments
ns
SDCLK[3:0], SDCLK_OUT low time
233 MHz
4.0
266 MHz
2.5
ns
Note 1. Control output includes all the following signals: RASA#, CASA#, WEA#, CKEA, DQM[7:0], and CS[1:0]#.
Load = 50 pF, VCORE = 1.8V@ 233/266 MHz, VIO = 3.3V, @25oC.
Note 2. Use the Min/Max equations [value+(x * y)] to calculate the actual output value.
x is the shift value which is applied to the SHFTSDCLK field, and y is 0.45 the core clock period.
Note that the SHFTSDCLK field = GX_BASE+Memory Offset 8404h[5:3]. Refer to the AMD Geode™ GX1 Processor Data Book for more information.
For example, for a 266 MHz SC3200 running a 88.7 MHz SDRAM clock, with a shift value of 3:
t1 Min = -3 + (3 * (3.76 * 0.45)) = 2.08 ns
t1 Max = 0.1 + (3 * (3.76 * 0.45)) = 5.18 ns
382
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
t6
t10
t1, t2, t3
t11
VOHD
VREF
VOLD
SDCLK[3:0]
t7
Control Output, MA[12:0]
BA[1:0], MD[63:0]
t7
VREF
Figure 9-4. Memory Controller Output Valid Timing Diagram
VIHD
VREF
VILD
SDCLK_IN
t9
t4
t5
MD[63:0]
Data Valid
t4
t9
t5
Data Valid
Read Data In
Figure 9-5. Read Data In Setup and Hold Timing Diagram
AMD Geode™ SC3200 Processor Data Book
383
Revision 5.1
9.3.2
Electrical Specifications
Video Port
Table 9-13. Video Input Port Timing Parameters
Symbol
Parameter
Min
Max
Unit
tVP_C
VPCKIN cycle time
18
ns
tVP_S
Video Port input setup time before
VPCKIN rising edge
6
ns
tVP_H
Video Port input hold time after VPCKIN
rising edge
0
ns
tVPCK_FR
VPCKIN fall/rise time
-
tVPCK_D
VPCKIN duty cycle
2
ns
35/65
Comments
Note 1
%
Note 1. Guaranteed by characterization.
tVP_C
VIHD
VREF
VPCKIN
VILD
tPCK_FR
tPCK_FR
tVP_S
tVP_H
VPD[7:0]
Figure 9-6. Video Input Port Timing Diagram
384
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
9.3.3
TFT Interface
Table 9-14. TFT Timing Parameters
Symbol
Parameter
Min
Max
Unit
tOV
TFTD[17:0], TFTDE valid time after
TFTDCK rising edge (multiplexed on IDE)
0
8
ns
tOV
TFTD[17:0], TFTDE valid time after
TFTDCK rising edge (multiplexed on
Parallel Port)
0
4
ns
tCLK_RF
TFTDCK rise/fall time between 0.8V and
2.0V
3
ns
tCLK_P
TFTDCK period time (multiplexed on IDE)
tCLK_P
TFTDCK period time (multiplexed on
Parallel Port)
tCLK_D
TFTDCK duty cycle
25
ns
12.5
ns
40/60
Comments
Note 1
%
Note 1. Guaranteed by characterization
tCLK_P
tOV
TFTDCK
tCLK_RF
TFTD[17:0]
TFTDE
Figure 9-7. TFT Timing Diagram
AMD Geode™ SC3200 Processor Data Book
385
Revision 5.1
9.3.4
Electrical Specifications
ACCESS.bus Interface
The following tables describe the timing for the ACCESS.bus signals.
Notes: 1) All ACCESS.bus timing is not 100% tested.
2) In this table tCLK = 1/24MHz = 41.7 ns.
Table 9-15. ACCESS.bus Input Timing Parameters
Symbol
Parameter
Min
Max
Unit
Comments
tBUFi
Bus free time between
Stop and Start condition
tSCLhigho
tCSTOsi
AB1C/AB2C setup time
8 * tCLK - tSCLri
Before Stop condition
tCSTRhi
AB1C/AB2C hold time
8 * tCLK - tSCLri
After Start condition
tCSTRsi
AB1C/AB2C setup time
8 * tCLK - tSCLri
Before Start condition
tDHCsi
Data high setup time
2 * tCLK
Before AB1C/AB2C rising edge
tDLCsi
Data low setup time
2 * tCLK
Before AB1C/AB2C rising edge
tSCLfi
AB1D/AB2D fall time
300
ns
tSCLri
AB1D/AB2D rise time
1
µs
tSCLlowi
AB1C/AB2C low time
16 * tCLK
After AB1C/AB2C falling edge
tSCLhighi
AB1C/AB2C high time
16 * tCLK
After AB1C/AB2C rising edge
tSDAfi
AB1D/AB2D fall time
300
ns
tSDAri
AB1D/AB2D rise time
1
µs
tSDAhi
AB1D/AB2D hold time
0
tSDAsi
AB1D/AB2D setup time
2 * tCLK
After AB1C/AB2C falling edge
Before AB1C/AB2C rising edge
Table 9-16. ACCESS.bus Output Timing Parameters
Symbol
Parameter
tSCLhigho
AB1C/AB2C high time
K * tCLK - 1 µs
After AB1C/AB2C rising edge,
Note 1
tSCLlowo
AB1C/AB2C low time
K * tCLK - 1 µs
After AB1C/AB2C falling edge
tBUFo
Bus free time between
Stop and Start condition
tSCLhigho
1
µs
Note 2
tCSTOso
AB1C/AB2C setup time
tSCLhigho
1
µs
Before Stop condition, Note 2
tCSTRho
AB1C/AB2C hold time
tSCLhigho
1
µs
After Start condition, Note 2
tCSTRso
AB1C/AB2C setup time
tSCLhigho
1
µs
Before Start condition, Note 2
tDHCso
Data high setup time
tSCLhigho - tSDAro
1
µs
Before AB1C/AB2C rising
edge, Note 2
tDLCso
Data low setup time
tSCLhigho - tSDAfo
1
µs
Before AB1C/AB2C rising
edge, Note 2
tSCLfo
AB1D/AB2D signal fall
time
300
ns
tSCLro
AB1D/AB2D signal rise
time
1
µs
386
Min
Max
Unit
Comments
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
Table 9-16. ACCESS.bus Output Timing Parameters (Continued)
Symbol
Parameter
tSDAfo
Min
Max
Unit
AB1D/AB2D signal fall
time
300
ns
tSDAro
AB1D/AB2D signal rise
time
1
µs
tSDAho
AB1D/AB2D hold time
tSDAvo
AB1D/AB2D valid time
7 * tCLK - tSCLfo
Comments
After AB1C/AB2C falling edge
7 * tCLK + tRD
After AB1C/AB2C falling edge
Note 1. K is determined by bits [7:1] of the ACBCTL2 register (LDN 05h/06h, Offset 05h).
Note 2. tSCLhigho value depends on the signal capacitance and the pull-up value of the relevant pin.
AB1D
AB2D
0.7VIO
0.7VIO
0.3VIO
0.3VIO
tSDAr
AB1C
tSDAf
0.7VIO
0.7VIO
0.3VIO
0.3VIO
AB2C
tSCLr
tSCLf
Figure 9-8. ACB Signals: Rising Time and Falling Timing Diagram
Start Condition
Stop Condition
AB1D
AB2D
tDLCs
tDLCo
AB1C
AB2C
tCSTOsi
tCSTOso
tBUFi
tBUFo
tCSTRhi
tCSTRho
Figure 9-9. ACB Start and Stop Condition Timing Diagram
AMD Geode™ SC3200 Processor Data Book
387
Revision 5.1
Electrical Specifications
Start Condition
AB1D
AB2D
AB1C
AB2C
tDHCsi
tDHCso
tCSTRsi
tCSTRso
tCSTRhi
tCSTRho
Figure 9-10. ACB Start Condition Timing Diagram
AB1D
AB2D
tSDAhi
tSDAho
tSDAsi
tSDAso
AB1C
AB2C
tSDAvo
tSDAho
tSCLlowi
tSCLlowo
tSCLhighi
tSCLhigho
Figure 9-11. ACB Data Bit Timing Diagram
388
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
9.3.5
PCI Bus Interface
The SC3200 is compliant with PCI Bus Rev. 2.1 specifications. Relevant information from the PCI Bus specifications
is provided below.
All parameters in Table 9-17 are not 100% tested. The
parameters in this table are further described in Figure 913.
Table 9-17. PCI AC Specifications
Symbol
Parameter
Min
IOH(AC)
(Note 1)
Switching current high
Max
Unit
Comments
-12VIO
mA
0 < VOUT ≤ 0.3VIO,
-17.1(VIO-VOUT)
mA
0.3VIO < VOUT < 0.9VIO
Equation A
(Figure 9-13)
Test point (Note 2)
IOL(AC)
(Note 1)
-32VIO
Switching current low
0.7VIO < VOUT < VIO
mA
VOUT = 0.7VIO
16VIO
mA
VIO > VOUT ≥ 0.6VIO
26.7VOUT
mA
0.6VIO > VOUT > 0.1VIO
Equation B
(Figure 9-13)
Test point (Note 2)
38VIO
0.18VIO>VOUT>0
mA
VOUT = 0.18VIO
ICL
Low clamp current
-25+(VIN+1)/0.015
mA
-3 < VIN < -1
ICH
High clamp current
25+(VIN-VIO-1)/0.015
mA
VIO+4 > VIN > VIO+1
SLEWR
(Note 3)
Output rise slew rate
1
4
V/ns
0.2VIO - 0.6VIO Load
SLEWF
Output fall slew rate
1
4
V/ns
0.6VIO - 0.2VIO Load
Note 1. Refer to the V/I curves in Figure 9-13. This specification does not apply to PCICLK0, PCICLK1, and PCIRST#
which are system outputs.
Note 2. Maximum current requirements are met when drivers pull beyond the first step voltage. Equations which define
these maximum values (A and B) are provided with relevant diagrams in Figure 9-13. These maximum values are
guaranteed by design.
Note 3. Rise slew rate does not apply to open-drain outputs. This parameter is interpreted as the cumulative edge rate
across the specified range, according to the test circuit in Figure 9-12.
Pin
0.5" max.
Output
Buffer
1 KΩ
10 pF
1 KΩ
VCC
Figure 9-12. Testing Setup for Slew Rate and Minimum Timing
AMD Geode™ SC3200 Processor Data Book
389
Revision 5.1
Electrical Specifications
Output Voltage
Volts
Output Voltage
Volts
Pull-Up
VIO
Test Point
0.9
VIO
AC
Drive Point
0.6
VIO
DC
Drive Point
DC
Drive Point
0.3
VIO
Pull-Down
AC
Drive Point
-0.5
0.5VIO
0.1
VIO
-12VIO
-48VIO
IOH mA
Test Point
1.5
16VIO
64VIO
Equation A
Equation B
IOH = (98.0/VIO)*(VOUT-VIO)*(VOUT+0.4VIO)
for VIO>VOUT>0.7VIO
IOL = (256/VIO)*VOUT*(VIO-VOUT)
for 0V<VOUT<0.18VIO
IOL mA
Figure 9-13. V/I Curves for PCI Output Signals
390
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
Table 9-18. PCI Clock Parameters
Symbol
Parameter
Min
Max
Unit
Comments
tCYC
PCICLK cycle time
30
ns
Note 1
tHIGH
PCICLK high time
11
ns
Note 2
tLOW
PCICLK low time
11
ns
Note 2
PCICLKsr
PCICLK slew Rate
1
4
V/ns
Note 3
PCIRSTsr
PCIRST# slew Rate
50
-
mV/ns
Note 4
Note 1. Clock frequency is between nominal DC and 33 MHz. Device operational parameters at frequencies under 16 MHz
are not 100% tested. The clock can only be stopped in a low state.
Note 2. Guaranteed by characterization.
Note 3. Slew rate must be met across the minimum peak-to-peak portion of the clock waveform (see Figure 9-14).
Note 4. The minimum PCIRST# slew rate applies only to the rising (de-assertion) edge of the reset signal. See Figure 9-18
for PCIRST# timing.
0.6VIO
0.5 VIO
PCICLK 0.4 VIO
0.3 VIO
0.4 VIO, p-to-p
(minimum)
0.2VIO
tLOW
tHIGH
tCYC
Figure 9-14. PCICLK Timing and Measurement Points
AMD Geode™ SC3200 Processor Data Book
391
Revision 5.1
Electrical Specifications
Table 9-19. PCI Timing Parameters
Symbol
Parameter
Min
Max
Unit
tVAL
PCICLK to signal valid delay (on the bus)
2
11
ns
Note 1, Note 2
tVAL(ptp)
PCICLK to signal valid delay (GNT#)
2
9
ns
Note 1, Note 2
tON
Float to active delay
2
ns
Note 1, Note 3,
tOFF
Active to float delay
ns
Note 1, Note 3,
tSU
Input setup time to PCICLK (on the bus)
7
ns
Note 4
tSU(ptp)
Input setup time to PCICLK (REQ#)
6
ns
Note 4
tH
Input hold time from PCICLK
0
ns
Note 4
tRST
PCIRST# active time after power stable
1
ms
Note 3, Note 5
tRST-CLK
PCIRST# active time after PCICLK stable
100
µs
Note 3, Note 5
tRST-OFF
PCIRST# active to output float delay
ns
Note 3, Note 5,
Note 6
28
40
Comments
Note 1. See the timing measurement conditions in Figure 9-16.
Note 2. Minimum times are evaluated with same load used for slew rate measurement (as shown in note 3 of Table ); maximum times are evaluated with the load circuits shown in Figure 9-15, for high-going and low-going edges respectively.
Note 3. Not 100% tested.
Note 4. See the timing measurement conditions in Figure 9-17.
Note 5. PCIRST# is asserted and de-asserted asynchronously with respect to PCICLK (see Figure 9-18).
Note 6. All output drivers are asynchronously floated when PCIRST# is active.
tVAL (Max) Rising Edge
tVAL (Max) Falling Edge
0.5" max.
Pin
0.5" max.
Output
Buffer
Output
Buffer
25 Ω
10 pF
10 pF
25 Ω
VCC
Figure 9-15. Load Circuits for Maximum Time Measurements
392
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
9.3.5.1
Measurement and Test Conditions
Table 9-20. Measurement Condition Parameters
Symbol
Value
Unit
VTH
0.6 VIO
V
Note 1
VTL
0.2 VIO
V
Note 1
VTEST
0.4 VIO
V
VSTEP (rising edge)
0.285 VIO
V
VSTEP (falling edge)
0.615 VIO
V
0.4 VIO
V
1
V/ns
VMAX
Input signal edge rate
Comments
Note 2
Note 1. The input test is performed with 0.1 VIO of overdrive. Timing parameters must not exceed this overdrive.
Note 2. VMAX specifies the maximum peak-to-peak waveform allowed for measuring input timing.
VTH
PCICLK
VTEST
VTL
tVAL
Output
Delay
VSTEP
Output Current ≤ Leakage Current
TRI-STATE
Output
tON
tOFF
Figure 9-16. Output Timing Measurement Conditions
AMD Geode™ SC3200 Processor Data Book
393
Revision 5.1
Electrical Specifications
VTH
PCICLK
VTEST
VTL
tH
tSU
VTH
VTEST
Input
Input Valid
VTEST
VMAX
VTL
Figure 9-17. Input Timing Measurement Conditions
POWER
VIO
tFAIL
PCICLK
100 ms (typ)
POR#
)(
tRST
PCIRST#
)(
tRST-CLK
tRST-OFF
PCI
Signals
Note:
TRI_STATE
The value of tFAIL is 500 ns (maximum) from the power rail which exceeds specified tolerance by more than
500 mV.
Figure 9-18. PCI Reset Timing
394
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
9.3.6
Sub-ISA Interface
All output timing is guaranteed for 50 pF load, unless otherwise specified.
The ISA Clock divisor (defined in F0 Index 50h[2:0] of the
Core Logic module) is 011.
Table 9-21. Sub-ISA Timing Parameters
Bus
Width
(Bits)
Type
Min
(ns)
Max
(ns)
Symbol
Parameter
tRD1
MEMR#/DOCR#/RD#/TRDE# read
active pulse width FE to RE
16
M
225
9-19
Standard
tRD2
MEMR#/DOCR#/RD#/TRDE# read
active pulse width FE to RE
16
M
105
9-19
Zero wait state
tRD3
IOR#/RD#/TRDE# read active pulse
width FE to RE
16
I/O
160
9-19
Standard
tRD4
IOR#/MEMR#/DOCR#/RD#/TRDE#
read active pulse width FE to RE
8
M, I/O
520
9-19
Standard
tRD5
IOR#/MEMR#/DOCR#/RD#/TRDE#
read active pulse width FE to RE
8
M, I/O
160
9-19
Zero wait state
tRCU1
MEMR#/DOCR#/RD#/TRDE#
inactive pulse width
16
M
103
9-19
tRCU2
MEMR#/DOCR#/RD#/TRDE#
inactive pulse width
8
M
163
9-19
tRCU3
IOR#/RD#/TRDE# inactive pulse
width
8, 16
I/O
163
9-19
tWR1
MEMW#/WR# write active pulse
width FE to RE
16
M
225
9-20
Standard
tWR2
MEMW#/DOCW#/WR# write active
pulse width FE to RE
16
M
105
9-20
Zero wait state
tWR3
IOW#/WR# write active pulse width
FE to RE
16
I/O
160
9-20
Standard
tWR4
IOW#/MEMW#/DOCW#/WR# write
active pulse width FE to RE
8
M, I/O
520
9-20
Standard
tWR5
IOW#/MEMW#/DOCW#/WR# write
active pulse width FE to RE
8
M, I/O
160
9-20
Zero wait state
tWCU1
MEMW#/WR#/DOCW# inactive pulse
width
16
M
103
9-20
tWCU2
MEMW#/WR#/DOCW# inactive pulse
width
8
M
163
9-20
tWCU3
IOW#/WR# inactive pulse width
8, 16
I/O
163
9-20
tRDYH
IOR#/MEMR#/RD#/DOCR#/IOW#/
MEMW#/WR#/DOCW# hold after
IOCHRDY RE
8, 16
M, I/O
120
9-19
9-20
tRDYA1
IOCHRDY valid after IOR#/MEMR#/
RD#/DOCR#/IOW#/MEMW#/WR#/
DOCW# FE
16
M, I/O
AMD Geode™ SC3200 Processor Data Book
78
Figure
Comments
9-19
9-20
395
Revision 5.1
Electrical Specifications
Table 9-21. Sub-ISA Timing Parameters (Continued)
Bus
Width
(Bits)
Type
Min
(ns)
Max
(ns)
Symbol
Parameter
tRDYA2
IOCHRDY valid after IOR#/MEMR#/
RD#/DOCR#/IOW#/MEMW#/WR#/
DOCW# FE
8
M, I/O
366
9-19
9-20
tIOCSA
IOCS[1:0]#/DOCS#/ROMCS# driven
active from A[23:0] valid
8, 16
M, I/O
34
9-19
9-20
tIOCSH
IOCS[1:0]#/DOCS#/ROMCS# valid
hold after A[23:0] invalid
8, 16
M, I/O
0
9-19
9-20
tAR1
A[23:0]/BHE# valid before MEMR#/
DOCR# active
16
M
34
9-19
tAR2
A[23:0]/BHE# valid before IOR#
active
16
I/O
100
9-19
tAR3
A[23:0]/BHE# valid before MEMR#/
DOCR#/IOR# active
8
M, I/O
100
9-19
tRA
A[23:0]/BHE# valid hold after
MEMR#/DOCR#/IOR# inactive
8, 16
M, I/O
25
9-19
tRVDS
Read data D[15:0] valid setup before
MEMR#/DOCR#/IOR# inactive
8, 16
M, I/O
24
9-19
tRDH
Read data D[15:0] valid hold after
MEMR#/DOCR#/IOR# inactive
8, 16
M, I/O
0
9-19
tHZ
Read data floating after MEMR#/
DOCR#/IOR# inactive
8, 16
M, I/O
tAW1
A[23:0]/BHE# valid before MEMW#/
DOCW# active
16
M
34
9-20
tAW2
A[23:0]/BHE# valid before IOW#
active
16
I/O
100
9-20
tAW3
A[23:0]/BHE# valid before MEMW#/
DOCW#/IOW# active
8
M, I/O
100
9-20
tWA
A[23:0]/BHE# valid hold after
MEMW#/DOCW#/IOW# invalid
8, 16
M, I/O
25
9-20
tDV1
Write data D[15:0] valid after
MEMW#/DOCW# active
8, 16
M
40
9-20
tDV2
Write data D[15:0] valid after IOW#
active
8
I/O
40
9-20
tDV3
Write data D[15:0] valid after IOW#
active
16
I/O
-23
9-20
tWTR
TRDE# inactive after MEMW#/
DOCW#/IOW# inactive
8, 16
M, I/O
20
9-20
tDH
Write data D[15:0] after MEMW#/
DOCW#/IOW# inactive
8, 16
M, I/O
45
9-20
tDF
Write data D[15:0] goes TRI-STATE
after MEMW#/DOCW#/IOW# inactive
8, 16
M, I/O
tWDAR
Write data D[15:0] after read MEMR#/
DOCR#/IOR#
8, 16
M, I/O
396
41
105
41
Figure
Comments
9-19
9-20
9-19
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
tIOCSA
tIOCSH
ROMCS#/DOCCS#
IOCS[1:0]#
Valid
A[23:0]/BHE#
tARx
IOR#/RD#/TRDE#
MEMR#/DOCR#
Valid
tRDx
tRCUx
tRA
IOW#/WR#
MEMW#/DOCW#
tRVDS
Valid Data
D[15:0]
(Read)
tRDH
tHZ
tWDAR
D[15:0]
(Write)
IOCHRDY
tRDYAx
Note:
tRDYH
x indicates a numeric index for the relevant symbol.
Figure 9-19. Sub-ISA Read Operation Timing Diagram
AMD Geode™ SC3200 Processor Data Book
397
Revision 5.1
Electrical Specifications
tIOCSA
tIOCSH
DOCCS#/ROMCS#
IOCS[1:0]#
Valid
A[23:0]/BHE#
tAWx
Valid
tWRx
IOW#/WR#
MEMW#/DOCW#
tWCUx
tWA
TRDE#
tDVx
tWTR
Valid Data
D[15:0]
tDH
tDF
IOCHRDY
tRDYAx
tRDYH
IOR#/RD#
MEMR#/DOCR#
Note:
x indicates a numeric index for the relevant symbol.
Figure 9-20. Sub-ISA Write Operation Timing Diagram
398
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
9.3.7
LPC Interface
Table 9-22. LPC and SERIRQ Timing Parameters
Symbol
Parameter
Min
Max
Unit
tVAL
Output Valid delay
0
17
ns
After PCICLK rising edge
tON
Float to Active delay
2
ns
After PCICLK rising edge
tOFF
Active to Float delay
ns
After PCICLK rising edge
tSU
Input Setup time
7
ns
Before PCICLK rising edge
tHI
Input Hold time
0
ns
After PCICLK rising edge
28
Comments
PCICLK
tVAL
tON
LPC Signals/
SERIRQ
tOFF
Figure 9-21. LPC Output Timing Diagram
PCICLK
tSU
LPC Signals/
SERIRQ
tHI
Input
Valid
Figure 9-22. LPC Input Timing Diagram
AMD Geode™ SC3200 Processor Data Book
399
Revision 5.1
9.3.8
Electrical Specifications
IDE Interface
Table 9-23. IDE General Timing Parameters
Symbol
Parameter
Min
tIDE_FALL
IDE signals fall time (from 0.9VIO to 0.1VIO)
tIDE_RISE
tIDE_RST_PW
Max
Unit
Comments
5
ns
CL = 40 pF
IDE signals rise time (from 0.1VIO to 0.9VIO)
5
ns
CL = 40 pF
IDE_RST# pulse width
25
µs
tIDE_RST_PW
IDE_RST#
Figure 9-23. IDE Reset Timing Diagram
400
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
Table 9-24. IDE Register Transfer to/from Device Timing Parameters
Mode
Symbol
Parameter
0
1
2
3
5
Unit
t0
Comments
Cycle time (min)
600
383
240
180
120
ns
t1
Address valid to IDE_IOR[0:1]#/
IDE_IOW[0:1]# setup (min)
70
50
30
30
25
ns
t2
IDE_IOR[0:1]#/IDE_IOW[0:1]# pulse
width 8-bit (min)
290
290
290
80
70
ns
Note 1
t2i
IDE_IOR[0:1]#/IDE_IOW[0:1]#
recovery time (min)
-
-
-
70
25
ns
Note 1
t3
IDE_IOW[0:1]# data setup (min)
60
45
30
30
20
ns
t4
IDE_IOW[0:1]# data hold (min)
30
20
15
10
10
ns
t5
IDE_IOR[0:1]# data setup (min)
50
35
20
20
20
ns
t6
IDE_IOR[0:1]# data hold (min)
5
5
5
5
5
ns
t6Z
IDE_IOR[0:1]# data TRI-STATE
(max)
30
30
30
30
30
ns
t9
IDE_IOR[0:1]#/IDE_IOW[0:1]# to
address valid hold (min)
20
15
10
10
10
ns
tRD
Read data valid to IDE_IORDY[0:1]
active (if IDE_IORDY[0:1] initially low
after tA (min)
0
0
0
0
0
ns
tA
IDE_IORDY[0:1] setup time
35
35
35
35
35
ns
tB
IDE_IORDY[0:1] pulse width (max)
1250
1250
1250
1250
1250
ns
tC
IDE_IORDY[0:1] assertion to release
(max)
5
5
5
5
5
ns
Note 1
Note 2
Note 3
Note 1. t0 is the minimum total cycle time, t2 is the minimum command active time, and t2i is the minimum command recovery time or command inactive time. The actual cycle time equals the sum of the command active time and the command inactive time. The three timing requirements of t0, t2, and t2i are met. The minimum total cycle time
requirements is greater than the sum of t2 and t2i. (This means that a host implementation can lengthen t2 and/or
t2i to ensure that t0 is equal to or greater than the value reported in the device’s IDENTIFY DEVICE data.)
Note 2. This parameter specifies the time from the rising edge of IDE_IOR[0:1]# to the time that the data bus is no longer
driven by the device (TRI-STATE).
Note 3. The delay from the activation of IDE_IOR[0:1]# or IDE_IOW[0:1]# until the state of IDE_IORDY[0,1] is first sampled.
If IDE_IORDY[0:1] is inactive, then the host waits until IDE_IORDY[0:1] is active before the PIO cycle is completed.
If the device is not driving IDE_IORDY[0:1] negated after activation (tA) of IDE_IOR[0:1]# or IDE_IOW[0:1]#, then
t5 is met and tRD is not applicable. If the device is driving IDE_IORDY[0:1] negated after activation (tA) of
IDE_IOR[0:1]# or IDE_IOW[0:1]#, then tRD is met and t5 is not applicable.
AMD Geode™ SC3200 Processor Data Book
401
Revision 5.1
Electrical Specifications
t0
ADDR valid1
t1
t9
t2
t2i
IDE_IOR0#
IDE_IOW0#
WRITE
IDE_DATA[7:0]
t3
t4
READ
IDE_DATA[7:0]
t5
t6
IDE_IORDY02,3
t6z
tA
IDE_IORDY02,4
tC
tRD
IDE_IORDY02,5
tB
tC
Notes:
1)
Device address consists of signals IDE_CS[0:1]# and IDE_ADDR[2:0].
2)
Negation of IDE_IORDY0,1 is used to extend the PIO cycle. The determination of whether or not the cycle is to be
extended is made by the host after tA from the assertion of IDE_IOR[0:1]# or IDE_IOW[0:1]#.
3)
Device never negates IDE_IORDY[0:1]. Device keeps IDE_IORDY[0:1] released, and no wait is generated.
4)
Device negates IDE_IORDY[0:1] before tA but causes IDE_IORDY[0:1] to be asserted before tA. IDE_IORDY[0:1] is
released, and no wait is generated.
5)
Device negates IDE_IORDY[0:1] before tA. IDE_IORDY[0:1] is released prior to negation and may be asserted for no
more than 5 ns before release. A wait is generated.
6)
The cycle completes after IDE_IORDY[0:1] is reasserted. For cycles where a wait is generated and IDE_IOR[0:1] is
asserted, the device places read data on IDE_DATA[15:0] for tRD before asserting IDE_IORDY[0:1].
Figure 9-24. Register Transfer to/from Device Timing Diagram
402
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
Table 9-25. IDE PIO Data Transfer to/from Device Timing Parameters
Mode
Symbol
Parameter
0
1
2
3
4
Unit
t0
Comments
Cycle time (min)
600
383
240
180
120
ns
t1
Address valid to IDE_IOR[0:1]#/
IDE_IOW[0:1]# setup (min)
70
50
30
30
25
ns
t2
IDE_IOR[0:1]#/IDE_IOW[0:1]# 16-bit
(min)
165
125
100
80
70
ns
Note 1
t2i
IDE_IOR[0:1]#/IDE_IOW[0:1]#
recovery time (min)
-
-
-
70
25
ns
Note 1
t3
IDE_IOW[0:1]# data setup (min)
60
45
30
30
20
ns
t4
IDE_IOW[0:1]# data hold (min)
30
20
15
10
10
ns
t5
IDE_IOR[0:1]# data setup (min)
50
35
20
20
20
ns
t6
IDE_IOR[0:1]# data hold (min)
5
5
5
5
5
ns
t6Z
IDE_IOR[0:1]# data TRI-STATE
(max)
30
30
30
30
30
ns
t9
IDE_IOR[0:1]#/IDE_IOW[0:1]# to
address valid hold (min)
20
15
10
10
10
ns
tRD
Read Data Valid to IDE_IORDY[0,1]
active (if IDE_IORDY[0:1] initially low
after tA) (min)
0
0
0
0
0
ns
tA
IDE_IORDY[0:1] Setup time
35
35
35
35
35
ns
tB
IDE_IORDY[0:1] Pulse Width (max)
1250
1250
1250
1250
1250
ns
tC
IDE_IORDY[0:1] assertion to release
(max)
5
5
5
5
5
ns
Note 1
Note 2
Note 3
Note 1. t0 is the minimum total cycle time, t2 is the minimum command active time, and t2i is the minimum command recovery time or command inactive time. The actual cycle time equals the sum of the command active time and the command inactive time. The three timing requirements of t0, t2, and t2i are met. The minimum total cycle time
requirement is greater than the sum of t2 and t2i. (This means that a host implementation may lengthen t2 and/or
t2i to ensure that t0 is equal to or greater than the value reported in the device’s IDENTIFY DEVICE data.)
Note 2. This parameter specifies the time from the rising edge of IDE_IOR[0:1]# to the time that the data bus is no longer
driven by the device (TRI-STATE).
Note 3. The delay from the activation of IDE_IOR[0:1]# or IDE_IOW[0:1]# until the state of IDE_IORDY[0:1] is first sampled.
If IDE_IORDY[0:1] is inactive, then the host waits until IDE_IORDY[0:1] is active before the PIO cycle is completed.
If the device is not driving IDE_IORDY[0:1] negated after the activation (tA) of IDE_IOR[0:1]# or IDE_IOW[0:1]#,
then t5 is met and tRD is not applicable. If the device is driving IDE_IORDY[0:1] negated after the activation (tA) of
IDE_IOR[0:1]# or IDE_IOW[0:1]#, then tRD is met and t5 is not applicable.
AMD Geode™ SC3200 Processor Data Book
403
Revision 5.1
Electrical Specifications
t0
ADDR valid1
t1
t9
t2
t2i
IDE_IOR0#
IDE_IOW0#
WRITE IDE_DATA[15:0]
t3
t4
READ IDE_DATA[15:0]
t5
t6
IDE_IORDY02,3
t6z
tA
IDE_IORDY02,4
tC
tRD
IDE_IORDY02,5
tB
tC
Notes:
1)
Device address consists of signals IDE_CS[0:1]# and IDE_ADDR[2:0].
2)
Negation of IDE_IORDY[0:1] is used to extend the PIO cycle. The determination of whether or not the cycle is to be
extended is made by the host after tA from the assertion of IDE_IOR[0:1]# or IDE_IOW[0:1]#.
3)
Device never negates IDE_IORDY[0:1]. Devices keep IDE_IORDY[0:1] released, and no wait is generated.
4)
Device negates IDE_IORDY[0:1] before tA but causes IDE_IORDY[0:1] to be asserted before tA. IDE_IORDY[0:1] is
released, and no wait is generated.
5)
Device negates IDE_IORDY[0:1] before tA. IDE_IORDY[0:1] is released prior to negation and may be asserted for no
more than 5 ns before release. A wait is generated.
6)
The cycle completes after IDE_IORDY[0:1] is reasserted. For cycles where a wait is generated and IDE_IOR[0:1]# is
asserted, the device places read data on IDE_DATA[15:0] for tRD before asserting IDE_IORDY[0:1].
Figure 9-25. PIO Data Transfer to/from Device Timing Diagram
404
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
Table 9-26. IDE Multiword DMA Data Transfer Timing Parameters
Mode
Symbol
Parameter
0
1
2
Unit
t0
Cycle time (min)
480
150
120
ns
tD
IDE_IOR[0:1]#/IDE_IOW[0:1]# (min)
215
80
70
ns
tE
IDE_IOR[0:1]# data access (max)
150
60
50
ns
tF
IDE_IOR[0:1]# data hold (min)
5
5
5
ns
tG
IDE_IOW[0:1]#/IDE_IOW[0:1]# data setup
(min)
100
30
20
ns
tH
IDE_IOW[0:1]# data hold (min)
20
15
10
ns
tI
IDE_DACK[0:1]# to IDE_IOR[0:1]#/
IDE_IOW[0:1]# setup (min)
0
0
0
ns
tJ
IDE_IOR[0:1]#/IDE_IOW[0:1]# to
IDE_DACK[0:1]# hold (min)
20
5
5
ns
tKR
IDE_IOR[0:1]# negated pulse width (min)
50
50
25
ns
tKW
IDE_IOW[0:1]# negated pulse width (min)
215
50
25
ns
tLR
IDE_IOR[0:1]# to IDE_DREQ[0:1] delay
(max)
120
40
35
ns
tLW
IDE_IOW[0:1]# to IDE_DREQ0,1 delay
(max)
40
40
35
ns
tM
IDE_CS[0:1]# valid to IDE_IOR[0:1]#/
IDE_IOW[0:1]# (min)
50
30
25
ns
tN
IDE_CS[0:1]# hold
15
10
10
ns
tZ
IDE_DACK[0:1]# to TRI-STATE
20
25
25
ns
Comments
Note 1
Note 1. t0 is the minimum total cycle time, tD is the minimum command active time, and tKR or tKW is the minimum command
recovery time or command inactive time. The actual cycle time equals the sum of the command active time and the
command inactive time. The three timing requirements of t0, tD and tKR/KW, are met. The minimum total cycle time
requirement t0 is greater than the sum of tD and tKR/KW. (This means that a host implementation can lengthen tD
and/or tKR/KW to ensure that t0 is equal to or greater than the value reported in the device’s IDENTIFY DEVICE
data.)
AMD Geode™ SC3200 Processor Data Book
405
Revision 5.1
Electrical Specifications
IDE_CS[1:0]#
tM
tN
t0
IDE_DREQ0
tL
IDE_DACK0#
tI
tD
tj
tK
IDE_IOR0#
IDE_IOW0#
tE
tZ
IDE_DATA[15:0]
tG
tF
IDE_DATA[15:0]
tG
tH
Notes:
1)
For Multiword DMA transfers, the Device may negate IDE_DREQ[0:1] within the tL specified time once IDE_DACK[0:1
is asserted, and reassert it again at a later time to resume the DMA operation. Alternatively, if the device is able to co
tinue the transfer of data, the device may leave IDE_DREQ[0:1] asserted and wait for the host to reasse
IDE_DACK[0:1]#.
2)
This signal can be negated by the host to Suspend the DMA transfer in process.
Figure 9-26. Multiword DMA Data Transfer Timing Diagram
406
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
Table 9-27. IDE UltraDMA Data Burst Timing Parameters
Mode 0
Symbol
Parameter
Min
Max
Mode 1
Min
Max
Mode 2
Min
Max
Unit
Typical sustained average two cycle time
240
160
120
ns
Two cycle time allowing for clock variations
(from rising edge to next rising edge or from
falling edge to next falling edge of STROBE)
235
156
117
ns
tCYC
Cycle time allowing for asymmetry and clock
variations (from STROBE edge to STROBE
edge)
114
75
55
ns
t2CYC
Comments
tDS
Data setup time (at recipient)
15
10
7
ns
tDH
Data hold time (at recipient)
5
5
5
ns
tDVS
Data valid setup time at sender (from data
bus being valid until STROBE edge)
70
48
34
ns
tDVH
Data valid hold time at sender (from
STROBE edge until data may become
invalid)
6
6
6
ns
tFS
First STROBE time (for device to first negate
IDE_IRDY[0:1] (DSTROBE[0:1]) from
IDE_IOW[0:1]# (STOP[0:1]) during a data in
burst)
0
230
tLI
Limited interlock time
0
150
ns
Note 1
tMLI
Interlock time with minimum
20
20
20
ns
Note 1
tUI
Unlimited interlock time
0
0
0
ns
Note 1
tAZ
Maximum time allowed for output drivers to
release (from being asserted or negated)
tZAH
Minimum delay time required for output drivers to assert or negate (from released state)
20
20
20
ns
0
0
0
ns
tENV
Envelope time (from IDE_DACK[0:1]# to
IDE_IOW[0:1]# (STOP[0:1]) and
IDE_IOR[0:1]# (HDMARDY[0:1]#) during
data out burst initiation)
20
tSR
STROBE to DMARDY time (if DMARDY# is
negated before this long after STROBE
edge, the recipient receives no more than
one additional data WORD)
50
tRFS
Ready-to-final-STROBE time (no STROBE
edges are sent this long after negation of
DMARDY#)
75
tRP
Ready-to-pause time (time that recipient
waits to initiate pause after negating
DMARDY#)
tIORDYZ
Pull-up time before allowing IDE_IORDY[0:1]
to be released
tZIORDY
Minimum time device waits before driving
IDE_IORDY[0:1]
0
0
0
ns
tACK
Setup and hold times for IDE_DACK[0:1]#
(before assertion or negation)
20
20
20
ns
tSS
Time from STROBE edge to negation of
IDE_DREQ[0:1] or assertion of
IDE_IOW[0:1]# (STOP[0:1]) (when sender
terminates a burst)
50
50
50
ns
tZAD
Note 1.
0
200
0
150
10
70
160
0
170
0
150
10
20
70
20
ns
70
ns
30
20
ns
60
50
ns
125
20
10
ns
100
20
ns
20
ns
tUI, tMLI, and tLI indicate sender-to-recipient or recipient-to-sender interlocks, that is, one agent (either sender or recipient) is waiting for the other agent to respond with a signal before proceeding. tUI is an unlimited interlock with no maximum time value. tMLI
is a limited timeout with a defined minimum. tLI is a limited time-out with a defined maximum.
AMD Geode™ SC3200 Processor Data Book
407
Revision 5.1
Electrical Specifications
All timing parameters are measured at the connector of the
device to which the parameter applies. For example, the
sender stops generating STROBE edges tRFS after the
IDE_REQ0
(device)
negation of DMARDY. Both STROBE and DMARDY timing
measurements are taken at the connector of the sender.
tUI
IDE_DACK0#
(host)
tACK
tFS
tENV
IDE_IOW0#
(STOP0)
(host)
tZAD
tENV
tACK
tFS
IDE_IOR0#
(HDMARDY0#)
(host)
tZIORDY
IDE_IRDY0 (DSTROBE0)
(device)
tAZ
tZAD
tDVS
tDVH
IDE_DATA[15:0]
IDE_ADDR[2:0]
tACK
IDE_CS[0:1]
Note:
The definitions for the IDE_IOW[0:1]# (STOP[0:1]), IDE_IOR[0:1]# (HDMARDY[0:1]#) and IDE_IRDY[0:1]
(DSTROBE[0:1]) signal lines are not in effect until IDE_REQ[0:1] and IDE_DACK[0:1]# are asserted.
Figure 9-27. Initiating an UltraDMA Data in Burst Timing Diagram
408
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
t2CYC
tCYC
tCYC
t2CYC
IDE_IRDY0
(DSTROBE0)
at device
tDVS
tDVS
tDVH
tDVH
tDVH
IDE_DATA[15:0]
at device
IDE_IRDY0
(DSTROBE0)
at host
tDH
tDS
tDH
tDS
tDH
IDE_DATA[15:0]
at host
Note:
IDE_DATA[15:0] and IDE_IRDY[0:1] (DSTROBE[0:1]) signals are shown at both the host and the device to
emphasize that cable settling time and cable propagation delay do not allow the data signals to be considered stable at the host until a certain amount of time after they are driven by the device.
Figure 9-28. Sustained UltraDMA Data In Burst Timing Diagram
AMD Geode™ SC3200 Processor Data Book
409
Revision 5.1
Electrical Specifications
IDE_DREQ0
(device)
IDE_DACK0
(host)
tRP
IDE_IOW0(STOP0)
(host)
tSR
IDE_IOR0(HDMARDY0)
(host)
tRFS
IDE_IRDY0
(DSTROBE0)
(device)
IDE_DATA[15:0]
(device)
Notes:
1)
The host can assert IDE_IOW[0:1]# (STOP[0:1]#) to request termination of the UltraDMA burst no sooner than tRP
after IDE_IOR[0:1]# (HDMARDY[0:1]#) is de-asserted.
2)
If the tSR timing is not satisfied, the host may receive up to two additional data WORDs from the device.
Figure 9-29. Host Pausing an UltraDMA Data In Burst Timing Diagram
410
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
IDE_DREQ0
(device)
tMLI
IDE_DACK0#
(host)
tLI
IDE_IOW0# (STOP0#)
(host)
tACK
tLI
tACK
tLI
IDE_IOR0# (HDMARDY0#)
(host)
tSS
tIORDZ
IDE_IRDY0
(DSTROBE0)
(device)
tZAH
tDVS
tDVH
tAZ
IDE_DATA[15:0]
(device)
CR
tACK
IDE_CS[0:1]#
IDE_ADDR[2:0]
Note:
The definitions for the IDE_IOW[0:1]# (STOP[0:1]#), IDE_IOR[0:1]# (HDMARDY[0:1]#), and IDE_IRDY[0:1]
(DSTROBE[0:1]) signal lines are no longer in effect after IDE_DREQ[0:1] and IDE_DACK[0:1]# are de-asserted.
Figure 9-30. Device Terminating an UltraDMA Data In Burst Timing Diagram
AMD Geode™ SC3200 Processor Data Book
411
Revision 5.1
Electrical Specifications
IDE_DREQ0
(device)
tLI
IDE_DACK0#
(host)
tRP
tAZ
tMLI
tACK
tZAH
IDE_IOW0#
(STOP0#)
(host)
tACK
IDE_IOR0#
(HDMARDY0#)
(host)
tRFS
tLI
tMLI
tIORDYZ
IDE_IRDY0
(DSTROBE0)
(device)
tDVS
IDE_DATA[15:0]
(device)
tDVH
CR
tACK
IDE_CS[0:1]#
IDE_ADDR[2:0]
Note:
The definitions for the IDE_IOW[0:1]# (STOP[0:1]#), IDE_IOR[0:1]# (HDMARDY[0:1]#), and IDE_IRDY[0:1]
(DSTROBE[0:1]) signal lines are no longer in effect after IDE_DREQ[0:1] and IDE_DACK[0:1] are de-asserted.
Figure 9-31. Host Terminating an UltraDMA Data In Burst Timing Diagram
412
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
IDE_DREQ0
(device)
tUI
IDE_DACK0#
(host)
tACK
tENV
IDE_IOW0#
(STOP0#)
(host)
tZIORDY
IDE_IORDY0
(DDMARDY0)
(device)
tLI
tUI
tACK
IDE_IOR0#
(HSTROBE0#)
(host)
tDVS
tDVH
IDE_DATA[15:0]
(device)
tACK
IDE_ADDR[2:0]
IDE_CS[0:1]#
Note:
The definitions for the IDE_IOW[0:1]]# (STOP[0:1]#), IDE_IORDY[0:1]# (DDMARDY[0:1]) and IDE_IOR[0:1]#
(HSTROBE[0:1]#) signal lines are not in effect until IDE_DREQ[0:1] and IDE_DACK[0:1]# are asserted.
Figure 9-32. Initiating an UltraDMA Data Out Burst Timing Diagram
AMD Geode™ SC3200 Processor Data Book
413
Revision 5.1
Electrical Specifications
t2CYC
tCYC
tCYC
IDE_IOR0#
(HSTROBE0#)
at host
t2CYC
tDVS
tDVS
tDVH
tDVH
tDVH
IDE_DATA[15:0]
at host
IDE_IOR0#
(HSTROBE0#)
at device
tDH
tDS
tDH
tDS
tDH
IDE_DATA[15:0]
at device
Note:
IDE_DATA[15:0] and IDE_IOR[0:1]# (HSTROBE[0:1]#) signals are shown at both the device and the host to
emphasize that cable settling time and cable propagation delay do not allow the data signals to be considered stable at the device until a certain amount of time after they are driven by the device.
Figure 9-33. Sustained UltraDMA Data Out Burst Timing Diagram
414
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
tRP
IDE_DREQ0
(device)
IDE_DACK0#
(host)
IDE_IOW0# (STOP0#)
(host)
tSR
IDE_IORDY0# (DDMARDY0#)
(device)
tRFS
IDE_IOR0#
(HSTROBE0#)
(host)
IDE_DATA[15:0]
(host)
Notes:
1)
The device can de-assert IDE_DREQ[0:1] to request termination of the UltraDMA burst no sooner than tRP after
IDE_IORDY[0:1]# (DDMARDY[0:1]#) is de-asserted.
2)
If the tSR timing is not satisfied, the device may receive up to two additional datawords from the host.
Figure 9-34. Device Pausing an UltraDMA Data Out Burst Timing Diagram
AMD Geode™ SC3200 Processor Data Book
415
Revision 5.1
Electrical Specifications
tLI
IDE_DREQ0
(device)
tMLI
IDE_DACK0#
(host)
IDE_IOW0#
(STOP0#)
(host)
tACK
tLI
tSS
tLI
tIORDYZ
IDE_IORDY0#
(DDMARDY0)#
(device)
tACK
IDE_IOR0#
(HSTROBE0#)
(host)
tDVH
tDVS
IDE_DATA[15:0]
(host)
CR
tACK
IDE_ADDR[2:0]
IDE_CS[0:1]#
Note:
The definitions for the IDE_IOW[0:1]# (STOP[0:1]#), IDE_IORDY[0,1]# (DDMARDY[0:1]#) and IDE_IOR[0:1]#
(HSTROBE[0:1]#) signal lines are no longer in effect after IDE_DREQ[0:1] and IDE_DACK[0:1]# are de-asserted.
Figure 9-35. Host Terminating an UltraDMA Data Out Burst Timing Diagram
416
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
IDE_DREQ0
(device)
IDE_DACK0
(host)
tLI
tACK
tMLI
IDE_IOW0# (STOP0#)
(host)
tIORDZ
tRP
IDE_IORDY0#
(DDMARDY0#)
(device)
tRFS
tLI
tMLI
tACK
IDE_IOR0#
(HSTROBE0#)
(host)
tDVS
IDE_DATA[15:0]
(host)
tDVH
CR
tACK
IDE_CS[0:1]#
IDE_ADDR[2:0]
Note:
The definitions for the IDE_IOW[0:1]# (STOP[0:1]#), IDE_IORDY[0:1]# (DDMARDY[0:1]#) and IDE_IOR[0:1]#
(HSTROBE[0:1]#) signal lines are no longer in effect after IDE_DREQ[0:1] and IDE_DACK[0:1]# are de-asserted.
Figure 9-36. Device Terminating an UltraDMA Data Out Burst Timing Diagram
AMD Geode™ SC3200 Processor Data Book
417
Revision 5.1
9.3.9
Electrical Specifications
Universal Serial Bus (USB) Interface
Table 9-28. USB Timing Parameters
Symbol
Parameter
Min
Max
Unit
Figure
Comments
Full Speed Source (Note 1, Note 2)
tUSB_R1
DPOS_Port1,2,3, DNEG_Port1,2,3
Driver Rise Time
4
20
ns
9-37
(Monotonic) from 10% to
90% of the D_Port lines
tUSB_F1
DPOS_Port1,2,3, DNEG_Port1,2,3
Driver Fall Time
4
20
ns
9-37
(Monotonic) from 90% to
10% of the D_Port lines
tUSB_FRFM
Rise/Fall time matching
90
110
%
tUSB_FSDR
Full-speed data rate
11.97
12.03
Mbps
tUSB_FSF
Full-speed frame interval
0.9995
1.0005
ms
1.0 ms ± 0.05%
tperiod_F
Full-speed period between data bits
83.1
83.5
ns
Average bit rate 12 Mbps
tUSB DOR
Driver-output resistance
28
43
W
Steady-state drive
tUSB_DJ11
Source differential driver jitter for consecutive transition
–3.5
3.5
ns
9-38
Note 3, Note 4
tUSB_DJ12
Source differential driver jitter for paired
transitions
–4.0
4.0
ns
9-38
Note 3, Note 4
tUSB_SE1
Source EOP width
160
175
ns
9-38
Note 4, Note 5
tUSB_DE1
Differential to EOP transition skew
–2
5
ns
9-39
Note 4, Note 5
tUSB_RJ11
Receiver data jitter tolerance for consecutive transition
–18.5
18.5
ns
9-40
Note 4
tUSB_RJ12
Receiver data jitter tolerance for paired
transitions
–9
9
ns
9-40
Note 4
40
ns
9-39
Note 5
ns
9-39
Note 5
Average bit rate 12 Mbps
± 0.25%
Full Speed Receiver EOP Width (Note 4)
tUSB_RE11
Must reject as EOP
tUSB_RE12
Must accept as EOP
82
Low Speed Source (Note 1)
tUSB_R2
DPOS_Port1,2,3, DNEG_Port1,2,3
Driver Rise Time
75
300
(Note 6)
ns
9-37
(Monotonic) from 10% to
90% of the D_Port lines
tUSB_F2
DPOS_Port1,2,3, DNEG_Port1,2,3
Driver Fall Time
75
300
(Note 6)
ns
9-37
(Monotonic) from 90% to
10% of the D_Port lines
tUSB_LRFM
Low-speed Rise/Fall time matching
80
120
%
tUSB_LSDR
Low-speed data rate
1.4775
1.5225
Mbps
tPERIOD_L
Low-speed period
0.657
0.677
µs
at 1.5 Mbps
tUSB_DJD21
Source differential driver jitter for consecutive transactions
–75
75
ns
Host (downstream),
Note 4
tUSB_DJD22
Source differential driver jitter for paired
transactions
–45
45
ns
9-38
Host (downstream),
Note 4
tUSB_DJU21
Source differential driver jitter for consecutive transaction
–95
95
ns
9-38
Function (downstream),
Note 4
418
Average bit rate 1.5 Mbps
± 1.5%
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
Table 9-28. USB Timing Parameters (Continued)
Symbol
Parameter
Min
Max
Unit
Figure
Comments
tUSB_DJU22
Source differential driver jitter for paired
transactions
–150
150
ns
9-38
Function (downstream),
Note 4
tUSB_SE2
Source EOP width
1.25
1.5
µs
9-39
Note 4, Note 5
tUSB_DE2
Differential to EOP transition skew
–40
100
ns
9-39
Note 5
tUSB_RJD21
Receiver data jitter tolerance for consecutive transactions
–152
152
ns
9-40
Host (upstream),
Note 4
tUSB_RJD22
Receiver data jitter tolerance for paired
transactions
–200
200
ns
9-40
Host (upstream),
Note 4
tUSB_RJU21
Receiver data jitter tolerance for consecutive transactions
–75
75
ns
9-40
Function (downstream),
Note 4
tUSB_RJU22
Receiver data jitter tolerance for paired
transactions
–45
45
ns
9-40
Function (downstream),
Note 4
330
ns
9-38
ns
9-38
Low Speed Receiver EOP Width (Note 5)
tUSB_RE21
Must reject as EOP
tUSB_RE22
Must accept as EOP
675
Note 1.
Note 2.
Note 3.
Note 4.
Note 5.
Unless otherwise specified, all timings use a 50 pF capacitive load (CL) to ground.
Full-speed timing has a 1.5 KΩ pull-up to 2.8 V on the DPOS_Port1,2,3 lines.
Timing difference between the differential data signals (DPOS_PORT1,2,3 and DNEG_PORT1,2,3).
Measured at the crossover point of differential data signals (DPOS_PORT1,2,3 and DNEG_PORT1,2,3).
EOP is the End of Packet where DPOS_PORTt = DNEG_PORT = SE0. SE0 occurs when output level voltage ≤
VSE (Min).
Note 6. CL = 350 pF.
AMD Geode™ SC3200 Processor Data Book
419
Revision 5.1
Electrical Specifications
Rise Time
CL
90%
Fall Time
90%
Differential
Data Lines
10%
10%
CL
tUSB_R1,2
tUSB_F1,2
Full Speed: 4 to 20 ns at CL = 50 pF
Low Speed: 75 ns at CL = 50 pF, 300 ns at CL = 350 pF
Figure 9-37. Data Signal Rise and Fall Timing Diagram
tUSB_DJ11
tUSB_DJD21
tUSB_DJU21
tperiod_F
tperiod_L
Crossover Points
Differential
Data Lines
(1.3-2.0) V
tUSB_DJ12
tUSB_DJD22
tUSB_DJU22
Consecutive Transitions
N*tperiod_F + tUSB_DJ11
N*tperiod_L + tUSB_DJD21
N*tperiod_L + tUSB_DJU21
Paired Transitions
N*tperiod_F + tUSB_DJ12
N*tperiod_L + tUSB_DJD22
N*tperiod_L + tUSB_DJU22
Figure 9-38. Source Differential Data Jitter Timing Diagram
420
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
tperiod_F
tperiod_L
Data
Crossover
Level
Differential
Data Lines
Differential Data to SE0 Skew
N*tperiod_F + tUSB_DE1
N*tperiod_L + tUSB_DE2
Source: tUSB_SE1, tUSB_SE2
Receiver: tUSB_RE11, tUSB_RE12
tUSB_RE21, tUSB_RE22
EOP Width
Figure 9-39. EOP Width Timing Diagram
tUSB_RJ11
tUSB_RJD21
tUSB_RJU21
tperiod_F
tperiod_L
Crossover Points
Differential
Data Lines
Consecutive Transitions
N*tperiod_F + tUSB_RJ11
N*tperiod_L + tUSB_RJD21
N*tperiod_L + tUSB_RJU21
tUSB_RJ12
tUSB_RJD22
tUSB_RJU22
Paired Transitions
N*tperiod_F + tUSB_RJ12
N*tperiod_L + tUSB_RJD22
N*tperiod_L + tUSB_RJU22
Figure 9-40. Receiver Jitter Tolerance Timing Diagram
AMD Geode™ SC3200 Processor Data Book
421
Revision 5.1
9.3.10
Electrical Specifications
Serial Port (UART)
Table 9-29. UART, Sharp-IR, SIR, and Consumer Remote Control Timing Parameters
Symbol
Parameter
tBT
Single bit time in UART and
Sharp-IR
tCMW
tCMP
tSPW
Min
Max
Unit
Comments
tBTN - 25
(Note 1)
tBTN + 25
ns
Transmitter
tBTN - 2%
tBTN + 2%
ns
Receiver
Modulation signal pulse width in
Sharp-IR and Consumer
Remote Control
tCWN - 25
(Note 2)
tCWN + 25
ns
Transmitter
ns
Receiver
Modulation signal period in
Sharp-IR and Consumer
Remote Control
tCPN - 25
(Note 3)
tCPN + 25
ns
Transmitter
tMMIN
(Note 4)
tMMAX
(Note 4)
ns
Receiver
(3/16) x tBTN - 15
(Note 1)
(3/16) x tBTN + 15
(Note 1)
ns
Transmitter, Variable
1.48
1.78
µs
Transmitter, Fixed
µs
Receiver
SIR signal pulse width
500
1
SDRT
tSJT
SIR data rate tolerance % of
nominal data rate
± 0.87%
Transmitter
± 2.0%
Receiver
SIR leading edge jitter % of
nominal bit duration
± 2.5%
Transmitter
± 6.5%
Receiver
Note 1. tBTN is the nominal bit time in UART, Sharp-IR, SIR and Consumer Remote Control modes. It is determined by the
setting of the Baud Generator Divisor registers.
Note 2. tCWN is the nominal pulse width of the modulation signal for Sharp-IR and Consumer Remote Control modes. It is
determined by the MCPW field (bits [7:5]) of the IRTXMC register and the TXHSC bit (bit 2) of the RCCFG register.
Note 3. tCPN is the nominal period of the modulation signal for Sharp-IR and Consumer Remote Control modes. It is determined by the MCFR field (bits [4:0]) of the IRTXMC registerand the TXHSC bit (bit 2) of the RCCFG register.
Note 4. tMMIN and tMMAX define the time range within which the period of the incoming subcarrier signal has to fall in order
for the signal to be accepted by the receiver. These time values are determined by the contents of register IRRXDC
and the setting of the RXHSC bit (bit 5) of the RCCFG register.
tBT
UART
tCMP
Sharp IR
Consumer
Remote
Control
tCMW
tSPW
SIR
Figure 9-41. UART, Sharp-IR, SIR, and Consumer Remote Control Timing Diagram
422
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
9.3.11
Fast IR Port
Table 9-30. Fast IR Port Timing Parameters
Symbol
Parameter
tMPW
MIR signal pulse width
Min
Max
Unit
Comments
tMWN-25
(Note 1)
tMWN+25
ns
Transmitter
ns
Receiver
60
MDRT
MIR transmitter data rate tolerance
± 0.1%
tMJT
MIR receiver edge jitter, % of
nominal bit duration
± 2.9%
tFPW
FIR signal pulse width
tFDPW
FIR signal double pulse width
120
130
ns
Transmitter
90
160
ns
Receiver
245
255
ns
Transmitter
215
285
ns
Receiver
FDRT
FIR transmitter data rate tolerance
± 0.01%
tFJT
FIR receiver edge jitter, % of
nominal bit duration
± 4.0%
Note 1. tMWN is the nominal pulse width for MIR mode. It is determined by the M_PWID field (bits [4:0]) in the MIR_PW
register at offset 01h in bank 6 of logical device 5.
tMPW
MIR
tFPW
Data
Symbol
tFDPW
FIR
Chips
Figure 9-42. Fast IR (MIR and FIR) Timing Diagram
AMD Geode™ SC3200 Processor Data Book
423
Revision 5.1
9.3.12
Electrical Specifications
Parallel Port Interface
Table 9-31. Standard Parallel Port Timing Parameters
Symbol
Parameter
Min
Typ
Max
Unit
Comments
tPDH
Port data hold
500
ns
Note 1
tPDS
Port data setup
500
ns
Note 1
tSW
Strobe width
500
ns
Note 1
Note 1. Times are system dependent and are therefore not tested.
BUSY
ACK#
tPDH
tPDS
PD[7:0]
tSW
STB#
Figure 9-43. Standard Parallel Port Typical Data Exchange Timing Diagram
424
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
Table 9-32. Enhanced Parallel Port Timing Parameters
EPP
1.9
Unit
45
x
ns
WRITE# inactive from WAIT# low
45
x
ns
tWST19a
DSTRB# or ASTRB# active from
WAIT# low
65
x
ns
tWEST
DSTRB# or ASTRB# active after
WRITE# active
10
x
x
ns
tWPDH
PD[7:0] hold after WRITE#
inactive
0
x
x
ns
tWPDS
PD[7:0] valid after WRITE#
active
x
x
ns
tEPDW
PD[7:0] valid width
80
x
x
ns
tEPDH
PD[7:0] hold after DSTRB# or
ASTRB# inactive
0
x
x
ns
Symbol
Parameter
Min
tWW19a
WRITE# active from WAIT# low
tWW19ia
Max
15
EPP
1.7
Comments
tWW19a
WRITE#
DSTRB#
or
ASTRB#
tWST19a
tWEST
tWPDH
tWST19a
PD[7:0]
tWPDS
tWW19ia
tEPDH
Valid
tEPDW
WAIT#
Figure 9-44. Enhanced Parallel Port Timing Diagram
AMD Geode™ SC3200 Processor Data Book
425
Revision 5.1
Electrical Specifications
9.3.12.1 Extended Capabilities Port (ECP)
Table 9-33. ECP Forward Mode Timing Parameters
Symbol
Parameter
Min
Max
Unit
tECDSF
Data setup before STB# active
0
ns
tECDHF
Data hold after BUSY inactive
0
ns
tECLHF
BUSY active after STB# active
75
ns
tECHHF
STB# inactive after BUSY active
0
1
s
tECHLF
BUSY inactive after STB# active
0
35
ms
tECLLF
STB# active after BUSY inactive
0
Comments
ns
tECDHF
PD[7:0]
AFD#
tECDSF
tECLLF
STB#
tECHLF
tECLHF
BUSY
tECHHF
Figure 9-45. ECP Forward Mode Timing Diagram
426
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
Table 9-34. ECP Reverse Mode Timing Parameters
Symbol
Parameter
Min
Max
Unit
tECDSR
Data setup before ACK# active
0
ns
tECDHR
Data hold after AFD# active
0
ns
tECLHR
AFD# inactive after ACK# active
75
ns
tECHHR
ACK# inactive after AFD# inactive
0
35
ms
tECHLR
AFD# active after ACK# inactive
0
1
s
tECLLR
ACK# active after AFD# active
0
Comments
ns
tECDHR
PD[7:0]
BUSY#
tECDSR
ACK#
tECLLR
tECLHR
AFD#
tECHLR
tECHHR
Figure 9-46. ECP Reverse Mode Timing Diagram
AMD Geode™ SC3200 Processor Data Book
427
Revision 5.1
9.3.13
Electrical Specifications
Audio Interface (AC97)
Table 9-35. AC Reset Timing Parameters
Symbol
Parameter
Min
Typ
Max
Unit
tRST_LOW
AC97_RST# active low pulse width
1.0
µs
tRST2CLK
AC97_RST# inactive to BIT_CLK
startup delay
162.8
ns
Comments
tRST2CLK
tRST_LOW
AC97_RST#
BIT_CLK
Figure 9-47. AC97 Reset Timing Diagram
Table 9-36. AC97 Sync Timing Parameters
Symbol
Parameter
Min
tSYNC_HIGH
SYNC active high pulse width
tSYNC_IA
SYNC inactive to BIT_CLK startup
delay
Typ
Max
1.3
Comments
µs
162.8
tSYNC_HIGH
Unit
ns
tSYNC_IA
SYNC
BIT_CLK
Figure 9-48. AC97 Sync Timing Diagram
428
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
Table 9-37. AC97 Clocks Parameters
Symbol
Parameter
Min
Typ
Max
Unit
FBIT_CLK
BIT_CLK frequency
tCLK_PD
BIT_CLK period
tCLK_J
BIT_CLK output jitter
tCLK_H
BIT_CLK high pulse width
32.56
tCLK_L
BIT_CLK low pulse width
32.56
FSYNC
SYNC frequency
48.0
KHz
tSYNC_PD
SYNC period
20.8
µs
tSYNC_H
SYNC high pulse width
1.3
µs
tSYNC_L
SYNC low pulse width
19.5
µs
FAC97_CLK
AC97_CLK frequency
24.576
MHz
tAC97_CLK_PD
AC97_CLK period
40.7
ns
tAC97_CLK_D
AC97_CLK duty cycle
45
55
%
tAC97_CLK_FR
AC97_CLK fall/rise time
2
5
ns
tAC97_CLK_J
AC97_CLK output edge-toedge jitter
100
ps
12.288
MHz
81.4
ns
Comments
750
ps
40.7
48.84
ns
Note 1
40.7
48.84
ns
Note 1
Measured from edge to edge
Note 1. Worst case duty cycle restricted to 40/60.
tCLK_L
tCLK_H
BIT_CLK
tCLK_PD
tSYNC_L
tSYNC_H
SYNC
tSYNC_PD
tAC97_CLK_PD
AC97_CLK
VOHD
VOLD
tAC97_CLK_FR
Figure 9-49. AC97 Clocks Diagram
AMD Geode™ SC3200 Processor Data Book
429
Revision 5.1
Electrical Specifications
Table 9-38. AC97 I/O Timing Parameters
Symbol
Parameter
Min
Typ
Max
tAC97_S
Input setup to falling edge of BIT_CLK
15.0
ns
tAC97_H
Hold from falling edge of BIT_CLK
10.0
ns
tAC97_OV
SDATA_OUT or SYNC valid after rising
edge of BIT_CLK
tAC97_OH
SDATA_OUT or SYNC hold time after
falling edge of BIT_CLK
tAC97_SV
Sync out valid after rising edge of
BIT_CLK
tAC97_SH
Sync out hold after falling edge of
BIT_CLK
15
5
Unit
Comments
ns
ns
15
5
ns
ns
tAC97_SV
tAC97_S
tAC97_OV
tAC97_SH
tAC97_OH
BIT_CLK
SDATA_OUT/SYNC
SDATA_IN, SDATA_IN2
tAC97_H
Figure 9-50. AC97 Data TIming Diagram
430
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
Table 9-39. AC97 Signal Rise and Fall Timing Parameters
Symbol
Parameter
Min
triseCLK
BIT_CLK rise time
tfallCLK
Typ
Max
Unit
Comments
2
6
ns
BIT_CLK fall time
2
6
ns
triseSYNC
SYNC rise time
2
6
ns
CL = 50 pF
tfallSYNC
SYNC fall time
2
6
ns
CL = 50 pF
triseDIN
SDATA_IN rise time
2
6
ns
tfallDIN
SDATA_IN fall time
2
6
ns
triseDOUT
SDATA_OUT rise time
2
6
ns
CL = 50 pF
tfallDOUT
SDATA_OUT fall time
2
6
ns
CL = 50 pF
90%
10%
BIT_CLK
triseCLK
tfallCLK
90%
10%
SYNC
triseSYNC
tfallSYNC
90%
10%
SDATA_IN
triseDIN
tfallDIN
90%
10%
SDATA_OUT
triseDOUT
tfallDOUT
Figure 9-51. AC97 Rise and Fall Timing Diagram
AMD Geode™ SC3200 Processor Data Book
431
Revision 5.1
Electrical Specifications
Table 9-40. AC97 Low Power Mode Timing Parameters
Symbol
Parameter
Min
ts2_pdown
End of Slot 2 to BIT_CLK,
SDATA_IN low
SYNC
Slot 1
Typ
Max
Unit
1.0
µs
Comments
Slot 2
BIT_CLK
SDATA_OUT
ts2_pdown
SDATA_IN
Note: BIT_CLK is not to scale
Figure 9-52. AC97 Low Power Mode Timing Diagram
432
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
9.3.14
Power Management Interface
LED# Cycle time: 1 s ± 0.1 s, 40%-60% duty cycle.
Table 9-41. PWRBTN# Timing Parameters
Symbol
Parameter
Min
tPBTNP
PWRBTN# pulse width
16
tPBTNE
Delay from PWRBTN# events to
ONCTL#
14
Max
16
Unit
Comments
ms
Note 1
ms
Note 1. Not 100% tested.
tPBTNP
PWRBTN#
tPBTNP
tPBTNE
tPBTNE
ONCTL#
Figure 9-53. PWRBTN# Trigger and ONCTL# Timing Diagram
Table 9-42. Power Management Event (GPWIO) and ONCTL# Timing Parameters
Symbol
Parameter
Min
tPM
Power management event to ONCTL#
assertion
Max
Unit
45
ns
Comments
GPWIOx
tPM
ONCTL#
PWRCNT1
PWRCNT2
Figure 9-54. GPWIO and ONCTL# Timing Diagram
AMD Geode™ SC3200 Processor Data Book
433
Revision 5.1
9.3.15
Electrical Specifications
Power-Up Sequencing
Table 9-43. Power-Up Sequence Using the Power Button Timing Parameters
Symbol
Parameter
Min
Max
Unit
t1
Voltage sequence
-100
100
ms
Optimum power-up results with
t1 = 0.
t2
PWRBTN# inactive after VSB or VSBL
applied, whichever is applied last
0
1
µs
PWRBTN# is an input and must
be powered by VSB.
t3
PWRBTN# active pulse width
16
4000
ms
If PWRBTN# max is exceeded,
ONCTL# will go inactive.
t4
ONCTL# inactive after VSB applied
0
1
ms
t5
Signal active after PWRBTN active
14
16
ms
t6
VCORE and VIO applied after ONCTL#
active
0
ms
System determines when VCORE
and VIO are applied, hence there
is no maximum constraint.
t7
POR# inactive after VCORE and VIO
applied
50
ms
POR# must not glitch during
active time.
VSBL
Comments
t1
VSB
t1
t6
VCORE
t2
VIO
t3
PWRBTN#
ONTCL#
t4
PWRCNT[2:1]
t5
t7
POR#
Figure 9-55. Power-Up Sequencing With PWRBTN# Timing Diagram
434
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
Table 9-44. Power-Up Sequence Not Using the Power Button Timing Parameters
Symbol
Parameter
Min
Max
Unit
t1
Voltage sequence
-100
100
ms
Optimum power-up results with
t1 = 0.
t2
POR# inactive after VSBL, VCORE, VSB,
and VIO applied
ms
POR# must not glitch during
active time.
t3
32KHZ startup time
VSBL, VCORE1
VSB, VIO2
50
1
s
Comments
Time required for 32 KHz oscillator and 14.318 MHz derived from
PLL6 to become stable at which
time the RTC can reliably count.
t1
t2
POR#
t3
32KHZ
1)
VSBL and VCORE should be tied together.
2)
VSB and VIO should be tied together.
Figure 9-56. Power-Up Sequencing Without PWRBTN# Timing Diagram
ACPI is non-functional and all ACPI outputs are undefined when the power-up sequence does not include using the power
button. SUSP# is an internal signal generated from the ACPI block. Without an ACPI reset, SUSP# can be permanently
asserted. If the USE_SUSP bit in CCR2 of GX1 module is enabled (Index C2h[7] = 1), the CPU will stop.
If ACPI functionality is desired, or the situation described above avoided, the power button must be toggled. This can be
done externally or internally. GPIO63 is internally connected to PWRBTN#. To toggle the power button with software,
GPIO63 must be programmed as an output using the normal GPIO programming protocol (see Section 6.4.1.1 "GPIO Support Registers" on page 240). GPIO63 must be pulsed low for at least 16 ms and not more than 4 sec.
Asserting POR# has no effect on ACPI. If POR# is asserted and ACPI was active prior to POR#, then ACPI will remain
active after POR#. Therefore, BIOS must ensure that ACPI is inactive before GPIO63 is pulsed low.
AMD Geode™ SC3200 Processor Data Book
435
Revision 5.1
9.3.16
Electrical Specifications
JTAG Interface
Table 9-45. JTAG Timing Parameters
Symbol
Parameter
Min
TCK frequency
Max
Unit
25
MHz
t1
TCK period
40
ns
t2
TCK high time
10
ns
t3
TCK low time
10
ns
t4
TCK rise time
4
ns
t5
TCK fall time
4
ns
t6
TDO valid delay
3
25
ns
t7
Non-test outputs valid delay
3
25
ns
t8
TDO float delay
30
ns
t9
Non-test outputs float delay
36
ns
t10
TDI, TMS setup time
8
ns
t11
Non-test inputs setup time
8
ns
t12
TDI, TMS hold time
7
ns
t13
Non-test inputs hold time
7
ns
Comments
50 pF load
t1
t2
VIH(Min)
1.5V
VIL(Max)
TCK
t4
t3
t5
Figure 9-57. TCK Measurement Points and Timing Diagram
436
AMD Geode™ SC3200 Processor Data Book
Revision 5.1
Electrical Specifications
TCK
t10
t12
TDI,
TMS
t6
t8
t7
t9
TDO
Output
Signals
t11
t13
Input
Signals
Figure 9-58. JTAG Test Timing Diagram
AMD Geode™ SC3200 Processor Data Book
437
Revision 5.1
438
Electrical Specifications
AMD Geode™ SC3200 Processor Data Book
Package Specifications
Revision 5.1
10
10.0Package Specifications
10.1
Thermal Characteristics
The junction-to-case thermal resistance (θJC) of the packages shown in Table 10-1 can be used to calculate the
junction (die) temperature under any given circumstance.
Table 10-1. θJC (×C/W)
Package
Max (°C/W)
EBGA
1
TEPBGA
5
A maximum junction temperature is not specified since a
maximum case temperature is. Therefore, the following
equation can be used to calculate the maximum thermal
resistance required of the thermal solution for a given maximum ambient temperature:
θCS + θSA =
TC − TA
P
where:
Note that there is no specification for maximum junction
temperature given since the operation of the device is
guaranteed to a case temperature range of 0°C to 85°C
(see Table 9-3 on page 370). As long as the case temperature of the device is maintained within this range, the junction temperature of the die will also be maintained within its
allowable operating range. However, the die (junction) temperature under a given operating condition can be calculated by using the following equation:
TJ = TC + (P * θJC)
where:
θCS = Max case-to-heatsink thermal resistance (°C/W)
allowed for thermal solution
θSA = Max heatsink-to-ambient thermal resistance (°C/W)
allowed for thermal solution
TA = Max ambient temperature (°C)
TC = Max case temperature at top center of package (°C)
P
= Maximum power dissipation (W)
If thermal grease is used between the case and heatsink,
θCS will reduce to about 0.01 °C/W. Therefore, the above
equation can be simplified to:
θCA =
TJ = Junction temperature (°C)
TC − TA
P
TC = Case temperature at top center of package (°C)
where:
P = Maximum power dissipation (W)
θJC = Junction-to-case thermal resistance (°C/W)
θCA = θSA = Max heatsink-to-ambient thermal resistance
(°C/W) allowed for thermal solution
These examples are given for reference only. The actual
value used for maximum power (P) and ambient temperature (TA) is determined by the system designer based on
system configuration, extremes of the operating environment, and whether active thermal management (via Suspend Modulation) of the GX1 module is employed.
The calculated θCA value (examples shown in Table 10-2)
represents the maximum allowed thermal resistance of the
selected cooling solution which is required to maintain the
maximum TCASE (shown in Table 9-3 on page 370) for the
application in which the device is used.
Table 10-2. Case-to-Ambient Thermal Resistance Example @ 85°C
θCA for Different Ambient Temperatures (°C/W)
Core Voltage
(VCORE)
(Nominal)
Core
Frequency
Maximum
Power (W)
20°C
25°C
30°C
35°C
40°C
1.8V
266 MHz
3.32
19.58
18.07
16.57
15.06
13.55
AMD Geode™ SC3200 Processor Data Book
439
Revision 5.1
10.1.1
Package Specifications
Heatsink Considerations
Table 10-2 on page 439 shows the maximum allowed thermal resistance of a heatsink for particular operating environments. The calculated values, defined as θCA,
represent the required ability of a particular heatsink to
transfer heat generated by the SC3200 processor from its
case into the air, thereby maintaining the case temperature
at or below 85°C. Because θCA is a measure of thermal
resistivity, it is inversely proportional to the heatsinks ability
to dissipate heat or its thermal conductivity.
Note:
A “perfect” heatsink would be able to maintain a
case temperature equal to that of the ambient air
inside the system chassis.
Looking at Table 10-2, it can be seen that as ambient temperature (TA) increases, θCA decreases, and that as power
consumption of the processor (P) increases, θCA
decreases. Thus, the ability of the heatsink to dissipate
thermal energy must increase as the processor power
increases and as the temperature inside the enclosure
increases.
While θCA is a useful parameter to calculate, heatsinks are
not typically specified in terms of a single θCA.This is
because the thermal resistivity of a heatsink is not constant
across power or temperature. In fact, heatsinks become
slightly less efficient as the amount of heat they are trying
to dissipate increases. For this reason, heatsinks are typically specified by graphs that plot heat dissipation (in
watts) vs. mounting surface (case) temperature rise above
ambient (in °C). This method is necessary because ambient and case temperatures fluctuate constantly during normal operation of the system. The system designer must be
careful to choose the proper heatsink by matching the
required θCA with the thermal dissipation curve of the
device under the entire range of operating conditions in
order to make sure that the maximum case temperature
(from Table 9-3 on page 370) is never exceeded. To
choose the proper heatsink, the system designer must
make sure that the calculated θCA falls above the curve
(shaded area). The curve itself defines the minimum temperature rise above ambient that the heatsink can maintain.
Example 1
Assume P (max) = 5W and TA (max) = 40°C.
Therefore:
θCA =
θCA =
TC − TA
P
85 − 40
5
θCA = 9
The heatsink must provide a thermal resistance below 9°C/
W. In this case, the heatsink under consideration is more
than adequate since at 5W worst case, it can limit the case
temperature rise above ambient to 40°C (θCA =8).
Example 2
Assume P (max) = 9W and TA (max) = 40°C.
Therefore:
θCA =
θCA =
TC − TA
P
85 − 40
9
θCA = 5
In this case, the heatsink under consideration is NOT adequate to limit the case temperature rise above ambient to
45°C for a 9W processor.
For more information on thermal design considerations or
heatsink properties, refer to the Product Selection Guide
of any leading vendor of thermal engineering solutions.
Note:
The power dissipations P used in these examples
are not representative of the power dissipation of
the SC3200 processor, which is always less than 4
Watts.
Mounting Surface Temperature
Rise Above Ambient – °C
Figure 10-1 is an example of a particular heatsink under
consideration
50
θCA = 45/5 = 9
40
30
θCA = 45/9 = 5
20
10
0
2
4
6
8
10
Heat Dissipated - Watts
Figure 10-1. Heatsink Example
440
AMD Geode™ SC3200 Processor Data Book
Package Specifications
10.2
Revision 5.1
Physical Dimensions
The figures in this section provide the mechanical package outlines for the 432-Terminal EBGA (Enhanced Ball Grid Array)
and 481-Terminal TEPBGA (Thermally Enhanced Ball Grid Array) packages.
NOTES: UNLESS OTHERWISE SPECIFIED.
1)
EBGA WITH LEAD (PB):
a) SOLDER BALL COMPOSITION: SN 63%, PB 37%.
b) SOLDERING PROFILE: 220o C.
2)
EBGA LEAD (PB) FREE:
a) SOLDER BALL COMPOSITION: SN 96.5%, AG 3.5%.
b) SOLDERING PROFILE: 260o C
3)
DIMENSION IS MEASURED AT THE MAXIMUM SOLDER BALL DIAMETER, PARALLEL TO PRIMARY DATUM N.
4)
REFERENCE JEDEC REGISTRATION MO-151, VARIATION -1.00, DATED JUNE 1997.
5)
THETA JUNCTION TO CASE (TJC) = 1°C/WATT.
Figure 10-2. 432-Terminal EBGA Package (Body Size: 40x40x1.72 mm; Pitch: 1.27 mm)
AMD Geode™ SC3200 Processor Data Book
441
Revision 5.1
Package Specifications
NOTES: UNLESS OTHERWISE SPECIFIED.
1)
TEPBGA WITH LEAD (PB):
a) SOLDER BALL COMPOSITION: SN 63%, PB 37%.
b) SOLDERING PROFILE: 220o C.
2)
TEPBGA LEAD (PB) FREE:
a) SOLDER BALL COMPOSITION: SN 96.5%, AG 3.5%.
b) S