SEMTECH SC338A

SC338(A)
Ultra Low Output Voltage
Dual Linear FET Controller
POWER MANAGEMENT
Description
Features
‹ ±1.5% and ±2.5% reference voltage options
The SC338(A) is an ultra low output voltage dual power
supply controller designed to simplify power management
for notebook PCs. It is part of Semtech’s Smart LDOTM
family of products. The SC338(A) has two user
adjustable outputs that can be set anywhere between
0.5V and 3.3V (VIN = 12V, anywhere between 0.5V and
1.8V for V IN = 5V) using two external resistors per
output.
available
‹ Two independant and fully adjustable outputs
‹ Wide supply voltage range permits operation from
5V or 12V rails
Very low quiescent current (500µA typical with both
outputs enabled and 5V input)
Indivdual Enable control for each output
Individual Power Good monitoring and signalling for
each output
Gate drives from input supply enable use of
N-channel MOSFETs
User selectable dropout voltage
Individual under-voltage protection for each output
MSOP-10 surface mount package
‹
‹
‹
SC338(A) features for each output include tight output
voltage regulation (±2.5% over -40°C to +85°C for
SC338, ±1.5% over 0°C to +85°C for SC338A), enable
controls, open drain power good signals, under-voltage
protection and soft start. The enable pins allow the part
to enter a very low power standby mode. Pulling them
high enables the outputs. The power good pins are open
drain and assert low when the voltage at their
respective adjust pins is below 88% (typ.) of nominal. If
the voltage at the adjust pin is below 50% (typ.) of
nominal, the under voltage protection circuitry will shut
down that output. The SC338(A) is available in an
MSOP-10 surface mount package.
‹
‹
‹
‹
Applications
‹ Notebook PCs
‹ Simple dual power supplies
Typical Application Circuit
5V or 12V IN
1.2V +/-5% IN
1.8V +/-5% IN
C1
C2
0.1uF (1)
0.1uF (1)
7
8
6
5
1
1.05V @ 3A
3
C3
C4
2
100uF, 25mOhm POSCAP
R1
R5 2k (2)
11.0k
1
2
3
1.05V Enable
4
1.05V Power Good
5
R1 

VOUT1 = 0.5 • 1 +

 R2 
Revision: November 12, 2004
1.5V @ 1.5A
Q1
IRF7311
or similar
4
U1
SC338(A)
DRV1
IN
ADJ1
DRV2
EN1
ADJ2
PGD1
GND
EN2
PGD2
R3
10
9
R6 2k (2)
20.0k
8
7
1.5V Enable
6
1.5V Power Good
R2
C5
C6
C7
R4
10.0k
10nF (2)
0.1uF
10nF (2)
10.0k
Notes:
(1) Additional capacitance may be required if far from supply
(2) Optional soft-start components
1
100uF, 25mOhm POSCAP
 R3 
VOUT 2 = 0.5 • 1 +

 R4 
www.semtech.com
SC338(A)
POWER MANAGEMENT
Absolute Maximum Ratings
PRELIMINARY
Exceeding the specifications below may result in permanent damage to the device, or device malfunction. Operation outside of the parameters
specified in the Electrical Characteristics section is not implied. Exposure to Absolute Maximum rated conditions for extended periods of time may
affect device reliability.
Parameter
Input Supply Voltage
Drive Pins
Symbol
Maximum
Units
VIN
-0.3 to +13.2
V
VDRV
-0.3 to +8.0
V
VADJ, VPGD
Adjust and Power Good Pins
-0.3 to +5.5
V
(1)
Enable Pins
V EN
-0.3 to VIN
V
Thermal Impedance Junction to Ambient
θJ A
113
°C/W
Thermal Impedance Junction to Case
θJ C
42
°C/W
Operating Ambient Temperature Range
TA
-40 to +85
°C
Operating Junction Temperature Range
TJ
-40 to +125
°C
Storage Temperature Range
TSTG
-65 to +150
°C
Lead Temperature (Soldering) 10 Sec.
TLEAD
300
°C
ESD Rating (Human Body Model)
V ESD
2
kV
Note:
(1) Or VIN, if VIN = 5V.
Electrical Characteristics
Unless specified: TA = 25°C, VIN = VEN = 5V ± 5%, VPWR(1) = 1.5V ± 5%, 0A ≤ IOUT ≤ 3A.
Values in bold apply over full operating ambient temperature range.
Parameter
Symbol
Test Conditions
Min
Typ
Max
Units
13.2
V
IN
Supply Voltage
VIN
Quiescent Current
IQ
Standby Current
IQ(OFF)
4.5
VIN = 5V
500
700
µA
VIN = 12V
600
900
µA
Both EN low
0.1
1.0
µA
Both EN low, VIN = 12V
15.0
Undervoltage Lockout
Start Threshold
VUVLO
VIN rising
3.75
V
Hysteresis
VHYST
VIN falling
0.50
V
VIH
Output on
VIL
Output off
EN
Enable Input Threshold
 2004 Semtech Corp.
2
1.3
V
0.7
www.semtech.com
SC338(A)
POWER MANAGEMENT
Electrical Characteristics (Cont.)
Unless specified: TA = 25°C, VIN = VEN = 5V ± 5%, VPWR(1) = 1.5V ± 5%, 0A ≤ IOUT ≤ 3A.
Values in bold apply over full operating ambient temperature range.
Parameter
Symbol
Test Conditions
IEN
V E N = 0V
Min
Typ
Max
Units
EN (Cont.)
Enable Input Bias Current
0
µA
VIN = VEN = 5V or 12V
-1
VADJ = 0.5V
-100
0
+100
nA
-2.5%
0.500
+2.5%
V
+1
ADJ
Adjust Input Bias Current
IADJ
Reference Voltage
V AD J
SC338A only: 0°C ≤ TA ≤ +85°C
-1.5%
+1.5%
DRV
Output Current
IDRV
Sourcing, startup
(until VTH(PGD) is reached)
10
µA
Sourcing, after startup
0.7
2.0
mA
Sinking
400
750
µA
Full On, IDRV = 0mA, VIN = 12V
6.6
6.9
V
Full On, IDRV = 0mA, VIN = 5V
4.70
4.85
VTH(UV)
Measured at ADJ pin
40
50
60
%VADJ
VTH(PGD)
Measured at ADJ pin
-15
-12
-9
%VADJ
Output Logic Low Voltage
VPGD
VADJ = 0.4V, IPGD = -1mA
0.4
V
Power Good Leakage
Current
IPGD
VADJ = 0.5V, 0V ≤ VPGD ≤ VIN
+1
µA
tr
CDRV-GND = not placed
150
CDRV-GND = 10nF
850
Output Voltage
VDRV
Under Voltage Protection
Trip Threshold
(2)
PGD
Power Good Threshold
(3)
-1
0
Soft Start
Output Rise Time
10% VOUT to 90% VOUT,
VOUT = 1.05V
µs
Notes:
(1) VPWR = input voltage to pass device drains (or sources depending upon orientation of FETs).
(2) If VTH(UV) is exceeded for longer than 50µs (nom.) the protection circuitry will shut down that output.
(3) During startup only, VTH(PGD) is -6% (typ.), then switches to -12% (typ.).
 2004 Semtech Corp.
3
www.semtech.com
SC338(A)
POWER MANAGEMENT
Pin Configuration
PRELIMINARY
Ordering Information
Top View
Part Number(1)
Output Voltage(2)
P ackag e
SC338IMSTR(3)
Both outputs adjustable
from 0.5V to 3.3V
MSOP-10
SC338IMSTRT(3)(5)
SC338AIMSTR(4)
SC338AIMSTRT(4)(5)
Notes:
(1) Only available in tape and reel packaging. A reel
contains 2500 devices.
(2) VIN = 12V (0.5V to 1.8V for VIN = 5V).
(3) VADJ is ±2.5% over -40°C ≤ TA ≤ +85°C.
(4) VADJ is ±1.5% over 0°C ≤ TA ≤ +85°C.
(5) Lead free product. This product is fully WEEE and
RoHS compliant.
(MSOP-10)
Pin Descriptions
Pin
Pin Name Pin Function
1
DRV1
Output of regulator #1. Drives the gate of an N-channel MOSFET to maintain VOUT1 set by R1 and R2.
2
A D J1
Regulator #1 sense input. Used for sensing the output voltage for power good and under-voltage, and
to set the output voltage as follows (refer to application circuit on page 1):
R1 

VOUT1 = 0.5 • 1 +

 R2 
VOUT(MAX) = 3.3V for VIN = 12V, 1.8V for VIN = 5V.
3
EN1
Active high enable control. Connect to IN if not being used. Do not allow to float.
4
PGD1
Power good signal output for VOUT1. Open drain output pulls low when VOUT1 is below (VOUT1(NOM) -12%).
5
GND
Ground.
6
PGD2
Power good signal output for VOUT2. Open drain output pulls low when VOUT2 is below (VOUT2(NOM) -12%).
7
EN2
Active high enable control. Connect to IN if not being used. Do not allow to float.
8
A D J2
Regulator #2 sense input. Used for sensing the output voltage for power good and under-voltage, and
to set the output voltage as follows (refer to application circuit on page 1):
 R3 
VOUT 2 = 0.5 • 1 +

VOUT(MAX) = 3.3V for VIN = 12V, 1.8V for VIN = 5V.
 R4 
9
DRV2
Output of regulator #2. Drives the gate of an N-channel MOSFET to maintain VOUT2 set by R3 and R4.
10
IN
 2004 Semtech Corp.
+5V or +12V supply.
4
www.semtech.com
SC338(A)
POWER MANAGEMENT
Block Diagram
(0.95 VBG
at start-up)
(0.95 VBG
at start-up)
Marking Information
SC338
SC338A
Top Mark
AK00
yyww
AK0A
338A
yyww
Bottom Mark
Bottom Mark
xxxx
xxxx
AK00:
yyww:
xxxx:
xxxx:
xxxx
xxxx
Identifier for SC338
Date code (Example: 0012)
Semtech Lot # (Example: E901
01-1)
 2004 Semtech Corp.
Top Mark
338A:
yyww:
xxxx:
xxxx:
5
Identifier for SC338A
Date code (Example: 0012)
Semtech Lot # (Example: E901
01-1)
www.semtech.com
SC338(A)
POWER MANAGEMENT
Applications Infomation
PRELIMINARY
Theory Of Operation
and 3.75mA at 12V in during normal operation. The high
side drive voltage is generated from VIN by a 7V (nominal)
low dropout regulator, thus at 12V in, 6.9V is available
and at 5V in, 4.85V is available (since the LDO will be in
dropout).
The SC338(A) dual linear FET controller provides a simple
way to drive two N-channel MOSFETs to produce tightly
regulated output voltages from one or two available,
higher, supply voltages. It takes its power from either a
5V or 12V supply, drawing typically 500µA while
operating.
At start-up, the source current available from the drive
pins is limited to 10µA (typical) until the power good
threshold is reached, at approximately 6% below
nominal output voltage. At this point the full drive
capability is enabled. With this constant current source
at start-up, it is a simple matter to use a small capacitor
on the drive pin to slow this rate of rise. The rate of rise
of the drive pin voltage will be:
It contains an internal bandgap reference which is
compared to the output voltages via resistor dividers.
These resistor dividers are external and user selectable .
Depending upon the input voltage used for the device,
the drive pin (DRV1, DRV2) can pull up to a guaranteed
minimum of 6.6V (from 12V supply) or 4.7V (from 5V
supply). Thus the device can be used to regulate a large
range of output voltages by careful selection of the
external MOSFETs (see component selection, below).
dVDRV IDRV
=
V/s
dt
CSS
A 10nF soft start capacitor will give a 1ms output rise
time for VIN = 12V and VOUT = 1.05V, for example. The
output rise time will of course depend upon the gate
threshold of the MOSFET being used. Please refer to
the Output Rise Time chart on Page 13 showing typical
output rise times. For very low ESR output capacitors
(<5mΩ) and very high soft start capacitance (>100nF),
it may be necessary to add a resistor in series with the
soft start capacitor to ensure stability. Generally,
however, this resistor is not required, as this is a very
unlikely situation.
The SC338(A) includes an active high enable control (EN1,
EN2) for each output. If this pin is pulled low, the related
drive pin is pulled low, turning off the N-channel MOSFET.
If the pin is pulled up to 1.8V ≤ VEN ≤ VIN, the drive pin will
be enabled. This pin should not be allowed to float.
Each output has a power good output (PGD1, PGD2)
which are open drain outputs that pull low if the related
output is below the power good threshold (-12% of the
programmed output voltage typical, -6% typical at startup). The power good circuitry is active if the device is
enabled, regardless of the state of the over current latch.
The power good circuitry is not active if that
particular output is disabled.
The soft start capacitance does not adversely affect
transient response since the drive current capability is
200 times higher once the device has started.
OCP and Power Supply Sequencing
Also included for each output is an overcurrent
protection circuit that monitors the output voltage. If the
output voltage drops below 50% (typ.) of nominal, as
would occur during an overcurrent or short condition, the
device will pull the drive pin low and latch off. The device
will need to have the power supply or enable pin toggled
to reset the latch condition. Each output latches
independently (i.e. if one output latches off, the other
output will function normally).
The SC338(A) has output undervoltage protection that
looks at a particular output to see if it is a) less than
50% (typical) of it’s nominal value and b) VDRV for that
output is within 350mV (typical) of maximum. If both of
these criteria are met, there is a 50µs (typical) delay and
then the output is shut down. This provides inherent
immunity to UV shutdown at start-up (which may occur
while the output capacitors are being charged) since VDRV
has a very slow rate of rise with IDRV limited to 10µA.
Drive Outputs and Soft Start
At start-up, it is necessary to ensure that the power
supplies and enables are sequenced correctly to avoid
erroneous latch-off. For UV latch-off not to occur at startup due to sequencing issues, the key is that the voltage
The drive outputs for each output are source and sink
capable. The sink current is typically 0.8mA at 5V in (1mA
at 12V in). The source current is typically 2mA at 5V in
 2004 Semtech Corp.
6
www.semtech.com
SC338(A)
POWER MANAGEMENT
Applications Infomation (Cont.)
supplied to the MOSFET drain should be greater than
the output undervoltage threshold when that
output is enabled. This assumes that the drop through
the pass MOSFET is negligible. If not, then this drop needs
to be taken into account also since:
VOUT = VDRAIN - (IOUT x RDS(ON)).
from 1.8V set for 1.5V out, output 2 not shown for
simplicity. Worst case undervoltage threshold is 60% (over
temperature) of 1.5V, or 0.9V. The typical enable
threshold is ~1V. See Figure 1 below.
If the supply to the SC338(A) IN pin comes up before the
supply to the MOSFET drain, then that output should be
enabled as the supply to the MOSFET drain is applied
- the Power Good signal for this rail would be ideal. If the
power supply to the MOSFET drain comes up before the
power supply to the SC338(A) IN pin, then the output
can either be enabled with the supply to the IN pin or
afterwards. Please see the example below.
Output Capacitors: low ESR capacitors such as Sanyo
POSCAPs or Panasonic SP-caps are recommended for
bulk capacitance, with ceramic bypass capacitors for
decoupling high frequency transients.
Input Capacitors: placement of low ESR capacitors such
as Sanyo POSCAPs or Panasonic SP-caps at the input to
the MOSFET (VDRAIN) will help to hold up the power supply
during fast load changes, thus improving overall transient
response. If VDRAIN is located at the bulk capacitors for
the upstream voltage regulator, additional capacitance
Component Selection
Example: SC338(A) powered from 5V, output 1 powered
SC338(A) Supply Comes Up Before MOSFET Drain Supply
MOSFET Drain Supply Comes Up Before SC338(A) Supply
Figure 1: Power Supply Sequencing
 2004 Semtech Corp.
7
www.semtech.com
SC338(A)
POWER MANAGEMENT
Applications Infomation (Cont.)
PRELIMINARY
may not be required. In this case a 0.1µF ceramic
capacitor will suffice. The input supply to the SC338(A)
should be bypassed with a 0.1µF ceramic capacitor.
MOSFETs: very low or low threshold N-channel MOSFETs
are required. Selecting FETs rated for VGS of 2.7V or 4.5V
will depend upon the available drive voltage (6.9V from
12V in or 4.85V from 5V in), the output voltage and
output current. For the device to work under all
operating conditions, a maximum RDS(ON) must be met to
ensure that the output will never go into dropout:
RDS( ON)(MAX ) =
VIN(MIN ) − VOUT (MAX )
IOUT (MAX )
VOUT (V)
R1 or R3 (kΩ )
R2 or R4 (kΩ )
1.05
11.0
10.0
1.2
14.0
10.0
1.5
20.0
10.0
2.5
45.3
11.3
3.3
63.4
11.3
Table 1: Recommended Resistor Values For SC338(A)
Ω
Design Example
Note that RDS(ON) must be met at all temperatures and at
the minimum VGS condition.
Goal: 1.05V±5% @ up to 2.5A from 1.2V±5% and 5V±5%
Setting The Output Voltage: the adjust pins connect
directly to the inverting input of the error amplifiers, and
the output voltage is set using external resistors (please
refer to the Typical Application Circuit on page 1).
Solution 1: no passive droop.
Total window for DC error, ripple and transient is ±52.5mV
Since this device is linear, and assuming that it has been
designed to not ever enter dropout, we do not have ripple
on the output.
Using output 1 as an example, the output voltage can
be calculated as follows:
R1 

VOUT = 0.5 • 1 +

 R2 
The input bias current for the adjust pin is so low that it
can be safely ignored. To avoid picking up noise, it is
recommended that the total resistance of the feedback
chain be less than 100kΩ.
The DC error for this output is the sum of:
VREF accuracy = ±2.5% = ±26.3mV
Feedback chain tolerance = ±1% = ±10.5mV
Load regulation = ±0.25% = ±2.6mV
Please see Table 1 on this page for recommended
resistor values for some standard output voltages. All
resistors are 1%, 1/10W.
Set resistors per Table 1 should be 11.0kΩ (top) and
10.0kΩ (bottom).
The maximum output voltage that can be obtained from
each output is determined by the input supply voltage
and the R DS(ON) and gate threshold voltage of the
external MOSFET. Assuming that the MOSFET gate
threshold voltage is sufficiently low for the output
voltage chosen and the worst-case drive voltage, VOUT(MAX)
is given by:
Total DC error = ±3.75% = 39.4mV
This leaves ±1.25% = 13.1mV for the load transient ESR
spike, therefore:
13.1mV
= 5.2mΩ
2 .5 A
Bulk capacitance required is given by:
RESR(MAX ) =
VOUT (MAX ) = VDRAIN(MIN ) − IOUT (MAX ) • RDS( ON)(MAX )
dI • t
µF
dV
Where dI is the maximum load current step, t is the
maximum regulator response time and dV is the
CBULK (MIN ) =
 2004 Semtech Corp.
8
www.semtech.com
SC338(A)
POWER MANAGEMENT
Applications Infomation (Cont.)
allowable voltage droop. Therefore with dI = 2.5A,
t = 1µs, and dV = 13.1mV:
Solution 2: using passive droop.
2.5 • 1 • 10 −6
= 191µF
13.1 • 10 −3
So if we use 1% VOUT set resistors we would select 2 x
>100µF, 12mΩ POSCAPs for output capacitance (which
assumes that local ceramic bypass capacitors will
absorb the balance of the (6 - 5.3)mΩ ESR
requirement - otherwise 10mΩ capacitors should be
used).
CBULK (MIN) =
1.2V +/-5% IN
C1
0.1uF
8
1.075V
1.05V @ 2.5A
C3
4
R2
4
10.0k
5
U1
DRV1
ADJ1
EN1
PGD1
GND
SC338(A)
10
IN
9
DRV2
8
ADJ2
7
EN2
6
PGD2
Passive droop allows us to use almost the full output
tolerance window for transients, hence making the
output capacitor selection simpler and (hopefully)
cheaper. The trade-offs are the cost of the droop
resistor versus the reduction in output capacitor cost,
and the reduction in headroom which impacts MOSFET
selection. The top of the feedback chain connects to the
“input” side of RDROOP, and the output is set for 1.075V.
Thus at no load, VOUT will be 1.075V (or 1.05V + 2.4%)
and at IOUT = 2.5A, VOUT will be 1.025V (or 1.05V - 2.4%).
Obviously this is a very severe example, since the output
voltage is so low and therefore the allowable window is
very small. See solution 2 below for an alternate
solution. For higher output voltages the components
required will be less stringent.
If 1% set resistors are used, the total DC error will be
±3.75% = 39mV. Thus at no load, the minimum output
voltage will be given by:
The input capacitance needs to be large enough to stop
the input supply from collapsing below -5% (i.e. the
design minimum) during output load steps. If the input to
the pass MOSFET is not local to the supply bulk
capacitance then additional bulk capacitance may be
required.
VOUT (MIN _ NO _ LOAD ) = 1.075 − 0.039 = 1.036 V
This leaves 38.5mV for transient response, giving:
RESR(MAX ) =
MOSFET selection: since the input voltage to the
SC338(A) is 5V±5%, the minimum available gate drive
is:
38.5mV
= 15.4mΩ and
2.5 A
2.5 • 1 • 10 −6
= 65µF
38.5 • 10 −3
Instead of 2 x 100µF, 12mΩ capacitors, we can use 1 x
100µF, 15mΩ capacitor.
CBULK (MIN) =
VGS = ( 4.4 − 1.1025 ) = 3.3 V
So a MOSFET rated for VGS = 2.7V will be required, with
an RDS(ON)(MAX) (over temp.) given by:
Layout Guidelines
(1.14 − 1.05 )
= 36m Ω
2. 5
The advantages of using the SC338(A) to drive external
MOSFETs are a) that the bandgap reference and control
circuitry are in a die that does not contain high power
dissipating devices and b) that the device itself does not
Obviously, if a 12V rail is available to power the SC338(A),
the number of FET options increases dramatically.
 2004 Semtech Corp.
1
2
2.5 • 1 • 10 −6
= 111µF
22.6 • 10 −3
So for 0.1% resistors we could use 2 x 100µF, 18mΩ
POSCAPs for output capacitance, or 1 x >100µF, 10mΩ
POSCAP.
IOUT (MAX )
11.0k
3
CBULK (MIN) =
=
3
2
22.6mV
= 9.0mΩ and
2 .5 A
RDS( ON)MAX ) =
5
1
R1
If we use 0.1% set resistors, then the total DC error
becomes ±2.85% = ±29.9mV, leaving ±2.15% = 22.6mV
for the ESR spike. In this case:
( VIN(MIN ) − VOUT )
6
Q1
IRF7311
or similar
20mOhm
100uF, 25mOhm POSCAP
RESR(MAX ) =
7
RDROOP
9
www.semtech.com
SC338(A)
POWER MANAGEMENT
Applications Infomation (Cont.)
PRELIMINARY
need to be located right next to the power devices. Thus
very accurate output voltages can be obtained since
changes due to heating effects will be minimal.
The 0.1µF bypass capacitor should be located close to
the supply (IN) and GND pins, and connected directly to
the ground plane.
The feedback resistors should be located at the device,
with the sense line from the output routed from the load
(or top end of the droop resistor if passive droop is being
used) directly to the feedback chain. If passive droop is
being used, the droop resistor should be located right at
the load to avoid adding additional unplanned droop.
Sense and drive lines should be routed away from noisy
traces or components.
For very low input to output voltage differentials, the
input to output / load path should be as wide and short
as possible. Where greater headroom is available, wide
traces may suffice.
Power dissipation within the device is practically
negligible, thus requiring no special consideration during
layout. The MOSFET pass devices should be laid out
according to the manufacturer’s guidelines for the power
being dissipated within them.
 2004 Semtech Corp.
10
www.semtech.com
SC338(A)
POWER MANAGEMENT
Typical Characteristics
Quiescent Current vs. Junction Temperature
Standby Current vs. Junction Temperature
vs. Input Voltage
vs. Input Voltage
900
100
Both VEN = 5V
Both VADJ < VBG
800
VIN = 12V
700
10
IQ(OFF) (µA)
VIN = 12V
600
IQ (µA)
Both VEN = 0V
500
400
VIN = 5V
1
300
0.1
200
VIN = 5V
100
0
0.01
-50
-25
0
25
50
75
100
125
-50
-25
0
25
TJ (°C)
Enable Input Threshold Voltage
Junction Temperature
vs. Junction Temperature
1.8
4.5
100
125
100
125
VIN = 5V
1.6
VIN rising
4.0
1.4
3.5
VIH
3.0
VIN falling
2.5
VIH/L (V)
VUVLO (V)
75
Start Threshold vs.
5.0
2.0
1.5
1.2
1.0
VIL
0.8
1.0
0.6
0.5
0.4
0.0
-50
-25
0
25
50
75
100
-50
125
-25
0
25
0.510
0.508
50
75
TJ (°C)
TJ (°C)
Reference Voltage vs.
Drive Pin Output Current (Sourcing) at Startup
Junction Temperature
vs. Junction Temperature vs. Input Voltage
20
VIN = VEN = 5V
18
0.506
16
0.504
14
0.502
12
IDRV (µA)
VADJ (mV)
50
TJ (°C)
0.500
0.498
VIN = 12V
10
8
0.496
6
0.494
4
0.492
2
0.490
VEN = 5V
VADJ < VTH(PGD)
VIN = 5V
0
-50
-25
0
25
50
75
100
125
-50
 2004 Semtech Corp.
-25
0
25
50
75
100
125
TJ (°C)
TJ (°C)
11
www.semtech.com
SC338(A)
POWER MANAGEMENT
Typical Characteristics (Cont.)
PRELIMINARY
Drive Pin Output Current (Sourcing) vs.
Drive Pin Output Current (Sinking) vs.
Junction Temperature vs. Input Voltage
Junction Temperature vs. Input Voltage
1200
5.0
4.5
VEN = 5V
VADJ < VBG
VIN = 12V
4.0
1000
800
3.0
IDRV (µA)
IDRV (mA)
3.5
VIN = 12V
VEN = 5V
VADJ > VBG
2.5
2.0
VIN = 5V
600
400
1.5
VIN = 5V
1.0
200
0.5
0.0
0
-50
-25
0
25
50
75
100
-50
125
-25
0
25
Under Voltage Trip Threshold
Junction Temperature vs. Input Voltage
vs. Junction Temperature
-44
VIN = 5V
-46
VTH(UV) (%VADJ)
VIN = 12V
5
VDRV (V)
125
100
125
VIN = VEN = 5V
-42
6
4
3
-48
-50
-52
-54
VEN = 5V
IDRV = 0mA
VADJ < VBG
-56
-58
0
-60
-50
-25
0
25
50
75
100
-50
125
-25
0
25
50
75
TJ (°C)
TJ (°C)
Power Good Threshold vs.
Power Good Logic Low Output Voltage
Junction Temperature
vs. Junction Temperature
0.0
200
VIN = VEN = 5V
175
-2.5
150
-5.0
-7.5
VPGD (mV)
VTH(PGD) (%VADJ)
100
-40
7
1
75
Drive Pin Output Voltage (Full On) vs.
8
2
50
TJ (°C)
TJ (°C)
Startup only
-10.0
VIN = VEN = 5V
VADJ = 0.4V
IPGD = -1mA
125
100
75
50
-12.5
Normal operation
25
-15.0
0
-50
-25
0
25
50
75
100
125
-50
TJ (°C)
 2004 Semtech Corp.
-25
0
25
50
75
100
125
TJ (°C)
12
www.semtech.com
SC338(A)
POWER MANAGEMENT
Typical Characteristics (Cont.)
Output Rise Time At Startup vs. Soft Start
Capacitance vs. Input Voltage
100
VEN = 5V
TJ = 25°C
VOUT = 1.05V
COUT = 100µF, 25mΩ
IOUT = 0A
MOSFET = IRF7311
tr(OUT) (ms)
10
VIN = 5V
1
VIN = 12V
0.1
0.1
1
10
100
CDRV (nF)
Load Transient Response, No Passive Droop
Load Transient Response, With Passive Droop
VIN = 5V, 1.2V in to 1.05V out
IOUT = 0.01A to 2.51A to 0.01A
COUT = 1 x 100µF, 25mΩ
RDROOP = 20mΩ
Trace 1: VOUT, 20mV/div., offset 1V
Trace 2: not connected
Trace 3: 1.2V in, 50mV/div., offset 1V
Trace 4: load FET drain
Timebase: 20µs/div.
Load rise/fall times ≥ 35A/µs
VIN = 5V, 1.2V in to 1.05V out
IOUT = 0.01A to 2.51A to 0.01A
COUT = 2 x 100µF, 25mΩ
Trace 1: VOUT, 20mV/div., offset 1V
Trace 2: VDRV, 2V/div.
Trace 3: 1.2V in, 50mV/div., offset 1V
Trace 4: load FET drain
Timebase: 20µs/div.
Load rise/fall times ≥ 35A/µs
 2004 Semtech Corp.
13
www.semtech.com
SC338(A)
POWER MANAGEMENT
Outline Drawing - MSOP-10
PRELIMINARY
e
A
DIM
D
2X E/2
ccc C
2X N/2 TIPS
E
E1
PIN 1
INDICATOR
.043
.000
.006
.030
.037
.007
.011
.003
.009
.114 .118 .122
.114 .118 .122
.193 BSC
.020 BSC
.016 .024 .032
(.037)
10
8°
0°
.004
.003
.010
A
A1
A2
b
c
D
E1
E
e
L
L1
N
01
aaa
bbb
ccc
N
12
B
DIMENSIONS
INCHES
MILLIMETERS
MIN NOM MAX MIN NOM MAX
1.10
0.00
0.15
0.75
0.95
0.17
0.27
0.08
0.23
2.90 3.00 3.10
2.90 3.00 3.10
4.90 BSC
0.50 BSC
0.40 0.60 0.80
(.95)
10
0°
8°
0.10
0.08
0.25
D
aaa C
SEATING
PLANE
A2
H
A
bxN
bbb
c
GAGE
PLANE
A1
C
C A-B D
0.25
L
(L1)
DETAIL
SEE DETAIL
SIDE VIEW
01
A
A
NOTES:
1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES).
2. DATUMS -A- AND -B- TO BE DETERMINED AT DATUM PLANE -H3. DIMENSIONS "E1" AND "D" DO NOT INCLUDE MOLD FLASH, PROTRUSIONS
OR GATE BURRS.
4. REFERENCE JEDEC STD MO-187, VARIATION BA.
Land Pattern - MSOP-10
X
DIM
(C)
G
Y
Z
C
G
P
X
Y
Z
DIMENSIONS
INCHES
MILLIMETERS
(.161)
.098
.020
.011
.063
.224
(4.10)
2.50
0.50
0.30
1.60
5.70
P
NOTES:
1.
THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY.
CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR
COMPANY'S MANUFACTURING GUIDELINES ARE MET.
Contact Information
Semtech Corporation
Power Management Products Division
200 Flynn Road, Camarillo, CA 93012
Phone: (805)498-2111 FAX (805)498-3804
 2004 Semtech Corp.
14
www.semtech.com