SPECIFICATION FOR APPROVAL REF : PAGE: 1 PROD. ABC'S DWG NO. SMD LINE FILTER NAME SF6018□□□□L□-□□□ ABC'S ITEM NO. Ⅰ﹒CONFIGURATION & DIMENSIONS： 4 1 3 3 1 A B A : B : C : E : F : G : Wψ : m/m m/m m/m m/m m/m m/m m/m G C 3 2 6.50 max. 3.60±0.15 1.65±0.15 2.50±0.10 4.80±0.20 0.20 min. 1.00±0.2 F 4.80 Ⅱ﹒SCHEMATIC DIAGRAM： 1.80 2.50 E Wψ (PCB Pattern Suggestion) N1 1 4 2 3 N2 " " ：Polarity Ⅲ﹒MATERIALS： c a﹒Core：Ferrite core b﹒Wire：Enamelled copper wire c﹒Base： DAP 9100F base d﹒Terminal： Cu / Ni /Sn Ni plating 1.5 um min. Sn plating 7 um min. after soldering a b d Peak Temp ：260 ℃ max. Max time above 230℃ ：50sec max. Max time above 200℃ ：70sec max. e﹒Remark：Products comply with RoHS' requirements Temperature Rising Area Preheat Area +4.0℃ / sec max. 150 ~ 200℃ / 60 ~ 120sec Reflow Area +2.0 ~ 4.0℃ Forced Cooling Area -(1.0 ~ 5.0)℃ / sec max. Peak Temperature: 260℃ 250 Ⅳ﹒GENERAL SPECIFICATION： a﹒ Temp. rise ：40℃ max. at rated current b﹒Storage temp.：-40℃ ----+120℃ c﹒Operating temp.：-40℃----+125℃ (included Temp. rise) d﹒ Resistance to solder heat：260℃.10 secs. AE-001A Temperature ( ℃ ) 50sec max. 230℃ 200 150 70sec max. 100 50 0 50 100 150 Time ( seconds ) 200 250 SPECIFICATION FOR APPROVAL REF : PAGE: 2 PROD. ABC'S DWG NO. SMD LINE FILTER NAME SF6018□□□□L□-□□□ ABC'S ITEM NO. Ⅴ﹒ELECTRICAL CHARACTERISTICS ： DWG No. L(µH) 20mV/10kHz ｜L-L｜ (µH max.) RDC(N1=N2) ( Ω max. ) Impedance HI-POT Test Freq. range MHz min(Ω) SF6018100YL□ -□□□ 10±50% 1.0 0.24 350~570 600 SF6018470YL□ -□□□ 47±50% 4.0 0.16 4~1600 140 SF6018820YL□ -□□□ 82±50% 4.0 0.20 3~850 220 SF6018101YL□ -□□□ 100±50% 8.0 0.22 3~660 260 SF6018181YL□ -□□□ 180±50% 8.0 0.25 3~250 500 SF6018221YL□ -□□□ 220±50% 10 0.28 3~210 600 SF6018331YL□ -□□□ 330±50% 10 0.30 3~120 900 250 Vac 60 Hz 3 mA 1 min. 1). □：Packaging information … A：Bulk B：Taping Reel 2)."":Reference code 3). Test equipment : Inductance ( HP4284A, 20mV/ 10kHz ) RDC ( CH-502AC ) Impedance ( E4991A ) 4). Nominal voltage : 60Vdc 5). Rated current : 300 mA ( Base on series both winding.) □□□ Impedance CURVE 10000 Measuring Circuit : 331 221 1000 100 181 Z (Ω)typ. 101 820 470 100 RF Impedance Analyzer 10 0.1 1 10 Frequency (MHz) AE-001A 100 1000 SPECIFICATION FOR APPROVAL PAGE: 3 REF : PROD. ABC'S DWG NO. SMD LINE FILTER NAME SF6018□□□□L□-□□□ ABC'S ITEM NO. Ⅵ﹒PACKAGING INFORMATION ( 1 ) Configuration T Cover Tape N A B 2.0±0.5 ∮C ∮C D G Embossed Carrier ※ Carrier tape width : D P:8m/m 4m/m End Start 0 0 1 0 0 1 0 0 1 0 0 1 0 0 1 Leader no component 200 m/m min. Trailer no component 400 m/m min. Components User direction of feed ( 2 ) Dimensions Unit:m/m Style A 07 - 12 178 B 21±0.8 C D 13 12 N G 14 +0 50 T -0 18.4 ( 3 ) Q'TY & G.W. Per package Inner : Reel Series SF6018 AE-001A Q'TY (pcs) G.W. (gw) 1000 300 Outer : Carton Style 07 - 12 Q'TY (pcs) 40,000 G.W. (Kg) 12.0 Size (cm) 42 x 41 x 24 SPECIFICATION FOR APPROVAL REF : PAGE: 4 PROD. ABC'S DWG NO. SMD LINE FILTER NAME SF6018□□□□L□-□□□ ABC'S ITEM NO. Ⅷ﹒DWGING NUMBER EXPRESSION： S F 6 0 1 8 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code Appendix code 1： Product Classification L：Lead Free Standard products comply with RoHS' requirements 1 ~ 9 ：Lead Free Special products comply with RoHS' requirements Appendix code 2：Package Information Code AE-001A Inner package A T.B.D. B T / R ( Reel package ) Inner package Q'TY T.B.D. 1000 pcs Remark SPECIFICATION FOR APPROVAL PAGE: 5 REF : PROD. SMD LINE FILTER NAME ABC'S DWG NO. SF6018□□□□L□-□□□ ABC'S ITEM NO. Ⅷ﹒ RELIABILITY TEST： Test item Solderability Thermal shock test ( Temp. cycle ) Specification Test condition More than 90% of the terminal electrode Shall be covered With fresh solder. Preheat : 150±25℃ for 60 seconds Solder : Sn96.5 / Ag3 / Cu0.5 or equivalent Solder temp. : 260±5℃ Flux : Rosin Dip time : 4±1 seconds Inductance shall not change more than ±20% Room temp. 15 minutes -25±2 ℃ 30 minutes Room temp. 15 minutes 85±2 ℃ Total : 50 cycles Humidity Resistance test High temp. Resistance test AE-001A Temperature : 40±2℃ Humidity : 90 ~ 95% Applied current : Per spec. Time : 500 hours Temperature : 80±2℃ Applied current : Per spec. Time : 500 hours 30 minutes SPECIFICATION FOR APPROVAL PAGE: 6 REF : PROD. ABC'S DWG NO. SMD LINE FILTER NAME SF6018□□□□L□-□□□ ABC'S ITEM NO. Ⅸ﹒ DWG EXPRESSION： OBMW2 Magnet Wire-Component September 8, 2000 JUNG SHING WIRE CO LTD 231 CHUNG CHENG RD, SEC 3 JEN-TEH HSIANG, TAINAN HSIEN TAIWAN Mtl Dsg AIW CFUEWB EIAIW EILOCKY EILOCKW EIW EIW-2 FL.EILOCKY LSFFW LSUEW PEW PEY SF.FLW SF.EIW SF.BY@ SF.FLY@ SF.BLOCKBS SF.EILOCKY# SF.EILOCKBS SF.BW@ SFFW Mark Dsg ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ BC Polyamideimide Polyurethane Polyesterimide Polyesterimide Polyesterimide Polyesterimide Polyesterimide Modified Polyester Polyurethane Polyurethane Polyester Polyester Modified Polyester Polyesterimide Modified Polyester Modified Polyester Modified Polyester Polyesterimide Polyesterimide SFFY UEW-1 UEW-2 UEW-4 UEY UEY-2 OC ____ ____ Polyamideimide Polyamide Modified Epoxy ____ ____ Polyamide ____ ____ ____ ____Nylon ____ Nylon Nylon Modified Polyamide Polyamide Modified Polyamide ____ Modified Polyester Polyurethane ANSI Type Temp Class MW81-C MW75C MW35C ___ ___ 220 130 200 180 200 ___ MW74-C ___ MW79-C ___ ___ MW24-C MW26C MW77C MW27-C MW27-C ___ ___ ___ Mark Dsg ____ ____ ____ ____ ____ ____ BC Coat Typ Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane 220 200 155 155 130 155 155 155 180 155 155 155 180 180 MW26C MW79 155 155 A not-for-profit organization dedicated to public safety and committed to quality service Page 1 of 2 287806002 Mtl Dsg Coat Typ E174837 OC Polyamide ____ ____ ____ Nylon Polyamide ANSI Type Temp Class MW80C MW2-C ___ 155 105 130 130 130 130 MW75C MW28-C MW28-C @-May be suffixed by LZ; # - May be suffixed by LZ, EL or LZI. LZ - Signifies magned wires twisted together; EL - signifies base coated magnet wire laid parallel with top coat applied overall; LZL - signifies base coated magnet wire twisted together and covered with top coat overall. Marking: Company name or trademarks or 榮星電線 , material designation or marked designation on packaed or reel, and Recognized Component Mark. See General Information Preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. 287806002 AE-001A Page 2 of 2 OBMW2⁄E174837 September 8 , 2000 SPECIFICATION FOR APPROVAL REF : PAGE: 7 PROD. NAME ABC'S DWG NO. SMD LINE FILTER SF6018□□□□L□-□□□ ABC'S ITEM NO. Friday , October 24, 2003 QMFZ2 Component - Plastics E150608 WAH HONG INDUSTRIAL CORP 10TH FL 235 CHUNG CHENG 4TH RD KAOHSIUNG TAIWAN Material Designation: Product Description: Diallyl Phthalate ( DAP ), molding compound, furnished as pellets. Color Min. Thick. (m/m) HWI HAI Flame Class RTI RTI RTI Elec Imp Str BK 0.37 V-0 0 3 130 130 130 BK 0.82 V-0 2 0 130 130 130 CTI: 0 HVTR: 0 D495: 4 IEC GWIT IEC GWFI IEC Ball Pressure (℃): - Dielectric Strength (kV/m/m): - Volume Resistivity (10 xohm-cm): - Dimensional Stability (%): - ISO Tensile Strength (MPa): - ISO Flexural Strength (MPa): - ISO Tensile Impact (kJ/m 2 ): - ISO Heat Deflection (℃): - ISO Izod Impact (kJ/m2 ): - ISO Charpy Impact (kJ/m2 ): - Report Date: 8/18/1998 Underwriters Laboratories Inc R UL94 small-scale test data does not pertain to building materials, furnishings and related contents. UL 94 small-scale test data is intended solely for determining the flammability of plastic materials used in components and parts of end-product devices and appliances, where the acceptability of the combination is determined by ULI. AE-001A