TI SN65LVDS122D

SN65LVDS122
SN65LVDT122
www.ti.com
SLLS525B – MAY 2002 – REVISED JUNE 2004
1.5-Gbps 2 × 2 LVDS CROSSPOINT SWITCH
FEATURES
•
DESCRIPTION
Designed for Signaling Rates Up To
1.5 Gbps
Total Jitter < 65 ps
Pin-Compatible With SN65LVDS22 and
SN65LVDM22
25 mV of Receiver Input Threshold Hysteresis
Over 0-V to 4-V Common-Mode Range
Inputs Electrically Compatible With CML,
LVPECL and LVDS Signal Levels
Propagation Delay Times, 900 ps Maximum
LVDT Integrates 110-Ω Terminating Resistor
Offered in SOIC and TSSOP
(1)
•
•
•
•
•
•
•
APPLICATIONS
•
•
•
•
•
10-G (OC-192) Optical Modules
622-MHz Central Office Clock Distribution
Wireless Basestations
Low Jitter Clock Repeater/Multiplexer
Protection Switching for Serial Backplanes
(1)
The signlaing rate of a line is the number of voltage
transitions that are made per second expressed in the units
bps (bits per second).
The SN65LVDS122 and SN65LVDT122 are
crosspoint switches that use low voltage differential
signaling (LVDS) to achieve signaling rates as high
as 1.5 Gbps. They are pin-compatible speed upgrades to the SN65LVDS22 and SN65LVDM22. The
internal signal paths maintain differential signaling for
high speeds and low signal skews. These devices
have a 0-V to 4-V common-mode input range that
accepts LVDS, LVPECL, or CML inputs. Two logic
pins (S0 and S1) set the internal configuration between the differential inputs and outputs. This allows
the flexibility to perform the following configurations:
2 x 2 crosspoint switch, 2:1 input multiplexer, 1:2
splitter or dual repeater/translator within a single
device. Additionally, SN65LVDT122 incorporates a
110-Ω termination resistor for those applications
where board space is a premium. Although these
devices are designed for 1.5 Gbps, some applications
at a 2-Gbps data rate can be supported depending on
loading and signal quality.
The intended application of this device is ideal for
loopback switching for diagnostic routines, fanout
buffering of clock/data distribution provide protection
in fault-tolerant systems, clock multiplexing in optical
modules, and for overall signal boosting over
extended distances.
The SN65LVDS122 and SN65LVDT122
characterized for operation from –40°C to 85°C.
EYE PATTERNS OF OUTPUTS
OPERATING SIMULTANEOUSLY
FUNCTIONAL DIAGRAM
1DE
1A
1Y
1Z
110 Ω
are
1.5 Gbps
223 − 1 PRBS
OUTPUT 1
1B
VCC = 3.3 V
S0
MUX
S1
2A
110 Ω
2B
VID = 200 mV, VIC = 1.2 V
Vertical Scale=200 mV/div
2Y
2Z
OUTPUT 2
2DE
Integrated Termination on SN65LVDT122 Only
Horizontal Scale= 200 ps/div
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2002–2004, Texas Instruments Incorporated
SN65LVDS122
SN65LVDT122
www.ti.com
SLLS525B – MAY 2002 – REVISED JUNE 2004
These devices have limited built-in ESD protection. The leads should be shorted together or the device
placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION
TERMINATION RESISTOR
PART NUMBER (1)
SYMBOLIZATION
SOIC
No
SN65LVDS122D
LVDS122
SOIC
Yes
SN65LVDT122D
LVDT122
TSSOP
No
SN65LVDS122PW
LVDS122
TSSOP
Yes
SN65LVDT122PW
LVDT122
PACKAGE
(1)
Add the suffix R for taped and reeled carrier
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range unless otherwise noted (1)
SN65LVDS122, SN65LVDT122
VCC
Supply voltage
range (2)
–0.5 V to 4 V
(A, B)
Voltage range
–0.7 V to 4.3 V
|VA-VB| (LVDT only)
1V
(DE, S0, S1)
–0.5 V to 4 V
(Y, Z)
–0.5 V to 4 V
Human Body Model (3)
ESD
Charged-Device
Model (4)
A, B, Y, Z, and GND
±4 kV
All pins
±2 kV
±1500 V
All pins
Continuous power dissipation
Tstg
See Dissipation Rating Table
Storage temperature range
–65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds
(1)
(2)
(3)
(4)
260°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values, except differential I/O bus voltages, are with respect to network ground terminal.
Tested in accordance with JEDEC Standard 22, Test Method A114-A.7.
Tested in accordance with JEDEC Standard 22, Test Method C101.
RECOMMENDED OPERATING CONDITIONS
MIN
NOM
MAX
3
3.3
UNIT
VCC
Supply voltage
3.6
V
VIH
High-level input voltage
S0, S1, 1DE, 2DE
2
4
V
VIL
Low-level input voltage
S0, S1, 1DE, 2DE
0
0.8
V
LVDS
0.1
1
LVDT
0.1
0.8
|VID|
Magnitude of differential input voltage
Input voltage (any combination of common-mode or input signals)
TA
Operating free-air temperature
0
4
V
–40
85
°C
PACKAGE DISSIPATION RATINGS
TA ≤ 25°C
POWER RATING
DERATING FACTOR (1)
ABOVE TA = 25°C
TA = 85°C
POWER RATING
PW
712 mW
6.2 mW/°C
340 mW
D
1002 mW
8.7 mW/°C
480 mW
PACKAGE
(1)
2
V
This is the inverse of the junction-to-ambient thermal resistance when board-mounted and with no air flow.
SN65LVDS122
SN65LVDT122
www.ti.com
SLLS525B – MAY 2002 – REVISED JUNE 2004
INPUT ELECTRICAL CHARACTERISTICS
over recommended operating conditions (unless otherwise noted)
PARAMETER
VIT+
Positive-going differential input voltage threshold
VIT-
Negative-going differential input voltage threshold
TEST CONDITIONS
MIN TYP (1) MAX
See Figure 1 and Table 1
See Figure 1 and Table 1
100
–100 (2)
VID(HYS) Differential input voltage hysteresis (VIT+– VIT-)
IIH
High-level input current
IIL
Low-level input current
ICC
Supply current
DE
S0, S1
DE
S0, S1
Input current (A or B inputs 'LVDS)
II
Input current (A or B inputs 'LVDT)
Input current (A or B inputs 'LVDS)
II(OFF)
Input current (A or B inputs 'LVDT)
IIO
(1)
(2)
0
0
20
0
20
RL = 100 Ω
80
100
Disabled
35
45
VI = 0 V or 2.4 V, Other input at 1.2 V
–20
20
0
33
–40
40
0
66
VCC = 1.5 V, VI = 0 V or 2.4 V,
Other input at 1.2 V
–20
20
VCC = 1.5 V, VI = 2.4 V or 4 V,
Other input at 1.2 V
0
33
VCC = 1.5 V, VI = 0 V or 2.4 V,
Other input open
–40
40
VCC = 1.5 V, VI = 2.4 V or 4 V,
Other input open
0
66
6
VI = 4 V, Other input at 1.2 V
VI = 0 V or 2.4 V, Other input open
VI = 4 V, Other input open
µA
mA
µA
µA
µA
VIA = VIB, 0 ≤ VIA ≤ 4 V
–6
Termination resistance ('LVDT)
VID = 300 mV and 500 mV,
VIC = 0 V to 2.4 V
90
110
132
Termination resistance ('LVDT with power-off)
VID = 300 mV and 500 mV,
VCC = 1.5 V, VIC = 0 V to 2.4 V
90
110
132
Differential input capacitance ('LVDT with
power-off)
µA
µA
Input offset current (| IIA– IIB |) 'LVDS
RT
CI
mV
–10
–10
VIL = 0.8 V
mV
mV
25
VIH = 2
UNIT
µA
Ω
VI = 0.4 sin (4E6πt) + 0.5 V
3
Powered down (VCC = 1.5 V)
3
pF
All typical values are at 25°C and with a 3.3-V supply.
The algebraic convention in which the least positive (most negative) limit is designated as minimum is used in this data sheet.
OUTPUT ELECTRICAL CHARACTERISTICS
over recommended operating conditions (unless otherwise noted)
PARAMETER
|VOD|
Differential output voltage magnitude
∆|VOD|
Change in differential output voltage magnitude between logic
states
VOC(SS)
Steady-state common-mode output voltage
∆VOC(SS)
Change in steady-state common-mode output voltage between
logic states
VOC(PP)
Peak-to-peak common-mode output voltage
IOS
TEST CONDITIONS
MIN TYP (1)
247
See Figure 2
310
MAX
UNIT
454
mV
–50
50
1.125
1.375
See Figure 3
–50
50
mV
150
mV
Short-circuit output current
VO(Y) or VO(Z) = 0 V
–24
24
mA
IOS(D)
Differential short-circuit output current
VOD = 0 V
–12
12
mA
IOZ
High-impedance output current
VOD = 600 mV
–1
1
VO = 0 V or VCC
–1
1
Co
Differential output capacitance
(1)
50
VI = 0.4 sin (4E6πt) + 0.5 V
3
V
µA
pF
All typical values are at 25°C and with a 3.3-V supply.
3
SN65LVDS122
SN65LVDT122
www.ti.com
SLLS525B – MAY 2002 – REVISED JUNE 2004
TIMING CHARACTERISTICS
PARAMETER
tSET
Input to select setup time
tHOLD
Input to select hold time
tSWITCH
Select to switch output
TEST CONDITIONS
MIN
NOM MAX
UNIT
0
ns
0.5
ns
1
2
2.6
ns
SWITCHING CHARACTERISTICS
over recommended operating conditions (unless otherwise noted)
PARAMETER
tPLH
Propagation delay time, low-to-high-level output
tPHL
Propagation delay time, high-to-low-level output
tr
Differential output signal rise time (20% - 80%)
tf
Differential output signal fall time (20% - 80%)
tsk(p)
Pulse skew (|tPHL - tPLH|) (2)
skew (3)
TEST CONDITIONS
See Figure 4
MIN
NOM (1) MAX
UNIT
400
650
900
ps
400
650
900
ps
280
ps
280
ps
50
ps
10
tsk(pp)
Part-to-part
100
ps
tjit(per)
Period jitter, rms (1 standard deviation) (4)
750 MHz clock input (5)
1
2.2
ps
tjit(cc)
Cycle-to-cycle jitter (peak) (4)
750 MHz clock input (6)
10
17
ps
33
65
ps
17
50
ps
jitter (4)
VID = 0.2 V
Peak-to-peak
tjit(det)
Deterministic jitter, peak-to-peak (4)
1.5 Gbps 27–1 PRBS input (8)
tPHZ
Propagation delay time, high-level-to-high-impedance output
See Figure 5
6
8
ns
tPLZ
Propagation delay time, low-level-to-high-impedance output
See Figure 5
6
8
ns
tPZH
Propagation delay time, high-impedance-to-high-level output
See Figure 5
4
6
ns
tPZL
Propagation delay time, high-impedance-to-low-level output
See Figure 5
4
6
ns
tsk(o)
Output skew (9)
15
40
ps
(4)
(5)
(6)
(7)
(8)
(9)
4
PRBS
input (7)
tjit(pp)
(1)
(2)
(3)
1.5 Gbps
223–1
All typical values are at 25°C and with a 3.3-V supply.
tsk(p) is the magnitude of the time difference between the tPLH and tPHL of any output of a single device.
tsk(pp) is the magnitude of the difference in propagation delay times between any specified terminals of two devices when both devices
operate with the same supply voltages, at the same temperature, and have identical packages and test circuits.
Jitter is specified by design and characterization. Stimulus jitter has been subtracted.
Input voltage = VID = 200 mV, 50% duty cycle at 750 MHz, tr = tf = 50 ps (20% to 80%), measured over 1000 samples.
Input voltage = VID = 200 mV, 50% duty cycle at 750 MHz, tr = tf = 50 ps (20% to 80%).
Input voltage = VID = 200 mV, 223–1 PRBS pattern at 1.5 Gbps, tr = tf = 50 ps (20% to 80%), measured over 200 k samples.
Input voltage = VID = 200 mV, 27–1 PRBS pattern at 1.5 Gbps, tr = tf = 50 ps (20% to 80%).
Output skew is the magnitude of the time delay difference between the outputs of a single device with all inputs tied together.
SN65LVDS122
SN65LVDT122
www.ti.com
SLLS525B – MAY 2002 – REVISED JUNE 2004
PIN ASSIGNMENT
D OR PW PACKAGE
(TOP VIEW)
1B
1A
S0
1DE
S1
2A
2B
GND
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
VCC
VCC
1Y
1Z
2DE
2Z
2Y
GND
Circuit Function Table
INPUTS (1)
OUTPUTS (1)
1VID
2VID
S1
S0
1DE
2DE
1VOD
2VOD
X
X
X
X
L
L
Z
Z
> 100 mV
X
L
L
H
L
H
Z
< -100 mV
X
L
L
H
L
L
Z
< -100 mV
X
L
L
H
H
L
L
> 100 mV
X
L
L
H
H
H
H
> 100 mV
X
L
L
L
H
Z
H
< -100 mV
X
L
L
L
H
Z
L
> 100 mV
X
H
L
H
L
H
Z
< -100 mV
X
H
L
H
L
L
Z
< -100 mV
< -100 mV
H
L
H
H
L
L
< -100 mV
> 100 mV
H
L
H
H
L
H
> 100 mV
< -100 mV
H
L
H
H
H
L
> 100 mV
> 100 mV
H
L
H
H
H
H
X
> 100 mV
H
L
L
H
Z
H
X
< -100 mV
H
L
L
H
Z
L
X
> 100 mV
L
H
H
L
H
Z
X
< -100 mV
L
H
H
L
L
Z
X
< -100 mV
L
H
H
H
L
L
X
> 100 mV
L
H
H
H
H
H
X
> 100 mV
L
H
L
H
Z
H
X
< -100 mV
L
H
L
H
Z
L
X
> 100 mV
H
H
H
L
H
Z
X
< -100 mV
H
H
H
L
L
Z
< -100 mV
< -100 mV
H
H
H
H
L
L
< -100 mV
> 100 mV
H
H
H
H
H
L
> 100 mV
< -100 mV
H
H
H
> 100 mV
> 100 mV
H
H
H
H
L
H
H
H
H
> 100 mV
X
H
H
L
H
Z
H
< -100 mV
X
H
H
L
H
Z
L
LOGIC DIAGRAM
1DE
1A / 1B
1Y / 1Z
2A / 2B
2Y / 2Z
2DE
1DE
1A / 1B
1Y / 1Z
2A / 2B
2Y / 2Z
2DE
1DE
1A / 1B
1Y / 1Z
2A / 2B
2Y / 2Z
2DE
1DE
1A / 1B
1Y / 1Z
2A / 2B
2Y / 2Z
2DE
(1)
H = high level, L = low level, Z = high impedance, X = don't care
5
SN65LVDS122
SN65LVDT122
www.ti.com
SLLS525B – MAY 2002 – REVISED JUNE 2004
PARAMETER MEASUREMENT INFORMATION
IIA
VID
VIA
(VIA+VIB)/2
A
Y
B
Z
VOD
VOY
VIC
VIB
IIB
(VOY+VOZ)/2
VOZ
Figure 1. Voltage and Current Definitions
3.74 kΩ
Y
VOD
100 Ω
Z
3.74 kΩ
+
_
0 V ≤ Vtest ≤ 2.4 V
Figure 2. Differential Output Voltage (VOD) Test Circuit
A
Y
B
Z
A
≈ 1.4 V
B
≈1V
49.9 Ω ±1%
VID
VOC(PP)
49.9 Ω ±1%
1 pF
VOC
VOC(SS)
VOC
NOTE: All input pulses are supplied by a generator having the following characteristics: tr or tf ≤ 0.25 ns, pulse repetition rate
(PRR) = 0.5 Mpps, pulse width = 500 ±10 ns; RL = 100 Ω; CL includes instrumentation and fixture capacitance within
0,06 mm of the D.U.T.; the measurement of VOC(PP) is made on test equipment with a –3-dB bandwidth of at least
300 MHz.
Figure 3. Test Circuit and Definitions for the Driver Common-Mode Output Voltage
A
VIA
VID
Y
1 pF
B
VOD
100 Ω
VIA
1.4 V
VIB
1V
VID
0.4 V
0V
-0.4 V
Z
VIB
tPHL
tPLH
80%
VOD
0V
20%
tf
tr
NOTE: All input pulses are supplied by a generator having the following characteristics: tr or tf ≤ 0.25 ns, pulse repetition rate
(PRR) = 0.5 Mpps, pulse width = 500 ±10 ns. CL includes instrumentation and fixture capacitance within 0,06 mm of
the D.U.T.
Figure 4. Timing Test Circuit and Waveforms
6
SN65LVDS122
SN65LVDT122
www.ti.com
SLLS525B – MAY 2002 – REVISED JUNE 2004
PARAMETER MEASUREMENT INFORMATION (continued)
49.9 Ω ±1%
Y
1 V or 1.4 V
1.2 V
DE
A
1 pF
B
49.9 Ω ±1%
Z
3V
1.5 V
0V
DE
≅ 1.4 V
1.25 V
1.2 V
VOY or VOZ
1.2 V
tPZH
tPHZ
1.2 V
1.15 V
≅1V
VOZ or VOY
tPZL
tPLZ
NOTE: All input pulses are supplied by a generator having the following characteristics: tr or tf≤ 1 ns, pulse repetition rate
(PRR) = 0.5 Mpps, pulse width = 500 ±10 ns. CL includes instrumentation and fixture capacitance within 0,06 mm of
the D.U.T.
Figure 5. Enable and Disable Time Circuit and Definitions
INPUT 1
A
B
INPUT 2
C
D
SEL 0/1
t(SET)
OUTPUT1
A
t(HOLD)
B
C
D
t(SWITCH)
Figure 6. Example Switch, Setup, and Hold Times
7
SN65LVDS122
SN65LVDT122
www.ti.com
SLLS525B – MAY 2002 – REVISED JUNE 2004
PARAMETER MEASUREMENT INFORMATION (continued)
t(SET) and t(HOLD) times specify that data must be in a stable state before and after multiplex control switches.
Table 1. Receiver Input Voltage Threshold Test
APPLIED
VOLTAGES
(1)
8
RESULTING DIFFERENTIAL
INPUT VOLTAGE
RESULTING COMMONMODE INPUT VOLTAGE
OUTPUT (1)
VIA
VIB
VID
VIC
1.25 V
1.15 V
100 mV
1.2 V
1.15 V
1.25 V
–100 mV
1.2 V
L
4.0 V
3.9 V
100 mV
3.95 V
H
3.9 V
4. 0 V
–100 mV
3.95 V
L
0.1 V
0.0 V
100 mV
0.05 V
H
0.0 V
0.1 V
–100 mV
0.05 V
L
1.7 V
0.7 V
1000 mV
1.2 V
H
0.7 V
1.7 V
–1000 mV
1.2 V
L
4.0 V
3.0 V
1000 mV
3.5 V
H
3.0 V
4.0 V
–1000 mV
3.5 V
L
1.0 V
0.0 V
1000 mV
0.5 V
H
0.0 V
1.0 V
–1000 mV
0.5 V
L
H = high level, L = low level
H
SN65LVDS122
SN65LVDT122
www.ti.com
SLLS525B – MAY 2002 – REVISED JUNE 2004
EQUIVALENT INPUT AND OUTPUT SCHEMATIC DIAGRAMS
INPUT LVDS122
VCC
A
VCC
B
7V
7V
VCC
VCC
300 kΩ
400 Ω
S0, S1
DE1, DE2
400 Ω
300 kΩ
7V
7V
OUTPUT LVDS122
VCC
VCC
VCC
Y
7V
Z
7V
9
SN65LVDS122
SN65LVDT122
www.ti.com
SLLS525B – MAY 2002 – REVISED JUNE 2004
TYPICAL CHARACTERISTICS
DIFFERENTIAL OUTPUT
VOLTAGE
vs
FREQUENCY
DIFFERENTIAL PROPAGATION
DELAY
vs
COMMON-MODE INPUT VOLTAGE
1000
300
250
200
150
VCC = 3.3 V
TA = 25°C
VIC = 1.2 V
VID = 200 mV
Input = Clock
100
50
800
VCC = 3.3 V
TA = 25°C
VID = 200 mV
f = 150 MHz
900
800
tPHL
700
tPLH
600
700
tPHL
600
0
500
1000
1500
0
2000
f − Frequency − MHz
400
300
200
100
0
1
2
3
4
5
VIC − Common-Mode Input Voltage − V
−40 −20
0
20
40
60
80
Figure 9.
PEAK-TO-PEAK JITTER
vs
FREQUENCY
PEAK-TO-PEAK JITTER
vs
DATA RATE
PEAK-TO-PEAK JITTER
vs
FREQUENCY
60
30
VCC = 3.3 V
TA = 25°C
VIC = 400 mV
Input = PRBS 223 −1
VID = 0.5 V
VID = 0.8 V
10
5
40
VID = 0.8 V
VID = 0.5 V
30
20
VID = 0.3 V
10
VCC = 3.3 V
TA = 25°C
VIC = 1.2 V
Input = Clock
25
Peak-To-Peak Jitter − ps
Peak-To-Peak Jitter − ps
50
20
100
TA − Free Air Temperature − °C
Figure 8.
VCC = 3.3 V
TA = 25°C
VIC = 400 mV
Input = Clock
15
VCC = 3.3 V
VID = 200 mV
f = 150 MHz
Figure 7.
30
25
tPLH
500
500
0
Peak-To-Peak Jitter − ps
Differential Propagation Delay − ps
Differential Propagation Delay − ps
V O− Differential Output Voltage − mV
350
DIFFERENTIAL PROPAGATION
DELAY
vs
TEMPERATURE
20
15
VID = 0.3 V
VID = 0.5 V
10
VID = 0.8 V
5
VID = 0.3 V
0
0
0
200
400
600
800
0
0
f − Frequency − MHz
1200
1600
0
Figure 12.
PEAK-TO-PEAK JITTER
vs
DATA RATE
PEAK-TO-PEAK JITTER
vs
FREQUENCY
PEAK-TO-PEAK JITTER
vs
DATA RATE
20
VID = 0.3 V
50
20
Peak-To-Peak Jitter − ps
Peak-To-Peak Jitter − ps
VID = 0.5 V
VID = 0.3 V
VID = 0.8 V
15
10
5
VID = 0.3 V
800
30
VID = 0.5 V
20
VCC = 3.3 V
TA = 25°C
VIC = 2.8 V
Input = PRBS 223 −1
10
0
400
VID = 0.8 V
40
VID = 0.5 V
0
1200
Data Rate − Mbps
Figure 13.
1600
800
60
VCC = 3.3 V
TA = 25°C
VIC = 2.8 V
Input = Clock
25
VID = 0.8 V
0
600
Figure 11.
40
10
400
f − Frequency − MHz
30
30
200
Figure 10.
VCC = 3.3 V
TA = 25°C
VIC = 1.2 V
Input = PRBS 223 −1
50
Peak-To-Peak Jitter − ps
800
Data Rate − Mbps
60
10
400
0
0
200
400
600
f − Frequency − MHz
Figure 14.
800
0
400
800
1200
Data Rate − Mbps
Figure 15.
1600
SN65LVDS122
SN65LVDT122
www.ti.com
SLLS525B – MAY 2002 – REVISED JUNE 2004
TYPICAL CHARACTERISTICS (continued)
PEAK-TO-PEAK JITTER
vs
TEMPERATURE
PEAK-TO-PEAK JITTER
vs
DATA RATE
50
VCC = 3.3 V
TA = 25°C
VIC = 1.2 V
|V ID |= 200 m V
Input = PRBS 223 −1
90
Peak-To-Peak Jitter − ps
Peak-To-Peak Jitter - ps
40
100
VCC = 3.3 V
TA = 25°C
VIC = 1.2 V
VID = 200 mV
Input = 1.5 Gpbs, PRBS 223 −1
30
20
10
80
70
60
50
40
30
20
10
0
0
−40 −20
0
20
40
60
80
TA − Free Air Temperature − °C
Figure 16.
LVDS122
622 Mbps, 223– 1 PRBS
100
0
500 1000 1500 2000 2500 3000 3500
Data Rate − Mbps
Figure 17.
LVDS122
1.5 Gbps, 223– 1 PRBS
VCC = 3.3 V
TA = 25°C
VID = 200 mV
Horizontal Scale= 200 ps/div
LVPECL-to-LVDS
Figure 18.
VCC = 3.3 V
TA = 25°C
VID = 200 mV
Horizontal Scale= 100 ps/div
LVPECL-to-LVDS
Figure 19.
11
SN65LVDS122
SN65LVDT122
www.ti.com
SLLS525B – MAY 2002 – REVISED JUNE 2004
TYPICAL CHARACTERISTICS (continued)
LVDS122
622 Mbps, 223– 1 PRBS
LVDS122
1.5 Gbps, 223– 1 PRBS
VCC = 3.3 V
TA = 25°C
VID = 200 mV
VCC = 3.3 V
TA = 25°C
VID = 200 mV
Horizontal Scale= 200 ps/div
LVDS-to-LVDS
Horizontal Scale= 100 ps/div
LVDS-to-LVDS
Figure 20.
Power Supply 1
Figure 21.
+
3.3 V
−
Power Supply 2
+
1.22 V
−
J3
DUT
GND
J2
EVM
GND
J1
VCC
J4
J5
J6
100 Ω
J7
50 Ω
DUT
Pattern
Generator
Matched
Cables
SMA to SMA
50 Ω
Matched
Cables
SMA to SMA
EVM
Oscilloscope
Figure 22. Jitter Setup Connections for SN65LVDS122
12
SN65LVDS122
SN65LVDT122
www.ti.com
SLLS525B – MAY 2002 – REVISED JUNE 2004
APPLICATION INFORMATION
TYPICAL APPLICATION CIRCUITS (ECL, PECL, LVDS, etc.)
50 Ω
3.3 V or 5 V
3.3 V
SN65LVDS122
A
ECL
B
50 Ω
50 Ω
50 Ω
VTT = VCC −2 V
VTT
Figure 23. Low-Voltage Positive Emitter-Coupled Logic (LVPECL)
3.3 V
50 Ω
50 Ω
3.3 V
3.3 V
SN65LVDS122
A
CML
B
50 Ω
50 Ω
3.3 V
Figure 24. Current-Mode Logic (CML)
3.3 V
SN65LVDS122
3.3 V
50 Ω
A
ECL
B
50 Ω
1.1 kΩ
VTT
1.5 kΩ
VTT = VCC −2 V
VCC
Figure 25. Single-Ended (LVPECL)
3.3 V or 5 V
50 Ω
3.3 V
SN65LVDS122
A
100 Ω
LVDS
B
50 Ω
Figure 26. Low-Voltage Differential Signaling (LVDS)
13
PACKAGE OPTION ADDENDUM
www.ti.com
8-Jan-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
SN65LVDS122D
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65LVDS122DG4
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65LVDS122DR
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65LVDS122DRG4
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65LVDS122PW
ACTIVE
TSSOP
PW
16
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65LVDS122PWG4
ACTIVE
TSSOP
PW
16
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65LVDS122PWR
ACTIVE
TSSOP
PW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65LVDS122PWRG4
ACTIVE
TSSOP
PW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65LVDT122D
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65LVDT122DG4
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65LVDT122DR
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65LVDT122DRG4
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65LVDT122PW
ACTIVE
TSSOP
PW
16
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65LVDT122PWG4
ACTIVE
TSSOP
PW
16
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65LVDT122PWR
ACTIVE
TSSOP
PW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65LVDT122PWRG4
ACTIVE
TSSOP
PW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
8-Jan-2007
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Jun-2007
TAPE AND REEL INFORMATION
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
Device
16-Jun-2007
Package Pins
Site
Reel
Diameter
(mm)
Reel
Width
(mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
SN65LVDS122DR
D
16
TAI
330
16
6.5
10.3
2.1
8
16
Q1
SN65LVDS122PWR
PW
16
TAI
330
12
6.67
5.4
1.6
8
12
Q1
SN65LVDT122DR
D
16
TAI
330
16
6.5
10.3
2.1
8
16
Q1
SN65LVDT122PWR
PW
16
TAI
330
12
6.67
5.4
1.6
8
12
Q1
TAPE AND REEL BOX INFORMATION
Device
Package
Pins
Site
Length (mm)
Width (mm)
Height (mm)
SN65LVDS122DR
D
16
TAI
346.0
346.0
33.0
SN65LVDS122PWR
PW
16
TAI
535.4
346.0
48.3
SN65LVDT122DR
D
16
TAI
346.0
346.0
33.0
SN65LVDT122PWR
PW
16
TAI
535.4
346.0
48.3
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Jun-2007
Pack Materials-Page 3
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties
may be subject to additional restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Telephony
www.ti.com/telephony
Low Power
Wireless
www.ti.com/lpw
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated