® SP3490/SP3491 +3.3V Low Power Full Duplex RS-485 Transceivers with 10Mbps Data Rate ■ Full Duplex RS-485 and RS-422 Transceivers ■ Operates from a single +3.3V supply ■ Interoperable with +5.0V logic ■ Driver/Receiver Tri-state Enable Lines (SP3491) ■ -7V to +12V Common-Mode Input Voltage Range ■ +200mV Receiver Input Sensitivity ■ Allows up to 32 transceivers on the serial bus ■ Compatibility with LTC490 and SN75179 (SP3490) ■ Compatibility with LTC491 and SN75180 (SP3491) DESCRIPTION The SP3490 and the SP3491 are +3.3V low power full duplex transceivers that meet the specifications of the RS-485 and RS-422 serial protocols. These devices are pin-to-pin compatible with the Sipex SP490 and SP491 devices as well as popular industry standards. The SP3490 and the SP3491 feature Sipex's BiCMOS process, allowing low power operation without sacrificing performance. The SP3490 and SP3491 meet the electrical specifications of RS-485 and RS-422 serial protocols up to 10Mbps under load. The SP3491 is identical to the SP3490 with the addition of driver and receiver tri-state enable lines. 14 Vcc 13 NC 12 A NC 1 R 2 Vcc 1 R 8 A R 2 11 B REB 3 R 7 B DE 4 6 Z D 3 10 Z D 5 D 9 Y GND 6 GND 7 SP3490 Rev. 10/11/02 D 5 Y GND 4 8 NC SP3491 SP3490/3491 Low Power Full-Duplex RS485 Transceivers 1 © Copyright 2002 Sipex Corporation ABSOLUTE MAXIMUM RATINGS These are stress ratings only and functional operation of the device at these ratings or any other above those indicated in the operation sections of the specifications below is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. VCC ............................................................................................. +6.0V Input Voltages Drivers ............................................................... -0.3V to +6.0V Receivers ......................................................................... ±14V Output Voltages Drivers .............................................................................. ±14V Receivers .......................................................... -0.3V to +6.0V Storage Temperature ................................................... -65˚C to +150˚ Power Dissipation per Package 8-pin NSOIC (derate 6.90mW/oC above +70oC) ..................... 600mW 8-pin PDIP (derate 11.8mW/oC above +70oC) ...................... 1000mW 14-pin NSOIC (derate 8.33mW/oC above +70oC) ................... 700mW 14-pin PDIP (derate 14.3mW/oC above +70oC) .................... 1200mW SPECIFICATIONS TAMB = TMIN to TMAX and VCC = 3.3V ± 5% unless otherwise noted. PARAMETERS SP3490 DRIVER DC Characteristics Differential Output Voltage Differential Output Voltage Differential Output Voltage Change in Magnitude of Driver Differential Output Voltage for Complimentary States Driver Common-Mode Output Voltage Input High Voltage Input Low Voltage Input Current Driver Short-Circuit Current VOUT = HIGH VOUT = LOW MIN. TYP. MAX. UNITS CONDITIONS GND 2 VCC VCC Volts Volts 1.5 VCC Volts Unloaded; R = ∞ Ω; Figure 1 With Load; R = 50Ω; (RS-422); Figure 1 With Load; R = 27Ω; (RS-485); Figure 1 0.2 Volts R = 27Ω or R = 50Ω; Figure 1 3 R = 27Ω or R = 50Ω; Figure 1 0.8 +10 Volts Volts Volts µA +250 +250 mA mA 2.0 -7V < VO < +12V -7V < VO < +12V SP3490 DRIVER AC Characteristics Maximum Data Rate Driver Input to Output, tPLH 10 20 40 60 Mbps ns R=27Ω, Figures 2 and 8 Driver Input to Output, tPHL 20 40 60 ns R=27Ω, Figures 2 and 8 ns tPHL(Y) - tPLH(Y) , tPHL(Z) - tPLH(Z) , Figures 2 and 8 From 10% to 90%; Figures 3 and 9 Differential Driver Skew 2 Driver Rise or Fall Time 5 SP3490 RECEIVER DC Characteristics Differential Input Threshold 0.2 Input Hysteresis Output Voltage High VCC-0.4 Output Voltage Low Input Resistance 12 Input Current (A, B); VIN = 12V Input Current (A, B); VIN = -7V Short-Circuit Current Rev. 10/11/02 20 ns +0.2 Volts mV Volts Volts kΩ mA mA mA 25 0.4 15 1.0 -0.8 60 SP3490/3491 Low Power Full-Duplex RS485 Transceivers 2 -7V < VCM < 12V VCM = 0V IO = -1.5mA, VID = +200mV IO = +2.5mA, VID = -200mV -7V < VCM ≤ 12V VIN = 12V VIN = -7V 0V < VO < VCC © Copyright 2002 Sipex Corporation SPECIFICATIONS (continued) TAMB = TMIN to TMAX and VCC = 3.3V ± 5% unless otherwise noted. PARAMETERS SP3490 RECEIVER AC Characteristics Maximum Data Rate Receiver Input to Output, tPLH MIN. TYP. MAX. UNITS 10 40 70 120 85 Mbps ns ns Figures 6 and 11 TAMB = 25oC, VCC = 3.3V, Figures 6 and 11 Receiver Input to Output, tPHL 40 70 120 85 ns ns Figures 6 and 11 TAMB = 25oC, VCC = 3.3V, Figures 6 and 11 ns tPHL(A) - tPLH(A) , tPHL(B) - tPLH(B) , Figures 6 and 11 Differential Receiver Skew 4 POWER REQUIREMENTS Supply Voltage +3.0 Supply Current 1000 800 +3.6 Volts 2000 1500 µA CONDITIONS DE = VCC DE = 0 VDM R RL = 27Ω S1 VOD D D R VCC GENERATOR (NOTE 1) VOC OUT 50Ω CL = 15pF (NOTE 2) VCC VOM = VOH + VOL 2 1.5V Figure 2. Driver Propagation Delay Test Circuit Figure 1. Driver DC Test Load Circuit S1 D CL RL = 60Ω D GENERATOR (NOTE 1) OUT OUT RL = 110Ω CL = 50pF (NOTE 2) GENERATOR (NOTE 1) 50Ω VCC 50Ω VOM = VOH + VOL 2 CL = 15pF (NOTE 2) 1.5V Figure 4. Driver Enable and Disable Timing Circuit, Output HIGH Figure 3. Driver Differential Output Delay and Transition Time Circuit VCC RL = 110Ω VID S1 0V OR 3V D GENERATOR (NOTE 1) OUT R OUT 50Ω CL = 15pF (NOTE 2) CL = 50pF (NOTE 2) GENERATOR (NOTE 1) 50Ω 1.5V 0V Figure 6. Receiver Propagation Delay Test Circuit Figure 5. Driver Enable and Disable Timing Circuit, Output LOW Rev. 10/11/02 VOM = VCC 2 SP3490/3491 Low Power Full-Duplex RS485 Transceivers 3 © Copyright 2002 Sipex Corporation 3V INPUT 1.5V 1.5V tPLH tPHL 0V S1 S3 1.5V VID VOH VCC 1k -1.5V R VOL CL = 15pF (NOTE 2) GENERATOR (NOTE 1) VOM VOM Y OUTPUT S2 tPHL 50Ω tPLH VOH Z OUTPUT VOM VOM VOL VOM = VOH + VOL ≈ 1.5V 2 Figure 7. Receiver Enable and Disable Timing Circuit Figure 8. Driver Propagation Delay Waveforms 3V 1.5V 1.5V DE 3V 0V IN 1.5V 1.5V VOH 0V tDPLH 0.25V VOM 0V 2.0V 90% 90% 50% 10% OUT OUTPUT HIGH tDPHL tPHZ tPZH 50% 10% VCC OUTPUT LOW -2.0V tR tPZL tPLZ VOM VOL tF 0.25V VOM = VOH + VOL ≈ 1.5V 2 Figure 9. Driver Differential Output Delay and Transition Time Waveforms Figure 10. Driver Enable and Disable Timing Waveforms 3V INPUT 1.5V 1.5V tRPLH tRPHL 0V VCC OUTPUT VOM VOM 0V VOM = VCC 2 Figure 11. Receiver Propagation Delay Waveforms Rev. 10/11/02 SP3490/3491 Low Power Full-Duplex RS485 Transceivers 4 © Copyright 2002 Sipex Corporation SPECIFICATIONS TAMB = TMIN to TMAX and VCC = +3.3V ± 5% unless otherwise noted. PARAMETERS SP3491 DRIVER DC Characteristics Differential Output Voltage Differential Output Voltage Differential Output Voltage Change in Magnitude of Driver Differential Output Voltage for Complimentary States Driver Common-Mode Output Voltage Input HIGH Voltage Input LOW Voltage Input Current Driver Short-Circuit Current VOUT = HIGH VOUT = LOW MIN. TYP. MAX. UNITS GND 2 VCC VCC Volts Volts 1.5 VCC Volts Unloaded; R = ∞; Figure 1 With Load; R = 50Ω; (RS-422); Figure 1 With Load; R = 27Ω; (RS-485); Figure 1 0.2 Volts R = 27Ω or R = 50Ω; Figure 1 3 0.8 +10 Volts Volts Volts µA R = 27Ω or R = 50Ω; Figure 1 Applies to D, REB, DE Applies to D, REB, DE Applies to D, REB, DE +250 +250 mA mA -7V < VO < +12V -7V < VO < +12V 2.0 CONDITIONS SP3491 DRIVER AC Characteristics Maximum Data Rate Driver Input to Output, tPLH 10 20 40 60 Mbps ns Figures 2 and 8 Driver Input to Output, tPHL 20 40 60 ns Figures 2 and 8 ns tPHL(Y) - tPLH(Y) , tPHL(Z) - tPLH(Z) , Figures 2 and 8 Differential Driver Skew 2 Driver Rise or Fall Time 5 20 ns From 10% to 90%; Figures 3 and 9 Driver Enable to Output HIGH 52 120 ns Figures 4 and 10 Driver Enable to Output LOW 60 120 ns Figures 5 and 10 Driver Disable from LOW 40 120 ns Figures 5 and 10 Driver Disable from HIGH 60 120 ns Figures 4 and 10 NOTE 1: The input pulse is supplied by a generator with the following characteristics: PRR=250KHz, 50% duty cycle, tr < 6.0ns, Z0=50Ω. NOTE 2: CL includes probe and stray capacitance. Rev. 10/11/02 SP3490/3491 Low Power Full-Duplex RS485 Transceivers 5 © Copyright 2002 Sipex Corporation SPECIFICATIONS (continued) TAMB = TMIN to TMAX and VCC = +3.3V ± 5% unless otherwise noted. PARAMETERS MIN. SP3491 RECEIVER DC Characteristics Differential Input Threshold -0.2 Input Hysteresis Output Voltage HIGH VCC-0.4 Output Voltage LOW Three State (high impedance) Output Current Input Resistance 12 Input Current (A, B); VIN = 12V Input Current (A, B); VIN = -7V Short-Circuit Current SP3491 RECEIVER AC Characteristics Maximum Data Rate 10 Receiver Input to Output, tPLH 40 Receiver Input to Output, tPHL 40 TYP. MAX. UNITS +0.2 Volts mV Volts Volts -7V < VCM < 12V VCM = 0V IO = -1.5mA, VID = +200mV IO = +2.5mA, VID = -200mV 1.0 -0.8 60 µA kΩ mA mA mA 0V < VO < VCC; REB = VCC -7V < VCM < 12V DE = 0V, VCC = 0V or +3.6V, VIN = 12V DE = 0V, VCC = 0V or +3.6V, VIN = -7V 0V < VO < VCC 70 120 85 Mbps ns ns REB = 0V, DE = VCC Figures 6 & 11 TAMB = +25oC, VCC = +3.3V, Figures 6 and 11 70 120 85 ns ns Figures 6 & 11 TAMB = +25oC, VCC = +3.3V, Figures 6 and 11 ns tPHL(A) - tPLH(A) , tPHL(B) - tPLH(B) , Figures 6 & 11 Figures 7 and 12; S1 closed, S2 open Figures 7 and 12; S2 closed, S1 open Figures 7 and 12; S1 closed, S2 open Figures 7 and 12; S2 closed, S1 open 25 0.4 +1 15 Differential Receiver Skew 4 Receiver Enable to Output LOW Receiver Enable to Output HIGH Receiver Disable from LOW Receiver Disable from HIGH POWER REQUIREMENTS Supply Voltage +3.0 Supply Current 65 65 65 65 150 150 200 200 ns ns ns ns 1000 800 +3.6 2000 1500 Volts µA µA 3V 3V 1.5V 1.5V 0V tPRHZ VOH 1.5V 1.5V REB 0V OUTPUT REB, D = 0V or VCC; DE = VCC DE=0V S1 is closed S2 is open S3 = -1.5V S1 is open S2 is closed S3 = 1.5V REB CONDITIONS tPRZH tPRSH tPRLZ tPRZL tPRSL VCC 10% 1.5V 1.5V OUTPUT 0V VOL 10% Figure 12. Receiver Enable and Disable Waveforms Rev. 10/11/02 SP3490/3491 Low Power Full-Duplex RS485 Transceivers 6 © Copyright 2002 Sipex Corporation PIN FUNCTION - SP3490 Vcc 1 Pin 1 - VCC - Positive supply +3.00 < VCC < +3.60 Pin 2 - R - Receiver output. Pin 3 - D - Driver input. Pin 4 - GND - Ground connection. Pin 5 - Y - Non-inverting driver output. Pin 6 - Z - Inverting driver output. Pin 7 - B - Inverting receiver input. Pin 8 - A - Non-inverting receiver input. 8 A R 2 R 7 B 6 Z D 3 D GND 4 5 Y Figure 13. Pinout for the SP3490 PIN FUNCTION - SP3491 14 Vcc 13 NC 12 A NC 1 R 2 R Pin 1 - NC - No connect. Pin 2 - R - Receiver output. Pin 3 - REB - Receiver output enable active LOW. Pin 4 - DE - Driver output enable active HIGH. Pin 5 - D - Driver input. Pin 6 - GND - Ground connection. Pin 7 - GND - Ground connection. Pin 8 - NC - No connect. Pin 9 - Y - Non-inverting driver output. Pin 10 - Z - Inverting driver output. Pin 11 - B - Inverting receiver input. Pin 12 - A - Non-inverting receiver input. Pin 13 - NC - No connect. Pin 14 - VCC - Positive supply +3.00 < VCC< +3.60 11 B REB 3 DE 4 10 Z D 5 D GND 6 GND 7 9 Y 8 NC Figure 14. Pinout for the SP3491 Rev. 10/11/02 SP3490/3491 Low Power Full-Duplex RS485 Transceivers 7 © Copyright 2002 Sipex Corporation DESCRIPTION Receiver The SP3490 and the SP3491 are two members in the family of +3.3V low power full duplex transceivers that meet the electrical specifications of the RS-485 and RS-422 serial protocols. These devices are pin-to-pin compatible with the Sipex SP490 and the SP491 devices as well as popular industry standards. The SP3490 and the SP3491 feature Sipex's BiCMOS process allowing low power operation without sacrificing performance. The receivers for the SP3490 and SP3491 have differential inputs with an input sensitivity as low as ±100mV. Input impedance of the receivers is typically 15kΩ (12kΩ minimum). A wide common mode range of -7V to +12V allows for large ground potential differences between systems. The receivers for both the SP3490 and SP3491 are equipped with a fail-safe feature that guarantees the receiver output will be in a high state when the input is left unconnected. Driver The receiver of the SP3491 has a receiver enable control line which is active low. A logic low on REB (pin 3) of the SP3491 will enable the differential receiver. A logic high on REB (pin 3) of the SP3491 will tri-state the receiver. The drivers for both the SP3490 and SP3491 have differential outputs. The typical voltage output swing with no load will be 0 volts to VCC. With a load of 54Ω across the differential outputs, the driver maintains greater than 1.5V voltage levels. The driver of the SP3491 has a driver enable control line which is active high. A logic high on DE (pin 4) of the SP3491 will enable the differential driver outputs. A logic low on DE (pin 4) of the SP3491 will tri-state the driver outputs. The SP3490 does not have a driver enable. Rev. 10/11/02 SP3490/3491 Low Power Full-Duplex RS485 Transceivers 8 © Copyright 2002 Sipex Corporation PACKAGE: PLASTIC DUAL–IN–LINE (NARROW) E1 E D1 = 0.005" min. (0.127 min.) A1 = 0.015" min. (0.381min.) D A = 0.210" max. (5.334 max). C A2 e = 0.100 BSC (2.540 BSC) B1 B Ø L eA = 0.300 BSC (7.620 BSC) ALTERNATE END PINS (BOTH ENDS) DIMENSIONS (Inches) Minimum/Maximum (mm) Rev. 10/11/02 8–PIN 14–PIN A2 0.115/0.195 (2.921/4.953) 0.115/0.195 (2.921/4.953) B 0.014/0.022 (0.356/0.559) 0.014/0.022 (0.356/0.559) B1 0.045/0.070 (1.143/1.778) 0.045/0.070 (1.143/1.778) C 0.008/0.014 (0.203/0.356) 0.008/0.014 (0.203/0.356) D 0.355/0.400 0.735/0.775 (9.017/10.160) (18.669/19.685) E 0.300/0.325 (7.620/8.255) 0.300/0.325 (7.620/8.255) E1 0.240/0.280 (6.096/7.112) 0.240/0.280 (6.096/7.112) L 0.115/0.150 (2.921/3.810) 0.115/0.150 (2.921/3.810) Ø 0°/ 15° (0°/15°) 0°/ 15° (0°/15°) SP3490/3491 Low Power Full-Duplex RS485 Transceivers 9 © Copyright 2002 Sipex Corporation PACKAGE: PLASTIC SMALL OUTLINE (SOIC) (NARROW) E H h x 45° D A Ø e B A1 L DIMENSIONS (Inches) Minimum/Maximum (mm) Rev. 10/11/02 8–PIN 14–PIN A 0.053/0.069 (1.346/1.748) 0.053/0.069 (1.346/1.748) A1 0.004/0.010 (0.102/0.249 0.004/0.010 (0.102/0.249) B 0.014/0.019 (0.35/0.49) 0.013/0.020 (0.330/0.508) D 0.189/0.197 (4.80/5.00) 0.337/0.344 (8.552/8.748) E 0.150/0.157 (3.802/3.988) 0.150/0.157 (3.802/3.988) e 0.050 BSC (1.270 BSC) 0.050 BSC (1.270 BSC) H 0.228/0.244 (5.801/6.198) 0.228/0.244 (5.801/6.198) h 0.010/0.020 (0.254/0.498) 0.010/0.020 (0.254/0.498) L 0.016/0.050 (0.406/1.270) 0.016/0.050 (0.406/1.270) Ø 0°/8° (0°/8°) 0°/8° (0°/8°) SP3490/3491 Low Power Full-Duplex RS485 Transceivers 10 © Copyright 2002 Sipex Corporation ORDERING INFORMATION Model SP3490CN SP3490CP SP3490EN SP3490EP SP3491CN SP3491CP SP3491EN. SP3491EP ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Temperature Range 0˚C to +70˚C 0˚C to +70˚C -40˚C to +85˚C -40˚C to +85˚C ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 0˚C to +70˚C 0˚C to +70˚C -40˚C to +85˚C -40˚C to +85˚C ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 14-Pin NSOIC 14-Pin DIP 14-Pin NSOIC 14-Pin DIP ○ ○ Package 8-Pin NSOIC 8-Pin DIP 8-Pin NSOIC 8-Pin DIP ○ ○ ○ Please consult the factory for pricing and availability on a Tape-On-Reel option. Corporation Sipex Corporation Headquarters and Sales Office 233 South Hillview Drive Milpitas, CA 95035 TEL: (408) 934-7500 FAX: (408) 935-7600 Sales Office 22 Linnell Circle Billerica, MA 01821 TEL: (978) 667-8700 FAX: (978) 670-9001 e-mail: [email protected] Sipex Corporation reserves the right to make changes to any products described herein. Sipex does not assume any liability arising out of the application or use of any product or circuit described hereing; neither does it convey any license under its patent rights nor the rights of others. Rev. 10/11/02 SP3490/3491 Low Power Full-Duplex RS485 Transceivers 11 © Copyright 2002 Sipex Corporation