Micrel, Inc. SY10EL05 SY100EL05 SY10EL05 2-INPUT DIFFERENTIAL AND/NAND FEATURES SY100EL05 DESCRIPTION ■ 275ps propagation delay ■ High bandwidth output transitions ■ Internal 75KΩ input pull-down resistors The SY10/100EL05 are 2-input differential AND/NAND gates. These devices are functionally equivalent to the E404 devices, with higher performance capabilities. With propagation delays and output transition times significantly faster than the E404, the EL05 is ideally suited for those applications which require the ultimate in AC performance. Because a negative 2-input NAND is equivalent to a 2-input OR function with inverted inputs, the differential inputs and outputs of the device allows the EL05 to also be used as a 2-input differential OR/NOR gate. The differential inputs employ clamp circuitry so that, under open conditions (pulled down to VEE), the input to the AND gate will be HIGH. In this way, if one set of inputs is open, the gate will remain active to the other input. ■ Available in 8-pin SOIC package PIN NAMES Pin M9999-031006 [email protected] or (408) 955-1690 Function D0, D1 Data Inputs Q Data Outputs Rev.: G 1 1 Amendment: /0 Issue Date: March 2006 SY10EL05 SY100EL05 Micrel, Inc. PACKAGE/ORDERING INFORMATION Ordering Information(1) D0 1 8 VCC D0 2 7 Q D1 3 6 Q D1 5 4 VEE 8-Pin SOIC (Z8-1) Part Number Package Type Operating Range Package Marking SY10EL05ZC Z8-1 Commercial HEL05 Sn-Pb SY10EL05ZCTR(2) Z8-1 Commercial HEL05 Sn-Pb SY100EL05ZC Z8-1 Commercial XEL05 Sn-Pb SY100EL05ZCTR(2) Z8-1 Commercial XEL05 Sn-Pb SY10EL05ZI Z8-1 Industrial HEL05 Sn-Pb SY10EL05ZITR(2) Z8-1 Industrial HEL05 Sn-Pb SY100EL05ZI Z8-1 Industrial XEL05 Sn-Pb SY100EL05ZITR(2) Z8-1 Industrial XEL05 Sn-Pb SY10EL05ZG(3) Z8-1 Industrial HEL05 with Pb-Free bar-line indicator Pb-Free NiPdAu SY10EL05ZGTR(2, 3) Z8-1 Industrial HEL05 with Pb-Free bar-line indicator Pb-Free NiPdAu SY100EL05ZG(3) Z8-1 Industrial XEL05 with Pb-Free bar-line indicator Pb-Free NiPdAu SY100EL05ZGTR(2, 3) Z8-1 Industrial XEL05 with Pb-Free bar-line indicator Pb-Free NiPdAu Notes: 1. Contact factory for die availability. Dice are guaranteed at TA = 25°C, DC Electricals only. 2. Tape and Reel. 3. Pb-Free package is recommended for new designs. M9999-031006 [email protected] or (408) 955-1690 Lead Finish 2 SY10EL05 SY100EL05 Micrel, Inc. DC ELECTRICAL CHARACTERISTICS VEE = VEE (Min.) to VEE (Max.); VCC = GND TA = –40°C Symbol IEE VEE IIH TA = 0°C TA = +25°C TA = +85°C Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Power Supply Current 10EL 100EL — — 18 18 22 22 14 14 18 18 22 22 14 14 18 18 22 22 14 16 18 21 22 25 –5.2 –4.5 –5.5 –5.5 –4.75 –4.20 –5.2 –4.5 –5.5 –5.5 –4.75 –4.20 –5.2 –4.5 –5.5 –5.5 –4.75 –4.20 –5.2 –4.5 –5.5 –5.5 — 150 — — 150 — — 150 — — 150 mA Power Supply Voltage 10EL –4.75 100EL –4.20 Input HIGH Current Unit — V µA AC ELECTRICAL CHARACTERISTICS VEE = VEE (Min.) to VEE (Max.); VCC = GND TA = –40°C Symbol Parameter TA = 0°C TA = +25°C TA = +85°C Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit tPD Propagation Delay to Output D 135 260 440 185 275 390 185 275 390 215 305 420 ps VPP Minimum Input Swing(1) 150 — — 150 — — 150 — — 150 — — mV (2) — –0.4 (2) — –0.4 (2) — –0.4 (2) — –0.4 V 225 350 100 225 350 100 225 350 100 225 350 ps Range(2) VCMR Common Mode tr tf Output Rise/Fall Times Q 100 (20% to 80%) NOTES: 1. Minimum input swing for which AC parameters are guaranteed. The device has a DC gain of ≈40. 2. The CMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPP min. and 1V. The lower end of the CMR range is dependent on VEE and is equal to VEE + 3.0V. M9999-031006 [email protected] or (408) 955-1690 3 SY10EL05 SY100EL05 Micrel, Inc. 8-PIN SOIC .150" WIDE (Z8-1) Rev. 03 MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 TEL + 1 (408) 944-0800 FAX + 1 (408) 474-1000 WEB USA http://www.micrel.com The information furnished by Micrel in this datasheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2006 Micrel, Incorporated. M9999-031006 [email protected] or (408) 955-1690 4