TC4066BP/BF/BFN/BFT TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC4066BP,TC4066BF,TC4066BFN,TC4066BFT TC4066B Quad Bilateral Switch TC4066B contains four independent circuits of bidirectional switches. When control input CONT is set to “H” level, the impedance between input and output of the switch becomes low and when it is set to “L” level, the impedance becomes high. This can be applied for switching of analog signals and digital signals. • ON-resistance, Ron 250 Ω (typ.): VDD − VSS = 5 V 110 Ω (typ.): VDD − VSS = 10 V 70 Ω (typ.): VDD − VSS = 15 V • OFF-resistance, Roff Roff (typ.) > 109 Ω Note: xxxFN (JEDEC SOP) is not available in Japan. TC4066BP TC4066BF Pin Assignment IN/OUT 1 1 14 VDD OUT/IN 1 2 13 CONT 1 OUT/IN 2 3 12 CONT 4 IN/OUT 2 4 11 IN/OUT 4 CONT 2 5 10 OUT/IN 4 CONT 3 6 9 OUT/IN 3 VSS 7 8 IN/OUT 3 TC4066BFN (top view) TC4066BFT Truth Table Control Note: Impedance between IN/OUT-OUT/IN (Note) 2 H 0.5 to 5 × 10 Ω L >10 Ω 9 See static electrical characteristics Weight DIP14-P-300-2.54 SOP14-P-300-1.27A SOL14-P-150-1.27 TSSOP14-P-0044-0.65A 1 : 0.96 g (typ.) : 0.18 g (typ.) : 0.12 g (typ.) : 0.06 g (typ.) 2007-10-01 TC4066BP/BF/BFN/BFT Logic Diagram 1/4 TC4066B I/O O/I CONT Absolute Maximum Ratings (Note) Characteristics Symbol Rating Unit DC supply voltage VDD VSS − 0.5 to VSS + 20 V Control input voltage VCIN VSS − 0.5 to VDD + 0.5 V Switch I/O voltage VI/O VSS − 0.5 to VDD + 0.5 V Potential difference across I/O during ON II/O ±0.5 V Control input current ICIN ±10 mA Power dissipation PD 300 (DIP)/180 (SOIC) mW Operating temperature range Topr −40 to 85 °C Storage temperature range Tstg −65 to 150 °C Note: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Operating Ranges (VSS = 0 V) (Note) Characteristics DC supply voltage Input voltage Note: Symbol Test Condition Min Typ. Max Unit VDD ⎯ 3 ⎯ 18 V VDD/VOUT ⎯ 0 ⎯ VDD V The operating ranges must be maintained to ensure the normal operation of the device. Unused control inputs must be tied to either VDD or VSS. 2 2007-10-01 TC4066BP/BF/BFN/BFT Static Electrical Characteristics (in case not specifically appointed, VSS = 0 V) −40°C Test Condition Characteristics Control input high voltage Control input low voltage On-state resistance VIH VIL RON ΔOn-state resistance (between any 2 switches) Input/output leakage current Quiescent supply current “H” level Input current “L” level Note: Symbol |IIS| < 10 μA |IIS| < 10 μA 0 ≤ VIS ≤ VDD RL = 10 kΩ ⎯ RONΔ IOFF IDD VIN = 18 V, VOUT = 0 V VIN = 0 V, VOUT = 18 V VIN = VSS, VDD (Note) 25°C 85°C VDD (V) Min Max Min Typ. Max Min Max 5 3.5 ⎯ 3.5 2.75 ⎯ 3.5 ⎯ 10 7.0 ⎯ 7.0 5.50 ⎯ 7.0 ⎯ 15 11.0 ⎯ 11.0 8.25 ⎯ 11.0 ⎯ 5 ⎯ 1.5 ⎯ 2.25 1.5 ⎯ 1.5 10 ⎯ 3.0 ⎯ 4.50 3.0 ⎯ 3.0 15 ⎯ 4.0 ⎯ 6.75 4.0 ⎯ 4.0 5 ⎯ 800 ⎯ 290 950 ⎯ 1200 10 ⎯ 210 ⎯ 120 250 ⎯ 300 15 ⎯ 140 ⎯ 85 160 ⎯ 200 5 ⎯ ⎯ ⎯ 10 ⎯ ⎯ ⎯ 10 ⎯ ⎯ ⎯ 6 ⎯ ⎯ ⎯ 15 ⎯ ⎯ ⎯ 4 ⎯ ⎯ ⎯ 18 ⎯ ±100 ⎯ ±0.1 ±100 ⎯ ±1000 18 ⎯ ±100 ⎯ ±0.1 ±100 ⎯ ±1000 5 ⎯ 0.25 ⎯ 0.001 0.25 ⎯ 7.5 10 ⎯ 0.50 ⎯ 0.001 0.50 ⎯ 15.0 15 ⎯ 1.00 ⎯ 0.002 1.00 ⎯ 30.0 0.1 ⎯ 1.0 −0.1 ⎯ −1.0 5 IIH VIH = 18 V 18 ⎯ 0.1 ⎯ 10− IIL VIL = 0 V 18 ⎯ −0.1 ⎯ −10− Unit V V Ω Ω nA μA μA 5 All valid input combinations. 3 2007-10-01 TC4066BP/BF/BFN/BFT Dynamic Electrical Characteristics (Ta = 25°C, VSS = 0 V, CL = 50 pF) Test Condition Characteristics Phase difference between input to output Symbol φI-O VSS VDD (V) (V) CL = 50 pF Propagation delay time tpZL RL = 1 kΩ (control-OUT) tpZH CL = 50 pF Propagation delay time tpLZ RL = 1 kΩ (control -OUT) tpHZ CL = 50 pF Max control input repetition rate −3dB cutoff frequency fmax (C) fmax (I-O) Total harmonic distortion ⎯ −50dB feed through frequency −50dB crosstalk frequency Crosstalk (control-OUT) Input capacitance Feed through capacitance RL = 1 kΩ CL = 50 pF RL = 1 kΩ CL = 15 pF (Note 1) RL = 10 kΩ Min Typ. Max Unit 0 5 ⎯ 15 40 0 10 ⎯ 8 20 0 15 ⎯ 5 15 0 5 ⎯ 55 120 0 10 ⎯ 25 40 0 15 ⎯ 20 30 0 5 ⎯ 45 80 0 10 ⎯ 30 70 0 15 ⎯ 25 60 0 5 ⎯ 10 ⎯ 0 10 ⎯ 12 ⎯ 0 15 ⎯ 12 ⎯ −5 5 ⎯ 30 ⎯ MHz −5 5 ⎯ 0.03 ⎯ % ns ns ns MHz f = 1 kHz (Note 2) ⎯ RL = 1 kΩ (Note 3) −5 5 ⎯ 600 ⎯ kHz ⎯ RL = 1 kΩ (Note 4) −5 5 ⎯ 1 ⎯ MHz RIN = 1 kΩ 0 5 ⎯ 200 ⎯ ROUT = 10 kΩ 0 10 ⎯ 400 ⎯ CL = 15 pF 0 15 ⎯ 600 ⎯ Control input ⎯ 5 7.5 Switch I/O ⎯ 10 ⎯ ⎯ 0.5 ⎯ ⎯ CIN ⎯ CIN-OUT Note 1: Sine wave of ±2.5 p-p shall be used for Vis and the frequency of 20 log 10 mV pF pF VOS = −3dB shall be fmax. Vis Note 2: Vis shall be sine wave of ±2.5 Vp-p Note 3: Sine wave of ±2.5 Vp-p shall be used for Vis and the frequency of 20 log 10 VOUT Vis = −50dB shall be VOUT Vis = −50dB shall be feed-through. Note 4: Sine wave of ±2.5 Vp-p shall be used for Vis and the frequency of 20 log 10 crosstalk. 4 2007-10-01 TC4066BP/BF/BFN/BFT Circuit for Measurement of Electrical Characteristics 1. φI-O I/O-O/I tr = 20 ns WAVEFORM VDD tf = 20 ns I/O I/O O/I 90% 50% 10% 90% 50% 10% φI-O φI-O VDD VSS P.G. CL = 50 pF C VOH O/I 50% 50% VOL 2. tpZH, tpHL, tpLZ, tpHZ (CONTROL-OUT) WAVEFORM VDD Control I/O O/I O/I RL = 1 kΩ CL = 50 pF C 10% 90% 50% 90% 50% 10% SW2 SW1 P.G. tr = 20 ns tf = 20 ns SW1 = VDD SW2 = VSS 90% 50% tpZH O/I tpHZ SW1 = VSS SW2 = VDD 50% VDD VSS VOH VOL VOH 10% VOL tpLZ tpZL 3. RON VDD VIN O/I I/O VOUT RON = 10 × (VIN − VOUT ) [kΩ] VOUT RL = 10 kΩ C VSS 4. fmax (C) tr = 20 ns VDD Control O/I C RL = 1 kΩ CL = 50 pF VDD 90% 90% 50% 10% 10% 50% VSS 1 f I/O P.G. tf = 20 ns O/I 5 VDD 2 2007-10-01 TC4066BP/BF/BFN/BFT 5. Crosstalk between Any Two Switches SWITCH ON VDD O/I I/O P.G. RL = 1 kΩ C 2.5 V VSS I/O 0V SWITCH OFF VDD −2.5 V O/I I/O RL = 1 kΩ VOUT RL = 1 kΩ C VSS 6. Crosstalk, Control to Input VDD tr = 20 ns I/O Control IN O/I C 90% VDD 90% 10% 10% VOUT RL = 10 kΩ CL = 15 pF P.G. tf = 20 ns VSS VOUT RL = 1 kΩ 7. Total Harmonic Distortion, fmax (I-O), Feedthrough VDD 2.5 V P.G. O/I I/O I/O IN 0V VOUT C CL −2.5 V RL 1 f VSS 6 2007-10-01 TC4066BP/BF/BFN/BFT Package Dimensions Weight: 0.96 g (typ.) 7 2007-10-01 TC4066BP/BF/BFN/BFT Package Dimensions Weight: 0.18 g (typ.) 8 2007-10-01 TC4066BP/BF/BFN/BFT Package Dimensions (Note) Note: This package is not available in Japan. Weight: 0.12 g (typ.) 9 2007-10-01 TC4066BP/BF/BFN/BFT Package Dimensions Weight: 0.06 g (typ.) 10 2007-10-01 TC4066BP/BF/BFN/BFT RESTRICTIONS ON PRODUCT USE 20070701-EN GENERAL • The information contained herein is subject to change without notice. • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 11 2007-10-01