Chip tantalum capacitors (Fail-safe open structure type) TCFG Series B Case Dimensions (Unit : mm) Features 1) Safety design by open function built - in. 2) Wide capacitance range 3) Screening by thermal shock. Anode mark L W1 H W2 S + Case code L W1 W2 H S B 3528-21(1411) 3.5+ −0.2 2.8+ −0.2 1.9+ −0.2 1.9+ −0.2 0.8+ −0.3 S − Product No. Explanation T C F G B 1 C 1 0 6 M 8 R 2 1 1 Series name 4 3 5 6 4 Capacitance TCFG Nominal capacitance in pF in 3 digits : 2significant figure representing the number of 0's. 2 Case code TCFG ····· B 5 Capacitance tolerance 3 Rated voltage Rated voltage (V) CODE 2.5 4 6.3 10 16 20 25 0E 0G 0J 1A 1C 1D 1E M : ±20% 6 Taping 8 : Reel width (8mm) R : Positive electrode on the side opposite to sprocket hole www.rohm.com c 2010 ROHM Co., Ltd. All rights reserved. ○ 1/7 2010.01 - Rev.G TCFG Series B Case Data Sheet Capacitance range TCFG series B Case Rated voltage (V) (μF) 2.5 0E 4 0G 6.3 0J 10 1A 16 1C 20 1D 25 1E B B B B 3.3 (335) 4.7 (475) B B B ∗ 6.8 (685) B B B ∗ B B B B ∗ 10 (106) 15 (156) B B B B 22 (226) B B B B 33 (336) B B B B 47 (476) B B B 68 (686) B B B 100 (107) B B B 150 (157) B B B ∗ B B 220 (227) B Remark) Case size codes (B) in the above show each size products line-up. ∗ : Under development Marking The indications listed below should be given on the surface of a capacitor. Polarity : The polarity should be shown by bar. (on the anode side) Rated DC voltage : Due to the small size of A case, a voltage code is used as shown below. Nominal capacitance [B Case] note 1) 10 − (1) Visual typical example (1) voltage code (2) capacitance code 16V − (2) 10 16V note 2) voltage code and capacitance code are variable with parts number www.rohm.com c 2010 ROHM Co., Ltd. All rights reserved. ○ 2/7 2010.01 - Rev.G TCFG Series B Case Data Sheet Characteristics Item Test conditions (based on JIS C5101-1 and JIS C5101-3) Performance Operating Temperature −55 °C to +125 °C Voltage reduction when temperature exceeds +85°C Maximum operating temperature +85 °C with no voltage derating at 85°C Rated Voltage (V.DC) 2.5 4 6.3 10 16 20 25 Category Voltage (V.DC) 1.6 2.5 4 6.3 10 13 16 at 125°C Surge Voltage 3.2 5.0 8 at 85°C DC leakage current Capacitance tolerance 13 20 26 32 0.5μA or 0.01CV whichever is greater (Shown in "Standard list") As per 4.9 JIS C 5101-1 As per 4.5.1 JIS C 5101-3 Voltage : Rated voltage for 1 min Shall be satisfied allowance range. As per 4.7 JIS C 5101-1 As per 4.5.2 JIS C 5101-3 Measuring frequency : 120±12Hz Measuring voltage : 0.5Vrms, +1.5V.DC Measuring circuit : DC Equivalent series circuit ±20% Tangent of loss angle (Df, tanδ) Shall be satisfied the voltage on "Standard list" As per 4.8 JIS C 5101-1 As per 4.5.3 JIS C 5101-3 Measuring frequency : 120±12Hz Measuring voltage : 0.5Vrms, +1.5V.DC Measuring circuit : DC Equivalent series circuit Impedance Shall be satisfied the voltage on "Standard list" As per 4.10 JIS C 5101-1 As per 4.5.4 JIS C 5101-3 Measuring frequency : 100±10kHz Measuring voltage : 0.5Vrms or less Measuring circuit : DC Equivalent series circuit Resistance to Appearance There should be no significant abnormality. The indications should be clear. soldering heat TCFGB0G227M8R : Less than 150% of initial limit L.C ΔC / C tanδ TCFGB0J227M8R TCFGB1A107M8R TCFGB1E475M8R Others : Less than 150% of initial limit : Less than 150% of initial limit : Less than 150% of initial limit : Less than initial limit TCFGB0G227M8R TCFGB0J227M8R TCFGB1A107M8R TCFGB1E475M8R Others 3.3 to 33μF 47 to 150μF TCFGB0E227M8R TCFGB0G227M8R TCFGB0J227M8R TCFGB1A107M8R TCFGB1C336M8R : Within ±15% of initial value : Within ±15% of initial value : Within ±15% of initial value : Within ±10% of initial value : Within ± 5% of initial value : Less than initial limit : Less than 150% of initial limit : Less than 200% of initial limit : Less than 150% of initial limit : Less than 150% of initial limit : Less than 150% of initial limit : Less than 150% of initial limit Dip in the solder bath Solder temp : 320±5°C Fail-Safe open unit actuation Within 320°C − 20s Temperature cycle Appearance There should be no significant abnormality. L.C ΔC / C tanδ Moisture resistance TCFGB0G227M8R : Less than 150% of initial limit TCFGB0J227M8R : Less than 200% of initial limit TCFGB1A107M8R : Less than 200% of initial limit TCFGB1E475M8R : Less than 150% of initial limit : Less than initial limit Others TCFGB0E227M8R : Within ±15% of initial value TCFGB0G227M8R : Within ±15% of initial value TCFGB0J227M8R : Within ±20% of initial value TCFGB1A107M8R : Within ±20% of initial value : Within ±10% of initial value Others 3.3 to 33μF 47 to 150μF TCFGB0G227M8R TCFGB0J227M8R TCFGB1A107M8R TCFGB1C336M8R : Less than initial limit : Less than 150% of initial limit : Less than 150% of initial limit : Less than 200% of initial limit : Less than 200% of initial limit : Less than 150% of initial limit Appearance There should be no significant abnormality. The indications should be clear. L.C TCFGB0G227M8R : Less than 150% of initial limit TCFGB0J227M8R : Less than 200% of initial limit TCFGB1A107M8R : Less than 200% of initial limit TCFGB1E475M8R : Less than 150% of initial limit : Less than initial limit Others ΔC / C TCFGB0G227M8R TCFGB0J227M8R TCFGB1A107M8R Others tanδ 3.3 to 33μF 47 to 150μF TCFGB0G227M8R TCFGB0J227M8R TCFGB1A107M8R TCFGB1C336M8R www.rohm.com c 2010 ROHM Co., Ltd. All rights reserved. ○ : Within : Within : Within : Within As per 4.14 JIS C 5101-1 As per 4.6 JIS C 5101-3 Dip in the solder bath Solder temp : 260±5°C Duration : 5±0.5s Repetition :1 After the specimens, leave it at room temperature for over 24h and then measure the sample. As per 4.16 JIS C 5101-1 As per 4.10 JIS C 5101-3 Repetition : 5 cycles (1 cycle : steps 1 to 4) without discontinuation. Step Temp. Time 1 −55 + − 3°C 30 + −3min 2 3 4 Room temp. 3min. or less 125 + 30 + − 2°C −3min Room temp. 3min. or less After the specimens, leave it at room temperature for over 24h and then measure the sample. As per 4.22 JIS C 5101-1 As per 4.12 JIS C 5101-3 After leaving the sample under such atmospheric condition that the temperature and humidity are 60±2°C and 90 to 95%RH, respectively, for 500±12h level it at room temperature for over 24h and then measure the sample. ±15% of initial value ±20% of initial value ±20% of initial value ±10% of initial value : Less than initial limit : Less than 150% of initial limit : Less than 150% of initial limit : Less than 200% of initial limit : Less than 200% of initial limit : Less than 150% of initial limit 3/7 2010.01 - Rev.G TCFG Series B Case Data Sheet Item Temperature Temp. Stability ΔC / C tanδ −55°C TCFGB0G227M8R TCFGB0J227M8R TCFGB1A107M8R Others : Within : Within : Within : Within 0/-15% of initial value 0/-30% of initial value 0/-30% of initial value 0/-12% of initial value − Temp. +85°C ΔC / C TCFGB0G227M8R TCFGB0J227M8R TCFGB1A107M8R Others tanδ Shall be satisfied the value on Table5 : Within : Within : Within : Within +12/0% of initial value +15/0% of initial value +15/0% of initial value +10/0% of initial value L.C Less than 1000% of intial limit Temp. +125°C ΔC / C TCFGB0J227M8R TCFGB1A107M8R TCFGB1C336M8R Others : Within : Within : Within : Within +20/0% of initial value +20/0% of initial value +20/0% of initial value +15/0% of initial value tanδ Shall be satisfied the value on Table5 L.C Less than 1250% of initial limit Appearance There should be no significant abnormality. The indications should be clear. L.C TCFGB0G227M8R : Less than 150% of initial limit TCFGB0J227M8R : Less than 200% of initial limit TCFGB1A107M8R : Less than 200% of initial limit TCFGB1E475M8R : Less than 150% of initial limit : Less than initial limit Others ΔC / C TCFGB0E227M8R TCFGB0G227M8R TCFGB0J227M8R TCFGB1A107M8R Others tanδ 3.3 to 33μF 47 to 150μF TCFGB0G227M8R TCFGB0J227M8R TCFGB1A107M8R TCFGB1C336M8R : Within : Within : Within : Within : Within ±12% of initial value ±15% of initial value ±20% of initial value ±20% of initial value ±10% of initial value As per 4.26 JIS C 5101-1 As per 4.14 JIS C 5101-3 Apply the specified surge voltage via the serial resistance of 1kΩ every 5±0.5min. for 30±5 s. each time in the atmospheric condition of 85±2°C. Repeat this procedure 1,000 times. After the specimens, leave it at room temperature for over 24h and then measure the sample. : Less than initial limit : Less than 150% of initial limit : Less than 200% of initial limit : Less than 200% of initial limit : Less than 200% of initial limit : Less than 150% of initial limit Loading at Appearance There should be no significant abnormality. High The indications should be clear. temperature TCFGB0E227M8R : Less than 125% of initial limit L.C Terminal Strength As per 4.29 JIS C 5101-1 As per 4.13 JIS C 5101-3 Shall be satisfied the value on Table5 L.C Surge Voltage Test conditions (based on JIS C5101-1 and JIS C5101-3) Performance TCFGB0G227M8R TCFGB0J227M8R TCFGB1A107M8R TCFGB1E475M8R Others : Less than 150% of initial limit : Less than 200% of initial limit : Less than 200% of initial limit : Less than 150% of initial limit : Less than initial limit ΔC / C TCFGB0G227M8R TCFGB0J227M8R TCFGB1A107M8R Others : Within : Within : Within : Within tanδ 3.3 to 33μF 47 to 100μF TCFGB0E227M8R TCFGB0G227M8R TCFGB0J227M8R TCFGB1A107M8R TCFGB1C336M8R ±15% of initial value ±20% of initial value ±20% of initial value ±10% of initial value As per 4.23 JIS C 5101-1 As per 4.15 JIS C 5101-3 After applying the rated voltage for 2000+72/0h without discontinuation via the serial resistance of 3Ω or less at a temperature of 85±2°C, leave the sample at room temperature/humidity for 1 to 2h and measure the value. After the specimens, leave it at room temperature for over 24h and then measure the sample. : Less than initial limit : Less than 150% of initial limit : Less than 150% of initial limit : Less than 200% of initial limit : Less than 200% of initial limit : Less than 200% of initial limit : Less than 150% of initial limit Capacitance The measured value should be stable. Appearance There should be no significant abnormality. As per 4.35 JIS C 5101-1 As per 4.9 JIS C 5101-3 A force is applied to the terminal until it bends to 1mm and by a prescribed tool maintain the condition for 5s. (See the figure below.) (Unit : mm) 20 50 F (Apply force) R230 1 Thickness 1.6mm 45 Adhesiveness The terminal should not come off. 45 As per 4.34 JIS C 5101-1 As per 4.8 JIS C 5101-3 Apply force of 5N in the two directions shown in the figure below for 10±1s after mounting the terminal on a circuit board. product YAA C105 Apply force a circuit board www.rohm.com c 2010 ROHM Co., Ltd. All rights reserved. ○ 4/7 2010.01 - Rev.G TCFG Series B Case Data Sheet Item Test conditions (based on JIS C5101-1 and JIS C5101-3) Performance Dimensions Be based on "External dimensions" Measure using a caliper of JIS B 7505 Class 2 or higher grade. Resistance to solvents The indication should be clear. As per 4.32 JIS C 5101-1 As per 4.18 JIS C 5101-3 Dip in the isopropyl alcohol for 30±5s, at room temperature. Solderability 3/4 or more surface area of the solder coated terminal dipped in the soldering bath should be covered with the new solder. As per 4.15.2 JIS C 5101-1 As per 4.7 JIS C 5101-3 Dip speed = 25±2.5mm/s Pre-treatment (accelerated aging) : Leave the sample on the boiling distilled water for 1h. Solder temp. : 245±5°C Duration : 3±0.5s Solder : M705 Flux : Rosin 25%, IPA 75% Vibration Capacitance Measure value should not fluctuate during the measurement. Appearance There should be no significant abnormality. www.rohm.com c 2010 ROHM Co., Ltd. All rights reserved. ○ 5/7 As per 4.17 JIS C 5101-1 Frequency : 10 to 55 to 10Hz/min. Amplitude : 1.5mm Time : 2h each in X and Y directions Mounting : The terminal is soldered on a print circuit board. 2010.01 - Rev.G TCFG Series B Case Data Sheet Standard list, TCFG series B Cases Part No. (B : 3528) Leakage Rated Derated Surge DF 120Hz Impedance current Voltage Voltage Voltage Capacitance (%) 100kHz Case Tolerance 25°C @85°C @125°C @85°C 120Hz code (%) 1WV.60s −55°C 25°C 125°C (μF) (V) (V) (Ω) (V) (μA) 85°C TCFG B 0E 227 M8R 2.5 1.6 3.2 220 ±20 5.5 34 18 22 1.5 B TCFG B 0G 156 M8R 4 2.5 5 15 ±20 0.6 12 8 10 3.0 B TCFG B 0G 226 M8R 4 2.5 5 22 ±20 0.9 12 8 10 3.0 B TCFG B 0G 336 M8R 4 2.5 5 33 ±20 1.3 12 8 10 2.5 B TCFG B 0G 476 M8R 4 2.5 5 47 ±20 1.9 14 10 12 2.0 B TCFG B 0G 686 M8R 4 2.5 5 68 ±20 2.7 14 10 12 1.9 B TCFG B 0G 107 M8R 4 2.5 5 100 ±20 4.0 30 12 16 1.6 B TCFG B 0G 157 M8R 4 2.5 5 150 ±20 6.3 34 18 22 1.3 B TCFG B 0G 227 M8R 4 2.5 5 220 ±20 8.8 40 20 30 1.3 B TCFG B 0J 106 M8R 6.3 4 8 10 ±20 0.6 12 8 10 3.0 B TCFG B 0J 156 M8R 6.3 4 8 15 ±20 0.9 12 8 10 3.0 B TCFG B 0J 226 M8R 6.3 4 8 22 ±20 1.4 12 8 10 2.5 B TCFG B 0J 336 M8R 6.3 4 8 33 ±20 2.1 12 8 10 2.0 B TCFG B 0J 476 M8R 6.3 4 8 47 ±20 3.0 14 10 12 1.9 B TCFG B 0J 686 M8R 6.3 4 8 68 ±20 4.3 30 12 16 1.6 B TCFG B 0J 107 M8R 6.3 4 8 100 ±20 6.3 30 12 16 1.5 B TCFG B 0J 157 M8R 6.3 4 8 150 ±20 9.5 34 18 22 1.5 B TCFG B 0J 227 M8R 6.3 4 8 220 ±20 70 60 30 45 1.3 B TCFG B 1A 475 M8R 10 6.3 13 4.7 ±20 0.5 10 6 8 3.0 B TCFG B 1A 685 M8R 10 6.3 13 6.8 ±20 0.7 12 8 10 3.0 B TCFG B 1A 106 M8R 10 6.3 13 10 ±20 1.0 12 8 10 3.0 B TCFG B 1A 156 M8R 10 6.3 13 15 ±20 1.5 12 8 10 2.5 B TCFG B 1A 226 M8R 10 6.3 13 22 ±20 2.2 12 8 10 2.0 B TCFG B 1A 336 M8R 10 6.3 13 33 ±20 3.3 14 10 12 1.9 B TCFG B 1A 476 M8R 10 6.3 13 47 ±20 4.7 14 10 12 1.6 B TCFG B 1A 686 M8R 10 6.3 13 68 ±20 6.8 22 12 14 1.5 B TCFG B 1A 107 M8R 10 6.3 13 100 ±20 20 40 20 30 1.5 B TCFG B 1C 335 M8R 16 10 20 3.3 ±20 0.5 10 6 8 4.2 B TCFG B 1C 475 M8R 16 10 20 4.7 ±20 0.8 10 6 8 3.0 B TCFG B 1C 685 M8R 16 10 20 6.8 ±20 1.1 10 6 8 3.0 B TCFG B 1C 106 M8R 16 10 20 10 ±20 1.6 10 6 8 2.5 B TCFG B 1C 156 M8R 16 10 20 15 ±20 2.4 10 6 8 2.0 B TCFG B 1C 226 M8R 16 10 20 22 ±20 3.5 10 6 8 1.9 B TCFG B 1C 336 M8R 16 10 20 33 ±20 5.3 16 14 16 1.9 B TCFG B 1D 335 M8R 20 13 26 3.3 ±20 0.66 10 6 8 4.2 B TCFG B 1E 335 M8R 25 16 32 3.3 ±20 0.83 10 6 8 4.2 B TCFG B 1E 475 M8R 25 16 32 4.7 ±20 1.2 10 6 8 3.0 B www.rohm.com c 2010 ROHM Co., Ltd. All rights reserved. ○ 6/7 2010.01 - Rev.G TCFG Series B Case Data Sheet Packaging specifications Case code A±0.1 B±0.1 t1±0.05 t2±0.1 B (3528) 3.3 3.8 0.25 2.2 Taping 1.75 + − 0.1 B case φ1.5 +0.1 − 0 3.5 + − 0.05 8.0 + − 0.2 A t1 B 4.0 + − 0.1 4.0 + − 0.1 Component is loaded 2.0 + − 0.05 t2 Pull-out direction Packaging style Case code Packaging B Case Taping Packaging style Plastic taping φ180mm reel Symbol Basic ordering unit R 2,000 Reel 9.0 +1.00 Plastic reel φ 180 −1.50 φ 60 +1 0 φ13±0.2 11.4±1.0 Label sticking position EIAJ ET - 7200B www.rohm.com c 2010 ROHM Co., Ltd. All rights reserved. ○ 7/7 2010.01 - Rev.G Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2010 ROHM Co., Ltd. All rights reserved. R1010A