ROHM TCTAL0G225M8R

Chip tantalum capacitors
TCT Series AL Case
zFeatures (AL)
1) Vital for all hybrid integrated circuits
board application.
2) Wide capacitance range.
3) Screening by thermal shock.
zDimensions (Unit : mm)
Anode mark
(Unit : mm)
+
Dimensions
AL case
L
3.2 +
− 0.2
W1
1.6 +
− 0.2
W2
1.2 +
− 0.2
H
1.1 +
− 0.1
S
0.8 +
− 0.2
−
zPart No. Explanation
T C T
A L
1 A
1
2
3
4
7
6
M
8 R
5
6
4
4 Nominal capacitance
1 Series name
Nominal capacitance in pF in 3 digits:
2 significant figures followed by the figure
representing the number of 0's.
TCT
2 Case style
AL
5 Capacitance tolerance
3 Rated voltage
Rated voltage (V)
CODE
2.5 4 6.3 10 16 20 25 35
0E 0G 0J 1A 1C 1D 1E 1V
M: +
− 20%
6 Taping
8 : Tape width
R : Positive electrode on the side opposite to sprocket hole
www.rohm.com
c 2009 ROHM Co., Ltd. All rights reserved.
○
1/6
2009.01 - Rev.G
Data Sheet
TCT Series AL Case
z Rated table
Rated voltage (V)
(µF)
2.5
0E
4
0G
6.3
0J
10
1A
16
1C
20
1D
25
1E
35
1V
1.0 (105)
∗AL
2.2 (225)
AL
3.3 (335)
AL
4.7 (475)
AL
6.8 (685)
AL
10 (106)
AL
15 (156)
AL
22 (226)
AL
33 (336)
AL
47 (476)
AL
AL
68 (686)
100 (107)
AL
AL
150 (157)
AL
AL
220 (227)
330 (337)
AL
∗AL
AL
Remark) Case size codes (AL) in the above show products line-up.
∗ Under development
z Marking
The indications listed below should be given on the surface of a capacitor.
(1) Polarity
: The polarity should be shown by bar. (on the anode side)
(2) Rated DC voltage : Due to the small size of AL case, a voltage code is used as shown below.
(3) Visual typical example
(1) voltage code (2) capacitance code
Voltage
Code
Rated DC
Voltage (V)
Capacitance
Code
Nominal
Capacitance (µF)
e
2.5
A
1.0
g
4
J
2.2
j
6.3
N
3.3
A
10
S
4.7
C
16
W
6.8
D
20
a
10
E
25
e
15
V
35
j
22
n
33
s
47
[AL case]
note 1)
w
68
a
100
e
150
j
220
n
330
A
s
− −
(1) (2)
As
manufacture code
note 2) voltage code and capacitance code are variable with parts number
www.rohm.com
c 2009 ROHM Co., Ltd. All rights reserved.
○
2/6
2009.01 - Rev.G
Data Sheet
TCT Series AL Case
z Characteristics
Performance
Item
Operating Temperature
−55°C to +125°C
Maximum operating
temperature with no voltage
derating
+85°C
Test conditions (based on JIS C 5101−1 and JIS C 5101−3)
Voltage reduction when temperature exceeds +85°C
Rated voltage (VDC)
2.5 4 6.3 10 16 20 25 35
at 85°C
Category voltage (VDC)
1.6 2.5 4 6.3 10 13 16 22
at 125°C
Surge voltage (VDC)
3.2 5.0 8 13 20 26 32 44
at 85°C
DC Leakage current
Shall be satisfied the voltage on
" Standard list "
As per 4.9 JIS C 5101-1
As per 4.5.1 JIS C 5101-3
Voltage : Rated voltage for 5min
Capacitance tolerance
Shall be satisfied allowance range.
±20%
As per 4.7 JIS C 5101-1
As per 4.5.2 JIS C 5101-3
Measuring frequency : 120±12Hz
Measuring voltage : 0.5Vrms +1.5 to 2V.DC
: DC Equivalent series circuit
Measuring circuit
Tangent of loss angle
(Df, tan δ)
Shall be satisfied the voltage on
" Standard list "
As per 4.8 JIS C 5101-1
As per 4.5.3 JIS C 5101-3
Measuring frequency : 120±12Hz
Measuring voltage : 0.5Vrms +1.5 to 2V.DC
: DC Equivalent series circuit
Measuring circuit
Impedance
Shall be satisfied the voltage on
" Standard list "
As per 4.10 JIS C 5101-1
As per 4.5.4 JIS C 5101-3
Measuring frequency : 100±10kHz
Measuring voltage : 0.5Vrms or less
: DC Equivalent series circuit
Measuring circuit
There should be no significant abnormality.
The indications should be clear.
As per 4.14 JIS C 5101-1
As per 4.6 JIS C 5101-3
Dip in the solder bath
Solder temp
: 260±5°C
Duration
: 5±0.5s
Repetition
:1
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
Resistance to
Soldering heat
Temperature
cycle
Appearance
L.C.
Less than initial limit
∆C / C
Within ±20% of initial value
Df (tan δ)
Less than 200% of initial limit
Appearance
There should be no significant abnormality.
The indications should be clear.
L.C.
Less than 200% of initial limit
∆C / C
Within ±20% of initial value
Df (tan δ)
Less than 200% of initial limit
As per 4.16 JIS C 5101-1
As per 4.10 JIS C 5101-3
Repetition : 5 cycles
(1 cycle : steps 1 to 4) without discontinuation.
Temp.
Time
1
−55 +
− 3°C
30±3min.
2
Room temp.
125 +
− 2°C
3min. or less
3
4
Room temp.
3min. or less
30±3min.
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
Moisture
resistance
Appearance
There should be no significant abnormality.
The indications should be clear.
L.C.
Less than 200% of initial limit
∆C / C
Within ±20% of initial value
Df (tan δ)
Less than 200% of initial limit
www.rohm.com
c 2009 ROHM Co., Ltd. All rights reserved.
○
3/6
As per 4.22 JIS C 5101-1
As per 4.12 JIS C 5101-3
After leaving the sample under such atmospheric
condition that the temperature and humidity are
60±2°C and 90 to 95% RH, respectiveiy, for 500±12h
leave it at room
temperature for over 24h and then measure the
sample.
2009.01 - Rev.G
Data Sheet
TCT Series AL Case
Performance
Item
Temperature
Stability
Temp.
−55°C
∆C / C
Within 0/−15% of initial value
Df (tan δ)
Shall be satisfied the voltage on " Standard list "
Temp.
+85°C
∆C / C
Within +15/0% of initial value
Df (tan δ)
Shall be satisfied the voltage on " Standard list "
L.C.
5µA or 0.1CV whichever is greater
Temp.
+125°C
∆C / C
Within +20/0% of initial value
Df (tan δ)
Shall be satisfied the voltage on " Standard list "
L.C.
6.3µA or 0.125CV whichever is greater
Appearance
There should be no significant abnormality.
L.C.
Less than 200% of initial value
∆C / C
Within ±20% of initial value
Df (tan δ)
Less than 200% of initial limit
Loading at
Appearance
High temperature
L.C.
Terminal
strength
As per 4.29 JIS C 5101-1
As per 4.13 JIS C 5101-3
−
L.C.
Surge voltage
Test conditions (based on JIS C 5101−1 and JIS C 5101− 3)
There should be no significant abnormality.
Less than 200% of initial limit
∆C / C
Within ±20% of initial value
Df (tan δ)
Less than 200% of initial limit
Capacitance
The measured value should be stable.
Appearance
There should be no significant abnormality.
As per 4.26JIS C 5101-1
As per 4.14JIS C 5101-3
Apply the specified surge voltage every 5±0.5 min.
for 30±5 s. each time in the atmospheric condition of 85±2°C.
Repeat this procedure 1,000 times.
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
As per 4.23 JIS C 5101-1
As per 4.15 JIS C 5101-3
After applying the rated voltage for 2000+72/0 h without
discontinuation via the serial resistance of 3Ω or less
at a temperature of 85±2°C, leave the sample at room
temperature / humidity for over 24h and measure the value.
As per 4.35 JIS C 5101-1
As per 4.9 JIS C 5101-3
A force is applied to the terminal until it bends to 1mm and
by a prescribed tool maintain the condition for 5s.
(See the figure below)
(Unit : mm)
50
20
F (Apply force)
R230
1
thickness=1.6mm
45
www.rohm.com
c 2009 ROHM Co., Ltd. All rights reserved.
○
4/6
45
2009.01 - Rev.G
Data Sheet
TCT Series AL Case
Performance
Item
Adhesiveness
Test conditions (JIS C 5101−1 and JIS C 5101− 3)
As per 4.34 JIS C 5101-1
As per 4.8 JIS C 5101-3
Apply force of 5N in the two directions shown in the figure
below for 10±1s after mounting the terminal on a circuit board.
The terminal should not come off.
product
ja
Apply force
a circuit board
Dimensions
Refer to "External dimensions"
Measure using a caliper of JIS B 7507 Class 2
or higher grade.
Resistance to solvents
The indication should be clear
As per 4.32 JIS C 5101-1
As per 4.18 JIS C 5101-3
Dip in the isopropyl alcohol for 30±5s, at room
temperature.
Solderability
3/4 or more surface area of the solder coated
terminal dipped in the soldering bath should
be covered with the new solder.
As per 4.15.2 JIS C 5101-1
As per 4.7 JIS C 5101-3
Dip speed=25±2.5mm / s
Pre-treatment (accelerated aging): Leave
the sample on the boiling distilled water for 1 h.
Solder temp. : 245±5°C
Duration
: 3±0.5s
Solder
: M705
Flux
: Rosin 25% IPA 75%
Vibration
Capacitance Measure value should not fluctuate during the
measurement.
Appearance There should be no significant abnormality.
As per 4.17 JIS C 5101-1
Frequency : 10 to 55 to 10Hz/min.
Amplitude : 1.5mm
Time : 2h each in X and Y directions
Mounting : The terminal is soldered on a print circuit board.
z Standard products list, TCT series
Df
Impedance
Leakage
120Hz
100kHz
Tolerance current
(%)
25°C
1WV.5min
(%)
25°C
125°C
−55°C
(Ω)
(µA)
85°C
Rated
voltage
85°C
Category
voltage
125°C
Surge
voltage
85°C
(V)
(V)
(V)
TCT AL 0E 227
2.5
1.6
3.3
220
+
− 20
5.5
35
20
25
2.5
∗TCT AL 0E 337
2.5
1.6
3.3
330
+
− 20
16.5
80
30
40
2.5
4.0
35
20
25
3.0
6.0
35
20
25
2.7
Part No.
Cap.
120Hz
(µF)
TCT AL 0G 107
4
2.5
5.2
100
TCT AL 0G 157
4
2.5
5.2
150
+
− 20
+
− 20
TCT AL 0G 227
4
2.5
5.2
220
+
− 20
20
35
20
25
2.5
TCT AL 0J 686
6.3
4
8.0
68
+
− 20
4.3
35
20
25
4.0
TCT AL 0J 107
6.3
4
8.0
100
+
− 20
6.3
34
18
24
3.0
TCT AL 1A 336
10
6.3
13
33
+
− 20
3.3
30
15
20
4.0
TCT AL 1A 476
10
6.3
13
47
+
− 20
4.7
35
20
25
4.0
TCT AL 1C 156
16
10
20
15
+
− 20
2.4
30
15
20
4.0
TCT AL 1C 226
16
10
20
22
+
− 20
3.6
35
20
25
4.0
TCT AL 1D 106
20
13
26
10
+
− 20
2.0
30
15
20
8.0
TCT AL 1E 475
25
16
32
4.7
+
− 20
1.2
30
15
20
8.0
TCT AL 1E 685
25
16
32
6.8
1.7
30
15
20
8.0
TCT AL 1V 225
35
22
45
2.2
+
− 20
+
− 20
0.8
30
15
20
8.0
TCT AL 1V 335
35
22
45
3.3
+
− 20
1.2
30
15
20
8.0
=Tolerance (M : ±20%)
∗ : Under development
www.rohm.com
c 2009 ROHM Co., Ltd. All rights reserved.
○
5/6
2009.01 - Rev.G
Data Sheet
TCT Series AL Case
z Packaging specifications
Case code
A±0.1
B±0.1
t1±0.05
t2±0.1
AL
1.9
3.5
0.25
1.3
+0.1
−0
3.5±0.05
A
B
t1
8.0±0.2
φ1.5
1.75±0.1
Taping [AL case]
Chip
4.0±0.1
4.0±0.1
t2
2.0±0.05
Feeding direction
z Packaging style
Case code
Packaging
AL case
Taping
Packaging style
plastic taping
Symbol Basic ordering units
φ180mm Reel
R
3,000pcs
φ60 +1
0
0
φ180−1.5
11.4+
−1.0
φ13+
−0.2
+1.0
9.0 0
Reel [AL case]
Pull direction
Label sticking position
www.rohm.com
c 2009 ROHM Co., Ltd. All rights reserved.
○
EIAJ ET−7200B
6/6
2009.01 - Rev.G
Appendix
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM
CO.,LTD.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you
wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM
upon request.
Examples of application circuits, circuit constants and any other information contained herein illustrate the
standard usage and operations of the Products. The peripheral conditions must be taken into account
when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document. However, should
you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and examples
of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to
use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information.
The Products specified in this document are intended to be used with general-use electronic equipment
or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices).
The Products are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or
malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard against the
possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as
derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your
use of any Product outside of the prescribed scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or system
which requires an extremely high level of reliability the failure or malfunction of which may result in a direct
threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment,
aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear
no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may be controlled under
the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact your nearest sales office.
ROHM Customer Support System
www.rohm.com
Copyright © 2009 ROHM Co.,Ltd.
THE AMERICAS / EUROPE / ASIA / JAPAN
Contact us : webmaster @ rohm.co. jp
21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan
TEL : +81-75-311-2121
FAX : +81-75-315-0172
Appendix-Rev4.0