Conductive polymer chip tantalum capacitors ( Bottom surface electrode type ) TCTO Series AL Case Features (AL) 1) Conductive polymer used for the cathode material. 2) Ultra low ESR 3) Small package, but big capacitance 4) Screening by thermal shock Dimensions (Unit : mm) Anode mark (Unit : mm) H W1 L W2 S S 6 M 8 R 5 6 Dimensions AL case L 3.2 + − 0.2 W1 1.6 + − 0.2 W2 1.2 + − 0.2 H 1.1 + − 0.1 S 0.8 + − 0.2 Part No. Explanation T C T O 1 A L 2 0 J 4 3 7 4 4 Nominal capacitance 1 Series name Nominal capacitance in pF in 3 digits: 2 significant figures followed by the figure representing the number of 0's. TCTO 2 Case style AL 5 Capacitance tolerance 3 Rated voltage Rated voltage (V) CODE 2.5 4 6.3 10 0E 0G 0J 1A M: + − 20% 6 Taping 8 : Tape width R : Positive electrode on the side opposite to sprocket hole This specification has possibility of charge, due to underdevelopment product. Please ask for latest specification to our sales. www.rohm.com c 2011 ROHM Co., Ltd. All rights reserved. ○ 1/5 2011.06 - Rev.D TCTO Series AL Case Data Sheet Rated table Rated voltage (V) (μF) 2.5 0E 4 0G 6.3 0J 10 1A 22 (226) AL 33 (336) AL 47 (476) AL 68 (686) ∗ AL AL 100 (107) AL 150 (157) ∗ AL AL 220 (227) Remark) Case size codes (AL) in the above show products line-up. ∗Under development Marking The indications listed below should be given on the surface of a capacitor. (1) Polarity : The polarity should be shown by bar. (on the anode side) (2) Rated DC voltage : Due to the small size of AL case, a voltage code is used as shown below. (3) Visual typical example (1) voltage code (2) capacitance code Voltage Code Rated DC Voltage (V) Capacitance Code Nominal Capacitance (μF) e 2.5 A 1.0 g 4 E 1.5 j 6.3 J 2.2 A 10 N 3.3 S 4.7 W 6.8 a 10 e j 15 22 [AL case] note 1) n 33 s 47 w 68 a 100 e 150 j s − − (1) (2) js manufacture code note 2) voltage code and capacitance code are variable with parts number www.rohm.com c 2011 ROHM Co., Ltd. All rights reserved. ○ 2/5 2011.06 - Rev.D TCTO Series AL Case Data Sheet Characteristics Performance Item Operating Temperature −55°C to +105°C Maximum operating temperature with no voltage derating +85°C Rated voltage (VDC) Category voltage (VDC) Surge voltage (VDC) 2.5 4 6.3 10 2 3.2 5 3.2 5 8 8 13 Test conditions (based on JIS C 5101−1 and JIS C 5101−3) Voltage reduction when temperature exceeds +85°C at 85°C at 105°C at 85°C DC Leakage current Shall be satisfied the voltage on " Standard list " As per 4.9 JIS C 5101-1 As per 4.5.1 JIS C 5101-3 Voltage : Rated voltage for 5min Capacitance tolerance Shall be satisfied allowance range. ±20% As per 4.7 JIS C 5101-1 As per 4.5.2 JIS C 5101-3 Measuring frequency : 120±12Hz Measuring voltage : 0.5Vrms +1.5 to 2V.DC : DC Equivalent series circuit Measuring circuit Tangent of loss angle (Df, tan δ) Shall be satisfied the voltage on " Standard list " As per 4.8 JIS C 5101-1 As per 4.5.3 JIS C 5101-3 Measuring frequency : 120±12Hz Measuring voltage : 0.5Vrms +1.5 to 2V.DC : DC Equivalent series circuit Measuring circuit ESR Shall be satisfied the voltage on " Standard list " As per 4.10 JIS C 5101-1 As per 4.5.4 JIS C 5101-3 Measuring frequency : 100±10kHz Measuring voltage : 0.5Vrms or less : DC Equivalent series circuit Measuring circuit There should be no significant abnormality. The indications should be clear. As per 4.14 JIS C 5101-1 As per 4.6 JIS C 5101-3 Dip in the solder bath Solder temp : 240±5°C Duration : 10±0.5s Repetition :1 After the specimens, leave it at room temperature for over 24h and then measure the sample. Resistance to Soldering heat Temperature cycle Moisture resistance Appearance L.C. Less than 300% of initial limit ΔC / C Within ±20% of initial value Df (tan δ) Less than 300% of initial limit Appearance There should be no significant abnormality. The indications should be clear. L.C. Less than 1000% of initial limit ΔC / C Within ±20% of initial value Df (tan δ) Less than 300% of initial limit Appearance There should be no significant abnormality. The indications should be clear. L.C. Less than 300% of initial limit ΔC / C Within +30/−20% of initial value Df (tan δ) Less than 300% of initial limit www.rohm.com c 2011 ROHM Co., Ltd. All rights reserved. ○ As per 4.16 JIS C 5101-1 As per 4.10 JIS C 5101-3 Repetition : 5 cycles (1 cycle : steps 1 to 4) without discontinuation. Temp. Time 1 −55±3°C 30±3min. 2 Room temp. 3min. or less 3 105±2°C 30±3min. 4 Room temp. 3min. or less As per 4.22 JIS C 5101-1 As per 4.12 JIS C 5101-3 After leaving the sample under such atmospheric condition that the temperature and humidity are 40±2°C and 90 to 95% RH, respectiveiy, for 500±12h leave it at room temperature for 24h and then measure the sample. 3/5 2011.06 - Rev.D TCTO Series AL Case Performance Item Temperature Stability Data Sheet Temp. −55°C ΔC / C Within 0/−20% of initial value Df (tan δ) Shall be satisfied the voltage on " Standard list " Temp. +105°C ΔC / C Within +50/0% of initial value Df (tan δ) Shall be satisfied the voltage on " Standard list " L.C. Less than 1.0CV Appearance There should be no significant abnormality. L.C. Less than 200% of initial value ΔC / C Within ±20% of initial value Df (tan δ) Less than 200% of initial limit Loading at Appearance High temperature L.C. Terminal strength As per 4.29 JIS C 5101-1 As per 4.13 JIS C 5101-3 − L.C. Surge voltage Test conditions (based on JIS C 5101−1 and JIS C 5101− 3) There should be no significant abnormality. Less than 400% of initial limit ΔC / C Within ±20% of initial value Df (tan δ) Less than 300% of initial limit Capacitance The measured value should be stable. Appearance There should be no significant abnormality. As per 4.26JIS C 5101-1 As per 4.14JIS C 5101-3 Apply the specified surge voltage every 5±0.5 min. for 30±5 s. each time in the atmospheric condition of 85±2°C. Repeat this procedure 1,000 times. After the specimens, leave it at room temperature for over 24h and then measure the sample. As per 4.23 JIS C 5101-1 As per 4.15 JIS C 5101-3 After applying the rated voltage for 1000+36/0 h without discontinuation via the serial resistance of 3Ω or less at a temperature of 85±2°C, leave the sample at room temperature / humidity for 24h and measure the value. As per 4.35 JIS C 5101-1 As per 4.9 JIS C 5101-3 A force is applied to the terminal until it bends to 1mm and by a prescribed tool maintain the condition for 5s. (See the figure below) (Unit : mm) 20 50 F (Apply force) R230 1 thickness=1.6mm 45 Adhesiveness 45 As per 4.34 JIS C 5101-1 As per 4.8 JIS C 5101-3 Apply force of 5N in the two directions shown in the figure below for 10±1s after mounting the terminal on a circuit board. The terminal should not come off. product ja Apply force a circuit board Dimensions Refer to "External dimensions" Measure using a caliper of JIS B 7507 Class 2 or higher grade. Resistance to solvents The indication should be clear As per 4.32 JIS C 5101-1 As per 4.18 JIS C 5101-3 Dip in the isopropyl alcohol for 30±5s, at room temperature. Solderability 3/4 or more surface area of the solder coated As per 4.15.2 JIS C 5101-1 As per 4.7 JIS C 5101-3 terminal dipped in the soldering bath should be covered with the new solder. Dip speed=25±2.5mm / s Pre-treatment (accelerated aging): Leave the sample on the boiling distilled water for 1 h. Solder temp. : 245±5°C Duration : 3±0.5s Solder : M705 Flux : Rosin 25% IPA 75% Vibration Capacitance Measure value should not fluctuate during the measurement. Appearance There should be no significant abnormality. www.rohm.com c 2011 ROHM Co., Ltd. All rights reserved. ○ 4/5 As per 4.17 JIS C 5101-1 Frequency : 10 to 55 to 10Hz/min. Amplitude : 1.5mm Time : 2h each in X and Y directions Mounting : The terminal is soldered on a print circuit board. 2011.06 - Rev.D TCTO Series AL Case Data Sheet Df ESR Leakage 120Hz 100kHz Tolerance current (%) 25°C 1WV.5min 25°C 105°C (mΩ) −55°C (μA) (%) 85°C Rated voltage 85°C Category voltage 105°C Surge voltage 85°C Cap. 120Hz (V) (V) (V) (μF) TCTO AL 0E 107 2.5 2 3.2 100 ± 20 25.0 10 10 15 200 ∗TCTO AL 0E 157 2.5 2 3.2 150 ± 20 37.5 10 10 15 200 Part No. TCTO AL 0G 686 4 3.2 5 68 ± 20 27.2 10 10 15 200 TCTO AL 0G 107 4 3.2 5 100 ± 20 40.0 10 10 15 200 TCTO AL 0J 476 6.3 5 8 47 ± 20 29.7 10 10 15 200 ∗TCTO AL 0J 686 6.3 5 8 68 ± 20 42.9 10 10 15 200 TCTO AL 1A 226 10 8 13 22 ± 20 22.0 6 6 9 200 TCTO AL 1A 336 10 8 13 33 ± 20 33.0 10 10 15 200 =Tolerance(M : ± 20%) ∗ =Under development Case code A±0.1 B±0.1 t1±0.05 t2±0.1 AL 1.9 3.5 0.25 1.3 3.5±0.05 +0.1 −0 B t1 8.0±0.2 φ1.5 1.75±0.1 Taping [AL case] Chip A 4.0±0.1 Positiv Electrode(+) 4.0±0.1 2.0±0.05 t2 Feeding direction Case code Packaging AL case Taping Packaging style Symbol Basic ordering units φ180mm Reel plastic taping R 3,000pcs +1.0 9.0 0 Reel [AL case] −1.5 φ180 0 φ60 +1 0 φ13+ −0.2 11.4+ −1.0 Pull direction Label sticking position EIAJ ET−7200A www.rohm.com c 2011 ROHM Co., Ltd. All rights reserved. ○ 5/5 2011.06 - Rev.D Notice Notes Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. R1120A