TRACOPOWER THI0513

DC/DC Converter
THI Series
2 Watt
Features
I/O-Isolation Test Voltage 6000V
Supplementary Insulation to meet IEC/EN
60950 and IEC/EN 60601-1 Safety Standards
Agency Safety Approvals
SMD-Technology with Ceramic Capacitors
Regulated Single– and Dual Output Models
Low Coupling Capacity
24–Pin DIP Plastic Package
2 Year Product Warranty
The THI series is a family of dc/dc-converter with very high I/OIsolation specification. They are certified according to EN 60950
and IEC-60601-1 safety standards and offer a cost effective solution for all industrial, telecom and medical applications where
a supplementary insulation is required. SMD-technology and a
100 % production test of the safety barrier ensure a very high
reliability of this product.
Models
Ordercode
THI 0511
THI 0512
THI 0513
THI 0520
THI 0521
THI 0522
THI
THI
THI
THI
THI
THI
1211
1212
1213
1220
1221
1222
THI
THI
THI
THI
THI
THI
2411
2412
2413
2420
2421
2422
www.tracopower.com
Input voltage
Output voltage
Output current max.
Efficiency typ.
5 VDC ± 10%
5 VDC
12 VDC
15 VDC
± 5 VDC
±12 VDC
±15 VDC
400 mA
165 mA
130 mA
±100 mA
± 80 mA
± 65 mA
62
63
64
42
57
57
%
%
%
%
%
%
12 VDC ± 10%
5 VDC
12 VDC
15 VDC
± 5 VDC
±12 VDC
±15 VDC
400 mA
165 mA
130 mA
±100 mA
± 80 mA
± 65 mA
62
63
64
45
59
59
%
%
%
%
%
%
24 VDC ± 10%
5 VDC
12 VDC
15 VDC
± 5 VDC
±12 VDC
±15 VDC
400 mA
165 mA
130 mA
±100 mA
± 80 mA
± 65 mA
62
63
64
45
58
58
%
%
%
%
%
%
Page 1
DC/DC Converter
THI Series
2 Watt
Input Specifications
Input current no load
5 Vin models:
12 Vin models:
24 Vin models:
100 mA typ.
50 mA typ.
30 mA typ.
Input current no load
5 Vin models:
12 Vin models:
24 Vin models:
660 mA typ.
280 mA typ.
140 mA typ.
Surge voltage (1 sec. max.)
5 Vin models:
12 Vin models:
24 Vin models:
7.5 V max.
15 V max.
30 V max.
Input filter
Pi-Filter
Output Specifications
Voltage set accuracy
±3%
Voltage balance (dual output models)
± 3 % max.
Regulation
± 0.5 % max.
± 1.0 % max.
– Input variation Vin min. to Vin max.
– Load variation 10 – 100 %:
Ripple and noise (20 MHz Bandwidth)
50 mVpk-pk max.
Temperature coefficient
± 0.02 % / °C
Current limitation
> 120 % constant current
Short circuit protection
indefinite (automatic recovery)
Capacitive load
– Single output models
– Dual output models
680 µF max.
270 µF max.
Isolation voltage
– Rated isolation voltage
– Isolation test voltage (1 sec.)
3’000 Vrms (for 250VAC working voltage)
6‘000 VDC
Isolation capacity
Input/Output
20 pF typ.
Isolation resistance
Input/Output
>10‘000 M ohm
Isolation /Safety
Safety standards
EN 60950
IEC/EN 60601-1 rated for 250VAC
Safety approvals
test report by BSI (British Standard Institute)
General Specifications
Temperature ranges
– Operating
– Case
– Storage
– 25 °C ... +60 °C
+ 95 °C
– 40 °C ... +125 °C
Derating above 60°C
3%
Humidity (non condensing)
95 % rel H max.
Reliability, calculated MTBF (MIL-HDBK-217 E)
> 600’000 h @ 25 °C
Switching frequency
25 – 80 kHz (depending on load)
All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated.
www.tracopower.com
Page 2
DC/DC Converter
THI Series
2 Watt
Physical Specifications
Case material
non conductive black plastic
(flammability to UL 94V-0)
Weight
12 g (0.42 oz)
Soldering temperature
max. 260°C / 10 sec
2.54 (0.1)
2.0 ±0.5
(0.08 ±0.02)
Outline Dimensions mm (inches)
1
2
Bottom view
20.32 (0.8)
15
(0.1)
2.54
27.94 (1.1)
32 ±0.5 (1.25 ±0.02)
24
23
2.54 (0.1)
13
2.4 ±0.5
10
11
12
15.24 (0.6)
(0.1 ±0.02)
4
10 ±0.5
20 ±0.5 (0.8 ±0.02)
Pin-Out
Pin
Single
Dual
1
+Vin (Vcc)
+Vin (Vcc)
2
+Vin (Vcc)
+Vin (Vcc)
10
No pin
Common
11
No pin
Common
12
–Vout
No pin
13
+Vout
–Vout
15
No pin
+Vout
23
–Vin (GND)
–Vin (GND)
24
–Vin (GND)
–Vin (GND)
(0.16) (0.4 ±0.02)
( ) = inches
Pins ø 0.5 mm (0.02)
Specifications can be changed without notice
Rev. 05/01
Jenatschstrasse 1 • CH-8002 Zurich • Switzerland
Tel. +41-1284 2911 • Fax +41-1201 1168 • e-mail: [email protected] • internet: http://www.tracopower.com
Page 3