TL062 TL062A - TL062B LOW POWER J-FET DUAL OPERATIONAL AMPLIFIERS ■ ■ ■ ■ ■ ■ ■ ■ VERY LOW POWER CONSUMPTION : 200µA WIDE COMMON-MODE (UP TO VCC+) AND DIFFERENTIAL VOLTAGE RANGES LOW INPUT BIAS AND OFFSET CURRENTS OUTPUT SHORT-CIRCUIT PROTECTION HIGH INPUT IMPEDANCE J-FET INPUT STAGE INTERNAL FREQUENCY COMPENSATION LATCH UP FREE OPERATION HIGH SLEW RATE : 3.5V/µs N DIP8 (Plastic Package) D SO8 (Plastic Micropackage) DESCRIPTION ORDER CODES The TL062, TL062A and TL062B are high speed J-FET input dual operational amplifier family. Each of these J-FET input operational amplifiers incorporates well matched, high voltage J-FET and bipolar transistors in a monolithic integrated circuit. The devices feature high slew rates, low input bias and offsetcurrents, andlow offset voltage temperature coefficient. Part Number Temperature Range o o Package N D TL062M/AM/BM -55 C, +125 C ● ● TL062I/AI/BI -40oC, +105oC ● ● ● ● TL062C/AC/BC o o 0 C, +70 C Example : TL062IN PIN CONNECTIONS (top view) 1 2 - 3 + 4 October 1997 8 7 - 6 + 5 1 - Output 1 2 - Inverting input 1 3 - Non-inverting input 1 4 - VCC 5 - Non-inverting input 2 6 - Inverting input 2 7 - Output 2 8 - VCC+ 1/10 TL062 - TL062A - TL062B SCHEMATIC DIAGRAM VC C 220 Ω Inverting Input Non-inverting Input 64 Ω 45k Ω 270 Ω 4.2k Ω 1/2 TL062 Output 3.2k Ω 100 Ω V CC MAXIMUM RATINGS Symbol Parameter TL062M,AM,BM TL062I,AI,BI TL062C,AC,BC Unit Supply Voltage - (note 1) ±18 ±18 ±18 V Vi Input Voltage - (note 3) ±15 ±15 ±15 V Vid Differential Input Voltage - (note 2) ±30 ±30 ±30 V Ptot Power Dissipation 680 680 680 mW Infinite Infinite Infinite VCC Output Short-Circuit Duration (Note 4) Toper Operating Free-Air Temperature Range -55 to +125 -40 to +105 0 to +70 o C Tstg Storage Temperature Range - 65 to + 150 - 65 to + 150 - 65 to + 150 o C Notes : 2/10 1. All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the zero reference level is the midpoint between VCC+ and VCC-. 2. Differential voltages are at the non-inverting input terminal with respect to the inverting input terminal. 3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less. 4. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded. TL062 - TL062A - TL062B ELECTRICAL CHARACTERISTICS VCC = ± 15V, Tamb = 25oC (unless otherwise specified) Symbol Vio DVio Iio Iib TL062M Parameter Min. SVR Icc VO1/VO2 PD Typ. Max. Unit 10 Input Offset Current * o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. 5 100 20 5 100 10 5 200 5 pA nA Input Bias Current * Tamb = 25oC Tmin. ≤ Tamb ≤ Tmax. 30 200 50 30 200 20 30 400 10 pA nA Output Voltage Swing (RL = 10kΩ) o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. CMR Typ. Max. Min. Temperature Coefficient of Input Offset Voltage (Rs = 50Ω) VOPP Ri Min. 3 Input Common Mode Voltage Range GBP Typ. Max. TL062C Input Offset Voltage (Rs = 50Ω) o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. Vicm Avd TL062I Large Signal Voltage Gain (RL = 10kΩ, Vo = ± 10V) o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. mV 6 15 3 6 9 3 10 15 20 µV/oC 10 ±11.5 +15 -12 ±11.5 +15 -12 ±11 +15 -12 20 20 27 20 20 27 20 20 27 V V V/mV 4 4 6 Gain Bandwidth Product o (Tamb = 25 C, RL = 10kΩ CL = 100pF) 4 4 6 3 3 6 MHz 1 Input Resistance 10 1 12 10 1 12 Ω 1012 dB Common Mode Rejection Ratio (Rs = 50Ω) 80 86 80 86 70 76 Supply Voltage Rejection Ratio (Rs = 50Ω) 80 95 80 95 70 95 dB Supply Current (Per Amplifier) o (Tamb = 25 C, no load, no signal) 200 Channel Separation (Av = 100, Tamb = 25oC) 120 250 200 250 200 250 µA dB Total Power Consumption (Each Amplifier) (Tamb = 25oC, no load, no signal) 120 120 mW 6 7.5 6 7.5 6 7.5 * Input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive. Pulse techniques must be used that will maintain the junction temperature as closes to the ambient temperature as possible. ELECTRICAL CHARACTERISTICS (continued) VCC = ± 15V, Tamb = 25oC Symbol SR tr KOV en Parameter TL062C,I,M Typ. 1.5 3.5 V/µs Rise Time (Vi = 20mV, RL = 10kΩ, CL = 100pF, AV = 1) 0.2 µs Overshoot Factor (Vi = 20mV, RL = 10kΩ, CL = 100pF, AV = 1) (see figure 1) 10 Equivalent Input Noise Voltage (Rs = 100Ω, f = 1KHz) 42 Slew Rate (Vi = 10V, RL = 10kΩ, CL = 100pF, AV = 1) Max. Unit Min. % nV √ Hz 3/10 TL062 - TL062A - TL062B ELECTRICAL CHARACTERISTICS (continued) VCC = ± 15V, Tamb = 25oC (unless otherwise specified) Symbol Vio DVio Iio Iib Min. Typ. Max. Unit Temperature Coefficient of Input Offset Voltage (Rs = 50Ω) 10 Input Offset Current * o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. 5 100 3 5 100 3 pA nA Input Bias Current * Tamb = 25oC Tmin. ≤ Tamb ≤ Tmax. 30 200 7 30 200 7 pA nA mV 6 7.5 2 3 5 µV/oC 10 ±11.5 +15 -12 ±11.5 +15 -12 Output Voltage Swing (RL = 10kΩ) o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. 20 20 27 20 20 27 Large Signal Voltage Gain (RL = 10kΩ, Vo = ± 10V) o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. 4 4 6 4 4 6 VOPP Ri Typ. Max. 3 Input Common Mode Voltage Range GBP Min. TL062BC,BI,BM Input Offset Voltage (Rs = 50Ω) o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. Vicm Avd TL062AC,AI, AM Parameter V V V/mV Gain Bandwidth Product o (Tamb = 25 C, RL = 10kΩ, CL = 100pF) MHz 1 Input Resistance 10 1 12 10 12 Ω CMR Common Mode Rejection Ratio (R s = 50Ω) 80 86 80 86 dB SVR Supply Voltage Rejection Ratio (Rs = 50Ω) 80 95 80 95 dB Icc VO1/VO2 PD SR µA Supply Current (Per Amplifier) o (Tamb = 25 C, no load, no signal) 200 o Channel Separation (Av = 100, Tamb = 25 C) 200 120 250 120 mW Total Power Consumption (Each Amplifier) o (Tamb = 25 C, no load, no signal) Slew Rate (Vi = 10V, RL = 10kΩ, CL = 100pF, AV = 1) 250 6 3.5 6 1.5 7.5 3.5 V/µs tr Rise Time (Vi = 20mV, RL = 10kΩ, CL = 100pF, AV = 1) 0.2 0.2 µs KOV Overshoot Factor (Vi = 20mV, RL = 10kΩ, CL = 100pF, AV = 1) - (see figure 1) 10 10 Equivalent Input Noise Voltage (Rs = 100Ω, f = 1KHz) 42 42 en 1.5 7.5 % * The input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive. Pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature as possible. 4/10 nV √ Hz TL062 - TL062A - TL062B MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS SUPPLY VOLTAGE MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS FREE AIR TEMP. R L = 1 0 kΩ 25 T a m b= +25°C See fig ure 2 20 15 10 5 0 2 4 6 8 10 12 14 16 SUPPLY VOLTAGE (V) 30 MAXIMUM PEAK-TO-PEAKOUTPUT VOLTAGE (V) MAXIMUM PEAK-TO-PEAKOUTPUT VOLTAGE (V) 30 MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS LOAD RESISTANCE 25 20 15 10 5 15V See Figure 2 -7 5 -5 0 - 25 0 25 50 75 125 MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS FREQUENCY 20 15 10 VCC = 15V Ta m b = +2 5°C Se e Fig ure 2 5 0 100 200 700 1k 2k 400 4k 7k 10k MAXIMUM PEAK-TO-PEAKOUTPUT VOLTAGE (V) 30 25 25 V CC = 15V V CC = 12V V CC = 5V V CC = 2V R L =10kΩ T a m b = + 25°C S ee Figu re 2 20 15 10 5 0 1k 10K 100K 1M 10M FREQUENCY (Hz) DIFFERENTIAL VOLTAGE AMPLIFICATION VERSUS FREE AIR TEMPERATURE LARGE SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE SHIFT VERSUS FREQUENCY 6 7 105 4 2 V CC = 15V -50 -25 R L = 10 kΩ AMPLIFICATION (V/V) 10 DIFFERENTIAL VOLTAGE 10 VCC = 5V to 15V RL = 2kΩ Tamb = +25°C 4 10 3 10 102 101 0 25 50 75 FREE AIR TEMPERATURE (°C) 100 125 1 0 DIFFER ENTIAL VOLTAGE AMPLIFICATION (left scale) PHASE SHIFT (right scale) 10 100 45 90 135 1 -75 -50 F R EE A I R T EM P E R AT U R E ( ° C ) L OAD RE SIS TA N CE (k Ω ) DIFFERENTIAL VOLTAGE AMPLIFICATION (V/mV) Ω = 10k L 0 30 MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE (V) VC C = R 1k 10k 100k 1M 180 10M FREQUENCY (Hz) 5/10 TL062 - TL062A - TL062B SUPPLY CURRENT PER AMPLIFIER VERSUS SUPPLY VOLTAGE SUPPLY CURRENT PER AMPLIFIER VERSUS FREE AIR TEMPERATURE 250 SUPPLY CURRENT (µA) SUPPLY CURRENT (µA) 250 200 150 100 T amb = +25°C No signal 50 200 150 100 VCC = 15V 50 No signal No load No load 0 0 0 2 4 10 12 6 8 SUPPLY VOLTAGE ( V) 14 -75 16 TOTAL POWER DISSIPATED VERSUS FREE AIR TEMPERATURE COMMON MODE REJECTION RATIO VERSUS FREE AIR TEMPERATURE 30 87 V C C = 15V No signa l No load 25 20 15 10 5 0 -75 -50 -25 0 25 50 75 100 125 COMMON MODE REJECTION RATIO (dB) TOTAL POWER DISSIPATED (mW) -25 0 25 50 75 100 125 FREE AIR TEMPERATURE (°C) -50 86 85 84 83 VC C = 82 R 81 -75 -50 -25 0 25 L 50 1 5V = 1 0kΩ 75 100 125 FREE AIR TEMPERATURE (°C) FREE AIR TEMPERATURE (°C) NORMALIZED UNITY GAIN BANDWIDTH SLEW RATE, AND PHASE SHIFT VERSUS TEMPERATURE INPUT BIAS CURRENT VERSUS FREE AIR TEMPERATURE 1.1 S LEW RAT E (left scale) 1 0.9 0.8 0.7 -75 R L = 10kΩ f = B1for phase shift -25 1.01 1 0.99 VCC = 15V -50 1.02 0 0.98 25 50 0.97 75 100 125 FREE AIR TEMPERATURE (°C) INPUT BIAS CURRENT (nA) 1.2 PHASE SHIFT (right scale) UNITY -GAIN-BANDWIDTH (left scale) 1.03 NORMALIZED PHASESHIFT NORMALIZED UNITY-GAIN BANDWIDTH AND SLEW RATE 100 1.3 VCC = 15V 10 1 0.1 0.01 -50 -25 0 25 50 75 100 FREE AIR TEMPERATURE (°C) 6/10 125 TL062 - TL062A - TL062B OUTPUT VOLTAGE VERSUS ELAPSED TIME 6 28 2 OUTPUT VOLTAGE (mV) INPUT 4 OUTPUT 0 VCC = 15V R L = 10kΩ -2 CL = 100pF Tamb = +25°C -4 24 OVERSHOOT 20 90% 16 12 8 V 4 10% tr 0 -6 2 4 6 TIME (µs) 8 0.2 = 15V 0.4 0.6 0.8 1 12 14 TIME (µs) 10 EQUIVALENT INPUT NOISE VOLTAGE VERSUS FREQUENCY 100 VOLTAGE (nV/VHz) 0 CC R L = 10kΩ Tamb = +25°C 0 -4 EQUIVALENT INPUT NOISE (V) INPUT AND OUTPUT VOLTAGES VOLTAGE FOLLOWER LARGE SIGNAL PULSE RESPONSE 90 80 70 60 50 40 30 VCC = 15V R S = 100 Ω Tamb = +25°C 20 10 0 40 10 100 400 1k 4k 10k 40k 100k FREQUENCY (Hz) 7/10 TL062 - TL062A - TL062B PARAMETER MEASUREMENT INFORMATION Figure 1 : Voltage follower Figure 2 : Gain-of-10 inverting amplifier 10k 1k - TL 0 6 2 Ω - eI 1/2 Ω eo 1/2 eo TL062 R L = 10k Ω C L = 100pF eI RL C L = 100pF TYPICAL APPLICATION 100KHz QUADRATURE OSCILLATOR 1N 4148 18k Ω * -15V 1k Ω 18pF 18pF - 1/2 88.4k Ω - TL062 1/2 88.4k Ω 6 sin ω t 6 cos ω t TL062 1k Ω 18pF 88.4k Ω 1N 4148 18k Ω * +15V * These resistor values may be adjusted for a symmetrical output 8/10 TL062 - TL062A - TL062B PM-DIP8.EPS PACKAGE MECHANICAL DATA 8 PINS - PLASTIC DIP A a1 B b b1 D E e e3 e4 F i L Z Min. Millimeters Typ. 3.32 0.51 1.15 0.356 0.204 Max. 1.65 0.55 0.304 10.92 9.75 7.95 Min. 0.020 0.045 0.014 0.008 Max. 0.065 0.022 0.012 0.430 0.384 0.313 2.54 7.62 7.62 3.18 Inches Typ. 0.131 0.100 0.300 0.300 6.6 5.08 3.81 1.52 0.125 0260 0.200 0.150 0.060 DIP8.TBL Dimensions 9/10 TL062 - TL062A - TL062B PM-SO8.EPS PACKAGE MECHANICAL DATA 8 PINS - PLASTIC MICROPACKAGE (SO) A a1 a2 a3 b b1 C c1 D E e e3 F L M S Min. Millimeters Typ. 0.1 0.65 0.35 0.19 0.25 Max. 1.75 0.25 1.65 0.85 0.48 0.25 0.5 Min. Inches Typ. 0.026 0.014 0.007 0.010 Max. 0.069 0.010 0.065 0.033 0.019 0.010 0.020 0.189 0.228 0.197 0.244 0.004 o 45 (typ.) 4.8 5.8 5.0 6.2 1.27 3.81 3.8 0.4 0.050 0.150 4.0 1.27 0.6 0.150 0.016 0.157 0.050 0.024 o 8 (max.) SO8.TBL Dimensions 1997 SGS-THOMSON Microelectronics – Printed in Italy – All Rights Reserved SGS-THOM SON Microelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco The Netherlands - Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. 10/10 ORDER CODE : Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of SGS-THOMSON Microelectronics.