TL494, NCV494 SWITCHMODE™ Pulse Width Modulation Control Circuit The TL494 is a fixed frequency, pulse width modulation control circuit designed primarily for SWITCHMODE power supply control. Features • • • • • • • • • • Complete Pulse Width Modulation Control Circuitry On−Chip Oscillator with Master or Slave Operation On−Chip Error Amplifiers On−Chip 5.0 V Reference Adjustable Deadtime Control Uncommitted Output Transistors Rated to 500 mA Source or Sink Output Control for Push−Pull or Single−Ended Operation Undervoltage Lockout NCV Prefix for Automotive and Other Applications Requiring Site and Control Changes Pb−Free Packages are Available* http://onsemi.com MARKING DIAGRAMS 16 SOIC−16 D SUFFIX CASE 751B TL494xDG AWLYWW 1 16 PDIP−16 * N SUFFIX CASE 648 1 TL494xN AWLYYWWG MAXIMUM RATINGS (Full operating ambient temperature range applies, unless otherwise noted.) Rating Symbol Value Unit Power Supply Voltage VCC 42 V Collector Output Voltage VC1, VC2 42 V Collector Output Current (Each transistor) (Note 1) IC1, IC2 500 mA Amplifier Input Voltage Range VIR −0.3 to +42 Power Dissipation @ TA ≤ 45°C x A WL YY, Y WW, W G *This marking diagram also applies to NCV494. V PD 1000 mW RqJA 80 °C/W Operating Junction Temperature TJ 125 °C Noninv Input 1 Storage Temperature Range Tstg −55 to +125 °C Inv Input 2 Operating Ambient Temperature Range TL494B TL494C TL494I NCV494B TA Derating Ambient Temperature TA Thermal Resistance, Junction−to−Ambient = B, C or I = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package °C −40 to +125 0 to +70 −40 to +85 −40 to +125 Compen/PWN Comp Input 3 Deadtime Control 4 + Error 1 Amp − + 2 Error Amp − VCC 5.0 V REF ≈ 0.1 V Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. 1. Maximum thermal limits must be observed. Noninv 16 Input Inv 15 Input 14 Vref Output 13 Contro l 12 VCC CT 5 °C 45 PIN CONNECTIONS Oscillator 11 C2 RT 6 Q2 Ground 7 C1 8 10 E2 Q1 9 E1 (Top View) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. © Semiconductor Components Industries, LLC, 2005 June, 2005 − Rev. 6 1 Publication Order Number: TL494/D TL494, NCV494 RECOMMENDED OPERATING CONDITIONS Characteristics Symbol Min Typ Max Unit VCC 7.0 15 40 V VC1, VC2 − 30 40 V IC1, IC2 − − 200 mA Amplified Input Voltage Vin −0.3 − VCC − 2.0 V Current Into Feedback Terminal lfb − − 0.3 mA Reference Output Current lref − − 10 mA Power Supply Voltage Collector Output Voltage Collector Output Current (Each transistor) Timing Resistor RT 1.8 30 500 kW Timing Capacitor CT 0.0047 0.001 10 mF Oscillator Frequency fosc 1.0 40 200 kHz ELECTRICAL CHARACTERISTICS (VCC = 15 V, CT = 0.01 mF, RT = 12 kW, unless otherwise noted.) For typical values TA = 25°C, for min/max values TA is the operating ambient temperature range that applies, unless otherwise noted. Characteristics Symbol Min Typ Max Unit Vref 4.75 5.0 5.25 V Line Regulation (VCC = 7.0 V to 40 V) Regline − 2.0 25 mV Load Regulation (IO = 1.0 mA to 10 mA) Regload − 3.0 15 mV Short Circuit Output Current (Vref = 0 V) ISC 15 35 75 mA Collector Off−State Current (VCC = 40 V, VCE = 40 V) IC(off) − 2.0 100 mA Emitter Off−State Current VCC = 40 V, VC = 40 V, VE = 0 V) IE(off) − − −100 mA Vsat(C) Vsat(E) − − 1.1 1.5 1.3 2.5 IOCL IOCH − − 10 0.2 − 3.5 − − 100 100 200 200 − − 25 40 100 100 REFERENCE SECTION Reference Voltage (IO = 1.0 mA) OUTPUT SECTION Collector−Emitter Saturation Voltage (Note 2) Common−Emitter (VE = 0 V, IC = 200 mA) Emitter−Follower (VC = 15 V, IE = −200 mA) V Output Control Pin Current Low State (VOC v 0.4 V) High State (VOC = Vref) Output Voltage Rise Time Common−Emitter (See Figure 12) Emitter−Follower (See Figure 13) tr Output Voltage Fall Time Common−Emitter (See Figure 12) Emitter−Follower (See Figure 13) tf mA mA ns ns 2. Low duty cycle pulse techniques are used during test to maintain junction temperature as close to ambient temperature as possible. http://onsemi.com 2 TL494, NCV494 ELECTRICAL CHARACTERISTICS (VCC = 15 V, CT = 0.01 mF, RT = 12 kW, unless otherwise noted.) For typical values TA = 25°C, for min/max values TA is the operating ambient temperature range that applies, unless otherwise noted. Characteristics Symbol Min Typ Max Unit ERROR AMPLIFIER SECTION Input Offset Voltage (VO (Pin 3) = 2.5 V) VIO − 2.0 10 mV Input Offset Current (VO (Pin 3) = 2.5 V) IIO − 5.0 250 nA Input Bias Current (VO (Pin 3) = 2.5 V) IIB − −0.1 −1.0 mA Input Common Mode Voltage Range (VCC = 40 V, TA = 25°C) VICR −0.3 to VCC−2.0 V Open Loop Voltage Gain (DVO = 3.0 V, VO = 0.5 V to 3.5 V, RL = 2.0 kW) AVOL 70 95 − dB Unity−Gain Crossover Frequency (VO = 0.5 V to 3.5 V, RL = 2.0 kW) fC− − 350 − kHz Phase Margin at Unity−Gain (VO = 0.5 V to 3.5 V, RL = 2.0 kW) fm − 65 − deg. Common Mode Rejection Ratio (VCC = 40 V) CMRR 65 90 − dB Power Supply Rejection Ratio (DVCC = 33 V, VO = 2.5 V, RL = 2.0 kW) PSRR − 100 − dB Output Sink Current (VO (Pin 3) = 0.7 V) IO− 0.3 0.7 − mA Output Source Current (VO (Pin 3) = 3.5 V) IO+ 2.0 −4.0 − mA VTH − 2.5 4.5 V II− 0.3 0.7 − mA Input Bias Current (Pin 4) (VPin 4 = 0 V to 5.25 V) IIB (DT) − −2.0 −10 mA Maximum Duty Cycle, Each Output, Push−Pull Mode (VPin 4 = 0 V, CT = 0.01 mF, RT = 12 kW) (VPin 4 = 0 V, CT = 0.001 mF, RT = 30 kW) DCmax 45 − 48 45 50 50 − 0 2.8 − 3.3 − fosc − 40 − kHz PWM COMPARATOR SECTION (Test Circuit Figure 11) Input Threshold Voltage (Zero Duty Cycle) Input Sink Current (V(Pin 3) = 0.7 V) DEADTIME CONTROL SECTION (Test Circuit Figure 11) Input Threshold Voltage (Pin 4) (Zero Duty Cycle) (Maximum Duty Cycle) % Vth V OSCILLATOR SECTION Frequency (CT = 0.001 mF, RT = 30 kW) Standard Deviation of Frequency* (CT = 0.001 mF, RT = 30 kW) sfosc − 3.0 − % Frequency Change with Voltage (VCC = 7.0 V to 40 V, TA = 25°C) Dfosc (DV) − 0.1 − % Frequency Change with Temperature (DTA = Tlow to Thigh) (CT = 0.01 mF, RT = 12 kW) Dfosc (DT) − − 12 % Vth 5.5 6.43 7.0 V − − 5.5 7.0 10 15 − 7.0 − UNDERVOLTAGE LOCKOUT SECTION Turn−On Threshold (VCC increasing, Iref = 1.0 mA) TOTAL DEVICE Standby Supply Current (Pin 6 at Vref, All other inputs and outputs open) (VCC = 15 V) (VCC = 40 V) Average Supply Current (CT = 0.01 mF, RT = 12 kW, V(Pin 4) = 2.0 V) (VCC = 15 V) (See Figure 12) ICC mA mA * Standard deviation is a measure of the statistical distribution about the mean as derived from the formula, s http://onsemi.com 3 N S (Xn − X)2 n=1 N−1 TL494, NCV494 ORDERING INFORMATION Package Shipping† TL494BD SOIC−16 48 Units / Rail TL494BDG SOIC−16 (Pb−Free) 48 Units / Rail TL494BDR2 SOIC−16 2500 Tape & Reel TL494BDR2G SOIC−16 (Pb−Free) 2500 Tape & Reel TL494CD SOIC−16 48 Units / Rail TL494CDG SOIC−16 (Pb−Free) 48 Units / Rail TL494CDR2 SOIC−16 2500 Tape & Reel TL494CDR2G SOIC−16 (Pb−Free) 2500 Tape & Reel TL494CN PDIP−16 25 Units / Rail TL494CNG PDIP−16 (Pb−Free) 25 Units / Rail TL494IN PDIP−16 25 Units / Rail TL494ING PDIP−16 (Pb−Free) 25 Units / Rail NCV494BDR2* SOIC−16 2500 Tape & Reel NCV494BDR2G* SOIC−16 (Pb−Free) 2500 Tape & Reel Device †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NCV494: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control. http://onsemi.com 4 TL494, NCV494 VCC Output Control 13 8 6 D Oscillator RT CT 5 − 0.12V Q Q1 Q Q2 11 Deadtime Comparator Ck + 4 Deadtime Control 9 Flip− Flop 10 0.7V − + 1 2 − 1 2 Error Amp 1 + PWM Comparator 0.7mA 12 − + 3 UV Lockout + − 3.5V 15 Feedback PWM Comparator Input Reference Regulator − + 16 14 Error Amp 2 Ref. Output This device contains 46 active transistors. Figure 1. Representative Block Diagram Capacitor CT Feedback/PWM Comp. Deadtime Control Flip−Flop Clock Input Flip−Flop Q Flip−Flop Q Output Q1 Emitter Output Q2 Emitter Output Control Figure 2. Timing Diagram http://onsemi.com 5 VCC 4.9V 7 Gnd TL494, NCV494 APPLICATIONS INFORMATION Description common mode input range from −0.3 V to (VCC − 2V), and may be used to sense power−supply output voltage and current. The error−amplifier outputs are active high and are ORed together at the noninverting input of the pulse−width modulator comparator. With this configuration, the amplifier that demands minimum output on time, dominates control of the loop. When capacitor CT is discharged, a positive pulse is generated on the output of the deadtime comparator, which clocks the pulse−steering flip−flop and inhibits the output transistors, Q1 and Q2. With the output−control connected to the reference line, the pulse−steering flip−flop directs the modulated pulses to each of the two output transistors alternately for push−pull operation. The output frequency is equal to half that of the oscillator. Output drive can also be taken from Q1 or Q2, when single−ended operation with a maximum on−time of less than 50% is required. This is desirable when the output transformer has a ringback winding with a catch diode used for snubbing. When higher output−drive currents are required for single−ended operation, Q1 and Q2 may be connected in parallel, and the output−mode pin must be tied to ground to disable the flip−flop. The output frequency will now be equal to that of the oscillator. The TL494 has an internal 5.0 V reference capable of sourcing up to 10 mA of load current for external bias circuits. The reference has an internal accuracy of $5.0% with a typical thermal drift of less than 50 mV over an operating temperature range of 0° to 70°C. The TL494 is a fixed−frequency pulse width modulation control circuit, incorporating the primary building blocks required for the control of a switching power supply. (See Figure 1.) An internal−linear sawtooth oscillator is frequency− programmable by two external components, RT and CT. The approximate oscillator frequency is determined by: fosc ≈ 1.1 RT • CT For more information refer to Figure 3. Output pulse width modulation is accomplished by comparison of the positive sawtooth waveform across capacitor CT to either of two control signals. The NOR gates, which drive output transistors Q1 and Q2, are enabled only when the flip−flop clock−input line is in its low state. This happens only during that portion of time when the sawtooth voltage is greater than the control signals. Therefore, an increase in control−signal amplitude causes a corresponding linear decrease of output pulse width. (Refer to the Timing Diagram shown in Figure 2.) The control signals are external inputs that can be fed into the deadtime control, the error amplifier inputs, or the feedback input. The deadtime control comparator has an effective 120 mV input offset which limits the minimum output deadtime to approximately the first 4% of the sawtooth−cycle time. This would result in a maximum duty cycle on a given output of 96% with the output control grounded, and 48% with it connected to the reference line. Additional deadtime may be imposed on the output by setting the deadtime−control input to a fixed voltage, ranging between 0 V to 3.3 V. fosc , OSCILLATOR FREQUENCY (Hz) 500 k Functional Table Input/Output Controls Output Function fout fosc = Grounded Single−ended PWM @ Q1 and Q2 1.0 Push−pull Operation 0.5 @ Vref CT = 0.001 mF 100 k 0.01 mF 10 k 0.1 mF 1.0 k 500 1.0 k 2.0 k 5.0 k The pulse width modulator comparator provides a means for the error amplifiers to adjust the output pulse width from the maximum percent on−time, established by the deadtime control input, down to zero, as the voltage at the feedback pin varies from 0.5 V to 3.5 V. Both error amplifiers have a VCC = 15 V 10 k 20 k 50 k 100 k 200 k RT, TIMING RESISTANCE (W) 500 k 1.0 M Figure 3. Oscillator Frequency versus Timing Resistance http://onsemi.com 6 VCC = 15 V DVO = 3.0 V RL = 2.0 kW AVOL 10 100 1.0 k 10 k f, FREQUENCY (Hz) % DT, PERCENT DEADTIME (EACH OUTPUT) 120 110 100 90 80 70 60 50 40 30 20 10 0 1.0 φ , EXCESS PHASE (DEGREES) A VOL , OPEN LOOP VOLTAGE GAIN (dB) TL494, NCV494 0 20 40 60 80 φ 100 120 140 160 180 100 k 1.0 M 20 18 16 CT = 0.001 mF 14 12 10 8.0 6.0 0.001 mF 4.0 2.0 0 500 k 1.0 k 50 1.9 1 40 VCC = 15 V VOC = Vref 1.CT = 0.01 mF 2.RT = 10 kW 2.CT = 0.001 mF 2.RT = 30 kW 2 30 20 10 0 0 1.0 2.0 3.0 1.8 1.7 1.6 1.5 1.4 1.3 1.2 1.1 3.5 0 100 VDT, DEADTIME CONTROL VOLTAGE (IV) Figure 6. Percent Duty Cycle versus Deadtime Control Voltage 200 300 IE, EMITTER CURRENT (mA) 400 Figure 7. Emitter−Follower Configuration Output Saturation Voltage versus Emitter Current 10 2.0 9.0 I CC , SUPPLY CURRENT (mA) VCE(sat), SATURATION VOLTAGE (V) 500 k Figure 5. Percent Deadtime versus Oscillator Frequency V CE(sat) , SATURATION VOLTAGE (V) % DC, PERCENT DUTY CYCLE (EACH OUTPUT) Figure 4. Open Loop Voltage Gain and Phase versus Frequency 10 k 100 k fosc, OSCILLATOR FREQUENCY (Hz) 1.6 1.4 1.2 1.8 1.0 0.8 0.6 8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0 0.4 0 100 200 300 IC, COLLECTOR CURRENT (mA) 0 400 5.0 10 15 20 25 30 35 VCC, SUPPLY VOLTAGE (V) Figure 8. Common−Emitter Configuration Output Saturation Voltage versus Collector Current Figure 9. Standby Supply Current versus Supply Voltage http://onsemi.com 7 40 TL494, NCV494 VCC = 15V + Vin Error Amplifier Under Test Test Inputs Feedback RT CT (+) (−) Error (+) (−) Output Control Gnd − Feedback Terminal (Pin 3) + Vref − Other Error Amplifier 50k Figure 10. Error−Amplifier Characteristics 150 2W VCC Deadtime 150 2W C1 E1 Output 1 C2 E2 Output 2 Ref Out Figure 11. Deadtime and Feedback Control Circuit 15V 15V RL 68 C Each Output Transistor C VC Each Output Transistor CL 15pF Q Q VEE E RL 68 E 90% VEE 90% 90% 90% CL 15pF VCC 10% 10% tr Gnd 10% 10% tr tf tf Figure 13. Emitter−Follower Configuration Test Circuit and Waveform Figure 12. Common−Emitter Configuration Test Circuit and Waveform http://onsemi.com 8 TL494, NCV494 VO Vref To Output Voltage of System 1 Vref Error Amp + − R2 − 2 Error Amp 3 R1 Negative Output Voltage 2 VO = Vref Positive Output Voltage R2 1 + R1 R1 R2 VO To Output Voltage of System R1 R2 VO = Vref 1 + Figure 14. Error−Amplifier Sensing Techniques Output Control R1 Vref Output DT Q CT RT 6 4 R2 5 DT Q 0.001 30k CS Vref Output 4 RS 80 Max. % on Time, each output ≈ 45 − 1 + R1 R2 Figure 15. Deadtime Control Circuit Figure 16. Soft−Start Circuit C1 C1 QC Q1 2.4 V ≤ VOC ≤ Vref Q1 E1 Output Control Push−Pull C2 0 ≤ VOC ≤ 0.4 V Q2 E2 1.0 mA to 250 mA Output Control 1.0 mA to 500 mA Single−Ended E1 C2 Q2 QE Figure 17. Output Connections for Single−Ended and Push−Pull Configurations http://onsemi.com 9 E2 1.0 mA to 250 mA TL494, NCV494 Vref 6 5 RT RT VCC RS Master CT 12 Vin > 40V CT 1N975A VZ = 39V 5.0V Ref Vref 270 6 RT 5 Slave (Additional Circuits) CT Gnd 7 Figure 18. Slaving Two or More Control Circuits Figure 19. Operation with Vin > 40 V Using External Zener +Vin = 8.0V to 20V 12 1 2 1M 33k 3 0.01 0.01 15 16 47 VCC + C1 − Tip 32 TL494 Comp − C2 + 8 T1 OC VREF DT 13 14 4 CT 5 E1 RT Gnd 6 7 9 E2 11 Tip 32 22 k L1 + 50 35V 4.7k + 50 25V 47 1.0 1N4934 10 + 4.7k 4.7k +VO = 28 V IO = 0.2 A 1N4934 + 50 35V 240 10 10k 15k 0.001 All capacitors in mF Figure 20. Pulse Width Modulated Push−Pull Converter Test Conditions Results Line Regulation Vin = 10 V to 40 V 14 mV 0.28% Load Regulation Vin = 28 V, IO = 1.0 mA to 1.0 A 3.0 mV 0.06% Output Ripple Vin = 28 V, IO = 1.0 A 65 mV pp P.A.R.D. Short Circuit Current Vin = 28 V, RL = 0.1 W 1.6 A Efficiency Vin = 28 V, IO = 1.0 A 71% http://onsemi.com 10 L1 − 3.5 mH @ 0.3 A T1 − Primary: 20T C.T. #28 AWG T1 − Secondary: 12OT C.T. #36 AWG T1 − Core: Ferroxcube 1408P−L00−3CB TL494, NCV494 1.0mH @ 2A +Vin = 10V to 40V +VO = 5.0 V Tip 32A IO = 1.0 A 47 150 12 8 VCC 50 50V 47k 0.1 11 C1 C2 + TL494 CT 5 3 Comp − 2 + 1 Vref D.T. O.C. Gnd E1 6 4 13 7 9 5.1k 5.1k 14 − 15 16 + RT 1.0M 500 10V MR850 5.1k E2 + 10 150 0.001 47k 0.1 Figure 21. Pulse Width Modulated Step−Down Converter Test + Conditions Line Regulation Vin = 8.0 V to 40 V Load Regulation Vin = 12.6 V, IO = 0.2 mA to 200 mA Output Ripple Vin = 12.6 V, IO = 200 mA Short Circuit Current Vin = 12.6 V, RL = 0.1 W Efficiency Vin = 12.6 V, IO = 200 mA http://onsemi.com 11 Results 3.0 mV 0.01% 5.0 mV 0.02% 40 mV pp P.A.R.D. 250 mA 72% 50 10V TL494, NCV494 PACKAGE DIMENSIONS SOIC−16 D SUFFIX CASE 751B−05 ISSUE J NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. −A− 16 9 −B− 1 P 8 PL 0.25 (0.010) 8 M B S G R K F X 45 _ C −T− SEATING PLANE J M D 16 PL 0.25 (0.010) M T B S A S http://onsemi.com 12 DIM A B C D F G J K M P R MILLIMETERS MIN MAX 9.80 10.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.229 0.244 0.010 0.019 TL494, NCV494 PACKAGE DIMENSIONS PDIP−16 N SUFFIX CASE 648−08 ISSUE T NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. −A− 16 9 1 8 B F C L S −T− SEATING PLANE K H G D M J 16 PL 0.25 (0.010) M T A M http://onsemi.com 13 DIM A B C D F G H J K L M S INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01 TL494, NCV494 SWITCHMODE is a trademark of Semiconductor Components Industries, LLC. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 61312, Phoenix, Arizona 85082−1312 USA Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder Japan: ON Semiconductor, Japan Customer Focus Center 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Phone: 81−3−5773−3850 http://onsemi.com 14 For additional information, please contact your local Sales Representative. TL494/D