TLE42764 Low Dropout Linear Voltage Regulator TLE42764GV50 TLE42764DV50 TLE42764EV50 TLE42764GV TLE42764DV Data Sheet Rev. 1.2, 2011-02-15 Automotive Power Low Dropout Linear Voltage Regulator 1 TLE42764 Overview Features • • • • • • • • • • • Very Low Current Consumption Adjustable and 5 V Fixed Output Voltage ±2% Output Current up to 400 mA Enable Input Very Low Dropout Voltage Output Current Limitation Overtemperature Shutdown Reverse Polarity Protection Wide Temperature Range From -40 °C up to 150 °C Green Product (RoHS compliant) AEC Qualified PG-TO263-5 Description The TLE42764 is a monolithic integrated low dropout voltage regulator for load currents up to 400 mA. An input voltage up to 40 V is regulated to an adjustable or 5 V fixed voltage with a precision of ±2%. The device is designed for the harsh environment of automotive applications. Therefore it is protected against overload, short circuit and overtemperature conditions by the implemented output current limitation and the overtemperature shutdown circuit. The TLE42764 can be also used in all other applications requiring a stabilized voltage between 2.5 V and 20 V. PG-TO252-5 Due to its very low quiescent current the TLE42764 is dedicated for use in applications permanently connected to VBAT. In addition the device can be switched off via the Enable input reducing the current consumption to less than 10 μA. PG-SSOP-14 exposed pad Type Package Marking TLE42764GV50 PG-TO263-5 42764V5 TLE42764DV50 PG-TO252-5 42764V5 TLE42764GV PG-TO263-5 42764V TLE42764DV PG-TO252-5 42764V TLE42764EV50 PG-SSOP-14 exposed pad 42764V5 Data Sheet 2 Rev. 1.2, 2011-02-15 TLE42764 Block Diagram 2 Block Diagram Saturation Control and Protection Circuit Temperature Sensor Ι 1 5 Control Amplifier Q Buffer Bandgap Reference *) **) 2 4 3 EN VA GND *) For fixed Voltage Regulator only **) For adjustable Voltage Regulator only Figure 1 Data Sheet AEB02044 Block Diagram 3 Rev. 1.2, 2011-02-15 TLE42764 Pin Configuration 3 Pin Configuration 3.1 Pin Assignment PG-TO263-5, PG-TO252-5 GND GND 1 5 I 1 2 3 4 5 Q EN n.c. VA I GND Q EN n.c. VA AEP02560 PinConfig_PG-TO-263-5-1.vsd Figure 2 Pin Configuration (top view) 3.2 Pin Definitions and Functions PG-TO263-5, PG-TO252-5 Pin No. Symbol Function 1 I Input block to ground directly at the IC with a ceramic capacitor 2 EN Enable Input high level input signal enables the IC; low level input signal disables the IC; integrated pull-down resistor 3 GND Ground internally connected to heat slug 4 n.c. not connected for TLE42764GV50, TLE42764DV50 can be open or connected to GND Voltage Adjust Input for TLE42764GV, TLE42764DV connect external voltage divider to configure the output voltage VA 5 Q Output block to ground with a capacitor close to the IC terminals, respecting the values given for its capacitance and ESR in “Functional Range” on Page 7 Heat Slug – Heat Slug internally connected to GND; connect to GND and heatsink area Data Sheet 4 Rev. 1.2, 2011-02-15 TLE42764 Pin Configuration 3.3 Pin Assignment PG-SSOP-14 exposed pad n.c. EN 1 14 2 13 n.c. I n.c. 3 12 n.c. GND 4 11 n.c. n.c. 5 10 n.c. n.c. 6 9 Q n.c. 7 8 n.c. PINCONFIG_SSOP-14.SVG Figure 3 Pin Configuration (top view) 3.4 Pin Definitions and Functions PG-SSOP-14 exposed pad Pin No. Symbol Function 1, 3, 5-7 n.c. non connected can be open or connected to GND 2 EN Enable Input high level input signal enables the IC; low level input signal disables the IC; integrated pull-down resistor 4 GND Ground 8, 10-12, 14 n.c. non connected can be open or connected to GND 9 Q Output block to ground with a capacitor close to the IC terminals, respecting the values given for its capacitance and ESR in “Functional Range” on Page 7 13 I Input block to ground directly at the IC with a ceramic capacitor Exposed Pad – Exposed Pad connect to GND and heatsink area Data Sheet 5 Rev. 1.2, 2011-02-15 TLE42764 General Product Characteristics 4 General Product Characteristics 4.1 Absolute Maximum Ratings Table 1 Absolute Maximum Ratings1) Tj = -40 °C to 150 °C; all voltages with respect to ground, (unless otherwise specified) Pos. Parameter Symbol Limit Values Unit Test Condition Min. Max. VI -42 45 V – Voltage VVA -0.3 10 V – Voltage VQ -1 40 V – Tj Tstg -40 150 °C – -50 150 °C – VESD,HBM -3 3 kV Human Body Model (HBM)2) VESD,CDM -1000 1000 V Charge Device Model (CDM)3) at all pins Input I, Enable EN 4.1.1 Voltage Voltage Adjust Input VA 4.1.2 Output Q 4.1.3 Temperature 4.1.4 Junction temperature 4.1.5 Storage temperature ESD Susceptibility 4.1.6 ESD Absorption 4.1.7 1) not subject to production test, specified by design 2) ESD susceptibility Human Body Model “HBM” according to AEC-Q100-002 - JESD22-A114 3) ESD susceptibility Charged Device Model “CDM” according to ESDA STM5.3.1 Note: Stresses above the ones listed here may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Note: Integrated protection functions are designed to prevent IC destruction under fault conditions described in the data sheet. Fault conditions are considered as “outside” normal operating range. Protection functions are not designed for continuous repetitive operation. Data Sheet 6 Rev. 1.2, 2011-02-15 TLE42764 General Product Characteristics 4.2 Functional Range Table 2 Functional Range Pos. Parameter Symbol Limit Values Min. Max. Unit Remarks 4.2.1 Input voltage VI 5.5 40 V TLE42764GV50, TLE42764DV50, TLE42764EV50 4.2.2 Input voltage VI VQ + 0.5 40 V TLE42764GV, TLE42764DV; VQ > 4 V 4.2.3 Input voltage VI 4.5 40 V TLE42764GV, TLE42764DV; VQ < 4 V 4.2.4 – µF 1) – 3 Ω 2) 4.2.6 Junction temperature CQ ESR(CQ) Tj 22 4.2.5 Output Capacitor’s Requirements for Stability -40 150 °C – 1) The minimum output capacitance requirement is applicable for a worst case capacitance tolerance of 30% 2) Relevant ESR value at f = 10 kHz Note: Within the functional or operating range, the IC operates as described in the circuit description. The electrical characteristics are specified within the conditions given in the Electrical Characteristics table. Data Sheet 7 Rev. 1.2, 2011-02-15 TLE42764 General Product Characteristics 4.3 Thermal Resistance Note: This thermal data was generated in accordance with JEDEC JESD51 standards. For more information, go to www.jedec.org. Table 3 Pos. Thermal Resistance Parameter Symbol Limit Values Min. Typ. Max. Unit Conditions TLE42764GV, TLE42764GV50 (PG-TO263-5) 4.3.1 Junction to Case1) RthJC – 3.6 – K/W measured to heat slug 4.3.2 Junction to Ambient1) RthJA – 22 – K/W 2) 4.3.3 – 74 – K/W footprint only3) 4.3.4 – 42 – K/W 300 mm² heatsink area3) 4.3.5 – 34 – K/W 600 mm² heatsink area3) TLE42764DV, TLE42764DV50 (PG-TO252-5) 4.3.6 Junction to Case1) RthJC – 3.6 – K/W measured to heat slug 4.3.7 Junction to Ambient1) RthJA – 27 – K/W 2) 4.3.8 – 115 – K/W footprint only3) 4.3.9 – 52 – K/W 300 mm² heatsink area3) 4.3.10 – 40 – K/W 600 mm² heatsink area3) – 7 – K/W – – 41 – K/W 2) 4.3.13 – 130 – K/W footprint only3) 4.3.14 – 60 – K/W 300 mm2 heatsink area on PCB3) 4.3.15 – 50 – K/W 600 mm2 heatsink area on PCB3) TLE42764EV50 (PG-SSOP-14 exposed pad) 4.3.11 Junction to Case1) 4.3.12 Junction to Ambient1) RthJC RthJA 1) Not subject to production test, specified by design. 2) Specified RthJA value is according to Jedec JESD51-2,-5,-7 at natural convection on FR4 2s2p board; The Product (Chip+Package) was simulated on a 76.2 x 114.3 x 1.5 mm³ board with 2 inner copper layers (2 x 70µm Cu, 2 x 35µm Cu). Where applicable a thermal via array under the exposed pad contacted the first inner copper layer. 3) Specified RthJA value is according to Jedec JESD 51-3 at natural convection on FR4 1s0p board; The Product (Chip+Package) was simulated on a 76.2 × 114.3 × 1.5 mm3 board with 1 copper layer (1 x 70µm Cu). Data Sheet 8 Rev. 1.2, 2011-02-15 TLE42764 Electrical Characteristics 5 Electrical Characteristics 5.1 Electrical Characteristics Voltage Regulator Table 4 Electrical Characteristics VI =13.5 V; Tj = -40 °C to 150 °C; all voltages with respect to ground (unless otherwise specified) Pos. Parameter Symbol Limit Values Min. Typ. Max. Unit Measuring Condition Output Q 5.1.1 Output Voltage VQ 4.9 5.0 5.1 V TLE42764GV50, TLE42764DV50, TLE42764EV50 5 mA < IQ< 400 mA 6 V < VI < 28 V 5.1.2 Output Voltage VQ 4.9 5.0 5.1 V 5.1.3 Output Voltage1) ΔV Q TLE42764GV50, TLE42764DV50, TLE42764EV50 5 mA < IQ<200 mA 6 V < VI < 40 V -2 – 2 % TLE42764GV, TLE42764DV; R2 < 50 kΩ; VQ + 1 V ≤ VI ≤ 40V; VI > 4.5 V; 5 mA ≤ IQ ≤ 400 mA 5.1.4 Output Voltage Adjustable Range3) VQ,range 2.5 – 20 V TLE42764GV, TLE42764DV; see Page 14 5.1.5 Dropout Voltage Vdr – 250 500 mV TLE42764GV50, TLE42764DV50, TLE42764EV50; IQ = 250 mA Vdr = VI – VQ2) 5.1.6 Dropout Voltage Vdr – 250 500 mV TLE42764GV, TLE42764DV; IQ = 250 mA; VI > 4.5 V; Vdr = VI – VQ2) 5.1.7 Load Regulation ΔVQ, lo – 5 35 mV IQ = 5 mA to 400 mA; VI = 6 V TLE42764GV50, TLE42764DV50, TLE42764EV50; VI = 4.5 V TLE42764GV, TLE42764DV 5.1.8 Line Regulation ΔVQ, li – 15 25 mV Vl = 12 V to 32 V IQ = 5 mA 5.1.9 Output Current Limitation IQ 400 600 1100 mA 2) 5.1.10 Power Supply Ripple Rejection3) PSRR – 54 – dB fr = 100 Hz; Vr = 0.5 Vpp Data Sheet 9 Rev. 1.2, 2010-04-28 TLE42764 Electrical Characteristics Table 4 Electrical Characteristics VI =13.5 V; Tj = -40 °C to 150 °C; all voltages with respect to ground (unless otherwise specified) Pos. Parameter Symbol Limit Values Unit Measuring Condition Min. Typ. Max. dV Q ----------dT – 0.5 – mV/K – Current Consumption, Regulator Disabled Iq – – 10 μA VEN = 0 V 5.1.13 Quiescent Current Iq = II – IQ Iq – 100 220 μA IQ = 1 mA; VEN = 5 V 5.1.14 Current Consumption Iq = II – IQ Iq – 5 10 mA IQ = 250 mA; VEN = 5 V 5.1.15 Current Consumption Iq = II – IQ Iq – 15 25 mA IQ = 400 mA; VEN = 5 V 5.1.11 Temperature Output Voltage Drift 3) Current Consumption 5.1.12 Tj ≤ 100 °C 1) influence of resistor divider on precision neglected 2) Measured when the output voltage VQ has dropped 100 mV from the nominal value obtained at VI = 13.5 V. 3) not subject to production test, specified by design Data Sheet 10 Rev. 1.2, 2010-04-28 TLE42764 Electrical Characteristics 5.2 Typical Performance Characteristics Voltage Regulator Current Consumption Iq versus Output Current IQ Current Consumption Iq versus Low Output Current IQ 16 02_IQ_IQLOW.VSD 1,4 01_IQ_IQ.VSD 14 1,2 V I = 13.5 V T j = 25 °C 12 V I = 13.5 V T j = 25 °C 1 I q [mA] I q [mA] 10 8 6 0,8 0,6 0,4 4 2 0,2 0 0 0 100 200 300 0 400 20 Output Voltage VQ versus Junction Temperature TJ 03_VQ_TJ.VSD 0,4 0,3 T j = 25 °C 400 0,2 350 0,1 300 0 -0,1 200 150 -0,3 100 -0,4 50 -0,5 80 120 T j = -40 °C 250 -0,2 40 T j = 150 °C 450 V DR [mV] ΔV Q [%] 100 04_VDR_IQ.VSD 500 I Q = 5 mA V I = 13.5 V 0 150 0 T j [°C] Data Sheet 80 Dropout Voltage Vdr versus Output Current IQ 0,5 0 60 I Q [mA] I Q [mA] -40 40 100 200 300 400 I Q [mA] 11 Rev. 1.2, 2010-04-28 TLE42764 Electrical Characteristics Dropout Voltage Vdr versus Junction Temperature Maximum Output Current IQ versus Input Voltage VI 05_VDR_TJ.VSD 500 450 800 400 I Q = 400 mA 350 300 I Q,max [mA] V DR [mV] 06_IQMAX_VI.VSD 900 250 200 I Q = 100 mA 150 700 T j = 25 °C 600 T j = -40 °C T j = 150 °C 500 400 300 100 200 V Q = V Q,nom - 100 mV I Q = 10 mA 50 100 0 -40 0 40 80 120 0 160 0 T j [°C] 10 20 30 40 V I [V] Region Of Stability: Output Capacitor’s ESR ESR(CQ) versus Output Current IQ ESR(C Q ) [Ω ] 10 07_ESR_IQ.VSD Unstable Region 1 C Q = 22 µF V I = 13.5 V Stable Region 0,1 0,01 0 100 200 300 400 I Q [mA] Data Sheet 12 Rev. 1.2, 2010-04-28 TLE42764 Electrical Characteristics 5.3 Electrical Characteristics Enable Function The Enable Function allows disabling/enabling the regulator via the input pin EN. The regulator is turned on in case the pin EN is connected to a voltage higher than VEN,H. This can be e.g. the battery voltage, whereby no additional pull-up resistor is needed. The regulator can be turned off by connecting the pin EN to a voltage less than VEN,L, e.g. GND. Table 5 Electrical Characteristics Enable VI =13.5 V; Tj = -40 °C to 150 °C; all voltages with respect to ground, positive current flowing into pin (unless otherwise specified) Pos. 5.3.16 Parameter Symbol VEN,H VEN,L IEN,H High Level Input Voltage 5.3.17 Low Level Input Voltage 5.3.18 High Level Input Current 5.4 Limit Values Unit Measuring Condition V VQ ≥ 4.9 V VQ ≤ 0.1 V VEN = 5 V Min. Typ. Max. 3.5 – – – – 0.5 V 5 10 20 µA Typical Performance Characteristics Enable Function Enabled Input Current IEN versus Input Voltage VI , EN=Off Enabled Input Current IEN versus Enabled Input Voltage VEN 600 10_IEN_VEN.VSD 80 09_IEN_VI.VSD V EN = 0.5 V 70 500 T j = 150 °C 60 400 I EN [µA] I EN [nA] 50 300 V EN = 0.3 V 40 T j = 150 °C T j = 25 °C 30 200 T j = -40 °C 20 100 10 V EN = 0.1 V 0 0 0 10 20 30 40 0 V I [V] Data Sheet 10 20 30 40 V EN [V] 13 Rev. 1.2, 2010-04-28 TLE42764 Application Information 6 Application Information Note: The following information is given as a hint for the implementation of the device only and shall not be regarded as a description or warranty of a certain functionality, condition or quality of the device. I 1 Input CI 2 4 3 GND *) Optional Figure 4 CQ TLE42764 EN e.g. KL 15 Output 5 Q for adjustable Voltage Regulator R 1*) *) VA Voltage Adjust R 2*) AES02046 Application Diagram A typical application circuit of the TLE42764 is shown in Figure 4. It shows a generic configuration of the voltage regulator, with the recommendable minimum number of components one should use. Theoretically, if there is no risk of high frequency noise at all, even the small input filter capacitor can be omitted. For a normal operation mode of the device the only required device is the output capacitor, for the TLE42764GV and the TLE42764DV additionally the resistor divider. However, depending on the application’s environment, additional components like an input buffer capacitor or a reverse polarity protection diode can be considered as well. Input Filter Capacitor A small ceramic capacitor (e.g. 100nF in Figure 4) at the device’s input helps filtering high frequency noise. To reach the best filter effect, this capacitor should be placed as close as possible to the device’s input pin. The input filter capacitor does not have an influence on the stability of the device’s regulation loop. Output Capacitor CQ The output capacitor is the only external component that is required in any case as it is a part of the device’s regulating loop. To maintain stability of this loop, the TLE42764 requires an output capacitor respecting the values given in “Functional Range” on Page 7. Adjusting the Output Voltage of Variable Output Regulators TLE42764GV, TLE42764DV The output voltage of the TLE42764GV and the TLE42764DV can be adjusted between 2.5 V and 20 V by an external resistor divider, connected to the voltage adjust pin VA. The pin VA is connected to the error amplifier comparing the voltage at this pin with the internal reference voltage of typically 2.5 V. Data Sheet 14 Rev. 1.2, 2011-02-15 TLE42764 Application Information 5 Q Internal Reference 2.5 V Typical Current and Saturation Control Vref CQ R1 22 µF 4 VA R2 AEB02804 Figure 5 External Components at Output for Variable Voltage Regulator The output voltage can be easily calculated, neglecting the current flowing into the VA pin: R1 + R2 V Q = ------------------- × V ref R2 where R 2 < 50 kΩ to neglect the current flowing into the VA pin, with: • • • Vref: internal reference voltage, typically 2.5V R1: resistor between regulator output Q and voltage adjust pin VA R2: resistor between voltage adjust pin VA and GND For a 2.5 V output voltage the output pin Q has to be directly connected to the adjust pin VA. Take into consideration, that the accuracy of the resistors R1 and R2 adds an additional error to the output voltage tolerance. Data Sheet 15 Rev. 1.2, 2011-02-15 TLE42764 Package Outlines 7 Package Outlines 4.4 10 ±0.2 1.27 ±0.1 A 8.5 1) B 0.05 2.4 0.1 2.7 ±0.3 4.7 ±0.5 7.55 1) 9.25 ±0.2 (15) 1±0.3 0...0.3 0...0.15 5 x 0.8 ±0.1 0.5 ±0.1 4 x 1.7 0.25 M A B 8˚ MAX. 1) Typical Metal surface min. X = 7.25, Y = 6.9 All metal surfaces tin plated, except area of cut. Figure 6 Data Sheet 0.1 B GPT09113 PG-TO263-5 16 Rev. 1.2, 2011-02-15 TLE42764 Package Outlines 6.5 +0.15 -0.05 A 1) 2.3 +0.05 -0.10 0.9 +0.20 -0.01 0...0.15 5 x 0.6 ±0.1 1.14 4.56 0.5 +0.08 -0.04 0.51 MIN. 0.15 MAX. per side B (5) 0.8 ±0.15 (4.24) 1 ±0.1 9.98 ±0.5 6.22 -0.2 5.7 MAX. 0.5 +0.08 -0.04 0.1 B 0.25 M A B 1) Includes mold flashes on each side. All metal surfaces tin plated, except area of cut. Figure 7 Data Sheet PG-TO252-5 17 Rev. 1.2, 2011-02-15 TLE42764 Package Outlines 0.19 +0.06 0.08 C 0.15 M C A-B D 14x 0.64 ±0.25 1 8 1 7 0.2 M D 8x Bottom View 3 ±0.2 A 14 6 ±0.2 D Exposed Diepad B 0.1 C A-B 2x 14 7 8 2.65 ±0.2 0.25 ±0.05 2) 0.1 C D 8˚ MAX. C 0.65 3.9 ±0.11) 1.7 MAX. Stand Off (1.45) 0 ... 0.1 0.35 x 45˚ 4.9 ±0.11) Index Marking 1) Does not include plastic or metal protrusion of 0.15 max. per side 2) Does not include dambar protrusion PG-SSOP-14-1,-2,-3-PO V02 Figure 8 PG-SSOP-14 exposed pad Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). For further information on alternative packages, please visit our website: http://www.infineon.com/packages. Data Sheet 18 Dimensions in mm Rev. 1.2, 2011-02-15 TLE42764 Revision History 8 Revision History Revision Date Changes 1.2 2011-02-15 Updated Version final Data Sheet: 5V Version TLE42764EV50 in PG-SSOP-14 exposed pad package and all related description added 1.1 2009-10-09 Updated Version final Data Sheet: 5V Versions in PG-TO252-5 and PG-TO263-5 package and all related description added In “Features” on Page 2 in text “and 5 V Fixed “added In “Description” on Page 2 “or 5 V fixed “added In table on bottom of page “Overview” on Page 2 2 product versions including package and marking added In “Functional Range” on Page 7 Item 4.2.1 added In “Electrical Characteristics Voltage Regulator” on Page 9 Item 5.1.1, Item 5.1.2 and Item 5.1.5 added; In Conditions of Item 5.1.7 “VI = 6 V TLE42764GV50, TLE42764DV50;” added 1.0 Data Sheet 2008-01-14 Initial Version final Data Sheet 19 Rev. 1.2, 2011-02-15 Edition 2011-02-15 Published by Infineon Technologies AG 81726 Munich, Germany © 2011 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered.