TI TLV2460CDBVR

 SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
D
D
D
D
D
D
D
D
D
D
TLV2460
DBV PACKAGE
(TOP VIEW)
Rail-to-Rail Output Swing
Gain Bandwidth Product . . . 6.4 MHz
± 80 mA Output Drive Capability
Supply Current . . . 500 µA/channel
Input Offset Voltage . . . 100 µV
Input Noise Voltage . . . 11 nV/√Hz
Slew Rate . . . 1.6 V/µs
Micropower Shutdown Mode
(TLV2460/3/5) . . . 0.3 µA/Channel
Universal Operational Amplifier EVM
Available in Q-Temp Automotive
HighRel Automotive Applications
Configuration Control/Print Support
Qualification to Automotive Standards
OUT
1
6
VDD+
GND
2
5
SHDN
IN+
3
4
IN −
description
The TLV246x is a family of low-power rail-to-rail input/output operational amplifiers specifically designed for
portable applications. The input common-mode voltage range extends beyond the supply rails for maximum
dynamic range in low-voltage systems. The amplifier output has rail-to-rail performance with high-output-drive
capability, solving one of the limitations of older rail-to-rail input/output operational amplifiers. This rail-to-rail
dynamic range and high output drive make the TLV246x ideal for buffering analog-to-digital converters.
The operational amplifier has 6.4 MHz of bandwidth and 1.6 V/µs of slew rate with only 500 µA of supply current,
providing good ac performance with low power consumption. Three members of the family offer a shutdown
terminal, which places the amplifier in an ultralow supply current mode (IDD = 0.3 µA/ch). While in shutdown,
the operational-amplifier output is placed in a high-impedance state. DC applications are also well served with
an input noise voltage of 11 nV/√Hz and input offset voltage of 100 µV.
This family is available in the low-profile SOT23, MSOP, and TSSOP packages. The TLV2460 is the first
rail-to-rail input/output operational amplifier with shutdown available in the 6-pin SOT23, making it perfect for
high-density circuits. The family is specified over an expanded temperature range (TA = − 40°C to 125°C) for
use in industrial control and automotive systems, and over the military temperature range
(TA = −55°C to 125°C) for use in military systems.
SELECTION GUIDE
DEVICE
VDD
[V]
VIO
[µV]
IDD/ch
[µA]
IIB
[pA]
GBW
[MHz]
SLEW RATE
[V/µs]
Vn, 1 kHz
[nV/√Hz]
IO
[mA]
SHUTDOWN
RAIL-RAIL
TLV246x(A)
2.7−6
150
550
1300
6.4
1.6
11
25
Y
I/O
TLV277x(A)
2.5−5.5
360
1000
2
5.1
10.5
17
6
Y
O
TLV247x(A)
2.7−6
250
600
2.5
2.8
1.5
15
20
Y
I/O
TLV245x(A)
2.7−6
20
23
500
0.22
0.11
52
10
Y
I/O
TLV225x(A)
2.7−8
200
35
1
0.2
0.12
19
3
—
—
TLV226x(A)
2.7−8
300
200
1
0.71
0.55
12
3
—
—
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  1998−2004, Texas Instruments Incorporated
!"#$%&'#! ( )*$$+!' &( #" ,*-.)&'#! /&'+0
$#/*)'( )#!"#$% '# (,+)")&'#!( ,+$ '1+ '+$%( #" +&( !('$*%+!'(
('&!/&$/ 2&$$&!'30 $#/*)'#! ,$#)+((!4 /#+( !#' !+)+((&$.3 !).*/+
'+('!4 #" &.. ,&$&%+'+$(0
! ,$#/*)'( )#%,.&!' '# 5
&.. ,&$&%+'+$( &$+ '+('+/
*!.+(( #'1+$2(+ !#'+/0 ! &.. #'1+$ ,$#/*)'( ,$#/*)'#!
,$#)+((!4 /#+( !#' !+)+((&$.3 !).*/+ '+('!4 #" &.. ,&$&%+'+$(0
WWW.TI.COM
1
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
TLV2460C/I/AI and TLV2461C/I/AI AVAILABLE OPTIONS
PACKAGED DEVICES
SOT-23†
SYMBOL
(DBV)
TA
VIOmax
AT 25°C
0°C to 70°C
2000 µV
TLV2460CD
TLV2461CD
TLV2460CDBV
TLV2461CDBV
VAOC
VAPC
TLV2460CP
TLV2461CP
2000 µV
TLV2460ID
TLV2461ID
TLV2460IDBV
TLV2461IDBV
VAOI
VAPI
TLV2460IP
TLV2461IP
1500 µV
TLV2460AID
TLV2461AID
SMALL OUTLINE
(D)
−40°C to 125°C
—
—
PLASTIC DIP
(P)
—
—
TLV2460AIP
TLV2461AIP
† This package is available taped and reeled. To order this packaging option, add an R suffix to the part number (e.g., TLV2460CDR).
‡ Chip forms are tested at TA = 25°C only.
TLV2460M/AM/Q/AQ and TLV2461M/AM/Q/AQ AVAILABLE OPTIONS
PACKAGED DEVICES
TA
VIOmax
AT 25°C
SMALL
OUTLINE†
(D)
2000 µV
1500 µV
−40°C to 125°C
SMALL
OUTLINE†
(PW)
CERAMIC DIP
(JG)
CERAMIC
FLATPACK
(U)
CHIP CARRIER
(FK)
TLV2460QD
TLV2461QD
TLV2460QPW
TLV2461QPW
—
—
—
—
—
—
TLV2460AQD
TLV2461AQD
TLV2460AQPW
TLV2461AQPW
—
—
—
—
—
—
2000 µV
—
—
—
—
TLV2460MJG
TLV2461MJG
TLV2460MU
TLV2461MU
TLV2460MFK
TLV2461MFK
1500 µV
—
—
—
—
TLV2460AMJG
TLV2461AMJG
TLV2460AMU
TLV2461AMU
TLV2460AMFK
TLV2461AMFK
−55°C to 125°C
† This package is available taped and reeled. To order this packaging option, add an R suffix to the part number (e.g., TLV2460QDR).
TLV2462C/I/AI and TLV2463C/I/AI AVAILABLE OPTIONS
PACKAGED DEVICES
TA
VIOmax
AT 25°C
SMALL
OUTLINE†
(D)
MSOP
(DGK)
0°C to 70°C
2000 µV
TLV2462CD
TLV2463CD
TLV2462CDGK
—
2000 µV
TLV2462ID
TLV2463ID
1500 µV
TLV2462AID
TLV2463AID
−40
C to
−40°C
125°C
MSOP†
(DGS)
SYMBOL
PLASTIC DIP
(N)
PLASTIC DIP
(P)
xxTIAAI
—
TLV2463CDGS
—
xxTIAAK
—
TLV2463CN
TLV2462CP
—
TLV2462IDGK
—
xxTIAAJ
—
TLV2463IDGS
—
xxTIAAL
—
TLV2463IN
TLV2462IP
—
—
—
—
—
—
—
—
—
—
TLV2463AIN
TLV2462AIP
—
SYMBOL
† This package is available taped and reeled. To order this packaging option, add an R suffix to the part number (e.g., TLV2462CDR).
‡ Chip forms are tested at TA = 25°C only.
2
WWW.TI.COM
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
TLV2462M/AM/Q/AQ and TLV2463M/AM/Q/AQ AVAILABLE OPTIONS
PACKAGED DEVICES
TA
VIOmax
AT 25°C
SMALL
OUTLINE†
(D)
SMALL
OUTLINE†
(PW)
CERAMIC DIP
(JG)
CERAMIC
DIP
(J)
CERAMIC
FLATPACK
(U)
CHIP CARRIER
(FK)
2000 µV
TLV2462QD
TLV2463QD
TLV2462QPW
TLV2463QPW
—
—
—
—
—
—
—
—
1500 µV
TLV2462AQD
TLV2463AQD
TLV2462AQPW
TLV2463AQPW
—
—
—
—
—
—
—
—
−40°C to 125°C
2000 µV
—
—
—
—
TLV2462MJG
—
—
TLV2463MJ
TLV2462MU
TLV2462MFK
TLV2463MFK
1500 µV
—
—
—
—
TLV2462AMJG
—
—
TLV2463AMJ
TLV2462AMU
TLV2462AMFK
TLV2463AMFK
−55°C to 125°C
† This package is available taped and reeled. To order this packaging option, add an R suffix to the part number (e.g., TLV2462QDR).
TLV2464C/I/AI and TLV2465C/I/AI AVAILABLE OPTIONS
PACKAGED DEVICES
TA
VIOmax
AT 25°C
0°C to 70°C
2000 µV
TLV2464CD
TLV2465CD
TLV2464CN
TLV2465CN
TLV2464CPW
TLV2465CPW
2000 µV
TLV2464ID
TLV2465ID
TLV2464IN
TLV2465IN
TLV2464IPW
TLV2465IPW
1500 µV
TLV2464AID
TLV2465AID
TLV2464AIN
TLV2465AIN
TLV2464AIPW
TLV2465AIPW
−40°C to 125°C
SMALL OUTLINE
(D)
PLASTIC DIP
(N)
TSSOP
(PW)
† This package is available taped and reeled. To order this packaging option, add an R suffix to the part
number(e.g., TLV2464CDR).
‡ Chip forms are tested at TA = 25°C only.
TLV2464M/AM/Q/AQ and TLV2465M/AM/Q/AQ AVAILABLE OPTIONS
PACKAGED DEVICES
TA
VIOmax
AT 25°C
SMALL
OUTLINE†
(D)
2000 µV
1500 µV
- 40°C to 125°C
SMALL
OUTLINE†
(PW)
CERAMIC DIP
(J)
CHIP CARRIER
(FK)
TLV2464QD
TLV2465QD
TLV2464QPW
TLV2465QPW
—
—
—
—
TLV2464AQD
TLV2465AQD
TLV2464AQPW
TLV2465AQPW
—
—
—
—
2000 µV
—
—
—
—
TLV2464MJ
TLV2465MJ
TLV2464MFK
TLV2465MFK
1500 µV
—
—
—
—
TLV2464AMJ
TLV2465AMJ
TLV2464AMFK
TLV2465AMFK
−55°C to 125°C
† This package is available taped and reeled. To order this packaging option, add an R suffix to the part number
(e.g., TLV2464QDR).
WWW.TI.COM
3
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
TLV246x PACKAGE PINOUTS(1)
TLV2460
DBV PACKAGE
(TOP VIEW)
OUT
GND
IN+
1
2
3
6
5
4
VDD+
SHDN
IN −
TLV2461
D, P, JG, OR PW PACKAGE
(TOP VIEW)
NC
IN −
IN +
GND
1
8
2
7
3
6
4
5
TLV2460
D, P, JG, OR PW PACKAGE
(TOP VIEW)
TLV2461
DBV PACKAGE
(TOP VIEW)
NC
VDD+
OUT
NC
OUT
GND
IN+
1
5
VDD+
2
3
4
IN −
NC
IN −
IN +
GND
1
8
2
7
3
6
4
5
VDD+
2OUT
2IN −
2IN+
7
3
6
4
5
SHDN
VDD+
OUT
NC
1OUT
1IN −
1IN+
GND
1SHDN
1
2
3
4
5
10
9
8
7
6
VDD+
2OUT
2IN −
2IN+
2SHDN
TLV2463
D, N, J, OR PW PACKAGE
TLV2464
D, N, PWP, J, OR PW PACKAGE
TLV2465
D, N, PWP, J, OR PW PACKAGE
(TOP VIEW)
(TOP VIEW)
(TOP VIEW)
1OUT
1IN −
1IN+
GND
NC
1SHDN
NC
1
14
2
13
3
12
4
11
5
10
6
9
7
8
VDD+
2OUT
2IN −
2IN+
NC
2SHDN
NC
1OUT
1IN −
1IN+
VDD+
2IN+
2IN −
2OUT
1
14
2
13
3
4
5
12
11
10
6
9
7
8
4OUT
4IN −
4IN+
GND
3IN+
3IN −
3OUT
1OUT
1IN −
1IN+
VDD+
2IN+
2IN −
2OUT
1/2SHDN
NC − No internal connection
(1) SOT−23 may or may not be indicated
TYPICAL PIN 1 INDICATORS
Pin 1
Printed or
Molded Dot
4
8
2
TLV2463
DGS PACKAGE
(TOP VIEW)
TLV2462
D, DGK, P, JG, OR PW PACKAGE
(TOP VIEW)
1OUT
1IN −
1IN +
GND
1
Pin 1
Stripe
Pin 1
Bevel Edges
WWW.TI.COM
Pin 1
Molded ”U” Shape
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
4OUT
4IN −
4IN+
GND
3IN +
3IN−
3OUT
3/4SHDN
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
TLV246x PACKAGE PINOUTS (continued)(1)
TLV2461
U PACKAGE
(TOP VIEW)
5
17 VDD
IN−
5
17 VDD
NC
6
16 NC
NC
6
16 NC
IN+
7
15 OUT
IN+
7
NC
8
14 NC
NC
8
1IN+
4
18 2IN−
NC
5
17 NC
GND
6
16 2IN+
2OUT
18 2IN−
NC
5
17 NC
GND
6
16 2IN+
15 OUT
NC
7
15 NC
14 NC
NC
8
14 NC
10 11 12 13
NC
NC
NC
NC
NC
20 19
4
18 4IN+
NC
5
17 NC
VDD+
6
16 GND
4OUT
1
NC
2
1IN+
1OUT
3
4IN−
4OUT
20 19
4
TLV2465
FK PACKAGE
(TOP VIEW)
NC
V DD
1
20 19
9
1OUT
NC
2
1
10 11 12 13
1IN−
1OUT
3
2
TLV2464
FK PACKAGE
(TOP VIEW)
2OUT
1IN−
TLV2463
FK PACKAGE
(TOP VIEW)
3
1IN+
GND
NC
9
NC
10 11 12 13
NC
NC
9
NC
IN−
GND
4
18 NC
V DD
20 19
NC
1
NC
NC
2
18 NC
1OUT
3
NC
VDD+
2OUT
2IN−
2IN+
1IN−
NC
20 19
NC
SHDN
1
NC
NC
2
NC
NC
3
10
9
8
7
6
TLV2462
FK PACKAGE
(TOP VIEW)
4
3
2
1
20 19
1IN+
4
18 4IN+
VDD+
5
17 GND
NC
6
16 NC
7
15 3IN+
8
14 3IN−
8
14 NC
2IN+
8
14 3IN+
2IN−
3OUT
3/4SHDN
10 11 12 13
3OUT
9
NC
10 11 12 13
2SHDN
9
NC
10 11 12 13
NC
9
1/2SHDN
NC
2OUT
15 NC
3IN−
7
2OUT
NC
2IN−
15 NC
NC
7
1SHDN
NC
2IN+
NC
NC
1
2
3
4
5
NC
NC
NC
1OUT
VDD
1IN−
OUTPUT 1IN+
NC
GND
TLV2461
FK PACKAGE
(TOP VIEW)
NC
NC
TLV2460
FK PACKAGE
(TOP VIEW)
10
9
8
7
6
4IN−
1
2
3
4
5
NC
NC
IN−
IN+
GND
NC
NC
SHDN
VDD
OUTPUT
NC
1IN−
10
9
8
7
6
NC
1
2
3
4
5
NC
NC
IN−
IN+
GND
TLV2462
U PACKAGE
(TOP VIEW)
NC
TLV2460
U PACKAGE
(TOP VIEW)
NC − No internal connection
(1) SOT−23 may or may not be indicated
WWW.TI.COM
5
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V
Differential input voltage, VID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . − 0.2 V to VDD + 0.2 V
Input current, II (any input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 200 mA
Output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 175 mA
Total input current, II (into VDD +) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 mA
Total output current, IO (out of GND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 mA
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, TA: C suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
I and Q suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 125°C
M suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55°C to 125°C
Maximum junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values, except differential voltages, are with respect to GND.
DISSIPATION RATING TABLE FOR C and I SUFFIX
PACKAGE
θJC
(°C/W)
θJA
(°C/W)
TA ≤ 25°C
25 C
POWER RATING
TA < 125
125°C
C
POWER RATING
D (8)
38.3
176
710 mW
142 mW
D (14)
26.9
122.6
1022 mW
204.4 mW
D (16)
25.7
114.7
1090 mW
218 mW
DBV (5)
55
324.1
385 mW
77.1 mW
DBV (6)
55
294.3
425 mW
84.9 mW
DGK
54.2
259.9
481 mW
96.2 mW
DGS
54.1
257.7
485 mW
97 mW
N (14, 16)
32
78
1600 mW
320.5 mW
P (8)
41
104
1200 mW
240.4 mW
PW (14)
29.3
173.6
720 mW
144 mW
PW (16)
28.7
161.4
774 mW
154.9 mW
NOTE: Thermal resistances are not production tested and are for informational
purposes only.
DISSIPATION RATING TABLE FOR Q and M SUFFIX
PACKAGE
TA ≤ 25°C
25 C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C‡
TA = 70
70°C
C
POWER RATING
FK
1375 mW
11.0 mW/°C
880 mW
715 mW
275 mW
JG
1050 mW
8.4 mW/°C
672 mW
546 mW
210 mW
TA = 85
85°C
C
POWER RATING
TA = 125
125°C
C
POWER RATING
U
675 mW
5.4 mW/°C
432 mW
350 mW
135 mW
‡ This is the inverse of the traditional junction-to-ambient thermal resistance (RΘJA). Thermal resistances are not production tested and are for
informational purposes only.
6
WWW.TI.COM
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
recommended operating conditions
MIN
Single supply
Supply voltage, VDD
Split supply
2.7
6
±3
0
V
°C
C
0
VDD
70
I-suffix and Q-suffix
−40
125
M-suffix
−55
125
C-suffix
VIH
VIL
Shutdown on/off voltage level‡
UNIT
±1.35
Common-mode input voltage range, VICR
Operating free-air temperature, TA
MAX
2
0.7
V
V
‡ Relative to voltage on the GND terminal of the device.
electrical characteristics at specified free-air temperature, VDD = 3 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA†
MIN
25°C
VIO
αVIO
Input offset voltage
VDD = 3 V,
VIC = 1.5 V,
VO = 1.5 V,
RS = 50 Ω
IIB
Input bias current
TLV246xA
500
Full range
VDD = 3 V,
VIC = 1.5 V,
VO = 1.5 V,
RS = 50 Ω
2.8
Full range
20
Full range
75
25°C
4.4
Full range
25
TLV246xI/Q/M
Full range
75
High-level output voltage
VIC = 1.5 V,
IOL = 2.5 mA
Low-level output voltage
2.9
IOL = 10 mA
2.5
0.1
Full range
0.2
Full range
Full range
Short-circuit output current
0.5
AVD
Output current
Large-signal differential voltage
amplification
50
20
25°C
Sinking
Full range
Measured 1 V from rail
RL = 10 kΩ
kΩ,
VO(PP) = 1 V
40
mA
20
± 40
25°C
25°C
90
Full range
89
mA
105
ri(d)
Differential input resistance
25°C
109
† Full range is 0°C to 70°C for the C suffix, −40°C to 125°C for the I and Q suffixes, and −55°C to 125°C for the M suffix.
WWW.TI.COM
V
0.3
25°C
Sourcing
V
2.7
25°C
VIC = 1.5 V,
nA
2.8
25°C
Full range
nA
14
TLV246xC
25°C
IO
µV/°C
TLV246xI/Q/M
Full range
µV
V
7
TLV246xC
IOH = − 10 mA
IOS
1500
UNIT
1700
25°C
VOL
2000
2
IOH = − 2.5 mA
VOH
500
2200
25°C
Temperature coefficient of input offset voltage
Input offset current
MAX
Full range
25°C
IIO
TYP
dB
Ω
7
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
electrical characteristics at specified free-air temperature, VDD = 3 V (unless otherwise noted)
(continued)
PARAMETER
TEST CONDITIONS
ci(c)
Common-mode input
capacitance
f = 10 kHz
zo
Closed-loop output impedance
f = 100 kHz,
CMRR
kSVR
Common-mode rejection ratio
Supply voltage rejection ratio
((∆V
VDD //∆V
VIO)
TA†
MIN
TYP
25°C
AV = 10
25°C
25°C
66
VICR = 0 to 3 V,
RS = 50 Ω
TLV246xC
Full range
64
TLV246xI/Q/M
Full range
60
VDD = 2.7 V to 6 V,
No load
VIC = VDD /2,
VDD = 3 V to 5 V,
No load
VIC = VDD /2,
25°C
80
Full range
75
25°C
85
Full range
80
25°C
IDD
Supply current (per channels)
VO = 1.5 V,
No load
IDD(SHDN)
Supply current in shutdown
(TLV2460, TLV2463, TLV2465)
SHDN < 0.7 V,
Per channel in shutdown
MAX
7
pF
33
Ω
80
dB
85
dB
95
0.5
Full range
0.575
0.9
25°C
UNIT
0.3
Full range
2.5
mA
µA
A
† Full range is 0°C to 70°C for the C suffix, −40°C to 125°C for the I and Q suffixes, and −55°C to 125°C for the M suffix.
operating characteristics at specified free-air temperature, VDD = 3 V (unless otherwise noted)
PARAMETER
SR
Slew rate at unity gain
Vn
Equivalent input noise voltage
In
Equivalent input noise current
THD + N
t(on)
Total harmonic distortion plus
noise
Amplifier turnon time
TEST CONDITIONS
VO(PP) = 0.8 V,
RL = 10 kΩ
CL = 160 pF,
TA†
25°C
Full
range
Amplifier turnoff time
ts
φm
Settling time
1.6
16
25°C
11
f = 1 kHz
25°C
VO(PP) = 2 V,
RL = 10 kΩ, f = 1 kHz
AV = 1, RL = 10 kΩ
AV = 1
AV = 10
AV = 1, RL = 10 kΩ
Channel 1 only,
Channel 2 on
f = 10 kHz, CL = 160 pF
RL = 10 kΩ,
0.13
25°C
25
C
pA /√Hz
0.08%
7.6
25°C
7.65
µs
333
25°C
25
C
328
ns
329
25°C
5.2
V(STEP)PP = 2 V,
AV = −1, CL = 10 pF,
RL = 10 kΩ
0.1%
V(STEP)PP = 2 V,
AV = −1, CL = 56 pF,
RL = 10 kΩ
0.1%
1.77
0.01%
1.98
RL = 10 kΩ,
CL = 160 pF
WWW.TI.COM
nV/√Hz
0.02%
MHz
1.47
0.01%
1.78
25°C
25°C
44°
25°C
7
† Full range is 0°C to 70°C for the C suffix, −40°C to 125°C for the I and Q suffixes, and −55°C to 125°C for the M suffix.
8
UNIT
0.006%
AV = 100
Both channels
Channel 1 only,
Channel 2 on
MAX
V/µs
0.8
25°C
Phase margin at unity gain
Gain margin
0.9
f = 1 kHz
Channel 2 only,
Channel 1 on
Gain-bandwidth product
TYP
f = 100 Hz
Both channels
t(off)
MIN
µss
dB
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER
VIO
αVIO
IIO
IIB
Input offset voltage
Temperature coefficient of input offset voltage
Input offset current
Input bias current
TEST CONDITIONS
TA†
25°C
MIN
VDD = 5 V,
VIC = 2.5,
VO = 2.5 V,
RS = 50 Ω
25°C
TLV246xA
VDD = 5 V,
VIC = 2.5 V,
VO = 2.5 V,
RS = 50 Ω
500
Full range
25°C
2
25°C
0.3
15
Full range
60
TLV246xC
Full range
30
TLV246xI/Q/M
Full range
60
High-level output voltage
1.3
Full range
IOL = 2.5 mA
Low-level output voltage
4.7
0.1
Full range
0.2
Short-circuit output current
0.3
Output current
VIC = 2.5 V,
VO = 1 V to 4 V
92
Full range
90
Differential input resistance
ci(c)
Common-mode input capacitance
f = 10 kHz
zo
Closed-loop output impedance
f = 100 kHz,
kSVR
± 80
25°C
ri(d)
Supply voltage rejection ratio
((∆V
VDD //∆V
VIO)
60
25°C
Large-signal differential voltage
amplification
Common-mode rejection ratio
Full range
RL = 10 kΩ,
25°C
7
pF
25°C
29
Ω
25°C
71
TLV246xC
Full range
69
TLV246xI/Q/M
Full range
60
VDD = 2.7 V to 6 V,
No load
VIC = VDD /2,
25°C
80
Full range
75
VDD = 3 V to 5 V,
No load
VIC = VDD /2,
25°C
85
Full range
80
No load,
25°C
Supply current (per channel)
VO = 2.5 V,
IDD(SHDN)
Supply current in shutdown
(TLV2460, TLV2463, TLV2465)
SHDN < 0.7 V, Per channels in
shutdown
dB
Ω
VICR = 0 V to 5 V,
RS = 50 Ω
IDD
mA
109
109
25°C
AV = 10
mA
100
Measured at 1 V from rail
AVD
CMRR
145
60
25°C
Sinking
V
0.2
Full range
Full range
nA
V
4.8
25°C
Sourcing
14
4.9
25°C
IOL = 10 mA
nA
4.8
25°C
VIC = 2.5 V,
7
Full range
Full range
µV
V
µV/°C
V/°C
TLV246xI/Q/M
25°C
VIC = 2.5 V,
1500
UNIT
1700
25°C
IO
2000
TLV246xC
IOH = − 10 mA
IOS
500
2200
25°C
VOL
MAX
Full range
IOH = − 2.5 mA
VOH
TYP
85
dB
85
dB
95
dB
0.55
Full range
25°C
Full range
0.65
1
1
3
mA
µA
A
† Full range is 0°C to 70°C for the C suffix, −40°C to 125°C for the I and Q suffixes, and −55°C to 125°C for the M suffix.
WWW.TI.COM
9
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
operating characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER
SR
Slew rate at unity gain
Vn
Equivalent input noise voltage
In
THD + N
t(on)
t(off)
TEST CONDITIONS
VO(PP) = 2 V,
RL = 10 kΩ
CL = 160 pF,
TA†
25°C
Full
range
0.9
1.6
14
f = 1 kHz
25°C
11
Equivalent input noise current
f = 100 Hz
25°C
0.13
Total harmonic distortion plus noise
VO(PP) = 4 V,
RL = 10 kΩ,
f = 10 kHz
Amplifier turnon time
Amplifier turnoff time
AV = 1, RL = 10 kΩ
AV = 1, RL = 10 kΩ
AV = 1
AV = 10
Settling time
Gain margin
7.6
25°C
25
C
7.65
Both channels
333
25
C
25°C
328
f = 10 kHz,
CL = 160 pF
RL = 10 kΩ,
V(STEP)PP = 2 V,
AV = −1,
CL = 10 pF,
RL = 10 kΩ
0.1%
V(STEP)PP = 2 V,
AV = −1,
CL = 56 pF,
RL = 10 kΩ
0.1%
3.13
0.01%
3.33
RL = 10 kΩ,
CL = 160 pF
WWW.TI.COM
µs
ns
329
25°C
6.4
MHz
1.53
0.01%
1.83
µss
25°C
25°C
45°
25°C
7
† Full range is 0°C to 70°C for the C suffix, −40°C to 125°C for the I and Q suffixes, and −55°C to 125°C for the M suffix.
10
pA /√Hz
0.04%
7.25
Phase margin at unity gain
nV/√Hz
0.01%
Channel 2 only,
Channel 1 on
Channel 1 only,
Channel 2 on
UNIT
0.004%
25°C
25
C
AV = 100
Both channels
Channel 1 only,
Channel 2 on
MAX
V/µs
0.8
25°C
Gain-bandwidth product
φm
TYP
f = 100 Hz
Channel 2 only,
Channel 1 on
ts
MIN
dB
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
VIO
IIB
Input offset voltage
vs Common-mode input voltage
1, 2
Input bias current
vs Free-air temperature
3, 4
IIO
VOH
Input offset current
vs Free-air temperature
3, 4
High-level output voltage
vs High-level output current
5, 6
VOL
VO(PP)
Low-level output voltage
vs Low-level output current
7, 8
Peak-to-peak output voltage
vs Frequency
9, 10
Open-loop gain
vs Frequency
11, 12
Phase
vs Frequency
11, 12
Differential voltage amplification
vs Load resistance
13
Capacitive load
vs Load resistance
14
Zo
CMRR
Output impedance
vs Frequency
15, 16
Common-mode rejection ratio
vs Frequency
17
kSVR
Supply-voltage rejection ratio
vs Frequency
18, 19
AVD
IDD
Supply current
vs Supply voltage
20
vs Free-air temperature
21
Amplifier turnon characteristics
22
Amplifier turnoff characteristics
23
Supply current turnon
24
Supply current turnoff
SR
25
Shutdown supply current
vs Free-air temperature
Slew rate
vs Supply voltage
26
27
vs Frequency
28, 29
vs Common-mode input voltage
30, 31
Vn
Equivalent input noise voltage
THD
Total harmonic distortion
vs Frequency
32, 33
THD+N
Total harmonic distortion plus noise
vs Peak-to-peak signal amplitude
34, 35
vs Frequency
11, 12
φm
Phase margin
vs Load capacitance
36
vs Free-air temperature
37
vs Supply voltage
38
vs Free-air temperature
39
Gain bandwidth product
Large signal follower
40, 41
Small signal follower
42, 43
Inverting large signal
44, 45
Inverting small signal
46, 47
WWW.TI.COM
11
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
TYPICAL CHARACTERISTICS
INPUT OFFSET VOLTAGE
vs
COMMON-MODE INPUT VOLTAGE
INPUT OFFSET VOLTAGE
vs
COMMON-MODE INPUT VOLTAGE
1
0.6
0.4
0.2
0
−0.2
−0.4
−0.6
−0.8
−1
0
VDD = 5 V
TA = 25°C
0.8
VIO − Input Offset Voltage − mV
VIO − Input Offset Voltage − mV
0.8
1
VDD = 3 V
TA = 25°C
0.6
0.4
0.2
0
−0.2
−0.4
−0.6
−0.8
0.5
1
1.5
2
2.5
−1
3
0
VICR − Common-Mode Input Voltage − V
1
Figure 1
VDD = 3 V
VI = 1.5 V
4.5
IIB
4
3.5
3
2.5
2
1.5
1
0.5
IIO
−15
5
25
45
65
85
105
125
TA − Free-Air Temperature − °C
5
6
VDD = 5 V
VI = 2.5 V
5
IIB
4
3
2
1
IIO
0
−1
−55 −35
−15
5
25
45
65
85
TA − Free-Air Temperature − °C
Figure 3
12
4
INPUT BIAS AND INPUT OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
I IB and I IO − Input Bias and Input Offset Current − nA
I IB and I IO − Input Bias and Input Offset Current − nA
5
−0.5
−55 −35
3
Figure 2
INPUT BIAS AND INPUT OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
0
2
VICR − Common-Mode Input Voltage − V
Figure 4
WWW.TI.COM
105
125
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
TYPICAL CHARACTERISTICS
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
3
5
VDD = 5 VDC
4.5
2.5
VOH − High-Level Output Voltage − V
VOH − High-Level Output Voltage − V
VDD = 3 VDC
TA = −55°C
2
1.5
TA = 125°C
TA = 85°C
TA = 25°C
1
TA = −40°C
0.5
TA = −55°C
4
3.5
3
2.5
2
TA = 125°C
TA = 85°C
TA = 25°C
1.5
TA = −40°C
1
0.5
0
0
10
20
30
40
50
60
70
0
80
0
IOH − High-Level Output Current − mA
20
40
60
Figure 5
100 120 140 160 180 200
Figure 6
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
3
4.5
VDD = 3 VDC
VDD = 5 VDC
4
2.5
VOL − Low-Level Output Voltage − V
VOL − Low-Level Output Voltage − V
80
IOH − High-Level Output Current − mA
TA = −40°C
2
TA = 25°C
1.5
TA = 85°C
TA = 125°C
1
0.5
0
10
20
30
40
50
60
TA = −40°C
3
TA = 25°C
2.5
TA = 85°C
TA = 125°C
2
1.5
1
TA = −55°C
0.5
TA = −55°C
0
3.5
70
IOL − Low-Level Output Current − mA
0
0
20
40
60
80
100
120
140
160
IOL − Low-Level Output Current − mA
Figure 7
Figure 8
WWW.TI.COM
13
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
TYPICAL CHARACTERISTICS
PEAK-TO-PEAK OUTPUT VOLTAGE
vs
FREQUENCY
PEAK-TO-PEAK OUTPUT VOLTAGE
vs
FREQUENCY
5.5
VDD = 3 V
AV = −10
THD = 1%
RL = 10 kΩ
2.5
VO(PP) − Peak-to-Peak Output Voltage − V
VO(PP) − Peak-to-Peak Output Voltage − V
3
2
1.5
1
0.5
0
10k
100k
1M
VDD = 5 V
AV = −10
THD = 1%
RL = 10 kΩ
5
4.5
4
3.5
3
2.5
2
1.5
1
0.5
0
10k
10M
100k
f − Frequency − Hz
1M
f − Frequency − Hz
Figure 9
Figure 10
OPEN-LOOP GAIN AND PHASE
vs
FREQUENCY
100
VDD = ±1.5 V
RL = 10 kΩ
CL = 0
TA = 25°C
90
80
60
0°
−20°
−40°
AVD
50
−60°
40
−80°
−100°
30
Phase
20
−120°
10
−140°
0
−160°
−10
−180°
−20
10
100
1k
10k
100k
f − Frequency − Hz
Figure 11
14
20°
WWW.TI.COM
1M
−200°
10M
Phase
Open-Loop Gain − dB
70
40°
10M
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
TYPICAL CHARACTERISTICS
OPEN-LOOP GAIN AND PHASE
vs
FREQUENCY
100
VDD = ±2.5 V
RL = 10 kΩ
CL = 0
TA = 25°C
90
80
60
20°
0°
−20°
−40°
AVD
50
−60°
40
−80°
−100°
30
Phase
20
−120°
10
−140°
0
−160°
−10
−20
10
Phase
Open-Loop Gain − dB
70
40°
−180°
100
1k
100k
10k
1M
−200°
10M
f − Frequency − Hz
Figure 12
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
LOAD RESISTANCE
CAPACITIVE LOAD
vs
LOAD RESISTANCE
10000
TA = 25°C
160
140
CL − Capacitive Load − pF
A VD − Differential Voltage Amplification − V/mV
180
120
VDD = ±2.5 V
100
VDD = ±1.5 V
80
60
40
Phase Margin < 30°
1000
Phase Margin > 30°
VDD = 5 V
Phase Margin = 30°
TA = 25°C
20
0
100
1k
10k
100k
1M
RL − Load Resistance − Ω
100
10
100
1k
10k
RL − Load Resistance − Ω
Figure 14
Figure 13
WWW.TI.COM
15
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
TYPICAL CHARACTERISTICS
OUTPUT IMPEDANCE
vs
FREQUENCY
1000
OUTPUT IMPEDANCE
vs
FREQUENCY
1000
VDD = ±1.5 V
TA = 25°C
100
Zo − Output Impedance − Ω
Zo − Output Impedance − Ω
100
10
AV = 100
1
AV = 10
0.1
VDD = ±2.5 V
TA = 25°C
AV = 1
10
AV = 100
1
AV = 10
0.1
AV = 1
0.01
100
1k
10k
100k
1M
0.01
100
10M
1k
f − Frequency − Hz
10k
Figure 15
Figure 16
COMMON-MODE REJECTION RATIO
vs
FREQUENCY
CMRR − Common-Mode Rejection Ratio − dB
90
85
80
VDD = 5 V
VIC = 2.5 V
75
VDD = 3 V
VIC = 1.5 V
70
65
60
10
100
1k
10k
100k
f − Frequency − Hz
Figure 17
16
100k
f − Frequency − Hz
WWW.TI.COM
1M
10M
1M
10M
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
TYPICAL CHARACTERISTICS
SUPPLY-VOLTAGE REJECTION RATIO
vs
FREQUENCY
SUPPLY-VOLTAGE REJECTION RATIO
vs
FREQUENCY
90
+kSVR
VDD = ±1.5 V
TA = 25°C
100
k SVR − Supply Voltage Rejection Ratio − dB
k SVR − Supply Voltage Rejection Ratio − dB
110
90
−kSVR
80
70
60
+kSVR
50
−kSVR
40
10
100
1k
10k
100k
1M
+kSVR
80
−kSVR
70
60
+kSVR
50
−kSVR
40
10
10M
VDD = ±2.5 V
TA = 25°C
100
1k
f − Frequency − Hz
10k
100k
1M
10M
f − Frequency − Hz
Figure 18
Figure 19
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
0.8
0.80
IDD = 125°C
I DD − Supply Current − mA
I DD − Supply Current − mA
0.75
IDD = 85°C
0.7
0.6
0.5
0.40
IDD = 25°C
0.30
IDD = −55°C
VDD = 5 V
VI = 2.5 V
0.65
0.60
0.55
VDD = 3 V
VI = 1.5 V
0.50
0.45
0.40
IDD = −40°C
0.20
0.70
0.35
0.10
2.5
3
3.5
4
4.5
5
5.5
6
VDD − Supply Voltage − V
0.30
−55 −35
−15
5
25
45
65
85
105
125
TA − Free-Air Temperature − °C
Figure 20
Figure 21
WWW.TI.COM
17
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
TYPICAL CHARACTERISTICS
AMPLIFIER WITH A SHUTDOWN PULSE
TURNON CHARACTERISTICS
AMPLIFIER WITH A SHUTDOWN PULSE
TURNOFF CHARACTERISTICS
5
5
4
Shutdown Pin
3
2
1
0
Amplifier Output
3
2
1
0
−5
VDD = 5 V
RL = 10 kΩ
AV = 1
TA = 25°C
Shutdown Pin
3
VSD − Shutdown Voltage − V
VSD − Shutdown Voltage − V
4
VDD = 5 V
RL = 10 kΩ
AV = 1
TA = 25°C
−3
−1
2
1
0
Amplifier Output
3
2
1
1
3
5
9
7
0
−5
11
−3
−1
t − Time − µs
1
t − Time − µs
Figure 23
Figure 22
SUPPLY CURRENT WITH A SHUTDOWN PULSE
TURNON CHARACTERISTICS
1
5.5
0.8
4.5
0.6
3.5
Supply Current
0.4
2.5
0.2
1.5
VDD = 5 V
VI = 2.5 V
AV = 1
TA = 25°C
0
−0.2
−0.4
−0.2
0
0.2
t − Time − µs
Figure 24
18
WWW.TI.COM
0.4
0.5
−0.5
0.6
VSD − Shutdown Voltage − V
I DD − Supply Current − mA
Shutdown Pin
3
5
7
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
TYPICAL CHARACTERISTICS
TURNOFF SUPPLY CURRENT
WITH A SHUTDOWN PULSE
1
5.5
4.5
0.6
0.4
3.5
Supply Current
2.5
0.2
1.5
0
0.5
−0.2
−0.4
−0.2
0
0.2
VSD − Shutdown Voltage − V
Shutdown Pin
0.8
I DD − Supply Current − mA
VDD = 5 V
VI = 2.5 V
AV = 1
TA = 25°C
−0.5
0.6
0.4
t − Time − µs
Figure 25
SLEW RATE
vs
SUPPLY VOLTAGE
3
1.8
2.5
1.75
1.7
VDD = 5 V
VI = 2.5 V
2
SR − Slew Rate − V/ µs
I DD − Shutdown Supply Current − µ A
SHUTDOWN SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
1.5
1
VDD = 3 V
VI = 1.5 V
0.5
0
SR+
1.65
1.6
1.55
1.5
1.45
1.4
−0.5
−1
−55 −35
1.35
−15
5
25
45
65
85
105
125
TA − Free-Air Temperature − °C
SR−
1.3
2.5
VO(PP) = 2 V
CL = 160 pF
AV = 1
RL = 10 kΩ
TA = 25°C
3
3.5
4
4.5
5
5.5
6
VDD − Supply Voltage − V
Figure 27
Figure 26
WWW.TI.COM
19
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
TYPICAL CHARACTERISTICS
EQUIVALENT INPUT NOISE VOLTAGE
vs
FREQUENCY
EQUIVALENT INPUT NOISE VOLTAGE
vs
FREQUENCY
18
VDD = 3 V
AV = 10
VI = 1.5 V
TA = 25°C
17
Vn − Equivalent Input Noise Voltage − nV/ Hz
Vn − Equivalent Input Noise Voltage − nV/ Hz
18
16
15
14
13
12
11
10
100
1k
10k
VDD = 5 V
AV = 10
VI = 2.5 V
TA = 25°C
17
16
15
14
13
12
11
10
100
100k
1k
f − Frequency − Hz
Figure 28
EQUIVALENT INPUT NOISE VOLTAGE
vs
COMMON-MODE INPUT VOLTAGE
20
20
VDD = 3 V
AV = 10
f = 1 kHz
TA = 25°C
15
Vn − Equivalent Input Noise Voltage − nV/ Hz
Vn − Equivalent Input Noise Voltage − nV/ Hz
100k
Figure 29
EQUIVALENT INPUT NOISE VOLTAGE
vs
COMMON-MODE INPUT VOLTAGE
14
13
12
11
10
0
0.5
1
1.5
2
2.5
3
VICR − Common-Mode Input Voltage − V
VDD = 5 V
AV = 10
f = 1 kHz
TA = 25°C
15
14
13
12
11
10
0
1
2
3
4
VICR − Common-Mode Input Voltage − V
Figure 30
20
10k
f − Frequency − Hz
Figure 31
WWW.TI.COM
5
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
TYPICAL CHARACTERISTICS
TOTAL HARMONIC DISTORTION
vs
FREQUENCY
1
VDD = ±1.5 V
VO(PP) = 2 V
RL = 10 kΩ
THD − Total Harmonic Distortion − %
THD − Total Harmonic Distortion − %
0.5
TOTAL HARMONIC DISTORTION
vs
FREQUENCY
AV = 100
0.1
AV = 10
0.010
0.001
AV = 1
10
100
1k
10k
0.1
AV = 100
AV = 10
0.010
AV = 1
0.001
100k
VDD = ±2.5 V
VO(PP) = 4 V
RL = 10 kΩ
10
100
1k
f − Frequency − Hz
Figure 32
THD+N − Total Harmonic Distortion + Noise − %
THD+N − Total Harmonic Distortion + Noise − %
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
PEAK-TO-PEAK SIGNAL AMPLITUDE
1
RL = 250 Ω
RL = 2 kΩ
0.1
RL = 10 kΩ
0.010
RL = 100 kΩ
0.001
1
1.2 1.4 1.6 1.8 2
100k
Figure 33
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
PEAK-TO-PEAK SIGNAL AMPLITUDE
VDD = 3 V
AV = 1
TA = 25°C
10k
f − Frequency − Hz
2.2 2.4 2.6 2.8
3
3.2
Peak-to-Peak Signal Amplitude − V
1
RL = 250 Ω
RL = 2 kΩ
0.1
RL = 10 kΩ
0.010
RL = 100 kΩ
VDD = 5 V
AV = 1
TA = 25°C
0.001
4
4.1 4.2
4.3
4.4
4.5 4.6
4.7 4.8 4.9
5
Peak-to-Peak Signal Amplitude − V
Figure 34
Figure 35
WWW.TI.COM
21
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
TYPICAL CHARACTERISTICS
PHASE MARGIN
vs
LOAD CAPACITANCE
PHASE MARGIN
vs
FREE-AIR TEMPERATURE
90
80
RL = 10 kΩ
CL = 160 pF
55
70
φ m − Phase Margin − degrees
φ m − Phase Margin − degrees
60
VDD = ±2.5 V
TA = 25°C
RL = 10 kΩ
Rnull = 50 Ω
60
50
40
Rnull = 20 Ω
30
20
Rnull = 0 Ω
50
VDD = ±2.5 V
45
VDD = ±1.5 V
40
35
10
0
100
10
1k
30
−55 −35
100k
10k
CL − Load Capacitance − pF
−15
Figure 36
45
65
85
105
125
GAIN BANDWIDTH PRODUCT
vs
FREE-AIR TEMPERATURE
5
5
CL = 160 pF
RL = 10 kΩ
f = 10 kHz
TA = 25°C
4.75
Gain Bandwidth Product − MHz
Gain Bandwidth Product − MHz
25
Figure 37
GAIN BANDWIDTH PRODUCT
vs
SUPPLY VOLTAGE
4.75
5
TA − Free-Air Temperature − °C
4.5
4.25
4
3.75
4.5
RL = 10 kΩ
CL = 160 pF
VDD = ±2.5 V
4.25
4
3.75
3.5
VDD = ±1.5 V
3.25
3.5
2.5
3
3.5
4
4.5
5
5.5
6
VDD − Supply Voltage − V
−15
5
25
45
65
85
TA − Free-Air Temperature − °C
Figure 38
22
3
−55 −35
Figure 39
WWW.TI.COM
105
125
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
TYPICAL CHARACTERISTICS
LARGE SIGNAL FOLLOWER
LARGE SIGNAL FOLLOWER
2.2
3.7
2
3.3
VO − Voltage − V
Input
VO − Voltage − V
Input
1.8
Output
1.6
1.4
VDD = 3 V
VI(PP) = 1 V
VI = 1.5 V
RL = 10 kΩ
CL = 160 pF
AV = 1
TA = 25°C
1.2
1
0.8
−2
0
2
4
6
Input
2.9
Output
2.5
VDD = 5 V
VI(PP) = 2 V
VI = 2.5 V
RL = 10 kΩ
CL = 160 pF
AV = 1
TA = 25°C
2.1
Output
1.7
8
10
12
14
16
1.3
−2
18
0
2
4
6
t − Time − µs
8
10
12
14
16
18
Figure 41
SMALL SIGNAL FOLLOWER
SMALL SIGNAL FOLLOWER
1.6
2.6
1.55
2.55
VO − Voltage − V
VO − Voltage − V
Output
t − Time − µs
Figure 40
Input
1.5
Output
1.45
1.4
−0.2
Input
Input
2.5
Output
2.45
VDD = 3 V
VI(PP) = 100 mV CL = 160 pF
AV = 1
VI = 1.5 V
TA = 25°C
RL = 10 kΩ
0
0.2
0.4
0.6
0.8
1
1.2 1.4
1.6 1.8
t − Time − µs
2.4
−0.2
VDD = 5 V
VI(PP) = 100 mV
VI = 2.5 V
RL = 10 kΩ
0
0.2
0.4
0.6
CL = 160 pF
AV = 1
TA = 25°C
0.8
1
1.2 1.4
1.6 1.8
t − Time − µs
Figure 42
Figure 43
WWW.TI.COM
23
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
TYPICAL CHARACTERISTICS
INVERTING LARGE SIGNAL
INVERTING LARGE SIGNAL
4
2.3
Input
2.1
Input
3.5
VDD = 3 V
VI(PP) = 1 V
VI = 1.5 V
RL = 10 kΩ
CL = 160 pF
AV = −1
TA = 25°C
1.7
1.5
1.3
VO − Voltage − V
VO − Voltage − V
1.9
1.1
VDD = 5 V
VI(PP) = 2 V
VI = 2.5 V
RL = 10 kΩ
CL = 160 pF
AV = −1
TA = 25°C
3
2.5
2
Output
0.9
Output
1.5
0.7
0.5
−0.2
0
0.2
0.4
0.6
0.8
1
1.2 1.4
1
−0.2
1.6 1.8
0
0.2
0.4
t − Time − µs
0.6
Figure 44
1.6 1.8
2.6
Input
Input
1.55
2.55
VDD = 3 V
VI(PP) = 100 mV
VI = 1.5 V
RL = 10 kΩ
CL = 160 pF
AV = −1
TA = 25°C
1.5
VO − Voltage − V
VO − Voltage − V
1.2 1.4
INVERTING SMALL SIGNAL
1.6
1.45
VDD = 5 V
VI(PP) = 100 mV
VI = 2.5 V
RL = 10 kΩ
CL = 160 pF
AV = −1
TA = 25°C
2.5
2.45
Output
0
0.2
0.4
0.6
0.8
Output
1
1.2 1.4
1.6 1.8
t − Time − µs
2.4
−0.2
0
0.2
0.4
0.6
0.8
1
t − Time − µs
Figure 46
24
1
Figure 45
INVERTING SMALL SIGNAL
1.4
−0.2
0.8
t − Time − µs
Figure 47
WWW.TI.COM
1.2 1.4
1.6 1.8
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
PARAMETER MEASUREMENT INFORMATION
Rnull
_
+
RL
CL
Figure 48
APPLICATION INFORMATION
driving a capacitive load
When the amplifier is configured in this manner, capacitive loading directly on the output will decrease the
device’s phase margin leading to high frequency ringing or oscillations. Therefore, for capacitive loads of greater
than 10 pF, it is recommended that a resistor be placed in series (RNULL) with the output of the amplifier, as
shown in Figure 49. A minimum value of 20 Ω should work well for most applications.
RF
RG
RNULL
_
Input
Output
+
CLOAD
Figure 49. Driving a Capacitive Load
offset voltage
The output offset voltage, (VOO) is the sum of the input offset voltage (VIO) and both input bias currents (IIB) times
the corresponding gains. The following schematic and formula can be used to calculate the output offset
voltage:
RF
IIB−
RG
+
−
VI
IIB+
V
OO
+V
IO
ǒ ǒ ǓǓ
1)
R
R
F
G
VO
+
RS
"I
IB)
R
S
ǒ ǒ ǓǓ
1)
R
R
F
G
"I
IB–
R
F
Figure 50. Output Offset Voltage Model
WWW.TI.COM
25
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
APPLICATION INFORMATION
general configurations
When receiving low-level signals, limiting the bandwidth of the incoming signals into the system is often
required. The simplest way to accomplish this is to place an RC filter at the noninverting terminal of the amplifier
(see Figure 51).
RG
RF
−
VO
+
VI
R1
C1
f
V
O +
V
I
ǒ
1)
R
R
F
G
–3dB
Ǔǒ
+
1
2pR1C1
Ǔ
1
1 ) sR1C1
Figure 51. Single-Pole Low-Pass Filter
If even more attenuation is needed, a multiple pole filter is required. The Sallen-Key filter can be used for this
task. For best results, the amplifier should have a bandwidth that is 8 to 10 times the filter frequency bandwidth.
Failure to do this can result in phase shift of the amplifier.
C1
+
_
VI
R1
R1 = R2 = R
C1 = C2 = C
Q = Peaking Factor
(Butterworth Q = 0.707)
R2
f
C2
RG
RF
RG =
Figure 52. 2-Pole Low-Pass Sallen-Key Filter
26
WWW.TI.COM
–3dB
+
(
1
2pRC
RF
1
2−
Q
)
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
APPLICATION INFORMATION
shutdown function
Three members of the TLV246x family (TLV2460/3/5) have a shutdown terminal for conserving battery life in
portable applications. When the shutdown terminal is tied low, the supply current is reduced to 0.3 µA/channel,
the amplifier is disabled, and the outputs are placed in a high impedance mode. To enable the amplifier, the
shutdown terminal can either be left floating or pulled high. When the shutdown terminal is left floating, care
should be taken to ensure that parasitic leakage current at the shutdown terminal does not inadvertently place
the operational amplifier into shutdown. The shutdown terminal threshold is always referenced to VDD/2.
Therefore, when operating the device with split supply voltages (e.g. ± 2.5 V), the shutdown terminal needs to
be pulled to VDD− (not GND) to disable the operational amplifier.
The amplifier’s output with a shutdown pulse is shown in Figures 22, 23, 24, and 25. The amplifier is powered
with a single 5-V supply and configured as a noninverting configuration with a gain of 5. The amplifier turnon
and turnoff times are measured from the 50% point of the shutdown pulse to the 50% point of the output
waveform. The times for the single, dual, and quad are listed in the data tables.
circuit layout considerations
To achieve the levels of high performance of the TLV246x, follow proper printed-circuit board design techniques.
A general set of guidelines is given in the following.
D Ground planes − It is highly recommended that a ground plane be used on the board to provide all
components with a low inductive ground connection. However, in the areas of the amplifier inputs and
output, the ground plane can be removed to minimize the stray capacitance.
D Proper power supply decoupling − Use a 6.8-µF tantalum capacitor in parallel with a 0.1-µF ceramic
capacitor on each supply terminal. It may be possible to share the tantalum among several amplifiers
depending on the application, but a 0.1-µF ceramic capacitor should always be used on the supply terminal
of every amplifier. In addition, the 0.1-µF capacitor should be placed as close as possible to the supply
terminal. As this distance increases, the inductance in the connecting trace makes the capacitor less
effective. The designer should strive for distances of less than 0.1 inches between the device power
terminals and the ceramic capacitors.
D Sockets − Sockets can be used but are not recommended. The additional lead inductance in the socket pins
will often lead to stability problems. Surface-mount packages soldered directly to the printed-circuit board
is the best implementation.
D Short trace runs/compact part placements − Optimum high performance is achieved when stray series
inductance has been minimized. To realize this, the circuit layout should be made as compact as possible,
thereby minimizing the length of all trace runs. Particular attention should be paid to the inverting input of
the amplifier. Its length should be kept as short as possible. This will help to minimize stray capacitance at
the input of the amplifier.
D Surface-mount passive components − Using surface-mount passive components is recommended for high
performance amplifier circuits for several reasons. First, because of the extremely low lead inductance of
surface-mount components, the problem with stray series inductance is greatly reduced. Second, the small
size of surface-mount components naturally leads to a more compact layout thereby minimizing both stray
inductance and capacitance. If leaded components are used, it is recommended that the lead lengths be
kept as short as possible.
WWW.TI.COM
27
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
APPLICATION INFORMATION
general power dissipation considerations
For a given θJA, the maximum power dissipation is shown in Figure 53 and is calculated by the following formula:
P
D
+
Where:
ǒ
T
Ǔ
–T
MAX A
q
JA
PD = Maximum power dissipation of THS246x IC (watts)
TMAX = Absolute maximum junction temperature (150°C)
TA
= Free-ambient air temperature (°C)
θJA = θJC + θCA
θJC = Thermal coefficient from junction to case
θCA = Thermal coefficient from case to ambient air (°C/W)
MAXIMUM POWER DISSIPATION
vs
FREE-AIR TEMPERATURE
2
Maximum Power Dissipation − W
1.75
PDIP Package
Low-K Test PCB
θJA = 104°C/W
1.5
1.25
TJ = 150°C
MSOP Package
Low-K Test PCB
θJA = 260°C/W
SOIC Package
Low-K Test PCB
θJA = 176°C/W
1
0.75
0.5
0.25
SOT-23 Package
Low-K Test PCB
θJA = 324°C/W
0
−55 −40 −25 −10 5
20 35 50 65 80 95 110 125
TA − Free-Air Temperature − °C
NOTE A: Results are with no air flow and using JEDEC Standard Low-K test PCB.
Figure 53. Maximum Power Dissipation vs Free-Air Temperature
28
WWW.TI.COM
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
APPLICATION INFORMATION
macromodel information
Macromodel information provided was derived using Microsim Parts Release 8, the model generation
software used with Microsim PSpice . The Boyle macromodel (see Note 2) and subcircuit in Figure 54 are
generated using the TLV246x typical electrical and operating characteristics at TA = 25°C. Using this
information, output simulations of the following key parameters can be generated to a tolerance of 20% (in most
cases):
D
D
D
D
D
D
D
D
D
D
D
D
Maximum positive output voltage swing
Maximum negative output voltage swing
Slew rate
Quiescent power dissipation
Input bias current
Open-loop voltage amplification
Unity-gain frequency
Common-mode rejection ratio
Phase margin
DC output resistance
AC output resistance
Short-circuit output current limit
NOTE 2: G. R. Boyle, B. M. Cohn, D. O. Pederson, and J. E. Solomon, “Macromodeling of Intergrated Circuit Operational Amplifiers”, IEEE
Journal of Solid-State Circuits, SC-9, 353 (1974).
99
EGND +
R2
3
VDD +
−
+
ISS
RSS
CSS
VD
−
53
RP
10
2
IN −
J1
FB
6
7
+
9
VLIM
+
VB
8
GA
GCM
J2
−
−
DC
RO1
OUT
IN +
1
11
12
RD1
92
54
+
RD2
VE
+ DLP
91
+
VLP
−
−
−
+
90
HLIM
−
4
5
DLN
DE
C1
DP
GND
RO2
C2
VLN
RD1
3
11
2.8964E3
RD2
3
12
2.8964E3
R01
8
5
5.6000
R02
7
99
6.2000
RP
3
4
8.9127
RSS
10
99
10.610E6
VB
9
0
DC 0
VC
3
53
DC .7836
VE
54
4
DC .7436
VLIM
7
8
DC 0
VLP
91
0
DC 117
VLN
0
92
DC 117
.MODEL DX D (IS=800.00E−18)
.MODEL DY D (IS=800.00E−18 Rs = 1m Cjo=10p)
.MODEL JX1 NJF (IS=1.0000E−12 BETA=6.3239E−3
+ VTO= −1)
.MODEL JX2 NJF (IS=1.0000E−12 BETA=6.3239E−3
+ VTO= −1)
.ENDS
.SUBCKT TLV246X 1 2 3 4 5
C1
11
12
2.46034E−12
C2
6
7
10.0000E−12
CSS
10
99
443.21E−15
DC
5
53
DY
DE
54
5
DY
DLP
90
91
DX
DLN
92
90
DX
DP
4
3
DX
EGND
99
0
POLY (2) (3,0) (4,0) 0 .5 .5
FB
7
99
POLY (5) VB VC VE VLP
+ VLN 0 21.600E6 −1E3 1E3 22E6 −22E6
GA
6
0
11
12 345.26E−6
GCM
0
6
10
99 15.4226E−9
ISS
10
4
DC 18.850E−6
HLIM
90
0
VLIM 1K
J1
11
2
10 JX1
J2
12
1
10 JX2
R2
6
9
100.00E3
Figure 54. Boyle Macromodels and Subcircuit
PSpice and Parts are trademarks of MicroSim Corporation.
WWW.TI.COM
29
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
macromodel information (continued)
rp
3
71
8.9127
rss
10
99
10.610E6
rs1
6
4
1G
rs2
6
4
1G
rs3
6
4
1G
rs4
6
4
1G
s1
71
4
6 4 s1x
s2
70
5
6 4 s1x
s3
10
74
6 4 s1x
s4
74
4
6 4 s2x
vb
9
0
dc 0
vc
3
53
dc .7836
ve
54
4
dc .7436
vlim
7
8
dc 0
vlp
91
0
dc 117
vln
0
92
dc 117
.model dx D(Is=800.00E−18)
.model dy D(Is=800.00E−18 Rs=1m Cjo=10p)
.model jx1 NJF(Is=1.0000E−12 Beta=6.3239E−3 Vto=−1)
.model jx2 NJF(Is=1.0000E−12 Beta=6.3239E−3 Vto=−1)
.model s1x VSWITCH(Roff=1E8 Ron=1.0 Voff=2.5 Von=0.0)
.model s2x VSWITCH(Roff=1E8 Ron=1.0 Voff=0 Von=2.5)
.ends
.subckt TLV_246Y 1 2 3 4 5 6
c1
11
12
2.4603E−12
c2
72
7
10.000E−12
css
10
99
443.21E−15
dc
70
53
dy
de
54
70
dy
dlp
90
91
dx
dln
92
90
dx
dp
4
3
dx
egnd
99
0
poly(2) (3,0) (4,0) 0 .5 .5
fb
7
99
poly(5) vb vc ve vlp vln 0
21.600E6 −1E3 1E3 22E6 −22E6
ga
72
0
11 12 345.26E−6
gcm
0
72
10 99 15.422E−9
iss
74
4
dc 18.850E−6
hlim
90
0
vlim 1K
j1
11
2
10 jx1
j2
12
1
10 jx2
r2
72
9
100.00E3
rd1
3
11
2.8964E3
rd2
3
12
2.8964E3
ro1
8
70
5.6000
ro2
7
99
6.2000
Figure 54. Boyle Macromodels and Subcircuit (Continued)
30
WWW.TI.COM
PACKAGE OPTION ADDENDUM
www.ti.com
12-Jan-2006
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
Lead/Ball Finish
MSL Peak Temp (3)
5962-0051201Q2A
ACTIVE
LCCC
FK
20
1
TBD
5962-0051201QHA
ACTIVE
CFP
U
10
1
TBD
5962-0051201QPA
ACTIVE
CDIP
JG
8
1
TBD
5962-0051202Q2A
ACTIVE
LCCC
FK
20
1
TBD
5962-0051202QHA
ACTIVE
CFP
U
10
1
TBD
5962-0051202QPA
ACTIVE
CDIP
JG
8
1
TBD
5962-0051203Q2A
ACTIVE
LCCC
FK
20
1
TBD
5962-0051203QHA
ACTIVE
CFP
U
10
1
TBD
5962-0051203QPA
ACTIVE
CDIP
JG
8
1
TBD
5962-0051204Q2A
ACTIVE
LCCC
FK
20
1
TBD
5962-0051204QHA
ACTIVE
CFP
U
10
1
TBD
5962-0051204QPA
ACTIVE
CDIP
JG
8
1
TBD
5962-0051205Q2A
ACTIVE
LCCC
FK
20
1
TBD
5962-0051205QHA
ACTIVE
CFP
U
10
1
TBD
5962-0051205QPA
ACTIVE
CDIP
JG
8
1
TBD
5962-0051206Q2A
ACTIVE
LCCC
FK
20
1
TBD
5962-0051206QHA
ACTIVE
CFP
U
10
1
TBD
A42 SNPB
N / A for Pkg Type
5962-0051206QPA
ACTIVE
CDIP
JG
8
1
TBD
A42 SNPB
N / A for Pkg Type
5962-0051207Q2A
ACTIVE
LCCC
FK
20
1
TBD
5962-0051207QCA
ACTIVE
CDIP
J
14
1
TBD
5962-0051208Q2A
ACTIVE
LCCC
FK
20
1
TBD
5962-0051208QCA
ACTIVE
CDIP
J
14
1
TBD
TLV2460AIDR
ACTIVE
SOIC
D
8
TLV2460AIP
ACTIVE
PDIP
P
8
50
TLV2460AIPE4
ACTIVE
PDIP
P
8
TLV2460AMFKB
ACTIVE
LCCC
FK
TLV2460AMJG
ACTIVE
CDIP
JG
TLV2460AMJGB
ACTIVE
CDIP
TLV2460AMUB
ACTIVE
TLV2460AQD
ACTIVE
TLV2460AQDR
ACTIVE
2500 Green (RoHS &
no Sb/Br)
POST-PLATE N / A for Pkg Type
A42 SNPB
N / A for Pkg Type
A42 SNPB
N / A for Pkg Type
POST-PLATE N / A for Pkg Type
A42 SNPB
N / A for Pkg Type
A42 SNPB
N / A for Pkg Type
POST-PLATE N / A for Pkg Type
A42 SNPB
N / A for Pkg Type
A42 SNPB
N / A for Pkg Type
POST-PLATE N / A for Pkg Type
A42 SNPB
N / A for Pkg Type
A42 SNPB
N / A for Pkg Type
POST-PLATE N / A for Pkg Type
A42 SNPB
N / A for Pkg Type
A42 SNPB
N / A for Pkg Type
POST-PLATE N / A for Pkg Type
POST-PLATE N / A for Pkg Type
A42 SNPB
N / A for Pkg Type
POST-PLATE N / A for Pkg Type
A42 SNPB
N / A for Pkg Type
CU NIPDAU
Level-1-260C-UNLIM
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
20
1
TBD
8
1
TBD
A42 SNPB
N / A for Pkg Type
JG
8
1
TBD
A42 SNPB
N / A for Pkg Type
CFP
U
10
1
TBD
A42 SNPB
N / A for Pkg Type
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-UNLIM/
Level-1-235C-UNLIM
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-UNLIM/
Level-1-235C-UNLIM
POST-PLATE N / A for Pkg Type
TLV2460AQPW
ACTIVE
TSSOP
PW
8
150
TBD
CU NIPDAU
Level-1-220C-UNLIM
TLV2460AQPWR
ACTIVE
TSSOP
PW
8
2000
TBD
CU NIPDAU
Level-1-220C-UNLIM
TLV2460CD
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2460CDBVR
ACTIVE
SOT-23
DBV
6
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2460CDBVRG4
ACTIVE
SOT-23
DBV
6
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
12-Jan-2006
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TLV2460CDBVT
ACTIVE
SOT-23
DBV
6
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2460CDBVTG4
ACTIVE
SOT-23
DBV
6
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2460CDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2460CDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2460CP
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2460CPE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2460ID
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2460IDBVR
ACTIVE
SOT-23
DBV
6
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2460IDBVRG4
ACTIVE
SOT-23
DBV
6
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2460IDBVT
ACTIVE
SOT-23
DBV
6
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2460IDBVTG4
ACTIVE
SOT-23
DBV
6
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2460IDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2460IDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2460IP
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2460IPE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2460MFKB
ACTIVE
LCCC
FK
20
1
TBD
TLV2460MJG
ACTIVE
CDIP
JG
8
1
TBD
A42 SNPB
N / A for Pkg Type
TLV2460MJGB
ACTIVE
CDIP
JG
8
1
TBD
A42 SNPB
N / A for Pkg Type
TLV2460MUB
ACTIVE
CFP
U
10
1
TBD
A42 SNPB
N / A for Pkg Type
TLV2460QD
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-UNLIM/
Level-1-235C-UNLIM
TLV2460QDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-UNLIM/
Level-1-235C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
POST-PLATE N / A for Pkg Type
TLV2460QPW
ACTIVE
TSSOP
PW
8
150
TBD
CU NIPDAU
Level-1-220C-UNLIM
TLV2460QPWR
ACTIVE
TSSOP
PW
8
2000
TBD
CU NIPDAU
Level-1-220C-UNLIM
TLV2461AID
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2461AIDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2461AIDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2461AIP
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2461AIPE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
12-Jan-2006
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TLV2461AMFKB
ACTIVE
LCCC
FK
20
1
TBD
TLV2461AMJGB
ACTIVE
CDIP
JG
8
1
TBD
TLV2461AMUB
ACTIVE
CFP
U
10
1
TLV2461AQD
ACTIVE
SOIC
D
8
75
TLV2461AQDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
Lead/Ball Finish
MSL Peak Temp (3)
POST-PLATE N / A for Pkg Type
A42 SNPB
N / A for Pkg Type
TBD
A42 SNPB
N / A for Pkg Type
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-UNLIM/
Level-1-235C-UNLIM
CU NIPDAU
Level-2-260C-UNLIM/
Level-1-235C-UNLIM
TLV2461AQPW
ACTIVE
TSSOP
PW
8
150
TBD
Call TI
TLV2461AQPWR
ACTIVE
TSSOP
PW
8
2000
TBD
CU NIPDAU
Level-1-220C-UNLIM
TLV2461CD
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2461CDBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2461CDBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2461CDBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2461CDBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2461CDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2461CDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2461CP
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2461CPE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2461ID
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2461IDBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2461IDBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2461IDBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2461IDBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2461IDG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2461IDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2461IDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2461IP
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2461IPE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2461MFKB
ACTIVE
LCCC
FK
20
1
TBD
TLV2461MJGB
ACTIVE
CDIP
JG
8
1
TBD
A42 SNPB
N / A for Pkg Type
TLV2461MUB
ACTIVE
CFP
U
10
1
TBD
A42 SNPB
N / A for Pkg Type
Addendum-Page 3
Call TI
POST-PLATE N / A for Pkg Type
PACKAGE OPTION ADDENDUM
www.ti.com
12-Jan-2006
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TLV2461QD
ACTIVE
SOIC
D
8
TLV2461QDR
ACTIVE
SOIC
D
8
75
Lead/Ball Finish
MSL Peak Temp (3)
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-UNLIM/
Level-1-235C-UNLIM
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-UNLIM/
Level-1-235C-UNLIM
TLV2461QPW
ACTIVE
TSSOP
PW
8
150
TBD
Call TI
TLV2461QPWR
ACTIVE
TSSOP
PW
8
2000
TBD
CU NIPDAU
Level-1-220C-UNLIM
TLV2462AID
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2462AIDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2462AIDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2462AIP
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2462AIPE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2462AMFKB
ACTIVE
LCCC
FK
20
1
TBD
TLV2462AMJG
ACTIVE
CDIP
JG
8
1
TBD
A42 SNPB
N / A for Pkg Type
TLV2462AMJGB
ACTIVE
CDIP
JG
8
1
TBD
A42 SNPB
N / A for Pkg Type
TLV2462AMUB
ACTIVE
CFP
U
10
1
TBD
A42 SNPB
N / A for Pkg Type
TLV2462AQD
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-UNLIM/
Level-1-235C-UNLIM
TLV2462AQDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-UNLIM/
Level-1-235C-UNLIM
TLV2462AQPWR
ACTIVE
TSSOP
PW
8
2000
TBD
CU NIPDAU
Level-1-220C-UNLIM
TLV2462CD
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2462CDG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2462CDGK
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2462CDGKR
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2462CDGKRG4
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2462CDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2462CDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2462CP
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2462CPE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2462ID
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2462IDG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2462IDGK
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2462IDGKR
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
CU NIPDAU
Level-1-260C-UNLIM
Addendum-Page 4
Call TI
POST-PLATE N / A for Pkg Type
PACKAGE OPTION ADDENDUM
www.ti.com
12-Jan-2006
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TLV2462IDGKRG4
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2462IDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2462IDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2462IP
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2462IPE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2462MFKB
ACTIVE
LCCC
FK
20
1
TBD
TLV2462MJG
ACTIVE
CDIP
JG
8
1
TBD
A42 SNPB
N / A for Pkg Type
TLV2462MJGB
ACTIVE
CDIP
JG
8
1
TBD
A42 SNPB
N / A for Pkg Type
TLV2462MUB
ACTIVE
CFP
U
10
1
TBD
A42 SNPB
N / A for Pkg Type
TLV2462QD
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-UNLIM/
Level-1-235C-UNLIM
TLV2462QDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-UNLIM/
Level-1-235C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
no Sb/Br)
POST-PLATE N / A for Pkg Type
TLV2462QPW
ACTIVE
TSSOP
PW
8
150
TBD
CU NIPDAU
Level-1-220C-UNLIM
TLV2462QPWR
ACTIVE
TSSOP
PW
8
2000
TBD
CU NIPDAU
Level-1-220C-UNLIM
TLV2463AID
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2463AIDG4
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2463AIDR
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2463AIDRG4
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2463AIN
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2463AINE4
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2463AMFKB
ACTIVE
LCCC
FK
20
1
TBD
TLV2463AMJ
ACTIVE
CDIP
J
14
1
TBD
A42 SNPB
N / A for Pkg Type
TLV2463AMJB
ACTIVE
CDIP
J
14
1
TBD
A42 SNPB
N / A for Pkg Type
TLV2463AQD
ACTIVE
SOIC
D
14
50
Pb-Free
(RoHS)
CU NIPDAU
Level-2-250C-1 YEAR/
Level-1-235C-UNLIM
POST-PLATE N / A for Pkg Type
TLV2463AQDR
ACTIVE
SOIC
D
14
75
TBD
CU NIPDAU
Level-1-220C-UNLIM
TLV2463AQPWR
ACTIVE
TSSOP
PW
14
2000
TBD
CU NIPD
Level-1-250C-UNLIM
TLV2463CD
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2463CDGS
ACTIVE
MSOP
DGS
10
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2463CDGSG4
ACTIVE
MSOP
DGS
10
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TLV2463CDGSR
ACTIVE
MSOP
DGS
10
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2463CDGSRG4
ACTIVE
MSOP
DGS
10
2500 Green (RoHS &
CU NIPDAU
Level-1-260C-UNLIM
Addendum-Page 5
PACKAGE OPTION ADDENDUM
www.ti.com
12-Jan-2006
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TLV2463CDR
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2463CDRG4
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2463CN
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2463CNE4
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2463ID
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2463IDGS
ACTIVE
MSOP
DGS
10
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2463IDGSR
ACTIVE
MSOP
DGS
10
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2463IDGSRG4
ACTIVE
MSOP
DGS
10
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2463IN
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2463INE4
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2463MFKB
ACTIVE
LCCC
FK
20
1
TBD
TLV2463MJ
ACTIVE
CDIP
J
14
1
TBD
TLV2463MJB
ACTIVE
CDIP
J
14
1
TLV2463QD
ACTIVE
SOIC
D
14
75
Lead/Ball Finish
MSL Peak Temp (3)
no Sb/Br)
POST-PLATE N / A for Pkg Type
A42 SNPB
N / A for Pkg Type
TBD
A42 SNPB
N / A for Pkg Type
Pb-Free
(RoHS)
CU NIPDAU
Level-2-250C-1 YEAR/
Level-1-235C-UNLIM
TLV2463QDR
ACTIVE
SOIC
D
14
75
TBD
CU NIPDAU
Level-1-220C-UNLIM
TLV2463QPWR
ACTIVE
TSSOP
PW
14
2000
TBD
CU NIPD
Level-1-250C-UNLIM
TLV2464AID
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2464AIDR
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2464AIDRG4
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2464AIN
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPD
N / A for Pkg Type
TLV2464AINE4
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPD
N / A for Pkg Type
TLV2464AIPW
ACTIVE
TSSOP
PW
14
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2464AIPWR
ACTIVE
TSSOP
PW
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2464AIPWRG4
ACTIVE
TSSOP
PW
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2464CD
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2464CDG4
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2464CDR
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Addendum-Page 6
PACKAGE OPTION ADDENDUM
www.ti.com
12-Jan-2006
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TLV2464CDRG4
ACTIVE
SOIC
D
14
TLV2464CN
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPD
N / A for Pkg Type
TLV2464CNE4
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPD
N / A for Pkg Type
TLV2464CPW
ACTIVE
TSSOP
PW
14
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2464CPWG4
ACTIVE
TSSOP
PW
14
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2464CPWR
ACTIVE
TSSOP
PW
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2464CPWRG4
ACTIVE
TSSOP
PW
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2464ID
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2464IDG4
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2464IDR
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2464IDRG4
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2464IN
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPD
N / A for Pkg Type
TLV2464INE4
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPD
N / A for Pkg Type
TLV2464IPW
ACTIVE
TSSOP
PW
14
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2464IPWG4
ACTIVE
TSSOP
PW
14
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2464IPWR
ACTIVE
TSSOP
PW
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2464IPWRG4
ACTIVE
TSSOP
PW
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2465AID
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2465AIDG4
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2465AIPWR
ACTIVE
TSSOP
PW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2465AIPWRG4
ACTIVE
TSSOP
PW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2465CD
ACTIVE
SOIC
D
16
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2465CDR
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2465CDRG4
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2465CN
ACTIVE
PDIP
N
16
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2465CNE4
ACTIVE
PDIP
N
16
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
2500 Green (RoHS &
no Sb/Br)
40
Addendum-Page 7
Lead/Ball Finish
CU NIPDAU
MSL Peak Temp (3)
Level-1-260C-UNLIM
PACKAGE OPTION ADDENDUM
www.ti.com
12-Jan-2006
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TLV2465CPW
ACTIVE
TSSOP
PW
16
TLV2465CPWR
ACTIVE
TSSOP
PW
TLV2465CPWRG4
ACTIVE
TSSOP
TLV2465ID
ACTIVE
TLV2465IDG4
90
Lead/Ball Finish
MSL Peak Temp (3)
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2465IDR
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2465IDRG4
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2465IN
ACTIVE
PDIP
N
16
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2465INE4
ACTIVE
PDIP
N
16
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2465IPW
ACTIVE
TSSOP
PW
16
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2465IPWR
ACTIVE
TSSOP
PW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2465IPWRG4
ACTIVE
TSSOP
PW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
Addendum-Page 8
PACKAGE OPTION ADDENDUM
www.ti.com
12-Jan-2006
to Customer on an annual basis.
Addendum-Page 9
MECHANICAL DATA
MCER001A – JANUARY 1995 – REVISED JANUARY 1997
JG (R-GDIP-T8)
CERAMIC DUAL-IN-LINE
0.400 (10,16)
0.355 (9,00)
8
5
0.280 (7,11)
0.245 (6,22)
1
0.063 (1,60)
0.015 (0,38)
4
0.065 (1,65)
0.045 (1,14)
0.310 (7,87)
0.290 (7,37)
0.020 (0,51) MIN
0.200 (5,08) MAX
Seating Plane
0.130 (3,30) MIN
0.023 (0,58)
0.015 (0,38)
0°–15°
0.100 (2,54)
0.014 (0,36)
0.008 (0,20)
4040107/C 08/96
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
This package can be hermetically sealed with a ceramic lid using glass frit.
Index point is provided on cap for terminal identification.
Falls within MIL STD 1835 GDIP1-T8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MCFP001A – JANUARY 1995 – REVISED DECEMBER 1995
U (S-GDFP-F10)
CERAMIC DUAL FLATPACK
Base and Seating Plane
0.250 (6,35)
0.246 (6,10)
0.045 (1,14)
0.026 (0,66)
0.008 (0,20)
0.004 (0,10)
0.080 (2,03)
0.050 (1,27)
0.300 (7,62) MAX
1
0.019 (0,48)
0.015 (0,38)
10
0.050 (1,27)
0.280 (7,11)
0.230 (5,84)
5
6
4 Places
0.005 (0,13) MIN
0.350 (8,89)
0.250 (6,35)
0.350 (8,89)
0.250 (6,35)
4040179 / B 03/95
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
This package can be hermetically sealed with a ceramic lid using glass frit.
Index point is provided on cap for terminal identification only.
Falls within MIL STD 1835 GDFP1-F10 and JEDEC MO-092AA
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MLCC006B – OCTOBER 1996
FK (S-CQCC-N**)
LEADLESS CERAMIC CHIP CARRIER
28 TERMINAL SHOWN
18
17
16
15
14
13
NO. OF
TERMINALS
**
12
19
11
20
10
A
B
MIN
MAX
MIN
MAX
20
0.342
(8,69)
0.358
(9,09)
0.307
(7,80)
0.358
(9,09)
28
0.442
(11,23)
0.458
(11,63)
0.406
(10,31)
0.458
(11,63)
21
9
22
8
44
0.640
(16,26)
0.660
(16,76)
0.495
(12,58)
0.560
(14,22)
23
7
52
0.739
(18,78)
0.761
(19,32)
0.495
(12,58)
0.560
(14,22)
24
6
68
0.938
(23,83)
0.962
(24,43)
0.850
(21,6)
0.858
(21,8)
84
1.141
(28,99)
1.165
(29,59)
1.047
(26,6)
1.063
(27,0)
B SQ
A SQ
25
5
26
27
28
1
2
3
4
0.080 (2,03)
0.064 (1,63)
0.020 (0,51)
0.010 (0,25)
0.020 (0,51)
0.010 (0,25)
0.055 (1,40)
0.045 (1,14)
0.045 (1,14)
0.035 (0,89)
0.045 (1,14)
0.035 (0,89)
0.028 (0,71)
0.022 (0,54)
0.050 (1,27)
4040140 / D 10/96
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
This package can be hermetically sealed with a metal lid.
The terminals are gold plated.
Falls within JEDEC MS-004
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MPDI001A – JANUARY 1995 – REVISED JUNE 1999
P (R-PDIP-T8)
PLASTIC DUAL-IN-LINE
0.400 (10,60)
0.355 (9,02)
8
5
0.260 (6,60)
0.240 (6,10)
1
4
0.070 (1,78) MAX
0.325 (8,26)
0.300 (7,62)
0.020 (0,51) MIN
0.015 (0,38)
Gage Plane
0.200 (5,08) MAX
Seating Plane
0.010 (0,25) NOM
0.125 (3,18) MIN
0.100 (2,54)
0.021 (0,53)
0.015 (0,38)
0.430 (10,92)
MAX
0.010 (0,25) M
4040082/D 05/98
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Mailing Address:
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2006, Texas Instruments Incorporated