TLWD1100(T11) TOSHIBA LED Lamps TLWD1100(T11) Panel Circuit Indicator • • • • • • • • • • Unit: mm Surface-mount devices 3.2 (L) × 2.8 (W) × 1.9 (H) mm LED chip + phosphor Luminous intensity : Iv = 180 mcd (typ.) @20mA Color: White Chromaticity (typ.) : Cx=0.32,Cy=0.31 Topr / Tstg = -40 to 100°C Reflow soldering is possible Applications: automotive use, backlighting etc. Standard embossed tape packing: T11 (2000/reel) 8-mm tape reel Color and Material Product Name Color Material TLWD1100 White InGaN Rating Unit IF 30 mA Power Dissipation PD 120 mW Operating Temperature Topr −40~100 °C Storage Temperature Tstg −40~100 °C (Note 1) JEITA ― 4-3R1 Weight: 0.035 g (typ.) Symbol Forward Current ― TOSHIBA Absolute Maximum Ratings (Ta = 25°C) Characteristics JEDEC Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 1: Forward current derating 30 Allowable forward current IF (mA) IF – Ta 35 25 20 15 10 5 0 0 20 40 60 80 Ambient temperature 1 Ta 100 120 (°C) 2007-10-01 TLWD1100(T11) Electrical Characteristics (Ta = 25°C) Characteristics Symbol Test condition Min. Typ. Max. Unit Forward Voltage VF IF = 20 mA 2.7 3.3 4.0 V Reverse Current IR VR = 4 V ⎯ ⎯ 10 uA Symbol Test condition Min. Typ. Max. Unit Cx IF = 20 mA (Note 2) ⎯ Cy IF = 20 mA (Note 2) ⎯ IV IF = 20 mA Optical Characteristics (Ta = 25°C) Characteristics Chromaticity Luminous Intensity (Note 3) 63 180 320 mcd Note 2: The product is tested at the following chromaticity coordinate groups. Cy Test conditions: IF=20mA, Ta=25°C Tolerance: +/-0.01 0.42 0.41 0.40 0.39 0.38 0.37 0.36 0.35 0.34 0.33 0.32 0.31 0.30 0.29 0.28 0.27 0.26 0.25 0.24 0.23 0.22 0.21 0.20 8L 7L 8K 6L 7K 5L 6K 4L 3L 5K 4K 3K 0.25 0.26 0.27 0.28 0.29 0.30 0.31 0.32 0.33 0.34 0.35 0.36 0.37 Cx 3K 3L 4K 4L Cx 0.273 0.266 0.280 0.286 0.266 0.258 0.273 0.280 0.286 0.280 0.291 0.296 0.280 0.273 0.285 0.291 Cy 0.227 0.232 0.252 0.244 0.232 0.239 0.261 0.252 0.244 0.252 0.268 0.259 0.252 0.261 0.279 0.268 5K 5L 6K 6L Cx 0.296 0.291 0.310 0.313 0.291 0.285 0.307 0.310 0.313 0.310 0.330 0.330 0.310 0.307 0.330 0.330 2 Cy 0.259 0.268 0.297 0.284 0.268 0.279 0.312 0.297 0.284 0.297 0.330 0.310 0.297 0.312 0.347 0.330 7K 7L 8K 8L Cx 0.330 0.330 0.338 0.352 0.330 0.330 0.347 0.345 0.352 0.338 0.364 0.360 0.345 0.347 0.367 0.364 Cy 0.310 0.330 0.342 0.344 0.330 0.347 0.371 0.352 0.344 0.342 0.380 0.357 0.352 0.371 0.401 0.380 2007-10-01 TLWD1100(T11) Note 3: Iv rank classification Test conditions: IF=20mA, Ta=25°C Product name Luminous intensity IV min typ max 63 180 320 QA 63 ⎯ 125 RA 100 ⎯ 200 SA 160 ⎯ 320 TLWD1100(T11) Unit mcd IF 20 mA The specification on the above table is used for Iv classification of LEDs in Toshiba facility. Each reel includes the same rank LEDs. Let the delivery ratio of each rank be unquestioned. Note 4: Caution ESD withstand voltage according to MIL STD 883D, Method 3015.7 : ≥1000V When handling this LED, take the following measures to prevent the LED from being damaged or otherwise adversely affected. 1) Use a conductive tablemat and conductive floor mat, and ground the workbench and floor. 2) Operators handling laser diodes must be grounded via a high resistance (about 1MΩ). A conductive strap is good for this purpose. 3) Ground all tools including soldering irons. This product is designed as a general display light source usage, and it has applied the measurement standard that matched with the sensitivity of human's eyes. Therefore, it is not intended for usage of functional application (ex. Light source for sensor, optical communication and etc) except general display light source. 3 2007-10-01 TLWD1100(T11) TLWD1100 IF – V F IV/IV(20 mA) – IF (typ.) (typ.) 3 100 IV/IV(20 mA) (mA) Ta = 25°C Luminous intensity Forward Current IF 30 10 3 1 2.2 2.6 3.0 3.4 3.8 Forward Voltage 4.2 VF 4.6 Ta = 25°C 1 0.3 0.1 0.03 0.01 1 5.0 3 5 10 30 Forward Current (V) Relative IV – Tc 100 300 500 IF (mA) Cx, Cy – IF (typ.) 10 50 (typ.) 0.34 Relative luminous Intensity IV Ta = 25°C Chromaticity Cx, Cy 0.33 1 Cx 0.32 0.31 Cy 0.3 0.1 0.29 -40 -20 0 20 40 Case Temperature 60 Tc 80 100 0 (°C) 0° 10° 20° 40° 30° 40° 50° 50° 60° 60° 70° 70° 80° 90° 20 25 30 IF (mA) Wavelength characteristic Relative luminous Intensity 10° 15 35 40 (typ.) 1.0 Ta = 25°C (typ.) 20° 10 Forward current Radiation pattern 30° 5 0.8 0.6 0.4 0.2 80° 0 0.2 0.4 0.6 0.8 0.0 300 90° 1.0 400 500 Wavelength 4 600 700 800 λ (nm) 2007-10-01 TLWD1100(T11) Packaging These LED devices are packed in an aluminum envelope with a silica gel and a moisture indicator to avoid moisture absorption. The optical characteristics of the devices may be affected by exposure to moisture in the air before soldering and they should therefore be stored under the following conditions: 1. This moisture proof bag may be stored unopened within 12 months at the following conditions. Temperature: 5°C~30°C Humidity: 90% (max) 2. After opening the moisture proof bag, the devices should be assembled within 168 hours in an environment of 5°C to 30°C/60% RH or below. 3. If upon opening, the moisture indicator card shows humidity 30% or above (Color of indication changes to pink) or the expiration date has passed, the devices should be baked in taping with reel. After baking, use the baked devices within 72 hours, but perform baking only once. Baking conditions: 60±5°C, for 12 to 24 hours. Expiration date: 12 months from sealing date, which is imprinted on the same side as this label affixed. 4. Repeated baking can cause the peeling strength of the taping to change, then leads to trouble in mounting. Furthermore, prevent the devices from being destructed against static electricity for baking of it. 5. If the packing material of laminate would be broken, the hermeticity would deteriorate. Therefore, do not throw or drop the packed devices. Mounting Method Soldering • Reflow soldering Temperature profile (example) 10 s max (*) Package surface temperature (°C) 240°C max(*) 140~160°C max (*) (*) 4°C/s max 4°C/s max(*) 60~120 s max (*) Time • • • • • (s) The product is evaluated using above reflow soldering conditions. No additional test is performed exceed the condition (i.e. the condition more than (*)MAX values) as a evaluation. Please perform reflow soldering under the above conditions. Please perform the first reflow soldering with reference to the above temperature profile and within 168 h of opening the package. Second reflow soldering In case of second reflow soldering should be performed within 168 h of the first reflow under the above conditions. Storage conditions before the second reflow soldering: 30°C, 60% RH (max) Make any necessary soldering corrections manually. (only once at each soldering point) Soldering iron : 25 W Temperature : 300°C or less Time : within 3 s If the product needs to be performed by other soldering method (ex. wave soldering), please contact Toshiba sales representative. Recommended soldering pattern 1.65 1.15 Unit: mm 1.65 2.41 5 2007-10-01 TLWD1100(T11) Cleaning When cleaning is required after soldering, Toshiba recommends the following cleaning solvents. It is confirmed that these solvents have no effect on semiconductor devices in our dipping test (under the recommended conditions). In selecting the one for your actual usage, please perform sufficient review on washing condition, using condition and etc. ASAHI CLEAN AK-225AES KAO CLEAN TROUGH 750H PINE ALPHA ST-100S TOSHIBA TECHNOCARE (FRW-17, FRW-1, FRV-100) : (made by ASAHI GLASS) : (made by KAO) : (made by ARAKAWA CHEMICAL) : (made by GE TOSHIBA SILICONES) Precautions when Mounting Do not apply force to the plastic part of the LED under high-temperature conditions. To avoid damaging the LED plastic, do not apply friction using a hard material. When installing the PCB in a product, ensure that the device does not come into contact with other cmponents. Tape Specifications 1. Product number format The type of package used for shipment is denoted by a symbol suffix after the product number. The method of classification is as below. (this method, however does not apply to products whose electrical characteristics differ from standard Toshiba specifications) (1) Tape Type: T11 (4-mm pitch) (2) Example TLWD1100 (T11) Tape type Toshiba product No. 2. Tape dimensions Unit: mm Symbol Dimension Tolerance Symbol Dimension Tolerance D 1.5 +0.1/−0 P2 2.0 ±0.05 E 1.75 ±0.1 W 8.0 ±0.3 P0 4.0 ±0.1 P 4.0 ±0.1 t 0.3 ±0.05 A0 2.9 ±0.1 F 3.5 ±0.05 B0 3.7 ±0.1 D1 1.5 ±0.1 K0 2.3 ±0.1 K0 P0 D t P2 E F W B0 P D1 Polarity A0 6 2007-10-01 TLWD1100(T11) 3. Reel dimensions Unit: mm 9 ± 0.3 φ60 2 ± 0.5 φ13 φ44 +0 180 −4 11.4 ± 1.0 4. Leader and trailer sections of tape 40 mm or more 40 mm or more (Note 1) (Note 2) Leading part: 190 mm (min) Note1: Empty trailer section Note2: Empty leader section 7 2007-10-01 TLWD1100(T11) 5. Packing display (1) Packing quantity Reel 2,000 pcs Carton 10,000 pcs (2) Packing form: Each reel is sealed in an aluminum pack with silica gel. 6. Label format (1) Example: TLWD1100 (T11) P/N: TOSHIBA TYPE TLWD1100 ADDC (T11) Q’TY Lot Number Key code for TSB (RANK SYMBOL) 32C 2,000 pcs 2000 Use under 5-30degC/6-%RH within 168h SEAL DATE: DIFFUSED IN ***** ASSEMBLED IN ***** [[G]]/RoHS COMPATIBLE *Y3804xxxxxxxxxxxxxxxxx* (2) Label location • Reel • Carton Tape feel direction Label position Label position • The aluminum package in which the reel is supplied also has the label attached to center of one side. 8 2007-10-01 TLWD1100(T11) RESTRICTIONS ON PRODUCT USE 20070701-EN GENERAL • The information contained herein is subject to change without notice. • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 9 2007-10-01