TRSF3238 3-V TO 5.5-V MULTICHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER www.ti.com FEATURES • • • • • • • • • Auto-Powerdown Plus Operates With 3-V to 5.5-V VCC Supply Always-Active Noninverting Receiver Output (ROUT1B) Supports Operation From 250 kbit/s to 1 Mbit/s Low Standby Current . . . 1 μA Typical External Capacitors . . . 4 × 0.1 μF Accepts 5-V Logic Input With 3.3-V Supply Inter-Operable With TRSF3243 RS-232 Bus-Pin ESD Protection Exceeds ±15 kV Using Human-Body Model (HBM) APPLICATIONS • • • • • • • • • Battery-Powered Systems PDAs Notebooks Subnotebooks Laptops Palmtop PCs Hand-Held Equipment Modems Printers SLLS859 – AUGUST 2007 DB, DW, OR PW PACKAGE (TOP VIEW) C2 + GND C2− V− DOUT1 DOUT2 DOUT3 RIN1 RIN2 DOUT4 RIN3 DOUT5 FORCEON FORCEOFF 1 28 2 27 3 26 4 25 5 24 6 23 7 22 8 21 9 20 10 19 11 18 12 17 13 16 14 15 C1+ V+ VCC C1− DIN1 DIN2 DIN3 ROUT1 ROUT2 DIN4 ROUT3 DIN5 ROUT1B INVALID DESCRIPTION/ORDERING INFORMATION The TRSF3238 device consists of five line drivers, three line receivers, and a dual charge-pump circuit with ±15-kV ESD protection pin to pin (serial-port connection pins, including GND). The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-V supply. In addition, this device includes an always-active noninverting output (ROUT1B), which allows applications using the ring indicator to transmit data while the device is powered down. This device operates at data signaling rate up to 1 Mbit/s and at an increased slew-rate range of 24 V/μs to 150 V/μs. Flexible control options for power management are featured when the serial port and driver inputs are inactive. The auto-powerdown plus feature functions when FORCEON is low and FORCEOFF is high. During this mode of operation, if the device does not sense valid signal transitions on all receiver and driver inputs for approximately 30 s, the built-in charge pump and drivers are powered down, reducing the supply current to 1 μA. By disconnecting the serial port or placing the peripheral drivers off, auto-powerdown plus occurs if there is no activity in the logic levels for the driver inputs. Auto-powerdown plus can be disabled when FORCEON and FORCEOFF are high. With auto-powerdown plus enabled, the device automatically activates when a valid signal is applied to any receiver or driver input. INVALID is high (valid data) if any receiver input voltage is greater than 2.7 V or less than –2.7 V, or has been between –0.3 V and 0.3 V for less than 30 μs. INVALID is low (invalid data) if all receiver input voltages are between –0.3 V and 0.3 V for more than 30 μs. Refer to Figure 5 for receiver input levels. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2007, Texas Instruments Incorporated TRSF3238 3-V TO 5.5-V MULTICHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER www.ti.com SLLS859 – AUGUST 2007 ORDERING INFORMATION PACKAGE (1) (2) TA SOIC – DW 0°C to 70°C SSOP – DB TSSOP – PW SOIC – DW –40°C to 85°C SSOP – DB TSSOP – PW (1) (2) ORDERABLE PART NUMBER Tube of 50 TRSF3238CDW Reel of 2000 TRSF3238CDWR Tube of 50 TRSF3238CDB Reel of 2000 TRSF3238CDBR Tube of 50 TRSF3238CPW Reel of 2000 TRSF3238CPWR Tube of 50 TRSF3238IDW Reel of 2000 TRSF3238IDWR Tube of 50 TRSF3238IDB Reel of 2000 TRSF3238IDBR Tube of 50 TRSF3238IPW Reel of 2000 TRSF3238IPWR TOP-SIDE MARKING TRS3238EC TRS3238EC RT38C TRS3238EI TRS3238EI RT38I Package drawings, thermal data, and symbolization are available at www.ti.com/packaging. For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. FUNCTION TABLES abc Each Driver (1) INPUTS DIN (1) FORCEON FORCEOFF TIME ELAPSED SINCE LAST RIN OR DIN TRANSITION OUTPUT DOUT DRIVER STATUS X X L X Z Powered off L H H X H H H H X L Normal operation with auto-powerdown plus disabled L L H <30 s H H L H <30 s L L L H >30 s Z H L H >30 s Z Normal operation with auto-powerdown plus enabled Powered off by auto-powerdown plus feature H = high level, L = low level, X = irrelevant, Z = high impedance Each Receiver (1) INPUTS RIN2 RIN1, RIN3–RIN5 L H FORCEOFF ROUT1B ROUT X L X L Z X L X H Z L L H <30 s L H L H H <30 s L L H L H <30 s H H H H H <30 s H L Open Open H >30 s L H (1) 2 OUTPUTS TIME ELAPSED SINCE LAST RIN OR DIN TRANSITION RECEIVER STATUS Powered off while ROUT1B is active Normal operation with auto-powerdown plus disabled/enabled H = high level, L = low level, X = irrelevant, Z = high impedance (off), Open = input disconnected or connected driver off Submit Documentation Feedback www.ti.com TRSF3238 3-V TO 5.5-V MULTICHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER SLLS859 – AUGUST 2007 LOGIC DIAGRAM (POSITIVE LOGIC) DIN1 DIN2 DIN3 DIN4 DIN5 FORCEOFF FORCEON ROUT1B ROUT1 ROUT2 ROUT3 24 5 23 6 22 7 19 10 17 12 DOUT1 DOUT2 DOUT3 DOUT4 DOUT5 14 13 Auto-Powerdown Plus 15 INVALID 16 21 8 20 9 18 11 RIN1 RIN2 RIN3 Submit Documentation Feedback 3 TRSF3238 3-V TO 5.5-V MULTICHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER www.ti.com SLLS859 – AUGUST 2007 Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN MAX VCC Supply voltage range (2) –0.3 6 V V+ Positive-output supply voltage range (2) –0.3 7 V 0.3 –7 V 13 V V– Negative-output supply voltage range V+ – V– Supply voltage difference (2) VI Input voltage range VO Output voltage range θJA Package thermal impedance (3) (4) (2) TJ Operating virtual junction temperature Tstg Storage temperature range (1) (2) (3) (4) Driver (FORCEOFF, FORCEON) –0.3 6 Receiver –25 25 Driver Receiver (INVALID) –13.2 13.2 –0.3 VCC + 0.3 DB package 62 DW package 46 PW package 62 –65 UNIT V V °C/W 150 °C 150 °C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltages are with respect to network GND. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) – TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability. The package thermal impedance is calculated in accordance with JESD 51-7. Recommended Operating Conditions (1) See Figure 6 MIN NOM VCC = 3.3 V Supply voltage VCC = 5 V VIH Driver and control high-level input voltage DIN, FORCEOFF, FORCEON VIL Driver and control low-level input voltage DIN, FORCEOFF, FORCEON VI Driver and control input voltage DIN, FORCEOFF, FORCEON VI Receiver input voltage TA Operating free-air temperature (1) 3 3.3 3.6 4.5 5 5.5 VCC = 3.3 V VCC = 5 V UNIT V 2 V 2.4 0.8 V 0 5.5 V –25 25 V 0 70 –40 85 TRSF3238C TRSF3238I MAX °C Testing supply conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.15 V; C1–C4 = 0.22 μF at VCC = 3.3 V ± 0.3 V; and C1 = 0.047 μF and C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V. Electrical Characteristics (1) over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6) PARAMETER II ICC (1) (2) 4 Input leakage current Supply current TEST CONDITIONS FORCEOFF, FORCEON MIN TYP (2) MAX ±0.01 ±1 μA 0.5 2 mA Auto-powerdown plus disabled No load, FORCEOFF and FORCEON at VCC Powered off No load, FORCEOFF at GND 1 10 Auto-powerdown plus enabled No load, FORCEOFF at VCC, FORCEON at GND, All RIN are open or grounded 1 10 UNIT μA Testing supply conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.15 V; C1–C4 = 0.22 μF at VCC = 3.3 V ± 0.3 V; and C1 = 0.047 μF and C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V. All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C. Submit Documentation Feedback TRSF3238 3-V TO 5.5-V MULTICHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER www.ti.com SLLS859 – AUGUST 2007 DRIVER SECTION xxx Electrical Characteristics (1) over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6) PARAMETER MIN TYP (2) MAX TEST CONDITIONS VOH High-level output voltage All DOUT at RL = 3 kΩ to GND 5 5.4 VOL Low-level output voltage All DOUT at RL = 3 kΩ to GND –5 –5.4 IIH High-level input current VI = VCC IIL Low-level input current VI at GND ±0.01 μA μA ±0.01 ±1 ±35 ±60 VCC = 5.5 V, VO = 0 V ±40 ±90 VO = ±2 V ro Output resistance VCC, V+, and V– = 0 V, Ioff Output leakage current FORCEOFF = GND (2) (3) V ±1 VO = 0 V Short-circuit output current (3) (1) V VCC = 3.6 V, IOS 300 UNIT mA Ω 10M VO = ±12 V, VCC = 3 V to 3.6 V ±25 VO = ±10 V, VCC = 4.5 V to 5.5 V ±25 μA Testing supply conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.15 V; C1–C4 = 0.22 μF at VCC = 3.3 V ± 0.3 V; and C1 = 0.047 μF and C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V. All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C. Short-circuit durations should be controlled to prevent exceeding the device absolute power dissipation ratings, and not more than one output should be shorted at a time. Switching Characteristics (1) over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6) PARAMETER MIN TYP (2) MAX TEST CONDITIONS CL = 1000 pF Maximum data rate (see Figure 1) RL = 3 kΩ, One DOUT switching CL = 250 pF, VCC = 3 V to 4.5 V 1000 CL = 1000 pF, VCC = 4.5 V to 5.5 V 1000 tsk(p) Pulse skew (3) CL = 150 pF to 2500 pF, RL = 3 kΩ to 7 kΩ, See Figure 2 SR(tr) Slew rate, transition region (see Figure 1) CL = 150 pF to 1000 pF, RL = 3 kΩ to 7 kΩ, VCC = 3.3 V (1) (2) (3) UNIT 250 kbit/s 25 18 ns 150 V/μs Testing supply conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.15 V; C1–C4 = 0.22 μF at VCC = 3.3 V ± 0.3 V; and C1 = 0.047 μF and C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V. All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C. Pulse skew is defined as |tPLH – tPHL| of each channel of the same device. Submit Documentation Feedback 5 TRSF3238 3-V TO 5.5-V MULTICHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER www.ti.com SLLS859 – AUGUST 2007 RECEIVER SECTION xxx Electrical Characteristics (1) over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6) PARAMETER VOH High-level output voltage IOH = –1 mA VOL Low-level output voltage IOL = 1.6 mA VCC – 0.6 VCC – 0.1 MAX 1.5 2.4 VCC = 5 V 1.8 2.4 VIT– Negative-going input threshold voltage Vhys Input hysteresis (VIT+ – VIT–) Ioff Output leakage current (except ROUT1B) FORCEOFF = 0 V ri Input resistance VI = ±3 V to ±25 V VCC = 3.3 V 0.6 1.2 VCC = 5 V 0.8 1.5 UNIT V VCC = 3.3 V Positive-going input threshold voltage (2) TYP (2) 0.4 VIT+ (1) MIN TEST CONDITIONS V V V 0.3 V ±0.05 ±10 μA 5 7 kΩ 3 Testing supply conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.15 V; C1–C4 = 0.22 μF at VCC = 3.3 V ± 0.3 V; and C1 = 0.047 μF and C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V. All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C. Switching Characteristics (1) over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) PARAMETER TYP (2) UNIT tPLH Propagation delay time, low- to high-level output CL = 150 pF, See Figure 3 150 ns tPHL Propagation delay time, high- to low-level output CL = 150 pF, See Figure 3 150 ns ten Output enable time CL = 150 pF, RL = 3 kΩ, See Figure 4 200 ns tdis Output disable time CL = 150 pF, RL = 3 kΩ, See Figure 4 200 ns tsk(p) Pulse skew (3) See Figure 3 50 ns (1) (2) (3) 6 TEST CONDITIONS Testing supply conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.15 V; C1–C4 = 0.22 μF at VCC = 3.3 V ± 0.3 V; and C1 = 0.047 μF and C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V. All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C. Pulse skew is defined as |tPLH – tPHL| of each channel of the same device. Submit Documentation Feedback TRSF3238 3-V TO 5.5-V MULTICHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER www.ti.com SLLS859 – AUGUST 2007 AUTO-POWERDOWN PLUS SECTION xxx Electrical Characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5) PARAMETER TEST CONDITIONS MIN VT+(valid) Receiver input threshold for INVALID high-level output voltage FORCEON = GND, FORCEOFF = VCC VT–(valid) Receiver input threshold for INVALID high-level output voltage FORCEON = GND, FORCEOFF = VCC –2.7 VT(invalid) Receiver input threshold for INVALID low-level output voltage FORCEON = GND, FORCEOFF = VCC –0.3 VOH INVALID high-level output voltage IOH = –1 mA, FORCEON = GND, FORCEOFF = VCC VOL INVALID low-level output voltage IOL = 1.6 mA, FORCEON = GND, FORCEOFF = VCC MAX 2.7 UNIT V V 0.3 VCC – 0.6 V V 0.4 V Switching Characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5) PARAMETER MIN TYP (1) MAX UNIT tvalid Propagation delay time, low- to high-level output 0.1 μs tinvalid Propagation delay time, high- to low-level output 50 μs ten Supply enable time 25 tdis Receiver or driver edge to auto-powerdown plus (1) 15 30 μs 60 s All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C. Submit Documentation Feedback 7 TRSF3238 3-V TO 5.5-V MULTICHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER www.ti.com SLLS859 – AUGUST 2007 PARAMETER MEASUREMENT INFORMATION 3V Generator (see Note B) Input RS-232 Output 50 Ω RL tTHL CL (see Note A) 3V FORCEOFF TEST CIRCUIT 0V 3V 3V Output SR(tr) + tTLH −3 V −3 V 6V t THL or tTLH VOH VOL VOLTAGE WAVEFORMS A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: PRR = 1 Mbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns. Figure 1. Driver Slew Rate 3V Generator (see Note B) RS-232 Output 50 Ω RL Input 1.5 V 1.5 V 0V CL (see Note A) tPHL tPLH VOH 3V FORCEOFF 50% 50% Output VOL TEST CIRCUIT VOLTAGE WAVEFORMS A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: PRR = 1 Mbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns. Figure 2. Driver Pulse Skew 3 V or 0 V FORCEON 3V Input 1.5 V 1.5 V −3 V Output Generator (see Note B) tPHL 50 Ω 3V FORCEOFF tPLH CL (see Note A) VOH 50% Output 50% VOL TEST CIRCUIT VOLTAGE WAVEFORMS A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns. Figure 3. Receiver Propagation Delay Times 8 Submit Documentation Feedback TRSF3238 3-V TO 5.5-V MULTICHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER www.ti.com SLLS859 – AUGUST 2007 PARAMETER MEASUREMENT INFORMATION (continued) 3V Input VCC 3 V or 0 V FORCEON 1.5 V 0V tPZH (S1 at GND) tPHZ (S1 at GND) RL RS-232 Input 1.5 V GND S1 VOH Output 50% Output CL (see Note A) FORCEOFF Generator (see Note B) 0.3 V tPLZ (S1 at VCC) 50 Ω tPZL (S1 at VCC) 0.3 V Output 50% VOL TEST CIRCUIT VOLTAGE WAVEFORMS A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns. C. tPLZ and tPHZ are the same as tdis. D. tPZL and tPZH are the same as ten. Figure 4. Receiver Enable and Disable Times Submit Documentation Feedback 9 TRSF3238 3-V TO 5.5-V MULTICHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER www.ti.com SLLS859 – AUGUST 2007 PARAMETER MEASUREMENT INFORMATION (continued) ÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎ Valid RS-232 Level, INVALID High ROUT Generator (see Note B) 2.7 V 50 Ω Indeterminate 0.3 V 0V −0.3 V Indeterminate AutoPowerdown Plus INVALID −2.7 V CL = 30 pF (see Note A) Valid RS-232 Level, INVALID High † FORCEOFF FORCEON If Signal Remains Within This Region for More Than 30 µs, INVALID Is Low† DIN DOUT Auto-powerdown plus disables drivers and reduces supply current to 1 µA. TEST CIRCUIT NOTES: A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: PRR = 5 kbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns. Receiver Input 3V 2.7 V 0V 0V −2.7 V −3 V tinvalid tvalid INVALID Output Driver Input 50% VCC 50% 0V 3 V to 5 V 50% 50% 0V ≈5.5 V Driver Output ≈ −5.5 V tdis ten tdis ten V+ Supply Voltages V+ V+ −0.3 V V− +0.3 V V− V− Voltage Waveforms and Timing Diagrams Figure 5. INVALID Propagation-Delay Times and Supply-Enabling Time 10 Submit Documentation Feedback TRSF3238 3-V TO 5.5-V MULTICHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER www.ti.com SLLS859 – AUGUST 2007 APPLICATION INFORMATION CBYPASS = 0.1 µF + − 1 2 + C2 27 + GND − 4 + V+ 28 − 3 − C1+ C2+ C2− VCC V− C1− C4 DOUT1 DOUT2 DOUT3 RIN1 C3† + − 26 C1 25 5 24 6 23 7 22 8 21 9 20 DIN1 DIN2 DIN3 ROUT1 Serial Port RIN2 ROUT2 Logic I/Os 5 kΩ DOUT4 RIN3 10 19 11 18 DIN4 ROUT3 5 kΩ DOUT5 12 17 16 DIN5 ROUT1B 5 kΩ FORCEON FORCEOFF 13 14 AutoPowerdown Plus 15 INVALID VCC vs CAPACITOR VALUES VCC † C3 can be connected to VCC or GND. A.Resistor values shown are nominal. 3.3 V ± 0.15 V 3.3 V ± 0.3 V 5 V ± 0.5 V 3 V to 5.5 V C1 0.1 µF 0.22 µF 0.047 µF 0.22 µF C2, C3, and C4 0.1 µF 0.22 µF 0.33 µF 1 µF Figure 6. Typical Operating Circuit and Capacitor Values Submit Documentation Feedback 11 PACKAGE OPTION ADDENDUM www.ti.com 24-Jul-2010 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) TRSF3238CDB ACTIVE SSOP DB 28 TBD Call TI Call TI Purchase Samples TRSF3238CDBG4 ACTIVE SSOP DB 28 TBD Call TI Call TI Purchase Samples TRSF3238CDBR ACTIVE SSOP DB 28 TBD Call TI Call TI Purchase Samples TRSF3238CDBRG4 ACTIVE SSOP DB 28 TBD Call TI Call TI Purchase Samples TRSF3238CDW ACTIVE SOIC DW 28 TBD Call TI Call TI Purchase Samples TRSF3238CDWG4 ACTIVE SOIC DW 28 TBD Call TI Call TI Purchase Samples TRSF3238CDWR ACTIVE SOIC DW 28 TBD Call TI Call TI Purchase Samples TRSF3238CDWRG4 ACTIVE SOIC DW 28 TBD Call TI Call TI Purchase Samples TRSF3238CPW ACTIVE TSSOP PW 28 TBD Call TI Call TI Purchase Samples TRSF3238CPWG4 ACTIVE TSSOP PW 28 TBD Call TI Call TI Purchase Samples TRSF3238CPWR ACTIVE TSSOP PW 28 TBD Call TI Call TI Purchase Samples TRSF3238CPWRG4 ACTIVE TSSOP PW 28 TBD Call TI Call TI Purchase Samples TRSF3238IDB ACTIVE SSOP DB 28 TBD Call TI Call TI Purchase Samples TRSF3238IDBG4 ACTIVE SSOP DB 28 TBD Call TI Call TI Purchase Samples TRSF3238IDBR ACTIVE SSOP DB 28 TBD Call TI Call TI Purchase Samples TRSF3238IDBRG4 ACTIVE SSOP DB 28 TBD Call TI Call TI Purchase Samples TRSF3238IDW ACTIVE SOIC DW 28 TBD Call TI Call TI Purchase Samples TRSF3238IDWG4 ACTIVE SOIC DW 28 TBD Call TI Call TI Purchase Samples TRSF3238IDWR ACTIVE SOIC DW 28 TBD Call TI Call TI Purchase Samples TRSF3238IDWRG4 ACTIVE SOIC DW 28 TBD Call TI Call TI Purchase Samples TRSF3238IPW ACTIVE TSSOP PW 28 TBD Call TI Call TI Purchase Samples TRSF3238IPWG4 ACTIVE TSSOP PW 28 TBD Call TI Call TI Purchase Samples TRSF3238IPWR ACTIVE TSSOP PW 28 TBD Call TI Call TI Purchase Samples TRSF3238IPWRG4 ACTIVE TSSOP PW 28 TBD Call TI Call TI Purchase Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 24-Jul-2010 (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 MECHANICAL DATA MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 28 PINS SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,25 0,09 8,20 7,40 5,60 5,00 Gage Plane 1 14 0,25 A 0°–ā8° 0,95 0,55 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 /E 12/01 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0°– 8° A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DLP® Products www.dlp.com Communications and Telecom www.ti.com/communications DSP dsp.ti.com Computers and Peripherals www.ti.com/computers Clocks and Timers www.ti.com/clocks Consumer Electronics www.ti.com/consumer-apps Interface interface.ti.com Energy www.ti.com/energy Logic logic.ti.com Industrial www.ti.com/industrial Power Mgmt power.ti.com Medical www.ti.com/medical Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Space, Avionics & Defense www.ti.com/space-avionics-defense RF/IF and ZigBee® Solutions www.ti.com/lprf Video and Imaging www.ti.com/video Wireless www.ti.com/wireless-apps Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2010, Texas Instruments Incorporated