Data Sheet 29310D* 2981 THRU 2984 8-CHANNEL SOURCE DRIVERS UDN2981A thru UDN2984A 1 18 2 17 3 16 4 15 5 14 6 13 7 12 8 11 VS GND Dwg. No. A-10, 243 Note that the UDN2980A series (dual in-line package) and UDN2980LW series (small-outline IC package) are electrically identical and share a common terminal number assignment. ABSOLUTE MAXIMUM RATINGS at 25°C Free-Air Temperature Output Voltage Range, VCE (UDN2981A, UDN2982A, UDN2982LW, and A2982SLW) . . 5 V to 50 V (UDN2983A, UDN2984A, UDN2984LW, and A2984SLW) . 35 V to 80 V Input Voltage, VIN (UDN2981A and UDN2983A) . . . . . . . . . 15 V (UDN2982A, UDN2984A, UDN2982LW, UDN2984LW, A2982SLW, and A2984SLW) . . . . . . . . . 20 V Output Current, IOUT . . . . . . . . . . . . . . -500 mA Package Power Dissipation, PD . . . . . . . . . . . . . . . . . . . . . . . See Graph Operating Temperature Range, TA . . . . . . . . . . . . . . . . . . . . -20°C to +85°C Storage Temperature Range, TS . . . . . . . . . . . . . . . . . . . -55°C to +150°C Recommended for high-side switching applications that benefit from separate logic and load grounds, these devices encompass load supply voltages to 80 V and output currents to -500 mA. These 8-channel source drivers are useful for interfacing between low-level logic and high-current loads. Typical loads include relays, solenoids, lamps, stepper and/or servo motors, print hammers, and LEDs. All devices may be used with 5 V logic systems — TTL, Schottky TTL, DTL, and 5 V CMOS. The UDN2981A, UDN2982A, UDN2982LW, and A2982SLW are electrically interchangeable, will withstand a maximum output off voltage of 50 V, and operate to a minimum of 5 V; the UDN2983A, UDN2984A, UDN2984LW, and A2984SLW drivers are electrically interchangeable, will withstand an output voltage of 80 V, and operate to a minimum of 35 V. All devices in this series integrate input current limiting resistors and output transient suppression diodes, and are activated by an active high input. The suffix ‘A’ (all devices) indicates an 18-lead plastic dual in-line package with copper lead frame for optimum power dissipation. Under normal operating conditions, these devices will sustain 120 mA continuously for each of the eight outputs at an ambient temperature of +50°C and a supply of 15 V. The suffix ‘LW’ (UDN2982LW and UDN2984LW only) indicates an 18lead surface-mountable wide-body SOIC package; the A2982SLW and A2984SLW are provided in a 20-lead wide-body SOIC package with improved thermal characteristics. The UDN2982A, UDN2982LW, A2982SLW, UDN2984A, UDN2984LW, and A2984SLW drivers are also available for operation over an extended temperature range to -40°C. To order, change the prefix ‘UDN’ to ‘UDQ’ or the suffix ‘SLW’ to ‘ELW’. FEATURES ■ ■ ■ ■ ■ TTL, DTL, PMOS, or CMOS Compatible Inputs 500 mA Output Source Current Capability Transient-Protected Outputs Output Breakdown Voltage to 80 V DIP or SOIC Packaging Always order by complete part number, e.g., UDN2981A . Note that all devices are not available in all package styles. 2981 THRU 2984 8-CHANNEL SOURCE DRIVERS One of Eight Drivers V5 9 20 K 7.2 K 2983/84 ONLY 3K INPUT OUTPUT 1.5 K GROUND Dwg. No. A-10,242B A2982SLW and A2984SLW +V S NO CONNECTION 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 NC NC 11 GROUND NO CONNECTION ALLOWABLE PACKAGE POWER DISSIPATION IN WATTS 2.5 18-PIN DIP, RθJA = 60°C/W 2.0 20-LEAD SOIC, RθJA = 70°C/W 18-LEAD SOIC, RθJA = 80°C/W 1.5 1.0 0.5 0 Dwg. PP-064-2 25 50 75 100 125 AMBIENT TEMPERATURE IN °C 150 Dwg. GP-022-4 2 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 W Copyright © 1977, 2000 Allegro MicroSystems, Inc. 2981 THRU 2984 8-CHANNEL SOURCE DRIVERS ELECTRICAL CHARACTERISTICS at TA = +25°C (unless otherwise specified). Characteristic Output Leakage Current Output Sustaining Symbol ICEX VCE(SUS) Voltage Applicable Devices Test Conditions Test Fig. Min. Limits Typ. Max. 2981/82† VIN = 0.4 V*, VS = 50 V, TA = +70°C 1 — — 200 µA 2983/84† VIN = 0.4 V*, VS = 80 V, TA = +70°C 1 — — 200 µA 2981/82† IOUT = -45 mA — 35 — — V 2983/84† IOUT = -70 mA — 45 — — V VIN = 2.4 V, IOUT = -100 mA 2 — 1.6 1.8 V VIN = 2.4 V, IOUT = -225 mA 2 — 1.7 1.9 V VIN = 2.4 V, IOUT = -350 mA 2 — 1.8 2.0 V VIN = 2.4 V 3 — 140 200 µA VIN = 3.85 V 3 — 310 450 µA VIN = 2.4 V 3 — 140 200 µA VIN = 12 V 3 — 1.25 1.93 mA 2981/83A VIN = 2.4 V, VCE = 2.0 V 2 -350 — — mA 2982/84† VIN = 2.4 V, VCE = 2.0 V 2 -350 — — mA 2981/82† VIN = 2.4 V*, VS = 50 V 4 — — 10 mA 2983/84† VIN = 2.4 V*, VS = 80 V 4 — — 10 mA 2981/82† VR = 50 V, VIN = 0.4 V* 5 — — 50 µA 2983/84† VR = 80 V, VIN = 0.4 V* 5 — — 50 µA Collector-Emitter Saturation Voltage VCE(SAT) Input Current All 2981/83A IIN(ON) 2982/84† Output Source Current lOUT (Outputs Open) Supply Current IS Leakage Current Clamp Diode IR Forward Voltage Units Clamp Diode VF All IF = 350 mA 6 — 1.5 2.0 V Turn-On Delay tON All 0.5 EIN to 0.5 EOUT, RL = 100Ω, VS = 35 V — — 1.0 2.0 µs Turn-Off Delay tOFF All 0.5 EIN to 0.5 EOUT, RL = 100Ω, VS = 35 V, See Note — — 5.0 10 µs NOTES: Turn-off delay is influenced by load conditions. Systems applications well below the specified output loading may require timing considerations for some designs, i.e., multiplexed displays or when used in combination with sink drivers in a totem pole configuration. Negative current is defined as coming out of (sourcing) the specified device terminal. * All inputs simultaneously. † Complete part number includes a prefix (A or UDN) and a suffix (A or SLW) as follows: UDN2981A, UDN2982A, UDN2982LW, or A2982SLW, UDN2983A, UDN2984A, UDN2984LW, or A2984SLW. www.allegromicro.com 3 2981 THRU 2984 8-CHANNEL SOURCE DRIVERS TEST FIGURES Figure 1 Figure 2 VS VS V Figure 3 V V CE S I IN mA mA OPEN I OUT V VIN µA IN V IN I CEX Dwg. No. A-11,083 Dwg. No. A-11,084 Figure 4 Figure 5 VS Figure 6 VS I S mA OPEN µA IR OPEN OPEN VF VIN VIN Dwg. No. A-11,086 4 Dwg. No. A-11,085 Dwg. No. A-11,087 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 V I F Dwg. No. A-11,088 2981 THRU 2984 8-CHANNEL SOURCE DRIVERS Allowable peak collector current as a function of duty cycle 500 500 450 450 ALLOWABLE PEAK COLLECTOR CURRENT IN mA AT 70°C ALLOWABLE PEAK COLLECTOR CURRENT IN mA AT 50°C Series UDN2980A 400 RECOMMENDED MAXIMUM OUTPUT CURRENT 350 3 300 4 5 250 6 8 200 7 NUMBER OF OUTPUTS CONDUCTING SIMULTANEOUSLY 150 100 VS = 35 V 400 RECOMMENDED MAXIMUM OUTPUT CURRENT 350 300 3 4 250 5 6 200 NUMBER OF OUTPUTS CONDUCTING SIMULTANEOUSLY 7 8 150 100 VS = 35 V 50 50 0 0 10 20 30 50 60 40 PER CENT DUTY CYCLE 70 0 80 90 0 100 10 20 30 70 50 60 40 PER CENT DUTY CYCLE Dwg. No. A-11,106B 90 80 100 Dwg. No. A-11,111B 500 500 450 450 ALLOWABLE PEAK COLLECTOR CURRENT IN mA AT 70°C ALLOWABLE PEAK COLLECTOR CURRENT IN mA AT 50°C UDN2981A and UDN2982A 400 RECOMMENDED MAXIMUM OUTPUT CURRENT 350 3 300 4 5 250 7 6 8 200 NUMBER OF OUTPUTS CONDUCTING SIMULTANEOUSLY 150 100 VS = 15 V 400 RECOMMENDED MAXIMUM OUTPUT CURRENT 350 300 3 4 250 5 6 200 7 8 NUMBER OF OUTPUTS CONDUCTING SIMULTANEOUSLY 150 100 VS = 15 V 50 50 0 0 10 20 30 50 60 40 PER CENT DUTY CYCLE 70 80 90 0 100 Dwg. No. A-11,107B www.allegromicro.com 0 10 20 30 50 60 40 PER CENT DUTY CYCLE 70 80 90 100 Dwg. No. A-11,108B 5 2981 THRU 2984 8-CHANNEL SOURCE DRIVERS Allowable peak collector current as a function of duty cycle 500 500 450 450 ALLOWABLE PEAK COLLECTOR CURRENT IN mA AT 70°C ALLOWABLE PEAK COLLECTOR CURRENT IN mA AT 50°C UDN2983A and UDN2984A 400 RECOMMENDED MAXIMUM OUTPUT CURRENT 350 3 300 4 250 5 6 200 8 7 NUMBER OF OUTPUTS CONDUCTING SIMULTANEOUSLY 150 100 400 RECOMMENDED MAXIMUM OUTPUT CURRENT 350 300 3 250 4 5 6 200 8 7 NUMBER OF OUTPUTS CONDUCTING SIMULTANEOUSLY 150 100 VS = 60 V VS = 60 V 50 50 0 0 0 10 20 30 50 60 40 PER CENT DUTY CYCLE 70 80 90 100 10 0 20 30 50 60 40 PER CENT DUTY CYCLE Dwg. No. A-11,109B 70 80 90 100 Dwg. No. A-11,110B Input current as a function of input voltage Typical electrosensitive printer application 2.5 ELECTRODES INPUT CURRENT, I IN (mA) 2.0 1.5 R IN1 1 18 IN2 2 17 IN3 3 16 IN4 4 15 IN 5 5 14 IN6 6 13 IN7 7 12 IN8 8 11 VS 9 10 R R UM R IM X MA 1.0 R AL PIC TY R 0.5 R R 2 4 6 8 10 12 INPUT VOLTAGE (VOLTS) L L L L L L L L Dwg. No. A-11,115B Dwg. No. A-11,113A 6 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 2981 THRU 2984 8-CHANNEL SOURCE DRIVERS UDN2981A, UDN2982A, UDN2983A, and UDN2984A Dimensions in Inches (controlling dimensions) 0.014 0.008 10 18 0.430 MAX 0.280 0.240 0.300 BSC 1 0.070 0.045 9 0.100 0.920 0.880 0.005 BSC MIN 0.210 MAX 0.015 0.150 0.115 MIN 0.022 0.014 Dwg. MA-001-18A in Dimensions in Millimeters (for reference only) 18 0.355 0.204 10 10.92 MAX 7.11 6.10 7.62 BSC 1 1.77 1.15 2.54 23.37 22.35 BSC 9 0.13 MIN 5.33 MAX 0.39 3.81 2.93 MIN 0.558 0.356 NOTES: 1. 2. 3. 4. Dwg. MA-001-18A mm Exact body and lead configuration at vendor’s option within limits shown. Lead spacing tolerance is non-cumulative. Lead thickness is measured at seating plane or below. Supplied in standard sticks/tubes of 21 devices. www.allegromicro.com 7 2981 THRU 2984 8-CHANNEL SOURCE DRIVERS UDN2982LW and UDN2984LW (add “TR” to part number for tape and reel) Dimensions in Inches (for reference only) 18 10 0.0125 0.0091 0.419 0.394 0.2992 0.2914 0.050 0.016 0.020 0.013 1 2 0.050 3 0° TO 8° BSC 0.4625 0.4469 0.0926 0.1043 0.0040 MIN. Dwg. MA-008-18A in Dimensions in Millimeters (controlling dimensions) 18 10 0.32 0.23 10.65 10.00 7.60 7.40 1.27 0.40 0.51 0.33 1 2 1.27 3 11.75 11.35 BSC 0° TO 8° 2.65 2.35 0.10 MIN. Dwg. MA-008-18A mm NOTES: 1. Exact body and lead configuration at vendor’s option within limits shown. 2. Lead spacing tolerance is non-cumetive. 3. Supplied in standard sticks/tubes of 41 devices or add “TR” to part number for tape and reel. 8 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 2981 THRU 2984 8-CHANNEL SOURCE DRIVERS A2982SLW and A2984SLW (add “TR” to part number for tape and reel) Dimensions in Inches (for reference only) 20 11 0.0125 0.0091 0.419 0.394 0.2992 0.2914 0.050 0.016 0.020 0.013 1 2 0.050 3 0.5118 0.4961 0° TO 8° BSC 0.0926 0.1043 Dwg. MA-008-20 in 0.0040 MIN. Dimensions in Millimeters (controlling dimensions) 20 11 0.32 0.23 10.65 10.00 7.60 7.40 1.27 0.40 0.51 0.33 1 2 1.27 3 13.00 12.60 BSC 0° TO 8° 2.65 2.35 0.10 MIN. Dwg. MA-008-20 mm NOTES: 1. Exact body and lead configuration at vendor’s option within limits shown. 2. Lead spacing tolerance is non-cumulative. 3. Supplied in standard sticks/tubes of 37 devices or add “TR” to part number for tape and reel. www.allegromicro.com 9 2981 THRU 2984 8-CHANNEL SOURCE DRIVERS POWER SOURCE DRIVERS IN ORDER OF 1) OUTPUT CURRENT, 2) OUTPUT VOLTAGE, 3) NUMBER OF DRIVERS Features Output Ratings * mA -25 V 60 60 60 # 8 10 12 Serial Input – X X Latched Diode Saturated Drivers Clamp Outputs X – – X active pull-down – X active pull-down – Internal Protection – – – † Part Number 5815 5810-F and 6809/10 5811 and 6811 60 20 X X active pull-down – – 5812-F and 6812 60 32 X X active pull-down – – 5818-F and 6818 85 8 – – – – – 6118 -120 -25 8 – – X X – 2585 30 8 – – X X – 2985 50 8 X X X X – 5895 -350 35 8 – – X – X 2987 50 8 – – X – – 2981 and 2982 50 8 X X X – – 5891 -50 8 – – X – – 2580 80 8 – – X – – 2983 and 2984 80 8 X X X – – 5890 -80 8 – – X – – 2588 -500 6 1 – – – MOSFET X 2525 and 2535 6 2 – – – MOSFET X 2526 and 2536 -4000 60 4 – – X – – 2944 * Current is maximum specified test condition, voltage is maximum rating. See specification for sustaining voltage limits or over-current protection voltage limits. † Complete part number includes additional characters to indicate operating temperature range and package style. The products described here are manufactured under one or more U.S. patents or U.S. patents pending. Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro products are not authorized for use as critical components in life-support devices or systems without express written approval. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. 10 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000