EMB10 / UMB10N / IMB10A Transistors General purpose (dual digital transistors) EMB10 / UMB10N / IMB10A zExternal dimensions (Unit : mm) zFeatures 1) Two DTA123J chips in a EMT or UMT or SMT package. 2) Mounting possible with EMT3 or UMT3 or SMT3 automatic mounting machines. 3) Transistor elements are independent, eliminating interference. 4) Mounting cost and area can be cut in half. (3) (2) (6) (1) 1.2 1.6 0.5 0.5 1.0 1.6 (4) (5) 0.5 0.13 0.22 EMB10 Each lead has same dimensions ROHM : EMT6 Abbreviated symbol : B10 0.65 (1) 1.25 2.0 1.3 (3) (2) (4) (6) (5) 0.2 0.65 UMB10N zStructure Epitaxial planar type PNP silicon transistor (Built-in resistor type) 0.1Min. 0to0.1 0.7 0.15 0.9 2.1 The following characteristics apply to both DTr1 and DTr2. Each lead has same dimensions zEquivalent circuit ROHM : UMT6 EIAJ : SC-88 R2 R1 (3) (2) (6) 0.95 0.95 1.9 2.9 (1) (2) R1=2.2kΩ R2=47kΩ (1) (3) R2 R1 (4) (5) (5) R2=47kΩ (4) DTr2 (6) DTr1 DTr1 DTr2 IMB10A (4) (5) (6) R1 R2 (3) (2) (1) R1 R2 R1=2.2kΩ Abbreviated symbol : B10 IMB10A 0.3 EMB10 / UMB10N 1.6 0.3to0.6 Symbol Limits Unit Supply voltage VCC −50 V Input voltage VIN Parameter −12 5 Output current EMB10, UMB10N Power dissipation IMB10A IO −100 IC (Max.) −100 Pd 150 (TOTAL) 1.1 0to0.1 zAbsolute maximum ratings (Ta = 25°C) 0.8 0.15 2.8 Each lead has same dimensions ROHM : SMT6 EIAJ : SC-74 Abbreviated symbol : B10 V mA mW 300 (TOTAL) Junction temperature Tj 150 ˚C Storage temperature Tstg −55 to +150 ˚C ∗1 ∗2 ∗1 120mW per element must not be exceeded. ∗2 200mW per element must not be exceeded. Rev.A 1/2 EMB10 / UMB10N / IMB10A Transistors zElectrical characteristics (Ta = 25°C) Parameter Symbol Min. Typ. Max. VI (off) − − −0.5 VI (on) −1.1 − − VO (on) − −0.1 −0.3 V II − − −3.6 mA VI=−5V IO (off) − − −0.5 µA VCC=−50V, VI=0V DC current gain GI 80 − − − Transition frequency fT − 250 − MHz Input resistance R1 1.54 2.2 2.86 kΩ − Resistance ratio R2 / R 1 17 21 26 − − Input voltage Output voltage Input current Output current ∗ Unit Conditions VCC=−5V, IO=−100µA V VO=−0.3V, IO=−5mA IO/II=−5mA/−0.25mA VO=−5V, IO=−10mA ∗ VCE=−10V, IE=5mA, f=100MHz Transition frequency of the device zPackaging specifications Package Type Taping Code T2R TN T148 Basic ordering unit (pieces) 8000 3000 3000 EMB10 UMB10N IMB10A zElectrical characteristic curves −100 −10m VO=−0.3V 1k 500 −10 −5 −2 Ta=−40˚C 25˚C 100˚C −1 −500m −200m −1m −500µ Ta=100˚C 25˚C −40˚C −200µ −100µ −50µ −20µ −10µ −2m −5m −10m −20m −50m −100m OUTPUT CURRENT : IO (A) Fig.1 Input voltage vs. output current (ON characteristics) −1 200 Ta=100˚C 25˚C −40˚C 100 50 20 10 5 −5µ 2 −2µ −100m −100µ −200µ −500µ −1m −1µ 1 0 −0.5 −1 −1.5 −2 −2.5 INPUT VOLTAGE : VI (off) (V) Fig.2 Output current vs. input voltage (OFF characteristics) −3 −100µ −200µ −500µ −1m −2m −5m −10m −20m −50m−100m OUTPUT CURRENT : IO (A) Fig.3 DC current gain vs. output current lO/lI =20 −500m OUTPUT VOLTAGE : VO (on) (V) DC CURRENT GAIN : GI OUTPUT CURRENT : Io (A) INPUT VOLTAGE : VI (on) (V) −2m −20 VO=−5V VCC=−5V −5m −50 Ta=100˚C 25˚C −40˚C −200m −100m −50m −20m −10m −5m −-2m −1m −100µ −200µ −500µ −1m −2m −5m −10m −20m −50m−100m OUTPUT CURRENT : IO (A) Fig.4 Output voltage vs. output current Rev.A 2/2 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1