45 Data Sheet FasTrak Mini E-Grade Family DC-DC Converter Module Features • • • • • • • • • Input voltages: 24, 48, 300 & 375 V DC outputs: 3.3 V – 48 V Programmable output: 10 to 110% Regulation: ±0.5% no load to full load Efficiency: Up to 88% Max operating temp: 100°C, full load Power Density: Up to 120 W/cubic Inch Parallelable, with N+M fault tolerance Low noise ZCS/ZVS architecture Product Overview These DC-DC converter modules use advanced power processing, control and packaging technologies to provide the performance, flexibility, reliability and cost effectiveness of a mature power component. High frequency ZCS/ZVS switching provide high power density with low noise and high efficiency. Off-line systems with autoranging or PFC front-ends, industrial and process control, distributed power, medical, ATE, communications, defense, aerospace Part Numbering e.g. V300B12E250BL2 B Input Voltage 24: 48: 300: 375: 18 – 36 Vin 36 – 75 Vin 180 – 375 Vin 250 – 425 Vin Input 24 V 48 V 300 V 375 V Absolute Maximum Ratings Parameter Applications V Shown actual size: 2.28 x 2.2 x 0.5 in 57,9 x 55,9 x 12,7 mm E Output Voltage 3V3: 3.3V 5: 5 V 12: 12 V 15: 15 V 24: 24 V 28: 28 V 48: 48 V Output Power (Watts) 3.3 Vout 5 Vout >5 Vout 150 200 200 150 200 250 150 200 250 150 200 250 B Pin Style Blank: Short Tin/Lead L: Long Tin/Lead S:Short Gold N: Long Gold Baseplate Blank: Slotted 1: Threaded 2: Through-hole Rating Unit -0.5 to +36 Vdc 48 Vin -0.5 to +75 Vdc 300 Vin -0.5 to +375 Vdc 375 Vin +In to –In voltage 24 Vin -0.5 to +425 Vdc PC to –In voltage -0.5 to +7.0 Vdc PR to –In voltage -0.5 to +7.0 Vdc SC to –Out voltage -0.5 to +1.5 Vdc –Sense to –Out voltage 1.0 Vdc Isolation voltage (in to out) 3000 Vrms Isolation voltage (in to base) 1550 Vrms Isolation voltage (out to base) 500 Vrms Operating temperature -10 to +100 °C Storage temperature -20 to +125 °C Pin soldering temperature 500 (260) °F (°C) <5 sec; wave solder Pin soldering temperature 750 (390) °F (°C) <7 sec; hand solder 5 (0.57) in-lbs (N-m) Mounting torque For a description of pin options, see page 6.Baseplate options include slotted flanges, threaded and through-hole. See page 7 for dimensions. For other package sizes and powerlevels, see the FasTrak Maxi (full size) and FasTrak Micro (quarter size) datasheets Notes 6 each, # 4-40 or M3 Thermal Resistance and Capacity Parameter Min Typ Max Unit Baseplate to sink; flat, greased surface 0.16 °C/Watt Baseplate to sink; thermal pad (P/N 20263) 0.14 °C/Watt Baseplate to ambient 8.0 °C/Watt Baseplate to ambient; 1000 LFM 1.9 °C/Watt Thermal capacity 83 Watt-sec/°C Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715 FasTrak Mini E-Grade Family Set your site on VICOR at www.vicorpower.com Rev. 1.0 Page 1 of 8 ELECTRICAL CHARACTERISTICS Electrical characteristics apply over the full operating range of input voltage, output load (resistive) and baseplate temperature, unless otherwise specified. All temperatures refer to the operating temperature at the center of the baseplate. MODULE OPERATING SPECIFICATIONS Parameter Min Typ Max Surge Withstand Unit Notes 24 Vin 18 24 36 50 Vdc <100 ms surge withstand 48 Vin 36 48 75 100 Vdc 300 Vin 180 300 375 400 Vdc 375 Vin 250 375 425 500 Vdc Input voltage Output voltage setpoint ±1 % Nominal input; full load; 25°C MODULE OUTPUT VOLTAGE RELATED SPECIFICATIONS Parameter 3.3V 5V 12V 15V 24V 28V 48V Unit Notes Efficiency (typ.) 80.0 83.5 85.5 87.0 88.0 89.0 90.0 % Nominal input; 80% load; 25°C Ripple and noise, p-p (typ.) 60 70 130 90 80 65 50 mV Nominal input; full load; 25°C; 20 MHz BW Output OVP setpoint (nom.) 4.3 6.3 14.3 17.8 28.1 32.7 55.7 Volts 25°C; recycle input voltage to restart ( 1 minute off ) Dissipation, standby (typ.) 5.6 6.2 8.0 8.0 6.0 7.4 8.5 Watts No load; nominal input Load regulation (max.) 0.5 0.5 0.5 0.5 0.5 0.5 0.5 ±% Vout Current limit (typ.) 125 125 125 125 125 125 125 % Iout Output voltage 95% of nominal Short circuit current (typ.) 125 125 125 125 125 125 125 % Iout Output voltage <250 mV No load to full load; nominal input MODULE INPUT SPECIFICATIONS Parameter 24 Vin 48 Vin 300 Vin 375 Vin Units Notes Undervoltage turn-on 17.5 34.9 175 243 Vdc Typical value Undervoltage turn-off 15.3 30.5 153 212 Vdc Typical value Overvoltage turn-off/on 37.8 78.8 N/A 446 Vdc Typical value Unit Notes Note: 300 Vin models do not have overvoltage turn-off. MODULE OUTPUT SPECIFICATIONS Parameter Min Line regulation Typ Max ±0.5 % Temperature regulation ±0.005 % / °C Power sharing accuracy ±5 % 10 to 100% of full load % Of nominal output voltage. For trimming below 90% of nominal, a minimum load of 10% of maximum rated power may be required. Programming range 10 110 Low line to high line; full load Over operating temperature range Note: For important information relative to applications where the converter modules are subject to continuous dynamic loading, contact Vicor applications engineering at 800-927-9474. Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715 FasTrak Mini E-Grade Family Set your site on VICOR at www.vicorpower.com Rev. 1.0 Page 2 of 8 ELECTRICAL CHARACTERISTICS, continued MODULE CONTROL SPECIFICATIONS Parameter Min Typ Max Unit Notes PRIMARY SIDE (PC = Primary Control; PR = Parallel) PC bias voltage current limit 5.50 1.5 5.75 2.1 6.00 3.0 Vdc mA PC current = 1.0 mA PC voltage = 5.5V PC module disable 2.3 2.6 2.9 Vdc Must be able to sink ≥4 mA. See Fig. 1 4 7 ms 0.5 Vavg UV, OV, OT, module fault. See Figs. 2 and 4 6.1 Volts PR load >30 ohms, < 30 pF PC module enable delay PC module alarm PR emitter amplitude 5.7 5.9 PR emitter current 150 PR receiver impedance 375 500 625 ohms 25°C PR receiver threshold 2.4 2.5 2.6 Volts Minimum pulse width: 20ns 12 modules Without PR buffer amplifier mA PR drive capability SECONDARY SIDE (SC = Secondary Control) SC bandgap voltage 1.21 1.23 1.25 Vdc SC resistance 990 1000 1010 ohms SC capacitance SC module alarm Referenced to –Sense 0.033 µF 0 Vdc With open trim; referenced to –Sense. See Fig. 6 Max Unit Notes 0.5 Vdc 0.25V per leg (senses must be closed) MODULE GENERAL SPECIFICATIONS Parameter Min Typ Remote sense (total drop) Isolation voltage (in to out) 3000 Vrms Complies with reinforced insulation requirements Isolation voltage (in to base) 1550 Vrms Complies with basic insulation requirements Isolation voltage (out to base) 500 Vrms Complies with operational insulation requirements Isolation resistance (in to out) 10 Weight Temperature limiting Agency Approvals 3.7 (104) 100 115 cULus, TÜV, CE megohms 4 (112) ounces (grams) °C See Figs. 2 and 4 UL60950, CSA0950, EN60950, IEC60950. With a fuse in series with the +Input Note: Specifications are subject to change without notice. The latest data sheets for individual models are available on the Vicor website at vicorpower.com. Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715 FasTrak Mini E-Grade Family Set your site on VICOR at www.vicorpower.com Rev. 1.0 Page 3 of 8 CONTROL FUNCTIONS - PC PIN Module Enable/Disable Module Alarm The module may be disabled by pulling PC below 2.3V with respect to the –Input. This may be done with an open collector transistor, relay, or optocoupler. Multiple converters may be disabled with a single transistor or relay either directly or via “OR’ing” diodes. See Figure 1. The module contains “watchdog” circuitry which monitors input voltage, operating temperature and internal operating parameters. In the event that any of these parameters are outside of their allowable operating range, the module will shut down and PC will go low. PC will periodically go high and the module will check to see if the fault (as an example, overtemperature) has cleared. If the fault has not been cleared, PC will go low again and the cycle will restart. The SC pin will go low in the event of a fault and return to its normal state after the fault has been cleared. See Figures 2 and 4. Primary Auxiliary Supply At 5.7V, PC can source up to 1.5mA. In the example shown in Figure 3, PC powers a module enabled LED. +In +In +Out SW1 +S PC PR 2-20ms typ. f (VIN) SW3 1K SC –S 5.7Vdc (0-3mA) –In –Out SW2 +Out +S 50Ω SW1, 2, & 3 shown in "Fault" position PR –S –In Auto Restart PC SC Disable Input Undervoltage Input Overvoltage Overtemperature Module Faults 1.23 Vdc 6K –Out Disable = PC <2.3V Figure 1—Module enable/disable. Figure 2—PC/SC module alarm logic. +In +Out PC "Module Enabled" Fault +S PC 40μs typ. 5.7V SC 4kΩ PR –S –In –Out SC Figure 3—LED on-state indicator. Optocoupler 1.23V Figure 4—PC/SC module alarm timing. +In +Out +In PC +S PC SC 4kW 2-20ms typ. +Out +S SC PR –S PR –S –In –Out –In –Out Figure 5—Isolated on-state indicator. Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715 Alarm 1.00V Figure 6—Secondary side on-state indicator. FasTrak Mini E-Grade Family Set your site on VICOR at www.vicorpower.com Rev. 1.0 Page 4 of 8 CONTROL FUNCTIONS - SC PIN Output Voltage Programming The output voltage of the converter can be adjusted or programmed via fixed resistors, potentiometers or voltage DACs. See Figures 7 and 8. +Out +Out +S +S Error Amp SC –S 1kΩ 0.033 μF RD Trim Down Load Error Amp SC RU Trim Up Load –S 1kΩ 0.033 μF –Out –Out 1.23V 1.23V RD (ohms) = 1,000 Vout Vnom - Vout RU (ohms) = 1,000 (Vout-1.23) Vnom 1.23 (Vout-Vnom) –1,000 Figure 7—Output voltage trim down circuit. Figure 8—Output voltage trim up circuit. Trim Down Trim Up 1. This converter is not a constant power device – it has a constant current limit. Hence, available output power is reduced by the same percentage that output voltage is trimmed down. Do not exceed maximum rated output current. 1. The converter is rated for a maximum delivered power. To ensure that maximum rated power is not exceeded, reduce maximum output current by the same percentage increase in output voltage. 2. The trim down resistor must be connected to the –Sense pin. 2. The trim up resistor must be connected to the +Sense pin. 3. Do not trim the converter above maximum trim range (typically +10%) or the output over voltage protection circuitry may be activated. Trim resistor values calculated automatically: On-line calculators for trim resistor values are available on the vicor website at: vicorpower.com/tools.html. Resistor values can be calculated for fixed trim up, fixed trim down and for variable trim up or down cases for both 1st and 2nd Generation DC-DC converters. In addition to trimming information, the web site and the Applications Manual also include design tips, applications circuits, EMC suggestions, thermal design guidelines and PDF data sheets for all available Vicor products. Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715 FasTrak Mini E-Grade Family Set your site on VICOR at www.vicorpower.com Rev. 1.0 Page 5 of 8 CONTROL FUNCTIONS - PR PIN Parallel Operation The PR pin supports paralleling for increased power with N+1 (N+M) redundancy and phased array capability. Modules of the same input voltage, output voltage, and power level will current share if all PR pins are suitably interfaced. Compatible interface architectures include the following: DC coupled single-wire interface. All PR pins are directly connected to one another. This interface supports current +Out +In PC +S PC Module 1 0.001µF SC PR –In PR –In –Out +In +Out +In +Out PC +S PC 0.001µF SC Module 2 PR –In +In Module N+1 PC PR –In +Out +S SC –S –Out +S Module 2 (up to 12) SC –S PR –S –In –Out –In –Out Ground plane Figure 10—AC coupled single-wire interface. • The +Out and –Out power buses should be designed to minimize and balance parasitic impedance from each module output to the load. +S –S +S Load –S –S +Out +S SC –S –Out –S PR +S +In PC SC –S Figure 9—DC coupled single-wire interface. PC +S Module 1 –Out Ground plane Module 1 +Out –In Module 2 (up to 12) +Out +S SC –S –Out AC coupled single-wire interface. All PR pins are connected to a single communication bus through 0.001µF (500V) capacitors. This interface supports current sharing and is fault tolerant except for the communication bus. See Figure 10. +In PR +In sharing but is not fault tolerant. Minus In pins must be tied to the same electric potential. See Figure 9. • The +Sense pins should be tied to the same point on the +Out power bus; the –Sense pins should be tied to the same point on the –Out power bus. • At the discretion of the power system designer, a subset of all modules within an array may be configured as slaves by shorting SC to –S. +In +Out +S PC SC PR –In –S –Out • OR’ing diodes may be inserted in series with the +Out pins of each module to provide module output fault tolerance. Figure 11—N+1 module array output connections. +Sense from other modules in the array Figure 12—OR’ing diodes connections. PIN STYLES * Designator Description Notes (None) Short solder Requires in-board, mounting L Long solder On-board mounting for 0.065" boards S Short ModuMate SurfMate or in-board socket mounting – RoHS compliant N Long ModuMate On-board socket mounting – RoHS compliant * Pin style designator follows the “B” after the output power and precedes the baseplate designator. Ex. V375A24C600BN — Long ModuMate Pins Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715 FasTrak Mini E-Grade Family Set your site on VICOR at www.vicorpower.com Rev. 1.0 Page 6 of 8 MECHANICAL DRAWINGS MODULE OUTLINE Converter Pins No. Function Label 1 +In + Primary 2 PC Control 3 Parallel PR 4 –In – 5 –Out – 6 8 9 0.01 style 2 & 3 baseplates only (4X)*** 0.300 ±0.015 7,62 ±0,38 –S Secondary Control +Sense +Out 2.20 55,9 1.74 44,2 0.23 (REF) 5,8 2.000 50,80 0.49 12,4 0.12* 0.20** 3,1 5,1 0.10 2,5 0.15 X 45˚ 3,81 CHAMFER Pin CL 1 0.300 ±0.015 7,62 ±0,38 SC 2 3 4 (ALL MARKINGS THIS SURFACE) 7 –Sense 0.50 ±0.02 12,7 ±0,5 +S + 0.35 (2X) 8,8 1.900 48,26 Pin CL 2.28 1.30 57,9 33,0 ALUMINUM BASEPLATE 0.65 16,5 FULL R (6X) 0.130 3,30 9 8 7 6 0.150 DIA,(2X) 3,81 0.080 DIA,(7X) 2,03 0.400 10,16 0.700 17,78 1.000 25,40 1.400 35,56 Slotted or (6X) 5 0.43 10,9 0.06 R (3X) 1,5 0.54 (9X) 13,7 Short Pin 0.62 (9X) 15,7 Long Pin Use a 4-40 Screw (6X) Torque to: 5 in-lbs .57 N-m 2.20 55,9 (REF.) Threaded 4-40 UNC-2B (6X) * ** *** CL or Thru Hole #30 Drill Thru (6X) (0.1285) Style 1 baseplate only Style 2 & 3 baseplates Reserved for Vicor accessories. Not for mounting Center line ALL MARKINGS THIS SURFACE PCB MOUNTING SPECIFICATIONS PCB THICKNESS R 0.062 ±0.010 1,57 ±0,25 PLATED THRU HOLE DIA 1.790 45,47 0.06 (4X) 1,5 ONBOARD SOLDER MOUNT SHORT PIN STYLE LONG PIN STYLE (7X) 0.094 ±0.003 2,39 ±0,08 0.094 ±0.003 2,39 ±0,08 (2X) 0.164 ±0.003 4,16 ±0,08 0.164 ±0.003 4,16 ±0,08 ALUMINUM BASEPLATE PINS STYLES SOLDER:TIN/LEAD HOT SOLDER DIPPED MODUMATE: GOLD PLATED COPPER 0.158 4,01 1 2 3 4 1.584* 40,23 1.900* 48.26 48,26 9 8 7 6 5 0.400* 10,16 0.43 10,9 0.700* 17,78 0.195 4,95 INBOARD SOLDER MOUNT 0.53 13,5 Unless otherwise specified, dimensions are in inches mm Decimals 1.000* 25,40 1.400* 35,56 0.XX * DENOTES ±0.003 TOL = ±0,08 Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715 Tol. Angles ±0.01 ±0.25 0.XXX ±1° ±0.005 ±0.127 FasTrak Mini E-Grade Family Set your site on VICOR at www.vicorpower.com Rev. 1.0 Page 7 of 8 Vicor’s comprehensive line of power solutions includes modular, high density DC-DC converters and accessory components, configurable power supplies, and custom power systems. Information furnished by Vicor is believed to be accurate and reliable. However, no responsibility is assumed by Vicor for its use. No license is granted by implication or otherwise under any patent or patent rights of Vicor. Vicor components are not designed to be used in applications, such as life support systems, wherein a failure or malfunction could result in injury or death. All sales are subject to Vicor’s Terms and Conditions of Sale, which are available upon request. Specifications are subject to change without notice. 45 Component Solutions for Your Power System Vicor Corporation 25 Frontage Road Andover, MA, USA 01810 Tel: 800-735-6200 978-470-2900 Fax: 978-475-6715 Email Vicor Express: [email protected] Technical Support: [email protected] Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715 FasTrak Mini E-Grade Family Set your site on VICOR at www.vicorpower.com Rev. 1.0 9/05