EURO QUARTZ EM32S Series TCXO Clipped Sinewave 3.2 x 2.5 x1.3mm SMD Ultra-miniature SMD package 3.2 x 2.5 x 1.3mm Stability from ±1ppm over -30° to +75°C Supply Voltage from 2.3 Volts to 5.5 Volts Produced as TCXO or VCTCXO with EFC Readily customized EM32S - OUTLINES AND DIMENSIONS DESCRIPTION EM32 series TCXOs are ceramic SMD TCXOs packaged in an industrystandard, ultra-miniature 3.2 x 2.5mm package. This TCXO can be run from a supply voltage of 2.3 to 5.5 Volts. Close tolerances from ±1ppm over -30° to +75°C are available. The part can be produced as either a standard TCXO or a voltage-controlled TCXO (VCTCXO). SPECIFICATION Product Series Code TCXO: VCTCXO: Frequency Range: Output Waveform: Initial Calibration Tolerance**: Standard Frequencies: EM32S VEM32S 16.0MHz to 40.0MHz* Clipped Sinewave <±1ppm at 25°C 10.0, 12.80, 13.0, 14.40, 15.36, 16.384, 19.2, 19.440, and 19.68MHz (Partial list) See table Operating Temperature Range: Frequency Stability vs. Ageing: vs. Voltage Change: vs. Load Change: vs. Reflow: ±1.0 ppm max. first year ±0.3 ppm max. ±5% change ±0.3 ppm max. ±10% change ±1ppm max. for one reflow (Measured after 24 hours) +2.8, +3.0 or +5.0Volts (Specify when ordering) 0.8V p-p minimum 2ms typical, 5ms max. See table below 10kOhm//10pF ±10% -10dB typical, -7dB max. See table DC block, AC coupled -50° to +100°C Supply Voltage: Output Voltage Level: Start-up Time: Current Consumption: Output Load: Harmonic Distortion: SSB Phase Noise: Output Format: Storage Temperature: * Note: The frequency range between 26MHz to 40MHz is only available for 2.8 Volt and 3.0 Volt supply voltages. ** Stability over temperature is measured from this initial frequency. FREQUENCY STABILITY P ±0.5 ±1.0 ±1.5 ±2.0 ±2.5 0 ~ +50 ASK P P P P -10 ~ +60 x P P P P -20 ~ +70 x x P P P -30 ~ +75 x x x P PP -40 ~ +85 x x x x P = available, x = not available, ASK = call Technical Sales CURRENT CONSUMPTION Supply Voltage Frequency Range Control Voltage: Standard = +1.5±1.0Volts for all input voltages. (Contact technical sales if +2.5±2.0 Volts is required.) Frequency Deviation: ±6.0 ppm min. Slope Polarity: Positive (increase of control voltage increases output frequency.) Input Impedance: 1.0M min. Modulation Bandwidth: 3.0kHz min. measured at -3dB Linearity: 10% max. PHASE NOISE SSB Phase Noise at 25°C Frequency Stability (ppm) Temperature Range (°C) VEM32S VOLTAGE CONTROL SPECIFICATION Max Current 9.6 to 15MHz 1.5mA 15.01 to 26MHz 2.0mA 26.01 to 40MHz 2.5mA Offset (Hz) 10 100 1k 10k 100k EM32S 13MHz (dBc/Hz) -80 -115 -135 -148 -150 PART NUMBERING PROCEDURE Example: EM32S3-40.00-2.5/-30+75 Series Description TCXO = EM32S VCTCXO = VEM32S Supply Voltage 28 = 2.8 VDC 3 = 3.0 VDC 5 = 5.0 VDC Frequency (MHz) Stability over OTR (±ppm) Operating Temperature Range (OTR) (°C) Lower and upper limits. EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 [email protected] www.euroquartz.co.uk