rev. PART NUMBER: VPOL20A-12W-SIP page 1 of 14 date 08/2007 DESCRIPTION: point of load converter features * industry standard pin out * high efficiency to 94% * 300 KHz switching frequency * 6.0-14 VDC wide input range * 0.75-5.0 VDC wide output range * over temperature protection * continuous short circuit protection * remote on/off * cost-efficient open frame design * UL/C-UL60950 certified * output voltage sequencing (tracking) * power good signal 1. INTRODUCTION 2. VPOL20A-12W-SIP CONVERTER FEATURES 6. SAFETY 6.1 Input Fusing and Safety Considerations. 3. GENERAL DESCRIPTION 3.1 Electrical Description 7. APPLICATIONS 7.1 Layout Design Challenges. 3.2 Thermal Packaging and Physical Design. 7.2 Convection Requirements for Cooling 4. TECHNICAL SPECIFICATIONS 7.3 Thermal Considerations 5. MAIN FEATURES AND FUNCTIONS 5.1 Operating Temperature Range 7.4 Power De-Rating Curves 5.2 Over-Temperature Protection (OTP) 7.6 Input Capacitance at the Power Module 5.3 Output Voltage Adjustment 7.7 Test Set-Up 5.4 Safe Operating Area (SOA) 7.8 Remote Sense Compensation 5.5 Over Current Protection 7.9 VPOL20A-12W-SIP Series Output Voltage Adustment. 5.6 Remote ON/OFF 7.10 Output Ripple and Noise Measurement 5.7 UVLO (Under-Voltage Lockout) 7.11 Output Capacitance 5.8 Output Voltage Sequencing (Tracking) 7.5 Efficiency vs Load Curves 8. MECHANICAL OUTLINE DIAGRAMS 8.1 VPOL20A-12W-SIP Mechanical Outline Diagrams 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2382 rev. page 2 of 14 date 08/2007 DESCRIPTION: point of load converter PART NUMBER: VPOL20A-12W-SIP converter is also protected against over-temperature conditions. If the converter is overloaded or the ambient temperature gets too high, the 1. Introduction converter will shut down to protect the unit. This application note describes the features and functions of V-Infinity’s VPOL20A-12W-SIP series of Non Isolated DC-DC Converters. These L1 Q1 +VIN +VO are highly efficient, reliable and compact, high power density, single output DC/DC converters. These “Point of Load” modules serve the C1 needs specifically of the fixed and mobile telecommunications and Q2 D1 R sense C2 +SENSE computing market, employing economical distributed Power Architectures. The VPOL20A-12W-SIP series provide precisely regulated output voltage range from 0.7525V to 5.0Vdc over a wide COM COM range of input voltage (Vi=6.0 – 14Vdc) and can operate over an ambient temperature range of –40 to +85. Ultra- high efficiency operation is achieved through the use of synchronous rectification and drive control techniques. R1 PGood ON/OFF PWM IC ERR AMP SEQ R trim TRIM R2 The modules are fully protected against short circuit and overtemperature conditions. V-Infinity’s world class automated Figure 1. Electrical Block Diagram manufacturing methods, together with an extensive testing and qualification program, ensure that all VPOL20A-12W-SIP series converters are extremely reliable. 3.2 Thermal Packaging and Physical Design. 2. VPOL20A-12W-SIP Converter Features The VPOL20A-12W-SIP series uses a multi-layer FR4 PCB construction. All surface mount power components are placed on one High efficiency topology, typically 94% at 5.0Vdc side of the PCB, and all low-power control components are placed on Industry standard footprint the other side. Thus, the Heat dissipation of the power components is Wide ambient temperature range, -40C to +85C optimized, ensuring that control components are not thermally stressed. Cost efficient open frame design The converter is an open-frame product and has no case or case pin. Programmable output voltage via external resistor from 0.7525 to The open-frame design has several advantages over encapsulated 5.0Vdc closed devices. Among these advantages are: No minimum load requirement (Stable at all loads) Remote ON/OFF Efficient Thermal Management: the heat is removed from the Remote sense compensation heat generating components without heating more sensitive, small Fixed switching frequency signal control components. Continuous short-circuit protection and over current protection Environmental: Lead free open-frame converters are more easily Over-temperature protection (OTP) re-cycled. Monotonic Startup with pre-bias at the output. Cost Efficient: No encapsulation. Cost efficient open-frame UL/IEC/EN60950 Certified. construction. Reliable: Efficient cooling provided by open frame construction offers high reliability and easy diagnostics. Output Voltage Sequencing( Tracking ) Power Good Signal (Option) 3. General Description 3.1 Electrical Description A block diagram of the VPOL20A-12W-SIP Series converter is shown in Figure 1. Extremely high efficiency power conversion is achieved through the use of synchronous rectification and drive techniques. Essentially, the powerful VPOL20A-12W-SIP series topology is based on a non-isolated synchronous buck converter. The control loop is optimized for unconditional stability, fast transient response and a very tight line and load regulation. In a typical pre-bias application the VPOL20A-12W-SIP series converters do not draw any reverse current at start-up. The output voltage can be adjusted from 0.7525 to 5.0vdc, using the TRIM pin with a external resistor. The converter can be shut down via a remote ON/OFF input that is referenced to ground. This input is compatible with popular logic devices; a 'positive' logic input is supplied as standard. Positive logic implies that the converter is enabled if the remote ON/OFF input is high (or floating), and disabled if it is low. The 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2382 rev. page 3 of 14 date 08/2007 DESCRIPTION: point of load converter PART NUMBER: VPOL20A-12W-SIP 4. Technical Specifications (All specifications are typical at nominal input, full load at 25°C unless otherwise noted.) PARAMETER ABSOLUTE MAXIMUM RATINGS Input Voltage Continuous Operating Temp erature See Thermal Considerations Section NOTES and CONDITIONS Device Min. Typical Max. Units ALL 0 16 Vdc ALL -40 +85 °C ALL -55 +125 °C ALL 6.0 6.5 14 14 Vdc Storage Temperature INPUT CHARACTERISTICS Operating Input Voltage Vo=4.5V Vo=5.0V Input Under-Voltage Lockout Turn-On Voltage Threshold Turn-Off Voltage Threshold Lockout Hysteresis Voltage 12 12 5.0 ALL ALL ALL ALL Vdc Vdc Vdc 4.0 1.0 Maximum Input Current Vin=0 to 14Vdc , Io=Io,max. No-Load Input Current Vo=0.7525V Vo=1.2V Vo=1.5V Vo=1.8V Vo=2.0V Vo=2.5V Vo=3.3V Vo=5.0V ALL Off Converter Input Current Shutdown input idle current ALL 10 mA ALL 0.4 As 2 Inrush Current (I t) 19 40 50 50 50 60 65 75 95 A mA 2 P-P thru 1uH inductor, 5Hz to 20MHz ALL 220 mA Output Voltage Set Point Vin=Nominal Vin , Io=Io.max, Tc=25 ALL -1.5% Vo,set +1.5% Vdc Output Voltage Trim Adjustment Range Selected by an external resistor ALL 0.7525 5.0 Vdc Io=Io.min to Io.max ALL -0.5 +0.5 % Input Reflected-Ripple Current OUTPUT CHARACTERISTIC Output Voltage Regulation Load Regulation Vin=low line to high line ALL -0.2 +0.2 % Tempera ture Coefficient Line Regulation Ta=-40 °C to 85°C ALL -0.03 +0.03 %/°C Output Voltage Ripple and Noise 5Hz to 20MHz bandwidth Peak-to-Peak Full Load, 1uF ceramic and 10uF tantalum ALL 75 mV RMS Full Load, 1uF ceramic and 10uF tantalum ALL 30 mV Low ESR ALL 8000 uF External Capacitive Load Operating Output Current Range Output DC Current-Limit Inception Output Voltage =90% Nominal Output Voltage Shout Circuit Protection Continuous with Hiccup Mode Sequency Slew Rate Capability dVSEQ/dt ALL 0 ALL 24 0.1 Sequencing Delay Time 30 20 A 36 A 1.0 10 Tracking Accuracy Power up Power down Power Good Signal Asserted Logic High Vo ALL Suffix “P” V/ms ms 90 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2382 200 400 mV 110 % rev. page 4 of 14 date 08/2007 DESCRIPTION: point of load converter PART NUMBER: VPOL20A-12W-SIP Error Brand 50% Step Load Change, di/dt=2.5A/us ALL 200 mV Setting Time (within 1% Vout nominal) 50% Step Load Change, di/dt=2.5A/us ALL 200 us EFFICIENCY 100% Load Vo=0.7525V Vo=1.2V Vo=1.5V Vo=1.8V Vo=2.0V Vo=2.5V Vo=3.3V Vo=5.0V ALL Non-isolation ALL 78 84 87 88 89 90 92 94 % ISOLATION CHARACTERISTICS Input to Output 0 Vdc FEATURE CHARACTERISTICS Switching Frequency ON/OFF Control, Positive Logic Remote On/Off Logic Low (Module Off) Logic High (Module On) ALL KHz VPOL20A-12W-SIP 0 0.4 Vin Vdc Vdc VPOL20A-12W-SIP 0 2.8 0.4 Vin Vdc Vdc 1 1 mA mA or Open Circuit ON/OFF Control, Negative Logic Remote On/Off Logic Low (Module On) or Open Circuit Logic High (Module Off) ON/OFF Current (for both remote on/off logic) Leakage Current (for both remote on/off logic) Turn-On Delay and Rise Time Turn-On Delay Time, From On/Off Control Turn-On Delay Time, From Input Output Voltage Rise Time Over Temperature Protection 300 Ion/off at Von/off =0.0V Logic High, Von/off=14V ALL ALL Von/off to 10%Vo,set Vin,min. to 10%Vo,set 10%Vo,set to 90%Vo,set ALL ALL ALL ALL 3 3 4 130 ms ms ms ALL 0.9 M hours ALL 11 grams °C GENERAL SPECIFICATIONS Io=100%of Io.max;Ta=25 217F MTBF Weight Dimensions 2.4x0.51 per MIL-HDBK- x0.327 inches (61x12.95x8.3 mm) 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2382 rev. page 5 of 14 date 08/2007 DESCRIPTION: point of load converter PART NUMBER: VPOL20A-12W-SIP 5. Main Features and Functions removed. The power module will supply up to 150% of rated current. In 5.1 Operating Temperature Range protection. V-Infinity’s VPOL20A-12W-SIP series converters highly efficient 5.6 Remote ON/OFF the event of an over current converter will go into a hiccup mode converter design has resulted in its ability to operate over a wide ambient temperature environment ( -40°C to 85°C). Due consideration must be given to the de-rating curves when ascertaining maximum power that can be drawn from the converter. The maximum power drawn is influenced The remote ON/OFF input feature of the converter allows external circuitry to turn the converter ON or OFF. Active-high remote ON/OFF is available as standard. The VPOL20A-12W-SIP is turned on if the remote ON/OFF pin is high(=Vin), or left open. Setting the pin low(<0.4Vdc) will by a number of factors, such as: turn the converter ‘Off’. The signal level of the remote on/off input is Input voltage range. defined with respect to ground. If not using the remote on/off pin, leave Output load current. Air velocity (forced or natural convection). Mounting orientation of converter PCB with respect to the Airflow. Motherboard PCB design, especially ground and power planes. These can be effective heat sinks for the converter. the pin open (module will be on). The part number suffix “N” is Negative remote ON/OFF version. The unit is guaranteed OFF over the full temperature range if this voltage level exceeds 2.8Vdc. The converters are turned on If the on/off pin input is low (<0.4Vdc) or left open. The recommended remote on/off drive circuit as shown as figure 3, 4. 5.2 Over-Temperature Protection (OTP) The VPOL20A-12W-SIP Series converters are equipped with non- +Vin latching over-temperature protection. A temperature sensor monitors the +Vo temperature of the hot spot (typically, top switch). If the temperature exceeds a threshold of 130°C (typical) the converter will shut down, disabling the output. When the temperature has decreased the converter ON/OFF Control Remote ON/OFF Q1 will automatically restart. VPOL20A-12W-SIP The over-temperature condition can be induced by a variety of reasons such as external overload condition or a system fan failure. Common Common 5.3 Output Voltage Adjustment Section 7.8 describes in detail as to how to trim the output voltage with Figure 3. Positive Remote ON/OFF Input Drive Circuit respect to its set point. The output voltage on all models is trimmable in the range 0.7525 – 5.0Vdc. +Vo +Vin 5.4 Safe Operating Area (SOA) Q1 VPOL20A-12W-SIP Figure 2 provides a graphical representation of the Safe Operating Area (SOA) of the converter. This representation assumes ambient operating conditions such as airflow are met as per thermal guidelines provided in ON/OFF Control Remote ON/OFF Sections 7.2 and 7.3. Common Vo Common Figure 4. Negative Remote ON/OFF Input Drive Circuit VOLTAGE (V) Vo,nom Safe Operating Area Io,max Io,CL Io CURRENT (A) Figure 2. Maximum Output Current Safe Operating Area 5.5 Over Current Protection All different voltage models have a full continuous short-circuit protection. The unit will auto recover once the short circuit is removed. To provide protection in a fault condition, the unit is equipped with internal overcurrent protection. The unit operates normally once the fault condition is 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2382 rev. page 6 of 14 date 08/2007 DESCRIPTION: point of load converter PART NUMBER: VPOL20A-12W-SIP Power start up with SEQ signal Input Voltage=12Vdc Master DC/DC output voltage (CH1) = 5Vdc Salve DC/DC output voltage (CH2)=3.3Vdc Sequencing voltage= 0.67V/msec 5.7 UVLO (Under-Voltage Lockout) The voltage on the Vcc pin determines the start of the operation of the Converter. When the input Vcc rises and exceeds about 5.0V the converter initiates a soft start. The UVLO function in the converter has a hysteresis (about 1V) built in to provide noise immunity at start-up. 5.8 Output Voltage Sequencing (Tracking) The VPOL20A-12W-SIP series including a sequencing feature. It is able implement various types of output voltage sequencing in customer applications, VPOL20A-12W-SIP series is accomplishable through an additional sequencing pin. When not using the sequencing feature, tie the SEQ pin to +Vin. When the signal voltage is applied to the SEQ pin, the output voltage tracks this voltage until the output reaches the set point voltage. The SEQ voltage needs to be set higher than the set point of the module. The output voltage will be follow by the voltage on the SEQ pin. On the multiple modules application, we can connect SEQ pin and input signal voltage together to apply on the SEQ pin. Customers can get multiple modules to track their output voltages to follow the voltage of the SEQ pin. To control this module for sequen cing, when the input voltage Figure 6. Example testing circuit of sequencing function applied to the module. The on/off pin is left unconnected so that the module is ON by default. After applying input voltage to the module, a minimum of 10msec delay is required before applying voltage on the SEQ pin and slew rate of the voltage on the SEQ pin see technical Power turn off with SEQ signal voltage Input Voltage=12Vdc (CH1) Master DC/DC output voltage (CH2) = 5Vdc Salve DC/DC output voltage (CH3)=3.3Vdc specifications “ dVSEQ/dt “. After 10msec delay, an Analog voltage is applied to the SEQ pin and the output voltage of the module will track this voltage until output voltage reaches the set point voltage. To initiate simultaneous shutdown of the modules, the SEQ pin voltage is lowered in a controlled manner. Output voltage of the modules track the voltages below their set-point voltage voltages. A valid input voltage must be maintained until the tracking and output voltages reach ground potential to ensure a controlled shutdown of the modules. A typical example testing circuit used master DC/DC converter and VPOL20A-12W-SIP Module as shown as below: +Vin Power + C1 +Vo CH1 R1 Load Master DC/DC Converter Supply Common Common Figure 7. Example testing circuit of sequencing function +Vin +Vo SEQ CH2 VPOL20A-12W-SIP Common C2 Common Figure 5. Example testing circuit of sequencing function R2 CH3 6. Safety Load 6.1 Input Fusing and Safety Considerations. Agency Approvals: The power Supply shall be submitted to and receive formal approval from the following test agencies. 1.The power supply shall be approved by a nationally recognized testing rd laboratory to UL/CSA 60950 3 Edition (North America) and EN60950 (International) 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2382 rev. 2. CB Certificate from an internationally recognized test house in accordance with EN 60950. The VPOL20A-12W-SIP series converters do not have an internal fuse. However, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a time-delay fuse with a maximum rating of 25A. 7.1 Layout Design Challenges. In optimizing thermal design the PCB is utilized as a heat sink. Also some heat is transferred from the VPOL20A-12W-SIP module to the main board through connecting pins. The system designer or the end user must ensure that other components and metal in the vicinity of the VPOL20A-12W-SIP series meet the spacing requirements to which the system is approved. Low resistance and low inductance PCB layout traces are the norm and should be used where possible. Due consideration must also be given to proper low impedance tracks between power module, input and output grounds. The recommended VPOL20A-12W-SIP footprint as shown as figure 8. LAYOUT PAT TERN TOP VIEW All Dimmension In Inches(mm) Tolerance : .XX=¡ Ó0.02 ( .X=¡ Ó0.5 ) .XXX=¡ Ó0.010 ( .XX=¡ Ó0.25 ) 7 of 14 date 08/2007 DESCRIPTION: point of load converter PART NUMBER: VPOL20A-12W-SIP 0.29(7.4) page 0.33(8.4) 1.1mm PLATED THROUGH HOLE 1.6mm PAD SIZE Figure 8. Recommended VPOL20A-12W-SIP Footprint 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2382 rev. page 8 of 14 date 08/2007 DESCRIPTION: point of load converter PART NUMBER: VPOL20A-12W-SIP 7. Applications 7.2 Convection Requirements for Cooling To predict the ap proximate cooling needed for the module, refer to the Power De-rating curves in Figure 11. These de -rating curves are Figure 10. Temperature Measurement Location for approximations of the ambient temperatures and airflows required to VPOL20A-12W-SIP keep the power module temperature below its maximum rating. Once the module is assembled in the actual system, the module’s temperature should be checked as shown in Figure 9 to ensure it does not exceed 7.3 Thermal Considerations 120°C. The power module operates in a variety of thermal environments; Proper cooling can be verified by measuring the power module’s however, sufficient cooling should be provided to help ensure reliable temperature at “ Tref ” as shown in Figure 10. operation of the unit. Heat is removed by conduction, convection, and radiation to the surrounding environment. The thermal data presented is Wind Tunnel based on measurements taken in a set-up as shown in Figure 9. Figure 25.4(1.0) 11 represents the test data. Note that the airflow is parallel to the long axis of the module as shown in Figure7 for the VPOL20A-12W-SIP. PWBs The temperature at “ Tref ” location should not exceed 120 °C. The output power of the module should not exceed the rated power for the module (VO, set x IO, max). The thermal data presented is based on measurements taken in a wind tunnel. The test setup shown in Figure 7 Power Module and EUT need to solder on 53.8mm x 43.2mm(2.12'' x 1.7'') test pcb. Note that airflow is parallel to the long axis of the module as shown in Fig10. 76.2(3.0) Thermocuple Location for measuring ambient temperature and airflow 12.7(0.5) Air flow Note : Dimensions are in millimeters and (inches) Figure 9. Thermal Test Setup 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2382 rev. TYPICAL POWER DERATING FOR 5 Vin 3.3 Vout 25.0 Output Current(A) 20.0 15.0 0LFM 100LFM 200LFM 300LFM 400LFM 5.0 0.0 0 10 20 30 40 50 60 9 of 14 date 08/2007 DESCRIPTION: point of load converter PART NUMBER: VPOL20A-12W-SIP 10.0 page 70 80 90 100 Ambient Temperature( oC) NOTE: 1. specific input & output derating curves available, please contact V-Infinity for detail 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2382 rev. PART NUMBER: VPOL20A-12W-SIP page 10 of 14 date 08/2007 DESCRIPTION: point of load converter 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2382 rev. VPOL20A-12W-SIP Vo=1.8V (Eff Vs Io) date 08/2007 VPOL20A-12W-SIP Vo=1.5V (Eff Vs Io) 100% 95% 95% Efficincy (%) 100% Efficincy (%) 11 of 14 DESCRIPTION: point of load converter PART NUMBER: VPOL20A-12W-SIP 90% 85% 6.0V 12V 14V 80% 75% 90% 85% 6.0V 12V 14V 80% 75% 70% 70% 0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 Current Load (A) 8 10 12 14 16 18 20 Current Load (A) VPOL20A-12W-SIP Vo=0.75V (Eff Vs Io) VPOL20A-12W-SIP Vo=1.2V (Eff Vs Io) 100% 95% 95% 90% 90% Efficincy (%) 100% Efficincy (%) page 85% 80% 75% 6.0V 12V 14V 70% 65% 85% 80% 75% 6.0V 12V 14V 70% 65% 60% 60% 0 2 4 6 8 10 12 Current Load (A) 14 16 18 20 0 2 4 6 8 10 12 Current Load (A) 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2382 14 16 18 20 rev. page 12 of 14 date 08/2007 DESCRIPTION: point of load converter PART NUMBER: VPOL20A-12W-SIP Line.reg = 7.6 Input Capacitance at the Power Module VHL _ VLL x100 % VLL Where: VHL is the output voltage of maximum input voltage at full load. The VPOL20A-12W-SIP converters must be connected to a low AC VLL is the output voltage of minimum input voltage at full load. source impedance. To avoid probl ems with loop stability source inductance should be low. Also, the input capacitors should be placed Current Meter close to the converter input pins to de-couple distribution inductance. A +Vin handling capability. Low ESR polymers are a good choice. They have Power high capacitance, high ripple rating and low ESR (typical <100mohm). Supply A +Vo However, the external input capacitors are chosen for suitable ripple +Sense + V 100uF VPOL20A-12W-SIP Voltage Meter V Load Electrolytic capacitors should be avoided. Circuit as shown in Figure 12 Common represents typical measurement methods for ripple current. Input Common reflected-ripple current is measured with a simulated source Inductance of 1uH. Current is measured at the input of the module. Figure 13. VPOL20A-12W-SIP Series Test Setup 7.8 Remote Sense Compensation To Oscilloscope L1 +Vin 1uH Power + minimizes the effects of distribution losses such as drops across the 2*100uF Tantalum Supply Remote Sense regulates the output voltage at the point of load. It +Vo connecting pin and PCB tracks (see Figure 14). Please note however, R1 VPOL20A-12W-SIP C2 1000uF Electronlyic ESR<0.1ohm Load the maximum drop from the output pin to the point of load should not exceed 500mV for remote compensation to work. Com Com The amount of power delivered by the module is defined as the output voltage multiplied by the output current (VO x IO). When using TRIM UP, the output voltage of the module will increase Figure 12. Input Reflected-Ripple Test Setup 7.7 Test Set-Up which, if the same output current is maintained, increases the power output by the module. Make sure that the maximum output power of the module remains at or below the maximum rated power. The basic test set-up to measure parameters such as efficiency and When the Remote Sense feature is not being used, leave sense pin load regulation is shown in Figure 13. Things to note are that this disconnected. converter is non-isolated, as such the input and output share a common ground. These grounds should be connected together via low Figure 14. Circuit Configuration for Remote Sense Operation impedance ground plane in the application circuit. When testing a converter on a bench set-up, ensure that -Vin and -Vo are connected together via a low impedance short to ensure proper efficiency and load regulation measurements are being made. When testing the V-Infinity’s VPOL20A-12W-SIP series under any transient conditions please ensure that the transient response of the source is sufficient to power the equipment under test. We can calculate the Efficiency Distribution Losses +Vin +Vo +Sense Load regulation and line regulation. The value of efficiency is defined as: VPOL20A-12W-SIP R-Load Vo x Io x100% ç= Vin x Iin Common Where: Vo is output voltage, Common Distribution Losses Io is output current, Vin is input voltage, Iin is input current. The value of load regulation is defined as: Load .reg = VFL _ VNL x100% VNL Where: VFL is the output voltage at full load VNL is the output voltage at no load The value of line regulation is defined as: 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2382 rev. page 13 of 14 date 08/2007 DESCRIPTION: point of load converter PART NUMBER: VPOL20A-12W-SIP 7.9 VPOL20A-12W-SIP Series Output Voltage Adustment. The output Voltage of the VPOL20A-12W-SIP can be adjusted in the range 0.7525V to 5.0V by connecting a single resistor on the motherboard (shown as Rtrim) in Figure 15. When Trim resistor is not COPPER STRIPS VO 10uF Power C1 SCOPE 1uF LOAD COM Supply + VIN connected the output voltage defaults to 0.7525V VPOL20A-12W-SIP +Vin +Vo Figure 16. Output Voltage Ripple and Noise Measurement Set-Up 7.11 Output Capacitance Trim R-Load VPOL20A-12W-SIP R trim-up Common Common V-Infinity’s VPOL20A-12W-SIP series converters provide unconditional stability with or without external capacitors. For good transient response low ESR output capacitors should be located close to the point of load. For high current applications point has already been made in layout considerations for low resistance and low inductance tracks. Output capacitors with its associated ESR values have an impact on Figure 15. Trim-up Voltage Setup The value of Rtrim-up defined as: Rtrim = ( loop stability and bandwidth. V-Infinity’s converters are designed to work with load capacitance up-to 8,000uF. It is reco mmended that any 10500 _ 1000 ) Vo _ 0.7525 additional capacitance, typically 1,000uF and low ESR (<20mohm), be connected close to the point of load and outside the remote compensation point. Where: is the external resistor in ohm, Rtrim-up Vo is the desired output voltage To give an exa mple of the above calculation, to set a voltage of 3.3Vdc, Rtrim is given by: Rtrim = ( 10500 _ 1000 ) _ 3.3 0.7525 Rtrim = 3.122K ohm For various output values various resistors are calculated and provided in Table 3 for co nvenience. Vo,set (V) 0.7525 1.2 1.5 1.8 2.0 2.5 3.3 5.0 Rtrim (Kohm) Open 22.46 13.05 9.024 7.417 5.009 3.122 1.472 Table 3 – Trim Resistor Values 7.10 Output Ripple and Noise Measurement The test set-up for noise and ripple measurements is shown in Figure 16. a coaxial cable with a 50ohm termination was used to prevent impedance mismatch reflections disturbing the noise readings at higher frequencies. The Output Ripple & Noise is measured with 1uf ceramic and 10uf tantalum. The measured position are 50mm to 75mm(2” to 3”) from the module. The “C1” is 200uF Tant alum capacitor ESR< 25m 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2382 rev. 8. Mechanical Outline Diagrams 8.1 VPOL20A-12W-SIP Mechanical Outline Diagrams Dimensions are in millimeters and inches Tolerance: x.xx ±0.02 in. (0.5mm) , x.xxx ±0.010 in. (0.25 mm) unless otherwise noted SIZE SIP 0.327(8.30)max. 0.23(5.8) 2.40(61.0) 6 7 8 9 10 11 12 1 2 3 4 5 0.510(12.95) 0.100(2.54) 0.025(0.64) 0.010(0.25) min. 0.250(6.35) 0.900(22.90) 0.28(7.1) 0.025(0.64) 0.400(10.20) 0.29(7.4) LAYOUT PAT TERN TOP VIEW All Dimmension In Inches(mm) Tolerance : .XX=¡ Ó0.02 ( .X=¡ Ó0.5 ) .XXX=¡ Ó0.010 ( .XX=¡ Ó0.25 ) 14 of 14 date 08/2007 DESCRIPTION: point of load converter PART NUMBER: VPOL20A-12W-SIP 0.14(3.6) page 0.33(8.4) 1.1mm PLATED THROUGH HOLE 1.6mm PAD SIZE PIN CONNECTION Pin FUNCTION +Output 1 +Output 2 3 +Sense +Output 4 5 Common No Pin / PGood 6 Common 7 +V Input 8 +V Input 9 10 Sequency 11 Trim 12 On/Off Control Figure 17 VPOL20A-12W-SIP Mechanical Outline Diagram 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2382