PTQA430025, PTQA430033 www.ti.com SLTS261 – MAY 2006 100-W 48-V INPUT ISOLATED DC/DC CONVERTER FEATURES • • • • • • • • • • • • • • The PTQA4300xx series operates from a standard 48-V telecom central office (CO) supply and occupies only 3.3 in2 of PCB area. The modules offer OEMs a compact and flexible high-output power source in an industry standard footprint. They are suitable for distributed power applications in both telecom and computing environments, and may be used for powering high-end microprocessors, DSPs, general purpose logic and analog. 100-W Output Input Voltage Range: 36 V to 75 V 92% Efficiency 1500 Vdc Isolation Fast Transient Response On/Off Control Overcurrent Protection Differential Remote Sense Adjustable Output Voltage Output Overvoltage Protection Over-Temperature Shutdown Undervoltage Lockout Standard 1/4-Brick Footprint UL Safety Agency Approval Features include a remote On/Off control with optional logic polarity, an undervoltage lockout (UVLO), a differential remote sense, and an industry standard output voltage adjustment using an external resistor. Protection features include output overcurrent protection (OCP), overvoltage protection (OVP), and thermal shutdown (OTP). The modules are fully integrated for stand-alone operation, and require no additional components. DESCRIPTION The PTQA4300xx series of power modules are single-output isolated DC/DC converters, housed in an industry standard quarter-brick package. These modules are rated up to 100W with a maximum load current of 30 amps. STANDARD APPLICATION SENSE (+) +VO 7 +VI Sense(+) 1 +V I CI (Optional) 3 −VI +VO PTQA430xxxN Adjust −VI Remote On/Off 2 −VO Sense(−) 8 6 CO (Optional) 4 L O A D −VO 5 SENSE (–) Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2006, Texas Instruments Incorporated PTQA430025, PTQA430033 www.ti.com SLTS261 – MAY 2006 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. ORDERING INFORMATION For the most current package and ordering information, see the Package Option Addendum at the end of this datasheet, or see the TI website at www.ti.com. PART NUMBERING SCHEME PTQA Input Voltage Output Current Output Voltage Enable Electrical Options 4 30 033 N 2 4 = 48 V 30 = 30A 025 = 2.5 V N = Negative 033 = 3.3 V P = Positive 2 = VO Adjust Pin Style A D D = Through-hole, Pb-free S = SMD, SnPb solder ball Z = SMD, SnAgCu solder ball ABSOLUTE MAXIMUM RATING UNIT TA VI, MAX PO, Operating Temperature Range Maximum Input Voltage –40°C to 85°C (1) Over VI Range Continuous voltage 80 V Peak voltage for 100 ms duration 100 V Maximum Output Power 100 W MAX TS Storage Temperature –40°C to 125°C Mechanical Shock Per Mil-STD-883, Method 2002.3 1 ms, 1/2 Sine, mounted Mechanical Vibrarion Per Mil-STD-883, Method 2007.2 20-2000 Hz, PCB mounted Weight Flammability (1) 2 AD Suffix 250 G AS or AZ Suffix 175 G AD Suffix 15 G AS or AZ Suffix 2.5 G 30 grams Meets UL 94V-O See SOA curves or consult factory for appropriate derating. Submit Documentation Feedback PTQA430025, PTQA430033 www.ti.com SLTS261 – MAY 2006 ELECTRICAL CHARACTERISTICS PTQA430025 (Unless otherwise stated, TA =25°C, VI = 48 V, VO = 2.5 V, CO = 0 µF, and IO = IOmax) PARAMETER TEST CONDITIONS MIN IO Output Current Over VI range 0 VI Input Voltage Range Over IO Range 36 VO tol Set Point Voltage Tolerance TYP 48 V ±1.15 %VO Regline Line Regulation Over VI range ±5 Regload Load Regulation Over IO range ±5 ∆Votot Total Output Voltage Variation Includes set-point, line, load, –40°C >TA > 85°C ∆VADJ Output Adjust Range PO≤ 75 W η Efficiency IO = 50% IOmax VR VO Ripple (pk-pk) 20 MHz bandwidth Transient Response A 75 %VO –40°C >TA > 85°C ∆Vtr UNIT 30 ±1 (1) Regtemp Temperature Variation ttr MAX ±1.5 –20 mV mV ±3 %VO 10 %VO 91% 50 mVpp 150 µs VO over/undershoot 25 mV 41 A 0.1 A/µs slew rate, 50% to 75% IOmax ITRIP Overcurrent Threshold Shutdown, followed by auto-recovery OVP Output Overvoltage Protection Output shutdown and latch off 120 %VO OTP Over Temperature Protection Temperature Measurement at thermal sensor. Hysteresis = 10°C nominal. 105 °C fs Switching Frequency Over VI range 300 kHz UVLO Undervoltage Lockout VOFF VI decreasing, IO = 6 A 32.5 VHYS Hysteresis 1.5 V On/Off Input: Negative Enable VIH Input High Voltage VIL Input Low Voltage IIL Input Low Current Referenced to –VI 2.4 Open (2) –0.2 0.8 –0.3 V mA On/Off Input: Positive Enable 4.5 Open (2) –0.2 0.8 VIH Input High Voltage VIL Input Low Voltage IIL Input Low Current –0.5 mA IISB Standby Input Current Output disabled (pin 2 status set to Off) 3 mA CI Internal Input Capacitance Between +VI and –VI 3 µF CO External Output Capacitance Between +VO and –VO Isolation Voltage Input-to-output and input-to-case Isolation Capacitance Input-to-output Isolation Resistance Input-to-output (1) (2) Referenced to –VI 0 30000 1500 V µF Vdc 1200 10 pF MΩ If Sense(–) is not used, pin 5 must be connected to pin 4 for optimum output voltage accuracy. The Remote On/Off input has an internal pull-up and may be controlled with an open collector (drain) interface. An open circuit correlates to a logic high. Consult the application notes for interface considerations. Submit Documentation Feedback 3 PTQA430025, PTQA430033 www.ti.com SLTS261 – MAY 2006 ELECTRICAL CHARACTERISTICS PTQA430033 (Unless otherwise stated, TA =25°C, VI = 48 V, VO = 3.3 V, CO = 0 µF, and IO = IOmax) PARAMETER TEST CONDITIONS MIN IO Output Current Over VI range 0 VI Input Voltage Range Over IO Range 36 VO tol Set Point Voltage Tolerance TYP 48 V ±1.15 %VO Regline Line Regulation Over VI range ±5 Regload Load Regulation Over IO range ±5 ∆Votot Total Output Voltage Variation Includes set-point, line, load, –40°C >TA > 85°C ∆VADJ Output Adjust Range PO≤ 100 W η Efficiency IO = 50% IOmax VR VO Ripple (pk-pk) 20 MHz bandwidth Transient Response A 75 %VO –40°C >TA > 85°C ∆Vtr UNIT 30 ±1 (1) Regtemp Temperature Variation ttr MAX ±1.5 –20 mV mV ±3 %VO 10 %VO 92% 50 mVpp 150 µs VO over/undershoot 33 mV 41 A 0.1 A/µs slew rate, 50% to 75% IOmax ITRIP Overcurrent Threshold Shutdown, followed by auto-recovery OVP Output Overvoltage Protection Output shutdown and latch off 120 %VO OTP Over Temperature Protection Temperature Measurement at thermal sensor. Hysteresis = 10°C nominal. 105 °C fs Switching Frequency Over VI range 300 kHz UVLO Undervoltage Lockout VOFF VI decreasing, IO = 6 A 32.5 VHYS Hysteresis 1.5 V On/Off Input: Negative Enable VIH Input High Voltage VIL Input Low Voltage IIL Input Low Current Referenced to –VI 2.4 Open (2) –0.2 0.8 –0.3 V mA On/Off Input: Positive Enable Open (2) –0.2 0.8 Input High Voltage VIL Input Low Voltage IIL Input Low Current –0.5 mA IIsb Standby Input Current Output disabled (pin 2 status set to Off) 3 mA CI Internal Input Capacitance Between +VI and –VI 3 µF CO External Output Capacitance Between +VO and –VO Isolation Voltage Input-to-output and input-to-case Isolation Capacitance Input-to-output Isolation Resistance Input-to-output (1) (2) 4 4.5 VIH Referenced to –VI 0 30000 1500 µF Vdc 1200 10 If Sense(–) is not used, pin 5 must be connected to pin 4 for optimum output voltage accuracy. The Remote On/Off input has an internal pull-up and may be controlled with an open collector (drain) interface. An open circuit correlates to a logic high. Consult the application notes for interface considerations. Submit Documentation Feedback V pF MΩ PTQA430025, PTQA430033 www.ti.com SLTS261 – MAY 2006 PIN DESCRIPTIONS +VI: The positive input for the module with respect to –VI. When powering the module from a –48-V telecom central office supply, this input is connected to the primary system ground. –VI: The negative input supply for the module, and the 0 VDC reference for the Remote On/Off input. When powering the module from a +48-V supply, this input is connected to the 48-V return. Remote On/Off: This input controls the On/Off status of the output voltage. It is either driven low (–VI potential), or left open-circuit. For units identified with the NEN option, applying a logic low to this pin will enable the output. And for units identified with the PEN option, the output will be disabled. VO Adjust: Allows the output voltage to be trimmed by up or down between +10% and –20% of its nominal value. The adjustment method uses a single external resistor. Connecting the resistor between VO Adjust and –VO adjusts the output voltage lower, and placing it between VO Adjust and +VO adjusts the output higher. The calculations for the resistance value follows industry standard formulas. For further information consult the application note on output voltage adustment. +VO: The positive power output with respect to –VO, which is DC isolated from the input supply pins. If a negative output voltage is desired, +VO should be connected to the secondary circuit common and the output taken from –VO. –VO: The negative power output with respect to +VO, which is DC isolated from the input supply pins. This output is normally connected to the secondary circuit common when a positive output voltage is desired. Sense(+): Provides the converter with an output sense capability to regulate the set-point voltage directly at the load. When used with Sense(-), the regulation circuitry will compensate for voltage drop between the converter and the load. The pin may be left open circuit, but connecting it to +VO will improve load regulation. Sense(–): Provides the converter with an output sense capability when used in conjunction with Sense(+) input. For optimum output voltage accuracy this pin should always be connected to –VO. PTQA430xxxN (Top View) +VO 1 +VI Sense(+) 2 On/Off 3 −VI Adjust Sense(−) −VO Submit Documentation Feedback 8 7 6 5 4 5 PTQA430025, PTQA430033 www.ti.com SLTS261 – MAY 2006 TYPICAL CHARACTERISTICS PTQA430022, VO = 2.5 V All data listed in the graphs below have been developed from actual products tested at 25°C. This data is considered typical data for the DC-DC Converter. SOA curves represent operating conditions at which internal components are at or below manufacturer's maximum rated operating temperature. For Figure 4 Safe Operating Area, VI = 48 V. EFFICIENCY vs LOAD CURRENT OUTPUT RIPPLE vs LOAD CURRENT 95 VI = 75 V 75 VI = 60 V 70 VI = 48 V 60 55 50 VI= 75 V PD − Power Diddipation − W VO − Output Voltage Ripple − mVPP 80 65 VI= 60 V 45 85 Efficiency − % 12 50 VI = 36 V 90 η− POWER DISSIPATION vs LOAD CURRENT 40 35 30 25 20 VI= 48 V 15 VI= 36 V 8 VI = 75 V VI = 60 V 6 VI = 48 V 4 VI = 36 V 10 2 5 45 0 0 40 0 5 10 15 20 25 0 30 5 10 15 20 IO − Output Current − A IO − Output Current − A Figure 1. 25 30 Figure 2. TA − Ambient Temperature − oC 80 Natural Convection 70 LFM = 400 60 LFM = 200 50 LFM = 100 40 30 20 5 10 15 20 5 10 15 20 Figure 3. 90 0 0 IO − Output Current − A AMBIENT TEMPERATURE vs LOAD CURRENT 25 IO − Output Current − A Figure 4. 6 10 Submit Documentation Feedback 30 25 30 PTQA430025, PTQA430033 www.ti.com SLTS261 – MAY 2006 TYPICAL CHARACTERISTICS PTQA430033, VO = 3.3 V All data listed in the graphs below have been developed from actual products tested at 25°C. This data is considered typical data for the DC-DC Converter. SOA curves represent operating conditions at which internal components are at or below manufacturer's maximum rated operating temperature. For Figure 8 Safe Operating Area, VI = 48 V. EFFICIENCY vs LOAD CURRENT 40 VI = 36 V 14 90 VO − Output Voltage Ripple − mVPP 85 75 VI = 48 V VI = 60 V 70 VI = 75 V 60 55 50 VI= 75 V 12 30 25 20 VI= 48 V 15 VI= 36 V 10 10 8 VI= 60 V 6 4 45 5 2 40 0 0 VI= 36 V 0 5 10 15 20 25 30 IO − Output Current − A 0 10 15 20 IO − Output Current − A Figure 5. Figure 6. 5 25 30 VI= 48 V 0 5 10 15 20 25 30 IO − Output Current − A Figure 7. AMBIENT TEMPERATURE vs LOAD CURRENT 90 80 TA − Ambient Temperature − °C η− Efficiency − % 80 VI= 75 V VI= 60 V 35 65 POWER DISSIPATION vs LOAD CURRENT PD − Power Diddipation − W 95 OUTPUT RIPPLE vs LOAD CURRENT 70 LFM = 400 60 50 LFM = 200 40 LFM = 100 30 Natural Convection 20 0 5 10 15 20 25 30 IO − Output Current − A Figure 8. Submit Documentation Feedback 7 PTQA430025, PTQA430033 www.ti.com SLTS261 – MAY 2006 APPLICATION INFORMATION Operating Features and System Considerations for the PTQA4300xx Series of DC/DC Converters Overcurrent Protection To protect against load faults, these converters incorporate output overcurrent protection. Applying a load to the output that exceeds the converter's overcurrent threshold (see applicable specification) will cause the output voltage to momentarily fold back, and then shut down. Following shutdown the module will periodically attempt to automatically recover by initiating a soft-start power-up. This is often described as a hiccup mode of operation, whereby the module continues in the cycle of successive shutdown and power up until the load fault is removed. Once the fault is removed, the converter automatically recovers and returns to normal operation. Output Overvoltage Protection Each converter incorporates protection circuitry that continually senses for an output overvoltage (OV) condition. The OV threshold is set approximately 20% higher than the nominal output voltage. If the converter output voltage exceeds this threshold, the converter is immediately shut down and remains in a latched-off state. To resume normal operation the converter must be actively reset. This can only be done by momentarily removing the input power to the converter. For fail-safe operation and redundancy, the OV protection uses circuitry that is independent of the converter’s internal feedback loop. Overtemperature Protection Overtemperature protection is provided by an internal temperature sensor, which closely monitors the temperature of the converter’s printed circuit board (PCB). If the sensor exceeds a temperature of approximately 105°C, the converter will shut down. The converter will then automatically restart when the sensed temperature drops back to approximately 95°C. When operated outside its recommended thermal derating envelope (see data sheet SOA curves), the converter will typcially cycle on and off at intervals from a few seconds to one or two minutes. This is to ensure that the internal components are not permanently damaged from excessive thermal stress. Undervoltage Lockout The Undervoltage lockout (UVLO) is designed to prevent the operation of the converter until the input voltage is at the minimum input voltage. This prevents high start-up current during normal power-up of the converter, and minimizes the current drain from the input source during low input voltage conditions. The UVLO circuitry also overrides the operation of the Remote On/Off control. Primary-Secondary Isolation These converters incorporate electrical isolation between the input terminals (primary) and the output terminals (secondary). All converters are production tested to a withstand voltage of 1500 VDC. This specification complies with UL60950 and EN60950 and the requirements for operational isolation. This allows the converter to be configured for either a positive or negative input voltage source. The data sheet Pin Descriptions section provides guidance as to the correct reference that must be used for the external control signals. Input Current Limiting The converter is not internally fused. For safety and overall system protection, the maximum input current to the converter must be limited. Active or passive current limiting can be used. Passive current limiting can be a fast acting fuse. A 125-V fuse, rated no more than 10 A, is recommended. Active current limiting can be implemented with a current limited Hot-Swap controller. Thermal Considerations Airflow may be necessary to ensure that the module can supply the desired load current in environments with elevated ambient temperatures. The required airflow rate may be determined from the Safe Operating Area (SOA) thermal derating chart (see typical characteristics). 8 Submit Documentation Feedback PTQA430025, PTQA430033 www.ti.com SLTS261 – MAY 2006 Differential Remote Sense The remote sense pins allows the converter to precisely regulate the DC output voltage at a remote location. This might be a power plane on an inner layer of the host PCB. Connecting Sense(+) directly to +VO, and Sense(–) to –VO will improve output voltage accuracy. In the event that the sense pins are left open-circuit, an internal 10-Ω resistor between each sense pin and its corresponding output prevents an excessive rise in the output voltage. For practical reasons, the amount of IR voltage compensation should be limited to 0.5 V maximum. The remote sense feature is designed to compensate for limited amounts of IR voltage drop. It is not intended to compensate for the forward drop of a non-linear or frequency dependent components that may be placed in series with the converter output. Examples of such components include OR-ing diodes, filter inductors, ferrite beads, and fuses. Enclosing these components with the remote sense connections effectively places them inside the regulation control loop, which can affect the stability of the regulator. Using the Remote On/Off Function on the PTQA4300xx Series of DC/DC Converters For applications requiring output voltage On/Off control, the PTQA4300xx series of DC/DC converters incorporate a Remote On/Off control (pin 2). This feature can be used to switch the module off without removing the applied input source voltage. When placed in the Off state, the standby current drawn from the input source is typically reduced to 3 mA. Negative Output Enable (NEN) Models using the negative enable option, the Remote On/Off (pin 2) control must be driven to a logic low voltage for the converter to produce an output. This is accomplished by either permanently connecting pin 2 to –VI (pin 3), or driving it low with an external control signal. Table 1 shows the input requirements of pin 2 for those modules with the NEN option. Table 1. On/Off Control Requirements for Negative Enable PARAMETER MIN TYP MAX VIH Enable 2.4 V 20 V VIL Disable –0.2 V 0.8 V Vo/c Open-Circuit II Pin 2 at –VI 9V 15 V –0.75 mA Submit Documentation Feedback 9 PTQA430025, PTQA430033 www.ti.com SLTS261 – MAY 2006 Positive Output Enable (PEN) For those models with the positive enable (PEN) option, leaving pin 2 open circuit, (or driving it to an equivalent logic high voltage), will enable the converter output. This allows the module to produce an output voltage whenever a valid input source voltage is applied to +VI with respect to –VI. If a logic-low signal is then applied to pin 2 the converter output is disabled. Table 2 gives the input requirements of pin 2 for modules with the PEN option. Table 2. On/Off Control Requirements for Positive Enable PARAMETER MIN TYP MAX VIH Enable 4.5 V 20 V VIL Disable –0.2 V 0.8 V Vo/c Open-Circuit II Pin 2 at –VI 5V 7V –0.5 mA Notes: 1. The Remote On/Off control uses –VI (pin 3) as its ground reference. All voltages are with respect to –VI. 2. An open-collector device (preferably a discrete transistor) is recommended. A pull-up resistor is not required. If one is added the pull-up voltage should not exceed 20 V. Caution:Do not use a pull-resistor to +VI (pin 1). The remote On/Off control has a maximum input voltage of 20 V. Exceeding this voltage will overstress, and possibly damage, the converter. 3. The Remote On/Off pin may be controlled with devices that have a totem-pole output. This is provided the output high level voltage (VOH) meets the module's minimum VIH specified in Table 1. If a TTL gate is used, a pull-up resistor may be required to the logic supply voltage. 4. The converter incorporates an undervoltage lockout (UVLO). The UVLO keeps the converter off until the input voltage is close to the minimum specified operating voltage. This is regardless of the state of the Remote On/Off control. Consult the product specification for the UVLO input voltage thresholds. 10 Submit Documentation Feedback PTQA430025, PTQA430033 www.ti.com SLTS261 – MAY 2006 PTQA430xxxP Q1 BSS138 2 Remote On/Off 1 = Disable −VI 3 −VI Figure 9. Recommended Control or Remote On/Off Input Turn-On: With a valid input source voltage applied, the converter produces a regulated output voltage within 75 ms of the output being enabled. Figure 10 shows the output response of the PTQA430033P following the removal of the logic-low signal from the Remote On/Off (pin 2); see Figure 9. This corresponds to the drop in Q1 VGS in Figure 10. Although the rise-time of the output voltage is short (<10 ms), the indicated delay time will vary depending upon the input voltage and the module’s internal timing. The waveforms were measured with 48 VDC input voltage, and a 10-A resistive load. Turn-Off Time: When a valid input source is removed or if the Remote On/Off (pin 2) is used to disable the output, with no external output capacitance, the module powers down within 200 µs. Figure 11 shows that, during power down, there is a small undershoot, typically less than 300 mV (or less than a diode drop). If used to supply processor I/O voltages, the low undershoot ensures the parasitic diodes do not conduct current and potentially cause damage to external circuitry. VO (1 V/div) VO (1 V/div) II (1 A/div) < 300 mV Delay Time Q1 VGS (10 V/div) Voltage Undershoot t − Time − 100 µs/div t − Time − 5 ms/div Figure 10. Power Up Figure 11. Power Down Adjusting the Output Voltage of the 100-W Rated PTQA4300xx Series of Isolated DC/DC Converters The output voltage adjustment of the PTQA4300xx series of isolated DC/DC converters follows the standard adopted by popular 1/4-brick DC/DC converters. Adjustment is accomplished with a single external resistor that can adjust the output voltage from –20% to +10% of the nominal set-point voltage. The placement of the resistor determines the direction of adjustment, up or down, and the value of the magnitude of adjustment. Adjust Up: To increase the output voltage add a resistor, R1, between VO Adjust (pin 6) and Sense(+) (pin 7). Adjust Down: Add a resistor, (R2), between VO Adjust (pin 6) and Sense(–) (pin 5). Submit Documentation Feedback 11 PTQA430025, PTQA430033 www.ti.com SLTS261 – MAY 2006 Refer to Figure 12 for the placement of the required resistor, R1 or (R2). The values of R1 [adjust up], and (R2) [adjust down], can be calculated using the following formulas. 5.11 V O (100 ) D%) 511 R1 + * * 10.22 (kW) 1.225 D% D% (R2) + 5.11 100 * 10.22 (kW) D% (1) (2) Where: ∆% = Amount of adjustment in % VO = Original set-point voltage Notes: 1. Use only a single 1% resistor in either the R1 or (R2) location. Place the resistor as close to the converter as possible. 2. If the output voltage is increased, the maximum load current must be derated according to the following equation. V I O(rated) I O(max) + O VA (3) Where: VO = Original set-point voltage VA = Adjusted output voltage (measured between pins 8 and 4) In any instance, the load current must not exceed the converter's maximum rated output current of 30 A. 3. The overvoltage threshold is fixed, and is set approximately 20% above the nominal output voltage. Adjusting the output voltage higher reduces the voltage margin between the adjusted output voltage and the overvoltage (OV) protection threshold. This could make the module sensitive to OV fault detection, as a result of random noise and load transients. Sense (+) 7 Sense(+) 1 +V I +VO PTQA430xxxN 3 8 6 −VO 4 2 CO 330 µF Adjust −VI Remote On/Off R1 Adjust Up Sense(–) + +VI −VI +VO (R2) Adjust Down −VO 5 Sense (–) Figure 12. 12 Submit Documentation Feedback L O A D PTQA430025, PTQA430033 www.ti.com SLTS261 – MAY 2006 Table 3. Adjustment Resistor Values Adjusted Output Voltage (V) Trim-Up RADJ Trim-Down RADJ VO (nom) % Adjust (V) 3.3 V 2.5 V 3.3 V R1 (kΩ) 2.5 V R1 (kΩ) 3.3 V R2 (kΩ) 2.5 V R2 (kΩ) +10 3.630 2.750 90.9 53.6 - - +9 3.597 2.725 100 59.0 - - +8 3.564 2.700 113 66.5 - - +7 3.531 2.675 127 76.8 - - +6 3.498 2.650 147 88.7 - - +5 3.465 2.625 178 107 - - +4 3.432 2.600 221 133 - - +3 3.399 2.575 294 178 - - +2 3.366 2.550 432 267 - - +1 3.333 2.525 866 536 - - 0 3.300 2.500 Open Open - - –1 3.267 2.475 - - 499 499 –2 3.234 2.450 - - 243 243 –3 3.201 2.425 - - 158 158 –4 3.168 2.400 - - 118 118 –5 3.135 2.375 - - 90.9 90.9 –6 3.102 2.350 - - 75 75 –7 3.069 2.325 - - 63.4 63.4 –8 3.036 2.300 - - 53.6 53.6 –9 3.003 2.275 - - 46.4 46.4 –10 2.970 2.250 - - 41.2 41.2 –11 2.937 2.225 - - 36.5 36.5 –12 2.904 2.200 - - 32.4 32.4 –13 2.871 2.175 - - 28.7 28.7 –14 2.838 2.150 - - 26.1 26.1 –15 2.805 2.125 - - 23.7 23.7 –16 2.772 2.100 - - 21.5 21.5 –17 2.739 2.075 - - 19.6 19.6 –18 2.706 2.050 - - 18.2 18.2 –19 2.673 2.025 - - 16.5 16.5 –20 2.640 2.000 - - 15.4 15.4 Submit Documentation Feedback 13 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Low Power Wireless www.ti.com/lpw Mailing Address: Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2006, Texas Instruments Incorporated