1000 - 2500 Watts VS Series Special Features VS1-B2-H522-00 1100W total • Power factor correction • IEC 555-2 harmonic distortion compliance • CISPR 22, EN55022 Level B conducted / radiated EMI • EN61000 immunity standards • European CE Mark • Current share on all outputs • Remote sense on all outputs • Overload protection on all outputs • Voltage adjustment on all outputs • Margining on all outputs • AC-OK-signal (logics “1” or “0”) • Global DC OK (logics “1” or “0”) • DC-OK signal and status indicator LED-on all outputs • Global and individual module inhibits/enable • 3 year warranty • 2500 W with 3-phase input VS3-D2-C2-20 1200W total VS6-L2-00 1500W total Environmental Operating temperature: -10°C to 50°C (derate each output linearly to 60% at 70°C) 40°C max. for reverse air (option #1) Shock/Vibration: Mil-Hdbk 810E Humidity: 95% non-condensing VS8-L9-D9-20 2500W total (case limit) Storage temperature: -55°C to +85°C Temperature coefficient: 0.02% per °C Cooling: Internal DC fan 24V Safety VS4/9 2000 - 2500 W 1 UL UL60950-1 CSA CSA C22.2 No. 60950-1-03 VDE EN60950 CB Certificate and report CE Mark E133211 Technical Support: (888) 41-ASTEC or (407) 241-2752 Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 69-825-410 Rev C 12.01.04 AMERICAS EUROPE ASIA 5810 Van Allen Way Carlsbad, CA 92008 Telephone: 760-930-4600 Facsimile: 760-930-0698 Astec House, Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX, UK Telephone: 44 (1384) 842-211 Facsimile: 44 (1384) 843-355 Units 2111-2116, Level 21 Tower1, Metroplaza 223, Hing Fong Road Fwai Fong, New Territories Hong Kong Telephone: 852-2437-9662 Facsimile: 852-2402-4426 VS Series Electrical Specs Output Input Fuse rating 600 V / 25 A (internal)1Ø 250 V / 20 A (internal)3Ø Adjustment range ±10% minimum Margining ±4-6% nominal Input voltage 85-264 VAC 1Ø VS1, VS3 & VS4 Line/load reg 0.2% or 5 mV max. Ripple RMS: 0.1% or 10 mV P-P: 1.0% or 50 mV Bandwidth limited to 20 MHz Dynamic response 2% or 100 mV with 25% load step (any output) Recovery time To within 1% in <300 µsec Overvoltage protection 2-5 V 122% to 134% of output voltage; 12-48 V 110% to 120%; recycle AC Overload protection Main: 105% to 120% of rated current Auxiliaries:105% to 140% Short circuit protection Protected for continuous short circuit, recovery automatic (See operating curve) 180-264 VAC 3Ø VS6, VS8 & VS9 Frequency 47 to 440 Hz Inrush current 40 A peak max. Efficiency 75% - 82% Power factor 0.99 typical (0.9 on VS6, VS8 & VS9) Turn-on time AC / 1 sec; Inhibit / 100 ms max. EMI-filter CISPR 22, EN55022 Level B conducted/radiated Leakage current 2 mA max. at 240 VAC Reverse voltage protection Holdover storage 20 ms min. / 40 ms typical independent of VAC Thermal protection AC-OK warning time >5 ms (power fail) Each module thermally protected. Input module: auto recovery. Output modules; recycle AC. Loss of phase On VS6, VS8 & VS9, unit will continue to operate with loss of phase Remote sense Up to 0.5 V - total drop Single wire parallel Current share to 2% of total rated current Switching frequency 200 KHz (900-1500 W module, 400 KHz) DC OK -2% to -6% of nominal Output/Output isolation >1 Megohm Input Operating Curve 2200 1800 1600 1400 1200 1000 800 600 400 200 260 240 220 200 180 160 140 120 100 0 80 MAXIMUM OUTPUT POWER (W) 2000 100% of rated output current INPUT AC VOLTAGE (VAC) @ 50/60Hz Single Phase 2 www.astecpower.com 69-825-410 Rev C 12.01.04 Common Examples and Specifications Case size 1 = 5 inch, 2 slot, 3 = 8 inch, 4 slot, 4 = 11 inch, 6 slot, 6 = 5 inch, 2 slot, 8 = 8 inch, 4 slot, 9 = 11 inch, 6 slot, 1500 W max 1Ø 2000 W max 1Ø 2000 W max 1Ø 1500 W max 3Ø 2500 W max 3Ø 2500 W max 3Ø Option Codes 0 = no options 1 = rear air exhaust (40°C max.) 3 = set unit for global enable 5 = options 1 & 3 USE ONLY-FOR MODIFIED STANDARD, CONSULT-FACTORY (Same for Each Slot) Indicates CE compliance Parallel Code SLOT 1 SLOT 2 VS1 and VS6 available slots J1 J1 VS4 and VS9 available slots SLOT 1 SLOT 2 SLOT 4 SLOT 3 SLOT 5 N Parallel Codes SLOT 1 N SLOT 2 VS3 and VS8 available slots SLOT 3 Configuration Rules 1. Omit digits that do not apply. 2. a. Specify modules from lowest number of outputs to highest. b. If number of outputs are equal, specify from highest to lowest power increments. c. If power increments are equal, specify from highest to lowest current. 3. All model configurations created using this selection guide represent standard products with standard availability and lead times. 4. If slots are left empty, a blank panel will be automatically installed. SLOT 6 Output Voltage Code 0 = 2V 1 = 3.3 V 2= 5V 3 = 12 V 4 = 15 V 5 = 24 V 6 = 28 V 7 = 36 V 8 = special voltage (consult factory) 9 = 48 V SLOT 4 Output Module Code A = 300 W single 1 slot B = 600 W single 1 slot C = 900 W single 2 slots D = 1200 W single 2 slots E = 250 W dual 1 slot F = 250 W triple 1 slot G = 500 W dual 1 slot H = 500 W triple 1 slot K = 750 W single 1 slot L = 1500 W single 2 slot J1 0 = no parallel 1=1&2 Example (more on next page): 2=2&3 VS 1 - K 2 - G 3 3 - 0 0 - CE 5 inch case (2 slots available) 3=3&4 4=1&2 &3 No options Slot 1 1: 5V @ 150A Slot 2 2: 12V @ 21A 3: 12V @ 20A 5=2&3 &4 No paralleling 6=1&2+3&4 7=1&2&3&4 8=3&4+5&6 Output Current 9=1&2+3&4+5&6 Output Voltage Identification Module Identification Output Voltage Code 0 1 2 Output Voltage 2V 3.3 V 5V A (1 slot) 300 W Single 60 A 60 A 60 A B (1 slot) 600 W Single 120 A 120 A 120 A C (2 slots) 900 W Single 180 A 180 A 180 A D (2 slots) 1200 W Single 240 A 240 A 240 A E, F (1 slot) 250 W Multi Main Output 25 A 25 A 25 A G, H (1 slot) 500 W Multi Main Output 50 A 50 A 50 A K (1 slot) 750 W Single 150 A 150 A 150 A L (2 slots) 1500 W Single 300 A 300 A 300 A 3 4 5 12 V 15 V 24 V 25 A 20 A 12.5 A 50 A 40 A 25 A 75 A 60 A 37.5 A 100 A 80 A 50 A 10.5 A 8.3 A 5.3 A 21 A 16.6 A 10.5 A 62.5 A 50 A 31.2 A 125 A 100 A 62.4 A 6 7 9 28 V 36 V 48 V 10.7 A 8.3 A 6.3 A 21.4 A 16.6 A 12.5 A 32.1 A 24.9 A 18.75 A 42.8 A 33.2 A 25 A 4.5 A N/A N/A 9A N/A N/A 26.7 A 20.8 A 15.6 A 53.4 A 41.6 A 31.2 A Note: Increments of current not shown can be achieved by paralleling modules (add currents of each module selected). Auxiliary Output Table: Output(s) 2 and/or 3 of Module 3 Voltage Identification Module Identification Output Voltage Code Output Voltage E 250 W Dual Aux. Output F 250 W Triple Aux. Output G 500 W Dual Aux. Output H 500 W Triple Aux. Output 0 1 2 2V 3.3 V 5V 10 A 10 A 10 A 5A 5A 5A 20 A 20 A 20 A 10 A 10 A 10 A 3 4 5 6 12 V 15 V 24 V 28 V 10 A 10 A 5A 5A 5A 5A 2.5 A 2.5 A 20 A 20 A 10 A 10 A 10 A 10 A 5A 5A Technical Support: (888) 41-ASTEC or (407) 241-2752 Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 69-825-410 Rev C 12.01.04 AMERICAS EUROPE ASIA 5810 Van Allen Way Carlsbad, CA 92008 Telephone: 760-930-4600 Facsimile: 760-930-0698 Astec House, Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX, UK Telephone: 44 (1384) 842-211 Facsimile: 44 (1384) 843-355 Units 2111-2116, Level 21 Tower1, Metroplaza 223, Hing Fong Road Fwai Fong, New Territories Hong Kong Telephone: 852-2437-9662 Facsimile: 852-2402-4426 VS Series EXAMPLES Examples of Model Numbers - SINGLE OUTPUTS Total Power 600 W 750 W 900 W 1200 W 1200 W 1500 W 2000 W 2500 W Volts / Amps 5 V / 120 A 12 V / 62.5 A 5 V / 180 A 5 V / 240 A 2 V / 600 A 15 V / 100 A 5 V / 400 A 48 V / 52 A Size (H x W x L) 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 8 x 11 5 x 5 x 11 5 x 8 x 11 5 x 8 x 11 Model Number VS1-B2-00 VS1-K3-00 VS1-C2-00 VS1-D2-00 VS3-L0-L0-20 VS1-L4-00 VS3-D2-C2-20* VS8-L9-D9-20 ** * D2 module derated to 1100 W (2000 W max.) **D9 module derated to 1000 W (2500 W max ) Other Voltages Available Voltage ID Code 2V 3.3 V 5V 12 V 15 V 24 V 28 V 36 V Special 48 V 0 1 2 3 4 5 6 7 8 (consult factory) 9 Examples of Model Numbers - MULTIPLE OUTPUTS Total Power Output 1 Output 2 Output 3 Output 4 Output 5 Output 6 500 W 750 W 800 W 800 W 800 W 800 W 990 W 1000 W 1000 W 1100 W 1100 W 1100 W 1100 W 1100 W 1400 W 1400 W 1440 W 1600 W 1680 W 1700 W 1900 W 2000 W 2000 W 2500 W 5 / 50 5 / 50 5 / 60 5 / 60 5 / 60 5 / 60 5 / 150 5 / 50 5 / 50 5 / 120 5 / 120 5 / 170 5 / 120 5 / 120 5 / 180 5 / 180 5 / 240 5 / 170 5 / 240 5 / 240 5 / 180 5 / 300 5 / 240 5 / 300 12 / 10 12 / 10 12 / 21 12 / 21 15 / 16.6 15 / 16.6 2 / 120 12 / 10 12 / 10 12 / 21 12 / 21 12 / 10 15 / 16.6 15 / 16.6 12 / 21 12 / 21 2 / 120 12 / 20 2 / 240 12 / 21 12 / 21 12 / 21 12 / 21 3.3 / 120 12 / 10 12 / 10 12 / 10 12 / 10 15 / 10 15 / 10 15 / 8.3 5 / 10 24 / 5 5 / 10 24 / 5 15 / 5 5/5 15 / 16.6 15 / 16.6 15 / 10 5 / 10 24 / 5 24 / 5 15 / 10 24 / 5 15 / 10 15 / 10 24 / 5 12 / 10 12 / 10 12 / 20 12 / 10 12 / 10 15 / 10 15 / 10 12 / 20 12 / 10 5 / 10 5 / 10 24 / 5 5 / 10 12 / 21 5 / 20 12 / 20 12 / 20 12 / 10 12 / 20 12 / 21 5 / 50 5 / 10 5 / 60 12 / 10 Size Model Number 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 8 x 11 5 x 8 x 11 5 x 8 x 11 5 x 8 x 11 5 x 8 x 11 5 x 8 x 11 5 x 8 x 11 5 x 8 x 11 5 x 8 x 11 5 x 8 x 11 VS1-H233-00 VS1-H233-F442-00 VS1-A2-H332-00 VS1-A2-H335-00 VS1-A2-H442-00 VS1-A2-H445-00 VS1-K2-B0-00 VS1-H233-H445-00 VS1-H233-H425-00 VS1-B2-G33-00 VS1-B2-H332-00 VS1-B2-H233-10 VS1-B2-H442-00 VS1-B2-H445-00 VS3-C2-G33-00 VS3-C2-H332-00 VS3-D2-B0-00 VS3-B2-G23-G32-10 VS3-D2-D0-00 VS3-D2-G33-00 VS3-C2-G33-H245-00 VS3-L2-H332-00 VS3-D2-G33-H245-00 VS8-L2-B1-H334-00 Notes: Pin Assignments Electrical Characteristics PFC J1 CONTROL CONNECTOR Pin No. Function J1-1 AC OK Logic 1 J1-2 AC OK Logic 0 J1-3 Global DC OK/Conv Run Logic 1 J1-4 Global DC OK/Conv Run Logic 0 J1-5 Global DC OK/Conv Run/AC OK Return J1-6 Global Inhibit Logic 0*/ENA Logic '0' J1-7 Global Inhibit Logic 1*/ENA Logic '1' J1-8 Global Inhibit Return*ENA RTN J1-9 Global Isolated Inhibit J1-10 Global Isolated Inhibit Return Single Output J1 CONTROL CONNECTOR Pin No. Function J1-1 +Remote Sense J1-2 Remote Margin / V. Program J1-3 Remote Margin Hi J1-4 -Remote Sense / Margin Lo J1-5 DC OK / Conv Run Logic 1 J1-6 Isolated Inhibit J1-7 DC OK / Conv Run / ISO Inh. Return J1-8 Single Wire Parallel J1-9 Spare Pin J1-10 Spare Pin 1. DC OK minus 2 to 6% of nominal output voltage (tracking). 2. Inhibit & Enable are both TTL compatible. ISOLATED requires 2 mA source, typical. 3. DC OK/Converter Run denotes output voltage is present and converters are running (Or'ed signal configuration). 4. PFC LED: Red = Bulk DC bus voltage low; Green = Bulk DC OK. 5. Output LED: Red = Indicated output not operating within tolerance; Green = Indicated output operating within tolerance. 6. The 5 x 5 x 11 (VS1/6) case is power limited to 1500W max. See operating curve. 7. The 5 x 8 x 11 case and 5 x 11 x 11 case (VS3/4) are power limited to 2000W max. The VS8/9 cases are power limited to 2500W max. 8. Specifications subject to change without notice. 9. Warranty: 3 yrs * Changes to Enable with Option Code 3 Multiple Output J1 CONTROL CONNECTOR Pin No. Function J1-1 V1 +Remote Sense J1-2 V1 Remote Margin / V. Program J1-3 V1 Remote Margin Hi J1-4 V1 -Remote Sense / Margin Lo J1-5 V1 DC OK / Conv Run Logic 1 J1-6* V1 Isolated Inhibit J1-7 V1 DC OK / Conv Run / ISO Inh. Return J1-8 V1 Single Wire Parallel J1-9 V2 Single Wire Parallel J1-10 V3 Single Wire Parallel J2 CONTROL CONNECTOR Pin No. Function J2-1 V2 +Remote Sense J2-2 V2 Remote Margin / V. Program J2-3 V2 Remote Margin Hi J2-4 V2 -Remote Sense / Margin Lo J2-5 V2 DC OK /Logic 1 J2-6 V3 +Remote Sense J2-7 V3 Remote Margin / V. Program J2-8 V3 Remote Margin Hi J2-9 V3 -Remote Sense J2-10 V3 DC Good /Logic 1 * Inhibits off all the outputs within that module. www.astecpower.com 69-825-410 Rev C 12.01.04 4 Drawings VS1 & VS6 • 1000-1500 WATTS 5-inch Case Size (5” x 5” x 11”) Input Module 11.00 ± .05 (279.31 ± 1.27) .94 MAX 23.89) VS1 1.2 8-32 UNC-2B Threaded Insert, 4 Places Like Pattern Opposite Side Max penetration: 0.150 (3.81 ) 5.00 ± 0.05 STD AIR FLOW SLOT 1 SLOT 2 AC High Neutral Ground 5.00 Max (127.03) Side 4.000 ± .020 (101.60 ± .50) J1 2.04 ± .05 (51.82 ± 1.27) 3.49 ± .05 (88.65 ± 1.27) .500 ± .050 (12.70 ± 1.27) 6.750 ± .020 (171.45 ± .50) AC Main Input .750 ± .050 (19.05 ± 1.27) .27 ± .05 (6.86 ± 1.27) Bottom 8-32 UNC-2B Threaded Insert, 4 Places Max penetration: 0.150 (3.81) VS6 Input Module 5.00 ± 0.05 AC Ground N SLOT 1 6.750 ± .020 (171.45 ± .50) SLOT 2 AC Phase A AC Phase B AC Phase C 5.00 Max (127.03) Back J1 2.04 ± .05 (51.82 ± 1.27) .750 ± .050 (19.05 ± 1.27) 4.000 ± .020 (101.60 ± .50) 3.49 ± .05 (88.65 ± 1.27) .500 ± .050 (12.70 ± 1.27) NOTES (ALL MODELS) 1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). For VS1, VS3 & VS4 additional GND CONN added for VS6, VS8 & VS9. Max torque: 10 in-lbs (1.1 N-m). 2. Control connectors: (J1 and J2) 10 position Molex 90130-3210 housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes mating connector and 10 pins, Astec part #70-841-004. 3. Output terminals (A-300 W) (B-600 W) & (K-750 W) single modules: two (2) 10-32 UNF HEX HD BOLTS. Max. torque: 25 in-lbs (2.78 N-m). 4. Output terminals (E/F-250 W) & (G/H-500 W) dual/triple modules: Primary: two (2) 10-32 UNF HEX HD BOLTS. Max. torque: 25 in-lbs (2.78 N-m). Secondary: barrier strip two (2) 6-32 UNC screws (0.375” centers) per output. Max torque: 10 in-lbs (1.1 N-m). 5. Output terminals (C-900 W) (D-1200 W) & (L-1500 W) single modules: four 5/16-18 x 5/8" hex head cap screws. Max. torque: 120 in-lbs (13.35 N-m). Captive lock washer provided. 6. Chassis material: aluminum with chemical film coating. 7. Adjustment access: voltage, power fail, and overcurrent from front panel. 8. Bar code: code 39 extended. 9. Mounting for 5-inch & 8-inch case: four(4) 8-32 clinch nuts on three (3) surfaces. Mounting for 11-inch case: four (4) 8-32 clinch nuts on two (2) side surfaces & six (6) 8-32 clinch nuts on bottom surface. Max. penetration 0.150 inch (3.81). Max. torque: 15 in-lbs (1.67 N-m). 10. Additional support is recommended when unit is mounted in a suspended configuration. Mounting clinch nuts are not designed to support the weight of the unit. 11. Fans: 5-inch case, (1) 4.5" dia, 112 CFM (no load), 49 dBA. 8-inch case, (1) 4.5" dia, 112 CFM (no load), 49 dBA; (2) 2.25” dia, 23 CFM (no load), 38 dBA. 11-inch case, (2) 4.5" dia, 112 CFM (no load), 49dBA 12. All dimensions are in inches (mm). 13. Specifications subject to change without notice. 5 Technical Support: (888) 41-ASTEC or (407) 241-2752 Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 69-825-410 Rev C 12.01.04 EUROPE ASIA 5810 Van Allen Way Carlsbad, CA 92008 Telephone: 760-930-4600 Facsimile: 760-930-0698 Astec House, Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX, UK Telephone: 44 (1384) 842-211 Facsimile: 44 (1384) 843-355 Units 2111-2116, Level 21 Tower1, Metroplaza 223, Hing Fong Road Fwai Fong, New Territories Hong Kong Telephone: 852-2437-9662 Facsimile: 852-2402-4426 DRAWINGS • VS3 & VS8 • 1000-2500 WATTS VS Series 8-inch Case Size (5” x 8” x 11”) (18 lbs. / 8.2 kg. maximum) AMERICAS VS3 Input Module 11.00 ± .05 (279.31 ± 1.27) .94 MAX 23.89) 7.90 ± 0.05 (200.66 ± 1.27) 1.2 8-32 UNC-2B Threaded Insert, 4 Plac Like Pattern Opposite S Max penetration: 0.150 STD AIR FLOW SLOT 1 SLOT 2 SLOT 3 SLOT 4 AC High Neutral Ground 5.00 MAX (127.03) Side 4.000 ± .020 (101.60 ± .50) J1 2.04 ± .05 (51.82 ± 1.27) 3.49 ± .10 (88.65 ± 2.54) 4.94 ± .10 (125.48 ± 2.54) .500 ± .050 (12.70 ± 1.27) 6.39 ± .10 (162.31 ± 2.54) 6.750 ± .020 (171.45 ± .50) .750 ± .050 (19.05 ± 1.27) .27 ± .05 (6.86 ± 1.27) AC Main Input Bottom Back VS8 7.90 ± 0.05 (200.66 ± 1.27) 1.2 6.750 ± .020 (171.450 ± .50) Input Module SLOT 1 N SLOT 2 AC Ground SLOT 3 .750 ± .050 (19.05 ± 1.27) AC Phase A AC Phase B AC Phase C SLOT 4 8-32 UNC-2B Threaded Insert, 4 Places Max penetration: 0.150 (3.81) 5.00 MAX (127.03) J1 2.04 ± .05 (51.82 ± 1.27) 1.067 ± .050 (27.099 ± 1.270) 5.750 ± .020 (146.050 ± .508) 3.49 ± .10 (88.65 ± 2.54) 4.94 ± .10 (125.48 ± 2.54) 6.39 ± .10 (162.31 ± 2.54) 6 www.astecpower.com 69-825-410 Rev C 12.01.04 Drawings VS4 & VS9 • 2000-2500 WATTS 1.2 8-32 UNC-2B THREADED INSERT, 6 PL 11-inch Case Size (5” x 11” x 11”) VS4 10.80 ±.20 274.32 ±5.04 (PFC) ~ AC HIGH NEUTRAL GROUND S INTERNAL FUSE 25 AMPS/600V ~ N .52 13.1 P/F 6 1 S S S S S L L L L L L O O O O O O T T T T T T 6 5 4 3 2 1 6.750 171.450 5.00 127.0 ±.02 ±.50 MAX .750 19.050 ±.05 ±1.270 J1 .33 8.3 2.04 ±.10 51.81 ±2.54 3.49 ±.10 88.64 ±2.54 DETAIL A 1.067 ±.050 27.099 ±1.270 4.94 ±.10 125.47 ±2.54 5.750 ±.020 146.050 ±.508 6.39 ±.10 162.31 ±2.54 8.750 ±.020 222.25 ±.508 7.84 ±.10 199.14 ±2.54 9.29 ±.10 235.97 ±2.54 .94 MAX 23.89 VS9 11.00 ±.05 279.31 ±1.27 10.80 ±.20 274.32 ±5.04 1.2 8-32 UNC-2B THREADED INSERT, 4 PL LIKE PATTERN OPPOSITE SIDE (PFC) ACAC Phase HIGHA ACNEUTRAL Phase B AC GROUND Phase C 4.00 ±.02 101.60 ±.50 MAX ~ N INTERNAL FUSE 25 AMPS/600V STD AIR FLOW FRONT AIR EXHAUST ~ .52 13.1 OPTIONAL REAR AIR EXHAUST P/F 6 1 S S S S S L L L L L S L O O O O O O T T T T T T 6 5 4 3 2 1 J1 .33 8.3 2.04 ±.10 51.81 ±2.54 3.49 ±.10 88.64 ±2.54 .50 ±.05 12.70 ±1.27 .75 ±.05 19.05 ±1.27 6.75+.02 171.45 +.50 .27 ±.05 6.86 ±1.27 7 DETAIL A 4.94 ±.10 125.47 ±2.54 6.39 ±.10 162.31 ±2.54 7.84 ±.10 199.14 ±2.54 9.29 ±.10 235.97 ±2.54 Technical Support: (888) 41-ASTEC or (407) 241-2752 Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 69-825-410 Rev C 12.01.04 5.00 127.0 MAX www.astec.com BLANK (1 SLOT) 1.442 REF 2.31 ?.050 58.59 ?1.27 1.38 ?.050 34.94 ?1.27 .52 13.1 1.03 ?.050 26.21 ?1.27 J1 MODULE CODES C = 900W D = 1200W L = 1500W 900W/1200W/1500W SINGLE OUTPUT (2 SLOTS) 2.874 REF 1.79 45.5 - + 1.00 25.40 ?.050 ?1.27 3.70 94.16 .66 16.80 ?.050 ?1.27 ?.050 ?1.27 ?.050 ?1.27 .33 8.3 .52 13.1 1.442 REF J1 + MODULE CODES A = 300W B = 600W K = 750W 3.70 94.16 ?.050 ?1.27 MODULE CODES E = 250W DUAL F = 250W TRIPLE G = 500W DUAL H = 500W TRIPLE 1.442 REF J2 - .66 16.80 ?.050 ?1.27 300W/600W/750W SINGLE OUTPUT (1 SLOT) + + - J1 + .60 15.24 250W/500W DUAL/TRIPLE OUTPUT (1 SLOT) .52 13.1 ?.050 ?1.27 .33 8.3 2.77 70.3 .60 15.24 DETAIL A .52 13.1 PH PH PH AMERICAS EUROPE ASIA 5810 Van Allen Way Carlsbad, CA 92008 Telephone: 760-930-4600 Facsimile: 760-930-0698 Astec House, Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX, UK Telephone: 44 (1384) 842-211 Facsimile: 44 (1384) 843-355 Units 2111-2116, Level 21 Tower1, Metroplaza 223, Hing Fong Road Fwai Fong, New Territories Hong Kong Telephone: 852-2437-9662 Facsimile: 852-2402-4426 Module Front Panels 69-825-410 Rev C 12.01.04 153