w WM8980 Stereo CODEC with Speaker Driver and Video Buffer DESCRIPTION FEATURES The WM8980 is a low power, high quality stereo CODEC with integrated video buffer designed for portable applications such as multimedia phone, digital still camera or digital camcorder. Stereo CODEC: DAC SNR 98dB, THD -84dB (‘A’ weighted @ 48kHz) ADC SNR 95dB, THD -80dB (‘A’ weighted @ 48kHz) On-chip Headphone Driver with ‘capless’ option - 40mW per channel into 16 / 3.3V SPKVDD 1W output power into 8 BTL speaker / 5V SPKVDD - Capable of driving piezo speakers - Stereo speaker drive configuration Mic Preamps: Stereo Differential or mono microphone Interfaces - Programmable preamp gain - Psuedo differential inputs with common mode rejection - Programmable ALC / Noise Gate in ADC path Low-noise bias supplied for electret microphones Other Features: Integrated video buffer with LPF filter and clamp. Enhanced 3-D function for improved stereo separation Digital playback limiter 5-band Equaliser (record or playback) Programmable ADC High Pass Filter (wind noise reduction) Programmable ADC Notch Filter Aux inputs for stereo analog input signals or ‘beep’ On-chip PLL supporting 12, 13, 19.2MHz and other clocks Support for 8, 11.025, 12, 16, 22.05, 24, 32, 44.1 and 48kHz sample rates Low power, low voltage - 2.5V to 3.6V (digital: 1.71V to 3.6V) 6x6mm 40-lead QFN package The device integrates preamps for stereo differential mics, and includes drivers for speakers, headphone and differential or stereo line output. External component requirements are reduced as no separate microphone or headphone amplifiers are required. An integrated video buffer is provided which has programmable rd gain from 0-6dB (6-12dB unloaded), sync-tip clamp and a 3 order input low pass filter for signal re-construction. Advanced on-chip digital signal processing includes a 5-band equaliser, a mixed signal Automatic Level Control for the microphone or line input through the ADC as well as a purely digital limiter function for record or playback. Additional digital filtering options are available in the ADC path, to cater for application filtering such as ‘wind noise reduction’. The WM8980 digital audio interface can operate as a master or a slave. An internal PLL can generate all required audio clocks for the CODEC from common reference clock frequencies, such as 12MHz and 13MHz. The WM8980 operates at analogue supply voltages from 2.5V to 3.3V, although the digital core can operate at voltages down to 1.71V to save power. The speaker outputs and OUT3/4 line outputs can run from a 5V supply if increased output power is required. Individual sections of the chip can also be powered down under software control. BLOCK DIAGRAM APPLICATIONS WOLFSON MICROELECTRONICS plc To receive regular email updates, sign up at http://www.wolfsonmicro.com/enews Stereo Camcorder or DSC Multimedia Phone Pre-Production, May 2012, Rev 3.8 Copyright 2012 Wolfson Microelectronics plc. WM8980 Pre-Production TABLE OF CONTENTS DESCRIPTION ....................................................................................................... 1 BLOCK DIAGRAM ................................................................................................ 1 FEATURES ............................................................................................................ 1 APPLICATIONS..................................................................................................... 1 TABLE OF CONTENTS ......................................................................................... 2 PIN CONFIGURATION .......................................................................................... 4 ORDERING INFORMATION .................................................................................. 4 PIN DESCRIPTION ................................................................................................ 5 ABSOLUTE MAXIMUM RATINGS ........................................................................ 6 RECOMMENDED OPERATING CONDITIONS ..................................................... 6 ELECTRICAL CHARACTERISTICS ..................................................................... 7 TERMINOLOGY ............................................................................................................ 10 SPEAKER OUTPUT THD VERSUS POWER ...................................................... 11 POWER CONSUMPTION .................................................................................... 12 ESTIMATING SUPPLY CURRENT ............................................................................... 12 AUDIO PATHS OVERVIEW ................................................................................ 14 SIGNAL TIMING REQUIREMENTS .................................................................... 15 SYSTEM CLOCK TIMING ............................................................................................. 15 AUDIO INTERFACE TIMING – MASTER MODE .......................................................... 15 AUDIO INTERFACE TIMING – SLAVE MODE ............................................................. 16 CONTROL INTERFACE TIMING – 3-WIRE MODE ...................................................... 17 CONTROL INTERFACE TIMING – 2-WIRE MODE ...................................................... 18 INTERNAL POWER ON RESET CIRCUIT .......................................................... 19 DEVICE DESCRIPTION ...................................................................................... 21 INTRODUCTION ........................................................................................................... 21 INPUT SIGNAL PATH ................................................................................................... 23 ANALOGUE TO DIGITAL CONVERTER (ADC) ........................................................... 31 INPUT LIMITER / AUTOMATIC LEVEL CONTROL (ALC)............................................ 35 OUTPUT SIGNAL PATH ............................................................................................... 47 3D STEREO ENHANCEMENT ...................................................................................... 54 ANALOGUE OUTPUTS ................................................................................................. 54 VIDEO BUFFER ............................................................................................................ 70 DIGITAL AUDIO INTERFACES ..................................................................................... 74 AUDIO SAMPLE RATES ............................................................................................... 79 MASTER CLOCK AND PHASE LOCKED LOOP (PLL) ................................................ 79 GENERAL PURPOSE INPUT/OUTPUT........................................................................ 83 OUTPUT SWITCHING (JACK DETECT)....................................................................... 84 CONTROL INTERFACE ................................................................................................ 86 RESETTING THE CHIP ................................................................................................ 87 POWER SUPPLIES....................................................................................................... 87 RECOMMENDED POWER UP/DOWN SEQUENCE .................................................... 87 POWER MANAGEMENT .............................................................................................. 92 REGISTER MAP .................................................................................................. 93 REGISTER BITS BY ADDRESS ................................................................................... 95 DIGITAL FILTER CHARACTERISTICS ............................................................ 113 TERMINOLOGY .......................................................................................................... 113 DAC FILTER RESPONSES ........................................................................................ 114 ADC FILTER RESPONSES ........................................................................................ 114 HIGHPASS FILTER ..................................................................................................... 115 w PP, Rev 3.8, May 2012 2 Pre-Production WM8980 5-BAND EQUALISER .................................................................................................. 116 APPLICATION INFORMATION ......................................................................... 120 RECOMMENDED EXTERNAL COMPONENTS ......................................................... 120 PACKAGE DIAGRAM ....................................................................................... 121 IMPORTANT NOTICE ....................................................................................... 122 ADDRESS: .................................................................................................................. 122 REVISION HISTORY ......................................................................................... 123 w PP, Rev 3.8, May 2012 3 WM8980 Pre-Production PIN CONFIGURATION ORDERING INFORMATION ORDER CODE TEMPERATURE RANGE PACKAGE MOISTURE SENSITIVITY LEVEL PEAK SOLDERING TEMPERATURE WM8980CGEFL/V -25C to +85C 40-lead QFN (6 x 6 mm) (Pb-free) MSL3 260 C WM8980CGEFL/RV -25C to +85C 40-lead QFN (6 x 6 mm) (Pb-free, tape and reel) MSL3 260 C o o Note: Reel quantity = 3,500 w PP, Rev 3.8, May 2012 4 WM8980 Pre-Production PIN DESCRIPTION PIN NAME TYPE 1 L2/GPIO2 Analogue input 2 RIP Analogue input Right Mic Pre-amp positive input 3 RIN Analogue input Right Mic Pre-amp negative input 4 R2/GPIO3 Analogue input 5 VBGND Supply Video buffer ground pin 6 VBIN Analogue input Video buffer signal input 7 VBREF Analogue output Video buffer reference resistor pin 8 VBOUT Analogue output Video buffer output 9 VBVDD Supply 10 NC Not internally connected 11 LRC Digital Input / Output 12 BCLK Digital Input / Output 13 ADCDAT Digital Output 14 DACDAT Digital Input 15 MCLK Digital Input 16 DGND Supply Digital ground 17 DCVDD Supply Digital core logic supply Digital buffer (I/O) supply 18 DBVDD Supply 19 CSB/GPIO1 Digital Input / Output 20 SCLK Digital Input 21 SDIN Digital Input / Output DESCRIPTION Left channel line input/secondary mic pre-amp positive input/GPIO2 pin Right channel line input/secondary mic pre-amp positive input/GPIO3 pin Video buffer analogue supply DAC and ADC Sample Rate Clock Digital Audio Bit Clock ADC Digital Audio Data Output DAC Digital Audio Data Input Master Clock Input 3-Wire Control Interface Chip Select / GPIO1 pin 3-Wire Control Interface Clock Input / 2-Wire Control Interface Clock Input 3-Wire Control Interface Data Input / 2-Wire Control Interface Data Input 22 MODE Digital Input 23 GPIO4 Digital input/output Control Interface Selection 24 NC Not internally connected 25 AUXL Analogue input Left Auxilary input 26 AUXR Analogue input Right Auxilary input 27 OUT4 Analogue Output Buffered midrail Headphone pseudo-ground, or Right line output or MONO mix output 28 OUT3 Analogue Output Buffered midrail Headphone pseudo-ground, or Left line output 29 ROUT2 Analogue Output 30 SPKGND Supply 31 LOUT2 Analogue Output 32 SPKVDD Supply 33 VMID Reference 34 AGND Supply 35 ROUT1 Analogue Output Headphone or Line Output Right 36 LOUT1 Analogue Output Headphone or Line Output Left 37 AVDD Supply 38 MICBIAS Analogue Output 39 LIP Analogue input Left Mic Pre-amp positive input 40 LIN Analogue input Left Mic Pre-amp negative input General purpose input/output 4 Second right output, or BTL speaker driver negative output Speaker ground (feeds speaker amp and OUT3/OUT4) Second left output, or BTL speaker driver positive output Speaker supply (feeds speaker amp only) Decoupling for ADC and DAC reference voltage Analogue ground (feeds ADC and DAC) Analogue supply (feeds ADC and DAC) Microphone Bias Note: It is recommended that the QFN ground paddle should be connected to analogue ground on the application PCB. w PP, Rev 3.8, May 2012 5 WM8980 Pre-Production ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are stress ratings only. Permanent damage to the device may be caused by continuously operating at or beyond these limits. Device functional operating limits and guaranteed performance specifications are given under Electrical Characteristics at the test conditions specified. ESD Sensitive Device. This device is manufactured on a CMOS process. It is therefore generically susceptible to damage from excessive static voltages. Proper ESD precautions must be taken during handling and storage of this device. Wolfson tests its package types according to IPC/JEDEC J-STD-020B for Moisture Sensitivity to determine acceptable storage conditions prior to surface mount assembly. These levels are: MSL1 = unlimited floor life at <30C / 85% Relative Humidity. Not normally stored in moisture barrier bag. MSL2 = out of bag storage for 1 year at <30C / 60% Relative Humidity. Supplied in moisture barrier bag. MSL3 = out of bag storage for 168 hours at <30C / 60% Relative Humidity. Supplied in moisture barrier bag. The Moisture Sensitivity Level for each package type is specified in Ordering Information. CONDITION DBVDD, DCVDD, AVDD, VBVDD supply voltages SPKVDD supply voltage MIN MAX -0.3V +4.5V -0.3V +7V Voltage range digital inputs DGND -0.3V DVDD +0.3V Voltage range analogue inputs AGND -0.3V AVDD +0.3V Operating temperature range, TA -25C +85C Storage temperature after soldering -65C +150C Notes 1. Analogue and digital grounds must always be within 0.3V of each other. 2. All digital and analogue supplies are completely independent from each other. RECOMMENDED OPERATING CONDITIONS PARAMETER SYMBOL Digital supply range (Core) DCVDD 1.71 1 3.6 V Digital supply range (Buffer) DBVDD 1.71 3.6 V V Analogue core supply range Video buffer supply range Analogue output supply range Ground TEST CONDITIONS MIN TYP MAX UNIT AVDD 2.5 3.6 VBVDD 2.5 3.6 V SPKVDD 2.5 5.5 V DGND,AGND, SPKGND,VBGND 0 V Notes 1. When using the PLL, DCVDD must not be less than 1.9V. 2. DBVDD must be greater than or equal to DCVDD. 3. Analogue supplies have to be to digital supplies. 4. In non-boosted mode, SPKVDD should = AVDD, if boosted SPKVDD should be 1.5x AVDD. w PP, Rev 3.8, May 2012 6 WM8980 Pre-Production ELECTRICAL CHARACTERISTICS Test Conditions o DCVDD=1.8V, AVDD=DBVDD=SPKVDD=VBVDD = 3.3V, TA = +25 C, 1kHz signal, fs = 48kHz, 24-bit audio data unless otherwise stated. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT Microphone Preamp Inputs (LIP, LIN, RIP, RIN, L2, R2) Full-scale Input Signal Level – note this changes in proportion to AVDD (Note 1) VINFS Mic PGA equivalent input noise PGABOOST = 0dB 1.0 Vrms INPPGAVOL = 0dB 0 dBV At 35.25dB gain 0 to 20kHz 150 uV RMICIN Gain set to 35.25dB 1.6 k RMICIN Gain set to 0dB 47 k RMICIN Gain set to -12dB 75 k RMICIP L/RIP2INPPGA = 1 94 k 10 pF Maximum Programmable Gain 35.25 dB Minimum Programmable Gain -12 dB 0.75 dB 120 dB Boost disabled 0 dB Boost enabled 20 dB Maximum Gain from AUXL/R or L/R2 input to boost/mixer +6 dB Minimum Gain from AUXL/R or L/R2 input to boost/mixer -12 dB 3 dB AVDD/3.3 Vrms 0 dBV Input resistance CMICIN MIC Programmable Gain Amplifier (PGA) Programmable Gain Step Size Guaranteed monotonic Mute Attenuation Selectable Input Gain Boost (0/+20dB) Gain Boost on PGA input Gain step size to boost/mixer Guaranteed monotonic Auxiliary Analogue Inputs (AUXL, AUXR) Full-scale Input Signal Level (0dB) – note this changes in proportion to AVDD Input Resistance VINFS RAUXINLMIN Left Input boost and mixer enabled, at max gain 4.3 k RAUXINLTYP Left Input boost and mixer enabled, at 0dB gain 8.6 k RAUXINLMAX Left Input boost and mixer enabled, at min gain 39.1 k RAUXINRMIN Right Input boost, mixer and beep enabled, at max gain 3 k RAUXINRTYP Right Input boost, mixer and beep enabled, at 0dB gain 6 k RAUXINRMAX Right Input boost, mixer and beep enabled, at min gain 29 k 10 pF (Note 2) Input Capacitance w CMICIN PP, Rev 3.8, May 2012 7 WM8980 Pre-Production Test Conditions o DCVDD=1.8V, AVDD=DBVDD=SPKVDD=VBVDD = 3.3V, TA = +25 C, 1kHz signal, fs = 48kHz, 24-bit audio data unless otherwise stated. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT dB Automatic Level Control (ALC) Target Record Level -22.5 -1.5 Programmable gain -12 35.25 Gain Hold Time (Note 3,5) Gain Ramp-Up (Decay) Time (Note 4,5) Gain Ramp-Down (Attack) Time (Note 4,5) tHOLD tDCY tATK MCLK = 12.288MHz (Note 3) 0, 2.67, 5.33, 10.67, … , 43691 ms (time doubles with each step) 3.3, 6.6, 13.1, … , 3360 ms ALCMODE=0 (ALC), MCLK=12.288MHz (Note 3) (time doubles with each step) ALCMODE=1 (limiter), MCLK=12.288MHz (Note 3) (time doubles with each step) ALCMODE=0 (ALC), MCLK=12.288MHz (Note 3) (time doubles with each step) ALCMODE=1 (limiter), MCLK=12.288MHz (Note 3) (time doubles with each step) 0.73, 1.45, 2.91, … , 744 0.83, 1.66, 3.33, … , 852 ms 0.18, 0.36, 0.73, … , 186 Mute Attenuation 120 dB Analogue to Digital Converter (ADC) Signal to Noise Ratio (Note 6) SNR A-weighted, 0dB gain Total Harmonic Distortion THD -3dBFS input -84 1kHz input signal 110 dB AVDD/3.3 Vrms 85 95 dB -74 dB (Note 7) Channel Separation (Note 9) Digital to Analogue Converter (DAC) to Line-Out (LOUT1, ROUT1 with 10k / 50pF load) Full-scale output PGA gains set to 0dB, OUT34BOOST=0 PGA gains set to 0dB, 1.5x OUT34BOOST=1 (AVDD/3.3) Signal to Noise Ratio (Note 6) SNR A-weighted Total Harmonic Distortion THD RL = 10k (Note 7) 90 98 -84 dB -76 dB full-scale signal Channel Separation (Note 8) 1kHz signal 110 dB Maximum PGA gain into mixer +6 dB Minimum PGA gain into mixer -15 dB 3 dB Maximum Programmable Gain +6 dB Minimum Programmable Gain -57 dB Output Mixers (LMX1, RMX1) PGA gain step into mixer Guaranteed monotonic Analogue Outputs (LOUT1, ROUT1, LOUT2, ROUT2) Programmable Gain step size Guaranteed monotonic 1 dB Mute attenuation 1kHz, full scale signal 85 dB Headphone Output (LOUT1, ROUT1 with 32 load) 0dB full scale output voltage AVDD/3.3 Vrms Signal to Noise Ratio SNR A-weighted 102 dB Total Harmonic Distortion THD RL = 16, Po=20mW 0.003 % AVDD=3.3V -75 dB RL = 32 , Po=20mW 0.008 % AVDD=3.3V - 82 dB w PP, Rev 3.8, May 2012 8 WM8980 Pre-Production Test Conditions o DCVDD=1.8V, AVDD=DBVDD=SPKVDD=VBVDD = 3.3V, TA = +25 C, 1kHz signal, fs = 48kHz, 24-bit audio data unless otherwise stated. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT Speaker Output (LOUT2, ROUT2 with 8 bridge tied load, INVROUT2=1) Full scale output voltage, 0dB gain. (Note 9) Output Power Total Harmonic Distortion PO THD SPKBOOST=0 SPKVDD/3.3 SPKBOOST=1 (SPKVDD/3.3)*1.5 Output power is very closely correlated with THD; see below PO =200mW, RL = 8, SPKVDD=3.3V 0.04 % -68 dB PO =320mW, RL = 8, SPKVDD=3.3V PO =500mW, RL = 8, SPKVDD=5V Signal to Noise Ratio SNR Vrms 1.0 % -40 dB 0.02 % -74 dB PO =860mW, RL = 8, SPKVDD=5V 1.0 % -40 dB SPKVDD=3.3V, 90 dB 90 dB RL = 8 SPKVDD=5V, RL = 8 Power Supply Rejection Ratio PSRR (50Hz-22kHz) RL = 8 BTL 80 dB RL = 8 BTL SPKVDD=5V (boost) 69 dB OUT3BOOST=0/ SPKVDD/3.3 Vrms (SPKVDD/3.3)*1.5 Vrms OUT3/OUT4 outputs (with 10k / 50pF load) Full-scale output voltage, 0dB gain (Note 9) OUT4BOOST=0 OUT3BOOST=1 OUT4BOOST=1 Signal to Noise Ratio (Note 6) SNR A-weighted 98 dB Total Harmonic Distortion THD RL = 10 k -84 dB 1kHz signal 100 dB RL = 10k 52 dB RL = 10k SPKVDD=5V (boost) 56 dB MBVSEL=0 0.9*AVDD V MBVSEL=1 0.65*AVDD (Note7) full-scale signal Channel Separation (Note 8) Power Supply Rejection Ratio PSRR (50Hz-22kHz) Microphone Bias Bias Voltage VMICBIAS Bias Current Source IMICBIAS Output Noise Voltage Vn V 3 1K to 20kHz 15 mA nV/Hz Video Buffer rd Low pass filter order 3 order LPF -3dB cutoff 10 LPF gain flat to within 0.1dB 5.3 MHz 1.25 Vp-p Maximum output voltage swing Vom f=100kHz, THD=1% MHz Programmable Voltage Gain Av Differential gain DG Vin=1Vp-p 0.3 % Differential phase DP Vin=1Vp-p 0.7 Deg +60 dB Signal to Noise Ratio w VSNR 0 6 dB PP, Rev 3.8, May 2012 9 WM8980 Pre-Production Test Conditions o DCVDD=1.8V, AVDD=DBVDD=SPKVDD=VBVDD = 3.3V, TA = +25 C, 1kHz signal, fs = 48kHz, 24-bit audio data unless otherwise stated. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT 0.3DBVDD V Digital Input / Output Input HIGH Level VIH Input LOW Level VIL Output HIGH Level VOH IOL=1mA Output LOW Level VOL IOH-1mA 0.7DBVDD V 0.9DBVDD V 0.1xDBVDD V Input capacitance 10 pF Input leakage 50 pA TERMINOLOGY 1. Input level to RIP and LIP is limited to a maximum of -3dB or THD+N performance will be reduced. 2. Note when BEEP path is not enabled then AUXL and AUXR have the same input impedances. 3. Hold Time is the length of time between a signal detected being too quiet and beginning to ramp up the gain. It does not apply to ramping down the gain when the signal is too loud, which happens without a delay. 4. Ramp-up and Ramp-Down times are defined as the time it takes for the PGA to sweep across 90% of its gain range. 5. All hold, ramp-up and ramp-down times scale proportionally with MCLK 6. Signal-to-noise ratio (dB) – SNR is a measure of the difference in level between the full scale output and the output with no signal applied. (No Auto-zero or Automute function is employed in achieving these results). 7. THD+N (dB) – THD+N is a ratio, of the rms values, of (Noise + Distortion)/Signal. 8. Channel Separation (dB) – Also known as Cross-Talk. This is a measure of the amount one channel is isolated from the other. Measured by applying a full scale signal to one channel input and measuring the level of signal apparent at the other channel output. 9. The maximum output voltage can be limited by the speaker power supply. If OUT3BOOST, OUT4BOOST or SPKBOOST is set then SPKVDD should be 1.5xAVDD to prevent clipping taking place in the output stage (when PGA gains are set to 0dB). w PP, Rev 3.8, May 2012 10 WM8980 Pre-Production SPEAKER OUTPUT THD VERSUS POWER Speaker Power vs THD+N (8Ohm BTL Load) AVDD=SPKVDD=DBVDD=3.3, DCVDD=1.8 0 -10 -20 THD+N (dB) -30 -40 -50 -60 -70 -80 -90 -100 0.00 50.00 100.00 150.00 200.00 250.00 300.00 350.00 400.00 450.00 500.00 700.00 800.00 900.00 1000.00 Output Power (mW) Speaker Power vs THD+N (8Ohm BTL Load) AVDD=DBVDD=3.3V, SPKVDD=5V, DCVDD=1.8V 0 -10 -20 THD+N (dB) -30 -40 -50 -60 -70 -80 -90 -100 0.00 100.00 200.00 300.00 400.00 500.00 600.00 Output Power (mW) Speaker Power vs THD+N with +6dB Gain on LOUT2/ROUT2 (8Ohm BTL Load) AVDD=DBVDD=3.3V, SPKVDD=5V, DCVDD=1.8V 0 -10 -20 THD+N (dB) -30 -40 -50 -60 -70 -80 -90 -100 0.00 200.00 400.00 600.00 800.00 1000.00 1200.00 1400.00 Output Power (mW) w PP, Rev 3.8, May 2012 11 WM8980 Pre-Production POWER CONSUMPTION Typical current consumption for various scenarios is shown below. MODE AVDD DCVDD DBVDD (3.0V) (1.9V) (3.0V) (mA) 3 Off Sleep (VREF maintained, no clocks) MIC Record (8kHz) 2 Stereo 16Ω HP Playback (48kHz, quiescent) 2 Stereo 16Ω HP Playback (48kHz, white noise) Stereo 16Ω HP Playback (48kHz, sine wave) 2 (mA) 1 VBVDD TOTAL (3.0V) POWER (mA) (mA) (mW) 0.04 0.0008 <0.0001 0 0.12 0.04 0.0008 <0.0001 0 0.12 4.1 1.0 0.001 0 14.1 3.3 6.2 0.004 0 21.1 29.4 5.4 7.3 0.004 0 2 18 6.7 0.004 0 66.1 2 18 6.7 0.004 4.0 78.1 Stereo 16Ω HP Playback (48kHz, sine wave) video buffer enabled Table 1 Power Consumption Notes: 1. DBVDD Current will increase with greater loading on digital I/O pins. 2. 5 Band EQ is enabled. 3. AVDD standby current will fall to nearer 15uA when thermal shutdown sensor is disabled. ESTIMATING SUPPLY CURRENT When either the DAC or ADC is enabled approximately 7mA will be drawn from DCVDD when DCVDD=1.8V and fs=48kHz. When the PLL is enabled approximately 1.5mA additional current will be drawn from DCVDD. The video buffer will draw approximately 4mA with no load attached. During normal operation up to 30mA will be drawn. As a general rule, digital supply currents will scale in proportion to sample rates. Supply current for analogue and digital blocks will also be lower at lower supply voltages. Power consumed by the output drivers will depend greatly on the signal characteristics. A quiet signal, or a signal with long periods of silence will consume less power than a signal which is continuously loud. w PP, Rev 3.8, May 2012 12 WM8980 Pre-Production Estimated supply current for the analogue blocks is shown in Table 2. Note that power dissipated in the load is not shown. REGISTER BIT AVDD CURRENT (mA) AVDD=3.3V BUFDCOPEN 0.1 OUT4MIXEN 0.2 OUT3MIXEN 0.2 PLLEN 1.2 (with clocks applied) MICBEN 0.5 BIASEN 0.3 BUFIOEN 0.1 VMIDSEL 0.3 (5k VMID) <0.1 (75k or 300k VMID) ROUT1EN 0.4 LOUT1EN 0.4 BOOSTENR 0.2 BOOSTENL 0.2 INPPGAENR 0.2 INPPGAENL 0.2 ADCENR 2.6 (x64, ADCOSR=0) ADCENL 2.6 (x64, ADCOSR=0) 4.9 ( x128, ADCOSR=1) 4.9 ( x128, ADCOSR=1) OUT4EN 0.2 OUT3EN 0.2 LOUT2EN 1mA from SPKVDD + 0.2mA from AVDD in 5V mode ROUT2EN 1mA from SPKVDD + 0.2mA from AVDD in 5V mode RMIXEN 0.2 LMIXEN 0.2 DACENR 1.8 (x64, DACOSR=0) DACENL 1.8 (x64, DACOSR=0) 1.9 (x128, DACOSR=1) 1.9 (x128, DACOSR=1) Table 2 AVDD Supply Current (AVDD=3.3V) w PP, Rev 3.8, May 2012 13 WM8980 Pre-Production AUDIO PATHS OVERVIEW w PP, Rev 3.8, May 2012 14 WM8980 Pre-Production SIGNAL TIMING REQUIREMENTS SYSTEM CLOCK TIMING tMCLKL MCLK tMCLKH tMCLKY Figure 1 System Clock Timing Requirements Test Conditions o DCVDD=1.8V, DBVDD=AVDD=SPKVDD=3.3V, DGND=AGND=SPKGND=0V, TA = +25 C PARAMETER SYMBOL CONDITIONS MIN TMCLKY MCLK=SYSCLK (=256fs) TYP MAX UNIT System Clock Timing Information MCLK cycle time MCLK duty cycle MCLK input to PLL TMCLKDS Note 1 81.38 ns 20 ns 40:60 60:40 Note 1: PLL pre-scaling and PLL N and K values should be set appropriately so that SYSCLK is no greater than 12.288MHz. AUDIO INTERFACE TIMING – MASTER MODE Figure 2 Digital Audio Data Timing – Master Mode (see Control Interface) w PP, Rev 3.8, May 2012 15 WM8980 Pre-Production Test Conditions o DCVDD=1.8V, DBVDD=AVDD=SPKVDD=3.3V, DGND=AGND=SPKGND=0V, TA=+25 C, Master Mode, fs=48kHz, MCLK=256fs, 24-bit data, unless otherwise stated. PARAMETER SYMBOL MIN TYP MAX UNIT Audio Data Input Timing Information LRC propagation delay from BCLK falling edge tDL 10 ns ADCDAT propagation delay from BCLK falling edge tDDA 10 ns DACDAT setup time to BCLK rising edge tDST 10 ns DACDAT hold time from BCLK rising edge tDHT 10 ns AUDIO INTERFACE TIMING – SLAVE MODE Figure 3 Digital Audio Data Timing – Slave Mode Test Conditions o DCVDD=1.8V, DBVDD=AVDD=SPKVDD=3.3V, DGND=AGND=SPKGND=0V, TA=+25 C, Slave Mode, fs=48kHz, MCLK= 256fs, 24-bit data, unless otherwise stated. PARAMETER SYMBOL MIN TYP MAX UNIT Audio Data Input Timing Information BCLK cycle time tBCY 50 ns BCLK pulse width high tBCH 20 ns BCLK pulse width low tBCL 20 ns LRC set-up time to BCLK rising edge tLRSU 10 ns LRC hold time from BCLK rising edge tLRH 10 ns DACDAT hold time from BCLK rising edge tDH 10 ADCDAT propagation delay from BCLK falling edge tDD ns 10 ns Note: BCLK period should always be greater than or equal to MCLK period. w PP, Rev 3.8, May 2012 16 WM8980 Pre-Production CONTROL INTERFACE TIMING – 3-WIRE MODE Figure 4 Control Interface Timing – 3-Wire Serial Control Mode Test Conditions o DCVDD = 1.8V, DBVDD = AVDD = SPKVDD = 3.3V, DGND = AGND = SPKGND = 0V, TA=+25 C, Slave Mode, fs=48kHz, MCLK = 256fs, 24-bit data, unless otherwise stated. PARAMETER SYMBOL MIN TYP MAX UNIT Program Register Input Information SCLK rising edge to CSB rising edge tSCS 80 SCLK pulse cycle time tSCY 200 ns SCLK pulse width low tSCL 80 ns SCLK pulse width high tSCH 80 ns SDIN to SCLK set-up time tDSU 40 ns SCLK to SDIN hold time tDHO 40 ns CSB pulse width low tCSL 40 ns CSB pulse width high tCSH 40 ns CSB rising to SCLK rising tCSS 40 ns tps 0 Pulse width of spikes that will be suppressed w ns 5 ns PP, Rev 3.8, May 2012 17 WM8980 Pre-Production CONTROL INTERFACE TIMING – 2-WIRE MODE t3 t3 t5 SDIN t4 t6 t2 t8 SCLK t1 t9 t7 Figure 5 Control Interface Timing – 2-Wire Serial Control Mode Test Conditions o DCVDD=1.8V, DBVDD=AVDD=SPKVDD=3.3V, DGND=AGND=SPKGND=0V, MCLK = 256fs, 24-bit data, unless otherwise stated. TA=+25 C, Slave PARAMETER SYMBOL MIN SCLK Low Pulse-Width t1 1.3 us SCLK High Pulse-Width t2 600 ns Hold Time (Start Condition) t3 600 ns Setup Time (Start Condition) t4 600 ns Data Setup Time t5 100 SDIN, SCLK Rise Time t6 SDIN, SCLK Fall Time t7 Setup Time (Stop Condition) t8 Data Hold Time t9 Pulse width of spikes that will be suppressed tps TYP Mode, fs=48kHz, MAX UNIT 526 kHz Program Register Input Information SCLK Frequency w 0 ns 300 ns 300 ns 900 ns 5 ns 600 0 ns PP, Rev 3.8, May 2012 18 WM8980 Pre-Production INTERNAL POWER ON RESET CIRCUIT Figure 6 Internal Power on Reset Circuit Schematic The WM8980 includes an internal Power-On-Reset Circuit, as shown in Figure 6, which is used reset the digital logic into a default state after power up. The POR circuit is powered from AVDD and monitors DVDD. It asserts PORB low if AVDD or DVDD is below a minimum threshold. Figure 7 Typical Power up Sequence where AVDD is Powered before DVDD Figure 7 shows a typical power-up sequence where AVDD comes up first. When AVDD goes above the minimum threshold, Vpora, there is enough voltage for the circuit to guarantee PORB is asserted low and the chip is held in reset. In this condition, all writes to the control interface are ignored. Now AVDD is at full supply level. Next DVDD rises to Vpord_on and PORB is released high and all registers are in their default state and writes to the control interface may take place. On power down, where AVDD falls first, PORB is asserted low whenever AVDD drops below the minimum threshold Vpora_off. w PP, Rev 3.8, May 2012 19 WM8980 Pre-Production Figure 8 Typical Power up Sequence where DVDD is Powered before AVDD Figure 8 shows a typical power-up sequence where DVDD comes up first. First it is assumed that DVDD is already up to specified operating voltage. When AVDD goes above the minimum threshold, Vpora, there is enough voltage for the circuit to guarantee PORB is asserted low and the chip is held in reset. In this condition, all writes to the control interface are ignored. When AVDD rises to Vpora_on, PORB is released high and all registers are in their default state and writes to the control interface may take place. On power down, where DVDD falls first, PORB is asserted low whenever DVDD drops below the minimum threshold Vpord_off. SYMBOL MIN TYP MAX UNIT Vpora 0.4 0.6 0.8 V Vpora_on 0.9 1.2 1.6 V Vpora_off 0.4 0.6 0.8 V Vpord_on 0.5 0.7 0.9 V Vpord_off 0.4 0.6 0.8 V Table 3 Typical POR Operation (typical values, not tested) Notes: w 1. If AVDD and DVDD suffer a brown-out (i.e. drop below the minimum recommended operating level but do not go below Vpora_off or Vpord_off) then the chip will not reset and will resume normal operation when the voltage is back to the recommended level again. 2. The chip will enter reset at power down when AVDD or DVDD falls below Vpora_off or Vpord_off. This may be important if the supply is turned on and off frequently by a power management system. 3. The minimum tpor period is maintained even if DVDD and AVDD have zero rise time. This specification is guaranteed by design rather than test. PP, Rev 3.8, May 2012 20 WM8980 Pre-Production DEVICE DESCRIPTION INTRODUCTION The WM8980 is a low power audio codec combining a high quality stereo audio DAC and ADC, with flexible line and microphone input and output processing. Applications for this device include multimedia phones, stereo digital camcorders, and digital still cameras with either mono or stereo, audio and video, record and playback capability. The integrated video buffer makes the device suitable for driving both audio and video signals directly to a television or VCR. FEATURES The chip offers great flexibility in use, and so can support many different modes of operation as follows: MICROPHONE INPUTS Two pairs of stereo microphone inputs are provided, allowing a pair of stereo microphones to be pseudo-differentially connected, with user defined gain using internal resistors. The provision of the common mode input pin for each stereo input allows for rejection of common mode noise on the microphone inputs (level depends on gain setting chosen). A microphone bias is output from the chip which can be used to bias both microphones. The signal routing can be configured to allow manual adjustment of mic levels, or to allow the ALC loop to control the level of mic signal that is transmitted. Total gain through the microphone paths of up to +55.25dB can be selected. PGA AND ALC OPERATION A programmable gain amplifier is provided in the input path to the ADC. This may be used manually or in conjunction with a mixed analogue/digital automatic level control (ALC) which keeps the recording volume constant. LINE INPUTS (AUXL, AUXR) The inputs, AUXL and AUXR, can be used as a stereo line input or as an input for warning tones (or ‘beeps’) etc. These inputs can be summed into the record paths, along with the microphone preamp outputs, so allowing for mixing of audio with ‘backing music’ etc as required. ADC The stereo ADC uses a 24-bit delta sigma oversampling architecture to deliver optimum performance with low power consumption. HI-FI DAC The hi-fi DAC provides high quality audio playback suitable for all portable audio hi-fi type applications, including MP3 players and portable disc players of all types. OUTPUT MIXERS Flexible mixing is provided on the outputs of the device. A stereo mixer is provided for the stereo headphone or line outputs, LOUT1/ROUT1, and additional summers on the OUT3/OUT4 outputs allow for an optional differential or stereo line output on these pins. Gain adjustment PGAs are provided for the LOUT1/ROUT1 and LOUT2/ROUT2 outputs, and signal switching is provided to allow for all possible signal combinations. The output buffers can be configured in several ways, allowing support of up to three sets of external transducers; ie stereo headphone, BTL speaker, and BTL earpiece may be connected simultaneously. Thermal implications should be considered before simultaneous full power operation of all outputs is attempted. Alternatively, if a speaker output is not required, the LOUT2 and ROUT2 pins might be used as a stereo headphone driver, (disable output invert buffer on ROUT2). In that case two sets of headphones might be driven, or the LOUT2 and ROUT2 pins used as a line output driver. w PP, Rev 3.8, May 2012 21 WM8980 Pre-Production OUT3 and OUT4 can be configured to provide an additional stereo lineout from the output of the DACs, the mixers or the input microphone boost stages. Alternatively OUT4 can be configured as a mono mix of left and right DACs or mixers, or simply a buffered version of the chip midrail reference voltage. OUT3 can also be configured as a buffered VMID output. This voltage may then be used as a headphone ‘pseudo ground’ allowing removal of the large AC coupling capacitors often used in the output path. AUDIO INTERFACES The WM8980 has a standard audio interface, to support the transmission of stereo data to and from the chip. This interface is a 3 wire standard audio interface which supports a number of audio data formats including I2S, DSP/PCM Mode (a burst mode in which LRC sync plus 2 data packed words are transmitted), MSB-First, left justified and MSB-First, right justified, and can operate in master or slave modes. CONTROL INTERFACES To allow full software control over all features, the WM8980 offers a choice of 2 or 3 wire control interface. It is fully compatible and an ideal partner for a wide range of industry standard microprocessors, controllers and DSPs. Selection between the modes is via the MODE pin. In 2 wire mode the address of the device is fixed as 0011010. CLOCKING SCHEMES WM8980 offers the normal audio DAC clocking scheme operation, where 256fs MCLK is provided to the DAC and ADC. A PLL is included which may be used to generate these clocks in the event that they are not available from the system controller. This PLL uses an input clock, typically the 12MHz USB or ilink clock, to generate high quality audio clocks. If this PLL is not required for generation of these clocks, it can be reconfigured to generate alternative clocks which may then be output on the GPIO pins and used elsewhere in the system. VIDEO BUFFER rd The WM8980 incorporates a current mode output video buffer with an input 3 order Low Pass Filter (LPF) and clamp. The gain through this buffer can be programmed as 0dB or 6dB via the control interface. The current mode output means that the signal swing seen at the output of the buffer will be the same as that at the connection to the receiving equipment (e.g. a TV). Note that the input to the receiver should be AC coupled and terminated to 75, as is standard, for best performance. POWER CONTROL The design of the WM8980 has given much attention to power consumption without compromising performance. It operates at very low voltages, and includes the ability to power off any unused parts of the circuitry under software control, and includes standby and power off modes. OPERATION SCENARIOS Flexibility in the design of the WM8980 allows for a wide range of operational scenarios, some of which are proposed below: Multimedia phone; High quality playback to a stereo headset, a mono ear speaker or a loudspeaker is supported, allowing hi-fi playback to be mixed with voice and other analogue inputs while simultaneously transmitting a differential output from the microphone amplifier. A 5-band EQ enables hi-fi playback to be customised to suit the user’s preferences and the music style, while programmable filtering allows fixed-frequency noise (e.g. 217Hz) to be reduced in the digital domain. Video playback directly to TV is supported using the integrated video buffer. w PP, Rev 3.8, May 2012 22 WM8980 Pre-Production Stereo Camcorder; The provision of two stereo microphone preamplifiers, allows support for both internal and external microphones. All drivers for speaker, headphone and line output connections are integrated. The selectable ‘application filters’ after the ADC provide for features such as ‘wind noise’ reduction, or mechanical noise reducing filters. The integrated video buffer allows direct connection to a TV or VCR for both video and audio (via line outputs). Stereo Digital still camera recording; Support for digital stereo video with audio recording is similar to the camcorder case. But additionally if the DSC supports MP3 playback, and perhaps recording, the ability of the ADCs to support full 48ks/s high quality stereo recording increases device flexibility. The integrated video buffer allows direct connection to the TV for display of moving and still images. Mono Digital still camera; Full control over device functionality, and power control is provided, allowing for the case of mono DSC recording, when half of the ADC and mic and line functionality may be disabled to save power. In the mono case, the single ADC channel of audio data is sent out over the Left channel of the audio interface. In the case where DSP mode is used, and mono data is being sent, only the signal channel of mono data is sent. The integrated video buffer allows direct connection to the TV for display of moving and still images. AUXILIARY ANALOGUE INPUTS An analogue stereo FM tuner or other auxiliary analogue input can be connected to the Line inputs of WM8980, and the stereo signal listened to via headphones, or recorded, simultaneously if required. INPUT SIGNAL PATH The WM8980 has a number of flexible analogue inputs. There are two input channels, Left and Right, each of which consists of an input PGA stage followed by a boost/mix stage which drives into the hi-fi ADC. Each input path has three input pins which can be configured in a variety of ways to accommodate single-ended, differential or dual differential microphones. There are two auxiliary input pins which can be fed into to the input boost/mix stage as well as driving into the output path. A bypass path exists from the output of the boost/mix stage into the output left/right mixers. MICROPHONE INPUTS The WM8980 can accommodate a variety of microphone configurations including single ended and differential inputs. The inputs to the left differential input PGA are LIN, LIP and L2. The inputs to the right differential input PGA are RIN, RIP and R2. In single-ended microphone input configuration the microphone signal should be input to LIN or RIN and the internal NOR gate configured to clamp the non-inverting input of the input PGA to VMID. In differential mode the larger signal should be input to LIP or RIP and the smaller (e.g. noisy ground connection) should be input to LIN or RIN. Figure 9 Microphone Input PGA Circuit w PP, Rev 3.8, May 2012 23 WM8980 Pre-Production The input PGAs are enabled by the IPPGAENL/R register bits. REGISTER ADDRESS BIT LABEL 2 R2 DEFAULT INPPGAENL 0 DESCRIPTION Left channel input PGA enable 0 = disabled Power Management 2 1 = enabled 3 INPPGAENR 0 Right channel input PGA enable 0 = disabled 1 = enabled Table 4 Input PGA Enable Register Settings REGISTER ADDRESS BIT R44 0 LABEL LIP2INPPGA DEFAULT 1 Input Control DESCRIPTION Connect LIP pin to left channel input PGA amplifier positive terminal. 0 = LIP not connected to input PGA 1 = input PGA amplifier positive terminal connected to LIP (constant input impedance) 1 LIN2INPPGA 1 Connect LIN pin to left channel input PGA negative terminal. 0=LIN not connected to input PGA 1=LIN connected to input PGA amplifier negative terminal. 2 L2_2INPPGA 0 Connect L2 pin to left channel input PGA positive terminal. 0=L2 not connected to input PGA 1=L2 connected to input PGA amplifier positive terminal (constant input impedance). 4 RIP2INPPGA 1 Connect RIP pin to right channel input PGA amplifier positive terminal. 0 = RIP not connected to input PGA 1 = right channel input PGA amplifier positive terminal connected to RIP (constant input impedance) 5 RIN2INPPGA 1 Connect RIN pin to right channel input PGA negative terminal. 0=RIN not connected to input PGA 1=RIN connected to right channel input PGA amplifier negative terminal. 6 R2_2INPPGA 0 Connect R2 pin to right channel input PGA positive terminal. 0=R2 not connected to input PGA 1=R2 connected to input PGA amplifier positive terminal (constant input impedance). Table 5 Input PGA Control INPUT PGA VOLUME CONTROLS The input microphone PGAs have a gain range from -12dB to +35.25dB in 0.75dB steps. The gain from the LIN/RIN input to the PGA output and from the L2/R2 amplifier to the PGA output are always common and controlled by the register bits INPPGAVOLL/R[5:0]. These register bits also affect the LIP pin when LIP2INPPGA=1, the L2 pin when L2_2INPPGA=1, the RIP pin when RIP2INPPGA=1 and the L2 pin when L2_2INPPGA=1. When the Automatic Level Control (ALC) is enabled the input PGA gains are controlled automatically and the INPPGAVOLL/R bits should not be used. w PP, Rev 3.8, May 2012 24 WM8980 Pre-Production REGISTER ADDRESS BIT R45 5:0 LABEL INPPGAVOLL DEFAULT 010000 DESCRIPTION Left channel input PGA volume 000000 = -12dB Left channel input PGA volume control 000001 = -11.25db . 010000 = 0dB . 111111 = 35.25dB 6 INPPGAMUTEL 0 Mute control for left channel input PGA: 0=Input PGA not muted, normal operation 1=Input PGA muted (and disconnected from the following input BOOST stage). 7 INPPGAZCL 0 Left channel input PGA zero cross enable: 0=Update gain when gain register changes st 1=Update gain on 1 zero cross after gain register write. R46 8 INPPGAUPDATE Not latched 5:0 INPPGAVOLR 010000 INPPGAVOLL and INPPGAVOLR volume do not update until a 1 is written to INPPGAUPDATE (in reg 45 or 46) Right channel input PGA volume 000000 = -12dB Right channel input PGA volume control 000001 = -11.25db . 010000 = 0dB . 111111 = +35.25dB 6 INPPGAMUTER 0 Mute control for right channel input PGA: 0=Input PGA not muted, normal operation 1=Input PGA muted (and disconnected from the following input BOOST stage). 7 INPPGAZCR 0 Right channel input PGA zero cross enable: 0=Update gain when gain register changes st 1=Update gain on 1 zero cross after gain register write. R32 8 INPPGAUPDATE Not latched 8:7 ALCSEL 00 ALC control 1 INPPGAVOLL and INPPGAVOLR volume do not update until a 1 is written to INPPGAUPDATE (in reg 45 or 46) ALC function select: 00=ALC off 01=ALC right only 10=ALC left only 11=ALC both on Table 6 Input PGA Volume Control w PP, Rev 3.8, May 2012 25 WM8980 Pre-Production VOLUME UPDATES Volume settings will not be applied to the PGAs until a ‘1’ is written to one of the INPPGAUPDATE bits. This is to allow left and right channels to be updated at the same time, as shown in Figure 10. Figure 10 Simultaneous Left and Right Volume Updates If the volume is adjusted while the signal is a non-zero value, an audible click can occur as shown in Figure 11. Figure 11 Click Noise During Volume Update In order to prevent this click noise, a zero cross function is provided. When enabled, this will cause the PGA volume to update only when a zero crossing occurs, minimising click noise as shown in Figure 12. w PP, Rev 3.8, May 2012 26 WM8980 Pre-Production Figure 12 Volume Update Using Zero Cross Detection If there is a long period where no zero-crossing occurs, a timeout circuit in the WM8980 will automatically update the volume. The volume updates will occur between one and two timeout periods, depending on when the INPPGAUPDATE bit is set as shown in Figure 13. Figure 13 Volume Update after Timeout w PP, Rev 3.8, May 2012 27 WM8980 Pre-Production AUXILLIARY INPUTS There are two auxiliary inputs, AUXL and AUXR which can be used for a variety of purposes such as stereo line inputs or as a ‘beep’ input signal to be mixed with the outputs. The AUXL/R inputs can be used as a line input to the input BOOST stage which has gain adjust of 12dB to +6dB in 3dB steps (plus off). See the INPUT BOOST section for further details. The AUXL/R inputs can also be mixed into the output channel mixers, with a gain of -15dB to +6dB plus off. In addition the AUXR input can be summed into the Right speaker output path (ROUT2) with a gain adjust of -15 to +6dB. This allows a ‘beep’ input to be output on the speaker outputs only without affecting the headphone or lineout signals. INPUT BOOST Each of the stereo input PGA stages is followed by an input BOOST circuit. The input BOOST circuit has 3 selectable inputs: the input microphone PGA output, the AUX amplifier output and the L2/R2 input pin (can be used as a line input, bypassing the input PGA). These three inputs can be mixed together and have individual gain boost/adjust as shown in Figure 14. Figure 14 Input Boost Stage The input PGA paths can have a +20dB boost (PGABOOSTL/R=1) , a 0dB pass through (PGABOOSTL/R=0) or be completely isolated from the input boost circuit (INPPGAMUTEL/R=1). REGISTER ADDRESS R47 BIT 8 LABEL PGABOOSTL DEFAULT 1 Left Input BOOST control DESCRIPTION Boost enable for left channel input PGA: 0 = PGA output has +0dB gain through input BOOST stage. 1 = PGA output has +20dB gain through input BOOST stage. R48 8 PGABOOSTR Right Input BOOST control 1 Boost enable for right channel input PGA: 0 = PGA output has +0dB gain through input BOOST stage. 1 = PGA output has +20dB gain through input BOOST stage. Table 7 Input BOOST Stage Control w PP, Rev 3.8, May 2012 28 WM8980 Pre-Production The Auxiliary amplifier path to the BOOST stages is controlled by the AUXL2BOOSTVOL[2:0] and AUXR2BOOSTVOL[2:0] register bits. When AUXL2BOOSTVOL/AUXR2BOOSTVOL=000 this path is completely disconnected from the BOOST stage. Settings 001 through to 111 control the gain in 3dB steps from -12dB to +6dB. The L2/R2 path to the BOOST stage is controlled by the LIP2BOOSTVOL[2:0] and the RIP2BOOSTVOL[2:0] register bits. When L2_2BOOSTVOL/R2_2BOOSTVOL=000 the L2/R2 input pin is completely disconnected from the BOOST stage. Settings 001 through to 111 control the gain in 3dB steps from -12dB to +6dB. REGISTER ADDRESS R47 BIT 2:0 LABEL AUXL2BOOSTVOL DEFAULT 000 Left channel Input BOOST control DESCRIPTION Controls the auxiliary amplifer to the left channel input boost stage: 000=Path disabled (disconnected) 001=-12dB gain through boost stage 010=-9dB gain through boost stage … 111=+6dB gain through boost stage 6:4 L2_2BOOSTVOL 000 Controls the L2 pin to the left channel input boost stage: 000=Path disabled (disconnected) 001=-12dB gain through boost stage 010=-9dB gain through boost stage … 111=+6dB gain through boost stage R48 2:0 AUXR2BOOSTVOL 000 Right channel Input BOOST control Controls the auxiliary amplifer to the right channel input boost stage: 000=Path disabled (disconnected) 001=-12dB gain through boost stage 010=-9dB gain through boost stage … 111=+6dB gain through boost stage 6:4 R2_2BOOSTVOL 000 Controls the R2 pin to the right channel input boost stage: 000=Path disabled (disconnected) 001=-12dB gain through boost stage 010=-9dB gain through boost stage … 111=+6dB gain through boost stage Table 8 Input BOOST Stage Control w PP, Rev 3.8, May 2012 29 WM8980 Pre-Production The BOOST stage is enabled under control of the BOOSTEN register bit. REGISTER ADDRESS BIT LABEL 4 R2 Power management 2 DEFAULT BOOSTENL 0 DESCRIPTION Left channel Input BOOST enable 0 = Boost stage OFF 1 = Boost stage ON 5 BOOSTENR 0 Right channel Input BOOST enable 0 = Boost stage OFF 1 = Boost stage ON Table 9 Input BOOST Enable Control MICROPHONE BIASING CIRCUIT The MICBIAS output provides a low noise reference voltage suitable for biasing electret type microphones and the associated external resistor biasing network. Refer to the Applications Information section for recommended external components. The MICBIAS voltage can be altered via the MBVSEL register bit. When MBVSEL=0, MICBIAS=0.9*AVDD and when MBVSEL=1, MICBIAS=0.65*AVDD. The output can be enabled or disabled using the MICBEN control bit. REGISTER ADDRESS BIT R1 4 LABEL DEFAULT MICBEN 0 Power management 1 DESCRIPTION Microphone Bias Enable 0 = OFF (high impedance output) 1 = ON Table 10 Microphone Bias Enable Control REGISTER ADDRESS R44 BIT 8 LABEL MBVSEL DEFAULT 0 Input control DESCRIPTION Microphone Bias Voltage Control 0 = 0.9 * AVDD 1 = 0.65 * AVDD Table 11 Microphone Bias Voltage Control The internal MICBIAS circuitry is shown in Figure 15. Note that the maximum source current capability for MICBIAS is 3mA. The external biasing resistors therefore must be large enough to limit the MICBIAS current to 3mA. Figure 15 Microphone Bias Schematic w PP, Rev 3.8, May 2012 30 WM8980 Pre-Production ANALOGUE TO DIGITAL CONVERTER (ADC) The WM8980 uses stereo multi-bit, oversampled sigma-delta ADCs. The use of multi-bit feedback and high oversampling rates reduces the effects of jitter and high frequency noise. The ADC Full Scale input level is proportional to AVDD. With a 3.3V supply voltage, the full scale level is 1.0Vrms. Any voltage greater than full scale may overload the ADC and cause distortion. ADC DIGITAL FILTERS The ADC filters perform true 24 bit signal processing to convert the raw multi-bit oversampled data from the ADC to the correct sampling frequency to be output on the digital audio interface. The digital filter path for each ADC channel is illustrated in Figure 16. Figure 16 ADC Digital Filter Path The ADCs are enabled by the ADCENL/R register bit. REGISTER ADDRESS R2 BIT 0 LABEL ADCENL DEFAULT 0 DESCRIPTION Enable ADC left channel: Power management 2 0 = ADC disabled 1 = ADC enabled 1 ADCENR 0 Enable ADC right channel: 0 = ADC disabled 1 = ADC enabled Table 12 ADC Enable Control The polarity of the output signal can also be changed under software control using the ADCLPOL/ADCRPOL register bit. The oversampling rate of the ADC can be adjusted using the ADCOSR register bit. With ADCOSR=0 the oversample rate is 64x which gives lowest power operation and when ADCOSR=1 the oversample rate is 128x which gives best performance. REGISTER ADDRESS R14 BIT 0 LABEL ADCLPOL DEFAULT 0 ADC Control DESCRIPTION ADC left channel polarity adjust: 0=normal 1=inverted 1 ADCRPOL 0 ADC right channel polarity adjust: 0=normal 1=inverted 3 ADCOSR 0 ADC oversample rate select: 0=64x (lower power) 1=128x (best performance) Table 13 ADC Control w PP, Rev 3.8, May 2012 31 WM8980 Pre-Production SELECTABLE HIGH PASS FILTER A selectable high pass filter is provided. To disable this filter set HPFEN=0. The filter has two modes controlled by HPFAPP. In Audio Mode (HPFAPP=0) the filter is first order, with a cut-off frequency of 3.7Hz. In Application Mode (HPFAPP=1) the filter is second order, with a cut-off frequency selectable via the HPFCUT register. The cut-off frequencies when HPFAPP=1 are shown in Table 15. REGISTER ADDRESS BIT R14 LABEL 8 HPFEN DEFAULT 1 DESCRIPTION High Pass Filter Enable ADC Control 0=disabled 7 HPFAPP 1=enabled Select audio mode or application mode 0 st 0=Audio mode (1 order, fc = ~3.7Hz) nd 1=Application mode (2 order, fc = HPFCUT) 6:4 HPFCUT 000 Application mode cut-off frequency See Table 15 for details. Table 14 ADC Enable Control HPFCUT SR=101/100 SR=011/010 [2:0] SR=001/000 fs (kHz) 8 11.025 12 16 22.05 24 32 44.1 48 000 82 113 122 82 113 122 82 113 122 001 102 141 153 102 141 153 102 141 153 010 131 180 196 131 180 196 131 180 196 011 163 225 245 163 225 245 163 225 245 100 204 281 306 204 281 306 204 281 306 101 261 360 392 261 360 392 261 360 392 110 327 450 490 327 450 490 327 450 490 111 408 563 612 408 563 612 408 563 612 Table 15 High Pass Filter Cut-off Frequencies (HPFAPP=1). Values in Hz. Note that the High Pass filter values (when HPFAPP=1) are calculated with the assumption that the SR register bits are set correctly for the actual sample rate as shown in Table 15. w PP, Rev 3.8, May 2012 32 WM8980 Pre-Production PROGRAMMABLE NOTCH FILTER A programmable notch filter is provided. This filter has a variable centre frequency and bandwidth, programmable via two coefficients, a0 and a1. The coefficients must be entered in 2’s complement notation. A0 and a1 are represented by the register bits NFA0[13:0] and NFA1[13:0]. Because these coefficient values require four register writes to setup there is an NFU (Notch Filter Update) flag which should be set only when all four registers are setup. REGISTER ADDRESS BIT R27 6:0 Notch Filter 1 7 LABEL DEFAULT DESCRIPTION NFA0[13:7] 0 Notch Filter a0 coefficient, bits [13:7] NFEN 0 Notch filter enable: 0=Disabled 1=Enabled 8 NFU 0 Notch filter update. The notch filter values used internally only update when one of the NFU bits is set high. R28 6:0 NFA0[6:0] 0 Notch Filter a0 coefficient, bits [6:0] Notch Filter 2 8 NFU 0 Notch filter update. The notch filter values used internally only update when one of the NFU bits is set high. R29 6:0 NFA1[13:7] 0 Notch Filter a1 coefficient, bits [13:7] Notch Filter 3 8 NFU 0 Notch filter update. The notch filter values used internally only update when one of the NFU bits is set high. R30 0-6 Notch Filter 4 8 NFA1[6:0] 0 Notch Filter a1 coefficient, bits [6:0] NFU 0 Notch filter update. The notch filter values used internally only update when one of the NFU bits is set high. Table 16 Notch Filter Function The coefficients are calculated as follows: a0 1 tan( wb / 2) 1 tan( wb / 2) a1 (1 a0 ) cos( w0 ) Where: w0 2f c / f s wb 2f b / f s fc = centre frequency in Hz, fb = -3dB bandwidth in Hz, fs = sample frequency in Hz The actual register values can be determined from the coefficients as follows: 13 NFA0 = -a0 x 2 12 NFA1 = -a1 x 2 NOTCH FILTER WORKED EXAMPLE The following example illustrates how to calculate the a0 and a1 coefficients for a desired centre frequency and -3dB bandwidth. w PP, Rev 3.8, May 2012 33 WM8980 Pre-Production Fc = 1000 Hz fb = 100 Hz fs = 48000 Hz w0 2f c / f s = 2 x (1000 / 48000) = 0.1308996939 rads wb 2f b / f s = 2 x (100 / 48000) = 0.01308996939 rads a0 1 tan( wb / 2) 1 tan( wb / 2) = 1 tan(0.01308996939 / 2) 1 tan(0.01308996939 / 2) = 0.9869949627 a1 (1 a0 ) cos(w0 ) = (1 0.9869949627) cos(0.1308996939) = -1.969995945 NFA0 = -a0 x 213 = -8085 (rounded to nearest whole number) NFA1 = -a1 x 212 = 8069 (rounded to nearest whole number) These values are then converted to a 2’s complement notation: NfnA0[12:0] = 13’h1F95; Converting to 2’s complement NFA0 = 14’h4000 – 14’h1F95 = 14’h206B NfnA1[12:0] = 13’h1F85; Converting to 2’s complement NFA0 = 14’h1F85 DIGITAL ADC VOLUME CONTROL The output of the ADCs can be digitally attenuated over a range from –127dB to 0dB in 0.5dB steps. The gain for a given eight-bit code X is given by: 0.5 (G-255) dB for 1 G 255; REGISTER ADDRESS R15 BIT 7:0 Left channel ADC Digital Volume LABEL MUTE for G = 0 DEFAULT DESCRIPTION ADCVOLL 11111111 Left ADC Digital Volume Control [7:0] ( 0dB ) 0000 0000 = Digital Mute 0000 0001 = -127dB 0000 0010 = -126.5dB … 0.5dB steps up to 1111 1111 = 0dB R16 8 ADCVU Not latched ADC left and ADC right volume do not update until a 1 is written to ADCVU (in reg 15 or 16) 7:0 ADCVOLR 11111111 Right ADC Digital Volume Control [7:0] ( 0dB ) 0000 0000 = Digital Mute Right channel ADC Digital Volume 0000 0001 = -127dB 0000 0010 = -126.5dB … 0.5dB steps up to 1111 1111 = 0dB 8 ADCVU Not latched ADC left and ADC right volume do not update until a 1 is written to ADCVU (in reg 15 or 16) Table 17 ADC Digital Volume Control w PP, Rev 3.8, May 2012 34 WM8980 Pre-Production INPUT LIMITER / AUTOMATIC LEVEL CONTROL (ALC) The WM8980 has an automatic PGA gain control circuit, which can function as an input peak limiter or as an automatic level control (ALC). The Automatic Level Control (ALC) provides continuous adjustment of the input PGA in response to the amplitude of the input signal. A digital peak detector monitors the input signal amplitude and compares it to a register defined threshold level (ALCLVL). If the signal is below the threshold, the ALC will increase the gain of the PGA at a rate set by ALCDCY. If the signal is above the threshold, the ALC will reduce the gain of the PGA at a rate set by ALCATK. The ALC has two modes selected by the ALCMODE register: normal mode and peak limiter mode. The ALC/limiter function is enabled by setting the register bit R32[8] ALCSEL. REGISTER ADDRESS R32 (20h) BIT 2:0 ALC Control 1 LABEL ALCMIN DEFAULT 000 (-12dB) [2:0] DESCRIPTION Set minimum gain of PGA 000 = -12dB 001 = -6dB 010 = 0dB 011 = +6dB 100 = +12dB 101 = +18dB 110 = +24dB 111 = +30dB 5:3 ALCMAX [2:0] 111 (+35.25dB) Set Maximum Gain of PGA 111 = +35.25dB 110 = +29.25dB 101 = +23.25dB 100 = +17.25dB 011 = +11.25dB 010 = +5.25dB 001 = -0.75dB 000 = -6.75dB 8:7 ALCSEL 00 ALC function select 00 = ALC disabled 01 = Right channel ALC enabled 10 = Left channel ALC enabled 11 = Both channels ALC enabled R33 (21h) ALC Control 2 3:0 ALCLVL 1011 [3:0] (-6dB) ALC target – sets signal level at ADC input 1111 = -1.5dBFS 1110 = -1.5dBFS 1101 = -3dBFS 1100 = -4.5dBFS 1011 = -6dBFS 1010 = -7.5dBFS 1001 = -9dBFS 1000 = -10.5dBFS 0111 = -12dBFS 0110 = -13.5dBFS 0101 = -15dBFS 0100 = -16.5dBFS 0011 = -18dBFS 0010 = -19.5dBFS 0001 = -21dBFS 0000 = -22.5dBFS w PP, Rev 3.8, May 2012 35 WM8980 Pre-Production REGISTER ADDRESS BIT 8 LABEL ALCZC DEFAULT 0 DESCRIPTION ALC Zero Cross Control 0 = ALCZC off 1 = ALCZC on (only valid when ALCMODE=0. ALCZC should not be used when ALCMODE=1) 7:4 ALCHLD 0000 [3:0] (0ms) ALC hold time before gain is increased. 0000 = 0ms 0001 = 2.67ms 0010 = 5.33ms 0011 = 10.66ms 0100 = 21.32ms 0101 = 42.64ms 0110 = 85.28ms 0111 = 0.17s 1000 = 0.34s 1001 = 0.68s 1010 or higher = 1.36s R34 (22h) 8 ALCMODE 0 ALC Control 3 Determines the ALC mode of operation: 0 = ALC mode (Normal Operation) 1 = Limiter mode. 7:4 ALCDCY 0011 Decay (gain ramp-up) time [3:0] (26ms/6dB) (ALCMODE ==0) Per step Per 6dB 90% of range 0000 410us 3.28ms 23.6ms 0001 820us 6.56ms 47.2ms 0010 1.64ms 13.1ms 94.5ms … (time doubles with every step) 1010 or higher 420ms 3.36s 0011 Decay (gain ramp-up) time (5.8ms/6dB) (ALCMODE ==1) Per step Per 6dB 24.2s 90% of range 0000 90.8us 726us 5.23ms 0001 182us 1.45ms 10.5ms 0010 363us 2.91ms 20.9ms … (time doubles with every step) 1010 3:0 93ms 744ms 5.36s ALCATK 0010 ALC attack (gain ramp-down) time [3:0] (3.3ms/6dB) (ALCMODE == 0) Per step Per 6dB 90% of range 0000 104us 832us 6ms 0001 208us 1.66ms 12ms 0010 416us 3.33ms 24ms … (time doubles with every step) 1010 or higher w 106ms 852ms 6.13s 0010 ALC attack (gain ramp-down) time (726us/6dB) (ALCMODE == 1) PP, Rev 3.8, May 2012 36 WM8980 Pre-Production REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION Per step Per 6dB 90% of range 0000 22.7us 182us 1.31ms 0001 45.4us 363us 2.62ms 0010 90.8us 726us 5.23ms … (time doubles with every step) 1010 or higher 23.2ms 186ms 1.34s Table 18 ALC Control Registers WHEN THE ALC IS DISABLED, THE INPUT PGA REMAINS AT THE LAST CONTROLLED VALUE OF THE ALC. AN INPUT GAIN UPDATE MUST BE MADE BY WRITING TO THE INPPGAVOLL/R REGISTER BITS. NORMAL MODE In normal mode, the ALC will attempt to maintain a constant signal level by increasing or decreasing the gain of the PGA. The following diagram shows an example of this. Figure 17 ALC Normal Mode Operation w PP, Rev 3.8, May 2012 37 WM8980 Pre-Production LIMITER MODE In limiter mode, the ALC will reduce peaks that go above the threshold level, but will not increase the PGA gain beyond the starting level. The starting level is the PGA gain setting when the ALC is enabled in limiter mode. If the ALC is started in limiter mode, this is the gain setting of the PGA at start-up. If the ALC is switched into limiter mode after running in ALC mode, the starting gain will be the gain at switchover. The diagram below shows an example of limiter mode. Figure 18 ALC Limiter Mode Operation ALC LIMITER MODE INITIALISATION SEQUENCE In order to properly initialise the ALC function, the following sequence of register writes is required: 1. Set INPPGAVOLL to the required input PGA gain (R45[5:0]). 2. Enable analogue inputs (R44[2:0]) as required. 3. Disable INPPGAENL (R2[2] =0). 4. Set ALCMAXGAIN (R32[5:3]) and ALCMINGAIN (R32[2:0]) to the required level for operation. 5. Set ALCLVL (R33[3:0]) to the required level for operation. 6. Set R34 to 0x000. 7. Wait for 1ms to allow the input PGA gain to update by the limiter circuit. 8. Enable Limiter mode (R34[8]=1). 9. Wait for 1ms to allow the input PGA gain to update by the limiter circuit. 10. Enable INPPGAENL (R2[2] =1). w PP, Rev 3.8, May 2012 38 WM8980 Pre-Production ATTACK AND DECAY TIMES The attack and decay times set the update times for the PGA gain. The attack time is the time constant used when the gain is reducing. The decay time is the time constant used when the gain is increasing. In limiter mode, the time constants are faster than in ALC mode. The time constants are shown below in terms of a single gain step, a change of 6dB and a change of 90% of the PGAs gain range. Note that, these times will vary slightly depending on the sample rate used (specified by the SR register). NORMAL MODE ALCMODE = 0 (Normal Mode) Attack Time (s) ALCATK 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 tATK 104µs 208µs 416µs 832µs 1.66ms 3.33ms 6.66ms 13.3ms 26.6ms 53.2ms 106ms tATK6dB 832µs 1.66ms 3.33ms 6.66ms 13.3ms 26.6ms 53.2ms 106ms 213.2ms 426ms 852ms tATK90% 6ms 12ms 24ms 48ms 96ms 192ms 384ms 767ms 1.53s 3.07s 6.13s ALCMODE = 0 (Normal Mode) ALCDCY 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 tDCY 410µs 820µs 1.64ms 3.28ms 6.56ms 13.1ms 26.2ms 52.5ms 105ms 210ms 420ms Decay Time (s) tDCY6dB tDCY90% 3.28ms 23.6ms 6.56ms 47.2ms 13.1ms 94.5ms 26.2ms 189ms 52.5ms 378ms 105ms 756ms 210ms 1.51s 420ms 3.02s 840ms 6.05s 1.68s 12.1s 3.36s 24.2s Table 19 ALC Normal Mode (Attack and Decay times) w PP, Rev 3.8, May 2012 39 WM8980 Pre-Production LIMITER MODE ALCMODE = 1 (Limiter Mode) ALCATK 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 tATKLIM 22.7µs 45.4µS 90.8µS 182µS 363µS 726µS 1.45ms 2.9ms 5.81ms 11.6ms 23.2ms Attack Time (s) tATKLIM6dB tATKLIM90% 182µs 1.31ms 363µs 2.62ms 726µs 5.23ms 1.45ms 10.5ms 2.91ms 20.9ms 5.81ms 41.8ms 11.6ms 83.7ms 23.2ms 167ms 46.5ms 335ms 93ms 669ms 186ms 1.34s ALCMODE = 1 (Limiter Mode) ALCDCY 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 tDCYLIM 90.8µs 182µS 363µS 726µS 1.45ms 2.91ms 5.81ms 11.6ms 23.2ms 46.5ms 93ms Attack Time (s) tDCYLIM6dB tDCYLIM90% 726µs 5.23ms 1.45ms 10.5ms 2.91ms 20.9ms 5.81ms 41.8ms 11.6ms 83.7ms 23.2ms 167ms 46.5ms 335ms 93ms 669ms 186ms 1.34s 372ms 2.68s 744ms 5.36s Table 20 ALC Limiter Mode (Attack and Decay times) w PP, Rev 3.8, May 2012 40 WM8980 Pre-Production MINIMUM AND MAXIMUM GAIN The ALCMIN and ALCMAX register bits set the minimum/maximum gain value that the PGA can be set to whilst under the control of the ALC. This has no effect on the PGA when ALC is not enabled. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R32 5:3 ALCMAX 111 Set Maximum Gain of PGA ALC Control 1 2:0 ALCMIN 000 Set minimum gain of PGA Table 21 ALC Max/Min Gain In normal mode, ALCMAX sets the maximum boost which can be applied to the signal. In limiter mode, ALCMAX will normally have no effect (assuming the starting gain value is less than the maximum gain specified by ALCMAX) because the maximum gain is set at the starting gain level. ALCMIN sets the minimum gain value which can be applied to the signal. Figure 19 ALC Min/Max Gain ALCMAX 111 110 101 100 011 010 001 000 Maximum Gain (dB) 35.25 29.25 23.25 17.25 11.25 5.25 -0.75 -6.75 Table 22 ALC Max Gain Values w PP, Rev 3.8, May 2012 41 WM8980 Pre-Production ALCMIN 000 001 010 011 100 101 110 111 Minimum Gain (dB) -12 -6 0 6 12 18 24 30 Table 23 ALC Min Gain Values Note that if the ALC gain setting strays outside the ALC operating range, either by starting the ALC outside of the range or changing the ALCMAX or ALCMIN settings during operation, the ALC will immediately adjust the gain to return to the ALC operating range. It is recommended that the ALC starting gain is set between the ALCMAX and ALCMIN limits. ALC HOLD TIME (NORMAL MODE ONLY) In Normal mode, the ALC has an adjustable hold time which sets a time delay before the ALC begins its decay phase (gain increasing). The hold time is set by the ALCHLD register. REGISTER ADDRESS R33 BIT 7:4 LABEL ALCHLD DEFAULT 0000 DESCRIPTION ALC hold time before gain is increased. ALC Control 2 Table 24 ALC Hold Time If the hold time is exceeded this indicates that the signal has reached a new average level and the ALC will increase the gain to adjust for that new average level. If the signal goes above the threshold during the hold period, the hold phase is abandoned and the ALC returns to normal operation. w PP, Rev 3.8, May 2012 42 Pre-Production WM8980 Figure 20 ALCLVL w PP, Rev 3.8, May 2012 43 WM8980 Pre-Production Figure 21 ALC Hold Time ALCHLD 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 tHOLD (s) 0 2.67ms 5.34ms 10.7ms 21.4ms 42.7ms 85.4ms 171ms 342ms 684ms 1.37s Table 25 ALC Hold Time Values w PP, Rev 3.8, May 2012 44 WM8980 Pre-Production PEAK LIMITER To prevent clipping when a large signal occurs just after a period of quiet, the ALC circuit includes a limiter function. If the ADC input signal exceeds 87.5% of full scale (–1.16dB), the PGA gain is ramped down at the maximum attack rate (as when ALCATK = 0000), until the signal level falls below 87.5% of full scale. This function is automatically enabled whenever the ALC is enabled. (Note: If ALCATK = 0000, then the limiter makes no difference to the operation of the ALC. It is designed to prevent clipping when long attack times are used). NOISE GATE When the signal is very quiet and consists mainly of noise, the ALC function may cause “noise pumping”, i.e. loud hissing noise during silence periods. The WM8980 has a noise gate function that prevents noise pumping by comparing the signal level at the input pins against a noise gate threshold, NGTH. The noise gate cuts in when: Signal level at ADC [dBFS] < NGTH [dBFS] + PGA gain [dB] + Mic Boost gain [dB] This is equivalent to: Signal level at input pin [dBFS] < NGTH [dBFS] The PGA gain is then held constant (preventing it from ramping up as it normally would when the signal is quiet). The table below summarises the noise gate control register. The NGTH control bits set the noise gate threshold with respect to the ADC full-scale range. The threshold is adjusted in 6dB steps. Levels at the extremes of the range may cause inappropriate operation, so care should be taken with set–up of the function. The noise gate only operates in conjunction with the ALC and cannot be used in limiter mode. REGISTER ADDRESS R35 BIT 2:0 LABEL NGTH DEFAULT 000 DESCRIPTION Noise gate threshold: ALC Noise Gate 000=-39dB Control 001=-45dB 010=-51db … (6dB steps) 111=-81dB 3 NGEN 0 Noise gate function enable 1 = enable 0 = disable Table 26 ALC Noise Gate Control w PP, Rev 3.8, May 2012 45 WM8980 Pre-Production The diagrams below show the response of the system to the same signal with and without noise gate. Figure 22 ALC Operation Above Noise Gate Threshold w PP, Rev 3.8, May 2012 46 WM8980 Pre-Production Figure 23 Noise Gate Operation OUTPUT SIGNAL PATH The WM8980 output signal paths consist of digital application filters, up-sampling filters, stereo Hi-Fi DACs, analogue mixers, speaker, stereo headphone and stereo line/mono/midrail output drivers. The digital filters and DAC are enabled by register bits DACENL And DACENR. The mixers and output drivers can be separately enabled by individual control bits (see Analogue Outputs). Thus it is possible to utilise the analogue mixing and amplification provided by the WM8980, irrespective of whether the DACs are enabled or not. The WM8980 DACs receive digital input data on the DACDAT pin. The digital filter block processes the data to provide the following functions: Digital volume control Graphic equaliser Digital peak limiter. Sigma-Delta Modulation High performance sigma-delta 24-bit audio DAC converts the digital data into an analogue signal. w PP, Rev 3.8, May 2012 47 WM8980 Pre-Production Figure 24 DAC Digital Filter Path The analogue outputs from the DACs can then be mixed with the aux analogue inputs and the ADC analogue inputs. The mix is fed to the output drivers for headphone (LOUT1/ROUT1), speaker (LOUT2/ROUT2) or line (OUT3/OUT4). OUT3 and OUT4 have additional mixers which allow them to output different signals to the headphone and speaker outputs. DIGITAL PLAYBACK (DAC) PATH Digital data is passed to the WM8980 via the flexible audio interface and is then passed through a variety of advanced digital filters (as shown in Figure 24) to the hi-fi DACs. The DACs are enabled by the DACENL/R register bits. REGISTER ADDRESS R3 BIT 0 LABEL DACENL DEFAULT 0 Power Management 3 DESCRIPTION Left channel DAC enable 0 = DAC disabled 1 = DAC enabled 1 DACENR 0 Right channel DAC enable 0 = DAC disabled 1 = DAC enabled Table 27 DAC Enable Control The WM8980 also has a Soft Mute function, which, when enabled, gradually attenuates the volume of the digital signal to zero. When disabled, the gain will ramp back up to the digital gain setting. This function is enabled by default. To play back an audio signal, this function must first be disabled by setting the SOFTMUTE bit to zero. REGISTER ADDRESS R10 BIT LABEL 0 DACPOLL DEFAULT 0 DAC Control DESCRIPTION Left DAC output polarity: 0 = non-inverted 1 = inverted (180 degrees phase shift) 1 DACPOLR 0 Right DAC output polarity: 0 = non-inverted 1 = inverted (180 degrees phase shift) 2 AMUTE 0 Automute enable 0 = Amute disabled 1 = Amute enabled 3 DACOSR128 0 DAC oversampling rate select: 0=64x (lowest power) 1=128x (best SNR) 6 SOFTMUTE 0 Softmute enable: 0=Enabled 1=Disabled Table 28 DAC Control Register The digital audio data is converted to oversampled bit streams in the on-chip, true 24-bit digital interpolation filters. The bitstream data enters the multi-bit, sigma-delta DACs, which convert it to a high quality analogue audio signal. The multi-bit DAC architecture reduces high frequency noise and sensitivity to clock jitter. It also uses a Dynamic Element Matching technique for high linearity and low distortion. w PP, Rev 3.8, May 2012 48 WM8980 Pre-Production The DAC output phase defaults to non-inverted. Setting DACPOLL will invert the DAC output phase on the left channel and DACPOLR inverts the phase on the right channel. AUTO-MUTE The DAC has an auto-mute function which applies an analogue mute when 1024 consecutive zeros are detected. The mute is released as soon as a non-zero sample is detected. Automute can be disabled using the AMUTE control bit. DIGITAL HI-FI DAC VOLUME (GAIN) CONTROL The signal volume from each Hi-Fi DAC can be controlled digitally. The gain and attenuation range is –127dB to 0dB in 0.5dB steps. The level of attenuation for an eight-bit code X is given by: 0.5 (X-255) dB for 1 X 255; REGISTER ADDRESS R11 BIT 7:0 Left DAC Digital Volume LABEL MUTE for X = 0 DEFAULT DESCRIPTION DACVOLL 11111111 Left DAC Digital Volume Control [7:0] ( 0dB ) 0000 0000 = Digital Mute 0000 0001 = -127dB 0000 0010 = -126.5dB ... 0.5dB steps up to 1111 1111 = 0dB R12 8 DACVU Not latched DAC left and DAC right volume do not update until a 1 is written to DACVU (in reg 11 or 12) 7:0 DACVOLR 11111111 Right DAC Digital Volume Control [7:0] ( 0dB ) 0000 0000 = Digital Mute Right DAC Digital Volume 0000 0001 = -127dB 0000 0010 = -126.5dB ... 0.5dB steps up to 1111 1111 = 0dB 8 DACVU Not latched DAC left and DAC right volume do not update until a 1 is written to DACVU (in reg 11 or 12) Table 29 DAC Digital Volume Control Note: An additional gain of up to +12dB can be added using the gain block embedded in the digital peak limiter circuit (see DAC OUTPUT LIMITER section). 5-BAND EQUALISER A 5-band graphic equaliser function which can be used to change the output frequency levels to suit the environment. This can be applied to the ADC or DAC path and is described in the 5-BAND EQUALISER section for further details on this feature. 3-D ENHANCEMENT The WM8980 has an advanced digital 3-D enhancement feature which can be used to vary the perceived stereo separation of the left and right channels. Like the 5-band equaliser this feature can be applied to either the ADC record path or the DAC playback path but not both simultaneously. See the 3-D STEREO ENHANCEMENT section for further details on this feature. DAC DIGITAL OUTPUT LIMITER The WM8980 has a digital output limiter function. The operation of this is shown in Figure 25. In this diagram the upper graph shows the envelope of the input/output signals and the lower graph shows the gain characteristic. w PP, Rev 3.8, May 2012 49 WM8980 Pre-Production Figure 25 DAC Digital Limiter Operation The limiter has a programmable upper threshold which is close to 0dB. Referring to Figure 25, in normal operation (LIMBOOST=000 => limit only) signals below this threshold are unaffected by the limiter. Signals above the upper threshold are attenuated at a specific attack rate (set by the LIMATK register bits) until the signal falls below the threshold. The limiter also has a lower threshold 1dB below the upper threshold. When the signal falls below the lower threshold the signal is amplified at a specific decay rate (controlled by LIMDCY register bits) until a gain of 0dB is reached. Both threshold levels are controlled by the LIMLVL register bits. The upper threshold is 0.5dB above the value programmed by LIMLVL and the lower threshold is 0.5dB below the LIMLVL value. VOLUME BOOST The limiter has programmable upper gain which boosts signals below the threshold to compress the dynamic range of the signal and increase its perceived loudness. This operates as an ALC function with limited boost capability. The volume boost is from 0dB to +12dB in 1dB steps, controlled by the LIMBOOST register bits. The output limiter volume boost can also be used as a stand alone digital gain boost when the limiter is disabled. w PP, Rev 3.8, May 2012 50 WM8980 Pre-Production REGISTER ADDRESS R24 BIT 3:0 LABEL LIMATK DEFAULT 0010 DAC digital limiter control 1 DESCRIPTION Limiter Attack time (per 6dB gain change) for 44.1kHz sampling. Note that these will scale proportionally with sample rate. 0000=94us 0001=188s 0010=375us 0011=750us 0100=1.5ms 0101=3ms 0110=6ms 0111=12ms 1000=24ms 1001=48ms 1010=96ms 1011 to 1111=192ms 7:4 LIMDCY 0011 Limiter Decay time (per 6dB gain change) for 44.1kHz sampling. Note that these will scale proportionally with sample rate: 0000=750us 0001=1.5ms 0010=3ms 0011=6ms 0100=12ms 0101=24ms 0110=48ms 0111=96ms 1000=192ms 1001=384ms 1010=768ms 1011 to 1111=1.536s 8 LIMEN 0 Enable the DAC digital limiter: 0=disabled 1=enabled R25 DAC digital limiter control 2 3:0 LIMBOOST 0000 Limiter volume boost (can be used as a stand alone volume boost when LIMEN=0): 0000=0dB 0001=+1dB 0010=+2dB … (1dB steps) 1011=+11dB 1100=+12dB 1101 to 1111=reserved w PP, Rev 3.8, May 2012 51 WM8980 Pre-Production REGISTER ADDRESS BIT 6:4 LABEL LIMLVL DEFAULT 000 DESCRIPTION Programmable signal threshold level (determines level at which the limiter starts to operate) 000=-1dB 001=-2dB 010=-3dB 011=-4dB 100=-5dB 101 to 111=-6dB Table 30 DAC Digital Limiter Control 5-BAND GRAPHIC EQUALISER A 5-band graphic equaliser (EQ) is provided, which can be applied to the ADC or DAC path, together with 3D enhancement, under control of the EQ3DMODE register bit. REGISTER ADDRESS R18 BIT 8 LABEL EQ3DMODE DEFAULT 1 EQ Control 1 DESCRIPTION 0 = Equaliser and 3D Enhancement applied to ADC path 1 = Equaliser and 3D Enhancement applied to DAC path Table 31 EQ and 3D Enhancement DAC or ADC Path Select The equaliser consists of low and high frequency shelving filters (Band 1 and 5) and three peak filters for the centre bands. Each has adjustable cut-off or centre frequency, and selectable boost (+/- 12dB in 1dB steps). The peak filters have selectable bandwidth. REGISTER ADDRESS R18 BIT 4:0 LABEL EQ1G EQ Band 1 Control 6:5 EQ1C DEFAULT 01100 DESCRIPTION (0dB) Band 1 Gain Control. See Table 37 for details. 01 Band 1 Cut-off Frequency: 00=80Hz 01=105Hz 10=135Hz 11=175Hz Table 32 EQ Band 1 Control REGISTER ADDRESS R19 BIT 4:0 LABEL EQ2G EQ Band 2 Control 6:5 EQ2C DEFAULT 01100 DESCRIPTION (0dB) Band 2 Gain Control. See Table 37 for details. 01 Band 2 Centre Frequency: 00=230Hz 01=300Hz 10=385Hz 8 EQ2BW 0 11=500Hz Band 2 Bandwidth Control 0=narrow bandwidth 1=wide bandwidth Table 33 EQ Band 2 Control w PP, Rev 3.8, May 2012 52 WM8980 Pre-Production REGISTER ADDRESS R20 BIT 4:0 LABEL EQ3G EQ Band 3 Control 6:5 EQ3C DEFAULT 01100 DESCRIPTION (0dB) Band 3 Gain Control. See Table 37 for details. 01 Band 3 Centre Frequency: 00=650Hz 01=850Hz 10=1.1kHz 8 EQ3BW 11=1.4kHz Band 3 Bandwidth Control 0 0=narrow bandwidth 1=wide bandwidth Table 34 EQ Band 3 Control REGISTER ADDRESS R21 BIT 4:0 LABEL EQ4G EQ Band 4 Control 6:5 EQ4C DEFAULT 01100 DESCRIPTION (0dB) Band 4 Gain Control. See Table 37 for details 01 Band 4 Centre Frequency: 00=1.8kHz 01=2.4kHz 10=3.2kHz 8 EQ4BW 11=4.1kHz Band 4 Bandwidth Control 0 0=narrow bandwidth 1=wide bandwidth Table 35 EQ Band 4 Control REGISTER ADDRESS R22 BIT 4:0 LABEL EQ5G EQ Band 5 Gain Control 6:5 EQ5C DEFAULT 01100 DESCRIPTION (0dB) Band 5 Gain Control. See Table 37 for details. 01 Band 5 Cut-off Frequency: 00=5.3kHz 01=6.9kHz 10=9kHz 11=11.7kHz Table 36 EQ Band 5 Control GAIN REGISTER GAIN 00000 +12dB 00001 +11dB 00010 +10dB …. (1dB steps) 01100 0dB 01101 -1dB 11000 -12dB 11001 to 11111 Reserved Table 37 Gain Register Table w PP, Rev 3.8, May 2012 53 WM8980 Pre-Production 3D STEREO ENHANCEMENT The WM8980 has a digital 3D enhancement option to increase the perceived separation between the left and right channels. Selection of 3D for record or playback is controlled by register bit EQ3DMODE. Switching this bit from record to playback or from playback to record may only be done when ADC and DAC are disabled. The WM8980 control interface will only allow EQ3DMODE to be changed when ADC and DAC are disabled (ie ADCENL = 0, ADCENR = 0, DACENL = 0 and DACENR = 0). The DEPTH3D setting controls the degree of stereo expansion. When 3D enhancement is used, it may be necessary to attenuate the signal by 6dB to avoid limiting. REGISTER ADDRESS R41 (29h) BIT 3:0 LABEL DEPTH3D[3:0] DEFAULT 0000 3D DESCRIPTION Stereo depth 0000: 0% (minimum 3D effect) 0001: 6.67% .... 1110: 93.3% 1111: 100% (maximum 3D effect) Table 38 3D Stereo Enhancement Function ANALOGUE OUTPUTS The WM8980 has three sets of stereo analogue outputs. These are: LOUT1 and ROUT1 which are normally used to drive a headphone load. LOUT2 and ROUT2 – normally used to drive an 8Ω BTL speaker. OUT3 and OUT4 – can be configured as a stereo line out (OUT3 is left output and OUT4 is right output). OUT4 can also be used to provide a mono mix of left and right channels. LOUT2, ROUT2, OUT3 and OUT4 are supplied from SPKVDD and are capable of driving up to 1.5Vrms signals as shown in Figure 26. LOUT1 and ROUT1 are supplied from AVDD and can only drive out a 1V rms signal (AVDD/3.3). LOUT1, ROUT1, LOUT2 and ROUT2 have individual analogue volume PGAs with -57dB to +6dB ranges. There are four output mixers in the output signal path, the left and right channel mixers which control the signals to speaker, headphone (and optionally the line outputs) and also dedicated OUT3 and OUT4 mixers. LEFT AND RIGHT OUTPUT CHANNEL MIXERS The left and right output channel mixers are shown in Figure 26. These mixers allow the AUX inputs, the ADC bypass and the DAC left and right channels to be combined as desired. This allows a mono mix of the DAC channels to be done as well as mixing in external line-in from the AUX or speech from the input bypass path. The AUX and bypass inputs have individual volume control from -15dB to +6dB and the DAC volume can be adjusted in the digital domain if required. The output of these mixers is connected to both the headphone (LOUT1 and ROUT1) and speaker (LOUT2 and ROUT2) and can optionally be connected to the OUT3 and OUT4 mixers. w PP, Rev 3.8, May 2012 54 WM8980 Pre-Production Figure 26 Left/Right Output Channel Mixers w PP, Rev 3.8, May 2012 55 WM8980 Pre-Production REGISTER ADDRESS R49 BIT 5 LABEL DACR2LMIX DEFAULT DESCRIPTION 0 Right DAC output to left output mixer Output mixer control 0 = not selected 1 = selected 6 DACL2RMIX 0 Left DAC output to right output mixer 0 = not selected 1 = selected R50 Left channel output mixer control 0 DACL2LMIX 1 Left DAC output to left output mixer 0 = not selected 1 = selected 1 BYPL2LMIX 0 Left bypass path (from the left channel input boost output) to left output mixer 0 = not selected 1 = selected 4:2 BYPLMIXVOL 000 Left bypass volume control to output channel mixer: 000 = -15dB 001 = -12dB … 101 = 0dB 110 = +3dB 111 = +6dB 5 AUXL2LMIX 0 Left Auxiliary input to left channel output mixer: 0 = not selected 1 = selected 8:6 AUXLMIXVOL 000 Aux left channel input to left mixer volume control: 000 = -15dB 001 = -12dB … 101 = 0dB 110 = +3dB 111 = +6dB w PP, Rev 3.8, May 2012 56 WM8980 Pre-Production REGISTER ADDRESS R51 BIT 0 LABEL DACR2RMIX DEFAULT 1 Right channel output mixer control DESCRIPTION Right DAC output to right output mixer 0 = not selected 1 = selected 1 BYPR2RMIX 0 Right bypass path (from the right channel input boost output) to right output mixer 0 = not selected 1 = selected 4:2 BYPRMIXVOL 000 Right bypass volume control to output channel mixer: 000 = -15dB 001 = -12dB … 101 = 0dB 110 = +3dB 111 = +6dB 5 AUXR2RMIX 0 Right Auxiliary input to right channel output mixer: 0 = not selected 1 = selected 8:6 AUXRMIXVOL 000 Aux right channel input to right mixer volume control: 000 = -15dB 001 = -12dB … 101 = 0dB 110 = +3dB 111 = +6dB R3 Power management 3 2 LMIXEN 0 Left output channel mixer enable: 0 = disabled 1= enabled 3 RMIXEN 0 Right output channel mixer enable: 0 = disabled 1 = enabled Table 39 Left and Right Output Mixer Control HEADPHONE OUTPUTS (LOUT1 AND ROUT1) The headphone outputs, LOUT1 and ROUT1 can drive a 16 or 32 headphone load, either through DC blocking capacitors, or DC coupled without any capacitor. Each headphone output has an analogue volume control PGA with a gain range of -57dB to +6dB as shown in Figure 29. w PP, Rev 3.8, May 2012 57 WM8980 Pre-Production Figure 27 Headphone Outputs LOUT1 and ROUT1 REGISTER ADDRESS R52 BIT 7 LABEL LOUT1ZC DEFAULT 0 LOUT1 DESCRIPTION Headphone volume zero cross enable: 1 = Change gain on zero cross only Volume control 0 = Change gain immediately 6 LOUT1MUTE 0 Left headphone output mute: 0 = Normal operation 1 = Mute 5:0 LOUT1VOL 111001 Left headphone output volume: 000000 = -57dB ... 111001 = 0dB ... 111111 = +6dB R53 8 HPVU 7 ROUT1ZC Not latched 0 ROUT1 Volume control LOUT1 and ROUT1 volumes do not update until a 1 is written to HPVU (in reg 52 or 53) Headphone volume zero cross enable: 1 = Change gain on zero cross only 0 = Change gain immediately 6 ROUT1MUTE 0 Right headphone output mute: 0 = Normal operation 1 = Mute 5:0 ROUT1VOL 111001 Right headphone output volume: 000000 = -57dB ... 111001 = 0dB ... 111111 = +6dB 8 HPVU Not latched LOUT1 and ROUT1 volumes do not update until a 1 is written to HPVU (in reg 52 or 53) Table 40 OUT1 Volume Control w PP, Rev 3.8, May 2012 58 WM8980 Pre-Production Headphone Output using DC Blocking Capacitors: DC Coupled Headphone Output: Figure 28 Recommended Headphone Output Configurations When DC blocking capacitors are used, then their capacitance and the load resistance together determine the lower cut-off frequency, fc. Increasing the capacitance lowers fc, improving the bass response. Smaller capacitance values will diminish the bass response. Assuming a 16 load and C1, C2 = 220F: fc = 1 / 2 RLC1 = 1 / (2 x 16 x 220F) = 45 Hz In the DC coupled configuration, the headphone “ground” is connected to the VMID pin. The OUT3/4 pins can be configured as a DC output driver by setting the OUT3MUTE and OUT4MUTE register bit. The DC voltage on VMID in this configuration is equal to the DC offset on the LOUT1 and ROUT1 pins therefore no DC blocking capacitors are required. This saves space and material cost in portable applications. Note that OUT3 and OUT4 have an optional output boost of 1.5x. When these are configured in this output boost mode (OUT3BOOST/OUT4BOOST=1) then the VMID value of these outputs will be equal to 1.5xAVDD/2 and will not match the VMID of the headphone drivers. Do not use the DC coupled output mode in this configuration. It is recommended to connect the DC coupled outputs only to headphones, and not to the line input of another device. Although the built-in short circuit protection will prevent any damage to the headphone outputs, such a connection may be noisy, and may not function properly if the other device is grounded. SPEAKER OUTPUTS (LOUT2 AND ROUT2) The outputs LOUT2 and ROUT2 are designed to drive an 8Ω BTL speaker but can optionally drive two headphone loads of 16/32 or a line output (see Headphone Output and Line Output sections, respectively). Each output has an individual volume control PGA, an output boost/level shift bit, a mute and an enable as shown in Figure 29. LOUT2 and ROUT2 output the left and right channel mixer outputs respectively. The ROUT2 signal path also has an optional invert. The amplifier used for this invert can be used to mix in the AUXR signal with an adjustable gain range of -15dB -> +6dB. This allows a ‘beep’ signal to be applied only to the speaker output without affecting the HP or line outputs. w PP, Rev 3.8, May 2012 59 WM8980 Pre-Production Figure 29 Speaker Outputs LOUT2 and ROUT2 w PP, Rev 3.8, May 2012 60 WM8980 Pre-Production REGISTER ADDRESS R54 LOUT2 (SPK) Volume control BIT 7 LABEL LOUT2ZC DEFAULT 0 DESCRIPTION Speaker volume zero cross enable: 1 = Change gain on zero cross only 0 = Change gain immediately 6 LOUT2MUTE 0 Left speaker output mute: 0 = Normal operation 1 = Mute 5:0 LOUT2VOL 111001 Left speaker output volume: 000000 = -57dB ... 111001 = 0dB ... 111111 = +6dB R55 ROUT2 (SPK) Volume control 8 SPKVU 7 ROUT2ZC Not latched LOUT2 and ROUT2 volumes do not update until a 1 is written to SPKVU (in reg 54 or 55) 0 Speaker volume zero cross enable: 1 = Change gain on zero cross only 0 = Change gain immediately 6 ROUT2MUTE 0 Right speaker output mute: 0 = Normal operation 1 = Mute 5:0 ROUT2VOL 111001 Right speaker output volume: 000000 = -57dB ... 111001 = 0dB ... 111111 = +6dB 8 SPKVU Not latched LOUT2 and ROUT2 volumes do not update until a 1 is written to SPKVU (in reg 54 or 55) Table 41 Speaker Volume Control The signal output on LOUT2/ROUT2 comes from the Left/Right Mixer circuits and can be any combination of the DAC output, the Bypass path (output of the input boost stage) and the AUX input. The LOUT2/ROUT2 volume is controlled by the LOUT2VOL/ ROUT2VOL register bits. Gains over 0dB may cause clipping if the signal is large. The LOUT2MUTE/ ROUT2MUTE register bits cause the speaker outputs to be muted (the output DC level is driven out). The output pins remain at the same DC level (DCOP), so that no click noise is produced when muting or un-muting The speaker output stages also have a selectable gain boost of 1.5x (3.52dB). When this boost is enabled the output DC level is also level shifted (from AVDD/2 to 1.5xAVDD/2) to prevent the signal from clipping. A dedicated amplifier BUFDCOP, as shown in Figure 30, is used to perform the DC level shift operation. This buffer must be enabled using the BUFDCOPEN register bit for this operating mode. It should also be noted that if SPKVDD is not equal to or greater than 1.5xAVDD this boost mode may result in signals clipping. Table 43 summarises the effect of the SPKBOOST control bits. Note: When boost mode is selected, it is necessary to set LOUT2MUTE (R54[6]) and ROUT2MUTE (R55[6]) bits for either output to be muted w PP, Rev 3.8, May 2012 61 WM8980 Pre-Production REGISTER ADDRESS R49 BIT 2 LABEL DEFAULT SPKBOOST 0 DESCRIPTION 0 = speaker gain = -1; Output control DC = AVDD / 2 1 = speaker gain = +1.5; DC = 1.5 x AVDD / 2 8 R1 BUFDCOPEN 0 Dedicated buffer for DC level shifting output stages when in 1.5x gain boost configuration. Power management 1 0=Buffer disabled 1=Buffer enabled (required for 1.5x gain boost) Table 42 Speaker Boost Stage Control SPKBOOST OUTPUT STAGE GAIN OUTPUT DC OUTPUT STAGE CONFIGURATION 0 1x (0dB) AVDD/2 Inverting 1 1.5x (3.52dB) 1.5xAVDD/2 Non-inverting LEVEL Table 43 Output Boost Stage Details REGISTER ADDRESS BIT LABEL DEFAULT R43 5 MUTERPGA2INV 0 Beep control 4 INVROUT2 0 3:1 BEEPVOL 000 DESCRIPTION Mute input to INVROUT2 mixer Invert ROUT2 output AUXR input to ROUT2 inverter gain 000 = -15dB ... 111 = +6dB 0 BEEPEN 0 0 = mute AUXR beep input 1 = enable AUXR beep input Table 44 AUXR – ROUT2 BEEP Mixer Function w PP, Rev 3.8, May 2012 62 WM8980 Pre-Production ZERO CROSS TIMEOUT A zero-cross timeout function is also provided so that if zero cross is enabled on the input or output PGAs the gain will automatically update after a timeout period if a zero cross has not occurred. This is enabled by setting SLOWCLKEN. The timeout period is dependent on the clock input to the digital 21 and is equal to 2 * input clock period. REGISTER ADDRESS R7 BIT 0 LABEL SLOWCLKEN DEFAULT 0 Additional Control DESCRIPTION Slow clock enable. Used for both the jack insert detect debounce circuit and the zero cross timeout. 0 = slow clock disabled 1 = slow clock enabled Table 45 Timeout Clock Enable Control OUT3/OUT4 MIXERS AND OUTPUT STAGES The OUT3/OUT4 pins can provide an additional stereo line output, a mono output, or a pseudo ground connection for headphones. There is a dedicated analogue mixer for OUT3 and one for OUT4 as shown in Figure 31. The OUT3 and OUT4 output stages are powered from SPKVDD and SPKGND. The individually controllable outputs also incorporate an optional 1.5x boost and level shifting stage. Figure 31 OUT3 and OUT4 Mixers w PP, Rev 3.8, May 2012 63 WM8980 Pre-Production OUT3 can provide a buffered midrail headphone pseudo-ground, or a left line output. OUT4 can provide a buffered midrail headphone pseudo-ground, a right line output, or a mono mix output. REGISTER ADDRESS R56 BIT 6 LABEL OUT3MUTE DEFAULT 0 OUT3 mixer control DESCRIPTION 0 = Output stage outputs OUT3 mixer 1 = Output stage muted – drives out VMID. Can be used as VMID buffer in this mode. 3 OUT4_2OUT3 0 OUT4 mixer output to OUT3 0 = disabled 1= enabled 2 BYPL2OUT3 0 Left ADC input to OUT3 0 = disabled 1= enabled 1 LMIX2OUT3 0 Left DAC mixer to OUT3 0 = disabled 1= enabled 0 LDAC2OUT3 1 Left DAC output to OUT3 0 = disabled 1= enabled R57 6 OUT4MUTE 0 OUT4 mixer control 0 = Output stage outputs OUT4 mixer 1 = Output stage muted – drives out VMID. Can be used as VMID buffer in this mode. 5 HALFSIG 0 0=OUT4 normal output 1=OUT4 attenuated by 6dB 4 LMIX2OUT4 0 Left DAC mixer to OUT4 0 = disabled 1= enabled 3 LDAC2OUT4 0 Left DAC to OUT4 0 = disabled 1= enabled 2 BYPR2OUT4 0 Right ADC input to OUT4 0 = disabled 1= enabled 1 RMIX2OUT4 0 Right DAC mixer to OUT4 0 = disabled 1= enabled 0 RDAC2OUT4 1 Right DAC output to OUT4 0 = disabled 1= enabled Table 46 OUT3/OUT4 Mixer Registers The OUT3 and OUT4 output stages each have a selectable gain boost of 1.5x (3.52dB). When this boost is enabled the output DC level is also level shifted (from AVDD/2 to 1.5xAVDD/2) to prevent the signal from clipping. A dedicated amplifier BUFDCOP, as shown in Figure 32, is used to perform the DC level shift operation. This buffer must be enabled using the BUFDCOPEN register bit for this operating mode. It should also be noted that if SPKVDD is not equal to or greater than 1.5xAVDD this boost mode may result in signals clipping. Table 43 summarises the effect of the OUT3BOOST and OUT4BOOST control bits. w PP, Rev 3.8, May 2012 64 WM8980 Pre-Production Figure 33 Outputs OUT3 and OUT4 REGISTER ADDRESS R49 BIT 3 LABEL DEFAULT OUT3BOOST 0 Output control DESCRIPTION 0 = OUT3 output gain = -1; DC = AVDD / 2 1 = OUT3 output gain = +1.5 DC = 1.5 x AVDD / 2 4 OUT4BOOST 0 0 = OUT4 output gain = -1; DC = AVDD / 2 1 = OUT4 output gain = +1.5 DC = 1.5 x AVDD / 2 8 R1 BUFDCOPEN 0 Power management 1 Dedicated buffer for DC level shifting output stages when in 1.5x gain boost configuration. 0=Buffer disabled 1=Buffer enabled (required for 1.5x gain boost) Table 47 OUT3 and OUT4 Boost Stages Control OUT3BOOST/ OUT4BOOST OUTPUT STAGE GAIN OUTPUT DC LEVEL OUTPUT STAGE CONFIGURATION 0 1x AVDD/2 Inverting 1 1.5x 1.5xAVDD/2 Non-inverting Table 48 OUT3/OUT4 Output Boost Stage Details w PP, Rev 3.8, May 2012 65 WM8980 Pre-Production OUTPUT PHASING The relative phases of the analogue outputs will depend upon the following factors: 1. DACPOLL and DACPOLR invert bits: Setting these bits to 1 will invert the DAC output. 2. Mixer configuration: The polarity of the signal will depend upon the route through the mixer path. For example, DACL can be directly input to the OUT3 mixer, giving a 180° phase shift at the OUT3 mixer output. However, if DACL is input to the OUT3 mixer via the left mixer, an additional phase shift will be introduced, giving 0° phase shift at the OUT3 mixer output. 3. Output boost set-up: When 1.5x boost is enabled on an output, no phase shift occurs. When 1.5x boost is not enabled, a 180° phase shift occurs. Figure 26 shows where these phase inversions can occur in the output signal path. Figure 34 Output Signal Path Phasing w PP, Rev 3.8, May 2012 66 WM8980 Pre-Production Table 49 shows the polarities of the outputs in various configurations. Unless otherwise stated, polarity is shown with respect to left DAC output in non-inverting mode. Note that only registers relating to the mixer paths are shown here (Mixer enables, volume settings, output enables etc are not shown). ROUT2 PHASE / MAG LOUT2 PHASE / MAG ROUT1 PHASE / MAG 0 LOUT1 OUT4BOOST 0 PHASE / MAG OUT3BOOST 0 OUT3 SPKBOOST 0 PHASE / MAG INVROUT2 0 Stereo DAC playback to LOUT1/ROUT1, LOUT2/ROUT2 and OUT4 DACPOLR 0 Default: MIXER PATH REGISTERS DIFFERENT FROM DEFAULT PHASE / MAG DACPOLL CONFIGURATION 0° 0° 0° 0° 180° 180° 1 1 1 1 1 1 180° 180° 180° 0° 0° OUT4/OUT3 DACs inverted 1 1 0 0 0 0 180° 1 1 1 1 1 1 Stereo DAC playback to LOUT1/ROUT1 and LOUT2/ROUT2 and 0 0 0 1 0 0 0° 0° 0° 0° 0° 0° 1 1 1 1 1.5 1.5 180° 180° 0° 0° 180° 180° 1.5 1.5 1 1 1 1 180° 180° 0° 0° 180° 180° 1 1 1 1 1 1 180° 0° X X X X 1 1 0° 0° 0° 0° 180° 0° 1 1 1 1 1 1 0° 0° 0° 0° 0° 180° 1 1 1 1 1.5 1.5 OUT4/OUT3 (Speaker boost enabled) Stereo DAC playback to LOUT1/ROUT1 and LOUT2/ROUT2 and 0 0 0 0 1 1 OUT4/OUT3 (OUT3 and OUT4 boost enabled) Stereo playback to OUT3/OUT4 (DACs input to OUT3/OUT4 mixers via left/right mixers) 0 Differential output of right bypass path via OUT3/OUT4 (Phase shown relative to right bypass) 0 Differential output of mono mix of DACs via LOUT2/ROUT2 (e.g. BTL speaker drive) 0 High power speaker drive 0 0 0 0 0 0 LDAC2OUT3=0 RDAC2OUT4=0 LMIX2OUT3=1 RMIX2OUT4=1 0 0 0 0 0 BYPR2OUT4=1 OUT4_2OUT3=1 0 0 1 1 0 1 0 0 0 0 Table 49 Relative Output Phases Note that differential output should not be set up by combining outputs in boost mode with outputs which are not in boost mode as this would cause a DC offset current on the outputs. w PP, Rev 3.8, May 2012 67 WM8980 Pre-Production ENABLING THE OUTPUTS Each analogue output of the WM8980 can be separately enabled or disabled. The analogue mixer associated with each output has a separate enable. All outputs are disabled by default. To save power, unused parts of the WM8980 should remain disabled. The SLEEP bit should only be set on to reduce residual device currents once all the other power management bits have been set to off. Outputs can be enabled at any time, but it is not recommended to do so when BUFIO is disabled (BUFIOEN=0) or when BUFDCOP is disabled (BUFDCOPEN=0) when configured in output boost mode, as this may cause pop noise (see “Power Management” and “Applications Information” sections). REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R1 2 BUFIOEN 0 Unused input/output tie off buffer enable Power Management 1 6 OUT3MIXEN 0 OUT3 mixer enable 7 OUT4MIXEN 0 OUT4 mixer enable 8 BUFDCOPEN 0 Output stage 1.5xAVDD/2 driver enable R2 8 ROUT1EN 0 ROUT1 output enable 2 Power Management 2 2 7 LOUT1EN 0 LOUT1 output enable 6 SLEEP 0 0 = normal device operation 1 = residual current reduced in device standby mode R3 2 LMIXEN 0 Left mixer enable Power Management 3 3 RMIXEN 0 Right mixer enable 4 VBUFEN 0 Video buffer enable 5 ROUT2EN 0 ROUT2 output enable 2 6 LOUT2EN 0 LOUT2 output enable 7 OUT3EN 0 OUT3 enable 2 8 OUT4EN 0 OUT4 enable 2 2 Table 50 Output Stages Power Management Control Notes: All “Enable” bits are 1 = ON, 0 = OFF Disabling the outputs does not automatically mute the output mixers. To avoid pop noise, it is recommended that the relevant mixer is muted before disabling outputs. THERMAL SHUTDOWN The speaker outputs can drive very large currents. To protect the WM8980 from overheating a thermal shutdown circuit is included. The thermal shutdown can be configured to produce an o interrupt when the device reaches approximately 125 C. See General Purpose Input/Output section. REGISTER ADDRESS R49 BIT 1 LABEL TSDEN DEFAULT 1 Output control DESCRIPTION Thermal Shutdown Enable 0 : thermal shutdown disabled 1 : thermal shutdown enabled Table 51 Thermal Shutdown UNUSED ANALOGUE INPUTS/OUTPUTS Whenever an analogue input/output is disabled, it remains connected to a voltage source (either AVDD/2 or 1.5xAVDD/2 as appropriate) through a resistor. This helps to prevent pop noise when the output is re-enabled. The resistance between the voltage buffer and the output pins can be controlled using the VROI control bit. The default impedance is low, so that any capacitors on the outputs can charge up quickly at start-up. If a high impedance is desired for disabled outputs, VROI can then be set to 1, increasing the resistance to about 30k. w PP, Rev 3.8, May 2012 68 WM8980 Pre-Production REGISTER ADDRESS R49 BIT 0 LABEL VROI DEFAULT 0 DESCRIPTION VREF (AVDD/2 or 1.5xAVDD/2) to analogue output resistance 0: approx 1k 1: approx 30 k Table 52 Disabled Outputs to VREF Resistance A dedicated buffer is available for tying off unused analogue I/O pins as shown in Figure 35. This buffer can be enabled using the BUFIOEN register bit. If the SPKBOOST, OUT3BOOST or OUT4BOOST bits are set, then the relevant outputs will be tied to the output of the DC level shift buffer at 1.5xAVDD/2 when disabled. Figure 35 summarises the tie-off options for the speaker and mono output pins. Figure 35 Unused Input/Output Pin Tie-off Buffers w PP, Rev 3.8, May 2012 69 WM8980 Pre-Production L/ROUT2EN/ OUT3BOOST/ OUT3/4EN OUT4BOOST/ VROI OUTPUT CONFIGURATION SPKBOOST 0 0 0 1kΩ tie-off to AVDD/2 0 0 1 30kΩ tie-off to AVDD/2 0 1 0 1kΩ tie-off to 1.5xAVDD/2 0 1 1 30kΩ tie-off to 1.5xAVDD/2 1 0 X Output enabled (DC level=AVDD/2) 1 1 X Output enabled (DC level=1.5xAVDD/2) Table 53 Unused Output Pin Tie-off Options VIDEO BUFFER DESCRIPTION The WM8980 incorporates a current mode output video buffer capable of operating from a 2.5V rd supply, with an input 3 order Low Pass Filter (LPF) and clamp. The gain through this buffer can be programmed as 0dB or 6dB (=6dB or 12dB unloaded) via the control interface. The current mode output means that the signal swing seen at the output of the buffer will be the same as that at the connection to the receiving equipment (e.g. a TV). Note that the input to the receiver should be AC coupled and terminated to 75, as is standard, for best performance. Figure 36 Video Buffer The input clamp should be enabled when using AC coupling at the input to the video buffer, using the VBCLAMPEN register bit. Note: The WM8980 Video Buffer input signal level at the input pin (VBIN) should not exceed 500mV when using ac coupling or 330mV when using dc coupling when the input clamp circuit is enabled. It is therefore recommended that the video signal is ac coupled into the video buffer and that the video signal driving VBIN is disabled and is either high impedance or GND when the video buffer is disabled. Care should be taken with PCB layout, designing for at least 1GHz frequencies to avoid degrading performance. Vias and sharp corners should be avoided and parasitic capacitance minimised on signal paths, which should be kept as short and straight as possible. The VBVDD supply should be decoupled as close to the pin as possible. See the “External Components” section for more information. LOW PASS FILTER A low pass filter is integrated at the video buffer input, which is intended to remove images in the rd video DAC output waveform at multiples of the DAC clock frequency. A 3 order Butterworth filter is used, with the following characteristics: w PP, Rev 3.8, May 2012 70 WM8980 Pre-Production WM8980 Video Buffer Filter Response -20dBV sinewave input, 0dB gain setting, VBVDD=3.3V 10 0dB 0dB Qboost 6dB 6dB Qboost 5 Amplitude (dB) 0 -5 -10 -15 -20 -25 10 100 1000 10000 100000 Frequency (kHz) VIDEO BUFFER REGISTERS Video buffer enable / disable and gain are controlled via the following registers: REGISTER ADDRESS R3 BIT 4 LABEL VBUFEN DEFAULT 0 Power management 3 R40 DESCRIPTION Video buffer enable 0 = disabled 1 = enabled 0 VBCLAMPEN 0 Video Buffer Video buffer clamp enable 0 = disabled 1 = enabled 1 VBGAIN 0 Video buffer gain 0 = 0dB (=6dB unloaded) 1 = +6dB (=12dB unloaded) 4 QBOOST 0 Increases the filters Q. Table 54 Video Buffer Registers w PP, Rev 3.8, May 2012 71 WM8980 Pre-Production TEST WAVEFORMS Figure 37 Black Needle Pulse Figure 38 Dual Needle Pulse (Full frame of white with a vertical black line) (50% grey field with closely-spaced white and black vertical lines spaced across the line scan) Figure 39 Multiburst Figure 40 White Needle Pulse (A horizontal multiburst of signals with frequencies ranging from 0.5MHz to 5.75MHz) (A full frame of black with a vertical white line) CURRENT MODE OUTPUT The current mode output employed by the WM8980 video buffer allows VBVDD to operate at lower voltages than voltage mode video buffers, reducing power consumption, while the use of a current reference resistor close to the WM8980 ensures that the signal swing seen at the output of the buffer will be the same as that at the connection to the receiving equipment (e.g. a TV), providing excellent signal reproduction. Current mode output also provides inherent short circuit protection at the signal output. w PP, Rev 3.8, May 2012 72 WM8980 Pre-Production Figure 41 Video Buffer with 0dB Gain Figure 42 Video Buffer with 6dB Gain The outputs VBREF and VBOUT are current mirrored transistors with a 5:1 ratio, so that: iVBOUT = 5 x iVBREF. A reference resistor (187R in above examples) is used for feedback on the video buffer amplifier via the VBREF pin. The output current from VBOUT will be split between the source termination and load termination (75R each in above examples). Overall voltage gain (i.e. VBIN to TV input) is calculated as follows: VBGAIN LOADED GAIN FORMULA LOADED GAIN UNLOADED GAIN (R40[1]) (SOURCE AND LOAD BOTH TERMINATED WITH 75R) (VREF=187R; RSOURCE=75R; RLOAD=75R) (VREF=187R; RSOURCE=75R; RLOAD=0) 0 5 x (RLOAD || RSOURCE) / RVBREF 0dB +6dB 1 10 x (RLOAD || RSOURCE) / RVBREF +6dB +12dB See applications note WAN-0166 for further information. w PP, Rev 3.8, May 2012 73 WM8980 Pre-Production DIGITAL AUDIO INTERFACES The audio interface has four pins: ADCDAT: ADC data output DACDAT: DAC data input LRC: Data Left/Right alignment clock BCLK: Bit clock, for synchronisation The clock signals BCLK, and LRC can be outputs when the WM8980 operates as a master, or inputs when it is a slave (see Master and Slave Mode Operation, below). Five different audio data formats are supported: Left justified Right justified IS DSP mode A DSP mode B 2 All of these modes are MSB first. They are described in Audio Data Formats, below. Refer to the Electrical Characteristic section for timing information. MASTER AND SLAVE MODE OPERATION The WM8980 audio interface may be configured as either master or slave. As a master interface device the WM8980 generates BCLK and LRC and thus controls sequencing of the data transfer on ADCDAT and DACDAT. To set the device to master mode register bit MS should be set high. In slave mode (MS=0), the WM8980 responds with data to clocks it receives over the digital audio interfaces. AUDIO DATA FORMATS In Left Justified mode, the MSB is available on the first rising edge of BCLK following an LRC transition. The other bits up to the LSB are then transmitted in order. Depending on word length, BCLK frequency and sample rate, there may be unused BCLK cycles before each LRC transition. Figure 43 Left Justified Audio Interface (assuming n-bit word length) w PP, Rev 3.8, May 2012 74 WM8980 Pre-Production In Right Justified mode, the LSB is available on the last rising edge of BCLK before a LRC transition. All other bits are transmitted before (MSB first). Depending on word length, BCLK frequency and sample rate, there may be unused BCLK cycles after each LRC transition. Figure 44 Right Justified Audio Interface (assuming n-bit word length) 2 In I S mode, the MSB is available on the second rising edge of BCLK following a LRC transition. The other bits up to the LSB are then transmitted in order. Depending on word length, BCLK frequency and sample rate, there may be unused BCLK cycles between the LSB of one sample and the MSB of the next. 2 Figure 45 I S Audio Interface (assuming n-bit word length) w PP, Rev 3.8, May 2012 75 WM8980 Pre-Production st nd In DSP/PCM mode, the left channel MSB is available on either the 1 (mode B) or 2 (mode A) rising edge of BCLK (selectable by LRP) following a rising edge of LRC. Right channel data immediately follows left channel data. Depending on word length, BCLK frequency and sample rate, there may be unused BCLK cycles between the LSB of the right channel data and the next sample. Figure 46 DSP/PCM Mode Audio Interface (mode A, LRP=0) Figure 47 DSP/PCM Mode Audio Interface (mode B, LRP=1) w PP, Rev 3.8, May 2012 76 WM8980 Pre-Production REGISTER ADDRESS R4 BIT 0 LABEL MONO DEFAULT 0 Audio Interface Control DESCRIPTION Selects between stereo and mono device operation: 0=Stereo device operation 1=Mono device operation. Data appears in ‘left’ phase of LRC 1 ADCLRSWAP 0 Controls whether ADC data appears in ‘right’ or ‘left’ phases of LRC clock: 0=ADC data appear in ‘left’ phase of LRC 1=ADC data appears in ‘right’ phase of LRC 2 DACLRSWAP 0 Controls whether DAC data appears in ‘right’ or ‘left’ phases of LRC clock: 0=DAC data appear in ‘left’ phase of LRC 1=DAC data appears in ‘right’ phase of LRC 4:3 FMT 10 Audio interface Data Format Select: 00=Right Justified 01=Left Justified 2 10=I S format 11= DSP/PCM mode 6:5 WL 10 Word length 00=16 bits 01=20 bits 10=24 bits 11=32 bits (see note) 7 LRP right, left and i2s modes – LRCLK polarity 1 = invert LRCLK polarity 0 = normal LRCLK polarity DSP Mode – mode A/B select n 1 = MSB is available o 1st BCLK rising edge after LRC rising edge (mode B) n 0 = MSB is available o 2nd BCLK rising edge after LRC rising edge (mode A) 8 BCP BCLK polarity 0=normal 1=inverted Table 55 Audio Interface Control ADCLRSWAP bit controls whether the ADC data appears in the right or left phase of the LRC clock as defined for each audio format. Similarly, DACLRSWAP can be used to swap the left DAC data from the left phase to the right phase of the LRC clock and the right DAC data from the right phase to the left phase of the LRC clock. Note: Right Justified Mode will only operate with a maximum of 24 bits. If 32-bit mode is selected, the device will operate in 24-bit mode. AUDIO INTERFACE CONTROL The register bits controlling audio format, word length and master / slave mode are summarised below. The audio interfaces can be controlled individually. Register bit MS selects audio interface operation in master or slave mode. In Master mode BCLK, and LRC are outputs. The frequency of BCLK in master mode are controlled with BCLKDIV. These are divided down versions of master clock. This may result in short BCLK pulses at the end of a LRC if there is a non-integer ratio of BCLKs to LRC clocks. w PP, Rev 3.8, May 2012 77 WM8980 Pre-Production REGISTER ADDRESS R6 BIT 0 LABEL MS DEFAULT 0 Clock Generation Control DESCRIPTION Sets the chip to be master over LRC and BCLK 0=BCLK and LRC clock are inputs 1=BCLK and LRC clock are outputs generated by the WM8980 (MASTER) 4:2 BCLKDIV 000 Configures the BCLK output frequency, for use when the chip is master over BCLK. 000=divide by 1 (BCLK=SYSCLK) 001=divide by 2 (BCLK=SYSCLK/2) 010=divide by 4 011=divide by 8 100=divide by 16 101=divide by 32 110=reserved 111=reserved 7:5 MCLKDIV 010 Sets the scaling for either the MCLK or PLL clock output (under control of CLKSEL) 000=divide by 1 001=divide by 1.5 010=divide by 2 011=divide by 3 100=divide by 4 101=divide by 6 110=divide by 8 111=divide by 12 8 CLKSEL 1 Controls the source of the clock for all internal operation: 0=MCLK 1=PLL output Table 56 Clock Control The CLKSEL bit selects the internal source of the Master clock from the PLL (CLKSEL=1) or from MCLK (CLKSEL=0). When the internal clock is switched from one source to another using the CLKSEL bit, the clock originally selected must generate at least one falling edge after CLKSEL has changed for the switching of clocks to be successful. EXAMPLE: If the PLL is the current source of the internal clock (CLKSEL=1) and it is required to switch to the MCLK, change CLKSEL to select MCLK (CLKSEL=0) and then disable PLL (PLLEN=0). w PP, Rev 3.8, May 2012 78 WM8980 Pre-Production AUDIO SAMPLE RATES The WM8980 sample rates for the ADCs and the DACs are set using the SR register bits. The cutoffs for the digital filters and the ALC attack/decay times stated are determined using these values and assume a 256fs master clock rate. If a sample rate that is not explicitly supported by the SR register settings is required then the closest SR value to that sample rate should be chosen, the filter characteristics and the ALC attack, decay and hold times will scale appropriately. REGISTER ADDRESS R7 BIT LABEL 3:1 SR DEFAULT 000 Additional Control DESCRIPTION Approximate sample rate (configures the coefficients for the internal digital filters): 000=48kHz 001=32kHz 010=24kHz 011=16kHz 100=12kHz 101=8kHz 110-111=reserved Table 57 Sample Rate Control MASTER CLOCK AND PHASE LOCKED LOOP (PLL) The WM8980 has an on-chip phase-locked loop (PLL) circuit that can be used to: Generate master clocks for the WM8980 audio functions from another external clock, e.g. in telecoms applications. Generate and output (on pin CSB/GPIO1 and/or GPI04) a clock for another part of the system that is derived from an existing audio master clock. Figure 48 shows the PLL and internal clockingٛ arrangement on the WM8980. The PLL can be enabled or disabled by the PLLEN register bit. Note: In order to minimise current consumption, the PLL is disabled when the VMIDSEL[1:0] bits are set to 00b. VMIDSEL[1:0] must be set to a value other than 00b to enable the PLL. REGISTER ADDRESS R1 BIT 5 Power management 1 LABEL PLLEN DEFAULT 0 DESCRIPTION PLL enable 0=PLL off 1=PLL on Table 58 PLLEN Control Bit w PP, Rev 3.8, May 2012 79 WM8980 Pre-Production Figure 48 PLL and Clock Select Circuit The PLL frequency ratio R = f2/f1 (see Figure 48) can be set using the register bits PLLK and PLLN: PLLN = int R 24 PLLK = int (2 (R-PLLN)) Note: The PLL is designed to operate with best performance (shortest lock time and optimum stability) when f2 is between 90 and 100MHz and PLL_N is 8. However, acceptable PLL_N values lie in the range 5 ≤ PLL_N ≤ 13. Do not use values outwith this range and it is recommended that the chosen value of PLL_N is as close to 8 as possible for optimum performance. EXAMPLE: MCLK=12MHz, required clock = 12.288MHz. R should be chosen to ensure 5 < PLLN < 13. There is a fixed divide by 4 in the PLL and a selectable divide by N after the PLL which should be set to divide by 2 to meet this requirement. Enabling the divide by 2 sets the required f2 = 4 x 2 x 12.288MHz = 98.304MHz. R = 98.304 / 12 = 8.192 PLLN = int R = 8 24 k = int ( 2 x (8.192 – 8)) = 3221225 = 3126E9h REGISTER ADDRESS R36 BIT LABEL DEFAULT 4 PLLPRESCALE 0 Divide MCLK by 2 before input to PLL 3:0 PLLN[3:0] 1000 Integer (N) part of PLL input/output frequency ratio. Use values greater than 5 and less than 13. 5:0 PLLK [23:18] 0Ch Fractional (K) part of PLL1 input/output frequency ratio (treat as one 24-digit binary number). 8:0 PLLK [17:9] 093h 8:0 PLLK [8:0] 0E9h PLL N value R37 PLL K value 1 R38 DESCRIPTION PLL K Value 2 R39 PLL K Value 3 Table 59 PLL Frequency Ratio Control w PP, Rev 3.8, May 2012 80 WM8980 Pre-Production The PLL performs best when f2 is around 90MHz. Its stability peaks at N=8. Some example settings are shown in Table 60. DESIRED OUTPUT (MHZ) F2 PRESCALE POSTSCALE (MHZ) DIVIDE DIVIDE 12 11.29 90.3168 1 2 12 12.288 98.304 1 2 13 11.29 90.3168 1 MCLK (MHZ) (F1) R N K (HEX) (HEX) 7.5264 7 86C226 8.192 8 3126E8 2 6.947446 6 F28BD4 13 12.288 98.304 1 2 7.561846 7 8FD525 14.4 11.29 90.3168 1 2 6.272 6 45A1CA 14.4 12.288 98.304 1 2 6.826667 6 D3A06E 19.2 11.29 90.3168 2 2 9.408 9 6872AF 19.2 12.288 98.304 2 2 10.24 A 3D70A3 19.68 11.29 90.3168 2 2 9.178537 9 2DB492 19.68 12.288 98.304 2 2 9.990243 9 FD809F 19.8 11.29 90.3168 2 2 9.122909 9 1F76F7 19.8 12.288 98.304 2 2 9.929697 9 EE009E 24 11.29 90.3168 2 2 7.5264 7 86C226 24 12.288 98.304 2 2 8.192 8 3126E8 26 11.29 90.3168 2 2 6.947446 6 F28BD4 26 12.288 98.304 2 2 7.561846 7 8FD525 27 11.29 90.3168 2 2 6.690133 6 BOAC93 27 12.288 98.304 2 2 7.281778 7 482296 Table 60 PLL Frequency Examples LOOPBACK Setting the LOOPBACK register bit enables digital loopback. When this bit is set the output data from the ADC audio interface is fed directly into the DAC data input. COMPANDING The WM8980 supports A-law and -law and companding and linear mode on both transmit (ADC) and receive (DAC) sides. Companding can be enabled on the DAC or ADC audio interfaces by writing the appropriate value to the DAC_COMP or ADC_COMP register bits respectively. w PP, Rev 3.8, May 2012 81 WM8980 Pre-Production REGISTER ADDRESS R5 BIT 0 LABEL DEFAULT LOOPBACK 0 Companding Control DESCRIPTION Digital loopback function 0=No loopback 1=Loopback enabled, ADC data output is fed directly into DAC data input. 2:1 ADC_COMP 0 ADC companding 00=off (linear mode) 01=reserved 10=µ-law 11=A-law 4:3 DAC_COMP 0 DAC companding 00=off (linear mode) 01=reserved 10=µ-law 11=A-law 5 WL8 0 Companding Control 8-bit mode 0=off 1=device operates in 8-bit mode Table 61 Companding Control Companding involves using a piecewise linear approximation of the following equations (as set out by ITU-T G.711 standard) for data compression: -law (where =255 for the U.S. and Japan): F(x) = ln( 1 + |x|) / ln( 1 + ) -1 ≤ x ≤ 1 A-law (where A=87.6 for Europe): F(x) = A|x| / ( 1 + lnA) for x ≤ 1/A F(x) = ( 1 + lnA|x|) / (1 + lnA) for 1/A ≤ x ≤ 1 The companded data is also inverted as recommended by the G.711 standard (all 8 bits are inverted for -law, all even data bits are inverted for A-law). The data will be transmitted as the first 8 MSB’s of data. Companding converts 13 bits (-law) or 12 bits (A-law) to 8 bits using non-linear quantization. The input data range is separated into 8 levels, allowing low amplitude signals better precision than that of high amplitude signals. This is to exploit the operation of the human auditory system, where louder sounds do not require as much resolution as quieter sounds. The companded signal is an 8-bit word containing sign (1-bit), exponent (3-bits) and mantissa (4-bits). Setting the WL8 register bit allows the device to operate with 8-bit data. In this mode it is possible to use 8 BCLK’s per LRC frame. When using DSP mode B, this allows 8-bit data words to be output consecutively every 8 BCLK’s and can be used with 8-bit data words using the A-law and u-law companding functions. BIT7 BIT[6:4] BIT[3:0] SIGN EXPONENT MANTISSA Table 62 8-bit Companded Word Composition w PP, Rev 3.8, May 2012 82 WM8980 Pre-Production u-law Companding 1 120 0.9 Companded Output 0.7 80 0.6 0.5 60 0.4 40 0.3 Normalised Output 0.8 100 0.2 20 0.1 0 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 Normalised Input Figure 49 u-Law Companding A-law Companding 1 120 0.9 Companded Output 0.7 80 0.6 0.5 60 0.4 40 0.3 Normalised Output 0.8 100 0.2 20 0.1 0 0 0 0.2 0.4 0.6 0.8 1 Normalised Input Figure 50 A-Law Companding GENERAL PURPOSE INPUT/OUTPUT The WM8980 has three dual purpose input/output pins and one dedicated GPIO. CSB/GPIO1: CSB / GPIO pin L2/GPIO2: Left channel line input / headphone detection input R2/GPIO3: Right channel line input / headphone detection input GPIO4: Dedicated GPIO The GPIO2 and GPIO3 functions are provided for use as jack detection inputs. The GPIO1 and GPIO4 functions are provided for use as jack detection inputs or general purpose outputs. The default configuration for the CSB/GPIO1 and GPIO4 pins are to be inputs. w PP, Rev 3.8, May 2012 83 WM8980 Pre-Production When setup as an input, the CSB/GPIO1 pin can either be used as CSB or for jack detection, depending on how the MODE pin is set. If setup as an input, the GPIO4 pin can also be used for jack detection. Table 63 illustrates the functionality of the GPIO1 and GPIO4 pins when used as general purpose outputs. REGISTER ADDRESS R8 BIT 2:0 LABEL GPIO1SEL DEFAULT 000 GPIO DESCRIPTION CSB/GPIO1 pin function select: 000= input (CSB/jack detection: depending on MODE setting) Control 001= reserved 010=Temp ok 011=Amute active 100=PLL clk o/p 101=PLL lock 110=logic 0 111=logic 1 3 GPIO1POL 0 GPIO1 Polarity invert 0=Non inverted 1=Inverted 5:4 OPCLKDIV 00 PLL Output clock division ratio 00=divide by 1 01=divide by 2 10=divide by 3 11=divide by 4 R9 2:0 GPIO4SEL 000 GPIO4 pin function select: GPIO 000= input jack detection Control 001= reserved 010=Temp ok 011=Amute active 100=PLL clk o/p 101=PLL lock 110=logic 1 111=logic 0 3 GPIO4POL 0 GPIO4 Polarity invert 0=Non inverted 1=Inverted Table 63 CSB/GPIO Control Note: If MODE is set to 3 wire mode, CSB/GPIO1 shall be used as CSB input irrespective of the GPIO1SEL[2:] bits. Note that SLOWCLKEN must be enabled when using the Jack Detect function. For further details of the Jack detect operation see the OUTPUT SWITCHING section. OUTPUT SWITCHING (JACK DETECT) When the device is configured with a 2-wire interface the CSB/GPIO1 pin can be used as a switch control input to automatically disable one set of outputs and enable another. The L2/GPIO2, R2/GPIO3 and GPIO4 pins can also be used for this purpose. For example, when a headphone is plugged into a jack socket then it may be desirable to disable the speaker (e.g. when one of the GPIO pins is connected to a mechanical switch in the headphone socket to detect plug-in). The GPIO pins have an internal de-bounce circuit when in this mode in order to prevent the output enables from toggling multiple times due to input glitches. This de-bounce circuit is clocked from a 21 slow clock with period 2 x MCLK. Note that SLOWCLKEN must be enabled when using the Jack Detect function. w PP, Rev 3.8, May 2012 84 WM8980 Pre-Production Note that the GPIOPOL bits are not relevant for jack detection, it is the signal detected at the pin which is used. The switching on/off of the outputs is fully configurable by the user. Each output, OUT1, OUT2, OUT3 and OUT4 has 2 associated enables. OUT1_EN_0, OUT2_EN_0, OUT3_EN_0 and OUT4_EN_0 are the output enable signal which are used if the selected jack detection pin is at logic 0 (after debounce). OUT1_EN_1, OUT2_EN_1, OUT3_EN_1 and OUT4_EN_1 are the output enable signals which are used if the selected jack detection pin is at logic 1 (after de-bounce). Similar to the output enables, VMID, which can be driven out of OUT3 can be configured to be on/off depending on the jack detection input polarity using the VMID_EN_0 and VMID_EN_1 bits. The jack detection enables work as follows: All OUT_EN signals have an AND function performed with their normal enable signals (in Table 50). When an output is normally enabled at per Table 50, the selected jack detection enable (controlled by selected jack detection pin polarity) is set 0, it will turn the output off. If the normal enable signal is already OFF (0), the jack detection signal will have no effect due on the AND function. During jack detection if the user desires an output to be un-changed whether the jack is in or not, both the JD_EN settings i.e. JD_EN0 and JD_EN1, should be set to 0000. The VMID_EN signal has an OR function performed with the normal VMID driver enable. If the VMID_EN signal is to have no effect to normal functionality when jack detection is enabled, it should set to 0 for all JD_EN0 or JD_EN1 settings. If jack detection is not enabled (JD_EN=0), the output enables default to all 1’s, allowing the outputs to be controlled as normal via the normal output enables found in Table 50. Similarly the VMID_EN signal defaults to 0 allowing the VMID driver to be controlled via the normal enable bit. REGISTER ADDRESS R9 BIT 5:4 LABEL JD_SEL DEFAULT 00 GPIO Control DESCRIPTION Pin selected as jack detection input 00 = GPIO1 01 = GPIO2 10 = GPIO3 11 = GPIO4 6 JD_EN 0 Jack Detection Enable 0=disabled 1=enabled 8:7 JD_VMID 00 3:0 JD_EN0 0 [7] VMID_EN_0 [8] VMID_EN_1 R13 GPW Control Output enabled when selected jack detection input is logic 0. [0]= OUT1_EN_0 [1]= OUT2_EN_0 [2]= OUT3_EN_0 [3]= OUT4_EN_0 7:4 JD_EN1 0 Output enabled when selected jack detection input is logic 1 [4]= OUT1_EN_1 [5]= OUT2_EN_1 [6]= OUT3_EN_1 [7]= OUT4_EN_1 Table 64 Jack Detect Register Control Bits w PP, Rev 3.8, May 2012 85 WM8980 Pre-Production CONTROL INTERFACE SELECTION OF CONTROL MODE AND 2-WIRE MODE ADDRESS The control interface can operate as either a 3-wire or 2-wire MPU interface. The MODE pin determines the 2 or 3 wire mode as shown in Table 65. The WM8980 is controlled by writing to registers through a serial control interface. A control word consists of 16 bits. The first 7 bits (B15 to B9) are address bits that select which control register is accessed. The remaining 9 bits (B8 to B0) are register bits, corresponding to the 9 bits in each control register. MODE INTERFACE FORMAT Low 2 wire High 3 wire Table 65 Control Interface Mode Selection 3-WIRE SERIAL CONTROL MODE In 3-wire mode, every rising edge of SCLK clocks in one data bit from the SDIN pin. A rising edge on CSB/GPIO1 pin latches in a complete control word consisting of the last 16 bits. Figure 51 3-Wire Serial Control Interface 2-WIRE SERIAL CONTROL MODE The WM8980 supports software control via a 2-wire serial bus. Many devices can be controlled by the same bus, and each device has a unique 7-bit device address (this is not the same as the 7-bit address of each register in the WM8980). The WM8980 operates as a slave 2-wire device only. The controller indicates the start of data transfer with a high to low transition on SDIN while SCLK remains high. This indicates that a device address and data will follow. All devices on the 2-wire bus respond to the start condition and shift in the next eight bits on SDIN (7-bit address + Read/Write bit, MSB first). If the device address received matches the address of the WM8980, then the WM8980 responds by pulling SDIN low on the next clock pulse (ACK). If the address is not recognised or the R/W bit is ‘1’ when operating in write only mode, the WM8980 returns to the idle condition and wait for a new start condition and valid address. During a write, once the WM8980 has acknowledged a correct address, the controller sends the first byte of control data (B15 to B8, i.e. the WM8980 register address plus the first bit of register data). The WM8980 then acknowledges the first data byte by pulling SDIN low for one clock pulse. The controller then sends the second byte of control data (B7 to B0, i.e. the remaining 8 bits of register data), and the WM8980 acknowledges again by pulling SDIN low. Transfers are complete when there is a low to high transition on SDIN while SCLK is high. After a complete sequence the WM8980 returns to the idle state and waits for another start condition. If a start or stop condition is detected out of sequence at any point during data transfer (i.e. SDIN changes while SCLK is high), the device jumps to the idle condition. DEVICE ADDRESS (7 BITS) SDIN RD / WR BIT ACK (LOW) CONTROL BYTE 1 (BITS 15 TO 8) ACK (LOW) CONTROL BYTE 1 (BITS 7 TO 0) ACK (LOW) SCLK START register address and 1st register data bit remaining 8 bits of register data STOP Figure 52 2-Wire Serial Control Interface w PP, Rev 3.8, May 2012 86 WM8980 Pre-Production In 2-wire mode the WM8980 has a fixed device address, 0011010. RESETTING THE CHIP The WM8980 can be reset by performing a write of any value to the software reset register (address 0 hex). This will cause all register values to be reset to their default values. In addition to this there is a Power-On Reset (POR) circuit which ensures that the registers are set to default when the device is powered up. POWER SUPPLIES The WM8980 can use up to five separate power supplies: AVDD and AGND: Analogue supply, powers all analogue functions except the speaker output and mono output drivers. AVDD can range from 2.5V to 3.6V and has the most significant impact on overall power consumption (except for power consumed in the headphone). A large AVDD slightly improves audio quality. SPKVDD and SPKGND: Headphone and Speaker supplies, power the speaker and mono output drivers. SPKVDD can range from 2.5V to 5V. SPKVDD can be tied to AVDD, but it requires separate layout and decoupling capacitors to curb harmonic distortion. With a larger SPKVDD, louder headphone and speaker outputs can be achieved with lower distortion. If SPKVDD is lower than AVDD, the output signal may be clipped. DCVDD: Digital core supply, powers all digital functions except the audio and control interfaces. DCVDD can range from 1.71V to 3.6V, and has no effect on audio quality. The return path for DCVDD is DGND, which is shared with DBVDD. DBVDD can range from 1.71V to 3.6V. DBVDD return path is through DGND. VBVDD and VBGND: Supplies for video buffer circuit. VBVDD can range from 2.5V to 3.6V. It is possible to use the same supply voltage for all four supplies. However, digital and analogue supplies should be routed and decoupled separately on the PCB to keep digital switching noise out of the analogue signal paths. DCVDD should be greater than or equal to 1.9V when using the PLL. RECOMMENDED POWER UP/DOWN SEQUENCE In order to minimise output pop and click noise, it is recommended that the WM8980 device is powered up and down using one of the following sequences: Power-up when NOT using the output 1.5x boost stage: 1. Turn on external power supplies. Wait for supply voltage to settle. 2. Mute all analogue outputs. 3. Set L/RMIXEN = 1 and DACENL/R = 1 in register R3. 4. Set BUFIOEN = 1 and VMIDSEL[1:0] to required value in register R1. Wait for the VMID supply to settle. *Refer notes 1 and 2. 5. Set BIASEN = 1 in register R1. 6. Set L/ROUT1EN = 1 in register R2. 7. Enable other mixers as required. 8. Enable other outputs as required. 9. Set remaining registers. Power-up when using the output 1.5x boost stage: w 1. Turn on external power supplies. Wait for supply voltage to settle. 2. Mute all analogue outputs. PP, Rev 3.8, May 2012 87 WM8980 Pre-Production 3. Enable unused output chosen from L/ROUT2, OUT3 or OUT4. If unused output not available, chose one of these outputs not required at power up. 4. Set BUFDCOPEN = 1 and BUFIOEN = 1 in register R1. 5. Set SPKBOOST = 1 in register R49. 6. Set VMIDSEL[1:0] to required value in register R1. Wait for the VMID supply to settle. *Refer notes 1 and 2. 7. Set L/RMIXEN = 1 and DACENL/R = 1 in register R3. 8. Set BIASEN = 1 in register R1. 9. Set L/ROUT2EN = 1 in register R3. *Note 3. 10. Enable other mixers as required. 11. Enable other outputs as required. 12. Set remaining registers. Power Down (all cases): w 1. Mute all analogue outputs. 2. Disable Power Management Register 1. R1 = 0x00. 3. Disable Power Management Register 2. R2 = 0x00. 4. Disable Power Management Register 3. R3 = 0x00. 5. Remove external power supplies. PP, Rev 3.8, May 2012 88 WM8980 Pre-Production Notes: 1. This step enables the internal device bias buffer and the VMID buffer for unassigned inputs/outputs. This will provide a startup reference voltage for all inputs and outputs. This will cause the inputs and outputs to ramp towards VMID (NOT using output 1.5x boost) or 1.5 x (AVDD/2) (using output 1.5x boost) in a way that is controlled and predictable (see note 2). 2. Choose the value of the VMIDSEL bits based on the startup time (VMIDSEL=10 for slowest startup, VMIDSEL=11 for fastest startup). Startup time is defined by the value of the VMIDSEL bits (the reference impedance) and the external decoupling capacitor on VMID. 3. Setting DACEN to off while operating in x1.5 boost mode will cause the VMID voltage to drop to AVDD/2 midrail level and cause an output pop. In addition to the power on sequence, it is recommended that the zero cross functions are used when changing the volume in the PGAs to avoid any audible pops or clicks. Vpor_on Vpora Vpor_off Power Supply DGND POR Device Ready No Power POR Undefined Internal POR active POR DNC I2S Clocks DNC tadcint ADC Internal State Power down Init tadcint Normal Operation PD Init Normal Operation tmidrail_on tmidrail_off (Note 1) Analogue Inputs Power down (Note 2) AVDD/2 GD GD GD GD ADCDAT pin (Note 3) ADCEN bit ADC enabled ADC off INPPGAEN bit VMIDSEL/ BIASEN bits ADC enabled INPPGA enabled (Note 4) VMID enabled Figure 53 ADC Power Up and Down Sequence (not to scale) SYMBOL MIN TYPICAL MAX UNIT tmidrail_on 500 tmidrail_off >10 ms s tadcint 2/fs n/fs ADC Group Delay 29/fs n/fs Table 66 Typical POR Operation (typical values, not tested) w PP, Rev 3.8, May 2012 89 WM8980 Pre-Production Notes: 1. The analogue input pin charge time, tmidrail_on, is determined by the VMID pin charge time. This time is dependent upon the value of VMID decoupling capacitor and VMID pin input resistance and AVDD power supply rise time. 2. The analogue input pin discharge time, tmidrail_off, is determined by the analogue input coupling capacitor discharge time. The time, tmidrail_off, is measured using a 1μF capacitor on the analogue input but will vary dependent upon the value of input coupling capacitor. 3. While the ADC is enabled there will be LSB data bit activity on the ADCDAT pin due to system noise but no significant digital output will be present. 4. The VMIDSEL and BIASEN bits must be set to enable analogue input midrail voltage and for normal ADC operation. 5. ADCDAT data output delay from power –p - with power supplies starting from –V - is determined primarily by the VMID charge time. ADC initialisation and power management bits may be set immediately after POR is released; VMID charge time will be significantly longer and will dictate when the device is stabilised for analogue input. 6. ADCDAT data output delay at power up from device standby (power supplies already applied) is determined by ADC initialisation time, 2/fs. Figure 54 DAC Power Up and Down Sequence (not to scale) w PP, Rev 3.8, May 2012 90 WM8980 Pre-Production SYMBOL MIN TYPICAL MAX UNIT tline_midrail_on 500 ms tline_midrail_off 1 s ms thp_midrail_on 500 thp__midrail_off 6 s tdacint 2/fs n/fs DAC Group Delay 29/fs n/fs Table 67 Typical POR Operation (typical values, not tested) Notes: w 1. The lineout charge time, tline_midrail_on, is mainly determined by the VMID pin charge time. This time is dependent upon the value of VMID decoupling capacitor and VMID pin input resistance and AVDD power supply rise time. The values above were measured using a 4.7μF capacitor. 2. It is not advisable to allow DACDAT data input during initialisation of the DAC. If the DAC data value is not zero at point of initialisation, then this is likely to cause a pop noise on the analogue outputs. The same is also true if the DACDAT is removed at a non-zero value, and no mute function has been applied to the signal beforehand. 3. The lineout discharge time, tline_midrail_off, is dependent upon the value of the lineout coupling capacitor and the leakage resistance path to ground. The values above were measured using a 10μF output capacitor. 4. The headphone charge time, thp_midrail_on, is dependent upon the value of VMID decoupling capacitor and VMID pin input resistance and AVDD power supply rise time. The values above were measured using a 4.7μF VMID decoupling capacitor. 5. The headphone discharge time, thp_midrail_off, is dependent upon the value of the headphone coupling capacitor and the leakage resistance path to ground. The values above were measured using a 100μF capacitor. 6. The vmidsel and biasen bits must be set to enable analogue output midrail voltage and for normal dac operation. PP, Rev 3.8, May 2012 91 WM8980 Pre-Production POWER MANAGEMENT SAVING POWER BY REDUCING OVERSAMPLING RATE The default mode of operation of the ADC and DAC digital filters is in 64x oversampling mode. Under the control of ADCOSR and DACOSR the oversampling rate may be doubled. 64x oversampling results in a slight decrease in noise performance compared to 128x but lowers the power consumption of the device. REGISTER ADDRESS R10 BIT LABEL 3 DEFAULT DACOSR128 0 DAC control DESCRIPTION DAC oversample rate select 0 = 64x (lowest power) 1 = 128x (best SNR) R14 3 ADCOSR128 0 ADC control ADC oversample rate select 0 = 64x (lowest power) 1 = 128x (best SNR) Table 68 ADC and DAC Oversampling Rate Selection VMID The analogue circuitry will not work when VMID is disabled (VMIDSEL[1:0] = 00b). The impedance of the VMID resistor string, together with the decoupling capacitor on the VMID pin will determine the startup time of the VMID circuit. REGISTER ADDRESS R1 BIT 1:0 LABEL DEFAULT VMIDSEL 00 Power management 1 DESCRIPTION Reference string impedance to VMID pin (determines startup time): 00=off (open circuit) 01=75kΩ 10=300kΩ 11=5kΩ (for fastest startup) Table 69 VMID Impedance Control BIASEN The analogue amplifiers will not operate unless BIASEN is enabled. REGISTER ADDRESS R1 BIT 3 LABEL BIASEN Power management 1 DEFAULT 0 DESCRIPTION Analogue amplifier bias control 0=disabled 1=enabled Table 70 Analogue Bias Control w PP, Rev 3.8, May 2012 92 WM8980 Pre-Production REGISTER MAP ADDR B[15:9] REGISTER NAME B8 B7 B6 B5 B4 B3 B2 B1 B0 VAL DEC HEX (HEX) 0 00 Software Reset 1 01 Power manage’t 1 2 02 Power manage’t 2 Software reset BUFDCOP OUT4MIX OUT3MIX EN EN EN ROUT1EN LOUT1EN SLEEP PLLEN MICBEN BIASEN BUFIOEN BOOST BOOST INPPGA INPPGA ENR ENL ENR ENL RMIXEN 3 03 Power manage’t 3 OUT4EN OUT3EN LOUT2EN ROUT2EN 4 04 Audio Interface BCP LRP WL 5 05 Companding ctrl 0 0 6 06 Clock Gen ctrl CLKSEL 7 07 Additional ctrl 0 8 08 GPIO Stuff 0 9 09 Jack detect control 10 0A DAC Control 11 0B Left DAC digital Vol DACVU VBUFEN DACVOLL 12 0C Right DAC dig’l Vol DACVU DACVOLR FMT 0 WL8 MCLKDIV 0 0 0 0 0 14 0E LMIXEN DACENR DACENL 000 DAC ADC MONO 050 LRSWAP LRSWAP ADC_COMP SR 000 MS 140 SLOWCLKE N 000 OPCLKDIV GPIO1POL GPIO1SEL[2:0] JD_SEL GPIO4POL GPIO4SEL[2:0] 0 0 DACOSR AMUTE HPFAPP 000 000 DACPOLR DACPOLL 000 128 0FF 0FF JD_EN1 HPFEN LOOPBACK 0 0 Jack Detect Control ADC Control 000 JD_EN SOFT 000 ADCENL BCLKDIV 0 0 JD_VMID VMIDSEL ADCENR DAC_COMP MUTE 13 0D DEF’T JD_EN0 HPFCUT ADCOSR 0 000 ADCRPOL ADCLPOL 100 128 15 0F Left ADC Digital Vol ADCVU ADCVOLL 0FF 16 10 Right ADC Digital Vol ADCVU ADCVOLR 0FF 18 12 EQ1 – low shelf EQ3DMODE 0 EQ1C EQ1G 12C 19 13 EQ2 – peak 1 EQ2BW 0 EQ2C EQ2G 02C 20 14 EQ3 – peak 2 EQ3BW 0 EQ3C EQ3G 02C 21 15 EQ4 – peak 3 EQ4BW 0 EQ4C EQ4G 02C 22 16 EQ5 – high shelf 0 0 EQ5C EQ5G 02C 24 18 DAC Limiter 1 LIMEN 25 19 DAC Limiter 2 0 0 27 1B Notch Filter 1 NFU NFEN NFA0[13:7] 000 28 1C Notch Filter 2 NFU 0 NFA0[6:0] 000 29 1D Notch Filter 3 NFU 0 NFA1[13:7] 000 30 1E Notch Filter 4 NFU 0 NFA1[6:0] 32 20 ALC control 1 33 21 ALC control 2 ALCZC 34 22 ALC control 3 ALCMODE 35 23 Noise Gate 0 0 0 0 0 36 24 PLL N 0 0 0 0 PLLPRE LIMDCY LIMLVL ALCSEL 0 LIMATK 032 LIMBOOST 000 000 ALCMAXGAIN ALCMINGAIN ALCHLD ALCDCY 038 ALCLVL 00B ALCATK 032 NGEN NGTH 000 PLLN[3:0] 008 SCALE 37 25 PLL K 1 38 26 PLL K 2 PLLK[17:9] 093 39 27 PLL K 3 PLLK[8:0] 0E9 40 28 Video Buffer 41 29 3D control 0 0 0 0 0 43 2B Beep control 0 0 0 MUTER PGA2INV INVROUT2 w 0 0 0 0 0 0 PLLK[23:18] 0 QBOOST 0 00C 0 VBGAIN VBCLAMP EN DEPTH3D BEEPVOL 000 000 BEEPEN 000 PP, Rev 3.8, May 2012 93 WM8980 44 45 46 2C 2D 2E Input ctrl Pre-Production MBVSEL Left INP PGA gain ctrl UPDATE Right INP PGA gain ctrl UPDATE 0 INPPGA INPGA R2_2 RIN2 RIP2 INPPGA INPPGA INPPGA 0 L2_2 LIN2 LIP2 INPPGA INPPGA INPPGA 033 INPPGAZC INPPGA L MUTEL INPPGAVOLL 010 INPPGAZC INPPGA R MUTER INPPGAVOLR 010 47 2F Left ADC Boost ctrl PGABOOSTL 0 L2_2BOOSTVOL 0 AUXL2BOOSTVOL 100 48 30 Right ADC Boost ctrl PGABOOSTR 0 R2_2BOOSTVOL 0 AUXR2BOOSTVOL 100 49 31 Output ctrl 0 0 TSDEN 002 DACL2 DACR2 OUT4 OUT3 SPK RMIX LMIX BOOST BOOST BOOST VROI 50 32 Left mixer ctrl AUXLMIXVOL AUXL2LMIX BYPLMIXVOL BYPL2LMIX DACL2LMIX 001 51 33 Right mixer ctrl AUXRMIXVOL AUXR2RMI X BYPRMIXVOL BYPR2RMIX DACR2RMIX 001 52 34 LOUT1 (HP) volume ctrl HPVU ROUT1 (HP) volume ctrl HPVU LOUT2 (SPK) volume ctrl SPKVU ROUT2 (SPK) volume ctrl SPKVU OUT3 mixer ctrl 0 53 54 55 56 35 36 37 38 LOUT1ZC LOUT1 ROUT1ZC ROUT1 39 039 ROUT1VOL 039 LOUT2VOL 039 ROUT2VOL 039 MUTE LOUT2ZC LOUT2 MUTE ROUT2ZC ROUT2 MUTE 0 OUT3 0 0 OUT4_ BYPL2 LMIX2 LDAC2 2OUT3 OUT3 OUT3 OUT3 LMIX2 LDAC2 BYPR2 RMIX2 RDAC2 OUT4 OUT4 OUT4 OUT4 OUT4 MUTE 57 LOUT1VOL MUTE OUT4 (MONO) mixer ctrl 0 0 OUT4 MUTE HALFSIG 001 001 Table 71 WM8980 Register Map w PP, Rev 3.8, May 2012 94 WM8980 Pre-Production REGISTER BITS BY ADDRESS Notes: 1. Default values of N/A indicate non-latched data bits (e.g. software reset or volume update bits). 2. Register bits marked as "Reserved" should not be changed from the default. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION REFER TO 0 (00h) [8:0] RESET N/A Software reset Resetting the Chip 1 (01h) 8 BUFDCOPEN 0 Dedicated buffer for DC level shifting output stages when in 1.5x gain boost configuration. Analogue Outputs 0=Buffer disabled 1=Buffer enabled (required for 1.5x gain boost) 7 OUT4MIXEN 0 OUT4 mixer enable 0=disabled Power Management 1=enabled 6 OUT3MIXEN 0 OUT3 mixer enable 0=disabled Power Management 1=enabled 5 PLLEN 0 PLL enable 0=PLL off 1=PLL on 4 MICBEN 0 Microphone Bias Enable 0 = OFF (high impedance output) Master Clock and Phase Locked Loop (PLL) Input Signal Path 1 = ON 3 BIASEN 0 Analogue amplifier bias control 0=disabled Power Management 1=enabled 2 BUFIOEN 0 Unused input/output tie off buffer enable 0=disabled Power Management 1=enabled 1:0 VMIDSEL 00 Reference string impedance to VMID pin 00=off (open circuit) Power Management 01=75kΩ 10=300kΩ 11=5kΩ 2 (02h) 8 ROUT1EN 0 ROUT1 output enable 0=disabled Power Management 1=enabled 7 LOUT1EN 0 LOUT1 output enable 0=disabled Power Management 1=enabled 6 SLEEP 0 0 = normal device operation 1 = residual current reduced in device standby mode 5 BOOSTENR 0 Right channel Input BOOST enable 0 = Boost stage OFF Power Management Power Management 1 = Boost stage ON 4 BOOSTENL 0 Left channel Input BOOST enable 0 = Boost stage OFF Power Management 1 = Boost stage ON 3 INPPGAENR 0 Right channel input PGA enable 0 = disabled Power Management 1 = enabled w PP, Rev 3.8, May 2012 95 WM8980 Pre-Production REGISTER ADDRESS BIT 2 LABEL INPPGAENL DEFAULT 0 DESCRIPTION Left channel input PGA enable 0 = disabled REFER TO Power Management 1 = enabled 1 ADCENR 0 Enable ADC right channel: 0 = ADC disabled 1 = ADC enabled 0 ADCENL 0 Enable ADC left channel: 0 = ADC disabled 1 = ADC enabled 3 (03h) 8 OUT4EN 0 OUT4 enable 0 = disabled Analogue to Digital Converter (ADC) Analogue to Digital Converter (ADC) Power Management 1 = enabled 7 OUT3EN 0 OUT3 enable 0 = disabled Power Management 1 = enabled 6 LOUT2EN 0 LOUT2 enable 0 = disabled Power Management 1 = enabled 5 ROUT2EN 0 ROUT2 enable 0 = disabled Power Management 1 = enabled 4 VBUFEN 0 Video buffer enable Video Buffer 0 = disabled 1 = enabled 3 RMIXEN 0 Right output channel mixer enable: 0 = disabled Analogue Outputs 1 = enabled 2 LMIXEN 0 Left output channel mixer enable: 0 = disabled Analogue Outputs 1 = enabled 1 DACENR 0 Right channel DAC enable 0 = DAC disabled Analogue Outputs 1 = DAC enabled 0 DACENL 0 Left channel DAC enable 0 = DAC disabled Analogue Outputs 1 = DAC enabled w PP, Rev 3.8, May 2012 96 WM8980 Pre-Production REGISTER ADDRESS 4 (04h) BIT 8 LABEL BCP DEFAULT 0 DESCRIPTION BCLK polarity 0=normal REFER TO Digital Audio Interfaces 1=inverted 7 LRP 0 right, left and i2s modes – LRCLK polarity 1 = invert LRCLK polarity Digital Audio Interfaces 0 = normal LRCLK polarity DSP Mode – mode A/B select 1 = MSB is available on 1st BCLK rising edge after LRC rising edge (mode B) 0 = MSB is available on 2nd BCLK rising edge after LRC rising edge (mode A) 6:5 WL 10 Word length 00=16 bits Digital Audio Interfaces 01=20 bits 10=24 bits 11=32 bits 4:3 FMT 10 Audio interface Data Format Select: 00=Right Justified Digital Audio Interfaces 01=Left Justified 2 10=I S format 11= DSP/PCM mode 2 DACLRSWAP 0 Controls whether DAC data appears in ‘right’ or ‘left’ phases of LRC clock: Digital Audio Interfaces 0=DAC data appear in ‘left’ phase of LRC 1=DAC data appears in ‘right’ phase of LRC 1 ADCLRSWAP 0 Controls whether ADC data appears in ‘right’ or ‘left’ phases of LRC clock: Digital Audio Interfaces 0=ADC data appear in ‘left’ phase of LRC 1=ADC data appears in ‘right’ phase of LRC 0 MONO 0 Selects between stereo and mono device operation: Digital Audio Interfaces 0=Stereo device operation 1=Mono device operation. Data appears in ‘left’ phase of LRC 5 (05h) 8:6 5 WL8 000 Reserved 0 Companding Control 8-bit mode 0=off Digital Audio Interfaces 1=device operates in 8-bit mode 4:3 DAC_COMP 00 DAC companding 00=off (linear mode) Digital Audio Interfaces 01=reserved 10=µ-law 11=A-law 2:1 ADC_COMP 00 ADC companding 00=off (linear mode) Digital Audio Interfaces 01=reserved 10=µ-law 11=A-law 0 LOOPBACK 0 Digital loopback function 0=No loopback Digital Audio Interfaces 1=Loopback enabled, ADC data output is fed directly into DAC data input. w PP, Rev 3.8, May 2012 97 WM8980 Pre-Production REGISTER ADDRESS 6 (06h) BIT 8 LABEL CLKSEL DEFAULT 1 DESCRIPTION Controls the source of the clock for all internal operation: REFER TO Digital Audio Interfaces 0=MCLK 1=PLL output 7:5 MCLKDIV 010 Sets the scaling for either the MCLK or PLL clock output (under control of CLKSEL) Digital Audio Interfaces 000=divide by 1 001=divide by 1.5 010=divide by 2 011=divide by 3 100=divide by 4 101=divide by 6 110=divide by 8 111=divide by 12 4:2 BCLKDIV 000 Configures the BCLK output frequency, for use when the chip is master over BCLK. Digital Audio Interfaces 000=divide by 1 (BCLK=SYSCLK) 001=divide by 2 (BCLK=SYSCLK/2) 010=divide by 4 011=divide by 8 100=divide by 16 101=divide by 32 110=reserved 111=reserved 1 0 MS 0 Reserved 0 Sets the chip to be master over LRC and BCLK 0=BCLK and LRC clock are inputs Digital Audio Interfaces 1=BCLK and LRC clock are outputs generated by the WM8980 (MASTER) 7 (07h) 8:4 3:1 SR 00000 Reserved 000 Approximate sample rate (configures the coefficients for the internal digital filters): Audio Sample Rates 000=48kHz 001=32kHz 010=24kHz 011=16kHz 100=12kHz 101=8kHz 110-111=reserved 0 SLOWCLKEN 0 Slow clock enable. Used for both the jack insert detect debounce circuit and the zero cross timeout. Analogue Outputs 0 = slow clock disabled 1 = slow clock enabled 8 (08h) 8:6 5:4 000 OPCLKDIV 00 Reserved PLL Output clock division ratio 00=divide by 1 01=divide by 2 10=divide by 3 General Purpose Input/Output (GPIO) 11=divide by 4 3 GPIO1POL 0 GPIO1 Polarity invert 0=Non inverted 1=Inverted w General Purpose Input/Output (GPIO) PP, Rev 3.8, May 2012 98 WM8980 Pre-Production REGISTER ADDRESS BIT 2:0 LABEL GPIO1SEL DEFAULT 000 [2:0] DESCRIPTION CSB/GPIO1 pin function select: 000= input (CSB/jack detection: depending on MODE setting) 001= reserved REFER TO General Purpose Input/Output (GPIO) 010=Temp ok 011=Amute active 100=PLL clk o/p 101=PLL lock 110=logic 1 111=logic 0 9 (09h) 8:7 JD_VMID 00 [7] VMID_EN_0 [8] VMID_EN_1 6 JD_EN 0 Jack Detection Enable 0=disabled 1=enabled 5:4 JD_SEL 00 Pin selected as jack detection input 00 = GPIO1 01 = GPIO2 Output Switching (Jack Detect) Output Switching (Jack Detect) Output Switching (Jack Detect) 10 = GPIO3 11 = GPIO4 3 GPIO4POL 0 GPIO4 Polarity invert 0=Non inverted 1=Inverted 2:0 GPIO4SEL 000 [2:0] GPIO4 pin function select: 000= input jack detection 001= reserved 010=Temp ok General Purpose Input/Output (GPIO) General Purpose Input/Output (GPIO) 011=Amute active 100=PLL clk o/p 101=PLL lock 110=logic 1 111=logic 0 10 (0Ah) 8:7 6 00 SOFTMUTE 0 Reserved Softmute enable: 0=Disabled Output Signal Path 1=Enabled 5:4 3 DACOSR128 00 Reserved 0 DAC oversample rate select 0 = 64x (lowest power) Power Management 1 = 128x (best SNR) 2 AMUTE 0 Automute enable 0 = Amute disabled Output Signal Path 1 = Amute enabled 1 DACPOLR 0 Right DAC output polarity: 0 = non-inverted Output Signal Path 1 = inverted (180 degrees phase shift) 0 DACPOLL 0 Left DAC output polarity: 0 = non-inverted Output Signal Path 1 = inverted (180 degrees phase shift) w PP, Rev 3.8, May 2012 99 WM8980 Pre-Production REGISTER ADDRESS 11 (0Bh) BIT LABEL DEFAULT 8 DACVU N/A 7:0 DACVOLL 11111111 DESCRIPTION REFER TO DAC left and DAC right volume do not update until a 1 is written to DACVU (in reg 11 or 12) Digital to Analogue Converter (DAC) Left DAC Digital Volume Control Digital to Analogue Converter (DAC) 0000 0000 = Digital Mute 0000 0001 = -127dB 0000 0010 = -126.5dB ... 0.5dB steps up to 1111 1111 = 0dB 12 (0Ch) 8 DACVU N/A 7:0 DACVOLR 11111111 DAC left and DAC right volume do not update until a 1 is written to DACVU (in reg 11 or 12) Output Signal Path Right DAC Digital Volume Control Output Signal Path 0000 0000 = Digital Mute 0000 0001 = -127dB 0000 0010 = -126.5dB ... 0.5dB steps up to 1111 1111 = 0dB 13 (0Dh) 8 7:4 JD_EN1 0 Reserved 0000 Output enabled when selected jack detection input is logic 1 [4]= OUT1_EN_1 Output Switching (Jack Detect) [5]= OUT2_EN_1 [6]= OUT3_EN_1 [7]= OUT4_EN_1 3:0 JD_EN0 0000 Output enabled when selected jack detection input is logic 0. [0]= OUT1_EN_0 Output Switching (Jack Detect) [1]= OUT2_EN_0 [2]= OUT3_EN_0 [3]= OUT4_EN_0 14 (0Eh) 8 HPFEN 1 High Pass Filter Enable 0=disabled 1=enabled 7 HPFAPP 0 Select audio mode or application mode st 0=Audio mode (1 order, fc = ~3.7Hz) nd 1=Application mode (2 order, fc = HPFCUT) 6:4 HPFCUT 000 Application mode cut-off frequency See Table 15 for details. 3 ADCOSR 0 128 ADC oversample rate select 0 = 64x (lowest power) Analogue to Digital Converter (ADC) Analogue to Digital Converter (ADC) Analogue to Digital Converter (ADC) Power Management 1 = 128x (best SNR) 2 1 0 ADCRPOL 0 Reserved ADC right channel polarity adjust: 0=normal 1=inverted 0 ADCLPOL 0 ADC left channel polarity adjust: 0=normal 1=inverted w Analogue to Digital Converter (ADC) Analogue to Digital Converter (ADC) PP, Rev 3.8, May 2012 100 WM8980 Pre-Production REGISTER ADDRESS 15 (0Fh) BIT LABEL DEFAULT 8 ADCVU N/A 7:0 ADCVOLL 11111111 DESCRIPTION REFER TO ADC left and ADC right volume do not update until a 1 is written to ADCVU (in reg 16 or 17) Analogue to Digital Converter (ADC) Left ADC Digital Volume Control Analogue to Digital Converter (ADC) 0000 0000 = Digital Mute 0000 0001 = -127dB 0000 0010 = -126.5dB ... 0.5dB steps up to 1111 1111 = 0dB 16 (10h) 8 ADCVU N/A 7:0 ADCVOLR 11111111 ADC left and ADC right volume do not update until a 1 is written to ADCVU (in reg 16 or 17) Analogue to Digital Converter (ADC) Right ADC Digital Volume Control Analogue to Digital Converter (ADC) 0000 0000 = Digital Mute 0000 0001 = -127dB 0000 0010 = -126.5dB ... 0.5dB steps up to 1111 1111 = 0dB 18 (12h) 8 EQ3DMODE 1 0 = Equaliser and 3D Enhancement applied to ADC path Output Signal Path 1 = Equaliser and 3D Enhancement applied to DAC path 7 6:5 0 EQ1C Reserved EQ Band 1 Cut-off Frequency: 00=80Hz Output Signal Path 01=105Hz 10=135Hz 11=175Hz 19 (13h) 4:0 EQ1G 01100 8 EQ2BW 0 EQ Band 1 Gain Control. See Table 37 for details. Output Signal Path EQ Band 2 Bandwidth Control Output Signal Path 0=narrow bandwidth 1=wide bandwidth 7 6:5 EQ2C 0 Reserved Output Signal Path 01 EQ Band 2 Centre Frequency: Output Signal Path 00=230Hz 01=300Hz 10=385Hz 11=500Hz 20 (14h) 4:0 EQ2G 01100 8 EQ3BW 0 EQ Band 2 Gain Control. See Table 37 for details. Output Signal Path EQ Band 3 Bandwidth Control Output Signal Path 0=narrow bandwidth 1=wide bandwidth 7 6:5 0 EQ3C 01 Reserved Output Signal Path EQ Band 3 Centre Frequency: Output Signal Path 00=650Hz 01=850Hz 10=1.1kHz 11=1.4kHz w PP, Rev 3.8, May 2012 101 WM8980 Pre-Production REGISTER ADDRESS 21 (15h) BIT LABEL DEFAULT 4:0 EQ3G 01100 8 EQ4BW 0 DESCRIPTION REFER TO EQ Band 3 Gain Control. See Table 37 for details. Output Signal Path EQ Band 4 Bandwidth Control Output Signal Path 0=narrow bandwidth 1=wide bandwidth 7 6:5 0 EQ4C 01 Reserved Output Signal Path EQ Band 4 Centre Frequency: Output Signal Path 00=1.8kHz 01=2.4kHz 10=3.2kHz 11=4.1kHz 4:0 22 (16h) EQ4G 8:7 6:5 EQ5C 01100 EQ Band 4 Gain Control. See Table 37 for details. Output Signal Path 0 Reserved Output Signal Path EQ Band 5 Cut-off Frequency: Output Signal Path 01 00=5.3kHz 01=6.9kHz 10=9kHz 11=11.7kHz 24 (18h) 4:0 EQ5G 01100 EQ Band 5 Gain Control. See Table 37 for details. Output Signal Path 8 LIMEN 0 Enable the DAC digital limiter: Output Signal Path 0=disabled 1=enabled 7:4 LIMDCY 0011 DAC Limiter Decay time (per 6dB gain change) for 44.1kHz sampling. Note that these will scale with Output Signal Path sample rate: 0000=750us 0001=1.5ms 0010=3ms 0011=6ms 0100=12ms 0101=24ms 0110=48ms 0111=96ms 1000=192ms 1001=384ms 1010=768ms 1011 to 1111=1.536s w PP, Rev 3.8, May 2012 102 WM8980 Pre-Production REGISTER ADDRESS BIT 3:0 LABEL LIMATK DEFAULT 0010 DESCRIPTION REFER TO DAC Limiter Attack time (per 6dB gain change) for 44.1kHz sampling. Note that these will scale with sample rate. Output Signal Path 0000=94us 0001=188s 0010=375us 0011=750us 0100=1.5ms 0101=3ms 0110=6ms 0111=12ms 1000=24ms 1001=48ms 1010=96ms 1011 to 1111=192ms 25 (19h) 8:7 6:4 LIMLVL 00 Reserved 000 Programmable signal threshold level (determines level at which the DAC limiter starts to operate) Output Signal Path 000=-1dB 001=-2dB 010=-3dB 011=-4dB 100=-5dB 101 to 111=-6dB 3:0 LIMBOOST 0000 DAC Limiter volume boost (can be used as a stand alone volume boost when LIMEN=0): Output Signal Path 0000=0dB 0001=+1dB 0010=+2dB … (1dB steps) 1011=+11dB 1100=+12dB 1101 to 1111=reserved 27 (1Bh) 8 NFU 0 Notch filter update. The notch filter values used internally only update when one of the NFU bits is set high. Analogue to Digital Converter (ADC) 7 NFEN 0 Notch filter enable: Analogue to Digital Converter (ADC) 0=Disabled 1=Enabled 28 (1Ch) 6:0 NFA0[13:7] 0000000 Notch Filter a0 coefficient, bits [13:7] Analogue to Digital Converter (ADC) 8 NFU 0 Notch filter update. The notch filter values used internally only update when one of the NFU bits is set high. Analogue to Digital Converter (ADC) 0 Reserved 0000000 Notch Filter a0 coefficient, bits [6:0] 7 6:0 NFA0[6:0] w Analogue to Digital Converter (ADC) PP, Rev 3.8, May 2012 103 WM8980 Pre-Production REGISTER ADDRESS 29 (1Dh) BIT 8 LABEL NFU 7 30 (1Eh) DESCRIPTION 0 Notch filter update. The notch filter values used internally only update when one of the NFU bits is set high. 0 Reserved REFER TO Analogue to Digital Converter (ADC) 6:0 NFA1[13:7] 0000000 Notch Filter a1 coefficient, bits [13:7] Analogue to Digital Converter (ADC) 8 NFU 0 Notch filter update. The notch filter values used internally only update when one of the NFU bits is set high. Analogue to Digital Converter (ADC) 7 32 (20h) DEFAULT 0 Reserved 6:0 NFA1[6:0] 0000000 Notch Filter a1 coefficient, bits [6:0] Analogue to Digital Converter (ADC) 8:7 ALCSEL 00 ALC function select: Input Limiter/ Automatic Level Control (ALC) 00=ALC off 01=ALC right only 10=ALC left only 11=ALC both on 6 5:3 0 ALCMAXGAIN 111 Reserved Set Maximum Gain of PGA 111=+35.25dB 110=+29.25dB 101=+23.25dB Input Limiter/ Automatic Level Control (ALC) 100=+17.25dB 011=+11.25dB 010=+5.25dB 001=-0.75dB 000=-6.75dB 2:0 ALCMINGAIN 000 Set minimum gain of PGA 000=-12dB 001=-6dB 010=0dB Input Limiter/ Automatic Level Control (ALC) 011=+6dB 100=+12dB 101=+18dB 110=+24dB 111=+30dB 33 (21h) 8 ALCZC 0 ALC Zero Cross Control 0 = ALCZC off 1 = ALCZC on (only valid when ALCMODE=0. ALCZC should not be used when ALCMODE=1) 7:4 ALCHLD 0000 ALC hold time before gain is increased. 0000 = 0ms 0001 = 2.67ms 0010 = 5.33ms Input Limiter/ Automatic Level Control (ALC) Input Limiter/ Automatic Level Control (ALC) … (time doubles with every step) 1010 or higher = 1.36s w PP, Rev 3.8, May 2012 104 WM8980 Pre-Production REGISTER ADDRESS BIT 3:0 LABEL ALCLVL DEFAULT 1011 DESCRIPTION REFER TO ALC target – sets signal level at ADC input 1111 : -1.5dBFS 1110 : -1.5dBFS 1101 : -3dBFS Input Limiter/ Automatic Level Control (ALC) 1100 : -4.5dBFS ...... (-1.5dB steps) 0001 : -21dBFS 0000 : -22.5dBFS 34 (22h) 8 ALCMODE 0 Determines the ALC mode of operation: Input Limiter/ Automatic Level Control (ALC) 0=ALC mode 1=Limiter mode 7:4 ALCDCY 0011 [3:0] Decay (gain ramp-up) time (ALCMODE ==0) Per step Per 6dB 90% of range 0000 410us 3.28ms 23.6ms 0001 820us 6.56ms 47.2ms 0010 1.64ms 13.1ms 94.5ms Input Limiter/ Automatic Level Control (ALC) … (time doubles with every step) 1010 or higher 0011 420ms 3.36s 24.2s Per 6dB 90% of range Decay (gain ramp-up) time (ALCMODE ==1) Per step 0000 90.8us 726us 5.23ms 0001 182us 1.45ms 10.5ms 0010 363us 2.91ms 20.9ms … (time doubles with every step) 1010 3:0 ALCATK 0010 93ms 744ms 5.39s ALC attack (gain ramp-down) time (ALCMODE == 0) Per step Per 6dB 90% of range 0000 104us 832us 6ms 0001 208us 1.66ms 12ms 0010 416us 3.33ms 24ms Input Limiter/ Automatic Level Control (ALC) … (time doubles with every step) 1010 or higher 0010 106ms 852ms 6.13s ALC attack (gain ramp-down) time (ALCMODE == 1) Per step Per 6dB 90% of range 0000 22.7us 182us 1.31ms 0001 45.4us 363us 2.62ms 0010 90.8us 726us 5.23ms … (time doubles with every step) 1010 35 (23h) 8:4 w 00000 23.2ms 186ms 1.34s Reserved PP, Rev 3.8, May 2012 105 WM8980 Pre-Production REGISTER ADDRESS BIT 3 LABEL NGEN DEFAULT 0 DESCRIPTION ALC Noise gate function enable 1 = enable 0 = disable 2:0 NGTH 000 ALC Noise gate threshold: 000=-39dB 001=-45dB 010=-51db REFER TO Input Limiter/ Automatic Level Control (ALC) Input Limiter/ Automatic Level Control (ALC) … (6dB steps) 111=-81dB 36 (24h) 8:5 0000 Reserved 0 Divide MCLK by 2 before input to PLL Master Clock and Phase Locked Loop (PLL) PLLN[3:0] 1000 Integer (N) part of PLL input/output frequency ratio. Use values greater than 5 and less than 13. Master Clock and Phase Locked Loop (PLL) 000 Reserved 5:0 PLLK[23:18] 01100 Fractional (K) part of PLL1 input/output frequency ratio (treat as one 24-digit binary number). Master Clock and Phase Locked Loop (PLL) 38 (26h) 8:0 PLLK[17:9] 010010011 Fractional (K) part of PLL1 input/output frequency ratio (treat as one 24-digit binary number). Master Clock and Phase Locked Loop (PLL) 39 (27h) 8:0 PLLK[8:0] 011101001 Fractional (K) part of PLL1 input/output frequency ratio (treat as one 24-digit binary number). Master Clock and Phase Locked Loop (PLL) 000000 Reserved 4 PLL PRESCALE 3:0 37 (25h) 40 (28h) 8:6 8:2 4 QBOOST 0 Increases ‘Q’ of video filter Video Buffer 1 VBGAIN 0 Video buffer gain Video Buffer 0 = 0dB (=6dB unloaded) 1 = +6dB (=12dB unloaded) 0 VBCLAMPEN 0 Video buffer clamp enable Video Buffer 0 = disabled 1 = enabled 41 (29h) 8:4 3:0 DEPTH3D 00000 Reserved 0000 Stereo depth 0000: 0% (minimum 3D effect) 3D Stereo Enhancement 0001: 6.67% .... 1110: 93.3% 1111: 100% (maximum 3D effect) 43 (2Bh) 8:6 5 MUTERPGA 000 Reserved 0 Mute input to INVROUT2 mixer Analogue Outputs 0 Invert ROUT2 Output Analogue Outputs 2INV 4 INVROUT2 w PP, Rev 3.8, May 2012 106 WM8980 Pre-Production REGISTER ADDRESS BIT 3:1 LABEL BEEPVOL DEFAULT 000 DESCRIPTION REFER TO AUXR input to ROUT2 inverter gain Analogue Outputs 000 = -15dB ... 111 = +6dB 0 BEEPEN 0 0 = mute AUXR beep input Analogue Outputs 1 = enable AUXR beep input 44 (2Ch) 8 MBVSEL 0 Microphone Bias Voltage Control Input Signal Path 0 = 0.9 * AVDD 1 = 0.6 * AVDD 7 6 R2_2INP 0 Reserved 0 Connect R2 pin to right channel input PGA positive terminal. PGA Input Signal Path 0=R2 not connected to input PGA 1=R2 connected to input PGA amplifier positive terminal (constant input impedance). 5 RIN2INP 1 PGA Connect RIN pin to right channel input PGA negative terminal. Input Signal Path 0=RIN not connected to input PGA 1=RIN connected to right channel input PGA amplifier negative terminal. 4 RIP2INP 1 PGA Input Signal Path Connect RIP pin to right channel input PGA amplifier positive terminal. 0 = RIP not connected to input PGA 1 = right channel input PGA amplifier positive terminal connected to RIP (constant input impedance) 3 2 L2_2INP 0 Reserved 0 Connect L2 pin to left channel input PGA positive terminal. PGA Input Signal Path 0=L2 not connected to input PGA 1=L2 connected to input PGA amplifier positive terminal (constant input impedance). 1 LIN2INP 1 PGA Connect LIN pin to left channel input PGA negative terminal. Input Signal Path 0=LIN not connected to input PGA 1=LIN connected to input PGA amplifier negative terminal. 0 LIP2INP 1 PGA Connect LIP pin to left channel input PGA amplifier positive terminal. Input Signal Path 0 = LIP not connected to input PGA 1 = input PGA amplifier positive terminal connected to LIP (constant input impedance) 45 (2Dh) 8 INPPGA N/A UPDATE 7 INPPGAZCL 0 INPPGAVOLL and INPPGAVOLR volume do not update until a 1 is written to INPPGAUPDATE (in reg 45 or 46) Input Signal Path Left channel input PGA zero cross enable: Input Signal Path 0=Update gain when gain register changes st 1=Update gain on 1 zero cross after gain register write. 6 INPPGA MUTEL 0 Mute control for left channel input PGA: 0=Input PGA not muted, normal operation Input Signal Path 1=Input PGA muted (and disconnected from the following input BOOST stage). w PP, Rev 3.8, May 2012 107 WM8980 Pre-Production REGISTER ADDRESS BIT 5:0 LABEL INPPGA DEFAULT 010000 VOLL DESCRIPTION Left channel input PGA volume 000000 = -12dB REFER TO Input Signal Path 000001 = -11.25db . 010000 = 0dB . 111111 = 35.25dB 46 (2Eh) 8 INPPGA N/A UPDATE 7 INPPGA 0 ZCR INPPGAVOLL and INPPGAVOLR volume do not update until a 1 is written to INPPGAUPDATE (in reg 45 or 46) Input Signal Path Right channel input PGA zero cross enable: Input Signal Path 0=Update gain when gain register changes st 1=Update gain on 1 zero cross after gain register write. 6 INPPGA 0 MUTER Mute control for right channel input PGA: 0=Input PGA not muted, normal operation Input Signal Path 1=Input PGA muted (and disconnected from the following input BOOST stage). 5:0 INPPGA 010000 VOLR Right channel input PGA volume 000000 = -12dB Input Signal Path 000001 = -11.25db . 010000 = 0dB . 111111 = +35.25dB 47 (2Fh) 8 PGA 1 BOOSTL Boost enable for left channel input PGA: 0 = PGA output has +0dB gain through input BOOST stage. Input Signal Path 1 = PGA output has +20dB gain through input BOOST stage. 7 6:4 L2_2 0 Reserved 000 Controls the L2 pin to the left channel input boost stage: BOOSTVOL Input Signal Path 000=Path disabled (disconnected) 001=-12dB gain through boost stage 010=-9dB gain through boost stage … 111=+6dB gain through boost stage 3 2:0 AUXL2 0 Reserved 000 Controls the auxiliary amplifer to the left channel input boost stage: BOOSTVOL Input Signal Path 000=Path disabled (disconnected) 001=-12dB gain through boost stage 010=-9dB gain through boost stage … 111=+6dB gain through boost stage 48 (30h) 8 PGA 1 BOOSTR Boost enable for right channel input PGA: 0 = PGA output has +0dB gain through input BOOST stage. Input Signal Path 1 = PGA output has +20dB gain through input BOOST stage. 7 w 0 Reserved PP, Rev 3.8, May 2012 108 WM8980 Pre-Production REGISTER ADDRESS BIT 6:4 LABEL R2_2 DEFAULT 000 BOOSTVOL DESCRIPTION Controls the R2 pin to the right channel input boost stage: REFER TO Input Signal Path 000=Path disabled (disconnected) 001=-12dB gain through boost stage 010=-9dB gain through boost stage … 111=+6dB gain through boost stage 3 2:0 AUXR2 0 Reserved 000 Controls the auxiliary amplifer to the right channel input boost stage: BOOSTVOL Input Signal Path 000=Path disabled (disconnected) 001=-12dB gain through boost stage 010=-9dB gain through boost stage … 111=+6dB gain through boost stage 49 (31h) 8:7 6 DACL2RMIX 00 Reserved 0 Left DAC output to right output mixer 0 = not selected Analogue Outputs 1 = selected 5 DACR2LMIX 0 Right DAC output to left output mixer 0 = not selected Analogue Outputs 1 = selected 4 OUT4 0 0 = OUT4 output gain = -1; BOOST DC = AVDD / 2 Analogue Outputs 1 = OUT4 output gain = +1.5 DC = 1.5 x AVDD / 2 3 OUT3 0 0 = OUT3 output gain = -1; BOOST DC = AVDD / 2 Analogue Outputs 1 = OUT3 output gain = +1.5 DC = 1.5 x AVDD / 2 2 SPKBOOST 0 0 = speaker gain = -1; DC = AVDD / 2 Analogue Outputs 1 = speaker gain = +1.5; DC = 1.5 x AVDD / 2 1 TSDEN 1 Thermal Shutdown Enable 0 : thermal shutdown disabled 1 : thermal shutdown enabled 0 VROI 0 VREF (AVDD/2 or 1.5xAVDD/2) to analogue output resistance Analogue Outputs Analogue Outputs 0: approx 1k 1: approx 30 k 50 (32h) 8:6 AUXLMIX 000 VOL Aux left channel input to left mixer volume control: 000 = -15dB Analogue Outputs 001 = -12dB … 101 = 0dB 110 = +3dB 111 = +6dB 5 AUXL2L MIX 0 Left Auxiliary input to left channel output mixer: 0 = not selected Analogue Outputs 1 = selected w PP, Rev 3.8, May 2012 109 WM8980 Pre-Production REGISTER ADDRESS BIT 4:2 LABEL BYPLMIX DEFAULT 000 VOL DESCRIPTION Left bypass volume control to output channel mixer: REFER TO Analogue Outputs 000 = -15dB 001 = -12dB … 101 = 0dB 110 = +3dB 111 = +6dB 1 BYPL2L 0 MIX Left bypass path (from the left channel input boost output) to left output mixer Analogue Outputs 0 = not selected 1 = selected 0 DACL2L 1 MIX Left DAC output to left output mixer 0 = not selected Analogue Outputs 1 = selected 51 (33h) 8:6 AUXRMIX 000 VOL Aux right channel input to right mixer volume control: Analogue Outputs 000 = -15dB 001 = -12dB … 101 = 0dB 110 = +3dB 111 = +6dB 5 AUXR2R 0 MIX Right Auxiliary input to right channel output mixer: 0 = not selected Analogue Outputs 1 = selected 4:2 BYPRMIX 000 VOL Right bypass volume control to output channel mixer: Analogue Outputs 000 = -15dB 001 = -12dB … 101 = 0dB 110 = +3dB 111 = +6dB 1 BYPR2R 0 MIX Right bypass path (from the right channel input boost output) to right output mixer Analogue Outputs 0 = not selected 1 = selected 0 DACR2R 1 MIX Right DAC output to right output mixer 0 = not selected Analogue Outputs 1 = selected 52 (34h) 8 HPVU N/A 7 LOUT1ZC 0 LOUT1 and ROUT1 volumes do not update until a 1 is written to HPVU (in reg 52 or 53) Analogue Outputs Headphone volume zero cross enable: Analogue Outputs 1 = Change gain on zero cross only 0 = Change gain immediately 6 LOUT1 MUTE 0 Left headphone output mute: 0 = Normal operation Analogue Outputs 1 = Mute w PP, Rev 3.8, May 2012 110 WM8980 Pre-Production REGISTER ADDRESS BIT 5:0 LABEL LOUT1VOL DEFAULT 111001 DESCRIPTION Left headphone output volume: 000000 = -57dB REFER TO Analogue Outputs ... 111001 = 0dB ... 111111 = +6dB 53 (35h) 8 HPVU N/A 7 ROUT1ZC 0 LOUT1 and ROUT1 volumes do not update until a 1 is written to HPVU (in reg 52 or 53) Analogue Outputs Headphone volume zero cross enable: Analogue Outputs 1 = Change gain on zero cross only 0 = Change gain immediately 6 ROUT1 0 MUTE Right headphone output mute: 0 = Normal operation Analogue Outputs 1 = Mute 5:0 ROUT1VOL 111001 Right headphone output volume: 000000 = -57dB Analogue Outputs ... 111001 = 0dB ... 111111 = +6dB 54 (36h) 8 SPKVU N/A 7 LOUT2ZC 0 LOUT2 and ROUT2 volumes do not update until a 1 is written to SPKVU (in reg 54 or 55) Analogue Outputs Speaker volume zero cross enable: Analogue Outputs 1 = Change gain on zero cross only 0 = Change gain immediately 6 LOUT2 0 MUTE Left speaker output mute: 0 = Normal operation Analogue Outputs 1 = Mute 5:0 LOUT2VOL 111001 Left speaker output volume: 000000 = -57dB Analogue Outputs ... 111001 = 0dB ... 111111 = +6dB 55 (37h) 8 SPKVU N/A 7 ROUT2ZC 0 LOUT2 and ROUT2 volumes do not update until a 1 is written to SPKVU (in reg 54 or 55) Analogue Outputs Speaker volume zero cross enable: Analogue Outputs 1 = Change gain on zero cross only 0 = Change gain immediately 6 ROUT2 0 MUTE Right speaker output mute: 0 = Normal operation Analogue Outputs 1 = Mute 5:0 ROUT2VOL 111001 Right speaker output volume: 000000 = -57dB Analogue Outputs ... 111001 = 0dB ... 111111 = +6dB 56 (38h) 8:7 6 00 OUT3MUTE 0 Reserved 0 = Output stage outputs OUT3 mixer 1 = Output stage muted – drives out VMID. Can be used as VMID buffer in this mode. 5:4 w 00 Analogue Outputs Reserved PP, Rev 3.8, May 2012 111 WM8980 Pre-Production REGISTER ADDRESS BIT 3 LABEL OUT4_2OUT3 DEFAULT 0 DESCRIPTION OUT4 mixer output to OUT3 0 = disabled REFER TO Analogue Outputs 1= enabled 2 BYPL2OUT3 0 Left ADC input to OUT3 0 = disabled Analogue Outputs 1= enabled 1 LMIX2OUT3 0 Left DAC mixer to OUT3 0 = disabled Analogue Outputs 1= enabled 0 LDAC2OUT3 1 Left DAC output to OUT3 0 = disabled Analogue Outputs 1= enabled 57 (39h) 8:7 6 00 OUT4MUTE 0 Reserved 0 = Output stage outputs OUT4 mixer 1 = Output stage muted – drives out VMID. Can be used as VMID buffer in this mode. 5 HALFSIG 0 0=OUT4 normal output 1=OUT4 attenuated by 6dB 4 LMIX2OUT4 0 Left DAC mixer to OUT4 0 = disabled Analogue Outputs Analogue Outputs Analogue Outputs 1= enabled 3 LDAC2OUT4 0 Left DAC to OUT4 0 = disabled Analogue Outputs 1= enabled 2 BYPR2OUT4 0 Right ADC input to OUT4 0 = disabled Analogue Outputs 1= enabled 1 RMIX2OUT4 0 Right DAC mixer to OUT4 0 = disabled Analogue Outputs 1= enabled 0 RDAC2OUT4 1 Right DAC output to OUT4 0 = disabled Analogue Outputs 1= enabled w PP, Rev 3.8, May 2012 112 WM8980 Pre-Production DIGITAL FILTER CHARACTERISTICS PARAMETER TEST CONDITIONS MIN +/- 0.025dB 0 TYP MAX UNIT ADC Filter Passband -6dB 0.454fs 0.5fs Passband Ripple +/- 0.025 Stopband Stopband Attenuation dB 0.546fs f > 0.546fs -60 Group Delay dB 21/fs ADC High Pass Filter High Pass Filter Corner Frequency -3dB 3.7 -0.5dB 10.4 -0.1dB 21.6 Hz DAC Filter Passband +/- 0.035dB 0 -6dB 0.454fs 0.5fs Passband Ripple +/-0.035 Stopband Stopband Attenuation Group Delay dB 0.546fs f > 0.546fs -55 dB 29/fs Table 72 Digital Filter Characteristics TERMINOLOGY 1. Stop Band Attenuation (dB) – the degree to which the frequency spectrum is attenuated (outside audio band) 2. Pass-band Ripple – any variation of the frequency response in the pass-band region w PP, Rev 3.8, May 2012 113 WM8980 Pre-Production DAC FILTER RESPONSES 3.05 0 3 -20 2.95 -40 Response (dB) Response (dB) 20 -60 -80 -100 2.9 2.85 2.8 2.75 -120 2.7 -140 2.65 2.6 -160 0 0.5 1 1.5 2 0 2.5 0.05 0.1 0.15 Figure 55 DAC Digital Filter Frequency Response (128xOSR) 0.25 0.3 0.35 0.4 0.45 0.5 0.45 0.5 Figure 56 DAC Digital Filter Ripple (128xOSR) 3.05 20 0 3 -20 2.95 -40 Response (dB) Response (dB) 0.2 Frequency (fs) Frequency (fs) -60 -80 -100 2.9 2.85 2.8 2.75 -120 2.7 -140 2.65 2.6 -160 0 0.5 1 1.5 2 0 2.5 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 Frequency (fs) Frequency (fs) Figure 57 DAC Digital Filter Frequency Response (64xOSR) Figure 58 DAC Digital Filter Ripple (64xOSR) ADC FILTER RESPONSES 0.2 0 0.15 0.1 Response (dB) Response (dB) -20 -40 -60 -80 0.05 0 -0.05 -0.1 -100 -0.15 -0.2 -120 0 0.5 1 1.5 2 Frequency (Fs) Figure 59 ADC Digital Filter Frequency Response w 2.5 3 0 0.1 0.2 0.3 0.4 0.5 Frequency (Fs) Figure 60 ADC Digital Filter Ripple PP, Rev 3.8, May 2012 114 WM8980 Pre-Production HIGHPASS FILTER The WM8980 has a selectable digital highpass filter in the ADC filter path. This filter has two modes, st audio and applications. In audio mode the filter is a 1 order IIR with a cut-off of around 3.7Hz. In nd applications mode the filter is a 2 order high pass filter with a selectable cut-off frequency. 5 0 -5 Response (dB) -10 -15 -20 -25 -30 -35 -40 0 5 10 15 20 25 30 35 40 45 Frequency (Hz) Figure 61 ADC Highpass Filter Response, HPFAPP=0 10 10 0 0 -10 -20 Response (dB) Response (dB) -10 -20 -30 -30 -40 -50 -40 -60 -50 -70 -80 -60 0 200 400 600 800 1000 1200 0 200 400 600 800 1000 1200 Frequency (Hz) Frequency (Hz) Figure 62 ADC Highpass Filter Responses (48kHz), Figure 63 ADC Highpass Filter Responses (24kHz), HPFAPP=1, all cut-off settings shown. HPFAPP=1, all cut-off settings shown. 10 0 -10 Response (dB) -20 -30 -40 -50 -60 -70 -80 -90 0 200 400 600 800 1000 1200 Frequency (Hz) Figure 64 ADC Highpass Filter Responses (12kHz), HPFAPP=1, all cut-off settings shown. w PP, Rev 3.8, May 2012 115 WM8980 Pre-Production 5-BAND EQUALISER 15 15 10 10 5 5 Magnitude (dB) Magnitude (dB) The WM8980 has a 5-band equaliser which can be applied to either the ADC path or the DAC path. The plots from Figure 65 to Figure 78 show the frequency responses of each filter with a sampling frequency of 48kHz, firstly showing the different cut-off/centre frequencies with a gain of 12dB, and secondly a sweep of the gain from -12dB to +12dB for the lowest cut-off/centre frequency of each filter. 0 -5 -5 -10 -10 -15 -1 10 10 0 10 1 2 10 Frequency (Hz) 10 3 10 4 10 -15 -1 10 5 Figure 65 EQ Band 1 Low Frequency Shelf Filter Cut-offs 15 15 10 10 5 5 0 -5 -10 -10 10 0 10 1 2 10 Frequency (Hz) 10 3 10 4 10 5 Figure 67 EQ Band 2 – Peak Filter Centre Frequencies, EQ2BW=0 0 10 1 2 10 Frequency (Hz) 10 3 10 4 10 5 0 -5 -15 -1 10 10 Figure 66 EQ Band 1 Gains for Lowest Cut-off Frequency Magnitude (dB) Magnitude (dB) 0 -15 -1 10 Figure 68 10 0 10 1 2 10 Frequency (Hz) 10 3 10 4 10 5 EQ Band 2 – Peak Filter Gains for Lowest Cut-off Frequency, EQ2BW=0 15 10 Magnitude (dB) 5 0 -5 -10 -15 -2 10 10 -1 10 0 1 10 Frequency (Hz) 10 2 10 3 10 4 Figure 69 EQ Band 2 – EQ2BW=0, EQ2BW=1 w PP, Rev 3.8, May 2012 116 WM8980 15 15 10 10 5 5 Magnitude (dB) Magnitude (dB) Pre-Production 0 0 -5 -5 -10 -10 -15 -1 10 10 0 10 1 2 10 Frequency (Hz) 10 3 10 4 10 5 -15 -1 10 Figure 70 EQ Band 3 – Peak Filter Centre Frequencies, EQ3B Figure 71 10 0 10 1 2 10 Frequency (Hz) 10 3 10 4 10 5 EQ Band 3 – Peak Filter Gains for Lowest Cut-off Frequency, EQ3BW=0 15 10 Magnitude (dB) 5 0 -5 -10 -15 -2 10 10 -1 10 0 1 10 Frequency (Hz) 10 2 10 3 10 4 Figure 72 EQ Band 3 – EQ3BW=0, EQ3BW=1 w PP, Rev 3.8, May 2012 117 Pre-Production 15 15 10 10 5 5 Magnitude (dB) Magnitude (dB) WM8980 0 0 -5 -5 -10 -10 -15 -1 10 10 0 10 1 2 10 Frequency (Hz) 10 3 10 4 10 -15 -1 10 5 Figure 73 EQ Band 4 – Peak Filter Centre Frequencies, EQ3B Figure 74 10 0 10 1 2 10 Frequency (Hz) 10 3 10 4 10 5 EQ Band 4 – Peak Filter Gains for Lowest Cut-off Frequency, EQ4BW=0 15 10 Magnitude (dB) 5 0 -5 -10 -15 -2 10 10 -1 10 0 1 10 Frequency (Hz) 10 2 10 3 10 4 15 15 10 10 5 5 Magnitude (dB) Magnitude (dB) Figure 75 EQ Band 4 – EQ3BW=0, EQ3BW=1 0 0 -5 -5 -10 -10 -15 -1 10 10 0 10 1 2 10 Frequency (Hz) 10 3 10 4 10 5 Figure 76 EQ Band 5 High Frequency Shelf Filter Cut-offs w -15 -1 10 10 0 10 1 2 10 Frequency (Hz) 10 3 10 4 10 5 Figure 77 EQ Band 5 Gains for Lowest Cut-off Frequency PP, Rev 3.8, May 2012 118 WM8980 Pre-Production Figure 78 shows the result of having the gain set on more than one channel simultaneously. The blue traces show each band (lowest cut-off/centre frequency) with 12dB gain. The red traces show the cumulative effect of all bands with +12dB gain and all bands -12dB gain, with EqxBW=0 for the peak filters. 20 15 Magnitude (dB) 10 5 0 -5 -10 -15 -1 10 10 0 10 1 2 10 Frequency (Hz) 10 3 10 4 10 5 Figure 78 Cumulative Frequency Boost/Cut w PP, Rev 3.8, May 2012 119 WM8980 Pre-Production APPLICATION INFORMATION RECOMMENDED EXTERNAL COMPONENTS Figure 79 Recommended External Component Diagram w PP, Rev 3.8, May 2012 120 WM8980 Pre-Production PACKAGE DIAGRAM FL: 40 PIN QFN PLASTIC PACKAGE 6 X 6 X 0.9 mm BODY, 0.50 mm LEAD PITCH D2 31 DM105.A DETAIL 1 40 D 1 30 EXPOSED GROUND 6 PADDLE INDEX AREA (D/2 X E/2) 4 A E E2 21 10 aaa C 2X 11 20 L e b BOTTOM VIEW 1 bbb M C A B aaa C 2X TOP VIEW ccc C A3 A 0.08 C SIDE VIEW C 5 A1 DETAIL 2 SEATING PLANE W 45° 0.35mm EXPOSED GROUND PADDLE T A3 G H b Exposed lead Symbols A A1 A3 b D D2 E E2 e G H L T W MIN 0.80 0 0.18 4.00 4.00 0.30 Half etch tie bar Dimensions (mm) NOM MAX 0.90 1.00 0.02 0.05 0.20 REF 0.25 6.00 BSC 4.15 6.00 BSC 4.15 0.50 BSC 0.2 0.1 0.40 0.103 DETAIL 1 DETAIL 2 NOTE 0.30 1 4.25 2 4.25 2 0.50 0.15 Tolerances of Form and Position aaa bbb ccc REF: 0.15 0.10 0.10 JEDEC, MO-220, VARIATION VJJD-2. NOTES: 1. DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.15 mm AND 0.30 mm FROM TERMINAL TIP. 2. FALLS WITHIN JEDEC, MO-220, VARIATION VJJD-2. 3. ALL DIMENSIONS ARE IN MILLIMETRES. 4. THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL CONFORM TO JEDEC 95-1 SPP-002. 5. COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS. 6. REFER TO APPLICATION NOTE WAN_0118 FOR FURTHER INFORMATION REGARDING PCB FOOTPRINTS AND QFN PACKAGE SOLDERING. 7. DEPENDING ON THE METHOD OF LEAD TERMINATION AT THE EDGE OF THE PACKAGE, PULL BACK (L1) MAY BE PRESENT. 8. THIS DRAWING IS SUBJECT TO CHANGE WITHOUT NOTICE. w PP, Rev 3.8, May 2012 121 WM8980 Pre-Production IMPORTANT NOTICE Wolfson Microelectronics plc (“Wolfson”) products and services are sold subject to Wolfson’s terms and conditions of sale, delivery and payment supplied at the time of order acknowledgement. Wolfson warrants performance of its products to the specifications in effect at the date of shipment. Wolfson reserves the right to make changes to its products and specifications or to discontinue any product or service without notice. Customers should therefore obtain the latest version of relevant information from Wolfson to verify that the information is current. Testing and other quality control techniques are utilised to the extent Wolfson deems necessary to support its warranty. Specific testing of all parameters of each device is not necessarily performed unless required by law or regulation. In order to minimise risks associated with customer applications, the customer must use adequate design and operating safeguards to minimise inherent or procedural hazards. Wolfson is not liable for applications assistance or customer product design. The customer is solely responsible for its selection and use of Wolfson products. Wolfson is not liable for such selection or use nor for use of any circuitry other than circuitry entirely embodied in a Wolfson product. Wolfson’s products are not intended for use in life support systems, appliances, nuclear systems or systems where malfunction can reasonably be expected to result in personal injury, death or severe property or environmental damage. Any use of products by the customer for such purposes is at the customer’s own risk. Wolfson does not grant any licence (express or implied) under any patent right, copyright, mask work right or other intellectual property right of Wolfson covering or relating to any combination, machine, or process in which its products or services might be or are used. Any provision or publication of any third party’s products or services does not constitute Wolfson’s approval, licence, warranty or endorsement thereof. Any third party trade marks contained in this document belong to the respective third party owner. Reproduction of information from Wolfson datasheets is permissible only if reproduction is without alteration and is accompanied by all associated copyright, proprietary and other notices (including this notice) and conditions. Wolfson is not liable for any unauthorised alteration of such information or for any reliance placed thereon. Any representations made, warranties given, and/or liabilities accepted by any person which differ from those contained in this datasheet or in Wolfson’s standard terms and conditions of sale, delivery and payment are made, given and/or accepted at that person’s own risk. Wolfson is not liable for any such representations, warranties or liabilities or for any reliance placed thereon by any person. ADDRESS: Wolfson Microelectronics plc Westfield House 26 Westfield Road Edinburgh EH11 2QB United Kingdom Tel :: +44 (0)131 272 7000 Fax :: +44 (0)131 272 7001 Email :: [email protected] w PP, Rev 3.8, May 2012 122 WM8980 Pre-Production REVISION HISTORY DATE REV ORIGINATOR CHANGES 01/11/11 3.8 JMacD Order codes changed from WM8980GEFL/R and WM8980GEFL/RV to WM8980CGEFL/V and WM8980CGEFL/RV to reflect change to copper wire bonding. 01/11/11 3.8 JMacD Package Diagram changed to DM105.A. 05/01/12 3.8 BK w Corrected GPIO4SEL description. PP, Rev 3.8, May 2012 123