VISHAY Y163110R0000T9W

VFCP Series (0805, 1206, 1506, 2010, 2512) (Z-Foil)
Vishay Foil Resistors
Ultra High Precision Z-Foil Flip Chip Resistor with TCR
of ± 0.05 ppm/°C, 35 % Space Saving versus
Wraparound Design and PCR of 5 ppm at Rated Power
FEATURES
PR
O
DU
CT
Any value at tolerance available within resistance range
INTRODUCTION
One of the most important parameters influencing stability is
the Temperature Coefficient of Resistance (TCR). Although
the TCR of Bulk Metal® Foil resistors is considered extremely
low, this characteristic has been further refined over the
years.
The VFCP Series utilizes ultra precision Bulk Metal® Z-Foil.
The Z-Foil technology provides a significant reduction to the
resistive element’s sensitivity to ambient temperature
variations (TCR) and to self heating when power is applied
(power coefficient).
IM
PR
O
VE
D
Along with the inherently low PCR and TCR, Z-Foil
technology also provides remarkably improved load life
stablility, low noise and availability of tight tolerance.
The Flip Chip configuration provides a substantial PCB
space saving of more than 35 % vs. a surface mount chip
with wraparound terminations. The VFCP is available in any
value within the specified resistance range.
Our Application Engineering Department is available to
advise and make recommendations. For non-standard
technical requirements and special applications, please
contact us.
TABLE 1 - TOLERANCE AND TCR VS
RESISTANCE VALUE
RESISTANCEVALUE
(Ω)
TOLERANCE
(%)
TYPICAL TCR AND
MAX. SPREAD
(- 55 °C to + 125 °C,
+ 25 °C Ref.)
250 to 150K
± 0.01
± 0.2 ± 1.6
100 to < 250
± 0.02
± 0.2 ± 1.6
50 to < 100
± 0.05
± 0.2 ± 1.8
25 to < 50
± 0.1
± 0.2 ± 2.8
10 to < 25
± 0.25
± 0.2 ± 2.8
APPLICATIONS
•
•
•
•
•
•
•
•
•
Automatic Test Equipment (ATE)
High Precision Instrumentation
Laboratory, Industrial and Medical
Audio
EB Applications (electron beam scanning and recording
equipment, electron microscopes)
Military and Space
Airborne
Down Hole instrumentation
Communication
FIGURE 1 - POWER DERATING CURVE
Percent of Rated Power
Bottom View
• Temperature Coefficient of Resistance (TCR):
± 0.05 ppm/°C typical (0 °C to + 60 °C)
Pb-free
Available
± 0.2 ppm/°C typical (- 55 °C to + 125 °C,
+
25 °C Ref.)
RoHS*
• Tolerance: to ± 0.01 % (100 ppm)
COMPLIANT
• Power Coefficient “ΔR due to self heating”
5 ppm at Rated Power
• Load Life Stability (70 °C for 2000 hours):
± 0.005 % (50 ppm)
• Power Rating to: 600 mW at + 70 °C
• Electrostatic Discharge (ESD) above 25 000 V
• Resistance Range: 10Ω to 150 kΩ (for lower and higher
values, please contact us)
• Non Inductive, Non Capacitive Design
• Short time overload ≤ 0.005 % (50 ppm)
• Non hot spot design
• Rise time: 1ns without ringing
• Current Noise: - 40 dB
• Voltage Coefficient < 0.1 ppm/V
• Non Inductive: < 0.08 µH
• Terminal Finishes available: Lead (Pb)-free
Tin/Lead Alloy
• Matched sets are available per request
• Any value available within resistance range (e.g. 1K2345)
• Prototype samples available from 48 hours. For more
information, please contact [email protected]
• For better performances please contact us
+ 70 °C
- 55 °C
100
75
50
25
0
- 75
- 50
- 25
0
+ 25
+ 50
+ 75 + 100 + 125 + 150 + 175
Ambient Temperature (°C)
* Pb containing terminations are not RoHS compliant, exemptions may apply
Document Number: 63106
Revision: 28-Jun-07
For any questions, contact: [email protected]
www.vishay.com
1
VFCP Series (0805, 1206, 1506, 2010, 2512) (Z-Foil)
Vishay Foil Resistors Ultra High Precision Z-Foil Flip Chip Resistor with TCR
of ± 0.05 ppm/°C, 35 % Space Saving versus
Wraparound Design and PCR of 5 ppm at Rated Power
TABLE 2 - DSCC SPECIFICATIONS (Vishay resistors are listed on the following DSCC specifications)
MODEL
DSCC
MIL SPEC
VFCP1206
2009
MIL-PRF-55342
PR
O
DU
CT
Note
• For VFCP0805, VFCP1506, VFCP2010 and VFCP2512 DSCC Drawings, please contact [email protected]
FIGURE 2 -TRIMMING TO VALUES (Conceptual Illustration)
Current Path
Before Trimming
Interloop Capacitance
Reduction in Series
Current Path
After Trimming
Trimming Process
Removes this Material
from Shorting Strip Area
Changing Current Path
and Increasing
Resistance
Mutual Inductance
Reduction due
to Change in
Current Direction
Note: Foil shown in black, etched spaces in white
TABLE 4 - LOAD LIFE STABILITY
(+ 70 °C FOR 2000 HOURS)
TABLE 3 - SPECIFICATIONS
MAXIMUM
VOLTAGE
RATING
(≤ P × R )
RESISTANCE
RANGE (Ω)
MAXIMUM
WEIGHT
(mg)
0805
100 mW
34 V
10 to 12K
5.2
IM
PR
O
VE
D
CHIP
SIZE
RATED
POWER
(mW)
at + 70 °C
CHIP SIZE
MAXIMUM ΔR LIMITS
0805
± 0.005 % at 50 mW
± 0.01 % at 100 mW
1206
± 0.005 % at 150 mW
± 0.01 % at 250 mW
1506
± 0.005 % at 150 mW
± 0.01 % at 300 mW
1206
250 mW
86 V
10 to 30K
10.3
1506
300 mW
109 V
10 to 40K
12
2010
400 mW
200 V
10 to 100K
25
2010
± 0.005 % at 200mW
± 0.01 % at 400 mW
2512
600 mW
220 V
10 to 150K
35
2512
± 0.005 % at 500 mW
± 0.01 % at 600 mW
TABLE 5 - PERFORMANCES
MIL-PRF-55342
CHARACTERISTIC E
ΔR LIMITS
TYPICAL
ΔR LIMITS
MAXIMUM
ΔR LIMITS1)
Thermal Shock
± 0.1 %
± 0.005 % (50 ppm)
± 0.01 % (100 ppm)
Low Temperature Operation
± 0.1 %
± 0.005 % (50 ppm)
± 0.01 % (100 ppm)
Short Time Overload
± 0.1 %
± 0.005 % (50 ppm)
± 0.01 % (100 ppm)
High Temperature Exposure
± 0.1 %
± 0.01 % (100 ppm)
± 0.02 % (200 ppm)
Resistance to Soldering Heat
± 0.2 %
± 0.005 % (50 ppm)
± 0.015 % (150 ppm)
Moisture Resistance
± 0.2 %
± 0.005 % (50 ppm)
± 0.02 % (200 ppm)
Load Life Stability + 70 °C for 2000 hours
at Rated Power
± 0.5 %
± 0.005 % (50 ppm)
± 0.01 % (100 ppm)
TEST OR CONDITION
Note
1. As shown + 0.01 W to allow for measurement errors at low values.
www.vishay.com
2
For any questions, contact: [email protected]
Document Number: 63106
Revision: 28-Jun-07
VFCP Series (0805, 1206, 1506, 2010, 2512) (Z-Foil)
Ultra High Precision Z-Foil Flip Chip Resistor with TCR Vishay Foil Resistors
of ± 0.05 ppm/°C, 35 % Space Saving versus
Wraparound Design and PCR of 5 ppm at Rated Power
TABLE 6 - DIMENSIONS AND LAND PATTERN in inches (millimeters)
BOTTOM VIEW (showing terminals for mounting)
LAND PATTERN
Solder Terminals
PR
O
DU
CT
D
W
L - 0.005 (0.13)
X
G
W1 [W - 0.003"]
Z
L
CHIP
SIZE
L
W
THICKNESS
D
Z1)
G1)
X1)
± 0.005 (0.13)
± 0.005 (0.13)
MAXIMUM
± 0.005 (0.13)
MAXIMUM
MINIMUM
MAXIMUM
0805
0.079 (2.01)
0.049 (1.24)
0.025 (0.64)
0.010 (0.25)
0.078 (1.98)
0.053 (1.35)
0.049 (1.24)
1206
0.126 (3.20)
0.062 (1.57)
0.025 (0.64)
0.015 (0.38)
0.125 (3.18)
0.090 (2.29)
0.062 (1.57)
1506
0.150 (3.81)
0.062 (1.57)
0.025 (0.64)
0.012 (0.30)
0.150 (3.81)
0.120 (3.05)
0.062 (1.57)
2010
0.200 (5.08)
0.100 (2.54)
0.025 (0.64)
0.020 (0.51)
0.199 (5.05)
0.153 (3.89)
0.100 (2.54)
2512
0.250 (6.35)
0.126 (3.20)
0.025 (0.64)
0.024 (0.61)
0.250 (6.35)
0.196 (4.98)
0.126 (3.20)
IM
PR
O
VE
D
Note
1. Land Pattern Dimensions are per IPC-782
FIGURE 3 - CHIP CONFIGURATION
High Purity Alumina Substrate
Resistive
Bulk® Metal Foil
Solder
Protective Coating
Document Number: 63106
Revision: 28-Jun-07
FIGURE 4 - TYPICAL TCR CURVE Z-FOIL
(For more details, see Table 1)
+ 500
+ 400
+ 300
+ 200
+ 100
ΔR
0
R
(ppm)
- 100
0.05 ppm/°C
- 200
- 0.1 ppm/°C
- 300
0.1 ppm/°C
0.14 ppm/°C
- 400
0.2 ppm/°C
- 0.16 ppm/°C
- 500
- 55
- 25
0
+ 25
+ 60 + 75
+ 100 + 125
Ambient Temperature (°C)
Note
• The TCR values for < 100Ω are influenced by the termination
composition and result in deviation from this curve
For any questions, contact: [email protected]
www.vishay.com
3
VFCP Series (0805, 1206, 1506, 2010, 2512) (Z-Foil)
Vishay Foil Resistors Ultra High Precision Z-Foil Flip Chip Resistor with TCR
of ± 0.05 ppm/°C, 35 % Space Saving versus
Wraparound Design and PCR of 5 ppm at Rated Power
TABLE 7 - GLOBAL PART NUMBER INFORMATION
NEW GLOBAL PART NUMBER: Y162910K0000T9W (preferred part number format)
VALUE
AER*
Y
R=Ω
K = kΩ
0 = Standard
9 = Lead (Pb)-free
1 - 999 = Custom
Y
1
6
2
9
1
0
PR
O
DU
CT
DENOTES PRECISION
K
0
0
0
0
T
9
W
PRODUCT CODE
RESISTANCE TOLERANCE
PACKAGING
1629 = VFCP0805
1630 = VFCP1206
1631 = VFCP1506
1632 = VFCP2010
1633 = VFCP2512
T = ± 0.01 %
Q = ± 0.02 %
A = ± 0.05 %
B = ± 0.10 %
C = ± 0.25 %
D = ± 0.50 %
F = ± 1.00 %
R = Tape and Reel
W = Waffle Pack
FOR EXAMPLE: ABOVE GLOBAL ORDER Y1629 10K0000 T 9 W:
TYPE: VFCP0805
VALUE: 10.0 kΩ
ABSOLUTE TOLERANCE: ± 0.01 %
TERMINATION: Lead (Pb)-free
PACKAGING: Waffle Pack
HISTORICAL PART NUMBER: VFCP0805 10K000 TCR0.2 T S W (will continue to be used)
10K000
TCR0.2
MODEL
OHMIC VALUE
TCR
VFCP0805
VFCP1206
VFCP1506
VFCP2010
VFCP2512
10.0 kΩ
Characteristic
IM
PR
O
VE
D
VFCP0805
T
S
W
RESISTANCE
TOLERANCE
TERMINATION
PACKAGING
S = Lead (Pb)-free
B = Tin/Lead
T = Tape and Reel
W = Waffle Pack
T = ± 0.01 %
Q = ± 0.02 %
A = ± 0.05 %
B = ± 0.10 %
C = ± 0.25 %
D = ± 0.50 %
F = ± 1.00 %
Note
* For non-standard requests, please contact Application Engineering.
www.vishay.com
4
For any questions, contact: [email protected]
Document Number: 63106
Revision: 28-Jun-07
Legal Disclaimer Notice
Vishay
Disclaimer
All product specifications and data are subject to change without notice.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf
(collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein
or in any other disclosure relating to any product.
Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any
information provided herein to the maximum extent permitted by law. The product specifications do not expand or
otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed
therein, which apply to these products.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this
document or by any conduct of Vishay.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless
otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such
applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting
from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding
products designed for such applications.
Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000
Revision: 18-Jul-08
www.vishay.com
1