VISHAY Y16363K00000T9W

VSMP0603 (Z-Foil)
Vishay Foil Resistors
Ultra High Precision Foil Wraparound Surface Mount Chip Resistor
with Temperature Coefficient of Resistance of ± 0.05 ppm/°C, Load
Life Stability to ± 0.005 % (50 ppm) and ESD Immunity up to 25 kV
FEATURES
Vishay Foil resistors are not restricted to standard
values, we can supply specific “as required” values at
no extra cost or delivery (e.g. 1K234 vs. 1K).
INTRODUCTION
VSMP series is the industry’s first device to provide high
rated power, excellent load life stability along with extremely
low TCR all in one resistor.
One of the most important parameters influencing stability is
the temperature coefficient of resistance (TCR). Although the
TCR of foil resistors is considered extremely low, this
characteristic has been further refined over the years. The
VSMP series utilizes ultra high precision Bulk Metal® Z-foil.
The Z-foil technology provides a significant reduction of the
resistive element's sensitivity to ambient temperature
variations (TCR) and to self heating when power is applied
(power coefficient). Along with the inherently low PCR and
TCR, Z-foil technology also provides remarkably improved
load life stability, low noise and availability of tight tolerance.
The VSMP0603 has a full wraparound termination which
ensures safe handling during the manufacturing process, as
well as providing stability during multiple thermal cyclings.
Our application engineering department is available to
advise and make recommendations. For non-standard
technical requirements and special applications, please
contact us using the e-mail address in the footer below.
TABLE 1 - TOLERANCE AND TCR VS.
RESISTANCE VALUE (1)
(- 55 °C to + 125 °C, + 25 °C ref.)
RESISTANCE
VALUE
()
TOLERANCE
(%)
APPLICATIONS





Automatic test equipment (ATE)
High precision instrumentation
Laboratory, industrial and medical
Audio
EB applications (electron beam scanning and recording
equipment, electron microscopes)
 Down hole instrumentation
 Communication
TYPICAL TCR AND
MAX. SPREAD
(ppm/°C)
250to 5K
± 0.01
± 0.2 ± 1.8
100to < 250
± 0.02
± 0.2 ± 1.8
Note
(1) For tighter performances, please contact Vishay application
engineering using the e-mail address in the footer below.
FIGURE 1 - POWER DERATING CURVE
Percent of Rated Power
Top View
 Temperature coefficient of resistance (TCR):
0.05 ppm/°C typical (0 °C to + 60 °C)
0.2 ppm/°C typical (- 55 °C to + 125 °C,
+ 25 °C ref.)
 Tolerance: to ± 0.01 %
 Power coefficient “R due to self heating”:
5 ppm at rated power
 Power rating: to 100 mW at + 70 °C
 Load life stability: to ± 0.005 % at 70 °C, 2000 h at rated
power
 Resistance range: 100 to 5 k
 Electrostatic discharge (ESD) up to 25 000 V
 Short time overload:  0.005 %
 Non inductive, non capacitive design
 Rise time: 1 ns effectively no ringing
 Special design which reduces circuit signal distortion
 Current noise: - 40 dB
 Voltage coefficient < 0.1 ppm/V
 Non inductive: < 0.08 µH
 Non hot spot design
 Terminal finishes available: lead (Pb)-free
tin/lead alloy
 Matched sets are available on request
 Prototype samples available from 72 h. For more
information, please contact [email protected]
 For better performances please contact us
+ 70 °C
- 55 °C
100
75
50
25
0
- 75
- 50
- 25
0
+ 25 + 50 + 75 + 100 + 125 + 150 + 175
Ambient Temperature (°C)
* Pb containing terminations are not RoHS compliant, exemptions may apply
Document Number: 63141
Revision: 26-Mar-10
For any questions, contact: [email protected]
www.foilresistors.com
1
VSMP0603 (Z-Foil)
Vishay Foil Resistors
FIGURE 2 - TRIMMING TO VALUES
(Conceptual Illustration)
FIGURE 3 -TYPICAL TCR CURVE Z-FOIL
+ 500
+ 400
+ 300
+ 200
Current Path
Before Trimming
Interloop Capacitance
Reduction in Series
+ 100
ΔR
0
R
(ppm)
- 100
Current Path
After Trimming
Trimming Process
Removes this Material
from Shorting Strip Area
Changing Current Path
and Increasing
Resistance
Mutual Inductance
Reduction due
to Opposing
Current in
Adjacent Lines
0.05 ppm/°C
- 200
- 0.1 ppm/°C
- 300
0.1 ppm/°C
0.14 ppm/°C
- 400
0.2 ppm/°C
- 0.16 ppm/°C
- 500
- 55
- 25
0
+ 25
+ 60 + 75
+ 100 + 125
Ambient Temperature (°C)
Note
• The TCR values for < 100  are influenced by the termination
composition and result in deviation from this curve.
Note: Foil shown in black, etched spaces in white
TABLE 2 - DIMENSIONS AND LAND PATTERN in Inches (Millimeters)
Bottom View for Mounting
Uncoated
Ceramic
L
W
T
D
CHIP SIZE
0603
L
± 0.005 (0.13)
W
± 0.005 (0.13)
THICKNESS MAXIMUM
D
± 0.005 (0.13)
0.063 (1.60)
0.032 (0.81)
0.025 (0.64)
0.011 (0.28)
Note
• Land pattern dimensions are per IPC-782.
TABLE 3 - PERFORMANCES
TEST OR CONDITIONS
PER MIL-PRF-55342
MIL-PRF-55342
CHARACTERISTIC E R LIMITS
TYPICAL R LIMITS
MAXIMUM R LIMITS
Thermal shock:
100 x (- 65 °C to + 150 °C)
± 0.2 %
± 0.005 % (50 ppm)
± 0.01 % (100 ppm)
Low temperature operation:
- 65 °C, 45 min, rated power
± 0.1 %
± 0.005 % (50 ppm)
± 0.01 % (100 ppm)
Short time overload:
6.25 x rated power, 5 s
± 0.1 %
± 0.005 % (50 ppm)
± 0.01 % (100 ppm)
High temperature exposure: 100 h, 150 °C
± 0.1 %
± 0.01 % (100 ppm)
± 0.03 % (300 ppm)
Resistance to soldering heat
± 0.2 %
± 0.005 % (50 ppm)
± 0.02 % (200 ppm)
Moisture resistance
± 0.2 %
± 0.03 % (300 ppm)
± 0.1 % (1000 ppm)
Load life stability + 70 °C for 2000 h
at rated power
± 0.5 %
± 0.005 % (50 ppm)
± 0.01 % (100 ppm)
Note
• As shown + 0.01  to allow for measurement errors at low values.
www.foilresistors.com
2
For any questions, contact: [email protected]
Document Number: 63141
Revision: 26-Mar-10
VSMP0603 (Z-Foil)
Vishay Foil Resistors
FIGURE 4 - VSMP0603 100 CYCLE THERMAL SHOCK - 65 °C TO 150 °C, 10 UNITS EACH VALUE
100
80
ΔR/R (ppm)
60
40
20
0
- 20
- 40
VSMP0603
100R
VSMP0603
1K
VSMP0603
5K
FIGURE 5 - LOAD LIFE STABILITY 2000 h AT + 70 °C, 0.1 W, 20 UNITS EACH VALUE
60
50
ΔR/R (ppm)
40
30
20
10
0
- 10
VSMP0603
100R
VSMP0603
1K
VSMP0603
5K
FIGURE 6 - RECOMMENDED MOUNTING
25 % to 85 % of T
A low profile solder fillet is
recommended to avoid unnecessary
stresses along top edge of
metallization. IR and vapor phase
reflow are best. Avoid the use of
cleaning agents which could attack
epoxy resins, which form part of the
resistor construction.
Notes
(1) Avoid the use of cleaning agents which could attack epoxy resins, which form part of the resistor construction
(2) Vacuum pick up is recommended for handling
(3) Soldering iron may damage the resistor
Document Number: 63141
Revision: 26-Mar-10
For any questions, contact: [email protected]
www.foilresistors.com
3
VSMP0603 (Z-Foil)
Vishay Foil Resistors
TABLE 4 - GLOBAL PART NUMBER INFORMATION
NEW GLOBAL PART NUMBER: Y16363K25200T9R (preferred part number format)
DENOTES PRECISION
VALUE
CHARACTERISTICS (1)
Y
R=
K = k
0 = standard part, tin/lead termination
9 = standard part, lead (Pb)-free termination
1 to 999 = custom
Y
1
6
3
6
3
K
2
5
2
0
0
T
9
PRODUCT CODE
RESISTANCE TOLERANCE
PACKAGING
1636 = VSMP0603
T = ± 0.01 %
Q = ± 0.02 %
A = ± 0.05 %
B = ± 0.10 %
C = ± 0.25 %
D = ± 0.5 %
F = ± 1.0 %
R = tape and reel
W = waffle pack
R
FOR EXAMPLE: ABOVE GLOBAL ORDER Y1636 3K25200 T 9 R:
TYPE: VSMP0603
VALUES: 3.252 k
ABSOLUTE TOLERANCE: 0.01 %
TERMINATION: lead (Pb)-free
PACKAGING: tape and reel
Note
(1) For non-standard requests, please contact application engineering.
www.foilresistors.com
4
For any questions, contact: [email protected]
Document Number: 63141
Revision: 26-Mar-10
Legal Disclaimer Notice
Vishay Precision Group
Disclaimer
ALL PRODUCTS, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Vishay Precision Group, Inc., its affiliates, agents, and employees, and all persons acting on its or their
behalf (collectively, “Vishay Precision Group”), disclaim any and all liability for any errors, inaccuracies or
incompleteness contained herein or in any other disclosure relating to any product.
The product specifications do not expand or otherwise modify Vishay Precision Group’s terms and
conditions of purchase, including but not limited to, the warranty expressed therein.
Vishay Precision Group makes no warranty, representation or guarantee other than as set forth in the terms
and conditions of purchase. To the maximum extent permitted by applicable law, Vishay Precision
Group disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and
all liability, including without limitation special, consequential or incidental damages, and (iii) any and
all implied warranties, including warranties of fitness for particular purpose, non-infringement and
merchantability.
Information provided in datasheets and/or specifications may vary from actual results in different
applications and performance may vary over time. Statements regarding the suitability of products for
certain types of applications are based on Vishay Precision Group’s knowledge of typical requirements that
are often placed on Vishay Precision Group products. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular
application.
No license, express, implied, or otherwise, to any intellectual property rights is granted by this document, or
by any conduct of Vishay Precision Group.
The products shown herein are not designed for use in life-saving or life-sustaining applications unless
otherwise expressly indicated. Customers using or selling Vishay Precision Group products not expressly
indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay
Precision Group for any damages arising or resulting from such use or sale. Please contact authorized
Vishay Precision Group personnel to obtain written terms and conditions regarding products designed for
such applications.
Product names and markings noted herein may be trademarks of their respective owners.
Document No.: 63999
Revision: 27-Apr-2011
www.vishaypg.com
1