ZILOG Z8018008VSG

Z80180
Microprocessor Unit
Product Specification
PS014004-1106
ZiLOG Worldwide Headquarters • 532 Race Street • San Jose, CA 95126
Telephone: 408.558.8500 • Fax: 408.558.8300 • www.zilog.com
This publication is subject to replacement by a later edition. To determine whether
a later edition exists, or to request copies of publications, contact:
ZiLOG Worldwide Headquarters
532 Race Street
San Jose, CA 95126-3432
Telephone: 408.558.8500
Fax: 408.558.8300
www.zilog.com
ZiLOG is a registered trademark of ZiLOG Inc. in the United States and in other countries. All other
products and/or service names mentioned herein may be trademarks of the companies with which
they are associated.
Document Disclaimer
©2006 by ZiLOG, Inc. All rights reserved. Information in this publication concerning the devices,
applications, or technology described is intended to suggest possible uses and may be superseded.
ZiLOG, INC. DOES NOT ASSUME LIABILITY FOR OR PROVIDE A REPRESENTATION OF
ACCURACY OF THE INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED IN THIS
DOCUMENT. ZiLOG ALSO DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY
INFRINGEMENT RELATED IN ANY MANNER TO USE OF INFORMATION, DEVICES, OR
TECHNOLOGY DESCRIBED HEREIN OR OTHERWISE. Devices sold by ZiLOG, Inc. are covered
by warranty and limitation of liability provisions appearing in the ZiLOG, Inc. Terms and Conditions of
Sale. ZiLOG, Inc. makes no warranty of merchantability or fitness for any purpose. Except with the
express written approval of ZiLOG, use of information, devices, or technology as critical components
of life support systems is not authorized. No licenses are conveyed, implicitly or otherwise, by this
document under any intellectual property rights.
PS014004-1106
Z80180
Microprocessor Unit
iii
Revision History
Each instance in the following table reflects a change to this document from its
previous revision. To see more detail, click the appropriate link in the table below.
Date
Revision
Level
November 04
2006
PS014004-1106
Description
Page No
Updated DC Characteristics table and minor edits done
throughout the document.
All
Z80180
Microprocessor Unit
iv
PS014004-1106
Z80180
Microprocessor Unit
v
Table of Contents
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Multiplexed Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Operation Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timing Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ASCI Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ASCI Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ASCI Transmit Data Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ASCI Receive Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ASCI Channel Control Register A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ASCI Channel Control Register B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ASCI Status Register 0, 1 (STAT0, 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CSIO Control/Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CSIO Transmit/Receive Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer Data Register Channel 0L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer Data Register Channel 0H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer Reload Register 0L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer Reload Register 0H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer Control Register (TCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ASCI Extension Control Register Channels 0 and 1 . . . . . . . . . . . . . . . . . . . . .
ASEXT0 and ASEXT1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer Data Register Channel 1L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer Data Register Channel 1H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer Reload Register Channel 1L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer Reload Register Channel 1H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Free Running Counter I/O Address = 18H . . . . . . . . . . . . . . . . . . . . . . . . .
PS014004-1106
15
20
20
21
22
30
37
38
39
40
41
43
45
46
48
48
48
49
49
49
50
50
52
52
53
53
54
Z80180
Microprocessor Unit
vi
DMA Source Address Register Channel 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DMA Source Address Register, Channel 0L . . . . . . . . . . . . . . . . . . . . . . . .
DMA Source Address Register, Channel 0H . . . . . . . . . . . . . . . . . . . . . . .
DMA Source Address Register Channel 0B . . . . . . . . . . . . . . . . . . . . . . . .
DMA Destination Address Register Channel 0 . . . . . . . . . . . . . . . . . . . . . . . . .
DMA Destination Address Register Channel 0L . . . . . . . . . . . . . . . . . . . . .
DMA Destination Address Register Channel 0H . . . . . . . . . . . . . . . . . . . . .
DMA Destination Address Register Channel 0B . . . . . . . . . . . . . . . . . . . . .
DMA Byte Count Register Channel 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DMA Byte Count Register Channel 0L . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DMA Byte Count Register Channel 0H . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DMA Byte Count Register Channel 1L . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DMA Byte Count Register Channel 1H . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DMA Memory Address Register Channel 1 . . . . . . . . . . . . . . . . . . . . . . . . . . .
DMA Memory Address Register, Channel 1L . . . . . . . . . . . . . . . . . . . . . . .
DMA Memory Address Register, Channel 1H . . . . . . . . . . . . . . . . . . . . . . .
DMA Memory Address Register, Channel 1B . . . . . . . . . . . . . . . . . . . . . . .
DMA I/O Address Register Channel 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DMA I/O Address Register Channel 1L . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DMA I/O Address Register Channel 1H . . . . . . . . . . . . . . . . . . . . . . . . . . .
DMA I/O Address Register Channel 1B . . . . . . . . . . . . . . . . . . . . . . . . . . .
DMA Status Register (DSTAT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DMA Mode Register (DMODE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DMA/WAIT Control Register (DCNTL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupt Vector Low Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Int/TRAP Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Refresh Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MMU Common Base Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MMU Bank Base Register (BBR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MMU Common/Bank Area Register (CBAR) . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation Mode Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I/O Control Register (ICR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
54
54
55
55
55
56
56
56
57
57
58
58
59
59
59
60
60
60
61
61
62
62
63
65
66
67
69
71
71
72
72
74
Package Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
PS014004-1106
Z80180
Microprocessor Unit
1
Overview
Features
The key features of Z80180™ microprocessor unit (MPU) include:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Code compatible with ZiLOG Z80® CPU
Extended instructions
Two DMA channels
Low power-down modes
On-chip interrupt controllers
Three on-chip wait-state generators
On-chip oscillator/generator
Expanded MMU addressing (up to 1 MB)
Clocked serial I/O port
Two 16-Bit counter/timers
Two UARTs
Clock Speeds: 6 MHz, 8 MHz, and 10 MHz
6 MHz version supports 6.144 MHz CPU clock operation
Operating range: 5 V
Operating temperature range: 0 ºC to +70 ºC
Three packaging styles
– 68-Pin PLCC
– 64-Pin DIP
– 80-Pin QFP
General Description
The Z80180™ is an 8-bit MPU which provides the benefits of reduced system costs and also
provides full backward compatibility with existing ZiLOG Z80 devices.
Reduced system costs are obtained by incorporating several key system functions on-chip
with the CPU. These key functions include I/O devices such as DMA, UART, and timer
PS014004-1106
Overview
Z80180
Microprocessor Unit
2
channels. Also included on-chip are wait-state generators, a clock oscillator, and an interrupt
controller.
The Z80180™ is housed in 80-pin QFP, 68-pin PLCC, and 64-pin DIP packages.
Note: All signals with an overline are active Low. For example, B/W, in which WORD is
active Low); and B/W, in which BYTE is active Low.
Power connections follow conventional descriptions as listed in Table 1.
Table 1. Power Connection Conventions
Connection
Power
Ground
Circuit
VCC
GND
Device
VDD
VSS
16-Bit
Address Bus
Power Controller
A
MMU
Processor
8-Bit
Data Bus
Decode
B
B
DMACs (2)
Clocked
Serial I/O
16-Bit Programmable
Reload Timers (2)
UARTs (2)
TXA1–0
RXA1–0
Figure 1. Z80180 Functional Block Diagram
PS014004-1106
Overview
Z80180
Microprocessor Unit
3
Pin Configuration
VSS
XTAL
EXTAL
WAIT
BUSACK
BUSREQ
RESET
NMI
INT0
INT1
INT2
ST
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
VCC
1
64
Z80180
64-Pin
32
33
PHI
RD
WR
M1
E
MREQ
IORQ
RFSH
HALT
TEND1
DREQ1
CKS
RXS/CTS1
TXS
CKA1/TEND0
RXA1
TXA1
CKA/DREQ0
RXA0
TXA0
DCD0
CTS0
RTS0
D7
D6
D5
D4
D3
D2
D1
D0
VSS
Figure 2. Z80180 64-Pin Dip Configuration
PS014004-1106
Overview
Z80180
Microprocessor Unit
4
NMI
RESET
BUSREQ
BUSACK
WAIT
EXTAL
XTAL
VSS
VSS
PHI
RD
WR
M1
E
MREQ
IORQ
RFSH
Z80180 68-Pin PLCC Pin Configuration
9
10
1
61
60
Z80180
68-Pin PLCC
26
44
43
A18/TOUT
A12
A13
A14
A15
A16
A17
27
HALT
TENDi
DREQi
CKS
RXS/CTS1
TXS
CKA1/TEND0
RXA1
TEST
TXA1
CKA0/DREQ0
RXA0
TXA0
DCD0
CTS0
RTS0
D7
VCC
A19
VSS
D0
D1
D2
D3
D4
D5
D6
INT0
INT1
INT2
ST
A0
A1
A2
A3
VSS
A4
A5
A6
A7
A8
A9
A10
A11
Figure 3. Z80180 68-Pin PLCC Configuration
PS014004-1106
Overview
Z80180
Microprocessor Unit
RFSH
N/C
N/C
HALT
TEND1
DREQ1
CKS
RXS/CTS1
TXS
CKA1/TEND0
RXA1
TEST
TXA1
N/C
CKA0/DREQ0
RXA0
TXA0
DCD0
CTS0
RTS0
D7
N/C
N/C
D6
5
64
60
55
50
45
41
65
IORQ
MREQ
E
M1
WR
RD
PHI
VSS
VSS
XTAL
N/C
EXTAL
WAIT
BUSACK
BUSREQ
RESET
40
Z80180
80-Pin QFP
5
10
15
20
24
NMI
N/C
N/C
INT0
INT1
INT2
ST
A0
A1
A2
A3
VSS
A4
N/C
A5
A6
A7
A8
A9
A10
A11
N/C
N/C
A12
1
D5
D4
D3
D2
D1
D0
VSS
A19
VCC
A18/TOUT
NC
A17
A16
A15
A14
A13
Figure 4. Z80180 80-Pin QFP Configuration
Table 2. Pin Status During RESET BUSACK and SLEEP
Pin Number and
Package Type
QFP
PLCC
DIP
Default
Function
1
9
8
NMI
2
PS014004-1106
Pin Status
Secondary
Function
RESET BUSACK
IN
IN
SLEEP
IN
NC
Overview
Z80180
Microprocessor Unit
6
Table 2. Pin Status During RESET BUSACK and SLEEP(continued) (continued)
Pin Number and
Package Type
QFP
PLCC
DIP
3
Default
Function
Pin Status
Secondary
Function
RESET BUSACK
SLEEP
NC
4
10
9
INT0
IN
IN
IN
5
11
10
INT1
IN
IN
IN
6
12
11
INT2
IN
IN
IN
7
13
12
ST
1
?
1
8
14
13
A0
3T
3T
1
9
15
14
A1
3T
3T
1
10
16
15
A2
3T
3T
1
11
17
16
A3
3T
3T
1
12
18
VSS
GND
GND
GND
13
19
A4
3T
3T
1
17
14
NC
15
20
18
A5
3T
3T
1
16
21
19
A6
3T
3T
1
17
22
20
A7
3T
3T
1
18
23
21
A8
3T
3T
1
19
24
22
A9
3T
3T
1
20
25
23
A10
3T
3T
1
21
26
24
A11
3T
3T
1
22
NC
23
NC
24
27
25
A12
3T
3T
1
25
28
26
A13
3T
3T
1
26
29
27
A14
3T
3T
1
27
30
28
A15
3T
3T
1
28
31
29
A16
3T
3T
1
29
32
30
A17
3T
3T
1
3T
3T
1
30
31
NC
33
PS014004-1106
31
A18
TOUT
Overview
Z80180
Microprocessor Unit
7
Table 2. Pin Status During RESET BUSACK and SLEEP(continued) (continued)
Pin Number and
Package Type
Pin Status
Secondary
Function
RESET BUSACK
QFP
PLCC
DIP
Default
Function
32
34
32
VCC
VCC
VCC
VCC
33
35
A19
3T
3T
1
34
36
33
VSS
GND
GND
GND
35
37
34
D0
3T
3T
3T
36
38
35
D1
3T
3T
3T
37
39
36
D2
3T
3T
3T
38
40
37
D3
3T
3T
3T
39
41
38
D4
3T
3T
3T
40
42
39
D5
3T
3T
3T
41
43
40
D6
3T
3T
3T
42
NC
43
NC
SLEEP
44
44
41
D7
3T
3T
3T
45
45
42
RTS0
1
OUT
1
46
46
43
CTS0
IN
OUT
IN
47
47
44
DCD0
IN
IN
IN
48
48
45
TXA0
1
OUT
OUT
49
49
46
RXA0
IN
IN
IN
50
50
47
CKA0
3T
OUT
OUT
1
OUT
OUT
IN
IN
IN
3T
IN
IN
1
OUT
OUT
IN
IN
IN
51
DREQ0
NC
52
51
53
52
54
53
49
RXA1
55
54
50
CKA1
56
55
51
TXS
57
56
52
RXS
58
57
53
CKS
3T
I/O
I/O
59
58
54
DREQ1
IN
3T
IN
60
59
55
TEND1
1
OUT
1
PS014004-1106
48
TXA1
TEST
TEND0
CTS1
Overview
Z80180
Microprocessor Unit
8
Table 2. Pin Status During RESET BUSACK and SLEEP(continued) (continued)
Pin Number and
Package Type
QFP
PLCC
DIP
Default
Function
61
60
56
HALT
62
NC
63
NC
Pin Status
Secondary
Function
RESET BUSACK
SLEEP
1
1
0
64
61
57
RFSH
1
OUT
OUT
65
62
58
IORQ
1
3T
1
66
63
59
MREQ
1
3T
1
67
64
60
E
0
OUT
OUT
68
65
61
M1
1
1
1
69
66
62
WR
1
3T
1
70
67
63
RD
1
3T
1
71
68
64
PHI
OUT
OUT
OUT
72
1
1
VSS
GND
GND
GND
73
2
VSS
GND
GND
GND
74
3
XTAL
OUT
OUT
OUT
2
75
NC
76
4
3
EXTAL
IN
IN
IN
77
5
4
WAIT
IN
IN
IN
78
6
5
BUSACK
1
OUT
OUT
79
7
6
BUSREQ
IN
IN
IN
80
8
7
RESET
IN
IN
IN
Pin Descriptions
A0–A19. Address Bus (output, active High, 3-state)—A0–A19 form a 20-bit address bus.
The address bus provides the address for memory data bus exchanges, up to 1 MB, and I/O
data bus exchanges, up to 64 KB. The address bus enters a high-impedance state during reset
and external bus acknowledge cycles. Address line A18 is multiplexed with the output of
programmable reload timer (PRT) channel 1 (TOUT, selected as address output on reset) and
address line A19 is not available in DIP versions of the Z80180.
PS014004-1106
Overview
Z80180
Microprocessor Unit
9
BUSACK—Bus Acknowledge (output, active Low). BUSACK indicates the requesting
device, the MPU address and data bus, and some control signals that enter their high-impedance state.
BUSREQ—Bus Request (input, active Low). This input is used by
external devices (such as DMA controllers) to request access to the
system bus. This request demands a higher priority than NMI and is always recognized at the
end of the current machine cycle. This signal stops the CPU from executing further instructions and places address and data buses, and other control signals, into the high-impedance
state.
CKA0, CKA1—Asynchronous Clock 0 and 1 (bidirectional, active High). When in output
mode, these pins are the transmit and receive clock
outputs from the ASCI baud rate generators. When in input mode, these pins serve as the
external clock inputs for the ASCI baud rate generators. CKA0 is multiplexed with DREQ0,
and CKA1 is multiplexed with TEND0.
CKS—Serial Clock (bidirectional, active High). This line is the clock for the CSIO channel.
CLOCK—System Clock (output, active High). The output is used as a
reference clock for the MPU and the external system. The
frequency of this output is equal to one-half that of the crystal or input clock frequency.
CTS0–CTS1—Clear to send 0 and 1 (inputs, active Low). These lines are modem control
signals for the ASCI channels. CTS1 is
multiplexed with RXS.
D0–D7—Data Bus (bidirectional, active High, 3-state). D0–D7
constitute an 8-bit bidirectional data bus, used for the transfer of
information to and from I/O and memory devices. The data bus enters the high-impedance
state during reset and external bus acknowledge cycles.
DCD0—Data Carrier Detect 0 (input, active Low). A programmable modem control signal
for ASCI channel 0.
DREQ0, DREQ1. DMA Request 0 and 1 (input, active Low). DREQ is used to request a
DMA transfer from one of the on-chip DMA channels. The DMA channels monitor these
inputs to determine when an external device is ready for a READ or WRITE operation. These
inputs can be programmed to be either level or edge sensed. DREQ0 is multiplexed with
CKA0.
E—Enable Clock (output, active High). Synchronous machine cycle clock output during bus
transactions.
EXTAL—External Clock Crystal (input, active High). Crystal oscillator connections. An
external clock can be input to the Z80180 on this pin when a crystal is not used. This input is
Schmitt-triggered.
HALT—HALT/SLEEP (output, active Low). This output is asserted after the CPU executes
either the HALT or SLEEP instruction, and is waiting for either nonmaskable or maskable
PS014004-1106
Overview
Z80180
Microprocessor Unit
10
interrupt before operation resumes. It is also used with the M1 and ST signals to decode
status of the CPU machine cycle.
INT0—Maskable Interrupt Request 0 (input, active Low). This signal is generated by external I/O devices. The CPU honors these requests at the end of the current instruction cycle as
long as the NMI and BUSREQ
signals are inactive. The CPU acknowledges this interrupt request with an interrupt
acknowledge cycle. During this cycle, both the M1 and IORQ signals become active.
INT1, INT2—Maskable Interrupt Request 1 and 2 (inputs, active Low). This signal is generated by external I/O devices. The CPU honors these requests at the end of the current
instruction cycle as long as the NMI, BUSREQ, and INT0 signals are inactive. The CPU
acknowledges these requests with an interrupt acknowledge cycle. Unlike the acknowledgment for INT0, during this cycle neither the M1 or IORQ signals become active.
IORQ—I/O Request (output, active Low, 3-state). IORQ indicates that the address bus contains a valid I/O address for an I/O READ or I/O WRITE operation. IORQ is also generated,
along with M1, during the acknowledgment of the INT0 input signal to indicate that an interrupt response vector can be placed onto the data bus. This signal is analogous to the IOE sig-
nal of the Z64180.
M1—Machine Cycle 1 (output, active Low). Together with MREQ, M1 indicates that the current cycle is the opcode fetch cycle of and instruction execution. Together with IORQ, M1
indicates that the current cycle is for an interrupt acknowledge. It is also used with the HALT
and ST signal to decode status of the CPU machine cycle. This signal is analogous to the LIR
signal of the Z64180.
MREQ—Memory Request (output, active Low, 3-state). MREQ indicates that the address
bus holds a valid address for a memory READ or memory WRITE operation. This signal is
analogous to the ME signal of Z64180.
NMI—Nonmaskable Interrupt (input, negative edge triggered). NMI demands a higher priority than INT and is always recognized at the end of an instruction, regardless of the state of
the interrupt enable flip-flops. This signal forces CPU execution to continue at location
0066h.
RD—Opcode Reinitialized (output, active Low, 3-state). RD indicated that the CPU wants to
read data from memory or an I/O device. The addressed I/O or memory device must use this
signal to gate data onto the CPU data bus.
RFSH—Refresh (output, active Low). Together with MREQ, RFSH indicates that the current
CPU machine cycle and the contents of the address bus must be used for refresh of dynamic
memories. The low order 8 bits of the address bus (A7–A10) contain the refresh address.
This signal is analogous to the REF signal of the Z64180.
RTS0—Request to Send 0 (output, active Low). A programmable modem control signal for
ASCI channel 0.
RXA0, RXA1—Receive Data 0 and 1 (input, active High). These signals are the receive data
to the ASCI channels.
PS014004-1106
Overview
Z80180
Microprocessor Unit
11
RXS—Clocked Serial Receive Data (input, active High). This line is the receiver data for the
CSIO channel. RXS is multiplexed with the CTS1 signal for ASCI channel 1.
ST—Status (output, active High). This signal is used with the M1 and HALT output to
decode the status of the CPU machine cycle.
Table 3. Status Summary
ST
0
1
HALT
1
1
M1
0
0
1
0
0
1
1
X
0
0
1
1
0
1
Operation
CPU Operation (1st opcode fetch)
CPU Operation (2nd opcode and 3rd opcode
fetch)
CPU Operation (MC except for opcode fetch)
DMA Operation
HALT Mode
SLEEP Mode (including SYSTEM STOP
Mode)
Notes:
X = Reserved.
MC = Machine Cycle.
TEND0, TEND1—Transfer End 0 and 1 (outputs, active Low). This output is asserted active
during the most recent WRITE cycle of a DMA
operation. It is used to indicate the end of the block transfer. TEND0 is multiplexed with
CKA1.
TEST—Test (output, not in DIP version). This pin is for test and must be left open.
TOUT—Timer Out (output, active High). TOUT is the pulse output from PRT channel 1. This
line is multiplexed with A18 of the address bus.
TXA0, TXA1—Transmit Data 0 and 1 (outputs, active High). These signals are the transmitted data from the ASCI channels. Transmitted data changes are with respect to the falling
edge of the transmit clock.
TXS—Clocked Serial Transmit Data (output, active High). This line is the transmitted data
from the CSIO channel.
WAIT—Wait (input, active Low). WAIT indicated to the MPU that the addressed memory or
I/O devices are not ready for a data transfer. This input is sampled on the falling edge of T2
(and subsequent wait states). If the input is sampled Low, then the additional wait states are
inserted until the WAIT input is sampled high, at which time execution continues.
WR—WRITE (output, active Low, 3-state). WR indicated that the CPU data bus holds valid
data to be stored at the addressed I/O or memory location.
XTAL—Crystal (input, active High). Crystal oscillator connection. This pin must be left
open if an external clock is used instead of a crystal. The oscillator input is not a TTL level
PS014004-1106
Overview
Z80180
Microprocessor Unit
12
(see DC Characteristics on page 21). Several pins are used for different conditions,
depending on the circumstance.
Multiplexed Pin Descriptions
Table 4. Multiplexed Pin Descriptions
Pin
Description
A18/TOUT
During RESET, this pin is initialized as A18 pin. If either TOC1 or TOC0
bit of the Timer Control Register (TCR) is set to 1, TOUT function is
selected. If TOC1 and TOC0 are cleared to 0, A18 function is selected.
CKA0/DREQ0
During RESET, this pin is initialized as CKA0 pin. If either DM1 or SM1
in DMA Mode Register (DMODE) is set to 1, DREQ0 function is always
selected.
CKA1/TEND0
During RESET, this pin is initialized as CKA1 pin. If CKA1D bit in ASCI
control register ch1 (CNTLA1) is set to 1, TEND0 function is selected. If
CKA1D bit is set to 0, CKA1 function is selected.
RXS/CTS1
During RESET, this pin is initialized as RXS pin. If CTS1E bit in ASCI
status register ch1 (STAT1) is set to 1, CTS1 function is selected. If
CTS1E bit is set to 0, RXS function is selected.
PS014004-1106
Overview
Z80180
Microprocessor Unit
13
Architecture
The Z180® combines a high-performance CPU core with a variety of
system and I/O resources useful in a broad range of applications. The CPU core consists of
five functional blocks: clock generator, bus state controller, interrupt controller, memory
management unit (MMU), and the central processing unit (CPU). The integrated I/O
resources make up the remaining four function blocks: direct memory access (DMA) control
(2 channels), asynchronous serial communication interface (ASCI) 2 channels, programmable reload timers (PRT) 2 channels, and a clock serial I/O (CSIO) channel.
Clock Generator—Generates system clock from an external crystal or clock input. The
external clock is divided by two or one and provided to both internal and external devices.
Bus State Controller—This logic performs all of the status and bus control activity
associated with both the CPU and some on-chip peripherals. Included are wait-state timing,
reset cycles, DRAM refresh, and DMA bus exchanges.
Interrupt Controller—This logic monitors and prioritizes the variety of internal and
external interrupts and traps to provide the correct responses from the CPU. To maintain
compatibility with the Z80® CPU, three different interrupts modes are supported.
Memory Management Unit—The MMU allows you to map the memory used by the CPU
(logically only 64 KB) into the 1-MB addressing range supported by the Z80180. The organization of the MMU object code allows maintenance compatibility with the Z80 CPU,
while offering access to an extended memory space. This organization is achieved by using
an effective common area-banked area scheme.
Central Processing Unit—The CPU is microcoded to provide a core that is object-code
compatible with the Z80 CPU. It also provides a superset of the Z80 instruction set, including 8-bit multiply. The core is modified to allow many of the instructions to execute in fewer
clock cycles.
DMA Controller—The DMA controller provides high speed transfers between memory and
I/O devices. Transfer operations supported are memory-to-memory, memory to/from I/O,
and I/O-to-I/O. Transfer modes supported are request, burst, and cycle steal. DMA transfers
can access the full 1 MB address range with a block length up to 64 KB, and can cross over
64K boundaries.
Asynchronous Serial Communication Interface (ASC)—The ASCI logic provides two
individual full-duplex UARTs. Each channel includes a programmable baud rate generator
and modem control signals. The ASCI channels also support a multiprocessor
communication format as well as break detection and generation.
Programmable Reload Timers (PRT)—This logic consists of two separate channels, each
containing a 16-bit counter (timer) and count reload register. The time base for the counters
is derived from the system clock (divided by 20) before reaching the counter. PRT channel 1
provides an optional output to allow for waveform generation.
PS014004-1106
Architecture
Z80180
Microprocessor Unit
14
Timer Data Register
WRITE (0004h)
RESET
Timer Data
Register
FFFFh
0004h
0 < t < 20 f
20 f
20 f
0003h
0002h
20 f
20 f
20 f
20 f
20 f
20 f
20 f
0001h
0000h
0003h
0002h
0001h
0000h
0003h
Timer Reload Register WRITE (0003h)
Timer Reload
Register
FFFFh
Reload
Reload
0003h
WRITE a 1 to TDE
TDE Flag
TIF Flag
Timer Data Register READ
Timer Control Requestor READ
Figure 5. Timer Initialization, Count Down, and Reload Timing
f
Timer Data
Reg. = 0001h
Timer Data
Reg. = 0000h
TOUT
Figure 6. Timer Data Register
Clocked Serial I/O (CSIO). The CSIO channel provides a half-duplex serial transmitter and
receiver. This channel can be used for simple high-speed data connection to another microprocessor or microcomputer. TRDR is used for both CSIO transmission and reception. The
system design must ensure that the constraints of half-duplex operation are met. Transmit
and Receive operations cannot occur simultaneously. For example, if a CSIO transmission is
attempted while the CSIO is receiving data, a CSIO does not work.
Note: TRDR is not buffered. Attempting to perform a CSIO transmit while the previous
transmit data is still being shifted out causes the shift data to be immediately
PS014004-1106
Architecture
Z80180
Microprocessor Unit
15
updated, corrupting the transmit operation in progress. Reading TRDR while a
transmit or receive is in progress must be avoided.
Internal Address/Data Bus
φ
TXS
RXS
CSIO Transmit/Receive
Data Register:
TRDR (8)
Baud Rate
Generator
CKS
CSIO Control Register:
CNTR (8)
Interrupt Request
Figure 7. CSIO Block Diagram
Operation Modes
Z80® versus 64180 Compatibility
The Z80180 is descended from two different ancestor processors, ZiLOG's original Z80 and
the Hitachi 64180. The Operating Mode
Control Register (OMCR), illustrated in Figure 8, can be programmed to select between
certain Z80 and 64180 differences.
.
D7 D6 D5 — — — — —
Reserved
IOC (R/W)
M1TE (W)
M1E (R/W)
Figure 8. Operating Control Register (OMCR: I/O Address = 3Eh)
M1E (M1 Enable)—This bit controls the M1 output and is set to a 1
during RESET.
When M1E = 1, the M1 output is asserted Low during the opcode fetch cycle, the INT0
acknowledge cycle, and the first machine cycle of the NMI acknowledge.
PS014004-1106
Architecture
Z80180
Microprocessor Unit
16
On the Z80180, this choice makes the processor fetch a RETI instruction one time only, and
when fetching a RETI from zero-wait-state memory uses three clock machine cycles, which
are not fully Z80-timing compatible but are compatible with the on-chip CTCs.
When M1E = 0, the processor does not drive M1 Low during instruction fetch cycles. After
fetching a RETI instruction one time only, with normal timing, the processor goes back and
refetches the instruction using fully Z80-compatible cycles that include driving M1 Low.
Some external Z80 peripherals may require properly decoded RETI instructions. Figure 9
illustrates the RETI sequence when M1E = 0.
T1
T2
T3
T1
T2
T3
TI
TI
TI
T1
T2
T3
TI
T1
T2
T3
TI
φ
A0–A18 (A19)
D0–D7
PC+1
PC
EDh
4Dh
PC
EDh
PC+1
4Dh
M1
MREQ
RD
ST
Figure 9. RETI Instruction Sequence with MIE = 0
M1TE (M1 Temporary Enable)—This bit controls the temporary
assertion of the M1 signal. It is always read back as a 1 and is set to 1 during RESET.
When M1E is set to 0 to accommodate certain external Z80 peripheral(s), those same
device(s) may require a pulse on M1 after programming certain of their registers to complete
the function being programmed.
For example, when a control word is written to the Z80 PIO to enable interrupts, no enable
actually takes place until the PIO identifies an active M1 signal. When M1TE = 1, there is no
change in the operation of the M1
signal and M1E controls its function. When M1TE = 0, the M1 output is asserted during the
next opcode fetch cycle regardless of the state
programmed into the M1E bit. This instance is only momentary (one time only) and you are
not required to preprogram a 1 to disable the function (see Figure 10).
PS014004-1106
Architecture
Z80180
Microprocessor Unit
17
T1
T2
T3
T1
T2
T3
f
WR
M1
WRITE into OMCR
Opcode Fetch
Figure 10. M1 Temporary Enable Timing
IOC—This bit controls the timing of the IORQ and RD signals. It is set to 1 by RESET. When
IOC = 1, the IORQ and RD signals function the same as the Z64180 (Figure 11).
T1
T2
TW
T3
φ
IORQ
RD
WR
Figure 11. I/O READ and WRITE Cycles with IOC = 1
When IOC = 0, the timing of the IORQ and RD signals match the timing of the Z80. The
IORQ and RD signals go active as a result of the rising edge of T2 (see Figure 12).
T1
T2
TW
T3
φ
IORQ
RD
WR
Figure 12. I/O READ and WRITE Cycles with IOC = 0
PS014004-1106
Architecture
Z80180
Microprocessor Unit
18
HALT and Low-Power Operating Modes—The Z80180 can operate in five modes with
respect to activity and power consumption:
•
•
•
•
•
Normal Operation
HALT mode
IOSTOP mode
SLEEP mode
SYSTEM STOP mode
Normal Operation—The Z80180 processor is fetching and running a program. All enabled
functions and portions of the device are active, and the HALT pin is High.
HALT Mode—This mode is entered by the HALT instruction. Thereafter, the Z80180
processor continually fetches the following opcode but does not execute it, and drives the
HALT, ST and M1 pins all Low. The oscillator and PHI pin remain active, interrupts and bus
granting to external masters, and DRAM refresh can occur and all on-chip I/O devices
continue to operate including the DMA channels.
The Z80180 leaves HALT mode in response to a Low on RESET, on to an interrupt from an
enabled on-chip source, an external request on NMI, or an enabled external request on INT0,
INT1, or INT2. In case of an interrupt, the return address is the instruction following the
HALT instruction; at that point the program can either branch back to the HALT instruction
to wait for another interrupt, or can examine the new state of the system/application and
respond appropriately.
T2
T3
Interrupt
Acknowledge Cycle
HALT Mode
HALT Opcode Fetch Cycle
T1
T2
T3
T1
T2
φ
INTi, NMI
A0–A19
HALT Opcode Address
HALT Opcode Address + 1
HALT
M1
MREQ
RD
Figure 13. HALT Timing
PS014004-1106
Architecture
Z80180
Microprocessor Unit
19
SLEEP Mode—Enter SLEEP mode by keeping the IOSTOP bit (ICR5) bits 3 and 6 of the
CPU Control Register (CCR3, CCR6) all zero and executing the SLEEP instruction. The
oscillator and PHI output continue operating, but are blocked from the CPU core and DMA
channels to reduce power consumption. DRAM refresh stops but interrupts and
granting to external master can occur. Except when the bus is granted to an external master,
A19–0 and all control signals except HALT are maintained High. HALT is Low. I/O operations continue as before the SLEEP instruction, except for the DMA channels.
The Z80180 leaves SLEEP mode in response to a Low on RESET, an
interrupt request from an on-chip source, an external request on NMI, or an external request
on INT0, INT1, or INT2.
If an interrupt source is individually disabled, it cannot bring the Z80180 out of SLEEP
mode. If an interrupt source is individually enabled, and the IEF bit is 1 so that interrupts are
globally enabled (by an EI instruction), the highest priority active interrupt occurs, with the
return address being the instruction after the SLEEP instruction. If an interrupt source is individually enabled, but the IEF bit is 0 so that interrupts are globally disabled (by a DI instruction), the Z80180 leaves SLEEP mode by simply executing the following instruction(s).
This provides a technique for synchronization with high- speed external events without
incurring the latency imposed by an interrupt response sequence. Figure 14 displays the
timing for exiting SLEEP mode due to an interrupt request.
Note:
The Z80180 takes about 1.5 clocks to restart.
SLEEP 2nd Opcode
Fetch Cycle
T2
T3
Opcode Fetch or Interrupt
Acknowledge Cycle
SLEEP Mode
T1
T2
TS
TS
T1
T2
T3
φ
INTi, NMI
A0–A19
SLEEP 2nd Opcode Address
FFFFFh
HALT
M1
Figure 14. SLEEP Timing
IOSTOP Mode—IOSTOP mode is entered by setting the IOSTOP bit of the I/O Control
Register (ICR) to 1. In this case, on-chip I/O (ASCI, CSIO, PRT) stops operating. However,
the CPU continues to operate. Recovery from IOSTOP mode is by resetting the IOSTOP bit
in ICR to 0.
SYSTEM STOP Mode—SYSTEM STOP mode is the combination of SLEEP and IOSTOP
modes. SYSTEM STOP mode is entered by setting the IOSTOP bit in ICR to 1 followed by
PS014004-1106
Architecture
Z80180
Microprocessor Unit
20
execution of the SLEEP instruction. In this mode, on-chip I/O and CPU stop operating,
reducing power consumption, but the PHI output continues to operate. Recovery from SYSTEM STOP mode is the same as recovery from SLEEP mode except that internal I/O sources
(disabled by IOSTOP) cannot generate a recovery interrupt.
Standard Test Conditions
The DC Characteristics section applies to the following standard test
conditions, unless otherwise noted. All voltages are referenced to
GND (0 V). Positive current flows in to the referenced pin.
All AC parameters assume a load capacitance of 100 pF. Add 10 ns delay for each 50 pF
increase in load up to a maximum of 200 pF for the data bus and 100 pF for the address and
control lines. AC timing measurements are referenced to 1.5 volts (except for CLOCK,
which is referenced to the 10% and 90% points). The Ordering Information section lists
temperature ranges and product numbers. Package drawings are in the
Package Information section (see Figure 15).
+5 V
2.1k
From Output
Under Test
250
µA
100 pF
Figure 15. AC Load Capacitance Parameters
Absolute Maximum Ratings
Permanent LSI damage occurs if maximum ratings listed in Table 5 are exceeded.
Table 5. Absolute Maximum Ratings
PS014004-1106
Item
Symbol
Value
Unit
Supply Voltage
VCC
–0.3 ~ +7.0
V
Input Voltage
VIN
–0.3 ~ VCC +0.3
V
Operating Temperature
Topr
0 ~ 70
°C
Architecture
Z80180
Microprocessor Unit
21
Table 5. Absolute Maximum Ratings(continued)
Item
Symbol
Value
Unit
Extended Temperature
Text
–40 ~ 85
°C
Storage Temperature
Tstg
–55 ~ +150
°C
Note: Normal operation must be under recommended operating conditions. If these
conditions are exceeded, it affects reliability of LSI.
DC Characteristics
Table 6 lists the DC characteristics of Z80180™ MPU.
Table 6. DC Characteristics
Symbol Item
VIH1
Input H Voltage
RESET, EXTAL, NMI
Input H Voltage Except
VIH2
RESET, EXTAL, NMI
VIL1
Input L Voltage RESET,
EXTAL, NMI
VIL2
Input L Voltage Except
RESET, EXTAL, NMI
Outputs H Voltage All
VOH
outputs
VOL
IIL
ITL
ICC*
Outputs L Voltage All
outputs
Input Leakage Current
All Inputs Except XTAL,
EXTAL
Three State Leakage
Current
Power Dissipation*
(Normal Operation)
Condition
IOH = –200 µA
IOH = –20 µA
IOL = –2.2 mA
Unit
V
–0.3
0.8
V
–
–
0.45
V
–
1.0
µA
–
–
1.0
µA
–
–
–
–
–
–
15
20
25
3.8
5
6.3
40
50
60
12.5
15
17.5
mA
–
2.4
–
VCC –1.2 –
–
–
VIN = 0.5 ~ VCC –
–0.5
VIN = 0.5 ~ VCC
–0.5
F = 6 MHz
F = 8 MHz
F = 10 MHz**
Power Dissipation*
F = 6 MHz
(SYSTEM STOP mode) F = 8 MHz
F = 10 MHz**
PS014004-1106
Min
Typ Max
VCC –0.6 –
VCC
+0.3
2.0
–
VCC
+0.3
–0.3
–
0.6
V
V
V
Architecture
Z80180
Microprocessor Unit
22
Table 6. DC Characteristics (continued)
Symbol Item
CP
Pin Capacitance
Condition
Min
VINVin = 0V, φ = –
1 MHz TA = 25°
C
Typ Max
–
12
Unit
pF
Note: *VIHmin = VCC –1.0 V, VILmax = 0.8 V (all output terminals are at no load); VCC = 5.0 V.
**VCC = 5 V + 10%, VSS = 0 V over specified temperature range, unless otherwise noted
AC Characteristics
Table 7, Table 8, and Table 9 provide AC characteristics for the
Z80180-6, Z80180-8, and Z80180-10, respectively.
VCC = 5 V + 10%,
VSS = 0 V, TA – 0 °C to +70 °C, unless otherwise noted.
Table 7. Z80180-6 AC Characteristics
Z80180-6
No
1
2
3
4
5
6
7
8
9
Symbol
tcyc
tCHW
tCLW
tcf
tcr
tAD
tAS
tMED1
tRDD1
10
11
tM1D1
tAH
12
13
14
15
16
17
18
19
tMED2
tRDD2
tM1D2
tDRS
tDRH
tSTD1
tSTD2
tWS
Item
Clock Cycle Time
Clock H Pulse Width
Clock L Pulse Width
Clock Fall Time
Clock Rise Time
ØRise to Address Valid Delay
Address Valid to MREQ Fall or IORQ Fall)
Ø Fall to MREQ Fall Delay
Ø Fall to RD Fall Delay IOC = 1
Ø Rise to RD Rise Delay IOC = 0
Ø Rise to M1 Fall Delay
Address Hold Time from
(MREQ, IOREQ, RD, WR)
Ø Fall to MREQ Rise Delay
Ø Fall to RD Rise Delay
Ø Rise to M1 Rise Delay
Data Read Set-up Time
Data Read Hold Time
Ø Fall to ST Fall Delay
Ø Fall to ST Rise Delay
WAIT Set-up Time to Ø Fall
PS014004-1106
Min
162
65
65
–
–
–
30
–
–
–
–
35
Max
2000
–
–
15
15
90
–
60
60
65
80
–
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
–
–
–
40
0
–
–
40
60
60
80
–
–
90
90
–
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Architecture
Z80180
Microprocessor Unit
23
Table 7. Z80180-6 AC Characteristics (continued)
Z80180-6
No
20
21
22
23
24
25
26
26a
27
28
Symbol
tWH
tWDZ
tWRD1
tWDD
tWDS
tWRD2
tWRP
tWDH
tIOD1
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
tIOD2
tIOD3
tINTS
tINTS
tNMIW
tBRS
tBRH
tBAD1
tBAD2
tBZD
tMEWH
tMEWL
tRFD1
tRFD2
tHAD1
tHAD2
tDRQS
tDRQH
tTED1
tTED2
tED1
tED2
PWEH
PWEL
tEr
tEf
Item
WAIT Hold Time from Ø Fall
Ø Rise to Data Float Delay
Ø Rise to WR Fall Delay
Ø Fall to WRITE Data Delay Time
WRITE Data Set-up Time to WR Fall
Ø Fall to WR Rise Delay
WR Pulse Width
WR Pulse Width (I/O WRITE Cycle)
WRITE Data Hold Time from (WR Rise)
Ø Fall to IORQ Fall Delay IOC = 1
Ø Rise to IORQ Fall Delay IOC = 1
Ø Fall to IORQ Rise Delay
M1 Fall to IORQ Fall Delay
INT Set-up Time to Ø Fall
INT Hold Time from Ø Fall
NMI Pulse Width
BUSREQ Set-up Time to Ø Fall
BUSREQ Hold Time from Ø Fall
Ø Rise to BUSACK Fall Delay
Ø Fall to BUSACK Rise Delay
Ø Rise to Bus Floating Delay Time
MREQ Pulse Width (High)
MREQ Pulse Width (Low)
Ø Rise to RFSH Fall Delay
Ø Rise to RFSH Rise Delay
Ø Rise to HALT Fall Delay
Ø Rise to HALT Rise Delay
/DREQi Set-up Time to Ø Rise
/DREQi Hold Time from Ø Rise
Ø Fall to TENDi Fall Delay
Ø Fall to TENDi Rise Delay
Ø Rise to E Rise Delay
Ø Fall or Rise to E Fall Delay
E Pulse Width (High)
E Pulse Width (Low)
Enable Rise Time
Enable Fall Time
PS014004-1106
Min
40
–
–
–
40
–
170
332
40
–
–
–
340
40
40
120
40
40
–
–
–
110
125
–
–
–
–
40
40
–
–
–
–
75
180
–
–
Max
–
95
65
90
–
80
–
–
–
60
65
60
–
–
–
–
–
–
95
90
125
–
–
90
90
90
90
–
–
70
70
95
95
–
–
20
20
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Architecture
Z80180
Microprocessor Unit
24
Table 7. Z80180-6 AC Characteristics (continued)
Z80180-6
No
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
Symbol Item
tTOD
Ø Fall to Timer Output Delay
tSTDI
CSIO Transmit Data Delay Time (Internal Clock
Operation)
tSTDE CSIO Transmit Data Delay Time (External Clock
Operation)
tSRSI
CSIO Receive Data Set-up Time (Internal Clock
Operation)
tSRHI
CSIO Receive Data Hold Time (Internal Clock
Operation)
tSRSE CSIO Receive Data Set-up Time (External Clock
Operation)
tSRHE CSIO Receive Data Hold Time (External Clock
Operation)
tRES
RESET Set-up Time to Ø Fall
tREH
RESET Hold Time from Ø Fall
tOSC
Oscillator Stabilization Time
tEXr
External Clock Rise Time (EXTAL)
tEXf
External Clock Fall Time (EXTAL)
tRr
RESET Rise Time
tRf
RESET Fall Time
tIr
Input Rise Time (except EXTAL, RESET)
tIf
Input Fall Time (except EXTAL, RESET)
Min
–
–
Max
300
200
Unit
ns
ns
–
1
7.5tcyc ns
+300
–
tcyc
1
–
tcyc
1
–
tcyc
1
–
tcyc
120
80
–
–
–
–
–
–
–
–
–
20
25
25
50
50
100
100
ns
ns
ns
ns
ns
ns
ns
ns
ns
Table 8. Z80180-8 AC Characteristics
Z80180-8
No
Symbol Item
Min
Max
Unit
1
tcyc
Clock Cycle Time
125
2000
ns
2
tCHW
Clock H Pulse Width
50
–
ns
3
tCLW
Clock L Pulse Width
50
–
ns
4
tcf
Clock Fall Time
–
15
ns
5
tcr
Clock Rise Time
–
15
ns
6
tAD
ØRise to Address Valid Delay
–
80
ns
7
tAS
Address Valid to MREQ Fall or IORQ Fall)
20
–
ns
PS014004-1106
Architecture
Z80180
Microprocessor Unit
25
Table 8. Z80180-8 AC Characteristics (continued)
Z80180-8
No
Symbol Item
Min
Max
Unit
8
tMED1
Ø Fall to MREQ Fall Delay
–
50
ns
9
tRDD1
Ø Fall to RD Fall Delay
–
50
ns
–
60
IOC = 1
Ø Rise to RD Rise Delay
IOC = 0
10
tM1D1
Ø Rise to M1 Fall Delay
–
70
ns
11
tAH
Address Hold Time from
(MREQ, IOREQ, RD, WR)
20
–
ns
12
tMED2
Ø Fall to MREQ Rise Delay
–
50
ns
13
tRDD2
Ø Fall to RD Rise Delay
–
50
ns
14
tM1D2
Ø Rise to M1 Rise Delay
–
70*
ns
15
tDRS
Data Read Set-up Time
30
–
ns
16
tDRH
Data Read Hold Time
0
–
ns
17
tSTD1
Ø Fall to ST Fall Delay
–
70
ns
18
tSTD2
Ø Fall to ST Rise Delay
–
70
ns
19
tWS
WAIT Set-up Time to Ø Fall
40
–
ns
20
tWH
WAIT Hold Time from Ø Fall
40
–
ns
21
tWDZ
Ø Rise to Data Float Delay
–
70
ns
22
tWRD1
Ø Rise to WR Fall Delay
–
60
ns
23
tWDD
Ø Fall to WRITE Data Delay Time
–
80
ns
24
tWDS
WRITE Data Set-up Time to WR Fall
20
–
ns
25
tWRD2
Ø Fall to WR Rise Delay
–
60
ns
26
tWRP
WR Pulse Width
130
–
ns
WR Pulse Width (I/O WRITE Cycle)
255
–
ns
26a
27
tWDH
WRITE Data Hold Time from (WR Rise)
15
–
28
tIOD1
Ø Fall to IORQ Fall Delay
–
50
–
60
Ø Rise to IORQ Fall Delay
IOC = 1
IOC = 1
ns
29
tIOD2
Ø Fall to IORQ Rise Delay
–
50
ns
30
tIOD3
M1 Fall to IORQ Fall Delay
250
–
ns
31
tINTS
INT Set-up Time to Ø Fall
40
–
ns
PS014004-1106
Architecture
Z80180
Microprocessor Unit
26
Table 8. Z80180-8 AC Characteristics (continued)
Z80180-8
No
Symbol Item
Min
Max
Unit
32
tINTS
INT Hold Time from Ø Fall
40
–
ns
33
tNMIW
NMI Pulse Width
100
–
ns
34
tBRS
BUSREQ Set-up Time to Ø Fall
40
–
ns
35
tBRH
BUSREQ Hold Time from Ø Fall
40
36
tBAD1
Ø Rise to BUSACK Fall Delay
–
70
ns
37
tBAD2
Ø Fall to BUSACK Rise Delay
–
70
ns
38
tBZD
Ø Rise to Bus Floating Delay Time
–
90
ns
39
tMEWH
MREQ Pulse Width (High)
90
–
ns
40
tMEWL
MREQ Pulse Width (Low)
100
–
ns
41
tRFD1
Ø Rise to RFSH Fall Delay
–
80
ns
42
tRFD2
Ø Rise to RFSH Rise Delay
–
80
ns
43
tHAD1
Ø Rise to HALT Fall Delay
–
80
ns
44
tHAD2
Ø Rise to HALT Rise Delay
–
80
ns
45
tDRQS
/DREQi Set-up Time to Ø Rise
40
–
ns
46
tDRQH
/DREQi Hold Time from Ø Rise
40
–
ns
47
tTED1
Ø Fall to TENDi Fall Delay
–
60
ns
48
tTED2
Ø Fall to TENDi Rise Delay
–
60
ns
49
tED1
Ø Rise to E Rise Delay
–
70
ns
50
tED2
Ø Fall or Rise to E Fall Delay
–
70
ns
51
PWEH
E Pulse Width (High)
65
–
ns
52
PWEL
E Pulse Width (Low)
130
–
ns
53
tEr
Enable Rise Time
–
20
ns
54
tEf
Enable Fall Time
–
20
ns
55
tTOD
Ø Fall to Timer Output Delay
–
200
ns
56
tSTDI
CSIO Transmit Data Delay Time (Internal Clock
Operation)
–
200
ns
57
tSTDE
CSIO Transmit Data Delay Time (External Clock
Operation)
–
7.5tcy ns
c
+200
PS014004-1106
ns
Architecture
Z80180
Microprocessor Unit
27
Table 8. Z80180-8 AC Characteristics (continued)
Z80180-8
No
Symbol Item
Min
Max
Unit
58
tSRSI
CSIO Receive Data Set-up Time (Internal Clock
Operation)
1
–
tcyc
59
tSRHI
CSIO Receive Data Hold Time (Internal Clock
Operation)
1
–
tcyc
60
tSRSE
CSIO Receive Data Set-up Time (External Clock
Operation)
1
–
tcyc
61
tSRHE
CSIO Receive Data Hold Time (External Clock
Operation)
1
–
tcyc
62
tRES
RESET Set-up Time to Ø Fall
100
–
ns
63
tREH
RESET Hold Time from Ø Fall
70
–
ns
64
tOSC
Oscillator Stabilization Time
–
20
ns
65
tEXr
External Clock Rise Time (EXTAL)
–
25
ns
66
tEXf
External Clock Fall Time (EXTAL)
–
25
ns
67
tRr
RESET Rise Time
–
50
ns
68
tRf
RESET Fall Time
–
50
ns
69
tIr
Input Rise Time (except EXTAL, RESET)
–
100
ns
70
tIf
Input Fall Time (except EXTAL, RESET)
–
100
ns
Table 9. Z80180-10 AC Characteristics
Z80180-10
No
Symbol Item
Min
Max
Unit
1
tcyc
Clock Cycle Time
100
2000
ns
2
tCHW
Clock H Pulse Width
40
–
ns
3
tCLW
Clock L Pulse Width
40
–
ns
4
tcf
Clock Fall Time
–
10
ns
5
tcr
Clock Rise Time
–
10
ns
6
tAD
ØRise to Address Valid Delay
–
70
ns
7
tAS
Address Valid to MREQ Fall or IORQ Fall)
10
–
ns
PS014004-1106
Architecture
Z80180
Microprocessor Unit
28
Table 9. Z80180-10 AC Characteristics (continued)
Z80180-10
No
Symbol Item
Min
Max
Unit
8
tMED1
Ø Fall to MREQ Fall Delay
–
50
ns
9
tRDD1
Ø Fall to RD Fall Delay
–
50
ns
–
55
IOC = 1
Ø Rise to RD Rise Delay
IOC = 0
10
tM1D1
Ø Rise to M1 Fall Delay
–
60
ns
11
tAH
Address Hold Time from
(MREQ, IOREQ, RD, WR)
10
–
ns
12
tMED2
Ø Fall to MREQ Rise Delay
–
50
ns
13
tRDD2
Ø Fall to RD Rise Delay
–
50
ns
14
tM1D2
Ø Rise to M1 Rise Delay
–
60
ns
15
tDRS
Data Read Set-up Time
25
–
ns
16
tDRH
Data Read Hold Time
0
–
ns
17
tSTD1
Ø Fall to ST Fall Delay
–
60
ns
18
tSTD2
Ø Fall to ST Rise Delay
–
60
ns
19
tWS
WAIT Set-up Time to Ø Fall
30
–
ns
20
tWH
WAIT Hold Time from Ø Fall
30
–
ns
21
tWDZ
Ø Rise to Data Float Delay
–
60
ns
22
tWRD1
Ø Rise to WR Fall Delay
–
50
ns
23
tWDD
Ø Fall to WRITE Data Delay Time
–
60
ns
24
tWDS
WRITE Data Set-up Time to WR Fall
15
–
ns
25
tWRD2
Ø Fall to WR Rise Delay
–
50
ns
26
tWRP
WR Pulse Width
110
–
ns
WR Pulse Width (I/O WRITE Cycle)
210
–
ns
26a
27
tWDH
WRITE Data Hold Time from (WR Rise)
10
–
28
tIOD1
Ø Fall to IORQ Fall Delay
–
50
–
55
Ø Rise to IORQ Fall Delay
IOC = 1
IOC = 1
ns
29
tIOD2
Ø Fall to IORQ Rise Delay
–
50
ns
30
tIOD3
M1 Fall to IORQ Fall Delay
200
–
ns
31
tINTS
INT Set-up Time to Ø Fall
30
–
ns
PS014004-1106
Architecture
Z80180
Microprocessor Unit
29
Table 9. Z80180-10 AC Characteristics (continued)
Z80180-10
No
Symbol Item
Min
Max
Unit
32
tINTS
INT Hold Time from Ø Fall
30
–
ns
33
tNMIW
NMI Pulse Width
80
–
ns
34
tBRS
BUSREQ Set-up Time to Ø Fall
30
–
ns
35
tBRH
BUSREQ Hold Time from Ø Fall
30
36
tBAD1
Ø Rise to BUSACK Fall Delay
–
60
ns
37
tBAD2
Ø Fall to BUSACK Rise Delay
–
60
ns
38
tBZD
Ø Rise to Bus Floating Delay Time
–
80
ns
39
tMEWH
MREQ Pulse Width (High)
70
–
ns
40
tMEWL
MREQ Pulse Width (Low)
80
–
ns
41
tRFD1
Ø Rise to RFSH Fall Delay
–
60
ns
42
tRFD2
Ø Rise to RFSH Rise Delay
–
60
ns
43
tHAD1
Ø Rise to HALT Fall Delay
–
50
ns
44
tHAD2
Ø Rise to HALT Rise Delay
–
50
ns
45
tDRQS
/DREQi Set-up Time to Ø Rise
30
–
ns
46
tDRQH
/DREQi Hold Time from Ø Rise
30
–
ns
47
tTED1
Ø Fall to TENDi Fall Delay
–
50
ns
48
tTED2
Ø Fall to TENDi Rise Delay
–
50
ns
49
tED1
Ø Rise to E Rise Delay
–
60
ns
50
tED2
Ø Fall or Rise to E Fall Delay
–
60
ns
51
PWEH
E Pulse Width (High)
55
–
ns
52
PWEL
E Pulse Width (Low)
110
–
ns
53
tEr
Enable Rise Time
–
20
ns
54
tEf
Enable Fall Time
–
20
ns
55
tTOD
Ø Fall to Timer Output Delay
–
150
ns
56
tSTDI
CSIO Transmit Data Delay Time (Internal Clock
Operation)
–
150
ns
57
tSTDE
CSIO Transmit Data Delay Time (External Clock
Operation)
–
7.5tcy ns
c
+150
PS014004-1106
ns
Architecture
Z80180
Microprocessor Unit
30
Table 9. Z80180-10 AC Characteristics (continued)
Z80180-10
No
Symbol Item
Min
Max
Unit
58
tSRSI
CSIO Receive Data Set-up Time (Internal Clock
Operation)
1
–
tcyc
59
tSRHI
CSIO Receive Data Hold Time (Internal Clock
Operation)
1
–
tcyc
60
tSRSE
CSIO Receive Data Set-up Time (External Clock
Operation)
1
–
tcyc
61
tSRHE
CSIO Receive Data Hold Time (External Clock
Operation)
1
–
tcyc
62
tRES
RESET Set-up Time to Ø Fall
80
–
ns
63
tREH
RESET Hold Time from Ø Fall
50
–
ns
64
tOSC
Oscillator Stabilization Time
–
TBD
ns
65
tEXr
External Clock Rise Time (EXTAL)
–
25
ns
66
tEXf
External Clock Fall Time (EXTAL)
–
25
ns
67
tRr
RESET Rise Time
–
50
ns
68
tRf
RESET Fall Time
–
50
ns
69
tIr
Input Rise Time (except EXTAL, RESET)
–
100
ns
70
tIf
Input Fall Time (except EXTAL, RESET)
–
100
ns
Timing Diagrams
Z80180 Timing signals are displayed in Figure 16 through Figure 27.
PS014004-1106
Architecture
Z80180
Microprocessor Unit
31
I/O Write Cycle*
I/O Read Cycle*
Opcode Fetch Cycle
T1
3
2
T2
4
PHI
TW
T3
T1
T2
TW
T3
T1
5
1
6
ADDRESS
19
WAIT
20
19
20
7
12 11
MREQ
7
8
29 11
IORQ
11
13
28
13
RD
9
11
9
25
22
WR
26
14
M1
18
10
ST
17
15
21
15
16
16
Data IN
23
24
27
Data OUT
62
63
RESET
68
67
62
67
63
68
Figure 16. CPU Timing (Opcode Fetch, I/O WRITE, and I/O READ Cycles)
PS014004-1106
Architecture
Z80180
Microprocessor Unit
32
ø
32
31
INTi
33
NMI
MI *1
30
10
14
28
IORQ *1
29
15
16
Date IN *1
39
MREQ *2
41
42
40
RFSH *2
35
34
34
35
BUSREQ
36
37
BUSACK
38
38
ADDRESS
DATA
MREQ, RD
WR, IORQ
43
*3
44
HALT
Figure 17. CPU Timing (INT0 Acknowledge Cycle, Refresh Cycle)
PS014004-1106
Architecture
Z80180
Microprocessor Unit
33
CPU Timin= 0) (I/O READ Cycle, I/O WRITE Cycle)
I/O WRITE Cycle
I/O READ Cycle
T1
T2
Tw
T3
T1
T2
Tw
T3
φ
ADDRESS
IROQ
RD
28
29
9
13
28
29
22
25
WR
CPU Timing (IOC=0) I/O READ Cycle
I/O WRITE Cycle
Figure 18. CPU Timing (IOC = 0) (I/O READ Cycle, I/O WRITE Cycle)
PS014004-1106
Architecture
Z80180
Microprocessor Unit
34
DMA Control Signals
CPU or DMA READ/WRITE Cycle (Only DMA WRITE Cycle for TENDi)
T1
T2
TW
T3
T1
ø
45
46*1
DREQi
(at level sense)
45
46*2
DREQi
(at level sense)
*4
47
18
48
TENDi
*3 17
ST
Notes:
1. tDRQS and tDHQH are specified for the rising edge of clock followed by T3.
2. tDRQS and tDHQH are specified for the rising edge of clock.
3. DMA cycle starts.
4. CPU cycle starts.
Figure 19. DMA Control Signals
PS014004-1106
Architecture
Z80180
Microprocessor Unit
35
E Clock Timing (Memory READ/WRITE Cycle, I/O READ/WRITE Cycle)
T1
T2
TW
TW
T3
ø
~
~
49
50
~
~
E
(Memory READ/WRITE)
49
50
~
~
E
(I/O READ)
49
50
~
~
E
(I/O WRITE)
15
16
~
~ ~
~
D0–D7
Figure 20. E Clock Timing (Memory R/W Cycle, I/O R/W Cycle)
E
PH1ø
E
BUS RELEASE mode
SLEEP mode
SYSTEM STOP mode
49
50
Figure 21. E Clock Timing (Bus Release, Sleep, System Stop Modes
E Clock Timing (Bus Release, Sleep, System Stop Modes)
E Clock Timing (Minimum timing example of
T2
E
Example
I/O READ
→ Opcode Fetch
TW
T3
T1
50
49
53
50
54
51
52
T2
49
53
54
Figure 22. E Clock Timing (PWEL and PWEH Minimum Timing)
PS014004-1106
Architecture
Z80180
Microprocessor Unit
36
Timer Output Timing
Timer Data
Reg.=0000h
A18/TOUT
55
Figure 23. Timer Output Timing
Execution Cycle
Next Opcode fetch
SLEEP Instruction fetch
T1
T2
TS
TS
~
~
T3
T1
T2
ø
31
INTi
~
~
NMI
32
~
~
33
~ ~
~ ~
~
~
A0–A18
MREQ, M1
RD
43
44
HALT
~
~
Figure 24. SLEEP Execution Cycle
PS014004-1106
Architecture
Z80180
Microprocessor Unit
37
CSIO Receive/Transmit Timing
CSIO CLock
56
56
Transmit data
(Internal Clock)
57
57
Transmit data
(External Clock)
11tcyc
58
11tcyc
58
59
59
Receive data
(Internal Clock)
11.5tcyc
Receive data
(External Clock)
60
16.5tcyc
11.5tcyc
61
16.5tcyc
60
61
Figure 25. CSIO Receive/Transmit Timing
Rise Time and Fall Times
65
EXTAL VIL1
66
VIH1
VIH1
70
69
VIL1
Input Rise
Time and
External
Figure 26. Rise Time and Fall Times
ASCI Register Description
The following sections explain the various functions of the ASCI
registers.
Figure 27 displays the ASCI block diagram.
PS014004-1106
Architecture
Z80180
Microprocessor Unit
38
ASCI Block Diagram
Internal Address/Data Bus
Interrupt Request
TXA0
RXA0
RTS0
CTS0
DCD0
ASCI Transmit Data Register
Ch 0: TDR0
ASCI Transmit Data Register
Ch 1: TDR1
ASCI Transmit Shift Register*
Ch 0: TSR0
ASCI Transmit Shift Register*
Ch 1: TSR1
ASCI Receive Data FIFO
Ch 0: RDR0
ASCI Receive Data FIFO
Ch 1: RDR1
ASCI Receive Shift Register*
Ch 0: RSR0 (8)
ASCI Receive Shift Register*
Ch 1: RSR1 (8)
ASCI Control Register A
Ch 0: CNTLA0 (8)
ASCI
Control
TXA1
RXA1
ASCI Control Register A
Ch 1: CNTLA1 (8)
ASCI Control Register B
Ch 0: CNTB0 (8)
ASCI Control Register B
Ch 1: CNTB1 (8)
ASCI Status FIFO
Ch 0
ASCI Status FIFO
Ch 1
ASCI Status Register
Ch 0: STAT0 (8)
ASCI Status Register
Ch 1: STAT1 (8)
CTS1
Note: *Not Program
Accessible.
CKA0
Baud Rate
Generator 0
CKA1
Baud Rate
Generator 1
φ
Figure 27. ASCI Block Diagram
ASCI Registers
ASCI Transmit Shift Register 0 (TSR0, TSR1)—When the ASCI Transmit Shift
Register (TSR) receives data from the ASCI Transmit Data Register (TDR), the data is
shifted out to the TxA pin. When transmission is completed, the next byte (if available) is
automatically loaded from TDR into TSR and the next transmission starts. If no data is
available for transmission, TSR IDLEs by outputting a continuous High level. This
register is not program accessible.
ASCI Transmit Data Register 0,1 (TDR0, TDR1)— I/O
address = 06h, 07h. Data written to the ASCI Transmit Data Register is
transferred to the TSR as soon as TSR is empty. Data can be written while TSR is shifting out
the previous byte of data. The ASCI transmitter is double buffered.
PS014004-1106
Architecture
Z80180
Microprocessor Unit
39
Data can be written into and read from the ASCI Transmit Data Register. If data is read from
the ASCI Transmit Data Register, the ASCI data transmit operation is not affected by this
READ operation.
ASCI Receive Shift Register 0,1 (RSR0, RSR1)—This register receives data shifted in on
the RxA pin. When full, data is automatically transferred to the ASCI Receive Data Register
(RDR) if it is empty. If RSR is not empty when the next incoming data byte is shifted in, an
overrun error occurs. This register is not program accessible.
ASCI Receive Data FIFO 0,1 (RDR0, RDR1)—I/O Address = 08h, 09h. The ASCI Receive
Data Register is a READ-ONLY register. When a complete incoming data byte is assembled
in RSR, it is automatically transferred to the 4 character Receive Data First-In First-Out
(FIFO) memory. The oldest character in the FIFO (if any) can be read from the Receive Data
Register (RDR). The next incoming data byte can be shifted into RSR while the FIFO is full.
The ASCI receiver is well buffered.
ASCI Transmit Data Registers
Register addresses 06h and 07h hold the ASCI transmit data for channel 0 and channel 1,
respectively.
Channel 0
Mnemonics TDR0 (Address 06h)
7
6
5
4
3
2
1
—-
—
—-
—
—
—
—
ASCI Transmit Channel 0
Figure 28. ASCI Register Channel 0
PS014004-1106
Architecture
Z80180
Microprocessor Unit
40
Channel 1
Mnemonics TDR1 (Address (07h)
7
6
5
4
3
2
1
—-
—
—-
—
—
—
—
ASCI Transmit Channel 1
Figure 29. ASCI Register Channel 1
ASCI Receive Registers
Register addresses 08h and 09h hold the ASCI receive data for channel 0 and channel 1,
respectively.
Channel 0
Mnemonics TSR0 (Address (08h)
ASCI Receive Register Channel 0
7
6
5
4
3
2
1
—
—
—
—
—
—
—
ASCI Receive Data
Figure 30. ASCI Receive Register Channel 0
PS014004-1106
Architecture
Z80180
Microprocessor Unit
41
Channel 1
Mnemonics TSR1 (Address (09h)
ASCI Receive Register Channel 1R
7
6
5
4
3
2
1
—
—
—
—
—
—
—
ASCI Receive Data
Figure 31. ASCI Receive Register Channel 1R
ASCI Channel Control Register A
ASCI Channel Control Register A
ASCI Control Register A 0 (CNTLA0: I/O Address = 00h)
Bit
7
6
5
4
3
2
1
0
MPE
RE
TE
RTS0
MPBR/
EFR
MOD2
MOD1
MOD0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
ASCI Control Register A 1 (CNTLA1: I/O Address = 01h)
Bit
7
6
5
MPE
RE
TE
R/W
R/W
R/W
4
3
2
1
0
__
MPBR/
EFR
MOD2
MOD1
MOD0
R/W
R/W
R/W
R/W
R/W
Figure 32. ASCI Channel Control Register A
MPE: Multi-Processor Mode Enable (bit 7)—The ASCI features a
multiprocessor communication mode that utilizes an extra data bit for selective
communication when a number of processors share a common serial bus. Multiprocessor
data format is selected when the MP bit in CNTLB is set to 1. If multiprocessor mode is not
selected (MP bit in CNTLB = 0), MPE exhibits no effect. If multiprocessor mode is selected,
MPE enables or disables the wake-up feature as follows.
If MBE is set to 1, only received bytes in which the MPB (multiprocessor bit) = 1 can affect
the RDRF and error flags. Effectively, other bytes (with MPB = 0) are ignored by the ASCI. If
PS014004-1106
Architecture
Z80180
Microprocessor Unit
42
MPE is reset to 0, all bytes, regardless of the state of the MPB data bit, affect the REDR and
error flags. MPE is cleared to 0 during RESET.
RE: Receiver Enable (bit 6)—When RE is set to 1, the ASCI transmitter is enabled. When
TE is reset to 0, the transmitter is disables and any transmit operation in progress is
interrupted. However, the TDRE flag is not reset and the previous contents of TDRE are held.
TE is cleared to 0 in IOSTOP mode during RESET.
TE: Transmitter Enable (bit 5)—When TE is set to 1, the ASCI receiver is enabled. When
TE is reset to 0, the transmitter is disabled and any transmit operation in progress is
interrupted. However, the TDRE flag is not reset and the previous contents of TDRE are held.
TE is cleared to 0 in IOSTOP mode during RESET.
RTS0: Request to Send Channel 0 (bit 4 in CNTLA0 only)—If bit 4 of the System
Configuration Register is 0, the RTS0/TxS pin features the RTS0 function. RTS0 allows the
ASCI to control (START/STOP) another communication devices transmission (for example,
by connecting to that device’s CTS input). RTS0 is essentially a 1 bit output port, having no
side effects on other ASCI registers or flags. Bit 4 in CNTLA1 is not used.
MPBR/EFR: Multiprocessor Bit Receive/Error Flag Reset (bit 3)—When multiprocessor
mode is enabled (MP in CNTLB = 1), MPBR, when read, contains the value of the MPB bit for
the most recent receive operation. When written to 0, the EFR function is selected to reset all
error flags (OVRN, FE, PE and BRK in the ASEXT register) to 0. MPBR/EFR is undefined
during RESET.
MOD2, 1, 0: ASCI Data Format Mode 2, 1, 0 (bits 2–0)—These bits program the ASCI
data format as listed in Table 10.
Table 10. ASCI Data Formats Mode 2, 1, 0
Bit
Description
MOD2 = 0
0→7 bit data
MOD2 = 1
1→8 bit data
MOD1 = 0
0→No parity
MOD1 = 1
1→Parity enabled
MOD0 = 0
0→1 stop bit
MOD0 = 1
1→2 stop bits
The data formats available based on all combinations of MOD2, MOD1, and MOD0 are
indicated in Table 11.
PS014004-1106
Architecture
Z80180
Microprocessor Unit
43
Table 11. Data Formats
MOD2
0
0
0
0
1
1
1
1
MOD1
0
0
1
1
0
0
1
1
MOD0
0
1
0
1
0
1
0
1
Data Format
Start + 7 bit data + 1 stop
Start + 7 bit data + 2 stop
Start + 7 bit data + parity + 1 stop
Start + 7 bit data + parity + 2 stop
Start + 8 bit data + 1 stop
Start + 8 bit data + 2 stop
Start + 8 bit data + parity + 1 stop
Start + 8 bit data + parity + 2 stop
ASCI Channel Control Register B
ASCI Channel Control Register B
ASCI Control Register B 0 (CNTLB0: I/O Address = 02h)
ASCI Control Register B 1 (CNTLB1: I/O Address = 03h)
Bit
7
6
5
4
3
2
1
0
MPBT
MP
CTS/
PS
PEO
DR
SS2
SS1
SS0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Figure 33. ASCI Channel Control Register B
MPBT: Multiprocessor Bit Transmit (bit 7)—When multiprocessor communication format
is selected (MP bit = 1), MPBT is used to specify the MPB data bit for transmission. If MPBT
= 1, then MPB = 1 is transmitted. If MPBT = 0, then MPB = 0 is transmitted. MPBT state is
undefined during and after RESET.
MP: Multiprocessor Mode (bit 6)—When MP is set to 1, the data format is configured for
multiprocessor mode based on the MOD2 (number of data bits) and MOD0 (number of stop
bits) bits in CNTLA. The format is as follows.
Start bit + 7 or 8 data bits + MPB bit + 1 or 2 stop bits
Multiprocessor (MP=1) format does not feature any provision for parity.
If MP = 0, the data format is based on MOD0, MOD1, MOD2, and may include parity. The MP
bit is cleared to 0 during RESET.
CTS/PS: Clear to Send/Prescale (bit 5)—If bit 5 of the System Configuration Register
is 0, the CTS0/RxS pin features the CTS0 function, and the state of the pin can be read in bit 5
PS014004-1106
Architecture
Z80180
Microprocessor Unit
44
of CNTLB0 in a real-time, positive-logic fashion (HIGH = 1, LOW = 0). If bit 5 in the System
Configuration Register is 0 to auto-enable CTS0, and the pin is negated (High), the TDRE bit
is inhibited (forced to 0). Bit 5 of CNTLB1 reads back as 0.
If the SS2–0 bits in this register are not 111, and the BRG mode bit in the ASEXT register is 0,
then writing to this bit sets the prescale (PS) control. Under these circumstances, a 0 indicates a divide-by-10 prescale function, while a 1 indicates divide-by-30. The bit resets to 0.
PEO: Parity Even Odd (bit 4)—PEO selects oven or odd parity. PEO does not affect the
enabling/disabling of parity (MOD1 bit of CNTLA). If PEO is cleared to 0, even parity is
selected. If PEO is set to 1, odd parity is selected. PEO is cleared to 0 during RESET.
DR: Divide Ratio (bit 3)—If the X1 bit in the ASEXT register is 0, this bit specifies the
divider used to obtain baud rate from the data sampling clock. If DR is reset to 0, divide- by16 is used, while if DR is set to 1, divide-by-64 is used. DR is cleared to 0 during RESET.
SS2,1,0: Source/Speed Select 2,1,0 (bits 2–0)—If these bits are 111, as they are after
RESET, the CKA pin is used as a clock input, and is divided by 1, 16, or 64 depending on the
DR bit and the X1 bit in the ASEXT register.
If these bits are not 111 and the BRG mode bit is ASEXT is 0, these bits specify a power-oftwo divider for the PHI clock as indicated in Table 12.
Setting or leaving these bits as 111 makes sense for a channel only when its CKA pin is
selected for the CKA function. CKAO/CKS features the CKAO function when bit 4 of the
System Configuration Register is 0. DCD0/CKA1 features the CKA1 function when bit 0 of
the Interrupt Edge register is 1.
Table 12. Divide Ratio
PS014004-1106
SS2
SS1
SS0
Divide Ratio
0
0
0
÷1
0
0
1
÷2
0
1
0
÷4
0
1
1
÷8
1
0
0
÷16
1
0
1
÷32
1
1
0
÷64
1
1
1
External Clock
Architecture
Z80180
Microprocessor Unit
45
ASCI Status Register 0, 1 (STAT0, 1)
Each channel status register allows interrogation of ASCI communication, error and modem
control signal status, and enabling or disabling of ASCI interrupts.
ASCI Status Registers
ASCI Status Register 0 (STAT0: I/O Address = 04h)
Bit
7
6
5
4
3
2
1
0
RDRF
OVRN
PE
FE
RE
DCD0
TDRE
TIE
R
R
R
R
R/W
R
R
R/W
ASCI Status Register 1 (STAT1: I/O Address = 05h)
Bit
7
6
5
4
3
2
1
0
RDRF
OVRN
PE
FE
RE
__
TDRE
TIE
R
R
R
R
R/W
R
R/W
Figure 34. ASCI Status Registers
RDRF: Receive Data Register Full (bit 7)—RDRF is set to 1 when an incoming data
byte is loaded into an empty RxFIFO.
Note: If a framing or parity error occurs, RDRF is still set and the receive data (which
generated the error) is still loaded into the FIFO.
RDRF is cleared to 0 by reading RDR and most recent character in the FIFO from IOSTOP
mode, during RESET and for ASCI0 if the DCD0 input is auto-enabled and is negated (High).
OVRN: Overrun Error (bit 6)—An overrun condition occurs when the receiver finishes
assembling a character, but the RxFIFO is full so that there is no room for the character.
However, this status bit is not set until the most recent character received before the overrun
becomes the oldest byte in the FIFO. This bit is cleared when software writes a 1 to the EFR
bit in the CNTLA register, and also by RESET, in IOSTOP mode, and for ASCI0 if the DCD0
pin is auto enabled and is negated (High).
When an overrun occurs, the receiver does not place the character in the shift register into
the FIFO, nor any subsequent characters, until the last good character comes to the top of the
FIFO so that OVRN is set, and software then writes a 1 to EFR to clear it.
PE: Parity Error (bit 5)—A parity error is detected when parity checking is enabled by
the MOD1 bit in the CNT1LA register being 1, and a character is assembled in which the
parity does not match the PEO bit in the CNTLB register. However, this status bit is not set
until or unless the error character becomes the oldest one in the RxFIFO. PE is cleared when
software writes a 1 to the EFR bit in the CNTRLA register, and also by RESET, in IOSTOP
mode, and for ASCI0 if the DCD0 pin is auto-enabled and is negated (High).
PS014004-1106
Architecture
Z80180
Microprocessor Unit
46
FE: Framing Error (bit 4)—A framing error is detected when the stop bit of a character is
sampled as 0/SPACE. However, this status bit is not set until or unless the error character
becomes the oldest one in the RxFIFO. FE is cleared when software writes a 1 to the EFR bit
in the CNTLA register, and also by RESET, in IOSTOP mode, and for ASCIO if the DCDO
pin is auto-enabled and is negated (High).
REI: Receive Interrupt Enable (bit 3)—RIE must be set to 1 to enable ASCI receive
interrupt requests. When RIE is 1, the receiver requests an interrupt when a character is
received and RDRF is set, but only if neither DMA channel sets its request-routing field to
receive data from this ASCI. That is, if SM1–0 are 11 and SAR17–16 are 10, or DIM1 is 1 and
IAR17–16 are 10, then ASCI1 does not request an interrupt for RDRF. If RIE is 1, either ASCI
requests an interrupt when OVRN, PE or FE is set, and ASCI0 requests an interrupt when
DCD0 goes High. RIE is cleared to 0 by RESET.
DCD0: Data Carrier Detect (bit 2 STAT0)—If bit 0 of the Interrupt Edge Register
(IER0) is 0, the DCD0/CKA1 pin features the DCD0 function, and this bit is set to 1 when the
pin is High. It is cleared to 0 on the first READ of STAT0 following the pin's transition from
High to Low and during RESET. When IER0 is 0, bit 6 of the ASEXT0 register is 0 to select
auto-enabling, and the pin is negated (High), the bit 2 of STAT1 is not used.
TDRE: Transmit Data Register Empty (bit 1)—TDRE = 1 indicates that the TDR is
empty and the next transmit data byte is written to TDR. After the byte is written to TDR,
TDRE is cleared to 0 until the ASCI transfers the byte from TDR to the TSR and then TDRE is
again set to 1. TDRE is set to 1 in IOSTOP mode and during RESET. On ASCIO, if the CTS0
pin is auto-enabled in the ASEXT0 registers and the pin is High, TDRE is reset to 0.
TIE: Transmit Interrupt Enable (bit 0)—TIE must be set to 1 to enable ASCI transmit
interrupt requests. If TIE = 1, an interrupt is requested when TDRE = 1. TIE is cleared to 0
during RESET.
CSIO Control/Status Register
CNTR: I/O Address = 0Ah—CNTR is used to monitor CSIO status, enable and disable the
CSIO, enable and disable interrupt generation, and select the data clock speed and source.
CSIO Control
Bit
7
6
5
4
3
2
1
0
EF
EIE
RE
TE
__
SS2
SS1
SS0
R
R/W
R/W
R/W
R/W
R/W
R/W
Figure 35. CSIO Control Register
EF: End Flag (bit 7)—EF is set to 1 by the CSIO to indicate completion of an 8-bit data
transmit or receive operation. If the End Interrupt Enable (EIE) bit = 1 when EF is set to 1, a
CPU interrupt request is generated. Program access of TRDR only occurs if EF = 1. The CSIO
PS014004-1106
Architecture
Z80180
Microprocessor Unit
47
clears EF to 0 when TRDR is read or written. EF is cleared to 0 during RESET and IOSTOP
mode.
EIE: End Interrupt Enable (bit 6)—EIE is set to 1 to generate a CPU interrupt request.
The interrupt request is inhibited if EIE is reset to 0. EIE is cleared to 0 during RESET.
RE: Receive Enable (bit 5)—A CSIO receive operation is started by setting RE to 1.
When RE is set to 1, the data clock is enabled. In internal clock mode, the data clock is output from the CKS pin. In external clock mode, the clock is input on the CKS pin. In either
case, data is shifted in on the RXS pin in synchronization with the (internal or external) data
clock. After receiving 8 bits of data, the CSIO automatically clears RE to 0, EF is set to 1, and
an interrupt (if enabled by EIE = 1) is generated. RE and TE are never both set to 1 at the
same time. RE is cleared to 0 during RESET and ISTOP mode.
Transmit Enable (bit 4)—A CSIO transmit operation is started by setting TE to 1. When
TE is set to 1, the data clock is enabled. When in internal clock mode, the data clock is output from the CKS pin. In external clock mode, the clock is input on the CKS pin. In either
case, data is shifted out on the TXS pin synchronous with the (internal or external) data
clock. After transmitting 8 bits of data, the CSIO automatically clears TE to 0, EF is set to 1,
and an interrupt (if enabled by EIE = 1) is generated. TE and RE are never both set to 1 at the
same time. TE is cleared to 0 during RESET and IOSTOP mode.
SS2, 1, 0: Speed Select 2, 1, 0 (bits 2-0)—SS2, SS1 and SS0 select the CSIO transmit/
receive clock source and speed. SS2, SS1 and SS0 are all set to 1 during RESET. Table 13 lists
the CSIO Baud Rate selection.
Table 13. CSIO Baud Rate Selection
SS2
SS1
SS0
Divide Ratio
0
0
0
÷20
0
0
1
÷40
0
1
0
÷80
0
1
1
÷160
1
0
0
÷320
1
0
1
÷640
1
1
0
÷1280
1
1
1
External Clock Input
(less than ÷20)
After RESET, the CKS pin is configured as an external clock input (SS2, SS1, SS0 = 1).
Changing these values causes CKS to become an output pin and the selected clock is output
when transmit or receive operations are enabled.
PS014004-1106
Architecture
Z80180
Microprocessor Unit
48
CSIO Transmit/Receive Data Register
(TRDR: I/O Address = 0Bh)
ASCI Receive Register Channel 1R
7
6
5
4
3
2
1
—
—
—
—
—
—
—
CSIO Transmit/Receive Data
Figure 36. CSI/O Receive Register Channel 1R
Timer Data Register Channel 0L
TMDR0L: OCH
ASCI Receive Register Channel 1R
0Ch
7
6
5
4
3
2
1
—
—
—
—
—
—
—
Timer Data
Figure 37. Timer Data Register Channel Low
Timer Data Register Channel 0H
TMDR0H: ODH
Timer Data Register Channel High
0Dh
7
6
5
4
3
2
1
—
—
—
—
—
—
—
Timer Data
Figure 38. Timer Data Register Channel High
PS014004-1106
Architecture
Z80180
Microprocessor Unit
49
Timer Reload Register 0L
RLDR0L: 0EH
Timer Reload Register Low
0Eh
7
6
5
4
3
2
1
—
—
—
—
—
—
—
Timer Reload Data
Figure 39. Timer Reload Register Low
Timer Reload Register 0H
RLDR0H
Timer Reload Register
0Fh
7
6
5
4
3
2
1
—
—
—
—
—
—
—
Timer Reload Data
Figure 40. Timer Reload Register
Timer Control Register (TCR)
TCR monitors both channels (PRT0, PRT1) TMDR status. It also controls enabling and
disabling of down counting and interrupts along with controlling output pin A18/TOUT for
PRT1.
Timer Control Register (TCR: I/O Address = 10h)
Bit
7
6
5
4
3
2
1
0
TIF1
TIF0
TIE1
TIE0
TOC1
TOC0
TDE1
TDE0
R
R
R/W
R/W
R/W
R/W
R/W
R/W
Figure 41. Timer Control Register (TCR: I/O Address = 10h)
PS014004-1106
Architecture
Z80180
Microprocessor Unit
50
TIF1: Timer Interrupt Flag 1 (bit 7)—When TMDR1 decrements to 0, TIF1 is set to 1,
and, when enabled by TIE1 = 1, an interrupt request is generated. TIF1 is reset to 0 when TCR
is read and the higher or lower byte of TMDR1 is read. During RESET, TIF1 is cleared to 0.
TIF0: Timer Interrupt Flag 0 (bit 6)—When TMDR0 decrements to 0, TIF0 is set to 1,
and, when enabled by TIE0 = 1, an interrupt request is generated TIF0 is reset to 0 when TCR
is read and the higher or lower byte of TMDR0 is read. During RESET, TIF0 is cleared to 0.
TIE1: Timer Interrupt Enable 1 (bit 5)—When TIE0 is set to 1, TIF1 = 1 generates a
CPU interrupt request. When TIE0 is reset to 0, the interrupt request is inhibited. During
RESET, TIE0 is cleared to 0.
TOC1, 0: Timer Output Control (bits 3, 2)—TOC1 and TOC0
control the output of PRT1 using the multiplexed TOUT/DREQ pin as
indicated in Table 14. During RESET, TOC1 and TOC0 are cleared to 0. If bit 3 of the IAR1B
register is 1, the TOUT function is selected. By
programming TOC1 and TOC0, the TOUT/DREQ pin can be forced High, Low, or toggled
when TMDR1 decrements to 0.
Table 14. Timer Output Control
TOC1
0
TOC0
0
Output
Inhibited
0
1
1
1
0
1
Toggled
0
1
The TOUT/DREQ pin is not affected by the
PRT.
If bit 3 of IAR1B is 1, the TOUT/DREQ pin
toggles or is set Low or High as indicated.
TDE1, 0: Timer Down Count Enable (bits 1, 0)—TDE1 and TDE0 enable and disable
down counting for TMDR1 and TMDR0, respectively. When TDEn (N = 0,1) is set to 1, down
counting is stopped and TMDRn is freely read or written. TDE1 and TDE0 are cleared to 0
during RESET and TMDRn do not decrement until TDEn is set to 1.
ASCI Extension Control Register Channels 0 and 1
ASEXT0 and ASEXT1
The ASCI Extension Control Register controls functions newly added to the ASCIs in the
Z80180 family.
Note: All bits in this register reset to 0.
PS014004-1106
Architecture
Z80180
Microprocessor Unit
51
ASCI Extension Control Registers, Channel 0 and 1
ASCI Extension Control Register 0(ASEXT0 I/O Address = 12h)
7
Bit
Reserved
7
Bit
6
5
4
3
2
1
0
DCDO
CTSO
XI
BRGO
Mode
Break
Nab
Break
Send
Break
ASCI Extension Control Register 1 (ASEXT1 I/O Address = 13h)
3
5
6
4
2
1
0
Reserved Reserved Reserved
XI
BRGI
Mode
Break
Enab
Break
Send
Break
Figure 42. ASCI Extension Control Registers, Channel 0 and 1
DCD0 dis (bit 6, ASCI0 only)—If bit 0 of the Interrupt Edge Register is 0 to select the
DCD0 function for the DCD0/CKA1 pin, and this bit is 0, the DCD0 pin auto-enables the
ASCI0 receiver. When the pin is negated/High, the Receiver is held in a RESET state. If bit 0
of the IER is 0 and this bit is 1, the state of the DCD-pin has no effect on receiver operation.
In either state of this bit, software can read the state of the DCD0 pin in the STAT0 register,
and the receiver interrupts on a rising edge of DCD0.
CTS0 dis (bit 5, ASCI0 only)—If bit 5 of the System Configuration Register is 0 to
select the CTS0 function of the CTS0/RXS pin, and this bit is 0, then the CTS0 pin autoenables the ASCIO transmitter, in that when the pin is negated (High), the TDRE bit in the
STAT0 register is forced to 0. If bit 5 of the System Configuration Register is 0 and this bit is
1, the state of the CTS0 pin exhibits no effect on the transmitter. Regardless of the state of
this bit, software can read the state of the CTS0 pin the CNTLB0 register.
X1 (bit 4)—If this bit is 1, the clock from the Baud Rate Generator or CKA pin is received
as a 1X bit clock (sometimes called isochronous mode). In this mode, receive data on the
RXA pin must be synchronized to the clock on the CKA pin, regardless of whether CKA is an
input or an output. If this bit is 0, the clock from the Baud Rate Generator or CKA pin is
divided by 16 or 64 per the DR bit in CNTLB register, to obtain the actual bit rate. In this
mode, receive data on the RXA pin is not required to be synchronized to a clock.
BRG Mode (bit 3)—If the SS2–0 bits in the CNTLB register are not 111, and this bit is 0,
the ASCI Baud Rate Generator divides PHI by 10 or 30, depending on the DR bit in CNTLB,
and then by a power of two selected by the SS2–0 bits, to obtain the clock that is presented to
the transmitter and receiver and that can be output on the CKA pin. If SS2–0 are not 111, and
this bit is 1, the Baud Rate Generator divides PHI by twice (the 16-bit value programmed
into the Time Constant Registers, plus 2). This mode is identical to the operation of the baud
rate generator in the ESCC.
Break Enable (bit 2)—If this bit is 1, the receiver detects break conditions and report
them in bit 1, and the transmitter sends breaks under the control of bit 0.
PS014004-1106
Architecture
Z80180
Microprocessor Unit
52
Break Detect (bit 1)—The receiver sets this READ-ONLY bit to 1 when an all-zero
character with a Framing Error becomes the oldest character in the RxFIFO. The bit is
cleared when software writes a 0 to the EFR bit in CNTLA register, also by RESET, by
IOSTOP mode, and for ASCIO if the DCD0 pin is auto-enabled and is negated (High).
Send Break (bit 0)—If this bit and bit 2 are both 1, the transmitter holds the TXA pin Low
to send a break condition. The duration of the break is under software control (one of the
PRTs or CTCs can be used to time it). This bit resets to 0, in which state TXA carries the
serial output of the transmitter.
Timer Data Register Channel 1L
Mnemonic TMDR1L:14H
Timer Data Register
7
6
5
4
3
2
1
0
Timer Data
Figure 43. Timer Data Register Channel 1L
Timer Data Register Channel 1H
Mnemonic TMDR1H: 15H
Timer Data Register
7
6
5
4
3
2
1
0
Timer Data
Figure 44. Timer Data Register Channel 1H
PS014004-1106
Architecture
Z80180
Microprocessor Unit
53
Timer Reload Register Channel 1L
Mnemonic RLDR1L: 16H
Timer Data Register
7
6
5
4
3
2
1
0
Reload Data
Figure 45. Timer Reload Register Channel 1L
Timer Reload Register Channel 1H
Mnemonic RLDR1H: 17H
Timer Data Register
7
6
5
4
3
2
1
0
Reload Data
Figure 46. Timer Reload Register Channel 1H
PS014004-1106
Architecture
Z80180
Microprocessor Unit
54
Free Running Counter I/O Address = 18H
Mnemonic FRC: 18H
If data is written into the free running counter, the interval of DRAM refresh cycle and baud
rates for the ASCI and CSI/O are not guaranteed. In IOSTOP mode, the free running counter
continues counting down. It is initialized to FFH, during RESET.
Timer Data Register
7
6
5
4
3
2
1
0
Counting Data
Figure 47. Timer Data Register
DMA Source Address Register Channel 0
(SAR0: I/O ADDRESS = 20h to 22h) specifies the physical source address for channel 0
transfers. The register contains 20 bits and can specify up to 1024 KB memory addresses or
up to 64 KB I/O addresses. Channel 0 source can be memory, I/O, or memory mapped I/O.
For I/O, the most significant bits of this register identify the REQUEST HANDSHAKE
signal.
DMA Source Address Register, Channel 0L
Mnemonic SAR0L: Address 20h
Timer Data Register
7
6
5
4
3
2
1
0
—
—
—
—
—
—
—
—
DMA Channel 0 Address
Figure 48. DMA Channel 0L
PS014004-1106
Architecture
Z80180
Microprocessor Unit
55
DMA Source Address Register, Channel 0H
Mnemonic SAR0H: Address 21h
Timer Data Register
7
6
5
4
3
2
1
0
—
—
—
—
—
—
—
—
DMA Channel 0 Address
Figure 49. DMA Channel 0H
DMA Source Address Register Channel 0B
Mnemonics SAR0B: Address 22h
Timer Data Register
7
6
5
4
3
2
1
0
—
—
—
—
—
—
—
—
DMA Channel B Address
Figure 50. DMA Channel 0B
DMA Destination Address Register Channel 0
(DAR0: I/O ADDRESS = 23h to 25h) specifies the physical destination address for channel 0
transfers. The register contains 20 bits and can specify up to 1024 KB memory addresses or
up to 64 KB I/O addresses. Channel 0 destination can be memory, I/O, or memory mapped I/
O. For I/O, the most significant bits of this register identify the REQUEST HANDSHAKE
signal for channel 0.
PS014004-1106
Architecture
Z80180
Microprocessor Unit
56
DMA Destination Address Register Channel 0L
Mnemonic DAR0L: Address 23h
DMA Destination Address Register Channel 0L
7
6
5
4
3
2
1
0
—
—
—
—
—
—
—
—
DMA Channel 0L Address
Figure 51. DMA Destination Address Register Channel 0L
DMA Destination Address Register Channel 0H
Mnemonic DAR0H: Address 24h
DMA Destination Address Register Channel 0H
7
6
5
4
3
2
1
0
—
—
—
—
—
—
—
—
DMA Channel 0H Address
Figure 52. DMA Destination Address Register Channel 0H
DMA Destination Address Register Channel 0B
Mnemonic DAR0B: Address 25h
DMA Destination Address Register Channel 0B
3
—
2
—
1
—
0
—
DMA Channel B Address
Figure 53. DMA Destination Address Register Channel 0B
PS014004-1106
Architecture
Z80180
Microprocessor Unit
57
In the R1 and Z Mask, these DMA registers are expanded from 4 bits to 3 bits in the
Note: package version of CP-68.
Table 15. DMA Transfer Requests
A19*
X
X
X
X
A18
X
X
X
X
A17
0
0
1
1
A16
0
1
0
1
DMA Transfer Request
DREQ0
TDR0 (ASCI0)
TDR1 (ASCI1)
Not Used
DMA Byte Count Register Channel 0
(BCRO: I/O ADDRESS = 26h to 27h) specifies the number of bytes to be transferred. This register contains 16 bits and may specify up to 64 KB transfers. When one byte is transferred,
the register is decremented by 1. If n bytes are transferred, n must be stored before the DMA
operation.
Note: All DMA Count Register channels are undefined during RESET.
DMA Byte Count Register Channel 0L
Mnemonic BCR0L: Address 26h
DMA Byte Count Register
7
6
5
4
3
2
1
0
Counting Data
Figure 54. DMA Byte Count Register 0L
PS014004-1106
Architecture
Z80180
Microprocessor Unit
58
DMA Byte Count Register Channel 0H
Mnemonic BCR0H: Address 27h
DMA Byte Count Register 0H
7
6
5
4
3
2
1
0
Counting Data
Figure 55. DMA Byte Count Register 0H
DMA Byte Count Register Channel 1L
Mnemonic BCR1L: Address 2Eh
DMA Byte Count Register 1L
7
6
5
4
3
2
1
0
Counting Data
Figure 56. DMA Byte Count Register 1L
PS014004-1106
Architecture
Z80180
Microprocessor Unit
59
DMA Byte Count Register Channel 1H
Mnemonic BCR1H: Address 2Fh
DMA Byte Count Register 0H
7
6
5
4
3
2
1
0
Counting Data
Figure 57. DMA Byte Count Register 1H
DMA Memory Address Register Channel 1
(MAR1: I/O ADDRESS = 28h to 2Ah) specifies the physical memory address for channel 1
transfers, which may also be a destination or source memory address. The register contains
20 bits and may specify up to 1024-KB memory address.
DMA Memory Address Register, Channel 1L
Mnemonic MAR1L: Address 28h
DMA Memory Address Register, Channel 1L
7
6
5
4
3
2
1
0
—
—
—
—
—
—
—
—
DMA Memory Address
Figure 58. DMA Memory Address Register, Channel 1L
PS014004-1106
Architecture
Z80180
Microprocessor Unit
60
DMA Memory Address Register, Channel 1H
Mnemonic MAR1H: Address 29h
DMA Memory Address Register, Channel 1H
7
6
5
4
3
2
1
0
—
—
—
—
—
—
—
—
DMA Memory Address
Figure 59. DMA Memory Address Register, Channel 1H
DMA Memory Address Register, Channel 1B
Mnemonic MAR1B (Address 2A)
DMA
3
—
2
—
1
—
0
—
DMA Memory Channel B Address
Figure 60. DMA Memory Address Register, Channel 1B
DMA I/O Address Register Channel 1
(IAR1: I/O ADDRESS = 2Bh to 2Dh) specifies the I/O address for channel 1 transfers, which
may also be a destination or source I/O address. The
register contains 16 bits of I/O address; its most significant byte identifies the REQUEST
HANDSHAKE signal and controls the Alternating Channel feature.
All bits in IAR1B reset to 0.
PS014004-1106
Architecture
Z80180
Microprocessor Unit
61
IAR MS Byte Register (IARIB: I/O Address 2Dh)
Bit
5
7
6
A/T
F
A/T
C
4
3
1
2
TOUT
DREQ
0
Req 1 Sel
Figure 61. IAR MS Byte Register (IARIB: I/O Address 2Dh
DMA I/O Address Register Channel 1L
Mnemonic IAR1L (Address 2B)
DMA I/O Address Register Channel 1L
7
6
5
4
3
2
1
0
—
—
—
—
—
—
—
—
DMA I/O Channel 1L Address
Figure 62. DMA I/O Address Register Channel 1L
DMA I/O Address Register Channel 1H
Mnemonic IAR1H (Address 2C)
DMA I/O Address Register Channel 1H
7
6
5
4
3
2
1
0
—
—
—
—
—
—
—
—
DMA I/O Address Channel 1H
Figure 63. DMA I/O Address Register Channel 1H
PS014004-1106
Architecture
Z80180
Microprocessor Unit
62
DMA I/O Address Register Channel 1B
Mnemonic IAR1B (Address 2D)
DMA I/O Address Register Channel 1B
3
—
2
—
1
—
0
—
DMA I/O Channel B Address
Figure 64. DMA I/O Address Register Channel 1B
DMA Status Register (DSTAT)
DSTAT is used to enable and disable DMA transfer and DMA termination interrupts. DSTAT
also indicates DMA transfer status, in other words, completed or in progress.
Mnemonic DSTAT (Address 30)
DMA Status Register (DSTAT: I/O Address = 30h)
Bit
1
7
6
5
4
3
2
DE1
DE0
DWE1
DWE0
DIE1
DIE0
DME
R/W
R/W
W
W
R/W
R/W
R
0
Figure 65. DMA Status Register (DSTAT: I/O Address = 30h)
DE1: DMA Enable Channel 1 (bit 7)—When DE1 = 1 and DME = 1, channel 1 DMA is
enabled. When a DMA transfer terminates (BCR1 = 0), DE1 is reset to 0 by the DMAC.
When DE1 = 0 and the DMA interrupt is enabled (DIE1 = 1), a DMA interrupt request is
made to the CPU.
To perform a software WRITE to DE1, DWE1 must be written with 0 during the same register
WRITE access. Writing DE1 to 0 disables channel 1 DMA, but DMA is restartable. Writing
DE1 to 1 enables channel 1 DMA and automatically sets DME (DMA Main Enable) to 1.
DE1 is cleared to 0 during RESET.
DE0: DMA Enable Channel 0 (bit 6)—When DE0 = 1 and DME = 1, channel 0 DMA is
enabled. When a DMA transfer terminates (BCR0 = 0), DE0 is reset to 0 by the DMAC.
PS014004-1106
Architecture
Z80180
Microprocessor Unit
63
When DE0 = 0 and the DMA interrupt is enabled (DIE0 = 1), a DMA interrupt request is
made to the CPU.
To perform a software WRITE to DE0, DWE0 must be written with 0 during the same register
WRITE access. Writing DE0 to 0 disables channel 0 DMA. Writing DE0 to 1 enables channel
0 DMA and automatically sets DME (DMA Main Enable) to 1. DE0 is cleared to 0 during
RESET.
DWE1: DE1 Bit WRITE Enable (bit 5)—When performing any
software WRITE to DE1, DWE1 must be written with 0 during the same access. DWE1
always reads as 1.
DWE0: DE0 Bit WRITE Enable (bit 4)—When performing any
software WRITE to DE0, DWE0 must be written with 0 during the same access. DWE0
always reads as 1.
DIE1: DMA Interrupt Enable Channel 1 (bit 3)—When DIE0 is set to 1, the
termination channel 1 DMA transfer (indicated when DE1 = 0) causes a CPU interrupt
request to be generated. When DIE0 = 0, the channel 0 DMA termination interrupt is
disabled. DIE0 is cleared to 0 during RESET.
DIE0: DMA Interrupt Enable Channel 0 (bit 2)—When DIE0 is set to 1, the
termination channel 0 of DMA transfer (indicated when DE0 = 0) causes a CPU interrupt
request to be generated. When DIE0 = 0, the channel 0 DMA termination interrupt is disabled. DIE0 is cleared to 0 during RESET.
DME: DMA Main Enable (bit 0)—A DMA operation is only enabled when its DE bit
(DE0 for channel 0, DE1 for channel 1) and the DME bit is set to 1.
When NMI occurs, DME is reset to 0, disabling DMA activity during the NMI interrupt
service routine. To restart DMA, DE– and/or DE1 must be written with a 1 (even if the
contents are already 1). This WRITE automatically sets DME to 1, allowing DMA operations
to continue.
Note: DME cannot be directly written. It is cleared to 0 by NMI or indirectly set to 1 by
setting DE0 and/or DE1 to 1. DME is cleared to 0 during RESET.
DMA Mode Register (DMODE)
DMODE is used to set the addressing and transfer mode for channel 0.
PS014004-1106
Architecture
Z80180
Microprocessor Unit
64
Mnemonic DMODE
Address 31h
DMA Mode Register (DMODE: I/O Address = 31h)
Bit
7
6
5
4
3
2
1
DM1
DM0
SM1
SM0
MMOD
R/W
R/W
R/W
R/W
R/W
0
Figure 66. DMA Mode Register (DMODE: I/O Address = 31h)
DM1, DM0: Destination Mode Channel 0 (bits 5,4)—Specifies whether the
destination for channel 0 transfers is memory or I/O, and whether the address must be incremented or decremented for each byte transferred. DM1 and DM0 are cleared to 0 during
RESET (see Table 16).
Table 16. Channel 0 Destination
DM1
0
0
1
1
DM0
0
1
0
1
Memory I/O
Memory
Memory
Memory
I/O
Memory Increment/Decrement
+1
–1
fixed
fixed
SM1, SM0: Source Mode Channel 0 (bits 3, 2)—Specifies whether the source for
channel 0 transfers is memory or I/O, and whether the address must be incremented or
decremented for each byte transferred (see Table 17).
Table 17. Channel 0 Source
SM1
0
0
1
1
SM0
0
1
0
1
Memory I/O
Memory
Memory
Memory
I/O
Memory Increment/Decrement
+1
–1
fixed
fixed
Table 18 lists all DMA transfer mode combinations of DM0, DM1, SM0, and SM1. Because
I/O to/from I/O transfers are not implemented, 12 combinations are available.
PS014004-1106
Architecture
Z80180
Microprocessor Unit
65
MMOD: Memory Mode Channel 0 (bit 1). When channel 0 is configured for memory
to/from memory transfers there is no REQUEST HANDSHAKE signal to control the transfer
timing. Instead, two automatic transfer timing modes are selectable: burst (MMOD = 1) and
cycle steal (MMOD = 0). For burst memory to/from memory transfers, the DMAC takes
control of the bus continuously until the DMA transfer completes (the byte count register is
0). In CYCLE STEAL mode, the CPU is provided a cycle for each DMA byte transfer cycle
until the transfer is completed.
For channel 0 DMA with I/O source or destination, the selected REQUEST HANDSHAKE
signal times the transfer and MMOD is ignored. MMOD is cleared to 0 during RESET.
DMA/WAIT Control Register (DCNTL)
DCNTL controls the insertion of wait states into DMAC (and CPU) accesses of memory or
I/O. DCNTL also defines the Request signal for each channel as level or edge sense. DCNTL
also sets the DMA transfer mode for channel 1, which is limited to memory to/from I/O
transfers.
DMA/WAIT Control Register (DCNTL: I/O Address = 32h)
Bit
7
6
5
4
3
2
1
0
MWI1
MWI0
IWI1
IWI0
DMS1
DMS0
DIM1
DIM0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Figure 67. DMA/WAIT Control Register (DCNTL: I/O Address = 32h
MWI1, MWI0: Memory Wait Insertion (bits 7-6)—Specifies the number of wait states
introduced into CPU or DMAC memory access cycles. MWI1 and MWI0 are set to 1 during
RESET.
IWI1, IWI0: I/O Wait Insertion (bits 5-4)—Specifies the number of wait states
introduced into CPU or DMAC I/O access cycles. IWI1 and IWI0 are set to 1 during RESET.
DMS1, DMS0: DMA Request Sense (bits 3-2)—DMS1 and DMS0 specify the DMA
request sense for channel 0 and channel 1 respectively. When reset to 0, the input is level
sense. When set to 1, the input is edge sense. DMS1 and DMS0 are cleared to 0 during
RESET.
Typically, for an input/source device, the associated DMS bit must be
programmed as 0 for level sense because the device undertakes a relatively long period to
update its REQUEST signal after the DMA channel reads data from it in the first of the two
machine cycles involved in transferring a byte.
An output/destination device takes much less time to update its REQUEST signal, after the
DMA channel starts a WRITE operation to it, as the
PS014004-1106
Architecture
Z80180
Microprocessor Unit
66
second machine cycle of the two cycles involved in transferring a byte. With zero-wait state
I/O cycles, which apply only to the ASCIs, it is impossible for a device to update its
REQUEST signal in time, and edge sensing must be used.
With one-wait-state I/O cycles (the fastest possible except for the ASCIs), it is unlikely that
an output device is able to update its REQUEST in time, and edge sense is required for output
to the ESCC and bidirectional Centronics controller, and is recommended for external output
devices connected to TOUT/DREQ.
With two or more wait states in I/O cycles, external output devices on TOUT/DREQ can use
edge or level sense depending on their characteristics; edge sense is still recommended for
output on the ESCC and bidirectional Centronics controller.
DIM1, DIM0: DMA Channel 1 I/O and Memory Mode (bits 1-0)—Specifies the
source/destination and address modifier for channel 1 memory to/from I/O transfer modes.
DIM1 and DIM0 are cleared to 0 during RESET.
Interrupt Vector Low Register
Table 18. Channel 1 Transfer Mode
DIM1
0
0
1
1
DMI0
0
1
0
1
Transfer Mode
Memory→I/O
Memory→I/O
I/O→Memory
I/O→Memory
Address Increment/Decrement
MAR1 +1, IAR1 fixed
MAR1–1, IAR1 fixed
IAR1 fixed, MAR1 + 1
IAR1 fixed, MAR1 –1
Mnemonic: IL
Address 33
Bits 7–5 of IL are used as bits 7–5 of the synthesized interrupt vector during interrupts for the
INT1 and INT2 pins and for the DMAs, ASCIs, PRTs, and CSIO. These three bits are cleared
to 0 during RESET (Figure 68).
Interrupt Vector Low Register (IL: I/O Address = 33h)
Bit
7
6
5
4
3
2
1
0
IL 7
IL 6
IL 5
––
––
––
––
––
R/W
R/W
R/W
Programmable
Interrupt Source Dependent Code
Figure 68. Interrupt Vector Low Register (IL: I/O Address = 33h)
PS014004-1106
Architecture
Z80180
Microprocessor Unit
67
Int/TRAP Control Register
Mnemonics ITC
Address 34
INT/TRAP Control Register (ITC, I/O Address 34h)
This register is used in handling TRAP interrupts and to enable or disable Maskable Interrupt
Level 0 and the INT1 and INT2 pins.
Bit
7
6
5
4
3
2
1
0
TRAP
UFO
––
––
––
ITE2
ITE1
ITE0
R/W
R/W
R/W
R/W
R
Figure 69. Int/TRAP Control Register
TRAP (bit 7)—This bit is set to 1 when an undefined opcode is fetched. TRAP can be reset
under program control by writing it with a 0, however, it cannot be written with 1 under program control. TRAP is reset to 0 during RESET.
UFO: Undefined Fetch Object (bit 6)—When a TRAP interrupt occurs, the contents of
a UFO allow the starting address of the undefined instruction to be determined. However, the
TRAP may occur on either the second or third byte of the opcode. A UFO allows the stacked
Program Counter (PC) value to be correctly adjusted. If UFO = 0, the first opcode must be
interpreted as the stacked PC-1. If UFO = 1, the first opcode address is stacked PC-2. UFO is
READ-ONLY.
ITE2, 1, 0: Interrupt Enable 2, 1, 0 (bits 2-0)—ITE2 and ITE1 enable and disable the
external interrupt inputs INT2 and INT1, respectively. ITE0 enables and disables interrupts
from the on-chip ESCC, CTCs and bidirectional Centronics controller as well as the external
interrupt input INT0. A 1 in a bit enables the corresponding interrupt level while a 0 disables
it. A RESET clears ITE0 to 1 and clears ITE1 and ITE2 to 0.
TRAP Interrupt
The Z80180 generates a nonmaskable (not affected by the state of IEF1) TRAP interrupt
when an undefined opcode fetch occurs. This feature can be used to increase software reliability, implement an extended instruction set, or both. TRAP may occur during opcode fetch
cycles and also if an undefined opcode is fetched during the interrupt acknowledge cycle for
INT0 when Mode 0 is used.
PS014004-1106
Architecture
Z80180
Microprocessor Unit
68
When a TRAP interrupt occurs, the Z80180 operates as follows:
1. The TRAP bit in the Interrupt TRAP/Control (ITC) register is set to 1.
2. The current Program Counter (PC) value, reflecting the location of the undefined
opcode, is saved on the stack.
3. The Z80180 vectors to logical address 0.
Note: If logical address 0000h is mapped to physical address 00000h, the vector is the
same as for RESET. In this case, testing the TRAP bit in ITC reveals whether the
restart at physical address 00000h was caused by RESET or TRAP.
All TRAP interrupts occur after fetching an undefined second opcode byte following one of
the prefix opcodes CBh, DDh, EDh, or FDh, or after fetching an undefined third opcode byte
following one of the double-prefix opcodes DDCBh or FDCBh.
The state of the Undefined Fetch Object (UFO) bit in ITC allows TRAP software to correctly
adjust the stacked PC, depending on whether the second or third byte of the opcode generated the TRAP. If UFO = 0, the starting address of the invalid instruction is equal to the
stacked PC-1. If UFO = 1, the starting address of the invalid instruction is equal to the stacked
PC-2.
Restart
from 0000h
φ
T1
T2
T3
A0–A18 (A19)
TTP Ti
Ti
PC
D0–D7
Opcode
Fetch Cycle
PC Stacking
2nd Opcode
Fetch Cycle
Ti
Ti
Ti
T1 T2
T3
T1
T2
T3
SP-1
SP-2
PCH
PCL
T1
T2
T3
0000h
Undefined
Opcode
M1
MREQ
RD
WR
Figure 70. TRAP Timing—2nd Opcode Undefined
TRAP Timing—2nd Op Code Undefined
PS014004-1106
Architecture
Z80180
Microprocessor Unit
69
TRAP Timing—3rd Op Code Undefined
Restart
from 0000h
Memory
READ Cycle
3nd Opcode
Fetch Cycle
T1 T2 T3 T1 T2 TTP T3 Ti
φ
PC
A0–A18 (A19)
Ti
Ti
T1 T2 T3
Ti
IX + d, IY + d
T1 T2 T3
SP-1
T1 T2 T3
0000h
SP-2
PC-1H
D0–D7
Opcode
Fetch Cycle
PC Stacking
PC-1L
Undefined
Opcode
M1
MREQ
RD
WR
Figure 71. TRAP Timing—3rd Opcode Undefined
Refresh Control Register
Mnemonic RCR (Address 36)
Refresh Control Register (RCA: I/O Address = 36h)
7
-
6
5
4
3
2
1
0
—
—
—
—
—
—
—
—
REFE
Cyc0
REFW
Cyc1
Reserved
Figure 72. Refresh Control Register (RCA: I/O Address = 36h)
The RCR specifies the interval and length of refresh cycles, while enabling or disabling the
refresh function.
REFE: Refresh Enable (bit 7)— REFE = 0 disables the refresh controller, while
REFE = 1 enables refresh cycle insertion. REFE is set to 1 during RESET.
REFW: Refresh Wait (bit 6)—REFW = 0 causes the refresh cycle to be two clocks in
duration. REFW = 1 causes the refresh cycle to be three clocks in duration by adding a
refresh wait cycle (TRW). REFW is set to 1 during RESET.
PS014004-1106
Architecture
Z80180
Microprocessor Unit
70
CYC1, 0: Cycle Interval (bit 1,0)—CYC1 and CYC0 specify the interval (in clock
cycles) between refresh cycles. In the case of dynamic RAMs requiring 128 refresh cycles
every 2 ms (or 256 cycles in every 4 ms), the required refresh interval is less than or equal to
15.625 µs. The underlined values indicate the best refresh interval depending on CPU clock
frequency. CYC0 and CYC1 are cleared to 0 during RESET (see Table 19).
Table 19. DRAM Refresh Intervals
Time Interval
CYC1 CYC0 Insertion Interval Ø: 10 MHz
8 MHz
6 MHz
4 MHz
2.5 MHz
0
0
10 states
(1.0 µs)*
(1.25 µs)* 1.66 µs 2.5 µs
4.0 µs
0
1
20 states
(2.0 µs)*
(2.5 µs)*
3.3 µs
5.0 µs
8.0 µs
1
0
40 states
(4.0 µs)*
(5.0 µs)*
6.6 µs
10.0 µs 16.0 µs
1
1
80 states
(8.0 µs)*
(10.0 µs)* 13.3 µs 20.0 µs 32.0 µs
*Calculated interval.
Refresh Control and RESET
After RESET, based on the initialized value of RCR, refresh cycles occur with an interval of
10 clock cycles and be 3 clock cycles in duration.
Dynamic RAM Refresh Operation
1. REFRESH CYCLE insertion is stopped when the CPU is in the following states:
a. During RESET
b. When the bus is released in response to BUSREQ
c. During SLEEP mode
d. During WAIT states
2. Refresh cycles are suppressed when the bus is released in response to BUSREQ.
However, the refresh timer continues to operate. The time at which the first refresh cycle
occurs after the Z80180 reacquires the bus depends on the refresh timer, and possesses
no timing relationship with the bus exchange.
3. Refresh cycles are suppressed during SLEEP mode. If a refresh cycle is requested during
SLEEP mode, the refresh cycle request is internally latched (until replaced with the next
refresh request). The latched refresh cycle is inserted at the end of the first machine
cycle after SLEEP mode is exited. After this initial cycle, the time at which the next
refresh cycle occurs depends on the refresh time and carries no relationship with the exit
from SLEEP mode.
PS014004-1106
Architecture
Z80180
Microprocessor Unit
71
4. The refresh address is incremented by one for each successful refresh cycle, not for each
refresh. Independent of the number of missed refresh requests, each refresh bus cycle
uses a refresh address incremented by one from that of the previous refresh bus cycles.
MMU Common Base Register
Mnemonic CBR
Address 38
MMU Common Base Register (CBR)—CBR specifies the base address (on 4-KB
boundaries) used to generate a 20-bit physical address for Common Area 1 accesses. All bits
of CBR are reset to 0 during RESET.
MMU Bank Base Register (BBR: I/O Address = 39h)
Bit
7
6
5
4
3
2
1
0
CB7
CB6
CB5
CB4
CB3
CB2
CB1
CB0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Figure 73. MMU Bank Base Register (BBR: I/O Address = 39h)
MMU Bank Base Register (BBR)
Mnemonic BBR
Address 39
BBR specifies the base address (on 4-KB boundaries) used to generate a 19-bit physical
address for Bank Area accesses. All bits of BBR are reset to 0 during RESET.
MMU Bank Base Register (BBR: I/O Address = 39h)
7
6
5
4
3
2
1
0
BB7
BB6
BB5
BB4
BB3
BB2
BB1
BB0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Bit
Figure 74. MMU Bank Base Register (BBR: I/O Address = 39h)
PS014004-1106
Architecture
Z80180
Microprocessor Unit
72
MMU Common/Bank Area Register (CBAR)
Mnemonic CBAR
Address 3A
CBAR specifies boundaries within the Z80180 64-KB logical address space for up to three
areas: Common Area, Bank Area and Common
Area 1.
MMU Common/Bank Area Register (CBAR: I/O Address = 3 AH
7
6
5
4
3
2
1
0
CA3
CA2
CA1
CA0
BA3
BA2
BA1
BA0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Bit
Figure 75. MMU Common/Bank Area Register (CBAR: I/O Address = 3 AH
CA3–CA0:CA (bits 7-4)—CA specifies the start (Low) address
(on 4 KB boundaries) for the Common Area 1, and also determines the most recent address
of the Bank Area. All bits of CA are set to 1 during RESET.
BA–BA0 (bits 3-0)—BA specifies the start (Low) address (on 4-KB boundaries) for the
Bank Area, and also determines the most recent address of the Common Area 0. All bits of
BA are set to 1 during RESET.
Operation Mode Control Register
Mnemonic OMCR
Address 3E
The Z80180 is descended from two different ancestor processors, ZiLOG's original Z80 and
the Hitachi 64180. The Operating Mode
PS014004-1106
Architecture
Z80180
Microprocessor Unit
73
Control Register (OMCR) can be programmed to select between certain differences between
the Z80 and the 64180.
Operating Control OMCR: I/O Address = 3Eh)
D7 D6 D5 — — — — —
Reserved
IOC (R/W)
M1TE (W)
M1E (R/W)
Figure 76. Operating Control Register (OMCR: I/O Address = 3Eh
M1E (M1 Enable)—This bit controls the M1 output and is set to a 1
during reset.
When M1E = 1, the M1 output is asserted Low during the opcode fetch cycle, the INT0
acknowledge cycle, and the first machine cycle of the NMI acknowledge.
On the Z80180, this choice makes the processor fetch a RETI instruction one time only, and
when fetching a RETI from zero-wait-state memory, uses three clock machine cycles which
are not fully Z80-timing compatible, but are compatible with the on-chip CTCs.
When MIE = 0, the processor does not drive M1 Low during instruction fetch cycles. After
fetching a RETI instruction one time only with normal timing, the processor refetches the
instruction using fully Z80-compatible cycles that include driving M1 Low. As a result,
some external Z80 peripherals may require properly decoded RETI instruction.
φ
A0–A18 (A19)
D0–D7
T1
T2
T3
T1
T2
T3
PC+1
PC
EDh
TI
4Dh
TI
TI
T1
T2
T3
TI
T1
T2
T3
PC
PC+1
EDh
4Dh
TI
M1
MREQ
RD
ST
Figure 77. RETI Instruction Sequence with MIE=0
PS014004-1106
Architecture
Z80180
Microprocessor Unit
74
I/O Control Register (ICR)
ICR allows relocating of the internal I/O addresses. ICR also controls enabling/disabling of
the IOSTOP mode (Figure 78).
I/O Control Register (ICR: I/O Address = 3Fh)
Bit
7
6
5
IOA7
IOA6
IOSTP
R/W
R/W
R/W
4
—
3
2
1
0
—
—
—
—
Figure 78. I/O Control Register (ICR: I/O Address = 3Fh)
IOA7, 6: I/O Address Relocation (bits 7,6)
IOA7 and IOA6 relocate internal I/O as illustrated in Figure 79.
Note: The high-order 8 bits of 16-bit internal I/O address are always 0. IOA7 and IOA6 are
cleared to 0 during RESET.
00FFh
IOA7–IOA6 = 1 1
00C0h
00BFh
IOA7–IOA6 = 1 0
0080h
0070h
IOA7– IOA6 = 0 1
0040h
003Fh
IOA7–IOA6 = 0 0
0000h
Figure 79. I/O Address Relocation
IOSTP: IOSTOP Mode (bit 5)—IOSTOP mode is enabled when IOSTP is set to 1. Normal
I/O operation resumes when IOSTOP is reprogrammed or RESET to 0.
PS014004-1106
Architecture
Z80180
Microprocessor Unit
75
Package Information
Figure 80. 80-Pin QFP Package Diagram
PS014004-1106
Package Information
Z80180
Microprocessor Unit
76
Figure 81. 64-Pin DIP Package Diagram
PS014004-1106
Package Information
Z80180
Microprocessor Unit
77
68-Pin PLCC Package Diagram
Figure 82. 68-Pin PLCC Package Diagram
PS014004-1106
Package Information
Z80180
Microprocessor Unit
78
Ordering Information
Table 20. Ordering Information
Z80180
6, 8, 10, 20, 33 MHz
Z8018010FSC
Z8018010PSC
Z8018010VSC
For fast results, contact your local ZiLOG sales office for assistance in ordering the part
required.
Codes
Package
F = Plastic Quad Flatpack
P = Plastic Dual In Line
V = Plastic Leaded Chip Carrier
S = 0 °C to +70 °C
6 = 6 MHz
8 = 8 MHz
10 = 10 MHz
C = Plastic Standard
Temperature
Speed
Environmental
Example:
The Z80180 is a 10-MHz DIP, 0 ºC to 70 ºC, with Plastic
Standard Flow.
Z
80180
10
P
S
C
ZiLOG Prefix
Product Number
Speed
Package
Temperature
Environmental Flow
PS014004-1106
Ordering Information
Z80180
Microprocessor Unit
79
Customer Support
If you experience any problems while operating this product, please check the ZiLOG
Knowledge Base:
http://kb.zilog.com/kb/oKBmain.asp
If you cannot find an answer or have further questions, please see the ZiLOG Technical
Support web page:
http://support.zilog.com
PS014004-1106
Customer Support